Fuel level gauge 54 Transmission temperature gauge

TRAININGMANUAL

PROGRAMMINGTHEINFORMATIONCENTER

Service Brake Foot Switch Check

This test will check operation of the service brake foot switch to make sure that it is functioning properly. This same check will also shown if the park brake indicator light is functioning.

1Turn the key switch to the on position, do not start the machine. 2Advance to display field number 045 using the programming entry procedure listed previously. The park brake light will flash intermittently. 3Press the Program/Reset switch back to the center position. You should see a 00 in the display if the service brake pedals are not activated. 4Step on the service brake pedal. You should see a 01 in the display when the switch is activated. 5Press the Program/Reset switch to the Reset position to exit the monitoring mode. 6Turn the key switch to the off position.

Pilot Lock-Out Switch Check

This will check operation of the pilot lock-out switch in the cab to make sure that it is functioning properly. This same check will also show if the pilot lock-out indicator light is functioning.

1 Turn the key switch to the on position, do not start the machine. 2 Advance to display field number 046 using the programming entry procedure listed previously. The pilot lock-out light will flash intermittently. 3 Press the Program/Reset switch back to the center position. You should see a 00 in the display if the pilot lockout switch is in the off position. 4 Toggle the pilot lock-out switch to the on position. You should see a 01 in the display when the switch is activated. 5 Press the Program/Reset switch to the Reset position to exit the monitoring mode. 6 Turn the key switch to the off position. Up count Program

Down count Reset

TRAININGMANUAL

PROGRAMMINGTHEINFORMATIONCENTER

Minimum Gear Selection

The 21 ìCî series wheel loaders have the option to start out in either 1st or 2nd gear when operating in the automatic mode. The gear that is selected will be the gear that the transmission is in when the machine begins to move. Machines coming from the factory will be programmed to begin in 1st gear. If the machine is programmed to start in 2nd gear and the load under which the unit is operated becomes too great the machine will automatically down shift to 1st gear.

To change the minimum gear selection: 1Turn the key switch to the on position, do not start the machine. 2Advance to display field number 050 using the programming entry procedure listed previously. 3Press the Program/Reset switch back to the center position. There will be either a 1 or 2 in the display window.

This represents which gear you wish the transmission to start in. 4Press the Up/Down Count switch to the up count position until the desired gear is selected. 5Press the Program/Reset switch to the Reset position hold it for 0.25 seconds to save the desired setting. 6Turn the key switch to the off position.

Maximum Gear Selection

The 21 C series wheel loaders have the option to limit the highest attainable gear when operating in the automatic mode. The lowest gear that can be selected is 2nd gear. Machines coming from the factory will be have the maximum gear set at 4th gear.

To change the maximum gear selection: 1Turn the key switch to the on position, do not start the machine. 2Advance to display field number 051 using the programming entry procedure listed previously. 3Press the Program/Reset switch back to the center position. There will be a 2, 3 or 4 in the display window. This represents the maximum gear currently selected. 4Press the Up/Down Count switch to the up count position until the desired gear is selected. 5Press the Program/Reset switch to the Reset position hold it for 0.25 seconds to save the desired setting. 6Turn the key switch to the off position.

Service Interval Hours

Display field number 061 - 070 are reserved for recording service interval hours. It is up to the customer or operator to assign each location a service item. For example; they may choose to use location 061 to represent engine oil change. Slot 061 will log engine hours independently from the regular engine hour meter reading. The operator can view each field individually to see how many hours have passed since the last engine oil change at any time. When the engine oil is changed the operator can reset slot 061 to 0 hours and it will continue to log engine hours from 0 independently from the regular engine hour meter.

To view the service hour interval locations: 1Turn the key switch to the on position, do not start the machine. 2Advance to display field number 061 - 070 using the programming entry procedure listed previously. 3Press the Program/Reset switch back to the center position. The accumulated hours will show in the display window. 4Press the Program/Reset switch to the Reset position to exit the monitoring mode. 5Turn the key switch to the off position. Up count Program

Down count Reset