Low coolant indicator 42 Brake pressure indicator

TRAININGMANUAL

PROGRAMMINGTHEINFORMATIONCENTER

NOTE: To enter into the programming modes the key switch must be in the on position.

To get into the programming of the instrument cluster you must perform the following steps: 1 Turn the key switch to the on position, however, do not start the machine. 2 Put the information center into the program mode by pressing the

Program/Reset switch to the left. 3 Press the Up/Down Count switch to the right until the desired Display

Field Number is on the display screen. 4 Push the Program/Reset Switch to the center position. This will display the current value stored in that program location. 5 Push the Up/Down Count switch to the right or left until the desired setting is obtained. 6 Push the Program/Reset switch to the right to store the value in the information center memory. This will also exit you from the programming mode. If you do not wish to change any of the values and only wish to read the information stored in that field display number location you do not need to press the Program/Reset switch to the

Reset position, by going back to the Program position you can move to other display field number locations without starting at location 000. 7 Turn the key switch to the off position. Up count Programme Down count Reset

Display field number and description

Field dnumber Items Status

000 Engine Hoursr 001 Engine Tachometer 002 Speedometer in Miles Per Hour 003 Speedometer in Kilometers Per Hour 004 Engine Coolant Temperature in Degrees Celsius 005 Engine Oil Pressure in Kilopascals 006 Fuel Level in Percent of Fuel Tank 007 Transmission Oil Temperature in Degrees Celsius 008 Hydraulic Oil Temperature in Degrees Celsius 009 Voltmeter Reading (Continuous) 010 Gauge Display Selection 011 Parking Brake Test / Clutch Calibration 012 Information Center Light Setting ñ Work Lights Off. 013 Information Center Light Setting ñ Work Lights On 014 Voltmeter Reading at Key-on 015 Alarm Status 00 = Off 01 = On 016 Coolant Level Status 00 = normal level 01 = low level 017 Brake Pressure Status 00 = Switch closed 01 =Switch opened opened = pressure OK

018 Steering Pressure Status 00 = Switch closed 01 = Switch opened opened = pressure OK 019 Present Park Brake Output from Information Center Status 00 = Off 01 = On

TRAININGMANUAL

PROGRAMMINGTHEINFORMATIONCENTER

Données et champs correspondants

Field Item number Status

020 Present Pilot Lock-out Status Output from Information Center 00 = Off 01 = On 021 Hydraulic Filter Restriction Switch Status. 00 = Closed 01 = Opened ouvert = Filter OK 022 Air Filter Restriction Switch Status. 00 = Switch Closed 01 = Switch opened ouvert = Filter OK 023 Present Work Lights Status 00 = Off 01 = On 024 Present Fog Lights Status 00 = Off 01 = On 025 Air Conditioning High/Low Pressure Switch Status 00 = Switch opened 01 = Switch closed opened= OK 026 Transmission Filter Restriction Switch Status (not fittedon 621C) 00 = switch openedt 01 =switch closed oopened = pres OK 027 Present Status Of High Beam Lights 00 = Off 01 = On 028 Requested Gear Status 101:F1, 102: F2, 103: F3 104:F4, 201: N1, 202: N2 203:N3, 204: N4, 301: R1 302: R2, 303: R3 029 Status of Transmission Operation Indicator In Transmission Display 00 : Always 030 Actual Gear Status 101:F1,102:F2,103:F3 104:F4, 115 = limp home 301:R1, 302:R2,303:R3 315: =limp home

031 Shift status First digit 000: Shift not in process 001:Shift in process

Driveline status second digit 001: Transmission not engaged 010: Transmission engaged

Work mode status(Normal, Substitute tion Limp home) Third digite 010: normal 110: substitution 210: limp home 300:Transmission shut down 400: ECM shut down 032 Hourmeter Status 00 : Always 033 Tachometer Status 00 :Always 034 Current Status of Service Indicator for Normal Operating Mode 00 = Off (Book with the wrench) 01 = On 035 00 : Always 036 Beacon Statusf 00 =: Off 01 = On 037 Left Turn Indicator Status 00 = Off 01 = On 038 Right Turn Indicator Status 00 = Off 01 = On