Model 9600/9700 Swing-Reach ® Lift Truck

Section 6.Electrical Tests

TestI105–Mini Ht Ct [Mini-Mast Height Count] Input Tests

TestI105–Mini Ht Ct [Mini-Mast Height Count]

The mini-mast height count, calculated by the TM, is displayed. The displayed height should increase during lift and decrease during lower.

The mini-mast height count is determined by the height proximity sensor inputs. When the mini-mast is fully lowered, Height Prox A

(“TestI106–Mini Sw A [Mini-Mast Height ProxA]” ), Height Prox B (“TestI107–Mini Sw B [Mini-Mast Height ProxB]” ), and Height Prox C

(“TestI108–Mini Sw C [Mini-Mast Height ProxC]”) are all ON. While lifti ng or lowering, if all three inputs are present at the same time, a fault code occurs. Also, if one of the inputs does not change state while lifting or lowering, a fault code occurs.

Navigate to the input menu and scroll until I06, I07, and I08 are all displayed. Observe the status of each input while lifting or lowering.

If one of the inputs remains ON, it may indicate a shorted mast cable or wiring. If one of the three inputs does not change from ON to OFF while lifting/lowering, refer to the input for the switch that is not changing state.

Publication: 1089040, Issued: 08 Apr 2016 6-111

Section 6.Electrical Tests

Model 9600/9700 Swing-Reach ® Lift Truck Input TestsTestI106–Mini Sw A [Mini-Mast Height ProxA]

TestI106–Mini Sw A [Mini-Mast Height ProxA]

The state of the Prox A channel of the mini-mast height proximity sensor, as seen by the CM, is displayed.

The input is good if these values are displayed:

The value displayed should change as the mini-mast is raised and lowered. If these results are not observed, refer to Diagnosis and Repair.

Diagnosis and Repair

Publication: 1089040, Issued: 08 Apr 2016

Model 9600/9700 Swing-Reach ® Lift Truck

Section 6.Electrical Tests

TestI107–Mini Sw B [Mini-Mast Height ProxB] Input Tests

TestI107–Mini Sw B [Mini-Mast Height ProxB]

The state of the Prox B channel of the mini-mast height proximity sensor, as seen by the CM, is displayed.

The input is good if these values are displayed:

The value displayed should change as the mini-mast is raised and lowered. If these results are not observed, refer to Diagnosis and Repair.

Diagnosis and Repair

Publication: 1089040, Issued: 08 Apr 2016 6-113

Section 6.Electrical Tests

Model 9600/9700 Swing-Reach ® Lift Truck Input TestsTestI108–Mini Sw C [Mini-Mast Height ProxC]

TestI108–Mini Sw C [Mini-Mast Height ProxC]

The state of the Prox C channel of the mini-mast height proximity sensor, as seen by the CM, is displayed.

The input is good if these values are displayed:

The value displayed should change as the mini-mast is raised and lowered. If these results are not observed, refer to Diagnosis and Repair.

Diagnosis and Repair

Publication: 1089040, Issued: 08 Apr 2016

Model 9600/9700 Swing-Reach ® Lift Truck

TestI109–LftSel S6 [Lift Select (S6)] Input Tests

TestI109–LftSel S6 [Lift Select (S6)]

The state of the Lift Select Switch (S6), as seen by the CM, is displayed.

The input is good if these values are displayed:

If these values are not displayed, refer to Diagnosis and Repair.

Diagnosis and Repair

Publication: 1089040, Issued: 08 Apr 2016 6-115

Section 6.Electrical Tests

Model 9600/9700 Swing-Reach ® Lift Truck Input TestsTestI110–Attach S5 [Attachment (S5)]

TestI110–Attach S5 [Attachment (S5)]

The state of the optional Attachment Switch (S5), as seen by the CM, is displayed.

The input is good if these values are displayed:

If these values are not displayed, refer to Diagnosis and Repair.

Diagnosis and Repair

Publication: 1089040, Issued: 08 Apr 2016