Tigercat T234B TRACK LOADER OPERATOR’S MANUAL SN 234T7001-234T8000 - PDF DOWNLOAD

T234B TRACK LOADER

OPERATOR’S MANUAL SERIAL NUMBER 234T7001 TO 234T8000

ISSUE 1.5, DECEMBER 2015 Tigercat Industries Inc. P.O. Box 637 Brantford, Ontario Canada N3T 5P9 Tel: (519) 753-2000 Fax: (519) 753-8272

Introduction

Tigercat T234B Track Loader

ii

Tigercat T234B Track Loader

Introduction

Tigercat T234B TRACK LOADER TABLE OF CONTENTS INTRODUCTION.................................................................................................................................................... v NON-APPROVED FIELD PRODUCT CHANGES.................................................................................................vi REGULATORY INFORMATION............................................................................................................................vii SAFETY................................................................................................................................................................. 1 CONTROLS AND OPERATION............................................................................................................................. 2 LUBRICATION AND MAINTENANCE.................................................................................................................... 3

CALIFORNIA Proposition 65 Warning Diesel engine exhaust and some of its constituents are known to the State of California to cause cancer, birth defects and other reproductive harm.

T234B Track Loader Available Literature Operator's Manual (This Manual).....................................................................................................Part No. 46749AENG Service Manual.................................................................................................................................Part No. 46750AENG Parts Catalog....................................................................................................................................Part No. 46751A Vehicle Moving and Transporting Instructions..................................................................................Part No. 47882AMUL Engine Operation and Maintenance Manual, N45/N67 T4f..............................................................Part No. 42939AMUL iii

Introduction

Tigercat T234B Track Loader

iv

Tigercat T234B Track Loader Tigercat T234B Track

INTRODUCTION

Loader

Introduction

An Operator's manual, Service manual and a Parts catalog are made available by Tigercat to assist the dealer, customer and operator in becoming familiar with the features of the T234B Track Loaders Serial numbers: 234T7001 to 234T8000.

The T234B Track Loader is designed for log processing, sorting, log transferring and loading.

The operator's manual will assist the operator with the techniques of proper and safe operation of the T234B Track Loader. There is also important information regarding the safe operation of the attachment. The service manual contains safety and servicing procedures and a preventive maintenance schedule to ensure optimum machine performance. ,,,,

Section 1 in both the operator's manual and the service manual contains safety information that must be followed. As well, throughout the rest of the manuals, WARNING and CAUTION notices are displayed where necessary, drawing attention to possible hazards when performing certain procedures.

Only trained personnel should be allowed to operate or work on the machine.

The information contained in this manual is current at time of printing. Improvements to the machine are on-going and may not be covered, therefore in these cases contact your Tigercat dealer for the appropriate information.

The phrase “and up” appearing in this manual after the serial number implies that the related information is current for any machine serial number HIGHER than the serial number preceding the “and up”.

Tigercat reserves the right to make changes to the machine after this manual release date that may not immediately appear in this manual.

Every effort is made to send out updates on a regular basis. If the machine in question was built after the release date of this manual and there is a discrepancy, call Tigercat service department. The release date appears on the first page.

The Company reserves the right to change information contained herein at any time without prior notice.

Tigercat Industries Inc.

v

Introduction

Tigercat T234B Track Loader

NON-APPROVED FIELD PRODUCT CHANGES

The installation of any unauthorized attachment or changes made of any kind to this Tigercat product could affect the product's ability to perform as originally intended. The product's integrity, stability and it's ability to perform safely could be at serious risk.

IT IS Tigercat POLICY THAT NO CHANGES ARE TO BE MADE TO ITS PRODUCTS INCLUDING DELETIONS OR ADDITIONS OTHER THAN A Tigercat APPROVED OPTION FITTED IN THE FACTORY APPROVED MANNER. Official approval to make changes or install options is only to be undertaken as follows: i) The relevant options for that product must be shown or listed on current Tigercat documentation or literature such as a printed specification sheet, price list, parts manual, or product literature issued by Tigercat. ii) Approved options or product changes authorized in writing by the Tigercat Engineering Manager.

AUTHORIZATION BY ANY OTHER PERSON IS UNACCEPTABLE. Unauthorized changes made or contributed to by a person or organization may result in creating a dangerous situation and therefore the person or organization will be considered to have assumed the risk involved or be negligent in having created this situation.

Weight is an important factor when considering the addition of options or an attachment, Refer to your Tigercat distributor for information on maximum permissible operating weight and the effect the addition of various options may have on your machine.

Tigercat will not be held responsible for any situation that may arise resulting from Non-approved Field Product Changes to its product.

Should Tigercat become involved in a dispute resulting from changes made to the product without proper authorization by Tigercat as stated above, Tigercat will take whatever action is appropriate to protect its interests.

The product warranty policy and the certification on any safety items installed on the modified product will become NULL and VOID if the above policy is not adhered to as specified.

Non-approved product changes also nullify warranties given to Tigercat by its component manufacturers.

Tigercat Industries Inc.

vi

Tigercat T234B Track Loader

Introduction

REGULATORY INFORMATION The operator's cab is equipped with standard or optional equipment that is capable of emitting radio frequency fields.

Bluetooth and Wi-Fi exposure limits are significantly less than the maximum permitted for public use.

IMPORTANT! The RemoteLog™ satellite antenna is externally mounted to the operator cab. When transmitting, the external antenna should always be separated from personnel by a minimum distance of 20 cm (8 in). Transmissions can be silenced by placing the telematics system in repair mode.

FEDERAL COMMUNICATIONS COMMISSION NOTIFICATIONS TO USER INTERNAL (OPERATOR'S CAB): Telematics Module (Wi-Fi)

Contains FCC ID: NCMOCG2101

IQAN-G11 (Bluetooth)

Contains FCC ID: VPYLBZY

Radio (Bluetooth)

Contains FCC ID: OPDJHD36A

Radio (Bluetooth)

Contains FCC ID: OPDJHD1635BT

Radio (Bluetooth)

Contains FCC ID: OPDJHD3630BT

EXTERNAL: Inmarsat Modem (Satellite)

Contains FCC ID: B92IDP1XX

Iridium Modem (Satellite)

Contains FCC ID: Q639603N

These devices comply with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines. This equipment has very low levels of RF energy that is deemed to comply without maximum permissive exposure evaluation (MPE).

INDUSTRY CANADA NOTIFICATIONS TO USER INTERNAL (OPERATOR'S CAB): Telematics Module (Wi-Fi)

Contains IC ID: NCMOCG2101

IQAN-G11 (Bluetooth)

Contains IC ID: VPYLBZY

EXTERNAL: Inmarsat Modem (Satellite)

Contains IC ID: B92IDP1XX

Iridium Modem (Satellite)

Contains IC ID: Q639603N

These devices comply with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment and meets RSS102 of the IC radio frequency (RF) Exposure rules. This equipment has very low levels of RF energy that is deemed to comply without maximum permissive exposure evaluation (MPE).

vii

Introduction

Tigercat T234B Track Loader

viii

Tigercat T234B Loader SECTION 1 – SAFETY Read and understand this Safety section prior to operating any equipment.

Read and understand all manuals for any attachments or accessories.

CONTENTS - SECTION 1

ISSUE 1.2, APRIL 2016

B

BATTERY DISCONNECT SWITCH........................................................................................................1.10 BATTERY SAFETY...................................................................................................................................1.6 C

CAB EXITS................................................................................................................................................1.8 COOLING SYSTEM................................................................................................................................1.15 D

DEF (DIESEL EXHAUST FLUID)..............................................................................................................1.7 E

EMERGENCY CAB EXITS........................................................................................................................1.8 ENGINE DOORS.....................................................................................................................................1.15 EXHAUST FUMES..................................................................................................................................1.15 F

FIRE PREVENTION................................................................................................................................1.22 DRY CHEMICAL CLEANUP PROCEDURES.......................................................................................1.26 FIRE PREVENTION GUIDELINES.......................................................................................................1.22 WHAT TO DO AFTER A MACHINE FIRE HAS OCCURRED...............................................................1.25 WHAT TO DO TO PREPARE FOR A MACHINE FIRE.........................................................................1.23 WHAT TO DO WHEN A MACHINE FIRE OCCURS.............................................................................1.24 FLUID INJECTION INJURY....................................................................................................................1.17 FLUID LEAKS.........................................................................................................................................1.12 G

GREASE INJECTION INJURY................................................................................................................1.18 H

HYDRAULIC PRESSURE HAZARD.......................................................................................................1.12 L

LIGHTNING SAFETY AWARENESS LIGHTNING SAFETY...........................................................................................................................1.19 WHAT IS A LIGHTNING STRIKE?........................................................................................................1.19 LOOSE CLOTHING HAZARD.................................................................................................................1.15 P

PROTECTIVE CLOTHING........................................................................................................................1.2 S

SAFETY LABELS....................................................................................................................................1.27 SAFETY PRECAUTIONS, GENERAL......................................................................................................1.2 SAFETY PRECAUTIONS, OPERATING...................................................................................................1.7 SAFETY PRECAUTIONS, SERVICING........................................................................................ 1.12, 1.19 SAFETY SYMBOLS..................................................................................................................................1.2 SIGNAL WORDS.......................................................................................................................................1.2 W

WELDING, PRIOR TO............................................................................................................................1.13 WORKING WITH OIL................................................................................................................................1.4

Safety

Tigercat T234B Loader

GENERAL SAFETY PRECAUTIONS

SAFETY SYMBOLS

Remember that safety is a prime responsibility of all.

To minimize the risks and promote safety at all times, this section of the operator’s manual details a number of safety rules which should always be followed and obeyed.

This safety alert symbol means ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

Always read the operator's manual before operating the machine. Pay close attention to WARNINGS and HAZARD identifications.

The safety alert symbol identifies important safety messages on machines, safety signs, in manuals, or elsewhere. When you see this symbol, be alert to the possibility of personal injury or death.

Follow the instructions in the safety message.

Understanding Signal Words

DANGER

Follow all instructions from safety inspector and supervisors.

DANGER – Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

You must be fully trained to operate this piece of equipment. Know the capabilities and the limitations of the equipment. Learn the most efficient operating techniques.

WARNING

Do not let untrained persons operate the machine.

WARNING – Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION CAUTION – Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.

Use recommended protective clothing and safety devices such as gloves, safety boots, safety hat, goggles, and ear protection when necessary.

These safety rules highlight both general and specific measures that the operator should be familiar with and adhere to. More specific measures are illustrated with pictograms which may also be attached to the machine in locations pertinent to their respective message. Keep safety labels in good condition. Repair or replace damaged labels.

1.2

Tigercat T234B Loader

Safety Do not try to climb onto or off of a moving machine.

KEEP CLEAR

Do not use the seat armrest or joystick as handle when entering or leaving the cab.

Do not use the machine foot controls as steps.

43424BUNI R0

All personnel should be made AWARE of the HAZARD ZONE and be kept clear of this zone and it should be considered off limits to all individuals while the machine is operating.

The HAZARD ZONE is the area around the machine when the machine is being operated.

When approaching an operating machine on foot, stay at least 150 m (500 ft) away from the machine and all related attachments including the grapple, delimber, topping saw and ground saws until the operator recognizes your presence.

Make sure that all equipment is shut down with the attachment resting securely on stable ground before advancing to the machine.

When mounting or dismounting the machine always use the 3 point technique; use 1 hand with 2 feet or 2 hands with 1 foot.

WARNING

Always avoid the discharge path of all saws.

Avoid mounting or dismounting the machine in areas with slippery surfaces. Dry, deice, clean up or cover slippery surfaces with an anti-slip material before mounting or dismounting the machine.

Wear a suitable hearing protective device such as earmuffs or earplugs to protect against noise.

Prolonged exposure to loud noise can cause impairment or loss of hearing.

Always use the handrails and steps provided when mounting and dismounting from the machine.

Do not jump off the machine at any time.

1.3

Safety

Tigercat T234B Loader Check protective windows for cracks, a damaged window has reduced strength to stop flying objects. All damaged windows must be replaced with original equipment.

Check windows for scratching, crazing and cloudiness that could impair clear visibility all around the machine.

Do not operate the machine with any defective or inoperable components.

WARNING Do not walk on machine surfaces with steel cleated foot wear. Steel cleats on steel surfaces are slippery and do not provide a safe foot hold.

Check all fluid levels.

Do not operate the machine with any of the exhaust system, safety covers, oil shields, or other devices removed.

WARNING It is not recommended to walk on machine surfaces that are not designated walking areas.

No attempt should be made to walk on angled steel surfaces or surfaces that are irregular in shape.

Keep a first aid kit in an easily accessible location on the vehicle at all times.

Walking surfaces on the machine must be covered with anti-slip materials to provide a safe foot hold and prevent slipping.

Working With Oil Direct contact with oil implies a risk of skin complaints (example: eczema). Strict hygiene should always be observed.

These anti-slip surfaces should be maintained on a regular basis. If the surface shows signs of wear, the anti-slip material must be replaced immediately.

Some advice which should be observed:

To reduce risk of fire, machines should be completely cleaned of debris at least daily, particularly around the engine exhaust components. Hydraulic oil leaks, excess grease, fuel and oil accumulation (including spillage) should be eliminated immediately, always shut off engine before cleaning machine.

•

Oils used in this machine may be hot enough to cause serious burns.

•

Avoid contact with oil, particularly heated oil.

•

Oil on the skin should be washed off immediately with soap and water.

•

Wear protective gloves. Hands should be clean before putting on gloves. Apply protective cream to the hands to make washing easier.

•

Don't put oily rags in your pockets.

•

Oil soiled clothing should be changed as soon as possible.

•

Always keep an extra overall handy, but not in the machine where it can become dirty.

•

Cuts and abrasions must be attended to immediately. Clean them and apply first-aid.

•

Avoid breathing in oil fumes.

•

Wash hands and arms frequently (example: at each meal break or as often as possible).

Maintain a clean cab interior, clear away trash or debris.

Machine should be washed completely at every major service.

Inspect the machine daily for signs of damage or unusual wear, to structures.

Check for fluid leaks, or faulty operation. Repair or replace malfunctioning parts and systems immediately.

Check windows and door guards for damage.

1.4

Tigercat T234B Loader

Safety

SAFETY HAZARDS – VITON SEALS

Approach with extreme caution any area where overhanging electrical power lines are present.

Serious injury or death by electrocution can result if the machine or any of its attachments are not kept a safe distance from these lines.

O-rings and other seals manufactured of Viton material (fluorine rubber) produce a highly corrosive acid (Hydrofluoric) when subjected to temperatures above 600°F (315°C).

Maintain a distance of 3 m (10 ft) between the machine or boom and any power line carrying up to 50,000 volts or less plus 12 mm (1/2 in) for each addition 1,000 volts above the 50,000 volt level.

This contamination can have extreme consequences on human tissue since it is almost impossible to remove after contact.

The following procedures are recommended when inspecting equipment that has been subjected to high temperatures such as fire: •

•

If State/Provincial, local or job site regulations require even greater safety distances than stated above, adhere strictly to these regulations for your own protection.

Visually inspect any seals or gaskets which have suffered from heat; they will appear black and sticky. If these are found, Do Not Touch!!!

If the machine must be transported, make sure that it is adequately secured to the transporting vehicle. Refer to Vehicle Moving Instructions page in SECTION 2.

Determine the material composition of any seals or gaskets, If fluoro-elastomer seals (Viton, fluorel, or tecmoflon) have been used, the affected area must be decontaminated before undertaking further work. Natural rubber and nitrile materials are not hazardous.

•

Wear disposable heavy duty gloves (neoprene) and decontaminate the affected area by washing thoroughly with limewater (Calcium Hydroxide solution).

•

Safely discard any cloths, residue and gloves after use.

Stopping the engine immediately after it has been working under load can result in overheating and premature wear of the engine components.

Reduce engine speed to LOW IDLE and let run for approximately 5 minutes to allow gradual dissipation of heat and also to reduce turbo speed. This will also prevent loss of coolant by after boil and possible hot spot damage to the engine.

NOTE: Burning discarded items is not recommended except in an approved incineration process where the dangerous products are treated by alkaline scrubbing.

SAFETY HAZARDS – OPERATING

Be aware when performing service and maintenance tasks that surfaces and grab handles in and around the engine and cooling system may become very hot when the engine has been running. Contact with hot surfaces may cause injury.

Maintain a charged fire extinguisher on the vehicle at all times and KNOW HOW TO USE IT. Do not carry passengers either in the cab or anywhere else on the machine. The vehicle is provided and approved with seating for the operator only.

Comply with instructions in this manual and also your company’s regulations for the operation of this machine.

Do not allow anyone to operate the machine who may not be physically fit or who may be under the influence of alcohol or drugs.

Read, understand and follow all general safety precautions specified by attachment manufacturer.

When moving the machine, watch that enough clearance is available on both sides and above the machine or any of its attachments. Extra clearance may be required particularly where the ground is uneven.

WARNING Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

1.5

Safety

Tigercat T234B Loader

Avoid Injury from Backover Accidents

WARNING

Before moving machine, be sure all persons are clear of the area.

Battery posts, terminals and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

Wash hands after handling.

Always be alert for bystanders moving into the work area. Use horn to warn bystanders before moving the machine.

When using a signal person, keep the person in view at all times. Always be sure the signal person is clear before backing up.

If acid is accidentally splashed into your eyes, flush immediately with clean water and get medical attention.

To avoid backover accidents:

Do not attempt to charge a frozen battery; it can explode.

Disconnect battery before working on electrical systems as follows: •

Turn off battery disconnect switch in engine enclosure.

•

Disconnect negative starter motor cable from both battery posts

•

Disconnect positive master solenoid cable from both battery posts

•

Always look around before you back up. Be sure that everyone is clear.

•

Keep motion warning alarm in working condition. The motion warning alarm must sound when the machine is moving in forward or reverse.

•

Use a signal person when backing up if view is obstructed. Always keep the signal person in view.

•

Learn the meaning of all flags, signs and markings on the job site and who is responsible for signaling.

•

Keep windows, mirrors and lights in good condition.

•

Dust, heavy rain, fog, snow etc. can reduce visibility. As visibility decreases, reduce speed and use proper lighting.

Connect ground terminal last when reconnecting.

Do not short out battery terminals for any reason.

Serious burns or an explosion can result.

CAUTION Lead-acid batteries contain sulfuric acid which can severely damage eyes or skin on contact. Always wear a safety face shield, rubber gloves and protective clothing to reduce risk of accidents.

Lead-acid batteries produce flammable and explosive gasses. Keep arcs, sparks, open flames and lighted tobacco a safe distance from the batteries.

1.6

Tigercat T234B Loader

Safety

OPERATING SAFETY PRECAUTIONS

D

41581AUNI R0

DEF (Diesel Exhaust Fluid) may irritate eyes or skin. Do not get in eyes. Do not get on skin.

Shut off engine when refuelling – DO NOT refuel the engine while smoking or near open flame or sparks.

First Aid treatment: DEF Contains Urea. If swallowed call a Poison Control Center or doctor immediately. Do not induce vomiting. If in eyes rinse with water for 15 minutes. If on skin rinse well with water. If irritation persists seek medical treatment.

Check that no other personnel have moved into a hazardous area before starting the machine.

Sound the machine horn before starting the machine.

WARNING Use only diesel exhaust fluid (DEF) which meets ISO 22241 specifications. NEVER fill the DEF tank with any other fluid.

DEF is injected into the exhaust gas stream during normal operation of the Selective Catalytic Reduction (SCR) aftertreatment system.

Use of other fluids may cause component damage, or a fire risk which could result in death or serious injury.

The operator’s seat is equipped with a lap belt.

Use the lap belt at all times when operating the machine.

Start the engine according to the instructions in this manual. Refer to OPERATING MACHINE in SECTION 2.

WARNING • EXPLOSION HAZARD. • DO NOT USE ETHER. • ENGINE EQUIPPED WITH HEATER STARTING AID. • USE OF ETHER COULD RESULT IN DEATH OR SERIOUS INJURY. 36782BENG R0

Never use a liquid staring aid to start an engine.

THIS MACHINE IS EQUIPPED WITH A COMPUTER CONTROLLED HEATING ELEMENT IN THE ENGINE INTAKE SYSTEM. STARTING FLUIDS WILL EXPLODE ON CONTACT WITH THE HEATING ELEMENT.

1.7

Safety

Tigercat T234B Loader SAFETY INTERLOCK SWITCH ON LEFT ARMREST

Before moving the machine to the work site, check to ensure that all doors, panels, and access covers are installed properly and secured.

The left arm rest is equipped with a safety interlock switch (1) to prevent the machine from being operated while the armrest is in the raised position (pilot system is shut off).

CAB EXITS There are 2 ways to exit the cab in case of an emergency.

1. Side Door – This is the main point of entry used under normal operating conditions to enter or leave the cab. This door is not equipped with a safety interlock switch and therefore when left open will not deactivate the pilot controls in the cab. The left armrest is equipped with a safety interlock switch that prevents machine operation when the armrest is raised. See SAFETY INTERLOCK SWITCH ON LEFT ARMREST for more details.

ALWAYS shut OFF engine before using the side door exit.

NOTE: The engine can be started but the machine functions cannot be operated with the left arm rest up.

INTERLOCK SWITCH SHOWN IN OFF POSITION WITH L.H ARMREST IN UP POSITION

2. Right Side Window – This is a second cab exit for use if the side door exit becomes blocked. This window is not equipped with a safety interlock switch and therefore when left open will not deactivate the pilot controls in the cab. ALWAYS shut OFF engine before using the side window as an escape hatch exit.

234-089

PILOT SYSTEM SHUT OFF

To operate: With the engine running and the left arm rest DOWN, push the pilot reset switch.

It is important that the operator of the machine be familiar with these emergency exits and how to use them.

All operators should practice using all the cab exits to become familiar with escape procedures should they need to perform them in the dark, when the machine is in a rolled position, or other possible adverse condition.

The exits should be checked to make sure that they are operational and will function in an emergency.

For additional information, refer to EMERGENCY EXITS in SECTION 2.

Once the safety interlock system has been activated, the safety of both the operator and all persons outside the cab becomes the responsibility of the operator.

The left arm rest safety interlock switch (pilot system shut off limit switch) and the pilot reset switch are a safety feature and their function must not be defeated in any way.

1.8

Tigercat T234B Loader

Safety

SELECTABLE MACHINE CONTROL ( OPTION) T234B-059

ROTARY SWITCH

WARNING

Maintain a safe operating distance between the machine and other personnel. Never operate the boom or attachment over the heads of bystanders.

SELECTABLE MACHINE CONTROL ROTARY SWITCH

Never travel near co-workers or other pieces of equipment with attachment running.

Do not allow people or other pieces of equipment near the harvesting operation.

WARNING

Do not turn on attachment until machine is at the harvesting site.

Use only prearranged and approved signalling practices.

Do not open an escape hatch or the cab doors to increase ventilation when operating the machine.

If the machine is equipped with selectable machine control check the position of the rotary switch to verify control response.

CAUTION

Before starting the engine, check to ensure that all doors, panels, and access covers are installed properly and secured.

Do not open cab doors or window screens when cab is on a slope. The doors and screens are heavy and could swing out with considerable force. Anyone in the path of swing could be injured.

Anyone opening the door or screen and holding on to it could be pulled out of the cab and injured.

Make sure that all of the controls are positioned as specified in the starting instructions in the operator's manual.

Sound the machine horn before starting the machine.

Never use a liquid starting aid to start an engine with a pre-heat device.

Keep the cab doors closed when driving or steering the machine to prevent accidental entry of branches and debris into the cab.

When the engine is running, DO NOT allow anyone in areas of the machine where they may be crushed by moving components.

Keep the cab doors closed and use seat belt when driving or steering the machine to prevent being thrown from the operator's cab.

Secure loose items in the cab.

Prior to commencing work, check all equipment controls to ensure that the machine responds correctly.

Make sure that all safety screens and guards including the skylight are installed and properly secured.

1.9

Safety

Tigercat T234B Loader WARNING

DO NOT operate this machine to lift or move any objects other than what it is designed to lift or move.

• Do not use the boom to service other equipment.

•

Do not use the boom to lift items such as tires, engines, cylinders, boom components, etc.

•

Do not modify the boom system.

•

Do not add hooks or lugs to the boom for the purpose of attaching lifting rigging.

•

Do not use the attachment for any purpose other than the intended function.

250D-076

BATTERY DISCONNECT SWITCH

Turn the battery disconnect switch off if the vehicle is to be idle for an extended period of time (Example – overnight).

Maintain a safe operating distance between the machine and workers and all other personnel. It is the duty of the operator to ensure that no person approach the machine while in use.

Failure to follow the above instructions could result in serious injury or death.

Always rest the attachment on the ground when operation is stopped, regardless if the engine is running or shut off.

Operate the machine only from a seated position in the operator’s seat.

Watch for ground hazards such as metal debris, wire fencing or rocks.

When travelling position attachment and boom so as not to impair vision.

If vision is limited by dust, smoke, fog, rain or snow, stop the machine until visibility is restored.

Park machine at least 15 m (50 ft) away from other equipment and in a cleared area. In the event of a fire, this distance will minimize the chance of the fire spreading to other equipment.

Before leaving operator's cab, lower the grapple onto solid ground, the trailer or carrier.

If out of the operator's cab for an extended period shut the machine off.

Never work alone. Regularly inform other crew members of your intentions, location and length of time to perform duties.

1.10

Tigercat T234B Loader

Safety

When parking the machine; •

Park on level ground only and engage the swing brake.

•

Do not park on a hillside or incline.

•

Take the machine out of DRIVE MODE. This will automatically engage the park brake.

•

Lower the attachment onto level ground.

•

Stop the engine.

•

Turn the machine battery disconnect switch off if the vehicle is to be parked for an extended period of time (Example – overnight).

NOTE: Wait 30 seconds after engine shut down before turning off battery disconnect switch. If battery disconnect is turned off before this the engine ECU (Engine Control Unit) will register a fault.

When transporting the machine watch that enough clearance is available on both sides and above the machine or any of its attachments to avoid contact with power or telephone lines, bridge structures, etc.

Before transporting the machine check to ensure that all doors, panels and access covers are installed properly and secured. Improperly secured doors or panels pose a serious danger to pedestrians and other vehicles.

NOTE: This machine is equipped with an After Run/ Accessory Relay which delays the power disconnect to engine related fuses and relays (ECU /ATS relay, NOx Sensor relay, NOx Sensor fuse, ECU Power fuse, DCU fuse). Whenever the engine is stopped all DEF solution is pumped back to tank before the engine power system is turned off. This process takes approximately 90 seconds.

Refer to AFTERTREATMENT SYSTEM in SECTION 3 for more information.

1.11

Safety

Tigercat T234B Loader

SERVICING SAFETY PRECAUTIONS

Before performing maintenance or repair work on any equipment, consult the manufacturer’s instruction manual and follow recommended procedures.

Conduct maintenance inspections at least as frequently as recommended in SECTION 3.

WARNING Diesel fuel or hydraulic fluid under pressure can penetrate the skin and cause serious personal injury, blindness, or death. If any fluid is injected into the skin, it must be surgically removed within a few hours by a doctor familiar with treating this type of injury.

250D-076

BATTERY DISCONNECT SWITCH

When servicing or repairing equipment, shut the engine down. Turn Battery Disconnect switch OFF and lock out the switch in accordance with local regulations. This machine is equipped with a remotely operated battery disconnect relay.

Some wiring on the machine is live even when the battery disconnect switch is off. When servicing the electrical system, remove the battery cables from the batteries disconnecting the negative cables first.

Never use your bare hand to check for fluid leaks.

Fluid leaks under pressure may not be visible.

When searching for leaks, wear work gloves and use a wrench or piece of wood to move hydraulic hoses. Do not grab hold of hydraulic hoses. Wear safety goggles for eye protection.

Install a 'DO NOT START ENGINE' sign on the operator’s cab door and in the engine compartment when making repairs to the machine.

Pressure can be maintained in a hydraulic system long after the power source and pump have been shut down. Lower the attachment to the ground, stop engine and relieve trapped pressure before performing work on components, or disconnecting any hoses. Accumulators will self-drain within 2 minutes of stopping the engine.

1.12

Tigercat T234B Loader

Safety Prior to welding on any part of the machine, the repair area should be cleaned and a fire extinguisher should be made available at the welding location.

The radiator and the engine cooling system should be cleaned and serviced daily to maintain moderate engine temperatures.

Care must be taken in attaching the welding machine grounding clamp so current does not pass through bearings, especially the swing bearing.

WARNING

Turn OFF the battery disconnect switch.

Disconnect the positive (+) and negative (-) battery cables from the batteries disconnecting the negative cable first.

WARNING, HOT FLUIDS AND HOT MACHINE SURFACES CAN CAUSE SERIOUS BURNS! •

Before servicing the machine, allow the engine cooling system, fuel system, exhaust system, hydraulic system and machine surfaces to cool down.

•

Use a thermometer to check surface and system temperatures to ensure it is safe to begin service work.

•

DO NOT begin service work until the surface or system temperature has cooled down to below 38°C (100°F)!

This machine is equipped with sensitive electronic control equipment, prior to welding:

630E-259

ENGINE CONTROL UNIT

Disconnect the engine ECU (Engine Control Unit) by unplugging the two multi-pin connectors.

XA2-A0 MODULE Disconnect the XA2-A0 module connector (under platform in valve compartment ).

1.13

Safety

234B-278

Tigercat T234B Loader

XA2-A1 MODULE COVER CAPSCREWS 2 BOTTOM 1 TOP (NOT SHOWN)

Disconnect the XA2-A1 module connector (mounted on same plate as the XA2-A0 but in engine compartment).

MD3 CONTROLLER Disconnect the MD3 controller in the cab.

Remove back cover from the MD3, held by 3 hex capscrews (1 top. 2 bottom) to access plugs.

NOx SENSOR ECU (OBSCURED)

250D-064

NH3 SENSOR ECU

NOx AND NH3 SENSOR ECU'S

Disconnect the NH3 sensor ECU and the outlet NOx sensor ECU both mounted on a bracket next to the radiator on the left side of the engine compartment.

234-108

XC21 MODULE

Disconnect the XC21 module(s) mounted in the cab fuse and relay panel.

INLET NOx SENSOR ECU

When welding is complete reconnect all multipin connectors. Attach the battery cables reconnecting the positive (+) cable first. Turn ON the battery disconnect switch.

250D-066

INLET NOx SENSOR ECU

Disconnect the inlet NOx sensor ECU mounted above the vacuum pump at the back of the hydraulic tank.

1.14

Tigercat T234B Loader

Safety

Use the proper tool for the job. Repair or replace worn or damaged tools including lifting equipment immediately.

Keep your hands, feet, head, and loose clothing away from power driven parts. Tie long hair behind your head. Remove rings and other jewelry to prevent electrical shorts and entanglement in moving parts.

Explosive release of fluids from pressurized cooling system can cause serious burns.

Shut off engine. Only remove coolant filler cap when cool enough to touch with bare hands.

Slowly loosen cap to first stop to relieve pressure before removing completely.

Always be aware of machine pinch points that could cause injury. Never place body parts within the range of motion of the working parts of the machine.

Never stand under an object supported with hydraulics. Always use safety stands or a locking device.

Before performing work under the boom system ensure it is firmly supported.

Do not change any pressure or relief setting unless Tigercat authorized instruction has been obtained.

When opening or closing power operated engine door, watch for personnel in door areas.

If the engine is running inside a building, ensure that sufficient ventilation is available to prevent a build-up of toxic exhaust fumes. Run the engine only when it is necessary for testing or adjustments.

WARNING DO NOT operate this machine to lift or move any objects other than what it is designed to lift or move.

• Do not use the boom to service other equipment.

•

Do not use the boom to lift items such as tires, engines, cylinders, boom components, etc.

•

Do not modify the boom system.

•

Do not add hooks or lugs to the boom for the purpose of attaching lifting rigging.

•

Do not use the attachment for any purpose other than the intended function.

Work in a ventilated area. If it is necessary to run an engine in an enclosed area, use an exhaust pipe extension to remove toxic exhaust fumes.

Maintain a safe operating distance between the machine and workers and all other personnel. It is the duty of the operator to ensure that no person approach the machine while in use.

Failure to follow the above instructions could result in serious injury or death.

If you don't have an exhaust pipe extension, either work outside, or open the shop doors.

1.15

Safety

Tigercat T234B Loader

Dispose of fluids properly. Do not pour fluids into the ground, stream, pond or lake. Before draining any fluids, know the proper way to dispose of them.

Read, understand and follow all operating safety precautions specified by the attachment manufacturer.

WARNING Always follow attachment manufacturer's instructions and safety warnings before approaching attachment head to make adjustments.

WARNING DO NOT work below or behind a machine that is parked on a grade.

WARNING Failure to follow all of the above instructions could result in serious injury or death from crushing.

1.16

Tigercat T234B Loader

Safety

FLUID INJECTION INJURY

As always the best defence against suffering the effects of fluid injection is to prevent the accident from occurring in the first place.

When searching for possible fluid leaks • NEVER search for leaks with your bare hands. Always wear thick protective gloves.

WARNING Diesel fuel or hydraulic fluid under pressure can penetrate the skin and could result in death or serious injury. If any fluid is injected under the skin, a medical doctor familiar with the treatment of this type of injury must surgically remove it within a few hours.

Hydraulic and diesel fuel systems on forestry machines operate at very high pressures, often 207 bar (3000 psi) and above. If a loose connection or a defect in a hose should occur, a fine, high velocity stream of fluid will result.

Even for systems pressurized to as little as 7 bar (100 psi), this fluid stream can penetrate human skin as if it were a hypodermic needle.

Initially, an accidental fluid injection beneath the skin may only produce a slight stinging sensation.

There is a danger that you will tend to ignore this, thinking that it will get better with time. Most often, it does not! Within a very short time the wound may begin to throb painfully, indicating that tissue damage has already begun.

Similarly fluid injected directly into a blood vessel can spread rapidly through your circulatory system. The human body has little ability to purge injected fluid.

Time becomes critical as tissue damage progresses rapidly. The longer you delay getting professional medical attention, the more damage can occur.

Although fluid injection accidents are rare, the resulting injury has on occasion required the amputation of a finger, a hand or in some cases the entire limb. The longer the delay in getting professional medical aid, the further up the limb the tissue damage can spread. An injury of this type can become very serious or even fatal if not dealt with promptly and properly.

In the event of any suspected fluid injection injury • Report the injury to your supervisor immediately.

•

Seek professional medical attention immediately.

1.17

•

Be sure to wear safety goggles for eye protection.

•

Keep all body parts well away from the area being investigated for leaks.

•

Use the end of a long piece of wood to move hoses or other obstacles.

•

Place the end of a long piece of wood in the suspected path of any fluid stream. Never use any part of your body.

•

Recognize that the source of the leak and the fluid streaming from it may be very small and not easily visible. You may only be able to see the fluid that accumulates as a result of the fluid stream.

•

When performing any service work

•

Stop the engine and relieve all diesel fuel or hydraulic pressure before disconnecting any lines or otherwise working on the system.

•

Never grab any hydraulic or diesel fuel connectors or hoses when they are subjected to pressure.

•

Always ensure that hoses are rated for the pressures to which they will be subjected.

•

Never use any hoses that you suspect could be defective.

Safety

Tigercat T234B Loader

GREASE INJECTION INJURY WHEN USING PNEUMATIC GREASE GUNS Pneumatic grease guns can deliver grease at pressures from 17 – 400 bar (246 – 5801 psi).

It takes less than 7 bar (100 psi) to inject a substance through human skin.

Always get professional medical treatment immediately after any type of injection injury.

Provide the physician with information on the type of grease, the pressure setting of the gun, and similar details.

The amount of fluid injected, type of fluid (or material), pressure at which it was injected, and the elapsed time between injection and surgery all influence the chances of successful treatment for this type of serious injury.

Prior to using a high pressure pneumatic grease gun perform the following: •

All operators of high pressure pneumatic grease guns MUST be trained in the hazards of its operations and the treatment for such injuries.

•

Do not operate a high pressure pneumatic grease gun unless you have been trained in the proper operation and are aware of all safety precautions of such a tool.

•

Wear protective clothing such as gloves, safety hat and safety glasses.

•

Inspect all parts of the grease gun for wear and tear and replace all worn or damaged parts.

•

Ensure that protective shrouds are installed on all grease gun nozzles as safety devices.

•

Remove dirt and grease from grease fittings prior to greasing.

•

Replace any defective grease fittings on equipment with new fittings immediately.

•

When badly positioned fittings are identified, replace them with angled or swivel fittings for easier access.

1.18

Tigercat T234B Loader

Safety LIGHTNING SAFETY

LIGHTNING SAFETY AWARENESS

In spite of the popular myth that being struck by lightning is an unlikely event, the facts show that lightning strikes occur frequently. As a result loggers are at high risk because their work is outdoors and close to known strike points such as tall trees and heavy equipment.

Loggers can increase their chances of avoiding a lightning strike by following a few simple safety practices.

1. Designate a member of your crew to • Monitor daily weather forecasts

WHAT IS A LIGHTNING STRIKE?

• Observe local weather conditions

Lightning is a discharge of the electricity produced by a thunderstorm. As the thunderstorm develops, many small particles of ice within the storm clouds bump together. These collisions create a positive charge at the top of a cloud and a negative charge at the bottom. As this continues a second positive charge builds up on the ground beneath the cloud, concentrated around high objects such as hills, trees, buildings, equipment and even people.

• Alert all other members of the crew when a possible lightning threat develops.

2. Don’t start or continue any work that cannot be stopped immediately, when a storm moves nearby.

3. Anticipate a high-risk situation and take action early by moving to a low-risk location. Do not hesitate. If there is lightning, you are in danger.

When the difference between the electrical charge in the cloud and on the ground becomes great enough to overcome the resistance of the insulating air between them, an electrical current flows instantly. This is a lightning strike.

4. Obey the rule – If you see lightning, Flee. If you hear thunder, Clear.

5. Do not follow the now obsolete guideline to take shelter when the time between seeing lightning and hearing thunder is 30 seconds or less. This does not provide sufficient time to ensure safety. Always follow step 4.

The electrical potential in a lightning strike can be as much as 100 million volts. Lightning strikes can occur over very large distances, even as much as 60 km (37 mi). Lightning travels both in front of and behind a thunderstorm and so strikes happen even when rain has not started or has stopped.

Lightning can hit in the same place, many times and often spreads out over 18 m (60 ft) within the soil around the strike point.

6. Remain in your safe location for 30 minutes after the last sight of lightning or the last sound of thunder.

The safest location during lightning activity is inside a fully enclosed, substantially constructed building, a house, office, school, shopping area, etc. These are the safest because of the electrical wiring and plumbing that they contain. Should lightning strike, the electrical current will travel through the wiring or plumbing into the ground.

When such a building is nearby, always seek shelter there first.

Thunder always accompanies lightning. When lightning occurs, the air through which it travels is instantaneously heated to a temperature more than 28,000°C (50,000°F). The air expands rapidly due to this heating, then quickly contracts as it cools. It is this contracting shock wave that we hear as thunder.

In many areas of the world, lightning strikes are second only to flooding as the greatest cause of storm related deaths and injuries. Although only 10% of lightning strike victims are killed, virtually all from cardiac or respiratory arrest, over 70% of those that survive suffer severe, life-long injury and disability. The symptoms of a lightning strike include memory loss, fatigue, chronic pain, dizziness, sleeping difficulty and the inability to complete several tasks at one time.

1.19

Safety

Tigercat T234B Loader WHAT TO DO IF YOU ARE OUTSIDE AND SEE LIGHTNING OR HEAR THUNDER. If you can, get inside.

1. Run to the nearest building, motor vehicle or fully enclosed ROPS equipment cab immediately. Being anywhere outside is not safe.

2. If inside a building: • Don’t watch the lightning storm from open windows or doorways. Stay in inner rooms.

Unfortunately loggers do not often work close to buildings and therefore other alternatives need to be considered.

• Stay well away from corded telephones, electrical appliances, lighting fixtures, radio microphones, electrical sockets and plumbing pipes and fixtures.

Sheds, weather shelters, hunting blinds, tents and other partially open or small structures are not safe against lightning strikes as they lack the electrically grounded components of larger buildings. They are intended for sun or rain protection only. Do not seek shelter from lightning strikes inside these structures.

3. If inside a motor vehicle or fully enclosed ROPS equipment cab: • Under no circumstances whatsoever step outside of the vehicle or off the equipment to move to another shelter. Very dangerous electrical pathways to ground may go through you.

The second safest location during lightning activity is inside a fully enclosed car, van, truck or bus with a metal roof and metal sides. The electrical energy of a lightning strike to these vehicles is carried to ground by the conducting outer metal surfaces. This is called the skin effect.

• Shut down all operation, turn off the engine, close all doors and raise all windows.

• Sit squarely in the seat with your hands in your lap and your feet flat on the floor mat.

Do not seek safety from lightning strikes in vehicles with fiberglass or plastic body shells or in convertible top vehicles. None of these are safe, as they do not offer skin effect lightning protection.

• Do not touch any metallic objects referenced to the outside of the vehicle. Do not touch any door and window handles, control levers, foot pedals, steering wheels, cab interior walls and any other inside to outside metal objects.

Heavy forestry equipment such as a skidder, loader, feller buncher, forwarder, etc. with a fully enclosed rollover protective structure (ROPS) cab take advantage of the skin effect and are therefore safe in electrical storms.

• Do not touch any radio or telephone connected to an outside antenna.

However machines with a rollover canopy only are not safe against lightning strikes as they are open to electrically conductive rainwater and do not benefit from the skin effect. Operators of this equipment must abandon their machines and get to a safer location before lightning strikes.

Note that the rubber tires on motor vehicles and heavy equipment do not increase safety from lightning strikes. Lightning has already travelled a great distance through the air to strike the vehicle.

In comparison a few inches of rubber in a tire offers absolutely no additional insulation.

1.20

Tigercat T234B Loader

Safety What to do if you feel your skin tingling, your hair stands on end, light metal objects vibrate or you hear a crackling sound.

1. Lightning is probably about to strike. You only have a few seconds to act.

2. Put your feet together. Crouch down like in a baseball catcher’s position. Hold your head down. Cover your ears to protect them against the noise of the thunder.

3. Do not lie flat on the ground. By touching as little of the ground as possible, the lightning may not move across the ground to you.

If you are caught outside and have no where else to go.

What to do if a co-worker has been struck by lightning.

1. Avoid wide-open areas where you project above the surrounding landscape.

1. The victim does not carry any electrical charge. There is no danger to anyone helping this person. You can touch him or her immediately.

2. Seek shelter in a low place, such as a ditch, ravine, valley, canyon or cave.

3. Get away from open water such as ponds or streams.

2. Call your local emergency response telephone number immediately.

4. Do not take shelter under any isolated tall trees or small groups of trees.

3. If the victim has no pulse, their heart has stopped or they have stopped breathing.

Start CPR or mouth-to-mouth resuscitation immediately. Use a portable defibrillator if one is available.

5. Seek shelter amongst the dense, thick growth of the shortest trees.

6. Avoid entering any small enclosures or shelters.

4. Be careful about staying in the storm to take care of the victim. You can get hit by lightning too. If you can, move the victim to a building as soon as possible.

7. Do not seek shelter under any motor vehicle or heavy equipment.

8. Keep clear of any materials that can conduct electricity such as wire fences and gates, metal pipes, poles, rails and tools.

To further increase your awareness about lightning safety, see the following web sites.

9. Stay at least 15 m (50 ft) away from metal objects such as a fuel tank, a vehicle or machinery without a cab, motorcycle, ATV, etc.

National Weather Service Lightning Safety http://www.lightningsafety.noaa.gov National Lightning Safety Institute http://www.lightningsafety.com

10. Stay at least 5 m (16 ft) apart from any other members of a group so that lightning won’t travel between you.

11. Do not use the telephone except for emergencies.

1.21

Safety

Tigercat T234B Loader 4. Clean out all accumulated forest debris (twigs, pine needles, branches, bark, leaves, saw dust, small wood chips) and any other combustible materials from inside the machine belly pans or lower machine structures as well as from areas in proximity to the engine, fuel and hydraulic oil systems no less frequently than at the completion of each work shift.

FIRE PREVENTION

5. Inspect the machine regularly for any signs of diesel fuel or hydraulic system leakage.

Check for worn or eroded fuel or hydraulic lines before starting up any equipment.

When working in a forest environment, it is impossible to prevent combustible debris from collecting in tight corners of the machine. This debris, in itself, may cause a fire; however, when mixed with fuel, oil or grease in a hot or confined place, the danger of fire is greatly increased.

6. Clean up any grease, diesel fuel, hydraulic and lubricating oil accumulation and spillage immediately.

The following fire prevention guidelines should be used to supplement the operator’s fire prevention efforts. In no case should the guidelines be used, or assumed, as replacements for diligent operator efforts at preventing fires.

7. Steam clean the engine, hydraulic pumps, transmission, brake, fuel and hydraulic tank compartments and all machine belly pans at least once a month or more frequently when working in logging conditions where large amounts of combustible forest debris are present.

The following guidelines will help to keep your equipment up and running efficiently and keep the risk of fire to a minimum.

8. Use only nonflammable solutions for cleaning the machine and components.

1. Maintain a charged fire extinguisher on the machine at all times and KNOW HOW TO USE IT.

9. Inspect the exhaust system daily for any signs of leakage. Check for worn, cracked, broken or damaged pipes or muffler. Also check for missing or damaged bolts or clamps. Should any exhaust leaks or defective parts be found, repairs must be made immediately. Engine exhaust leaks can cause fires. Do not operate the machine until the exhaust leak is repaired.

2. Remove debris and blow out dust regularly from the air intake doors, engine radiator and charge air cooler, hydraulic oil cooler, diesel fuel cooler and air conditioning condenser core to prevent overheating of the engine and hydraulics and to maintain efficient operation of the machine. Refer to CLEANING COOLER PACKAGE in SECTION 2.

10. During daily operation of the machine, the occurrence of exhaust leaks are usually accompanied by a change or increase in engine exhaust noise levels. These audible warnings cannot be ignored. Should any exhaust leaks occur during operation, the machine must be shut down immediately and not put back to work until the necessary repairs have been completed.

3. Blow off all forest debris and fine organic material accumulated near hot engine exhaust components (turbocharger and exhaust manifold as well as exhaust pipes and muffler) at the completion of each work shift or more frequently when working in logging conditions where large amounts of combustible forest debris are present. Visual inspection after blow off to ensure thorough cleanliness is vital. Engine exhaust systems provide numerous small pockets where saw dust, small wood chips and other flammable forest debris can gather. Even small accumulations close to hot exhaust components can ignite and smolder. If dislodged this smoldering debris can fall into other areas of the machine and thereby spread a fire.

11. Park the machine at least 15 m (50 ft) away from other equipment at the end of each shift.

12. Never leave the machine parked with boom, arch or blade suspended off the ground.

Should their supporting hydraulic hoses burn through during a fire, pressurized hydraulic oil may be injected into the fire and the boom, arch or blade will fall rapidly to the ground.

13. Turn the battery disconnect switch to OFF at shut down to de-energize all electrical circuits.

1.22

Tigercat T234B Loader

Safety WHAT TO DO TO PREPARE FOR A MACHINE FIRE

14. Remain with the machine for at least 45 minutes at the end of operations while the machine cools.

15. Remove all keys, lock equipment and fuel cap at the end of operations to reduce the risk of vandalism.

16. Be cautious when smoking. An open flame, a lighted cigarette, etc., should not be permitted around any vehicle, especially during fuelling operations or when the fuel system is open to the atmosphere or when servicing batteries.

17. AFTER transporting (trucking) a machine from one job site to the next, open all doors and access panels and blow off any debris that may have repositioned itself onto the engine and exhaust parts due to wind turbulence caused by the journey.

18. Before starting repair work, such as welding, the surrounding area should be cleaned and a fire extinguisher should be close by.

•

Prevent the fire from happening in the first place by ensuring that all machine systems are frequently inspected and always well maintained.

•

Ensure that any hand held fire extinguishers are charged and in working order. Fire extinguishers require routine care. Follow the manufacturer’s instructions for inspection and maintenance shown on the label of the fire extinguisher and in the extinguisher manufacturer's manual.

•

Ensure that any pressurized water systems on the machine (if applicable) are charged and in working order. Refer to PRESSURIZED WATER SYSTEM MAINTENANCE in SECTION 3.

•

Ensure that you have the proper fire extinguishers on site. Most fires involving mobile forestry equipment will be Class A or B.

•

Dry chemical extinguishers should be rated ABC and pressurized water extinguishers should be rated A.

•

Class A fires involve ordinary combustibles such as wood, cloth, paper, rubber and many plastics, Class B fires occur with flammable liquids such as diesel fuel, oil and grease and Class C fires apply to energized electrical equipment.

•

Ensure that the nozzle of any hand held extinguisher and pressurized water system available on the machine and at the work site fits within the fire extinguisher access holes in the doors of the machine.

•

Ensure that your fire detection system* is in working order. Refer to FIRE DETECTION SYSTEM in SECTION 2.

•

Ensure that your fire suppression system** is charged and in working order. Refer to FIRE SUPPRESSION SYSTEM in SECTION 2.

•

Ensure that you are familiar with the recommended procedures for fire contained in the emergency action plan of your company.

•

Ensure that you follow all national, state / provincial and local regulations dealing with fire fighting in effect in your specific geographic region. Regulations will vary from region to region but most will usually require that:

19. Store rags and other combustible materials in a safe, fireproof location.

20. Do not use the machine on top of or to push piles of burning timber. A machine fire will most probably result.

Equipment fires adversely effect your ability to log, may increase your insurance premiums dramatically, or prevent you from obtaining insurance coverage at all.

1.23

Safety

Tigercat T234B Loader WHAT TO DO WHEN A MACHINE FIRE OCCURS

Workers assigned to fire fighting duties must be physically capable of performing them safely and effectively.

If operating the machine when a fire occurs:

Workers designated to use fire fighting equipment as part of an emergency action plan must receive full and proper training from a qualified instructor.

1. Lower all working attachments to the ground.

2. Shut the engine off.

3. Activate the fire suppression system**.

Whenever portable fire extinguishers are provided for use in the workplace, training must be provided to familiarize workers with the general principles of fire extinguisher use and the hazards involved with fire fighting.

4. Radio or call for help. Be certain to report a fire immediately.

5. Exit the machine taking fire extinguisher and pressurized water system hose (if applicable) with you.

Training must be provided upon initial employment and at least annually thereafter.

•

•

6. At all times ensure your own personal safety and the safety of anyone that may be in the area. Approach any fire with extreme caution.

All fires can be very dangerous and life threatening.

Ensure that after you have received the training as outlined above, that you know how to use the fire extinguisher, the pressurized water system (if applicable) and the fire suppression system on your machine.

There is not enough time available to read instructions during a fire emergency.

7. Only if you can safely do so, turn OFF the battery disconnect switch.

Before deciding to fight the fire, be certain that.

Ensure that all information necessary for you to immediately contact all sources of help (local fire department, etc) in the event of a fire emergency is recorded and readily available at all times.

1. The fire is small and not rapidly spreading.

2. There is always a clear, safe escape route to your back.

3. You have received training in the use of the available fire extinguishing systems and are confident that you can operate them effectively.

4. If in any doubt about whether or not to fight the fire – DON’T. Instead stand well clear of the fire and wait for help to arrive.

5. Be aware that engine coolant , diesel fuel or hydraulic hoses could fail during a fire. If this happens, hot coolant, fuel or oil could possibly be ignited by the fire.

6. If possible a dry chemical fire extinguisher or fire suppression system** should be used first to fight a machine fire. Then immediately afterwards use the pressurized water hose supplied with the machine (if applicable) or a pressurized water extinguisher (if available). A fire suppressed by dry chemical may re-ignite from the heat retained by any debris or hot machine components in the area. The water will cool the area, reducing the chances of re-ignition.

1.24

Tigercat T234B Loader •

Safety

Use the PASS method. This is the most effective use of a fire extinguisher.

WHAT TO DO AFTER A MACHINE FIRE HAS OCCURRED

Pull the pin at the top of the extinguisher that keeps the handle from being pressed. Break the plastic seal as the pin is pulled.

•

Before returning the machine to work.

1. Ensure that the cause of the fire is determined and all appropriate repairs are completed.

Aim the nozzle at the base of the fire. Do not aim the nozzle at the flames. In order to put out the fire, you must extinguish the fuel, not the flames. Hose nozzles are often clipped to the extinguisher body. Release the hose before taking aim.

2. Ensure that the fire detection system* or the fire suppression system** is properly serviced and in working order (if applicable).

3. Ensure that all extinguishers used in fighting the fire are replaced or recharged.

Squeeze the handle to release the pressurized extinguishing agent. The handle can be released at any time to stop the discharge.

•

Sweep from side to sPide at the base of the fire until the fire is completely out or the fire extinguisher is empty.

Notify your equipment dealer and / or Tigercat Industries Inc. by completing an incident report, Tigercat form number 5101.

*NOTE: Fire detection systems are offered by Tigercat as an optional installation on some Tigercat product lines. Please disregard any references made to fire detection systems if not installed on your machine. ** NOTE: Dry chemical fire suppression systems are offered by Tigercat as an optional installation on some Tigercat product lines. Please disregard any references made to fire suppression systems if not installed on your machine.

20229A

TYPICAL FIRE EXTINGUISHER ACCESS HOLE

•

Place the nozzle of the fire extinguisher into the appropriate fire extinguisher access hole and discharge the extinguisher.

•

Only if you can safely do so, open the access panels to the machine in the area of the fire.

•

Failing all attempts to access the machine compartment, discharge the extinguisher through the mesh or any available openings on the machine.

•

Ensure that the machine and all components have cooled down sufficiently after a fire so that re-ignition does not occur.

•

Remain with the machine until help arrives.

1.25

Safety

Tigercat T234B Loader

DRY CHEMICAL CLEANUP PROCEDURES

2. In areas exposed to moisture, the dry chemical powder will combine with water to form a paste that is mildly acidic. Note that all surfaces covered by this dry chemical paste including electrical contacts are vulnerable to corrosive attack.

Both ABC dry chemical fire extinguishers and fire suppression systems discharge a chemical powder to extinguish the fire. The chemical makeup and the small particle size of the powder as well as the force of the discharge all contribute to the fire fighting capability. These same characteristics also permit the powder to penetrate into and fully cover all components in the vicinity of the discharge.

To neutralize the acidic paste on large surfaces, spray or wash these areas with a mixture of 3 parts hot water to 1 part baking soda. Allow this mixture to stand for several minutes before rinsing with warm water. Wash the area with a mild soap and water solution.

Rinse thoroughly with water. Blow-dry to remove all residual water.

The following are recommendations for the cleanup and neutralizing of areas exposed to dry chemical powder.

Workers performing this work should wear protective clothing, safety goggles and a fine particle dust mask to minimize their personal exposure to the dry chemical powder.

Cleaning of electrical contacts should be done using an electrical contact cleaner that has no flash or fire point and is non-corrosive and non-conductive such as CRC Contact Cleaner 2000.

Ensure that all electrical systems have been completely de-energized prior to any cleanup.

3. In areas exposed to heat during the fire, the dry chemical powder will melt forming a coating that cakes or crusts on all surfaces.

1. In areas of the machine that remained cool and dry during the fire, the dry chemical will stay in powder form.

To break down the caked dry chemical, spray or wash these areas with a 50/50 mixture of hot water and isopropyl alcohol. Allow this mixture to stand in place for several minutes.

Be certain to clean these areas immediately to prevent any settled residual powder from coming into contact with moisture whether through direct contact or humidity in the air.

The caked dry chemical when exposed to moisture is also mildly acidic. Therefore when the break down procedure has been completed, follow this immediately with the neutralizing procedure as described in Step 2.

Remove the powder residue by blowing off with air, sweeping, dusting or vacuuming using a HEPA filter capable of trapping the small dry chemical particles. Then wipe all surfaces with a damp cloth.

1.26

Tigercat T234B Loader

SAFETY LABELS

Safety READ OPERATOR'S MANUAL and USE THE SEAT BELT AT ALL TIMES

SAFETY LABELS The following safety labels must be periodically cleaned and inspected to ensure legibility is maintained. Replace any label that becomes illegible, damaged or removed.

OPERATOR'S MANUAL LOCATION

This label indicates the storage location of the operator's manual. This label is located on the outside of the operator's manual case inside the cab.

This label gives two messages.

The centre panel notifies the operator to always read the operator’s manual before operating the machine. Pay close attention to WARNINGS and HAZARD identifications.

Study all the safety messages in this manual and on the labels on the machine carefully.

The bottom panel notifies the operator that the operator's seat is equipped with lap belt. Use this restraint systems at all times when operating the machine. DO NOT ATTEMPT TO MOVE OR OPERATE the machine until the seat belt is fastened properly.

1.27

Safety

Tigercat T234B Loader

KEEP CLEAR

NO RIDERS

43424BUNI R0

This label warns persons outside the cab to keep clear of the machine while in use.

Always keep clear of an operating machine.

When approaching an operating machine on foot, stay at least 60 m (200 feet) away until the operator recognizes your presence. Make sure that all equipment has been shut down before advancing to the machine.

Maintain a safe operating distance between the machine and workers and all other personnel. It is the duty of the operator to ensure that no person approach the machine while in use, the risk zone is 60 m (200 feet).

NO RIDERS INSIDE OR OUTSIDE OF THE MACHINE . Do not carry passengers either in the cab or anywhere else on the machine. The vehicle seating accommodation is for one operator only.

Persons riding on the outside of the machine are subject to hazards such as falling off the machine, crush hazards, thrown object hazards and many other hazards WHICH COULD RESULT IN DEATH OR SERIOUS INJURY.

Before moving machine, be sure all persons are clear of the area.

Always be alert for bystanders moving into the work area. Use horn to warn bystanders before moving the machine.

If any person attempts to climb onto the machine during operation, STOP THE MACHINE IMMEDIATELY. Do Not Operate the machine until other personnel are a safe distance away from the machine.

When using a signal person, keep the person in view at all times.

1.28

Tigercat T234B Loader

Safety

ENTANGLEMENT HAZARD

CRUSH HAZARD

36779BUNI R0

This label warns of an ENTANGLEMENT HAZARD (rotating parts) zone.

This label warns of a DOWNWARD FORCE CRUSH ZONE caused by swinging or falling logs.

DO NOT PLACE HANDS OR FINGERS IN THIS AREA. Rotating parts such as pulleys, belts and drives can cause entanglement of body parts resulting in serious injury.

Approaching personnel are subject to crush injuries by falling or swinging logs which could result in death or serious injury.

DO NOT start the machine until other personnel are a safe distance away from the machine.

KEEP HANDS AND FINGERS CLEAR OF ROTATING BELT, DRIVE OR PULLEY! Before performing any service work on these parts or in this area, shut engine off and wait for rotating parts to come to a complete stop.

When the engine is running, DO NOT allow anyone in areas of the machine where they may be crushed by moving components.

Maintain a safe operating distance between the machine and workers and all other personnel. It is the duty of the operator to ensure that no person approach the machine while in use, the risk zone is 60 m (200 ft).

DO NOT attempt to service or work on the machine UNTIL THE LOAD IS REMOVED from the attachment, the VEHICLE IS IN THE PARKED POSITION and the ENGINE IS SHUT OFF.

1.29

Safety

Tigercat T234B Loader

ELECTROCUTION HAZARD!

CRUSH HAZARD

This label warns of a potential ELECTROCUTION HAZARD. Contact with electric lines WILL RESULT IN DEATH OR SERIOUS INJURY! Before beginning work in any area study the area thoroughly and become familiar with any potential hazards especially electrocution hazards from electric lines.

DO NOT MOVE ANY PART OF THE MACHINE OR LOAD WITHIN 3 m (10 ft) PLUS TWO TIMES LINE INSULATOR LENGTH OF ANY ELECTRIC LINES!

This label warns of the hazards related to tilting of the cab and the cab riser mounting.

The top panel of this label warns of a DOWNWARD FORCE CRUSH HAZARD caused by the cab tilting forward.

SLIPPERY SURFACE WHEN WET

Approaching personnel are subject to crush injuries when the cab is being tilted forward which could result in death or serious injury.

DO NOT tilt the cab until other personnel are a safe distance away from the machine.

The middle panel of this label warns of a MACHINE ROLL-OVER CRUSH HAZARD if the cab riser is not secured properly as indicated in the bottom panel.

DO NOT operate the machine unless the cab riser is secured properly. Failure to do so could result in death or serious injury.

This label warns of a slippery surface when wet.

Avoid mounting or dismounting the machine in areas with slippery surfaces. If this is not possible clean up or cover slippery surfaces with a non-slip material.

1.30

Tigercat T234B Loader CRUSH HAZARD

Safety CRUSH HAZARD

This label warns of the CRUSH HAZARD caused by the boom when it is not properly supported.

Never work under or near an unsupported boom or attachment. Contact with a falling boom COULD RESULT IN DEATH OR SERIOUS INJURY! This label warns of the CRUSH HAZARD caused by the cab tilting. It is located on the hoist boom mounting saddle.

Be sure that all personnel are clear when tilting the cab. Operating the cab tilt function with personnel in the crush zone COULD RESULT IN DEATH OR SERIOUS INJURY!

Always lower the boom to the ground so that the weight of the boom and attachment is resting on the ground. Properly support and brace boom and shut off engine before performing service work.

EMERGENCY EXIT, HAND TIGHTEN ONLY

Keep all personnel clear of the machine before operating the cab tilt function.

CRUSH HAZARD

This label indicates that the escape hatch can also be used as an emergency exit.

The label also indicates that the escape hatch knobs should be hand tightened only to allow for easy exit.

Ensure all exit locations are functioning properly.

Refer to ESCAPE HATCH EMERGENCY EXIT in SECTION 2.

Refer to SIDE DOOR AND ESCAPE HATCH EMERGENCY EXIT MAINTENANCE GUIDE in THIS SECTION. This label warns of the CRUSH HAZARD if using the controls without verifying the position of the selectable machine control switch if equipped.

Operating the cab controls without verifying the position of the selectable machine control switch COULD RESULT IN DEATH OR SERIOUS INJURY! 1.31

Safety

Tigercat T234B Loader

CRUSH HAZARD

EXPLOSION HAZARD

WARNING • EXPLOSION HAZARD. • DO NOT USE ETHER. • ENGINE EQUIPPED WITH HEATER STARTING AID. • USE OF ETHER COULD RESULT IN DEATH OR SERIOUS INJURY. 36782BENG R0

This label warns of an EXPLOSION HAZARD. The engine is equipped with a heater starting aid, DO NOT USE ETHER to assist in starting the engine.

USING ETHER COULD CAUSE AN EXPLOSION WHICH COULD RESULT IN DEATH OR SERIOUS INJURY.

This label warns of the CRUSH HAZARD caused by the delimber knives and that approaching personnel are subject to crush injuries by delimber knives WHICH COULD RESULT IN DEATH OR SERIOUS INJURY. Do Not Operate the machine until all personnel are a safe distance away from the machine.

FIRST AID KIT

The delimber knives will close automatically when the engine is shut down. Do Not approach the delimber arms until the engine is shut down and the delimber arms are closed.

Do not operate the machine when any personnel approach! If any person attempts to approach the machine during operation, STOP THE MACHINE IMMEDIATELY.

This label indicates a location in the cab for storage of a first aid kit.

ALWAYS be aware of the location of other personnel who are working in the area and be prepared to stop operations if they enter your working area without warning. Be prepared for this potential and take appropriate action if required!

1.32

Tigercat T234B Loader

Safety CHECK DAILY

FIRE PREVENTION!

In addition to the previous label this label is a reminder to check the machine daily for the possibility of debris build-up, leaks, damaged wires and hoses and take the necessary action required to clean up any debris accumulation, repair any leaks, damaged wires or hoses.

This label advises operator's of the following: Read understand and follow the FIRE PREVENTION GUIDELINES in this manual.

These guidelines provide all the necessary action required to preventing fires on this machine. DO NOT OPERATE THIS MACHINE until you have read these instructions and have performed any necessary maintenance required that will prevent the potential of a fire from starting on this machine.

The label also advises to check and ensure that all fire fighting devices are in good working order.

FIRE EXTINGUISHER ACCESS HOLE

It is also important to note that fire prevention inspections and maintenance MUST BE PERFORMED FREQUENTLY (several times per day). A clean combustible free machine as well as frequent inspections of the exhaust components, hydraulic hoses and electrical cables and performing any necessary repairs immediately will help prevent fires.

Maintain a CHARGED fire extinguisher on the machine at all times, know where it is and KNOW HOW TO USE IT!

This label indicates the location of each FIRE EXTINGUISHER ACCESS HOLE.

1.33

Safety

Tigercat T234B Loader

1.34

Tigercat T234B Track Loader SECTION 2 – CONTROLS AND OPERATION CONTENTS - SECTION 2

ISSUE 1.3, APRIL 2016

A

A/C ON/OFF SWITCH.............................................................................................................................. 2.17 AIR CLEANER.........................................................................................................................................2.91 AIR CLEANER UNLOADER VALVE........................................................................................................ 2.91 AIR CONDITIONER/HEATER.................................................................................................................. 2.17 AIR FILTER RESTRICTION INDICATOR................................................................................................. 2.91 AIR INTAKE SYSTEM AIR FILTER RESTRICTION SENSOR.................................................................................................2.91 COMPUTER ALERT MESSAGE..........................................................................................................2.91 AIR PRECLEANER.................................................................................................................................. 2.92 AM/FM STEREO RADIO/CD.................................................................................................................... 2.19 AUXILIARY POWER, 12V........................................................................................................................ 2.17 B

BATTERY COMPARTMENT..................................................................................................................... 2.84 BATTERY DISCONNECT SWITCH......................................................................................................... 2.84 C

CAB CONTROLS..................................................................................................................................... 2.10 SELECTABLE MACHINE CONTROL (OPTION)..................................................................................2.11 CAB TILTING PROCEDURE ELECTRIC PUMP.................................................................................................................................2.21 HAND PUMP........................................................................................................................................2.22 CARE OF MACHINE.............................................................................................................................. 2.101 CASE DRAIN STRAINER........................................................................................................................ 2.90 CELL PHONE HOLDER........................................................................................................................... 2.17 CHARGE PRESSURE FILTER................................................................................................................ 2.90 COLD WEATHER STARTING.................................................................................................................. 2.80 COMPUTER.............................................................................................................................................2.26 ADJUSTMENT MENU..........................................................................................................................2.32 OIL GRADE....................................................................................................................................... 2.36 OPERATOR MODE SELECTION..................................................................................................... 2.36 SAW AUTO RETRACT TIME............................................................................................................ 2.33 SAW FLOW ADJUSTMENT.............................................................................................................. 2.34 TOP SAW RETRACT TIME............................................................................................................... 2.33 ALERT MESSAGES.............................................................................................................................2.68 CRITICAL MESSAGES........................................................................................................................2.57 DATE/TIME ADJUSTMENT..................................................................................................................2.52 DISPLAY ADJUSTMENT......................................................................................................................2.51 ENGINE MENU.....................................................................................................................................2.31 ANTI-STALL...................................................................................................................................... 2.31 COLD IDLE FUNCTION.................................................................................................................... 2.31 METRIC OR IMPERIAL UNITS......................................................................................................... 2.31 INFO MENU PAGE...............................................................................................................................2.54 LOGS................................................................................................................................................2.55 MODULES......................................................................................................................................... 2.55 INFORMATION MODE.........................................................................................................................2.37 JOYSTICK FEEDBACK SCREEN........................................................................................................2.37 MAIN DISPLAY.....................................................................................................................................2.29 MAIN MENU.........................................................................................................................................2.38 ADJUST MENU................................................................................................................................. 2.39 AUTO CLEAN DURATION................................................................................................................ 2.49 AUTO CLEAN FREQUENCY............................................................................................................ 2.49 AUTO SLASHER SAW RETRACT TIME.......................................................................................... 2.44 COLD IDLE SPEED.......................................................................................................................... 2.46 DELIMBER STATUS......................................................................................................................... 2.43 2.1

Controls and Operation

Tigercat T234B Track Loader

ENABLE FAN AUTO CLEAN............................................................................................................ 2.48 GRAPPLE OPEN/CLOSE FINE CONTROL..................................................................................... 2.41 GRAPPLE SAW AUTO RETRACT TIME.......................................................................................... 2.45 GRAPPLE SAW STATUS.................................................................................................................. 2.42 HOIST BOOM CUSHION STATUS................................................................................................... 2.40 IDLE DOWN WAIT TIME................................................................................................................... 2.40 IDLE ENGINE SPEED...................................................................................................................... 2.47 MAX ENGINE SPEED...................................................................................................................... 2.47 STICK BOOM CUSHION STATUS................................................................................................... 2.41 TOP SAW AUTO RETRACT TIME.................................................................................................... 2.45 MD3 MESSAGES.................................................................................................................................2.56 ALERT MESSAGES (YELLOW)....................................................................................................... 2.68 CRITICAL MESSAGES (RED).......................................................................................................... 2.57 MEASURE MENU.................................................................................................................................2.50 MESSAGES ENGINE FAULT CODE MESSAGES - CRITICAL............................................................................. 2.59 MESSAGES - ALERT CHARGE FILTER FAULT.................................................................................................................. 2.70 DIESEL EXHAUST FLUID LEVEL <5%............................................................................................ 2.78 DIESEL EXHAUST FLUID LEVEL <10%.......................................................................................... 2.78 DIESEL EXHAUST FLUID LEVEL EMPTY....................................................................................... 2.78 DIESEL EXHAUST FLUID QUALITY................................................................................................ 2.77 ENGINE FAULT CODE MESSAGES................................................................................................ 2.69 ENGINE TORQUE DERATE ACTIVE............................................................................................... 2.70 ENGINE VOLTAGE HIGH................................................................................................................. 2.79 ENGINE VOLTAGE LOW.................................................................................................................. 2.79 HARDWARE FAULT - MD3............................................................................................................... 2.74 HARDWARE FAULT - XA2-A0.......................................................................................................... 2.76 HARDWARE FAULT - XA2-A1.......................................................................................................... 2.76 HARDWARE FAULT - XC21-A2........................................................................................................ 2.75 HARDWARE FAULT - XC21-A3........................................................................................................ 2.75 HOIST BOOM LIMIT SENSOR......................................................................................................... 2.72 HYDRAULIC OIL FILTER RESTRICTION........................................................................................ 2.71 JOYSTICK AXIS FAULT.................................................................................................................... 2.71 LOW FUEL LEVEL............................................................................................................................ 2.79 SELECTABLE MACHINE CONTROL............................................................................................... 2.73 STICK BOOM LIMIT SENSOR......................................................................................................... 2.72 SWING PEDAL FAULT...................................................................................................................... 2.74 WATER IN FUEL............................................................................................................................... 2.79 MESSAGES - CRITICAL AFTERTREATMENT SYSTEM ENGINE IDLE TOO LONG............................................................. 2.62 AFTERTREATMENT SYSTEM TECHNICAL FAILURE.................................................................... 2.62 DIESEL EXHAUST FLUID QUALITY................................................................................................ 2.63 ENGINE AIR FILTER RESTRICTION............................................................................................... 2.58 ENGINE COOLANT TEMPERATURE HIGH.................................................................................... 2.60 ENGINE FAULT CODE MESSAGES - CRITICAL............................................................................. 2.59 ENGINE OIL PRESSURE LOW........................................................................................................ 2.59 ENGINE OIL TEMPERATURE HIGH................................................................................................ 2.59 ENGINE STOP.................................................................................................................................. 2.60 HARDWARE FAULT - ENGINE......................................................................................................... 2.61 HARDWARE FAULT - MD3............................................................................................................... 2.60 HARDWARE FAULT - XA2-A0.......................................................................................................... 2.61 HARDWARE FAULT - XA2-A1.......................................................................................................... 2.61 HARDWARE FAULT - XC21-A2........................................................................................................ 2.60 HARDWARE FAULT - XC21-A3........................................................................................................ 2.61 HYDRAULIC OIL LEVEL LOW.......................................................................................................... 2.58 HYDRAULIC OIL TEMPERATURE HIGH......................................................................................... 2.58 2.2

Tigercat T234B Track Loader

Controls and Operation

MESSAGES - ERROR MODULE NO CONTACT ERROR.................................................................................................... 2.66 MODULE VREF ERROR.................................................................................................................. 2.65 PREFERENCES MENU.......................................................................................................................2.51 SCREEN SAVER ADJUSTMENT.........................................................................................................2.52 USB PORT............................................................................................................................................2.30 CONTROL PANEL -LEFT ARMREST...................................................................................................... 2.13 CONTROL PANEL -RIGHT ARMREST.................................................................................................... 2.15 COOLER PACKAGE, CLEANING.......................................................................................................... 2.100 COOLING FAN - SWITCH........................................................................................................................ 2.16 D

DEF (DIESEL EXHAUST FLUID)............................................................................................................. 2.86 DEF TANK................................................................................................................................................2.86 DIESEL EXHAUST FLUID (DEF) LEVEL WARNINGS............................................................................ 2.78 DIESEL EXHAUST FLUID (DEF) TANK................................................................................................... 2.86 DIESEL HEATER CONTROLS, OPTIONAL............................................................................................ 2.19 E

EMERGENCY STOP SWITCH................................................................................................................. 2.17 ENGINE COMPARTMENT....................................................................................................................... 2.84 ENGINE DIAGNOSTICS CONNECTION................................................................................................. 2.30 ENGINE FAULT CODE MESSAGES - CRITICAL.................................................................................... 2.59 ENGINE, RESTARTING AFTER ENGINE RUNS OUT OF FUEL............................................................ 2.97 ENGINE SPEED SWITCH....................................................................................................................... 2.14 ENGINE STARTING................................................................................................................................. 2.96 ENGINE STOPPING................................................................................................................................ 2.99 F

FAN - VENTILATION................................................................................................................................ 2.18 FILTER CAB......................................................................................................................................................2.18 CHARGE PRESSURE, SWING PUMP................................................................................................2.90 HYDRAULIC RETURN.........................................................................................................................2.89 PILOT....................................................................................................................................................2.89 FIRE EXTINGUISHER............................................................................................................................. 2.18 FOOT PEDAL, SWING............................................................................................................................. 2.12 FUEL, REFUELING.................................................................................................................................. 2.85 FUEL TANK AND FILLER......................................................................................................................... 2.85 FUSES AND RELAYS CAB......................................................................................................................................................2.81 ECM FUSE...........................................................................................................................................2.83 ENGINE COMPARTMENT...................................................................................................................2.82 G

GAUGES AND ALARMS.......................................................................................................................... 2.83 H

HAND FILL PUMP.................................................................................................................................... 2.88 HORN.......................................................................................................................................................2.17 HOT WATER SHUT OFF VALVE............................................................................................................. 2.18 HYDRAULIC OIL HAND FILL PUMP................................................................................................................................2.88 HYDRAULIC OIL LOW LEVEL SWITCH..............................................................................................2.87 HYDRAULIC OIL LOW LEVEL WARNING...........................................................................................2.87 LOW HYDRAULIC OIL WARNING.......................................................................................................2.87 RETURN DIFFUSERS/STRAINERS....................................................................................................2.90 TANK.....................................................................................................................................................2.87 HYDRAULIC PILOT FILTER.................................................................................................................... 2.89 HYDRAULIC RETURN FILTERS............................................................................................................. 2.89 I

ICONS, PICTOGRAM DESCRIPTIONS.................................................................................................... 2.5 INSTRUMENT PANEL DIESEL HEATER CONTROLS, OPTIONAL.........................................................................................2.19 K

2.3

Controls and Operation

Tigercat T234B Track Loader

KEY SWITCH...........................................................................................................................................2.17 L

LIGHT - DOME......................................................................................................................................... 2.19 LIGHTS - SERVICE LIGHT SWITCH............................................................................................. 2.15, 2.16 LIGHTS - WORK LIGHT SWITCH........................................................................................................... 2.15 M

MACHINE OPERATION........................................................................................................................... 2.93 MACHINE PREPARATION............................................................................................................. 2.98, 2.99 MD3 COMPUTER.................................................................................................................................... 2.26 MD3 COMPUTER MAIN MENU............................................................................................................... 2.29 P

PANEL, CONTROL........................................................................................................................ 2.13, 2.15 PICTOGRAM DESCRIPTIONS.................................................................................................................. 2.5 PILOT SYSTEM LIMIT SWITCH.............................................................................................................. 2.14 PRECLEANER, AIR................................................................................................................................. 2.92 PRE-START CHECKS............................................................................................................................. 2.93 PUMP, HAND FILL, HYDRAULIC OIL...................................................................................................... 2.88 R

RADIO 2 WAY..........................................................................................................................................2.19 REFUELING.............................................................................................................................................2.85 S

SEAT........................................................................................................................................................2.24 SELECTABLE MACHINE CONTROL (OPTION)..................................................................................... 2.20 STARTING THE ENGINE......................................................................................................................... 2.96 STOPPING THE ENGINE........................................................................................................................ 2.99 STRAINER, CASE DRAIN....................................................................................................................... 2.90 T

TANK, DEF...............................................................................................................................................2.86 TANK, HYDRAULIC OIL........................................................................................................................... 2.87 U

USB PORT - MD3 COMPUTER............................................................................................................... 2.30 V

VACUUM SWITCH, HYDRAULIC TANK........................................................................................ 2.13, 2.15 W

WAIT TO START...................................................................................................................................... 2.79 WINDOWS................................................................................................................................... 2.19, 2.101 CARE OF POLYCARBONATE WINDOWS........................................................................................2.101 CAUTIONS......................................................................................................................................2.103 CLEANING INSTRUCTIONS.......................................................................................................... 2.103 CONCEALING HAIRLINE SCRATCHES........................................................................................ 2.103 FIRE PRECAUTIONS..................................................................................................................... 2.104 GRAFFITI REMOVAL...................................................................................................................... 2.104 INSPECTION AND MAINTENANCE............................................................................................... 2.102 RESISTANCE TO CHEMICALS...................................................................................................... 2.102 RESISTANCE TO WATER.............................................................................................................. 2.102 WINDSHIELD WASHER FLUID............................................................................................................... 2.19 WINDSHIELD WIPER/WASHER............................................................................................................. 2.19

2.4

Tigercat T234B Track Loader

Controls and Operation

PICTOGRAM DESCRIPTIONS Diagrams in pictorial form are used to represent machine function operation. Some of the symbols are signs, characters, figures, or any components related to the operation of the machine. They are a simple universal language of symbols or pictograms that illustrate a function or component without the use of words. Pictograms are installed on or in close proximity to the switch or device used to activate or deactivate the machine function or they may be a sign used on a warning or indicator light of a function that is operating or advising of an alarm condition.

Examples of these pictograms are the turtle speed such as SLOW =

or FAST =

and the rabbit

that are often used to describe

.

The pictograms used on this machine are as follows: = ACCEPT

= Boom IN, Stick

= ADJUSTMENT Menu Icon

= Boom OUT, Stick

= Air Conditioner ON

= Boom IN, Heel

= Air Conditioner OFF = Boom OUT, Heel = Air Intake Pressure, BOOST = Brake Pedal = Air Source, FRESH AIR

= Butt Board DOWN

= Air Source, RECIRCULATE

= Butt Board DOWN

= ALERT Message Symbol

= Delimber CLOSE

= Auxiliary Power Outlet 12 V

= Delimber OPEN

= Auxiliary Power Outlet 24 V

= Check, visually

= Battery CONNECT and VOLTAGE = Cigarette Lighter, 24 Volt

= Battery DISCONNECT

= Boom DOWN, Hoist

P

= Control Lever Multiple Direction

P

= Control Lever One Direction

= Boom UP, Hoist 2.5

= Control Lever Two Direction

Controls and Operation

Tigercat T234B Track Loader

= CRITICAL ERROR Message

= Engine BOOST PRESSURE

= CRITICAL Message

= Engine AIR INTAKE PRESSURE (Engine AIR FILTER RESTRICTED)

= DEF (Diesel Exhaust Fluid)

= Engine Charge Air TEMPERATURE

= DEFROST, Front Window = Engine Coolant TEMPERATURE = Delimber CLOSE = Engine DIAGNOSTICS = Delimber OPEN = Engine Emission Filter = Differential Locks

= Engine Emission Filter OFF

= Differential Lock ON

or

= Differential Lock OFF

= Engine Emission System TEMPERATURE

= ENGINE MENU Icon

= Drive Mode = Engine Oil PRESSURE = Drive FORWARD

= Engine Oil TEMPERATURE = Engine - PERCENTAGE OF LOAD

= Drive REVERSE

= Engine RUN = Drive Motor SPEED = Engine SPEED - RPM = Drive Pressure, FORWARD = Engine START = Drive Pressure, REVERSE = Engine STOP = Engine ANTI-STALL

2.6

Tigercat T234B Track Loader

Controls and Operation = Fuel TEMPERATURE

= Engine THROTTLE

= Fuel - WATER IN FUEL

= Engine TURBOCHARGER BOOST PRESSURE

= Fuel Level LOW

= Engine WAIT TO START

AUTO

= Engine WARNING

= Grapple CLOSE

= Engine WARM UP

= Grapple OPEN

= Fan AUTO REVERSING/CLEANING

= Grapple ROTATE CLOCKWISE

= Fan Full ON = Grapple ROTATE COUNTERCLOCKWISE

= Fan Reverse CLEAN

= Horn

= Fan SPEED

= Hours - MACHINE

= Fan - Ventilation Blower

= Hours - ENGINE

= Flow Adjustment

= Hydraulic TANK

= Fluid Level HIGH

= Hydraulic Oil CASE DRAIN

= Fluid Level LOW

= Hydraulic Oil GRADE

= Foot Pedal Control = Fuel CONSUMPTION RATE

= Hydraulic Oil LEVEL

= Fuel - DIESEL

= Hydraulic Oil LEVEL LOW

= Fuel Heater

= Hydraulic Oil TEMPERATURE

= Fuel Information

= Hydraulic Oil TEMPERATURE HIGH

= Fuel Reset and Trip fuel information 2.7

Controls and Operation

Tigercat T234B Track Loader

= Hydraulic System Pressure, LOAD SENSE

= Saw, Grapple, CUT

= Hydraulic Tank VACUUM

= Saw, Circle

= Imperial/Metric Toggle Symbol

= Saw, Circle, CUT

= Information Menu Icon

= Saw, Circle, ADJUSTMENTS

= Information Message Symbol

= Saw, Circle, AUTO RETRACT TIME

= Instrument BULB TEST

= Saw, Circle RETRACT = Saw, Slasher

= Joystick and Switches

= Saw, Slasher, CUT

= Lights, WORK

= Saw, Slasher, RETRACT

= Lights, ENGINE SERVICE

= Saw, Slasher, AUTO RETRACT TIME = Lights, REAR = Saw, Top

= Oil Cooler BYPASS

= Saw, Top, RETRACT

= Operator = Park Brake

= Saw, Top, AUTO RETRACT TIME

= No Park Brake

= Serial Number

= Pilot System ON (Reset)

= Speed CREEP or VERY SLOW

= Pilot System OFF

= Speed FAST or HI

= Remote Hydraulic Cylinder EXTEND

= Speed SLOW or LOW

= Remote Hydraulic Cylinder RETRACT 2.8

Tigercat T234B Track Loader

Controls and Operation

= Stabilizer DOWN

= Stabilizer UP = Steer RIGHT

= Steer LEFT = Switch ON = Switch OFF = Swing brake

= Swing CLOCKWISE

= Swing COUNTERCLOCKWISE

= Temperature

= Transmission

= Transmission, 1ST GEAR

= Transmission, 2ND GEAR

= Transmission Oil LEVEL = Vacuum = Variable Speed = Ventilation Blower Fan = Windshield Washer 2.9

Controls and Operation

Tigercat T234B Track Loader

CAB CONTROLS IMPORTANT: This manual is applicable to factory installed machine functions and controls. It does not take into account any changes or modifications made after shipment. Verify all functions before operating this machine.

NOTE: All joystick and Foot Pedal controls require that the pilot system be activated for the controls to function. Refer to PILOT RESET in THIS SECTION. Machines with delimber, slasher saw, grapple saw and live heel 1

250D-001

250D-001A

1A. JOYSTICK LEVER - LEFT

2

2A. JOYSTICK LEVER - RIGHT

Hoist Boom

Stick (Jib) Boom

Push the joystick lever forward to LOWER the Hoist Boom.

Push the joystick lever forward to move the Stick Boom IN.

Pull the joystick lever back to RAISE the Hoist Boom.

Pull the joystick lever back to move the Stick Boom OUT.

Grapple Open

Grapple Rotate Counterclockwise

Move the joystick lever to the left to OPEN the grapple arms.

Move the joystick lever to the left to rotate the grapple COUNTERCLOCKWISE.

Grapple Close

Grapple Rotate Clockwise

Move the joystick lever to the right to CLOSE the grapple arms.

Move the joystick lever to the right to rotate the grapple CLOCKWISE.

LEFT HAND JOYSTICK BUTTONS (SWITCHES) BOTTOM LEFT BUTTON - Delimber Open

RIGHT HAND JOYSTICK BUTTONS (SWITCHES) TOP LEFT BUTTON - Grapple Saw Extend (cut)

Push the bottom left button to OPEN the delimber.( This enables the Slasher Saw when the saw is activated)

Push the top left button to EXTEND (cut) with the grapple saw (if equipped).

BOTTOM RIGHT BUTTON - Delimber Close Push the bottom right button to CLOSE the delimber. ( This enables the Top Saw when the saw is activated) FRONT TRIGGER - Heel Boom In Push on front trigger button to tilt the heel IN.

BOTTOM LEFT BUTTON - Slasher Saw or Top Saw Extend Push the bottom left button to EXTEND (cut) with the slasher saw when the delimber is open and with the top saw when the delimber is closed.

Bottom Right Button - Slasher Saw and Top Saw Retract Push the bottom right button to RETRACT the slasher saw and top saw.

2.10

FRONT TRIGGER - Heel Boom Out Push on front trigger button to tilt the heel OUT.

Tigercat T234B Track Loader

Controls and Operation

Machines with delimber, slasher saw, grapple saw and live heel with Selectable Machine Control (Option). Example below is with the rotary switch turned to the right.

250D-001A

250D-001

2

1

2B. JOYSTICK LEVER - RIGHT

1B. JOYSTICK LEVER - LEFT Stick (Jib) Boom

Hoist Boom

Push the joystick lever forward to move the Stick Boom OUT.

Push the joystick lever forward to LOWER the Hoist Boom.

Pull the joystick lever back to move the Stick Boom IN.

Pull the joystick lever back to RAISE the Hoist Boom.

Swing Left/Right

Heel Boom In/Out

Move the joystick lever to the left to swing the upper structure to the LEFT (COUNTERCLOCKWISE).

Move the joystick lever to the left to tilt the heel IN.

Move the joystick lever to the right to swing the upper structure to the RIGHT (CLOCKWISE).

LEFT HAND JOYSTICK BUTTONS (SWITCHES) TOP LEFT BUTTON - Delimber Open

Move the joystick lever to the right to tilt the heel OUT. RIGHT HAND JOYSTICK BUTTONS (SWITCHES) TOP LEFT BUTTON - Slasher Saw or Top Saw Extend

Push the top left button to OPEN the delimber. ( This enables the Slasher Saw when the saw is activated)

Push the top left button to EXTEND (cut) with the slasher saw when the delimber is open and with the top saw when the delimber is closed.

TOP RIGHT BUTTON - Delimber Close Push the top right button to CLOSE the delimber. ( This enables the Top Saw when the saw is activated) BOTTOM LEFT BUTTON - Grapple Rotate Counterclockwise

TOP RIGHT BUTTON - Slasher Saw and Top Saw Retract Push the top right button to RETRACT the slasher saw and top saw.

BOTTOM LEFT BUTTON - Grapple Close

Push the bottom left button to rotate the grapple COUNTERCLOCKWISE

Push the bottom left button to CLOSE the grapple arms.

BOTTOM RIGHT BUTTON - Grapple Rotate Clockwise

BOTTOM RIGHT BUTTON - Grapple Open

Push the bottom right button to rotate the grapple CLOCKWISE

Push the bottom right button to Open the grapple arms.

FRONT TRIGGER - Grapple Saw Extend (cut) Push on the front trigger button to EXTEND (cut) with the grapple saw (if equipped).

2.11

Controls and Operation

Tigercat T234B Track Loader

RH TRACK DRIVE FWD/REV

LH TRACK DRIVE FWD/REV SWING RIGHT

SWING LEFT

T234B-015

FOOT PEDALS

3. FOOT PEDALS - SWING AND TRACK Depress the Left foot pedal to SWING LEFT. Depress the Right foot pedal to SWING RIGHT. Depress the LH track foot pedal with the TOE or push FORWARD on the lever to place the LEFT track in FORWARD drive mode.

Depress the LH track foot pedal with the HEEL or pull BACK on the lever to place the LEFT track in REVERSE drive mode.

Depress the RH track foot pedal with the TOE or push FORWARD on the lever to place the RIGHT track in FORWARD drive mode.

Depress the RH track foot pedal with the HEEL or pull BACK on the lever to place the RIGHT track in REVERSE drive mode.

NOTE: If the selectable machine control option is installed the swing can also be controlled by the left joystick. See CAB CONTROLS in THIS SECTION.

2.12

Tigercat T234B Track Loader

1

2

Controls and Operation

4

3

234B-009

CONTROL PANEL -LEFT ARMREST The control panel is located in the LH armrest on the seat. The following machine functions are controlled by switches located on this control panel:

VACUUM SWITCH

1. INTERIOR LIGHT SWITCH This is a two position switch to turn the cab interior light on and off.

2. VACUUM SWITCH, HYDRAULIC TANK The machine is equipped with a vacuum pump to “hold” the oil in the hydraulic tank when work is being done on the hydraulic system. This eliminates the need to drain the hydraulic tank before servicing pumps and other hydraulic components.

Switch in cab This switch will not function if the battery disconnect switch is turned off. Push the top of the switch to put it in the ON position to activate the vacuum pump.

2.13

FRONT ENGINE COMPARTMENT In engine compartment This switch is "unswitched" and will function even with the battery disconnect switch in the off position. Push the right hand side of the switch to put it in the ON position to activate the vacuum pump.

234E-273

Controls and Operation

Tigercat T234B Track Loader 4. PILOT RESET SWITCH

3. THROTTLE CONTROL

This function is provided to prevent accidental or improper use of the controls from anywhere but the operators seat.

This is a three position 'momentary' switch connected into the engine CPU circuit to adjust the engine rpm between the (IDLE) and (FULL) throttle set points.

With the engine running and the LH arm rest DOWN, push this switch to REACTIVATE the pilot system after it has been deactivated by raising the LH arm rest, or by turning the Key switch to the OFF position.

NOTE: Engage the pilot reset to increase engine speed. When the system is deactivated the engine speed will reset to minimum rpm.

PRESS and HOLD this switch in the position to increase engine speed (rpm).

Release switch at desired rpm or continue to HOLD to place engine at the correct FULL throttle setting.

5

PRESS and HOLD this switch in the position to decrease engine speed (rpm).

Release switch at desired rpm. or continue to HOLD to place engine at the correct MINIMUM throttle setting.

NOTE: All operations should be performed at FULL throttle.

Maintaining Correct Engine rpm 234-089

It is most important that the IDLE and FULL rpm of the engine be correct at all times:

LH ARMREST SHOWN IN UP POSITION

5. ARM REST SWITCH When the LH arm rest is placed in the UP position, a limit switch shuts OFF the pilot system DEACTIVATING all operating functions. When the LH arm rest is placed in the DOWN position, the limit switch closes and turns the pilot system ON. The operating functions are not REACTIVATED until the PILOT RESET switch is pressed.

IDLE - 1000 - 1250 rpm (No Load) Factory Default is 1200 rpm FULL - 1600 to 2200 rpm max. (No Load) Factory Default is 2000 rpm RATED WORKING — ­ 2200 rpm NOTE: At start-up the engine will always default to IDLE. The above values are with the hydraulic and engine oil at normal operating temperatures and no functions activated. These values are pre-set into the engine CPU (computer) and cannot be adjusted without the proper electronic programming software equipment.

Auto Idle Down If the engine is set to run at full throttle and no functions are activated for 10 seconds, the engine will idle down. The engine will return to the set idle speed as soon as a function is activated.

2.14

Tigercat T234B Track Loader

8

Controls and Operation

7

2 5

1

4 3 6

CONTROL PANEL - RIGHT ARMREST

4. WORK LIGHTS

The control panel is located in the R.H. armrest on the seat. The following machine functions are controlled by switches located on this control panel:

This switch controls the work lights located on the front of the cab and on the stick boom.

The circuit draws current directly from the battery and is protected by a fuse located in the fuse box.

1. CIRCLE SAW SWITCH (OPTION)

5. SERVICE LIGHTS

This is a two position ON /OFF switch.

Placing this switch in the ON position will turn on the CIRCLE SAW.

This switch controls the service light located in the engine enclosure. The circuit draws current directly from the battery and is protected by a fuse located in the fuse box.

2. HORN SWITCH Depress this rocker switch to sound the horn.

6. DRIVE MODE

3. DRIVE SPEED SWITCH

Placing this switch in the DOWN position will prevent the loader from being accidentally driven while loading or unloading.

Two drive speed ranges are possible. LOW position will provide a slow driving speed.

HIGH position provides a faster speed with reduced driving torque.

Place this switch in the UP position to drive the machine.

Place this switch in the LOW position when maneuvering around the loading area.

The HIGH position should only be used with the loader on flat solid ground. A flat bed trailer should be used to transport the loader over greater distances.

2.15

Controls and Operation

Tigercat T234B Track Loader In addition and if enabled, when this switch is in the AUTO position, the system will automatically run an auto clean cycle as per the frequency setting.

7. SWING BRAKE SWITCH This is a two position ON/OFF switch. Placing this switch in the ON position will apply the swing brake and prevent the upper structure from turning. The brake is also engaged whenever the pilot system is shut off (left armrest in raised position), but as an added safety precaution, the brake should always be applied with this switch when leaving the cab.

The swing brake is a spring apply, hydraulic release, multi disc brake.

The auto clean cycle is adjustable through the computer control system menu Refer to COMPUTER ~ MAIN MENU - AUTO CLEAN FREQUENCY in THIS SECTION.

8. COOLING FAN - SWITCH (IF EQUIPPED - VARIABLE PITCH FAN) This is a three position switch, labelled AUTO FULL ON / AUTO / CLEAN. This switch along with the MD3 computer system, controls the pitch of the engine cooling fan.

AUTO - AUTOMATIC POSITION - AUTO is the normal operating position for the fan control switch. When the switch is in the AUTO position, the fan will operate completely in an automatic mode. The computer control system will automatically control the fan pitch to minimize system energy losses and improve performance based on the temperature of the charge air, engine coolant and hydraulic oil.

The computer system automatically adjusts fan air flow to the minimum required level to maintain optimal operating conditions.

Automatic control of fan air flow to match your operating conditions can lower fuel consumption and reduce operating costs. In high temperature operating conditions the fan air flow is increased to improve cooling ability and efficient operation of the cooling assembly and air conditioning systems. In low temperature operating conditions fan air flow is reduced, as less cooling is required for efficient operation of the cooling system.

Note that when the switch is in the AUTO position and the fan air flow has stopped due to low charge air, engine coolant and hydraulic oil temperatures, turning ON the A/C will cause the computer system to immediately place the fan blades at a pitch to provide 30% air flow. This is to ensure that sufficient air flow is available for the cab A/C even while the machine is still warming up.

FULL ON (OVERRIDE) UP POSITION When the switch is in the FULL ON position, the computer control system is overridden and the fan will run at FULL air flow (blades pitched to 100%), for cooling regardless of charge air, engine coolant or hydraulic oil temperatures. Normally the fan control switch is placed in the AUTOMATIC position for optimal cooling. The FULL ON position is intended for use in the event of a temporary failure of the control system.

CAUTION Before placing the fan switch in the CLEAN position make sure that there are no personnel near the REAR of the machine in the area where the fan will expel debris.

CLEAN - DOWN POSITION - Momentarily pressing the switch to the CLEAN position will manually start the automatic clean cycle, reversing the flow of air (there is no need to hold the switch down). The pitch of the fan blades is changed and the direction of airflow through the engine enclosure is reversed. The change in airflow will blow debris from the radiator and reduce the risk of overheating and poor engine performance caused by a clogged radiator. When the CLEAN cycle is complete the fan automatically returns to normal air flow direction.

The auto clean cycle is adjustable through the computer control system menu Refer to COMPUTER ~ MAIN MENU - AUTO CLEAN FREQUENCY and AUTO CLEAN DURATION in THIS SECTION. It is also important to manually clean debris from the machine on a regular basis to maintain low machine operating temperatures.

Refer to COOLER PACKAGE, CLEANING in THIS SECTION.

2.16

Tigercat T234B Track Loader

Controls and Operation 11. 12-VOLT AUXILIARY POWER Two 12-volt outlets with 20-amp capacity for portable devices such as phones.

12. CELL PHONE HOLDER An adjustable cell phone holder.

13. MD3 DISPLAY MD3 Display. See MD3 Computer for more detail.

13 12

B

10

C

A

11 9

234B-011

A/C HEATER CONTROL PANEL

14. AIR CONDITIONER/HEATER 234B-013

The controls on this panel are used to adjust the heating and air conditioning temperature for operator comfort in the operator's cab.

MAIN DISPLAY CONTROL PANEL

9. EMERGENCY STOP SWITCH When the emergency stop switch is pressed DOWN, it immediately shuts down the engine and hydraulic systems. Turn the knob clockwise to allow it to pop back up and turn the power back ON.

A. AIR CONDITIONER ON/OFF SWITCH

This is a 2 position on/off power switch.

B. FAN SPEED - OFF/LOW/MED/HIGH

10. KEY SWITCH, ENGINE START This is a 3-position switch with STOP/RUN/ START positions.

This is a rotary, four position switch for the fan speed.

C. TEMPERATURE - VARIABLE This is a variable, rotary dial to adjust the air temperature of the cab by controlling the flow of engine coolant through the heater core. Make sure this control is set to the MAX COLD position when using the air conditioning. See NOTE below.

STOP Position – All electrical power through the Key switch is turned OFF. Electrical power is still available for the horn, auxiliary power, 2-way radio, cab dome light, work lights and service lights.

NOTE: To maximize the efficiency of the air conditioning, the temperature control must be rotated to the MAX COLD position and the hot water shut off valve on the engine should be turned to the OFF position. Also refer to HOT WATER SHUT OFF VALVE, in THIS SECTION.

RUN Position – Battery is connected to all functions. Used for normal machine operation.

START Position – Connects the battery to the start relay to start the engine. Turning the key to this position starts the engine. The key will return to RUN position when released.

2.17

Controls and Operation

Tigercat T234B Track Loader SHUT-OFF

15 VALVE HOSE TO A/C HEATER UNIT

17

234E-274

HOT WATER SHUT OFF VALVE

15. HOT WATER SHUT OFF VALVE (ENGINE)

234-094

17. VENTILATION

To maximize the efficiency of the air conditioning, the heat control knob (item C on previous page) on the A/C Heater control panel must be rotated to the OFF position.

During times when cab heating is not required, the Hot Water Shut Off Valve (on the heater hose from the engine) should also be closed to prevent hot water from seeping through the A/C unit, thereby reducing the effect of the cooling.

RECIRCULATION AIR FILTER

234-093

The Heating and A/C unit has 10 ventilation outlets. Six are shown here, one is located under the seat and three at the bottom of the front window.

CHECK FIRE EXTINGUISHER

OUTSIDE AIR FILTER

A/C HEATER FILTERS

16. FILTERS Two filters are provided with the heating and A/C unit. One is for filtering recirculated air from the cab. This is located at the bottom of the heater unit and should be inspected and cleaned on a regular basis. The second is for filtering outside air being drawn into the heater unit. This is located adjacent to the heater unit and can be inspected by removing a wingnut below the filter housing so that the filter securing plate can be removed. This filter must be inspected and cleaned/replaced on a regular basis.

234-095

PORTABLE FIRE EXTINGUISHER

18. FIRE EXTINGUISHER A portable fire extinguisher is located in operator's cab. The extinguisher should be checked daily to ensure that it is charged. The pointer on the charge gauge should point to the green region. If the indicator falls out of this green area, the extinguisher should be serviced immediately.

2.18

Tigercat T234B Track Loader 19

20

21

Controls and Operation

22 RESERVOIR

234B-011

19. TWO-WAY RADIO Refer to component manufacturers manual.

20. DOME LIGHT The dome light is turned ON or OFF by the switch in the left armrest control panel.

234B-352

25. WINDSHIELD WASHER FLUID

21. AM/FM STEREO RADIO/CD

In cold climates, fill with an anti-freeze washer fluid. To avoid scratching the windshield, NEVER operate wipers on a dry windshield.

The reservoir is located in the DEF tank compartment on the left-hand front corner of the machine.

Consult the manufacturer's manual for operation instructions.

22. WINDSHIELD WIPER/WASHER The wiper/washer rotary switch controls the windshield wiper. Turning the dial one setting clockwise, operates wiper on intermittent speed which is adjustable.

Turning the dial a setting further clockwise sets the wiper to low speed. Turning the dial a setting further clockwise sets the wiper to high speed. To slow or turn off the wiper, turn the dial counterclockwise until the desired setting is reached.

244-019

To operate the washer function, press and hold the dial. This function sprays washer fluid on the windshield.

24

WINDSHIELD WASHER FLUID

SLIDING WINDOWS HANDLE

25. WINDOWS The right hand window and cab door window are sliding windows. They are opened by pushing on the handle and sliding the window open. To close, slide the window closed firmly allowing the handle to latch on the frame.

23

234B-339

27. DIESEL HEATER CONTROLS - OPTIONAL

23. MANUAL AND DOCUMENT STORAGE

This digital timer is used only if the machine is equipped with the optional diesel heater.

A manual and document storage container is mounted to the inside of the cab door.

Consult the manufacture’s instruction manual for additional information.

24. FIRST AID KIT STORAGE A storage pouch for a first aid kit is located on the inside of the cab door

DIESEL HEATER CONTROL

2.19

Controls and Operation 28. SELECTABLE MACHINE CONTROL (OPTION) T234B-059

ROTARY SWITCH

Tigercat T234B Track Loader If the rotary switch is turned while the pilot is on the pilot will be turned off by the MD3 computer system. An alert warning will be displayed on the MD3 screen.

SELECTABLE MACHINE CONTROL ROTARY SWITCH

T234B-060

Press F2 to confirm the change in switch position and then press the pilot reset button to activate the pilot system.

If equipped with selectable machine control the joysticks and swing foot pedal functions can be switched for operator preference.

Refer to CAB CONTROLS in THIS SECTION for the different joystick configurations.

When switching joystick configurations the pilot should be turned off by lifting the armrest. Turn the selectable machine control rotary switch to the desired position, lower the armrest and press the pilot reset switch to activate the pilot system.

2.20

Tigercat T234B Track Loader CAB TILT

Controls and Operation CAB TILTING PROCEDURE, ELECTRIC PUMP 1. Park machine on level ground.

TILT PUMP KEY SWITCH

2. Lower the grapple onto the ground ensuring grapple and booms are fully supported.

3. Turn OFF the engine.

4. Remove all loose items from the cab.

5. Close cab door.

6. Remove the 4 x 1" locking bolts at the rear of cab riser frame. Doors on the riser frame provide access to the bolts

250D-004

LOCKING BOLTS

CAB TILT PUMP SWITCH

Cab Tilt is operated hydraulically by the cab tilt pump located in the compartment below the cab.

An electric pump and motor and self contained reservoir provide hydraulic power for the cab tilt hydraulic cylinders.

The cab can also be tilted manually with a hydraulic hand pump. See CAB TILTING PROCEDURE, HAND PUMP later in THIS SECTION.

234B-343

REMOVE LOCKING BOLTS

7. Insert key in cab tilt pump key switch on electrical box in engine compartment.

MANUAL OVERRIDE

PUMP RESERVOIR

FILL CAP

234B-111

CAB TILT PUMP

DEXRON III ATF hydraulic oil is used as the hydraulic fluid for the cab tilt hydraulic system.

Remove the fill cap the top of the reservoir to add oil. System capacity is 3.75 L (1 gal US) – reservoir capacity is 0.9 L (30 oz).

8. Ensure that there are no obstacles in front of the cab that would prevent the cab from tilting.

Place a drain pan under the reservoir and operate the cab tilt DOWN and UP with the fill cap off to ensure that the system is not over filled after topping up the reservoir. Wipe up any spilled oil and install the fill cap.

WARNING Ensure that no personnel are in front of the cab before tilting.

2.21

Controls and Operation

Tigercat T234B Track Loader CAB TILTING PROCEDURE, HAND PUMP 1. Park machine on level ground.

2. Lower the grapple onto the ground ensuring grapple and booms are fully supported.

3. Stop the engine.

4. Remove all loose items from the cab.

5. Close cab door.

6. Remove the 4 x 1" locking bolts at the rear of cab riser frame. Doors on the riser frame provide access to the bolts LOCKING BOLTS

234B-343

REMOVE LOCKING BOLTS

7. The cab tilt hand pump handle is stored on the inside of the engine enclosure removable door. Insert the handle into the hand pump located in the engine compartment by the hydraulic pumps.

9. Using the cab tilt pump key switch, turn the key counterclockwise to tilt the cab forward (DOWN) until the tilt cylinder stops.

NOTE: Never leave the cab partially tilted. It should always be either fully forward or fully upright.

10. Using the cab tilt pump key switch, turn the key clockwise to tilt the cab (UP) back to its upright operating position.

11. Reinstall the 4 x 1" locking bolts at the rear of the cab riser frame.

WARNING Failure to install the cab locking bolts will render the machine unsafe.

T234B-017

2.22

CAB TILT HAND PUMP

Tigercat T234B Track Loader

Controls and Operation

8. Ensure that there are no obstacles in front of the cab that would prevent the cab from tilting.

WARNING Ensure that no personnel are in front of the cab before tilting.

HAND PUMP VALVE 9. Ensure the pump valve is turned all the way clockwise. Operate the hand pump to tilt the cab forward (DOWN) until the tilt cylinder stops.

T234B-017

NOTE: Never leave the cab partially tilted. It should always be either fully forward or fully upright.

MANUAL OVERRIDE

CAB TILT PUMP 10. Turn the manual override on the electric pump solenoid valve and operate the hand pump to tilt the cab (UP) back to it's upright operating position.

234B-111

11. Reinstall the 4 x 1" locking bolts at the rear of the cab riser frame.

WARNING Failure to install the cab locking bolts will render the machine unsafe.

12. Turn the manual override on the electric pump solenoid back to the original position.

2.23

Controls and Operation

Tigercat T234B Track Loader

OPERATOR’S SEAT–AIR RIDE

To Lower Firmly lift up on the height adjustment lever. When the lever releases, partially apply operator body weight to the seat until the seat is at the desired height. Firmly push down on the lever. Hold the lever down until the seat locks into position (a click should be heard).

WARNING The seat belt supplied with this seat must be used at all times when operating this machine.

RIDE ADJUSTMENT (B)

C

After adjusting the height, the ride adjustment should be made by pulling or pushing the air ride control valve knob.

H

To Raise

G

Push the ride adjustment control to inflate the air spring to obtain the desired height.

To Lower Pull the ride adjustment control to deflate the air spring to obtain the desired height.

2-WAY ADJUSTABLE LUMBAR (C) For fore-and-aft displacement, rotate horizontal adjustment knob.

D

BACK ANGLE ADJUSTMENT (D)

H

Rotate the back angle adjustment knob to place seat at the desired angle.

G

FORE/AFT SLIDE (E) Move and hold the fore/aft slide lever. Roll the seat forward or backward to the desired position relative to the foot pedal controls.

A B 2I

ARMREST ADJUSTMENT

E

Each armrest has two adjustments to place it in the required position. Loosen the adjustment locking wing bolts to reposition the armrest height and fore/aft position.

F

WIDTH ADJUSTMENT (F)

SEAT ADJUSTMENTS

HEIGHT ADJUSTMENT (A) The spring-assisted height adjustment is controlled by the height adjustment lever located on the front left side of the seat chassis. The four height settings – top, bottom and two in-between, provide a total height adjustment of 75 mm (3 in).

To Raise Firmly lift up on the height adjustment lever. When the lever releases, hold it up while partially lifting the operator’s body weight from the seat. When the seat is at the desired height, firmly push down on the lever until the seat locks (a click should be heard).

Loosen the 2 width adjustment bolts on the underside of the armrest with a 9/16 wrench to adjust the width and angle of the armrest in relation to the seat.

FORE AND AFT ADJUSTMENT (G) Loosen the fore/aft adjustment bolt to allow the armrest to slide forward or back.

UP, DOWN AND ANGLE ADJUSTMENT (H) Loosen the up/down/angle adjustment bolt to allow the armrest to slide up and down or to adjust the angle of the armrest.

2.24

Tigercat T234B Track Loader SEAT HEATER/VENT CONTROLS (I) The seat is equipped with electric heating or venting modes. Two switches located at the front of the seat control these operations.

Controls and Operation PROBLEMS AND CORRECTIVE ACTION

RIDE IS TOO STIFF / SEAT TENDS TO PUSH OR THROW OPERATOR FORWARD The air ride control valve has over pressurized the seat air suspension. This typically happens because the operator is trying to use the air suspension to adjust the ride height rather than using height adjustment lever to raise the seat.

Refer to height adjustment.

RIDES TOO SOFT OR BOTTOMS OUT AND PINCHES OPERATOR 1 234-104

2

HEATER/VENT CONTROLS

The heater/vent switch (1) is a 3 position switch.

The up position turns the seat heater ON and the down position turns the seat vent ON. The middle position is OFF. The low/med/high switch (2) is also a 3 position switch and adjusts the heat level or vent speed depending on the mode selected.

The air ride control valve has under pressurized the seat air suspension ride adjustment.

Insufficient pressure exaggerates the knee-action movement of the seat. This usually happens because the operator is trying to lower the seat by decreasing the amount of air pressure instead of using the height adjustment lever. Refer to height adjustment.

SEAT TOO HIGH/SEAT TOO LOW There are several things which can cause improper seat height. Refer to HEIGHT ADJUSTMENT PROCEDURES and adjust the seat to the desired position. If the proper height cannot be reached using one of the four height adjustment settings, it may be necessary to install the seat on a higher base.

OPERATOR’S LEGS FALLING ASLEEP The seat is adjusted too high, and the air ride control valve has under pressurized the seat air suspension ride adjustment, resulting in the operator sitting in a bucket. Refer to HEIGHT ADJUSTMENT PROCEDURES and RIDE ADJUSTMENT PROCEDURES.

2.25

Controls and Operation ALARM LIGHT

Tigercat T234B Track Loader

MASTER ALARM

234-107 234B-013

COLOUR DISPLAY

MD3 COMPUTER

ARROW (SCROLL) UP OK (ENTER) ARROW (SCROLL) DOWN

234B-087

ESC (BACK) MENU F1 F2 F3 F4 MD3 COMPUTER, ELECTRONIC CONTROL AND DISPLAY

MD3 COMPUTER ELECTRONIC CONTROL & DISPLAY

• Up and down arrow buttons

The MD3 computer, electronic control and display is the operator interface with the electronic control system. The MD3 is the central unit in the control system which works as both a master controller and a display unit. It has a 90 mm (3.5 in) backlit colour graphic transflective display for reading system information.

Navigation buttons that are used to scroll through selections on a menu page. The buttons are configured by program software to bring up a display page, bring up an adjustment group or act as a virtual input.

• OK button .

Pushing this button equals ’enter’. Saves the value or confirms the selection you have made.

The front of the MD3 consists of a control panel with a display and nine buttons. The buttons are arranged on the bottom and right hand side of the display.

• F1 through F4 function buttons,

,

.

• Menu button .

Always brings up the Menu page. It is not programmable.

,

• Esc or BACK button

, .

Programmed buttons that are configured by program software to bring up a display page, bring up an adjustment group or act as an input.

.

Returns you to the previous display page. May be configured by program software to bring up a display page, bring up an adjustment group or act as a virtual input.

2.26

Tigercat T234B Track Loader XC21-A2 EXPANSION MODULE

C4

C3

C2

Controls and Operation

MD3 COMPUTER CONTROL MODULE

C1

ELECTRIC JOYSTICKS

ENGINE DIAGNOSTIC CONNECTOR

XA2-A1 EXPANSION MODULE

ENGINE ELECTRONIC CONTROL UNIT (ECU) ELECTRO-HYDRAULIC CONTROL VALVES

XA2-A0 EXPANSION MODULE

PILOT CONTROL VALVES

G

P3

T3

C

B

A

T234B-062

MD3 COMPUTER ELECTRONIC CONTROL & DISPLAY As an example, the joystick movement/position is transmitted to the XC21-A2 module which sends the signal to the MD3 control module electronically. This message is then transmitted to the XA2-A0 and XA2-A1 expansion modules from the MD3 control and on to the hydraulic control valve solenoid controls. The applicable hydraulic control valves will be activated allowing hydraulic oil to flow to the boom or grapple functions activated by the joystick movement.

The MD3 computer control system is part of a network of components (shown above). The system is made up of the following components: •

MD3 Computer and Display Module

•

Electric Joysticks.

•

XC21-A2 Cab Expansion Module

•

XA2-A0 Expansion Module

•

XA2-A1 Expansion Module

•

Engine Electronic Control Unit (ECU)

•

Hydraulic Control Valve Electronic Solenoids

•

Various controls, switches, sensors and valves not shown.

The engine electronic control module provides electronic information to the MD3 computer via the J1939 CAN BUS link. This information is displayed on the computer display.

The MD3 computer is the main controller in the system. The MD3 computer program is the operating system for the computer display as well as the control system for the machine operating parameters.

2.27

Controls and Operation XC21-A3 CAB MODULE

C4

C3

C2

XC21-A2 CAB MODULE

C4

C1

C3

C2

Tigercat T234B Track Loader MD3 COMPUTER CONTROL MODULE

C1

ELECTRIC JOYSTICKS

ENGINE DIAGNOSTIC CONNECTOR

XA2-A1 EXPANSION MODULE

ENGINE ELECTRONIC CONTROL UNIT (ECU) ELECTRO-HYDRAULIC CONTROL VALVES

XA2-A0 EXPANSION MODULE

PILOT CONTROL VALVES

G

P3

T3

C

B

A

T234B-001

MD3 COMPUTER ELECTRONIC CONTROL & DISPLAY (SELECTABLE MACHINE CONTROL) As an example, the joystick movement/position is transmitted to the XC21 module which sends the signal to the MD3 control module electronically.

This message is then transmitted to the XA2-A0 and XA2-A1 expansion modules from the MD3 control and on to the hydraulic control valve solenoid controls. The applicable hydraulic control valves will be activated allowing hydraulic oil to flow to the boom or grapple functions activated by the joystick movement.

The MD3 computer control system is part of a network of components (shown above). The system is made up of the following components: •

MD3 Computer and Display Module

•

Electric Joysticks.

•

XC21-A2 Cab Expansion Module

•

XC21-A3 Cab Expansion Module

•

XA2-A0 Expansion Module

•

XA2-A1 Expansion Module

•

Engine Electronic Control Unit (ECU)

•

Hydraulic Control Valve Electronic Solenoids

•

Various controls, switches, sensors and valves not shown.

Inputs to the XC21-A3 Cab Module allow the cab controls to be configured for operator preference.

The engine electronic control module provides electronic information to the MD3 computer via the J1939 CAN BUS link. This information is displayed on the computer display.

The MD3 computer is the main controller in the system. The MD3 computer program is the operating system for the computer display as well as the control system for the machine operating parameters.

2.28

Tigercat T234B Track Loader

Controls and Operation

MD3 COMPUTER/ELECTRONIC CONTROL/DISPLAY (CONTINUED) 1

2

3

4

5

16

18

17

6 7 11

10

8

12

13

9

234B-087

14

15

MAIN DISPLAY

MD3 COMPUTER MAIN DISPLAY

16. OPERATOR MODE

1. PILOT RESET ON/OFF

17. COOLING FAN MODE (OPTIONAL)

2. ANTI-STALL ON/OFF

18. TIME

3. MACHINE WARM UP STATUS 4. HYDRAULIC OIL FILTER BYPASS 5. ENGINE AIR INTAKE FILTER RESTRICTION 6. FUEL GAUGE 7. LOW FUEL LEVEL INDICATOR 8. ENGINE TACHOMETER RPM 9. ENGINE COOLANT TEMPERATURE GAUGE 10. HYDRAULIC OIL TEMPERATURE GAUGE 11. DEF LEVEL 12. ENGINE MENU – Press F1 to select 13. ADJUSTMENT MENU – Press F2 to select 14. INFORMATION MENU – Press F3 to select 15. ALARM INDICATORS - Press F4 to select 2.29

Controls and Operation MD3 COMPUTER MODULE

ELECTRIC JOYSTICKS

XC21 EXPANSION MODULE

XA2-A1 EXPANSION MODULE

Tigercat T234B Track Loader

XA2-A0 EXPANSION MODULE

ENGINE ELECTRONIC CONTROL UNIT

HYDRAULIC CONTROL VALVES

9

822C-204

USB PORT - MD3 COMPUTER 234B-002

MD3 COMPUTER SYSTEM COMPONENTS

IMPORTANT! This USB connection should only be used by a trained service technician.

This USB port is used to access the MD3 computer. A laptop with appropriate IQAN software can be plugged into this port for software updates, diagnostics and some adjustments.

Refer to COMPUTER in SECTION 6 of the SERVICE MANUAL for more information and safeguards related to the use of this port.

ENGINE DIAGNOSTICS CONNECTION

234B-012

ENGINE DIAGNOSTICS CONNECTION Plug a remote electronic diagnostic device into this connection such as a lap-top computer with appropriate engine manufacturer’s programming to perform engine performance analysis and tuning.

NOTE: This operation can only be performed by a trained service technician.

2.30

Tigercat T234B Track Loader

Controls and Operation ANTI-STALL

ENGINE MENU

234B-019 234B-017

From the main menu press the F1 button to select the engine display.

Press the F2 button to access the Anti-stall on/off selection. Use the up or down arrow buttons to turn the anti-stall on or off and press OK.

When selected the engine menu icon is on display and the engine functions will also be displayed.

METRIC OR IMPERIAL UNITS

COLD IDLE FUNCTION

Press the F3 button to toggle between metric and imperial units of measure.

COLD IDLE INDICATOR

The engine functions on display are as follows: Charge Air Temperature - °F or °C Engine Coolant Temperature - °F or °C Engine Oil Temperature - °F or °C Fuel Temperature - °F or °C Engine Speed - rpm Turbocharger Boost Pressure - kPa or psi Engine Oil Pressure - kPa or psi

234B-018

Engine Load - % Engine Hours - h

P Press the F1 button to toggle the cold idle function ON/OFF.

Voltage - V Fuel Rate - US gph or L/h (instantaneous) Press the back button to return to the main menu.

2.31

Controls and Operation

Tigercat T234B Track Loader SAW ADJUSTMENT MENU

ADJUSTMENT MENU

Press the F1 button to access the Saw Adjustment menu.

234B-017

234B-025

From the main menu press F2 button to select the ADJUSTMENT MENU.

234B-033

The adjustment menu screen will be displayed.

The adjustment menu icon is on display and all the adjustment selections will also be displayed.

NOTE: The icons and selections displayed are determined by the Machine Configuration set at the factory The 3 adjustment selections are: Saw Adjustments – select F1 Hydraulic oil Grade Adjustments – select F2 Operator Mode Selection – select F3

2.32

Tigercat T234B Track Loader

Controls and Operation

SAW AUTO RETRACT TIME Press F1 button to select the Slasher Saw Auto Retract Time from the SAW ADJUSTMENT MENU.

TOP SAW RETRACT TIME Press F2 button to select the Top Saw Retract Time from the SAW ADJUSTMENT MENU.

234B-022

234B-021

The value can be set between 0 — 5 seconds for the Auto Retract Time. This is the amount of time that the saw retract will stay active after the slasher saw cut button has been released. The time should be adjusted to allow the slasher saw bar to retract fully. If the time is set longer than necessary hydraulic heat will be created in the main valve.

The value can be set between 0 — 5 seconds for the Top Saw Retract Time. This sets the time after the top saw has completed cutting to auto retract.

Use the up or down arrow buttons to adjust the time and press OK.

Use the up or down arrow buttons to adjust the time and press OK. NOTE: To disable auto saw retract, set the retract time to 0 seconds.

2.33

Controls and Operation

Tigercat T234B Track Loader

SAW FLOW ADJUSTMENT Press F3 button to select the Saw Flow Adjustment from the SAW ADJUSTMENT MENU.

234B-029

A new message appears on the display "Enter PIN Code. The factory PIN is '0000'. This number will remain the same until the password (PIN Code) is changed. Press the OK button 4 times to enter '0000'.

234B-026

This function is password protected and requires entering a 4 digit PIN number to make adjustments.

IMPORTANT! Before making any adjustments make sure you are aware of the flow requirements of your particular saw. Over driving the saw motor with more flow than required can damage your saw.

Select F1 (ENTER PIN) to enter PIN.

234B-032

At this point the check mark will be displayed beside the PIN number to show that the correct PIN code has been selected. The flow adjustment icon will also be displayed above the F3 button If you wish to change the password, select F2 SET PWD. Use the arrow up/arrow down and OK buttons to enter the new 4 digit PIN. Remember the new PIN code. It will be required after the computer has been turned off when the ignition key has been put in the stop position. See RESETTING THE PASSWORD on this page if you forget the password.

Press the F3 button to access the Saw Flow Adjustment menu.

RESETTING THE PASSWORD - If you forget the password, press the UP, OK and DOWN buttons simultaneously.

Release the buttons, press the OK button until the 'X' mark appears. Then enter 1234 and press OK. This is the new password.

If you wish to change the password, select F3 SET PWD. Use the arrow up/arrow down and OK buttons to enter the new 4 digit PIN.

2.34

Tigercat T234B Track Loader

Controls and Operation

234B-031

234B-031

The adjustments are used to control hydraulic flow of the Slasher Saw (F1) and Top Saw (F2).

Press F2 to select the Top Saw Flow adjustment.

The adjustments have been factory set. This setting will give a hydraulic flow of 188 L/min (50 gpm) to the slasher saw.

IMPORTANT! Before making any adjustments make sure you are aware of the flow requirements of your particular saw. Over driving the saw motor with more flow than required can damage your saw.

Press F1 to select the Slasher Saw Flow adjustment.

234B-028

Use the arrow up button to increase the value, or use the arrow down button to decrease the value.

When the desired value has been selected press the OK button to set the value and return to the flow adjustment menu.

Note: Once the adjustment has been made check the L/min or gpm reading is within specification of your particular saw.

234B-027(1)

Note: To set metric or imperial measure press F3 to change mode.

Use the arrow up button to increase the value, or use the arrow down button to decrease the value.

When the desired value has been selected press the OK button to set the value and return to the flow adjustment menu.

If no further adjustments are required press the back button to return to the main menu.

Note: Once the adjustment has been made check the L/min or gpm reading is within specification of your particular saw.

Note: To set metric or imperial measure press F3 to change mode.

2.35

Controls and Operation OIL GRADE SELECTION Press F2 button to select OIL GRADE Menu from the ADJUSTMENT MENU.

Tigercat T234B Track Loader OPERATOR MODE SELECTION Press F3 button to select the Operator Mode Menu from the ADJUSTMENT MENU.

234B-063

234B-062

The oil grade menu will appear. Multiple oil grade choices are given. Use the up or down arrow buttons to scroll to the desired oil grade and press OK when complete.

The Operator Mode Menu will appear. There are four choices to choose from: •

M0 = Training Mode

•

M1 = Operator Mode 1

•

M2 = Operator Mode 2

•

M3 = Operator Mode 3

The machine is factory set at M2. Select M1 for smoother operation and M3 for more aggressive operation. Use the up or down arrow buttons to scroll to the desired selection and press OK.

2.36

Tigercat T234B Track Loader

Controls and Operation

INFORMATION MODE SELECTION

Press the F1 button to select the joystick feedback screen.

234B-017 234B-034

Press the F3 button to access the information menu.

This screen provides feedback from the joystick buttons and axis for diagnostic purposes.

234B-035

The information menu displays the following information:

Serial Number

Machine Hours - h Hydraulic Oil Temp -°F or °C Hydraulic Oil Pressure, Load Sense Total fuel information Trip fuel information Press the F2 button to reset the trip average fuel rate and trip fuel used functions.

Press the F3 button to toggle between imperial and metric units of measure.

2.37

Controls and Operation

Tigercat T234B Track Loader

MAIN MENU PAGE

234B-017

Press the menu button menu page.

to go to the main

234E-053

The main menu page displays the following selections: •

Adjust – Select F1

•

Measure – Select F2

•

Preferences – Select F3

•

Info – Select F4

To return to the Main menu press the button

.

2.38

Tigercat T234B Track Loader ADJUST MENU

Controls and Operation OPERATOR MODE See Operator Mode earlier in THIS SECTION MACHINE PARAMETERS From the Adjust Menu use the up or down arrow buttons to scroll to Machine Parameters and press OK.

234E-053

From the main menu page press the F1 button (Adjust) to access the adjust menu.

T234B-234

In the machine parameters menu the following items can be selected:

234B-101

This menu is an alternate method of accessing the adjustment menu to make machine adjustments. See ADJUSTMENT MENU earlier in this section for details.

The Main menu appears and the following menu items can be selected.

•

Anti-Stall

•

Oil Grade

•

Idle Down Wait Time

•

Hoist Boom Cushion Status

•

Stick Boom Cushion Status

•

Grapple Open/Close Fine Control

•

Grapple Saw Status

Use the up or down arrows buttons to scroll to the desired selection and press the OK button to set the selection.

ANTI-STALL See Anti-Stall earlier in THIS SECTION.

•

Operator Mode

OIL GRADE

•

Machine Parameters

See Oil Grade earlier in THIS SECTION

•

*Attachment Settings

•

Auto Retract Settings

•

Engine

•

Fan

*NOTE: Attachment Flow Settings will only appear on this menu when the PIN code has been entered to permit access to this adjustment. For details on entering PIN code see SAW FLOW ADJUSTMENT earlier in THIS SECTION. 2.39

Controls and Operation

Tigercat T234B Track Loader

IDLE DOWN WAIT TIME

HOIST BOOM CUSHION STATUS

Use the up or down arrow buttons to scroll to the Idle Down Wait Time selection and press the OK button to set the selection.

234B-236

Use the up or down arrow buttons to scroll to the Hoist Boom Cushion Status selection and press the OK button to set the selection.

234B-041

In the Idle Down Wait Time menu the value can be adjusted from 10 – 60 seconds using the arrow up/down buttons to change the value, then press the OK button to set the new value. The factory default value is 10 seconds. This function is an automatic idle down feature.

AUTO IDLE DOWN – If the engine is set to run at full throttle and no functions are activated for a 10 seconds, the engine will idle down automatically. The engine will return to the set idle speed as soon as a function is activated.

NOTE: During cold weather the computer limits maximum idle speed until the hydraulic oil has reached a specific temperature based on the oil grade selected. See COLD WEATHER STARTING on page IN THIS SECTION.

234B-070

Use the up or down arrow buttons to turn the Hoist Boom Cushion Status On or Off and press the OK button to set the selection.

When the Hoist Boom Cushion Status is on the cylinders will automatically slow down before they reach the end of stroke.

Press the back button to return to the Machine Parameters menu.

2.40

Tigercat T234B Track Loader

Controls and Operation

STICK BOOM CUSHION STATUS

GRAPPLE OPEN/CLOSE FINE CONTROL

234B-237

234B-235

Use the up or down arrow buttons to scroll to the Stick Boom Cushion Status selection and press the OK button to set the selection.

Use the up or down arrow buttons to scroll to the Grapple Open/Close Fine Control selection and press the OK button to set the selection.

234B-071

Use the up or down arrow buttons to turn the Stick Boom Cushion Status On or Off and press the OK button to set the selection.

When the Stick Boom Cushion Status is on the cylinders will automatically slow down before they reach the end of stroke.

234B-233

Use the up or down arrow buttons to adjust this setting to suit. Increasing this value will provide more fine control of the grapple open/close movement when using the joysticks. Click on OK once the adjustment has been made.

2.41

Controls and Operation

Tigercat T234B Track Loader

GRAPPLE SAW STATUS

T234B-025

Use the up or down arrow buttons to scroll to the Grapple Saw Status selection and press the OK button to set the selection.

T234B-023

Use the up or down arrow buttons to turn this setting ON of OFF. This setting should only be ON when a grapple saw is present. Click on OK once the selection has been made.

2.42

Tigercat T234B Track Loader ATTACHMENT SETTINGS

Controls and Operation DELIMBER STATUS

234B-058

234B-094

From the Adjust Menu use the up or down arrow buttons to scroll to the Attachment Settings selection and press the OK button to set the selection.

TOP SAW FLOW % Because any adjustment to the Top Saw Flow % requires the flow rate to be checked this adjustment should only be done using the SAW FLOW ADJUSTMENT procedure described earlier in THIS SECTION. IMPORTANT! Before making any adjustments make sure you are aware of the flow requirements of your particular saw. Over driving the saw motor with more flow than required can damage your saw.

SLASHER FEED FLOW % Because any adjustment to the Slasher Feed Flow % requires the flow rate to be checked this adjustment should only be done using the SAW FLOW ADJUSTMENT procedure described earlier in THIS SECTION. NOTE: The Slasher Feed Flow % may relate to either a Slasher Saw Flow or a Circle Saw Feed Flow.

IMPORTANT! Before making any adjustments make sure you are aware of the flow requirements of your particular saw. Over driving the saw motor with more flow than required can damage your saw.

From the Adjust Menu use the up or down arrow buttons to scroll to the Delimber Status and press OK.

234B-053

Use the up or down arrow buttons to select the Delimber Status and press OK.

2.43

Controls and Operation

Tigercat T234B Track Loader

AUTO RETRACT SETTINGS

AUTO SLASHER SAW RETRACT TIME

234B-038

234B-093

In the Auto Slasher Saw Retract Time selection the value can be adjusted from 0 – 5 seconds.

This sets the time after the slasher saw has completed cutting to auto retract.

To reset the value use the up or down arrow buttons to change the value then press the OK button to set the value.

Use the arrow up or down arrow buttons to scroll to the Auto Retract Settings selection and press the OK button to set the selection.

234B-045

Use the up or down arrow buttons to scroll to Auto Slasher Saw Retract Time and press OK.

234B-044

Use the up or down arrow buttons to scroll to Top Saw Ret Time and press the OK button to select the menu item.

2.44

Tigercat T234B Track Loader TOP SAW AUTO RETRACT TIME

Controls and Operation GRAPPLE SAW AUTO RETRACT TIME

234B-042

In the Top Saw Retract Time selection the value can be adjusted from 0 seconds to 5 seconds.

This sets the time after the saw has completed cutting to auto retract.

To reset the value use the up or down arrow buttons to change the value then press the OK button to set the value.

234B-040

In the Grapple Saw Retract Time selection the value can be adjusted from 0 – 5 seconds. This sets the time after the saw has completed cutting to auto retract.

To reset the value use the up or down arrow buttons to change the value then press the OK button to set the value.

234B-036

Use the up or down arrow buttons to scroll to the Grapple Saw Ret Time and press the OK button to select the menu item.

2.45

Controls and Operation ENGINE

Tigercat T234B Track Loader COLD IDLE SPEED

234B-047 234B-097

From the Adjust Menu use the up or down arrow buttons to scroll to the Engine selection and press the OK button to set the selection.

The Cold Idle Speed can be adjusted from 1000 – 1400 rpm.

To adjust the value use the up or down arrow buttons to change the setting and press the OK button to set the value.

234B-095

Using the up or down arrow buttons scroll to Cold Idle Speed and press OK

234B-100

Using the up or down arrow buttons scroll to Max Engine Speed and press OK

2.46

Tigercat T234B Track Loader

Controls and Operation IDLE ENGINE SPEED

MAX ENGINE SPEED

234B-092

234B-050

The Max Engine Speed can be adjusted from 1600 – 2200 rpm.

To adjust the value use the up or down arrow buttons to change the setting and press the OK button to set the value.

The Idle Speed can be adjusted from 1000 – 1250 rpm.

To adjust the value use the up or down arrow buttons to change the setting and press the OK button to set the value.

234B-103

Using the up or down arrow buttons scroll to Idle Engine Speed and press OK.

2.47

Controls and Operation FAN

Tigercat T234B Track Loader ENABLE AUTO CLEAN

234B-091

234B-102

From the Adjust Menu use the up or down arrow buttons to scroll to the Fan selection and press the OK button to set the selection.

This selection enables or disables the Auto Clean function of the fan. If ON is selected the fan will automatically complete a clean cycle as per the Clean Frequency and Clean Duration settings.

Use the up or down arrow buttons to scroll to the desired selection and press OK.

234B-098

Using the up or down arrow buttons scroll to Fan Auto Clean and press OK.

234B-099

Using the up or down arrow buttons scroll to Clean Frequency and press OK.

2.48

Tigercat T234B Track Loader AUTO CLEAN FREQUENCY

Controls and Operation AUTO CLEAN DURATION

234B-089

If the Auto Clean function is enabled this setting adjusts the frequency of the clean cycle. The frequency can be adjusted from 1 minute to 420 minutes. The factory default setting is 30 minutes.

Use the up or down arrow buttons to adjust the setting and press OK.

234B-088

This setting determines how long the clean cycle will run for. The clean cycle can be adjusted from 5 seconds to 20 seconds. The factory default setting is 15 seconds.

Use the up or down arrow buttons to adjust the setting and press OK.

234B-096

Using the up or down arrow buttons scroll to Clean Duration and press OK.

2.49

Controls and Operation

Tigercat T234B Track Loader

MEASURE MENU

From the main menu page press the F2 button (Measure) to access the measure menu.

234B-083

The following menu items can be selected.

•

Engine Parameters

•

IQAN Status

•

LH Joystick

•

RH Joystick

•

Valve Functions

•

Inputs

•

Outputs

Use the Arrow Up or Arrow Down to select the menu item. Press OK to confirm the selection.

This menu is used by Tigercat service technicians.

Refer to SECTION 6 of the SERVICE MANUAL for more information. Press the back button (or F1) to return to the main menu page.

2.50

Tigercat T234B Track Loader

Controls and Operation

PREFERENCES MENU

DISPLAY ADJUSTMENT

From the main menu page press the F3 button (Preferences) and the preferences menu page appears.

After selecting F1 the display adjustment screen opens and the following adjustments can be selected: RETURN TO MAIN MENU – Select F1 BACKLIGHT ADJUSTMENT – Select F2 SCREEN SAVER – Select F3

234B-074

The following menu items can be selected.

•

Display

•

Date/Time

•

Language

BACKLIGHT ADJUSTMENT After selecting F2 the backlight adjustment screen opens. Use the Arrow Up or Arrow Down buttons to adjust the display backlight. The range is 10 to 100. The default setting is 100.

When the desired setting is selected press the OK button. A good rule to follow is the lower the number ,the longer the life of the display unit.

2.51

Controls and Operation

Tigercat T234B Track Loader

SCREEN SAVER ADJUSTMENT

DATE/TIME ADJUSTMENT

234B-074

Select F3 to open the screen saver adjustment screen. Use the Arrow Up and Arrow Down buttons to scroll through the choices. Three choices are available: •

SCREEN SAVER OFF

•

DIMMED – Timeout 5 seconds

•

BLACK – Timeout 5 seconds

Press F2 to select the DATE/TIME adjustments in the PREFERENCES menu.

234B-075

The DATE/TIME menu screen turns on. Two choices are available for adjustment: DATE – select F1 TIME – select F2 After making a selection press the OK button to confirm selection and press the back button return to the main menu screen.

to

2.52

Tigercat T234B Track Loader

Controls and Operation

DATE ADJUSTMENT

When the month has been confirmed the display will highlight the DAY. Use the Arrow Up or Arrow Down to select the day. Press OK to confirm day selected.

Press F1 to select DATE. Use the Arrow Up or Arrow Down to scroll through the YEAR list to select the year. Press OK to confirm year selected.

234B-075

The display will return to the DATE TIME menu.

When the year has been confirmed the display will highlight the MONTH. Use the Arrow Up or Arrow Down to select the month. Press OK to confirm month selected.

2.53

Controls and Operation

Tigercat T234B Track Loader INFO MENU PAGE

TIME ADJUSTMENT Select F2 Time adjustment from the DATE/TIME display screen.

From the main menu page press the F4 button The Time display screen will turn on. Use the Arrow Up or Arrow Down to select the HOUR. Press the OK button to confirm selection. The display will show the MINUTES highlighted.

(Info) and the Info menu page appears.

The following menu items can be selected.

Use the Arrow Up or Arrow Down to select the minute. Press OK button to confirm the selection.

The display will return to the DATE/TIME menu screen. Press the back button main menu screen.

•

Modules – Select F1

•

Logs – Select F3

The machine ID information will be displayed on the screen.

to return to the

2.54

Tigercat T234B Track Loader

Controls and Operation

MODULES

LOGS

T234B-062

Press F1 to select the modules menu. This menu provides information on the following machine modules: •

MD3 Computer Module

•

XA2-A0 Expansion Module (Valve Side)

•

Tigercat FPT NEF Engine ECU

•

XC21-A2 Cab Module

•

XA2-A1 Expansion Module (Engine Side)

•

XC21-A3 Cab Module (If Equipped)

Press F3 from the Info menu page to select logs.

This menu lists System Logs and Alarm Logs and the number of records within each log. The records are a list of all the fault occurrences in each log.

Use the Arrow Up or Arrow Down to select the menu item. Press OK to confirm the selection.

This menu is used by Tigercat service technicians.

Refer to SECTION 6 of the SERVICE MANUAL for more information.

Press the back button to return to the Info screen or F1 to return to the main menu page.

234B-076

Shown above the MD3 module has been selected. Specific information for the MD3 is displayed on the screen.

This menu is used by Tigercat service technicians.

Refer to SECTION 6 of the SERVICE MANUAL for more information.

Press the back button to return to the Info screen or F1 to return to the main menu page.

2.55

Controls and Operation

Tigercat T234B Track Loader

MD3 MESSAGES ALARM LIGHT

MASTER ALARM

234-107

The MD3 Controller displays messages and activates the master alarm and alarm light whenever a system fault occurs. Note that the computer control system will automatically perform a bulb test at engine start up to ensure that master alarm and alarm light are functioning.

Refer to STARTING ENGINE in THIS SECTION. There are different types of Messages and Alarms, they appear on the screen as a block message.

The types of messages are: •

CRITICAL MESSAGE – Color RED

•

ERROR MESSAGE – Color RED

•

ALERT MESSAGE – Color YELLOW

•

INFORMATION MESSAGE – Color BLUE

Messages can be hidden or acknowledged by pressing the F2 button (Hide or OK).

All messages that have been hidden or acknowledged are stored in the computer.

In some instances it will be necessary to immediately stop the machine, shut the engine OFF and repair the problem causing the message.

234B-079

Active fault messages that have been hidden can be reviewed by pressing the F4 button. Recalled messages will be displayed in order starting with the highest priority first.

2.56

Tigercat T234B Track Loader

Controls and Operation

CRITICAL MESSAGES (RED) Critical messages advise the operator that a critical machine fault is about to occur or a system fault has occurred.

Critical messages have the highest level of priority and are used to alert operator that immediate action must be taken to prevent damage to machine or to ensure operator safety.

Critical messages flash the critical symbol above the F4 button when active messages are hidden. The symbol will continue to flash until the problem is resolved and the fault becomes inactive.

When a critical message is displayed, the master alarm and alarm light will sound and flash continuously. The message remains on the screen until the operator hides it.

Active messages that have been hidden can be reviewed by pressing the F4 button.

A list of some CRITICAL MESSAGES is as follows:

234B-078

•

Engine Air Filter.

•

Hydraulic Oil Level Low.

•

Hydraulic Oil Temperature High

•

Engine Coolant Temperature High

•

Engine Oil Temperature High

•

Engine Coolant Level Low

•

Engine Oil Pressure Low

However, if the machine cannot be stopped immediately for safety reasons, the operator can hide the message. In this instance the machine should only be operated long enough to make the machine safe, then STOP machine operation and SHUT THE ENGINE OFF before serious machine damage can occur!

•

Engine Fault Code Messages - Critical

•

Hardware Fault – MD3

•

Hardware Fault – Engine

•

Hardware Fault – XA2

•

Hardware Fault – XS2

Messages can be hidden by pressing the F2 button (Hide).

•

Hardware Fault - Denox module

•

Engine Restarts Remaining Until Engine Lockout

•

Engine Locked Out

•

Aftertreatment System Engine Idle Too Long

•

Aftertreatment System Messages

•

Diesel Exhaust Fluid Quality

The message will give brief details of the fault and advise what action is necessary.

In some instances the machine requires immediate action to correct the problem which requires the operator to STOP machine operation, SHUT THE ENGINE OFF and service the machine to correct the problem.

NOTE: Not all messages are shown.

2.57

Controls and Operation

Tigercat T234B Track Loader

CRITICAL MESSAGES

HYDRAULIC OIL TEMPERATURE HIGH

ENGINE AIR FILTER RESTRICTION

Hydraulic Oil

Engine Air Filter

Temperature High.

Restricted. Service machine

This message will be displayed, alarm light will flash and alarm will sound when the oil temperature exceeds the recommended operating range for the type of hydraulic oil in use.

This message will be displayed, alarm light will flash and alarm will sound when the engine air filter has reached maximum restriction.

If the temperature rises above the recommended operating range for the type of hydraulic oil in use check the following:

To prevent damage to the engine, stop the engine immediately and replace the air filters.

NOTE: Replace the safety element every third primary filter change.

•

Plugged oil cooler

•

Malfunction in a hydraulic system

•

High loads on the hydraulic system

•

Malfunction of the cooling fan

Hydraulic Oil

•

Low hydraulic oil level

Level Low.

•

Correct Hydraulic Oil Grade Selection

HYDRAULIC OIL LEVEL LOW

If hydraulic oil temperature rises above the recommended operating range DO NOT continue to operate the machine.

This message will be displayed, alarm light will flash and alarm will sound when the main hydraulic tank oil level is low.

This alarm must not be used to monitor the hydraulic oil. The operator must use the hydraulic oil temperature gauge on the main menu, together with the operating range chart in SECTION 3 to prevent damage to the hydraulic system.

Stop the engine immediately when this alarm is activated. Operating machine with a low hydraulic oil level can cause hydraulic pumps to fail.

Hydraulic oil grade information is shown on the main menu below the hydraulic oil temperature gauge.

When this alarm is activated stop the engine and look for signs of broken hoses or other leaks.

Repair leaks and refill the main hydraulic tank to FULL mark on the sight gauge. Restart engine and inspect for leaks.

Operating outside the recommended operating range will shorten hydraulic component life.

Refer to COMPUTER – ADJUSTMENT MENU SERVICE SETTINGS – HYDRAULIC OIL GRADE in THIS SECTION for hydraulic oil grade selection settings information.

Refer also to APPROVED HYDRAULIC OILS in SECTION 3 for hydraulic oil operating range information.

Refer to COMPUTER – INFORMATION MODE MENU – HYDRAULIC OIL TEMPERATURE in THIS SECTION for hydraulic oil temperature information display.

2.58

Tigercat T234B Track Loader

Controls and Operation

ENGINE OIL PRESSURE LOW

ENGINE FAULT CODE MESSAGES - CRITICAL

SPN: 9939 1 of 1

SPN: ##### 1 of 1

Engine Oil Pressure Low.

Contact dealer.

This message will be displayed, alarm warning light will flash and alarm will sound when engine oil pressure falls below 0.7 bar (10 psi ).

Turn OFF the engine when this alarm is activated.

Check engine oil levels.

Refer to STARTING THE ENGINE in THIS SECTION for more information.

ENGINE OIL TEMPERATURE HIGH

SPN: 7123 1 of 1 Engine oil temperature high.

This message will be displayed, alarm warning light will flash and alarm will sound when engine oil temperature exceeds recommended engine temperature.

Check the cooling system and fan for proper operation and run a clean cycle. It is also important to manually clean debris from the machine on a regular basis to maintain low machine operating temperatures. Refer to CLEANING A/C CONDENSER AND COOLING SYSTEM in THIS SECTION.

Critical engine fault message(s) will be displayed, alarm warning light will flash and alarm will sound when a critical engine fault message is received from the engine electronic control unit.

They provide the SPN code (suspect parameter number) as well as a message describing the fault (when available).

Critical engine fault codes are higher priority messages than alert level engine fault code messages. Critical messages can be hidden but immediate action must be taken, STOP machine operation and service engine immediately to resolve the cause of the fault.

Note that some less common engine fault codes will appear without a message describing the fault.

Make a note of the SPN code and contact service for more information.

Refer to engine OPERATION AND MAINTENANCE MANUAL for specific information regarding the engine and aftertreatment system.

NOTE: Contact your Tigercat dealer to obtain an Engine Fault Codes chart. An up to date copy should be kept in the manual box (in the cab). The chart is updated regularly by the engine manufacturer, so it is important to check periodically with the Tigercat dealer to ensure that you have a current copy of the Engine Fault Codes chart.

Refer to engine OPERATION AND MAINTENANCE MANUAL for service information.

2.59

Controls and Operation

Tigercat T234B Track Loader HARDWARE FAULT - MD3

ENGINE COOLANT TEMPERATURE HIGH

SPN: 63011 1 of 1

Hardware Fault - MD3

Engine coolant temperature high.

Active fault has been hidden. Turn key off and on to recall active hidden hardware faults.

This message will be displayed, alarm warning light will flash and alarm will sound when engine coolant temperature exceeds recommended engine temperature.

This message will be displayed, alarm light will flash and alarm will sound when a critical active hardware fault related to the MD3 Display module has been hidden.

Check the cooling system and fan for proper operation and run a clean cycle. It is also important to manually clean debris from the machine on a regular basis to maintain low machine operating temperatures. Refer to CLEANING A/C CONDENSER AND COOLING SYSTEM in THIS SECTION.

To recall the original active fault(s) the operator must turn the key off and on.

A VREF error is an example of the type of hardware fault which will be the original active fault which triggers this message.

HARDWARE FAULT - XC21-A2

Refer to engine OPERATION AND MAINTENANCE MANUAL for service information.

Hardware Fault - XC21-A2

ENGINE STOP

Active fault has been hidden. Turn key off and on to recall active hidden hardware faults.

Engine Stop Critical engine fault active - contact service.

This message will be displayed, alarm light will flash and alarm will sound when a critical active hardware fault related to the XC21-A2 cab module has been hidden.

This message will be displayed, alarm light will flash and alarm will sound when the engine stops while the ignition switch is in the RUN position and/or when critical engine alarms are triggered.

To recall the original active fault(s) the operator must turn the key off and on.

A VREF and no contact errors are examples of the type of hardware fault which may be the original active fault which triggers this message.

Refer to engine manufacturer's manual for specific information regarding the engine.

2.60

Tigercat T234B Track Loader

Controls and Operation

HARDWARE FAULT - XC21-A3

HARDWARE FAULT - XA2-A1

Hardware Fault - XC21-A3

Hardware Fault - XA2-A1

Active fault has been hidden. Turn key off and on to recall active hidden hardware faults.

Active fault has been hidden. Turn key off and on to recall active hidden hardware faults.

This message will be displayed, alarm light will flash and alarm will sound when a critical active hardware fault related to the XC21-A3 cab module has been hidden.

This message will be displayed, alarm light will flash and alarm will sound when a critical active hardware fault related to the XA2-A1 module has been hidden.

To recall the original active fault(s) the operator must turn the key off and on.

To recall the original active fault(s) the operator must turn the key off and on.

A VREF and no contact errors are examples of the type of hardware fault which may be the original active fault which triggers this message.

A VREF and no contact errors are examples of the type of hardware fault which may be the original active fault which triggers this message.

HARDWARE FAULT - XA2-A0

HARDWARE FAULT - ENGINE

Hardware Fault - Engine Hardware Fault - XA2-A0

Active fault has been hidden. Turn key off and on to recall active hidden hardware faults.

Active fault has been hidden. Turn key off and on to recall active hidden hardware faults.

This message will be displayed, alarm light will flash and alarm will sound when a critical active hardware fault related to the XA2-A0 module has been hidden.

This message will be displayed, alarm light will flash and alarm will sound when a critical active hardware fault related to the Engine has been hidden.

To recall the original active fault(s) the operator must turn the key off and on.

To recall the original active fault(s) the operator must turn the key off and on.

A VREF and no contact errors are examples of the type of hardware fault which may be the original active fault which triggers this message.

No contact error is an example of the type of hardware fault which may be the original active fault which triggers this message.

2.61

Controls and Operation

Tigercat T234B Track Loader

AFTERTREATMENT SYSTEM TECHNICAL FAILURE

AFTERTREATMENT SYSTEM ENGINE IDLE TOO LONG

Aftertreatment System

Aftertreatment System

Technical failure severe. Engine lockout will occur after full torque derate and 3 engine restarts.

Engine idle too long. Shutdown engine to prevent damage to emission control system.

This message will be displayed, alarm light will flash and alarm will sound when an aftertreatment technical fault is detected. Action to correct the problem should be taken immediately to avoid affecting engine performance and damage to the SCR aftertreatment system components.

This message will be displayed, alarm light will flash and alarm will sound when this engine has idled for more than 4 consecutive hours.

Shutdown engine to prevent damage to the emission control system.

IMPORTANT! Engine should not idle longer than 4 consecutive hours. Damage to the emission control system will result. When this machine idles for an extended period excess hydrocarbon buildup is created in the SCR aftertreatment system. Burn off of excess hydrocarbon at full load immediately after a long idle period will generate excess heat which will cause damage to emission control system components. It will take 45 minutes at 40% load (or an SCR exhaust outlet temperature of 320°C (608°F) to burn off the hydrocarbon that accumulates during a 4 hour long idle.

This message results in the following derate and shutdown sequence if no action is taken to correct the problem: •

Beginning immediately after an aftertreatment system technical message there will be a ramp down of Torque by 25% over 25 minutes.

•

After 1 hour at reduced torque there will be a ramp down of Engine Speed by 60% and Torque by 65% over 40 minutes.

•

After 2 hours at derated engine speed and torque the engine is derated to idle within 30 minutes.

•

A total of 3 restarts are allowed after any derate has started.

Refer to COMPUTER–MESSAGES - CRITICAL – ENGINE LOCKED OUT and ENGINE RESTARTS REMAINING UNTIL ENGINE LOCKOUT in THIS SECTION. Identify the cause of the technical failure and take action to correct the problem.

Refer also to AFTERTREATMENT SYSTEM in SECTION 3 for more information.

2.62

Tigercat T234B Track Loader

Controls and Operation

DIESEL EXHAUST FLUID QUALITY

WARNING Use only diesel exhaust fluid (DEF) which meets ISO 22241 specifications. NEVER fill the DEF tank with any other fluid.

DEF is injected into the exhaust gas stream during normal operation of the Selective Catalytic Reduction (SCR) aftertreatment system.

Use of other fluids may cause component damage, or a fire risk which could result in death or serious injury.

Diesel Exhaust Fluid Quality warning severe. Engine lockout will occur after full torque derate and 3 engine restarts.

This message will be displayed, alarm light will flash and alarm will sound when a diesel fluid quality problem is detected. Action to correct the problem should be taken immediately to avoid affecting engine performance and damage to the Selective Catalytic Reduction (SCR) aftertreatment system components.

This message results in the following derate and engine lockout sequence if no action is taken to correct the problem: •

Beginning 1 hour after a Diesel Exhaust Fluid (DEF) quality message, there will be a ramp down of Engine Speed by 60% and Torque by 65% over 40 minutes.

•

After 2 hours at derated engine speed and torque the engine is derated to idle within 30 minutes.

•

A total of 3 restarts are allowed after any derate has started. Refer to COMPUTER – MESSAGES – CRITICAL–ENGINE LOCKED OUT and ENGINE RESTARTS REMAINING UNTIL ENGINE LOCKOUT in THIS SECTION.

To correct the DEF quality problem, clean the area around the DEF tank then drain and refill the tank with clean DEF which meets ISO 22241 specifications. Additional messages from the Denox Module will also be displayed. Refer to Engine Manuals for code information.

Note that an Engine Torque Derate Active message will also be triggered as the engine begins to derate. Refer to COMPUTER – MESSAGES – ALERT – ENGINE TORQUE DERATE ACTIVE. Refer to DIESEL EXHAUST FLUID TANK in THIS SECTION and DRAINING DIESEL EXHAUST FLUID TANK in SECTION 3.

Refer also to AFTERTREATMENT SYSTEM in SECTION 3 for more information regarding the use of DEF and its function in the SCR aftertreatment system.

2.63

Controls and Operation

Tigercat T234B Track Loader

ERROR MESSAGES (RED) Error messages advise the operator that a critical machine fault is about to occur or a system fault has occurred.

Error messages are computer system generated and are generally triggered by computer system error and fault related conditions.

Error messages have the second highest level of priority and are used to alert the operator that immediate action must be taken to prevent damage to machine or to ensure operator safety.

A list of some types of ERROR MESSAGES is as follows:

Error messages are activated whenever a fault such as an electrical connection is broken/ disconnected. Most error messages are due to computer system hardware or connection faults.

Module VREF Error Voltage Input Error (VIN)

When an error message is displayed, the master alarm and alarm light will sound and flash continuously. The message remains on the screen until the operator hides it.

The message will give brief details of the fault and advise what action is necessary.

In some instances the machine requires immediate action to correct the problem which requires the operator to stop machine operation, shut the engine off and service the machine to correct the problem.

However, if the machine cannot be stopped immediately for safety reasons, the operator can hide the message. In this instance the machine should only be operated long enough to move the machine to a safe location then stop machine operation and shut the engine off before serious machine damage can occur!

Messages are acknowledged by pressing the F2 button (OK). To recall active messages turn key off and on. On screen messages will indicate to the operator that an active hardware fault has been hidden.

Error messages flash the Critical symbol

or

the Alert above the F4 button when active messages are hidden depending on the type of error message. The symbol will continue to flash until the problem is resolved and the fault becomes inactive.

Active messages that have been hidden can be reviewed by pressing the F4 button.

2.64

Digital Input Error (DIN) Digital Output Error (DOUT) Current Output Error (COUT) Module No Contact Error * Note that not all error messages are shown.

Tigercat T234B Track Loader

Controls and Operation

MODULE VREF ERROR

XC21-A2

MD3

VREF error Value 0.29 V

VREF error Value 0.29 V

XC21-A3 VREF error Value 0.29 V

XA2-A0 VREF error Value 0.29 V The module VREF message will be displayed to indicate a problem related to the 5 V reference signal coming from the module.

The module is identified on the display screen.

This message indicates a problem with a sensor, connecting wires or the 5V reference signal itself.

Once acknowledged this message will be replaced with a hardware fault message for the corresponding module when active faults are recalled to the screen. Refer to COMPUTER ~ MESSAGES - CRITICAL ~ HARDWARE FAULT in THIS SECTION.

XA2-A1 VREF error Value 0.29 V

2.65

Controls and Operation

Tigercat T234B Track Loader

MODULE NO CONTACT ERROR

Valve Side XA2-A0

Engine Side XA2-A1

No contact

No contact

Cab Input Module XC21-A2 No contact

Cab Input Module XC21-A3 No contact The module no contact error message will be displayed to indicate a loss of communication with or power to a module. The module is identified on the display screen.

When a module loses contact all machine functions controlled by that module cease and all messages and warnings associated with that module are triggered. If the problem is with the CAN wires all modules beyond the problem module will also be affected.

Note that if the MD3 display module has a loss of power or other malfunction the screen may go blank and all machine functions controlled by the computer system will be affected.

Once acknowledged this message will be replaced with a hardware fault message for the corresponding module when active faults are recalled to the screen. Refer to COMPUTER ~ MESSAGES - CRITICAL ~ HARDWARE FAULT in THIS SECTION.

2.66

Tigercat/FPT NEF No contact

Tigercat T234B Track Loader

Controls and Operation

MD3 MODULE BLANK SCREEN

The MD3 module is the central unit in the computer control system, which works as both a master and a display unit. Faults or failure in this unit will affect all other MD3 computer components.

Likely causes are: • Power - Fuse (MD3 module) • Ground • LCD display settings too light to read • Faulty MD3 module

2.67

Controls and Operation

Tigercat T234B Track Loader

ALERT MESSAGES (YELLOW) Alert messages advise the operator that machine operation will be compromised.

Alert messages have the second level of priority and are used to indicate to the operator that action is required to prevent future damage to the machine.

All alert message will give brief details of the fault and advise what action is necessary.

When a system generated alert message is displayed the external alarm and light will sound and flash three times to alert the operator of the message.

Action should be taken to service the machine to correct the problem at the earliest opportunity to prevent future damage to the machine.

The message remains on the screen until the operator hides it.

Note that active hardware fault alert messages are acknowledged by pressing the F2 button (OK). To recall these messages turn key off and on. On screen messages will indicate to the operator that an active hardware fault has been hidden.

234B-080

Alert messages flash the alert symbol above the F4 button when active messages are hidden.

Active messages that have been hidden can be reviewed by pressing the F4 button. The symbol will continue to flash until the problem is resolved and the fault becomes inactive.

Note that if both a critical level fault and an alert level fault are present the critical symbol will take priority until the critical fault becomes inactive.

There are two types of alert messages: Alert programmed messages generally triggered by machine function related conditions.

When an alert message is displayed, the external alarm and light will sound and flash three times to alert the operator of the message. The message remains on the screen until the operator hides it.

Messages can be hidden by pressing the F2 button (Hide).

Alert computer system generated messages are generally triggered by computer system error and fault related conditions.

2.68

Tigercat T234B Track Loader

Controls and Operation

INTERACTIVE ALERT MESSAGES

ENGINE FAULT CODE MESSAGES

•

Engine Fault Code - Alert

•

Engine Torque Derate Active

•

Charge Filter

SPN: #####

•

MD3 Controller

Contact service

•

Module XA2-A0

•

Module XA2-A1

•

Module XC21-A2

•

Module XC21-A3 (If Equipped)

•

Joystick Axis Fault

•

Swing Pedal Fault

•

Hoist Boom Limit Sensor Fault

•

Stick Boom Limit Sensor Fault

•

Control Selector Switch - Check Wiring

•

Control Selector Switch - Position Change

•

Hydraulic Oil Filter Restricted

•

Engine Air Intake Filter Restricted

•

Engine Voltage Low

•

Engine Voltage High

•

COUT hardware fault

•

DOUT hardware fault

•

DIN hardware fault

•

VIN hardware fault

•

Diesel Exhaust Fluid Quality

•

Diesel Exhaust Fluid Level

•

Water In Fuel

Alert engine fault message(s) will be displayed, alarm light will flash and alarm will sound when an alert engine fault message is received from the engine electronic control module.

They provide the SPN code (suspect parameter number) and the FMI code (fault mode identifier) as well as a message describing the fault (when available).

Alert engine fault codes are lower priority messages than critical level engine fault code messages. Alert messages can be hidden but action (service engine) is required to resolve the cause of the fault.

Note that some less common engine fault codes will appear without a message describing the fault. Make a note of the SPN and FMI codes and contact service for more information.

Refer to engine manufacturer's manual for specific information regarding the engine.

NOTE: Not all messages are shown.

2.69

Controls and Operation

Tigercat T234B Track Loader

ENGINE TORQUE DERATE ACTIVE

CHARGE FILTER FAULT

SPN: 64911 1 of 1

Charge Filter

Engine torque derate active

Bypassed. Service machine

This message will be displayed, alarm light will flash and alarm will sound when the Engine ECU has derated the engine. The code for a Torque Derate due to high NOx is shown above as an example.

Refer to Engine Manuals for code information to identify the cause(s) of engine derating and more information regarding failure cause and repair.

This message will be displayed when an alert level active fault related to the SWING PUMP HYDRAULIC CHARGE FILTER has been triggered.

Bypassed. Service machine alert message is an example of the type of fault that triggers this message. The charge pressure filter is restricted and requires service.

2.70

Tigercat T234B Track Loader

Controls and Operation

HYDRAULIC OIL FILTER RESTRICTION

JOYSTICK AXIS FAULT

RH Joystick Y-Axis Low Voltage

Machines are equipped with a 20 psi hydraulic oil filter bypass switch which will activate should the filters become restricted.

This message appears when a fault has been detected in one of the voltage outputs from the joystick axis. The message will indicate if the fault is in the LH or RH joystick and with the X or Y axis.

When this switch is activated the above message will appear.

If this message appears, all four hydraulic oil return filters should be replaced to prevent contamination to the hydraulic system which could lead to damage to hydraulic components.

2.71

Controls and Operation

Tigercat T234B Track Loader

HOIST BOOM LIMIT SENSOR

STICK BOOM LIMIT SENSOR

Hoist Boom Limit Sensor

Stick Boom Limit Sensor

Malfunction. Contact Dealer

Malfunction. Contact Dealer

Machines with electronic joystick option are equipped with a hoist boom limit sensor to help cushion the hoist cylinder at it's minimum and maximum stroke.

Machines with electronic joystick option are equipped with a stick boom limit sensor to help cushion the stick cylinder at it's minimum and maximum stroke.

This message will appear should there be a problem with the hoist boom limit sensor.

Determine what the problem is and have it repaired as soon as possible to prevent damage to the hoist cylinder.

This message will appear should there be a problem with the stick boom limit sensor.

Determine what the problem is and have it repaired as soon as possible to prevent damage to the stick cylinder.

2.72

Tigercat T234B Track Loader

Controls and Operation

SELECTABLE MACHINE CONTROL

SELECTABLE MACHINE CONTROL

Control Selector Switch

Control Selector Switch

Check switch wiring

position has changed. Verify control response before operating. Pilot reset required.

If machines are equipped with a selectable machine control switch the configuration of the joysticks and foot pedals can be changed to suit operator preference.

If machines are equipped with a selectable machine control switch the configuration of the joysticks and foot pedals can be changed to suit operator preference.

This message will appear should there be a problem with the wiring to the switch or the switch is in a position that is not supported by the MD3 computer system.

This message will appear if the rotary switch is turned while the pilot is on. Press the F2 button to confirm the selection and then press the pilot reset to activate the pilot system.

2.73

Controls and Operation

Tigercat T234B Track Loader

SWING PEDAL FAULT

HARDWARE FAULT - MD3

Swing Pedal CW

Hardware Fault - MD3

Low Voltage

Active fault has been hidden. Turn key off and on to recall active hidden hardware faults.

This message appears when a fault has been detected in one of the voltage outputs from the swing pedals. The message will indicate if the fault is in the CW or CCW swing pedal.

This message will be displayed when an alert level active hardware fault related to the MD3 Controller has been hidden.

To recall the original active fault(s) the operator must turn the key off and on.

High temperature, low supply voltage and high supply voltage module alert messages are examples of the type of hardware fault which will be the original active faults which trigger this message.

2.74

Tigercat T234B Track Loader

Controls and Operation

HARDWARE FAULT - XC21-A2

HARDWARE FAULT - XC21-A3

Hardware Fault - XC21-A2

Hardware Fault - XC21-A3

Active fault has been hidden. Turn key off and on to recall active hidden hardware faults.

Active fault has been hidden. Turn key off and on to recall active hidden hardware faults.

This message will be displayed when an alert level active hardware fault related to the XC21-A2 cab module has been hidden.

This message will be displayed when an alert level active hardware fault related to the XC21-A3 cab module has been hidden.

To recall the original active fault(s) the operator must turn the key off and on.

To recall the original active fault(s) the operator must turn the key off and on.

High temperature, low supply voltage and high supply voltage module alert messages are examples of the type of hardware fault which will be the original active faults which trigger this message.

High temperature, low supply voltage and high supply voltage module alert messages are examples of the type of hardware fault which will be the original active faults which trigger this message.

2.75

Controls and Operation HARDWARE FAULT - XA2-A0

Tigercat T234B Track Loader HARDWARE FAULT - XA2-A1

Hardware Fault - XA2-A0

Hardware Fault - XA2-A1

Active fault has been hidden. Turn key off and on to recall active hidden hardware faults.

Active fault has been hidden. Turn key off and on to recall active hidden hardware faults.

This message will be displayed when an alert level active hardware fault related to the XA2-A0 module has been hidden.

This message will be displayed when an alert level active hardware fault related to the XA2-A1 module has been hidden.

To recall the original active fault(s) the operator must turn the key off and on.

To recall the original active fault(s) the operator must turn the key off and on.

High temperature, low supply voltage and high supply voltage module alert messages are examples of the type of hardware fault which will be the original active faults which trigger this message.

High temperature, low supply voltage and high supply voltage module alert messages are examples of the type of hardware fault which will be the original active faults which trigger this message.

2.76

Tigercat T234B Track Loader

Controls and Operation

DIESEL EXHAUST FLUID QUALITY

SPN: 19402

SPN: 19658

DEF quality low.

DEF quality low.

This message will be displayed, alarm light will flash and alarm will sound when a diesel fluid quality problem is detected. Action to correct the problem should be taken immediately to avoid affecting engine performance and damage to the Selective Catalytic Reduction (SCR) aftertreatment system components.

WARNING Use only diesel exhaust fluid (DEF) which meets ISO 22241 specifications. NEVER fill the DEF tank with any other fluid.

DEF is injected into the exhaust gas stream during normal operation of the Selective Catalytic Reduction (SCR) aftertreatment system.

Use of other fluids may cause component damage, or a fire risk which could result in death or serious injury.

This message results in the following derate and engine lockout sequence if no action is taken to correct the problem: •

Beginning 1 hour after a Diesel Exhaust Fluid (DEF) quality message, there will be a ramp down of Engine Speed by 60% and Torque by 65% over 40 minutes.

•

After 2 hours at derated engine speed and torque the engine is derated to idle within 30 minutes.

•

A total of 3 restarts are allowed after any derate has started. Refer to COMPUTER – MESSAGES – CRITICAL–ENGINE LOCKED OUT and ENGINE RESTARTS REMAINING UNTIL ENGINE LOCKOUT in THIS SECTION.

To correct the DEF quality problem, clean the area around the DEF tank then drain and refill the tank with clean DEF which meets ISO 22241 specifications. Additional messages from the Denox Module will also be displayed. Refer to Engine Manuals for code information.

Note that an Engine Torque Derate Active message will also be triggered as the engine begins to derate. Refer to COMPUTER – MESSAGES – ALERT – ENGINE TORQUE DERATE ACTIVE. Refer to DIESEL EXHAUST FLUID TANK in THIS SECTION and DRAINING DIESEL EXHAUST FLUID TANK in SECTION 3.

Refer also to AFTERTREATMENT SYSTEM in SECTION 3 for more information regarding the use of DEF and its function in the SCR aftertreatment system.

2.77

Controls and Operation DIESEL EXHAUST FLUID LEVEL MESSAGES

Tigercat T234B Track Loader DIESEL EXHAUST FLUID LEVEL EMPTY

There are 3 levels of diesel exhaust fluid level messages generated by the Denox Module.

DIESEL EXHAUST FLUID LEVEL <10%

SPN: 64191 1 of 1 DEF tank empty.

SPN: 61839 1 of 1 DEF Level below 10%.

This message will be displayed, alarm light will flash and alarm will sound when a diesel exhaust fluid level below 10% is detected. Action to correct DEF levels should be taken immediately to avoid affecting engine performance and damage to the SCR aftertreatment system components.

Fill DEF tank and restart engine to clear the message.

Refer to DIESEL EXHAUST FLUID TANK in THIS SECTION.

This message will be displayed, alarm light will flash and alarm will sound when diesel exhaust fluid level empty is detected. Action to correct DEF levels should be taken immediately to avoid affecting engine performance and damage to the SCR aftertreatment system components.

•

Fill DEF tank and restart engine to clear the message.

Note that an Engine Torque Derate Active message will also be triggered as the engine begins to derate. Refer to COMPUTER – MESSAGES – ALERT – ENGINE TORQUE DERATE ACTIVE.

DIESEL EXHAUST FLUID LEVEL <5%

SPN: 62095 1 of 1 DEF Level below 5%.

This message will be displayed, alarm light will flash and alarm will sound when a diesel exhaust fluid level below 5% is detected. Action to correct DEF levels should be taken immediately to avoid affecting engine performance and damage to the selective catalytic reduction (SCR) aftertreatment system components.

•

Beginning immediately after a DEF level empty message, the engine is derated to idle within 30 minutes.

Beginning immediately after a DEF level <5% message, there will be a ramp down of Engine Speed by 60% and Torque by 65% over 40 minutes.

Fill DEF tank and restart engine to clear the message.

2.78

Tigercat T234B Track Loader

Controls and Operation

ENGINE VOLTAGE LOW

LOW FUEL LEVEL - MESSAGE AND ICON

SPN: 8801

1

Engine voltage low.

This message will be displayed when engine voltage readings of less than 20V are detected.

When this alarm is activated investigate the cause immediately.

234B-004

ENGINE VOLTAGE HIGH

The fuel icon (1) turns yellow and a Low Fuel Level message is displayed when the FUEL level drops below 76 L (20 gal US).

SPN: 4449

WAIT TO START

Engine voltage high.

This message will be displayed when engine voltage readings of greater than 30V are detected.

When this alarm is activated investigate the cause immediately.

WATER IN FUEL

SPN: 17429

This icon will appear on the display during the 'key ON' engine pre-heat time. Heating elements (grid heater elements) located in the engine air intake manifold are turned ON to heat the intake air when starting the engine. The engine must not be started until this icon turns OFF automatically.

Water in fuel.

This message will be displayed when water is detected in the fuel.

When this alarm is activated check the fuel filter/ water separator.

2.79

Controls and Operation

Tigercat T234B Track Loader

COLD WEATHER STARTING

NOTICE

During cold weather, the engine idle speed is controlled by the computer to limit maximum engine speed until the hydraulic system temperature has warmed to a specific temperature based on the oil grade selected.

TEMPERATURE

21°C (70°F)

• DO NOT IDLE THIS ENGINE FOR MORE THAN 9 HOURS. • DAMAGE TO EMISSION CONTROL SYSTEM WILL RESULT.

4.5°C (40°F)

63281BENG R0

1400 RPM

IMPORTANT! Engine should not idle longer than 9 consecutive hours. Damage to the emission control system will result. When this machine idles for an extended period excess hydrocarbon buildup is created in the SCR aftertreatment system. Burn off of excess hydrocarbon at full load immediately after a long idle period will generate excess heat which will cause damage to emission control system components. It will take 45 minutes at 40% load (or an SCR exhaust outlet temperature of 320°C [608°F]) to burn off the hydrocarbon that accumulates during a 9 hour long idle.

1850 RPM ENGINE SPEED

As the machine hydraulic system temperature rises the engine idle speed can be increased. The length of time it takes is dependent on ambient temperature and oil grade selected.

Example: ISO 46 oil grade at 21°C (70°F) or above, engine speed can be increased to maximum idle speed of 1850 rpm.

NOTE: The idle down function will not work until the engine idle speed can be increased to full rpm.

2.80

Tigercat T234B Track Loader

234-108

Controls and Operation

CAB FUSE AND RELAY PANEL

FUSE AND RELAY PANEL LABEL FUSE AND RELAY PANEL – CAB The fuse panel is located below the main display control panel behind a removable cover.

Each circuit of the machine is protected by a fuse.

If a fuse is blown it must be replaced by one of the same value. If the fuse blows again, the circuit should be inspected for possible short circuit or other malfunction.

2.81

Controls and Operation

234B-020

Tigercat T234B Track Loader

MAIN FUSE AND RELAY ELECTRICAL BOX

MAIN FUSE AND RELAY ELECTRICAL BOX LABEL FUSES AND RELAYS - ELECTRICAL BOX This Main Fuse and Relay electrical box is located in the engine compartment.

2.82

Tigercat T234B Track Loader

Controls and Operation

ECM FUSE

ECM FUSE

234B-271

ECM FUSE

Mounted directly under the battery disconnect switch is the ECM fuse. This fuse supplies power to the following fuses in the main engine fuse panel.

•

ECU power fuse

•

Def Lines fuse

•

Vacuum Relay fuse

•

Real Time Clock/After Run Relay

2.83

Controls and Operation

Tigercat T234B Track Loader

ENGINE COMPARTMENT

T234B-019

ENGINE COMPARTMENT ACCESS There are 3 access doors, 1 on the side, 1 on the rear, and 1 located on the front of the machine beside the cab. The rear door is opened by lifting the latch outwards and turn it 90° and swing the door open. The side door can be opened by unscrewing the 3 retaining bolts and swing the door open. The front access panel is removed by lifting the latches outwards, tuning them 90° and then lifting the panel up and out.

T234B-018

ENGINE COMPARTMENT ACCESS REAR BATTERY DISCONNECT SWITCH

BATTERY DISCONNECT SWITCH

ENGINE COMPARTMENT ACCESS FRONT

BATTERY DISCONNECT SWITCH This switch completely disconnects all electrical circuits (see note below) on the machine from the battery and is located just inside the front access panel. It is good practice to turn this switch to OFF whenever the machine is left idle for an extended period of time (overnight etc.).

234B-271

NOTE: This machine is equipped with an After Run Relay which delays the power disconnect to the engine ECU. This circuit is supplied power even if the battery disconnect switch is off, via a separate ECM fuse located directly below the battery disconnect switch. Whenever the engine is stopped, all DEF solution is pumped back to tank before the engine power system is turned off. This process takes approximately 90 seconds. See schematic ENGINE/BATTERIES SHEET 3 OF 3 in SECTION 6 of the SERVICE MANUAL. Also see FUSES AND RELAYS in THIS SECTION for details on the ECM fuse.

234E-275

ENGINE COMPARTMENT LEFT SIDE

2.84

Tigercat T234B Track Loader

Controls and Operation

FUEL TANK AND FILLER

REFUELING

The tank is located underneath the cab and has a capacity of 100 US gallons. The fuel filler is located on the front of the machine below the cab.

Park machine on level ground, shut off engine and allow machine to cool.

D

FILLER TUBE

DO NOT refuel while smoking or near an open flame or sparks.

Clear obstructions from steps and handles needed to access fuel tank.

Open cover on top of fuel tank (if equipped) and clear any debris from around the fill cap.

T234B-020

Remove filler cap slowly to allow pressure to escape from tank.

FUEL TANK AND FILLER

To add fuel to the tank place the fill nozzle in the inner fill tube, air from the tank will vent out via the air vent passage.

Inspect fill cap gasket.

Inspect fuel strainer located under the fill cap for debris or damage.

AIR VENT PASSAGE

Attach a grounding strap to an unpainted metal surface on the machine if the refueling tank or nozzle is so equipped.

INNER FILL TUBE

Fill tank until fuel level reaches the strainer or the full mark on the sight gauge if equipped. Do not leave nozzle unattended or spillage may occur.

Remove nozzle and ground strap (if applicable), then install fill cap hand tight before closing fill cap cover.

Before restarting the machine, check that no other personnel have moved into the hazardous area and sound the horn.

248-20

FUEL FILL TUBE

S≤15 mg/kg ULTRA LOW SULFUR FUEL ONLY 36686AUNI R0

2.85

Controls and Operation

Tigercat T234B Track Loader

DEF (DIESEL EXHAUST FLUID) TANK DEF TANK FILL CAP

Diesel exhaust fluid (DEF) is an aqueous urea solution with 32.5% high purity urea and 67.5% deionized water. Note that DEF may also be referred to as AUS32 or AdBlue. All DEF must be American Petrolium Institute (API) certified or meet ISO 22241 specifications.

41581AUNI R0

T250D-120

WARNING

DEF TANK COMPARTMENT

Use only diesel exhaust fluid (DEF) which meets ISO 22241 specifications. NEVER fill the DEF tank with any other fluid.

DEF is injected into the exhaust gas stream during normal operation of the Selective Catalytic Reduction (SCR) aftertreatment system.

Use of other fluids may cause component damage, or a fire risk which could result in death or serious injury.

The DEF tank is located in the compartment beside the boom saddle. The DEF tank fill cap can be accessed by lifting the hinged lid on top of the compartment. The DEF tank fill point is equipped with a filter to prevent contaminants from entering the tank.

DEF tank capacity is 43 L (11.4 gal US). DO NOT overfill tank. This tank is equipped with an expansion capacity of 7% required to allow for the expansion of DEF in cold temperature conditions.

DEF freezes at -11°C (12°F).

DEF is used by the SCR after-treatment system to lower the concentration of nitrogen oxides from the diesel engine exhaust of this vehicle.

A DEF level indicator is shown on the main menu of the computer display, below the fuel gauge.

It is important to avoid contamination of DEF when filling the tank as this may cause costly damage to SCR system components and affect the proper operation of the SCR system and the engine.

When DEF levels are low information messages will be shown on the computer display. Note that extremely low DEF levels may result in derating of engine performance to meet emission standard requirements. Action to correct DEF levels should be taken immediately to avoid affecting engine performance. Refer also to COMPUTER~MESSAGES in THIS SECTION.

When a problem with DEF quality is detected information messages will be shown on the computer display. Note that DEF quality problems may result in derating of engine performance to meet emission standard requirements. Action to correct DEF quality problems should be taken immediately to avoid affecting engine performance and damage to SCR after-treatment system components. Refer also to COMPUTER – MESSAGES in THIS SECTION.

The DEF tank and DEF supply lines are heated when temperatures are low, the system will thaw DEF within 30 minutes of engine start for proper operation of the SCR aftertreatment system. Note also that whenever the engine is stopped all DEF is pumped back to tank before the engine power system is turned off. This process takes approximately 90 seconds. Refer to AFTERTREATMENT SYSTEM in SECTION 3.

IMPORTANT! DEF should be stored between -11°C (12°F) and 30°C (86°F) and out of direct sunlight to maximize shelf life and to avoid DEF quality problems caused by improper storage.

Refer also to AFTERTREATMENT SYSTEM in SECTION 3 for more information regarding the use of DEF and its function in the SCR aftertreatment system.

2.86

Tigercat T234B Track Loader

Controls and Operation

HYDRAULIC OIL TANK HYDRAULIC OIL SIGHT GAUGE/ SENDER

234B-107

HYDRAULIC TANK

SIGHT GAUGE

HYDRAULIC OIL FILTERS

HYDRAULIC PUMPS LOW LEVEL SENDING UNIT

HYDRAULIC OIL SIGHT GAUGE/SENDER 234E-282

A sight gauge on the front of the tank is visible from the front access panel or the left hand side door. The hydraulic oil level must be kept between the HIGH and LOW limits at all times. A low level switch is incorporated into the level indicator.

When the hydraulic oil reaches this level the switch activates a critical alert message on the MD3 display.

HYDRAULIC OIL TANK

Allowing the level to drop below the LOW limit can result in severe damage to hydraulic components.

If the oil level drops, inspect the machine including all fittings and hydraulic components for leaks.

Once the source of the oil loss is located and repaired, oil can be added to the tank.

234B-003

2.87

Controls and Operation

Tigercat T234B Track Loader

HYDRAULIC HAND FILL PUMP

OIL FILL SHUTOFF VALVE

HAND FILL PUMP 234E-280

HYDRAULIC HAND FILL PUMP

The hydraulic hand fill pump is used to add oil to the hydraulic tank. It is located inside the engine compartment near the front left corner and is made accessible by removing the front access panel.

Adding Oil Prior to adding oil to the tank, determine and repair the source of the oil loss. Remove hose clamp from end of suction hose, remove hose from stored position, thoroughly clean outside surface of suction hose and insert end into supply drum. Open the oil fill shut off valve (ball valve located on top of the hand pump). Operate the pump by moving the handle back and forth at medium speed and a steady motion. The oil passes through the filters on the return lines of the hydraulic system. When the sight gauge reads between LOW and HIGH cease pumping and return handle to upright position. Close the oil fill shut off valve.

NOTE: Turning on the hydraulic tank vacuum pump will assist the filling procedure.

2.88

Tigercat T234B Track Loader

Controls and Operation

HYDRAULIC RETURN FILTERS

Each filter head has a bypass valve with a 1.7 bar (25 psi) cracking pressure so that oil can bypass the filters if they become restricted.

The 'in' side of the filter heads are connected to a return manifold. A filter restriction indicator and an oil sampling connector are mounted onto the manifold. Check the condition of the filter elements with the hydraulic oil at normal operating temperature. Place engine throttle control to FULL. With saw cut function operating, the filter restriction indicator should be in the GREEN zone.

If the pointer is in the RED zone replace all four filter elements.

RETURN MANIFOLD

HYDRAULIC PILOT FILTER ONE WATER ABSORBING (BLUE) RETURN FILTER

234E-282

LOCATED UNDER LEFT SIDE OF ENGINE COMPARTMENT THREE HYDRAULIC RETURN FILTERS

HYDRAULIC RETURN FILTERS

The majority of return oil entering the hydraulic tank passes through 4 spin-on hydraulic oil filters.

One of the filters is a water absorbing (blue) filter in place to assist with the removal of unwanted moisture from the hydraulic oil. The filters are rated 10 micron absolute.

PILOT FILTER ELEMENT

FILTER RESTRICTION INDICATOR 234E-279

HYDRAULIC PILOT FILTER

A single element filter head filters all pilot oil prior to entering the pilot system. The filter head has a built-in bypass valve with a 3.4 bar (50 psi) cracking pressure so that oil can bypass the filter if the element becomes restricted.

The return filters and the pilot filter should be checked and replaced as per the maintenance schedule in SECTION 3.

234E-278

HYDRAULIC OIL RETURN MANIFOLD

IMPORTANT! Contaminated hydraulic fluid can lead to premature failure of hydraulic components and costly repairs. Filters must be replaced at the recommended time intervals, See SECTION 3.

Use of hydraulic oil filters other than the Tigercat brand could lead to severe wear and rapid failure of hydraulic system components.

2.89

Controls and Operation

Tigercat T234B Track Loader

CASE DRAIN STRAINER

SWING PUMP CHARGE PRESSURE FILTER

CHARGE PUMP FILTER

PILOT FILTER ELEMENT

CASE DRAIN STRAINER

250CT-013

234E-275 250CT-014

FILTER AND STRAINER LOCATIONS

A case drain strainer element is located in the pump compartment and services the swing and main pump case drains, swing motor case drain, pilot return, pilot filter and charge pressure filter bypass.

234E-281

CHARGE PUMP FILTER

The swing pump charge pressure filter is a full flow filter mounted on a filter head with built-in bypass.

The filter is located in the output side of the charge pump mounted on the platform frame below the swing pump. For service and replacement intervals see SERVICE AND LUBRICATION CHART in SECTION 3.

CASE DRAIN STRAINER

The strainer element requires no regular maintenance over the life of the machine. This element requires maintenance only in the case of damage or contamination due to a hydraulic pump or motor failure.

IMPORTANT! The strainer element is NOT a filter element.

Always use the correct replacement element. Use of an incorrect (filter type) element will result in pump damage.

DIFFUSER/ STRAINERS

234B-003

HYDRAULIC TANK

RETURN DIFFUSERS/STRAINERS There are two reusable diffuser/strainers fitted to the return tubes inside the tank. The diffuser/ strainers should be inspected whenever the hydraulic tank is drained. See SERVICE AND LUBRICATION CHART in SECTION 3.

2.90

Tigercat T234B Track Loader

Controls and Operation

AIR CLEANER

SAFETY ELEMENT

The machine is also equipped with an engine air filter restriction sensor which sends a signal to the computer control system in the event of filter restriction. The engine air intake pressure icon turns YELLOW when service to the filter is required and turns RED, along with an ALERT message, when service to the air filter has reached a critical state.

PRIMARY ELEMENT 726D-006PLT

AIR FILTER ELEMENTS

The air cleaner on this machine uses 2 filter elements, a primary element and a safety element.

234B-005

AIR CLEANER UNLOADER VALVE

To ensure maximum engine protection, it is important that the elements be serviced correctly and at proper servicing intervals.

AIR FILTER RESTRICTION INDICATOR AIR FILTER RESTRICTION INDICATOR

PRECLEANER

AIR FILTER RESTRICTION INDICATOR AIR CLEANER UNLOADER VALVE 234B-353

AIR CLEANER 234B-106

ENGINE

A filter restriction indicator is located in the engine enclosure beside the air cleaner. The indicator is remote mounted and is connected to the outlet side of the air filter with a 6 mm (1/4 in) diameter hose. Replace the primary air filter when the restriction indicator shows RED. This indicator provides a continuous reading whether the engine is running or is shut down. After replacing the filter, reset the indicator by pressing the reset button.

This rubber valve on the tube of the air cleaner housing should be checked at the beginning of every shift. (8 hours) If this valve is missing, damaged or has become hard, it will cause the air cleaner to become ineffective. The unloader valve should be replaced every 1000 hours.

Remove the unloader valve from the tube of the air cleaner housing.

Check and clean the valve. A good valve should be soft and flexible. If it is plugged, then check the filter elements, they may need replacing. Reattach the valve to the tube.

The valve should suck closed at about 1/3 of full throttle. When operating in high dust conditions this valve should be checked and squeezed every 2 hours to release dust buildup.

NOTE: Replace the safety element every third primary filter change.

2.91

Controls and Operation

Tigercat T234B Track Loader

AIR PRECLEANER

OPERATION: 1. Air enters the precleaner.

3

3

2. Specially designed vanes move dirty air toward the impeller.

4

3. The spinning impeller spins the air creating centrifugal force to separate contaminants from the clean air.

4. Contaminants are blown out the discharge louver.

2 1

5. Clean air enters the intake to the air cleaner.

INTAKE TUBING AND JOINTS

5

AIR INTAKE ELBOWS 480-017

PRECLEANER OPERATION

The engine air precleaner cleans engine air before it reaches the air cleaner filter elements. It removes contaminants such as dust, powder, insects, rain, and snow. The air precleaner should be checked every 8 hours to make sure that foreign materials have not plugged the intake area or the discharge louver area. Clean as required.

AIR INTAKE TUBE

IMPORTANT! The air precleaner must be checked every 8 hours and cleaned as required.

If the inlet/precleaner is plugged causing a restriction to airflow, reduced engine performance and increased fuel consumption may result.

If a plugged inlet/precleaner is left too long, excessive air intake restriction may damage the rubber air intake tube. A damaged air intake tube will lead to ingestion of dirt into the engine which may result in engine failure.

Note that the air filter restriction indicator may not function properly if the air intake tube is damaged.

Engine failures due to improper maintenance are not covered by Tigercat or Engine Manufacturer’s Warranty and any such claim will be denied.

234B-106

ENGINE COMPARTMENT

Check all air intake system components, rubber elbows, connector hoses, tubes and clamps for damage, hardening, wear, cracks, leaks, loose clamps or loose hanger bracket hardware. Repair or replace immediately.

Replace all air intake rubber components such as elbows and connectors every 2000 hours. High temperatures in this area can cause the rubber to harden.

NOTE: High-temperature silicone connectors do not need to be replaced unless they are damaged.

IMPORTANT! For peak engine performance and maximum fuel economy, please ensure that the air precleaner is regularly checked and cleaned as required. All intake air tubes and clamps should be thoroughly inspected on a regular basis and any damaged or missing components should be replaced immediately.

2.92

Tigercat T234B Track Loader MACHINE OPERATION

Controls and Operation

Prior to operating the machine, ensure that the proper lubrication and maintenance schedule has been performed as outlined in SECTION 3.

FILLER TUBE

For the Diesel Engine supplied with the machine, Refer to the engine manufacturers operator’s manual .

Any personnel who is to operate this machine must be fully trained in safety and operating procedures by a competent person.

Read and understand this entire manual prior to operating machine.

PRE-START CHECKS FUEL TANK AND FILLER 3. Check fuel level.

T234B-020

1

SIGHT GAUGE

234-106

KEY SWITCH - OFF

1. Ensure Key (1) switch is in the OFF position.

LOW LEVEL SENDING UNIT CHECK FIRE EXTINGUISHER

234B-107

CHECK HYDRAULIC OIL LEVEL

4. Check that the hydraulic oil level is between the HIGH and LOW marks on the level gauge.

234B-354

234-095

PORTABLE FIRE EXTINGUISHER

2. Check fire extinguisher is sufficiently charged.

HALF FILL RESERVOIR WITH RECOMMENDED OIL AS SPECIFIED IN SECTION 3

SWING DRIVE GEARBOX OIL RESERVOIR 5. Check swing drive gearbox oil level.

2.93

Controls and Operation

Tigercat T234B Track Loader

ENGINE OIL LEVEL DIPSTICK

AIR FILTER RESTRICTION INDICATOR

CHECK ENGINE OIL LEVEL 234E-283 6. Check that the engine oil level is between the ADD and FULL marks on the dipstick.

AIR CLEANER UNLOADER VALVE 234E-284

9. Check air filter restriction indicator.

CHARGE AIR COOLER

RADIATOR COOLANT LEVEL SIGHT GLASS A/C CONDENSER

OIL COOLER

234E-285

CHECK ENGINE COOLANT LEVEL

7. Check engine coolant level.

234E-288

CHECK CHARGE AIR COOLER, RADIATOR, A/C CONDENSER AND OIL COOLER 10. Check charge air cooler/radiator/A/C condenser/oil cooler package, and all screens and doors.

11. Ensure all doors and access panel are closed and/or securely fastened.

SERPENTINE FAN BELT

234E-285

A/C COMPRESSOR BELT

CHECK ENGINE BELTS

8. Check tension and condition of all engine belts.

2.94

Tigercat T234B Track Loader

Controls and Operation

T234B-021

T234B-059

ROTARY SWITCH

RESERVOIR

SELECTABLE MACHINE CONTROL ROTARY SWITCH 16. If the machine is equipped with selectable machine control check the position of the rotary switch to verify control response.

CHECK WINDSHIELD WASHER LEVEL 12. Check windshield washer fluid level.

17. Perform SCHEDULED MAINTENANCE as outlined in SECTION 3.

13. Inspect machine for leaks, damaged or loose components or any other abnormal conditions.

14. Ensure all doors and access panels are closed and securely fastened.

18. Turn Ignition switch on to check fuel and DEF levels on MD3 display. If required, fill with the appropriate fluids.

15. If cab has been tilted, ensure that it is secured to the frame with the locking bolts.

2.95

Controls and Operation

Tigercat T234B Track Loader

STARTING THE ENGINE

CAUTION

1. Ensure that PRE-START CHECKS have been performed and that the area is clear of personnel prior to starting the engine. Refer to OPERATING MACHINE - PRE-START CHECKS in THIS SECTION.

Do not start engine by shorting across starter terminals. Start engine only from operator's seat.

WARNING

2. Turn ignition key switch to the RUN position. The WAIT TO START icon below will appear on the display during the “key ON” engine pre-heat time. Heating elements (grid heater elements) located in the engine air intake manifold are turned ON to heat the intake air when starting the engine. The engine must not be started until this icon turns OFF automatically.

Do not attempt to operate any function or accessory while starting the engine. Serious injury or property damage may result.

CAUTION To prevent damage to starter, do not engage starter motor for more than 15 to 20 seconds. Wait 2 minutes between each attempt to start the engine.

If engine fails to start, refer to engine manufacturers operator's manual.

WARNING • EXPLOSION HAZARD. • DO NOT USE ETHER. • ENGINE EQUIPPED WITH HEATER STARTING AID. • USE OF ETHER COULD RESULT IN DEATH OR SERIOUS INJURY. 36782BENG R0

3. Sound horn to warn personnel of machine start-up.

4. Then turn ignition key switch to the START position

to crank engine.

5. When the engine starts, release the ignition key switch to the ON position.

NOTE: If the engine does not start after three attempts, check the fuel supply system.

CAUTION After engine has started, keep engine speed low until engine oil pressure registers on gauge. If it does not register within 10 seconds, stop engine and investigate cause.

Allow a cold engine to warm up at LOW IDLE for at least five minutes before applying any load. Check all gauges regularly during the warm-up period.

2.96

Tigercat T234B Track Loader

Controls and Operation RESTARTING AN ENGINE THAT HAS RUN OUT OF FUEL

NOTICE

If the engine runs out of fuel perform the following: 1. Ensure key switch is turned to OFF

.

2. Refill fuel tank completely. See REFUELLING earlier in THIS SECTION. T234B-014

HAND PRIMER VENT PLUG • DO NOT IDLE THIS ENGINE FOR MORE THAN 9 HOURS. • DAMAGE TO EMISSION CONTROL SYSTEM WILL RESULT.

63281BENG R0

IMPORTANT !

Engine should not idle longer than 9 consecutive hours. Damage to the emission control system will result. When this machine idles for an extended period excess hydrocarbon buildup is created in the SCR aftertreatment system. Burn off of excess hydrocarbon at full load immediately after a long idle period will generate excess heat which will cause damage to emission control system components. It will take 45 minutes at 40% load (or an SCR exhaust outlet temperature of 320°C (608°F)) to burn off the hydrocarbon that accumulates during a 9 hour long idle.

FUEL FILTER / WATER SEPARATOR 3. Turn the key switch to the RUN position to turn on the fuel shut off solenoid. Loosen the vent plug on top of the fuel filter/water separator head. Use primer pump to refill filter until fuel free of air flows from vent on top of filter head, then tighten vent plug. Turn key switch off and repeat. As well, bleed the system according to engine manual procedures.

4. Crank engine until it starts. If it fails to start after 20 seconds, stop and wait for two minutes before trying again.

IMPORTANT! To prevent damage to starter, do not engage starter motor for more than 15 to 20 seconds.

Wait two minutes between each attempt to start the engine. If engine fails to start, refer to engine manufacturer operator’s manual.

2.97

Controls and Operation

Tigercat T234B Track Loader

MACHINE PREPARATION

(k) Test all accessory equipment including delimber, top saw, slasher saw etc.

Prior to commencing any log loading operations follow steps (a) through (p) to accomplish the following: •

Warm up the hydraulic system.

•

Test all systems for proper operation.

•

Inspect for hydraulic oil leaks.

NOTE: The right-hand joystick button performs two separate functions depending on the status of the delimber arms. With delimber arms closed the button operates the top saw. With the delimber arms open the button operates the slasher saw. (l) Continue testing and operating various functions until engine and hydraulic oil has warmed up to near normal operating temperatures. Never load the machine until it has sufficiently warmed up. Doing so may cause damage to the engine and hydraulic components.

IMPORTANT! If any system or function fails to respond correctly to the controls, stop the machine preparation procedure and notify a mechanic.

Failure to do so may result in damage to hydraulic pumps and other components. (a) Perform Pre-Start Checks, Starting the Engine and Setting the Machine procedures as outlined in THIS SECTION.

(m) Lower the grapple onto the trailer, carrier or stable ground ensuring grapple and booms are fully supported.

(b) Sound horn to warn personnel of machine operation.

ALARM LIGHT

(n) Set engine speed to LOW IDLE. (o) Exit cab and visually inspect machine for leaks or other machine damage. Ensure that machine is in proper working order and is in safe condition before continuing operation.

MASTER ALARM

WARNING 234-107

(c) Ensure computer display and warning light are indicating normal operating conditions. (d) Check that all personnel are safe and clear of the machine.

Never use your bare hand to check for fluid leaks.

Fluid leaks under pressure may not be visible.

When searching for leaks, wear work gloves and use a wrench or piece of wood to move hydraulic hoses. Do not grab hold of hydraulic hoses. Wear safety goggles for eye protection.

(e) Ensure both armrests are in the lowered position and press the Pilot Reset button. (f) Set engine speed to warm-up position (1400 rpm). (g) Ensure grapple and booms are not attached, chained or clamped around trailer or any other stationary object. (h) Slowly raise and lower the hoist boom and stick boom and check for proper operation. (i) With the grapple raised slightly off the ground, test the grapple rotate in both directions and test the open and close functions. (j) Operate the swing in both direction to ensure proper operation.

2.98

Tigercat T234B Track Loader

Controls and Operation

STOPPING THE ENGINE

Note that whenever the engine is stopped all DEF solution is pumped back to tank before the engine power system is turned off. This process takes approximately 90 seconds. Refer to AFTERTREATMENT SYSTEM in SECTION 3 for more information.

IMPORTANT! Stopping the engine immediately after it has been working under load can result in overheating and premature wear of the engine components. Follow the stopping procedure outlined below to allow the engine to cool.

Note also that this machine is equipped with an After Run/ Accessory Relay which delays by 90 seconds the power disconnect to engine related fuses and relays (ECM /ATS relay, NOx Sensor relay, NOx Sensor fuse, ECM Power fuse, DCU fuse).

Always follow this engine shut down procedure. The important benefits are: •

Extended life of engine, cooling and exhaust systems.

•

Reduced risk of post shutdown fires.

•

Interior of machine cools significantly reducing risk of touching hot surfaces.

IMPORTANT! Only use the master disconnect to shut off a running machine in an emergency. A fault code will be logged by the ECM on the engine for improper shut down and power down.

1. Ensuring grapple and booms are fully supported by lowering grapple onto the trailer, carrier or stable ground.

2. Reduce engine speed to LOW IDLE and continue to run for about three minutes to allow gradual dissipation of heat and also to reduce turbo speed. This will prevent loss of coolant by after boil and possible hot spot damage to the engine.

3. Ensure all controls are in neutral positions and that all accessories and functions are turned off.

4. Do not race engine before shut-off 5. Stop engine by turning Key switch to the OFF position.

6. Ensure grapple and booms are fully supported and that all functions are turned off. Remove key from switch, lock up cab and turn battery disconnect switch to OFF prior to leaving the machine.

7. Perform daily maintenance at the end of the shift (greasing, clean engine compartment etc.). This allows the machine time to cool down while under the watchful eye of the operator.

2.99

Controls and Operation CLEANING COOLER PACKAGE

Tigercat T234B Track Loader PROCEDURE:

The A/C condenser core is located on the right side of the machine and is one of the cores in a stack of four that make up the cooler package.

The cooling fan is mounted on the front of the engine. The fan draws air from the right side of the machine through the door screen and the cooler package blowing it out of the opposite side of the machine.

CHARGE AIR COOLER T250D-029

OPEN THE SCREEN DOOR ON R.H. SIDE OF ENGINE COMPARTMENT

RADIATOR

A/C CONDENSER

Remove the 3 bolts and washers and swing open the screen door on the right side of the engine compartment.

CAUTION

OIL COOLER

• If using compressed air for cleaning, use at 2 bar (30 psi) or less.

• Always use personal protective equipment to guard against flying debris.

234E-288

CHECK CHARGE AIR COOLER, RADIATOR, A/C CONDENSER AND OIL COOLER The cooler package should be manually checked every 8 hours (every shift) or more often where conditions cause accumulation of twigs, leaves, pine needles and dust. All of the engine enclosure doors should also be checked.

This cooler package must be checked daily and may require thorough cleaning on a regular basis depending on operating conditions. Compressed air or water may be used for cleaning. Use personal protective equipment to guard against flying debris.

If an oil leak occurs in this area it should be thoroughly power-washed with a mild soap to ensure that all of the oil is removed. The presence of oil causes dust and dirt to cling to surfaces which will impair the reversible fan's ability to remove dust and dirt particles.

Care must be taken when cleaning this unit, as the components can be damaged by careless handling and cleaning.

2.100

Tigercat T234B Track Loader

Controls and Operation

CARE OF MACHINE

CARE OF POLYCARBONATE WINDOWS IN CAB

1. Ensure that all fluid levels are always at the proper level. Refer to the LUBRICATION AND MAINTENANCE SCHEDULE provided in SECTION 3.

2. Follow proper procedure for cleaning windows described in this section.

3. Lubricate all necessary points as per the maintenance schedule provided.

4. Never apply a load to a cold engine.

5. Close and secure all doors and access panel prior to operating machine.

6. Clean machine including all platforms, inside engine enclosure and around radiator of all dirt and debris on a regular basis.

7. Keep all steps, ladders and platforms clear of oil and other material or debris that can cause an unsafe condition.

8. Ensure grapple head or boom is resting securely before shutting down the machine or servicing.

Most windows used in the cab are made from a polycarbonate resin thermoplastic. This material is a replacement for glass when improved strength, durability and safety is required.

Polycarbonate material is expected to resist heavy impact from large branches and falling tree tops and to absorb high levels of energy when contacted by high velocity thrown objects such as wood chips, disc saw blade teeth or broken harvester head saw chain.

The extreme operating environment seen in logging applications heightens the need to regularly inspect and properly maintain polycarbonate cab windows.

Polycarbonate windows are an essential piece of operator protective equipment and should be maintained as such. It is important to note that cracks, chips, notches or scarring anywhere on the viewing surface or edges of the window will decrease ability to resist heavy impacts and therefore compromise effectiveness as operator safety protective equipment. Windows with these defects must be replaced immediately.

Refer to the next section for detailed information regarding inspection and maintenance of polycarbonate windows.

2.101

Controls and Operation

Tigercat T234B Track Loader

INSPECTION AND MAINTENANCE

RESISTANCE TO CHEMICALS The resistance of polycarbonate material to chemical exposure varies widely. Fortunately, polycarbonate materials have good resistance to diesel fuel, grease, hydraulic oil, kerosene and engine oil.

Daily inspection and maintenance is essential to confirm that the window’s ability to protect the operator has not been compromised.

• Inspect all windows daily and immediately after any impacts.

•

•

•

•

Other chemicals however can seriously weaken the polycarbonate.

Check for any damage to the window material or steel structure in the area of the window mounting.

The edges of the polycarbonate window must be evenly and fully supported on a flat surface around the entire window opening at all times.

Bent or dented skylight structures must be replaced immediately. Bent or dented cab structures must be evaluated immediately for possible repair or replacement.

The edges of the polycarbonate window must be free from cracks, chips, notches or scarring and must not be pinched or stressed.

These defects will decrease ability to resist heavy impacts. Windows with these defects must be replaced immediately.

Cracks, chips, notches or scarring anywhere on the viewing surface of the window will decrease ability to resist heavy impacts.

Windows with these defects must be replaced immediately.

•

Bent, dented or missing window retaining parts must be replaced immediately.

•

Rubber materials used in mounting the window must be maintained in good condition.

•

Identification of the polycarbonate originally used by Tigercat is hot stamped in a corner of the window to identify its composition. Do not use any replacement window without proof of its material composition. Do not substitute with any other materials.

•

Skylights, cab structures, windows and window retaining parts must not be modified or replaced with components that are not approved by Tigercat.

DO NOT permit any of the following chemicals to come into contact with polycarbonate windows: •

Acetone

•

Air conditioning refrigerant

•

Ammonia

•

Anti-freeze

•

Benzene

•

Brake fluid

•

Carbon tetrachloride

•

Cutting oils

•

Gasoline

•

Acquer thinner

•

Toluene

•

Turpentine

•

Xylene

RESISTANCE TO WATER Polycarbonate material has good resistance to water up to approximately 65°C (150°F). Above this temperature the effect of water is timetemperature related. This means that the higher the water temperature, the shorter the time before the polycarbonate is adversely affected.

Exposing polycarbonate to repeated steam cleaning or high temperature pressure washing may result in crazing, a phenomenon that causes clouding of the surface. Crazing can ultimately result in a loss of physical strength and may precede a fracture.

2.102

Tigercat T234B Track Loader

Controls and Operation

CLEANING INSTRUCTIONS

CAUTIONS

The viewing surfaces of polycarbonate cab windows are specially treated with a hard coating to provide enhanced resistance to abrasion and ultra-violet (UV) radiation.

•

DO NOT use abusive cleaning procedures either by hand or pressure washing on polycarbonate windows.

•

DO NOT use brushes, razor blades, scrapers, squeegees or other sharp tools on polycarbonate windows.

•

DO NOT clean polycarbonate windows when the daytime temperature is high or in direct sunlight.

•

DO NOT use abrasive or highly alkaline cleaners on polycarbonate windows.

•

DO NOT use glass cleaners in either aerosol or non-aerosol containers to clean polycarbonate windows.

•

Failure to follow these cleaning instructions will shorten the service life of polycarbonate and may cause visual hazing, loss of light transmission and delamination of the polycarbonate hard surface coating.

The following instructions are provided to prolong the life of this protective hard coating.

1. Rinse the window thoroughly with lukewarm water 2. Using a soft cloth, cellulose sponge or chamois, gently wash the window with a mild solution of soap or detergent in lukewarm water. Do not scrub or use brushes or squeegees.

Brand name soaps and detergents recommended for cleaning polycarbonate are: • Fantastik • Formula 409 • Hexcel F.O. 554 • Joy • Lysol • Mr. Clean • Neleco-Placer • Pine-Sol • Top Job 3. Rinse the window thoroughly with lukewarm water.

4. Dry the window with a moist soft cloth, cellulose sponge or chamois to prevent water spotting.

5. To remove grease or oil, first rub lightly with a good grade of VM&P Naphtha or isopropyl alcohol followed by the same rinse, wash, rinse and dry procedure described in steps 1 to 4.

CONCEALING HAIRLINE SCRATCHES The appearance of scratches and minor abrasions on the surfaces of polycarbonate windows can be minimized by using a mild automotive polish such as: • • •

Johnson’s Paste Wax Novus Plastic Polish #1 and #2 Mirror Glaze Plastic Polish

Be certain to clean the polycarbonate window as outlined prior to application of an automotive polish. Refer to CLEANING INSTRUCTIONS.

Refer also to RESISTANCE TO CHEMICALS for a list of chemicals which should not be permitted to come into contact with polycarbonate windows.

2.103

Controls and Operation

Tigercat T234B Track Loader

GRAFFITI REMOVAL •

For removal of paints, marking pen inks, etc., the use of Butyl Cellosolve is generally effective. The use of masking tape, adhesive tape or lint removal tools works well for lifting off old weathered paints.

•

To remove labels, stickers, etc., the use of kerosene, VM&P Naphtha, or petroleum spirits is generally effective. When the solvent will not penetrate sticker material, apply heat (hair dryer) to soften the adhesive and promote removal.

•

WINDOW SCREEN HAND KNOB

Refer also to RESISTANCE TO CHEMICALS for a list of chemicals which should not be permitted to come into contact with polycarbonate windows.

FIRE PRECAUTIONS Polycarbonate window material will ignite when exposed to an ignition source in excess of 427°C (800°F). When working around polycarbonate windows, observe similar fire precautions to those in place for wood.

SIDE WINDOW SCREEN SIDE WINDOW SCREENS T234B-022

The side window screens (if equipped) can be opened to clean the windows. Screens are provided for the personal protection of the operator and must be closed immediately after cleaning the windows.

20231A R1

A hand knob is provided on both the inside and the outside. By unscrewing either (not both) of these knobs, the screen will be free to swing out on the hinges.

All handles should be hand tight only at all times.

2.104

Tigercat T234B Track Loader SECTION 3 – LUBRICATION AND MAINTENANCE CONTENTS - SECTION 3

ISSUE 1.5, APRIL 2016

AFTERTREATMENT SYSTEM AFTERTREATMENT COMPONENTS.................................................................................................. 3.38 APPROVED ANTI-SEIZE PASTES...................................................................................................... 3.46 CATALYTIC CONVERTER................................................................................................................... 3.43 DEF INLET STRAINER....................................................................................................................... 3.33 DIESEL EXHAUST FLUID (DEF) HANDLING...................................................................................... 3.47 DIESEL EXHAUST FLUID (DEF) TANK............................................................................................... 3.40 DIESEL OXYDATION CATALYST (DOC)............................................................................................. 3.42 DOC/SCR AFTERTREATMENT SYSTEM........................................................................................... 3.39 DOSING MODULE (DEF INJECTOR).................................................................................................. 3.43 EXHAUST FLAP................................................................................................................................... 3.42 HEATED DEF SUPPLY LINES............................................................................................................. 3.41 HEATER VALVE................................................................................................................................... 3.41 HUMIDITY SENSOR............................................................................................................................ 3.44 MIXER TUBE........................................................................................................................................3.43 NH3 SENSOR...................................................................................................................................... 3.45 NOX SENSOR...................................................................................................................................... 3.45 SUPPLY MODULE................................................................................................................................ 3.42 TEMPERATURE SENSORS................................................................................................................ 3.44 AIR CLEANER.........................................................................................................................................3.35 AIR CONDITIONING................................................................................................................................ 3.48 AIR INTAKE SYSTEM.............................................................................................................................. 3.34 AIR CLEANER...................................................................................................................................... 3.34 AIR CLEANER UNLOADER VALVE..................................................................................................... 3.34 AIR FILTER RESTRICTION INDICATOR............................................................................................. 3.34 AIR FILTER RESTRICTION SENSOR................................................................................................. 3.34 COMPUTER ALERT MESSAGE.......................................................................................................... 3.34 AIR INTAKE TUBING AND JOINTS......................................................................................................... 3.35 AIR PRECLEANER.................................................................................................................................. 3.36 APPROVED HYDRAULIC OILS.............................................................................................................. 3.14 CASE DRAIN STRAINER........................................................................................................................ 3.22 COOLER PACKAGE, CLEANING............................................................................................................ 3.49 DEF (DIESEL EXHAUST FLUID) DIESEL EXHAUST FLUID (DEF) HANDLING...................................................................................... 3.47 DRAINING THE TANK.......................................................................................................................... 3.33 TANK.....................................................................................................................................................3.40 FILTERS CHARGE PUMP FILTER WARNING.................................................................................................... 3.23 DEF DOSING MODULE....................................................................................................................... 3.28 ENGINE................................................................................................................................................3.25 FILTER REMOVAL TOOL..................................................................................................................... 3.26 FUEL FILTER / WATER SEPARATOR.................................................................................................. 3.26 HYDRAULIC OIL RETURN.................................................................................................................. 3.20 PILOT PRESSURE............................................................................................................................... 3.22 SWING PUMP CHARGE PRESSURE................................................................................................. 3.23 FIRE PREVENTION................................................................................................................................... 3.7 FUEL FILTER / WATER SEPARATOR..................................................................................................... 3.26 FUEL, REFUELING.................................................................................................................................. 3.24 FUEL TANK AND FILLER......................................................................................................................... 3.24

Lubrication and Maintenance

Tigercat T234B Track Loader

HAND FILL PUMP.................................................................................................................................... 3.19 HYDRAULIC OIL HYDRAULIC OIL LOW LEVEL SWITCH.............................................................................................. 3.17 HYDRAULIC OIL LOW LEVEL WARNING........................................................................................... 3.17 RETURN DIFFUSERS/STRAINERS.................................................................................................... 3.22 TANK.....................................................................................................................................................3.17 HYDRAULIC OIL RETURN FILTERS....................................................................................................... 3.20 HYDRAULIC TANK VACUUM SYSTEM.................................................................................................. 3.18 LUBRICATION AND SERVICE POINTS.................................................................................................. 3.12 NEW MACHINE MAINTENANCE FIRST 125 HOUR INSPECTION REPORT............................................................................................ 3.3 INITIAL PRE-DELIVERY INSPECTION.................................................................................................. 3.3 OIL LOST FROM LEAKAGE...................................................................................................................... 3.6 OIL SAMPLE COLLECTION PROCEDURES............................................................................................ 3.5 OIL SAMPLING PROGRAM....................................................................................................................... 3.4 PAG OIL...................................................................................................................................................3.48 PILOT PRESSURE FILTER..................................................................................................................... 3.22 PRESSURE SETTINGS................................................................................................................. 3.50, 3.51 PREVENTIVE MAINTENANCE SCHEDULE............................................................................................. 3.3 REFRIGERANT........................................................................................................................................3.48 REFUELING.............................................................................................................................................3.24 ROTARY MANIFOLD LUBRICATION...................................................................................................... 3.16 SCHEDULED MAINTENANCE EVERY 8 HOURS................................................................................................................................... 3.8 EVERY 24 HOURS................................................................................................................................. 3.8 EVERY 125 HOURS............................................................................................................................... 3.9 EVERY 250 HOURS............................................................................................................................... 3.9 EVERY 500 HOURS:............................................................................................................................ 3.10 EVERY 1000 HOURS........................................................................................................................... 3.10 EVERY 2000 HOURS........................................................................................................................... 3.11 GENERAL...............................................................................................................................................3.6 SERVICE AND LUBRICATION POINTS.................................................................................................. 3.12 STRAINER, CASE DRAIN....................................................................................................................... 3.22 SWING DRIVE LUBRICATION GEARBOX LOWER BEARINGS......................................................................................................... 3.15 GEARBOX UPPER GEARING............................................................................................................. 3.15 TORQUE CHART, GENERAL.................................................................................................................. 3.53 TORQUE, FLUID CONNECTIONS...................................................................................... 3.54, 3.55, 3.56 TORQUE SETTINGS, RECOMMENDED................................................................................................ 3.52 VACUUM SYSTEM, HYDRAULIC TANK................................................................................................. 3.18 WEIGHTS OF COMMERCIAL WOOD..................................................................................................... 3.57

3.2

Tigercat T234B Track Loader

Lubrication and Maintenance

PREVENTIVE MAINTENANCE SCHEDULE

WARNING

NEW MACHINE MAINTENANCE INITIAL PRE-DELIVERY INSPECTION Perform the initial pre-delivery inspection using tigercat form numbers 5337 and 5347: PDI and 125 hour inspection report.

WARNING, HOT FLUIDS AND HOT MACHINE SURFACES CAN CAUSE SERIOUS BURNS!

FIRST 125 HOUR INSPECTION AND SERVICE REPORT With the owner's mechanic present, perform an inspection and service according to the Tigercat form numbers 5337 and 5347: PDI and 125 hour inspection report.

• Before servicing the machine, allow the engine cooling system, fuel system, exhaust system, hydraulic system and machine surfaces to cool down.

This must be completed within the first 125 hour time frame.

• Use a thermometer to check surface and system temperatures to ensure it is safe to begin service work.

IMPORTANT! To qualify for continued warranty, this report must be completed and returned to Tigercat Industries Inc. Warranty department.

• DO NOT begin service work until the surface or system temperature has cooled down to below 38°C (100°F)!

TIGHTENING POINTS All hydraulic connections

CAUTION

Hose clamps

All handles, steps and platforms must be kept free of grease, oil, fuel mud, snow ice and forest debris to prevent risk of personal injury.

All cylinder and boom pin retainers Check swing bearing bolt torque Engine mounting bolts Pump mounting bolts

IMPORTANT!

Track shoe bolts

BEFORE DRIVING MACHINE ENSURE THAT THE TRACK TENSION (SAG) IS SET CORRECTLY.

Track roller retaining bolts Track sprocket retaining bolts

TRACK SAG MAY BE SET LESS THAN SPECIFIED FOR SHIPPING PURPOSES.

Track drive gearbox mounting bolts Track drive motor mounting bolts Swing gearbox mounting bolts Swing motor mounting bolts Cab securing bolts Any other loose nut, bolt or fitting

UNDERSIDE OF TRACK GUARD

NOTE: Use of filters other than genuine Tigercat replacement filters is not recommended.

SAG DIMENSION

UPPER SURFACE OF TRACK SHOE

Refer to diesel engine service manual and attachment manual for additional required maintenance at this scheduled time period.

853ILL8

MEASURING SAG DIMENSION

REFER TO SECTION 11 IN THE SERVICE MANUAL FOR THIS PROCEDURE.

3.3

Lubrication and Maintenance

Tigercat T234B Track Loader

TIGERCAT OIL SAMPLING PROGRAM

TIGERCAT OIL ANALYSIS KITS Each kit includes a Pre-paid Sample Bottle and Sample Information Form. Pre-printed mailing labels are also included to ensure all samples are quickly returned directly to the lab for immediate analysis and results within 24 hours of receipt.

Effective for all 2008 model year 200 series log loaders sold in USA and Canada, oil sampling must be performed during the warranty period as per the schedule below. Warranty coverage of Powertrain components, specifically main pump, pilot pump (if applicable), swing pump (if applicable), rotary manifold, swing motor, swing gearbox and swing bearing, main control valves, track motors and final drive gearboxes (if applicable) is contingent on performance of regular oil sampling at the owner’s expense during the warranty period.

The same type of sample bottle can be used for all types of oil testing including: Hydraulic Circuits, Final Drives, Axles, Gearboxes, Engines, etc.

To ensure accurate and meaningful results are obtained, each kit also includes detailed instructions on how properly collect, prepare and ship the oil samples.

FIRST SAMPLE There will be no charge for the first oil samples required to be taken during the 100 Hour Inspection Service that will be scheduled and performed by your Tigercat dealer. Refer to NEW MACHINE MAINTENANCE in THIS SECTION.

Contact your Tigercat Dealer Parts Department to order Kits.

FOLLOW-UP SAMPLES All follow-up samples must be taken as indicated in the chart above and will be the responsibility of the machine owner.

Copies of all oil analysis results must be forwarded to the Tigercat Warranty Department for continued warranty coverage. If samples are taken using the Tigercat Oil Analysis Program, a copy of all results will automatically be sent to Tigercat.

Tigercat Oil Analysis Kits are available from your Tigercat dealer parts department. If required, arrangements can also be made with your Tigercat dealer to supply and perform all of the required follow-up oil samples.

Refer also to OIL SAMPLE COLLECTION PROCEDURES in THIS SECTION for sample valve and drain plug locations.

200 Series Location

First Sample

Follow-up Samples

Hydraulic Oil

125 hrs

Every 1000 hrs or 6 Months

Swing Drive Gearbox

125 hrs

Every Oil Change (500 hours or 3 Months)

Track Drive Gearboxes (if applicable)

125 hrs

Every 1000 hrs or 6 Months

Transmission (if applicable)

125 Driving hrs

Every Oil Change (500 hours or 3 Months)

Front & Rear Axles (if applicable)

125 Driving hrs

Every Oil Change (1000 hours)

3.4

Tigercat T234B Track Loader

Lubrication and Maintenance

OIL SAMPLE COLLECTION PROCEDURES

Contact your Tigercat dealer to purchase additional or replacement hydraulic sample valves or drain plugs.

A

In cases where oil samples must be pumped or otherwise drawn out of a reservoir or housing, a hand operated oil suction pump is also available from your Tigercat dealer.

HYDRAULIC OIL SAMPLES:

B

• Hydraulic oil samples should be taken from the circulating oil flow at operating temperature, with no functions actuated, using sample valves that are permanently located on the machine whenever possible.

234E-200

Hydraulic Oil Return Manifold

A Filter restriction indicator B Oil sampling connector

• To obtain a representative oil sample, sample valves must be purged before the actual oil sample is taken. Drain a minimum of 90–120 mL (3–4 oz) of oil into a separate container and discard this oil using approved recycling methods.

Fill out the Sample Information Form (SIF) completely and accurately. When taking multiple oil samples, fill out all of the required SIF forms in their entirety, prior to taking any oil samples. Then, immediately package each completed SIF form together with the matching oil sample in the black outer shipping container as each individual sample is taken. This will reduce the possibility of mixing up or incorrectly identifying the SIF forms and oil samples. Incorrectly identified samples could result in a false alarm.

• Replace the dust cover on the sample valve immediately after taking the oil sample and sealing the sample bottle.

GEARBOX SAMPLES:

The accuracy of the lab analysis results is very dependent on the quality of the oil sample taken. Collection of clean oil samples that are representative of the main body of oil are essential if meaningful lab results are to be obtained.

• These samples can be taken during the oil change process.

Erroneous readings may result if proper collection, handling, packaging and shipping practices are not followed prior to the sample being tested by the lab. To be able to accurately compare and trend the lab results over time, all follow-up samples should be consistently taken from the same location using the same techniques as all previous samples.

• Place the required drain container under the machine to capture the used oil to be discarded using approved recycling methods.

• To obtain a representative oil sample, ensure the oil is warm and has not settled very long (within 30 minutes of shutdown).

• Remove the drain plug and allow approximately 50% of the oil to drain, then place the sample bottle in the stream of draining oil to obtain a representative sample.

TRANSMISSION AND AXLES SAMPLES:

• Ensure that all sample valves and drain plugs are clean and free of debris.

• These samples can be taken during the oil change process.

• Remove the sample bottle cap only when ready to take the sample. Keep the cap clean–do not put it in your pocket or let it get contaminated in any way.

• To obtain a representative oil sample, ensure the oil is warm and has not settled very long (within 30 minutes of shutdown).

• Do not allow any airborne dirt, etc. to enter the sample bottle.

• Place the required drain container under the machine to capture the used oil to be discarded using approved recycling methods.

• Avoid contamination of the sample–replace the sample bottle cap immediately after filling the bottle to approximately ¾ full. All samples taken should be immediately forwarded to the lab for processing.

• Remove the drain plug and allow approximately 50% of the oil to drain, then place the sample bottle in the stream of draining oil to obtain a representative sample.

3.5

Lubrication and Maintenance

Tigercat T234B Track Loader

GENERAL

• Inspect the EXHAUST SYSTEM DAILY for any signs of leakage. Check for worn, cracked, broken, or damaged pipes or muffler. Also check for missing or damaged bolts or clamps.

Should any exhaust leaks or defective parts be found, repairs must be made immediately.

Engine exhaust leaks can cause fires. DO NOT OPERATE the machine until the exhaust leak is repaired.

CAUTION All handles, steps and platforms must be kept free of grease, oil, fuel, mud, snow, ice and forest debris.

• Clean around filler caps before checking or adding fluids.

• During daily operation of the machine, the occurrence of exhaust leaks are usually accompanied by a change or increase in engine exhaust noise levels. These audible warnings cannot be ignored. Should any exhaust leaks occur during operation, the machine must be shut down immediately and not put back to work until the necessary repairs have been completed.

• Clean around hydraulic fittings before breaking connection. Plug or cap immediately.

• Clean up spills as soon as possible.

• Always use clean oil and containers.

• Drain dirty oil while still warm.

• Do not exceed recommended fluid levels.

• Always have a fire extinguisher at hand.

• Service all hydraulic filters after the failure of a pump, motor, cylinder or valve. Failures of this nature could contaminate the entire hydraulic system.

• For safety, always lower boom to the ground when leaving cab, leaving machine unattended or during service.

• Top up diesel fuel at each shift to reduce contamination by condensation.

• Clean up oil spills in engine enclosure immediately.

• Before welding on machine, be sure to disconnect all electrical connections and follow all servicing safety precautions as outlined in the WELDING, PRIOR TO of SECTION 1.

• When welding, secure ground connection as close to working position as possible to prevent arcing across machined surfaces or through bearings.

• Clean away all branches, bark and chips.

Clean up all traces of oil to avoid fires.

*OIL LOST FROM LEAKAGE LOST OIL (LITRES) LEAKAGE RATE

PER DAY

LOST OIL (US GALLONS)

PER MONTH PER YEAR

PER DAY

PER MONTH PER YEAR

One drop In TEN Seconds

0.424

12.72

152.0

0.112

3.36

40.0

One drop In FIVE Seconds

0.852

25.6

306.6

0.225

6.75

81.0

One drop per second

4.26

127.76

1533.1

1.125

33.75

405.0

Three Drops per Second

14.2

425.86

5110.31

3.75

112.5

1350.0

Drops Break Into Stream

90.83

2725.5

32706.0

24.0

720.0

8640.0

3.6

Tigercat T234B Track Loader

Lubrication and Maintenance

CHECK EMERGENCY EXIT, MONTHLY:

FIRE PREVENTION

An alternate exit route is provided: the right side window can be used as an emergency exit. This exit is only to be used if the side door cannot be opened.

Maintaining your machine properly will greatly extend its life and reduce your operating costs.

Fire can result in a machine loss which can be financially devastating.

IMPORTANT! After transporting (trucking) a machine from one job sight to the next, open all doors and access panels and blow off any debris that could have repositioned itself onto the engine and exhaust parts due to wind turbulence caused by the journey.

234T-031

1. Pine needles and bark when allowed to accumulate, form a fuel source that when ignited is extremely difficult to extinguish. A thorough program of regular cleaning and washing will reduce the possibility of a fire starting. In the event a fire does start, the regular cleaning program will improve the chances of successfully extinguishing a fire.

Sliding Window Handle

Open the right side window by lifting the latch handle and slide the window open.

B

A

2. Pay close attention to wiring and hose routing during maintenance. All wiring harnesses and hydraulic hoses must be properly restrained and clamped to prevent damage from chaffing.

3. If equipped, read the fire suppression system manual and have the system serviced regularly by qualified personnel.

4. In case of fire, lower the boom system to the ground and turn OFF the engine before discharging the fire suppression system.

234T-046 234T-047

Right Side Window Screen Knob

Also refer to FIRE PREVENTION in SECTION 1 for additional information.

A Outside Cab B Inside Cab

On machines equipped with window screens, there are two hand knobs, one on the inside the cab and one on the outside of the cab, that can be removed to open the window screen. Only one hand knob has to be removed to open the window screen as follows: FROM INSIDE THE CAB Open the cab window and turn the inside hand knob counterclockwise to remove the hand knob and open the window screen. Push the window screen out to open it. Exit the cab if you can safely do so.

FROM OUTSIDE THE CAB The window screen can also be opened from the outside by unscrewing the hand knob counterclockwise on the outside and remove it.

When the hand knob is removed the screen can be swung open.

It is therefore essential that this exit be inspected monthly to ensure it is operational.

3.7

Lubrication and Maintenance

Tigercat T234B Track Loader

SCHEDULED MAINTENANCE

*Lubricating cylinder pins and boom joints: 1. Machine must be on level ground.

EVERY 8 HOURS

2. Fully extend stick boom cylinder.

PERFORM • Drain fuel/water separator.

• Conduct an overall visual inspection.

CHECK

234B-045

• Engine coolant level.

3. Lower main boom and rest grapple firmly on ground or stable trailer.

• Engine oil level.

• Hydraulic oil level.

4. While in this position lubricate all cylinder retaining pins and boom joints.

• Swing gearbox oil level.

NOTE: This procedure will allow grease to flow to the normally loaded side of the pin/ bearing surfaces.

• Fill reservoir to halfway mark.

• Air intake precleaner.

• Air cleaner unloader valve.

• Grapple yoke pins: 2-fittings–purge.

• Air intake filter restriction indicator.

• Grapple rotate pinion: 1-fitting–4 shots, rotate 90° after each shot.

Replace primary filter if indicator is in red zone.

Replace secondary (safety) filter every third primary filter change to guarantee maximum performance and reliability.

• For leakage around hydraulic components and flexible hoses.

• For loose nuts, bolts and fittings.

• Grapple arm pins: 6-fittings–purge.

• Grapple cylinder pins: 4-fittings–purge.

Refer to engine MANUFACTURERS' OPERATION AND MAINTENANCE MANUAL and ATTACHMENT MANUAL for additional required maintenance at this scheduled time period.

• Condition and tension of fan belts.

• All engine air intake system components (including charge air cooler) rubber elbows, connector hoses, tubes and clamps for damage, hardening, wear, cracks, leaks, loose clamps or loose hanger bracket hardware and repair or replace immediately.

CLEAN • Oil cooler, engine radiator, A/C condenser and charge air cooler.

• Remove potentially damaging limbs or sticks and all debris.

LUBRICATE:

EVERY 24 HOURS PERFORM • 8 HOURS Maintenance.

LUBRICATE • Lubricate grapple rotate bearing: 1-fitting–4 shots, rotate 90° after each shot.

Refer to engine MANUFACTURERS' OPERATION AND MAINTENANCE MANUAL and ATTACHMENT MANUAL for additional required maintenance at this scheduled time period.

• Swing pinion: 1-fitting–10 shots while swinging.

• Swing bearing: 1-fitting–4 shots while swinging.

• Rotary manifold seal: 1 fitting–1 shot while swinging.

• Boom joints: 4-fittings–purge*.

• Cylinders; boom, stick & tilt: 4-fittings total– purge*.

3.8

Tigercat T234B Track Loader

Lubrication and Maintenance

EVERY 125 HOURS

EVERY 250 HOURS

PERFORM

PERFORM

• 8 HOURS Maintenance.

• 8 HOURS Maintenance.

• 24 HOURS Maintenance.

• 24 HOURS Maintenance.

• 125 HOURS Maintenance.

CHECK • Return filters restriction indicator with engine running at high idle and oil flow.

CHECK

• Fluid level in batteries unless maintenance free.

LUBRICATE

• Fire extinguisher and turn it to mix contents.

• Swing gearbox lower bearing: 2-fittings–5 shots each *

• Engine rpm.

• All hydraulic pressures.

* With gearbox at operating temperature slowly add 5 shots of lithium based EP2 grease to each side of the gearbox.

• Hydraulic pumps and motor securing bolts.

• Torque tightening points as per new machine maintenance.

NOTE: Do not use a power grease gun.

NOTE: During cold weather applications the swing function must operate for several hours to achieve operating temperature.

CHECK FOR DAMAGE TO • Main and stick booms and cylinders.

• Tracks, track frames and carbody.

IMPORTANT! Do not force grease, gearbox failure may result. Do not use winter grease. Grease should purge from gearbox pinion seal.

• Swing bearing area.

• Attachment.

REPLACE

• Make repairs immediately.

• Engine fuel filter **

CLEAN/REPLACE • Air conditioner re-circulation filter **

• Fuel/water separator filter **

• Cab fresh air filter **

• Engine oil and filter ** • DEF Dosing Module Filter ** (Tier 4f machines only).

VISUALLY INSPECT FOR • Frayed electrical wiring and hydraulic hoses.

Refer to engine MANUFACTURERS' OPERATION AND MAINTENANCE MANUAL and ATTACHMENT MANUAL for additional required maintenance at this scheduled time period.

• Wear in any other components.

Refer to engine MANUFACTURERS' OPERATION AND MAINTENANCE MANUAL and ATTACHMENT MANUAL for additional required maintenance at this scheduled time period.

** Use of filters other than genuine Tigercat replacement filters is not recommended.

3.9

Lubrication and Maintenance

Tigercat T234B Track Loader

EVERY 500 HOURS

EVERY 1000 HOURS

PERFORM

PERFORM

• 8 HOURS Maintenance.

• 8 HOURS Maintenance.

• 24 HOURS Maintenance.

• 24 HOURS Maintenance.

• 125 HOURS Maintenance.

• 125 HOURS Maintenance.

• 250 HOURS Maintenance.

• 250 HOURS Maintenance.

LUBRICATE • Door and cover hinges: 10 fittings – 1 shot.

• 500 HOURS Maintenance.

CHECK • Fuel in tank strainer

CHECK • Torque on swing bearing and swing gearbox retaining bolts

DRAIN AND REFILL

• Torque on track drive gearboxes and motor mounting bolts

FILL

• Track rollers and idlers for oil leakage. These components are filled with oil and considered maintenance free. If oil leakage is detected repair of component(s) will be necessary.

REPLACE • Engine crankcase ventilation filter ** • Hydraulic Oil return filters ** • Hydraulic Oil pilot pressure filter **

• Track drive gearboxes.

• Track drive gearbox with both level plugs in line with the horizontal plane and above center.

REPLACE • Air cleaner unloader valve.

Refer to engine MANUFACTURERS' OPERATION AND MAINTENANCE MANUAL and ATTACHMENT MANUAL for additional required maintenance at this scheduled time period.

• Swing pump charge pressure filter ** • Oil in swing gearbox – Fill reservoir to halfway mark.

Refer to engine MANUFACTURERS' OPERATION AND MAINTENANCE MANUAL and ATTACHMENT MANUAL for additional required maintenance at this scheduled time period.

** Use of filters other than genuine Tigercat replacement filters is not recommended.

3.10

Tigercat T234B Track Loader

Lubrication and Maintenance

EVERY 2000 HOURS PERFORM • 8 HOURS Maintenance.

• 24 HOURS Maintenance.

• 125 HOURS Maintenance.

• 250 HOURS Maintenance.

• 500 HOURS Maintenance.

• 1000 HOURS maintenance.

DRAIN AND REFILL • Hydraulic oil tank with recommended hydraulic oil. Refer to APPROVED HYDRAULIC OILS in THIS SECTION.

REPLACE • All air intake rubber components such as elbows and connectors – High temperatures in this area can cause the rubber to harden.

NOTE: High-temperature silicone connectors do not need to be replaced unless they are damaged.

NOTE: Refer to AIR INTAKE MAINTENANCE in THIS SECTION. Refer to engine MANUFACTURERS' OPERATION AND MAINTENANCE MANUAL and ATTACHMENT MANUAL for additional required maintenance at this scheduled time period.

3.11

Lubrication and Maintenance

Tigercat T234B Track Loader

LUBRICATION AND SERVICE POINTS

3.12

Tigercat T234B Track Loader

Lubrication and Maintenance

3.13

Lubrication and Maintenance

Tigercat T234B Track Loader

APPROVED HYDRAULIC OILS Use one of the following oils to fill or replenish the hydraulic system.

3.14

Tigercat T234B Track Loader SWING DRIVE LUBRICATION LUBRICATION OF SWING DRIVE GEARBOX LOWER BEARINGS

Lubrication and Maintenance LUBRICATION OF SWING DRIVE GEARBOX UPPER GEARING 234B-355

The cavity in the lower portion of the gearbox where the two lower bearings are housed is completely filled with grease.

HALF FILL RESERVOIR WITH RECOMMENDED OIL.

234B-352

LOWER BEARING GREASE FITTINGS

CONNECTING HOSE TO GEARBOX

SWING DRIVE GEARBOX OIL RESERVOIR The swing gearbox upper gearing is filled with gear oil. Check oil level in the bottle every 8 hours.

The oil reservoir is located on the side of the swing drive gearbox enclosure. Oil level in the bottle must be kept at the half full mark at all times. Drain and replace swing drive gearbox upper bearing gear oil every 500 hours. Use 75W-90 or 80W-140 gear oil.

SWING DRIVE GEARBOX ENCLOSURE Open the swing drive gearbox enclosure and locate the grease fittings. Using a hand grease gun and with the gearbox at operating temperature slowly add 5 shots of lithium based ep2 grease to each side of gearbox every 250 hours. DO NOT OVERGREASE.

For additional information refer to SECTION 15 of the SERVICE MANUAL. LUBRICATION OF SWING PINION AND SWING BEARING SWING BEARING GREASE FITTING

NOTE: During cold weather applications the swing function must operate for several hours to achieve operating temperature. If machine is not warmed up, the lower seal can be damaged.

IMPORTANT! Do not force grease, gearbox failure may result.

Do Not use a power grease gun to lubricate this machine. Use a hand grease gun only.

For additional information refer to SECTION 15 of the SERVICE MANUAL.

SWING PINION GREASE FITTING

T234B-015

FOOT PEDALS

To lubricate the swing bearing, apply 4 shots of grease while swinging every 8 hours to the right grease fitting located by the swing foot pedal in the operator's cab. To lubricate the swing pinion (or teeth) apply 20 shots grease every 8 hours while swinging to the left grease fitting located by the swing foot pedal. The grease fittings are clearly labelled.

For lubrication schedule, refer to SCHEDULED MAINTENANCE in THIS SECTION. For additional information refer to SECTION 15 of the SERVICE MANUAL. 3.15

Lubrication and Maintenance

Tigercat T234B Track Loader

ROTARY MANIFOLD LUBRICATION

ROTARY MANIFOLD GREASE FITTING

T234B-015

FOOT PEDALS

LUBRICATION OF ROTARY MANIFOLD To lubricate the rotary manifold, apply 1 shot of grease while swinging every 8 hours to the top grease fitting located by the swing foot pedal in the operator's cab. The grease fittings are clearly labelled.

For lubrication schedule, refer to SCHEDULED MAINTENANCE in THIS SECTION. NOTE: This fitting may be plugged depending on the type of rotary manifold.

3.16

Tigercat T234B Track Loader

Lubrication and Maintenance

HYDRAULIC OIL TANK

HYDRAULIC OIL SIGHT GAUGE/ SENDER

234B-107

HYDRAULIC TANK

SIGHT GAUGE

HYDRAULIC OIL FILTERS HYDRAULIC PUMPS

LOW LEVEL SENDING UNIT

234E-282

HYDRAULIC OIL SIGHT GAUGE/SENDER A sight gauge on the front of the tank is visible from the front access panel or the left hand side door. The hydraulic oil level must be kept between the HIGH and LOW limits at all times. A low level switch is incorporated into the level indicator.

When the hydraulic oil reaches this level the switch activates a critical alert warning on the MD3 display.

HYDRAULIC OIL TANK

Allowing the level to drop below the LOW limit can result in severe damage to hydraulic components.

If the oil level drops, inspect the machine including all fittings and hydraulic components for leaks.

Once the source of the oil loss is located and repaired, oil can be added to the tank.

234B-078

3.17

Lubrication and Maintenance

Tigercat T234B Track Loader

HYDRAULIC TANK VACUUM AIR VENT CHECK VALVE

SWITCH IN CAB VACUUM SWITCH 'OFF' POSITION

VACUUM SENSING SWITCH

VACUUM SWITCH 'ON' POSITION

AIR VENT BREATHER VACUUM PUMP

SOLENOID VALVE 234B-009

LEFT ARMREST

This switch will not function if the battery disconnect switch is turned off. With the ignition key switch in the OFF position and the key removed, push the vacuum switch to the ON position to activate the vacuum pump.

HYDRAULIC TANK

SWITCH IN ENGINE COMPARTMENT 234B-277

HYDRAULIC TANK VACUUM SYSTEM

The purpose of the vacuum pump system is to hold the hydraulic oil in the tank when servicing pumps and other hydraulic components, minimizing oil spill. When activated, a solenoid valve closes off the hydraulic tank breather air supply. The pump removes tank air to create a vacuum, which then holds the oil in the tank. This system eliminates the need to drain the hydraulic tank beforehand.

NOTE: When the ignition key is in the RUN position, the vacuum pump system will not start.

Alternatively if the vacuum pump is on, the engine cannot be started. The vacuum pump also will not start if the battery disconnect switch is in the OFF position.

Do not use the vacuum pump when changing hydraulic filters, instead use the Air Vent Valve to release pressure from the hydraulic tank. Using the vacuum pump system while changing filters creates the risk of introducing much more air into the hydraulic system.

It is OK to use the vacuum system when changing the case drain strainers.

VACUUM SWITCH 250D-004

FRONT ENGINE COMPARTMENT

This switch is "unswitched" and will function even with the battery disconnect switch in the off position. With the ignition key switch in the OFF position and the key removed, push the right hand side of the switch to put it in the ON position to activate the vacuum pump.

Activating the pump will create a vacuum condition (9 in.Hg) in the hydraulic tank. The vacuum pump will automatically start and stop as necessary to maintain the tank vacuum. The vacuum switch will also lock out the start solenoid to prevent the engine from being started.

Relieve the vacuum in the tank by placing the vacuum switch in the OFF position.

NOTE: The engine will not start until the tank vacuum has been relieved.

IMPORTANT! It is recommended that the start key be removed while servicing the hydraulic system.

Do not attempt to START the machine or turn key to the RUN position.

Do not leave machine unattended or overnight with vacuum pump on.

3.18

Tigercat T234B Track Loader

Lubrication and Maintenance

HYDRAULIC HAND FILL PUMP

OIL FILL SHUTOFF VALVE

HAND FILL PUMP T250D-009

HYDRAULIC HAND FILL PUMP

The hydraulic hand fill pump is used to add oil to the hydraulic tank. It is located inside the engine compartment near the front left corner and is made accessible by removing the front access panel.

Adding Oil Prior to adding oil to the tank, determine and repair the source of the oil loss. Remove hose clamp from end of suction hose, remove hose from stored position, thoroughly clean outside surface of suction hose and insert end into supply drum. Open the oil fill shut off valve (ball valve located on top of the hand pump). Operate the pump by moving the handle back and forth at medium speed and a steady motion. The oil passes through the filters on the return lines of the hydraulic system. When the sight gauge reads between LOW and HIGH cease pumping and return handle to upright position. Close the oil fill shut off valve.

NOTE: Turning on the hydraulic tank vacuum pump will assist the filling procedure.

3.19

Lubrication and Maintenance

Tigercat T234B Track Loader

HYDRAULIC OIL RETURN FILTERS

The "in" side of the filter heads are connected to a return manifold. There is also a filter restriction indicator and an oil sampling connector that are mounted onto the manifold. To check the condition of the filter elements; With the hydraulic oil at normal operating temperature, place engine throttle control to FULL and with machine saw cut function operating, the filter restriction indicator should be in the GREEN zone. If the pointer is in the RED zone replace all four filter elements.

RETURN MANIFOLD

Changing the filters:

ONE WATER ABSORBING (BLUE) RETURN FILTER

1. Ensure Loader is on level ground with stabilizers down. Lower grapple to ground and stop engine.

2. Wipe clean the area around the filter and head.

3 HYDRAULIC RETURN FILTERS

234E-282

3. Place rags below to catch the spillage of oil.

HYDRAULIC RETURN FILTERS

The majority of return oil entering the hydraulic tank passes through 4 spin-on hydraulic oil filters.

One of the filters is a water absorbing filter (color blue) which is in place to assist with the removal of unwanted moisture from the hydraulic oil (the filters are rated 10 micron absolute).

Each filter head has a bypass valve with a 1.7 bar (25 psi) cracking pressure so that oil can bypass the filters if they become restricted.Before this valve is activated, a 1.4 bar (20 psi) filter restriction pressure switch installed in the return manifold, will send a signal to the computer control system when an oil flow in excess of 1.4 bar (20 psi) is encountered at the return filters. This pressure switch closes and the hydraulic oil filter bypass icon displays RED on the MD3 computer and the master alarm will sound.

4. Wearing face protection (in case of an oil squirt), unscrew the old filter. Dispose of old filter and any oil properly.

5. The new Tigercat filter is supplied with two gaskets enclosed, examine the filter head closely to determine which gasket should be used and follow the instructions to ensure proper installation.

FILTER HEAD

GASKET

FILTR_SEALS 2

FILTER ELEMENT

SQUARE SECTION GASKET INSTALLATION

 Square Section Gasket Remove used gasket and clean groove in head.

Apply clean oil to new gasket surfaces.

Install new gasket into groove in filter head.

Screw on new filter until gasket makes contact.

Tighten filter an additional 3/4 turn.

DO NOT use bottom nut for filter installation or damage/leakage may result. Bottom nut is to assist in filter removal only.

234B-081

3.20

Tigercat T234B Track Loader

Lubrication and Maintenance FILTER HEAD

GASKET FILTER ELEMENT FILTR_SEALS 2

'O' RING GASKET INSTALLATION

 'O' Ring Gasket Remove used gasket and clean gasket seat in head.

Apply clean oil to new gasket surfaces.

Install new gasket on inside lip of filter.

Screw on new filter until gasket makes contact.

Tighten filter until top edge makes metal to metal contact with filter head.

(Approximately 1–1/2 additional turns after gasket contact.)

DO NOT use bottom nut for filter installation or damage/leakage may result. Bottom nut is to assist in filter removal only.

6. Start the engine and check for leaks.

3.21

Lubrication and Maintenance

Tigercat T234B Track Loader

PILOT PRESSURE FILTER

CASE DRAIN STRAINER

LOCATED UNDER LEFT SIDE OF ENGINE COMPARTMENT

234E-281

PILOT FILTER ELEMENT 234E-279

CASE DRAIN STRAINER

The case drain strainer is used to filter all case drain oil from the pumps and motors before it returns to the tank.

HYDRAULIC PILOT FILTER

A single element filter head filters all pilot oil prior to entering the pilot system. The filter head has a built-in bypass valve with a 50 psi cracking pressure so that oil can bypass the filter if the element becomes restricted.

The strainer element requires no regular maintenance over the life of the machine. This element requires maintenance only in the case of damage or contamination due to a hydraulic pump or motor failure.

The return filters and the pilot filter should be checked and replaced as per the maintenance schedule in SECTION 3.

IMPORTANT! Contaminated hydraulic fluid can lead to premature failure of hydraulic components and costly repairs.

Filters must be replaced at the recommended time intervals, See SECTION 3.

IMPORTANT! The strainer element is NOT a filter element.

Always use the correct replacement element. Use of an incorrect (filter type) element will result in pump damage.

RETURN DIFFUSERS/STRAINERS

Use of hydraulic oil filters other than the Tigercat brand could lead to severe wear and rapid failure of hydraulic system components.

DIFFUSER/ STRAINERS

234B-003

HYDRAULIC TANK

There are two reusable diffuser/strainers fitted to the return tubes inside the tank. The diffuser/ strainers should be inspected whenever the hydraulic tank is drained. See SERVICE AND LUBRICATION CHART in THIS SECTION.

3.22

Tigercat T234B Track Loader

Lubrication and Maintenance

SWING PUMP CHARGE PRESSURE FILTER CHARGE PUMP FILTER PRESSURE SWITCH

CHARGE PUMP FILTER

T250D-114 250CT-013

CHARGE PUMP FILTER

The swing pump charge pressure filter is a full flow filter mounted on a filter head with built-in bypass preset at 50psi. There is also a pressure switch installled into the filter head whiich will be activated at 50 psi and will send a signal to the computer control system. When the switch is activated the alarm will sound and the MD3 will display an alert warning. The filter is located in the output side of the charge pump.

For service and replacement intervals see SERVICE AND LUBRICATION CHART in THIS SECTION.

234B-084

Changing the filter or strainer: 1. Ensure Loader is on level ground with stabilizers down. Lower grapple to ground and stop engine.

2. Wipe clean the area around the filter and head.

3. Place rags below to catch the spillage of oil.

4. Wearing face protection (in case of an oil squirt), unscrew the old filter. Dispose of old filter and any oil properly.

5. Check the seating area for the gasket on the filter head and wipe it clean.

6. The new filter has an attached gasket, apply hydraulic oil to the gasket surface.

7. Screw on the new filter until the gasket makes contact with the seat in the filter head.

8. Turn filter an additional 1/2 turn by hand to tighten.

DO NOT use bottom nut for filter installation or damage/leakage may result. Bottom nut is to assist in filter removal only.

9. Start the engine and check for leaks.

IMPORTANT! Contaminated hydraulic fluid can lead to premature failure of hydraulic components and costly repairs.

Filters must be replaced at the recommended time intervals, Refer to SCHEDULED MAINTENANCE in THIS SECTION. Use of hydraulic oil filters other than the Tigercat brand could lead to severe wear and rapid failure of hydraulic system components.

3.23

Lubrication and Maintenance

Tigercat T234B Track Loader

FUEL TANK AND FILLER

REFUELING

The tank is located underneath the cab and has a capacity of 100 US gallons. The fuel filler is located on the front of the machine below the cab.

Park machine on level ground, shut off engine and allow machine to cool.

D

FILLER TUBE

DO NOT refuel while smoking or near an open flame or sparks.

Clear obstructions from steps and handles needed to access fuel tank.

Open cover on top of fuel tank (if equipped) and clear any debris from around the fill cap.

T234B-020

Remove filler cap slowly to allow pressure to escape from tank.

FUEL TANK AND FILLER

To add fuel to the tank place the fill nozzle in the inner fill tube, air from the tank will vent out via the air vent passage.

Inspect fill cap gasket.

Inspect fuel strainer located under the fill cap for debris or damage.

AIR VENT PASSAGE

Attach a grounding strap to an unpainted metal surface on the machine if the refueling tank or nozzle is so equipped.

INNER FILL TUBE

Fill tank until fuel level reaches the strainer or the full mark on the sight gauge if equipped. Do not leave nozzle unattended or spillage may occur.

Remove nozzle and ground strap (if applicable), then install fill cap hand tight before closing fill cap cover.

Before restarting the machine, check that no other personnel have moved into the hazardous area and sound the horn.

248-20

FUEL FILL TUBE

S≤15 mg/kg ULTRA LOW SULFUR FUEL ONLY 36686AUNI R0

3.24

Tigercat T234B Track Loader

Lubrication and Maintenance

ENGINE FILTERS - REMOVE AND REPLACE

WARNING

This machine is equipped with two fuel filters.

One fuel filter comes with and is mounted on the engine. The other remote mounted fuel filter is a combination unit, with a replaceable fuel filter with drain valve and a reusable water in fuel sensor. For service and replacement intervals see SERVICE AND LUBRICATION POINTS in THIS SECTION. Refer also to engine manufacturer's manual for more detailed information.

T234B-013

VENT PLUG

The fuel pump high-pressure fuel lines and fuel rail contain very high pressure fuel.

Never loosen any fittings while the engine is running. Personal injury and property damage can result.

ENGINE FUEL FILTER AND REMOTE FUEL FILTER/WATER SEPARATOR Changing the primary fuel filter: 1. Park machine on level ground, lower stabilizers and grapple to the ground, stop engine.

HAND PRIMER

2. Wipe clean the area around the filter and head.

3. Place rags below to catch the spillage of fuel.

4. Wearing face protection (in case of a fuel spray) unscrew the old filter. Dispose of any fuel and the fuel filter properly.

FUEL FILTER/ WATER SEPARATOR

5. Check the seating area for the o-ring on the filter head and wipe clean.

6. Lubricate the o-ring on top of the new filter with clean engine oil. DO NOT pre-fill the new filter.

ENGINE FUEL FILTER

ENGINE FUEL FILTER AND FUEL FILTER/ WATER SEPARATOR

7. Screw the new filter onto the filter head as specified by the filter manufacturer. Note: Mechanical over tightening can damage the filter element.

IMPORTANT !

Failure to service and replace filters at the proper intervals specified in the manufacturer's manuals, could cause damage to the machine and result in the product warranty becoming NULL and VOID. Check Tigercat parts catalog for replacement filters.

8. Prime the fuel system using the hand primer on the remote fuel filter/water separator before starting the engine.

Loosen the plug on the top of the remote fuel filter/water separator. Pump the hand primer until fuel begins to seep out around the loosened plug, continue to pump until no air bubbles are visible (approximately 30 pumps).

Tighten the plug. Pump the hand primer 30 more times.

IMPORTANT !

Filters that are an integral part of the engine (fuel and lubricating oil) should be serviced and replaced according to the engine manufacturer's manual.

Tier III and IV engines typically use filters with a very fine micron rating. If the fuel supply is dirty, the fuel filter must be replaced more frequently than recommended in the owner’s manual. Operating the machine with a clogged fuel filter will result in low engine power. It is also recommended that the fuel/water separator bowl be drained daily.

9. Start the engine and check for leaks. Refer to STARTING ENGINE in SECTION 2.

When installing a new fuel filter, DO NOT pre-fill with diesel fuel, engine fuel pump damage may result. This type of failure is not warrantable by the engine manufacturer.

To prolong the operating life of the fuel filter, ensure that the fuel supply storage tank is clean and free of water and that the fuel is pre-filtered prior to adding it to the machine.

3.25

WARNING

Drain fuel filter into a container and dispose of all fluids properly.

Lubrication and Maintenance

Tigercat T234B Track Loader

REMOTE FUEL FILTER/WATER SEPARATOR HAND PRIMER VENT PLUG

FILTER REMOVAL TOOL

FUEL SEPARATOR BOWL

234B-340

FILTER REMOVAL TOOL

4. Loosen the metal vent plug on the filter head.

5. Turn the drain valve open on the separator bowl to allow the fuel to drain completely from the separator bowl into a suitable container.

6. Close the drain valve.

DRAIN TAP

7. Disconnect the water in fuel sensor and heater element from the wiring harness.

FUEL FILTER / WATER SEPARATOR Changing the remote fuel filter/water separator: 1. Park machine on level ground, lower stabilizers and grapple to the ground, turn off the engine.

2. Wipe clean the area around the filter and head.

3. Place a suitable container under the filter and/ or place rags below to catch the spillage of fuel.

O-RING

SEPARATOR BOWL

FUEL FILTER

HAND PRIMER PUMP VENT PLUG

8. Wearing face protection (in case of a fuel spray) unscrew the separator bowl from the head using the filter removal tool. The filter removal tool is located in the tool compartment at the front of the upper frame. Dispose of any fuel properly .

9. Remove and discard the O-ring from the top of the separator bowl.

10. Clean the separator bowl.

11. Remove the filter cartridge from the filter head (pressure fit) and discard properly.

12. Place the new filter into position on the filter head.

13. Lubricate the o-ring with clean engine oil and install at the top of the separator bowl.

FILTER HEAD DRAIN KNOB WITH HOSE BARB 822D-025

HARNESS, HEATER (ELEMENT NOT SHOWN) SENSOR, WATER IN FUEL

14. Install (screw) separator bowl onto the filter head, hand tight, then turn an additional 3/4 turn only.

15. Connect water in fuel sensor and heater element to the wiring harness.

FUEL FILTER/WATER SEPARATOR COMPONENTS

3.26

Tigercat T234B Track Loader

Lubrication and Maintenance

16. Turn the ignition key to the ON position to energize the fuel supply shut-off valve.

17. Prime the fuel system using the hand primer until fuel spills out the metal vent plug.

18. Close the vent plug.

19. Start the engine and check for leaks. Refer to STARTING ENGINE in SECTION 2.

WARNING

Drain fuel filter into a container and dispose of all fluids properly.

ENGINE OIL FILTER

ENGINE OIL FILTER

234B-356

REAR OF MACHINE

Refer to the appropriate engine manufacturer's operation and maintenance manual for correct procedures and time intervals when servicing the engine oil filter.

3.27

Lubrication and Maintenance THE AFTERTREATMENT SYSTEM AND ITS RELATED COMPONENTS ARE APPLICABLE TO TIER 4F ENGINES ONLY.

DEF DOSING MODULE FILTER The DEF dosing module filter should be replaced as part of scheduled maintenance every 250 hours.

Tigercat T234B Track Loader REMOVE DEF DOSING MODULE FILTER 1. Park the machine on level ground with the attachment resting firmly on the ground. Refer to PARKING THE MACHINE in SECTION 1.

2. Make sure the engine is at operating temperature.

3. Turn OFF the engine.

4. Remove the ignition key.

If DEF and/or aftertreatment fault codes have occurred then Tigercat recommends performing a DEF flushing test and Urea Dosing System Test (UDST) at every DEF dosing module filter change to ensure proper operation of the DEF supply module.

5. Wipe clean the area around the DEF supply module and filter including the supply module ports with particular attention to the inlet port and filter cap to avoid introducing contamination into the filter housing while performing this procedure.

If no DEF and/or aftertreatment fault codes have occurred then only the DEF dosing module filter replacement is required.

6. Place container below to catch the spills.

CHANGING DEF DOSING MODULE FILTER, DEF FLUSHING TEST AND UDST (UREA DOSING SYSTEM TEST) TOOLS REQUIRED • 27 mm (1 1/16 in) wrench • Container to catch DEF and flushing water • Clean distilled/demineralized water • 1 litre (0.25 US gal) plastic water bottle with hose attached* • Laptop computer with Tigercat by FPT E.A.SY. software to run UDST test*

630E-281

7. Turn the filter cover counterclockwise to remove from the supply module. Use a 27 mm (1 1/16 in) wrench.

• PT-Box* IMPORTANT! Do not contaminate the DEF when performing maintenance on the system as this may cause costly damage to SCR system components and affect the proper operation of the aftertreatment system and the engine. *Items required if performing a DEF flushing test and UDST.

630E-282

8. Remove the equalizing element and note the colour of the filter inside (black or grey).

3.28

Tigercat T234B Track Loader

Lubrication and Maintenance

630E-285

9. Find the filter removal tool provided with the replacement parts select the correct edge BLACK (B) for black filters or GREY (G) for grey filters.

630E-287

12. Clean surfaces with distilled/demineralized water only to avoid DEF contamination.

Check the area around the filter for cracks. If cracks are found the supply module must be replaced.

13. Thoroughly clean the filter cover to avoid introducing contamination.

DEF FLUSHING TEST A 630E-284

10. Insert the tool edge completely until a click is felt or heard.

630E-333 630E-286

11. Pull out the filter, using a tool in the slot on the filter removal tool if required.

A

Inlet Port

1. Disconnect the DEF hose from the inlet port of DEF supply module.

2.

3.29

Fill the plastic bottle with distilled/ demineralized water.

Lubrication and Maintenance

Tigercat T234B Track Loader Manual for UDST test information.

A

630E-332

A

Inlet Port

3.

Connect the water bottle hose to the inlet port of the DEF supply module.

630E-331

7.

Distilled water will be drawn from the bottle and flushed through the DEF supply module.

Suction may begin to collapse the bottle and water flow out the bottom of the module will increase.

630E-328

8.

The results of the UDST will show a flat line for DEF pressure (red line) because the pump cannot build pressure without the filter in place.

9.

Repeat the UDST test a second time to ensure the DEF supply module is thoroughly flushed and working correctly.

630E-334

4.

Raise the water bottle above the DEF supply module.

5.

A small amount of water will flow through the DEF supply module and out the bottom where the filter has been removed.

6.

With the aid of an assistant run a UDST test from the laptop computer. Refer to PT Box

10. When the UDST flushing procedure has been performed twice successfully remove the bottle and hose.

11. Reinstall the DEF module inlet hose.

3.30

Tigercat T234B Track Loader REPLACE FILTER

Lubrication and Maintenance 4. Check that all personnel are clear of the machine before starting the engine.

5. Insert the ignition key and turn to the RUN position.

6. Sound horn to warn personnel of machine start-up.

7. Start the engine.

8. Check for leaks.

9. Turn OFF the engine.

630E-288

1. Install the new filter. Lubricate the o-rings on the filter with clean DEF solution for easy installation.

IMPORTANT! Do not contaminate the DEF when performing maintenance on the system as this may cause costly damage to SCR system components and affect the proper operation of the aftertreatment system and the engine.

WARNING Use only diesel exhaust fluid (DEF) which meets ISO 22241 specifications. NEVER fill the DEF tank with any other fluid.

DEF is injected into the exhaust gas stream during normal operation of the Selective Catalytic Reduction (SCR) aftertreatment system.

Use of other fluids may cause component damage, or a fire risk which could result in death or serious injury.

630E-289

2. Install the new equalizing element.

NOTE: The equalizing element must be replaced with each filter change.

630E-290

3. Reinstall the clean filter cover, tighten to 20 Nm (15 lbf-ft). Use a 27 mm (1 1⁄16 in) wrench.

3.31

Lubrication and Maintenance

Tigercat T234B Track Loader

UDST (UREA DOSING SYSTEM TEST) 1.

With the aid of an assistant run a UDST test from the laptop computer. Refer to PT Box Manual for UDST test information.

630E-327

2.

If the DEF supply module is functioning correctly the test should show a characteristic curve as shown above, DEF pressure (red line).

3.

A confirmation screen will indicate System is OK if the DEF supply module is functioning correctly.

4.

Repeat the UDST test a second time to confirm results.

630E-330

5.

If the UDST test passes twice the DEF supply module is OK.

630E-329

6.

If the UDST test fails twice note the error mode(s) and contact customer service.

3.32

Tigercat T234B Track Loader

Lubrication and Maintenance

DRAINING THE DEF TANK

9. Inspect the inlet strainer at the bottom of the DEF sending unit. Remove the strainer and back flush to clean. Clean or replace as necessary.

DEF TANK FILL CAP

41581AUNI R0

INLET STRAINER

DEF TANK COMPARTMENT T250D-120 The DEF tank is located inside the compartment on the left-hand front corner of the machine.

It is necessary to remove the DEF tank compartment to drain the DEF completely and clean out any contaminants. This is recommended in the case of DEF quality concerns and/or known contamination.

1. Use the DEF level indicator on the computer display to estimate the container capacity required to properly drain the DEF solution.

Refer to DIESEL EXHAUST FLUID (DEF) TANK in SECTION 2 for tank capacity.

2. Using the appropriate equipment syphon as much DEF from the tank to enable removal.

3. Disconnect the DEF quality sensor at the bottom of the tank and remove the DEF lines and connectors from the DEF sending unit at the top of the tank.

T250D-122

DEF SENDING UNIT

10. Reinstall the DEF sending unit to tank and refit tank to the compartment.

11. Reinstall the DEF tank compartment and deck plate.

12. Reconnect all hoses and connectors. Refill the washer bottle and gearbox oil reservoir.

13. Re-fill tank with new DEF only. Do not re-use the DEF. 14. Check for leaks and if any DEF has spilled, rinse well with water.

NOTE: To avoid contamination, always use clean DEF.

NOTE: DEF is corrosive to most metals.

Take care to protect the electrical connections once the DEF quality sensor has been disconnected.

4. Drain the washer bottle and gearbox oil reservoir and remove the hoses and connectors.

5. Remove the deck plate and remove the bolts securing the DEF tank compartment. Carefully remove the DEF tank compartment with tank.

6. Remove the DEF tank from the compartment.

7. Using a strap wrench carefully remove the DEF sending unit from the tank 8. Clean the inside of the tank with DEF or distilled/demineralized water only if required.

Thoroughly drain the tank after cleaning.

Diesel exhaust fluid (DEF) is an aqueous urea solution with 32.5% high purity urea and 67.5% deionized water. Note that DEF may also be referred to as AUS32 or AdBlue. All DEF must be American Petrolium Institute (API) Certified DEF or meet ISO 22241 specifications.

IMPORTANT! It is important to avoid contamination of DEF when performing maintenance on the system as this may cause costly damage to SCR system components and affect the proper operation of the aftertreatment system and the engine.

3.33

Lubrication and Maintenance

Tigercat T234B Track Loader

AIR CLEANER

AIR CLEANER UNLOADER VALVE This rubber valve on the tube of the air cleaner housing should be checked at the beginning of every shift. (8 hours) If this valve is missing, damaged or has become hard, it will cause the air cleaner to become ineffective. The unloader valve should be replaced every 1000 hours.

AIR CLEANER

AIR FILTER RESTRICTION INDICATOR AIR CLEANER UNLOADER VALVE 234B-353

AIR CLEANER

The air cleaner on this machine uses 2 filter elements, a primary element and a safety element.

To ensure maximum engine protection, it is important that the elements be serviced correctly and at proper servicing intervals.

AIR FILTER RESTRICTION INDICATOR A filter restriction indicator is located in the engine enclosure beside the air cleaner. The indicator is remote mounted and is connected to the outlet side of the air filter with a 1/4" diameter hose. Replace the primary air filter when the restriction indicator shows RED. This indicator provides a continuous reading whether the engine is running or is shut down. After replacing the filter, reset the indicator by pressing the reset button.

NOTE: Replace the safety element every third primary filter change.

The machine is also equipped with an engine air filter restriction sensor which sends a signal to the computer control system in the event of filter restriction. The engine air intake pressure icon turns YELLOW when service to the filter is required and turns RED, along with an ALERT message, when service to the air filter has reached a critical state.

234B-0082

Remove the unloader valve from the tube of the air cleaner housing.

Check and clean the valve. A good valve should be soft and flexible. If it is plugged, then check the filter elements, they may need replacing. Re-attach the valve to the tube.

The valve should suck closed at about 1/3 of full throttle.

When operating in high dust conditions this valve should be checked and squeezed every 2 hours to release dust buildup.

3.34

Tigercat T234B Track Loader

Lubrication and Maintenance IMPORTANT STEPS TO FOLLOW WHEN CHANGING FILTER ELEMENTS

In addition to the LUBRICATION AND MAINTENANCE SCHEDULE, the following instructions should also be noted.

AIR INTAKE TUBING AND JOINTS AIR CLEANER

234B-106

PRECLEANER ELBOWS

SAFETY ELEMENT

INTAKE TUBING

PRIMARY ELEMENT

AIR INTAKE TUBING AND JOINTS Check all air intake system components, rubber elbows, connector hoses, tubes and clamps for damage, hardening, wear, cracks, leaks, loose clamps or loose hanger bracket hardware and repair or replace immediately.

Replace all air intake rubber components such as elbows and connectors every 2000 hours - High temperatures in this area can cause the rubber to harden.

NOTE: High-temperature silicone connectors do not need to be replaced unless they are damaged.

OVER SERVICING Filter elements increase in dust cleaning efficiency as dust builds up on the media. Looks can be deceiving. A filter that is dirty is actually more efficient than one that is clean. A filter with dust build up on the media reaches nearly 100% dust cleaning efficiency. Only when a filter is so clogged with dirt that air restriction goes beyond the engine manufacturer’s guidelines, should be replaced.

IMPROPER SERVICING Engine exposure to dust during servicing is the largest single factor contributing to engine damage due to dust. Abrasive dust can easily enter the intake system once the air cleaner element has been removed for replacement. The safety element reduces the risk, however it must also be replaced at every third primary element change.

726D-006PLT

AIR FILTER ELEMENTS

1. Release the cover latches gently to reduce the amount of dust dislodged.

2. Avoid dislodging dust from filter element(s) by gently pulling the element out of the housing.

3. Check your old filter sealing surfaces, This will help detect foreign material on the sealing surface that is causing leakage.

NOTE: Filter elements should never be cleaned and reused. Cleaning causes dust to bypass the filter and be deposited on the inner surface of the filter media. The dust is then drawn directly into the engine.

4. Always clean the inside of the housing.

5. Always clean the sealing surface before inserting a new filter element.

6. Inspect the new filter for damage.

7. Insert the new filter properly. Apply pressure to the filter frame not the pleated filter surface.

8. Check connections hoses and tubes for an air tight fit. Ensure that all clamps, bolts and connections are tight. Check rubber elbows for splits or wear points. Leaks in these locations send dust directly to the engine.

NOTE: Refer to diesel engine manufacturer's operation and maintenance manual for more details and additional required maintenance of the Air Cleaner or replacement of the air filter elements.

3.35

Lubrication and Maintenance

Tigercat T234B Track Loader

AIR PRECLEANER

OPERATION: 3

3 4

AIR CLEANER PRECLEANER HOUSING

2 1 T250D-033

5

AIR CLEANER PRECLEANER

The engine air precleaner cleans engine air before it reaches the air cleaner filter elements. It removes contaminants such as dust, powder, insects, rain, and snow. The air precleaner should be checked every 8 hours to make sure that foreign materials have not plugged the intake area or the discharge louver area. Clean as required.

IMPORTANT! The air precleaner must be checked every 8 hours and cleaned as required.

If the inlet/precleaner is plugged causing a restriction to airflow, reduced engine performance and increased fuel consumption may result.

If a plugged inlet/precleaner is left too long, excessive air intake restriction may damage the rubber air intake tube. A damaged air intake tube will lead to ingestion of dirt into the engine which may result in engine failure.

480-017

PRECLEANER OPERATION

1. Air enters the precleaner.

2. Specially designed vanes move dirty air toward the impeller.

3. The spinning impeller spins the air creating centrifugal force to separate contaminants from the clean air.

4. Contaminants are blown out the discharge louver.

5. Clean air enters the intake to the air cleaner.

Note that the air filter restriction indicator may not function properly if the air intake tube is damaged.

Engine failures due to improper maintenance are not covered by Tigercat or Engine Manufacturer’s Warranty and any such claim will be denied.

IMPORTANT! For peak engine performance and maximum fuel economy, please ensure that the air precleaner is regularly checked and cleaned as required. All intake air tubes and clamps should be thoroughly inspected on a regular basis and any damaged or missing components should be replaced immediately.

3.36

Tigercat T234B Track Loader

Lubrication and Maintenance

AFTERTREATMENT SYSTEM (DENOX 2.2 SYSTEM - TIER 4F)

The DOC/SCR aftertreatment system consists of the following components:

The engine on this machine is equipped with a combination Diesel Oxidation Catalyst (DOC) and high efficiency Selective Catalytic Reduction (SCR) aftertreatment system to limit the nitrogen oxide exhaust gas values (NOx) to meet Tier 4f emission standard requirements with low fuel consumption.

This process is electronically controlled by the DENOX 2.2 system.

• • • • • • •

The diesel oxdation catalyst (DOC) uses oxidation at high temperatures to convert carbon monoxide (CO), hydrocarbons (HC) and the soluble organic fraction (SOF) of diesel particulates into inert compounds, carbon dioxide (CO2) and water vapour (H2O). In addition the DOC converts nitrogen oxide (NO) into nitrogen dioxide (NO2).

Increased NO2 levels enhance the performance of the SCR catalyst at low temperatures and increase the effectiveness of the DOC/SCR aftertreatment system as a whole.

• • • • • • • • •

The high efficiency SCR process is based on a series of chemical reactions which involve the reaction of ammonia with the oxygen in the exhaust gas to reduce nitrogen oxides (NOx) in the exhaust gas by transforming it into inert compounds: free nitrogen (N2) and water vapour (H2O). In addtion the high efficiency catalytic converter includes a clean up catalyst (CUC) which reduces any excess ammonia (NH3) which may result from the SCR process.

• • • • • •

3.37

Inlet Humidity Sensor Diesel Exhaust Fluid (DEF) Tank DEF Tank Heater Unit Heated DEF Supply Lines Coolant Valve Coolant Lines DENOX 2.2 control system (incorported into the engine control unit ) Supply module Exhaust Flap Inlet NOx Sensor DOC Inlet Temperature Sensor Diesel Oxidation Catalyst (DOC) Dosing Module (DEF Injector) Mixer Tube SCR Inlet Temperature Sensor Catalytic Converter with Clean Up Catalyst (CUC) incorporated Outlet Temperature Sensor NH3 Sensor Outlet NOx Sensor NOx Sensor ECU (Inlet) NOx Sensor ECU (Outlet) NH3 Sensor ECU

Lubrication and Maintenance

Tigercat T234B Track Loader

NOx SENSOR ECU (INLET)

ENGINE ECU

DIESEL OXIDATION CATALYST (DOC)

HEATED DEF SUPPLY LINES

COOLANT VALVE SUPPLY MODULE

DEF QUALITY SENSOR

AFTERTREATMENT COMPONENTS

234B-105

DEF TANK

DEF HEATER UNIT

HUMIDITY SENSOR

NOx SENSOR ECU (INLET)

DOSING MODULE (DEF INJECTOR) NOx SENSOR ECU (OUTLET) NH3 SENSOR ECU

DIESEL OXIDATION CATALYST (DOC) COOLANT VALVE SCR INLET TEMPERATURE SENSOR

CATALYTIC CONVERTER (SCR,CUC)

234B-104

AFTERTREATMENT COMPONENTS 3.38

Tigercat T234B Track Loader

Lubrication and Maintenance DEF DOSING MODULE FILTER

HUMIDITY SENSOR AIR FILTER

SUPPLY MODULE

EXHAUST FLAP ENGINE ECU

HC

NOx SENSOR

NOx CO

DEF QUALITY SENSOR

ENGINE

NOx SENSOR

NH3 SENSOR

H 2O

N2

HEATER VALVE (CIRCULATING ENGINE COOLANT)

MIXER TUBE

SCR NH3

CO2 CATALYTIC CONVERTER

630E-276

DEF LEVEL SENSOR

DOC

TEMPERATURE SENSORS

CUC

HC - HYDROCARBONS NOx - NITROGEN OXIDES CO - CARBON MONOXIDE NH3 - AMMONIA N2 - FREE NITROGEN H2O - WATER CO2 - CARBON DIOXIDE

DEF TANK

DOSING MODULE

DOC/SCR AFTERTREATMENT SYSTEM

The DOC/SCR aftertreatment system is electronically managed by the DeNOX 2.2 system incorporated into the engine control unit (ECU).

The ECU calculates and adjusts the flow rate of the DEF solution into the system based on current engine speed, torque delivered, exhaust temperature, amount of nitrogen oxides and ammonia present.

The exhaust passes through the diesel DOC which uses oxidation at high temperatures to convert carbon monoxide (CO), hydrocarbons (HC) and the soluble organic fraction (SOF) of diesel particulates into inert compounds, carbon dioxide (CO2) and water vapour (H2O). It also converts nitrogen oxide (NO) into nitrogen dioxide (NO2) which enhances the performance of the SCR catalyst.

The supply module pump picks up the DEF solution from the tank and sends it under pressure to the dosing module (DEF injector) to be injected into the exhaust at the outlet of the DOC and pass through the mixer tube upstream of the catalytic converter.

The first phase of the SCR process takes place in the first part of the catalytic converter: high temperature exhaust gas evaporates the DEF solution instantly and, by hydrolysis, converts it into ammonia (2NH3) and carbon dioxide (CO2).

Evaporation of the solution lowers exhaust gas temperature, bringing it closer to the optimum temperature required by the process.

The exhaust fumes and ammonia at the proper reaction temperature, are introduced into the catalytic converter, where the second phase of the process takes place: by reacting with the oxygen in the exhaust gases the ammonia is converted into free nitrogen (N2) and water vapour (H2O).

Finally the high efficiency catalytic converter incorporates a clean up catalyst (CUC) which reduces any excess ammonia (NH3) which may result from the SCR process.

IMPORTANT !

Engine should not idle longer than 9 consecutive hours. Damage to the emission control system will result. When this machine idles for an extended period excess hydrocarbon buildup is created in the DOC/SCR aftertreatment system. Burn off of excess hydrocarbon at full load immediately after a long idle period will generate excess heat which will cause damage to emission control system components.

3.39

Lubrication and Maintenance

Tigercat T234B Track Loader Diesel exhaust fluid (DEF) is used by the Selective Catalytic Reduction (SCR) aftertreatment system to lower the concentration of nitrogen oxides from the diesel engine exhaust of this vehicle. DEF is an aqueous urea solution with 32.5% high purity urea and 67.5% deionized water. Note that DEF may also be referred to as AUS32 or AdBlue and should meet ISO 22241 specifications. Use only DEF meeting this standard.

DIESEL EXHAUST FLUID (DEF) TANK HEATER UNIT

DEF TANK

DEF QUALITY SENSOR

DEF TANK

630E-262

It is important to avoid contamination of DEF when filling the tank as this may cause costly damage to SCR system components and affect the proper operation of the SCR system and the engine.

WARNING

The DEF tank is located inside the compartment on the left hand front corner of the machine. A DEF level indicator is shown on the main menu of the computer display.

The DEF tank includes a fill location, a heater unit and DEF quality sensor. The heater unit incorporates a heater coil, heating system inlet/ outlet connections, DEF inlet/outlet connections, a breather, level sensor, strainer, temperature sensor and electrical connector.

COOLANT HEATER COIL

LEVEL SENSOR

TEMPERATURE SENSOR DEF INLET STRAINER 620E-082

HEATER UNIT

Use only diesel exhaust fluid (DEF) which meets ISO 22241 specifications. NEVER fill the DEF tank with any other fluid.

DEF is injected into the exhaust gas stream during normal operation of the Selective Catalytic Reduction (SCR) aftertreatment system.

Use of other fluids may cause component damage, or a fire risk which could result in death or serious injury.

IMPORTANT! DEF should be stored between -11°C (12°F) and 30°C (86°F) and out of direct sunlight to maximize shelf life and to avoid DEF quality problems caused by improper storage.

When DEF levels are low or a problem with DEF quality is detected information messages and warnings will be shown on the computer display. Note that extremely low DEF levels and/ or DEF quality problems may result in derating of engine performance to meet emission standard requirements. Action to correct these problems should be taken immediately to avoid affecting engine performance and damage to aftertreatment system components. Refer also to COMPUTER – MD3 MESSAGES in SECTION 2 or SECTION 6 of the SERVICE MANUAL. Refer to DRAINING DEF TANK in SECTION 3.

Refer to DEF TANK in SECTION 2.

DEF QUALITY SENSOR 3.40

Tigercat T234B Track Loader

Lubrication and Maintenance

HEATER VALVE / HEATED DEF SUPPLY LINES

Heating is switched OFF when: • DEF tank temperature >16°C (61°F) • Supply module temperature >10°C (50°F) • Ambient air temperature >-4°C (25°F)

CONNECTOR

Heating is switched ON when: • DEF tank temperature <15°C (59°F) • Supply module temperature: +8°C (46°F) • Ambient air temperature: -5°C (23°F)

COOLANT OUTLET

COOLANT BYPASS

COOLANT INLET 630E-265

When conditions require heating the system will thaw DEF within 30 minutes of engine start for proper operation of the aftertreatment system.

Note also that whenever the engine is stopped all DEF is pumped back to tank before the engine power system is turned off. This process takes approximately 90 seconds.

HEATER VALVE

The heater valve is mounted on the frame directly under the engine. Access it from underneath the rear of the machine.

HEATED DEF SUPPLY LINES The DEF supply lines are heated by an electrical wire element built into each hose. The electrical connector is at the Supply Module end of the line.

There are 3 heated lines and 2 types. There is 1 x 24V line and 2 x 12V lines.The lines can be identified by the electrical connector. The 24V line has a male connector and the 12V lines have female connectors.

DEF LINE

250D-051

HEATER VALVE

MALE ELECTRICAL CONNECTOR

The heater valve controls the flow of engine coolant through the DEF tank heater coil and the supply module when heating of the DEF is required. The heater valve also controls the constant flow of engine coolant to the dosing module for cooling purposes. This machine is equipped with electrically heated DEF supply lines.

T250D-117

24V HEATED DEF LINE DEF LINE

FEMALE ELECTRICAL CONNECTOR

IMPORTANT! If removing the heater valve care should be taken to reconnect the cooling hoses correctly.The heater valve is directional and if the hoses are connected incorrectly the DEF may overheat which will reduce its quality.

T250D-118

DEF freezes at -11°C (12°F).

Temperature sensors signals control the operation of both the electrically heated DEF supply lines and the heater valve which, depending on the temperature, opens or closes the flow of hot engine coolant to the heater coil and supply module.

12V HEATED DEF LINE

The 2 x 12V lines run from the Supply Module to the DEF Tank. These 2 lines are connected electrically in series, so if any one of these 2 lines fail the element in the other line would not function.

For full description of wiring REFER to SECTION 6 of the SERVICE MANUAL.

3.41

Lubrication and Maintenance

Tigercat T234B Track Loader DIESEL OXYDATION CATALYST (DOC)

SUPPLY MODULE

234B-084

DOC

DIESEL OXIDATION CATALYST (DOC) 250D-052

The diesel oxdation catalyst (DOC) uses oxidation at high temperatures to convert carbon monoxide (CO), hydrocarbons (HC) and the soluble organic fraction (SOF) of diesel particulates into inert compounds, carbon dioxide (CO2) and water vapour (H2O).

SUPPLY MODULE

The supply module is located on the frame under the engine. Access it from underneath the rear of the machine.

The supply module pump picks up the DEF solution from the tank and sends it under pressure to the dosing module, mounted on the mixer tube incorporated into the diesel oxidation catalyst.

DEF is injected into the exhaust at the outlet of the diesel oxidation catalyst and upstream of the catalytic converter.

In addition the DOC converts nitrogen oxide (NO) into nitrogen dioxide (NO2). Increased NO2 levels enhance the performance of the SCR catalyst at low temperatures and increase the effectiveness of the DOC/SCR aftertreatment system as a whole.

The DOC is located upstream of the catalytic converter (SCR & CUC) and at its outlet incorporates the mixer tube and the mounting for the dosing module.

DENOX 2.2 DOSING SYSTEM

EXHAUST FLAP

EXHAUST FLAP

630E-259

ENGINE ECU

DENOX 2.2 control system is incorporated into the engine control unit (ECU).

The DOC/SCR aftertreatment system is electronically managed by the DENOX 2.2 control system. The ECU calculates and adjusts the flow rate of the DEF solution into the system based on current engine speed, torque delivered, exhaust temperature, amount of nitrogen oxides and ammonia present and the humidity levels in incoming air.

250D-053

EXHAUST FLAP

An exhaust flap is located at the exhaust outlet from the engine. The exhaust flap is used to regulate temperature of the exhaust entering the diesel oxidation catalyst (DOC) to optimum levels for proper operation of the aftertreatment system.

3.42

Tigercat T234B Track Loader

Lubrication and Maintenance

DOSING MODULE (DEF INJECTOR)

CATALYTIC CONVERTER

DOSING MODULE

CATALYTIC CONVERTER

250D-056

DOSING MODULE

The dosing module is mounted on the DOC outlet upstream of the catalytic converter. The dosing module injects DEF into the exhaust pipe. Note that this module must be mounted at the correct specified angle to function properly.

The dosing module is cooled by a constant flow of engine coolant supplied by the heater valve to maintain optimum temperature for the aftertreatment process.

MIXER TUBE DOC

MIXER TUBE

234B-084

CATALYTIC CONVERTER

The catalytic converter is located on the left side of the engine compartment. Chemical reactions inside the catalytic converter reduce nitrogen oxides (NOx) in the exhaust gas.

The catalytic converter is equipped with soundproofing material and replaces the exhaust silencer. It incorporates both the selective catalytic reduction (SCR) and the cleanup catalyst (CUC) components of the aftertreatment system.

The first phase of the SCR process takes part in the first part of the catalytic converter: high temperature exhaust gas evaporates the DEF solution instantly and, by hydrolysis, converts it into ammonia (2NH3) and carbon dioxide (CO2).

Evaporation of the solution lowers exhaust gas temperature, bringing it closer to the optimum temperature required by the process.

T250D-119

MIXER TUBE

The mixer tube is incorporated into the outlet of the DOC upstream from the catalytic converter.

The insulated high-turbulence mixer tube is used to mix the DEF solution and exhaust gases together before they enter the catalytic converter.

The exhaust fumes and ammonia at the proper reaction temperature, are introduced into the catalytic converter, where the second phase of the process takes place: by reacting with the oxygen in the exhaust gasses the ammonia is converted into free nitrogen (N2) and water vapour (H2O).

Finally the high efficiency catalytic converter incorporates a clean up catalyst (CUC) which reduces any excess ammonia (NH3) which may result from the SCR process.

3.43

Lubrication and Maintenance

Tigercat T234B Track Loader

HUMIDITY SENSOR

TEMPERATURE SENSORS Three temperature sensors are mounted at the inlet of the diesel oxidation catalyst and the inlet and outlet of the catalytic converter.

DOC INLET TEMP SENSOR

620E-089

HUMIDITY SENSOR

The humidity sensor is located on the air intake just past the air cleaner.

250D-060

HUMIDITY SENSOR

CATALYTIC CONVERTER INLET TEMP SENSOR

250D-061 250D-059

This sensor monitors the temperature and humidity of intake air sending signals to the Denox 2.2 control sytem. This information is used to calculate the amount of DEF to be injected into the system.

CATALYTIC CONVERTER OUTLET TEMP SENSOR

TAG

250D-062

These three sensors send exhaust temperature signals to the DENOX 2.2 control system. The control system uses this information to calculate the amount of DEF to be injected into the system.

NOTE: All three temperature sensors are identical, however location should be noted for analysis purposes when replacing a temperature sensor.

620E-087

TEMPERATURE SENSOR 3.44

Tigercat T234B Track Loader NH3 SENSOR

Lubrication and Maintenance NOx SENSOR ELECTRONIC CONTROL UNIT

ELECTRONIC CONTROL UNIT

SENSOR NOx SENSOR

NH3 SENSOR

630E-264

NOx SENSOR

620E-088

The NH3 sensor is mounted at the outlet of the catalytic converter and the NH3 sensor ECU is mounted on a bracket next to the radiator on the left side of the engine compartment .

There are 2 x NOx sensors and 2 x NOx sensor ECU's in the aftertreatment system.

CATALYTIC CONVERTER OUTLET TUBE

NH3 SENSOR

INLET NOx SENSOR 250D-063 250D-065

INLET NOx SENSOR INLET NOx SENSOR ECU

NH3 SENSOR ECU

250D-064

The NH3 sensor detects and sends information about the NH3 levels in the exhaust. This information is used to calculate the amount of DEF to be injected into the system and to monitor DOC/ SCR aftertreatment system operation.

Refer to APPROVED ANTI-SEIZE PASTES FOR EXHAUST / AFTERTREATMENT LINE (TIGERCAT BY FPT TIER 4F ENGINES) in SECTION 3.

250D-066

INLET NOx SENSOR ECU

The inlet NOx sensor is mounted upstream of the diesel oxidation catalyst and the inlet NOx sensor ECU is mounted above the vacuum pump at the back of the hydraulic oil tank.

3.45

Lubrication and Maintenance

Tigercat T234B Track Loader IMPORTANT! When checking or replacing any sensor or plugs in the exhaust or the aftertreatment system it is important to use only approved anti-seize as specified by Tigercat.

OUTLET NOx SENSOR

Use of non-approved compounds can affect the operation of the NOx sensor and cause a malfunction of the DOC/SCR aftertreatment system. This may result in poisoning of the catalytic converter and require replacement of expensive aftertreatment system parts.

250D-063

OUTLET NOx SENSOR

APPROVED ANTI-SEIZE PASTES FOR EXHAUST / AFTERTREATMENT LINE (TIGERCAT BY FPT Tier 4F ENGINES) NOx sensors-Weicon High Tech Anti-seize only NH3 sensor-Loctite X203 Dry Film Moly Anti-Seize

OUTLET NOx SENSOR ECU

250D-064

OUTLET NOx SENSOR ECU

The outlet NOx sensor is mounted at the outlet of the catalytic converter and the outlet NOx sensor ECU is mounted on the same bracket as the NH3 sensor ECU next to the radiator of the left side of the engine compartment.

The NOx sensors detect and send information about the dosing of DEF solution and the efficiency of the catalytic converter to the Denox 2.2 control system. This information is used to calculate the amount of DEF to be injected into the system and to monitor DOC/SCR aftertreatment system operation.

Each NOx sensor consists of ceramic sensor and an electronic control unit linked by a cable. The sensor detects the concentration of nitrogen oxides in the exhaust.

The sensor, cable and control unit are considered to be one part for service/replacement purposes.

Note that cable length cannot be changed as this will affect the proper operation of the sensor.

3.46

Tigercat T234B Track Loader

Lubrication and Maintenance

DIESEL EXHAUST FLUID (DEF) HANDLING

AVOID DEF QUALITY PROBLEMS WITH PROPER HANDLING PRACTICES

Diesel exhaust fluid (DEF) is an aqueous urea solution with 32.5% high purity urea and 67.5% deionized water. Note that DEF may also be referred to as AUS32 or AdBlue and should meet ISO 22241 specifications. Use only DEF meeting this standard.

Most DEF quality problems can be avoided entirely with a little care and proper handling of DEF.

It is important to avoid contamination of DEF as this may cause costly damage to SCR system components and affect the proper operation of the SCR system and the engine.

When a problem with DEF quality is detected information messages and warnings will be shown on the computer display. Note that DEF quality problems may result in derating of engine performance to meet emission standard requirements. Action to correct DEF quality problems should be taken immediately to avoid affecting engine performance and damage to SCR aftertreatment system components. Refer also to COMPUTER – MESSAGES AND WARNINGS in SECTION 2 or SECTION 6 of the SERVICE MANUAL.

FILLING THE DEF TANK •

Always clean the area around the fill cap and avoid introducing contaminants into the DEF tank when filling.

•

Always use only diesel exhaust fluid (DEF) which meets ISO 22241 specifications.

Use of any other fluid will contaminate the aftertreatment system and may pose a safety hazard.

USE OF PROPER STORAGE CONTAINERS •

To prevent contaminants from affecting DEF quality it should be handled only in storage, transport and filling containers intended exclusively for that purpose.

•

Polyethylene or stainless steel containers are recommended. Refer also to DEF manufacturer's recommendations.

•

DEF is corrosive to metals other than stainless steel. Transport in metal containers other than stainless steel will result in contamination.

For safety information refer to DIESEL EXHAUST FLUID (DEF) in SECTION 1.

WARNING Use only diesel exhaust fluid (DEF) which meets ISO 22241 specifications. NEVER fill the DEF tank with any other fluid.

DEF is injected into the exhaust gas stream during normal operation of the Selective Catalytic Reduction (SCR) aftertreatment system.

Use of other fluids may cause component damage, or a fire risk which could result in death or serious injury.

PROPER STORAGE CONDITIONS TO MAXIMIZE SHELF LIFE •

DEF should be stored between -11°C (12°F) and 30°C (86°F) and out of direct sunlight to maximize shelf life and to avoid DEF quality problems caused by improper storage.

•

DEF quality problems can often be avoided with proper storage and handling practices to maximize shelf life.

•

DEF storage areas should always be out of direct sunlight and away from heat sources to avoid reducing shelf life.

•

DEF shelf life is limited. It should be consumed on a first in first out basis, within manufacturer's recommended shelf life limits.

DEF beyond manufacturer's recommended shelf life limits may not meet ISO 22241 specifications.

3.47

Lubrication and Maintenance

Tigercat T234B Track Loader

CHECKING AIR CONDITIONING SYSTEM

CAUTION

IMPORTANT! It is recommended that during cold weather when the A/C system is not in use, that it be run for a period of 5 minutes every two weeks to circulate oil to all components of the system.

R134a REFRIGERANT Without cab riser: 2.7 kg (94 oz) With cab riser: 2.9 kg (104 oz)

PAG OIL 89 mL (3.0 oz) 104 mL (3.5 oz)

Any service work must be performed by authorized A/C technicians. The system should be charged with R134a refrigerant. At least the minimum amount of PAG (polyalkylene glycol) oil, shown above, should be present in the system and must be used on O-rings and fittings during assembly.

• If using compressed air for cleaning, use 2 bar (30 psi) or less.

• Always use personal protective equipment to guard against flying debris.

Use the following checklist to maintain system between service intervals. The compressor and charge valves are located on the left side of the engine and accessible through the engine compartment door. The receiver dryer is located in the lower engine compartment beside the front left engine mount and accessible from either underneath the engine compartment or through the engine compartment door.

Perform the following checks on system:

A/C COMPRESSOR

234E-293

A/C COMPRESSOR BELT

SERPENTINE FAN BELT

A/C COMPRESSOR

234E-285

ENGINE BELTS

a. Check and adjust compressor drive belt tension. Do not over tighten. b. Check fresh air filter and re-circulating air filter.

Clean or replace as required. c. Check to see that compressor clutch will engage. d. Check blower operation and air vents. e. Check the condenser core for dirt and debris.

3.48

Tigercat T234B Track Loader CLEANING COOLER PACKAGE

The A/C condenser core is located on the right side of the machine and is one of the cores in a stack of four that make up the cooler package.

The cooling fan is mounted on the front of the engine. The fan draws air from the right side of the machine through the door screen and the cooler package blowing it out of the opposite side of the machine.

Lubrication and Maintenance PROCEDURE:

CHARGE AIR COOLER T250D-029

OPEN THE SCREEN DOOR ON R.H. SIDE OF ENGINE COMPARTMENT

RADIATOR

A/C CONDENSER

Remove the 3 capscrews and washers and swing open the screen door on the right side of the engine compartment.

CAUTION

OIL COOLER

234E-288

CHECK CHARGE AIR COOLER, RADIATOR, A/C CONDENSER AND OIL COOLER The cooler package should be manually checked every 8 hours (every shift) or more often where conditions cause accumulation of twigs, leaves, pine needles and dust. All of the engine enclosure doors should also be checked.

• If using compressed air for cleaning, use 2 bar (30 psi) or less.

• Always use personal protective equipment to guard against flying debris.

This cooler package must be checked daily and may require thorough cleaning on a regular basis depending on operating conditions. Compressed air or water may be used for cleaning. Use personal protective equipment to guard against flying debris.

If an oil leak occurs in this area it should be thoroughly power-washed with a mild soap to ensure that all of the oil is removed. The presence of oil causes dust and dirt to cling to surfaces which will impair the reversible fan's ability to remove dust and dirt particles.

Care must be taken when cleaning this unit, as the components can be damaged by careless handling and cleaning.

3.49

Lubrication and Maintenance

Tigercat T234B Track Loader

PRESSURE SETTINGS Engine rpm...........................................................................2000 rpm Engine rpm...........................................................................1200 rpm

@ Full throttle (no load) @ Idle (no load)

Pilot System Main Relief ........................................ 34.5 Bar (500 psi) + 1/2 turn in

@ Idle

Main Valve High Pressure Limiting Control MAIN PUMP P.O.R. (‘PX’ port)............................ 288 Bar (4175 psi) Margin Pressure (‘PX’ - ‘LS’).................................... 26 Bar (375 psi)

@ Full throttle @ Idle (See Note 6)

Main Valve Port reliefs Hoist DOWN........................................................................ **Mode 3 Hoist UP.............................................................................. **Mode 3 Stick IN................................................................................ **Mode 3 Stick OUT............................................................................ **Mode 3 Feed Reducer Live Heel Retract......................... 221 Bar (*3200 psi) Feed Reducer Live Heel Extend......................... 221 Bar (*3200 psi) Feed Reducer Grapple OPEN............................ 172 Bar (*2500 psi) Feed Reducer Grapple CLOSE.......................... 172 Bar (*2500 psi) Feed Reducer Saws RETRACT......................... 172 Bar (*2500 psi) Feed Reducer Saws CUT.................................... 172 Bar (*2500 psi) Feed Reducer Grapple Rotate CCW................... 121 Bar (*1750 psi) Feed Reducer Grapple Rotate CW..................... 121 Bar (*1750 psi) Feed Reducer Delimber OPEN........................... 172 Bar (*2500 psi) Feed Reducer Grapple Saw (Option).................. 207 Bar (*3000 psi) R.H. Track Forward/Reverse............................................ See Note 7 L.H. Track Forward/Reverse............................................ See Note 7 Drive Brake Release Pressure (See Note 10).......... 45 Bar (650 psi) Drive Begin Of Regulation (See Note 8).............. 214 Bar (3100 psi) Note: Pressures set at Idle unless otherwise specified. * Set pressure with gauge on 'LS' port Cab Tilt Cab Tilt Main Relief............................................... 207 Bar (3000 psi) Cab Tilt Counterbalance Valves............................ 241 Bar (3500 psi)

7.0 Seconds @ Full throttle 8.0 Seconds @ Full throttle 6.0 Seconds @ Full throttle 6.0 Seconds @ Full throttle 4.0 Seconds @ Full throttle 4.0 Seconds @ Full throttle @ Idle @ Idle @ Idle @ Idle @ Idle (See Note 5) @ Idle (See Note 5) @ Idle @ Idle @ Idle @ Idle @ Full throttle, Not Adjustable @ Idle

Engine Off Engine Off

Swing Pump Charge Pressure ...................................................... 28 Bar (400 psi) @ Idle Pump POR ........................................................... 290 Bar (4200 psi) @ Full throttle HIGH PRESSURE RELIEF Swing CCW................310 Bar (4500 psi) @ Idle HIGH PRESSURE RELIEF Swing CW..................310 Bar (4500 psi) @ Idle Swing machine slowly 5 times in each direction before setting pressures. Do not hold pressure over relief more than 8 seconds at a time. Wait 5 seconds to avoid overheating.

Note: Pressures set at Idle unless otherwise specified.

ALL PRESSURES MUST BE SET WITH HYDRAULIC OIL AT OPERATING TEMPERATURE. NOTE: The above values are for reference purposes only, SEE SERVICE MANUAL FOR SETTING PROCEDURE.

3.50

Tigercat T234B Track Loader

Lubrication and Maintenance

PRESSURE SETTINGS NOTES: 1. SYSTEM TO BE AT OPERATING TEMPERATURE WHEN SETTING PRESSURES. 2. ALL PRESSURES MEASURED IN PSI. ALL SPEEDS MEASURED IN SECONDS. BOOM SPEED SHOULD BE MEASURED WITH THE GRAPPLE INSTALLED. IF GRAPPLE IS NOT INSTALLED, THEN ONLY MEASURE HOIST UP AND STICK OUT TIMES. 3. F - DENOTES PRESSURES SET AT FULL ENGINE RPM. I - DENOTES PRESSURES SET AT ENGINE IDLE. 4. PORT RELIEFS CANNOT BE ADJUSTED. EACH PORT RELIEF HAS A SPECIFIC SETTING AND SHOULD NOT BE INTERCHANGED WITH OTHER PORT RELIEFS. 5. FOR ROTOBEC HD(HEAVY DUTY) AND HULTDINS GRAPPLES SET ROTATE TO 3000 PSI. 6. SET MARGIN PRESSURE WITH PILOT SYSTEM ACTIVATED (DO NOT USE ANY FUNCTIONS). THIS IS THE TOP ADJUSTMENT ON THE MAIN PUMP. 7. TRACK SPEEDS SET TO 12 RPM LOW AND 28 RPM HIGH BY MAKING ADJUSTMENTS IN THE FOLLOWING ORDER: A) SET MOTOR MAXIMUM DISPLACEMENT TO 105cc.

B) SET LOW FORWARD (VALVE FLOW SETTING).

C) SET HIGH FORWARD (MOTOR MINIMUM DISPLACEMENT).

D) SET HIGH REVERSE (VALVE FLOW SETTING).

8. TRACK DRIVE BEGIN OF REGULATION VALVES TO BE SET AT ENGINE IDLE USING THE FOLLOWING PROCEDURE: A) DISCONNECT AND PLUG BOTH MOTOR BRAKE RELEASE LINES. B) LOWER MAIN PUMP P.O.R. TO 3100 PSI. AT IDLE C) OPERATE TRACK IN HIGH SPEED (TRACK SHOULD NOT MOVE).

D) ADJUST BEGIN OF REGULATION VALVE ON EACH MOTOR TO GIVE PRESSURE BEWTEEN 800 AND 1000 PSI AT MOTOR TEST PORT. E) RESET MAIN PUMP P.O.R. AT FULL ENGINE RPM AND RECONNECT BRAKE LINES. 9. TILT CAB NOTES: A) TURN COUNTERBALANCE VALVES OUT FULLY, THEN IN 1 TURN. B) TILT VALVE IS FACTORY PRESET. 10. DRIVE BRAKE RELEASE PRESSURE IS NOT ADJUSTABLE. TURN SCREW OUT TO ALLOW VALVE TO WORK PROPERLY.

3.51

Lubrication and Maintenance

Tigercat T234B Track Loader

TORQUE CHART TORQUE (LUBRICATED)

LOCATION

THREAD DIAMETER

Cylinders Piston nut, hoist boom cylinder Piston nut, stick cylinder Piston nut, heel cylinder Gland bolts, heel cylinder Gland bolts, hoist boom cylinder Gland bolts, stick boom cylinder

M60-2 6H M60-2 6H M60-2 6H M14-2 (10.9) M14-2 (10.9) M14-2 (10.9)

3230 3230 3230 111 111 111

4380 4380 4380 150 150 150

Boom joint and cylinder pin retaining bolts

M20-2.5 (10.9)

290

393

Hoist and Stick boom pin retaining nut

2"-12 UNF (G8)

Until snug

Until snug

1 3/4"-12 UNF (G8)

400

540

Cab securing bolts

7/8"-9 UNC (G8)

400-450

540-610

Swing bearing bolts Swing gearbox mounting bolts Swing motor mounting bolts

Engine mounting Bolts, bracket/mount to chassis Bolts, bracket to engine Flex drive coupling hub setscrew Engine cooling fan mounting bolts

7/8"-9 UNC (G8) M20-2.5 (10.9) M14-2 (10.9)

450 400 130

610 540 176

7/8"-9 UNC (G8) M12-1.75 (10.9) M10-1.5 (12.9)

400-450 80 89 40

540-610 108 120 54

M10-1.5 (10.9) M10-1.5 (10.9)

34 45

46 61

Pump mounting Main Pump to Engine Swing Pump to Main Pump

3/4"-10 UNC (G8) M16-2 (10.9)

280 165

380 224

Undercarriage Track shoe bolts Idler bolts Roller mounting bolts Sprocket bolts Gearbox mounting bolts Drive motor mounting bolts

3/4 UNF M16-2 (10.9) 7/8"-9 UNC (G8) M20-2.5 (10.9) M20-2.5 (10.9) M20-2.5 (8.8)

T/T* 175 450 380 380 275

T/T* 237 610 515 515 373

Heel to Stick boom pin retaining nut

Pump drive Flex drive coupling to flywheel Plate to bell housing

lbf-ft

Nm

*T/T represents Torque-Turn, this is a method of torquing the track shoe bolts. Refer to SECTION 11 in the Tigercat SERVICE MANUAL for a complete description on this method of applying torque.

Torque values pertaining to the engine and attachment are provided in the appropriate manuals.

3.52

Tigercat T234B Track Loader

Lubrication and Maintenance

GENERAL TORQUE SPECIFICATIONS

IMPERIAL

The torque values listed below are for general use only.

DO NOT use these values if a different torque value or tightening procedure is shown for a specific application.

GRADE 5 BOLTS

GRADE 8 BOLTS

IMPERIAL BOLT TORQUE SPECIFICATIONS GRADE 8 BOLTS GRADE 5 BOLTS LUBRICATED lbf-ft Nm 8 - 10 11 - 13 20 - 28 27 - 38 33 - 36 45 - 49 52 - 57 71 - 77 80 - 88 109 - 119 115 - 127 156 - 172 159 - 175 216 - 237 282 - 310 393 - 420 455 - 501 617 - 679 682 - 750 925 - 1016 966 - 1062 1310 - 1441 1360 - 1496 1844 - 2027 LUBRICATED lbf-ft Nm 10 - 13 14 - 17 18 - 25 25 - 33 37 - 41 50 - 55 58 - 64 79 - 86 90 - 99 122 - 134 128 - 141 174 - 191 180 - 198 244 - 268 315 - 347 427 - 470 501 - 550 679 - 745 746 - 821 1012 - 1113 1083 - 1191 1469 - 1613 1509 - 1660 2046 - 2250 8.8

10.9

8.8

10.9

8.8

10.9

10

10

10

METRIC

DRY LUBRICATED COARSE THREAD lbf-ft Nm lbf-ft Nm 1/4" - 20 7- 8 10 - 11 8 - 10 11 - 13 5/16" - 18 14 - 18 19 - 24 10 - 15 13 - 20 3/8" - 16 31 - 34 42 - 46 23 - 25 31 - 34 7/16" - 14 49 - 54 66 - 73 37 - 41 50 - 55 1/2" - 13 75 - 83 102 - 112 57 - 63 77 - 85 9/16" - 12 109 - 120 148 - 162 82 - 90 111 - 122 5/8" - 11 150 - 165 204 - 223 113 - 124 152 - 168 3/4" - 10 266 - 293 360 - 397 200 - 220 271 - 298 7/8" - 9 394 - 433 535 - 586 296 - 326 402 - 441 1" - 8 591 - 649 802 - 879 443 - 489 601 - 663 1 1/8" - 7 794 - 873 1077 - 1183 596 - 656 808 - 889 1 1/4" - 7 1120 - 1232 1519 - 1670 840 - 924 1139 - 1252 FINE DRY LUBRICATED lbf-ft Nm lbf-ft Nm THREAD 1/4" - 28 9 - 10 12 - 13 9 - 10 12 - 13 5/16" - 24 17 - 22 23 - 29 16 - 20 21 - 27 3/8" - 24 35 - 39 48 - 53 26 - 29 35 - 39 7/16" - 20 55 - 61 75 - 83 41 - 45 56 - 61 1/2" - 20 85 - 94 116 - 127 64 - 70 87 - 95 9/16" - 18 121 - 133 164 - 180 91 - 100 124 - 135 5/8" - 18 170 - 187 231 - 253 128 - 141 174 - 191 3/4" - 16 297 - 327 403 - 443 223 - 245 303 - 332 7/8" - 14 434 - 477 589 - 646 326 - 359 442 - 486 1" - 12 646 - 711 876 - 965 484 - 534 657 - 724 1 1/8" - 12 891 - 980 1208 - 1328 668 - 735 906 - 996 1 1/4" - 12 1240 - 1364 1682 - 1849 931 - 1024 1262 - 1387

10

12.9

12.9

10

12.9

12.9

12.9

12

12

DRY lbf-ft Nm 11 - 12 15 - 16 26 - 30 35 - 40 44 -48 60 - 65 70 - 77 95 - 104 106 - 117 144 - 158 153 - 168 208 - 228 212 - 233 288 - 316 376 - 414 510 - 561 606 - 667 822 - 904 909 - 1000 1233 - 1355 1288 - 1417 1746 - 1921 1817 - 1999 2464 - 2710 DRY lbf-ft Nm 13 - 14 18 - 19 23 - 28 31 - 38 49 - 54 67 - 73 78 - 86 106 - 116 120 - 132 163 - 179 171 - 188 232 - 255 240 - 264 326 - 358 420 - 462 570 - 626 668 - 735 906 - 996 995 - 1096 1359 - 1486 1445 - 1590 1960 - 2155 2012 - 2213 2728 - 2997

10

COARSE THREAD 1/4" - 20 5/16" - 18 3/8" - 16 7/16" - 14 1/2" - 13 9/16" - 12 5/8" - 11 3/4" - 10 7/8" - 9 1" - 8 1 1/8" - 7 1 1/4" - 7 FINE THREAD 1/4" - 28 5/16" - 24 3/8" - 24 7/16" - 20 1/2" - 20 9/16" - 18 5/8" - 18 3/4" - 16 7/8" - 14 1" - 14 1 1/8" - 12 1 1/4" - 12

12

METRIC BOLT TORQUE SPECIFICATIONS CLASS 8.8

SIZE PITCH LUBRICATED mm Nm lbf-ft M6 1 8-9 6-7 M8 1.25 20 - 22 15 - 16 M10 1.5 39 - 43 29 - 32 M12 1.75 68 - 75 50 - 55 M14 2 109 - 120 80 - 89 M16 2 169 - 186 125 - 137 M18 2.5 234 - 257 172 - 190 M20 2.5 330 - 364 244 - 268 M22 2.5 451 - 496 332 - 366 M24 3 571 - 628 421 - 463 M27 3 837 - 921 618 - 679 M30 3.5 1135 - 1249 837 - 921 M33 3.5 1545 - 1699 1139 - 1253 M36 4 1985 - 2183 1464 - 1610

CLASS 10.9 LUBRICATED DRY Nm lbf-ft Nm lbf-ft Nm lbf-ft 11 - 12 8-9 11 - 12 8-9 15 - 17 11 - 12 26 - 29 19 - 21 27 - 30 20 - 22 36 - 40 27 - 30 52 - 57 38 - 42 54 - 60 40 - 44 72 - 79 53 - 59 91 - 100 67 - 74 94 - 104 70 - 77 126 - 138 93 - 102 145 - 160 107 - 118 151 - 166 111 - 122 201 - 221 148 - 163 226 - 248 166 - 183 234 - 257 173 - 190 312 - 343 230 - 253 312 - 343 230 - 253 324 - 356 239 - 262 431 - 474 318 - 350 441 - 485 325 - 357 457 - 503 337 - 371 610 - 670 450 - 495 601 - 661 443 - 487 623 - 686 460 - 506 831 - 914 613 - 674 761 - 838 562 - 618 790 - 869 583 - 641 1053 - 1159 777 - 855 1116 - 1228 823 - 906 1158 - 1274 854 - 940 1544 - 1699 1139 - 1253 1514 - 1665 1116 - 1228 1570 - 1727 1158 - 1274 2094 - 2303 1544 - 1699 2060 - 2266 1519 - 1671 2137 - 2351 1576 - 1734 2849 - 3134 2102 - 2312 2646 - 2911 1952 - 2147 2745 - 3020 2025 - 2227 3661 - 4027 2700 - 2970 DRY

3.53

CLASS 12.9 LUBRICATED DRY Nm lbf-ft Nm lbf-ft 13 - 14 10 - 11 18 - 19 13 - 14 32 - 35 24 - 26 43 - 47 31 - 35 63 - 70 47 - 51 84 - 93 62 - 68 110 - 121 81 - 90 147 - 162 109 - 119 176 - 194 130 - 143 235 - 259 173 - 191 274 - 301 202 - 222 365 - 401 269 - 296 378 - 416 279 - 307 504 - 554 372 - 409 534 - 588 394 - 433 712 - 784 525 - 578 728 - 801 537 - 591 971 - 1068 716 - 788 923 - 1016 681 - 749 1231 - 1354 908 - 999 1354 - 1489 998 - 1098 1805 - 1985 1331 - 1464 1835 - 2019 1354 - 1489 2447 - 2692 1805 - 1985 2498 - 2747 1842 - 2026 3330 - 3663 2456 - 2702 3208 - 3529 2366 - 2603 4278 - 4706 3155 - 3471

Lubrication and Maintenance

Tigercat T234B Track Loader

Parker

Assembly Torque The four-bolt port is simply a circular opening (flow passage) surrounded by four tapped holes in a certain pattern for acceptance of the flange clamping bolts. The flat surface of the port compresses the O-ring contained in the groove in the flange head when the clamp bolts are torqued. In some instances, the groove is in the port and not in the flange head. The bolts, through the clamp halves, clamp down the flange head on to the flat surface of the port compressing and trapping the O-ring in the groove and leaving no gap for it to extrude under pressure. The hydraulic pressure is thus sealed by the compressed O-ring as long as the bolts are tightened enough to maintain solid metal to metal contact between the flange head at the outside diameter of the O-ring and the top of the port.

The 4-Bolt Split Flange consists of four main components: • A body (flange head) • An O-ring • One “captive” or two “split” flange clamps

• Four bolts and washer

WASHERS BOLTS FLANGE CLAMP

Flange Port Assembly

FLANGE HEAD

The steps to properly assemble the flange port clamping bolts are: 1. Make sure sealing surfaces are free of burrs, nicks, scratches or any foreign particles.

2. Lubricate the O-ring.

3. Position flange and clamp halves.

4. Place lock washers on bolts and insert through clamp halves.

5. Hand tighten bolts.

6. Torque bolts in diagonal sequence (see Fig. T9) in small increments to the appropriate torque level listed in Table T6 or Table T7 on this page.

O-RING TAPPED HOLES

FLANGE.JPG

Fig. T8 - 4 Bolt Split Flange Components

FLANGE2.JPG

Fig. T9 - Flange Bolt Tightening Sequence

Dash Size

Flange Size

Inch Bolt (J518)

Torque lbf-ft

Metric Bolt (ISO 6162)

Torque Nm

Dash Size

Flange Size

Inch Bolt (J518)

Torque lbf-ft

Metric Bolt (ISO 6162)

Torque N-m

8 12 16 20 24 32 40 48 56 64 80

1/2 3/4 1 1-1/4 1-1/2 2 2-1/2 3 3-1/2 4 5

5/16-18 3/8-16 3/8-16 7/16-14 1/2-13 1/2-13 1/2-13 5/8-11 5/8-11 5/8-11 5/8-11

17 +/- 2 25 +/- 3.5 31 +/- 4.5 41 +/- 5 52 +/- 6 60 +/- 6 85 +/- 9 144 +/- 15 125 +/- 8 125 +/- 8 125 +/- 8

M8 M10 M10 M12 M12 M12 M12 M16 M16 M16 M16

25 49 49 85 85 135 95 220 220 220 220

8 12 16 20 24 32

1/2 3/4 1 1 1/4 1 1/2 2

5/16-18 3/8-16 7/16-14 1/2-13 5/8-11 3/4-10

17 +/- 2 30 +/- 4.5 46 +/- 4.5 69 +/- 6 125 +/- 8 208 +/- 20

M8 M10 M12 M14 M16 M20

25 49 85 135 210 425

* Does not meet ISO 6162 specification.

Table T7 - Code 62 Flange Recommended Bolt Torque

3.54

Tigercat T234B Track Loader

Lubrication and Maintenance

Parker

Assembly Torque

JIC 37 Degree Flare SAE Dash Size

Thread Size

-2 -3 -4 -5 -6 -8 -10 -12 -14 -16 -20 -24 -32 -40

NPTF

Tube Connection Swivel or Hose Connection FFWR FFWR

5/16-24 3/8-24 7/16-20 1/2-20 9/16-18 3/4-16 7/8-14 1 1/16-12 1 3/16-12 1 5/16-12 1 5/8-12 1 7/8-12 2 1/2-12 3-12

NA NA 2 2 1 1/2 1 1/2 1 1/2 1 1/4 1 1 1 1 1 1

SAE Dash Size

NA NA 2 2 1 1/4 1 1 1 1 1 1 1 1 1

-2 -3 -4 -5 -6 -8 -10 -12 -14 -16 -20 -24 -32 -40

F.F.W.R : Flats From Wrench Resistance All values are for Steel, Stainless Steel and Brass

1/8-27 NA 1/4-18 NA 3/8-18 1/2-14 7/8-14 3/4-14 NA 1-11 1/2 1 1/4-11 1/2 1 1/2-11 1/2 2-11 1/2 NA

Thread Size

-2 -3 -4 -5 -6 -8 -10 -12 -14 -16 -20 -24 -32 -40

NA NA 1/4 TO 1/2 NA 1/4 TO 1/2 1/4 TO 1/2 1/4 TO 1/2 1/4 TO 1/2 NA 1/4 TO 1/2 1/4 TO 1/2 1/4 TO 1/2 NA NA

2-3 NA 2-3 NA 2-3 2-3 NA 2-3 NA 1.5-2.5 1.5-2.5 1.5-2.5 1.5-2.5 NA

BSPT

Tube Connection Swivel or Hose Connection FFWR FFWR

NA NA 9/16-18 NA 11/16-16 13/16-16 1-14 1 3/16-12 NA 1 7/16-12 1 11/16-12 2-12 NA NA

2-3 NA 2-3 NA 2-3 2-3 NA 2-3 NA 1.5-2.5 1.5-2.5 1.5-2.5 1.5-2.5 NA

T.F.F.T. : Turns from finger tight All pipe values are for Steel, Stainless Steel and Brass

O'ring Face Seal / Seal-Lok SAE Dash Size

Tube Connection Swivel or Hose Connection TFFT TFFT

Thread Size

SAE Dash Size

NA NA 1/2 TO 3/4 NA 1/2 TO 3/4 1/2 TO 3/4 1/2 TO 3/4 1/3 TO 1/2 NA 1/3 TO 1/2 1/3 TO 1/2 1/3 TO 1/2 NA NA

-2 -3 -4 -5 -6 -8 -10 -12 -14 -16 -20 -24 -32 -40

F.F.W.R : Flats From Wrench Resistance All values are for Steel, Stainless Steel and Brass

Thread Size

Tube Connection Swivel or Hose Connection TFFT TFFT

1/8-28 NA 1/4-19 NA 3/8-19 1/2-14 NA 3/4-14 NA 1-11 1 1/4-11 1 1/2-11 2-11 NA

2-3 NA 2-3 NA 2-3 2-3 NA 2-3 NA 1.5-2.5 1.5-2.5 1.5-2.5 1.5-2.5 NA

2-3 NA 2-3 NA 2-3 2-3 NA 2-3 NA 1.5-2.5 1.5-2.5 1.5-2.5 1.5-2.5 NA

T.F.F.T. : Turns from finger tight All pipe values are for Steel, Stainless Steel and Brass

SAE J1926 Straight Thread Port Assembly Torques ASSEMBLY TORQUE = 10 % -0 SAE DASH SIZE

2 3 4 5 6 8 10 12 14 16 20 24 32

THREAD SIZE

5/16-24 3/8-24 7/16-20 1/2-20 9/16-18 3/4-16 7/8-14 1 1/16-12 1 3/16-12 1 5/16-12 1 5/8-12 1 7/8-12 2 1/2-12

SEAL-LOK lbf-ft (lbf-in) (310) (310) (310) (360) (420) 60 100 135 175 200 250 305 375

Nm 20 20 20 40 46 80 135 185 235 270 340 415 510

TRIPLE-LOK FERULOK PIPE FITTINGS lbf-ft Nm (lbf-in) (85) 10 (155) 18 (260) 29 (280) 32 (350) 40 (620) 70 85 115 135 183 175 237 200 271 250 339 305 414 375 509

PLUGS

ADJUSTABLE

NON-ADJUSTABLE

SEAL-LOK lbf-ft (lbf-in) (310) (310) (310) (360) (420) 60 100 135 175 200 250 305 375

3.55

Nm 20 20 20 40 46 80 135 185 235 270 340 415 510

TRIPLE-LOK FERULOK PIPE FITTINGS lbf-ft Nm (lbf-in) (60) 7 (100) 11 (180) 20 (250) 28 (350) 40 (620) 70 85 115 135 183 175 237 200 271 250 339 305 414 375 509

HOLLOW HEX HP5ON-S lbf-ft (lbf-in) (30) (55) (120) (170) (410) 60 100 135 175 200 250 305 375

Nm 3.5 6 13.5 19 46 80 135 185 235 270 340 415 510

HEX HEAD P5ON-S lbf-ft (lbf-in) (85) (155) (260) (280) (350) (620) 85 135 175 200 250 305 375

Nm 10 18 29 32 40 70 115 183 237 271 339 414 509

Lubrication and Maintenance

Tigercat T234B Track Loader

EATON Aeroquip

Assembly Torque

Recommended Parallel Connection Assembly torque

Eaton recommends that a Torque wrench be used to assure proper fitting assembly of these connections.

Straight Thread O-Ring Boss Low Pressure with 37º (SAEJ514)

Straight Thread O-Ring Boss High Pressure with ORS (J1453)

Thread Size (inches) 3/8-24 7/16-20 1/2-20 9/16-18 3/4-16 7/8-14 1 1/16-12 1 3/16-12 1 5/16-12 1 5/8-12 1 7/8-12 2 1/2-12

Dash Size -03 -04 -05 -06 -08 -10 -12 -14 -16 -20 -24 -32

The values listed are for steel connections. Contact Teaton for torque values for other materials.

Jam Nut or Jam Nut or Straight Straight Fitting Torque Fitting Torque lb.-ft.

Newton Meters 8-9 12-13 13-15 18-20 14-15 19-21 23-24 32-33 40-43 55-57 43-48 59-64 68-75 93-101 83-90 113-122 112-123 152-166 146-161 198-218 154-170 209-230 218-240 296-325

Dash Size -03 -04 -05 -06 -08 -10 -12 -14 -16 -20 -24

ORS

Dash Size -04 -06 -08 -10 -12 -16 -20 -24

Thread Size (inches) 3/8-24 7/16-20 1/2-20 9/16-18 3/4-16 7/8-14 1 1/16-12 1 3/16-12 1 5/16-12 1 5/8-12 1 7/8-12

Jam Nut or Jam Nut or Straight Straight Fitting Torque Fitting Torque lb.-ft.

Newton Meters 8-10 11-16 14-16 20-22 18-20 24-27 24-26 33-35 50-60 68-78 72-80 98-110 125-135 170-183 160-180 215-245 200-220 270-300 210-280 285-380 270-360 370-490

SAE 37º (JIC) Thread Size (inches) 9/16-18 11/16-20 13/16-16 1-14 1 3/16-12 1 7/16-12 1 11/16-12 2-12

Swivel Nut Torque lb.-ft.

10-12 18-20 32-35 46-50 65-70 92-100 125-140 150-165

Swivel Nut Torque Newton Meters 14-16 24-27 43-47 62-68 88-95 125-136 170-190 204-224

Dash Size -04 -05 -06 -08 -10 -12 -16 -20 -24 -32

Metric Thread Size mm M10x1 M12x1.5 M14x1.5 M16x1.5 M18x1.5 M20x1.5 M22x1.5 M26x1.5 M27x2 M33x2 M42x2 M48x2

Thread Size (inches) 7/16-20 1/2-20 9/16-18 3/4-16 7/8-14 1 1/16-12 1 5/16-12 1 5/8-12 1 7/8-12 2 1/2-12

Swivel Nut Torque lb.-ft.

11-12 15-16 18-20 38-42 57-62 79-87 108-113 127-133 158-167 245-258

Swivel Nut Torque Newton Meters 15-16 20-22 24-28 52-58 77-85 108-119 148-154 173-182 216-227 334-352

BSPP Straight Adapter or Locknut Torque lb.-ft.

Newton Meters 13-15 18-20 15-19 20-25 19-23 25-30 33-40 45-55 37-44 50-60 52-66 70-90 55-70 75-95 81-96 110-130 96-111 130-150 162-184 220-250 170-192 230-260 258-347 350-470

Nominal Thread Size Straight Adapter or Locknut Torque inches** lb.-ft.

Newton Meters G1/8-28 13-15 18-20 G1/4-19 19-23 25-30 G3/8-19 33-40 45-55 G1/2-14 55-70 75-95 G3/4-14 103-118 140-160 G1-11 162-184 220-250 G1 1/4-11 170-192 230-260 G1 1/2-11 258-347 350-470 ** "G" denotes parallel threads, other than ISO 6149 (Port connection only)

Eaton Aeroquip Fluid Conveyance Products A-HOOV-MC001-E January 2005

3.56

Tigercat T234B Track Loader

Lubrication and Maintenance

Weights of Commercial Wood

Species

kg/m3

lb/ft3

Species

kg/m3

lb/ft3

Alder, Red Ash, White Aspen, Quaking Bald Cypress Basswood, American Beech, American Birch, Paper Birch, Yellow Cedar, Alaska Cedar, Incense Cedar, Northern White Cedar, Port-Orford Cedar, Western Red Cherry, Black Cottonwood, Eastern Douglas Fir, Coast Douglas Fir, Inland North Elm, American Fir, Alpine Fir, Balsam Fir, Nobel Fir, Red Fir, Silver Fir, White Gum, Black Gum, Blue Gum, Red Gum, Tupelo Hemlock, Eastern Hemlock, Western Hickory, Pecan Hickory, True Larch, Western Locust, Black Magnolia, Cucumber

737 769 689 817 673 865 801 929 577 721 449 897 433 721 785 881 577 865 449 721 481 769 577 753 721 1121 801 897 801 657 993 1009 769 929 785

46 48 43 51 42 54 50 58 36 45 28 36 57 45 49 55 36 54 28 45 30 48 36 47 45 70 50 56 50 41 62 63 48 58 49

Maple, Big Leaf Maple, Black Maple, Red Maple, Silver Maple, Sugar Oak, Black Oak, Chestnut Oak, Red Oak, Red, Swamp Oak, Swamp Chestnut Oak, White Oak, White, Swamp Pine, Jack Pine, Loblolly Pine, Lodgepole Pine, Long Leaf Pine, Norway, Red Pine, Short Leaf Pine, Slash Pine, Sugar Pine, Western Yellow Pine, White-Western Pine, White-Eastern Poplar, Yellow Redwood Spruce, Black Spruce, Engleman Spruce, Red Spruce, Sitka Spruce, White Sweetgum Sycamore, American Tamarack Walnut, Black Willow, Black

753 865 801 721 897 1009 977 1009 1073 1041 993 1105 801 993 625 993 673 993 993 817 721 561 577 609 801 513 625 545 529 545 801 833 753 929 801

47 54 50 45 56 63 61 63 67 65 62 69 50 62 39 62 42 62 62 51 45 35 36 38 50 32 39 34 33 34 50 52 47 58 50

Note: The values shown here are green weights.

3.57

Lubrication and Maintenance

Tigercat T234B Track Loader

3.58