Section 3.Systems Overview Model 9600/9700 Swing-Reach ® Lift Truck

enabled, the operator is prompted to enter his/her electronic key when the key switch is turned ON. Truck operation is not allowed unless the correct electronic key or Superword is entered.

Password

Password permits access to Configure Mode only. It is intended for customer use in setting performance parameters within those features purchased with the lift truck.

Superword

Superword permits access to all Program Modes. Superword is intended to limit service access to qualified and trained service technicians.

We strongly recommend that, during installation, you change the Superword from the factory default to a code known only to the Sales and Service Center and/or owner so that access to Diagnostic Mode is limited to qualified personnel. Make sure to record the new Superword in a safe place. If this code is lost or forgotten, a technician must reset the lift truck to factory default settings. This makes it necessary to reconfigure all variable settings.

Run Mode Tones

Tone 1. A single tone that indicates:

•A key on the Operator Keypad (Up/Down/Left/Right/Enter) is pressed

•Maximum steer request is reached

Tone 2. Two tones (high/low) that indicate the TPC and LPC contactors are disabled (opened). Travel, steering, and lift/lower are disabled and the brake is applied until the problem is corrected.

Tone 3. Three tones (high/medium/low) that indicate:

Modes of Operation 3-12

•A travel performance limitation - travel speed is limited to 1 mph (1.6 km/h). Lift, lower, steering, and horn functions operate normally.

•A traction system shutdown - travel is not allowed. Lift, lower, steering, and horn functions operate normally.

•A shutdown in the lift/lower system - lift and lower are not allowed. Travel, horn, and steering functions operate normally.

•Load Handler shutdown

Tone 4. A continuous tone with deadman pedal pressed and Auto/Manual switch in Manual indicates the truck is over the guide wire.

Tone 5. Tone ramps up then repeats, indicating the truck is seeking and aligning over the guide wire. The tone continues until the truck is locked on the guide wire or the Auto/Manual switch is changed to Manual.

Tone 6. Descending tone (bomb drop) that indicates an incorrect Password or Electronic Operator Key was entered.

The tones described do not repeat continuously. A fault code and associated message scroll across the Operator's Display. The message repeats continuously un til the key switch is turned OFF.

Using Program Mode

By entering Prog ram Mode, safety circuits associated with the ACR System are disabled. Follow all instructions in this manual for each test. If you are unsure how to conduct a test while in Program Mode, STOP: do not proceed with the test. Contact an authorized Raymond Sales and Service Center.

To enter Program Mode, use the right button to obtain the cursor prompt. Using the up/down buttons to scroll to the desired number and the left/right buttons to move to a different character position, enter the Password or Superword, then press Enter.

Publication: 1089040, Issued: 08 Apr 2016

Entering Electronic Operator Key, Password, or Superword

An Electronic Operator Key, Password, or Superword can be one to eight characters in length, having any combination of letters, numbers, and/or spaces (indicated by an underscore). A password of all spaces is not permitted.

1.When the password prompt displays, an eight character field of underscores appears. Initially, the left-most character position flashes, showing it is the currently selected position.

2.Use the left/right buttons to select a different character position.

3.Once the character position is selected, use the up/down buttons to select the desired number, letter, or space. The character set wraps between “z” and “_” (space). To go quickly from the letter “z” to the number “0,” press the down button twice.

_0123456789ABCDEFGHIJKLMNOPQR STUVWXYZ

4.Repeat steps 2 and 3 for the remaining Electronic Operator Key, Password, or Superword characters.

5.When all characters in the Electronic Operator Key, Password, or Superword are entered, press the Enter button once.

6.If an invalid Electronic Operator Key, Password, or Superword is entered, a tone sounds and Invalid Password is displayed before returning to the password prompt screen.

7.If a mistake is made entering a character, repeat steps 2 thru 5.

When a correct Electronic Operator Key is entered, the truck completes SelfTest and enters Run Mode.

When the correct Password or Superword is entered, one of the following is displayed for 3 seconds: a.If Password is entered, the following is displayed:

•Quit

•Serial #

•Version

•Hr Meters

•Config b.If Superword is ente red, the following is displayed:

•Quit

•Serial #

•Version

•Hr Meters

•Config

•Learn

•Maint

To exit Program Mode, select Quit and press Enter

Using Configure Mode

Configure Mode can be accessed with Superword or Password, however some items in Config will only appear if Superword is entered.

Table3-1 outlines all menus and submenus available in Config.