HS protect Metal (english) by HS Protect

H S PRO TECT – M ETAL is an air-drying peelable coating designed to protect metal materials from damage during construction, transportation and storage. It can easily be applied with an airless spray gun, paintbrush or paint roller.

H S PRO TECT – M ETAL protects everyone's interests! H S PRO TECT – M ETAL protects metal by applying a tight film to both ferrous and nonferrous metals. It can also be used on combined metals and is suited for both short and long term protection. H S PRO TECT – M ETAL makes sure metal parts and assemblies or ready for use immediately after removal of the protective foil. No degreasing, scraping or cleaning is needed before using or installing the product. The product does away with problems that may arise due to long exposures to certain weather conditions.

H S PRO TECT – M ETAL protects your customer relations!

Start using H S PRO TECT – M ETAL and discover this inexpensive and easy-to-use product and its effective results.

It is important to note that H S PRO TECT – METAL is chemical-free, non-flammable and can be disposed of as regular construction waste. H S PRO TECT – M ETAL w ill save you tim e, m oney and a lot of problem s!

Benefits Overview: ü water-based, non-flammable and eco-friendly ü multifunctional product offering effective protection ü prevents damages ü easy to use/apply/remove ü replaces ineffective and chemical cleaning products ü time-saving solution

Ready in 2 steps: apply and remove

NO MORE BULLSHIT REMOVE

APPLY

TECHNICAL DATA SHEET •

In General:

H S PRO TECT – M ETAL reduces reparation and reconstruction costs and is easy to apply. It protects substrates against scratches, rust stains and stains caused by acid/corrosive products during application and long-term storage.

•

Field of Application:

H S PRO TECT – M ETAL is revolutionary liquid product that forms a temporary peelable layer. When treating a newly varnished or enameled surface, one should wait until the varnish is completely dry before applying the protective film. When certain parts have been exposed to rain, sun or snow for a longer period of time, it is advised to apply two layers of the H S PRO TECT – M ETAL product. Allow the first layer to dry before applying the second one.

•

Specifics:

Appearance

Liquid, white (see-through in dry condition)

Fixed Content

Approximately 40%

Density

1.05

Resistance / Durability

H S PRO TECT – METAL is weatherproof and UV-resistant for a maximum period of 12 months outdoors. It will not detach unless removed by peeling.

Drying time

H S PRO TECT – METAL will be surface-dry in approximately 30 minutes depending on the weather conditions. It takes 24 hours to completely dry the foil.

Health and safety

Nonflammable in both liquid and dry state. Local Suction: It is recommended to minimize the molar concentration during spray application. The use of protective clothing is advised. Avoid skin and eye contact.

In case of: CONTACT WITH EYES: Rinse with water for at least 15 minutes. INHALATION: Inhale fresh air. CONTACT WITH SKIN: Rinse with water and soap. INGESTION: Remove from stomach by induced vomiting or aspiration. Seek medical attention. RELEASED/SPILLED MATERIAL: Absorb with inert material (e.g. sand, soil, etc.). Caution: Liquid emulsion can be very slippery. WATER DISPOSAL: In accordance with state, local, and federal requirements/measures.

•

Application Guidelines:

Application Temperature

Between 5°C and 35°C = Ideal temperature.

Manual Application

Apply by means of a paint roller. A minimal layer thickness of 200 micron in dry condition, 400 in wet, is recommended. Too thin of a layer will be difficult to remove.

Mechanical Application

Apply by means of a spray gun. Avoid spray-mist edges, so that the overall thickness of the layer is not compromised.

Cleaning

Equipment can be cleaned with warm water. Add detergent if necessary.

Repairs

In case of damage to the H S PRO TECT – METAL film, the film can easily be replaced by applying a new layer of H S PRO TECT – METAL above the existing one. The two layers will merge.

Removal

The temporary film H S PRO TECT – METAL can easily be removed with one move. At temperatures below 5 degrees Celsius, the film may become brittle, which, in turn, will hamper the removal process.

Remarks

The freshly applied H S PRO TECT – METAL film should be protected against rain for a 24-hour period. Once dry, the H S PRO TECT – METAL film layer becomes thermoplastic.

•

Transport – Packaging – Storage: Store at room temperature in its closed original packaging. Screen from freezing temperatures. Limit open-air exposure to avoid bacterial growth. Allowed storage: maximum 12 months in non-opened original packaging.

In order to ascertain the suitability of the surfaces to be treated with the

H S PRO TECT products, the application of the

product to a pre-established test area is mandatory. Our company will not be held responsible for damages that may result from erroneous application of the

H S PRO TECT products.