Functions of and How to Us e User Mode (GR-700EXL-1)

19.Left swing restriction indicator lamp Lights up when the left swing limiting function is activated.

20.Number of part-lines of rope select key Used to register a number of part-lines of rope.

1. Over-front position symbol

Indicates that the boom is swung into the over-front position.

2. Outrigger state indicative symbol

Displays the way the outriggers are extended. Flashes while an outrigger state is being selected and is marked up while it registered.

3. "on-rubber" (Outrigger-not-in-use) state indicative symbol

Indicates that the on-rubber operation (non-outrigger operation) is selected. Marked up when the stationary on-rubber operation is selected, and flashes when the traveling on-rubber (creep) operation is selected.

4. Suspension lock state indicative symbol Displays that the suspensions are locked up.

5. Boom position indicator Displays the boom position in 10° increments.

Functions of and How to Us e User Mode (GR-700EXL-1)

Selecting Operational Status

WARNING

Crane operation is prohibited without full counterweigth installed.

Counterweigth state indicative symbol is marked up as shown below:

Dismounting the CounterweightMounting the Counterweight

Selecting Outrigger Status

[NOTICE]

The "on-rubber stationary" status is the default status and is automatically selected when the power supply is turned on (the PTO switch is placed in the "ON" position).

Turning the power off (PTO switch: OFF) automatically erases all the previous settings stored in memory after approximately 2 hours. To resume the operation more than 2 hours after the power has been last turned off, enter the settings all over again.

Register the outrigger state using the outrigger mode select key and the register key.

Register ゜ m

(1) On-outrigger operation

IW301-0231E14

When the outrigger mode select key is pressed, the outrigger state indicative symbol and counterweight state indicative symbol flashes in accordance with the status that the AML detects on.

After making sure that the display conforms to the actual outrigger conditions, press the register key. The outrigger state indicative symbol and counterweight state indicative symbol will change from flashing into being marked up continuously and the moment display, rated lifting capacity display and real load display will return to normal display conditions, meaning that the state has been registered.

Actual outrigger extension condition

Displayed outrigger status key

IW301-0231E11

Functions of and How to Us e User Mode (GR-700EXL-1)

(2) On-rubber operation

Press the outrigger mode select key repeatedly until the display conforms to the actual condition (on-rubber stationary operation or on-rubber creep operation). Then press the register key. The moment display, rated lifting capacity display and real load display will return to normal display conditions, meaning that the on-rubber state has been registered.

On-rubber stationary operation

On-rubber creep operation

IW301-0131E64

[NOTICE]

The outrigger status automatically changes to a on-rubber creep status when an operation is made for stowing the outrigger after the registration of the outrigger status. Be sure to again register the outrigger status, when necessary.

Functions of and How to Us e User Mode (GR-700EXL-1)

Selecting Lift Status

[NOTICE] will return to normal display conditions, meaning that the state has been registered. (When the jib set status is selected, the jib lift indicative symbol will remain flashing.)

The boom lift status is the default status and is automatically selected (the boom lift indicative symbol is marked up) when the power supply is turned on (the PTO switch is placed in the ON position).

Turning the power off (PTO switch: OFF) automatically erases all the previous settings stored in memory after approximately 2 hours. To resume the operation more than 2 hours after the power has been last turned off, enter the settings all over again.

Register the lift status using the lift mode select key and the register key.

Select the boom lift status when lifting a load on the boom with the jib mounted.

Lift mode select key

IW301-0211E13

Each time the lift mode select key is pressed, the mode changes in numerical sequence, from (1) to (9). The display returns to (1) if you press the switch while the status (9) is displayed on the screen. Select the status that corresponds to the actual lift status.

[NOTICE]

After selecting the intended lift status, press the register key to register the status. The corresponding indicative symbols will stop flashing and become marked up and the moment display, rated lifting capacity display and real load display

Jib set (mounting or stowage)