CLAAS DISCO 3050 FC PLUS DISCO 3050 FC DISCO 3050 F PLUS DISCO 3050 FDISCO 3000 FC Operator’s manual

DISCO 3050 FC PLUS DISCO 3050 FC DISCO 3050 F PLUS DISCO 3050 F DISCO 3000 FC

Operator’s manual

Re

ad an do bs er ve th es afe ty

in s

tru

cti

on

s!

EC - Declaration of Conformity according to Directive 98/37/EC

CLAAS Saulgau GmbH

We

Zeppelinstraße 2

D - 88348 Bad Saulgau

declare under our sole responsibility, that the product

Disc mower - Typ 651 „DISCO 3050 FC PLUS / 3050 FC / 3050 F PLUS / 3050 F / 3000 FC” to which this declaration relates corresponds to the relevant basic safety and health requirements of the Directive 98/37/EC Appendix 1, and to the requirements of the other relevant Directives:

-/-

For the relevant implementation of the safety and health requirements mentioned in the Directives, the following standard(s) and/or technical specification(s) has (have) been respected:

EN 745 - 1999

Bad Saulgau, 21.08.2007 Product Development (M. Geng)

Production / Supply Chain Management (A. Fetscher)

Quality Management (J. Switalski)

Introduction

Introduction

1 Introduction INTRODUCTION This operator's manual provides information concerning the use, adjustment, setting and operation of the CLAAS disc mower.

Please note that in the following chapter the CLAAS Disc Mower is also referred to as the machine.

Follow the advice on correct maintenance and servicing in order to ensure maximum performance and a long service life of your machine.

In addition, assembly of your machine and regular inspections must be carried out by your specialist workshop. Failure to carry out maintenance work, or incorrect operation will result in poor machine efficiency and loss of valuable time.

Make use of the experience and latest knowledge embodied in this machine by operating and maintaining it properly, then your cutting mechanism, mower unit will always produce good results.

Your CLAAS Service Department

Validity These operating instructions apply for all disc mowers: DISCO 3050 FC Plus / 3050 FC / 3050 F Plus / 3050 F / 3000 FC Type 651 from machine No. 651 0 1001.

1.1

BA DISCO 3050 FC Plus / 3050 FC / 3050 F Plus / 3050 F / 3000 FC - 0293 491.9

Table of contents

Table of contents

2 Table of contents 1. Introduction Introduction ............................................................................... 1.1 Validity ................................................................................ 1.1

2. Table of contents .................................................... 2.1 3. Preface Of special importance ............................................................... 3.1 Identification plate ..................................................................... 3.1

4. Safety Rules Intended use ............................................................................. 4.1 Identification of warning and danger signs ................................ 4.1 General safety and accident prevention instructions ................ 4.1 Attached machines ................................................................... 4.3 Attached devices ...................................................................... 4.3 PTO Operation .......................................................................... 4.3 Hydraulic system ....................................................................... 4.3 Tyres ......................................................................................... 4.4 Maintenance ............................................................................. 4.4 Sound pressure level ................................................................ 4.4 Safety decals with pictorials ...................................................... 4.5

5. Specifications DISCO 3050 F Plus DISCO 3050 F ..........................................................................

DISCO 3050 FC Plus DISCO 3050 FC ........................................................................

DISCO 3000 FC ........................................................................

Calculating the axial loads, minimum ballast and total weight .............................................................

Sound level from the DISCO 3050 FC PLUS / 3050 FC / 3050 F PLUS / 3050 F / 3000 FC Disc Mower ...................

5.1 5.1 5.1 5.2 5.5

6. Prior to Operation Loading and unloading machine ............................................... 6.1 Fitting ........................................................................................ 6.2 Fitting the blades ................................................................ 6.3 Mounting the deflector hood ............................................... 6.4 Check and observe the following before putting into operation! .................................................... 6.5 Mounting universal drive shaft ............................................ 6.6 Fitting on CLAAS Celtis ...................................................... 6.7 Matching the universal drive shaft ...................................... 6.8 Changing the direction of rotation ....................................... 6.9 Attachment to the tractor ......................................................... 6.10 Setting the upper link ........................................................ 6.10 Weight relief ...................................................................... 6.11 Fitting examples ............................................................... 6.14 Removing the machine ........................................................... 6.16 Prior to transportation ............................................................. 6.17 Driving on public roads ..................................................... 6.17

7. Operation Operation .................................................................................. 7.1 Working position ................................................................. 7.1

Setting the cutting height ....................................................

Ground adjustment .............................................................

Safety equipment ...............................................................

Transport position ..............................................................

Changing the swathe width ................................................

DISCO 3050 FC Plus / 3050 FC / 3000 FC .......................

DISCO 3050 F Plus / 3050 F .............................................

Conditioner .........................................................................

Changing the conditioner speed ........................................

Mowing ...............................................................................

Recommendations for environmental protection ................

Optional equipment ..................................................................

High cutting runners ...........................................................

Push-on runners .................................................................

Kit for detachable forks ......................................................

Wide deflector device DISCO 3050 FC Plus / 3050 FC / 3000 FC .......................

Three point elevation ..........................................................

7.2 7.2 7.3 7.3 7.4 7.4 7.4 7.4 7.4 7.5 7.6 7.8 7.8 7.8 7.8 7.8 7.9

8. Maintenance Important maintenance instructions ......................................... 8.1 Bolts ................................................................................... 8.1 Lubrication .......................................................................... 8.1 Guards (safety frame) ........................................................ 8.1 Drive systems ........................................................................... 8.2 Tightening the conditioner drive belt .................................. 8.2 Gearbox ............................................................................. 8.3 Mower head ....................................................................... 8.4 Mower blades ........................................................................... 8.6 Replacing mower blades .................................................... 8.6 Mower blade box ................................................................ 8.7 Mower blade quick change system DISCO 3050 FC Plus / DISCO 3050 F Plus ...................... 8.8 Screwed mower blades DISCO 3050 FC / 3050 F / 3000 FC ................................ 8.13 Attaching mower blades ................................................... 8.15 Mower discs ........................................................................... 8.16 Replacing cutting discs .................................................... 8.16 Arrangement of the pinion units ....................................... 8.18 Fitting the pinion units ...................................................... 8.18 Conditioner tines .................................................................... 8.19 Fitting / removing the tines ............................................... 8.19 Universal drive shaft ............................................................... 8.20 Maintenance of the disc coupling ..................................... 8.20 Torques ............................................................................ 8.20 Screw connections ................................................................. 8.21 Connecting elements .............................................................. 8.21 Care and cleaning .................................................................. 8.21 End of season storage ........................................................... 8.22 Malfunctions ........................................................................... 8.23

9. Lubrication chart Safety Rules ............................................................................. 9.1 Lubricants ................................................................................. 9.1 Lubrication ................................................................................ 9.1

0293 491.9 - BA DISCO 3050 FC Plus / 3050 FC / 3050 F Plus / 3050 F / 3000 FC

2.1

Preface

Preface

3 Preface OF SPECIAL IMPORTANCE To prevent accidents, these instructions must be read by everyone who uses the machine and who deals with maintenance, servicing or inspection.

It is advisable to pay particular attention to the chapter headed “Safety Rules” and “Prior to Operation”.

The use of spare parts, accessories and additional equipment which is not originally manufactured, checked and released by CLAAS can have a negative effect on specific design features of the CLAAS machine or on its operability, thereby impairing active and/or passive operating safety, as well as safety at work (accident prevention).

CLAAS will in no way be liable for damage or personal injury caused by the use of unoriginal CLAAS parts, accessories and additional equipment.

Technical specifications, dimensions and weights are understood with the usual tolerances. Modifications in the course of technical development and errors are reserved.

IMPORTANT: Front, rear, right and left are always understood as in the direction of travel.

IDENTIFICATION PLATE Always state the machine number (Fz-Ident-No.) (2) with all spare part orders and technical enquiries.

This is necessary to ensure correct delivery of spare parts.

The identification plate (1) with the machine number (Fz-Ident-No) (2) is fixed on the left side of the frame.

1

(Fig. 1, 2)

1 1

651

xxx

xxx

xxxx

65101001 2

2

3.1

BA DISCO 3050 FC Plus / 3050 FC / 3050 F Plus / 3050 F / 3000 FC - 0293 491.9

Safety Rules

Safety Rules

4 Safety Rules

ATTENTION!

Before putting the machine into operation, read the operator's manual and follow the safety precautions!

Sign to indicate instructions which must be observed. Failure to do so could result in damage to the machine.

INTENDED USE

– Measures to prevent damage to the machine.

The CLAAS disc mower is built exclusively for normal agricultural work (intended use).

The mower unit is intended for cutting stalked crops growing on the ground in natural or seeded fields.

NOTE!

Use in any other way is considered as contrary to the intended use. The manufacturer cannot be held responsible for any damage resulting from this; the risk is entirely that of the operator.

Sign to indicate instructions for a more efficient and economic use of the machine.

Designated use also includes observing the service, maintenance and repair conditions as prescribed by the manufacturer.

CAUTION!

The CLAAS mower unit may only be used, maintained and repaired by persons who are familiar with the equipment and who have been advised of the dangers involved.

Observe the pertinent accident prevention regulations and other generally acknowledged regulations regarding safety and occupational health, as well as the regulations and standards relevant to motor vehicles and traffic.

Any arbitrary modifications carried out will relieve the manufacturer of all liability for any resulting damage or injury.

IDENTIFICATION OF WARNING AND DANGER SIGNS All parts of this manual having to do with your safety or the safe operation of the machine are marked with the following signs. Please pass all safety instructions on to other users, too.

DANGER!

Sign to indicate instructions to be followed during disassembly / assembly.

ENVIRONMENT! Sign to indicate instructions which must be observed in order to avoid damage to the environment.

Danger to the environment is caused by irregular handling and incorrect disposal of toxic material (e.g. old oil).

The warning and instruction signs on the machine provide important recommendations for safe operation. These instructions involve your safety – observe them at all times!

GENERAL SAFETY AND ACCIDENT PREVENTION INSTRUCTIONS Basic rule: Always check the operating and road safety of tractor and machine before starting up!

Sign to indicate instructions which must be observed. Failure to do so would cause danger to life and limb to the operator and the people around him.

General:

– Preventive measures.

The warnings and signs provide important instructions for safe operation; observing these instructions will ensure your safety!

In addition to the advice contained in this operator's manual, comply with the general rules on safety and accident prevention.

Follow the regulations in force when using public roads!

0293 491.9 - BA DISCO 3050 FC Plus / 3050 FC / 3050 F Plus / 3050 F / 3000 FC

4.1

Safety Rules Before starting work, familiarise yourself with all the controls and instruments and their functions, as it will be too late once you have set off.

An adequate safe distance must be maintained from the cutting tools while working!

Safe operation of the mower unit is only possible through appropriate use of the cutting blades according to directions.

Check the mower unit every time for damaged, missing and worn cutting blades and replace cutting blades if necessary!

Only replace missing and damaged mower blades in sets as specified by the manufacturer to prevent danger resulting from imbalance!

Check the parts fastening the blades on every change of the cutting blades according to regulations specified by the manufacturer and replace if necessary!

It is particularly important to check how far the blade retaining pin has been grooved on its internal radius by the blade. Replace the blade holder with a new one with an unused blade retaining pin latest after achieving a groove depth of 3 mm, i.e. if the internal radius is reduced by 3 mm.

Similarly, check the riveting of the blade pin in the blade holder and the wear on the blade holder outer edge. If necessary, replace all the blade holders on the mower discs with new blade holders.

The safety guards must be checked regularly and worn or damaged safety guards must be replaced!

Protective equipment on the mower unit, for example canvases and hoods, protect against flying stones and the like as well as from access to dangerous areas.

For this reason they must be placed in safety position before starting work!

Squashing and shearing points arise while the mower unit is being swivelled from the transport position into the working position and vice versa. For this reason, do not stand between the tractor and mower. The swing process must be undertaken with the mower in horizontal position.

The glide discs must be on the ground before putting into operation and while working!

Stones and similar objects can be flung about even when the mower unit is being used correctly. Therefore, nobody should remain in the danger zone.

If you have encountered an obstacle, stop the mower unit immediately and check for damage!

Wear close-fitting clothing when working on the front attachment. Do not wear loose clothing!

Keep the machine clean to prevent fire!

Before starting and before putting it into operation, check the area around the machine (children!). Ensure that you have an adequate view!

Passengers must not be carried on the machine while working or during transport!

Always connect the machine correctly to the tractor and connect and secure the machine to the prescribed couplings!

Always place the jack in the appropriate position when hitching and unhitching the machine – stability!

Use special care when hitching the machine to the tractor and when unhitching the machine!

Make sure that balance weights are correctly fixed at the provided points!

Observe the permissible transport dimensions!

Observe the maximum permissible axle loads and total weights!

Check and mount transport equipment – such as lights, warning devices, and if required protecting devices and guards!

Operating devices (ropes, chains, linkages etc.) of remotely controlled mechanisms must be positioned in such a way that they do not trigger unintentional operation in any transport or operating position!

For road travel, prepare the machine and lock any moving parts as prescribed by the manufacturer!

Never leave the operator's platform when driving!

Always adapt your ground speed to the ground conditions! Avoid making sharp turns when driving up or down slopes or when driving across the slope!

The operating, steering and braking behaviour will be affected by the trailed machine! Therefore ensure adequate steering and braking power!

When making turns, always take into consideration the width and/or inertia of the machine!

Use the mower unit only when all the guards are fitted and in the protection position!

Special care is required when working near roads and buildings!

Ensure all persons stand clear of the operating area and of the area of danger!

The working tools of the cutter bar continue to run even after switching off the drive. Do not stay close to them until they have stopped.

Do not stand in the rotation area or swing area of the mower unit.

4.2

BA DISCO 3050 FC Plus / 3050 FC / 3050 F Plus / 3050 F / 3000 FC - 0293 491.9

Safety Rules Check for pinch and shear points on parts that are operated with external force, for instance by hydraulics!

Always disengage the PTO shaft, stop the engine and remove the main switch key before attaching or detaching the universal drive shaft!

Secure the mower unit before leaving the tractor!

Lower mounted attachments fully to the ground!

Switch off the engine and remove the ignition key.

An overload or free running coupling is to be attached on the device side when using universal drive shafts with overload or free running couplings which are not covered by the protective equipment on the tractor!

Never let anyone stand between the tractor and the machine without securing the vehicle against rolling away by putting on the parking brake and/or through the use of wheel chocks!

ATTACHED MACHINES Before attaching the machines or detaching the machines from the 3-point linkage, move the control lever to a position in which unintentional raising or lowering is not possible!

When attaching mounted machines to the 3-point linkage, the linkage categories of tractor and machine must match, otherwise make necessary modifications!

There is risk of injury due to crushing or shearing in the area of the 3-point linkage!

Do not stand between tractor and machine when operating the remote control unit for the 3-point linkage!

Always ensure that there is adequate sideways locking of the tractor three point rod when the machine is in transport position!

When driving on the road, with lifted mower unit, the operating lever must be secured against falling down.

ATTACHED DEVICES Secure the devices from rolling away.

Observe maximum permissible load capacity of couplings and swinging drawbar or hitch facility!

When hitching the machine to the drawbar, ensure that there is sufficient movement at the hitch point!

PTO OPERATION Only use universal drive shafts specified by the manufacturer!

Always ensure that the guards for the universal drive shaft and PTO stub shaft are installed and in a good condition! Ensure that the guards properly cover the universal drive shafts, both, in the transport and in the working position!

Always ensure that the universal drive shaft is correctly installed and securely fastened!

Secure universal drive shaft gear against rotating by hanging the chains.

Before engaging the PTO shaft, ensure that the selected speed and the direction of rotation of the tractor's PTO shaft matches the permissible speed and the direction of rotation of the drive assembly of the machine!

Always ensure that nobody is in the danger zone of the machine before switching on the p.t.o.shaft!

Never engage the PTO shaft when the engine has stopped!

When operating the PTO shaft nobody must stand in the vicinity of the rotating PTO stub shaft or universal drive shaft!

Always disengage the PTO shaft when the turn angle is extreme or when the PTO drive shaft is not used!

Attention, after the PTO has been disengage, flywheel mass continues to run! Do not step too close to the machine during this time! You are only allowed to work on the machine when everything has stopped moving.

Cleaning, lubricating or adjustment of the p.t.o. shaft driven machine or universal drive shaft is only permitted when the p.t.o. shaft and engine are switched and the ignition key is removed!

When the universal drive shaft is not connected to the tractor, it must be kept on the storage yoke or suspended with a chain!

After uncoupling the universal drive shaft, push the protective guard on to the PTO stub shaft!

In the event of damage, this must be rectified immediately, before commencing work with the mower unit.

HYDRAULIC SYSTEM The hydraulic system is under high pressure!

When attaching hydraulic cylinders and motors, ensure the stipulated connection of the hydraulic hoses!

0293 491.9 - BA DISCO 3050 FC Plus / 3050 FC / 3050 F Plus / 3050 F / 3000 FC

4.3

Safety Rules When connecting the hydraulic hoses to the tractor hydraulics, it is important to ensure that the hydraulics are depressurised both on the tractor side and the machine side!

For hydraulic function connections between the tractor and the machine, the coupling sleeves and plugs should be marked to avoid incorrect operation! Interchanging connections causes reversed functions (e.g. raise/lower) – Safety hazard!

Check hydraulic lines at regular intervals, and replace them in case of damage or ageing! Replaced hydraulic lines must correspond to the technical requirements of the equipment manufacturer!

Checking for leaks is hazardous. Use suitable aids to check for leaks!

Fluid escaping under high pressure (hydraulic oil) can penetrate the skin and cause serious injuries. If any fluid penetrates the skin, consult a doctor immediately!

– Risk of infections!

Before performing any work on the hydraulic system, lower the machine, release the pressure from the hydraulic system and stop the engine!

When performing maintenance work on the raised machine, ensure that it is supported safely using suitable supports!

Use suitable tools and wear safety gloves when replacing working parts!

Dispose of used oil and grease according to regulations!

Always disconnect the power supply before working on the electrical system!

Guards and protecting devices that are subject to wear must be checked at regular intervals and replaced in time!

Spare parts must at least comply with the technical standards required by the manufacturer of the machine! Original spare parts, for instance, are manufactured to meet these standards!

Before performing electrical welding work on the tractor and mounted machines, always disconnect the leads from the battery and alternator!

SOUND PRESSURE LEVEL If the sound pressure level at the driver's ear exceeds 85 dB (A) (– see Specifications, page 5.1), wear ear protection.

TYRES When working on tyres make sure the machine is safely parked and secured so that it will not roll away (use wheel chocks)!

Fitting tyres and wheels requires special training and expert knowledge and the correct tools!

Repair work on tyres on wheels must only be carried out by professionals and with correct tools!

Check the air pressure regularly! Observe the recommended tyre pressure!

MAINTENANCE Repair, service and cleaning work and elimination of malfunctions should only be performed when the drive and the are engine switched off!

– Remove the ignition key!

Wait until the cutting discs, knives are completely motionless!

Repair work on prestressed energy accumulators (springs, hydraulic accumulators etc.) should be carried out in specialist workshops and with suitable tools!

Regularly check nuts and screws for tight fit and tighten them, if necessary!

4.4

BA DISCO 3050 FC Plus / 3050 FC / 3050 F Plus / 3050 F / 3000 FC - 0293 491.9

Safety Rules

Safety Rules SAFETY DECALS WITH PICTORIALS Safety decals are attached to the danger zones of the machine. These safety decals help to alert persons to hazards which can cause personal injury. The pictorials provide instructions to avoid the hazard.

These safety signs, their placement on the machine and a brief explanatory text are shown on the following pages.

The CLAAS part number of every decal is stated ahead of the text.

The figure in ( ) refers to the adjacent picture and indicates the correct location of the decal on the machine.

Safety decals that are damaged or cannot be recognized any more must be replaced immediately by new ones.

When parts that have decals are replaced, always make sure to install the relevant new decals with each new part.

1

1

2 Warning symbol 514 946.1 (1) Before putting the machine into operation, read the operator's manual and follow the safety precautions.

(Fig. 1, 2)

0293 491.9 - BA DISCO 3050 FC Plus / 3050 FC / 3050 F Plus / 3050 F / 3000 FC

4.5

Safety Rules

2

3

4 Warning symbol 514 895.1 (2) Before carrying out maintenance and repair work switch off engine and remove ignition key.

(Fig. 3, 4)

3

5

6 Warning symbol 516 039.0 (3) Do not open or remove the safety guard with the engine running.

(Fig. 5, 6)

4.6

BA DISCO 3050 FC Plus / 3050 FC / 3050 F Plus / 3050 F / 3000 FC - 0293 491.9

Safety Rules

4

7

8 Warning symbol 514 825.0 (4) Maintain your distance when the engine is running.

(Fig. 7, 8)

5

9

STOP 10 Warning symbol 514 744.1 (5) Do not touch moving machine parts. Wait until they have come to a complete standstill.

(Fig. 9, 10)

0293 491.9 - BA DISCO 3050 FC Plus / 3050 FC / 3050 F Plus / 3050 F / 3000 FC

4.7

Safety Rules

6

11

12 Warning symbol 514 821.0 (6) Maintain sufficient distance from the blades when the engine is running.

(Fig. 11, 12)

4.8

BA DISCO 3050 FC Plus / 3050 FC / 3050 F Plus / 3050 F / 3000 FC - 0293 491.9

Specifications

Specifications

5 Specifications NOTE! Technical specifications, dimensions and weights are understood with the usual tolerances.

DISCO 3050 F PLUS DISCO 3050 F

DISCO 3050 FC PLUS DISCO 3000 FC DISCO 3050 FC

Required tractor power

KW (HP)

40 55

51 70

51 70

Hook up

Cat.

II

II

II

Transport width

m

3.00

3.00

3.00

Working width

m

3.00

3.00

3.00

P.t.o. speed

rpm

1000

1000

1000

Cutting disc speed

rpm

3200

3200

3200

metres/ second

84

84

84

rpm

-

900 / 770

900 / 770

rpm

-

950 / 710

-

mm

45

45

45

kg

780

880

880

Number of cutting discs

-

7

7

7

Number of cutting blades

-

14

14

14

Blade rotation speed Conditioner speed from Machine No.: 651 0 1687 Cut height (beam horizontal) Weight

0293 491.9 - BA DISCO 3050 FC Plus / 3050 FC / 3050 F Plus / 3050 F / 3000 FC

5.1

Specifications CALCULATING THE AXIAL LOADS, MINIMUM BALLAST AND TOTAL WEIGHT The front axle of the tractor must always be loaded with minimum 20% of the empty weight of the tractor.

The fitting of machines on the front or rear three point linkage must not result in exceeded permissible overall weight, permissible axial loading or carrying capacity of the tractor tyres.

Check that these preconditions are fulfilled by performing the following calculations or by weighing the tractor-machine combination.

You will need the following data to be able to perform the calculation:

TL GV a 68704P

GH

TH

TV b

c

TL (kg)

Empty weight of the tractor - see tractor operating instructions

TV (kg)

Front axle loading of the empty tractor - see tractor operating instructions

TV (kg)

Rear axle loading of the empty tractor - see tractor operating instructions

GH (kg) Total weight rear fitting machine / rear ballast With towed machine GH = Support load – see Specifications, page 5.1

d 1

GV (kg) Total weight front fitting machine / front ballast – see Specifications, page 5.1 a (m)

Distance between the centre of gravity front fitting machine / front ballast and the centre of the front axle – to be measured

b (m)

Tractor wheelbase, – see tractor operating instructions

c (m)

Distance between centre of rear axle and centre of lower steering ball – to be measured

d (m)

Distance between centre of lower steering ball and the centre of gravity of the rear mounted machine / rear ballast In the case of a towed machine d = 0

(Fig. 1)

5.2

BA DISCO 3050 FC Plus / 3050 FC / 3050 F Plus / 3050 F / 3000 FC - 0293 491.9

Specifications

GV min =

GH x (c + d) - TV x b + 0.2 x TL x b a+b

Calculation of the minimum ballast front Rear mounting machine or front - rear combination NOTE! Enter the calculated minimum ballast required by the front of the tractor in the table.

(Fig. 1)

GH min =

GV x a - TH x b + 0.45 x TL x b b+c+d

Calculation of the minimum ballast rear Front mounting machine NOTE! Enter the calculated minimum ballast required by the rear of the tractor in the table.

(Fig. 1)

TV tat =

GV x (a + b)- TV x b - GH x (c + d) b

Calculation of the actual front axle load In the case of a front mounted machine (GV), if the required minimum ballast value at the front (GVmin) is not reached, the weight of the front mounted machine must be increased to that of the minimum front ballast weight.

NOTE! Enter the calculated actual front axle load and that given in the operating instructions in the table.

(Fig. 1) Calculation of the actual overall weight

G tat = GV + TL + GH

With the rear mounted machine (GH), if the minimum rear ballast value (GHmin) is not reached, then the weight of the rear mounted machine must be increased to the value of the minimum ballast weight.

NOTE! Enter the calculated actual permissible overall weight and that given in the tractor operating instructions in the table.

(Fig. 1)

0293 491.9 - BA DISCO 3050 FC Plus / 3050 FC / 3050 F Plus / 3050 F / 3000 FC

5.3

Specifications Calculation of the actual rear axle load TH tat = G tat - TV tat NOTE! Enter the calculated permissible actual front axle load and that given in the operating instructions in the table.

(Fig. 1) Carrying capacity of the tyres Enter double the value (2 tyres) of the permissible tyre carrying capacity in the table (see, for example, the data provided by the tyre manufacturer).

Table

Actual value from calculation

Permissible value from operating instructions

Double permissible tyre carrying capacity (2 tyres)

---

---

Minimum ballast front / rear

kg

Overall weight

kg

≤

Front axle load

kg

≤

kg

≤

kg

Rear axle load

kg

≤

kg

≤

kg

---

NOTE! The minimum ballast must be fitted as a mounted machine or ballast weight on the tractor.

The calculated values must be less than or equal to (≤) the permissible values.

5.4

BA DISCO 3050 FC Plus / 3050 FC / 3050 F Plus / 3050 F / 3000 FC - 0293 491.9

Specifications

Sound level from the DISCO 3050 FC PLUS / 3050 FC / 3050 F PLUS / 3050 F / 3000 FC Disc Mower Sound level is determined in accordance with the measuring procedure set out in document

Not specified conditions of test are in accordance with ISO 5131.

HM Agricultural Inspectorate AGRICULTURAL MACHINERY NOISE Legislation and guidance on methods of testing (Annex to AIC 1986/117 REV) February 1988 Health and Safety Executive

Power of the tractor used for the measurement: 57 kW (78 PS) for DISCO 3050 FC Plus / 3050 FC / 3000 FC and 96 kW (137 PS) for DISCO 3050 F Plus / 3050 F. Measurement is performed with the machine stationary on a short grass level and operated at a pto speed of 1000 rpm.

The measuring method used corresponds to procedure no. 4 set out in the above document.

A = Microphone location 1

A

B

B = Microphone location 2 C = Horizontal

C

D = Machine E = Tractor

E

(Fig. 2) D

76040

2 A-evaluated equivalent permanent sound pressure levels

DISCO 3050 FC Plus DISCO 3050 FC DISCO 3000 FC

Tractor without machine

Cabin window

Tractor with machine

open

closed

open

closed

Microphone location 1 - L(A) eq

dB (A)

89.1

74.6

94.0

78.4

Microphone location 2 - L(A) eq

dB (A)

91.3

91.2

98.8

98.4

DISCO 3050 F Plus DISCO 3050 F

Tractor without machine

Cabin window

Tractor with machine

open

closed

open

closed

Microphone location 1 - L(A) eq

dB (A)

81.3

79.0

81.8

78.2

Microphone location 2 - L(A) eq

dB (A)

89.5

89.8

97.0

97.1

0293 491.9 - BA DISCO 3050 FC Plus / 3050 FC / 3050 F Plus / 3050 F / 3000 FC

5.5

Prior to Operation

Prior to Operation

6 Prior to Operation LOADING AND UNLOADING MACHINE DANGER! Incorrect loading and transport of the front attachment involves danger of accidents taking place!

1

– Suspend the machine only from the left and right slinging points (1) for loading!

1

– Make sure the slings are sufficiently dimensioned!

Weight of the machine – see Specifications, page 5.1.

(Fig. 1, 2)

1

2

6.1

BA DISCO 3050 FC Plus / 3050 FC / 3050 F Plus / 3050 F / 3000 FC - 0293 491.9

Prior to Operation DISCO 3050 FC Plus / 3050 F Plus / 3050 FC / 3050 F / 3000 FC VM8 B8

M8x25

M8x25

B8 VM8

VM8 B8 M8x25

B8

M8x25

VM8

ø12 ø12 13x26x6

13x26x6 A12 M12x65

ø12

A12 M12x65 VM12 VM12

ø12

ø12

70035

ø12

FITTING

1

Fit the safety guards on the frames according to (Fig. 1-4). Pull the rubber rope (1) through the rear safety guard. To tighten the safety guard, hang the rope (1) in the swath plate.

Fig. 2 = right hand side Fig. 3 = left hand side (Fig. 1-4)

2

3

0293 491.9 - BA DISCO 3050 FC Plus / 3050 FC / 3050 F Plus / 3050 F / 3000 FC

6.2

Prior to Operation DISCO 3050 FC Plus / 3050 FC / 3000 FC B8 VM8

1 outer M8x25

VM8 B8 8,5x30x2

B8 VM8

M8x20

M8x25 M8x25

M8x20

B8 VM8

VM8 B8

68506F

4

Fitting the blades The blades must be fitted before operating the machine for the first time.

For blade fixing with the blade quick fit system – see page 8.8, Mower blade quick change system DISCO 3050 FC Plus / DISCO 3050 F Plus.

(Fig. 5)

66605F/01

5 For bolted blades – see page 8.13, Screwed mower blades DISCO 3050 FC / 3050 F / 3000 FC. (Fig. 6)

72187

6.3

120 Nm

6

BA DISCO 3050 FC Plus / 3050 FC / 3050 F Plus / 3050 F / 3000 FC - 0293 491.9

Prior to Operation DISCO 3050 F Plus / 3050 F

3

2 12

13,5x55x5 M8x20

13x61,3x6

2

M8x25

VM8 B8 8,5x30x2

M8x25

B8 VM8

M8x25

B8 VM8 M8x25

VM8

B8 B8 VM8

M8x25 M12x55 M8x20

B8 VM8

VM8 B8 68505f

Mounting the deflector hood

7

Fit the safety guards onto the frame. Fit the cover plates (2) and the toggle nuts (3).

(Fig. 7)

0293 491.9 - BA DISCO 3050 FC Plus / 3050 FC / 3050 F Plus / 3050 F / 3000 FC

6.4

Prior to Operation CHECK AND OBSERVE THE FOLLOWING BEFORE PUTTING INTO OPERATION! 1. Check the oil levels in the gearboxes and in the cutter bar.

2. Lubricate the mower unit thoroughly before operation.

3. Check that the mower blades are properly fastened.

4. Check bolts for tightness.

5. Change over the front power lifter to single-action (just lifting, not pressing down). The mower unit lowers under its own weight. The mower unit must not be additionally loaded by the front power lifter.

6. Switch on the mower unit only when it is in lowered position.

7. Switch on the tractor PTO shaft only in idle speed and with the machine in the swung-in working position.

8. Do not exceed the permissible PTO shaft speed of the mower unit – see Specifications, page 5.1.

9. After hooking up the mower unit and engaging the universal drive shaft, by carefully lifting out and lowering the mower unit, check that the universal drive shaft rotates freely.

10. Secure universal drive shaft gear against rotating by hanging in the chains.

11. Check the safety guards for wear and damage.

12. Tell people to stay away from the danger zone and switch off the mower unit immediately if any persons come into the danger zone.

13. Never let the mower unit run without being supervised.

6.5

BA DISCO 3050 FC Plus / 3050 FC / 3050 F Plus / 3050 F / 3000 FC - 0293 491.9

Prior to Operation Mounting universal drive shaft DANGER! Never operate the universal drive shaft without the guard or if the guard is damaged - danger of injury.

– Mounting shaft guard and protective tube.

– Never remove the guards of the universal drive shaft!

– Secure the guard against rotation.

– The universal drive shafts must only be operated when in good condition.

Danger of injury by the universal drive shaft working loose during operation!

– Check that all locks are securely engaged before starting work with the PTO drive shaft.

– The fixing chains for the universal drive shaft guard to be hung up using the hook on the machine and on the tractor.

NOTE! Always engage the PTO shaft slowly to save the drive mechanism. Observe the recommendations of the PTO shaft manufacturer.

Before fitting the universal drive shaft, clean and grease the connection profile of the machine and the PTO shaft of the tractor. Pull the universal drive shaft apart and grease the sliding profile. When fitting the universal drive shaft, take care to ensure that the locks snap into place.

Fit the universal drive shaft, to do that:

• turn off the engine and remove the ignition key.

• clean and grease the universal drive shaft and the PTO shaft.

• fit the universal drive shaft first on the machine side. Then fit the universal drive shaft onto the PTO shaft of the tractor, to do that: – fit the overload safety device on the machine side.

– push in the sliding pin and push the universal drive shaft onto the connection spigot.

– take care to ensure that the sliding pin snaps into place.

0293 491.9 - BA DISCO 3050 FC Plus / 3050 FC / 3050 F Plus / 3050 F / 3000 FC

6.6

Prior to Operation • The fixing chains (1) for the universal drive shaft 1

guard to be hung up using the hook on the machine (2) and on the tractor.

2

• Check the movability of the universal drive shaft by carefully lifting and lowering the mower unit, if necessary, adjust the length of the universal drive shaft – see Matching the universal drive shaft, page 6.8.

3

• If the angle of the universal shaft is too high, fit a

8

universal shaft half with wide angle joint on the tractor side - see also Fitting on CLAAS Celtis, page 6.7.

ATTENTION! The PTO shaft may only be engaged if the machine is in the swung-in operating position!

1 (Fig. 8, 9)

9 Fitting on CLAAS Celtis CAUTION! When fitting the mower unit on the tractor CLAAS Celtis, the tractor side universal shaft half must be fitted with a wide angle joint.

• Change the universal drive shaft half.

Order no.: 000 949 087.1

6.7

Universal drive shaft half (with wide angle joint)

BA DISCO 3050 FC Plus / 3050 FC / 3050 F Plus / 3050 F / 3000 FC - 0293 491.9

Prior to Operation Matching the universal drive shaft Before using the mower unit for the first time, the hitching and universal drive shaft must be adjusted to the tractor.

CAUTION! The maximum universal drive shaft inclination and quiet running of the mower unit can only be achieved by correct hitching.

10

It may be necessary to match the universal drive shaft because of the varying PTO shaft positions of the different tractor types.

Pull the universal shaft apart and push the universal drive shaft halves onto the drive shaft of the machine and the other half onto the tractor PTO shaft using the long protective funnel.

Swing the machine into the working position. Hold the universal drive shaft halves next to each other and check the length with the machine in the lifted out and lowered positions.

(Fig. 10)

Observe the maximum permissible shaft length (LB).

Try to ensure maximum possible overlapping of profile tubes. The universal drive shaft must only be pulled apart when operating by half the size of the sliding profile cover (PU) when in a compacted condition (LZ).

In the shortest operating length, the universal drive shaft halves must not collide against each other. A minimum clearance (a) = approx. 40 mm must still be available.

Cut the male and the female guard tubes uniformly.

11

Cut the same length from the male and female profile tubes.

File the cut area to remove any metal burrs, remove any metal filings.

Grease the sliding surfaces of the profile tubes.

(Fig. 11)

0293 491.9 - BA DISCO 3050 FC Plus / 3050 FC / 3050 F Plus / 3050 F / 3000 FC

6.8

Prior to Operation Changing the direction of rotation 4 ATTENTION! Changes to the direction of rotation must be undertaken by a specialist workshop!

5

The drive of the mower unit is designed for clockwise rotating front PTO shaft.

68873

12

With tractors with an anticlockwise rotating front PTO shaft, the main gearbox (4) must be turned 180º. In addition, an anticlockwise rotating freewheel (6) must be fitted on the tractor universal drive shaft.

• Remove the main gearbox (4).

• Change over the oil sight glass (5) and the protec4

tion funnel for the PTO shaft.

• Fit the anticlockwise rotating freewheel (6).

Alternately, only the coupling housing (7) can be changed, to do that:

73736

• Remove the freewheel.

• Replace the coupling housing (7).

• Reassemble the freewheel. When fitting the keys,

13

ensure correct direction of rotation.

(Fig. 12, 13, 14)

6

The freewheel and the coupling housing can be obtained from the CLAAS spares department.

Order no.: Free-wheel

7

000 940 441.0

or Coupling housing

000 824 477.0

(Fig. 14) 73737

6.9

14

BA DISCO 3050 FC Plus / 3050 FC / 3050 F Plus / 3050 F / 3000 FC - 0293 491.9

Prior to Operation ATTACHMENT TO THE TRACTOR Completely lower the front power lifter.

Drive up to the machine and insert the Accord coupler into the three point frame.

(Fig. 15)

The latch (2) should snap into the strap (3).

(Fig. 16)

64286

15

The strap (3) can be adjusted after releasing the bolts (4).

(Fig. 16, 17)

Adjust the strap (2) so that it is in contact with the latch (2) of the Accord coupler. Adjust the stop bolt (5) accordingly (Fig. 17).

2

1

NOTE! This setting is to be undertaken with the mower unit in the lifted out position.

3

16 ATTENTION! Secure the latch (2) with the spring plug (1) (Fig. 16).

1 3

2 (Fig. 15, 16, 17)

4

5 65869-01

17 Setting the upper link The mower unit should remain horizontal when it has been lifted out i.e. it should not lift out leaning either forwards or backwards, so that the angle (a) of the two linkages of the universal drive shaft remain more or less equal in size.

a

If the position of the mower unit changes greatly when being lifted out, unequal angles will be created and this will prevent smooth running of the machine. a

(Fig. 18) 18

0293 491.9 - BA DISCO 3050 FC Plus / 3050 FC / 3050 F Plus / 3050 F / 3000 FC

6.10

Prior to Operation

6

In this case, the upper link (7) needs to be suspended higher or lower in the machine side upper link retainer or in the quick-coupler.

7

Park the tractor and mower unit on flat ground.

• Adjust the upper link so that the three point frame (6) is vertical.

(Fig. 19)

19 Weight relief The weight relief takes place using the suspension springs (8). For this purpose, the tractor must be fitted with the holders (10) and the straps (9).

9 8

The holders (10) can be obtained from the manufacturer of the front power lifter or they can be made in your own workshops.

(Fig. 20) 10

20

11

12

13

14

The straps (9) and the associated fixing material can be obtained from the CLAAS spare parts department.

12 15

Order no.: 000 480 096.0 000 235 555.0 000 239 395.1 000 949 804.1 000 233 031.0 000 238 234.0

9

74034

6.11

2x 2x 4x 2x 2x 2x

Strap (9) Hex bolt (11) M12x55 Contact washer (12) M12 Bush (13) 35x13x12 Washer (14) 13x62x6 Lock nut (15) M12

(Fig. 21) 21

BA DISCO 3050 FC Plus / 3050 FC / 3050 F Plus / 3050 F / 3000 FC - 0293 491.9

Prior to Operation The holders (10) are to be made to suit the fitting conditions on the tractor and in accordance with the dimensions (Fig. 22) – also see Fitting examples, page 6.14.

X Y

10 9

X = 300 mm Y = 20 mm Z = 480 – 650 mm

Z

Hole for the strap (9) = ø13.5 mm (Fig. 22) 22

74025

CAUTION! When making the holder or fitting the strap, make sure that • the hood of the tractor can still be opened and • the wheels do not collide with the holder or the fixing bolt of the strap.

• Fit the holder (10) on the tractor.

• Fit the strap (9) in the hole inside or

A

outside (A or B).

Hole (A) = heavy mower unit, e.g. DISCO 3050 FC Plus (with conditioner)

B

9

Hole (B) = light mower unit, e.g. DISCO 3050 F (without conditioner) (Fig. 23, 24) 10 23

A B

9 10

24

0293 491.9 - BA DISCO 3050 FC Plus / 3050 FC / 3050 F Plus / 3050 F / 3000 FC

6.12

Prior to Operation Insert the chains (17) of the suspension springs (8) into strap in a position which, in the lifted out position, is suited to the harvest conditions and the ground condition. The longer the stroke of the spring when the machine is lowered, by appropriate hanging of the chain, the greater will be the weight relief (reduced ground pressure). By changing the position of the chain suspension on the strap (9) the relief chain is either tightened or released by a half chain link.

9 8

16 17

• Deactivate the front axle suspension on the tractor.

25

If the front axle suspension cannot be deactivated, then the weight relief must be set weaker.

• Change over the front power lifter to single-action (just lifting, not pressing down).

• The chains (17) of the suspension springs (8) should be inserted into the straps (9) on the holders and secured with spring plugs (16).

ATTENTION! 8

With the mower unit lowered onto the flat ground, the tension spring (8) should not exceed a spring stroke (F) of 100 mm.

F 68800_01

26

• Check the ground pressure using a weighing scale.

The suspended mower unit should press down on the ground with a weight of 200 - 350 kg.

(Fig. 25, 26)

6.13

BA DISCO 3050 FC Plus / 3050 FC / 3050 F Plus / 3050 F / 3000 FC - 0293 491.9

Prior to Operation Fitting examples The following measurements are not definitive and must be adjusted to suit the conditions. They should be considered as guide figures for the manufacture of the holder.

Distance (W) = distance between support surface of the front power lifter and the outside of the holder Distance (X) = distance between the pivot point of the lower link and the hole (A or B) measured to the front Distance (Y) = distance between the pivot point of the lower link and the hole (A or B) measured to the back Distance (Z) = distance between the pivot point of the lower link and the hole (A or B) to the top

CLAAS Celtis 446 RX Front power lifter system: Mailleux MX R28

A

W = 77.5 mm B

Y = 20 mm Z = 480 mm (hole B)

W

Z = 585 mm (hole A)

Z

CAUTION!

Y 27

When fitting the mower unit, the tractor side universal drive shaft half must be fitted with the wide angle joint – see Fitting on CLAAS Celtis, page 6.7.

(Fig. 27)

CLAAS Ares 836 RZ A

Front power lifter system: Mailleux MX R53 X = 300 mm

B

Z = 480 mm (hole B) Z

Z = 570 mm (hole A) (Fig. 28)

X

28

0293 491.9 - BA DISCO 3050 FC Plus / 3050 FC / 3050 F Plus / 3050 F / 3000 FC

6.14

Prior to Operation CLAAS Ares 696 RZ A

Front power lifter system: Mailleux MX R38 W = 77.5 mm

B

X = 90 mm Z = 535 mm (hole B) Z

W

Z = 640 mm (hole A) (Fig. 29)

X 29 CLAAS Ares 696 RZ Front power lifter system: Sauter Type AR

A

V = 20 mm X = 155 mm

B

Z = 500 mm (hole B)

Z

Z = 600 mm (hole A)

V

The holder used is the original holder from Sauter Landtechnik, Germany.

X

Available from: www.sauter-stetten.com 30

(Fig. 30)

CLAAS Ares 836 RZ A

Front power lifter system: Zuidberg

B

W = 97 mm X = 90 mm

W

Z = 500 mm (hole B)

Z

Z = 600 mm (hole A) (Fig. 31)

X 31 Fendt Vario Favorit 716 X = 200 mm Z = 620 mm (Fig. 32) Z

X 32

6.15

BA DISCO 3050 FC Plus / 3050 FC / 3050 F Plus / 3050 F / 3000 FC - 0293 491.9

Prior to Operation REMOVING THE MACHINE ATTENTION! Park the mower unit on solid flat ground.

1

• Engage the latch (1) before removing the machine.

(Fig. 33)

33

• Remove the chains of the suspension springs and place them in the bolt (2).

(Fig. 34)

2

• Lower the mower unit to the ground.

• Remove the quick-coupler out of the three point frame (drive out).

34

• Uncouple the universal drive shaft and suspend on the three point stand using the chain (3).

(Fig. 35)

• Drive the tractor away backwards.

(Fig. 33, 34, 35)

3

35

0293 491.9 - BA DISCO 3050 FC Plus / 3050 FC / 3050 F Plus / 3050 F / 3000 FC

6.16

Prior to Operation PRIOR TO TRANSPORTATION 1. Hitch up the front mower unit.

2. Connect the universal drive shaft.

3. Swing up the outer safety guards on both sides – transport width.

4. Lift out the mower unit with the three point linkage.

5. Insert the chains of the suspension springs.

6. Insert the latch (1).

36

7. Only transport the mower unit in the switched off condition.

Take care during the transportation that the operating levers of the hydraulics do not become actuated accidentally, if necessary, block their movement.

The technically permissible axle loads and the overall weight is not to be exceeded – see Calculating the axial loads, minimum ballast and total weight, page 5.2.

1

(Fig. 36, 37) 37

Driving on public roads DANGER! When driving on public roads with the raised machine, the control lever of the hydraulics must be secured against lowering.

– Secure the control lever!

• The applicable laws and regulations must be observed when travelling on public roads!

• Observe the applicable regulations in your country.

When fitting at the front, if the distance between the back edge of the steering wheel of the tractor and the front edge of the mower unit (dimension A) (Fig. 38) is more than 3.5 m, then the reduction in visibility has to be compensated through relevant operating measures at the exits from farmyards, at road junctions and crossings e.g. by using a guide or by fitting at the back.

A A

The corresponding national (country-specific) provisions apply in other countries.

69172

6.17

38

BA DISCO 3050 FC Plus / 3050 FC / 3050 F Plus / 3050 F / 3000 FC - 0293 491.9

Prior to Operation • The vehicle ground speed must conform to the traffic and road conditions. Observe national (country-specific) provisions concerning the maximum permitted vehicle ground speed!

Reduce speed as appropriate when going around curves.

• Prepare machine for transport – see Prior to transportation, page 6.17.

• When travelling on roads, both outer safety nets must be turned upwards – Observe transport width.

• Lift the machine.

• Secure the operating levers of the hydraulics against accidental actuation.

• Insert the latch (1).

• Fit the machine with lighting.

The machine must be fitted with lighting: 39

– at the back, if the mower unit covers the rear lighting of the tractor.

– at the front, if the mower unit projects sideways more than 40 cm further than the limit lighting of the tractor.

• If necessary, connect the driving lights to the tractor.

1

(Fig. 38, 39, 40)

40

0293 491.9 - BA DISCO 3050 FC Plus / 3050 FC / 3050 F Plus / 3050 F / 3000 FC

6.18

Operation

Operation

7 Operation OPERATION DANGER! Nobody must stand in the area between the tractor and the machine when the machine is being lifted / lowered

Working position The mower head is moveable both longitudinally and laterally with respect to the direction of travel. If the latch (1) is engaged, the movement of the head downwards is limited. In normal operation, the latch should be disengaged. Then lower the mower head to the ground.

1

Fold down the safety guards – see Safety equipment, page 7.3.

(Fig. 1, 2) 1

2

1

2

7.1

BA DISCO 3050 FC Plus / 3050 FC / 3050 F Plus / 3050 F / 3000 FC - 0293 491.9

Operation Setting the cutting height ATTENTION! If the cutting height is too low, it will cause excessive wear of the mowing disc and the blades.

Z The cutting height can be adjusted by changing the tilt angle (Z) (Fig. 3) of the mower head.

68500F

3

High cut: For this, the latch (1) (Fig. 1) needs to be engaged.

The head can no longer tilt downwards so that a greater cut height is achieved. The upper link is to be shortened until the desired cut height is achieved (Fig. 4).

Low cut: For this, the latch (1) (Fig. 2) needs to be disengaged.

The springs (2) (Fig. 2) should be tightened more. The upper link is to be lengthened until the desired height of cut is achieved (Fig. 4).

4 Reducing the cut height below the prescribed height (40 mm) is not possible. In most cases, the prescribed cut height can be used to mow. The latch must then be disengaged.

With extremely uneven ground conditions, the latch should be engaged and the angle of inclination (Z) of the machine should be reduced. This produces a greater cutting height and reduces any danger of propelling foreign objects forwards.

(Fig. 1-4)

Ground adjustment X

The spring for ground adjustment in the longitudinal direction should be tightened so that the distance between the washer and the end of the thread is equal to the setting dimension X. DISCO 3050 FC Plus / 3050 FC / 3000 FC: Setting dimension X = 40 mm

DISCO 3050 F Plus / 3050 F: 5

Setting dimension X = 70 mm (Fig. 5)

0293 491.9 - BA DISCO 3050 FC Plus / 3050 FC / 3050 F Plus / 3050 F / 3000 FC

7.2

Operation Safety equipment Before entering the field to be mowed, the safety guards must be swung down on both sides. To do this:

• Swing the protection bracket (3) downwards.

3 DANGER! During operation, the mower unit must always be fitted with the safety guard.

6

Never lean on the safety guard or tread on it.

A damaged or worn safety guard should be replaced immediately.

(Fig. 6)

Transport position Swing up the outer safety guards on both sides.

Lift the mower unit and engage the latch (1).

(Fig. 7, 8)

7

1

8

7.3

BA DISCO 3050 FC Plus / 3050 FC / 3050 F Plus / 3050 F / 3000 FC - 0293 491.9

Operation Changing the swathe width DISCO 3050 FC Plus / 3050 FC / 3000 FC The swathe width can be varied by adjusting the swathe plate (4). To do this, release the spring plug (5), change the position of the swathe plate and replace the plug.

(Fig. 9)

4 5 9

DISCO 3050 F Plus / 3050 F To change the swathe width, the toggle nuts (6) must be released and moved.

Inwards: narrower swathe 6

Outwards: wider swathe Then retighten the toggle nuts (6) properly.

(Fig. 10) 6 10

Conditioner Chicane plate:

7

The chicane plate can be adjusted with the lever (7).

If the lever is pulled backwards, in other words in the direction “+”, the conditioner effect is increased. In the direction “–” it is decreased.

– +

(Fig. 11)

11

Changing the conditioner speed The conditioner speed is adjusted by changing the belt pulleys of the drive. Before doing this, the drive belts must be released and the belt guards removed.

The arrangement of the belt pulleys with respect to the conditioner speed is shown in fig. 12.

Conditioner speed – see Specifications, page 5.1.

(Fig. 12)

12

0293 491.9 - BA DISCO 3050 FC Plus / 3050 FC / 3050 F Plus / 3050 F / 3000 FC

7.4

Operation Mowing DANGER! The ground to be mowed is to be kept free from foreign objects.

• Change over the front power lifter to single-action (just lifting, not pressing down). The mower unit lowers under its own weight. The mower unit must not be additionally loaded by the front power lifter.

NOTE! When using tractors with front axle suspension, the optimum ground matching of the mower unit can no longer be guaranteed. This applies particularly when the ground is uneven.

• If necessary, deactivate the front axle suspension to achieve the set weight relief.

If the front axle suspension cannot be deactivated: • Set the weight relief weaker – see Weight relief, page 6.11 and • Reduce the traverse speed when mowing.

• Lower the mower unit to the ground.

• When working, the hydraulic control lever for the front power lifter must be set to Floating Position (freewheel).

• Swing down the safety guards on both sides.

• Before entering the field to be mowed, turn on the tractor PTO shaft and slowly accelerate to the maximum permitted PTO shaft speed (– see Specifications, page 5.1). The whistling noise of the cutting discs at high speed is completely normal and is generally muffled during actual mowing.

• Move into the forage.

• Always operate using the hand throttle while mowing to avoid fluctuations in the rotational speed.

• The driving and crawling speed are to be set according to the respective operating condition (condition of the ground, density, height and nature of the forage).

• Reduce ground speed when working in dense or flattened forage and when mowing around a curve.

• It is not possible to mow backwards with the mower unit. Raise the mower unit when reversing.

7.5

BA DISCO 3050 FC Plus / 3050 FC / 3050 F Plus / 3050 F / 3000 FC - 0293 491.9

Operation • Do not mow on rocky ground!

DANGER! When mowing with a tractor without a cab, or with open cab windows and doors, wear ear protection.

Remove the ear muffs when driving on the road.

ATTENTION! When mowing with the front mower unit, the suction sieves and coolers of the tractor engine can become very contaminated.

The tractor engine and the hydraulic unit can overheat and be damaged.

– The suction sieves and coolers of the tractor should be cleaned several times per day!

DANGER! To rectify blockages or to remove foreign bodies, switch off the PTO shaft drive, switch off the tractor engine and only when the mower discs have come to a complete standstill, leave the tractor.

Recommendations for environmental protection A simple change in the way we normally mow can help to reduce the loss of wild animals.

At the same time, the quality of the mowed crop is increased.

ENVIRONMENT! If we mow from the outside inwards, wild animals have hardly any chance of escape!

– Mow from the inside outwards.

0293 491.9 - BA DISCO 3050 FC Plus / 3050 FC / 3050 F Plus / 3050 F / 3000 FC

7.6

Operation Drive to the middle of the lot and mow from the inside outwards.

The centre can be mowed if there is enough room to turn.

Wild animals thus have the chance of escaping outwards.

(Fig. 13)

69018

13 In the case of thin long lots, mow the turns first and then mow the longitudinal sides outwards.

(Fig. 14, 15)

69019

14

69020

15 For especially long lots near the road, this technique is useful, especially with front mower units.

(Fig. 16)

69021

7.7

16

BA DISCO 3050 FC Plus / 3050 FC / 3050 F Plus / 3050 F / 3000 FC - 0293 491.9

Operation OPTIONAL EQUIPMENT High cutting runners B03 0020

1

High cutting runners with a height of 30 mm can be installed for high cutting or for operating on aggressive types of ground.

The high cutting runners (1) are mounted on the right and the left on the runners.

Order no.:

000 482 275.0

(Fig. 17) 64867

17

Push-on runners C03 0030

1

Additional runners (1) can be screwed on if the slide runners have suffered much wear.

Order no.:

000 934 150.0

(Fig. 18)

66363

18

Kit for detachable forks M03 0010 The kit for detachable forks allows connection to tractors with an 8 section PTO shaft (ø=1 3/8“). This is achieved by exchanging the detachable fork (1) of the universal drive shaft.

1

Order no.:

000 820 428.1

(Fig. 19)

67608

19

Wide deflector device DISCO 3050 FC Plus / 3050 FC / 3000 FC

1

G03 0010 Under good drying conditions or during the wet silage process, the mower unit can be fitted with deflector plates (1) for wide deflection.

Order no.:

000 923 644.0

(Fig. 20)

68807

20

0293 491.9 - BA DISCO 3050 FC Plus / 3050 FC / 3050 F Plus / 3050 F / 3000 FC

7.8

Operation Three point elevation For tractors with short lower links to increase the lifting stroke.

Fitting Fit the pin (1) with tensioning pin (2) and folding plug (3) into the holes in the straps (4).

1 A

2

B

3

Fit the straps (4) left and right on the three point stand using the provided pins (A) and folding plugs (B).

4 21

Fit the three point stand with straps (4) on the lower link.

Fit the upper link and adjust.

The required parts can be obtained from the CLAAS spare parts department.

Order no.:

000 925 689.0

(Fig. 21)

7.9

BA DISCO 3050 FC Plus / 3050 FC / 3050 F Plus / 3050 F / 3000 FC - 0293 491.9

Maintenance

Maintenance

8 Maintenance

Guards (safety frame) DANGER!

IMPORTANT MAINTENANCE INSTRUCTIONS

Folding safety guards may only be opened when the drive is switched off and the engine is at a standstill.

DANGER! Repair, service and cleaning work and troubleshooting should only be performed when the drive and engine are switched off!

– Remove the ignition key!

– Remove the ignition key!

Mount the guards again after completion of maintenance and repair work.

Check the guards at regular intervals.

DANGER!

Worn or damaged safety devices must be replaced by new ones.

Undertake repair, maintenance and cleaning work on the raised machine only when it is securely supported.

– Use suitable stands!

Bolts Check all bolts for tightness and retighten if necessary.

Check that all split pins and roll pins are in place.

Lubrication Observe the oil change intervals and the oil quality specified by the manufacturer. Use only good quality grease or oil to lubricate the machine. Clean the grease nipples before applying the grease gun.

Grease all points that require lubrication, observing the intervals specified in the lubrication chart.

The stipulated lubrication intervals apply to normal service conditions only. Lubricate more frequently if the machine is used under severe conditions.

NOTE! The stipulated fill quantities are only approximate values, the definitive values for the correct oil level is always the oil level check.

ENVIRONMENT! Dispose of oil and grease according to regulations!

0293 491.9 - BA DISCO 3050 FC Plus / 3050 FC / 3050 F Plus / 3050 F / 3000 FC

8.1

Maintenance

Maintenance DRIVE SYSTEMS 1

DANGER! Carry out work on V belts only when the mower unit is switched off and when it is secured against being switched on again.

2

– Remove the ignition key!

(130 mm)

3

Tightening the conditioner drive belt 67636

1

Retighten the V-belt if necessary. Then conduct regular checks after that.

1 3

Check the belt tension after 5 working hours after initial commissioning.

2

CAUTION! Do not over-tighten the belt To tighten the belt on the mower unit:

2

• Screw in the tensioning bolt (1).

• The belts are correctly tightened if compression springs (2) are pretightened to the height of the angle plate (3).

• Check the belt tension on a regular basis.

CAUTION! If a V belt is worn or broken, the complete set of V belts is to be replaced.

(Fig. 1, 2)

8.2

BA DISCO 3050 FC Plus / 3050 FC / 3050 F Plus / 3050 F / 3000 FC - 0293 491.9

Maintenance Gearbox For lubrication of the gearbox, use only gearbox oil SAE 85W-90 in accordance with (MIL-L-2105B) API-GL-5-90. Check the oil level daily and if necessary, correct. To check the oil level, lower the mower unit onto flat ground.

1

NOTE! 2

3

3

The stipulated fill quantities are only approximate values, the definitive values for the correct oil level is always the oil level check.

The oil bubble must be in the centre of star in the oil sight glass (3) (Fig. 3).

6 Oil filling capacity: 3050 FC Plus / 3050 FC / 3000 FC Main gearbox: 2.0 litres

4

1 = Oil filling screw (remove the right universal drive shaft)

5

2 = Oil drain screw (remove the right universal drive shaft) 4

3 = Oil sight glass (Fig. 3)

Side gearbox: 1.0 litre 4 = Check screw and oil filling screw 5 = Oil drain screw 6 = Breather valve (Fig. 4)

Remove the breather valve (6) (Fig. 4) after the first 10 operating hours and clean. Thereafter check the breather valve at regular intervals to ensure that it is in perfect working order and clean it.

(Fig. 3, 4)

0293 491.9 - BA DISCO 3050 FC Plus / 3050 FC / 3050 F Plus / 3050 F / 3000 FC

8.3

Maintenance 3050 F Plus / 3050 F 9

NOTE! The stipulated fill quantities are only approximate values, the definitive values for the correct oil level is always the oil level check.

7

8

Main gearbox: 0.85 litres 7 = Oil filling screw 5

8 = Oil drain screw 9 = Oil sight glass (Fig. 5)

Mower head DANGER! After extended operation, the mower head can reach temperatures up to around 80° C. – Danger of burning!

– Do not touch the bar!

1

– Wear safety gloves!

6

Only use EP SAE 90 gear oil to lubricate the cutting disk gearbox. Check the oil level in the mower head daily and if necessary, correct.

NOTE! The stipulated fill quantities are only approximate values, the definitive values for the correct oil level is always the oil level check.

2

Oil filling quantity: max. 4.5 litres 1 = Oil filler and oil level check plug 7

2 = Oil drain screw (Fig. 6, 7)

8.4

BA DISCO 3050 FC Plus / 3050 FC / 3050 F Plus / 3050 F / 3000 FC - 0293 491.9

Maintenance Checking the oil level:

• Run the machine until it is hot and place on flat

1

ground.

• Lift the mower head and support on the right side with a 100 mm wooden beam, for example.

4-6mm

• Lower the head so that the left side rests on the ground and the right side is on the wooden beam.

• Use the upper link to set the head inclination to 0º, in other words, horizontal.

100 2

73744

• Check the oil level through the check opening (1) 8

(Fig. 8) with a dipstick. Insert the dipstick at right angles to the head up to the bottom of the head.

• Oil level height: approx. 4-6 mm If the oil level in the head cannot exactly be identified, then all the oil should be drained and replaced by fresh oil of the specified quantity.

(Fig. 8, 9)

73354

9 Oil change: After commissioning or after a gearbox overhaul, change the oil for the first time after 50 working hours, then every 200 working hours and, at the latest, after each harvesting season.

Draining oil: 2

• Lift the mower head and let it warm up for a period of approx. 8 - 10 minutes.

• Drain oil through the opening of the magnetic plug (2).

10

• Clean the magnetic plug before reinstalling it.

NOTE! If the maintenance instructions are observed, there is no reason to worry if the header becomes very hot as long as the cutting disks can still be easily rotated manually with the machine at operating temperature. An operating temperature of approx. 60° C must be considered normal. .

(Fig. 10)

0293 491.9 - BA DISCO 3050 FC Plus / 3050 FC / 3050 F Plus / 3050 F / 3000 FC

8.5

Maintenance MOWER BLADES Replacing mower blades 1

DANGER! The folding guards (1) of the mower unit may only be opened when the PTO shaft is switched off and when the engine and mower discs are at a standstill.

Work on the mower blades or their fasteners only when the drive has stopped and the engine and cutting discs are switched off.

11

– Switch off mower drive.

– Switch off engine.

– Wait until the mower discs have come to a complete standstill before leaving the tractor!

– Remove the ignition key!

– Remove the universal drive shaft!

– Wear gloves when working on the mower blades!

(Fig. 11) ATTENTION! Always check the mower blades before operation and after driving into an obstacle!

– Always check that the mower blades are correctly seated!

– Worn, damaged or bent blades must be replaced immediately. Do not weld or straighten!

– Both mower blades on every cutting disc must be attached or replaced, because otherwise the mower head may be damaged by imbalanced blades.

Replacement blades must meet the minimum technical requirements specified by CLAAS. This is always achieved by using original CLAAS mower blades!

8.6

BA DISCO 3050 FC Plus / 3050 FC / 3050 F Plus / 3050 F / 3000 FC - 0293 491.9

Maintenance

NOTE! Use only sharp mower blades for neat cutting.

Use of blunt blades requires more power and reduces the cutting quality.

Blunt blades can be reversed and fastened to the same disk so the other blade is used for cutting.

Mower blade box

DISCO 3050 FC Plus / 3050 FC / 3000 FC

There is a mower blade box (2) on the left side of the headstock which contains spare mower blades.

2

The mower blade box (2) can be taken out of its holder by loosening the spring (3).

(Fig. 12, 13)

3

12 DISCO 3050 F Plus / 3050 F

2

3

13 4 = Stowage space for mower blades 0952 043.0 5 = Stowage space for mower blades 0952 042.0 (Fig. 14, 15)

2

5 4

14

0293 491.9 - BA DISCO 3050 FC Plus / 3050 FC / 3050 F Plus / 3050 F / 3000 FC

8.7

Maintenance The mower blade box full of mower blades (2) should be used to change mower blades on the mower head.

(Fig. 15)

2 15

Mower blade quick change system DISCO 3050 FC Plus / DISCO 3050 F Plus 6

To change the mower blades:

• Insert the fitting lever (7) between the mower disc (6) and the mower blade holder (3) (Fig. 16, 18).

7 NOTE! Pull the fitting lever (7) outwards parallel to the mower disc axis to the stop (Fig. 17).

8 66602F/01

16

• Rotate the mower disc so that the mower blade holder (10) when pushing down the fitting lever (7) fits exactly into the depression (9) of the groove (Fig. 18).

• Clean the depression (9) before changing the mower blade.

7

8 66603F/01

8.8

17

BA DISCO 3050 FC Plus / 3050 FC / 3050 F Plus / 3050 F / 3000 FC - 0293 491.9

Maintenance • Push the fitting lever (7) downwards and remove the mower blade (8). Fit a new mower blade, or turn the mower blade over if the second cutting edge has not been used (Fig. 18, 19).

6 7

NOTE!

10 66604F/01

9

8

18

The mower blades for anticlockwise and clockwise rotating mower discs are different.

The direction of rotation of each disc is marked by an arrow on the blade (Fig. 14, 20).

In the direction of rotation, the cutting edge points downwards (Fig. 18).

6

7 8 66605F/01

19

63875_01

20

ATTENTION! Take extra care to ensure that the mower blades and the mower blade retaining pins are correctly located! The mower blade retaining pin (11) must be in contact (see arrow) and must sit straight in the locating hole of the disc.

11

(Fig. 21) 66606F

21

0293 491.9 - BA DISCO 3050 FC Plus / 3050 FC / 3050 F Plus / 3050 F / 3000 FC

8.9

Maintenance The fitting lever (7) can also be used as a stop for the mower discs when undertaking maintenance work on the mower head. For this, the drift (12) of the fitting lever (7) should be inserted into the hole of a groove.

The handle of the fitting lever (7) must be parallel to the mower head when doing this. Hit the mower disc (6) on the fitting lever (7) and stop in this manner.

7 6

(Fig. 22)

12

66615F

7

22 After changing the mower blades and after completion of maintenance work, the fitting lever (7) can be removed from the bracket (13).

13

(Fig. 23)

23 The mower blades must be replaced under the following conditions: – If the blades are cracked or bent. Never attempt to straighten a bent blade.

– If the blades are worn.

The width (B) of the blade, measured 10 mm from the edge of the disc, should be at least 36 mm.

10 mm

(Fig. 24) B B 68777

24 – If the drilled hole in the blade is widened.

Maximum allowable widening of the drilled hole of Ln = 18 mm to L = 20 mm.

L

(Fig. 25)

Ln Ln 61623

8.10

25

BA DISCO 3050 FC Plus / 3050 FC / 3050 F Plus / 3050 F / 3000 FC - 0293 491.9

Maintenance The attachment parts of the mower blades must be checked before every use.

ATTENTION! Replace damaged mower blades, mower blade holders and mower discs!

Do not weld or straighten!

15 mm 12 mm

The mower blades must be replaced under the following conditions: 66612F

26

– If wear is apparent on the mower blade holder shape (Fig. 26).

– If wear is apparent on the mower blade holder thickness (Fig. 27).

– If there are visible cracks or excessive wear on the weld beads (S) on the mower blade retainer pin (Fig. 27).

S ATTENTION! Check the weld beads before each commissioning!

4 mm

3 mm

S

66610F

27 (Fig. 26, 27)

– If there is deformation (bending) of the mower blade holder.

– If the mower blade retaining pin (11) no longer sits straight in the locating hole of the disc.

(Fig. 28)

11 66607F

28 – If there is a gap between the mower blade retainer pin (11) and the locating hole (see arrow) of the disc.

(Fig. 29)

11 66608F

29

0293 491.9 - BA DISCO 3050 FC Plus / 3050 FC / 3050 F Plus / 3050 F / 3000 FC

8.11

Maintenance – If the mower blade retainer pin (11) is worn down to x = 13 mm. x

Damaged or worn mower blade retainers must always be replaced.

Replacement blades must meet the minimum technical requirements specified by CLAAS. This is always achieved by using original CLAAS mower blades!

ATTENTION!

11 66609F

Damaged mower blades, mower blade holders and mower discs should be replaced Do not weld or straighten!

30

(Fig. 30)

The discs must be replaced under the following conditions: – If the locating hole shows expansion, wear or damage over the entire diameter area.

(Fig. 31) 66613F

8.12

31

BA DISCO 3050 FC Plus / 3050 FC / 3050 F Plus / 3050 F / 3000 FC - 0293 491.9

Maintenance

73743

32

Screwed mower blades DISCO 3050 FC / 3050 F / 3000 FC

6

Replacing mower blades

• To replace blades, first clean the seat of the nut (6) and loosen the nut with the socket wrench.

• Fit a new mower blade, or turn the mower blade over if the second cutting edge has not been used.

NOTE! 72187

120 Nm

33

Note the direction of rotation when mounting new mower blades!

• The direction of rotation of each disc is marked by an arrow on the blade. In the direction of rotation, the cutting edge points downwards.

ATTENTION! Secure the nuts with DELO ML 5328 single-component liquid plastic (order no. 0201 802.1) or Loctite Type 242 (order no. 0666 285.0) every time they are replaced.

• Replace bolt and nut (6).

0293 491.9 - BA DISCO 3050 FC Plus / 3050 FC / 3050 F Plus / 3050 F / 3000 FC

8.13

Maintenance Tightening torque of the mower blade securing bolt = 120 Nm. (Fig. 32, 33)

ATTENTION! Replace damaged mower blades, mower blade holders and mower discs!

Do not weld or straighten!

B The mower blades must be replaced under the following conditions: – If the blades are cracked or bent.

34

Never attempt to straighten a bent blade.

– If the blades are worn.

The width (B) of the blade, measured 10 mm from the edge of the disc, should be at least 36 mm (Fig. 34).

L

– If the drilled hole in the blade is widened.

Maximum allowable widening of the drilled hole of Ln = 18 mm to L = 20 mm (Fig. 35).

(Fig. 34, 35)

Ln 61623

8.14

35

BA DISCO 3050 FC Plus / 3050 FC / 3050 F Plus / 3050 F / 3000 FC - 0293 491.9

Maintenance Attaching mower blades The attachment parts of the mower blades must be checked before every use.

ATTENTION! Always ensure proper seating when installing the securing screws.

61625

36

The mower blade securing bolts must be replaced under the following conditions: – Visible deformation of the securing bolt (e.g. after running into an obstacle).

D

– Missing or ineffective thread coating, caused by water, oil or dirt.

Dn

– In the case of serious wear of the bolt head to the blade surface (Fig. 36).

– If the bolt shaft is worn from Dn = 18 mm to D = 15 mm (Fig. 37).

(Fig. 36, 37)

61624

37 The blade securing nuts must be replaced in the following cases: 7

– If the spring contact washer (7) has lost its elastic properties or has become detached from the nut.

– If the nut has worn out so much that dimension a = H/2.

a

61626

(Fig. 38)

H

38

0293 491.9 - BA DISCO 3050 FC Plus / 3050 FC / 3050 F Plus / 3050 F / 3000 FC

8.15

Maintenance MOWER DISCS

90

ATTENTION! Replace damaged mower blades, mower blade holders and mower discs!

Do not weld or straighten!

Worn or damaged cutting discs must be replaced immediately.

61628

39

Replacing cutting discs 2

ATTENTION!

1

The discs must be arranged so the long dimension is at right angles to the adjacent disc. The discs must always be arranged like this to prevent the mower blades from colliding.

(Fig. 39) 71806

40 The cutting discs are fastened to one flange each.

The bolts (1) for securing the cutting discs must be tightened as specified.

Tightening torque: Bolts (1) = 80 Nm Nuts (2) = 350 Nm. (Fig. 40)

8.16

BA DISCO 3050 FC Plus / 3050 FC / 3050 F Plus / 3050 F / 3000 FC - 0293 491.9

Maintenance

ATTENTION!

3

Replace a missing damaged cover immediately, otherwise the attachment could fill up with material. This could lead to an imbalance and severe consequential damage.

– The cutting discs with attachment (4) must always be covered with a plastic cover (3).

4

41 Ensure that the drainage opening (5) at the bottom of the conveyor cones is always open. This is the only place for draining water that has collected here (e.g. high-pressure steam cleaning).

(Fig. 41, 42)

5 42

0293 491.9 - BA DISCO 3050 FC Plus / 3050 FC / 3050 F Plus / 3050 F / 3000 FC

8.17

Maintenance

B

A

A

A

E

B

A

43

Arrangement of the pinion units In the mower head, there are six pinion units mounted next to the infeed drive module. These pinion units are subdivided into four A versions and two B versions.

The B versions have a red mark on the underside. The fitting arrangement of the pinion units is shown in fig. 43.

(Fig. 43)

Fitting the pinion units Pinion unit A: The notches (K) of the pinion shaft (2), the centre of the tooth (Z) and the centre of the flange hole must be in line.

Pinion unit B: The notches (K) of the pinion shaft (2), the centre of the tooth (Z) and the centre between the two flange holes must be in line.

2

67638

44

(Fig. 44, 45)

30˚ Z

Z

K

K

2

68802_01

A

2

B 45

8.18

BA DISCO 3050 FC Plus / 3050 FC / 3050 F Plus / 3050 F / 3000 FC - 0293 491.9

Maintenance

c d

c d

c d c d

c d

c d

c d

1

2

63622F

46

CONDITIONER TINES Fitting / removing the tines In the accessories, there is a pin (1) with which the clamping pin (2) can be knocked in or knocked out.

NOTE! Fit the tines in accordance with the fitting diagram fig. 46.

(Fig. 46)

0293 491.9 - BA DISCO 3050 FC Plus / 3050 FC / 3050 F Plus / 3050 F / 3000 FC

8.19

Maintenance UNIVERSAL DRIVE SHAFT Service the PTO drive shaft in accordance with the instructions of the PTO drive shaft manufacturer (see operation manual of the manufacturer).

Observe the safety instructions of the manufacturer!

Immediately replace damaged or missing protective tubes, universal drive shaft guards and securing chains.

Protect the universal drive shaft from the effects of the weather.

47

The protective tubes must be greased to prevent freezing during winter.

After longer periods of standstill, relubricate the universal drive shaft and check the readiness for operation.

Operate the universal drive shaft only in good condition.

Maintenance of the disc coupling After longer periods of standstill, the coupling should be released.

48

To do this, tighten the hex nuts of the studs completely.

Stuck friction linings should be released by rotating the coupling hub by hand.

Then turn back the hex nuts or studs to the end of the thread again.

(Fig. 47)

Fig. 48 = new condition Replace worn friction discs in good time.

49

The friction discs are worn if the pressure washer edge (arrow) is no longer visible (Fig. 49).

(Fig. 47, 48, 49)

Torques 1

Friction coupling (1) with 4 friction discs = 1200 Nm (Fig. 50)

50

8.20

BA DISCO 3050 FC Plus / 3050 FC / 3050 F Plus / 3050 F / 3000 FC - 0293 491.9

Maintenance Friction coupling (2) with 2 friction discs = 1050 Nm

2

(Fig. 51)

66934

51

SCREW CONNECTIONS After 10 operating hours, check all bolts and nuts on the machine and retighten. Check at regular intervals!

CONNECTING ELEMENTS All connecting elements which affect safety such as bolts, screws, pins etc. should be checked regularly for wear and deformation.

If necessary, the connecting elements must be replaced by new ones.

CARE AND CLEANING

• Do not use a high pressure cleaner or steam jet for cleaning cut-out clutches or bearing, hydraulic or electrical parts.

– There is a risk of damage and rust formation.

• Cleaning with too high a pressure can cause damage to paintwork.

• After cleaning the machine with a high pressure cleaner, the bearing points must be greased before and after the wash.

Carry out a short test run afterwards, so that any water that has penetrated the bearings will be forced out.

There should be a collar of grease on the bearings.

This protects the bearings from the ingress of dirt, plant sap and water.

0293 491.9 - BA DISCO 3050 FC Plus / 3050 FC / 3050 F Plus / 3050 F / 3000 FC

8.21

Maintenance END OF SEASON STORAGE 1. Clean the dirt from the mower unit.

2. Drain the oil from the angle gearbox and from the mower head and refill with new oil to the prescribed oil level.

3. Lubricate all lubrication points thoroughly until grease comes out of the bearings (see lubrication chart). Let the mower unit run for a short time.

4. Check the mower unit for wear and damage and repair if required.

5. Remove V-belt and store safely in a dry place.

6. Clean mower unit and all rust marks and repair any paint damage.

7. Store the mower unit in a dry, weather-protected room where no artificial manure is stored.

8. Store in working position.

8.22

BA DISCO 3050 FC Plus / 3050 FC / 3050 F Plus / 3050 F / 3000 FC - 0293 491.9

Maintenance MALFUNCTIONS Cause Vibration

– Plastic cover missing.

Remedy

• Clean the attachment on the cutting disc and the plastic cover immediately.

– Feeder drum dirty.

• Clean the feeder drum.

Poor adaptation to ground contours

– Wrongly adjusted frame.

• Reduce weight relief.

• Clean the links and lubricate.

Wrong tilting angle of the mower head

– Upper link length wrongly adjusted.

– Joints on mower head seized.

• Turn the upper link out or in.

• Engage or disengage the latch.

• Adjust the spring pressure.

Poor cutting quality (for overly high forage/storage forage)

– Tilt of mower head too large.

– PTO speed too low.

– Ground speed too high.

• Reduce tilt of the mower head.

• Reduce ground speed.

• Replace mower blades.

– Blunt or damaged mower blades.

Stubble too high

– Wrongly adjusted tilt of the mower head.

• Change tilt of the mower head by adjusting the upper link.

• Engage or disengage the latch.

• Adjust the spring pressure.

Fodder pushed forwards before being cut (creating stripes)

– Swirling effect of the mower blades in light crops.

• Reduce p.t.o. speed and

Swathe too small

– Crops growing too thickly.

• Remove the guide plates.

Accumulation of dirt between the runners

– Very moist working conditions.

• Increase the spring weight

– Mole hills – Insufficient load relief for the machine.

Increased wear on cutting disc and mower blades

– Very difficult working conditions.

increase ground speed.

relief.

• Increase cutting height.

• If necessary, lift up and down.

• Clean mower unit.

• Fit high cut glide grooves.

• Increase the spring weight relief

0293 491.9 - BA DISCO 3050 FC Plus / 3050 FC / 3050 F Plus / 3050 F / 3000 FC

8.23

Maintenance

Cause Increased wear on runners

Remedy

– Stony, sandy ground – Runners not lying parallel to the ground.

• Fit wear grooves.

• Increase the spring weight relief.

• Adjust the grooves flat to the ground (in the case of extreme high cut point wear of the groove).

Build up of piles in the swathe

– Light and wet crops.

– Hilly terrain

• Mount an additional conveyer hat.

• Reduce ground speed.

Plugs on the swathe plate

– Strong crops

• Swing swathe plate outwards.

– Wrong mounting of the swathe plate.

Winding of the outer conveyer drum

– Strong and flattened crops.

• Check rotational speed, increase if necessary.

• Check the lining of the slipping clutch.

Preparer wound

– High tractor speed drop.

– Strong and flattened crops.

• Increase the belt tension.

• Check rotational speed, increase if necessary.

• Reduce the traverse speed.

• Open the chicane more.

• Swing swathe plate outwards.

8.24

BA DISCO 3050 FC Plus / 3050 FC / 3050 F Plus / 3050 F / 3000 FC - 0293 491.9

Lubrication chart

Lubrication chart

9 Lubrication chart SAFETY RULES DANGER! Lubrication of the mower unit only when the tractor engine is at a standstill.

– Remove the ignition key!

LUBRICANTS Trademarked lubrication grease e. g.

FINA

“Marson EPL 2”

ARAL

“Aralub HLP 2”

FUCHS “Rendit TEP 2” SHELL

“Retinax EP 2” or “Alvania G3”

DEA

“Glisando EP”

FAG

“Arcanol L 135 V”

SKF

“LGEP2”

Trademarked gearbox oil SAE90 - API GL 4

LUBRICATION

Lubricate these grease points every 20 working hours.

Lubricate these grease points every 100 working hours.

Lubricate these grease points every 250 working hours.

0293 491.9 - BA DISCO 3050 FC Plus / 3050 FC / 3050 F Plus / 3050 F / 3000 FC

9.1

Lubrication chart

Lubrication chart

1

2

3

4

5

9.2

BA DISCO 3050 FC Plus / 3050 FC / 3050 F Plus / 3050 F / 3000 FC - 0293 491.9

Lubrication chart

6

7

8

9

10

0293 491.9 - BA DISCO 3050 FC Plus / 3050 FC / 3050 F Plus / 3050 F / 3000 FC

11

9.3

At CLAAS KGaA mbH we are constantly improving our products to reflect the latest technological developments.

For this reason, we may from time to time need to make changes to diagrams and descriptions in this documentation which do not reflect products which have already been delivered and which will not be implemented on these machines.

Technical data, dimensions and weights are understood with the usual tolerances. Responsibility for errors or omissions not accepted.

Reproduction or translation of this publication, in whole or part, is not permitted without the written consent of the CLAAS KGaA mbH. All rights under the provision of the Copyright Act are reserved.

CLAAS KGaA mbH 33426 Harsewinkel Germany

CLAAS KGaA mbH Postfach 1163 33426 Harsewinkel - Germany Tel.: +49 (0) 5247 12-0 www.claas.com

0293 491.9 BA DISCO 3050 FC Plus / 3050 FC / 3050 F Plus / 3050 F / 3000 FC EN - 08.07 Printed in Germany