1.6 Oil Level Thermal Sensor G266 , Removing and Installing

Golf 2015 ➤ , Golf Variant 2015 ➤ Engine Mechanical, Fuel Injection and Ignition - Edition 04.2015

1.2 Engine Oil

The oil capacity it determined by attempting. For reasons of tol‐erance, the oil temperature and dripping time cause variance in the actual oil capacity. The performed repair influences the oil capacity. The measurement for the correct oil level is the mark on Protected by copyright . Copying for piva e or commer i al pur po e s , i n p a r t r o r in w ho le, is not permitted unless authorised by Volkswagen AG. Volkswagen AG does notguarantee or accept any liabilit y wi th res pect t o t h e c o r r e c t n e ss o f in format ion in this document. Copyright by Volkswagen AG. the oil dipstick guide tube. Engine oil specification. Refer to the ⇒ Maintenance ; Booklet 36.1 ; Procedure Descriptions; Engine Oil, Capacities and Spec‐ifications . Replacing the engine oil. Refer to ⇒ Maintenance ; Booklet 36.1 ; Procedure Descriptions; Engine Oil, Draining, Replacing Oil Fil‐ter, and Filling . Checking the engine oil level. Refer to ⇒ Maintenance ; Booklet 36.1 ; Procedure Descriptions; Engine Oil Level, Checking . 1.3 Oil Pan Lower Section, Removing and Installing s ⇒ “1.3.1 Oil Pan Lower Section, Removing and Installing, Plastic Oil Pan”, page 182 ⇒ “1.3.2 Oil Pan Lower Section, Removing and Installing, Metal Oil Pan”, page 183 c 1.3.1 Oil Pan Lower Section, Removing and Installing, Plastic Oil Pan t Special tools and workshop equipment required ♦ Used Oil Collection and Extraction Unit - SMN372500♦ Oil Drain Plug Assembly Tool - T10549Caution This procedure contains mandatory replaceable parts. Refer to component overview prior to starting procedure.

Mandatory Replacement Parts ♦ Bolts - Oil Pan

♦ Bolt - Oil Baffle

♦ Gasket - Drain Plug ♦ Oil Baffle

Note

There are plastic ribs on the oil baffle that deform permanently when tightening the oil pan lower section. The plastic ribs ensure the oil baffle has no play and does not rattle. Because of this, always replace the oil baffle.

Golf 2015 ➤ , Golf Variant 2015 ➤ Engine Mechanical, Fuel Injection and Ignition - Edition 04.2015

Removing – Remove the noise insulation -1-. Refer to ⇒ Body Exterior;

Rep. Gr. 66 ; Noise Insulation; Overview - Noise Insulation . – Place the Used Oil Collection and Extraction Unit -

SMN372500- under the engine and drain the engine oil.

Note

Follow all waste disposal regulations!

– Remove the bolts -1 through 20- and remove the oil pan.

– Remove the bolt -1- and remove the oil baffle -2-.

Protectd by copyright . Copying fo pivate or commerci al pur po e s , i n p a r t r o r in w ho le, is not permitted unless authorised by Volkswagen AG. Volkswagen AG does notguarantee or accept any liabilit y wi th res pect t o t h e c o r r e c t n e ss o f in format ion in this document. Copyright by Volkswagen AG. s Installing – Install a new oil baffle. Tightening specification. Refer to -item 7- ⇒ Item 7 (page 180) . – Tighten the new bolts -1 through 20- in two stages in the se‐quence shown: Step Tightening Sequence and Tightening Specification 1. Bolts -1- through -20- Pre-tighten to 8 Nm 2. Bolts -1- through -20- 90° additional turn r – Fill with engine oil and then check the level. Refer to ⇒ Main‐tenance ; Booklet 36.1 ; Engine; Draining; Oil Filter, Replac‐ing; Engine Oil, Filling . e 1.3.2 Oil Pan Lower Section, Removing and Installing, Metal Oil Pan Special tools and workshop equipment required ♦ Used Oil Collection and Extraction Unit - SMN372500-