CAB

CAB

SAFETY CAB

Safety cab with roll-over protection structure (ROPS) and against falling objects (FOPS) safegarding the operator. The cab has two doors which can be open 90° (to be used only to enter the cab) assisted by gas filled cylinders and two hinged side panels, with lock in maximum open position, providing enough ventilation and reducing the inlet of dust. It is amply glazed and provides maximum operator comfort under whatever climatic condition.

WARNING The protection offered by ROPS may be prejudiced by any damage or structural change. Inspect your seat belt periodically for signs of fraying, wear or other weaknesses leading to failure.

Do not climb or leave a machine while it is running. Do not jump off the machine.

Do not climb nor leave the machine while transporting equipment or other materials.

When climbing or leaving the operator's compartment, do not use any control as a grabbing point.

Note – The key provided with the machine is universal, i.e. it operates the cab door locks, the side panels and the engine starting switch.

DOOR

The door is open by the handle indicated in the figure, after opening its locks (incorporated in the handle itself) with the appropriate key.

1850-2M0081

Enter and exit the operator's compartment using the appropriate grab handles and stepping points.

Before climbing the machine, clean and inspect steps and handrails.

Climb and leave the machine facing it. Keep three contact points with steps and handrails.

Note – The three points can be two feet and one hand or two hands and one foot.

1850-2M0099

To open from inside, push handle as indicated in the figure. Lubricate the door hinges through the grease fittings indicated.

D350M0174

1850-2M0102

M

1850-2M0100

To release window, press button P inside and pull the door using handle M.

REAR WINDOW

WARNING If replacement of glass is necessary, be sure to use safety glass as spare. Do not strike the glass to remove it from cab parts. Glass may shatter and cause personal injuries.

Note – Windows must always be kept clean to ensure good visibility.

It is recommended to use specific window cleaners and dust free cloth to avoid scratching the glass and impair transparency.

P

1850-2M0101

CAB LIGHTING

The ceiling lights are located on the top of the cab. Switch M in raised position activates fixed light L, in lowered position it actuates movable light P. In central position both lights are OFF.

L M

P

1850-2M0103

12 VOLT SUPPLEMENTARY RECEPTACLE (On cab only)

Supplementary power receptacle P, located in the rear left part of the cab, can be used to power a refrigerator to be located in the compartment behind the seat or to power a portable phone.

Phone holder (T) to be used to store a portable phone, during battery charging phase as well.

T CAB INSIDE HEATING AND VENTILATION

The climatisation of the cab is provided by actuating the controls located under the top of the cab in front of the operator.

1 2 3 4 5 6 7

AUTO ECOM

1 2 3

STOP

C F

13 12 8 9 10 11

D150-2M076

1. Decrease of inside temperature - 2. Increase of inside temperature - 3. Automatic function - 4. Compressor switch OFF - 5. Re-circle - 6. Outside temperature - 7. Switching OFF - 8. 1st fan speed - 9. 2nd fan speed - 10. 3rd fan speed - 11. Change from °C to °F and viceversa - 12. Established degrees monitor - 13. Cab inside temperature sensor.

Demisting and defrosting

To obtain a fast demisting or defrosting of the front, side and rear windows, proceed as follows: -activate through button 10, the fan at max. speed; -actuate button 2 until max. temperature is obtained.

Open the cab vents directing the air flow toward the windows.

P

D150-2M075

D150-2M077

WIPER

Should visibility be unsatisfactory as a result of faulty wiper blade operation, clean rubber blades using a specific detergent or alcohol. Should faulty operation persist, change the blades. For the front wiper proceed as follows: -tilt out complete arm C from glass; -loosen screws D and remove the blade. If the spray pattern of nozzles S is defective, clean the holes with a needle. If necessary, re-adjust the spray nozzle orientation so that the fluid will strike the windshield uniformly.

C

Note – Always keep windows clean to ensure good visibility. It is recommended to use specific window cleaners and dust free cloth to avoid scratching the glass and impair transparency.

Check and fill as required, the level of the windshield washer fluid in its reservoir, reached by opening the rear left panel in the battery compartment.

D350M0096

To replace the side and rear window blades, proceed as for the front wiper.

D

S

D350M0097 1850-2M0104

Note – Use DP1 detergent diluted with water, in relation to ambient temperatures. A 50/50 mixture of detergent and water is not freezing down to - 10 °C (15 ° F). Below this temperature, use pure windshild washer fluid.