DOWNLOAD PDF Volvo Penta 16 Liter(EMS 2) Generating Set & Industrial Engines Operator's Manual

OPERATOR’S MANUAL Generating set and industrial engines 16 liter (EMS 2)

Foreword Volvo Penta industrial engines are relied upon throughout the world, in both mobile and stationary applications, under some of the most rigorous conditions imaginable. This is not by chance.

After more than 90 years of producing engines the name Volvo Penta has come to symbolize reliability, technical ingenuity, first-class performance and longevity. We believe that these characteristics are also ultimately your requirements and expectations for new Volvo Penta industrial engines.

To make certain that your expectations are matched, we ask that you read carefully through the instruction book before starting the engine.

Sincerely 7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:32

AB VOLVO PENTA

Engine data Engine designation ...........................

Product number ....................................

Serial number .........................................................................................................

Clutch, type/nr. .......................................................................................................

Nearest Volvo Penta service location Name ..........................................................................

Telephone ....................

Address ...................................................................................................................

© 2005 AB VOLVO PENTA Volvo reserves the right to make changes Printed on environmentally friendly paper

Table of contents Safety information ................................................. 2 Safety rules for operation and maintenance .......... 3

Troubleshooting .................................................. 25 Symptoms and possible causes ......................... 25

Introduction ........................................................... 6 Environmental responsibility ................................. 6 Running in ............................................................. 6 Fuel and oils ......................................................... 6 Maintenance and spare parts ................................ 6 Certified engines ................................................... 7

Maintenance schedule ........................................ 26 Maintenance schedule ........................................ 26

7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:32

Introduction ........................................................... 8 Technical description ............................................ 8 Identification numbers ......................................... 10 EMS 2 ................................................................ 11 Instruments EMS 2 ............................................. 12 DCU (Display Control Unit) .................................. 13 Starting the engine .............................................. 19 Before starting ................................................... 19 Starting method EMS 2 ...................................... 20 Starting in extreme cold ..................................... 21 Never use start spray ......................................... 22 Starting with auxiliary batteries .......................... 22 Operation ............................................................. 23 Checking instruments ........................................ 23 Fault indication ................................................... 23 Operation at low load ......................................... 23 Stopping the engine ........................................... 24 Before stopping .................................................. 24 Stop ................................................................... 24 After stopping .................................................... 24 Extra stop ........................................................... 24

Maintenance ........................................................ 28 Engine, general ................................................... 28 Lubrication system ............................................... 31 Cooling system ................................................... 34 Fuel system ........................................................ 40 Electrical system ................................................ 43 Component location ............................................. 46 Laying up ............................................................. 47 Conservation ....................................................... 47 Removing conservation preparations ................... 48 Diagnostic function ............................................. 49 Diagnostic function ............................................. 49 Message regarding disturbance ........................... 49 Effect on engine .................................................. 49 Operation ............................................................ 50 Fault codes ........................................................... 52 Technical data ..................................................... 61 General ............................................................... 61 Lubrication system .............................................. 62 Fuel system ........................................................ 63 Cooling system ................................................... 64 Electrical system ................................................ 64

1

Safety information Read this chapter very carefully. It has to do with your safety. This describes how safety information is presented in the instruction book and on the product. It also gives you an introduction to the basic safety rules for using and looking after the engine.

7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:32

Check that you have received the correct instruction book before you read on. If not, please contact your Volvo Penta dealer.

Incorrect operation can lead to personal injury and damage to products or property. So read the instruction book through very carefully before you start the engine or do any maintenance or servicework. If there is still something which is unclear or if you feel unsure about it, please contact your Volvo Penta dealer for assistance.

This symbol is used in the instruction book and on the product, to call your attention to the fact that this is safety information. Always read such information very carefully.

Safety texts in the instruction book have the following order of priority: WARNING! Warns for the risk of personal injury, major damage to product or property, or serious malfunctions if the instruction is ignored.

IMPORTANT! Is used to call attention to things which could cause damage or malfunctions to product or property.

NOTE! Is used to call attention to important information, to facilitate work processes or operation.

This symbol is used on our products in some cases and refers to important information in the instruction book. Make sure that warning and information symbols on the engine are clearly visible and legible. Replace symbols which have been damaged or painted over.

2

Safety information

Safety rules for operation and maintenance Daily checks Make it a habit to always give the engine and engine bay a visual check before operation (before the engine is started) and after operation (when the engine has been stopped). This helps you to quickly discover whether any leakage of fuel, coolant, oil or any other abnormal event has happened, or is about to happen.

Ignition lock If the instrument panel does not have a key switch, the engine room must be lockable, to prevent unauthorized persons from starting the engine. Alternatively, a lockable main switch can be used.

Care and maintenance Fuel filling There is always a risk of fire and explosion during fuel filling. Smoking is not permissible, and the engine should be stopped.

7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:32

Never over-fill the tank. Shut the tank cap securely.

Only use the fuel recommended in the instruction book. The wrong grade of fuel can cause malfunctions or stop the engine. In a diesel engine, it can also cause the injection pump to bind and the engine will over-rev, entailing a strong risk of personal injury and machinery damage.

Knowledge The instruction book contains instructions for doing the most common service and maintenance tasks in a safe and correct manner. Read them carefully before starting work.

Literature for more major tasks is available from your Volvo Penta dealer.

Never do a job if you are not entirely sure about how to do it. Please contact your Volvo Penta dealer and ask for assistance instead.

Stop the engine.

Carbon monoxide poisoning Only start the engine in a well- ventilated area. When operated in a confined space, exhaust fumes and crankcase gases must be ventilated.

Operation The engine must not be operated in environments which contain explosive media since none of the electrical and mechanical components are explosion proof.

Going close to a running engine is a safety risk. Hair, fingers, loose clothes, or dropped tools can catch on rotating components and cause severe injury.

Stop the engine before opening or removing the engine hatch/hood. Care and maintenance work should be done with the engine stopped unless otherwise specified.

Prevent the engine from being started by cutting the current with the battery isolator, or remove the cable from the battery positive pole before you start service work. Fix a notice by the operator’s seat to say that work is in progress.

Working with, or going close to a running engine is a safety risk. Hair, fingers, loose clothes, or dropped tools can catch on rotating components and cause severe injury. Volvo Penta recommends that all service work which requires the engine to be running should be done by an authorized Volvo Penta workshop.

When engines are supplied without touch guards, all rotating components and hot surfaces must be protected after installation in their application, if necessary for personal safety.

3

Safety information

Safety rules for operation and maintenance (contd.)

Lifting the engine

Batteries

The existing lugs on the engine should be used for lifting. Always check that the lifting devices are in good condition and that they have the correct capacity for the lift (engine weight together with auxiliaries, if fitted). The engine should be lifted with an adjustable lifting boom for safe handling. All chains or cables should be parallel to each other and should be as square as possible to the top of the engine. Please note that auxiliary equipment installed on the engine could change its center of gravity. Special lifting devices may then be needed to obtain the correct balance and safe handling. Never do any work on an engine which just hangs from a liftingdevise.

Batteries contain and give off an explosive gas, especially when charged. This gas is very flammable and highly explosive.

7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:32

Before starting

Smoking, open flames or sparks must never occur in or near to batteries or the battery locker.

Incorrect connection of a battery cable or start cable can cause a spark which can be sufficient, in its turn, to make the battery explode.

Start spray Never use start spray or similar preparations to help in starting an engine with air pre-heating (glow plugs / starting heater). They may cause an explosion in the inlet manifold. Danger of personal injury.

Re-install all guards which have been removed during service work, before re-starting the engine. Make sure that there are no tools or other objects left behind on the engine.

Hot surfaces and fluids

Never start a turbocharged engine without the air filter in place. The rotating compressor turbine in the turbocharger can cause severe injury. There is also a risk that foreign bodies could be sucked in and cause machinery damage.

A hot engine always offers the risk of burns. Be on your guard against hot surfaces: the exhaust manifold, turbocharger, oil pan, charge air pipe, starting heater, hot coolant and hot lubricating oil in pipes, hoses etc.

Fire and explosion Fuel and lubrication oil All fuel, most lubricants and many chemicals are flammable. Always read and observe the advice on the packages.

Work on the fuel system must be done with the engine cold. Fuel leakage and spills on hot surfaces or electrical components can cause fires.

Store oil and fuel soaked rags and other flammable material in a fire-proof manner. Oil soaked rags can self-ignite in certain circumstances.

Chemicals Most chemicals, such as glycol, rust preventer, conservation oils, degreasers etc. are hazardous. Always read and observe the advice on the packages.

Some chemicals, such as conservation oils, are flammable and alsohazardous to breathe. Ensure good ventilation and use a protective mask for spraying. Always read and observe the advice on the packages.

Store chemicals and other hazardous material out of the reach of children. Hand in surplus or used chemicals to a recycling station for destruction.

Never smoke when filling fuel, lubrication oil or when close to fuel filling stations or the engine bay.

Lubrication system Non-original spare parts Components in fuel systems and electrical systems on Volvo Penta engines are designed and manufactured to minimize the risk of explosions and fire, in accordance with applicable legal requirements.

The use of non-original spare parts can cause an explosion or fire.

4

Hot oil can cause burns. Avoid skin contact with hot oil.

Make sure that the oil system is de-pressurized before starting work. Never start or run the engine with the oil filler cap removed, because of the risk of oil spillage.

Safety information

Cooling system

Electric welding

Avoid opening the coolant filling cap when the engine is hot. Steam or hot coolant can spray out at the same time as the pressure built up is lost.

Remove the positive and negative cables from the batteries. Then disconnect all cables connected to the alternator.

If the filler cap, coolant hose etc., still has to be opened or removed when the engine is hot, undo the filler cap slowly and carefully, to let the pressure out before removing the filler cap completely and starting work. Note that the coolant can still be hot and cause scalding.

Disconnect both connectors from the engine control module.

Fuel system Always protect your hands when searching for leaks.

Fluids which leak under pressure can force their way into body tissue and cause severe injury. There is a risk of blood poisoning (septicemia).

Always connect the welder earth clamp to the component to be welded, and as close as possible to the weld site. The clamp must never be connected to the engine or in such a way that current can pass through a bearing.

When welding is completed: Always connect the alternator cables to the alternator and the connectors to the engine control module before the battery cables are put back.

7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:32

Always cover the alternator if it is located beneath the fuel filters. Fuel spillage can damage the alternator.

Electrical system Cut the current Before any work is done on the electrical system, the engine must be stopped and the current cut by switching off the main switch(es). External current supply for engine heaters, battery chargers or other auxiliary equipment connected to the engine must be disconnected.

Batteries Batteries contain a highly corrosive electrolyte. Protect your eyes, skin and clothes during charging and other handling of batteries. Always use protective goggles and gloves.

If acid comes into contact with your skin, wash at once with soap and a lot of water. If you get battery acid in your eyes, flush at once with a lot of cold water, and get medical assistance at once.

5

Introduction This instruction book has been prepared to give you the greatest possible benefit from your Volvo Penta industrial engine. It contains the information you need to be able to operate and maintain the engine safely and correctly.

Please read the instruction book carefully and learn to handle the engine, controls and other equipment in a safe manner before you start the engine.

IMPORTANT! This instruction book describes the engine and equipment sold by Volvo Penta. Variations in appearance and function of the controls and instruments may occur in certain variants. In these cases, please refer to the instruction book for the relevant application.

7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:32

Environmental responsibility All of us want to live in a clean, healthy environment, where we can breathe clean air, see healthy trees, have clean water in lakes and seas, and be able to enjoy the sunlight without fearing for our health. Unfortunately, this is not self-evident these days, it is something all of us must work for.

When an opening clutch is installed, this should be checked more carefully during the first days. Adjustment may need to be done to compensate bedding in of the friction plates.

As an engine manufacturer, Volvo Penta has particular responsibility and for this reason, environmental care is a self-evident foundation of our product development. Volvo Penta has a wide engine program these days, where considerable progress has been made in reducing exhaust fumes, fuel consumption, engine noise etc.

Only use the grades of fuels and oils recommended in the instruction book (please refer to the “Maintenance” chapter under the fuel and lubrication system headings). Other grades of fuel and oils can cause malfunctions, increased fuel consumption and eventually even shorten the life of the engine.

We hope that you will want to preserve these values.

Always observe the advice in the instruction book about fuel grades, operation and maintenance, to avoid unnecessary environmental impact. Please contact your Volvo Penta dealer if you notice any changes such as increased fuel consumption or increased exhaust smoke.

Please remember to always hand in hazardous waste such as drained oil, coolant, old batteries etc. for destruction at an approved recycling facility.

If we all pull together, we can make a valuable contribution to the environment together.

Running in The engine must be “run in” during its first 10 hours, as follows: Use the engine in normal operation. Full load should only be applied for short periods. Never run the engine for a long period of time at constant speed during this period, this does not apply to GE engines.

Higher oil consumption is normal during the first 100200 hours of operation. For this reason, check the oil level more frequently than normally recommended.

6

Fuel and oils

Always change the oil, oil filter and fuel filter at the specified intervals.

Maintenance and spare parts Volvo Penta engines are designed for maximum reliability and long life. They are built to withstand a demanding environment, but also to have the smallest possible environmental impact. Through regular service and use of Volvo Penta original spare parts, these qualities are retained.

Volvo Penta has a world-wide network of authorized dealers. They are Volvo Penta product specialists, and have the accessories, original spares, test equipment and special tools needed for high quality service and repair work.

Always observe the maintenance intervals in the instruction book, and remember to note the engine/transmission identification number when you order service and spare parts.

Introduction

Certified engines If you own an emission certified engine, which is used in an area where exhaust emissions are regulated by law, it is important to be aware of the following: Certification means that an engine type has been checked and approved by the relevant authority. The engine manufacturer guarantees that all engines made of the same type are equivalent to the certified engine.

This makes special demands on the care and maintenance you give your engine, as follows: and service intervals recommended • Maintenance

by Volvo Penta must be complied with.

• Only Volvo Penta original spares may be used. to injection pumps, pump settings and in• Service jectors must always be done by an authorized

engine must not be converted or modified, ex• The cept for the accessories and service kits which Volvo Penta has developed for the engine. installation changes to the exhaust pipe and • No engine air inlet ducts may be done. seals may be broken by unauthorized person• No nel.

The general advice in the instruction book about operation, care and maintenance applies.

IMPORTANT! Delayed or inferior care/maintenance, and the use of non-original spares,parts means that AB Volvo Penta can no longer be responsible for guaranteeing that the engine complies with the certified version.

Damage, injury and/or costs which arise from this will not be compensated by Volvo Penta.

7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:32

Volvo Penta workshop.

Warranty Your new Volvo Penta industrial engine is covered by a limited warranty, under the conditions and instructions compiled in the Warranty and Service book.

Please note that AB Volvo Penta’s liability is limited to the specification in the Warranty and Service book. Read it carefully, as soon as possible after delivery. It includes important information about warranty cards, service intervals, maintenance, which it is the responsibility of the owner to know, check and carry out. If this is not done, AB Volvo Penta may fully or partly refuse to honor its warranty undertakings.

Please contact your Volvo Penta dealer if you have not received a Warranty and Service book, or a customer copy of the warranty card.

7

Introduction TAD1640GE, TAD1641GE, TAD1642GE, TAD 1641VE and TAD1642VE are in-line, direct injected, 6-cylinder industrial diesel engines.

All engines are equipped with electronically controlled fuel management (EMS 2), turbocharger, intercooler, thermostatically controlled cooling systems and electronic speed control.

7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:32

Technical description Engine and engine block

Lubrication system

–

The engine block and cylinder head are manufactured of alloyed cast iron

–

Water cooled oil cooler

–

Gear driven oil pump

–

Seven bearing induction hardened crankshaft

–

Two full flow filters and a spin-on bypass filter

–

Wet, replaceable cylinder liners

Turbocharging system

–

Cast aluminum pistons with oil cooling

–

–

Three piston rings, with a “keystone” type top ring

Cooling system

–

Induction hardened, overhead, seven bearing camshaft with

–

Radiator with expansion tank

–

Four valves per cylinder

–

Air cooled intercooler

–

Replaceable valve seats and valve guides

–

Belt-driven water pump

–

Piston thermostat

Fuel system –

Microprocessor based fuel supply control unit (EMS 2)

–

Gear driven fuel supply pump

–

Centrally located unit injectors with electromagnetically controlled fuel valves

–

Spin-on secondary fuel filter and water trap

8

Turbocharger

Electrical system –

24 V electrical system

–

Alternator with charge sensor 80 A (110 A option)

–

Engine mounted extra stop (AUX STOP)

7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:32

Introduction

TAD1640GE, TAD1641GE, TAD1642GE TAD1641VE, TAD1642VE

9

Introduction

Identification numbers Location of engine signs

The sign above shows:

The sign above shows: A Engine designation 7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:32

B Engine power, net, (without fan) C Max. engine speed D Main software E Data set 1 F Data set 2 G Product number

Explanation of engine designation: E.g. TAD1641GE/TAD941VE T

– Turbo

A

– Air to air intercooler

D

– Diesel engine

16 – Cylinder volume, liter

10

4

– Generation

1

– Version

G

– Generator unit engine

V

– Stationary and mobile operation

E

– Emission certified

1

Engine designation

2

Serial number

3

Specification number

Introduction

EMS 2 EMS 2 (Engine Management System) is an electronic system with CAN communication (Controller Area Network) for diesel engine control. The system has been developed by Volvo Penta and includes fuel control and diagnostic function.

Summary

Fuel control

The system includes sensors, control unit and unit injectors. The sensors send input signals to the control unit, which controls the unit injectors in its turn.

The engine fuel requirement is analyzed up to 100 times per second. The amount of fuel injected into the engine and the injection advance are fully electronically controlled, via fuel valves and the unit injectors.

Input signals

7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:32

The control unit receives input signals about engine operating conditions etc. from the following components: –

coolant temperature sensor

–

charge pressure / charge temperature sensor

–

crankcase pressure sensor

–

position sensor, camshaft

–

speed sensor, flywheel

–

coolant level sensor

–

oil level and temperature sensor

–

oil pressure sensor

–

fuel pressure sensor

–

water in fuel indicator

Output signals The control module uses the input signals to control the following components: –

unit injectors

–

starter motor

–

main relay

–

pre-heating relay

This means that the engine always receives the correct volume of fuel in all operating conditions, which offers lower fuel consumption, minimal exhaust emissions etc.

Diagnostic function The task of the diagnostic function is to discover and localize any malfunctions in the EMS 2 system, to protect the engine and to ensure operation in the event of serious malfunction.

If a malfunction is discovered, this is announced by warning lamps, a flashing diagnostic lamp or in plain language on the instrument panel, depending on the equipment used. If a fault code is obtained as a flashing code or in plain language, this is used for guidance in any fault tracing. Fault codes can also be read by Volvo’s VODIA tool at authorized Volvo Penta workshops.

If there is a serious malfunction, the engine will be shut down altogether, or the control unit will reduce the power delivered (depending on application). Once again, a fault code is set for guidance in any fault tracing.

Information from the sensors provides exact information about current operation conditions and allows the processor in the control unit to calculate the correct fuel injection volume and timing, check engine status etc.

11

Introduction

Instrument, EMS 2 NOTE! All instruments are accessories.

CIU - Control Interface Unit The CIU is the “translator” between the EMS 2 control unit and the customer’s own control panel. The CIU has two serial communication links, a fast one and a slow one.

The fast one is a so-called CAN link. All data related to instruments, indication lamps, connectors and potentiometers is controlled by this link.

7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:32

The slow link manages diagnostic information for flashing codes etc.

DU - Display Unit The DU is an instrument panel which shows engine working values graphically on an LCD screen. It consists of an computerised unit for permanent installation in a control panel.

The DU is connected between the engine control unit and the CIU or DCU.

Easy Link instrument (only together with a CIU) The following “Easy Link” instruments are available: – Engine speed / hours counter (fault codes are also displayed on the tachometer display when the diagnostic button is pressed)

12

–

Coolant temperature

–

Oil pressure

–

Oil temperature

–

Battery voltage

–

Alarm panel

–

Turbo pressure

Introduction

DCU (Display Control Unit) The DCU (Diesel Control System) control panel is available as an optional accessory for the EMS (Engine Management System) electronic control system. The DCU is a digital instrument panel which communicates with the engine control unit. DCU has several functions, such as: engine control, monitoring, diagnostics and parameter setting.

The menus in the DCU system can be used to check, and in some cases to set a number of different functions in the EMS system.

NOTE! The menus and illustrations shown here are the English version. The language can be changed, however.

Please refer to the “Setup” menu.

7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:32

10

9

8

7

1

2

3

4

5

6

1. LED display

6. ON/OFF. Starts and stops the system

2. START. Starts the engine

7. Scroll downwards in menus

3. SPEED -. Reduces engine speed

8. SEL. Selects in menus

4. SPEED +. Increases engine speed

9. Scroll upwards in menus

5. STOP. Stops the engine

10. ESC. Return to previous menu selection

Start When the DCU panel is started up, the “Engine Data” menu is displayed. Press “ESC” to come to the main menu.

13

Introduction

Menus There are several sub-menus under each main menu.

There is not space for all the menu choices on the display. To scroll through the menus, use the “7” and “9” buttons on the display. Press the “SEL” button, no.

“8” to make a selection. Please refer to the illustration on the previous page.

NOTE! The “Setup” menu can be used to select the language that you want to use on the display.

Main menu n Engine data, relevant engine data. n Preheat, manual activation of pre-heating n Governor mode, activation of droop. n Diagnostics, shows fault codes in plain language.

7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:32

n Trip reset, resets trip data n Setup, parameter setting n Information, shows the data for the applicable hardware, software, data set and engine identification of the engine and DCU

Engine data shows relevant engine data.

14

•

Engine speed, can be controlled with the “SPEED +” and “SPEED –” buttons (rpm)

•

Charge pressure (kPa)

•

Coolant temperature (°C)

•

Charge air temperature (°C)

•

Oil pressure (kPa)

•

Oil temperature (°C)

•

Engine hours (h)

•

Battery voltage (V)

•

Fuel consumption (l/h)

•

Instantaneous fuel consumption (trip fuel) (l)

Introduction

Preheat manual activation of pre-heating. When it is activated, the EMS system senses when started if pre-heating is needed. For automatic pre-heating, please refer to the “Setup” / “Pre-heat on ignition” menu.

The pre-heating time is adjusted to suit the engine temperature, and can last for up to 50 seconds both before and after starting. Also refer to “Starting procedure, EMS 2”.

•

Press “SEL”, the text “Preheat requested” is displayed.

•

The display automatically returns to the “Engine Data” menu.

7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:32

Governor mode activates/shuts off droop. To set the droop level, please refer to the “Setup” / “Governor gradient” or “Governor droop” menus.

•

Select “Isochronous mode” or “Droop mode” with the SEL button.

Diagnostics shows the error list containing the 10 latest active and inactive faults. The fault code are shown as text on the display.

•

Scroll through the error list with the arrow keys.

Trip reset resets trip data, such as fuel consumption.

•

Press the SEL button to reset trip data.

15

Introduction

Setup parameter setting in the engine’s control systems. Different menus appear under “Customer parameter”, depending on whether you select “Versatile” or “Genset” from “Set application”.

7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:32

The parameters that can be set / selected (choice is made with the SEL button) are: •

Set application, setting of “Versatile” or “Genset”.

Different menus appear under “Customer parameter”, depending on what is chosen here.

•

Unit, selection of units of measurement (metric or US units)

•

Language, selection of the language shown in the display. You can choose between English, French, German and Spanish.

•

Stop energized to, setting for the external stop input. Activated at “Stop” or “Run”.

“Stop”: The stop input must be connected to voltage to stop the engine.

“Run”: The stop input must be connected to voltage to run the engine.

•

Customer parameter, alarm limit setting. Please refer to “Customer parameter / Versatile” and “Customer parameter / Genset”.

•

Throttle input setting, setting of speed control and voltage limits. See “Throttle input setting”.

•

Display setting, display setting. See “Display setting”.

Customer parameter / Versatile

16

•

Idle engine speed - setting idling speed

•

Preheat on ignition - activation of automatic preheating. The engine control system senses if preheating is needed and activates it directly when switched on.

•

Governor gradient (Nm/rpm) - setting the droop level, when this has been activated. Please refer to “Governor droop” in the main menu for activation.

•

Oil temp warning limit (°C) - setting the alarm limit for the oil temperature.

•

Coolant temp warning limit (°C) - setting the alarm limit for the coolant temperature.

Introduction

7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:32

Customer parameter / Genset •

Primary engine speed - selection of engine speed, 1500 or 1800 rpm.

•

Preheat on ignition - activation of automatic preheating. The engine control system senses if preheating is needed and activates it directly when switched on.

•

Governor droop (%) - setting the droop level, when this has been activated. Please refer to “Governor droop” in the main menu for activation.

•

Overspeed limit (%) - setting the speed for the excess speed alarm, % of set engine speed.

•

Overspeed shutdown - activation of engine shut down when the excess speed alarm is activated.

Please refer to “Overspeed limit” to activate the alarm limit for the excess speed alarm.

•

Oil temp warning limit (°C) - setting the alarm limit for the oil temperature.

•

Coolant temp limit (°C) - setting the alarm limit for the coolant temperature.

Throttle input setting speed control setting (throttle operation).

•

Set throttle mode “OFF” - engine speed is controlled via the DCU panel. “ext throttle input” - engine speed is controlled with a potentiometer (accelerator). “ext voltage input” - engine speed is controlled by an external unit.

•

Set idle voltage (V) - setting the voltage level at idle.

•

Set max voltage (V) - setting the voltage level at maximum speed.

Potentiometer value (%)

Potentiometer value (%)

100

100

0

0 Voltage (V) Idling

Max

Voltage (V) Max

Idling

17

Introduction

Display setting

7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:32

settings for the display. Adjustment is done with the “7” and “9” buttons, please refer to the DCU panel in the illustration.

•

Set contrast (%) - display contrast adjustment.

•

Set backlight time (sec) - sets the time (in seconds) for background illumination in the display.

The light is then switched off if the panel is not used.

•

Set backlight brightness - adjustment of illumination strength in the display.

Information shows the data for the engine and DCU.

18

•

Engine hardware ID - part number of the engine control module

•

Engine software ID - part number of the software in the engine control module

•

Engine dataset1 ID - part number of engine data set 1.

•

Engine dataset2 ID - part number of engine data set 2.

•

Vehicle ID - chassis number

•

DCU hardware ID - part number of the DCU.

•

DCU software ID - part number of the software in the DCU.

•

DCU dataset1 ID - part number of DCU data set 1.

•

DCU dataset2 ID - part number of DCU data set 2.

Starting the engine Make it a habit to give the engine and engine bay a visual check before starting. This will help you to discover quickly if anything abnormal has happened, or is about to happen. Also check that instruments and warning displays show normal values after you have started the engine.

WARNING! Never use start spray or similar products as a starting aid. Explosion risk!

Before starting that the oil level is between the MAX and • Check MIN marks. Please refer to the “Maintenance, lubrication system” chapter:

7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:32

• Open the fuel taps. that no leakage of oil, fuel or coolant• Check occurs.

the coolant level and that the radiator is not • Check blocked externally. Please refer to the “Maintenance, cooling system” chapter.

WARNING! Do not open the filler cap (1) when the engine is hot. Steam or hot fluid could spray out.

NOTE! Only open filler cap (1). Do not open filler cap (2).

• Turn the main switch(es) on.

IMPORTANT! Never disconnect the current with the main switch(es) when the engine is running.

This can damage the alternator. the engine speed control to idle, and release • Move the opening clutch/gearbox if installed.

19

Starting the engine

Starting method EMS 2 The pre-heating time is adjusted to suit the engine temperature, and can last for up to 50 seconds both before and after starting.

The starter motor connection time is maximized to 30 seconds. After that, the starter motor circuit is cut for 80 seconds to protect the starter motor against overheating.

NOTE! Preheating must be activated at temperattures below 0°.

9

7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:32

7

6

2 With pre-heating 1. Depress the “ON/OFF” button (6).

2. Press the “SEL” button (7) to come to the main menu.

3. Scroll down to Preheat with button (9). Press the “SEL” button (7).

4. In the pre-heat menu, press the “SEL” button (7) to select pre-heating. The text “Preheat active please wait” is shown in the display.

5. Wait until the text has gone out and then press the “START” button (2).

Without pre-heating 1. Depress the “ON/OFF” button (6).

2. Press the “START” button (2).

Leave the engine to idle for the first 10 seconds. Then warm the engine up at low speed and under low load.

IMPORTANT! Never race the engine when it is cold.

20

Starting the engine

Starting in extreme cold Certain preparations must be made to facilitate engine starting, and in some cases to make starting possible at all.

Use a winter grade fuel (of a well-known make) which has been approved for the relevant temperature. This reduces the risk of wax deposits in the fuel system.

At extremely low temperatures, the use of a fuel heater is recommended.

For fully acceptable lubrication, a synthetic engine oil of recommended viscosity for the relevant temperature should be used. Please refer to the “Maintenance, lubrication system” chapter: Synthetic lubricants are able to manage a wider temperature range than mineral-based lubricants.

7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:32

Pre-heat the coolant with a separately installed electric engine heater. In extreme cases, a diesel-burning engine heater may be needed. Ask your Volvo Penta dealer for advice.

IMPORTANT! Make sure that the cooling system is filled with a glycol mixture. Please refer to the “Maintenance, cooling system” chapter: The batteries should be in good condition. Cold weather reduces battery capacity. Increased battery capacity may be necessary.

21

Starting the engine

Never use start spray WARNING! Never use start spray or similar products as a starting aid. They may cause an explosion in the inlet manifold. Personal injury could also be caused.

Starting with auxiliary batteries WARNING! Batteries (especially auxiliary batteries) contain hydrogen which is highly explosive in contact with air. A spark, which can be formed if the auxiliary batteries are wrongly connected, is enough to make a battery explode and cause damage.

7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:32

1. Check that the auxiliary batteries are connected (series or parallel) so that the rated voltage corresponds to the engine system voltage.

2. First connect the red (+) jumper cable to the auxiliary battery, then to the flat battery. Then connect the black (–) jumper cable to the auxiliary battery, and lastly to a place which is some distance away from the flat batteries, e.g. at the mainswitch on the negative cable or the negative cable terminal on the starter motor.

3. Start the engine.

WARNING! Do not move the connections when you attempt to start the engine (risk of arcing), and do not stand and lean over one of the batteries.

4.

Remove the jumper cables in the reverse order from installation.

WARNING! The ordinary cables to the standard batteries must not be loosened on any condition.

22

Operation Correct operation technique is very important for both fuel economy and engine life. Always let the engine warm up to normal operating temperature before operating at full power. Avoid sudden throttle openings and operation at high engine speeds.

Checking instruments

Operation at low load

Check all instruments directly after starting, and then regularly during operation.

Avoid long-term operation at idle or at low load, since this can lead to increased oil consumption and eventually to oil leakage from the exhaust manifold, since oil will seep past the turbocharger seals and accompany the induction air into the inlet manifold at low turbo boost pressure.

IMPORTANT! On engines which operate continuously, the lubrication oil level must be checked, at least every 24 hours. Please refer to the “Maintenance, lubrication system” chapter.

7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:32

Fault indication If the EMS 2 system receives abnormal signals from the engine, the control unit generates fault codes and alarms, in the form of lamps and audible warnings.

This is done by means of CAN signals to the instrument.

More information about fault codes and fault tracing is found in the “Diagnostic function” chapter.

One consequence of this is that carbon builds up on valves, piston crowns, exhaust ports and the exhaust turbine.

At low load, the combustion temperature is so low that full combustion of the fuel can not be ensured, which means that the lubrication oil can be diluted by diesel fuel, and the exhaust manifold will eventually leak oil.

If the following points are done as a complement to normal maintenance, there will be no risk of malfunctions caused by operation at low load.: operation at low load to a minimum. If the • Reduce engine is regularly test run without load once a week, operation duration should be limited to 5 minutes. the engine at full load for about 4 hours once • Run a year. Carbon deposits in the engine and exhaustpipe can then be burned off.

23

Stopping the engine During longer breaks in operation, the engine must be warmed up at least once every fortnight. This prevents corrosionattack in the engine. If you expect the engine to be unused for two months or more, it must be laid up: Please refer to the chapter entitled “Laying up”.

IMPORTANT! If there is a risk of frost, the coolant in the cooling system must have sufficient frost protection. Please refer to the “Maintenance, cooling system” chapter: A poorly charged battery can freeze and burst.

Before stopping

7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:33

Let the engine run for a few minutes without loading before stopping it. This permits the temperature inside the engine to even up, “after-boiling” is avoided, at the same time as the turbocharger cools somewhat. This contributes to long service life without malfunctions.

Stop

• Disengage the clutch (if possible).

• Depress the “STOP” button (7).

7

After stopping

• Check the engine and engine bay for leakage. off the main switches before any long stop• Turn page. out maintenance in accordance with the • Carry schedule.

Extra stop The extra stop device (AUX STOP) is located on the right side of the engine above the control unit, please refer to “Component location”.

WARNING! Working with, or going close to a running engine is a safety risk. Watch out for rotating components and hot surfaces.

24

Troubleshooting A number of symptoms and possible causes of engine malfunctions are described in the table below. Always contact your Volvo Penta dealer if any problems occur which you can not solve by yourself.

WARNING! Read through the safety advice for care and maintenance work in the chapter entitled “Safetyinformation” before you start work.

Symptoms and possible causes

7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:33

The diagnosis button lamp flashes.

Please refer to the “Diagnostic information” chapter

Engine can not be stopped.

2, 5

Starter motor does not rotate

1, 2, 3, 4, 5, 6, 7, 24

Starter motor rotates slowly

1, 2

Starter motor rotates normally but engine does not start

8, 9, 10, 11,

Engine starts but stops again

8, 9, 10, 11, 13

Engine does not reach correct operating speed at full throttle

9, 10, 11, 12, 13, 21, 25, 26

Engine runs roughly

10, 11

High fuel consumption

12, 13, 15, 25

Black exhaust smoke

12, 13

Blue or white exhaust smoke

15, 22

Too low lubrication oil pressure

16

Excessive coolant temperature

17, 18, 19, 20

Too low coolant temperature

20

No, or poor charge

2, 23

1.

Flat batteries

10. Air in the fuel system

16. Too low oil level

2.

Poor contact/open circuit in cables

11. Water/contamination in fuel

17. Coolant level too low

12. Faulty unit injector

18. Air in the coolant system

3.

Main switch turned off Main circuit breaker faulty

5.

Faulty ignition lock

6.

Faulty main relay

7.

Faulty starter motor/solenoid

8.

Lack of fuel: – fuel taps closed – fuel tank empty/wrong tank connected

13. Insufficient air supply to engine: – blocked air filter – air leakage between turbocharger and engine inlet pipe.

– fouled compressor section in turbocharger – faulty turbocharger – poor engine bay ventilation

19. Faulty circulation pump

4.

9.

Blocked fuel filter/pre-filter (because of contamination, or paraffin fraction separation in fuel at low temperature).

14. Excessive coolant temperature

20. Defective thermostat 21. Blocked intercooler 22. Too high oil level 23. Alternator drive belt slips 24. Water entry into engine 25. High back pressure in exhaust system 26. Break in “ Pot+ ” cable to pedal

15. Too low coolant temperature

25

Maintenance schedule General Your Volvo Penta engine and its equipment are designed for high reliability and long life. It is built so as to have minimal environmental impact. If given preventive maintenance, according to the maintenance schedule, and if Volvo Penta original spares are used, these properties are retained and unnecessary malfunctions can be avoided.

MAINTENANCE SCHEDULE WARNING! Before you start to do any maintenance work, read the “Maintenance” chapter carefully. This contains instructions for doing work in a safe and correct manner.

IMPORTANT! When both operation and calendar time are specified, do the maintenance job at the interval which is reached first. Maintenance points marked must be done by an authorized Volvo Penta workshop

7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:33

Daily, before first start

• Engine and engine bay, general inspection .................................................. page 28 • Oil level, checking and filling ........................................................................ page 32 • Coolant, checking level ................................................................................ page 36 Every 50 hours / at least every 12 months.

• Primary fuel filter. Drain water/contamination ............................................... page 41 After the first 150 hours

• Engine oil, changing .................................................................................. page 32 1)

1)

NOTE! An oil change is recommended, change the oil to a grade recommended by Volvo Penta.

Every 50-600 hours / at least every 12 months.

• Engine oil, changing .................................................................................. page 32 • Oil filter/By-pass filter, change .................................................................. page 32 • Primary fuel filter, change ............................................................................ page 41 • Fuel filter, changing ...................................................................................... page 41 1)

2)

1) 2)

Oil change intervals vary, depending on oil grade and sulfur content of the fuel. page 26.

Change the filters during each oil change.

Every 400 hours / at least every 12 months.

• Fuel tank (sludge trap), drain. ..................................................................... not shown • Drive belts, inspection .................................................................................. page 29 • Batteries, checking the electrolyte level ....................................................... page 44

26

Maintenance schedule

Every 800 hours / at least every 12 months.

• Charge air pipe, leakage check .................................................................... page 28 • Primary fuel filter, check ............................................................................ not shown Every 1000 hours / at least every 6 months.

• Coolant filter, changing .............................................................................. page 38 1)

1)

Not at same time as coolant change.

Every 2000 hours Turbocharger, check .................................................................................. not shown Valve clearance, inspection/adjustment ..................................................... not shown

7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:33

Every 12 months

• • • •

EMS 2-system. Inspection with diagnostic tool (VODIA) ............................. please refer to the ”VODIA User´s Guide” Engine, general inspection ........................................................................... page 28 Engine, cleaning/painting ........................................................................... not shown Air filter, tank breather, change. ................................................................. not shown Inspection, air compressor, change. .......................................................... not shown Air filter inserts, check/change ..................................................................... page 30

Every 36 months or every 8000 hours.

• Drive belts, change .................................................................................. page 29-30 Every 48 months or every 10000 hours.

Cooling system, inspection/cleaning ....................................................... page 36, 39 Coolant, change ....................................................................................... page 36-39

Newly renovated engine: After the first 250 hours Valve clearance, adjustment ...................................................................... not shown

27

Maintenance This chapter describes how the specified maintenance points should be done. Read them carefully before starting work. The times when maintenance points need to be attended to are given in the previous chapter: Maintenance schedule WARNING! Read through the safety advice for care and maintenance work in the “Safety information” chapter before starting work.

WARNING! Care and maintenance work should be done with the engine stopped unless otherwise specified.

Make it impossible to start the engine by removing the ignition key and cutting the system voltage with the main switch. Working with, or going close to a running engine is a safety risk. Watch out for rotating components and hot surfaces.

Engine, general

General inspection 7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:33

Make it a habit to give the engine and engine bay a visual check before the engine is started and after operation, when the engine has been stopped.

This will help you to discover quickly if anything abnormal has happened, or is about to happen.

Look especially carefully at oil, fuel and coolant leakage, loose screws, worn or poorly tensioned drive belts, loose connections, damaged hoses and electrical cables. This inspection only takes a few minutes and can prevent serious malfunctions and expensive repairs.

WARNING! Deposits of fuel, oils and grease on the engine or in the engine bay are a fire hazard and must be removed as soon as they are discovered.

IMPORTANT! If you discover a leakage of oil, fuel or coolant, investigate the cause and fix the fault before you start the engine.

IMPORTANT! Remember the following when washing with a high pressure washer: Never aim the water jet at radiators, intercoolers, seals, rubber hoses or electrical components.

Charge air pipe, leakage check Check the charge air pipes, hose connections and the condition of the clamps for cracks or other damage. Change as necessary.

IMPORTANT! Torque the clamps to 9 ± 2 Nm (6.6±1.5 lbf-fot).

28

Maintenance

Drive belt / Alternator belt, inspection Inspection should be done after operation, when the belts are hot.

It should be possible to press the alternator belts and drive belts down about 3-4 mm (0,118-0,157 ") between the pulleys.

The alternator belts and drive belts have automatic belt tensioners and do not need to be adjusted. Check the condition of the drive belts. Change as necessary, please refer to “Alternator belt, change” and “Drive belt, change”.

Alternator belts, changing

7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:33

IMPORTANT! Always change a drive belt which appears worn or cracked.

1. Disconnect the main switch(es) and check that the engine is not connected to system voltage.

2. Remove the fan guard and fan ring round the cooling fan.

3. Remove the belt guard.

4. Insert a 1/2” square wrench in the belt tensioner (1). Lift the wrench up and lift the water pump drive belt off.

5. Insert a 1/2” square wrench in the belt tensioner (2). Press the wrench down and remove the alternator belts.

6. Check that the pulleys are clean and undamaged.

1

2

7. Press the 1/2” wrench in the belt tensioner (2) down and install the new alternator drive belt.

8. Lift the 1/2” wrench in the belt tensioner (2) and install the new water pump drive belt.

9. Install the belt guards.

10. Install the fan guard and fan ring round the cooling fan.

11. Start the engine and do a function check.

29

Maintenance

Drive belt, changing 1. Disconnect the main switch(es) and check that the engine is not connected to system voltage.

2. Remove the fan guard and fan ring round the cooling fan.

3. Remove the belt guard.

4. Insert a 1/2” square wrench in the belt tensioner (1). Lift the wrench and remove the drive belt.

5. Thread the drive belt round the fan and remove it.

6. Check that the pulleys are clean and undamaged.

7. Thread the new drive belt over the fan.

8. Lift the 1/2" wrench and install the new drive belt.

9. Install the belt guards.

1

10. Install the fan guard and fan ring round the cooling fan.

7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:33

11. Start the engine and do a function check.

Air filter Check/change.

The engine is equipped with electronic air filter indication.

The control unit provides an output signal which is announced as a warning on the instrument panel. The warning indicates a pressure drop in the air filter, which must then be checked and possibly changed.

NOTE! Scrap the old filter. No cleaning or re-use is permissible.

IMPORTANT! In continuous operation, the filter should be checked every 8 hours.

Driving in extremely contaminated environmentssuch as coal mines or rock crushers requires special air filters.

30

Maintenance

Lubrication system Oil change intervals can vary from 50 to 600 hours, depending on the grade of lubrication oil and the sulfur content of the fuel. Note that oil change intervals must never exceed a period of 12 months.

If you want longer oil change intervals than given in the table below, the condition of the oil must be checked by the oil manufacturers through regular oil testing.

Sulfur content in fuel, by weight

7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:33

< 0,5 % Oilgrade

0,5 – 1,0 %

> 1,0 %1)

Oil change interval, reached first in operation

VDS-3 VDS-2 and ACEA: E7 2) VDS-2 and ACEA: E5 2) VDS-2 and Global DHD-1 2) VDS-2 and API: CI-4 2) VDS-2 and API: CH-4 2)

600 h / 12 months

300 h / 12 months

150 h / 12 months

VDS and ACEA: E3 2)

400 h / 12 months

200 h / 12 months

100 h / 12 months

ACEA: E7, E5, E4 API: CI-4, CH-4, CG-4

200 h / 12 months

100 h / 12 months

50 h / 12 months

NOTE! Mineral based oil, either fully or semi-synthetic, can be used on condition that it complies with the quality requirements above.

1)

If the sulfur content is > 1.0% by weight, use oil with TBN > 15 The engine oil must fullfil both requirements. For markets outside Europe, API: CG-4 and CH-4 can be used instead of ACEA: E3.

2)

VDS = Volvo Drain Specification ACEA = Association des Constructeurs Européenne d’Automobiles API = American Petroleum Institute Global DHD = Global Diesel Heavy Duty TBN = Total Base Number

Viscosity Select the viscosity from the adjacent table, for the appropriate continuous ambient air temperature. * Refers to synthetic or semi-synthetic oils.

* Oil change volume Please refer to the “Technical Data” chapter.

31

Maintenance

Oil level, checking and filling The oil level must be inside the marked area on the dipstick and must be checked daily before the first start.

NOTE! The oil level can be read both when the engine is stationary (the STOP side of the dipstick) and with the engine running (the OPERATING side of the dipstick).

Top up with oil via the filler opening on the left side of the engine.

Check that the correct level has been achieved. If the engine is stationary, wait for a few minutes to allow the oil to run down into the oil pan.

IMPORTANT!Do not fill up above the maximum oillevel. Only use a recommended grade of oil. (please refer to previous page).

7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:33

NOTE! The oil level sensor only measures the oil level at the time when the ignition is turned on. In other words, not continually during operation.

Engine oil, changing WARNING! Hot oil and hot surfaces can cause burns.

NOTE! Topping up must be done when the engine is warm.

1. Connect the drain hose to the oil drain pump and check that no leakage can occur.

2. Pump the oil out (or remove the bottom drain plug and drain the engine oil).

Collect all the old oil and old filters, and hand them to a re-cycling station for destruction.

3. Remove the drain hose (or install the bottom drain plug).

4. Fill up with engine oil.

Change volume, please refer to the “Technical Data” chapter.

32

Maintenance

Oil filter/By-pass filter, change WARNING! Hot oil and hot surfaces can cause burns.

1. Clean the oil filter bracket (2).

2. Remove all oil filters with a suitable oil filter remover (1).

3. Clean the mating surface of the oil filter bracket.

Make sure that no pieces of old oil seal are left behind. Carefully clean round the inside of the protective rim (2) on the oil filter bracket.

4. Put a thin layer of engine oil on the seal rings of the new fuel filters.

5. Install the new oil filters. Tighten the two full-flow filters (on the right of the illustration) ½ - ¾ turns after they just touch. Tighten the bypass filter ¾ 1 turn after it just touches.

2

7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:33

6. Top up with engine oil, start the engine and let it run for 20-30 seconds.

1

7. Shut the engine off, check the oil level and top up engine oil as necessary.

8. Check sealing round the oil filters.

33

Maintenance

Cooling system The cooling system ensures that the engine operates at the correct temperature. It is a closed circuit system and must always be filled with a mixture of at least 40 % concentrated coolant and 60 % water to protect against internal corrosion, cavitation and damage caused by freezing.

We recommend that you use “Volvo Penta Coolant, Ready Mixed”, alternatively “Volvo Penta Coolant” (concentrated) mixed with pure water according to spec, see “Coolant. Mixture”. Only coolant of this quality is suited too and approved by Volvo Penta.

The coolant should contain ethylene glycol of a good quality with a suitable chemical consistency for an adequate protection of the engine. Using anti-corrosion aditive exclusively is not permitted in Volvo Penta’s engines. Never use water by itself as coolant.

IMPORTANT! Coolant, with a sutiable consistency, must be used all year round. This applies even if there is never any risk for frost , to ensure that the engine has an adequate protection against corrosion.

Future warranty claims on the engine and additional equipment may be rejected if an unsuitable coolant has been used or if the instructions concerning coolant mixing have not been followed.

7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:33

NOTE: The anti-corrosive agents become less effective after a time, which means that the coolant must be replaced, see “Service schematic”. The cooling system should be flushed out at the same time as the coolant is replaced, see “Cooling system. Flushing”.

“Volvo Penta Coolant” is a concentrated coolant that is to be mixed with water. It has been developed to function optimally with Volvo Penta’s engines and provides excellent protection against corrosion, cavitation and frost damage.

“Volvo Penta Coolant, Ready Mixed” is a readymixed coolant, 40% “Volvo Penta Coolant” and 60% water. This concentration protects the engine against corrosion, cavitation damage and freezing conditions down to -28 °C (18°F).

34

Maintenance

Coolant. Mixture WARNING! All glycol is hazardous and harmful to the environment. Do not consume!

Glycol is flammable.

IMPORTANT! Ethylene glycol must not be mixed with other types of glycol.

Mix: 40 % “Volvo Penta Coolant” (conc. coolant) 60 % water

7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:33

This mixture protects the engine against internal corrosion, cavitation and frost damage down to -28 °C (18°F). (Using 60 % glycol lowers the freezing point to -54 °C (65°F)). Never mix more than 60 % concentrate (Volvo Penta Coolant) in the cooling liquid, this will give reduced cooling effect and increase the risk of overheating, and will give reduced freezing protection.

IMPORTANT! Coolant must be mixed with pure water, use distilled - de-ionized water. The water must fulfill the requirements specified by Volvo Penta, see “Water quality”.

IMPORTANT! It is extremely important that the correct concentration of coolant is added to the system. Mix in a separate, clean vessel before adding into the cooling system. Ensure that the liquids mix properly.

Water quality ASTM D4985: Total solid particles ...................................... < 340 ppm Total hardness: ............................................ < 9.5° dH Chloride ......................................................... < 40 ppm Sulfate ........................................................... < 100 ppm pH value ........................................................

5,5– 9

Silica (acc. ASTM D859) .............................. < 20 mg SiO2/l Iron (acc. ASTM D1068) .............................. < 0.10 ppm Manganese (acc. ASTM D858) ................... < 0.05 ppm Conductivity (acc. ASTM D1125) ................ < 500 µS/cm Organic content, CODMn (acc. ISO8467) .... < 15 mg KMnO4/l

35

Maintenance

Coolant, inspection WARNING! Do not open the filler cap (1) when the engine is warm, except in emergencies.

Steam or hot fluid could spray out.

NOTE! Only open filler cap (1). Do not open filler cap (2).

The coolant level must be higher than the MIN marking. Check the coolant level daily before starting. Top up with coolant as necessary, please refer to Coolant, filling.

7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:33

Cooling system, filling WARNING! Do not open the filler cap (1) when the engine is warm, except in emergencies.

Steam or hot fluid could spray out.

NOTE! Do not open filler cap (2).

Filling a completely empty system 1. Open filler cap (1).

2.

Check that all drain points are closed.

NOTE! Only use the coolant recommended by Volvo Penta.

3.

Mix the correct amount of coolant in advance, to ensure that the cooling system is completely filled.

4.

Fill up with coolant, so that the level ends up between the MIN and MAX markings. Do not start the engine until the system is vented and completely filled.

Filling should be done with the engine stationary.

Fill up slowly, to allow the air to flow out.

5.

Start the engine when the cooling system has been completely filled and vented. Open any venting taps some while after starting, to allow shut-in air to escape.

If a heating unit is connected to the engine cooling system, the heat control valve should be opened and the installation vented during filling.

6.

36

Stop the engine after about an hour and check the coolant level. Top up as necessary.

Maintenance

Coolant. Draining.

The engine must be stopped before draining, and the fillercap unscrewed.

WARNING! Do not open the filler cap (1) when the engine is warm, except in emergencies.

Steam or hot fluid could spray out.

NOTE! Do not open filler cap (2).On engines which are to be laid up or put in storage, the engine cooling system should not be drained. The coolant contains corrosion-inhibiting additives.

7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:33

1. Remove the filler cap (1).

2. Open all drain points. Drain the coolant from the radiator and engine block, using the drain hose. The drain nipples are situated under the radiator on the right side of the engine block.

3. Check that all coolant drains out. Deposits may be found inside the drain plug/tap, and need to be cleared away. There is otherwise a risk that coolant could remain and cause frost damage. Check whether the installation has any further taps or plugs at the lowest points of the cooling water pipes.

4. Shut any taps and check that the spring-loaded covers on the nipples close completely. Install the rubber plugs.

37

Maintenance

Intercooler. External cleaning Remove guards as necessary, to access the radiator.

Clean with water and a mild detergent. Use a soft brush. Be careful to ensure that the radiatormatrix is not damaged. Re-install the components.

7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:33

IMPORTANT! Do not use a high pressure power washer.

Coolant filter, changing

1

38

1.

Turn the tap (1) 90° to stop the flow through the coolant filter.

2.

Remove the coolant filter with a suitable extractor. Make sure that no residue from the old seal remains in the housing.

3.

Put a thin layer of engine oil on the new coolant filter seal. Screw the coolant filter on by hand until the seal comes into contact with the mating surface of the filter bracket. Then tighten the coolant filter a further 1/2 turn.

4.

Turn the tap (1) 90° to release the flow through the coolant filter again.

5.

Start the engine and do a leakage check.

6.

Switch the engine off and check the coolant level. Please refer to “Coolant level, check”.

Maintenance

Cooling system, cleaning Cooling performance is reduced by deposits in the radiator and cooling galleries. The cooling system should be cleaned out when the coolant is changed.

IMPORTANT! Cleaning must not be done if there is any risk of the cooling system freezing, since the cleaning solution does not have any frost prevention ability.

1. Empty the cooling system. Please refer to “Cooling system, draining”.

2. Put a hose into the filling hole in the expansion tank and flush with pure water, which complies with Volvo Penta specifications, please refer to the “Water Quality” chapter, until the water which runs out is completely clear.

7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:33

3. If there should still be some contamination left after flushing for a long time, cleaning can be done with coolant. Otherwise, continue as in item 8 below.

4. Fill the cooling system with 15-20% mixture of concentrated coolant. Only use Volvo Penta recommended concentrated coolant, mixed with pure water.

5. Drain the coolant after 1-2 days of operation.

NOTE! To prevent suspended material from settling back in the system, emptying should be done rapidly, within the space of 10 minutes, when the engine has not been standing still for a long time. Remove the filler cap and possibly the lower radiator hose to increase the speed of emptying.

6. Flush the system at once, very carefully, with pure hot water to stop dirt from settling on the inner surfaces again. Flush until the water that runs out is completely clean. Make sure that any heater controls are set to full heating during emptying.

7. If contamination should still be left after a long period of flushing, you can do a clean-out with Volvo Penta radiator cleaner, followed by finishing-off with Volvo Penta neutralizer. Carefully follow the instructions on the package. Otherwise, continue as in item 8 below.

8. When the cooling system is completely free from contamination, close the drain taps and plugs.

9. Fill up with Volvo Penta recommended coolant, following the instructions in the chapters entitled “Coolant, mixing” and “Coolant, filling”.

IMPORTANT! It is extremely important that the correct concentration and volume of coolant is put in the system. Mix in a separate clean vessel before filling the cooling system. Make sure that the liquids mix.

39

Maintenance

Fuel system Only use the grades of fuel recommended in the fuel specification below. Always observe the greatest cleanliness during re-fueling and work on the fuel system.

All work on the injection system of the engine must be done by an authorized workshop.

WARNING! Fire hazard. Work on the fuel system must be done with the engine cold. Fuel spills on hot surfaces or electrical components can cause fires. Store fuel-soaked rags in a fire-proof manner.

Fuel specification The fuel must at least comply with national and internationalstandards for commercially supplied fuels, such as: 7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:33

EN590 (with nationally adapted environmental and cold- requirements) ASTM D 975 No 1 - D and 2 - D JIS KK 2204 Sulfur content: Complying with legal requirements in each country. If the sulfurcontent exceeds 0.5 percent by weight, the oil changeintervals must be changed.

Please refer to the “Lubrication system” heading.

Extremely low sulfur content fuel (urban diesel in Sweden and city diesel in Finland) can cause a loss of up to 5% of power and an increase in fuel consumption of about 2–3 %.

40

Maintenance

Fuel filters, replacing NOTE! Do not fill the new fuel filter with fuel before assembly. There is a risk that contamination could get into the system and cause malfunctions or damage.

WARNING! The fuel filter must be changed when the engine is cold, to avoid the risk of fire due to spilled fuel on hot surfaces.

1. Clean round the fuel filter.

2. Remove the filter with a suitable filter remover.

Collect any spilled fuel in a collection vessel.

3. Clean the filter mating surface on the filter bracket.

4. Lubricate the seal with diesel fuel and install the new fuel filter. Tighten the fuel filter in accordance with the instructions on the fuel filter.

7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:33

5. If necessary, vent the fuel system, please refer to “Fuel System, Venting”.

NOTE! If a water trap is installed: change the filter in it at the same time as the fuel filter, and clean the water trap in the plastic bowl under the filter with a soft rag.

Primary fuel filter, change 1. Undo the cable from the water trap sensor.

2. Remove the water trap filter from the filter bracket.

Collect any spilled fuel in a collection vessel.

3. Remove the lower part of the water trap from the filter.

4. Clean the lower part of the water trap with a soft rag. Check that the drain hole in the lower part is not blocked.

5. Install a new seal on the lower part and lubricate the seal with diesel fuel. Re-install the lower part of the filter.

6. Lubricate the seal with diesel fuel. Screw the filter onto the filter bracket by hand until the rubber seal just touches the mating surface. Then tighten a further half turn, no more.

7. Connect the cable to the water trap sensor.

8. If necessary, vent the fuel system, please refer to “Fuel System, Venting”.

41

Maintenance

Draining condensate, fuel system NOTE! Put a collection vessel under the fuel filter to collect the condensate and fuel.

1. Open the drain nipple (1) in the base of the primary fuel filter.

2. Tighten the drain tap (1) when fuel without water starts to run out.

7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:33

1

Venting the fuel system The system does not need to be vented unless it has been run completely dry. Venting is then done with the hand pump on the fuel filter bracket.

42

Maintenance

Electrical system The engine is equipped with a 2-pole electrical system and an alternator. System voltage is 24V. WARNING! Before any work is done on the electrical system, the engine must be stopped and the current cut by switching off the main switch(es). All connections to equipment such as battery chargers or other auxiliary equipment must be broken.

Main switch

7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:33

The main switches must never be disconnected before the engine has been stopped. If the circuit between the alternator and the battery is disconnected when the engine is running, the alternator and electronics can be damaged. The charging circuits must never be re-connected with the engine running, for the same reason.

IMPORTANT! Never disconnect the current with the main switch(es) when the engine is running.

Circuit breaker The engine is equipped with a 10 A circuit breaker which cuts the current if overloaded.

The circuit breaker is located on the left-hand side of the engine, please refer to Component Location.

Note. The engine stops if the fuse trips.

If the circuit breaker trips frequently, an authorized Volvo Penta workshop should be contacted to investigate the cause of the overload.

Electrical connections Check that electrical connections are dry, free from oxide and that they are securely tightened. Spray these connections as necessary with water-repellent spray (Volvo Penta universal oil).

43

Maintenance

Battery. Maintenance WARNING! Fire and explosion hazard. Batteries must never be exposed to open flames or sparks.

WARNING! Never confuse the positive and negative poles on the batteries. Risk of arcing and explosion.

WARNING! Battery electrolyte is highly corrosive. Always protect your eyes, skin and clothes when handling batteries. Always use protective goggles and gloves. If acid comes into contact with your skin, wash at once with soap and a lot of water. If you get battery acid in your eyes, flush your eyes with a lot of water, and get medical assistance at once.

7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:33

Connection and disconnection When you connect batteries, first connect the + cable (red) to the + pole on the battery. Then connect the – cable (black) to the – pole on the battery When you disconnect batteries, connect the – cable (black) first, then the + cable (red).

Cleaning Keep the batteries dry and clean. Contamination and oxide on the batteries and battery poles can cause stray currents, voltage drop and discharge, especially in wet weather. Clean oxidation from the battery poles and terminals, using a brass brush. Tighten the terminals securely and grease them with terminal grease or Vaseline.

Filling The electrolyte level should be 5–10 mm above the cell plates in the battery. Fill up with distilled water if necessary: After filling, the battery should be charged for at least 30 minutes by running the engine at idle.

NOTE! Some maintenance-free batteries have special instructions, which must be observed.

44

Maintenance

Batteries, charging WARNING! Explosion risk! Hydrogen is given off when batteries are charged. This forms an explosive mixture with air. A short circuit, open flame or spark could cause a violent explosion. Ventilate well.

7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:33

WARNING! Battery electrolyte is highly corrosive. Protect your eyes, skin and clothes. Always use protective goggles and gloves. If acid comes into contact with your skin, wash at once with soap and a lot of water. If you get battery acid in your eyes, flush at once with a lot of cold water, and get medical assistance at once.

Charge batteries if they have become discharged. If the engine is not used for a longer period of time, the batteries should be fully charged, then possibly trickle charged (please refer to the battery manufacturer’s recommendations). Batteries are damaged by being left discharged, and can also freeze and burst easier in cold weather.

IMPORTANT! Observe the instruction manual for the battery charger carefully. To avoid the risk of electrochemical corrosion when an external charger is connected, the battery cables should be removed from the batteries before the charger is connected.

During charging, unscrew the cell plugs but leave them in the plug holes. Ventilate well, especially if the batteries are charged in an enclosed space.

WARNING! Always cut the charge current before the battery charger clamps are undone.

Never confuse the positive (+) and negative (-) poles on the batteries. This can cause serious arcing and can cause an explosion.

For so-called quick charging , there are special rules. Quick charging can shorten battery life, and should therefore be avoided.

45

Maintenance

7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:33

Component location

1. Coolant level sensor (in the expansion tank) 2. Extra stop 3. Charge pressure / charge temperature sensor 4. Air filter pressure and temperature sensor 5. Main circuit breaker 10 A 6. Connector interface (8-pin connector) 7. Main relay 8. Diagnostic connector (2-pin connector) 9. Oil pressure sensor 10. Fuel pressure sensor 11. Sensor, water in fuel 12. Oil level and oil temperature sensor (installed inside the oil pan) 13. Crankcase pressure sensor 14. Air pre-heater with pre-heating relay 15. Camshaft position sensor 16. Coolant temperature sensor 17. Piston cooling pressure sensor 18. Flywheel position and speed sensor

46

Laying up The engine and other equipment must be laid up to prevent damage if they are not used for two months or more. It is important that this is done in the correct manner, and nothing is forgotten. For this reason, we have compiled a check list of the most important points.

Before the engine is taken out of service for a long period of time, an authorized Volvo Penta workshop should check it over. Have any faults and deficiencies attended to, so that the equipment is in order, ready for the next start.

WARNING! Before you start to do any maintenance work, read the “Maintenance” chapter carefully. This contains instructions for doing work in a safe and correct manner.

WARNING! Some conservation oils are flammable. Some are also dangerous to breathe. Ensure good venti lation. Use a protective mask for spraying.

7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:33

IMPORTANT! Remember the following when washing with a high pressure washer: Never aim the water jet at seals, rubber hoses or electrical components.

Conservation up to 8 month’s stoppage: • For Change the oil and oil filter on the engine, then warm it up afterwards.

More than 8 month’s stoppage: Conserve the lubrication and fuel systems with conservation oil. Please refer to the instruction on the next page. that the coolant offers sufficient frost pro• Check tection. Top up as necessary. Alternatively, you can drain the coolant (also drain the coolant filter). any water and contamination from the fuel • Drain filters and fuel tank. Fill the fuel tank completely, to avoid condensation. the battery cables, clean and charge • Disconnect the batteries. Trickle charge the batteries while the equipment is laid up. A poorly charged battery can freeze and burst. the outside of the engine. Do not use a high • Clean pressure washer for engine cleaning. Touch up paint damage with Volvo Penta original paint. the components of the electrical system • Spray with water-repellent spray.

• Check and rust-proof any control cables. a note on the engine with the date, type of • Put conservation and the conservation oil used. over the air filter, exhaust pipe and engine • Cover ifnecessary.

47

Laying up

Removing conservation preparations any covers from the engine, air filter and • Remove exhaust pipe. the correct grade of oil into the engine, if nec• Put essary. Install a new oil filter if the filter was not changed during conservation.

7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:33

• Install new fuel filters and vent the fuel system.

• Check the drive belt(s). the condition of all rubber hoses, and re• Check tighten the hose clamps.

• Close the drain taps and install anydrainplugs.

• Check the coolant level. Top up as necessary.

• Connect the fully charged batteries. the engine and warm it up at fast idle with no • Start loading.

• Check that no oil, fuel or coolantleakageoccurs.

Conservation of the lubrication and fuel systems for more than 8 months’ stoppage: the engine oil and fill up with • Drain conservation oil* to just over the MIN marking on the dipstick. the fuel suction and return hoses to a • Connect 1/3 full jerrican containing conservation oil* and 2/3 diesel fuel.

• Vent the fuel system.

the engine and run at a fast idle until about • Start 2 liters (1 US quart) of the fluid in the jerrican have been used. Stop the engine and connect the ordinary fuel pipes.

• Drain the engine’s conservationoil. the other instructions on the previous • Follow page. * Conservation oils are sold by oil companies.

48

Diagnostic function The diagnostic function monitors and checks that the EMS 2 system functions normally.

The diagnostic function has the following tasks:

• Detecting and locating disturbances • Reporting detection of disturbances • Providing guidance when troubleshooting

Message regarding disturbance If the diagnostic function discovers a malfunction in the EMS 2 system, this is reported by means of fault codes/fault cause on the instruments.

7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:33

Both inactive (rectified) and active (un-mended) faults are stored in the control unit.

Please refer to the “Operation” heading for reading fault codes.

All fault codes are found in the fault code list, with information about the reason, reaction and measures to be taken. Please refer to the “Fault codes” chapter.

•

Fault codes can also be read by means of the VODIA tool. Please refer to the “VODIA User’s Guide” for advice on use.

At the same time, the fault is stored in the control unit memory. When the fault has been attended to and the ignition is switched off and on again, the fault disappears as active.

Inactive faults •

DCU - the fault is indicated as passive

•

CIU - the diagnostic lamp goes out

NOTE! All instruments are optional

•

DU - the fault message disappears (inactive faults can not be read)

Active faults

•

“Easy Link” - the warning lamp on the alarm panel turns off

DCU (Display Control Unit) / DU (Display Unit) • text” !! ENGINE WARNING !!” is shown on the display.

NOTE! It’s possible to choose which language the information will be presented in.

Effect on engine

CIU (Control Interface Unit) • the diagnostic lamp starts to flash.

Engines are affected differently, depending on the severity of the fault discovered by the diagnostic function.

•

A fault message in the form of a fault code is always generated when a malfunction is discovered by the diagnostic function.

“Easy-link” instrument (requires a CIU) - warning lamp on the alarm panel lights up - after the diagnostic button has been pressed, the fault code is shown as text on the tachometer display.

Engines are affected differently, depending on the severity of the fault.

DU (Display Unit) • Either “WARNING!” or “ALARM STOP” (a buzzer sounds) will be shown on the display, depending on the severity of the fault.

•

The engine is not affected

•

Engine idles

•

Engine torque is restricted to a certain amount

NOTE! You can choose the language used for the information presented on the.

•

Engine is stopped

49

Diagnostic function

Operation When a malfunction has occurred and the diagnostic system has generated one or more fault codes, these are read out differently, depending on the equipment used. Please refer to “Fault codes”.

If the system indicates that a fault code has been set: 1. Cut engine speed to idle, or shut the engine off.

2. For DCU/DU Read the fault code set from the display, please refer to “Reading fault cause via the DCU” or “Reading fault cause via DU”.

For CIU Press the diagnostic button and read the fault code that has been set, by observing the flashing of the diagnostic lamp. Please refer to “Reading fault codes via the diagnostic lamp, CIU”

7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:33

3. Look up the fault code/cause in the “Fault Code” chapter and take the recommended measures.

Reading fault cause via the DCU (Display Control Unit) When a fault code is set, the following text is shown on the display: “!! ENGINE WARNING !!” alternated with “Press SEL for information”.

NOTE! You can choose the language used for the information presented on the.

Read the fault code as follows: 1. Press the SEL button (to come to the error list.

The fault list shows: - Operation hours - Fault cause - Active/inactive 2. Look up the fault code in the “Fault Code” chapter and take the recommended measures.

3. Press the ESC button to leave the fault list.

NOTE! To enter the fault list when no fault code has been set, press the SEL button and select “Diagnostics” from the menu.

50

Reading fault cause via the DU (Display Unit) Depending on the severity of the faults, one of the following messages will appear on the display: “WARNING!” or “ALARM STOP” (a buzzer sounds).

1. Press any button to come to the fault list.

The fault list shows: - Operation hours - Fault cause 2. Look up the fault code in the “Fault Code” chapter and take the recommended measures.

3. Press ACK to confirm the fault code. The display background will change color (the buzzer stops sounding).

4. Press EXIT to leave the fault list.

Diagnostic function

Reading fault codes via the diagnostic lamp on the instrument panel, CIU

Reading fault codes via ”Easy Link” instrument (only with CIU)

When the system has discovered a malfunction, the diagnostic lamp starts to flash. If the diagnostic button is depressed and then released, a fault code is flashed out.

The fault code consists of two groups of flashes, separated by a pause of two seconds. A fault code is obtained by counting the number of flashes in each group.

When the system has discovered a malfunction, the diagnostic lamp starts to flash and the fault code will show in the display of the tachometer.

Example:

pause

= Fault code 2.4

The fault code is stored and can be read as long as the malfunction remains. You can find information about cause, reaction and actions in the “Fault Code” chapter.

1. Press the diagnostic button, the fault code will show in the display of the tachometer.

2. Look up the fault code in the “Fault Code” chapter and take the recommended measures.

3. When the fault has been attended to, the fault code disappears from the display and the diagnostic lamp goes out.

Read the fault code as follows: 1. Press the diagnostic button.

7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:33

2. Release the diagnostic button and make a note of the fault that is flashed out.

3. Repeat items 1-2. A new fault code is flashed out if more are stored. Repeat until the first fault code is repeated.

Erasing fault codes Fault codes must be erased by means of the VODIA tool.

4. Look up the fault code in the “Fault Code” chapter and take the recommended measures.

NOTE! When the first fault code is repeated, all fault codes have been read out.

If the diagnostic button is pressed after the fault has been mended and the fault codes have been erased, code 1.1 “No fault” will be displayed.

51

Fault codes WARNING! Read through the safety advice for care and maintenance work in the ”Safety information” chapter before you start work.

NOTE! Reading the fault codes below, such as Code 2.1, PID 97 means that 2.1 is the flashing code indicated by the diagnostic lamp. PID 97 is read with the VODIA diagnostic tool. With the use of DCU or DU the fault message will be shown as text in the display.

NOTE! Please refer to ”Wiring schedule CIU and DCU” for references to the sleeves in the electrical connectors on the engine control unit.

Code 1.1

There are no active faults.

7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:33

Code 2.4, SID21 / SPN 637 Flywheel speed sensor

No faults

Cause:

Code 2.1, PID / SPN 97. Water in fuel

•

No signal.

Cause:

•

Abnormal frequency.

•

•

“Intermittent” signal from the sensor.

Reaction:

•

Fault in sensor.

•

Reaction:

Water in fuel.

None.

Remedy: •

•

Empty the primary fuel filter.

Code 2.2, PID / SPN 111. Coolant level

Cause: •

Low coolant level.

Engine is very difficult to start and runs roughly when it starts.

Remedy: •

Check that the sensor connector is correctly installed.

•

Check that the engine speed sensor cable is not damaged.

Reaction: •

Warning indication.

•

•

Engine control module reduces engine power (unless the protection has been shut off with the VODIA diagnostic tool).

Check that the engine speed sensor is correctly installed in the flywheelhousing.

•

Check engine speed sensor function.

Remedy:

Code 2.5, SID22 / SPN 636 Camshaft drive speed sensor

•

Check the coolant level.

Cause:

•

Check coolant level monitor function.

•

No signal.

•

Abnormal frequency.

•

Fault in sensor.

Code 2.3, PID / SPN 111. Coolant level sensor Cause: •

Short circuit to positive (+).

•

Fault in sensor.

Reaction: •

None.

Remedy:

Reaction: •

Engine takes longer to start than normal. Engine runs normally when running.

Remedy: •

Check that the engine speed sensor connector is correctly installed.

•

Check that the coolant level sensor cable is not damaged.

•

Check that the engine speed sensor cable is not damaged.

•

Check coolant level sensor function.

•

Check that the engine speed sensor is correctly installed in the upper timing gear cover.

•

Check engine speed sensor function.

52

Fault codes Code 2.6, PID / SPN 190. Engine speed

Code 3.1, PID / SPN 100. Oil pressure sensor

Cause:

Cause:

•

•

Short circuit to positive (+) or earth (ground) (–).

Reaction:

•

Open circuit.

•

Reaction:

Engine speed too high.

None.

Remedy:

•

•

Remedy:

After the engine has stopped, look for the reason for the high speed.

Code 2.8, PPID 132 / SPN 608 Speed potentiometer connected to CIU

•

Check that the oil pressure sensor cable is not damaged.

•

Check that the oil pressure sensor is correctly connected.

Cause: •

Shorted to plus (+) or minus (-).

•

Fault in sensor.

Reaction:

7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:33

•

Engine goes to idle.

If you release the accelerator first, and the press it down again, the engine can be forced to run using the idle contact.

None.

Code 3.2, PID / SPN 105 Charge air temperature sensor Cause: •

Short circuit to positive (+) or earth (ground) (–).

•

Open circuit.

Reaction: •

None.

Remedy:

Remedy:

•

Check that the potentiometer has been connected correctly.

•

Check that the charge air temperature sensor connector is correctly installed.

•

Check that the cable harness to the potentiometer has not been damaged.

•

Check that the charge air temperature sensor cable is not damaged.

•

Check the potentiometer function.

•

Check that the charge air temperature sensor is correctly installed.

•

Check charge air temperature sensor function.

Code 2.9, PID / SPN 97 Indicator for water in fuel

Code 3.3, PID / SPN 110 Coolant temperature sensor

Cause: •

Short circuit

•

Open circuit.

•

Fault in indicator.

Reaction: •

None.

Remedy: •

Check the indicator cables for breaks and short circuits.

•

Check indicator function. Change indicator as necessary

Cause: •

Short circuit to positive (+) or earth (ground) (–).

•

Open circuit.

Reaction: •

Preheating is also activated when the engine is hot.

Remedy: •

Check that the coolant temperature sensor connector is correctly installed.

•

Check that the coolant temperature sensor cable is not damaged.

•

Check that the coolant temperature sensor is correctly installed.

•

Check coolant temperature sensor function.

53

Fault codes Code 4.6, PPID 3 / SID 39 / SPN 677 Start output / Start motor relay

Code 3.6, PID / SPN 94. Fuel pressure sensor Cause: •

Short circuit to positive (+) or earth (ground) (–).

Cause:

•

Open circuit.

•

Shorted to plus (+) or minus (-).

Reaction:

•

Activated for too long.

•

Reaction:

None.

Remedy:

•

The engine cannot be started.

•

Check that the fuel pressure sensor connector is correctly installed.

•

The engine starts immediately when ignition is turned on.

•

Check that the fuel pressure sensor cable is not damaged.

Remedy:

•

Check that the fuel pressure sensor is correctly installed.

•

Check fuel pressure sensor function.

•

Check that connections to the ignition key have not been damaged.

•

Check that the cable harness to the ignition key has not been damaged.

Code 4.8, PPID 6/ SPN 520195. Stop input EMS

7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:33

Code 3.7, PID / SPN 175. Oil temperature sensor Cause:

Cause:

•

Shorted to plus (+) or minus (-).

•

Short circuit to negative (-).

•

Break.

•

Open circuit.

Reaction:

Reaction:

•

•

None.

Remedy: •

Check that the cable harness to the oil temperature sensor has not been damaged.

•

Check that the oil temperature sensor has been connected correctly.

Engine can only be stopped with the auxiliary stop.

Remedy: •

Check that the starter switch connections are not damaged.

Code 5.2, PPID 4 / SPN 520194. Starter input CIU

Code 3.8, PID / SPN 94. Fuel pressure

Cause:

Cause:

•

Shorted to minus (-).

•

•

Activated for too long.

Low supply pressure.

Reaction:

Reaction:

•

None.

•

The engine cannot be started.

Remedy:

•

The engine starts immediately when ignition is turned on.

•

Check if it is possible to build up pressure with the hand pump.

Remedy:

•

Check the fuel filter.

•

•

Check the fuel pre-filter.

Check that connections to the ignition key have not been damaged.

•

Check that the cable harness to the ignition key has not been damaged.

Code 3.9, PID / SPN 158. Battery voltage, EMS Cause: •

Faulty alternator.

•

Faulty battery, battery cables.

Reaction: •

None.

Remedy: •

54

Check the supply voltage from the control unit.

Fault codes Code 5.3, PPID 6/ SPN 970. Stop input CIU

Code 5.7. PID / SPN 98, Oil level

Cause:

Cause:

•

Short circuit to negative (-).

•

•

Open circuit.

Reaction:

•

Activated for too long time.

•

Oil level is too low.

Warning indication.

Reaction:

Remedy:

•

Engine can only be stopped with the auxiliary stop (AUX STOP) on engine.

•

•

Engine stops. A fault code is displayed for 40 seconds and the engine can not be started during this time. When a fault code is active, the engine can be started but not stopped.

Remedy: •

Check that the starter switch connections are not damaged.

•

Check that the ignition switch cable is not damaged.

Check the oil level.

Code 5.8, PID / SPN 175. Oil temperature

Cause: •

Oil temperature is too high

Reaction: •

Warning indication.

•

The engine control module limits engine output (unless protection has been turned off with the diagnosis tool VODIA).

7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:33

Remedy: Code 5.4, PID 45/ SPN 626. Preheating relay Cause: •

Short circuit to positive (+) or earth (ground) (–).

•

Open circuit.

•

Check the oil level.

•

Check the oil temperature.

•

Check the oil temperature sensor function.

Code 5.9, PID / SPN 98. Oil level sensor

Reaction: •

Preheating can not be activated.

•

Preheating is constantly connected.

Remedy: •

Check that the relay input cable is not damaged.

•

Check relay function.

Code 5.6, PID/SPN 107. Air filter sensor

Cause: •

Shorted to plus (+) or minus (-).

•

Break.

Reaction: •

None

Remedy: •

Check that the air filter sensor contact is correctly installed.

•

Check that the cable harness to air filter sensor has not been damaged.

•

Check the air filter sensor functionality.

Cause: •

Shorted to plus (+) or minus (-).

•

Break.

Reaction: •

None.

Remedy: •

Check that the cable harness to the oil level sensor has not been damaged.

•

Check the oil level sensor function.

Code 6.1, PID / SPN 110. Coolant temperature

Cause: •

Coolant temperature is too high.

Reaction: •

Engine control module reduces engine power (unless the protection has been shut off with the VODIA diagnostic tool).

Remedy: •

Check the coolant level.

•

Check the intercooler (cleanliness).

•

Check if there is air in the cooling system.

•

Check the pressure cap on the expansion tank.

•

Check coolant temperature sensor function.

•

Check thermostat function.

55

Fault codes Code 6.2, PID / SPN 105. Charge air temperature

Code 6.6, PID / SPN 100, Oil pressure

Cause:

Cause:

•

•

Charge air temperature is too high.

Reaction:

Reaction:

•

•

Engine control module reduces engine power (unless the protection has been shut off with the VODIA diagnostic tool).

Engine control module reduces engine power (unless the protection has been shut off with the VODIA diagnostic tool).

Remedy:

Remedy:

•

Check the coolant level.

•

Check oil level.

•

Check the intercooler (cleanliness).

•

Check that the air filters are not blocked.

•

Check charge air temperature sensor function.

•

•

Check the function of the thermostat.

Check system pressure valves and safety valves in the oil system.

•

Check oil pressure sensor function.

Code 6.4, PPID 231 / SPN 639, Data link (CAN), CIU

Code 6.7, PPID 8 / SPN 520192, Piston cooling pressure

Cause: • 7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:33

Oil pressure is too low.

Faulty data link (CAN), CIU.

Reaction: •

Instruments and warning lamps stop working.

Remedy: •

Check that the 8-pin connector is not damaged.

•

Check that the cables between the CIU and the engine management unit are not damaged.

Cause: •

Reaction: •

•

Internal fault in control module.

Reaction: •

Engine not operating: engine can not be started.

Engine operating: engine idles and can only be stopped with the auxiliary stop (AUX-stop).

Engine stopped. The fault code is de-activated at engine speeds below 1000 rpm.

Remedy: •

Code 6.5, PPID 231 / SPN 639, Data link (CAN), EMS 2 Cause:

Piston cooling pressure is too low.

Check that the oil pressure in the engine exceeds 175 kPa (25.4 psi).

Code 6.8, PPID 8 / SPN 520192, Piston cooling pressure sensor

Cause: •

Shorted to plus (+) or minus (-).

•

Break.

Reaction: •

None.

Remedy:

Remedy:

•

Check that the 8-pin connector is not damaged.

•

•

Check that the cables between the CIU and the engine management unit are not damaged.

Check that the piston cooling pressure sensor contact is correctly installed.

•

Check that sleeves 11 and 12 in the connector on the CIU are not damaged.

Check that the cable harness to the piston cooling pressure sensor has not been damaged.

•

Check the piston cooling pressure sensor functionality.

•

56

Fault codes Code 7.2, SID 2 / SPN 652 Injector, cylinder #2

Code 6.9, PID / SPN 158, Battery voltage, CIU Cause: •

Short circuit to negative (-).

Cause:

•

Faulty alternator.

•

Electrical fault.

•

Faulty battery, battery cables.

•

Faulty compression or injector.

Reaction:

Reaction:

•

•

Engine runs on 5 cylinders.

Remedy:

•

Abnormal sound.

•

Check the supply voltage from the control unit.

•

Reduced performance.

•

Check the battery.

Remedy:

•

Check the alternator.

•

Check that the injector cables are not damaged.

•

Check the 8-pin contact.

•

Check that the injector connections are not damaged.

Code 7.1, SID 1 / SPN 651 Injector, cylinder #1

•

Check fuel supply pressure.

•

Check the valve clearance.

•

Do a compression test and check cylinder #2.

Problems in engine starting.

7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:33

Cause: •

Electrical fault.

•

Faulty compression or injector.

Code 7.3, SID 3 / SPN 653 Injector, cylinder #3

Reaction: •

Engine runs on 5 cylinders.

Cause:

•

Abnormal sound.

•

Electrical fault.

•

Reduced performance.

•

Faulty compression or injector.

Remedy:

Reaction:

•

Check that the injector cables are not damaged.

•

Engine runs on 5 cylinders.

•

Check that the injector connections are not damaged.

•

Abnormal sound.

•

Reduced performance.

•

Check fuel supply pressure.

Remedy:

•

Check the valve clearance.

•

Do a compression test and check cylinder #1.

•

Check that the injector cables are not damaged.

•

Check that the injector connections are not damaged.

•

Check fuel supply pressure.

•

Check the valve clearance.

•

Do a compression test and check cylinder #3.

57

Fault codes Code 7.4, SID 4 / SPN 654 Injector, cylinder #4 Cause: •

Electrical fault.

•

Faulty compression or injector.

Reaction: •

Engine runs on 5 cylinders.

•

Abnormal sound.

•

Reduced performance.

7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:33

Remedy: •

Check that the injector cables are not damaged.

•

Check that the injector connections are not damaged.

•

Check fuel supply pressure.

•

Check the valve clearance.

•

Do a compression test and check cylinder #4.

Code 7.6, SID 6 / SPN 656 Injector, cylinder #6 Cause: •

Electrical fault.

•

Faulty compression or injector.

Reaction: •

Engine runs on 5 cylinders.

•

Abnormal sound.

•

Reduced performance.

Remedy: •

Check that the injector cables are not damaged.

•

Check that the injector connections are not damaged.

•

Check fuel supply pressure.

•

Check the valve clearance.

•

Do a compression test and check cylinder #6.

Code 7.7, PID / SPN 153 Crankcase ventilation pressure

Code 7.5, SID 5 / SPN 655 Injector, cylinder #5 Cause: •

Electrical fault.

•

Faulty compression or injector.

Reaction: •

Engine runs on 5 cylinders.

•

Abnormal sound.

•

Reduced performance.

Remedy:

Cause: •

Crankcase ventilation pressure too high.

Reaction: •

The engine is shut down (if the protection has not been shut off by the parameter tool).

Remedy: •

Check whether the crankcase ventilation is blocked.

•

Check whether cylinder liner, piston or piston rings are worn or damaged.

•

Check that the injector cables are not damaged.

•

Check that the injector connections are not damaged.

Code 7.8, PID / SPN 153 Crankcase ventilation pressure sensor

•

Check fuel supply pressure.

Cause:

•

Check the valve clearance.

•

Shorted to plus (+) or minus (-).

•

Do a compression test and check cylinder #5.

•

Break.

Reaction: •

None.

Remedy:

58

•

Check that the crankcase ventilation pressure sensor contact is correctly installed.

•

Check that the cable harness to the crankcase ventilation pressure sensor has not been damaged.

•

Check crankcase ventilation pressure sensor function.

Fault codes Code 7.9, PID / SPN 172 Air temperature sensor, inlet

Code 9.8, SID 253 / SPN 630 Data set memory EEPROM, CIU

Cause:

Cause:

•

Shorted to plus (+) or minus (-).

•

Internal fault in control module

•

Break.

•

Programming faulty.

Reaction:

Reaction:

•

•

None.

Remedy: •

Check that the air temperature sensor contact is correctly installed.

•

Check that the cable harness to the air temperature sensor has not been damaged.

• •

Check the air temperature sensor functionality.

Check the preheating relay.

Remedy: •

Re-program the control module. If the fault remains, change the control module.

Code 9.8, PPID 254 / SPN 629 Fault in control unit, CIU

Cause: •

Faulty EEPROM, CIU.

•

Faulty flash memory, CIU.

Cause:

•

Fault in control module, CIU

•

Reaction:

Code 9.2, SID250 / SPN 608 Faulty data link (J1587) 7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:33

Engine does not start.

Faulty data link.

Reaction:

•

CIU returns to factory setting.

•

None.

•

Engine goes to idle.

Remedy:

•

Engine can not be started.

•

Check that the 8-pin connector is not damaged.

Remedy:

•

Check that the cables between the CIU/DCU and the engine management unit are not damaged.

•

Re- program the unit

•

Change CIU unit.

Code 9.3, SID 232 / SPN 620 Power supply to sensor Cause: •

Shortcut.

•

Fault in sensor.

Reaction: •

Faulty values in oil pressure and charge air pressure sensors.

•

Fault code for oil pressure- and charge air pressure sensor.

•

Low engine output.

•

The instrument shows zero oil pressure and boost pressure.

Code 9.9, SID 240 / SPN 639. Memory fault Cause: •

Memory fault in engine management system.

Reaction: •

Engine might not start.

Remedy: •

Re-program the unit.

Remedy: •

Check that the cable harness to oil pressure and charge air pressure sensor has not been damaged.

•

Check oil pressure and charge air pressure sensors.

59

Fault codes Code 9.9, SID 253 / SPN 630 Data set memory EEPROM, EMS Cause: •

Internal fault in control module

•

Programming faulty.

Reaction: •

Engine does not start.

Remedy: •

Re-program the control module. If the fault remains, change the control module.

Code 9.9, SID 254 / SPN 629 Control module EMS

Cause: •

Internal fault in control module.

7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:33

Reaction: •

Engine misfires.

•

Engine does not start.

Remedy: •

60

Change engine control unit.

Technical data General

7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:33

Designation

TAD1640GE

TAD1641GE

Power, Prime/Stand-by

See sales literature

Torque, Prime/Stand-by

See sales literature

TAD1642GE

TAD1641VE

TAD1642VE

No. of cylinders

6

6

6

6

6

Bore

144

144

144

144

144

Stroke, mm

165

165

165

165

165

Cylinder volume, dm3

16,12

16,12

16,12

16,12

16,12

Weight, dry (kg)

1440

1440

1480

1480

1480

Weight, wet (kg)

1510

1510

1550

1550

1550

Injection sequence

1-5-3-6-2-4

1-5-3-6-2-4

1-5-3-6-2-4

1-5-3-6-2-4

1-5-3-6-2-4

Compressionratio

17.5:1

16.5:1

16.5:1

17.5:1

17.5:1

Low idle, rpm

900

900

900

600

600

High idle, rpm

1500/1800

1500/1800

1500/1800

1800-2000

1800-2000

61

Technical data

Lubrication system Oil Change volume, including filter change ................. 48 liter (12.6 US gallon) Oil pressure, hot engine at operating speed ................................................ 300-650 kPa (44-94 psi) at idle, min ............................................................ 270 kPa (39 psi) Oil grade ............................................................... Please refer to the specification under “Maintenance”.

Viscosity ............................................................... Please refer to the specification under “Maintenance”.

Oil filter Full flow filter ......................................................... 2 By-passfilter .......................................................... 1

7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:33

Oil pump Type ..................................................................... Gear driven

62

Technical data

Fuel system Feed pump Matartryck vid 600 r/min ............................................

Supply pressure at 1200 rpm .....................................

Supply pressure at full load ........................................

By - pass valve Opening pressure .......................................................

min 100 kPa (14.5 psi) min 300 kPa (43.5 psi) min 300 kPa (43.5 psi) 400-550 kPa (58-80 psi)

Fuel specification

7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:33

The fuel must comply with national and international standards for commercially supplied fuels, such as: EN 590 (with nationally adapted environmental and cold requirements) ASTM D 975 No 1 - D and 2 - D. JIS KK 2204 Sulfur content: Complying with legal requirements in each country.

Low density fuel (urban diesel in Sweden and city diesel in Finland) can cause a loss of up to 5% of power and an increase in fuel consumption of about 2-3%.

63

Technical data

Cooling system Type ..........................................................................

Pressure cap, max. opening pressure ........................

Volume (engine) .........................................................

Pressurized, sealed 75 kPa (11 psi) 20 liter (21.1 US quart)

Volume (engine + radiator and hoses) ........................

60 liter (15.8 US gallon)

Thermostat

7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:33

Quantity .....................................................................

Opening temperature ..................................................

1 pcs.

86° C (187° F)

Electrical system System voltage ..........................................................

Alternator voltage/max. current density ................................... power app. ..............................................................

Alternative generating equipment (optional): ............... voltage/max. current density ................................... power app. ..............................................................

Battery capacity .........................................................

Battery electrolyte specific gravity at +25°C: fully charged battery ............................................... re-charge battery at ................................................. * NOTE! Applies to batteries with tropical acid.

64

24V

28V / 80A 2200W 28V/110A 2800W 2 pcs. series connected 12V, max. 225 Ah 1,28 g/cm3 (1,24 g/cm3)* 1,20 g/cm3 (1,20 g/cm3)*

Notes ........................................................................................................................................................................................... ........................................................................................................................................................................................... ........................................................................................................................................................................................... ........................................................................................................................................................................................... ........................................................................................................................................................................................... ........................................................................................................................................................................................... ........................................................................................................................................................................................... ...........................................................................................................................................................................................

7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:33

........................................................................................................................................................................................... ........................................................................................................................................................................................... ........................................................................................................................................................................................... ........................................................................................................................................................................................... ........................................................................................................................................................................................... ........................................................................................................................................................................................... ........................................................................................................................................................................................... ........................................................................................................................................................................................... ........................................................................................................................................................................................... ........................................................................................................................................................................................... ........................................................................................................................................................................................... ........................................................................................................................................................................................... ........................................................................................................................................................................................... ........................................................................................................................................................................................... ........................................................................................................................................................................................... ........................................................................................................................................................................................... ........................................................................................................................................................................................... ...........................................................................................................................................................................................

Notes ........................................................................................................................................................................................... ........................................................................................................................................................................................... ........................................................................................................................................................................................... ........................................................................................................................................................................................... ........................................................................................................................................................................................... ........................................................................................................................................................................................... ........................................................................................................................................................................................... ...........................................................................................................................................................................................

7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:33

........................................................................................................................................................................................... ........................................................................................................................................................................................... ........................................................................................................................................................................................... ........................................................................................................................................................................................... ........................................................................................................................................................................................... ........................................................................................................................................................................................... ........................................................................................................................................................................................... ........................................................................................................................................................................................... ........................................................................................................................................................................................... ........................................................................................................................................................................................... ........................................................................................................................................................................................... ........................................................................................................................................................................................... ........................................................................................................................................................................................... ........................................................................................................................................................................................... ........................................................................................................................................................................................... ........................................................................................................................................................................................... ........................................................................................................................................................................................... ...........................................................................................................................................................................................

✂ Yes please, I would like an operator’s manual in English at no charge.

Orders can also be placed via the Internet: http://www.volvopenta.com/ manual/coupon

Publication number: 7745140 42200/615001/155099900192

Post or fax this coupon to: Document & Distribution Center Order Department ARU2, Dept. 64620 SE-405 08 Göteborg Sweden Fax: +46 31 545 772

Name

Address

Country

✂ Ja danke, ich will kostenlos eine Betriebsanleitung in deutscher Sprache erhalten.

Die Bestellung kann auch über das Internet erfolgen: http://www.volvopenta.com/ manual/coupon

Publikationsnummer: 7746103 42200/615001/155099900192

Schicken Sie den Coupon per Post oder als Fax an: Document & Distribution Center Order Department ARU2, Dept. 64620 SE-405 08 Göteborg Schweden Fax: +46 31 545 772

Name

Anschrift

Land

Bitte beachten Sie, dass das Angebot für die Dauer von 12 Monaten ab dem Lieferdatum des Motors gilt, danach nur noch bis zum Aufbrauchen des Lagerbestandes.

✂ Oui merci, Envoyez ou faxez le bon de commande à: Document & Distribution Center Order Department ARU2, Dept. 64620 SE-405 08 Göteborg Suède Fax: +46 31 545 772 Vous pouvez également passer la commande par Internet: http://www.volvopenta.com/ manual/coupon

Je souhaite recevoir un manuel d’instructions gratuit en français.

Numéro de publication: 7746104 Nom

Adresse

Pays

Noter que l’offre est valable 12 mois à partir de la date de livraison du moteur, puis seulement dans la mesure des stocks disponibles.

42200/615001/155099900192

7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:33

Please note that this offer is valid for 12 months from the date of delivery of the engine, after this it is subject to availability.

✂ Sí gracias, deseo recibir gratuitamente un libro de instrucciones en español.

Número de publicación: 7746105 42200/615001/155099900192

Franquear o enviar fax a: Document & Distribution Center Order Department ARU2, Dept. 64620 SE-405 08 Göteborg Suecia Fax: +46 31 545 772

Nombre

Direc

El pedido puede hacerse también por internet: http://www.volvopenta.com/ manual/coupon País

✂ Sì, grazie,

L’ordinazione può essere fatta anche su Internet: http://www.volvopenta.com/ manual/coupon

desidero ricevere gratuitamente un manuale d’istruzioni in lingua italiana.

Public. No.: 7746106 42200/615001/155099900192

Spedire il tagliando per posta o per fax a: Document & Distribution Center Order Department ARU2, Dept. 64620 SE-405 08 Göteborg Svezia Fax: +46 31 545 772

Nome e Cognome

Indirizzo

Paese

Notare che la validità dell’offerta è garantita solo per 12 mesi dalla consegna del motore, dopodiché si procederà fino ad esaurimento scorte.

✂ Ja tack, Posta eller faxa kupongen till: Dokument & Distribution center Ordermottagningen ARU2, Avd. 64620 SE-405 08 Göteborg Sverige Fax: +46 31 545 772

jag vill kostnadsfritt ha en instruktionsbok på svenska.

Publikationsnummer: 7746101 Namn

Adress

Beställningen kan även göras via internet: http://www.volvopenta.com/ manual/coupon Land

Observera att erbjudandet gäller i 12 månader från motorns leveransdatum, därefter endast i mån av tillgång.

42200/615001/155099900192

7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:33

Observe que la oferta es válida durante 12 meses a partir de la fecha de entrega del motor. A partir de la fecha de finalización de la oferta, la misma es válida siempre que haya existencias.

✂ Ja graag, Ik wil kosteloos een instructieboek in het Nederlands ontvangen.

Publicatienummer: 7746108 42200/615001/155099900192

Stuur of fax de coupon naar: Document & Distribution Center Order Department ARU2, Dept. 64620 SE-405 08 Göteborg Zweden Fax: +46 31 545 772

Naam

Adres

U kunt ook bestellen via internet: http://www.volvopenta.com/ manual/coupon Land

✂ Kyllä kiitos,

Tilauksen voi tehdä myös Internetissä: http://www.volvopenta.com/ manual/coupon

haluan suomenkielisen ohjekirjan veloituksetta.

Julkaisunumero: 7746107 42200/615001/155099900192

Postita tai faksaa kuponki osoitteella: Document & Distribution Center Order Department ARU2, Dept. 64620 SE-405 08 Göteborg Ruotsi Fax: +46 31 545 772

Nimi

Osoite

Maa

Ota huomioon, että tarjous on voimassa 1 vuoden ajan moottorin luovutuspäivämäärästä, sen jälkeen vain tuotteen saatavuuden perusteella.

✂ Sim, obrigado(a)!

Envie o talão pelo correio ou um fax para: Document & Distribution Center Order Department ARU2, Dept. 64620 SE-405 08 Göteborg Suécia Fax: +46 31 545 772 A encomenda também pode ser feita através da Internet: http://www.volvopenta.com/ manual/coupon

Gostaria de receber gratuitamente um manual de instruções em português.

Número de publicação: 7746109 Nome

Endereço

País

Notar que a oferta é válida por um período de 12 meses a partir da data de entrega do motor. Depois desse período, a oferta é válida consoante a disponibilidade.

42200/615001/155099900192

7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:33

Denk eraan dat de aanbieding geldt tot 12 maanden na levering van de motor, daarna nog slechts indien beschikbaar.

Íáé,

7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:33

Áñéèìüò Ýêäïóçò: 7746110 ¼íïìá Äéåýèõíóç

×þñá

Ðáñáêáëïýìå óçìåéþóôå üôé áõôÞ ç ðñïóöïñÜ éó÷ýåé ãéá 12 ìÞíåò áðü ôçí çìåñïìçíßá ðáñÜäïóçò ôçò ìç÷áíÞò. ÌåôÜ èá åßíáé èÝìá äéáèåóéìüôçôáò.

Äà, ïîæàëóéñòà, Îòïðàâüòå ýòîò òàëîí ïî÷òîé èëè ôàêñîì íà èìÿ: Document & Distribution Center Order Department ARU2, Dept. 64620 SE-405 08 Göteborg Sweden

ðàçìåùàòü ÷åðåç Èíòåðíåò: http://www.volvopenta.com/ manual/coupon

✂

ß áû õîòåë èìåòü áåñïëàòíîå ðóêîâîäñòâî îïåðàòîðà íà ðóññêîì ÿçûêå. Íîìåð èçäàíèÿ: 7746112 Èìÿ Àäðåñ

Fax: +46 31 545 772 Çàêàçû òàêæå ìîæíî

42200/615001/155099900192

Ìðïñåßôå åðßóçò íá äþóåôå ôçí ðáñáããåëßá óáò ìÝóù ôïõ Internet, óôç äéåýèõíóç: http://www.volvopenta.com/ manual/coupon

Èá Þèåëá Ýíá áíôßôõðï ôïõ åã÷åéñéäßïõ ÷ñÞóçò óôçí áããëéêÞ ãëþóóá ÷ùñßò êáìéÜ ÷ñÝùóç.

Ñòðàíà Ê Âàøåìó ñâåäåíèþ, ýòî ïðåäëîæåíèå äåéñòâèòåëüíî â òå÷åíèå 12 ìåñÿöåâ îò äàòû ïîñòàâêè äâèãàòåëÿ; â äàëüíåéøåì îíî çàâèñèò îò íàëè÷èÿ.

42200/615001/155099900192

Ôá÷õäñïìÞóôå áõôü ôï êïõðüíé óôçí ðáñáêÜôù äéåýèõíóç Þ óôåßëôå ôï ìå öáî óôïí ðáñáêÜôù áñéèìü öáî: Document & Distribution Center Order Department ARU2, Dept. 64620 SE-405 08 Göteborg Sweden Fax: +46 31 545 772

✂

✂ Ja graag, Ik wil kosteloos een instructieboek in het Nederlands ontvangen.

Publicatienummer: 7746108 42200/615001/155099900192

Stuur of fax de coupon naar: Document & Distribution Center Order Department ARU2, Dept. 64620 SE-405 08 Göteborg Zweden Fax: +46 31 545 772

Naam

Adres

U kunt ook bestellen via internet: http://www.volvopenta.com/ manual/coupon Land

✂ Kyllä kiitos,

Tilauksen voi tehdä myös Internetissä: http://www.volvopenta.com/ manual/coupon

haluan suomenkielisen ohjekirjan veloituksetta.

Julkaisunumero: 7746107 42200/615001/155099900192

Postita tai faksaa kuponki osoitteella: Document & Distribution Center Order Department ARU2, Dept. 64620 SE-405 08 Göteborg Ruotsi Fax: +46 31 545 772

Nimi

Osoite

Maa

Ota huomioon, että tarjous on voimassa 1 vuoden ajan moottorin luovutuspäivämäärästä, sen jälkeen vain tuotteen saatavuuden perusteella.

✂ Sim, obrigado(a)!

Envie o talão pelo correio ou um fax para: Document & Distribution Center Order Department ARU2, Dept. 64620 SE-405 08 Göteborg Suécia Fax: +46 31 545 772 A encomenda também pode ser feita através da Internet: http://www.volvopenta.com/ manual/coupon

Gostaria de receber gratuitamente um manual de instruções em português.

Número de publicação: 7746109 Nome

Endereço

País

Notar que a oferta é válida por um período de 12 meses a partir da data de entrega do motor. Depois desse período, a oferta é válida consoante a disponibilidade.

42200/615001/155099900192

7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:33

Denk eraan dat de aanbieding geldt tot 12 maanden na levering van de motor, daarna nog slechts indien beschikbaar.

Íáé,

7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:33

Áñéèìüò Ýêäïóçò: 7746110 ¼íïìá Äéåýèõíóç

×þñá

Ðáñáêáëïýìå óçìåéþóôå üôé áõôÞ ç ðñïóöïñÜ éó÷ýåé ãéá 12 ìÞíåò áðü ôçí çìåñïìçíßá ðáñÜäïóçò ôçò ìç÷áíÞò. ÌåôÜ èá åßíáé èÝìá äéáèåóéìüôçôáò.

Äà, ïîæàëóéñòà, Îòïðàâüòå ýòîò òàëîí ïî÷òîé èëè ôàêñîì íà èìÿ: Document & Distribution Center Order Department ARU2, Dept. 64620 SE-405 08 Göteborg Sweden

ðàçìåùàòü ÷åðåç Èíòåðíåò: http://www.volvopenta.com/ manual/coupon

✂

ß áû õîòåë èìåòü áåñïëàòíîå ðóêîâîäñòâî îïåðàòîðà íà ðóññêîì ÿçûêå. Íîìåð èçäàíèÿ: 7746112 Èìÿ Àäðåñ

Fax: +46 31 545 772 Çàêàçû òàêæå ìîæíî

42200/615001/155099900192

Ìðïñåßôå åðßóçò íá äþóåôå ôçí ðáñáããåëßá óáò ìÝóù ôïõ Internet, óôç äéåýèõíóç: http://www.volvopenta.com/ manual/coupon

Èá Þèåëá Ýíá áíôßôõðï ôïõ åã÷åéñéäßïõ ÷ñÞóçò óôçí áããëéêÞ ãëþóóá ÷ùñßò êáìéÜ ÷ñÝùóç.

Ñòðàíà Ê Âàøåìó ñâåäåíèþ, ýòî ïðåäëîæåíèå äåéñòâèòåëüíî â òå÷åíèå 12 ìåñÿöåâ îò äàòû ïîñòàâêè äâèãàòåëÿ; â äàëüíåéøåì îíî çàâèñèò îò íàëè÷èÿ.

42200/615001/155099900192

Ôá÷õäñïìÞóôå áõôü ôï êïõðüíé óôçí ðáñáêÜôù äéåýèõíóç Þ óôåßëôå ôï ìå öáî óôïí ðáñáêÜôù áñéèìü öáî: Document & Distribution Center Order Department ARU2, Dept. 64620 SE-405 08 Göteborg Sweden Fax: +46 31 545 772

✂

7745140 - Downloaded from www.volvopenta.com 11/05/2006 10:22:33

7745140 English 12-2005

AB Volvo Penta SE-405 08 Göteborg, Sweden www.volvopenta.com