Frontier Rotary Tillers RT 1173 RT 1273 RT 2293 RT 1181 RT 2283 Operator's Manual(F07011069) - PDF

O P E R A T O R ’ S

M A N U A L

ROTARY TILLERS RT 1173

RT 1273

RT 1181

RT 2283

RT 2293

RT1173: Serial Number XFRT11X130882 & Above RT1181: Serial Number XFRT11X130879 & Above RT1273: Serial Number XFRT12X130422 & Above

Cod. F07011069 / Rev. 00 (2013-06) THIS MANUAL IS ALSO APPLICABLE TO FRONTIER TILLERS WITH MODEL NUMBERS ENDING IN A ‘C’.

TABLE OF CONTENTS Technical specification Technical specification..................................

Technical specification - Hitch ......................

4 6

Safety signs Safety-Alert simbol .......................................

Identification machine ..................................

Machine safety labels ...................................

7 7 7

Machine safety labels and positions Machine safety labels and positions.............

8

Preparing the vehicle Preparing the tractor ..................................... 10 Park vehicle safety ........................................ 10 Stay clear of rotating drivelines .................... 10

Installing Installing tiller on tractor................................ 10 PTO shaft ..................................................... 12 PTO shaft with clutch ................................... 13 Quick Coupler (optional) ............................... 14 Park vehicle safety ........................................ 14 Stay clear of rotating drivelines .................... 14

Removing Removing tiller .............................................. 15 Removing tiller with Quick Coupler............... 15

Operating Operate safely .............................................. 16 Wear appropriate clothing ............................ 17 Stay clear of rotating drivelines .................... 17 Raising parking stand ................................... 17 Lowering parking stand ................................ 17 Levelling attachments (side-to-side) ............. 17 Levelling tiller (front-to-rear) .......................... 18 Adjusting skid shoes .................................... 18 Adjusting levelling board ............................... 18 Spring ram...................................................... 19

Change speed .............................................. 19 Tilling tips ..................................................... 20 During tilling ................................................. 20 Replacement parts ....................................... 20

Service Machine Safely Practice safe maintenance ........................... 21 Wear appropriate clothing ............................ 21 Stay clear of rotating drivelines .................... 21

Service lubrication Service lubrication ........................................ 22 Every 8 work hours ....................................... 22 Every 50 work hours ..................................... 22 Every 400 work hours ................................... 22 Every 1000 work hours ................................. 22 Greasing and lubricant points....................... 23 Lubricants..................................................... 23 Screw tighteening torques ............................ 23

Service Service intervals ........................................... 24 Replacing tines ............................................. 24 Tines ............................................................. 24

Troubleshooting Using troubleshooting chart ......................... 25

Storing machine Storing tiller .................................................. 26 Removing tiller from storage ......................... 26

Assembly / Spare parts RT 1173-1181....................................................28 RT 2283-2293.................................................30 Lift hook assembly procedure ...................... 32 Installing driveline on tiller ............................ 32 Spare parts ................................................... 32

TO THE DEALER: Assembly and proper installation of this product is the responsibility of the Frontier dealer. Read manual instruction and safety rules. Make sure all items on the Dealer’s Pre-Delivery Check List in the Operator’s Manual are completed before releasing equipment to the owner.

The dealer must complete the Warranty Registration, located on the Frontier website. Warranty claims will be denied if the Warranty Registration has not been completed.

TO THE OWNER: Read this manual before operating your frontier equipment. The information presented will prepare you to do a better and a safer job. Keep this manual handy for ready reference. Require all operators to read this manual carefully and become acquainted with all the adjustment and operating procedures before attempting to operate. Replacement manuals can be obtained from your selling dealer.

The equipment you have purchased has been carefully enginereed and manufactured to provide dependable and satisfactory use. Like all mechanical products, it will require cleaning and upkeep. Lubricate the unit as specified. Observe all safety information in this manual and safety decals on the equipment.

For service, your authorized Frontier dealer has trained mechanics, genuine Frontier service parts, and the necessary tools and equipment to handle all your needs.

Use only genuine Frontier service parts.Substitute parts will void the warranty and may not meet standards required for safe and satisfactory operation. Record the model number and serial number of your equipment in the spaces provided: Model:

Date of Purchase

Serial Number: (see Safety Decal section for location)

Provide this information to your dealer to obtain correct repair parts.

Throghout this manual, the term IMPORTANT is used to indicate that failure to observe can cause damage to equipment. The terms CAUTION, WARNING and DANGER are used in conjunction with the Safety-Alert Symbol, (a triangle with an esclamation mark), to indicate the degree of hazard for items of personal safety.

This Safety-Alert Simbol indicates a hazard and means ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

DANGER

Indicates an imminently hazardous situation that, if not avoided, will result in death or serious injury.

WARNING

Indicates a potentially hazardous situation that, if not avoided, could result in death or serious injury, and includes hazards that are exposed when guards are removed.

CAUTION

Indicates a potentially hazardous situation that, if not avoided, may result in minor or moderate injury.

IMPORTANT NOTE

Indicates that a failure to observe can cause damage to equipment.

Indicates helpful information.

Cod. F07011069 / Rev. 01 (2013-06)

TECHNICAL SPECIFICATIONS

RT 1173 - 1181

RT 1273

RT 2283 - 2293

Technical specifications - Page 4

TECHNICAL SPECIFICATIONS

RT 1173 - 1181 Model

Work/width Tractor HP Tractor HP inches min max

Weight lbs.

Side Drive

PTO shaft

Speeds gear box

Input speed

RT 1173

73

45

60

761

Gear

Slip Clutch

Single

540

RT 1181

81

50

60

810

Gear

Slip Clutch

Single

540

Hitch

Cat. “ II” Quick coupler Cat. “ II” Quick coupler

Tines STD

Rotor blades

Rotor flanges

“ C”

6

10

“ C”

6

11

Tines STD

Rotor blades

Rotor flanges

“ L”

6

7

Tines STD

Rotor blades

Rotor flanges

“ L”

6

8

“ L”

6

9

RT 1273 Model

RT 1273

Work/width Tractor HP Tractor HP inches min max

73

30-70

80

Weight lbs.

Side Drive

PTO shaft

Speeds gear box

Input speed

968

Gear

Slip Clutch

Single

540

Hitch

Cat. “ II” Quick coupler

RT 2283 - 2293 Model

Work/width Tractor HP Tractor HP inches min max

Weight lbs.

Side Drive

PTO shaft

Speeds gear box

Input speed

RT 2283

83

30-70

80

1397

Gear

Slip Clutch

Multi

540

RT 2293

93

40-80

100

1496

Gear

Slip Clutch

Multi

540

Technical specifications - Page 5

Hitch

Cat. ” II” Quick coupler Cat. ” II” Quick coupler

TECHNICAL SPECIFICATIONS - HITCH RT 1173 - 1181: Cat. «I» Standard and iMatch Quick Hitch; Cat. «II» Standard and Quick Coupler Cat. II Std pin Ø mm 25 (inch 0.984) Cat. I Std pin Ø mm 19 (inch 0.748) Cat. II Quick Coupler pin Ø mm 32 (inch 1.26) Cat. I iMatch Quick Hitch Ø mm 32 (inch 1.26)

¯

=

mm m m 823 68 - inc = Without bushings: Cat. «I» Standard 3- h inc 32, Cat. «II» Standard bushings Ø = 28 (inch 1.1) h2 4c Cat. «I» iMatch Quick Hitch bushings Ø = 36,5 (inch 1.44) 6,8 at. ca 2 Cat. «II» Quick Coupler bushings Ø = 36,5 (inch 1.44) t.1

¯

RT 1273 : Cat. «II» Standard and Quick Coupler

Cat. II Std pin Ø mm 25 (inch 0.984) Cat. II Quick Coupler pin Ø mm 32 (inch 1.26)

mm = 82 3

- in ch = 32 ,4

Without bushings: Cat. «II» Standard With bushings: Cat. «II» Quick Coupler

Without bushings: Cat. «II» Standard With bushings: Cat. «II» Quick Coupler ca t. 2

RT 2283 - 2293 : Cat. «II» Standard and Quick Coupler

Cat. II Std pin Ø mm 25 (inch 0.984) Cat. II Quick Coupler pin Ø mm 32 (inch 1.26)

mm = 82 3

Without bushings: Cat. «II» Standard With bushings: Cat. «II» Quick Coupler

- in ch = 32 ,4

Without bushings: Cat. «II» Standard With bushings: Cat. «II» Quick Coupler ca t. 2

Technical specifications - Hitch - Page 6

SAFETY SIGNS Safety-alert symbol Read and recognize safety information.

Be alert to the potential for personal injury when you see this safety-alert symbol.

On your machine safety labels, the words DANGER, WARNING, and CAUTION are used with safety-alert symbol.

DANGER identifies the most serious hazards. In this manual, the word CAUTION and this symbol call attention to safety messages.

Identification machine Identification plate machine

Machine safety labels 1) WARNING: AVOID INJURY FROM ROTATING KNIVES: • Keep hands, feet and clothing away.

2) WARNING: AVOID INJURY FROM PTO: • Keep all shields in place. Keep hands, feet and clothing away.

• Operate only with 540 RPM. 3) CAUTION: AVOID INJURY • Read Operator’s Manual • Ballast power unit per operator’s manual • Know location and function of controls • Keep all shields in place • Stay clear of power driven parts • Never carry riders • Keep people and pets a safe distance away from machine BEFORE DISMOUNTING OR SERVICING • Shut off engine and remove key • Lock brake for park • Lower or block up machine 4) DANGER: ROTATING DRIVELINE - CONTACT CAN CAUSE DEATH - KEEP AWAY! - DO NOT OPERATE WITHOUT: • All driveline, tractor and equipment shields in place • Drivelines securely attached at both ends • Drivelines shields that turn freely on driveline.

5) DANGER: SHIELD MISSING DO NOT OPERATE

Picture Note: Separate telescoping driveshaft members to locate safety label. Label attached to outer profile tube.

Safety Signs - Page 7

MACHINE SAFETY LABELS AND POSITIONS RT 1173 - 1181 3 1

2 1

1 RT 1273

3 1

2

2

1

RT 2283 - 2293

1

3

2 1

3

4 5

4 Safety Signs - Page 8

5

MACHINE SAFETY LABELS AND POSITIONS RT 1173 - 1181

10 8

6

9

MAX Kg...

10 10

6

8 11

9 GREASE

12

7

RT 1273

OIL

10

6

LEVEL

8 9

8

10 10

8

OIL

9 11

9

12

RT 2283 - 2293 6

10

OIL

8

10

9 10

540 MAX

8 9

14

10

11 14

6) 7) 8) 9) 10) 11) 12) 13) 14)

13

12

13

Coupling point for lifting (indicating the maximun capacity) Greasing point / Oil fill and level plugs Oil level plug Oil drain plug Oil fill plug Number of revolutions of power takeoff Warning, slow machine Red strip (only for model: 2293) Amber strip (only for model: 2293)

Safety Signs - Page 9

11

12 13 14

PREPARING THE VEHICLE Preparing the tractor CAUTION: Avoid injury. Proper ballastings is required for safe operation of your tiller IMPORTANT: Refer to the tractor operator manual for proper ballasting information and tire inflation • A 540 rpm PTO • Refer to the tractor operator manual for correct ballasting and tire pressure, depending on installed equipment.

Park vehicle safety • • • • • •

Stop vehicle on a lever surface, not on a slope.

Disengage PTO. Engage the park brake.

STOP the engine.

Remove the key.

Before you leave the operator’s seat, wait for engine and all moving parts to STOP.

Stay clear of rotating drivelines Entanglement in rotating driveline can cause serious injury or death: • Wear close fitting clothing.

• STOP the engine and be sure PTO driveline is stopped before getting near it.

A

Installing tiller on tactor 1. Back tractor into position and align draft links (A) with draft link brackets on tiller using tractor rockshaft control.

CAUTION: Before you work around hitch: • STOP engine.

• LOCK park brake.

• FIRMLY block tiller on horizontal surface.

Locate driller pin in holes (B).

RT 1173 - 1181 model: 2. Insert bushings (D) in each draft links than fasten each draft link to draft link brackets with drilled pins and quiklock pins (C).

For cat. «II» Standard bushings Ø = 28 (inch 1.102) For cat. «II» Quick Coupler bushings Ø = 36,5 (inch 1.437) For cat. «I» iMatch Quick Hitch Ø = 36,5 (inch 1.437) Preparing the vehicle - Page 10

B

A

D

C

INSTALLING Locate driller pin in top lift brackets holes (B).

B

RT 1273 model (Cat. «II» Std.): 2. Fasten each draft link (A) to draft link brackets with drilled pins and quiklock pins (C).

C

Locate driller pin in lower lift brackets holes (E).

A E

RT 1273 model (Cat. «II» Quick Coupler): 2. Insert bushings (D) in each draft links (A) than fasten each draft link to draft link brackets with drilled pins and quiklock pins (C).

D

Locate driller pin in holes (B).

RT 2283-2293 model (Cat. «II» Std.):

B

2. Fasten each draft link (A) to draft link brackets with drilled pins and quiklock pins (C).

C A

RT 2283-2293 model (Cat. «II» Quick Coupler): 2. Insert bushings (D) in each draft links (A) than fasten each draft link to draft link brackets with drilled pins and quiklock pins (C).

D

RT 1273 - 2283 -2293

Locate driller pin in top holes (D) RT 1273-2283-2293 model (Cat. «II» Std.): 3. Install center link (F) on tiller and fasten with drilled pin and quiklock pin (E).

D F

Locate driller pin in top holes (G) RT 1273-2283-2293 model (Cat. «II» Quick Coupler): 3. Install center link (F) on tiller and fasten with drilled pin and quiklock pin (E).

4. Install PTO shaft to tractor.

Installing - Page 11

G

E

INSTALLING IMPORTANT: Tiller MUST BE level front to rear.

• Engage the cardan shaft and check that it is perfectly locked on the tractor PTO (G). Check that the guard (H) is free to turn and fix it with the relative latch.

G

5. Raise tiller.

6. Remove spring locking pin (K) from parking stand.

H

7. Slide parking stand (I) and way up on tiller bracket (J).

8. Fasten with spring locking pin (K).

9. Level tiller (See Leveling Tiller in the Operating Tiller section).

10. Adjust sway chains on tractor lower draft arms to minimize side way.

I

J

PTO shaft The PTO shaft, supplied with the machine, is of standard length.

Therefore it might be necessary to adapt the PTO shaft.

In that case, before doing anything, consult the Manufacturer for the eventual adaptation.

K

A

When the PTO shaft is fully extended, the two tubes must overlap by at least 6 inch (A). When fully inserted, the minimum play must be 1,6 inch (B).

CAUTION: If the implement is used on another tractor, always check that the guards completely cover the rotating parts of the PTO shaft.

Installing - Page 12

B

INSTALLING PTO shaft with clutch The PTO shaft can be equipped with safety clutch to protect the transmission components of the machine from stress and/or excessive overloads.

The tilt of the PTO shaft must not exceed 10 degrees.

The clutch is already pre-adjusted for average stress. If it slips too easily (and overheats), it will be necessary to evenly tighten all the nuts (D) that retain the springs.

The clutch disks must be changed if the clutch still slips after all the nuts have been tightened.

If the clutch does not slip, evenly unscrew all the spring fixing nuts (D). Unscrew one turn at a time and check the clutch after having worked about 300 meters. Repeat the operation if necessary, remembering to unscrew one turn at a time. If the clutch maintains a temperature of about 40-50 (104-122 °F) degrees during work, this means that it has been correctly regulated.

IMPORTANT: Never fully tighten the nuts. This would void the function of the springs and, subsequently, of the clutch, thus damaging the transmission components.

NOTE: This inspection must be performed at the beginning of each new season.

Installing - Page 13

D

INSTALLING Quick Coupler (optional) 1) Install hitch Quick Coupler (A) on the tractor (see tractor operator manual).

B

D

D 2) Stop vehicle on a level surface, not on a slope, then moving back to the tractor until the Quick Coupler (A) is range with the (B) and (C) hitch points.

A C C

3) Raise the Quick Coupler (A) and make sure that tiller’s hitch is in the right position (E).

E

CAUTION: Before you work around hitch: • STOP engine.

• LOCK park brake.

• FIRMLY block tiller on horizontal surface.

Park vehicle safely • • • • • •

Stop vehicle on a level surface, not on a slope.

Disengage PTO. Engage the park brake.

STOP the engine.

Remove the key.

Before you leave the operator’s seat, wait for engine and all moving parts to STOP.

Stay clear of rotating drivelines Entanglement in rotating driveline can cause serious injury or death: • Wear close fitting clothing.

• STOP the engine and be sure PTO driveline is stopped before getting near it.

Installing - Page 14

REMOVING Removing tiller 1. Raise tiller.

2. Put parking stand (A) in the DOWN position: Install spring locking pin (C) in order to secure parking stand (A) to the tiller bracket (B).

3. Lower tiller to the ground.

B

C

A

CAUTION: Before you work around hitch: • STOP engine.

• LOCK park brake.

• FIRMLY block tiller on horizontal surface.

E

4. Disconnect driveline from tractor by pulling back on coupler to release it from the LOCKED position.

5. Remove quik-lock pin (D) and drilled pin (E) from center link (F).

D

F

NOTE: Put quik-lock pins and driller pins back into brackets on tiller for storage.

6. Remove draft links (G) from draft link brackets (H) by removing quiklock pins (I) and drilled pins (L).

NOTE: Put quik-lock pins and driller pins back into brackets on tiller for storage.

7.

Drive tractor forward slowly.

H

L G

Removing tiller with Quick Coupler 1. Raise tiller.

2. Put parking stand (A) in the DOWN position: Install spring locking pin (C) in order to secure parking stand (A) to the tiller bracket (B).

3. Lower tiller to the ground.

4. Raise the two Quick Coupler levers (D) to unloch tiller (Quick Coupler figure, page 14).

5. Lower Quick Coupler till further free the tiller.

Removing - Page 15

I

OPERATING Operate safely • Protect your hands when you inspect or unplug the tiller. You may need gloves or tools, such as a screwdriver or scraper. Be sure hardware is tight. Repair or replace damaged, badly worn, or missing parts. Be sure guards and shields are in good condition and fastened in place. Make any necessary adjustments before you operate.

• Clear work area of objects that you do not want tilled into the ground or that might damage the tiller. Consider the tilling area and set up a safe tilling pattern. Do not till under condition in which traction or stability is doubtful. Keep people and pets out of the work area. Stop machine if anyone enters the area.

• If you hit an object, stop the machine and inspect it.

Make repairs before you operate. Keep machine properly maintained and in good working order.

• DO NOT leave machine unattended when it is running.

• Only operate during daylight or with good artificial light.

• DO NOT let anyone, ESPECIALLY CHILDREN, ride on machine or vehicle. Riders are subject to injury such as being thrown off. Riders may also obstruct the operator’s view, resulting in the machine being operated in an unsafe manner.

• DO NOT let children or an untrained person operate machine.

• DO NOT wear radio or music headphones while operating the machine. Safe operation requires your full attention.

• DO NOT operate the tractor and tiller when you are tired or ill.

It is absolutely forbidden to stand between the tractor and the implement when maneuvering the lift control from the outside.

Operating - Page 16

OPERATING Wear appropriate clothing • Wear close fitting clothing and safely equipment appropriate for the job.

• Loud noise can cause impairment or loss of hearing, wear a suitable protective device such as earplugs.

Stay clear of rotating drivelines Entanglement in rotating driveline can cause serious injury or death: • Wear close fitting clothing • Stop the engine and be sure PTO drivelines is stopped before getting near it.

CAUTION: Before you work around hitch: • STOP engine.

• LOCK park brake.

• FIRMLY block tiller on horizontal surface.

A

Raising parking stand 1. Remove spring locking pin (C).

2. Slide parking stand (A) and way up on tiller bracket (B).

3. Fasten with spring locking pin (C).

B C

Lowering parking stand 1. Remove spring locking pin (C).

2. Slide parking stand (A) and put down on tiller bracket (B).

3. Install spring locking pin in order to secure parking stand to the tiller bracket.

4. Fasten with spring locking pin (C).

C

Leveling attachments (side-to-side) 1. Start the engine. Raise the tiller.

2. Stop the engine. Lock the park brake.

A

CAUTION: DO NOT work under a raised tiller unless it is safely supported.

Operating - Page 17

B

OPERATING Leveling tiller (front-to-rear)

A

1. Start the engine.

2. Lower the tiller to 25 mm (1 in.) off the ground.

3. Stop the engine.

4. Make sure the top of the tiller is LEVEL, or PARALLEL with the ground, front-to-rear.

5. Adjust level, if necessary. To adjust level: a. Start the engine. b. Lower the tiller to the ground. c. Stop the engine. d. Loosen jam nut (A).

• Shorten the center link (B) to lower the front of the tiller.

• Lengthen the center link (B) to raise the front of the tiller. e. Tighten jam nut.

B

D

A

CAUTION: Before you work around hitch: • STOP engine.

• LOCK park brake.

• FIRMLY block tiller on horizontal surface.

B C

Adjusting skid shoes Before adjusting skid shoes lift tiller, place tiller on top of two wooden blocks underneath tiller rotor (see figure).

1. Raise tiller.

2. Place wooden blocks.

3. Lower tiller on wooden blocks.

4. Loosen pivot bolt (A) and (D).

5. Loosen adjusting bolt (B) and lock nut.

6. Adjust skid shoe (C) to desired position.

7. Tighten bolts (A), (B) and (D).

NOTE: Adjust both skid shoes to same depth.

A

6. Repeat above steps for the other skid shoe.

B

Adjusting roller RT 2283-2293 model Mechanical version: to adjust working depth, act on the cranks of the side mechanical hand jacks. (A) Hydraulic version: to adjust working depth, act on the hydraulic distributor of the tractor, connected to the hydraulic jacks. (B)

Mechanical version Hydraulic version

Operating - Page 18

OPERATING Adjusting leveling board 2. Lower leveling board to top of ground (C): • Tilled soil (D) will be fine and level.

• Tractor speed will determine size of clods (E).

3. Raise leveling board (C): • Tilled soil (D) will be coarse and rough.

• Tractor speed will determine size of clods (E).

C B C

Spring Ram (1) Besides supporting the levelling plate and acting as a shock absorber for it during road transport, the spring ram (1) prevents the machine from overturning when parking.

To adjust the spring pre-loading, screw or unscrew the upper nut (2) using the spring adjuster.

The effect of the levelling plate on the soil can be increased or decreased depending on the position, established by the position of the nut (3) in the two holes of the ram (4).

CAUTION: Before you work around hitch: • STOP engine.

• LOCK park brake.

• FIRMLY block tiller on horizontal surface.

Change speed Rotary harrows are equipped with a gearshift with one pair of gears.

A variety of rotation speeds of the rotor can be obtained so that the needs of the operator can be better met.

It is very useful for land which is uneven in that it makes rotary hoeing easy and at the same time allows the tractor to be maintained at a constant speed.

To change tiller speed you must: 1) Unscrew its bolds and remove the rear cover of the gearbox.

CAUTION: Watch out: oil will come out.

2) It is advisable to bend the rotary cultivator forwards.

3) Pull the gears off their shafts and invert the position of their seats.

The name-plate on the cover gives the number of teeth of the gear pair originally installed by the Manufacturer, furthermore, as on page 4 of this handbook, there are the speeds pertainig to the pairs of gears monuted on purchase, plus of the spare pairs.

Each rotary cultivator with gear change has a label which indicates the gear couple mounted as first equipment. The label is attached to the third-point.

Operating - Page 19

E

D

E

2

1 4 3

OPERATING CAUTION: Be very careful and ensure to use the right gears, since some gear pairs cannot be inverted, and gears from different pairs cannot be interchanged. Strictly comply whith the pairs of gears indicated, in the chart on page 4.

Optimum tilling depends on two factors: 1) Forward speed of the tractor.

2) Rotation speed of the blade-carrying rotor.

The faster the rotor rotates, the more chopped up the soil will be.

Tilling tips

Before You till: • Pick up rocks and foreign objects.

• Mow tall weeds and grass to keep them from wrapping around tines or tine shaft.

• Check tines. Loose, bent, broken, or missing tines reduce operating efficiency. If necessary, replace tines.

Test the soil by squeezing it in your hand. If soil forms a ball, it is too wet to till. If soil does not compress easily or falls apart, it is ready to till.

DO NOT till when soil is wet. Wet soil will stick to the tines and tine shaft. Wet soil will also dry out and become hard, making it hard to work with during the growing season.

During tilling CAUTION: Never lower tiller into the ground while the tractor is turning.

• DO NOT back up or make sharp turn with tiller in ground.

• Move PTO switch lever to ON when tiller is out of the ground. Move tractor forward and lower tiller into the ground.

• When you till hard ground or sod, till at a shallow depth on first pass. Increase depth on each pass.

• When tilling on a hillside: - Work up the the slope, if possible.

- If lateral work cannot be avoided, work from the top to the bottom in order to limit any terracing effect.

Replacement parts

See Service Dealer for original parts.

PART NUMBERS MAY CHANGE, use part numbers listed at the end of this manual when you order. If a number changes, your dealer will have the latest number.

WHEN YOU ORDER PARTS, your Frontier Equipment dealer needs your machine serial number. This is the number you have recorded in the INTRODUCTION section in the front of this manual.

Operating - Page 20

SERVICE MACHINE SAFELY Practice safe maintenance • Understand service procedure before doing work. Keep area clean and dry.

• Never lubricate, service, or adjust machine while it is moving. Keep safety devices in place and in working condition. Keep hardware tight.

• To prevent from getting caught, keep hands, feet, clothing, jewelry, and long hair away from any moving parts.

• Before servicing machine, lower it to the ground. Disengage all power and stop the vehicle engine. Lock vehicle park brake and remove the key.

• Securely support any machine elements that must be raised for maintenance.

• Keep all parts in good condition and properly installed. Fix damage immediately. Replace worn or broken parts. Remove any buildup of grease, oil, or debris.

• Unauthorized modifications to the machine may impair its function and safety.

Wear appropriate clothing

• Wear close fitting clothing and safely equipment appropriate for the job.

• Loud noise can cause impairment or loss of earing, wear a suitable protective device such as earplugs.

• Do not wear radio or music headphones while servicing the machine. Safe servicing requires your full attention.

Stay clear of rotating drivelines

Entanglement in rotating driveline can cause serious injury or death: • Stop the engine and be sure PTO drivelines is stopped before getting near it.

Service Machine Safely - Page 21

SERVICE LUBRICATION Service lubrication WARNING: • Firmly block tiller on horizontal surface.

• Always keep oils and greases well away from children’s reach.

• Always thoroughly read the warnings and precautions indicated on the containers. Avoid contact with the skin.

• Always thoroughly and fully wash after use. The utilized oils should be treated in compliance with the current anti-pollution laws.

Every 8 work hours • Grease the cardan shaft cross journals (A) and (B).

• Check that the bolts fixing the hoe blades (I) are well tightened.

• Grease the rotor spindles (D).

Every 50 work hours (see page 23 for E, F, G, I and H)

A

• Check the level of the oil in the gearbox or in the reduction unit (E) and top off to the level mark on the rod as necessary.

• Side transmission gears: check the level of the oil in the side casing of the transmission unit, unscrewing the level plug (G) and checking that oil flows out.

Add oil through the fill plug (F) if necessary. It should flow from the level plug.

B A

C

Every 400 work hours • Change the oil in the reduction unit and transmission casing by completely draining off the old oil through the drain plug under the reduction unit and through the transmission drain plug.(H) • When this operation is carried out, it is also advisable to demount and clean the clutch disks (C) (if the cardan shaft has a clutch). Check the tightening of the clutch springs.

Service Lubrication - Page 22

SERVICE LUBRICATION

E

F

Outer side bearing support

G L

H D

I

Greasing and lubricant points

OIL QUANTITY: lt

D) Rotor spindle lubricator E) Reduction unit oil plug F) Transmission oil fill plug G) Transmission oil level plug H) Transmission oil drain plug I) Hoe blades fixing bolts L) Outer side bearing support fill and level plugs

(US gal.)

1173 1181

1273

Reduction unit oil - E

1(0.25) 1.25(0.3)

Transmission oil fill gears - F

2(0.5)

3 (0.8)

Outer side bear. support - L

0.18 (0.05)

0.18 (0.05)

2283

2293

3(0.8)

4.5(1.2)

4.25 (1.1) 0.18 (0.05)

4.25 (1.1) 0.18 (0.05)

Lubricants

• It is advisable to use SAE 85W/140 OIL or equivalent for the reduction unit (or gear box) and side transmission.

• It is advisable to use GR MU EP 2 GREASE or equivalent for all greasing points.

Bolts tightening torques - settings given in Nm (lb-ft) CLASS

Fine pitch screws 6.6

8.8

10.9

12.9

M8 x 1

15 (11)

26 (19)

36 (26.5)

44 (32.5)

M10 x 1.25 M12 x 1.25 M14 x 1.5 M16 x 1.5 M18 x 1.5 M20 x 1.5 M22 x 1.5 M24 x 2 M27 x 2 M30 x 2

30 (22) 51 (37.5) 81 (60) 120 (88) 173 (127) 242 (178) 321 (237) 411 (303) 601 (443) 832 (614)

52 (38) 91 (67) 143 (105) 214 (158) 308 (227) 431 (318) 571 (421) 731 (539) 1070 (790) 1480 (1090)

74 (54) 127 (94) 201 (148) 301 (222) 433 (319) 606 (447) 803 (592) 1028 (758) 1504 (1110) 2081 (1535)

88 (65) 153 (113) 241 (178) 361 (266) 520 (384) 727 (536) 964 (711) 1234 (910) 1806 (1333) 2498 (1843)

Service Lubrication - Page 23

SERVICE Service intervals

Every 50 working hours: • Tighten mast brackets bolts.

• Tighten skid shoe bolts.

Replacing tines CAUTION: To prevent injuri: Wear heavy gloves when replacing tines.

To get the best performance from your tiller: • Replace badly bent, worn, or broken tines immediatly.

• Replace worn or broken hardware (see your Frontier dealer for correct hardware).

• MAKE SURE to replace tines on ONE spindle at time to keep spiral tine pattern.

• Tine cutting edge MUST BE facing forward in direction of tine rotation.

CAUTION:

Make sure you block tiller before doing any service on the tiller.

• STOP engine. • LOCK park brake. • FIRMLY block tiller on horizontal surface.

Tines can be changed with the tiller mounted on tractor. Make sure you block the tiller before doing any service on the tiller.

Tines

Before replacing tines make sure the tiller is firmly blocked.

The tines with which the rotary tiller is equipped can work soils of normal conformation. Check the degree of wear and condition of the tines each day. If the blades should accidentally bend (or break) during work, they must be immediately replaced.

First - Identify tines: Remember to mount the new tine in exactly the same position as the old one (A). If several tines must be replaced, it is advisable to remove and assemble one tine at a time in order to prevent positioning errors.

The tillers are normally equipped with 4 blades per flange.

Second - Install New Tines: 1. Raise tiller with a safe lifting device.

1. Put safety stands or blocks under tiller.

3. Stand facing rear of tiller and study placement of tines.

4. Remove four bolts, lock washers, and nuts (C).

Service - Page 24

A

C

Front

B

Rear

TROUBLESHOOTING NOTE: Make sure to replace tines on ONE spindle at a time to keep spiral tine pattern.

5. Remove left-hand tine (A) and right-hand tine (B).

6. Install new tines and fasten with bolts, lock washers, and nuts (removed above).

NOTE: Two bolts go in from each side. Refer to sketch at right.

7. Tighten bolts.

CAUTION: The heads of the bolts fixing the hoe blades in place must be on the side of the hoe blades themselves, while the nut with relative washer must be on the flange side (B). Tighten bolts to 91 Nm.

Using troubleshooting chart If you are experiencing a problem that is not listed in this chart, see your Frontier dealer for service.

When you have checked all the possible causes listed and you are still experiencing the problem, see your Frontier dealer.

IF EXCESSIVE TINE WEAR

CHECK Replace loose or bent tine.

Replace tine when worn to a point.

TILLER BUMPING ON GROUND Obstacles entangled in tines.

Blades incorrectly mounted with no tine spiral effect.

Tines fitted with blunt edge leading.

Broken tines.

INSUFFICIENT DEPTH OBTAINED Adjust depth control skids.

Insufficient power - use lower tractor speed.

Gear cover on hard soil - further passes required.

Blades rolling over ground - use lower tractor speed.

Adjust depth control on tractor.

TILLED SOIL TOO FINE Raise leveling board.

Use a faster tractor ground speed.

TILLED SOIL TOO COARSE Lower leveling board.

Use lower tractor speed.

Wait until soil is drier.

TINES BALLING UP WITH SOIL Raise leveling board.

Decrease tractor speed.

Ground too sticky for working.

CUTTING TOO DEEP ON ONE SIDE Tiller not level: • Level tiller.

• Adjust depth control skid.

NOT OVERLAPPING Drive closer to last run.

Start in center and go around clockwise (tilled soil to the right of the operator.)

Troubleshooting - Page 25

STORING MACHINE Storing tiller CAUTION: Before you work around hitch: • STOP engine.

• LOCK park brake.

• FIRMLY block tiller on horizontal surface.

1. Put parking stand in the DOWN position (See Lowering Parking Stand in the Operating Tiller section).

2. Disconnect tiller from tractor (See Removing section).

3. Clean tiller and inside of driveline shield.

4. Repair or replace badly worn or damaged parts.

5. Tighten hardware.

6. Lubricate tiller.

7. Store tiller in a dry place on a hard level surface with the parking stand in the LOWERED position.

8. If you store tiller outside, put a waterproof cover on it.

Removing tiller from storage 1. Install tiller on the tractor.

Storing Machine - Page 26

ASSEMBLY RT 1173 - 1181 CAUTION: FIRMLY block tiller on horizontal surface.

Installing mast braces (PHASE 1) 1) Install spacer (E), bolt (D) and nut (G) on mast braces (A, I) and third point plates (B,F) Do not tighten bolts and nuts at this time.

2) Insert the pin (C) and fix it with the split pin (H).

Installing parking stand (PHASE 2, operation 1) 3) Put parking stand (L) and fasten bolts (M) and nuts (N).

Tighten lock nuts to the requested tightening torque.

Installing draft link brakets (PHASE 2, operation 2) 4) Put each link brackets (O) and (P) on tool bar and fasten bolts and nuts (Q, R).

Do not tighten bolts and nuts at this time.

5) Measure distance between draft, link brackets (O). For the correct measurement of the brackets, centered with gearbox, see the table.

6) Tighten lock bolts (Q) and nuts (R) to secure draft link brackets to tool bar.

• Fine Pitch screws: M16 x 1.5 • Class: 8.8 • Screw tightening torques: 214 Nm (158 lb-ft).

Installing mast braces on tiller (PHASE 2, operation 3) 7) Install mast assembly on tiller frame and tighten. Bolts (S) and nuts (T) to the the requested tightening torque.

• Fine Pitch screws: M12 x 1.25 • Class: 8.8 • Bolts tightening torques: 91 Nm (67 lb-ft).

8) Tighten bolt and nut (D and G) to the requested tightening torque (in Nm): 214.

Assembly - Page 28

ASSEMBLY

D

PHASE 1 E

C

F G

B

H

A

I

PHASE 2 OPERATION 3 OPERATION 2 O

Q

T

P

S

R

M N L OPERATION 1

Assembly - Page 29

ASSEMBLY RT 2283 - 2293 CAUTION: FIRMLY block tiller on horizontal surface.

Installing cage roller -Valid both for mechanical and hydraulic regulations, and for all compa

tible rollers Carry out these operations on both sides of the machine: 1) Fix the upper linkage (A) on both side side panels with the 3 screws M12x1.25x40 (B) and the 3 nuts (C).

2) Fix the connection plates (D) to the roller side panels, with the 3 screws M18X1.5X60 (E) the 3 washers M 19X32X5.3 (F) the 3 nuts M18X1.5 (G) 3) Fix the lower linkage (H) with the 4 screws M14X1.5X50 (I) and the 4 nuts M14X1.5 (J) 4) Remove the two locking stirrups M64400515 (R).

5) Put the two hinge stirrups (K) on the right and left lower linkage (H), replacing the bolt (L) M12X1.25X35 with a new bolt M 12X1.25X40 6) Fix the two hinge stirrups (K) on the transmission and lateral panel, in place of the locking stirrup (R), with the two bolts and the nuts; screw tightening torques 91Nm (68 lib-ft).

7) Fix the mechanical or hydraulic jack (M) into the upper linkage (A), with the pin and split pin (N and O) 8) Install the mechanical or hydraulic jack (M) on the lower linkage (H) with the pin (P) and the split pin (Q).

Assembly - Page 30

ASSEMBLY Mechanical adjustment version

M A

O

N

C M

B

Q

L

F G J

K P

H

I

F

E

D

Hydraulic adjustment version

M A

O

N

C M

B

Q

L

F G J

K P

H

I E

D Assembly - Page 31

ASSEMBLY / SPARE PARTS Lift hook assembly procedure 1. Remove bolts (A) 2. Untighten bolt (B) 3. Rotate lift hook on vertical position (C)

A

B

4. Tighten bolt (A) and bolt (B) to 52 Nm (38 lb-ft) tightening torque.

Installing driveline on tiller NOTE: Shield removed for clarity ONLY. ALWAYS keep shield in place.

C

1. Pull coupler back and slide driveline on driveshaft until coupler LOCKS in place.

NOTE: You should hear a clicking sound when driveline is properly installed.

Spare parts Spare parts should be ordered from your Dealer and should always include the following indications: • Type, model and serial number of the machine.

These data are punched on the data plate with which every implement is equipped.

• Code number of the required spare part. This will be found in the spare parts catalogue.

• Description of the part and required quantity.

• Table number.

• Means of dispatch. If this item is not indicated, the Manufacturer, while dedicating particular care to this service, shall not be held responsible for delays in delivery caused by cases of force majeure.

Transport expenses shall always be at the consignee’s charge. The goods travel at the purchaser’s risk and peril even when sold ex destination.

NOTE: The terms right or left indicated in the descriptions refer to the implement when viewed from the rear side.

Assembly - Page 32

NOTE ................................................................................................................................................................................................................ ............................................................................................................................................................................................................................ ............................................................................................................................................................................................................................ ............................................................................................................................................................................................................................ ............................................................................................................................................................................................................................ ............................................................................................................................................................................................................................ ............................................................................................................................................................................................................................ ............................................................................................................................................................................................................................ ............................................................................................................................................................................................................................ ............................................................................................................................................................................................................................ ............................................................................................................................................................................................................................ ............................................................................................................................................................................................................................ ............................................................................................................................................................................................................................ ............................................................................................................................................................................................................................ ............................................................................................................................................................................................................................ ............................................................................................................................................................................................................................ ............................................................................................................................................................................................................................ ............................................................................................................................................................................................................................ ............................................................................................................................................................................................................................ ............................................................................................................................................................................................................................ ............................................................................................................................................................................................................................ ............................................................................................................................................................................................................................ ............................................................................................................................................................................................................................ ............................................................................................................................................................................................................................ ............................................................................................................................................................................................................................

Part N°. F07011069

P A R T S C A T A L O G

ROTARY TILLERS RT 1173

RT 1273

RT 1181

RT 2283

RT 2293

RT1173: Serial Number XFRT11X130882 & Above RT1181: Serial Number XFRT11X130879 & Above RT1273: Serial Number XFRT12X130422 & Above

Cod. F07010870 / Rev. 00 (2013-06) THIS PARTS CATALOG IS ALSO APPLICABLE TO FRONTIER TILLERS WITH MODEL NUMBERS ENDING IN A ‘C’.

RT 1173 - 1181 - 1273 - 2283 - 2293

PRODUCT IDENTIFICATION AND SERIAL NUMBER PLATE AN INDIVIDUAL PRODUCT IDENTIFICATION AND SERIAL NUMBER IS ASSIGNED TO EACH MACHINE. WHEN WRITING ABOUT OR FILLING OUT WARRANTY CLAIMS, USE ALL THE CHARACTERS SHOWN ON THE PLATE. EXAMPLE: TY0660E002281 TY- FACTORY DESIGNATION (JDM DIVISION) 0660- MODEL OR MACHINE DESIGNATION 0660 - 660 PTO TILLER E- CONFIGURATION CODE 002281- SERIAL NUMBER

PRODUCT CONFIGURATION CODE THE CONFIGURATION «ALPHA» CODE IDENTIFIES A VARIATION OF A PRODUCT. (EXAMPLE: A 116 LAWN FACTOR MAY BE MANUFACTURED AS A HYDROSTATIC OR MANUAL UNIT, AND BE SHIPPED WITH A 970MM OR 70MM MOWER. FOUR VARIATIONS OF THE 116 LAWN TRACTOR EXIST.) IT ALSO IDENTIFIES DIFFERENT PRODUCTS WHICH HAVE THE SAME MODEL OR MACHINE DESIGNATION. EXAMPLE: 216 TRACTOR AND 216 TILLER).

IF NO CONFIGURATION «ALPHA» CODE IS REQUIRED, SPACE IS FILLED IN WITH AN «X».

SERIAL NUMBER LISTING INFORMATION SERIAL NUMBER INFORMATION IS LISTED TO SHOW ON WHICH MACHINES EACH PART CAN BE USED; FOR EXAMPLE:

00000 00000

- 000000 - 000000

THE PART CAN BE USED ON ALL MACHINES. THE PART CAN BE USED ON ALL MACHINES BEGINNING WITH THE SERIAL NUMBER LISTED. THE PART CAN BE USED ON ALL MACHINES UP TO AND INCLUDING THE SERIAL NUMBER LISTED. THE PART CAN BE USED ON ALL MACHINES BETWEEN AND INCLUDING THE SERIAL NUMBERS LISTED.

WHEN XXXXXX’S ARE LISTED IN PLACE OF A SERIAL NUMBER, A SERIAL NUMBER CHANGE WAS MADE, BUT THE EXACT SERIAL NUMBER WAS NOT AVAILABLE WHEN THF CATALOG WAS PRODUCED.

BOX-ENCLOSED ILLUSTRATIONS A KEY NUMBER, SHOWN IN THE PARTS LIST, IS ASSIGNED TO A BOX ENCLOSING ALL PARTS SOLD AS A SERVICE ASSEMBLY.

BOLT AND CAP SCREW STRENGTH IDENTIFICATION BOLTS AND CAP SCREWS REQUIRED TO HAVE HIGH-STRENGTH QUALITIES EQUIVALENT TO SAE GRADE 8 ARE IDENTIFIED THROUGHOUT THIS CATALOG BY THE DESCRIPTION HS SAE 8 (10.9 FOR METRIC). ALL STANDARD BOLTS AND CAP SCREWS ARE SAE GRADE 5 (METRIC 8.8) OR LOWER.

WHOLE GOODS LISTINGS WHOLE GOODS ARE LISTED IN BOLD FACE TYPE. REFER TO LAWN AND GROUNDS CARE SALES MANUAL FOR WHOLE GOODS ORDERING INFORMATION. ORDER SEPARATELY. DO NOT INCLUDE ON REPLACEMENT PARTS ORDER.

DIRECTION ARROW ARROWS ARE USED WITH ILLUSTRATIONS TO INDICATE THE FRONT OF THE UNIT. «RIGHT-HAND» AND «LEFT-HAND» SIDES ARE DETERMINED BY FACING IN THE DIRECTION OF MACHINE FORWARD TRAVEL.

TO THE CUSTOMER THE PART NUMBERS IN THIS PARTS CATALOG WERE CORRECT AT THE TIME THIS CATALOG WAS PUBLISHED. IT IS OUR POLICY TO CONSTANTLY IMPROVE OUR MACHINES; THEREFORE, PART NUMBERS MAY CHANGE WHEN ORDERING PARTS. VERIFY PART NUMBERS THROUGH YOUR DEALER. RT 1173 - 1181 - 1273 - 2283 - 2293 (Jun-13)

RT 1173 - 1181 - 1273 - 2283 - 2293

PRIMARY INDEX FRAME A1 A2 B1 B2 B3 C1 C2 C3

RT 1173 - 1181 RT 1173 - 1181 RT 1273 RT 1273 RT 1273 RT 2283 - 2293 RT 2283 - 2293 RT 2283 - 2293

ROTOR A3 B4 C4

RT 1173 - 1181 RT 1273 RT 2283 - 2293

LATERAL TRANSMISSION A4 B5 C5

RT 1173 - 1181 RT 1273 RT 2283 - 2293

TRANSMISSION A5 B6 C6

RT 1173 - 1181 RT 1273 RT 2283 - 2293

PTO SHAFT A6 B7 C7

RT 1173 - 1181 - 1273 - 2283 - 2293 (Jun-13)

RT 1173 - 1181 RT 1273 RT 2283 - 2293

A1

RT 1173 - 1181

FRAME

45

33 32 29 30 29

42 40 43

26 16 14 13 6

12

31

44 9

28

37 44

34 35

36

41

38

39

4 2 5

46

23 25

6

7

6

24 6 23

27

5

8

3

1 18

9

10

22

11 14 13

47

20 19 6

5 5

6

15 16

6

21

17

3

THIS PARTS LISTING IS CONTINUED RT 1173 - 1181 - 1273 - 2283 - 2293 (Jun-13)

A1 FRAME (CONTINUED)

N.

COD.

DESCRIPTION

1 2 3 4 5 6 7 8 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 22 23 24 25 26 27 28 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 47

5MH10700308 MHF01010291 5MH10700720 5MH10700361 MHF01010288 MHF01220047 5MH10700711 5MH10718500 5MH10720500 MHF01010114 5MH10700610 MHF20100049 MHF20100124 5MH58100930 MHF02200529 5MH37100534 MHF01220070 5MH10700701 MHF01010057 MH01110532 MH63100520 5MH64400515 MH63118538 MH63120538 MHF01010291 5MH10700260 5MH10700261 MHF20100035 MHF01410076 5MH64418510 5MH64420510 5MH10700604 MH40200515 5MH10700620 MHF01010126 MHF20100063 MHF01010053 MHF01010027 5MH10700630 MHF01220034 MHF01010319 MHF01220059 5MH33100599 5MH53400742 5MH26100714 5MH68100647 5MH68100758 MHF01230273 5MH10700590 MH73100912 MH73100911

LEFT SIDE PANEL BOLT M12X1,25X40 U5740 8.8 ZN DOUBLE SKIN RIGHT SIDE PANEL BOLT M 12X1,25X35 SELF LOCKING NUT M12X 1,25 980V EXTERNAL SIDE SKID COMPLETE FRAME RT 1173 COMPLETE FRAME RT 1181 BOLT M 16X1,5X50 COMPL. BAR LINKAGE PIN D.22 L86 BOLT D32 L135 C40 ZN CHAIN SNAP PIN D11 ZGP U BOLT SELF LOCKING NUT M16X 1,5 TRANSMISSION SIDE SKID BOLT M 12X1,25X60 ADJUSTER TOOTHED PLATE SKID ADJUSTER LOCKING STIRRUP HINGE PIN LEVELLING PLATE RT 1173 HINGE PIN LEVELLING PLATE RT 1181 SCREW M12X1,25X40 U5740 8.8 ZG SPACER SUPPORTING STIRRUP STIRRUP BOLT D19 L86 C43 ZN WASHER D12 LEVELLING BONNET RT 1173 LEVELLING BONNET RT 1181 PLATE BUSH 3 POINT DX 3RD POINT BOLT M 16X1,5X110 PIN D25 L91 BOLT M 12X1,25X45 BOLT M 10X1,25X45 SX 3RD POINT NUT M 10X1,25 BOLT M 14X1,5X45 NUT M 14X1,5 SPACER REGULATION TUBE ARTICULATION RAM SUPPORT SPRING NUT M 24X3 LEVELLING TUBE JACK BUSHING D=28 (IN. D=22.5) BUSHING D=36.5 (IN. D=22.5)

RT 1173 - 1181 - 1273 - 2283 - 2293 (Jun-13)

RT 1173 - 1181

A2

RT 1173 - 1181

FRAME

1 2 3 7 4

6 5

SAFETY DECALS KIT

8

FRENCH KIT THIS PARTS LISTING IS CONTINUED RT 1173 - 1181 - 1273 - 2283 - 2293 (Jun-13)

A2 FRAME (CONTINUED)

N.

COD.

DESCRIPTION

1 2 3 4 5 6 7 8

MHF01220047 MHF05100025 MH66100556 MHF02200562 5MH73100715 MHF01010283 MHF20020381 MHF20020376

NUT M12X1,25 D980 8 ZN PLUG SUPPORT PIN D FEET SUPPORTING ROTARY CULTIV. BOLT M 12X30 SAFETY DECALS KIT FRENCH KIT

RT 1173 - 1181 - 1273 - 2283 - 2293 (Jun-13)

RT 1173 - 1181

A3

RT 1173 - 1181

ROTOR

24 12

25 22

23

19 21

17

18

15

20 22 OIL QUANTITY gal.

0,047

12 26

5

6 3

1

14 4

9 26

12 13

12

8

2 10

11

7

THIS PARTS LISTING IS CONTINUED RT 1173 - 1181 - 1273 - 2283 - 2293 (Jun-13)

A3 ROTOR (CONTINUED)

N.

COD.

DESCRIPTION

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 16 17 18 19 20 21 22 23 24 25 26

5MH10700423 5MH10700424 MHF01480123 MHF01200073 MHF20110021 MH00567202 MHF04010222 MHF02050471 MHF03010879 5MH10700459 MHF03010758 MHF01480112 MHF01010246 5MH63100461 5MH63100460 5MH63118434 5MH63120434 5MH63100458 5MHF03010861 MHF04010216 MHF01440033 MHF02050146 5MHF03010684 5MH68100413 MHF01010291 MHF03150630 MHF01010250

RIGHT HELICOIDAL BLADE LEFT HELICOIDAL BLADE WASHER M12 ZGP EXTRA P. NUT M12X1,25 U5587 6S ZN BOLT M 12X1,25X35 KIT BOLT 10X1,25X30 10.9 +NUT+GROWER BEARING 6309 SEEGER RING D.100 WATER-PROOF OIL SEAL 5850 BEARING SUPPORT TRANSMISS. SIDE GASKET OR GROWER WASHER D.8 BOLT M10X1,25X25 U5740 10.9DL TRANSMISSION SIDE ROTOR PIN SIDE PANEL ROTOR PIN BLADES HOLDER ROTOR RT1173 BLADES HOLDER ROTOR RT1181 SIDE PANEL ROTOR SUPPORT WATER-PROOF OIL SEAL 0440 BEARING 6307 SPRING WASHER D.35,2X45X1 ELASTIC RING DE 35X 1,5 U7435 GASKET OR COVER BOLT M12X1,25X40 U5740 8.8 ZN OIL OUTLET PLUG 1/2” BOLT M10X1,25X30 U5740 8.8 ZN

RT 1173 - 1181 - 1273 - 2283 - 2293 (Jun-13)

RT 1173 - 1181

A4

RT 1173 - 1181

LATERAL TRANSMISSION

1 2

3

19

4

5

6

20

18

9 7

17

16

10

8

15

9 14

21

8 13

12

13

8

11

RT 1173 - 1181 - 1273 - 2283 - 2293 (Jun-13)

A4 LATERAL TRANSMISSION (CONTINUED)

N.

COD.

DESCRIPTION

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

MHF01220022 5MH71400361 MHF03010504 5MH63100301 MHF01050086 5MH02108218 5MH29100717 5MH26100321 MHF01410051 MHF01020440 5MH63100306 MHF02010122 MHF03150625 5MH02108308 MHF02010133 5MH63100303 MHF03010504 5MH63100302 MHF04100027 5MH10700308 MHF01020445

NUT M8 GEAR HUB GASKET OR GEAR BOLT M 6X1 X 10 U5927 12.9 BR SELF LOCKING NUT M35X1,5 OIL BREATHER PLUG GASKET WASHER D.8,4 BOLT M8X1,25X25 GEARDRIVE COVER SELF LOCKING NUT M35X1,5 OIL IN/OUT CAP M18X1,5 GASKET SELF LOCKING NUT M40X1,5 GEAR Z=30 GASKET OR GEAR Z=35 BEARING SET TRANSMISSION SIDE PANEL BOLT M 8X30

RT 1173 - 1181 - 1273 - 2283 - 2293 (Jun-13)

RT 1173 - 1181

A5

RT 1173 - 1181

TRANSMISSION

31

17

18

4 1

15 33

16

4 14 33 34 36 35

13 11

19

10

9

12 20

26 29

28

25

24

23

22

21

27 8

32

30 7

6

2

5 4 3 17

THIS PARTS LISTING IS CONTINUED RT 1173 - 1181 - 1273 - 2283 - 2293 (Jun-13)

A5 TRANSMISSION (CONTINUED)

N.

COD.

DESCRIPTION

1 2 3 4 5 5 6 7 8 8 9 9 9 9 10 11 12 13 14 15 16 17 18 18 19 20 21 22 23 23 23 24 25 26 27 28 29 30 31 32 33 34 35 36

MHF01010291 5MHF03010684 MHF04050017 MHF01220047 5MH10718280 5MH10720280 MHF01010249 MHF01480112 MH63118209 MH63120209 5MH10700136 5MH10700137 5MH10700138 5MH10700139 MHF03010305 MHF04050019 MHF02010122 MHF03150630 MHF01480123 MH02108125 5MH10700110 MHF01030122 5MH10718290 5MH10720290 MHF04050076 MH63100102 MHF04050014 MHF03010080 MH09200124 MH09200123 MH09200122 MH09200121 MHF01480099 MHF01020440 MH37100106 MHF01020403 MHF01410051 MH01110144 MH10700107 MH38100146 MHF01410076 5MH10700263 MHF01010288 5MH10700507

BOLT M12X1,25X40 U5740 8.8 ZN GASKET BEARING 30208 SELF LOCKING NUT M12X1,25 980V LEFT SPACER RT 1173 LEFT SPACER RT 1181 BOLT M10X1,25X30 U5740 8.8 ZB GROWER WASHER D.8 TRANSMISSION SHAFT RT 1173 TRANSMISSION SHAFT RT 1181 GASKET MM.0,05 GASKET MM.0,1 GASKET MM.0,3 GASKET MM.0,5 OIL SEAL 50X65X8 BEARING 30210 SELF LOCKING NUT M35X1,5 T.4H ZN OIL OUTLET PLUG 1/2” GROWER WASHER D.12 BREATHER PLUG 1/2 GAS GEARBOX BOLT M12X1,25X 40 U5740 10.9 Z OUTER SPACER RT 1173 OUTER SPACER RT 1181 BEARING 32009 BEVEL GEAR PAIR BEARING 30207 OIL SEAL 35X47X7 GASKET MM.0,15 GASKET MM.0,3 GASKET MM.0,5 COVER P.D.F. PLANE WASHER D.6 BOLT M8X1,25X25 PROTECTION SUPPORT BOLT M 6X16 PLANE WASHER D.8 CARDAN PROTECTION REDUCER UNIT H3 P.T.O. PROTECTION WASHER 12 13X 24X2,5 U6592 ZN BRACKET BOLT M12X1,25X35 U5740 8.8 ZN PLATE

RT 1173 - 1181 - 1273 - 2283 - 2293 (Jun-13)

RT 1173 - 1181

A6

RT 1173 - 1181

PTO SHAFT

6 A

L

5MHF08011789 BONDIOLI

L= 770 6

RT 1173 RT 1181

2 5

4

3 2

L

6 1

15

12 10

7

8

9

10 11

13

14 7

6

THIS PARTS LISTING IS CONTINUED RT 1173 - 1181 - 1273 - 2283 - 2293 (Jun-13)

A6 PTO SHAFT (CONTINUED)

N.

COD.

DESCRIPTION

A 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

5MHF08011789 5MHF08011924 5MHF08011925 5MHF08011922 5MHF08012004 5MHF08011923 5MHF08011926 5MHF08011911 5MHF08011929 MHF08001840 MHF08001400 5MHF08011913 5MHF08011910 5MHF08011906 5MHF08011907 5MHF08011908

UNIVERSAL P T O SHAFT LINKAGE FORK SPIDER ASSY FORK WITH EXTERNAL PIPE PTO SHAFT PROTECTION FORK WITH INTERNAL PIPE CLUCTCH ASSY BOLT M10X085+NUT FLANGE FORK BUSH LINING SPLINED HUB PUSHBUTTON ASSY INNER PLATE PRESSURE SPRING PRESSURE PLATE

RT 1173 - 1181 - 1273 - 2283 - 2293 (Jun-13)

RT 1173 - 1181

B1

RT 1273

FRAME

24 4 5 23 27

29

28

13

30

4 5

22

2

22 21

13 11

1

3 4 5

20 13 19 13

25

12 7

9 10

18

17 16

11 11

15

6 13 8

26

13

14

THIS PARTS LISTING IS CONTINUED RT 1173 - 1181 - 1273 - 2283 - 2293 (Jun-13)

B1 FRAME (CONTINUED)

N.

COD.

DESCRIPTION

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 27 28 29 30

5MH59418500 5MH59400560 5MH59400902 MHF02200529 MH63112581 MH68100932 5MH59400595 MHF20100078 MH37100534 MHF01220070 MHF01010283 MHF01010114 MHF01220059 5MH59400903 MHF01010057 MH01110532 5MH64400520 MH64400515 MHF01010055 5MH10700260 5MH10700261 MHF01010288 5MH20400569 MHF01010210 MHF01010319 MHF03100172 MHF20100063 5MHF20100124 5MH53400522 MHF01480189 MHF01200377

COMPLETE FRAME RT 1273 EXTERNAL SIDE PANEL EXTERNAL SIDE SKID SPLIT PIN D.11 CHAIN BUSHING D=36.5 (IN. D=28.5) STIRRUP PIN D.28 U BOLT SELF LOCKING NUT M16X1,5 980V BOLT M 12X30 BOLT M 16X1,5X50 SELF LOCKING NUT M14X1,5 CHAIN SIDE SKID BOLT M 12X1,25X60 ADJUSTER TOOTHED PLATE SKID ADJUSTER LOCKING STIRRUP BOLT M 12X1,25X50 SPACER SUPPORTING STIRRUP STIRRUP BOLT M 12X1,25X35 3RD POINT BOLT M24X 2X150 U5738 8.8ZN BOLT M14X1,5X45 GASKET SET PIN D25 L91 C43 ZN PIN D32 L135 C40 ZN 3RD POINT LINK GROWER WASHER D.24 NUT M24X2 U5588 6.8 ZN

RT 1173 - 1181 - 1273 - 2283 - 2293 (Jun-13)

RT 1273

B2

RT 1273

FRAME

3

2

4 20

21

22 19

18

14 14 15 1 12

16 13

5

7

9 - RH

10

6

11

8 - LH

THIS PARTS LISTING IS CONTINUED RT 1173 - 1181 - 1273 - 2283 - 2293 (Jun-13)

B2 FRAME (CONTINUED)

N.

COD.

DESCRIPTION

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22

MH63118538 MHF01220047 MH64400515 MHF01010291 5MH59418700 MHF01010250 MHF01220034 5MH59400731 5MH59400730 MHF01010319 MHF01220059 5MH53400742 5MH68100758 MHF01010027 5MH33100599 5MH26100714 MHF01220034 MHF01220059 MHF01010319 MH72100668 MHF01500034 MHF01230273

HINGE PIN LEVELLING PLATE NUT M12X1,25 D980 8 ZN LOCKING STIRRUP BOLT M12X1,25X40 U5740 8.8 ZN LEVELLING BONNET RT1273 BOLT M10X1,25X30 U5740 8.8 ZB NUT M10X1,25 D980 8 ZB LH LEVELLING BONNET EXTENSION RH LEVELLING BONNET EXTENSION BOLT M14X 1,5X 45 U5740 8.8 ZB NUT M14X 1,5 D980 8 ZB ADJUSTMENT PIPE SPRING BOLT M 10X1,25X45 SPACER UPPER JOINT NUT M10X1,25 D980 8 ZB NUT M14X 1,5 D980 8 ZB BOLT M14X 1,5X 45 U5740 8.8 ZB LINKAGE WASHER 26X39X4 U1749 ZN DADO M24X3 D985 8 ZN

RT 1173 - 1181 - 1273 - 2283 - 2293 (Jun-13)

RT 1273

B3

RT 1273

FRAME

4 5 6

3 2 1

7

SAFETY DECALS KIT

8

FRENCH KIT THIS PARTS LISTING IS CONTINUED RT 1173 - 1181 - 1273 - 2283 - 2293 (Jun-13)

B3 FRAME (CONTINUED)

N.

COD.

DESCRIPTION

1 2 3 4 5 6 7 8

5MH56400922 MH66100556 MHF01010288 MHF01220047 MHF02200562 MHF05100025 MHF20020470 MHF20020490

FEET SUPPORTING ROTARY CULTIV. SUPPORT BOLT M12X1,25X35 U5740 8.8 ZN SELF LOCKING NUT M12X1,25 980V PIN D PLUG SAFETY DECALCS KIT FRENCH KIT

RT 1173 - 1181 - 1273 - 2283 - 2293 (Jun-13)

RT 1273

B4

RT 1273

ROTOR

32

17 31

30

29

28 27 26

25 24

23 22

OIL QUANTITY

21

gal.

0,047

20

14 19 18

17

16 7 8

6 3 4

1

5

14

13

15 12 11 10 9

2

THIS PARTS LISTING IS CONTINUED RT 1173 - 1181 - 1273 - 2283 - 2293 (Jun-13)

B4 ROTOR (CONTINUED)

N.

COD.

DESCRIPTION

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32

MH29100407 MH29100408 MHF20110032 MHF01480134 MHF01200089 MH00567201 5MH68100408 5MH59400471 MHF02010144 MHF02050482 MHF04010226 MHF03010879 MHF01010249 MHF01480112 MHF03010768 MH29100413 MHF01480123 MHF01010283 MHF20110011 MH29118401 MH29100413 5MH59400470 5MH68100409 MHF03010861 MHF04010218 MH02108412 MHF02050168 MHF03010756 MHF03010684 5MH68100413 MHF03150630 MHF01010288

RIGHT SQUARE BLADE RT 1273 LEFT SQUARE BLADE RT 1273 BOLT M 14X1,5X40 GROWER WASHER D.14 NUT M14X1,5 BOLT 14X1.5X40 + NUT + GROWER ROTOR HUB ASSY ROTOR SUPPORT TRANSM. SIDE SELF LOCKING NUT M45X1,5 SEEGER RING D.110 BEARING 6310 OIL SEAL 60X75X8 BOLT M10X1,25X 30 GROWER WASHER D.10 SUPPORT GASKET EXTERIOR DUST COVER GROWER WASHER D.12 BOLT M 12X30 BOLT M 10X1,25X30 BLADES HOLDER ROTOR 180 RT 1273 EXTERIOR DUST COVER ROTOR PIN SIDE PANEL ROTOR SUPPORT SIDE PANEL OIL SEAL 55X80X10 BEARING 6308 SEEGER STIFFENER RING SEEGER RING D.40 GASKET OR GASKET OR COVER OIL OUTLET PLUG 1/2” BOLT M 12X35

RT 1173 - 1181 - 1273 - 2283 - 2293 (Jun-13)

RT 1273

B5

RT 1273

LATERAL TRANSMISSION

1 3 4

2 22

21

20 19 18

5 17

6 7

16

15

9

14

13

8 9 12

10

9

11

10 THIS PARTS LISTING IS CONTINUED RT 1173 - 1181 - 1273 - 2283 - 2293 (Jun-13)

B5 LATERAL TRANSMISSION (CONTINUED)

N.

COD.

DESCRIPTION

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22

MHF01220022 5MH59400572 5MHF02100106 5MH71400361 MH29100317 MH29100308 MHF03010504 MH29100304 MH26100321 MH26100307 MH68100301 MHF02010022 MHF01020440 MHF01410051 MH29100717 MHF02010144 MH29100309 MH29100316 MHF01050086 MH29100307 5MH59400581 MHF03010504

SELF LOCKING NUT M8X1,25 980V TRANSMISSION SIDE PANEL ELASTIC PIN GEAR HUB BEARING SET CENTRAL GEAR Z=37 GASKET OR 028/OR2137 DRIVE COVER GASKET GASKET OIL OUTLET PLUG GEARS COVER SELF LOCKING NUT M35X1,5 BOLT M 8X25 PLANE WASHER D.8 OIL BREATHER PLUG SELF LOCKING NUT M45X1,5 LOWER GEAR Z=34 SELF LOCKING NUT 40X1,5 BOLT M 6X10 UPPER GEAR Z=25 SPACER GASKET OR 34,65X1,78 NBR

RT 1173 - 1181 - 1273 - 2283 - 2293 (Jun-13)

RT 1273

B6

RT 1273

TRANSMISSION

1 2

14

13

25 26 4

28

23

27 24 22

3

20 5

21

6

7

17 16

8 11

29

20 19

12

18 15 13

14

9 10

30

6 35

31

32 3

34

33

THIS PARTS LISTING IS CONTINUED RT 1173 - 1181 - 1273 - 2283 - 2293 (Jun-13)

B6 TRANSMISSION (CONTINUED)

N.

COD.

DESCRIPTION

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 15 15 16 17 18 19 20 21 22 23 24 24 24 24 25 26 27 28 29 30 31 32 33 34 35

5MH59400100 MHF01010288 MHF01220047 5MH59418232 MHF01010283 MHF01410076 MHF03010080 MH37100106 MH01110144 MH38100146 MHF01410037 MHF01020403 MHF01020436 MHF01480099 MH16100206 MH16100205 MH16100204 MHF02010133 5MH59400102 MHF03010175 MHF04050083 MH29100152 MHF03150630 MHF04050020 MH29100105 MH29100106 MH29100107 MH29100108 MH29100109 MH66100114 MHF01480112 MHF01010254 MH20100155 MHF04050014 MH29118206 5MH59418230 MHF04050077 MHF03010702 MHF01010254 MHF01010250

COMPLETE GEAR BOX BOLT M 12X1,25X35 SELF LOCKING NUT M12X1,25 980V OUTER SPACER RT 1273 BOLT M 12X1,25X30 GROWER WASHER D.10 OIL SEAL 35X47X7 PROTECTION SUPPORT CARDAN PROTECTION P.T.O. PROTECTION PLANE WASHER D.6 BOLT M 6X16 BOLT M 8X20 GROWER WASHER D.8 GASKET SUPPORT MM.0,15 GASKET SUPPORT MM.0,3 GASKET SUPPORT MM.0,5 SELF LOCKING NUT M40X1,5 GEARBOX HOUSING OIL SEAL 55X70X8 BEARING 32011 BEVEL GEAR PAIR PTO 1” 3/8 Z=6 OIL OUTLET PLUG 1/2” BEARING 30211 BEARING SUPPORT COVER PINION GASKET MM.0,05 GASKET MM.0,1 GASKET MM.0,3 GASKET MM.0,5 STIRRUP GROWER WASHER D.10 BOLT M 10X1,25X35 BREATHER PLUG BEARING 30207 TRANSMISSION SHAFT 180 RT 1273 SPACER RT 1273 BEARING 32209 GASKET OR 4412 BOLT M 10X1,25X35 BOLT M10X1,25X30 U5740 8.8 ZB

RT 1173 - 1181 - 1273 - 2283 - 2293 (Jun-13)

RT 1273

B7

RT 1273

PTO SHAFT

BONDIOLI 6 A

L

MH F08011796

L= 560

6

RT 1273

6 2 5 4 3 2

1

THIS PARTS LISTING IS CONTINUED RT 1173 - 1181 - 1273 - 2283 - 2293 (Jun-13)

B7 PTO SHAFT (CONTINUED)

N.

COD.

DESCRIPTION

A 1 2 3 4 5 6

MHF08011796 MHF08010167 MHF08010678 MHF08010489 MHF08010834 MHF08000600 MHF08011024

PTO SHAFT BON. LINKAGE FORK SPIDER ASSY FORK WITH EXTERNAL PIPE PROTECTION ASSY FORK WITH INTERNAL PIPE CLUTCH ASSY

RT 1173 - 1181 - 1273 - 2283 - 2293 (Jun-13)

RT 1273

C1

RT 2283 - 2293

FRAME

30 28

29

27 31

25

9 10

3

3 24

32

1 2

6

11 23 26

4

32 22

4

3 21

15

5 3 14

7

2 4

12 8 33

19 16 18

9 10

20

13

3 17 3

THIS PARTS LISTING IS CONTINUED RT 1173 - 1181 - 1273 - 2283 - 2293 (Jun-13)

C1 FRAME (CONTINUED)

N.

COD.

DESCRIPTION

1 2 3 4 5 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 29 30 31 32 33

5MH53400501 MHF01010288 MHF01220047 MHF01010283 5MH53420500 5MH53423500 5MH74100456 5MH53400561 MHF01220081 MHF02200529 5MH58100930 MHF01010291 MHF20100075 MH26100514 MHF01010364 MHF01220059 MHF01010057 5MH74100455 MH66100778 MH01110532 5MH64400520 MHF01010317 5MH53400211 MH37100546 MHF03100170 MHF01200377 MHF20120400 MHF01480189 MHF01010210 5MHF20100124 MHF20100063 5MH20400567 5MH53400523 5MH53400738 5MH53400562

EXTERNAL SIDE PANEL SCREW M12X1,25X35 U5740 8.8 ZN NUT M12X1,25 D980 8 ZN BOLT M 12X1,25X30 COMPLETE FRAME 2283 COMPLETE FRAME 2293 EXTERNAL SIDE SKID STIRRUP SELF LOCKING NUT M18X1,5 980V SNAP PIN D.11 ASSEMBLY CHAIN DMP L=476 SCREW M12X1,25X40 U5740 8.8 ZN PIN FOR BAR LINKAGE U BOLT SCREW M18X1,5X50 U5740 8.8 ZN NUT M14X 1,5 D980 8 ZB SCREW M12X1,25X60 U5738 8.8 ZN TRANSMISSION SIDE SKID LOCKING STIRRUP ADJUSTER TOOTHED PLATE SKID ADJUSTER SCREW M14X1,5X35 U5740 8.8 ZN SPACER SUPPORTING STIRRUP STIRRUP GASKET SET NUT M24X2 U5588 6.8 ZN SHAFT HOOK SUPPORT GROWER WASHER D.24 SCREW M24X 2X150 U5738 8.8ZN PIN D32 L135 C40 ZN PIN D25 L91 C43 ZN 3RD POINT 3RD POINT LINK SIDE EXTENSION PLATE BUSHING

RT 1173 - 1181 - 1273 - 2283 - 2293 (Jun-13)

RT 2283 - 2293

C2

RT 2283 - 2293

FRAME

14 12 21 16

20 19 22 10 18 17 16

23 21 15

24 14 13

12

11

3 2 4 8

7 10

6

8 2

4

7

8

1 5

3 7 9

THIS PARTS LISTING IS CONTINUED RT 1173 - 1181 - 1273 - 2283 - 2293 (Jun-13)

C2 FRAME (CONTINUED)

N.

COD.

DESCRIPTION

1 1 2 3 4 5 5 6 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

MH28120796 MH28123796 5MH64400515 MHF01010288 MHF01220047 5MH53420710 5MH53423710 5MH56420710 5MH56423710 MHF01020476 MHF01220033 5MH53400746 5MH53400745 MHF01010319 MHF01220059 MHF01200165 MHF01410157 5MH53400704 MHF01220034 MHF20120401 MHF01010027 MH33100599 MH68100643 MH24100569 MH72100668 MH26100714 MHF01010244

HINGE PIN LEVELLING PLATE 205 HINGE PIN LEVELLING PLATE 230 LOCKING STIRRUP SCREW M12X1,25X35 U5740 8.8 ZN NUT M12X1,25 D980 8 ZN LEFT LEVELLING BONNET RT2283 LEFT LEVELLING BONNET RT2293 RIGHT LEVELLING BONNET RT2283 LEFT LEVELLING BONNET RT2293 SCREW M10X1,5 X 30 5739 8.8 ZN NUT M10X 1,5 D980 8 ZN LEVELLING BONNET LEFT EXTENSION LEVELLING BONNET RIGHT EXTENSION BOLT M14X 1,5X 45 U5740 8.8 ZB NUT M14X 1,5 D980 8 ZB NUT M24X3 5587 5S ZG WASHER M27 28X50X4 U6592 ZB HAND JACK ADJUSTING PLATE NUT M10X1,25 D980 8 ZB SHAFT HOOK SUPPORT BOLT M 10X1,25X45 SPACER ADJUSTING HANDLE SPRING LINKAGE UPPER JOINT SCREW M10X1,25X25 U5740 8.8 ZN

RT 1173 - 1181 - 1273 - 2283 - 2293 (Jun-13)

RT 2283 - 2293

C3

RT 2283 - 2293

FRAME

5 3 4

6

2 7

1

SAFETY DECALS KIT

8

FRENCH KIT THIS PARTS LISTING IS CONTINUED RT 1173 - 1181 - 1273 - 2283 - 2293 (Jun-13)

C3 FRAME (CONTINUED)

N.

COD.

DESCRIPTION

1 2 3 4 5 6 7 8

5MH56400922 MHF05100025 MH66100556 MHF02200562 MHF01220047 MHF01010283 MHF20020304 MHF20020490

SUPPORT PLUG SUPPORT SPLIT PIN SELF LOCKING NUT M12X1,25 980V BOLT M 12X30 SAFETY DECALCS KIT FRENCH KIT

RT 1173 - 1181 - 1273 - 2283 - 2293 (Jun-13)

RT 2283 - 2293

C4 ROTOR

RT 2283 - 2293

28

2 1

26 27 25

24 23 21 20 17 22 19

18

2

1 2

1

17 16 11

29 5

15 6

13

7

12

14 8

3

9 10

4

THIS PARTS LISTING IS CONTINUED RT 1173 - 1181 - 1273 - 2283 - 2293 (Jun-13)

C4 ROTOR (CONTINUED)

N.

COD.

DESCRIPTION

1 2 3 3 4 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 18 19 20 21 22 23 24 25 26 27 28 29

MHF01480123 MHF20110021 MH01110428 MH66100425 MH01110429 MH66100426 MHF20110032 MHF01480134 MHF01200089 MHF04010229 MHF02050515 MHF02010155 5MHF03010879 MHF01010246 MHF01480112 5MHF03010900 5MH53400404 5MH66100416 MH01110411 MH26120425 MH26123425 5MH53400405 5MH53400403 5MHF03010760 5MHF03010861 MHF04010226 MH01110416 MHF02050203 5MHF03010720 5MH66100433 MHF03150630 MH00567201

WASHER M12 ZGP EXTRA P. BOLT M 12X1,25X35 RIGHT SQUARE BLADE RIGHT HELICOIDAL BLADE TG LEFT SQUARE BLADE LEFT HELICOIDAL BLADE TG BOLT M14X1,5X40 10.9 GROWER 15X26,5X4,5 EX.C70 ZN NUT M14X 1,5 U5581 6S ZB BEARING D60 D130 B31 6312 SEEGER RING D.130 SELF LOCKING NUT M50X1,5 WATER-PROOF OIL SEAL 5850 SCREW M10X1,25X25 U5740 10.9DL GROWER WASHER D.10 GASKET OR TRANSMISSION SIDE BEARING SUPPORT DRIVE SIDE HUB EXTERIOR DUST COVER BLADES HOLDER ROTOR 205 BLADES HOLDER ROTOR 230 EXTERNAL SIDE HUB EXTERNAL SIDE BEARING SUPPORT GASKET OR WATER-PROOF OIL SEAL 0440 BEARING D65 D140 B33 21313 SEEGER STIFFENER RING SEEGER RING D50X2 U7435 C70 GASKET OR COVER OIL OUTLET PLUG 1/2” BOLT 14X1.5X40 + NUT + GROWER

RT 1173 - 1181 - 1273 - 2283 - 2293 (Jun-13)

RT 2283 - 2293

C5

RT 2283 - 2293

LATERAL TRANSMISSION

1

3 4

5

2

2 23 21

25

6

19

24

22 18 17 16

14 15

26 20

8

11 7 8

12

13 11

10

9

7

8

THIS PARTS LISTING IS CONTINUED RT 1173 - 1181 - 1273 - 2283 - 2293 (Jun-13)

C5 LATERAL TRANSMISSION (CONTINUED)

N.

COD.

DESCRIPTION

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26

MHF01220034 MHF01480123 MHF01010052 MHF02010022 MHF01010285 5MH53400502 MH26100307 MH26100321 MHF02010056 MHF01010250 MHF01410064 MHF01010244 MH66100311 MH66100303 MHF02010155 MHF03010576 MH26100996 MH66100302 MH26100214 MH29100717 MHF01050086 MH26100327 MH66100301 MH26100997 MH13100301 MH66100314

SELF LOCKING NUT M10X1,25 980V GROWER WASHER D.12 BOLT M 12X1,25X40 SELF LOCKING NUT M35X1,5 BOLT M 12X1,25X30 TRANSMISSION SIDE PANEL OIL OUTLET PLUG GASKET SELF LOCKING NUT M50X1,5 BOLT M 10X1,25X30 WASHER 10,5X21 BOLT M 10X1,25X25 GEARS COVER LOWER GEAR Z=31 SELF LOCKING NUT M50X1,5 GASKET OR 033 DOWTY SPACER CENTRAL GEAR Z=31 SELF LOCKING NUT OIL BREATHER PLUG BOLT M 6X10 BEARING SET UPPER GEAR Z=23 GEAR HUB GASKET CARTER GASKET

RT 1173 - 1181 - 1273 - 2283 - 2293 (Jun-13)

RT 2283 - 2293

C6

RT 2283 - 2293

TRANSMISSION

30

26

33

23

25

27

21

22

31 29

28

33 32 21

34 35 37

36

20 19 16

38 44

18 2 17

15 14

39

40 41

39

36

13

16 15 43 42 2

3 45

1 3

2

2

3

12 11

4

10

5

9

8

3

6 7

THIS PARTS LISTING IS CONTINUED RT 1173 - 1181 - 1273 - 2283 - 2293 (Jun-13)

C6 TRANSMISSION (CONTINUED)

N.

COD.

DESCRIPTION

1 2 3 4 5 6 7 8 9 10 11 12 12 13 13 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 35 36 37 38 39 40 40 40 40 41 42 43 43 43 43 44 45 45

MH37100106 MHF01480112 MHF01010254 MH10100168 MH38100146 MHF01410037 MHF01020403 MH01110215 MH66100209 MHF04050080 MHF01220034 5MH53420205 5MH53423205 MH01110207 MH01110217 MH01110218 MHF03010319 MHF04050022 MH01110149 MHF01010026 MH66100114 MHF02010144 MH37100101 MHF03150630 MH01110112 MH01110110 MHF01020476 MHF01410064 MH01110104 MH01110113 MH01110111 MH01110107 MH66191111 MH33100103 MHF01480123 MHF01010288 MHF01220047 MH66120201 MH66123201 MH01110108 MHF04050072 MH01110109 MHF04050039 MH01110152 MH01110106 MH01110134 MH01110135 MH66100132 MH01110102 MH01110151 MH01110105 MH01110132 MH01110133 MHF03010110 MH66120206 MH66123206

PROTECTION SUPPORT GROWER WASHER D.10 BOLT M 10X1,25X35 CARDAN PROTECTION P.T.O. PROTECTION PLANE WASHER D.6 SCREW M6X1X16 U5739 8.8 ZN GASKET SPACER BEARING 32210 NUT M10X1,25 D980 8 ZB SPACER RT 2283 SPACER RT 2293 GASKET MM.0,1 GASKET MM.0,3 GASKET MM.0,5 RING T.AS 60X 75X 8 D3760 NBR BEARING D60 D110 T23,75 30212 BEVEL GEAR PAIR BOLT M 10X1,25X40 STIRRUP SELF LOCKING NUT M45X1,5 GEARBOX OIL OUTLET PLUG 1/2” GEAR Z-20 GEAR Z-16 SCREW M10X1,5 X 30 5739 8.8 ZN WASHER M10 10,5X20X2 U6592 ZN GEARBOX COVER GEAR Z-22 GEAR Z-18 3MM GEARBOX COVER-GASKET GEAR BOX ASSEMBLY BREATHER PLUG WASHER M12 ZGP EXTRA P. SCREW M12X1,25X35 U5740 8.8 ZN NUT M12X1,25 D980 8 ZN OUTER SPACER OUTER SPACER BUSH SPACER TRANSMISSION BEARING D40 D80 T24,75 32208 POWER TAKE-OFF SHAFT BEARING D40 D90 T25,25 30308 GASKET MM.0,05 GASKET MM.0,1 GASKET MM.0,3 GASKET MM.0,5 BEARING SUPPORT PINION COVER GASKET MM.0,05 GASKET MM.0,1 GASKET MM.0,3 GASKET MM.0,5 OIL SEAL 40X60X10 TRANSMISSION SHAFT TRANSMISSION SHAFT

RT 1173 - 1181 - 1273 - 2283 - 2293 (Jun-13)

RT 2283 - 2293

MECHANICAL ADJUSTMENT ROLLER RT 2283 - 2293

THIS PARTS LISTING IS CONTINUED RT 1173 - 1181 - 1273 - 2283 - 2293 (Jun-13)

RT 2283 - 2293

MECHANICAL ADJUSTMENT ROLLER (CONTINUED)

N.

COD.

DESCRIPTION

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18

MH53400615 MHF01010151 MHF01480156 MHF01220081 MH53400604 MHF01010082 MHF01220059 MHF20100048 MHF02200529 MHF01010291 MH53400810 MHF01220047 MH53400603 MH26400423 MHF01010281 MH04110193 MH53400542 MHF01010053

ROLLER CONN. PLATE BOLT M18X1,5X60 GROWER WASHER D.18 SELF LOCKING NUT M18X1,5 980V ROLLER CONN. ARM BOLT M 14X1,5X50 NUT M14X 1,5 D980 8 ZB BOLT D22 L48 C40 ZN SNAP PIN D.11 BOLT M12X1,25X40 U5740 8.8 ZN ROLLER HINGE STIRRUP NUT M12X1,25 D980 8 ZN JACK CONN. BRACKET MECHANICAL ADJUSTER BOLT M 12X1,25X25 CARTER PROTECTION COVER EXTERNAL SIDE SKID BOLT M 12X1,25X45

RT 1173 - 1181 - 1273 - 2283 - 2293 (Jun-13)

HYDRAULIC ADJUSTMENT ROLLER RT 2283 - 2293

THIS PARTS LISTING IS CONTINUED RT 1173 - 1181 - 1273 - 2283 - 2293 (Jun-13)

RT 2283 - 2293

HYDRAULIC ADJUSTMENT ROLLER (CONTINUED)

N.

COD.

DESCRIPTION

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26

MH53400615 MHF01010151 MHF01480156 MHF01220081 MH53400604 MHF01010082 MHF01220059 MHF20100048 MHF02200529 MHF01010291 MH53400810 MHF01220047 MH53400603 MH26400416 MHF01020451 MHF03150933 MHF03150992 MHF03100023 MHF03150310 MHF03050233 MHF03151219 MH58100890 MHF01010281 MH04110193 MH53400542 MHF01010053

ROLLER CONN. PLATE BOLT M18X1,5X60 GROWER WASHER D.18 SELF LOCKING NUT M18X1,5 980V ROLLER CONN. ARM BOLT M 14X1,5X50 NUT M14X 1,5 D980 8 ZB BOLT D22 L48 C40 ZN SNAP PIN D.11 BOLT M12X1,25X40 U5740 8.8 ZN ROLLER HINGE STIRRUP NUT M12X1,25 D980 8 ZN JACK CONN. BRACKET HYDRAULIC ADJUSTER BOLT M8X 1.25X45 U5739 8.8 ZN GRILLE DOUBLE SUPPORT WASHER 17X23X1,5 NIPPLE CYL.MALE3/8-1/4 ZN HYDRAUL. TUBE R2AT 1/4” L 2530 MALE T-UNION 1/4 ZN HYDRAULIC TUBE BOLT M 12X1,25X25 CARTER PROTECTION COVER EXTERNAL SIDE SKID BOLT M 12X1,25X45

RT 1173 - 1181 - 1273 - 2283 - 2293 (Jun-13)

C7

RT 2283 - 2293

PTO SHAFT

WALTERSCHEID 6 1

L

MH F08011588

L= 710

X

RT 2283 RT 2293 RT 1208

THIS PARTS LISTING IS CONTINUED RT 1173 - 1181 - 1273 - 2283 - 2293 (Jun-13)

C7 PTO SHAFT (CONTINUED)

N.

COD.

DESCRIPTION

1 2 3 4 5 6

MHF08010459 MHF08010686 MHF08010721 MHF08010893 MHF08010533 5MHF08011352

LINKAGE FORK-1’3/8 Z6 SPIDER ASSY FORK WITH EXTERNAL PIPE PROTECTION ASSY FORK WITH INTERNAL PIPE CLUTCH ASSY

RT 1173 - 1181 - 1273 - 2283 - 2293 (Jun-13)

RT 2283 - 2293