Stop master indicator (Stop the engine) 44 Caution master indicator

TRAININGMANUAL

PROGRAMMINGTHEINFORMATIONCENTER

Données et champs correspondants

Numéro du champ Donnée Etat du code

039 Current Status Master Indicator (Red) 00 = Off 01 = On

040 Current Status of Diagnostic Indicator 00 – Always (Book without the wrench - Operators Manual) 041 Current Status Master Indicator (Yellow) 00 = Off 01 = On

042 Master Reset 043 Park Brake Switch Status 00 = Switch opened 01 =Switch closed (closed =brake engaged)

044 Redundant Brake Pressure Switch 00 = switch closed Closed = Normal Operation) 01 = switch oened

045 Service Brake Foot Switch Status 00 = switch openedt 01 = switch closed (closed actuated)

046 Pilot Lock-out Switch Status 00 = switch openedt 01 = switch closed (closed =control locked)

047 Spare

050 Minimum Gear SelectionRange Range – 1st or2nd

051 Maximum Gear SelectionRange Range – 2nd, 3irdet 4th

052 Minimum Gear Read Only 053 Maximum Gear Read Only

055 Resettable faults

061 à 070 Service Hour Interval Selection #1 -10

071 à 090 Fault Code #1 Through Fault Code #10 Hour Code #1 Through Hour Code #10. Hour Codes Follow Fault Codes Respectively

091 1st Portion Of Transmission ECM Part Number (ZF) 5 digits from 0 to 9

092 2nd Portion Of Transmission ECM Part Number (ZF) 5 digits from 0 to 9

093 Cluster Software Revision Number 094 Light Emitting Diode (LED) Duty Cycle 095 Liquid Crystal Display (LCD) Duty Cycle

TRAININGMANUAL

PROGRAMMINGTHEINFORMATIONCENTER

Programming the Gauge Display

The C series wheel loaders give the operator the ability to program the instrument cluster to display options that they wish to view. There are five options available in this category. They are as follows:

01Scrolls through Hourmeter, Tachometer, and Speedometer (km/h). 02Scrolls through Hourmeter, Tachometer, and Speedometer (mph). 03Scrolls through Hourmeter (at startup), Tachometer (in 1st ñ 3rd gears), and Speedometer (km/h) (in 4th gear). 04 Scrolls through Hourmeter (at startup), Tachometer (in 1st ñ 3rd gears), and Speedometer (mph) (in 4th gear). 05Scrolls through Hourmeter, Tachometer, and Speedometer (mph), Speedometer (km/h), Engine Coolant

Temperature (Celsius), Engine Oil Pressure (Kpa), Fuel Level, Transmission Oil Temperature (Celsius), Hydraulic

Oil Temperature (Celsius), and Voltmeter.

Two of the options are automatically scrolling displays and three of the options are manual scrolling displays. Options 03 and 04 are automatic scrolling and options 01, 02, and 05 are manual scrolling. In order to advance the display readings during normal machine operation in the manual scrolling mode the operator must hit the Up/Down Count switch in either the up or down position to scroll through the display readings. Pressing the Up/Down Count switch while in the automatic mode will have no effect on the display.

NOTE: 05 is the setting from the factory.

Displaying Individual Functions

It is also possible to see each of the display functions individually at anytime, regardless of the gauge display youíve chosen. The following program locations are available to view at anytime by selecting each display field number one at a time using the programming entry procedure listed previously.

000 Hourmeter 001 Tachometer 002 Speedometer (mph) 003 Speedometer (kph) 004 Engine Coolant Temperature 005 Engine Oil Pressure 006 Fuel Level 007 Transmission Oil Temperature 008 Hydraulic Oil Temperature 009 Voltmeter

When a display option that has a display gauge associated with it is selected the display gauge will flash while the actual value is being displayed on the display screen. Up count Program

Down count Reset

Setting Display Center Light

The operator can set the brightness of the display for two separate conditions. The first is with the work lights off and the second is with the work lights on. To change the brightness of the display for each location select the display field number desired and press the Up/Down Count switch until the desired brightness setting is obtained. The setting can be varied between 001 ñ 100 with 100 being the brightest. The machine is shipped from the factor with a brightness setting of 070 for work lights off and 020 for work lights on. If the display brightness is set to low it may not be possible to read the instrument cluster in bright sunlight.

012 Display brightness for work lights off 013 Display brightness for work lights on