Hsp wood english by HS Protect

H S PRO TECT – W O O D is an air-drying peelable coating designed to protect wooden surfaces from damage during construction, transportation and storage. It can easily be applied with an airless spray gun, paintbrush or paint roller. H S PRO TECT – W O O D protects everyone’s interests! M ore im portantly, H S PRO TECT – W O O D protects your custom er relations! The protective film can be applied to all varnished or painted wood. This can range from wooden joinery, wooden stairs, wooden doors, wooden kitchen and bathroom cabinets to exclusive furniture incorporating glass. The milky color of our product facilitates the application process as it allows the treated surface to remain visible during application. The color of the film will fade as it dries out. H S PRO TECT – W O O D protects all your delicate cabinetwork. It can not only be applied in showrooms, where damaging is reduced to a minimum, but can also be used during transportation or the assembly of furniture on site. Above all, it offers the ultimate protection against all of the nonchalant and uncaring construction workers who disregard the work of others. Start using H S PRO TECT – W O O D and discover this inexpensive and easy-to-use product and its effective results. Are you planning on installing high gloss wood, laminated panels or perhaps wooden structures incorporating stainless steel? H S PRO TECT – W O O D will be your ideal ally. It is suited for both interior and exterior use. Last but not least, it is important to note that H S PRO TECT – WOOD is chemical-free, nonflammable and can be disposed of as regular construction waste. H S PRO TECT – W O O D w ill save you tim e, m oney and a lot of problem s!

Benefits Overview: ü water-based, non-flammable and eco-friendly ü easy to apply/remove and highly cost-effective ü prevents damage ü benefits your customer relations

ü no cleaning needed after removal of the film ü can be disposed of as regular construction waste

Ready in 2 steps: apply and remove

NO MORE BULLSHIT 1

APPLY

REMOVE

TECHNICAL DATA SHEET •

General: H S PRO TECT – WOOD is a revolutionary liquid film that forms a temporary peelable coating when dry. It was developed specifically to protect treated wooden surfaces. The film is weatherproof and UVresistant for up to 12 months outdoors.

•

Application: H S PRO TECT – WOOD protects substrates against weathering, scratches, filthiness (e.g. paint or mortar splashes) and corrosive chemicals that could damage them. Both interior and exterior use is possible. It should not be applied to untreated wood or porous surfaces. It is recommended to perform a test when using acrylic paint.

•

Specifics:

Appearance

Liquid, white (see-through in dry condition)

Fixed Content

Approximately 40%

Density

1.05

Resistance / Durability

H S PRO TECT – WOOD is weatherproof and UV-resistant for a maximum period of 12 months outdoors. It will not detach unless removed by peeling.

Drying time

H S PRO TECT – WOOD will be surface-dry in approximately 30 minutes depending on the weather conditions. It takes 24 hours to completely dry the foil.

Health and safety

Nonflammable in both liquid and dry state. Local Suction: It is recommended to minimize the molar concentration during spray application. The use of protective clothing is advised. Avoid skin and eye contact. In case of: CONTACT WITH EYES: Rinse with water for at least 15 minutes. INHALATION: Inhale fresh air.

CONTACT WITH SKIN: Rinse with water and soap. INGESTION: Remove from stomach by induced vomiting or aspiration. Seek medical attention. RELEASED/SPILLED MATERIAL: Absorb with inert material (e.g. sand, soil, etc.). Caution: Liquid emulsion can be very slippery. WATER DISPOSAL: In accordance with state, local, and federal requirements/measures.

• Application Guidelines Application Temperature

Between 5°C and 35°C = Ideal temperature.

Manual Application

Apply by means of a paint roller. A minimal layer thickness of 200 micron in dry condition, 400 in wet, is recommended. Too thin of a layer will be difficult to remove.

Mechanical Application

Apply by means of a spray gun. Avoid spray-mist edges, so that the overall thickness of the layer is not compromised.

Cleaning

Equipment can be cleaned with warm water. Add detergent if necessary.

Repairs

In case of damage to the H S PRO TECT – WOOD film, the film can easily be replaced by applying a new layer of H S PRO TECT – WOOD above the existing one. The two layers will merge.

Removal

The temporary film H S PRO TECT – WOOD can easily be removed with one move. At temperatures below 5 degrees Celsius, the film may become brittle, which, in turn, will hamper the removal process.

Remarks

The freshly applied H S PRO TECT – WOOD film should be protected against rain for a 24-hour period. Once dry, the H S PRO TECT – WOOD film layer becomes thermoplastic.

•

Transport – Packaging – Storage: Store at room temperature in its closed original packaging. Screen from freezing temperatures. Limit open-air exposure to avoid bacterial growth. Allowed storage: maximum 12 months in non-opened original packaging.

In order to ascertain the suitability of the surfaces to be treated with the

H S PRO TECT products, the application of the

product to a pre-established test area is mandatory. Our company will not be held responsible for damages that may result from erroneous application of the

H S PRO TECT products.