Yale C856 (MP20 25HD 30HD) Service Manual - PDF DOWNLOAD

Yale Axcess Online

Notepad About User Settings Feedback Help Log Out

Marina, your selected truck is C856 (MP20/25HD/30HD)

Select a Truck Truck Details Mast Details

Search Publications

View Cart: Pick List 2 Announcements Parts Info Service Manuals Software Support Items

Service Manuals Manuals Available For C856 (MP20/25HD/30HD) Manual

Manual Title

272486700

Controller Electronic COMBI

272487200

Multifunction Digital Instrument (MDI)

272490600

Reducer

272495100

Service Repair Manual =>C856X01516A

524186010

Service Repair Manual C856X01517A=>

©2012 Yale Axcess Online

http://www.yaleaxcessonline.com/eng/myt/truck_details.cfm?action=422.02.2012 15:44:37

http://www.yaleaxcessonline.com/lib/service/itwservice/272486700/index.htm

P.N. 272486700

Technical Information for YALE Service Centres

This manual is addressed exclusively to the specialised technicians of the Yale service network CONTROLLER ELECTRONIC

http://www.yaleaxcessonline.com/lib/service/itwservice/272486700/index.htm (1 of 2)22.02.2012 15:45:39

http://www.yaleaxcessonline.com/lib/service/itwservice/272486700/index.htm

COMBI Section: INDEX

http://www.yaleaxcessonline.com/lib/service/itwservice/272486700/index.htm (2 of 2)22.02.2012 15:45:39

http://www.yaleaxcessonline.com/lib/service/itwservice/272486700/TOC.htm

INDEX 1.0 MECHANICAL DIMENSIONS 2.0 ELECTRONIC CONTROLLER 3.0 INTRODUCTION 3.1 MOTOR CURRENT ABSORPTION TABLE 3.2 FUNCTIONAL CHARACTERISTICS 3.3 SCHEMATIC DIAGRAM 3.4 PROTECTION DEVICES 3.5 CONTROLLER DIAGNOSTICS 3.6 OPERATING PRINCIPLE 3.7 DEFINITION OF TRAVEL DIRECTION 3.8-3.8.1 INTRODUCTION TO THE PROGRAMMING CONSOLE 3.8.2 USE OF THE PROGRAMMING CONSOLE 3.8.3 CONNECTION TO THE CHOPPER 3.8.4 DESCRIPTION OF THE CONSOLE MENU 3.9 DESCRIPTION OF CONNECTOR INPUTS 3.9.1 CONNECTOR WIRING DIAGRAM 3.9.2 PROGRAMMING OF CONNECTOR “E” INPUTS 3.9.3 DESCRIPTION OF CONNECTOR “B” FUNCTIONS 3.10 PROGRAMMING TABLE 3.11 PARAMETER CHANGE, DESCRIPTION OF THE PARAMETERS 3.12 CONFIG. MENU ADJUSTMENTS 3.13 CONFIG. MENU SET OPTIONS 3.14 PROGRAMMING LEVEL EQUIVALENCE TABLE 3.15 TESTER MENU TABLE 3.16 DESCRIPTION OF TESTER FUNCTIONS 3.17 DESCRIPTION OF ALARMS 4.0 DESCRIPTION OF SERIAL TILLER 4.1 SCHEMATIC DIAGRAM 4.2 DESCRIPTION OF HALL EFFECT SENSORS

http://www.yaleaxcessonline.com/lib/service/itwservice/272486700/TOC.htm22.02.2012 15:45:51

http://www.yaleaxcessonline.com/lib/service/itwservice/272486700/Y_naen/c1a.htm

1.0 MECHANICAL DIMENSIONS OF THE COMBI CONTROLLER

2.0 COMBI ELECTRONIC CONTROLLER

http://www.yaleaxcessonline.com/lib/service/itwservice/272486700/Y_naen/c1a.htm (1 of 17)22.02.2012 15:46:20

http://www.yaleaxcessonline.com/lib/service/itwservice/272486700/Y_naen/c1a.htm

2.1 TABLE OF COMPONENTS

http://www.yaleaxcessonline.com/lib/service/itwservice/272486700/Y_naen/c1a.htm (2 of 17)22.02.2012 15:46:20

http://www.yaleaxcessonline.com/lib/service/itwservice/272486700/Y_naen/c1a.htm

3.0 ELECTRONIC CONTROLLER FOR DRIVE MOTOR AND PUMP MOTOR INTRODUCTION The COMBI controller, used for control of the drive motor, is the latest evolution of high-frequency MOS technology and operates at a frequency of 16 KHz. It is an electronic system for the control of separately excited motors.

The armature and field are separately controlled by the system and so the current flowing in the field is not the same as that flowing through the armature.

No starting contactors: the armature and the field are controlled directly by MOSFET. The high commutation frequency of the MOSFETs, the separately excited motor connected to the COMBI controller make it possible to maintain the same speed even under load: A) Demand for higher torque B) Higher current draw from the motor Control also the lifting pump motor as standard.

Control of a series of solenoid valves (SOLENOID CONTROL VALVE) for directional control of the hydraulic oil flow and lowering control by way of a proportional valve.

This system includes only one power contactor.

TECHNICAL SPECIFICATIONS FOR THE DRIVE MOTOR AND THE PUMP MOTOR -

Operating voltage 24 Volt Maximum field current (drive motor) 50 A Maximum armature current (drive motor) 200-400 A Armature commutation frequency 16 KHz Field commutation frequency 1 KHz Minimum ambient temperature -30 °C Maximum ambient temperature +80 °C Maximum current (pump motor) 250-300 A

3.1 MOTOR CURRENT ABSORPTION TABLE

http://www.yaleaxcessonline.com/lib/service/itwservice/272486700/Y_naen/c1a.htm (3 of 17)22.02.2012 15:46:20

http://www.yaleaxcessonline.com/lib/service/itwservice/272486700/Y_naen/c1a.htm

3.2 FUNCTIONAL CHARACTERISTICS OF THE COMBI CONTROLLER - Speed control - Excellent sensitivity at low speeds - Speed reduction: maximum speed in both directions can be adjusted using the programming console.

- Regenerative braking, based on deceleration ramps, and braking on release, on reversal and on partial release of the throttle.

- Speed control in descent: the motor speed follows the butterfly throttle control and regenerative braking is automatically activated if the motor exceeds the desired speed, thus making for optimum control on inclines.

- Hill starts with no roll-back even without using an electric brake.

- Antiroll-down function with keyswitch ON; the controller monitors the speed of the drive motor, and if the drive motor is found to be running in standby conditions, the controller activates the brake and controls the descent at very low speed.

- High motor and battery efficiency thanks to the high commutation frequency - Control of hydraulic functions with actuator speeds individually programmable and possibility to use proportional controls.

- Lowering control by proportional valve (can be replaced by ON/OFF valve).

Use of a proportional valve allows starting and stopping with controlled acceleration and deceleration ramps.

- Parameter editing via digital console (see specific description) - Internal hour counter (can be displayed on console) - Log of last 5 alarms with relative hour counter and temperature displayed on the console - Tester function on digital console to display the main parameters and characteristics of the machine - If the main contactor is out of service for more than one minute, it automatically returns to rest position; on selecting drive or operating the tiller, the contactor resets; on power up, it remains open until until either the drive control or the tiller switch is open.

3.3 SCHEMATIC DIAGRAM

3.4 PROTECTION DEVICES - Connection faults: The inputs are protected against connection faults.

- Thermal protection device: If the temperature of the COMBI exceeds 80°C, the maximum current is automatically reduced in proportion to the increase in temperature The temperature can never exceed 85°C, and is displayed on the MDI or the programming console - Driver protection: The drivers are protected against all possible short circuits. http://www.yaleaxcessonline.com/lib/service/itwservice/272486700/Y_naen/c1a.htm (4 of 17)22.02.2012 15:46:20

http://www.yaleaxcessonline.com/lib/service/itwservice/272486700/Y_naen/c1a.htm

- Battery discharged: When the battery is low, the maximum current is decreased in proportion to the degree to which the battery is discharged.

- Protection against accidental starts: Starting the machine requires a precise sequence of operations that, if not performed correctly, prevents starting.

The drive control must be open after the keyswitch and tiller microswitch (or dead-man microswitch if present).

- Protection against uncontrolled movements: The main contactor will not close if: - the power circuit is not functioning; - the logic circuit is not functioning perfectly.

- Main contactor: this must be installed to protect the controller against polarity reversal and for reasons of safety.

- External agents: The controller is protected against dust and splashes of liquids to an ingress protection rating of IP64.

3.5 COMBI CONTROLLER DIAGNOSTICS COMPONENT SELF-DIAGNOSIS The microprocessor runs diagnostic tests on the main components of the controller.

Diagnostic tests are structured into 4 main types.

1) Diagnostics on power-up : watch dog test, current sensor test, VMN test, contactor driver test, test for presence of drive request, accelerator high test.

2) Diagnostics in standby comprising: VMN test, contactor driver test, current sensor test.

3) Diagnostics during travel comprising: VMN test, current test, contactor control test, VMN in total conduction test.

4) Permanent diagnostics: temperature control, battery charge status control.

On the programming console it is possible to display the message relative to the alarm in progress.

3.6 OPERATING PRINCIPLE OF THE COMBI CONTROLLER Basic motor power supply circuit.

- As can be seen in the diagram on the right, the field and the armature are controlled by two separate circuits. The field is powered by a mosfet circuit designated “H-circuit” in which the mosfets are activated in pairs according to the selected direction of travel.

- circuit when drive is not selected

- The diagram on the right shows how the mosfet circuit activated for forward travels.

http://www.yaleaxcessonline.com/lib/service/itwservice/272486700/Y_naen/c1a.htm (5 of 17)22.02.2012 15:46:20