CLAAS Arion 430-410 Diagnosis Repair Manual - PDF DOWNLOAD

08 POWER AND CONTROL OUTPUTS

Technical support Arion 430-410

Diagnostics – 10.2009 publication Reference No.00 1139 729 0

08 Power and control outputs Contents

CONTENTS

08 POWER AND CONTROL OUTPUTS FRONT POWER TAKE-OFF SPECIFIC TORQUES AND SEALING COMPOUNDS ........................................................................................................ 5 MEASUREMENTS AND CHECKS....................................................................................................................................... 6 RESULTS RECORD FORM ................................................................................................................................................. 8

REAR POWER TAKE-OFF MEASUREMENTS AND CHECKS....................................................................................................................................... 9 RESULTS RECORD FORM ............................................................................................................................................... 13

Arion 430-410 – 10.2009 – GB

08 Power and control outputs Contents

Notes

Arion 430-410 – 10.2009 – GB

08 Power and control outputs Front power take-off

Front power take-off Specific torques and sealing compounds

16 ± 4 daN.m (243) 7 ± 0,5 daN.m

2,5 ± 0,4 daN.m (638) (638)

(638)

8,7 daN.m

+ 0,5 0,3 – 0 daN.m 23 ± 4 daN.m

Fig. 1

a2108000

Arion 430-410 – 10.2009 – GB

5

08 Power and control outputs Front power take-off

Measurements and checks Checking low pressure of the front power take-off Test conditions: – Engine running at 2 200 rpm.

– Casing oil temperature at 20°C.

1 HYDRO TESTER

Fig. 2

a2108004

– Fit the pressure sensor of the 00 0178 310 0 kit onto the low pressure connector (1).

– Connect tester Nr.00 0178 310 0 to the pressure sensor.

– Measure the pressure which must be 21 bar.

6

Arion 430-410 – 10.2009 – GB

08 Power and control outputs Front power take-off

Checking pressure of the front power take-off command Test conditions: – Engine running at 2 200 rpm.

– Casing oil temperature at 20°C.

1

HYDRO TESTER

Fig. 3

a2108003

– Fit the pressure sensor of kit No.00 0178 310 0 onto the pressure tap (1).

– Connect tester Nr.00 0178 310 0 to the pressure sensor.

– Actuate the "S113" front power take-off engaging command contact.

– Measure the pressure which must be 21 bar.

Arion 430-410 – 10.2009 – GB

7

08 Power and control outputs Front power take-off

Results record form This sheet may be copied and should be completed for each operation on the tractor. If it has to be returned to the manufacturer's after sales department; the following must be included: Tractor type:............................................................................................................................................................................

The serial number:..................................................................................................................................................................

Total operating hours:.............................................................................................................................................................

Date of operation: ...................................................................................................................................................................

Checking low pressure of the front power take-off Test conditions Oil temperature: 20°C Engine running at 2 200 rpm

Hydraulic status (bar) Nominal pressure

PTO engaged

21

PTO disengaged

21

Recorded pressure

Checking pressure of the front power take-off command Test conditions Oil temperature: 20°C Engine running at 2 200 rpm

Hydraulic status (bar) Nominal pressure

PTO brake engaged

21

PTO brake disengaged

0

8

Arion 430-410 – 10.2009 – GB

Recorded pressure

08 Power and control outputs Rear power take-off

Rear power take-off Measurements and checks Checking supply pressure of the rear PTO clutch Test conditions: – Engine running at 2 200 rpm.

– Transmission oil temperature: 60°C.

9010

HYDRO TESTER

Fig. 4

a2108001

– Fit the pressure sensor of the 00 0178 310 0 kit onto the low pressure connector "9010".

– Connect tester Nr.00 0178 310 0 to the pressure sensor.

– Start the tractor, engine speed at 2 200 rev/min.

– Actuate the on/off contact of the "S114" rear power take-off.

– Pressure must stabilize at 21 bars.

Arion 430-410 – 10.2009 – GB

9

08 Power and control outputs Rear power take-off

Checking pressure of the rear power take-off brake Test conditions: – Engine running at 2 200 rpm.

– Transmission oil temperature: 60°C.

HYDRO TESTER

Fig. 5

a2108002

– Fit the pressure sensor of kit Nr.00 0178 310 0 to a T fitted with hoses on the level of the supply of the power take-off brake.

– Connect tester Nr.00 0178 310 0 to the pressure sensor.

– Actuate the "S173" rear power take-off brake contact.

– Measure the pressure which must be 21 bar.

10

Arion 430-410 – 10.2009 – GB

08 Power and control outputs Rear power take-off

Check the rear power take-off lubrication flow rate Test conditions: – Engine running at 2 200 rpm.

– Transmission oil temperature: 60°C.

1

Fig. 6

323msm1t

– Disconect the hose (1).

– Connect a hose to the lubrication supply to pour oil into a graded container.

– Measure the volume of oil collected in one minute.

The flow should be 3,9 l/min.

Arion 430-410 – 10.2009 – GB

11

08 Power and control outputs Rear power take-off

Checking lubrication pressure of the rear power take-off Test conditions: – Engine running at 2 200 rpm.

– Transmission oil temperature: 60°C.

1

HYDRO TESTER

Fig. 7

323msm1u

– Disconect the hose (1).

– Fit 2 hoses.

– Fit a tee to connect tester No.00 0178 310 0.

The pressure should be 1,8 bar.

12

Arion 430-410 – 10.2009 – GB

08 Power and control outputs Rear power take-off

Results record form This sheet may be copied and should be completed for each operation on the tractor. If it has to be returned to the manufacturer's after sales department; the following must be included: Tractor type:............................................................................................................................................................................

The serial number:..................................................................................................................................................................

Total operating hours:.............................................................................................................................................................

Date of operation: ...................................................................................................................................................................

Checking supply pressure of the rear PTO clutch Hydraulic status (bar)

Test conditions Oil temperature: 60°C Engine running at 2 200 rpm

Nominal pressure

PTO engaged

21

PTO disengaged

0

Recorded pressure

Checking pressure of the rear power take-off brake Hydraulic status (bar)

Test conditions Oil temperature: 60°C Engine running at 2 200 rpm

Nominal pressure

PTO brake engaged

21

PTO brake disengaged

0

Recorded pressure

Check the rear power take-off lubrication flow rate Hydraulic status (l/min)

Test conditions Oil temperature: 60°C

Nominal flow

Engine running at 2 200 rpm

Flow recorded

3,9

Checking lubrication pressure of the rear power take-off Test conditions Oil temperature: 60°C

Hydraulic status (bar) Nominal pressure

Engine running at 2 200 rpm

Recorded pressure

1,8

Arion 430-410 – 10.2009 – GB

13

08 Power and control outputs Rear power take-off

Notes

14

Arion 430-410 – 10.2009 – GB