RIGHT HAND INSTRUMENT PANEL (Machines Equipped With Automatic Engine Shutdown System) . . . . . . . . . . . . . . . . . . . . . . . . . 49

RIGHT HAND INSTRUMENT PANEL (Machines Equipped With Automatic Engine Shutdown System)

8

1

2 3

BD02E001

Display of Stored Information:

The AES panel automatically stores information on the amount of time that the skid steer was operated in excess of the operational limits described previously. In addition, the panel stores the number of times the machine was shutdown by the AES system. The information is available for review by following the procedure described below.

A. Entering the Review Mode:

With the engine stopped and the ignition switch in the OFF position, hold down the Select Button (2). and the Mode Button (3) together. With both buttons depressed, turn the key to the RUN position (the first position when the key switch is turned clockwise). Continue to depress the Select and the Mode Buttons until the Multi-function display (1) displays the following: SHT XX where XX is a number from 1 to 99.

B. Total Shutdowns Since the Last Reset:

Upon entering the Review Mode, all three of the parameter icon lamps will be illuminated. The information displayed first in the Multi-function display (1) is the total number of machine shutdowns which took place since the last time the panel was reset. This information is displayed in the following format: SHT XX where XX is the number of shutdowns which occurred.

C. Total Time Parameters Were Out of Limits:

To display the combined amount of time all parameters were out of limits, depress the Select Button (2) one time. The information is displayed in the following format: SHT XX:XX where XX:XX is the number of hours and minutes that the skid steer was operated out of limits.

D. Display of Individual Parameters:

To display the number of time an individual parameter has caused the machine to shutdown and the amount of time that parameter was out of limits, depress the Select Button (2) to advance the display. The indicator lamp for the desired parameter will illuminate, and the number of shutdowns due to that parameter will be displayed in the following format: ZZZ XX, where ZZZ is either OIL, WTR, or HYD and XX is the number of shutdowns. To display the amount of time the selected parameter was out of limits, depress the Select Button (2) again. The time will be displayed as follows: ZZZ XX:XX where XX:XX is the time in hours and minutes. Pressing the Select Button (2) a third time will advance the display to the next parameter.

E. Display of Engine Run Hours over Service Limit Interval:

To display the number of hours that the machine has operated past the service interval reminder setting, depress the Select Button (2) until the Service Interval Hourmeter Lamp (8) is illuminated. The display in the multi-function display window (1) will show the following: The Hourglass symbol and XXX, where XXX is the number of hours.

F. Resetting the Parameter Stored Information:

To clear the stored information, with the lamp over the parameter icon to be cleared illuminated and the following displayed in the multi-function display: ZZZ XX:XX (where ZZZ is OIL, WTR, or HYD) depress the Mode Button (3). The lamp over the selected icon will begin to flash and the multi-function display will cycle between the phrase “RESET” and “NO” “YES”. At this point, depressing the Mode Button (3) will clear the information, while depressing the Select Button (2) will cancel the reset operation.

G. Resetting the Service Interval Hourmeter:

To reset the Service Interval Hourmeter, depress the Mode Button (3) until the lamp over the Service Interval icon (8) is illuminated and the display shows: The Hourglass symbol and XXX and then follow the procedure outlined in item F above.

LEFT HAND INSTRUMENT PANEL

The left hand instrument panel monitors the critical functions of the machine and provides information and reminders.

1 2 3

BS96H048

BS96H052

BS96H053 BP96N040

1.Fuel Gauge:

This symbol indicates the fuel level gauge, which is located to the left of the symbol. The gauge consists of a series of lamps that indicate the level of fuel in the fuel tank. When all of the lamps are illuminated the fuel tank is full. When four (4) of the lamps are illuminated the fuel tank is half full. The lamp indicates the following amounts of fuel. Solid Lamp.....................................................15.1litres (4.0 U.S. gals) Flashing Lamp..............................................11.4 litres (3.0 U.S. gals)

2.Engine Oil Pressure Warning Lamp and Alarm:

This lamp will illuminate when the engine is running and the engine oil pressure is too low. The alarm will actuate and the systems normal indicator lamp will go out. Stop the engine and check for the problem.

3.Coolant Temperature Warning Lamp and Alarm:

This lamp illuminates when the engine is running and the engine temperature is too high. The warning alarm will sound and the systems normal lamp will go out. Stop the engine and check for the problem.

LEFT HAND INSTRUMENT PANEL

5

7 4

6

8

BS96H050

BS96H042

BS96H049

BS96H056

BS96H051 BP96N040

4.Hydraulic System Temperature Warning Lamp and Alarm:

When the hydrostatic system temperature becomes too high this lamp will illuminate and the alarm will sound. Stop the engine and check for the problem.

5.Voltage Warning Lamp:

If the battery voltage falls below 11 volts this lamp will illuminate. The system normal lamp will go out.

6.Parking Brake:

This lamp is illuminated when the parking brake is set.

7.Engine Air Filter Warning Lamp:

This lamp will illuminate when the engine air filter becomes restricted and requires servicing. Service immediately.

8.Hydraulic and Hydrostatic Oil Filters Warning Lamp:

If the hydraulic filter becomes restricted, this lamp will illuminate. Service immediately. During cold temperature start up, the warning lamp will stay lit until the hydraulic system reaches operating temperature. If the warning lamp remains lit after operating temperature is achieved, check the hydraulic filter for restriction.