SPILLER PARK

EXISTING AWNING & STOREFONT BY LL TO REMAIN UNCHANGED

Team: Max Boston, Jayita Shetty

SIGNAGE NOTES:

1.SIGN MANUF. TO VERIFY

SIGNAGE IS PROVIDED & INSTALLED IN COMPLIANCE

W/ CITY OF ATL SIGN

ORDINANCE FOR PROPERTIES

ZONED (SP-1 SA6/HC -20H / A&E SIGN OVERLAY)

2.SIGN MANUF. TO SUBMIT SHOP DWGS. FOR LANDLORD APPROVAL PRIOR TO FABRICATION AND INSTALLATION, TYP.

NON-ILLUM. TENANT SIGNAGE ON EXTG.SIGN BAND TO BE PROVIDED & INSTALLED BY SIGN MANUF.

BLADE SIGN. VERIFY MOUNTING HEIGHT W/ SHOP DWGS

2'-6"

5'-1"

EXISTING DOOR TO REMAIN

The scope of work is in an existing commercial space. The proposed scope of work consisted of the interior remodel with construction of new interior walls. The work includes ceiling and floor plans. Reworking and installation of new doors. The new design for kitchen and serving area includes new millwork and details. The project was completed with the permit drawing

NEW VINYL DECAL BY OWNER ON STOREFRONT WINDOW

EXTERIOR STOREFRONT ELEVATION 1/4" = 1'-0"

PT-3

MOULDING, TYP.

INSTALLED IN COMPLIANCE ORDINANCE FOR PROPERTIES ZONED (SP-1 SA6/HC -20H /

EXISTING STOREFRONT ENTRY DOORS AND WINDOWS TO REMAIN

INTERIOR STOREFRONT ELEVATION

CHANDELIERS AS SCHEDULED, TYP.

FIXTURE HEIGHT WITH OWNER

PAINT TRIM, MOULDING, TYP. DISPLAY SHELVING AT BACK

INTERIOR ELEVATION 1/4" = 1'-0"

ELEVATION CUT

SHOWN AT SUSPENDED SOFFIT FEATURE

INTERIOR ELEVATION

WITH OWNER

KEY LEGEND

INTERIOR ELEVATION 1/4" = 1'-0"

PROVIDE & INSTALL NEW LIGHTS AT SUSPENDED SOFFIT

SHOP DWGS. FOR LANDLORD

PAINT TRIM, MOULDING, TYP.

NON-ILLUM. TENANT SIGNAGE ON EXTG.SIGN BAND TO BE PROVIDED & INSTALLED BY SIGN MANUF.

W/ SHOP DWGS

Architectural Floor Plan

EXTERIOR STOREFRONT ELEVATION

1/4" = 1'-0"

PIN MOUNTED LOGO SIGN BY SIGN VENDOR. COORDINATE W/ OWNER

PIN MOUNTED LOGO SIGN BY SIGN VENDOR. COORDINATE W/ OWNER

1. ALL MARKINGS OF MEANS OF EGRESS SHALL INCLUDE TACTILE EXIT SIGNAGE IF/AS REQUIRED BY GEORGIA FIRE PREVENTION CODE AND NFPA 101.

2. LOCATE FIRE EXTINGUISHERS AS SHOWN ON THE PLAN.

3. ALL EGRESS DOORS SHALL BE EQUIPPED WITH PANIC HARDWARE IF/AS REQUIRED BY THE GEORGIA FIRE PREVENTION CODE AND NFPA 101. T.G.C. SHALL VERIFY THAT EXISTING EGRESS DOORS ARE EQUIPPED WITH THE REQUIRED

4. SEE FINISH PLAN & SCHEDULE ON SHEET A3.1 AND INTERIOR ELEVATIONS ON SHEET A2.1 FOR WALL, FLOOR AND CEILING

INTERIOR ELEVATION

1/4" = 1'-0"

DISPLAY SHELVING AT BACK

EXISTING AWNING & STOREFONT BY LL TO REMAIN UNCHANGED NEW VINYL DECAL BY OWNER ON STOREFRONT WINDOW EXISTING DOOR TO REMAIN INTERIOR ELEVATION 1/4"

ACCESS TO EXISTING PUBLIC

PROVIDE & INSTALL NEW 60-MIN. FIRE RATED DOOR AS SCHEDULED. G.C. TO VERIFY EXISTING OR PROVIDE ACCESSIBLE, BEVELED THRESHOLD AT FLOOR FINISH TRANSITION.

FURR OUT TO PROVIDE FOR PLUMBING CHASE WALLS. SEE WALL TYPE LEGEND, TYP.

PROVIDE DECORATIVE MILLWORK FAUX COLUMNS ON FINISH SIDE OF NEW FURRED-OUT WALL TO MATCH EXISTING COLUMNS / BEAMS, TYP. X2. SEE MILLWORK PLAN & INTERIOR ELEVATIONS FOR MORE INFORMATION.

WATER HEATER ON DRIP PAN IN SERVICE / UTILITY CLOSET

EXISTING AWNING & STOREFONT BY LL TO REMAIN UNCHANGED

SIGNAGE NOTES:

NON-ILLUM. TENANT SIGNAGE ON EXTG.SIGN BAND TO BE PROVIDED & INSTALLED BY SIGN MANUF.

EXISTING NON-RATED PARTITION WALL, REPAIR IF/AS NEEDED. SEE SHELL BUILDING DRAWINGS FOR MORE INFORMATION.

INTERIOR STOREFRONT ELEVATION

CHANDELIERS AS SCHEDULED, TYP.

CHANDELIERS AS SCHEDULED, TYP.

VERIFY FIXTURE HEIGHT WITH OWNER

VERIFY FIXTURE HEIGHT WITH OWNER

EXISTING STOREFRONT ENTRY DOORS AND WINDOWS TO REMAIN

EXISTING STOREFRONT ENTRY DOORS AND WINDOWS TO REMAIN

INTERIOR STOREFRONT ELEVATION

PAINT TRIM, MOULDING, TYP. PT-3

1.SIGN MANUF. TO VERIFY SIGNAGE IS PROVIDED & INSTALLED IN COMPLIANCE W/ CITY OF ATL SIGN ORDINANCE FOR PROPERTIES ZONED (SP-1 SA6/HC -20H / A&E SIGN OVERLAY)

1-HOUR RATED FIRE BARRIER. REPAIR IF/AS NEEDED WHILE MAINTAINING EXISTING FIRE RATING. SEE SHELL BUILDING DRAWINGS FOR MORE INFORMATION.

2-HOUR RATED FIRE BARRIER. REPAIR IF/AS NEEDED WHILE MAINTAINING EXISTING FIRE RATING. SEE SHELL BUILDING DRAWINGS FOR MORE INFORMATION.

1.SIGN MANUF. TO VERIFY SIGNAGE IS PROVIDED & INSTALLED IN COMPLIANCE W/ CITY OF ATL SIGN ORDINANCE FOR PROPERTIES ZONED (SP-1 SA6/HC -20H / A&E SIGN OVERLAY)

2.SIGN MANUF. TO SUBMIT SHOP DWGS. FOR LANDLORD APPROVAL PRIOR TO FABRICATION AND INSTALLATION, TYP.

2.SIGN MANUF. TO SUBMIT SHOP DWGS. FOR LANDLORD APPROVAL PRIOR TO INSTALLATION, TYP.

NEW INTERIOR PARTITION: 3-5/8" METAL STUDS AT 16" O.C. WITH 1 LAYER GYPSUM BOARD EACH FINISH SIDE. EXTEND UP TO UNDERSIDE OF CEILING ABOVE. PROVIDE FINAL FINISHES AS SCHEDULED ON FINISH PLANS / SCHEDULE. NOTE: PROVIDE MOISTURE RESISTANT GYPSUM BOARD IN WET LOCATIONS, TYP.

NEW PARTIAL HEIGHT MILLWORK PARTITION BELOW COUNTERTOP: 3-5/8" METAL STUDS AT 16" O.C. WITH 1 LAYER GYPSUM BOARD EACH FINISH SIDE. PROVIDE FINAL FINISHES AS SCHEDULED ON FINISH PLANS / SCHEDULE. NOTE: PROVIDE MOISTURE RESISTANT GYPSUM BOARD IN WET LOCATIONS, TYP.; HEIGHT OF WALL VARIESREFERENCE MILLWORK PLAN / ELEVATIONS.

NEW VINYL DECAL BY OWNER ON STOREFRONT WINDOW EXISTING DOOR TO REMAIN

NEW VINYL DECAL BY OWNER ON STOREFRONT WINDOW EXISTING DOOR TO REMAIN

EXTERIOR STOREFRONT ELEVATION 1/4" = 1'-0"

EXTERIOR STOREFRONT ELEVATION

NEW INTERIOR FURR-OUT W/ 3-5/8" METAL STUDS AT 16" O.C. FLUSH AGAINST EXISTING WALL WITH 1 LAYER GYPSUM BOARD ON FINISH SIDE. EXTEND UP TO UNDERSIDE OF CEILING ABOVE. PROVIDE MOISTURE RESISTANT GYPSUM BOARD IN WET LOCATIONS, TYP.

1/4" = 1'-0"

B.O. EXISTING BEAMS @ 11'-4" A.F.F. (VERIFY)

@ 11'-4"

A.F.F. (VERIFY)

PAINT TRIM, MOULDING, TYP.

PAINT TRIM, MOULDING, TYP.

= 1'-0"

PROVIDE FULL OVERLAY DOORS w/ CONCEALED EUROPEAN STYLE HINGES. EXTERIOR OF CABINET AND DOORS TO 1 1 2 6"

2 SECTION @ TRASH RECEPTACLE

2 WALL B-3 B-3

SECTION AT FRONT BAR COUNTER 1"=1'-0" 6" 3" 19" SATIN BRASS PURSE HOOK MOUNTED IN RECESS, TO BE INSTALLED INVERSELY. PROVIDE BLOCKING IF/AS NECESSARY PROVIDE WOOD FINISH WD-2 ON CUSTOMER SIDE OF MILLWORK B-2 20" 36" 42" 18" PL. LAM. PL-1 SEE PLANS FINISH ALL EXPOSED EDGES w/ TYPICAL BULLNOSE EDGE OF SURROUNDING CABINET WD-2 3" 6" 36"

ROUTING. INSTALL IN CS-1 WD-2 3/4" WATER RESISTANT PLYWOOD, TYP. W/ PLAM AT INTERIOR SURFACES

7

GROMMET SEE PLANS

PER TENANT DIRECTION PROVIDE FULL OVERLAY DOORS w/ CONCEALED EUROPEAN STYLE HINGES. EXTERIOR OF CABINET AND DOORS TO BE WD-2 FINISH PL-1 B-2

B-3 BACK SPLASH TO MATCH COUNTER

LINE OF SALES SOFFIT FEATURE SHOWN DASHED ABOVE LINE OF EXISTING BEAM ABOVE SHOWN DASHED, TYP. X2

7 42" 8 SECTION AT FRONT BAR COUNTER 1"=1'-0" w/ TYP. BULLNOSE. 34" 19" SATIN BRASS PURSE HOOK MOUNTED IN RECESS, TO BE INSTALLED INVERSELY. PROVIDE BLOCKING IF/AS NECESSARY PROVIDE WOOD FINISH WD-2 ON CUSTOMER SIDE OF MILLWORK B-2

CS-1 3/4" X 3/4" X 1/8" CONT. STEEL ANGLE FRAME. IF AS NEEDED

SATIN BRASS PURSE HOOK MOUNTED IN RECESS, TO BE INSTALLED INVERSELY. PROVIDE BLOCKING IF/AS NECESSARY ICE STORAGE BIN SHOWN IN DOTTED

WOOD FINISH WD-2 ON CUSTOMER SIDE OF MILLWORK 20" 13" 18" 6"

SOLID SURFACE COUNTERTOP NOSING w/ TYP. BULLNOSE. EXTEND BULLNOSE TO 2" TO COVER TILE EVENLY. FINISH COUNTERS W/ KNEE WALL AT FRONTLINE SALES COUNTER/MILLWORK FINISH W/ WD-2

SEE PLANS 34"

CASH DRAWER

ADJUSTABLE SHELF SEAL ALL INTERIOR SILICONE CAULK CORNERS W/

PL. LAM. PL-1

13" 6"

PROVIDE 2" PLASTIC GROMMET FOR WIRE ROUTING. INSTALL IN FIELD PER TENANT DIRECTION

CS-1 COUNTERTOP PAINT GRADE WOOD

CS-1 B-3 B-2

A4.2 2 6"

ACCESSIBLE HEIGHT MILLWORK POINT OF SALES / SALES REGISTER 42" TALL PARTIAL HEIGHT WALL / LEDGE AT CUSTOMER SIDE OF ESPRESSO BAR A2.1

TO 36"

B-3

WD-2

36" PL. LAM. PL-1

6"

4 SECTION AT OPEN WORK COUNTER, TYP. 1"=1'-0" 3 SECTION AT P.O.S. 1"=1'-0"

BARSINK/HANDSINK

SEE PLANS 2 X 4 PRESSURE TREATED BLOCKING-TYPICAL EXTEND FLR/BASE INTO CABINET.

WALL 4" TALL BACK SPLASH TO MATCH COUNTER PROVIDE OPENING AT CABINET BASE FOR ROUTING INDIRECT WASTE TO FLOOR SINK LOCATED UNDER MILLWORK 6 SECTION AT SINK, TYP. 1"=1'-0"

+42" A.F.F. +42" A.F.F.

CS-01 CS-01

3/4" THK. TYP. SHELF SUPPORT BACK SPLASH TO MATCH COUNTER WD-2 WD-2 PL. LAM. PL-1 PAINT GRADE WOOD ON CUSTOMER SIDE AND FRP ON EMPLOYEE SIDE OF KNEE WALL WD-2 FRP 1 ENLARGED 3/4"

Millwork Notes

EXISTING WALL AND FLOOR FINISHES TO REMAIN TO THE GREATEST EXTENT POSSIBLE.

SEE SHEET A4.3 FOR CONDIMENT STATION MILLWORK DETAIL

PROVIDE BRASS SCHLUTER STRIP AT CORNER TRANSITIONS WHERE WT-1 FINISH OCCURS, TYP. MTL-1

4" BACKSPLASH AT COUNTERS ALONG WALLS IN SALES AREA, TYP. CS-01

PLAM. WRAPPED PLYWOOD ALL INTERIOR SIDES OF BACK SALES AREA MILLWORK, TYP. PROVIDE WD-2 AT VISIBLE SURFACES. PL-1

OPEN BELOW COFFEE BAR SEATING. PROVIDE AND INSTALL SUPPORT COUNTERTOP W/ BRACKETS PER MANUF.,

PROVIDE WOOD TRIM (TO MATCH EXISTING) ON TOP OF NEW FURRED OUT WALL AT LOCATIONS OF EXISTING COLUMNS.