2 minute read

Torque Chart

The chart below lists the torque values for all the fasteners used on this model transmission. The torque values are also given in the procedures any time a fastener must be tightened. Table Description Torque Value lb·ft Thread Size (Nm) Shift Knob Jam Nut 35–45 (48–61) 1/2” X 13 Shift Lever Housing Capscrews 47–52 (63–70) M10 X 1.5 X30MM Remote Shift Control Mounting Cap- 47–52 (63–70) M10 X 1.5 screws X30MM Clutch Release Yoke Capscrews 35–45 (48–61) 3/8” X 24 Clutch Release Adjusting Arm Cap- 35–45 (48–61) 3/8” X 24 screws Clutch Housing Flange Capscrews See engine manufacturer recommendations for type, size, and assembly torque. Rear Support Studs 60 Minimum (81) M16 X 2.0 Drive until bottomed (When using plugs apply 71206 sealant)

Rear Support Stud Nuts 170-190 (230257) M16 X 1.5

Speed Sensor Retaining Capscrews 20-23 (27-31) M8 X 1.25 PTO Cover Capscrews/Studs 47-52 (63-70) M10 X 1.5 X20MM External Attachment Stud Nuts 20-23 (27-31) M8 X 1.25 Thermocouple Plug 47-52 (63-70) 1/2" NPT Use thread sealant Oil Fill Plug 35-50 (47-67) 1 1/16" X 12 O-ring plug Oil Drain Plug 35-50 (47-67) 1 1/16" X 12 O-ring plug Air System Diagnostic Port Plugs 84-120 lb. in. 1/16"-27 Use thread sealant Oil Level Site Glass 60-70 (81-95) 1 5/8" X 12 O-ring fitting Air Filter/Regulator Capscrews 9-10 (12-14) M6 X 1.0 X 55MM Neutral Switch 15-20 (20-27) M16 X 1.5 O-ring seal Reverse Switch 15-20 (20-27) M16 X 1.5 O-ring seal Splitter Detent Plug 15-20 (20-27) M16 X 1.5 O-ring seal Output Shaft Nut 450-500 (610- M48 X 2.0 Oil at yoke installation 677) Cooler Inlet & Outlet Fittings 40-50 (54-67) 7/8" UNF O-ring fitting Main Case Breather 15-20 (20-27) 1/4" X 18 Use thread sealant

Table Description Torque Value lb·ft (Nm) Thread Size

ECU Breather 84-120 lb-in (9.513.6) 1/8" X 27 Use thread sealant

Clutch Housing / Front Cover Capscrews 47-52 (63-70) M10 X 1.5

Front Bearing Cover Capscrews 35-40 (48-55) M10 X 1.5 X 35MM Front Cover Oil Dam Plate Capscrew 20-23 (27-31) M8 X 1.25 X 12MM Oil Trough Capscrews 20-23 (27-31) M8 X 1.25 X 12MM

Rear Countershaft Bearing CoverCapscrews Output Shaft Bearing Cover Capscrews 47-52 (63-70) M10 X 1.5 X 30MM 47-52 (63-70) M10 X 1.5 X 45MM

Vehicle Wiring Harness Connector Retaining Screw at ECU 7-13 lb-in (.8-1.5) 10 X 24 Part of connector assembly

ECU Mounting Capscrews 20-23 (27-31) M8 X 1.25 X 70MM

ECU Position Sensor Capscrews 22-28 lb-in (2.43.2)

M4 X.75 X 16MM ECU Solenoid Pack Capscrews 22-28 lb-in (2.4- M4 X.75 X 3.2) 16MM Range Piston Retaining Nut 25-35 (34-47) M10 X 1.5 Eccentric Pump Setscrew 3 Maximum (4) M4 X.75 X maximum 25MM Drive until the setscrew bottoms into pump eccentric

Shift Shaft Neutral Detent Plunger Plug 15-20 (20-27) M16 X 1.5

Shift Shaft Reverse Bias Detent Plug 15-20 (20-27) M18 X 1.75 Reverse Idler Retaining Capscrews 47-52 (63-70) M10 X 1.5 X 30MM Cooler Retaining Capscrews 20-23 (27-31) M8 X 1.25 X 12MM

This article is from: