2015 Volkswagen Golf, Golf Variant Repair Manual - PDF DOWNLOAD

Golf 2015 ➤ , Golf Variant 2015 ➤ Engine Mechanical, Fuel Injection and Ignition - Edition 04.2015 – Disconnect the connector -3-. – Remove the nuts -1- and the Oil Level Thermal Sensor - G266-4-.

es, in part or in w l purpos hole ercia , is n m ot p om c r erm o e t a itte riv du p or nl f e g n

ility ab y li an pt ce

Installing

n AG. Volkswagen AG do es n wage s k l ot g o yV ua b d ran ir se tee o h t or u ac a ss

Install in reverse order of removal. Note the following:

rrectness of i t to the co nform spec at i h re o n wit in t his

– Replace the O-ring -2-.

– Fill with engine oil and then check the level. Refer to ⇒ Main‐ tenance ; Booklet 36.1 ; Procedure Descriptions; Engine Oil, Draining, Replacing Oil Filter, and Filling . Tightening Specifications

♦ Refer to ⇒ “1.1 Overview - Oil Pan/Oil Pump”, page 179

do c um en

ht rig py Co t.

1. Oil Pan/Oil Pump

191

agen lksw Vo by

AG.

Prote cted by

c o p yri gh t . C op yi

Turn static files into dynamic content formats.

Create a flipbook

Articles inside

1.4 Knock Sensor 1 G61 , Removing and Installing

1.6 Engine Speed Sensor G28 , Removing and Installing

1.5 Camshaft Position Sensor, Removing and Installing

2.2 Catalytic Converter, Removing and Installing

t1.3 Muffler, Removing and Installing

r1.4 Exhaust System, Installing without Tension

C1.6 Clamping Sleeve Installation Position

g1.5 Exhaust System, Checking for Leaks

o1.2 Exhaust Pipes/Mufflers, Separating

8.3 Oxygen Sensor 1 after Catalytic Converter GX7 , Removing and Installing

7.2 High Pressure Pump, Removing and Installing

s9 Special Tools

5.4 Low Fuel Pressure Sensor G410 , Removing and Installing

5.3 Fuel Pressure Sensor G247 , Checking

5.2 Fuel Pressure Sensor G247 , Removing and Installing

4.6 Throttle Valve Control Module, Cleaning

4.3 Intake Manifold, Removing and Installing

4.2 Overview - Intake Manifold Lower Section with Fuel Rail

3.2 Air Filter Housing, Removing and Installing

2.4 Fuel Injector Seals, Replacing

2.3 Intake Manifold-Fuel Injectors, Removing and Installing

2.5 Fuel Injectors, Cleaning

1.2 High Fuel Pressure, Reducing

3 Special Tools

4.7 Auxiliary Cooler, Removing and Installing

1.2 Turbocharger, Removing and Installing

5 Special Tools

4.5 Fan Shroud, Removing and Installing

c4.2 Overview - Auxiliary Cooler

4.6 Coolant Fan, Removing and Installing

r3.3 Upper Coolant Pipes, Removing and Installing

e2.11 Engine Coolant Temperature Sensor on Radiator Outlet G83 , Removing and Installing

c2.10 Engine Coolant Temperature Sensor G62 , Removing and Installing

2.9 Engine Temperature Control Actuator N493 , Removing and Installing

s2.7 Coolant Pump, Removing and Installing

2.2 Overview - Electric Coolant Pump

n2.6 Transmission Coolant Valve N488 , Removing and Installing

1.3 Coolant, Draining and Filling

1.2 Coolant System, Checking for Leaks

5 Special Tools

4.6 Oil Pressure, Checking

4.8 Oil Pressure Regulation Valve N428 , Removing and Installing

4.7 Piston Cooling Nozzle Control Valve N522 , Removing and Installing

4.5 Oil Pressure Switch, Level 3 F447 , Removing and Installing

4.4 Reduced Oil Pressure Switch F378 , Removing and Installing

4.3 Oil Pressure Switch F1 , Removing and Installing

4.2 Overview - Oil Pressure Switch/Oil Pressure Regulator Valve

3.2 Oil Separator, Removing and Installing

2.3 Mechanical Switch Valve, Removing and Installing

1.5 Oil Pump, Removing and Installing

1.6 Oil Level Thermal Sensor G266 , Removing and Installing

6 Special Tools

4.6 Valve Stem Seals, Removing and Installing

Removing and Installing

4.5 Sliding Bar Ball, Installing

4.2 Camshaft, Removing and Installing

4.3 Camshaft Adjustment Valve 1 N205 , Removing and Installing

3.6 Valve Timing, Checking

C3.3 Camshaft Timing Chain, Removing and Installing

n3.2 Overview - Balance Shaft Drive Chain

o2.3 Vibration Damper Sealing Ring, Replacing

m2.2 Timing Chain Cover, Removing and Installing

5.3 Pistons and Cylinder Bore, Checking

r1.5 Compression Pressure, Checking

s1.4 Vacuum Pump, Removing and Installing

1.3 Cylinder Head, Removing and Installing

6 Special Tools

5.2 Pistons, Removing and Installing

1.6 Engine Support, Removing and Installing

4.2 Balance Shaft, Removing and Installing

3.7 Sensor Wheel, Removing and Installing

3.4 Crankshaft Needle Bearing, Replacing

4.3 Balance Shaft Sealing Ring, Replacing, Intake Side

2.3 Sealing Flange, Removing and Installing, Transmission Side

2.2 Flywheel, Removing and Installing

1.5 Auxiliary Components Bracket, Removing and Installing

1.3 Engine, Securing on Engine and Transmission Holder

2.3 Transmission Mount, Removing and Installing

2.6 Subframe Mount, Adjusting

2.7 Subframe Mount, Checking Adjustment

2.2 Engine Mount, Removing and Installing

4 Special Tools

1.2 Engine and Transmission, Separating

1.4 Engine, Installing

Issuu converts static files into: digital portfolios, online yearbooks, online catalogs, digital photo albums and more. Sign up and create your flipbook.