The Teacher - Auto Mechanics teacher Martin Girard holds lessons outside the classroom....

54 54

september 2020 | RPM Magazine

www.rpmmag.com

|

september 2020

55 55

T

here’s no denying that the Fox Body Mustang is one of, if not the most popular platform for drag racing.

Brand loyalties aside, if you stop and think about it for second, few people would dare put a Ford or Mopar engine in a first Gen Camaro, yet we’re starting to see as many LS powered Mustangs as we do Ford powered ones over the past few years. Call it what you will, but the fact is that, pound for pound, the Fox body is hard to beat if you want a lightweight candidate to build into a street or strip car.

Saint-Jean-sur-Richelieu, Quebec’s Martin Girard could be considered a purist with his wild ’91 dragstrip-dedicated build – yes, it’s powered by a small block Ford but, despite being brutally quick, he still jambs through the gears with a 5-speed transmission!

“The story started when I was 17 years old with the purchase of my first Fox Body Mustang. It was a street car with some modifications,” said Girard. It was his first Mustang that, like it did for so many, set the hook and would be the catalyst to Girard continuing on with the Fox Mustang body, and also getting in-

56 56

september 2020 | RPM Magazine

The owner-modified 25.2 cert Chromoly roll cage and chassis work was originally done by Hooken Chassis Race Car in Missouri.

www.rpmmag.com

|

september 2020

57 57

The wicked small block Ford started with a Dart block and bullet proof rotating assembly and boasts Blue Thunder heads reworked

by BES

Two Pro Systems Dominator style 1050 custom nitrous carbs top off the SBF.

58 58

september 2020 | RPM Magazine

TM

Dual Friction Clutches

Powerbond Engine Oil Shark Accumulator PN 23900 Premium Tooth In the event of a sudden engine oil pressure Harmonic Oil Pump drop, stored pressure immediately sends oil Balancers

to the main oiling galleries. When the danger The new gear design is over and the pump is once again primed provides the engine with oil, the oil pressure fills the Accumulator with an where it is ready for the next emergency. improved flow of oil Protect Your Engine without the usual pulsing found in traditional gear pumps. This reduction in the pressure ripple from the pump will also provide benefits to the distributor and camshaft drive. Available for SB Chevrolet.

Ask about one for your next project

The Original Wideband UEGO Air/Fuel Ratio Gauge

Unites accuracy, speed and control with an easy to read, digital LED display and sweeping LED “needle” that changes colors as AFR changes PN 30-4110 from rich to lean.

Engine Main Cap Support Kits For Ford Engines

Avoid blown head gaskets or worse,complete engine failure by replacing the weak link in your diesel engine, the head bolts. ARP Head Studs provide for a greater clamping force and are much stronger than OEM bolts.

PN 21-060 Ford, 289/302, Kit PN 21-062 Ford, 351W, Kit PN 21-066 Ford, 429/460, Kit

PN 230-4201 6. L MC Duramax PN 247-4202 Cummins PN 250-4202 6. L ord Powerstroke

Drive by Wire Throttle Enhancement Device • nstalls in ust minutes • mproves vehicles acceleration.

• Waterproof - rugged design • Plug and play - simple install • Remote adjustment knob included; dial in your exact throttle setting.

• Enhance low and mid-range horsepower; torque and acceleration.

• Reduce turbo lag; eliminate stalling on manual gearbox vehicles.

• Can also be stacked with other tuning products to maximize performance.

Alliston - Ideal Supply . . . . . . . . . . . . . (705) 435-6271 Barrie (North) - Ideal Supply . . . . . . . . (705) 728-5911 Barrie (South) - Ideal Supply . . . . . . . . (705) 726-6161 Bracebridge - Ideal Supply . . . . . . . . (705) 645-2247 Brantford - Misener Motorsports . . . . (519) 757-1200 Collingwood - Ideal Supply . . . . . . . . (705) 445-9311 Exeter - Ideal Supply . . . . . . . . . . . . . . (519) 235-0290 Flesherton - Ideal Supply. . . . . . . . . . (519) 924-1444 Goderich - Ideal Supply. . . . . . . . . . . . (519) 524-8389 Hamilton - A&A Discount . . . . . . . . . . (905) 545-9339 Haliburton - Ideal Supply . . . . . . . . . . (705) 457-2322 Hanover - Ideal Supply . . . . . . . . . . . . (519) 364-2960 Harriston - Ideal Supply . . . . . . . . . . . (519) 338-3441 Huntsville - Ideal Supply. . . . . . . . . . . (705) 789-1818 Keswick - Ideal Supply . . . . . . . . . . . . (905) 476-7721 Kincardine - Ideal Supply. . . . . . . . . . (519) 396-3381 Listowel - Ideal Supply. . . . . . . . . . . . . (519) 291-1213 London - Performance Unlimited . . . . (519) 453-0337

Ask about applications for your vehicle

Diesel Head Stud Kits

Designed to reinforce the alignment of the main caps and counter the limited webbing and weaknesses of stock blocks.

These main cap supports are laser-cut from 1/2" - 5/8" steel and feature CNC-machined mounting holes and rod notches for stroke clearance. Includes hardware.

Drop Steps

Pedalmax

ONTARIO

Featuring a Spheroidal Graphite iron casting which is considered near-steel strength material.

Offering the professional engine rebuilder or shade tree mechanic the highest quality product in the automotive aftermarket!

A performance matched pressure plate & disc combination featuring the patented centrifugal weight system (where applicable) and specialized machining processes to provide a performance clutch that offers exceptional street characteristics, while offering outstanding holdingcapacity and durability.

Notched-bar design provides strong traction and 2” more toe/heel step area than competing steps.

Textured-black finish complements WESTiN’s HDX bumpers. Includes mount kit and installation hardware.

Semi-Synthetic

Racing ATF • Anti-wear, anti-oxidants and corrosion inhibitors • "Sport" or "hard shift" shift character • Resists shear thinning • Holds-up under the heat and stress of racing applications PN 11020 1 US quart

Rebellion XD Ball Mount with

Shock Drop

Adjustable cushion hitch ball mount (2" Shank, 15,000 lbs., 6-1/4" Drop). Dampens jerking and jarring from bumps and potholes for smoother towing.Reduces the tendency PN 45949 for trailer sway.

• Small 3" X 3" body • Hybrid Spot Optic • Powerful LED Technology • Lumens each

D-SERIES

PN 202213 LED Spot - Clear Pair PN 202213BLK LED Spot - Black Pair

PRO SPOT

Multi-Purpose LED Lamps

Midland - Ideal Supply . . . . . . . . . . . . . (705) 526-5488 Thunder Bay - DC Automotive . . . . . (877) 351-5604 Mitchell - Ideal Supply. . . . . . . . . . . . . (519) 348-9639 Walkerton - Ideal Supply . . . . . . . . . . (519) 881-0980 Mt. Forest - Ideal Supply . . . . . . . . . . . (519) 323-1530 Wingham - Ideal Supply . . . . . . . . . . . (519) 357-3830 Newmarket - ZZ Performance . . . . . (888) 572-8867 Woodstock - Ideal Supply . . . . . . . . . (519) 539-7483 New Hamburg - Ideal Supply . . . . . . (519) 662-2411 QUEBEC New Hamburg - Rudy Held's . . . . . . (519) 662-2821 Mirabel - Wizzo Performance . . . (877) 560-9178 Orangeville - Ideal Supply . . . . . . . . . (519) 941-1510 St-Augustin-de-Desmaures Orillia - Ideal Supply . . . . . . . . . . . . . . . (705) 325-1335 - Brossard Performance (418) 872-3376 Oshawa - Karbelt Speed & Custom . . (905) 579-9884 Terrebonne - Para Performance . . . . (450) 492-0141 Owen Sound - Ideal Supply . . . . . . . . (519) 371-0810 NOVA SCOTIA Parry Sound - Ideal Supply . . . . . . . . (705) 746-9564 Truro - R&D Performancenter . . . . . . . (800) 565-3795 Pickering - Karbelt Speed & Custom (905) 839-4421 Port Elgin - Ideal Supply . . . . . . . . . . . (519) 389-4242 Seaforth - Ideal Supply . . . . . . . . . . . . (519) 527-0880 Shelburne - Ideal Supply . . . . . . . . . . (519) 925-6311 For information on becoming a member location contact: Stratford - Ideal Supply. . . . . . . . . . . . (519) 273-0650 USA St. Marys - Ideal Supply . . . . . . . . . . . (519) 284-1090 800•344•0368 59 59 www.rpmmag.com september Canada 2020 Stoney Creek - A&A Discount . . . . . (905) 643-7700 888•527•2358 Sudbury- Witrak Auto Specialties . . . . (705) 566-9870

LIVE LOCAL |

BUY LOCAL

The Teacher in the staging lanes with the teacher, Martin Girard.

I was driving a 10.20 street car with a naturally aspirated 408inch SBF to work every day! volved in drag racing them.

By the time 2000 rolled around Girard would buy another Fox Body that would see street and strip duty. “We started with running 12 seconds in the ¼, then 11 seconds and eventually 10s, all while keeping it a street car,” Girard explained. The one thing that’s a bit different in this story is that Martin nev60 60

september 2020 | RPM Magazine

er swayed from shiftn’ gears, “I’ve always driven manual transmissions in my 20 years of drag racing, I never had an automatic! I like the feeling of driving a fast car and changing the gears myself.”

Just like many of us who have experimented with manual transmissions during the evolution of building a car to go quicker and faster, with each new modification Girard experienced the trials and tribulations of that game, finding the limitations of each transmission along the way.

“That second Mustang had a Tremec transmission but at one point I decided to install a Ford Top Loader 4 speed pro-shifted by Liberty. I was driving a 10.20 street car with a naturally aspirated 408-inch SBF to work every day!”

When daily driving the car became not quite so practical,

[Above] From left to right: Marc-André Fortin, Gabriel Jetté, Martin Girard, Patrick Donnelly and Yves Bourgeois with Martin’s kids William and Kariane.

www.rpmmag.com

|

september 2020

61 61

A carbon fiber one! Mark Williams carbon fiber discs and pads help with the stopping duties out back.

A carbon fiber pro stock style scoop si of a custom cowl hood pulls massive atmosphere in to feed the twin D

moserengineering.com

62 62

september 2020 | RPM Magazine

itting on top amounts of Doms.

the decision was made to convert it to mini tub and cage it. From there, nitrous was added to the street motor along with a GF5R G-Force 5-speed clutchless trans. The results were a 9.27 ET, then, with a few more upgrades and a swap to a G-Force GF 2000 the following year, 8.91s.

By 2008 Girard decided he had reached the limit of the 408 SBF and grabbed an old class engine built to run Hot Street with NMRA; a naturally aspirated 398-inch with 865HP good for 10,000 rpm, and, as always the 5-speed found a home behind it. When the car was completed, however, the unthinkable happened the first time out and Martin crashed, completely destroying the car. “It was a total loss and I got away with just a few minor injuries, thanks to the safety equipment,” Girard said.

This sequence of life events led Martin to the

KINSLER NEW

Patent Pending

TOUGH

®

PUMP

Steady Flow at EXTREME RPM

Excellent Durability

Kinsler.com 248 362-1145 www.rpmmag.com

|

september 2020

63 63

64 64

september 2020 | RPM Magazine

Not one but two nitrous kits, both from Induction Solutions, provide the extra hit needed to take on the turbo crowd in No Time drag racing.

www.rpmmag.com

|

september 2020

65 65

Mustang you see here, a 1991 former Hot Street class car that has been completely overhauled. Carroserie Xtreme took care of the body and paint, a new engine was built by Claude Gauthier and spec’d by Sam Vincent, and, once again it’s a Liberty Extreme clutchless 5-speed trans backing up the sprayed small block Ford.

Body and paint on the car speaks for itself, it’s flawless and kept that way by Girard and his team. The chassis was originally built by Hooken Chassis Race

Car and modified by Martin. Inside, the car is 100% racecar with the exception of the dash, but it is the G-Force trans that screams “hardcore”, that, and the Induction Solutions nitrous bottle.

The 422-inch small block Ford started life as a Dart Iron Eagle block. A Crower crank with GRP aluminum rods and Diamond custom nitrous pistons with Total Seal rings rotate inside, while a Bullet custom nitrous 55mm cam spec’d

by Sam Vincent actuates the valvetrain.

Blue Thunder 4.3 heads reworked at continued on page 72

66 66

september 2020 | RPM Magazine

Girard not only keeps his Ford all Ford but just couldn’t part with shiftin’ gears after he had his first 12-second Mustang. Now, this deep 8-second (if not much quicker, but we didn’t say that) Mustang relies on a Liberty Extreme clutchless 5-speed trans with Trick Titanium bellhousing and McLeod soft lock single disc 10.5 clutch kit all redone by Cale Aronson.

www.rpmmag.com

|

september 2020

67 67

TIGHT FIT

Martin Girard 1991 Mustang Drag Car

Chassis Type & Mods:

Power Adder:

Suspension:

Electronics:

Modified Fox Body chassis, stock front firewall/stock front and rear frame rails, mini tub,25.2 cert Chromoly roll cage originally built by Hooken Chassis Race Car in Missouri and owner modified.

Complete Racecraft front suspension (k-member, A-arms, bump steer, caster camber plates), AFCO spindle mount struts with Landrum springs, TBM spindle mount brake kit, RC Comp Hammer-S 17inch wheels.

Ladder bar rear suspension, Quartermax anti roll bar, Santhuff double adjustable rear shocks valved and done by Ron Galbreath at Afterwork Suspension, Mark Williams carbon fiber discs and pads, Weld single beadlock with 28” MT slick.

Body & Paint:

Carbon fiber front clip/hood , pro stock carbon fiber scoop, carbon fiber doors, Optic Armor windshield, carbon fiber quarter window and back glass by Crafty Fast Cars, fiberglass deck lid, Skinny Kid wing, red EP Ford paint code done by Carrosserie Xtreme.

Engine:

SBF 422 CI, iron eagle dart block, Crower lightweight crank, GRP aluminum rods, 4.175 Diamond custom nitrous pistons, Total Seal rings, Bullet custom nitrous 55mm cam spec by Sam Vincent, Jesel belt drive, Peterson external oil pump/pan vac combo , .937 Jesel lifters, Blue Thunder 4.3 heads done by Roush and reworked at BES, Victory titanium int/exh valves, PSI 1255 valve springs, PAC titanium locks and retainers, TD shaft rockers.

Custom stainless owner-built front exit headers, all engine spec by Sam Vincent and all assembly by Claude Gauthier (Atelier C.G) QC.

Induction & Fuel:

Wilson custom sheet metal intake, pro stock shear plate, 2 Pro Systems Dominator style 1050 custom nitrous carbs, Aeromotive A2000 fuel pump, Magnafuel fuel log, Holley 830 regulator and 4 port Magnafuel regulator.

68 68

september 2020 | RPM Magazine

Induction Solutions direct port first kit and second is Induction Solution Punisher System (“I have only used the first kit, for now!), Edelbrock progressive nitrous controller.

MSD billet distributor, MSD crank trigger, Fire Core custom wires, MSD Digital 7, Nitrous Dave relay panel, Racepack V300SD with all the sensors and UDX dash, Go Lithium lightweight 16volt battery.

Transmission:

Liberty Extreme clutchless 5-speed trans, Trick Titanium bellhousing, McLeod soft lock single disc 10.5 clutch kit all redone by Cale Aronson.

Rear Differential:

Modified Ford 9 inch, Mark Williams aluminium third member & spool, lightweight 4.10 Pro gear, Strange gun drilled 40-spline axles, 5/8 studs, Mark Williams billet yoke and aluminum driveshaft.

How Many Years Racing?: 20 Thanks To:

“Thank you to all the industry people who make this passion for cars and racing possible. I couldn’t do all the maintenance between the run alone; I have the best crew; Marc André Fortin, Patrick Donnelly, Gabriel Jetté, Yves Bourgeois. Thanks to all you guys! I drive the car, tune the nitrous, read the racepack and tune the clutch each run so this car needs a lot of work! This season will be quieter because of Covid 19 and closed borders but we are doing some events in Canada and looking forward to Smackdown4 at St Thomas Dragway in September. We will continue to work hard to push on those big HP turbo guys, lol. Thanks also to JB James Broaddus the promoter of the NCSB class for helping me race in the USA, it’s not always easy when you are Canadian.”

The interior of the Mustang is all about the business of drag racing, and that is to get from point A to point B before the person in the other lane.

www.rpmmag.com

|

september 2020

69 69

As well as his own stout grudge drag car Martin developed a project car with his students which has taken on a life of its own over the past 17 years.

O

ur school project car was developed to help students learn and enjoy working together for a common goal.

Every department of the school has a job on this project; the Marketing and Sales Department for sponsorship, the Body Shop for the paint and all the body work and upkeep, the Auto Mechanics shop for some of the build and modifications and ongoing mechanical work, and the Electrical/Maintenance department for the electronics of the car, we want the whole school to be involved in the car! We have a special day each year with some of the other area schools and students around Quebec at Napierville Dragway. It’s a competition but shows the students that they can have fun at the race track where it is a controlled environment.”

70 70

september 2020 | RPM Magazine

2000 CAMARO

t [[ $SBUF FOHJOF t "MM GPSHFE JOUFSOBMT XJUI NJME $BN t )PMMFZ IJ øPX JOUBLF BOE UISPUUMF CPEZ t IQ OJUSPVT TIPU 5SBOT JT 5) XJUI USBOT CSBLF t .PTFS JODI SFBSFOE XJUI HFBST

www.rpmmag.com

|

september 2020

71 71

BES were studded in place, while a Wilson custom sheet metal intake with twin Pro Systems 1050 custom nitrous carbs top off the package, well almost tops it off. Nitrous comes into the equation via 2 systems by Steve Johnson’s Induction Solutions, the first being a direct port system and the second one of Johnson’s Punisher systems.

When the car was completed, Girard decided to “switch gears” and tackle No Time and Grudge racing, starting with the No Clock Small Block class at the 2018 Yellow Bullet Nationals. He also developed an identity for the Mustang, “We named the car The TEACHER because I am a mechanics teacher at

72 72

september 2020 | RPM Magazine

CFCRS La Prairie QC.,” he said.

And at that first big race with the new car, The Teacher went to the semi-finals. Since then, they have competed at events on both sides of the border between No Clock Small Block and various 28-inch tire classes, but have had a light schedule this year due to Covid 19.

We’ve all been told at some point “when the teacher speaks, you need to listen”, and Martin did leave us with one final thought to take away with us, and that was simply; “we’ve only used the first kit, for now….”

So No Time racers take note, The Teacher is here and class is in session.

RPM

www.rpmmag.com

|

september 2020

73 73