Elabscience's Rat TCF20 ELISA

ElabscienceÂŽ

ie nc e

4th Edition, revised in May, 2019

El ab sc

(FOR RESEARCH USE ONLY. DO NOT USE IT IN CLINICAL DIAGNOSTICS !)

Rat TCF20(Transcription factor 20) ELISA Kit

Synonyms: TCF20, AR1, SPBP, TCF-20, transcription factor 20 (AR1), transcription factor 20, Nuclear factor SPBP,

El ab sc ie n

ce

Nuclear factor SPBP, Protein AR1, Stromelysin-1 PDGF-responsive element-binding protein, SPRE-binding protein Catalog No : E-EL-R1005 96T This manual must be read attentively and completely before using this product.

If you have any problems, please contact our Technical Service Center for help (info in the header of each page).

Phone: 240-252-7368(USA) 240-252-7376(USA) Email: techsupport@elabscience.com Website: www.elabscience.com

ie nc e

ab sc ie nc e

Please refer to specific expiry date from label on the side of box.

El

ab

sc

nc e ie sc El ab

ie n

ce

El

ab sc

El

Please kindly provide us with the lot number (on the outside of the box) of the kit for more efficient service.

4th Edition, revised in May, 2019

El ab sc

ie nc e

Intended use This ELISA kit applies to the in vitro quantitative determination of Rat TCF20 concentrations in serum, plasma and other biological fluids.

Specification ●Sensitivity: 18.75 pg/mL ●Detection Range: 31.25-2000 pg/mL

El ab sc ie n

ce

●Specificity: This kit recognizes Rat TCF20 in samples. No Significant cross-reactivity or interference between Rat TCF20 and analogues was observed. ●Repeatability: Coefficient of variation is < 10%.

Test principle This ELISA kit uses the Sandwich-ELISA principle. The micro ELISA plate provided in this kit has been pre-coated with an antibody specific to Rat TCF20. Standards or samples are added to the micro ELISA plate wells and combined with the specific antibody. Then a biotinylated detection antibody specific for Rat TCF20 and Avidin-Horseradish Peroxidase (HRP) conjugate are added successively to each micro plate well and incubated. Free components are washed away. The substrate solution is added to each well. Only those wells that contain Rat TCF20, biotinylated detection antibody and Avidin-HRP conjugate will appear blue in color. The enzyme-substrate reaction is terminated by the addition of stop solution and the color turns yellow. The optical density (OD) is measured spectrophotometrically at a wavelength of 450 nm ± 2 nm. The OD value is proportional to the concentration of Rat TCF20. You can calculate the concentration of Rat

El

ab

sc

nc e ie sc El ab

ie n

ce

El

ab sc

El

ie nc e

ab sc ie nc e

TCF20 in the samples by comparing the OD of the samples to the standard curve.

4th Edition, revised in May, 2019

Specifications

Micro ELISA Plate (Dismountable)

8 wells ×12 strips

Reference Standard

2 vials

Concentrated Biotinylated Detection Ab (100×)

1 vial, 120 μL

Storage

El ab sc

Item

ie nc e

Kit components & Storage An unopened kit can be stored at 2-8℃ for 1 month. If the kit is not used within 1 month, store the items separately according to the following conditions once the kit is received.

El ab sc ie n

ce

-20℃, 6 months

1 vial, 120 μL

Reference Standard & Sample Diluent

1 vial, 20 mL

Biotinylated Detection Ab Diluent

1 vial, 14 mL

HRP Conjugate Diluent

1 vial, 14 mL

Concentrated Wash Buffer (25×)

1 vial, 30 mL

Substrate Reagent

1 vial, 10 mL

4°C(shading light)

Stop Solution

1 vial, 10 mL

4°C

Plate Sealer

5 pieces

Product Description

1 copy

Certificate of Analysis

1 copy

-20°C(shading light), 6 months

4°C, 6 months

ie nc e

All reagent bottle caps must be tightened to prevent evaporation and microbial pollution.

The volume of reagents in partial shipments is a little more than the volume marked on the label, please use accurate measuring equipment instead of directly pouring into the vial(s).

El

Note:

ab sc ie nc e

Concentrated HRP Conjugate (100×)

Other supplies required

ab sc

Microplate reader with 450 nm wavelength filter

nc e ie sc El ab

ce ie n

Loading slot for Wash Buffer

sc

Absorbent paper

ab

Deionized or distilled water

El

Incubator capable of maintaining 37℃

El

High-precision transfer pipette, EP tubes and disposable pipette tips

ie nc e

4th Edition, revised in May, 2019

Note

El ab sc ie n

ce

El ab sc

1. Please wear lab coats, eye protection and latex gloves for protection. Please perform the experiment following the national security protocols of biological laboratories, especially when detecting blood samples or other bodily fluids.

2. A freshly opened ELISA Plate may appear to have a water-like substance, which is normal and will not have any impact on the experimental results.

3. Do not reuse the reconstituted standard, biotinylated detection Ab working solution, concentrated HRP conjugate working solution. The unspent undiluted concentrated biotinylated detection Ab (100×) and other stock solutions should be stored according to the storage conditions in the above table.

4. The microplate reader should have a 450(±10 nm) filter installed and a detector that can detect the wavelength. The optical density should be within 0~3.5.

5. Do not mix or use components from other lots.

6. Change pipette tips in between adding standards, in between sample additions, and in between reagent additions.

Also, use separate reservoirs for each reagent.

Sample collection Serum: Allow samples to clot for 2 hours at room temperature or overnight at 2-8℃ before centrifugation for 15 min at 1000×g at 2-8℃. Collect the supernatant to carry out the assay. Blood collection tubes should be disposable and be nonendotoxin.

Plasma: Collect plasma using EDTA or heparin as an anticoagulant. Centrifuge samples for 15 min at 1000×g at 2-8℃ within 30 min of collection. Collect the supernatant to carry out the assay. Hemolysed samples are not suitable for ELISA

ab sc ie nc e

assay!

Cell lysates: For adherent cells, gently wash the cells with moderate amount of pre-cooled PBS and dissociate the cells

ie nc e

using trypsin. Collect the cell suspension into a centrifuge tube and centrifuge for 5 min at 1000×g. Discard the medium

El

and wash the cells 3 times with pre-cooled PBS. For each 1×106 cells, add 150-250 μL of pre-cooled PBS to keep the cells suspended. Repeat the freeze-thaw process several times until the cells are fully lysed. Centrifuge for 10min at cycles.

ab sc

1500×g at 2-8℃. Remove the cell fragments, collect the supernatant to carry out the assay. Avoid repeated freeze-thaw

Tissue homogenates: It is recommended to get detailed references from the literature before analyzing different tissue types. For general information, hemolysed blood may affect the results, so the tissues should be minced into small pieces

El

and rinsed in ice-cold PBS (0.01M, pH=7.4) to remove excess blood thoroughly. Tissue pieces should be weighed and then homogenized in PBS (tissue weight (g): PBS (mL) volume=1:9) with a glass homogenizer on ice. To further break down the cells, you can sonicate the suspension with an ultrasonic cell disrupter or subject it to freeze-thaw cycles. The homogenates are then centrifuged for 5 min at 5000×g to get the supernatant.

Cell culture supernatant or other biological fluids: Centrifuge samples for 20 min at 1000×g at 2-8℃. Collect the

El

ab

sc

nc e ie sc El ab

ie n

ce

supernatant to carry out the assay.

ie nc e

4th Edition, revised in May, 2019

Note for sample:

El

ab

sc

nc e ie sc El ab

ie n

ce

El

ab sc

El

ie nc e

ab sc ie nc e

El ab sc ie n

ce

El ab sc

1. Samples should be assayed within 7 days when stored at 2-8℃, otherwise samples must be divided up and stored at -20℃ (≤1 month) or -80℃ (≤3 months). Avoid repeated freeze-thaw cycles.

2. Please predict the concentration before assaying. If the sample concentration is not within the range of the standard curve, users must determine the optimal sample dilutions for their particular experiments.

3. If the sample type is not included in the manual, a preliminary experiment is suggested to verify the validity.

4. If a lysis buffer is used to prepare tissue homogenates or cell culture supernatant, there is a possibility of causing a deviation due to the introduced chemical substance.

5. Some recombinant protein may not be detected due to a mismatching with the coated antibody or detection antibody.

ie nc e

4th Edition, revised in May, 2019

Reagent preparation

El ab sc

1. Bring all reagents to room temperature (18~25℃) before use. Follow the Microplate reader manual for set-up and preheat it for 15 min before OD measurement.

2. Wash Buffer: Dilute 30 mL of Concentrated Wash Buffer with 720 mL of deionized or distilled water to prepare 750 mL of Wash Buffer.Note: if crystals have formed in the concentrate, warm it in a 40℃ water bath and mix it gently until the crystals have completely dissolved

2000

1000

500

250

125

62.5

31.25

0

ie nc e

ab sc ie nc e

El ab sc ie n

ce

3. Standard working solution: Centrifuge the standard at 10,000×g for 1 min. Add 1.0 mL of Reference Standard &Sample Diluent, let it stand for 10 min and invert it gently several times. After it dissolves fully, mix it thoroughly with a pipette. This reconstitution produces a working solution of 2000 pg/mL. Then make serial dilutions as needed.

The recommended dilution gradient is as follows: 2000, 1000, 500, 250, 125, 62.5, 31.25, 0 pg/mL. Dilution method: Take 7 EP tubes, add 500uL of Reference Standard & Sample Diluent to each tube. Pipette 500uL of the 2000 pg/mL working solution to the first tube and mix up to produce a 1000 pg/mL working solution. Pipette 500uL of the solution from the former tube into the latter one according to these steps. The illustration below is for reference. Note: the last tube is regarded as a blank. Don’t pipette solution into it from the former tube.

El

ab

sc

nc e ie sc El ab

ie n

ce

El

ab sc

El

4. Biotinylated Detection Ab working solution: Calculate the required amount before the experiment (100 μL/well).

In preparation, slightly more than calculated should be prepared. Centrifuge the stock tube before use, dilute the 100× Concentrated Biotinylated Detection Ab to 1×working solution with Biotinylated Detection Ab Diluent.

5. Concentrated HRP Conjugate working solution: Calculate the required amount before the experiment (100 μL/well). In preparation, slightly more than calculated should be prepared. Dilute the 100× Concentrated HRP Conjugate to 1× working solution with Concentrated HRP Conjugate Diluent.

ie nc e

4th Edition, revised in May, 2019

Assay procedure (A brief assay procedure is on the 11th page)

El ab sc

1. Add the Standard working solution to the first two columns: Each concentration of the solution is added in duplicate, to one well each, side by side (100 uL for each well). Add the samples to the other wells (100 uL for each well). Cover the plate with the sealer provided in the kit. Incubate for 90 min at 37℃. Note: solutions should be added to the bottom of the micro ELISA plate well, avoid touching the inside wall and causing foaming as much as possible.

El ab sc ie n

ce

2. Remove the liquid out of each well, do not wash. Immediately add 100 μL of Biotinylated Detection Ab working solution to each well. Cover with the Plate sealer. Gently mix up. Incubate for 1 hour at 37°C. 3. Aspirate or decant the solution from each well, add 350 uL of wash buffer to each well. Soak for 1~2 min and aspirate or decant the solution from each well and pat it dry against clean absorbent paper. Repeat this wash step 3 times. Note: a microplate washer can be used in this step and other wash steps.

4. Add 100 μL of HRP Conjugate working solution to each well. Cover with the Plate sealer. Incubate for 30 min at 37°C. 5. Aspirate or decant the solution from each well, repeat the wash process for five times as conducted in step 3.

6. Add 90 μL of Substrate Reagent to each well. Cover with a new plate sealer. Incubate for about 15 min at 37°C. Protect the plate from light. Note: the reaction time can be shortened or extended according to the actual color change, but not more than 30min.

7. Add 50 μL of Stop Solution to each well. Note: Adding the stop solution should be done in the same order as the substrate solution.

El

ab

sc

nc e ie sc El ab

ie n

ce

El

ab sc

El

ie nc e

ab sc ie nc e

8. Determine the optical density (OD value) of each well at once with a micro-plate reader set to 450 nm.

ie nc e

4th Edition, revised in May, 2019

Calculation of results

Average the duplicate readings for each standard and samples, then subtract the average zero standard optical density.

El ab sc

Plot a four-parameter logistic curve on log-log graph paper, with standard concentration on the x-axis and OD values on the y-axis.

If the samples have been diluted, the concentration calculated from the standard curve must be multiplied by the dilution factor. If the OD of the sample surpasses the upper limit of the standard curve, you should re-test it with an appropriate

El ab sc ie n

ce

dilution. The actual concentration is the calculated concentration multiplied by the dilution factor.

Typical data As the OD values of the standard curve may vary according to the conditions of the actual assay performance (e.g. operator, pipetting technique, washing technique or temperature effects), the operator should establish a standard curve for each test. Typical standard curve and data is provided below for reference only.

1000

500

250

125

62.5

31.25

0

OD

2.533

1.707

1

0.523

0.265

0.184

0.134

0.082

Corrected OD

2.451

1.625

0.918

0.441

0.183

0.102

0.052

-

El

ab

sc

nc e ie sc El ab

ie n

ce

El

ab sc

El

ie nc e

ab sc ie nc e

Concentration(pg/mL) 2000

ie nc e

4th Edition, revised in May, 2019

1

2

3

n

20

20

20

Mean(pg/mL)

102.85

315.21

Standard deviation

5.75

C V (%)

5.59

El ab sc ie n

ce

Sample

El ab sc

Precision Intra-assay Precision (Precision within an assay): 3 samples with low, mid range and high level Rat TCF20 were tested 20 times on one plate, respectively.

Inter-assay Precision (Precision between assays): 3 samples with low, mid range and high level Rat TCF20 were tested on 3 different plates, 20 replicates in each plate.

Intra-assay Precision Inter-assay Precision 1

2

3

20

20

20

955.07

99.18

308.08

931.49

15.19

46.03

6.71

15.50

33.44

4.82

4.82

6.77

5.03

3.59

Recovery The recovery of Rat TCF20 spiked at three different levels in samples throughout the range of the assay was evaluated in various matrices.

Sample Type Range (%) Average Recovery (%) 88-101

95

EDTA plasma (n=5)

91-106

98

Cell culture media (n=5)

92-106

98

ab sc ie nc e

Serum (n=5)

Cell culture media(n=5)

Range (%)

85-97

96-112

86-98

Average (%)

92

104

91

Range (%)

86-102

84-96

87-98

Average (%)

93

90

92

Range (%)

89-103

84-98

85-101

Average (%)

94

89

92

Range (%)

87-100

79-93

88-99

Average (%)

93

86

94

ie sc El ab

ie n

ce

El sc

1:16

ab

1:8

El

1:4

nc e

EDTA plasma(n=5)

ab sc

Serum (n=5)

El 1:2

ie nc e

Linearity Samples were spiked with high concentrations of Rat TCF20 and diluted with Reference Standard & Sample Diluent to produce samples with values within the range of the assay.

ie nc e

4th Edition, revised in May, 2019

Troubleshooting Causes

Solutions

El ab sc

Problem

Inaccurate pipetting Poor standard curve

Check pipettes.

Ensure briefly spin the vial of standard

Improper standard dilution

and dissolve the powder thoroughly by

El ab sc ie n

ce

gentle mixing.

Wells are not completely aspirated

Completely aspirate wells in between steps.

Insufficient incubation time

Ensure sufficient incubation time.

Use recommended incubation

Incorrect assay temperature

temperature. Bring substrate to room

Low signal

temperature before use.

Inadequate reagent volumes

Check pipettes and ensure correct preparation.

Improper dilution HRP conjugate inactive or TMB failure

Mix HRP conjugate and TMB, rapid

Plate reader setting is not optimal

heat.

Inaccurate pipetting

Check pipettes.

ab sc

Large CV

Concentration of target protein is too high

Plate is insufficiently washed

El

High background

on the Microplate reader.

Open the Microplate Reader ahead to pre-

El

Deep color but low value

Verify the wavelength and filter setting

ie nc e

ab sc ie nc e

coloring.

Use recommended dilution factor.

Review the manual for proper wash. If using a plate washer, check that all ports are unobstructed.

Contaminated wash buffer

Prepare fresh wash buffer.

Improper storage of the ELISA kit

All the reagents should be stored according to the instructions.

Low sensitivity Stop solution is not added

Stop solution should be added to each

El

ab

sc

Copyright Š2018-2020 Elabscience Biotechnology Inc. All Rights Reserved

nc e ie sc El ab

ie n

ce

well before measurement.

ie nc e

4th Edition, revised in May, 2019

SUMMARY

ce

El ab sc

Add 100 μL standard or sample to each well. Incubate for 90 min at 37°C. Remove the liquid. Add 100 μL Biotinylated Detection Ab. Incubate for 1 hour at 37°C. Aspirate and wash 3 times.

Add 100 μL HRP Conjugate. Incubate for 30 min at 37°C. Aspirate and wash 5 times.

Add 90 μL Substrate Reagent. Incubate for 15 min at 37°C. Add 50 μL Stop Solution. Read at 450 nm immediately.

Calculation of results.

El ab sc ie n

1.

2.

3.

4.

5.

6.

7.

8.

Declaration

El

ab

sc Powered by TCPDF (www.tcpdf.org)

nc e ie sc El ab

ie n

ce

El

ab sc

El

ie nc e

ab sc ie nc e

1. Limited by current conditions and scientific technology, we can't conduct comprehensive identification and analysis on all the raw material provided. So there might be some qualitative and technical risks for users using the kit.

2. The final experimental results will be closely related to the validity of products, operational skills of the operators and the experimental environments. Please make sure that sufficient samples are available.

3. To get the best results, please only use the reagents supplied by the manufacturer and strictly comply with the instructions!

4. Incorrect results may occur because of incorrect operations during the reagents preparation and loading, as well as incorrect parameter settings of the Micro-plate reader. Please read the instructions carefully and adjust the instrument prior to the experiment.

5. Even the same operator might get different results in two separate experiments. In order to get reproducible results, the operation of every step in the assay should be controlled.

6. Every kit has strictly passed QC test. However, results from end users might be inconsistent with our data due to some variables such as transportation conditions, different lab equipments, and so on. Intra-assay variance among kits from different batches might arise from the above reasons, too.