Tigercat 726E FELLER BUNCHER OPERATOR'S MANUAL - PDF DOWNLOAD

726E FELLER BUNCHER

OPERATOR’S MANUAL SERIAL NUMBER 7264001 TO 7265000

ISSUE 1.1 JANUARY 2014 Tigercat Industries Inc. P.O. Box 637 Brantford, Ontario Canada N3T 5P9 Tel: (519) 753-2000 Fax: (519) 753-8272

Tigercat 726E Feller Buncher

Introduction

ii

Tigercat 726E FELLER BUNCHER TABLE OF CONTENTS

SECTION INTRODUCTION...............................................................................................................................v STANDARDS, ROPS, FOPS, OPS.................................................................................................. vi NON-APPROVED FIELD PRODUCT CHANGES........................................................................... vii SAFETY.............................................................................................................................................1 USING HIGH SPEED DISC SAWS SAFELY..........................................APPENDIX TO SECTION 1 CONTROLS AND OPERATION........................................................................................................2 LUBRICATION AND MAINTENANCE...............................................................................................3

CALIFORNIA Proposition 65 Warning Diesel engine exhaust and some of its constituents are known to the State of California to cause cancer, birth defects and other reproductive harm.

726E Available Literature Operator's Manual (This Manual)..........................................................Part No. 42525AENG Service Manual......................................................................................Part No. 42526AENG Parts Catalog.........................................................................................Part No. 28907A Vehicle Moving and Transporting Instructions.......................................Part No. 42403AMUL

Tigercat 726E Feller Buncher

Introduction

iv

Tigercat 726E726E Feller Buncher Tigercat Feller

Buncher

Introduction

INTRODUCTION

An Operator's manual, Service manual and a Parts catalog are made available by Tigercat to assist the dealer, customer and operator in becoming familiar with the features of the 726E Feller Buncher serial number 7264001 to 7265000.

The 726E Feller Buncher is designed for harvesting trees, selective felling, thinning and final felling applications in plantations and natural stands.

The operator's manual will assist the operator with the techniques of proper and safe operation of the 726E Feller Buncher. There is also important information regarding the safe operation of the saw head.

The service manual contains safety and servicing procedures and a preventive maintenance schedule to assist in repair and to ensure optimum machine performance. For manual part numbers, see the title page in each manual.

Section 1 in both the operator's manual and the service manual contains safety information that must be followed. As well, throughout the rest of the manuals, WARNING and CAUTION notices are displayed where necessary, drawing attention to possible hazards when performing certain procedures.

Only trained personnel should be allowed to operate or work on the machine.

The information contained in this manual is current at time of printing. Improvements to the machine are on-going and may not be covered, therefore in these cases contact your Tigercat dealer for the appropriate information.

The phrase “and up” appearing in this manual after the serial number implies that the related information is current for any machine serial number HIGHER than the serial number preceding the “and up”.

Tigercat reserves the right to make changes to the machine after this manual release date that may not immediately appear in this manual.

Every effort is made to send out updates on a regular basis. If the machine in question was built after the release date of this manual and there is a discrepancy, call Tigercat service department. The release date appears on the first page.

The Company reserves the right to change information contained herein at any time without prior notice.

Tigercat Industries Inc.

M726E-DIM

v

Tigercat 726E Feller Buncher

Introduction

S.A.E. STANDARDS ROLL-OVER PROTECTION STRUCTURES (ROPS) FALLING OBJECTS PROTECTION STRUCTURES (FOPS) OPERATOR PROTECTION STRUCTURES (OPS) * MODIFICATIONS AND REPAIRS: The integrity of the ROPS, FOPS, OPS structure and its continued ability to provide the level of protection it was designed for could be seriously affected by any modifications to the structure, its mounting or to the chassis to which it is attached.

Tigercat emphasizes that the certification of approval of the ROPS, FOPS, OPS structure will become void if any such modification(s) take place.

Tigercat may officially grant approval for modifications only by: i. Written approval of repairs or modifications signed by the Tigercat Engineering Manager; or ii. Approved modifications officially released by Tigercat.

Both of the above are provided that the work is carried out in the factory approved manner.

Unauthorized modifications and/or repairs made or contributed to by a customer or a Tigercat distributor may result in creating a dangerous situation and therefore the customer or Tigercat distributor will be considered to have assumed the risk involved or be negligent in creating this situation.

Tigercat will not be held responsible for situations arising from having created unauthorized modifications/changes to the structure.

Operator's cabs are designed to ROPS, FOPS, OPS standards so that they will withstand force and absorb energy during a roll-over (ROPS), when resisting the impact of a falling object (FOPS) and minimize the posibility of operator injury from penetrating objects (OPS). When a permanent deflection of the structure occurs, the structure can no longer provide the original designed level of protection and should be replaced. Attempts to straighten the structure, particularly by the application of heat, can reduce still further the structures remaining capability to protect.

The mounting and the frame or chassis to which the cab is attached is considered an integral part of the ROPS, FOPS, OPS and is included in the design, test and certification of the product.

Contact the Tigercat Service department before attempting any modifications or repair to roll-over protective structures.

Tigercat Industries Inc.

vi

Tigercat 726E Feller Buncher

Introduction

NON-APPROVED FIELD PRODUCT CHANGES

The installation of any unauthorized attachment or changes made of any kind to this Tigercat product could affect the product's ability to perform as originally intended. The product's integrity, stability and it's ability to perform safely could be at serious risk.

IT IS Tigercat POLICY THAT NO CHANGES ARE TO BE MADE TO ITS PRODUCTS INCLUDING DELETIONS OR ADDITIONS OTHER THAN A Tigercat APPROVED OPTION FITTED IN THE FACTORY APPROVED MANNER. Official approval to make changes or install options is only to be undertaken as follows: i) The relevant options for that product must be shown or listed on current Tigercat documentation or literature such as a printed specification sheet, price list, parts manual, or product literature issued by Tigercat. ii) Approved options or product changes authorized in writing by the Tigercat Engineering Manager.

AUTHORIZATION BY ANY OTHER PERSON IS UNACCEPTABLE. Unauthorized changes made or contributed to by a person or organization may result in creating a dangerous situation and therefore the person or organization will be considered to have assumed the risk involved or be negligent in having created this situation.

Weight is an important factor when considering the addition of options or an attachment, Refer to your Tigercat distributor for information on maximum permissible operating weight and the effect the addition of various options may have on your machine.

Tigercat will not be held responsible for any situation that may arise resulting from Non-approved Field Product Changes to its product.

Should Tigercat become involved in a dispute resulting from changes made to the product without proper authorization by Tigercat as stated above, Tigercat will take whatever action is appropriate to protect its interests.

The product warranty policy and the certification on any safety items installed on the modified product will become NULL and VOID if the above policy is not adhered to as specified.

Non-approved product changes also nullify warranties given to Tigercat by its component manufacturers.

Tigercat Industries Inc.

vii

Tigercat 726E Feller Buncher

Introduction

viii

Tigercat 726E Feller Buncher SECTION 1 - SAFETY JANUARY, 2014

Read and understand this safety section prior to operating any equipment.

Read and understand all manuals for any attachments or accessories.

CONTENTS - SECTION 1 B

BACKOVER ACCIDENTS, AVOIDING....................................................................................................... 1.6 BATTERY DISCONNECT SWITCH......................................................................................................... 1.11 BATTERY SAFETY.................................................................................................................................... 1.6 BEFORE WELDING................................................................................................................................. 1.12 BOOM CYLINDER LOCK........................................................................................................................ 1.15 C

CAB EXITS.................................................................................................................................................1.8 D

DIESEL EXHAUST FLUID (DEF)............................................................................................................... 1.7 E

EMERGENCY CAB EXITS......................................................................................................................... 1.8 F

FELLING TREES......................................................................................................................................1.10 FIRE PREVENTION................................................................................................................................. 1.21 DRY CHEMICAL CLEANUP PROCEDURES....................................................................................... 1.25 FIRE PREVENTION GUIDELINES....................................................................................................... 1.21 WHAT TO DO AFTER A MACHINE FIRE HAS OCCURRED............................................................... 1.24 WHAT TO DO TO PREPARE FOR A MACHINE FIRE......................................................................... 1.22 WHAT TO DO WHEN A MACHINE FIRE OCCURS............................................................................. 1.23 FLUID INJECTION INJURY..................................................................................................................... 1.17 G

GENERAL SAFETY PRECAUTIONS........................................................................................................ 1.2 GREASE INJECTION INJURY................................................................................................................. 1.16 H

HOT FLUIDS AND HOT SURFACES....................................................................................................... 1.13 L

LIGHTNING SAFETY AWARENESS LIGHTNING SAFETY........................................................................................................................... 1.18 WHAT IS A LIGHTNING STRIKE?........................................................................................................ 1.18 LIQUID STARING AID................................................................................................................................ 1.7 P

PARKING THE MACHINE........................................................................................................................ 1.10 PROTECTIVE CLOTHING......................................................................................................................... 1.2 S

SAFETY HAZARDS, OPERATING............................................................................................................ 1.5 CAB EXITS.............................................................................................................................................1.8 REFUELLING......................................................................................................................................... 1.7 SAFETY INTERLOCK SWITCHES........................................................................................................ 1.8 SAFETY LABELS..................................................................................................................................... 1.26 SAFETY PRECAUTIONS, GENERAL....................................................................................................... 1.2 BACKOVER ACCIDENTS...................................................................................................................... 1.6 PROTECTIVE CLOTHING..................................................................................................................... 1.2 VITON SEALS........................................................................................................................................ 1.5 SAFETY PRECAUTIONS, OPERATING.................................................................................................... 1.7 LIQUID STARING AID............................................................................................................................ 1.7 SEAT BELT.............................................................................................................................................1.7 SAFETY PRECAUTIONS, SERVICING......................................................................................... 1.12, 1.18 SAFETY SYMBOLS................................................................................................................................... 1.2 SEAT BELT.................................................................................................................................................1.7 SIGNAL WORDS........................................................................................................................................ 1.2 V

VITON SEALS............................................................................................................................................ 1.5

Tigercat 726E Feller Buncher

Safety

GENERAL SAFETY PRECAUTIONS

SAFETY SYMBOLS

Remember that safety is a prime responsibility of all.

To minimize the risks and promote safety at all times, this section of the operator’s manual details a number of safety rules which should always be followed and obeyed.

This safety alert symbol means ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

Always read the operator's manual before operating the machine. Pay close attention to WARNINGS and HAZARD identifications.

The safety alert symbol identifies important safety messages on machines, safety signs, in manuals, or elsewhere. When you see this symbol, be alert to the possibility of personal injury or death.

Follow the instructions in the safety message.

Understanding Signal Words

DANGER

Follow all instructions from safety inspector and supervisors.

DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

You must be fully trained to operate this piece of equipment. Know the capabilities and the limitations of the equipment. Learn the most efficient operating techniques.

WARNING

Do not let untrained persons operate the machine.

WARNING indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.

Use recommended protective clothing and safety devices such as gloves, safety boots, safety hat, goggles, and ear protection when necessary.

These safety rules highlight both general and specific measures that the operator should be familiar with and adhere to. More specific measures are illustrated with pictograms which may also be attached to the machine in locations pertinent to their respective message. Keep safety labels in good condition. Repair or replace damaged labels.

1.2

Tigercat 726E Feller Buncher

Safety Always use the handrails and steps provided when mounting and dismounting from the machine.

KEEP BACK 150 m (500 ft)

Do not jump off the machine at any time.

When approaching an operating machine on foot, stay at least 150 m (500 ft) away until the operator recognizes your presence. Make sure that all equipment has been shut down before advancing to the machine.

Do not try to climb onto or off a moving machine.

Do not use the seat armrest or joystick as handles when entering or leaving the cab.

Do not use the machine foot controls as a step.

DANGER ROTATING SAW

When mounting or dismounting the machine always use the three point technique; Use one hand with two feet or two hands with one foot.

The safety of persons outside the cab is the responsibility of the machine operator

WARNING It is not recommended to walk on machine surfaces that are not designated walking areas.

No attempt should be made to walk on angled steel surfaces or surfaces that are irregular in shape.

Walking surfaces on the machine must be covered with anti-slip materials to provide a safe foot hold and prevent slipping.

Wear a suitable hearing protective device such as earmuffs or earplugs to protect against noise.

Prolonged exposure to loud noise can cause impairment or loss of hearing.

These anti-slip surfaces should be maintained on a regular basis. If the surface shows signs of wear, the anti-slip material must be replaced immediately.

WARNING Do not walk on machine surfaces with steel cleated foot wear. Steel cleats on steel surfaces are slippery and do not provide a safe foot hold.

1.3

Tigercat 726E Feller Buncher

Safety

Avoid mounting or dismounting the machine in areas with slippery surfaces. Dry, deice, clean up or cover slippery surfaces with an anti-slip material before mounting or dismounting the machine.

Keep a first aid kit in an easily accessible location on the vehicle at all times.

Working with oil Direct contact with oil implies a risk of skin complaints (example: eczema). Strict hygiene should always be observed.

To reduce the risk of fire, machines should be completely cleaned of debris at least daily, particularly around the engine exhaust components. Hydraulic oil leaks, excess grease, fuel and oil accumulation (including spillage) should be eliminated immediately, always shut off engine before cleaning machine.

Some advice which should be observed: • • • •

Maintain a clean cab interior, clear away trash or debris.

Machine should be washed completely at every major service.

• •

Inspect the machine daily for signs of damage or unusual wear to structures.

Check for fluid leaks, or faulty operation. Repair or replace malfunctioning parts and systems immediately.

• •

Check windows and door guards for damage.

• •

Check protective windows for cracks, a damaged window has reduced strength to stop flying objects. All damaged windows must be replaced with original equipment.

•

Check windows for scratching, crazing and cloudiness that could impair clear visibility all around the machine.

Oils used in this machine may be hot enough to cause serious burns.

Avoid contact with oil, particularly heated oil.

Oil on the skin should be washed off immediately with soap and water.

Wear protective gloves. Hands should be clean before putting on gloves. Apply protective cream to the hands to make washing easier.

Don't put oily rags in your pockets.

Oil soiled clothing should be changed as soon as possible.

Always keep an extra overall handy, but not in the machine where it can become dirty.

Cuts and abrasions must be attended to immediately. Clean them and apply first-aid.

Avoid breathing in oil fumes.

Wash hands and arms frequently (example: at each meal break or as often as possible).

Any cloths, residue and gloves must be safely discarded after use.

Read, understand and follow all general safety precautions specified by attachment manufacturer.

Do not operate the machine with any defective or inoperable components.

Check all fluid levels.

Do not operate the machine with any of the exhaust system, safety covers, or other devices removed.

1.4

Tigercat 726E Feller Buncher

Safety

Safety Hazards - Viton Seals O-rings and other seals manufactured of Viton material (fluorine rubber) produce a highly corrosive acid (Hydrofluoric) when subjected to temperatures above 315°C (600°F).

Maintain a distance of 3 m (10 ft) between the machine or boom and any power line carrying up to 50,000 volts or less plus 10 mm (½ in.) for each additional 1,000 volts above the 50,000 volt level.

If State/Provincial, local or job site regulations require even greater safety distances than stated above, adhere strictly to these regulations for your own protection.

This contamination can have extreme consequences on human tissue since it is almost impossible to remove after contact.

If the machine must be transported, make sure that it is adequately secured to the transporting vehicle. Refer to TRANSPORTING INSTRUCTIONS in SECTION 2 of the OPERATOR'S MANUAL.

The following procedures are recommended when inspecting equipment that has been subjected to high temperatures such as fire: •

Visually inspect any seals or gaskets which have suffered from heat; they will appear black and sticky.

•

If these are found, Do Not Touch!!!

•

Determine the material composition of any seals or gaskets. If fluoro-elastomer seals (Viton, fluorel, or tecmoflon) have been used, the affected area must be decontaminated before undertaking further work. Natural rubber and nitrile materials are not hazardous.

•

Disposable heavy duty gloves (neoprene) must be worn and the affected area decontaminated by washing thoroughly with limewater (Calcium Hydroxide solution).

•

Any cloths, residue and gloves must be safely discarded after use.

Even though the brakes are fully engaged, block the wheels to prevent movement during transport.

Install the articulation lock bar when ever the machine is to be transported.

Stopping the engine immediately after it has been working under load can result in overheating and premature wear of the engine components.

Reduce engine speed to LOW IDLE and let run for approximately five minutes to allow gradual dissipation of heat and also to reduce turbo speed. This will also prevent loss of coolant by after boil and possible hot spot damage to the engine.

NOTE: Burning discarded items is not recommended except in an approved incineration process where the dangerous products are treated by alkaline scrubbing.

Safety Hazards - Operating Maintain a charged fire extinguisher on the vehicle at all times and KNOW HOW TO USE IT.

Be aware when performing service and maintenance tasks that surfaces and grab handles in and around the engine and cooling system may become very hot when the engine has been running. Contact with hot surfaces may cause injury.

Do not carry passengers either in the cab or anywhere else on the machine. The vehicle is provided and approved with seating for the operator only.

Comply with instructions in this manual and also your company’s regulations for the operation of this machine.

Do not allow anyone to operate the machine who may not be physically fit or who may be under the influence of alcohol or drugs.

Read, understand and follow all general safety precautions specified by attachment manufacturer.

When moving the machine, watch that enough clearance is available on both sides and above the machine or any of its attachments. Extra clearance may be required particularly where the ground is uneven.

WARNING Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

Approach with extreme caution any area where overhanging electrical power lines are present.

Serious injury or death by electrocution can result if the machine or any of its attachments are not kept a safe distance from these lines.

1.5

Tigercat 726E Feller Buncher

Safety

WARNING

Avoid Injury from Backover Accidents Before moving machine, be sure all persons are clear of the area.

Battery posts, terminals and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

Wash hands after handling.

Always be alert for bystanders moving into the work area. Use horn to warn bystanders before moving the machine.

When using a signal person, keep the person in view at all times. Always be sure the signal person is clear before backing up.

If acid is accidentally splashed into your eyes, flush immediately with clean water and get medical attention.

To avoid backover accidents:

Do not attempt to charge a frozen battery; it can explode.

•

Disconnect battery before working on electrical systems as follows:

•

•

Turn off battery disconnect switch in battery compartment in RH rear of machine.

•

Disconnect negative starter motor cable from both battery posts.

•

Disconnect positive master solenoid cable from both battery posts.

• •

Connect ground terminal last when reconnecting.

•

Do not short out battery terminals for any reason.

Serious burns or an explosion can result.

•

CAUTION Lead-acid batteries contain sulphuric acid which can severely damage eyes or skin on contact. Always wear a safety face shield, rubber gloves and protective clothing to reduce risk of accidents.

Lead-acid batteries produce flammable and explosive gasses. Keep arcs, sparks, open flames and lighted tobacco a safe distance from the batteries.

1.6

Always look around before you back up. Be sure that everyone is clear.

Keep motion warning alarm in working condition. The motion warning alarm must sound when the machine is moving in forward or reverse.

Use a signal person when backing up if view is obstructed. Always keep the signal person in view.

Learn the meaning of all flags, signs and markings on the job site and who is responsible for signalling.

Keep windows, mirrors and lights in good condition.

Dust, heavy rain, fog, snow etc. can reduce visibility. As visibility decreases, reduce speed and use proper lighting.

Tigercat 726E Feller Buncher

Safety

OPERATING SAFETY PRECAUTIONS

41581AUNI R0

Shut off engine when refuelling - DO NOT refuel the engine while smoking or near open flame or sparks.

Diesel Exhaust Fluid (DEF) may irritate eyes or skin. Do not get in eyes. Do not get on skin.

First Aid treatment: DEF Contains Urea. If swallowed call a Poison Control Center or doctor immediately. Do not induce vomiting. If in eyes rinse with water for 15 minutes. If on skin rinse well with water. If irritation persists seek medical treatment.

Attach a grounding strap to an unpainted metal surface on the machine if the refuelling tank or nozzle is so equipped.

Check that no other personnel have moved into a hazardous area before starting the machine.

Sound the machine horn before starting the machine.

WARNING Use only diesel exhaust fluid (DEF) which meets ISO 22241 specifications. DEF fluid is sprayed into the exhaust system at high temperatures during normal operation of the Selective Catalytic Reduction (SCR) after treatment system.

NEVER fill the DEF tank with any other fluid.

Doing so may cause a fire risk which could result in death or serious injury.

The operator's seat is equipped with lap and shoulder harness belts. Use both of these restraint system at all times when operating the machine.

Start the engine by following the instructions in this manual. Refer to OPERATING MACHINE in SECTION 2 of the OPERATOR’S MANUAL.

WARNING • EXPLOSION HAZARD. • DO NOT USE ETHER. • ENGINE EQUIPPED WITH HEATER STARTING AID. • USE OF ETHER COULD RESULT IN DEATH OR SERIOUS INJURY. 36782BENG R0

Never use a liquid staring aid to start an engine.

Before moving the machine to the worksite, check to ensure that all doors, panels, and access covers are installed properly and secured.

1.7

Tigercat 726E Feller Buncher

Safety

CAB EXITS

SWITCH

There are three ways to exit the cab in case of an emergency.

1. Left door, this is also the main point of entry and is the only door that should be used under normal operating conditions to enter or leave the cab. This door is also equipped with a SAFETY INTERLOCK SWITCH. See SAFETY INTERLOCK SWITCH ON DOORS in THIS SECTION.

ACTUATOR

2. Right door, should be used for emergency exits only. Do not use this door to routinely enter or leave the cab. This door is also equipped with a SAFETY INTERLOCK SWITCH. ALWAYS shut OFF engine before using the right door exit.

M726E-020

INTERLOCK SWITCH (L.H. DOOR SHOWN) SAFETY INTERLOCK SWITCHES ON DOORS: Both doors are equipped with safety interlock switches to prevent the machine from being operated while either of the doors are open (pilot system is shut off).

3. Escape hatch, this is a third cab exit for use if the cab door exits become blocked.

This hatch is not equipped with a safety interlock switch and therefore when left open will not deactivate the pilot controls in the cab.

ALWAYS shut OFF engine before using the escape hatch exit.

CAUTION Safety interlock switches DO NOT lock out the steering function on machines equipped with a steering wheel.

It is important that the operator of the machine be familiar with these emergency exits and how to use them.

CAUTION DO NOT use the steering joystick to assist entering or leaving the cab.

All three exits should be checked to make sure that they are operational and will function in an emergency. The safety interlock mechanism on the cab doors and escape hatch retaining mechanisms must not be tampered with or defeated.

NOTE: The engine can be started but the machine functions cannot be operated with a door open.

To operate:

IMPORTANT! Unlock both doors before operating machine to allow opening from the outside in case of an emergency. Make sure that the doors are operational, open the doors twice, once using the exterior handle and once using the interior latch handle.

Close both doors and press the INTERLOCK RESET switch .

CAUTION All functions on the machine can now be operated, either as intended or by accidentally touching them.

For additional information, refer to EMERGENCY EXITS in SECTION 2 of the OPERATOR'S MANUAL.

Once the safety interlock system has been activated, the safety of both the operator and all persons outside the cab becomes the responsibility of the operator.

The door safety interlock switches and the pilot reset switch are a safety feature and their function must not be defeated in any way.

1.8

Tigercat 726E Feller Buncher

Safety

Machine operations should only be performed from the operator's seat.

Secure loose items in the cab.

Prior to commencing work, check all equipment controls to ensure that the machine responds correctly.

Make sure that all safety screens and guards including the skylight are installed and properly secured.

Maintain a safe operating distance between the machine and other personnel. Never operate the boom or attachment over the heads of bystanders.

Do not open an escape hatch or the cab doors to increase ventilation when operating the machine.

Keep the cab doors closed when driving or steering the machine to prevent accidental entry of branches and debris into the cab.

Do not turn on saw blade until machine is at cutting site.

Never travel near co-workers or other pieces of equipment with cutter turning.

Keep the cab doors closed and use seat belt when driving or steering the machine to prevent being thrown from the operator's cab.

Do not allow people or other pieces of equipment near the machine when saw blade in running or during operation.

Never use the parking brake to slow down or stop the machine except in an emergency.

Use only prearranged and approved signalling practices.

Keep the parking brake properly adjusted at all times.

Operate the machine only from a seated position in the operator’s seat.

Keep service brakes properly adjusted and check for proper operation of the service brake. Refer to SERVICE BRAKE ~ CHECKING BRAKE AND ACCUMULATOR FOR PROPER OPERATION in SECTION 3 of THIS MANUAL.

Watch for ground hazards such as metal debris, wire fencing or rocks.

When travelling position attachment and boom accordingly so as not to impair vision.

Always rest the attachment on the ground when operation is stopped, regardless if the engine is running or shut off.

If vision is limited by dust, smoke, fog, rain or snow, stop the machine until visibility is restored.

CAUTION Do not open cab doors or window screens when machine is on a slope. The doors and screens are heavy and could swing out with considerable force.

When working on slopes, travel straight up or down the slope to prevent roll-over.

When the engine is running, DO NOT allow anyone in areas of the machine where they may be crushed by moving components.

•

Do not run engine when persons are on steps or in doorway area.

•

Serious injury or death could result from crushing.

NEVER travel across a STEEP slope or side hill:

1.9

•

If you travel across a MODERATE slope, NEVER make an uphill turn as this could cause a tip-over situation.

•

As logs are added to the accumulator pocket the handling and the stability of the machine will change.

•

To avoid tip over, keep the felling head as low as possible to maintain a low center of gravity.

Tigercat 726E Feller Buncher •

Always be prepared to dump the load in case of an emergency.

•

Do not overload the machine as this can create an unstable condition and cause a rollover.

Safety Never use this machine to clear a logging deck on a new tract of timber when the rest of the equipment and operator's are also moving in.

Pre-plan to clear decks in advance before other equipment arrives.

Never work alone. Regularly inform other crew members of your intentions, location and length of time to perform duties.

FELLING TREES Pieces of wood, debris from the ground and even teeth separating from the saw blade become potentially dangerous missiles when thrown from these machines.

Stop the saw blade before leaving the cutting area. NOTE: The saw blade will continue to free wheel for several minutes after the saw switch has been turned OFF.

Inspect saw teeth, tooth retaining bolts, saw disc and felling head assembly.

To stop the blade from rotating, CAREFULLY lower the saw blade onto a stump. This should be done gently to prevent unnecessary loading of the saw blade, saw housing and bearings. Park machine at least 15 m (50 ft) away from other equipment and in a cleared area. In the event of a fire, this distance will minimize the chance of the fire spreading to other equipment.

Ensure that all saw tooth retaining bolts are at correct torque value.

Replace all worn saw teeth or rotate worn teeth to align unused cutting tips.

Always replace saw tooth retaining bolts when replacing saw teeth.

Inspect saw disc for stress cracks and that saw disc does not wobble due to worn saw shaft bearings.

Before leaving operator's cab, apply the parking brake and lower the attachment onto the ground.

If out of the operator's cab for an extended period shut the machine off.

When parking the machine: • Park on level ground.

Never start the machine if the saw blade has missing teeth, teeth retaining bolts or a bent saw disc.

Shut down machine immediately if vibration occurs during cutting.

•

Do not park on a hillside or incline.

Check that the saw discharge area is clear and undamaged.

•

Lower attachment onto level ground.

When moving from tree to tree with the saw blade turning, take care not to make contact with other vegetation or debris.

•

Engage the parking brake.

•

Stop the engine and release pilot system pressure by performing the following steps: 1. Close both doors. Turn key switch to ON position. Do not start the engine. Press pilot reset switch.

Do not over load felling head.

Work within your operating skills, do not attempt to cut down a tree that is too large for the felling head.

Complete either steps 2A or 2B. 2A. Fully apply brake foot pedal 50 times or more.

Operate so that the chip discharge area of the felling head is not directed at people, livestock, buildings or other machines.

2B. Turn rear differential switch ON and hold front differential lock switch ON for 30 seconds. While waiting, pump brake foot pedal at least 10 times.

When making the cut, properly position felling head in front of tree and have saw blade running at full rpm.

3. Pressure may remain in the system after completing all of the above steps.

Use caution when loosening hydraulic connections.

Always know and control the direction the tree will fall to prevent injury to co-workers or damage other vehicles.

When backing away from a cut, watch out for obstacles in your path.

Always travel with felling head as close to the ground as possible, never elevate the felling head unless necessary.

1.10

For additional information, refer to RELEASE PILOT SYSTEM PRESSURE in SECTION 5 of the SERVICE MANUAL.

Tigercat 726E Feller Buncher

620E-063

•

Safety

BATTERY DISCONNECT SWITCH

Turn the battery disconnect switch off if the machine is to be parked for an extended period of time (Example - overnight).

NOTE: This machine is equipped with an After Run/ Accessory Relay which delays, by 90 seconds, the power disconnect to engine related fuses and relays (ECU /ATS relay, NOx Sensor relay, NOx Sensor fuse, ECU Power fuse, DCU fuse). Whenever the engine is stopped all DEF solution is pumped back to tank before the engine power system is turned off. This process takes approximately 90 seconds. Refer to SELECTIVE CATALYTIC REDUCTION SYSTEM in SECTION 3 for more information.

When travelling on public roads, use accessory lights (when installed) and other cautionary devices to provide operators of other vehicles warning of your approach. Ensure your machine meets all regulatory requirements.

When transporting the machine watch that enough clearance is available on both sides and above the machine or any of its attachments to avoid contact with power or telephone lines, bridge structures, etc.

Before transporting the machine check to ensure that all doors, panels and access covers are installed properly and secured.

1.11

Tigercat 726E Feller Buncher

Safety Prior to welding on any part of the machine, it should be cleaned and a fire extinguisher should be made available at the welding location. Care must be taken in attaching the welding machine grounding clamp so electrical current does not pass through bearings.

SERVICING SAFETY PRECAUTIONS

This machine is equipped with sensitive electronic control equipment, prior to welding:-

Conduct maintenance inspections at least as frequently as recommended in SECTION 3 of THIS MANUAL. When servicing or repairing equipment, shut the engine down, and disconnect the negative (-) battery cable from both batteries.

620E-063

BATTERY DISCONNECT SWITCH

Turn Battery Disconnect Switch to the OFF position and disconnect the positive (+) battery cable from both batteries.

Install a “DO NOT START ENGINE” sign on the operator’s cab door and in the engine compartment when making repairs to the machine.

ENGINE "CPU" MODULE MULTI-PIN CONNECTORS

Before performing maintenance or repair work on any equipment, consult the manufacturer’s instruction manual and follow recommended procedures.

M726E-118

MULTI-PIN CONNECTOR

DISCONNECT CPU HARNESS

Disconnect the engine CPU (Central Processing Unit) and engine wiring harness by unplugging the multi-pin connectors.

The charge air cooler, radiator and the engine cooling system should be cleaned and serviced at least daily to maintain moderate engine temperatures.

WARNING This machine is equipped with a reversible cooling fan. Exercise care when working in this area with the engine running.

This machine is equipped with a reversible cooling fan to facilitate cleaning of the charge air cooler, radiator and oil cooler assembly. Exercise care when working in this area with the engine running. If the fan switch in the cab is in the AUTO position, the fan could turn ON and/or go into REVERSE mode without warning.

1.12

Tigercat 726E Feller Buncher

Safety

WARNING Diesel fuel or hydraulic fluid under pressure can penetrate the skin and cause serious personal injury, blindness, or death. If any fluid is injected into the skin, it must be surgically removed within a few hours by a doctor familiar with treating this type of injury.

Explosive release of fluids from pressurized cooling system can cause serious burns.

Never use bare hand to check for fluid leaks.

Shut off engine. Only remove filler cap when cool enough to touch with bare hands. Slowly loosen cap to first stop to relieve pressure before removing completely.

Fluid leaks under pressure may not be visible.

When searching for leaks, wear work gloves and use a wrench or piece of wood to move hydraulic hoses. Do not grab hold of hydraulic hoses.

Wear safety goggles for eye protection.

Do not change any pressure or relief setting unless authorized instruction has been obtained.

Use the proper tool for the job. Repair or replace worn or damaged tools including lifting equipment immediately.

WARNING

Pressure can be maintained in a hydraulic system long after the power source and pump have been shut down. Lower the attachment to the ground, stop engine and relieve trapped pressure from pilot system and brake accumulators before performing work on components, or disconnecting any hoses. For the procedure on how to RELIEVE PRESSURE, refer to PARKING THE MACHINE in THIS SECTION.

WARNING, HOT FLUIDS AND HOT MACHINE SURFACES CAN CAUSE SERIOUS BURNS!

1.13

•

Before servicing the machine, allow the engine cooling system, fuel system, exhaust system, hydraulic system and machine surfaces to cool down.

•

Use a thermometer to check surface and system temperatures to ensure it is safe to begin service work.

•

DO NOT begin service work until the surface or system temperature has cooled down to below 100°F (38°C)!

Tigercat 726E Feller Buncher

Safety

Keep your hands, feet, head, and loose clothing away from power driven parts. Tie long hair behind your head. Remove rings and other jewelry to prevent electrical shorts and entanglement in moving parts.

CAUTION Do not open cab doors or window screens when machine is on a slope. The doors and screens are heavy and could swing out with considerable force.

WARNING Failure to follow all of the above instructions could result in serious injury or death from crushing.

CAUTION Always be aware of machine pinch points that could cause injury. Never place body parts within the range of motion of the working parts of the machine.

FRONT CHASSIS

The lower access panels are NOT HINGED or permanently attached to the machine, but are held in place by the UPPER DOORS. Therefore they can fall during the process of removing them from the machine. Once the UPPER DOOR is opened the LOWER PANEL is not fully supported and it is not safe to apply any weight or pressure to the panel, as it may fall out of the remaining supports. Do not use these LOWER PANELS as hand grips, when servicing the machine.

REAR CHASSIS

RETAINING PIN

LYNCH PIN LOWER PANELS

LOCK BAR

726D-039

LOCK BAR IN LOCKED POSITION

To prevent accidental articulation of the machine and injury when working in the center joint area, install the frame articulation lock bar between the frames and hold in place with the lynch pins provided.

Never stand under an object supported with hydraulics. Always use safety stands or a locking device.

M726E-065

LOWER PANELS

WARNING DO NOT work below or behind a machine that is parked on a grade.

WARNING Always allow the saw blade to come to a COMPLETE STOP before approaching attachment to make adjustments.

M726E-064

1.14

Tigercat 726E Feller Buncher

Safety

LIFT BOOM CYLINDER LOCK

LIFT BOOM

Before performing work under the attachment or lift boom, ensure that the attachment is firmly supported on level ground, on solid stands or, install lift boom cylinder lock.

CYLINDER

'T' HANDLE

726E-073

LIFT BOOM CYLINDER LOCK IN LOCK POSITION

Completely raise lift boom and place lock over one of the two cylinder rods with the open side facing down and wide end against the cylinder gland. Install 'T' handle retaining bolt through center hole.

Do not place yourself under the boom or attachment, while doing this. Do not damage the piston rod when installing the boom lift lock. Turn off the engine, turn key back to RUN position, press the INTERLOCK RESET switch to activate the pilot oil system.

SLOWLY lower the boom until the boom lift lock is securely in place.

CYLINDER LOCK

INTERLOCK RESET SWITCH

726E-079

CYLINDER LOCK STORAGE

The lift boom cylinder lock is stored on the inside of the hydraulic pump compartment door.

WARNING

M726E-044

Always install lift boom lock before working on or around machine with boom raised.

• Always install 'T' handle retainer bolt • Use only to support boom and attachment.

CONTROL PANEL

To remove the boom lift lock, start the engine, press INTERLOCK RESET switch and raise the boom completely. Without placing yourself under the boom or attachment, remove the 'T' handle retainer bolt, remove the boom lift lock and reinstall it on the inside of the hydraulic compartment door.

1.15

Tigercat 726E Feller Buncher

Safety GREASE INJECTION INJURY WHEN USING PNEUMATIC GREASE GUNS Pneumatic grease guns can deliver grease at pressures from 17 - 400 Bar (246 - 5801 psi).

It takes less than 7 Bar (100 psi) to inject a substance through human skin.

ALWAYS get professional medical treatment immediately after any type of injection injury.

Provide the physician with information on the type of grease, the pressure setting of the gun, and similar details.

If the engine is running inside a building, ensure that sufficient ventilation is available to prevent a buildup of toxic exhaust fumes. Run the engine only when it is necessary for testing or adjustments.

The amount of fluid injected, type of fluid (or material), pressure at which it was injected, and the elapsed time between injection and surgery all influence the chances of successful treatment for this type of serious injury.

Work in a ventilated area. If it is necessary to run an engine in an enclosed area, use an exhaust pipe extension to remove toxic exhaust fumes.

Prior to using a high pressure pneumatic grease gun perform the following:

If you don't have an exhaust pipe extension, either work outside, or open the shop doors.

Dispose of fluids properly.

Do not pour fluids into the ground, stream, pond or lake.

Before draining any fluids, know the proper way to dispose of them.

1.16

•

All operators of high pressure pneumatic grease guns MUST be trained in the hazards of its operations and the treatment for such injuries.

•

DO NOT OPERATE a high pressure pneumatic grease gun unless you have been trained in the proper operation and are aware of all safety precautions of such a tool.

•

Wear protective clothing such as gloves, safety hat and safety glasses.

•

Inspect all parts of the grease gun for wear and tear and replace all worn or damaged parts.

•

Ensure that protective shrouds are installed on all grease gun nozzles as safety devices.

•

Remove dirt and grease from grease fittings prior to greasing.

•

Replace any defective grease fittings on equipment with new fittings immediately.

•

When badly positioned fittings are identified, replace them with angled or swivel fittings for easier access.

Tigercat 726E Feller Buncher

Safety

FLUID INJECTION INJURY

WARNING

Hydraulic and diesel fuel systems on forestry machines operate at very high pressures, often 207 bar (3000 psi) and above. If a loose connection or a defect in a hose should occur, a fine, high velocity stream of fluid will result. Even for systems pressurized to as little as 7 bar (100 psi), this fluid stream can penetrate human skin as if it were a hypodermic needle.

Diesel fuel or hydraulic fluid under pressure can penetrate the skin and could result in death or serious injury. If any fluid is injected under the skin, a medical doctor familiar with the treatment of this type of injury must surgically remove it within a few hours.

In the event of any suspected fluid injection injury • Report the injury to your supervisor immediately.

• Seek professional medical attention immediately.

As always the best defence against suffering the effects of fluid injection is to prevent the accident from occurring in the first place.

When searching for possible fluid leaks • Never search for leaks with your bare hands.

Always wear thick protective gloves.

• Be sure to wear safety goggles for eye protection.

• Keep all body parts well away from the area being investigated for leaks.

• Use the end of a long piece of wood to move hoses or other obstacles.

Initially, an accidental fluid injection beneath the skin may only produce a slight stinging sensation.

There is a danger that you will tend to ignore this, thinking that it will get better with time. Most often, it does not! Within a very short time the wound may begin to throb painfully, indicating that tissue damage has already begun.

Similarly fluid injected directly into a blood vessel can spread rapidly through your circulatory system. The human body has little ability to purge injected fluid.

Diesel fuel or hydraulic fluid under pressure can penetrate the skin and could result in death or serious injury. If any fluid is injected under the skin, a medical doctor familiar with the treatment of this type of injury must surgically remove it within a few hours.

•

Place the end of a long piece of wood in the suspected path of any fluid stream. Never use any part of your body.

• Recognize that the source of the leak and the fluid streaming from it may be very small and not easily visible. You may only be able to see the fluid that accumulates as a result of the fluid stream.

When performing any service work • Stop the engine and relieve all diesel fuel or hydraulic pressure before disconnecting any lines or otherwise working on the system.

• Never grab any hydraulic or diesel fuel connectors or hoses when they are subjected to pressure.

• Always ensure that hoses are rated for the pressures to which they will be subjected.

• Never use any hoses that you suspect could be defective.

Time becomes critical as tissue damage progresses rapidly. The longer you delay getting professional medical attention, the more damage can occur.

Although fluid injection accidents are rare, the resulting injury has on occasion required the amputation of a finger, a hand or in some cases the entire limb. The longer the delay in getting professional medical aid, the further up the limb the tissue damage can spread. An injury of this type can become very serious or even fatal if not dealt with promptly and properly.

1.17

Tigercat 726E Feller Buncher

Safety LIGHTNING SAFETY

LIGHTNING SAFETY AWARENESS

In spite of the popular myth that being struck by lightning is an unlikely event, the facts show that lightning strikes occur frequently. As a result loggers are at high risk because their work is outdoors and close to known strike points such as tall trees and heavy equipment.

Loggers can increase their chances of avoiding a lightning strike by following a few simple safety practices.

1. Designate a member of your crew to

WHAT IS A LIGHTNING STRIKE? Lightning is a discharge of the electricity produced by a thunderstorm. As the thunderstorm develops, many small particles of ice within the storm clouds bump together. These collisions create a positive charge at the top of a cloud and a negative charge at the bottom. As this continues a second positive charge builds up on the ground beneath the cloud, concentrated around high objects such as hills, trees, buildings, equipment and even people.

•

Monitor daily weather forecasts

•

Observe local weather conditions

•

Alert all other members of the crew when a possible lightning threat develops.

2. Don’t start or continue any work that cannot be stopped immediately, when a storm moves nearby.

3. Anticipate a high-risk situation and take action early by moving to a low-risk location. Do not hesitate. If there is lightning, you are in danger.

When the difference between the electrical charge in the cloud and on the ground becomes great enough to overcome the resistance of the insulating air between them, an electrical current flows instantly. This is a lightning strike.

4. Obey the rule - If you see lightning, Flee. If you hear thunder, Clear.

5. Do not follow the now obsolete guideline to take shelter when the time between seeing lightning and hearing thunder is 30 seconds or less. This does not provide sufficient time to ensure safety. Always follow step 4.

The electrical potential in a lightning strike can be as much as 100 million volts. Lightning strikes can occur over very large distances, even as much as 60 km (37 miles). Lightning travels both in front of and behind a thunderstorm and so strikes happen even when rain has not started or has stopped.

Lightning can hit in the same place, many times and often spreads out over 18 m (60 feet) within the soil around the strike point.

6. Remain in your safe location for 30 minutes after the last sight of lightning or the last sound of thunder.

The safest location during lightning activity is inside a fully enclosed, substantially constructed building, a house, office, school, shopping area, etc. These are the safest because of the electrical wiring and plumbing that they contain. Should lightning strike, the electrical current will travel through the wiring or plumbing into the ground.

When such a building is nearby, always seek shelter there first.

Thunder always accompanies lightning. When lightning occurs, the air through which it travels is instantaneously heated to a temperature more than 28,000°C (50,000°F). The air expands rapidly due to this heating, then quickly contracts as it cools. It is this contracting shock wave that we hear as thunder.

In many areas of the world, lightning strikes are second only to flooding as the greatest cause of storm related deaths and injuries. Although only 10% of lightning strike victims are killed, virtually all from cardiac or respiratory arrest, over 70% of those that survive suffer severe, life-long injury and disability. The symptoms of a lightning strike include memory loss, fatigue, chronic pain, dizziness, sleeping difficulty and the inability to complete several tasks at one time.

1.18

Tigercat 726E Feller Buncher

Safety WHAT TO DO IF YOU ARE OUTSIDE AND SEE LIGHTNING OR HEAR THUNDER.

Unfortunately loggers do not often work close to buildings and therefore other alternatives need to be considered.

If you can, get inside.

Sheds, weather shelters, hunting blinds, tents and other partially open or small structures are not safe against lightning strikes as they lack the electrically grounded components of larger buildings. They are intended for sun or rain protection only. Do not seek shelter from lightning strikes inside these structures.

1. Run to the nearest building, motor vehicle or fully enclosed ROPS equipment cab immediately. Being anywhere outside is not safe.

2. If inside a building:

The second safest location during lightning activity is inside a fully enclosed car, van, truck or bus with a metal roof and metal sides. The electrical energy of a lightning strike to these vehicles is carried to ground by the conducting outer metal surfaces. This is called the skin effect.

Do not seek safety from lightning strikes in vehicles with fiberglass or plastic body shells or in convertible top vehicles. None of these are safe, as they do not offer skin effect lightning protection.

•

Don’t watch the lightning storm from open windows or doorways. Stay in inner rooms.

•

Stay well away from corded telephones, electrical appliances, lighting fixtures, radio microphones, electrical sockets and plumbing pipes and fixtures.

3. If inside a motor vehicle or fully enclosed ROPS equipment cab:

Heavy forestry equipment such as a skidder, loader, feller buncher, forwarder, etc. with a fully enclosed rollover protective structure (ROPS) cab take advantage of the skin effect and are therefore safe in electrical storms.

However machines with a rollover canopy only are not safe against lightning strikes as they are open to electrically conductive rainwater and do not benefit from the skin effect. Operators of this equipment must abandon their machines and get to a safer location before lightning strikes.

Note that the rubber tires on motor vehicles and heavy equipment do not increase safety from lightning strikes. Lightning has already travelled a great distance through the air to strike the vehicle.

In comparison a few inches of rubber in a tire offers absolutely no additional insulation.

1.19

•

Under no circumstances whatsoever step outside of the vehicle or off the equipment to move to another shelter. Very dangerous electrical pathways to ground may go through you.

•

Shut down all operation, turn off the engine, close all doors and raise all windows.

•

Sit squarely in the seat with your hands in your lap and your feet flat on the floor mat.

•

Do not touch any metallic objects referenced to the outside of the vehicle.

Do not touch any door and window handles, control levers, foot pedals, steering wheels, cab interior walls and any other inside to outside metal objects.

•

Do not touch any radio or telephone connected to an outside antenna.

Tigercat 726E Feller Buncher

Safety

If you are caught outside and have no where else to go.

What to do if you feel your skin tingling, your hair stands on end, light metal objects vibrate or you hear a crackling sound.

1. Avoid wide-open areas where you project above the surrounding landscape.

1. Lightning is probably about to strike. You only have a few seconds to act.

2. Seek shelter in a low place, such as a ditch, ravine, valley, canyon or cave.

2. Put your feet together. Crouch down like in a baseball catcher’s position. Hold your head down. Cover your ears to protect them against the noise of the thunder.

3. Get away from open water such as ponds or streams.

4. Do not take shelter under any isolated tall trees or small groups of trees.

3. Do not lie flat on the ground. By touching as little of the ground as possible, the lightning may not move across the ground to you.

5. Seek shelter amongst the dense, thick growth of the shortest trees.

What to do if a co-worker has been struck by lightning.

6. Avoid entering any small enclosures or shelters.

1. The victim does not carry any electrical charge. There is no danger to anyone helping this person. You can touch him or her immediately.

7. Do not seek shelter under any motor vehicle or heavy equipment.

8. Keep clear of any materials that can conduct electricity such as wire fences and gates, metal pipes, poles, rails and tools.

2. Call your local emergency response telephone number immediately.

9. Stay at least 15m (50 feet) away from metal objects such as a fuel tank, a vehicle or machinery without a cab, motorcycle, ATV, etc.

10. Stay at least 5m (16 feet) apart from any other members of a group so that lightning won’t travel between you.

11. Do not use the telephone except for emergencies.

3. If the victim has no pulse, their heart has stopped or they have stopped breathing, start cardiopulmonary resuscitation (CPR) or mouth –to-mouth resuscitation immediately. Use a portable defibrillator if one is available.

4. Be careful about staying in the storm to take care of the victim. You can get hit by lightning too. If you can, move the victim to a building as soon as possible.

To further increase your awareness about lightning safety, see the following web sites.

National Weather Service Lightning Safety http://www.lightningsafety.noaa.gov National Lightning Safety Institute http://www.lightningsafety.com

1.20

Tigercat 726E Feller Buncher

Safety 4. Clean out all accumulated forest debris (twigs, pine needles, branches, bark, leaves, saw dust, small wood chips) and any other combustible materials from inside the machine belly pans or lower machine structures as well as from areas in proximity to the engine, fuel and hydraulic oil systems no less frequently than at the completion of each work shift.

FIRE PREVENTION

When working in a forest environment, it is impossible to prevent combustible debris from collecting in tight corners of the machine. This debris, in itself, may cause a fire; however, when mixed with fuel, oil or grease in a hot or confined place, the danger of fire is greatly increased.

The following fire prevention guidelines should be used to supplement the operator’s fire prevention efforts. In no case should the guidelines be used, or assumed, as replacements for diligent operator efforts at preventing fires.

The following guidelines will help to keep your equipment up and running efficiently and keep the risk of fire to a minimum.

1. Maintain a CHARGED fire extinguisher on the machine at all times and KNOW HOW TO USE IT. 2. Remove debris and blow out dust regularly from the air intake doors, engine radiator and charge air cooler, hydraulic oil cooler, diesel fuel cooler and air conditioning condenser core to prevent overheating of the engine and hydraulics and to maintain efficient operation of the machine. Refer to CLEANING A/C CONDENSER, OIL COOLER AND RADIATOR in SECTION 2 of the OPERATOR’S MANUAL. 3. Blow off all forest debris and fine organic material accumulated near hot engine exhaust components (turbocharger and exhaust manifold as well as exhaust pipes and muffler) at the completion of each work shift or more frequently when working in logging conditions where large amounts of combustible forest debris are present.

Visual inspection after blow off to ensure thorough cleanliness is vital. Engine exhaust systems provide numerous small pockets where saw dust, small wood chips and other flammable forest debris can gather. Even small accumulations close to hot exhaust components can ignite and smolder. If dislodged this smoldering debris can fall into other areas of the machine and thereby spread a fire.

5. Inspect the machine regularly for any signs of diesel fuel or hydraulic system leakage.

Check for worn or eroded fuel or hydraulic lines before starting up any equipment.

6. Clean up any grease, diesel fuel, hydraulic and lubricating oil accumulation and spillage immediately.

7. Steam clean the engine, transmission, brake, fuel and hydraulic tank compartments of all equipment at least once a month or more frequently when working in logging conditions where large amounts of combustible forest debris are present.

8. Use only nonflammable solutions for cleaning the machine and components.

9. Inspect the exhaust system daily for any signs of leakage. Check for worn, cracked, broken or damaged pipes or muffler. Also check for missing or damaged bolts or clamps.

Should any exhaust leaks or defective parts be found, repairs must be made immediately.

Engine exhaust leaks can cause fires. Do not operate the machine until the exhaust leak is repaired.

10. During daily operation of the machine, the occurrence of exhaust leaks are usually accompanied by a change or increase in engine exhaust noise levels. These audible warnings cannot be ignored. Should any exhaust leaks occur during operation, the machine must be shut down immediately and not put back to work until the necessary repairs have been completed.

11. Park the machine at least 50 feet away from other equipment at the end of each shift.

12. Never leave the machine parked with boom, arch or blade suspended off the ground. Should their supporting hydraulic hoses burn through during a fire, pressurized hydraulic oil may be injected into the fire and the boom, arch or blade will fall rapidly to the ground.

1.21

Tigercat 726E Feller Buncher 13. Turn the battery disconnect switch to OFF at shut down to de-energize all electrical circuits.

14. Remain with the machine for at least 45 minutes at the end of operations while the machine cools.

Safety 17. AFTER transporting (trucking) a machine from one job site to the next, open all doors and access panels and blow off any debris that may have repositioned itself onto the engine and exhaust parts due to wind turbulence caused by the journey.

18. Before starting repair work, such as welding, the surrounding area should be cleaned and a fire extinguisher should be close by.

19. Store rags and other combustible materials in a safe, fireproof location.

20. Do not use the machine on top of or to push piles of burning timber. A machine fire will most probably result.

EQUIPMENT FIRES ADVERSELY EFFECT YOUR ABILITY TO LOG, MAY INCREASE YOUR INSURANCE PREMIUMS DRAMATICALLY OR PREVENT YOU FROM OBTAINING INSURANCE COVERAGE AT ALL. WHAT TO DO TO PREPARE FOR A MACHINE FIRE

15. Remove all keys, lock equipment and fuel cap at the end of operations to reduce the risk of vandalism.

•

Prevent the fire from happening in the first place by ensuring that all machine systems are frequently inspected and always well maintained.

•

Ensure that any hand held fire extinguishers are charged and in working order. Fire extinguishers require routine care. Follow the manufacturer’s instructions for inspection and maintenance shown on the label of the fire extinguisher and in the extinguisher manufacturer's manual.

•

Ensure that any pressurized water systems on the machine (if applicable) are charged and in working order. Refer to PRESSURIZED WATER SYSTEM MAINTENANCE in SECTION 3 of the OPERATOR’S MANUAL.

•

Ensure that you have the proper fire extinguishers on site. Most fires involving mobile forestry equipment will be Class A or B. Dry chemical extinguishers should be rated ABC and pressurized water extinguishers should be rated A. Class A fires involve ordinary combustibles such as wood, cloth, paper, rubber and many plastics, Class B fires occur with flammable liquids such as diesel fuel, oil and grease and Class C fires apply to energized electrical equipment.

16. Be cautious when smoking. An open flame, a lighted cigarette, etc., should not be permitted around any vehicle, especially during fuelling operations or when the fuel system is open to the atmosphere or when servicing batteries.

1.22

Tigercat 726E Feller Buncher •

•

•

• •

•

•

Ensure that the nozzle of any hand held extinguisher and pressurized water system available on the machine and at the work site fits within the access holes in the doors of the machine.

Ensure that your fire detection system* is in working order. Refer to FIRE DETECTION SYSTEM in SECTION 2 of the OPERATOR’S MANUAL. Ensure that your fire suppression system** is charged and in working order. Refer to FIRE SUPPRESSION SYSTEM in SECTION 2 of the OPERATOR’S MANUAL. Ensure that you are familiar with the recommended procedures for fire contained in the emergency action plan of your company.

Ensure that you follow all national, state / provincial and local regulations dealing with fire fighting in effect in your specific geographic region. Regulations will vary from region to region but most will usually require that: 1. Workers assigned to fire fighting duties must be physically capable of performing them safely and effectively.

2. Workers designated to use fire fighting equipment as part of an emergency action plan must receive full and proper training from a qualified instructor.

3. Whenever portable fire extinguishers are provided for use in the workplace, training must be provided to familiarize workers with the general principles of fire extinguisher use and the hazards involved with fire fighting.

4. Training must be provided upon initial employment and at least annually thereafter.

Ensure that after you have received the training as outlined above, that you know how to use the fire extinguisher, the pressurized water system (if applicable) and the fire

Safety WHAT TO DO WHEN A MACHINE FIRE OCCURS •

If operating the machine when a fire occurs: 1. Lower all working attachments to the ground.

2. Shut the engine off.

3. Activate the fire suppression system**.

4. Radio or call for help. Be certain to report a fire immediately.

5. Exit the machine taking fire extinguisher and pressurized water system hose (if applicable) with you.

6. At all times ensure your own personal safety and the safety of anyone that may be in the area. Approach any fire with extreme caution. All fires can be very dangerous and life threatening.

7. Only if you can safely do so, turn OFF the battery disconnect switch.

•

Before deciding to fight the fire, be certain that: 1. The fire is small and not rapidly spreading.

2. There is always a clear, safe escape route to your back.

3. You have received training in the use of the available fire extinguishing systems and are confident that you can operate them effectively.

•

Be aware that engine coolant , diesel fuel or hydraulic hoses could fail during a fire. If this happens, hot coolant, fuel or oil could possibly be ignited by the fire.

•

If in any doubt about whether or not to fight the fire – DON’T. Instead stand well clear of the fire and wait for help to arrive.

•

If possible a dry chemical fire extinguisher or

suppression system** on your machine.

There is not enough time available to read instructions during a fire emergency.

Ensure that all information necessary for you to immediately contact all sources of help (local fire department, etc) in the event of a fire emergency is recorded and readily available at all times.

1.23

fire suppression system** should be used first to fight a machine fire. Then immediately afterwards use the pressurized water hose supplied with the machine (if applicable) or a pressurized water extinguisher (if available). A fire suppressed by dry chemical may re-ignite from the heat retained by any debris in the area. The water will cool the area, reducing the chances of re-ignition.

Tigercat 726E Feller Buncher •

Safety

Use the PASS method. This is the most effective use of a fire extinguisher.

•

•

•

•

WHAT TO DO AFTER A MACHINE FIRE HAS OCCURRED

Pull the pin at the top of the extinguisher that keeps the handle from being pressed.

Break the plastic seal as the pin is pulled.

•

Before returning the machine to work.

1. Ensure that the cause of the fire is determined and all appropriate repairs are completed.

Aim the nozzle at the base of the fire. Do not aim the nozzle at the flames. In order to put out the fire, you must extinguish the fuel, not the flames. Hose nozzles are often clipped to the extinguisher body.

Release the hose before taking aim.

2. Ensure that the fire detection system*

or the fire suppression system** is properly serviced and in working order (if applicable).

Squeeze the handle to release the pressurized extinguishing agent. The handle can be released at any time to stop the discharge.

3. Ensure that all extinguishers used in fighting the fire are replaced or recharged.

•

Sweep from side to side at the base of the fire until the fire is completely out or the fire extinguisher is empty

Notify your equipment dealer and / or Tigercat Industries Inc. by completing an incident report, Tigercat form number 5101.

*NOTE: Fire detection systems are offered by

Tigercat as an optional installation on some Tigercat product lines. Please disregard any references made to fire detection systems if not installed on your machine.

**NOTE: Dry chemical fire suppression systems

are offered by Tigercat as an optional installation on some Tigercat product lines. Please disregard any references made to fire suppression systems if not installed on your machine.

20229A

• • •

• •

TYPICAL FIRE EXTINGUISHER ACCESS HOLE

Place the nozzle of the fire extinguisher into the appropriate fire extinguisher access hole and discharge the extinguisher.

Only if you can safely do so, open the access panels to the machine in the area of the fire.

Failing all attempts to access the machine compartment, discharge the extinguisher through the mesh or any available openings on the machine.

Ensure that the machine and all components have cooled down sufficiently after a fire so that re-ignition does not occur.

Remain with the machine until help arrives.

1.24

Tigercat 726E Feller Buncher DRY CHEMICAL CLEANUP PROCEDURES Both ABC dry chemical fire extinguishers and fire suppression systems discharge a chemical powder to extinguish the fire. The chemical makeup and the small particle size of the powder as well as the force of the discharge all contribute to the fire fighting capability. These same characteristics also permit the powder to penetrate into and fully cover all components in the vicinity of the discharge.

Safety 3. In areas exposed to heat during the fire, the dry chemical powder will melt forming a coating that cakes or crusts on all surfaces.

To break down the caked dry chemical, spray or wash these areas with a 50/50 mixture of hot water and isopropyl alcohol. Allow this mixture to stand in place for several minutes.

The caked dry chemical when exposed to moisture is also mildly acidic. Therefore when the break down procedure has been completed, follow this immediately with the neutralizing procedure as described in step 2.

The following are recommendations for the cleanup and neutralizing of areas exposed to dry chemical powder.

Workers performing this work should wear protective clothing, safety goggles and a fine particle dust mask to minimize their personal exposure to the dry chemical powder.

Ensure that all electrical systems have been completely de-energized prior to any cleanup.

1. In areas of the machine that remained cool and dry during the fire, the dry chemical will stay in powder form.

Be certain to clean these areas immediately to prevent any settled residual powder from coming into contact with moisture whether through direct contact or humidity in the air.

Remove the powder residue by blowing off with air, sweeping, dusting or vacuuming using a HEPA filter capable of trapping the small dry chemical particles. Then wipe all surfaces with a damp cloth.

2. In areas exposed to moisture, the dry chemical powder will combine with water to form a paste that is mildly acidic. Note that all surfaces covered by this dry chemical paste including electrical contacts are vulnerable to corrosive attack.

To neutralize the acidic paste on large surfaces, spray or wash these areas with a mixture of 3 parts hot water to 1 part baking soda. Allow this mixture to stand for several minutes before rinsing with warm water. Wash the area with a mild soap and water solution.

Rinse thoroughly with water. Blow-dry to remove all residual water.

Cleaning of electrical contacts should be done using an electrical contact cleaner that has no flash or fire point and is non-corrosive and non-conductive such as CRC Contact Cleaner 2000.

1.25

Tigercat 726E Feller Buncher

Safety OPERATOR'S MANUAL LOCATION

SAFETY LABELS SAFETY LABELS CAB LABELS The following safety labels are installed in the cab.

These labels are located inside the cab in full view of the operator. All labels must be periodically cleaned and inspected to ensure legibility is maintained. Replace any label that becomes illegible, damaged or removed.

This label indicates the storage location of the operator's manual. This label is located on the outside of the operator's manual case inside the cab.

READ OPERATOR'S MANUAL

USE SEAT BELT

Always read the operator’s manual before operating the machine. Pay close attention to WARNINGS and HAZARD identifications.

USE SEAT BELT. The seat belt supplied with this seat must be used at all times when operating this machine.

Study all the safety messages in this manual and on the labels on the machine carefully.

1.26

Tigercat 726E Feller Buncher

Safety

NO RIDERS

REMOVE IGNITION KEY BEFORE SERVICING THE MACHINE!

NO RIDERS INSIDE OR OUTSIDE OF THE MACHINE . Do not carry passengers either in the cab or anywhere else on the machine. The vehicle seating accommodation is for one operator only.

Persons riding on the outside of the machine are subject to hazards such as falling off the machine, crush hazards, thrown object hazards and many other hazards WHICH COULD RESULT IN DEATH OR SERIOUS INJURY.

Prior to performing any service work or maintenance on the machine, stop the engine, REMOVE THE IGNITION KEY and store it in a safe place.

If any person attempts to climb onto the machine during operation, STOP THE MACHINE IMMEDIATELY. Do Not Operate the machine until other personnel are a safe distance away from the machine.

1.27

Tigercat 726E Feller Buncher

Safety

EMERGENCY EXIT, CAB, RIGHT-HAND SIDE DOOR

CHECK DAILY

This label is located on the right-hand cab door post next to the door, alerting the operator that, in the event of an emergency this door can be used as an emergency exit.

Ensure all exit doors and exit hatch are functioning properly at all times.

Refer to SIDE DOOR AND ESCAPE HATCH EMERGENCY EXIT MAINTENANCE GUIDE in THIS SECTION.

This label is installed in the cab. In addition to the previous label it is a reminder to check the machine daily for the possibility of debris build-up, leaks, damaged wires and hoses and take the necessary action required to clean up any debris accumulation, repair any leaks, damaged wires or hoses.

EMERGENCY EXIT, HAND TIGHTEN ONLY

The label also advises to check and ensure that all fire fighting devices are in good working order.

This label is located on each of the escape hatch clamp-brackets to indicate that the escape hatch can also be used as an emergency exit.

The label also indicates that the escape hatch knobs should be hand tightened only to allow for easy exit.

Ensure all exit locations are functioning properly.

Refer to ESCAPE HATCH EMERGENCY EXIT in SECTION 2 of the OPERATOR'S MANUAL. Refer to SIDE DOOR AND ESCAPE HATCH EMERGENCY EXIT MAINTENANCE GUIDE in THIS SECTION.

1.28

Tigercat 726E Feller Buncher

Safety

EXTERIOR LABELS The following safety labels are installed on the exterior of this machine. These labels are located on the machine in the area where the specific safety concern is applicable. Labels must be periodically cleaned and inspected to ensure legibility is maintained. Replace any label that becomes illegible, damaged or removed.

KEEP BACK

This label warns personnel to KEEP BACK 150 m (500 ft) from the machine due to flying projectile hazard. Danger exists most prominently to the front and rear of the mulching head and around the felling head.

When approaching an operating machine on foot, stay at least 150 m (500 ft) away until the operator recognizes your presence. Make sure that all equipment has been shut down before advancing to the machine.

CRUSH HAZARD

This label warns of the crush zone in the center joint area. This can occur when the machine steering is used. DO NOT WORK IN THIS AREA UNTIL THE ARTICULATION LOCK BAR IS INSTALLED! Before working in the center joint area, INSTALL THE CHASSIS ARTICULATION LOCK BAR between the chassis and center joint to prevent accidental articulation which could result in death or serious injury.

Refer to ARTICULATION LOCK in SECTION 3 of THIS MANUAL for complete instructions.

1.29

Tigercat 726E Feller Buncher

Safety

ENTANGLEMENT HAZARD

CUTTING HAZARD

36779BUNI R0

This label warns of an ENTANGLEMENT HAZARD (rotating parts) zone.

This label informs you of the cutting hazards of the cooling fan blade when the engine is running.

The label is located near the front of the engine and the engine serpentine drive belt. DO NOT PLACE HANDS OR FINGERS IN THIS AREA. Rotating parts such as pulleys, belts and drives can cause entanglement of body parts resulting in serious injury.

KEEP CLEAR of cutting hazards caused by rotating components.

The label is located on the side of the engine cooling fan shroud. DO NOT PLACE HANDS OR FINGERS IN THIS AREA. Rotating parts such as cooling fan blades can cause entanglement of body parts resulting in serious injury.

KEEP HANDS AND FINGERS CLEAR OF ROTATING BELT, DRIVE OR PULLEY! Before performing any service work on these parts or in this area, shut engine off and wait for rotating parts to come to a complete stop.

KEEP HANDS AND FINGERS CLEAR OF ROTATING FAN BLADES! Before performing any service work on these parts or in this area, shut engine off and wait for rotating parts to come to a complete stop.

1.30

Tigercat 726E Feller Buncher

Safety

CRUSH HAZARD

EXPLOSIVE RELEASE OF HOT COOLING SYSTEM PRESSURIZED FLUID

33952AUNI R0

This label warns of the CRUSH HAZARD caused by the boom when it is not properly supported.

This label warns of a PRESSURE AND FLUID SPRAY HAZARD when the coolant in the radiator is hot.

Never work under or near an unsupported boom or attachment. Contact with a falling boom COULD RESULT IN DEATH OR SERIOUS INJURY!

DO NOT LOOSEN CAP UNTIL COOL. Explosive release of fluids from pressurized cooling system can cause serious burns.

Always lower the boom to the ground so that the weight of the boom and attachment is resting on the ground. Properly support and brace boom and shut off engine before performing service work.

Shut off engine. Only remove coolant filler cap when cool enough to touch with bare hands.

Slowly loosen cap to first stop to relieve pressure before removing completely.

1.31

Tigercat 726E Feller Buncher

Safety STORED ENERGY HAZARD

EXPLOSION HAZARD

WARNING

WARNING

• EXPLOSION HAZARD. • DO NOT USE ETHER. • ENGINE EQUIPPED WITH HEATER STARTING AID. • USE OF ETHER COULD RESULT IN DEATH OR SERIOUS INJURY. 36782BENG R0

This label warns of an EXPLOSION HAZARD. It is located on the end of the air cleaner (air filter housing). The engine is equipped with a heater starting aid, DO NOT USE ETHER to assist in starting the engine.

USING ETHER COULD CAUSE AN EXPLOSION WHICH COULD RESULT IN DEATH OR SERIOUS INJURY.

• STORED ENERGY HAZARD • THE ACCUMULATOR HAS 3000 PSI OF STORED ENERGY. SERVICING THE ACCUMLATOR BEFORE RELEASING PRESSURE COULD RESULT IN DEATH OR SERIOUS INJURY.

FLUID SPRAY HAZARD

• DO NOT SERVICE THE ACCUMULATOR BEFORE RELEASING PRESSURE BY APPLYING BRAKES 25 TIMES WITH ENGINE OFF. 39945BENG R0

This label warns of a STORED ENERGY HAZARD.

This label is located above the pressurized water system fill plug in the right rear corner of the machine.

The machine is equipped with an accumulator (located in the front chassis). The accumulator has stored energy in the form of hydraulic pressure. Servicing the accumulator or any hydraulic components before releasing pressure could result in death or serious injury.

The machine is equipped with a pressurized water system. A water tank is incorporated into the rear bumper and is pressurized to 4 bar (60 psi).

DO NOT SERVICE ACCUMULATOR OR ANY HYDRAULIC COMPONENTS BEFORE RELEASING PRESSURE.

Contact with fluid under pressure may cause injury.

Refer also to RELEASING PILOT PRESSURE FROM THE ACCUMULATOR in THIS SECTION.

This label warns of a FLUID SPRAY HAZARD.

DO NOT SERVICE PRESSURIZED WATER SYSTEM until air pressure is fully released by depressing the water system spray nozzle.

Tank fill plug has a cross drilled vent hole. Do not replace with standard plug.

Refer also to PRESSURIZED WATER SYSTEM MAINTENANCE in SECTION 3 of THIS MANUAL.

1.32

Tigercat 726E Feller Buncher

Safety

FIRE PREVENTION!

FIRE EXTINGUISHER ACCESS HOLE

This label indicates the location of each FIRE EXTINGUISHER ACCESS HOLE. The label is installed on each fire extinguisher hole on the engine hood.

This label advises operator's of the following: READ UNDERSTAND AND FOLLOW THE FIRE PREVENTION GUIDELINES IN THIS MANUAL. These guidelines provide all the necessary action required to preventing fires on this machine. DO NOT OPERATE THIS MACHINE until you have read these instructions and have performed any necessary maintenance required that will prevent the potential of a fire from starting on this machine.

It is also important to note that fire prevention inspections and maintenance MUST BE PERFORMED FREQUENTLY (several times per day). A clean combustible free machine as well as frequent inspections of the exhaust components, hydraulic hoses and electrical cables and performing any necessary repairs immediately will help prevent fires.

Maintain a CHARGED fire extinguisher on the machine at all times, know where it is and KNOW HOW TO USE IT!

1.33

Tigercat 726E Feller Buncher

Safety

1.34

DANGER

i

USING HIGH SPEED DISC SAWS SAFELY This information is intended to encourage logging organizations and operators to develop and practice additional rules that suit particular terrain conditions and job requirements. It is also intended to assist towards a quicker understanding of how and why things can happen when a high speed disc saw is in use; and hence to assist in development of safe operating practices.

The following information is in addition to any safety instructions or recommended safe operating practices that may already be in circulation.

CONTENTS COMMENTS AND INSTRUCTIONS DIRECTION OF THROW.......................................................... 7 HIGH ANGLE WRIST ROTATION ABILITY.............................. 8 RECOGNIZING THE DANGERS.............................................. 7 THROWING LONG WOOD PIECES...................................... 10 DANGERS.................................................................................... 3 FORWARD................................................................................... 2 BE AWARE OF THE HAZARDS............................................... 2 OTHER INSTRUCTIONS......................................................... 3 SEVERAL TYPES OF HEADS INVOLVED.............................. 2 STORED ENERGY................................................................... 2 HIGH ANGLE WRIST ROTATION CAPABILITY.......................... 9 SAW HEAD DON'TS.................................................................. 15 TYPE OF HOUSING MAKES A DIFFERENCE............................ 4

5211A • R2-1101

PAGE 1 OF 16

Using high speed disc saws safely FORWARD:

Tigercat

Several types of heads involved Tigercat wheel type feller-bunchers and crawler feller-bunchers can be supplied with several optional makes and models of high speed disc saw tree felling heads. Because each has certain advantages and disadvantages they are chosen where they best do specific types of work.

Stored energy The saw blade stores energy from the hydraulic motor during the times between tree cuts so that it can supply up to 1000 hp during a 1 sec tree cut. However this rotational energy, if misapplied can result in wood materials or other objects being thrown strongly enough to cause damage and to hurt people.

Be aware of the hazards It is important that users of machines with disc saw felling heads are aware of certain safety precautions that need to be taken. In this section some previously unknown, unexpected safety hazards are illustrated and explained . These should be studied before use of the machinery and then reviewed again after use has begun.

FIGURE 1: BROADSIDE SAW CONTACT WITH A LOG COULD PRODUCE A THROW

FIGURE 2: A SUDDEN MACHINE MOVEMENT MAY 2 THROW AT THE CAB CAUSE AN UNEXPECTED

Using high speed disc saws safely

Tigercat

Safe practices It is understood and expected that logging organizations and operators will develop and practice additional rules that suit (for example) particular conditions of terrain, trees, soil and job requirements. The information given here is intended to assist towards a quicker understanding of how and why things can happen when a high speed disc saw is in use; and hence to assist in development of safe operating practices.

It should not be assumed that all possible dangers have been discovered and described here.

Other instructions It is also understood and expected that all instructions contained in service and operator's manuals for use and maintenance of Tigercat disc saw heads and other disc saw heads installed on Tigercat machines will be followed.

THE DANGERS

There are at least these means by which a rotating disc saw can cause harm by throwing: • The normal throwing of chips from the cut.

• Soil particles are thrown from the ground.

• Loose chunks of wood encountered or produced are tossed by the exposed blade.

• Sticks and debris falling onto the blade or sliding across the blade are struck by the teeth and thrown.

• Metal pieces from the blade or from objects encountered are thrown.

• Wood pieces enter the saw housing and are expelled by the blade.

• In very peculiar cases the saw can throw long lengths of wood as spears.

3

Using high speed disc saws safely

Tigercat

TYPE OF HOUSING MAKES A DIFFERENCE Since the configuration of the saw housing can affect the safety of its use we need to identify some particular types of housing shapes and guarding being used.

Figure 3 shows a typical commonly used saw housing plan where there is a continuous skirt around the saw except at a mouth opening where the trees are cut and taken. The skirt extends below the saw enough to intercept tangential throw. There are snouts on both sides of the mouth so that if pushed against the side of a felled tree or log the saw teeth will not contact the wood.

THROW ANGLE

IF A SAW HEAD IS PUSHED AGAINST THE SIDE OF A FELLED TREE, SNOUTS PREVENT SAW TEETH FROM CONTACTING WOOD.

FIGURE 3: TYPICAL COMMONLY USED SAW HOUSING, CONTINUOUS SKIRT WITH OPENING WHERE TREES ARE CUT. SNOUTS ON BOTH SIDES OF THE MOUTH.

4

Using high speed disc saws safely

Tigercat

Figure 4 shows another commonly used plan. It has no blade guarding snouts so that the saw blade teeth do protrude ahead of the housing. This may be preferred over figures 3 and 5 for dexterity in tree getting.

THROW ANGLE

IF A SAW HEAD WITHOUT SNOUTS IS PUSHED AGAINST THE SIDE OF A FELLED TREE, SAW TEETH WILL CONTACT WOOD.

FIGURE 4: ANOTHER COMMONLY USED HOUSING PLAN WITH NO SNOUTS, BLADE TEETH PROTRUDE AHEAD OF THE HOUSING.

In figure 5 there is a much longer snout on the ingoing side of the mouth, i.e., where the teeth of the rotating blade are entering the housing. The broad side of a log, if nudged, will not contact the saw teeth and more thrown material will be intercepted by the extra length of snout.

THROW ANGLE

NUDGED LOG WILL NOT CONTACT SAW TEETH. EXTRA LENGTH OF SNOUT WILL INTERCEPT PORTION OF THROWN MATERIAL.

FIGURE 5: HOUSING USES LONGER SNOUT ON IN-GOING SIDE OF MOUTH WHERE ROTATING BLADE ENTERS HOUSING.

5

Using high speed disc saws safely Housing types cont.

Tigercat

In figure 6a and 6b there is an additional opening in the housing skirt. Openings in this location are sometimes provided for escape of wood chips produced by the saw teeth in the cut and being taken into the housing.

A CHIP ESCAPE PORT CAN ALLOW THROW BEHIND THE MACHINE

REAR

FRONT

FIGURE 6a

FIGURE 6b

FIGURE 6c

FIGURE 6: ADDITIONAL OPENING IN THE HOUSING SKIRT.

In figure 6c a guard has been added to the chip escape port so that tangential travel of chips and other material is intercepted as soon as it leaves the housing.

Each figure shows a shaded area where normally tangentially thrown material can escape from the saw housing. Deflected and dropped chips escaping below the bottom edge of the housing skirt are not included. The areas and angles are not exact but do show that one head can be different from another.

It is important that the operator familiarize himself with the blade rotation direction, the effectiveness of any snout on the in-going side and which direction any chip escape ports allow material to fly.

6

Using high speed disc saws safely COMMENTS AND INSTRUCTIONS

Tigercat

Recognizing the Dangers While it may appear that these illustrated danger areas can be visually recognized on the job by observing how far chips fly during a cut, that is only true for chips and other light weight materials.

Metal parts and wooden spears can be thrown to surprisingly greater distances. Even distant personnel on the ground, in other vehicles, or in buildings are at risk if the throw is in their direction.

Direction of throw The direction of possible tangential throw for metal parts and stones is dependent on the housing configuration and might be expected to be the same as observed for the chips. However, these throws can occur at any time the saw is running, in whichever direction the angle of throw is pointed by boom geometry, not just when a cut is being made.

Throw distance The throw distance for metal pieces and stones, can be many times the distance shown by the pattern for chips. More testing and data collection is needed to pin down a “safe distance” but if someone or something is in a place that can be seen by the operator and in the throw direction of a high speed disc saw, then the operation is not safe regardless of the distance.

Safe operating areas These saw heads must not be used in areas where the logging operation does not have control over the presence and movement of people. In particular, clearing of vegetation in urban and populated areas should not be done with a Tigercat manufactured or supplied high speed disc saw. High speed disc saw heads are intended for high productivity wood harvesting in areas remote from normal habitation. The possible presence of people and property within throw range and the likelihood of encountering scrap metal, wire fencing, steel posts and concrete must be respected.

Assessing the potential dangers on the job site The extent of danger from high speed disc saws on the logging operation has to be assessed on the job site, depending on how much other work activity is in the area and whether the operator can do his job of cutting and bunching with good control of throw patterns. Danger is greater if the saw is equipped with detachable, or fragile, or brittle teeth, or if the site contains stones or abandoned metal.

7

Using high speed disc saws safely Comments and Instructions cont.

Tigercat

Regular maintenance Poor saw maintenance increases these dangers. Some designs that might allow fasteners to wear thin or fatigue and suddenly break, need thorough timely replacement procedures. It is important that the warning signs of missing saw tooth parts or the sounds of striking rocks be heeded and the operation adjusted to avoid danger.

High angle wrist rotation ability When a felling machine is equipped with a high speed disc saw head with a high angle wrist rotation ability it should be determined that the limits of the boom, stick, tilt, wrist, upper leveling and any other freedoms, do not permit a direct throw at the operators cab during normal operation, see figure 7a. It is probably essential that the housing have a long snout on the throw side and that if a chip escape port is used it should be guarded.

With these high mechanical freedom arrangements there is a chance that an unforeseeable operator misadventure or equipment failure could result in an accidental direct or deflected throw at the operators cab, refer to figure 2 and 7b. The cab should be capable of resisting such accidental and ricochet throws. The velocity energy of metal or rock pieces leaving the blade is extremely high. The operators cab cannot be considered safe to routinely operate in the chip throw area, even if it has been especially constructed to prevent penetration by accidentally thrown objects.

8

Using high speed disc saws safely

Tigercat

FELLING HEAD • WITH A CHIP ESCAPE PORT AND SHORT SNOUT. • SHOWN IN A HIGH ANGLE WRIST ROTATION POSITION, PLACING OPERATOR'S CAB IN DIRECT LINE WITH UNGUARDED CHIP ESCAPE PORT

FIGURE 7a

PLAN VIEW OF MACHINE SHOWING CLOCKWISE AND COUNTERCLOCKWISE BLADE ROTATION

FIGURE 7b FELLING HEAD • WITH LONGER SNOUT ON THROW SIDE OF OPENING AND WITH A GUARDED CHIP ESCAPE PORT.

FIGURE 7: DISC SAW FELLING HEAD WITH HIGH ANGLE WRIST ROTATION CAPABILITY

9

Using high speed disc saws safely Comments and Instructions cont.

Tigercat

Throwing long wood pieces Dangers from throws of long wood pieces are illustrated in figures 8 to 11. Tests and experience have shown that when a high speed rotating saw is applied to a loose piece of wood, the wood is either blown or pushed away, without a throw. If the wood is held firmly in all directions and the saw advanced into it at any feed speed, cutting will take place. If the wood is only held against escape from the saw radially, but not held tangentially, then the wood will be both partly cut and partly moved tangentially. In this last case tests have shown that if the piece of wood is backed-up by a solid slippery surface; and if the feed in is very fast; and if the piece of wood is long enough; then the tangential movement is a dangerous spear-like throw.

A SLAB, WHICH COULD LATER BE THROWN, MIGHT HAPPEN WHEN NOT ENOUGH ROOM IN HEAD TO COMPLETELY CUT THE LAST TREE

SLAB

SLAB

N

I ED

FE

FIGURE 8a: HOW A SLAB CAN BE THROWN FROM THE SIDE OF A LOG

TH DIR ROW EC TIO N

SAW HOUSING HAS SKIS, BUT WITHOUT SNOUTS AND BLADE TEETH PROTRUDE AHEAD OF THE HOUSING.

FIGURE 8

THROW ENGAGEMENT DISTANCE FELLING HEAD MOVING INTO SLAB/LOG

SLAB

LOG A LONG THROW ENGAGEMENT DISTANCE CAN CAUSE A DANGEROUS SPEAR THROW

FIGURE 8b SIDE VIEW

FEED IN

IF THE SIDE OF A LOG CAN CONTACT THE SAW, THE THROW ENGAGEMENT DISTANCE CAN BE LONG

10

FIGURE 8c TOP VIEW

Using high speed disc saws safely Comments and Instructions cont.

Tigercat

Figures 8 and 9 show two ways that this might happen in the woods if using the saw head of figure 4 (where the throw contact can be long). A slab, still partly attached to a well backed-up tree bole and wet with sap, makes an ideally bad throw situation which could unintentionally occur in woods work. A small log in a pile of other logs might also be propelled out with enough length of continued contact to reach near saw tip speed.

A SMALL LOG IN A PILE OF OTHER LOGS MIGHT ALSO BE PROPELLED OUT WITH ENOUGH LENGTH OF CONTINUED CONTACT WITH THE BLADE TO REACH NEAR SAW TIP SPEED.

ED

FE

IN

FELLING HEAD MOVING INTO LOG PILE

FIGURE 9a: HOW A LOG CAN BE THROWN LIKE A SPEAR

SAW HOUSING WITHOUT SNOUTS AND BLADE TEETH PROTRUDE AHEAD OF THE HOUSING. THROW ENGAGEMENT DISTANCE

SMALL LOG LOG PILE FEED IN

A SAW HOUSING WITHOUT SNOUTS ALLOWS A LONG THROW ENGAGEMENT DISTANCE

FIGURE 9b SIDE VIEW

FIGURE 9c TOP VIEW

IF THE SIDE OF A LOG CAN CONTACT THE SAW, THE THROW ENGAGEMENT DISTANCE CAN BE LONG

FEED IN

11

Using high speed disc saws safely Comments and Instructions cont.

Tigercat

Figure 10 shows how a head with snouts does not allow a long throw contact. Although tests show that a short contact length on a long log or tree butt does not result in a spear like throw, this action should nevertheless be avoided because abnormally large chips are sometimes produced and thrown.

UNCUT TREE OR STUMP BACKUP

THROW ENGAGEMENT DISTANCE

WHEN ONLY THE END OF A LOG CAN MAKE CONTACT WITH THE SAW, THERE IS NOT MUCH THROW ENGAGEMENT DISTANCE

FIGURE 10: FELLING HEAD HOUSING WITH SNOUTS DOES NOT ALLOW A LONG THROW CONTACT

FELLING HEAD MOVING INTO LOG

Figure 11 warns that blocks of wood can be tossed in any direction when improvising with a disc saw to trim over-size stumps. A long snout and a slow feed speed lessen danger during stump trimming.

A similar danger of throw may exist when clearing small brush with multiple pass cuts.

FELLING HEAD MOVING INTO STUMP (FEED SPEED)

FIGURE 11: A BLOCK OF WOOD CAN BE TOSSED WHEN TRIMMING STUMPS

12

Using high speed disc saws safely Comments and Instructions cont.

Tigercat

Saw blade throw gap Saw blades have gaps between adjacent teeth and holders to permit installation and removal of the teeth and to provide spaces to accumulate chips in the cut, see figure 12. Fallen sticks and debris or sticks and debris sliding across the the saw blade can enter these gaps when the blade is rotating and be struck by the teeth and be tossed or thrown. Larger gaps and lower rotation speeds increase these dangers.

THROW GAP

FIGURE 12: SAW BLADE THROW GAP

13

Using high speed disc saws safely Comments and Instructions cont.

Tigercat

Saw housing entrance and exit space To avoid the ingestion of materials into the housing space above the disc (and later ejection) the ingoing entrance for the saw rim of teeth is kept as small as practical. It is important that this high wear area be maintained at its original size and shape. The outgoing opening is large enough to allow the housing to clean itself and will allow most things inside to be thrown out, see figure 13. Its throw direction and angle must be respected. A long snout on the other side reduces this danger.

THE INGOING ENTRANCE OF THE HOUSING FOR THE SAW RIM OF TEETH SHOULD BE SMALL

THE OUTGOING OPENING IS LARGER TO ALLOW THE HOUSING TO CLEAN ITSELF AND WILL ALLOW MOST THINGS INSIDE TO BE THROWN OUT

FIGURE 13: SAW BLADE ENTRANCE AND EXIT SPACE

14

Using high speed disc saws safely Comments and Instructions cont.

Tigercat

This information is offered by Tigercat as part of interim action to make saw heads safer. It is based on what has recently been reported from the field and on tests conducted on proving grounds. Tigercat is continuing to do design and testing of tree felling machinery towards achieving greater safety in the woods. Tigercat would be thankful for written reports describing any unsafe happenings, including near misses, in the use of felling heads and their carriers.

The following are some “SAW HEAD DON’TS” that apply particularly to throw prevention.

Do not point the throw of a disc saw head in a direction towards people, vehicles or buildings at any visible distance.

Do not operate in a way that throws chips in a direct-line at the machine cab.

Do not push hard with the saw against anything except a standing tree to be cut.

Do not mix new sharp teeth with old dull teeth on the same saw.

Do not change the blade rotation from its designed direction in the head.

Do not over speed the blade rpm.

Do not remove or shorten snouts provided by the head manufacturer or installer.

Do not neglect tooth fastening inspection, maintenance and replacement.

Do not neglect to repair worn or damaged saw housings.

Do not neglect to replace any covers removed for service or clean out.

Do not count on skis to give the throw protection that snouts do.

Do not nudge loose short pieces with the front of any type of head.

Do not nudge anything, even long logs, with the front of a head which has no snouts.

Do not cut short small stalks when blade speed is low.

Do not operate a high speed disc saw in a populated area.

Do not assume that visitors and other workers are aware of disc saw dangers.

Do not assume that the operator will spare you, a visitor, from danger.

Do not select and operate heads that throw rearward.

Do not select and operate heads with unnecessarily wide throw angles.

Do not neglect to read and follow all instructions provided by the saw and head manufacturers.

15

Using high speed disc saws safely

16

Tigercat

Tigercat 726E Feller Buncher SECTION 2 - CONTROLS AND OPERATION JANUARY, 2014

CONTENTS - SECTION 2 A

ACCESS PANELS, ENGINE.............................................................................................................................2.55 ACCUMULATING ARMS.....................................................................................................................................2.8 AIR CLEANER, ENGINE...................................................................................................................................2.62 AIR CLEANER UNLOADER VALVE.................................................................................................................2.64 AIR CONDITIONER/HEATER...........................................................................................................................2.15 AIR FILTER ELEMENTS...................................................................................................................................2.62 AIR INTAKE SYSTEM, ENGINE FILTER RESTRICTION INDICATOR.............................................................................................................2.62 AIR VENTS.......................................................................................................................................................2.16 ALARM LIGHT................................................................................................................................................... 2.11 ARTICULATION LOCK BAR.............................................................................................................................2.80 AUXILIARY POWER SUPPLY, 12 VOLT...........................................................................................................2.14 B

BATTERY DISCONNECT SWITCH..................................................................................................................2.18 BOOM CYLINDER LOCK.................................................................................................................................2.81 BOOM LIFT.........................................................................................................................................................2.8 BOOM LIFT LOCK............................................................................................................................................2.81 BRAKES..............................................................................................................................................................2.9 C

CAB CONTROLS CONTROL PANEL

PARKING BRAKE SWITCH.............................................................................................................. 2.13

CENTER JOINT LOCK PIN...............................................................................................................................2.80 CIGAR LIGHTER...............................................................................................................................................2.14 CLAMP ARMS.....................................................................................................................................................2.9 CLEANING A/C CONDENSER, AND COOLER PACKAGE..............................................................................2.65 CLEANING INSTRUCTIONS FOR GLASS WINDOWS...................................................................................2.77 COLD WEATHER STARTING...........................................................................................................................2.72 COMPUTER.........................................................................................................................2.11, 2.26, 2.27, 2.28 ADJUSTMENT MENU...................................................................................................................................2.30 ALERT MESSAGES......................................................................................................................................2.50 CRITICAL MESSAGES.................................................................................................................................2.41 DATE/TIME ADJUSTMENT...........................................................................................................................2.37 DISPLAY ADJUSTMENT...............................................................................................................................2.36 ENGINE MENU.............................................................................................................................................2.29 GENERAL SETTINGS...................................................................................................................................2.31 INFORMATION MENU..................................................................................................................................2.34 MAIN MENU PAGE.......................................................................................................................................2.35 MESSAGES...................................................................................................................................................2.40 MESSAGES - ALERT

DENOX FAULT CODE...................................................................................................................... 2.54 DIESEL EXHAUST FLUID < 5%....................................................................................................... 2.53 DIESEL EXHAUST FLUID LEVEL <10%.......................................................................................... 2.53 DIESEL EXHAUST FLUID LEVEL EMPTY....................................................................................... 2.53 DRIVE CHARGE FILTER BYPASS................................................................................................... 2.52 ENGINE FAULT CODE..................................................................................................................... 2.54 FUEL - WATER IN FUEL................................................................................................................... 2.53 HARDWARE FAULT - MD3............................................................................................................... 2.52 HARDWARE FAULT - XA2................................................................................................................ 2.52

MESSAGES - CRITICAL

AFTER TREATMENT SYSTEM ENGINE IDLE TOO LONG............................................................ 2.48 AFTER TREATMENT SYSTEM TECHNICAL FAILURE................................................................... 2.47 DENOX FAULT CODE...................................................................................................................... 2.47 DIESEL EXHAUST FLUID QUALITY................................................................................................ 2.46 ENGINE FAULT CODE........................................................................................................... 2.44, 2.45 ENGINE LOCKED OUT.................................................................................................................... 2.48

Tigercat 726E Feller Buncher

Controls and Operation

ENGINE OIL PRESSURE LOW........................................................................................................ 2.45 ENGINE OIL TEMPERATURE HIGH................................................................................................ 2.45 ENGINE RESTARTS REMAINING UNTIL ENGINE LOCKOUT....................................................... 2.49 ENGINE STOP.................................................................................................................................. 2.43 ENGINE TORQUE DERATE ACTIVE............................................................................................... 2.48 HARDWARE FAULT - DENOX MODULE......................................................................................... 2.44 HARDWARE FAULT - ENGINE......................................................................................................... 2.43 HARDWARE FAULT - MD3............................................................................................................... 2.43 HARDWARE FAULT - XA2................................................................................................................ 2.43 HYDRAULIC OIL LEVEL LOW.......................................................................................................... 2.42 HYDRAULIC OIL RETURN FILTERS BYPASSED........................................................................... 2.49 HYDRAULIC OIL TEMPERATURE HIGH......................................................................................... 2.42

PREFERENCES MENU................................................................................................................................2.35 SCREEN SAVER ADJUSTMENT..................................................................................................................2.36 CONTROLS - CAB..............................................................................................................................................2.8 COOLER PACKAGE.........................................................................................................................................2.65 D

DEF (DIESEL EXHAUST FLUID, TANK............................................................................................................2.59 DENOX FAULT CODE MESSAGES - ALERT...................................................................................................2.54 DENOX FAULT CODE MESSAGES - CRITICAL..............................................................................................2.47 DIAGNOSTICS CONNECTION, ENGINE.........................................................................................................2.18 DIESEL EXHAUST FLUID (DEF) LEVEL WARNINGS.....................................................................................2.53 DIESEL EXHAUST FLUID (DEF) TANK............................................................................................................2.59 DOME LIGHT....................................................................................................................................................2.15 DRIVE CONTROL...............................................................................................................................................2.9 E

EMERGENCY EXIT/SKYLIGHT........................................................................................................................2.15 ENGINE RPM............................................................................................................................................................... 2.11 STARTING IN COLD WEATHER...................................................................................................................2.72 ENGINE ACCESS PANELS..............................................................................................................................2.55 ENGINE AIR PRECLEANER............................................................................................................................2.63 ENGINE DIAGNOSTICS CONNECTION..........................................................................................................2.18 ENGINE FAULT CODE MESSAGES - ALERT..................................................................................................2.54 ENGINE FAULT CODE MESSAGES - CRITICAL................................................................................... 2.45, 2.47 ENGINE, HOT WATER SHUT OFF VALVE.......................................................................................................2.17 ENGINE RESTARTING AFTER RUNNING OUT OF FUEL..............................................................................2.71 ENGINE, STARTING.........................................................................................................................................2.70 ENGINE, STARTING IN COLD WEATHER.......................................................................................................2.72 ENGINE, STOPPING........................................................................................................................................2.74 F

FAN SWITCH, ENGINE COOLING...................................................................................................................2.13 FILTER - CAB FRESH AIR................................................................................................................................2.16 FILTER, RECIRCULATING AIR - A/C UNIT......................................................................................................2.16 FIRE EXTINGUISHER......................................................................................................................................2.17 FOOT CONTROL, CENTER...............................................................................................................................2.9 FOOT CONTROL, LEFT.....................................................................................................................................2.9 FOOT CONTROL, RIGHT...................................................................................................................................2.9 FUEL REFUELING..................................................................................................................................................2.58 FUEL TANK.......................................................................................................................................................2.58 FUSE AND RELAY PANEL CAB...............................................................................................................................................................2.19 MAIN..............................................................................................................................................................2.20 FUSE PANEL....................................................................................................................................................2.18 H

HEAD TILT..........................................................................................................................................................2.8 HORN..................................................................................................................................................................2.8 HOT WATER SHUT OFF VALVE (ENGINE).....................................................................................................2.17 HYDRAULIC OIL FILL PUMP............................................................................................................................2.61 HYDRAULIC OIL TANK.....................................................................................................................................2.60

2.2

Tigercat 726E Feller Buncher I

Controls and Operation

ICONS, PICTOGRAM DESCRIPTIONS..................................................................................................... 2.4, 2.5 IGNITION KEY SWITCH...................................................................................................................................2.14 INSTRUMENT PANEL.......................................................................................................................................2.10 INTERLOCK RESET......................................................................................................................................... 2.11 J

JOYSTICK, LEFT................................................................................................................................................2.8 JOYSTICK, RIGHT..............................................................................................................................................2.8 K

KEY SWITCH, IGNITION..................................................................................................................................2.14 L

LIGHT - DOME..................................................................................................................................................2.15 LIGHTER, 24 VOLT...........................................................................................................................................2.14 LIGHTS WORK............................................................................................................................................................2.13 LIGHT SWITCH, WORK....................................................................................................................................2.13 M

MACHINE PREPARATION................................................................................................................................2.73 SYSTEM TEST AND WARM-UP...................................................................................................................2.73 MD3 COMPUTER................................................................................................................................... 2.26, 2.27 MD3 COMPUTER MAIN MENU........................................................................................................................2.28 O

OPERATING MACHINE.......................................................................................................................... 2.67, 2.73 P

PARKING BRAKE SWITCH..............................................................................................................................2.13 PICTOGRAM DESCRIPTIONS................................................................................................................... 2.4, 2.5 PRECLEANER, ENGINE AIR...........................................................................................................................2.63 PRESSURIZED WATER SYSTEM....................................................................................................................2.14 PRE-START CHECKS......................................................................................................................................2.67 R

RADIO, AM/FM STEREO / CD PLAYER...........................................................................................................2.14 REFUELING......................................................................................................................................................2.58 RESTARTING AN ENGINE AFTER RUNNING OUT OF FUEL........................................................................2.71 S

SCREEN SAVER ADJUSTMENT......................................................................................................................2.36 SEAT.................................................................................................................................................................2.24 SKYLIGHT/EMERGENCY EXIT........................................................................................................................2.15 SPEED CONTROL LEVER...............................................................................................................................2.10 STARTING ENGINE..........................................................................................................................................2.70 STEERING..........................................................................................................................................................2.8 STEREO RADIO/CD PLAYER..........................................................................................................................2.14 STOPPING ENGINE.........................................................................................................................................2.74 T

THROTTLE SPEED.......................................................................................................................................... 2.11 TOWING INSTRUCTIONS................................................................................................................................2.77 TRANSPORTING INSTRUCTIONS..................................................................................................................2.79 U

USB PORT, MD3 COMPUTER.........................................................................................................................2.18 W

WATER SYSTEM, PRESSURIZED..................................................................................................................2.14 WINDOWS........................................................................................................................................................2.75 CARE OF POLYCARBONATE WINDOWS...................................................................................................2.75

CAUTIONS........................................................................................................................................2.76 CLEANING INSTRUCTIONS............................................................................................................ 2.76 CONCEALING HAIRLINE SCRATCHES.......................................................................................... 2.76 FIRE PRECAUTIONS....................................................................................................................... 2.76 GRAFFITI REMOVAL........................................................................................................................ 2.76 INSPECTION AND MAINTENANCE................................................................................................. 2.75 RESISTANCE TO CHEMICALS........................................................................................................ 2.75 RESISTANCE TO WATER................................................................................................................ 2.75

CLEANING INSTRUCTIONS FOR GLASS WINDOWS................................................................................2.77 WORK LIGHTS SWITCH..................................................................................................................................2.13

2.3

Tigercat 726E Feller Buncher

Controls and Operation

PICTOGRAM DESCRIPTIONS Diagrams in pictorial form are used to represent machine function operation. Some of the symbols are signs, characters, figures, or any components related to the operation of the machine. They are a simple universal language of symbols or pictograms that illustrate a function or component without the use of words. Pictograms are installed on or in close proximity to the switch or device used to activate or deactivate the machine function or they may be a sign used on a warning or indicator light of a function that is operating or advising of an alarm condition.

Examples of these pictograms are the turtle speed such as SLOW =

or FAST =

and the rabbit

that are often used to describe

.

The pictograms used on this machine are as follows: = Adjustment Menu Icon

= Control Lever Multiple Direction

= Air Conditioner ON

= Control Lever One Direction = Control Lever Two Direction

= Air Conditioner OFF

= Accumulator arms OPEN

= Air Source, Fresh Air

= Accumulator arms CLOSE

= Air Source, Recirculate

= Alert Message Symbol

= Clamp arms CLOSE

= Auxiliary Power Outlet 12 V

= Clamp arms OPEN

= Power Outlet 24 V

= Critical Message Symbol

= Battery Disconnect

= Cruise Control

= Boom DOWN

= Differential Locks (ON/OFF)

= Boom UP = Disc Saw = Boom Tilt Back

= Disc Saw ON

= Boom Tilt Forward

= Disc Saw Pressure

= Brake Pedal 2.4

Tigercat 726E Feller Buncher

Controls and Operation

PICTOGRAM DESCRIPTIONS CONTINUED = Diesel Exhaust Fluid

= Hydraulic Oil Level High

= Engine Emission System Failure = Hydraulic Oil Level Low

= Engine Start

= Engine STOP

= Imperial/Metric Toggle Symbol

= Engine SPEED

= Information Menu Icon

= Engine WAIT TO START

= Information Message Symbol

= Engine WARNING = Instrument Bulb Test = Engine Menu Icon = Interlock Reset ON = Error Message Symbol = Interlock Reset OFF

= Fan Auto Reversing/Cleaning

D

= Fan Full ON

= Lights, Work

= Fuel - Diesel

= Lights, Engine Service

= Fuel Level Low = Feller Buncher

= Horn = Hydraulic Oil Temperature

= Speed FAST or Hi = Speed SLOW or LOW

= Hydraulic Oil Temperature High

= Steer Right = Hydraulic Oil Level Low = Steer Left

= Hydraulic Oil Level 2.5

Tigercat 726E Feller Buncher

Controls and Operation

= Switch ON

= Switch OFF

= Temperature

= Ventilation Blower Fan = Windshield Washer

= Winch ON

= Winch Free Spool

= Winch Spool IN

= Winch Spool Out

2.6

Tigercat 726E Feller Buncher

1

2

Controls and Operation

3

4

9

15 10 6

7

8

9 14

5

11

12

13

1.

2.

3.

4.

5.

6.

7.

8.

FIRE EXTINGUISHER LEFT FOOT PEDALS BRAKE PEDAL RIGHT FOOT PEDALS LEFT DOOR SAFETY SWITCH LEFT JOYSTICK SEAT RIGHT JOYSTICK

M726E-111

9.

10.

11.

12.

13.

14.

15.

FUSE AND RELAY PANEL RIGHT DOOR SAFETY SWITCH INSTRUMENT PANEL HEATER/AC CONTROLS PILOT MANIFOLD (UNDER CAB) MD3 COMPUTER WARNING LIGHT

CAB COMPONENTS AND CONTROLS 2.7

Tigercat 726E Feller Buncher

Controls and Operation

IMPORTANT! This manual is applicable to factory installed machine functions and controls. It does not take into account any changes or modifications made after shipment. Verify all functions before operating this machine.

CONTROLS - CAB B

A B C

M726E-034

A

C

1

2

LEFT JOYSTICK

M726E-005

2.

BOOM JOYSTICK - RIGHT Boom Lift Move the joystick BACK to RAISE the boom.

Move the joystick FORWARD to LOWER the boom.

Attachment tilt Move the joystick to the RIGHT to tilt the attachment OUT. Move the joystick to the LEFT to tilt the attachment IN. Joystick Switches A. Accumulating Arms Open Push the switch to OPEN the accumulator arms.

B. Accumulating Arms Close Push the switch to CLOSE the accumulator arms.

C. Accumulating/Clamp/Shear Arms Open Push the switch to OPEN the accumulator and clamp/shear arms.

1. STEERING JOYSTICK - LEFT Steering Move the joystick to the RIGHT to turn the machine to the RIGHT. Move the joystick to the LEFT to turn the machine to the LEFT. Steering "speed" can be controlled by the amount the joystick is moved to the right or left. A small movement of the joystick will turn the machine slowly and a large movement of the joystick will cause the machine to turn very rapidly.

Joystick Switches A. Horn - Push to sound warning horn B. Differential Lock, Front

Push and hold to LOCK the FRONT differential and provide driving torque to BOTH front wheels.

C. Differential Lock, Rear

RIGHT JOYSTICK

Push and hold to LOCK the REAR differential and provide driving torque to BOTH rear wheels.

D. & E. Not Used

IMPORTANT! Use differential locks ONLY when additional traction is required. Do not continuously drive the machine with the differential locks on as this will result in damage to the axles.

2.8

Tigercat 726E Feller Buncher 5 5A 5B

213-20

4

Controls and Operation NOTE: As a safety precaution before working on or around the machine. Stop the engine and release pilot system pressure by performing the following steps:

3

1. Close both doors. Turn key switch to RUN position. Do not start the engine. Press interlock reset switch.

Complete either steps 2A or 2B. 2A. Repeatedly apply brake foot pedal 50 times or more.

2B. Engage front and rear differential lock switches and HOLD ON for 30 seconds.

While waiting, repeatedly apply brake foot pedal at least 10 times.

3. Pressure may remain in the system after completing all of the above steps.

Use caution when loosening hydraulic connections.

For additional information, refer to RELEASE PILOT SYSTEM PRESSURE in SECTION 5 of the SERVICE MANUAL.

FOOT PEDALS

RIGHT FOOT CONTROL - DRIVE CONTROL 3. RIGHT FOOT CONTROL - DRIVE CONTROL

LEFT FOOT CONTROL

Press the RIGHT foot pedal to drive FORWARD.

5. LEFT FOOT CONTROL - CLAMP ARMS Press the LEFT foot pedal to OPEN the clamp arms.

Press the LEFT foot pedal to drive in REVERSE.

Press the RIGHT foot pedal to CLOSE the clamp arms.

NOTE: A backup horn will sound when travelling in reverse.

CENTER FOOT CONTROL - BRAKES 4. CENTER FOOT CONTROL - BRAKES Depress the foot pedal to apply the hydraulic brakes.

2.9

Tigercat 726E Feller Buncher

Controls and Operation INSTRUMENT PANEL 1 2

6

3

7

4 M726E-045

5

6. SPEED CONTROL LEVER

9

8

The speed control lever allows the operator to set the maximum speed of the machine to maintain a given speed without having to feather the drive pedals. The speed control lever is mounted on the left hand arm rest, below and to the left of the steering joystick.

11

10

12

Push the lever forward to increase the maximum speed.

Pull the lever back to decrease the maximum speed of the machine. When the lever is pulled fully back the machine will be in CREEP MODE. Creep mode provides maximum available tractive force to the wheels at a reduced speed.

480-258

INSTRUMENT PANEL CONTROLS AND SWITCHES

The instrument panel is located on the right side of the cab beside the operator's seat right armrest. The following controls and switches are mounted on the instrument panel:

This lever can be used while the machine is in motion.

1. MD3 COMPUTER MODULE

Refer also to SPEED CONTROL LEVER ADJUSTMENT in SECTION 3 of THIS MANUAL.

3. INTERLOCK RESET SWITCH

2. ALARM LIGHT 4. THROTTLE SWITCH 5. CUTTER SWITCH (SAW) 6. FAN SWITCH (Engine Cooling) 7. WORK LIGHTS SWITCH 8. PARK BRAKE SWITCH 9. BLANKS 10. IGNITION KEY SWITCH 11. 12 VOLT AUXILIARY POWER SUPPLY 12. 24 VOLT LIGHTER

2.10

Tigercat 726E Feller Buncher

Controls and Operation

1. MD3 COMPUTER MODULE The MD3 computer, electronic control and display is the operator interface with the electronic control system. The MD3 is the central unit in the control system which works as both a master controller and a display unit. See MD3 COMPUTER ELECTRONIC CONTROL & DISPLAY later in this section for complete details and operation instructions.

3A

ACTUATOR

INTERLOCK SYSTEM SHUT OFF 3A. INTERLOCK SYSTEM SHUT OFF Both doors are equipped with interlock switches to prevent the machine from being operated while the doors are open (interlock system shut off).

2. ALARM LIGHT

M726E-046

This light flashes to alert the operator that an alarm condition has been detected and should be dealt with immediately. All warning messages can be viewed on the computer display on the instrument panel.

To operate: Close both doors then press and release the interlock reset switch.

Refer to the COMPUTER, MESSAGES in THIS SECTION. 3. INTERLOCK RESET SWITCH This is a two position switch and is used to reactivate the interlock system after it has been deactivated by opening either of the cab doors, or by turning the ignition switch to the OFF position. This system prevents accidental or improper use of the controls from anywhere but the operator's seat.

CAUTION: All functions on the machine can now be operated, either as intended or by accidentally touching them.

Once the safety interlock system has been activated, the safety of both the operator and all persons outside the cab becomes the responsibility of the operator.

These door interlock switches and the interlock reset switch are safety features and their function must not be defeated in any way.

With the engine running and both doors closed, press and then release this switch to REACTIVATE the interlock system.

4. THROTTLE SPEED SWITCH This is a momentary switch used to increase/ decrease engine speed. Press on bottom of switch to decrease engine speed. Press on top of switch to increase engine speed.

Maintaining Correct Engine RPM. It is most important that the RPM of the engine be correct at all times: Low Idle 850 +/- 25 RPM (No Load) High Idle 1850 +/- 25 RPM (No Load) NOTE: The above values are with the hydraulic and engine oil at normal operating temperatures and no functions activated.

2.11

Tigercat 726E Feller Buncher

Controls and Operation NOTE: When starting the saw and the hydraulic oil is not up to operating temperature, the saw can be turned on at 1500 rpm and as the saw begins to turn the engine speed can be reduced to idle to allow the oil to warm up.

NOTE: If the engine is turned off or the interlock system has been deactivated with the switch in the ON position, the saw will not start up when the engine is restarted. The switch must be turned OFF and then back ON for the saw to start.

Always decrease the engine speed to idle for several minutes to allow the saw to slow down before turning the saw off.

1 2

6

3

7

4 5

9

8

11

10

SAW PRESSURE INDICATOR

12

Each increment on the gauge represents approximately 1000 psi. During cutting operations the indicator value will rise as the blade slows down due to cutting, and fall as the blade speeds up. A 2/3 value or higher indicates that the blade has not attained full speed from the previous cut or has jammed.

Further cutting should be delayed until the indicator value falls below the 1/3 increment to prevent stalling the saw blade during the next cut. Below 1/3 the saw blade is at optimum cutting speed.

INSTRUMENT PANEL CONTROLS AND SWITCHES 5. CUTTER SWITCH - (SAW) 480-258

Use this switch to turn the saw ON or OFF. This switch sends a signal to the controller, the controller then sends a signal to the saw pump and valve to turn it on. The saw icon on the computer display will turn green when the saw is ON.

M726E-097

Place throttle in HIGH IDLE (min 1500 rpm) before turning saw ON.

2.12

Tigercat 726E Feller Buncher

Controls and Operation

6. FAN SWITCH (Engine Cooling) This is a three position momentary switch, FULL ON/AUTO/ CLEAN*. This switch along with the MD3 Computer, controls the operation of the variable pitch fan.

7. WORK LIGHTS SWITCH This is a two position switch. Use to turn ON the work lights.

8. PARKING BRAKE SWITCH P This is a two position switch which operates a driveline brake.

FULL ON

Press the top of this switch (ON) to ENGAGE the parking brake. The parking brake icon on the main menu of the computer display will be illuminated when the parking brake is engaged.

AUTO CLEAN

Press the bottom of this switch (OFF) to DISENGAGE the parking brake.

M726E-131

AUTO POSITION - AUTO is the normal operating position for the fan control switch.

When the switch is in the AUTO position, the fan will operate completely in an automatic mode.

NOTE: The parking brake must be ENGAGED to START the engine, and DISENGAGED to DRIVE the machine.

NOTE ALSO: The interlock system prevents the machine from being driven and function controls from being operated while the parking brake is ENGAGED.

NOTE: The MD3 Computer is programmed to reverse fan direction automatically when the fan switch is in the AUTO position. The default setting is reverse every ten minutes for ten seconds, This setting is adjustable See COOLING FAN PURGE INTERVAL and COOLING FAN PURGE LENGTH in this section for adjustment information.

3A

FULL ON POSITION - When the switch is in the FULL ON (OVERRIDE) position, the fan control system is overridden and the fan will operate at full speed forward. The FULL ON (OVERRIDE) position is intended for use in the event of a temporary failure of the fan control system. AUTOMATIC REVERSING/ CLEANING does not function in FULL ON position.

ACTUATOR M726E-046

INTERLOCK SYSTEM SHUT OFF

As part of the interlock system this machine automatically engages the parking brake whenever a cab door is open. This prevents accidental or improper operation of the controls from anywhere but the operator's seat.

CLEAN POSITION - When the switch is pressed momentarily to the CLEAN position, the fan direction is reversed. Reverse direction is used to help clean the charge air cooler, radiator, oil cooler, A/C condenser and air intake door screen. By "reversing" the fan blade direction, air flow is propelled in the opposite direction, thereby helping to force dust and debris off of the heat exchanger cores and screens.

Refer also to COMPUTER ~ MESSAGES AND WARNINGS - CRITICAL ~ INTERLOCK SYSTEM in THIS SECTION.

It is also important to manually clean debris from the machine on a regular basis to maintain low machine operating temperatures.

Refer to CLEANING A/C CONDENSER, CHARGE AIR COOLER, OIL COOLER AND RADIATOR in THIS SECTION.

2.13

Tigercat 726E Feller Buncher

Controls and Operation HOSE

1

WATER SHUT OFF VALVE (SHOWN CLOSED)

13

2

PRESSURIZED WATER SYSTEM CONTROL VALVE (UNDER SEAT) 13. VALVE - Pressurized Water System

6

3

196-16A

7

4 5

Turn the hand operated ball valve (shut off valve) under the seat to the ON position to draw water from the 40 Liters (10.5 gallon) pressurized holding tank at the rear of the machine. When not in use turn the water supply OFF at this valve and relieve the pressure in the rubber hose, under the operator's seat.

9

8

11

10

12

AIR CHARGE VALVE

INSTRUMENT PANEL CONTROLS AND SWITCHES 9. OPTIONAL SWITCH LOCATIONS 480-258

10. IGNITION KEY SWITCH This is a three-position switch labelled OFF/ RUN/START.

PRESSURE GAUGE

OFF Position - All electrical power fed through the ignition switch is turned “OFF”

196-9A

RUN Position - Connects the battery to electrical functions used for machine operation.

PRESSURIZED WATER SYSTEM

The pressure gauge on the side of the seat should read 4 Bar (60 psi).

Refer to PRESSURIZED WATER SYSTEM MAINTENANCE in SECTION 3 of THIS MANUAL

START Position - Used to energize the starter motor to start the engine.

11. 12 VOLT AUXILIARY POWER SUPPLY A 12 volt outlet with 20 amp capacity for portable devices such as cell phones.

12. 24 VOLT LIGHTER Cigar/cigarette lighter.

14

14. AM/FM STEREO RADIO/CD PLAYER With two front mounted speakers.

Refer to component manufacturer's manual supplied with the machine for adjustment procedures.

2.14

Tigercat 726E Feller Buncher

Controls and Operation B

15

A

C

D

A E

726E-070

15. SKYLIGHT/EMERGENCY EXIT

M726E-050

18. AIR CONDITIONER/HEATER

Provides tree top visibility and serves as a third cab exit should the two doors become blocked. There are two retaining handles (A) on the inside and two on the outside to allow removal of the hatch from either side. These handles should only be HAND TIGHTENED, to allow them to be unscrewed in case of an emergency.

16

The controls on this panel are used to adjust the heating and air conditioning temperature for operator comfort in the operator's cab.

A. A/C ON/OFF SWITCH This is a push/on push/off power switch.

B. FAN SPEED - OFF/LOW/MED/HIGH This is a rotary, four position switch for the fan speed.

C. AIR SOURCE - 2 POSITION This is a rotary, two position switch to select either, outside fresh air or to recirculate inside air. To maximize use of A/C place the control in the recirculate mode.

17

D. HEAT - VARIABLE This is a variable, rotary dial to adjust the amount of heated air for the cab. Make sure this control is off, when using the air conditioning.

16. LIGHT - DOME The switch is located on the side of the dome light fixture.

E. AIR CONDITIONING - VARIABLE This is a variable, rotary dial to adjust the temperature of cooled air for the cab.

17. RADIO - CB (IF EQUIPPED) Consult the manufacturer's instruction manual for additional information.

NOTE: To maximize the efficiency of the air conditioning, the heat control dial on the control panel must be rotated to the "OFF" position. Also refer to HOT WATER SHUT OF VALVE, in THIS SECTION. IMPORTANT! It is recommended that during cold weather when the A/C system is not in use, that it be run for a period of 5 minutes every 2 weeks. This will circulate oil to all components of the A/C system.

2.15

Tigercat 726E Feller Buncher

Controls and Operation 21

19

726E-037

FRESH AIR FILTER

21. FILTER - CAB FRESH AIR When the AIR SOURCE control knob (C) on the A/C Heater control panel is in the FRESH AIR position, outside air is drawn into the cab A/C Heater unit through this filter and mixed with interior air from the cab. The filter is located in the rear of the cab roof and accessible from outside the cab. It should be checked every 125 hours. This is done by removing 6 bolts and removing the air inlet cover. Next remove 2 bolts and remove the filter retainer. This will allow access to the filter.

20 M726E-001

AC/HEATER VENTS AND FILTER 19. AIR VENTS The Air Conditioner/Heater package has six air outlets in the cab.

20. FILTER, RECIRCULATING AIR - A/C UNIT When the AIR SOURCE switch is in the RECIRC AIR position, air in the cab is drawn into the A/C- HEATER unit via this filter and recirculated. The filter is located at the base of the A/C unit, below the right arm rest of the operator’s seat. It should be cleaned or replaced every 125 hours. Remove the two thumb screws in the filter box cover to access the filter.

The RECIRCULATING AIR FILTER and the CAB FRESH AIR FILTER may require cleaning more frequently under extreme operating conditions.

2.16

Tigercat 726E Feller Buncher

Controls and Operation

22

GAUGE

23 ENGINE

HOSE TO A/C HEATER UNIT

726E-003

HOT WATER SHUT OFF VALVE

22. HOT WATER SHUT OFF VALVE (ENGINE) To maximize the efficiency of the air conditioning, the HEAT control knob (D) on the A/C Heater control panel must be rotated to the "OFF" position. During times when cab heating is not required the HOT WATER SHUT OFF VALVE, on the heater hose from the engine, should also be closed to prevent hot water from seeping through the A/C unit, thereby reducing the effect of the cooling system.

23. FIRE EXTINGUISHER A portable fire extinguisher is located in operator's cab. The extinguisher should be checked daily to ensure that it is charged.

The pointer on the charge gauge should point to the green region. If the indicator falls out of this green area, the extinguisher should be serviced immediately.

Maintain a CHARGED fire extinguisher on the machine at all times and KNOW HOW TO USE IT. Refer to the manufacture's Use and Information manual for proper usage, additional information and recommended inspection and maintenance intervals.

24

726E-071

FRONT OF CAB INTERIOR

24. REAR VIEW MIRROR A (4" x 8") convex rear view mirror is located in the front of the roof to assist in the view out the rear windows. Use the mirror along with the camera monitor when driving the machine in reverse.

2.17

Tigercat 726E Feller Buncher

Controls and Operation

25

28

26

27

M726E-053 M726E-106

CAB FUSE ACCESS

26. FUSE PANEL - CAB

25. BATTERY DISCONNECT - SWITCH This manually operated switch located in the top of the battery compartment in the right rear corner of the machine, completely disconnects most electrical circuits on the machine from the battery.

The fuses, diodes, resistors and relays are located behind a panel below the instrument panel. Press the latch button to open the door to access the fuses, diodes, resistors and relays. See FUSE AND RELAY PANEL - CAB in THIS SECTION for more detail.

Turn the battery disconnect switch off if the vehicle is to be parked for an extended period of time (Example - overnight).

27. USB PORT - MD3 COMPUTER This USB port is used to access the MD3 computer. A laptop with appropriate IQAN software can be plugged into this port for software updates, diagnostics and some adjustments.

Note: This machine is equipped with an After Run/ Accessory Relay which delays by 90 seconds the power disconnect to engine related fuses and relays (ECU /ATS relay, NOx Sensor relay, NOx Sensor fuse, ECU Power fuse, DCU fuse). Whenever the engine is stopped all DEF solution is pumped back to tank before the engine power system is turned off. This process takes approximately 90 seconds. Refer to SELECTIVE CATALYTIC REDUCTION SYSTEM in SECTION 3 for more information.

NOTE: This USB connection should only be used by a trained service technician.

Refer to COMPUTER in SECTION 6 of the SERVICE MANUAL for more information and safeguards related to the use of this port.

28 ENGINE DIAGNOSTICS CONNECTION Plug a remote electronic diagnostic device into this connection such as a laptop computer with appropriate engine manufacturer’s programming to perform engine performance analysis and tuning.

IMPORTANT! Only use the battery disconnect switch to shut off a running machine in an emergency. A fault code will be logged by the ECM on the engine for improper shut down and power down.

NOTE: This operation can only be performed by a trained service technician.

2.18

Tigercat 726E Feller Buncher FUSES AND RELAYS

Controls and Operation

M726E-053

FUSE AND RELAY PANEL - CAB Each major circuit on the vehicle is protected against current overload by fuses. The fuses and relays are located in two places on the machine.

The Cab fuse and relay panel is located in the compartment just below the instrument panel as shown above. The main fuse and relay panel is located in the battery compartment in the right rear corner of the machine.

LABEL - MAIN FUSE AND RELAY PANEL ~ CAB 2.19

Tigercat 726E Feller Buncher

Controls and Operation

MAIN FUSE AND RELAY PANEL

BATTERY COMPARTMENT MAIN FUSE AND RELAY PANEL BATTERY COMPARTMENT M726E-105

This main fuse and relay panel is located in the electrical box in the battery compartment in the right rear corner of the machine.

LABEL, MAIN FUSE AND RELAY PANEL, BATTERY COMPARTMENT 2.20

Tigercat 726E Feller Buncher

Controls and Operation FIRE DETECTION SYSTEM COMPONENTS The Fire Detection System consists of the following main components:

FIRE DETECTION SYSTEM NOTE: This system is for FIRE DETECTION ONLY, it is not a fire suppression system.

In no way does the installation of this fire detection system reduce the need to adhere to the guidelines given in the FIRE PREVENTION section of this manual.

WARNING LIGHT

The fire detection system is only a warning system and will not extinguish a fire. If a fire is detected it must be extinguished manually using certified fire fighting equipment.

SYSTEM OPERATION There are 3 thermostats mounted in the engine and hydraulic area that are connected to the computer control system. The thermostats are automatic heat detection devices and are set to “close” at 177°C (350°F). When a thermostat closes it sends a signal to the computer which activates an audible alarm, flashing warning light and a visual warning on the computer screen indicating that a fire has been detected.

M726E-044

WARNING LIGHT AND BUZZER - In cab, warning light is on the instrument panel. The buzzer (not shown) is in the compartment below the instrument panel.

THERMOSTAT

M726E-134

IN CASE OF FIRE DETECTION ALARM: 1. Stop machine operation, park machine in a safe location and lower the load to the ground.

726E-076

HYDRAULIC PUMP COMPARTMENT

2. Shut down the engine.

HEAT THERMOSTAT - In hydraulic pump compartment

3. Remove the portable fire extinguisher from it's storage location.

4. Exit the cab immediately taking the fire extinguisher with you.

THERMOSTAT

5. Inspect the machine for cause of the Alarm.

Refer to "WHAT TO DO IN CASE OF A MACHINE FIRE" and "WHAT TO DO AFTER A FIRE" in SECTION 1 of this manual.

726E-074

ENGINE COMPARTMENT - L.H. SIDE

HEAT THERMOSTAT - L.H. side rear in engine compartment.

2.21

Tigercat 726E Feller Buncher

Controls and Operation Weekly:

THERMOSTAT

726E-075

ENGINE COMPARTMENT - R.H. FRONT HEAT THERMOSTAT - Over front of engine.

Inspect all parts for damage, rust, corrosion or dirt. Replace any damaged parts immediately.

•

All components are in place and unobstructed.

•

Check fire detection electrical network for cut, frayed, stripped or damaged wires.

•

Ensure thermostats are clean.

Every Month: • Turn ignition switch on. Next, use a heat source (heat gun) to apply heat to each of the thermostats (for approximately 30-40 seconds only) to confirm warning system light and buzzer operate and that the following message displays on the computer screen.

5 AMP FUSE

M726E-053

•

FUSE PANEL - IN CAB

ELECTRICAL POWER SUPPLY Power is supplied to the system by a 5 Amp fuse located in the fuse and relay panel.

M726E-134

SYSTEM TEST IMPORTANT! The following test is only to be performed on machines with Fire DETECTION system.

If this test is performed on machines with a fire SUPRESSION sytem it will activate the extinguishers.

KEEP TIP OF HEAT GUN BACK 76.2mm - 127mm (3"-5") HEAT GUN

APPLY HEAT TO THIS AREA ONLY.

Daily: •

THERMOSTAT

The following message will be displayed on the computer screen if there is a bad connection within the system. Repairs should be made immediately.

726E-018

WHEN TEST IS COMPLETE WIPE THERMOSTAT OFF WITH A COOL WET CLOTH.

HEAT TESTING THERMOSTAT USING A HEAT GUN

NOTE: DO NOT USE BUTANE TORCHES or any type of flame tool to heat test the sensors. The intense heat from a flame tool can damage the sensor.

M726E-135

2.22

Tigercat 726E Feller Buncher

Controls and Operation WARNING LIGHT

M726E-044

FIRE DETECTION WARNING LIGHT

726E-019

FIRE EXTINGUISHER

THERMOSTAT 726E-075

THERMOSTAT

THERMOSTAT 726E-074

HYDRAULIC COMPARTMENT - CENTER

ENGINE COMPARTMENT - L.H. SIDE 726E-054

FIRE DETECTION SYSTEM AND FIRE EXTINGUISHER LOCATION

AVOIDING DAMAGE AND FALSE SIGNALS DURING MACHINE SERVICE: Pay attention to the location of the components of the fire detection system. Take care not to damage heat sensors or wiring, this includes hitting, cutting, bending, denting, etc. Damage to heat sensors due to shock could make the system inoperable and/or cause false signals. Cut, pinched, or kinked wiring could make the system inoperable and/or cause false signals.

If any of the components are damaged, replace them immediately before operating the machine.

In addition thermostats are sensitive to heat from welding torches, steam cleaning or other outside sources which may create a false detection by the system.

FIRE PREVENTION

WARNING Failure to follow these instructions and guidelines may result in serious bodily injury, death, and property damage.

Refer to section 1 of this manual for FIRE PREVENTION information/techniques.

2.23

Tigercat 726E Feller Buncher OPERATOR’S SEAT - AIR RIDE

Controls and Operation RIDE ADJUSTMENT PROCEDURES After adjusting height, the ride adjustment should be made by pulling or pushing the air ride control valve knob.

SEAT ADJUSTMENTS

To Raise Push ride adjustment control to inflate air spring to obtain desired height.

To Lower Pull ride adjustment control to deflate air spring to obtain desired height.

LUMBAR HORIZONTAL ADJUSTMENT (NOT SHOWN) BACK ANGLE ADJUSTMENT

2-WAY ADJUSTABLE LUMBAR For fore-and-aft displacement, rotate HORIZONTAL ADJUSTMENT KNOB. BACK ANGLE ADJUSTMENT Rotate back angle adjustment knob to place seat at the desired angle.

FORE/AFT SLIDE Move and hold fore/aft slide lever. Roll seat forward or backward to the desired position relative to the footpedal controls.

RIDE ADJUSTMENT KNOB 720E-001

LUMBAR HORIZONTAL ADJUSTMENT

HEIGHT ADJUSTMENT LEVER FORE/AFT SLIDE LEVER

WARNING The seat belt supplied with this seat must be used at all times when operating this machine.

ARMREST ADJUSTMENT

ADJUSTMENTS HEIGHT ADJUSTMENT PROCEDURES The SPRING-ASSISTED height adjustment is controlled by the height adjustment lever located on the front left side of the seat chassis.

The four height settings: top, bottom and two inbetween, provide a total height adjustment of 3”.

332-6

VIEW FROM RIGHT REAR OF SEAT

ARMREST ADJUSTMENT Each armrest has 2 adjustments to place it in the required position. Loosen adjustment locking wingbolts to reposition armrest height and fore/aft position.

To Raise Firmly lift up on the height adjustment lever.

When the lever releases, hold it up while partially lifting the operator’s body weight from the seat.

When the seat is at the desired height, FIRMLY PUSH DOWN on the lever until the seat locks (a click should be heard).

To Lower Firmly lift up on the height adjustment lever.

When the lever releases, partially apply operator body weight to the seat until the seat is at the desired height. FIRMLY PUSH DOWN on the lever. Hold lever down until the seat locks into position (a click should be heard).

2.24

Tigercat 726E Feller Buncher

Controls and Operation RIDES TOO SOFT OR BOTTOMS OUT AND PINCHES OPERATOR The air ride control valve has under pressurized the seat air suspension ride adjustment Insufficient pressure exaggerates the knee-action movement of the seat. This usually happens because the operator is trying to lower the seat by decreasing the amount of air pressure instead of using the Height Adjustment lever. Refer to height adjustment.

BACK ANGLE ADJUSTMENT KNOB LUMBAR ADJUSTMENT

AIR RIDE ADJUSTMENT KNOB

SEAT TOO HIGH/SEAT TOO LOW There are several things which can cause improper seat height. Refer to the HEIGHT ADJUSTMENT and adjust seat to the desired position. If the proper height cannot be reached using one of the four height adjustment settings, it may be necessary to install the seat on a higher base.

FORE/AFT SLIDE LEVER M726E-033

SEAT ADJUSTMENTS

OPERATOR’S LEGS FALLING ASLEEP The seat is adjusted too high, and the air ride control valve has under pressurized the seat air suspension ride adjustment, resulting in the operator sitting in a “bucket”. Refer to height adjustment and RIDE ADJUSTMENT.

HEIGHT ADJUSTMENT LEVER

PROBLEMS AND CORRECTIVE ACTION RIDES TOO STIFF/SEAT TENDS TO PUSH OR THROW OPERATOR FORWARD The air ride control valve has over pressurized the seat air suspension. This typically happens because the operator is trying to use the air suspension to adjust the ride height rather than using height adjustment lever to raise the seat.

Refer to height adjustment.

2.25

Tigercat 726E Feller Buncher

Controls and Operation MD3 COMPUTER

COLOUR DISPLAY

ARROW (SCROLL) UP OK (ENTER) ARROW (SCROLL) DOWN

F1 M726E-096

F2

F3

F4

ESC (BACK)

MENU

MD3 COMPUTER, ELECTRONIC CONTROL AND MAIN DISPLAY

MD3 COMPUTER ELECTRONIC CONTROL & DISPLAY

MD3 COMPUTER

The MD3 computer, electronic control and display is the operator interface with the electronic control system. The MD3 is the central unit in the control system which works as both a master controller and a display unit. It has a 3.5" backlit colour graphic transflective display for reading system information.

The front of the MD3 consists of a control panel with a display and nine buttons. The buttons are arranged on the bottom and right hand side of the display.

• F1 through F4 function buttons,

,

,

, .

Programmed buttons that are configured by program software to bring up a display page, bring up an adjustment group or act as an input.

• Up and down arrow buttons

• OK button .

Pushing this button equals ’enter’. Saves the value or confirms the selection you have made.

• Menu button .

Always brings up the Menu page. It is not programmable.

.

• ’Esc’ or BACK button

Navigation buttons that are used to scroll thru selections on a menu page. The buttons are configured by program software to bring up a display page, bring up an adjustment group or act as a virtual input.

.

Returns you to the previous display page. May be configured by program software to bring up a display page, bring up an adjustment group or act as a virtual input.

2.26

Tigercat 726E Feller Buncher

Controls and Operation

1 2 8 9 5 7

726E-053

6

4

3

MD3 COMPUTER, SYSTEM MAIN COMPONENTS AND CONNECTIONS

MD3 COMPUTER CONTROL SYSTEM The MD3 computer control system is part of a network of components (shown above). The system is made up of the following components: 1.

2.

3.

4.

5.

6.

7.

8.

9.

MD3 Computer and Display Module Electronic Joystick Handles XA2 A1 Cab Expansion Module XA2 A2 Chassis Expansion Module Engine Electronic Control Module Pilot Manifold Electronic Solenoids Saw Control Valve Electronic Solenoids Denox Module Engine Electrical Control Unit Module (Tigercat FPT Cursor 8.7L) 10. Various controls, switches, and sensors not shown.

The MD3 computer is the main controller in the system. The MD3 computer program is the operating system for the computer display as well as the control system for the machine operating parameters.

NOTE: The computer control system is softwarebased. This software may be updated after the machine is in service as a part of on-going product improvement programs and service newsletters.

The information contained in this manual is accurate at the time of printing. Improvements to the machine and/or software are on-going and may not be covered. In these cases contact your Tigercat dealer for appropriate information.

3

M726E-123

INSIDE RIGHT CAB DOOR

As an example, the joystick handle button operations are transmitted to the MD3 controller electronically. These signals are then transmitted to the corresponding XA2 expansion module from the MD3 control and on to the corresponding control valve solenoid controls. The applicable hydraulic control valves will be activated allowing hydraulic oil to flow to the functions activated by the joystick movement.

4

The engine electronic control module provides electronic information to the MD3 computer via the J1939 CAN BUS link. This information is displayed on the computer display.

M726E-124

2.27

BEHIND CAB RIGHT SIDE

Tigercat 726E Feller Buncher 1

Controls and Operation

2

3

4

15

5

16 14 13

6

12

7 11

8

726E-056

9

10

MAIN MENU

MD3 COMPUTER MAIN MENU 1. INTERLOCK RESET - ON/OFF

9, INFORMATION MENU - Press F3 to select

2. PARK BRAKE - ON/OFF

10. ENGINE COOLANT TEMPERATURE

3. SAW INDICATOR - ON/OFF

11. ALARM INDICATORS - Press F4 to select

4. TIME AND DATE

12. OIL GRADE

5. SAW PRESSURE GAUGE

13. COLD OIL PROTECTION INDICATOR

6. ENGINE TACHOMETER RPM

14. HYDRAULIC OIL TEMPERATURE GAUGE

7. ENGINE MENU - Press F1 to select

15. FUEL LEVEL GAUGE

8. ADJUSTMENT MENU - Press F2 to select

16. DEF LEVEL INDICATOR

2.28

Tigercat 726E Feller Buncher

Controls and Operation Press the F2 button to toggle between metric and imperial units of measure.

ENGINE MENU

Press the F3 button to select the fuel information display.

Press the back button again to return to the main menu.

726E-052

From the main menu press the F1 button to select the engine display.

726E-055

The fuel information on display is as follows: • • • •

Fuel Rate - US gph or L/h (instantaneous) Total Fuel Used - US gal or L Trip Average Fuel Rate - US gal or L Trip Fuel Used - US gal or L Press the F3 button to reset the trip fuel used and trip average fuel rate functions.

Press the F2 button to toggle between imperial and metric units of measure.

Press the back button to return to the engine display.

726E-054

When selected the engine menu icon is on display and the engine functions will also be displayed.

Press the back button again to return to the main menu.

The engine functions on display are as follows: • • • • • • • • •

Engine Speed - rpm Percent Load Coolant Temperature - °F or °C Engine Oil Pressure - psi or bar Voltage - V Turbocharger Boost Pressure - psi or bar Charge Air Temperature - °F or °C Engine Hours Engine Oil Temperature - °F or °C

2.29

Tigercat 726E Feller Buncher

Controls and Operation To make changes to these settings Press F1 button to select the General Settings Menu from the ADJUSTMENT MENU.

ADJUSTMENT MENU

726E-052

726E-059

The General Settings menu appears on the display. The selections available are as follows:

From the main menu press F2 button to view the GENERAL SETTINGS.

• Oil Grade Selection • Fan Clean Frequency • Fan Clean Duration Use the arrow up/down buttons to scroll to the desired selection then press the OK button to make the selection.

SEE GENERAL SETTINGS later in THIS SECTION for more details.

726E-062

The current general settings that will be displayed. are as follows: •

Hydradulic Oil Grade

•

Fan Clean Frequency - minutes

•

Fan Clean Duration - seconds

2.30

Tigercat 726E Feller Buncher

Controls and Operation

GENERAL SETTINGS

726E-059 726E-052

Press the Menu button menu.

The General Settings menu appears on the display. The selections available are as follows:

to access the main

• Oil Grade Selection • Fan Clean Frequency • Fan Clean Duration Use the arrow up/down buttons to scroll to the desired selection then press the OK button to make the selection.

234E-092

From the main menu page press the F1 button (Adjust) to access the Adjust menu.

M726E-093

Use the arrow up/down buttons to scroll to General Settings then press the OK button to set selection.

2.31

Tigercat 726E Feller Buncher

Controls and Operation

OIL GRADE SELECTION

FAN CLEAN FREQUENCY

726E-060

726E-059

Scroll to the Oil Grade Selection in the General Settings menu. Press the OK button to make adjustments.

Scroll to the Fan Clean Frequency selection in the General Settings menu. Press the OK button to make adjustments.

M726E-094

726E-068

In the Oil Grade menu the available choices are: • ISO 22 • Petro Can MV 22 • ISO 32 • Petro Can MV 26 • ISO 46 • Esso Univis Ultra 46 • Petro Can MV 60 • ISO 68 Use the arrow up/down buttons to scroll to the desired selection then press the OK button to set selection.

The Fan Clean Frequency menu will appear.

The setting value can be adjusted between 5 minutes and 20 minutes. This is the setting for auto reverse of the cooling fan to go into the clean mode (reverse/clean) . The factory default setting is every 10 minutes. Press the arrow up or arrow down to scroll to the desired selection and press the OK button when desired value is selected.

Press the back button to return to the general settings menu or back button twice to return to the adjustment menu. Press the Back button again to return to the main menu.

Press the back button to return to the general settings menu or back button twice to return to the adjustment menu. Press the Back button again to return to the main menu.

2.32

Tigercat 726E Feller Buncher

Controls and Operation

COOLING FAN CLEAN DURATION

COLD OIL INDICATOR

1

726E-056

726E-061

Scroll to the Fan Clean Duration selection in the General Settings menu. Press the OK button to make adjustments.

A blue cold oil temperature Icon (1) will appear on the display when the hydraulic oil is at or below minimum temperature setting. When the oil warms the cold oil icon turns off.

IMPORTANT! To prevent damage to the machine, it is not recommended to run the attachment circuit or work the machine hard until the cold oil icon disappears.

726E-067

The Fan Clean Duration menu will appear.

The setting value can be adjusted between 10 seconds and 30 seconds. This is the time the cooling fan will remain in the clean (reverse/clean) mode. The factory default is 10 seconds. Press the arrow up or arrow down to scroll to the desired selection and press the OK button when desired value is selected.

Press the back button to return to the engine settings menu or back button twice to return to the adjustment menu. Press the Back button again to return to the main menu.

2.33

Tigercat 726E Feller Buncher

Controls and Operation CUTTER FUNCTIONS

INFORMATION MENU

Press the F1 button to select the Cutter Functions display from the Information Menu.

726E-052

726E-057

Press the F3 button to access the information menu.

The following information will be on display: • • • •

726E-058

When selected the information functions displayed are as follows: • Hydraulic Oil Temp -°F or °C • Cutter Pressure - psi or bar • Machine Hours - hrs • Machine Voltage - V • Saw Speed - rpm • Total Saw Hours - hrs Press the F2 button to toggle between imperial and metric units of measure.

Press the back button to return to the main menu.

2.34

Saw Pressure Gauge - psi or bar Engine Speed - rpm Hydraulic Oil Temp -°F or °C Engine Temp -°F or °C

Tigercat 726E Feller Buncher

Controls and Operation

MAIN MENU PAGE

PREFERENCES MENU

480-090

726E-052

Press the menu button menu page.

From the main menu page press the F3 button (Preferences) and the preferences menu page appears.

to go to the main

480-090

234-056

The following menu items can be selected.

The main menu page displays the following selections:

•

Display

•

Adjust - Select F1

•

Date/Time

•

Measure - Select F2

•

Language

•

Preferences - Select F3

•

Info - Select F4

To return to the Main menu press the back button.

2.35

Tigercat 726E Feller Buncher

Controls and Operation

DISPLAY ADJUSTMENT

SCREEN SAVER ADJUSTMENT

234-065

1075B-24

After selecting F1 the display adjustment screen opens and the following adjustments can be selected:

Select F3 to open the screen saver adjustment screen. Use the Arrow Up and Arrow Down buttons to scroll through the choices. Three choices are available:

RETURN TO MAIN MENU - Select F1 BACKLIGHT ADJUSTMENT - Select F2 SCREEN SAVER - Select F3 BACKLIGHT ADJUSTMENT

•

SCREEN SAVER OFF

•

DIMMED - Timeout 5 seconds

•

BLACK - Timeout 5 seconds

1075B-23 234-070

After selecting F2 the backlight adjustment screen opens. Use the Arrow Up or Arrow Down buttons to adjust the display backlight. The range is 10 to 100. The default setting is 100.

After making a selection press the OK button to confirm selection and press the back button to return to the main menu screen.

When the desired setting is selected press the OK button. A good rule to follow is the lower the number the longer the life of the display unit.

2.36

Tigercat 726E Feller Buncher

Controls and Operation

DATE/TIME ADJUSTMENT

DATE ADJUSTMENT

1075B-27

1075B-21

Press F2 to select the DATE/TIME adjustments in the PREFERENCES menu.

Press F1 to select DATE. Use the Arrow Up or Arrow Down to scroll through the YEAR list to select the year. Press OK to confirm year selected.

1075B-26 1075B-28

The DATE/TIME menu screen turns on. Two choices are available for adjustment:

When the year has been confirmed the display will highlight the MONTH. Use the Arrow Up or Arrow Down to select the month. Press OK to confirm month selected.

DATE - select F1 TIME - select F2

2.37

Tigercat 726E Feller Buncher

Controls and Operation

DATE ADJUSTMENT CONT’D

TIME ADJUSTMENT Select F2 Time adjustment from the DATE/TIME display screen.

1075B-29

1075B-34

When the month has been confirmed the display will highlight the DAY. Use the Arrow Up or Arrow Down to select the day. Press OK to confirm day selected.

The Time display screen will turn on. Use the Arrow Up or Arrow Down to select the HOUR. Press the OK button to confirm selection. The display will show the MINUTES highlighted.

1075B-26 1075B-35

The display will return to the DATE TIME menu.

Use the Arrow Up or Arrow Down to select the minute. Press OK button to confirm the selection.

The display will return to the DATE/TIME menu screen. Press the back button main menu screen.

2.38

to return to the

Tigercat 726E Feller Buncher

Controls and Operation

INFO MENU PAGE

MODULES

M726E-140

480-090

Press F1 to select the modules menu. This menu provides information on the following machine modules: • Display • XA2-A0-Module 1 - Cab • XA2-A2-Module 2 - Rear Chassis • Tigercat/FPT Cursor 8.7L • Denox Module (J1939-861)

From the main menu page press the F4 button

Press the back button (or F1) to return to the main menu page.

LOGS

M726E-141

(Info) and the Info menu page appears.

The following menu items can be selected.

•

Modules - Select F1

•

Logs - Select F3

The machine ID information will be displayed on the screen.

480-095

Press F3 from the info menu page to select logs.

This menu lists System Logs and Hydraulic Logs and the number of records within each log. The records are a list of all the fault occurrences in each log.

Use the Arrow Up or Arrow Down to select the menu item. Press OK to confirm the selection.

Press the back button (or F1) to return to the main menu page.

2.39

Tigercat 726E Feller Buncher MESSAGES

Controls and Operation

The MD3 computer displays messages, activates the master alarm and alarm light whenever a system fault occurs. Note that the computer control system will automatically perform a bulb test at engine start up to ensure that master alarm and alarm light are functioning. Refer to STARTING ENGINE in THIS SECTION. There are different types of Messages and Alarms, they appear on the screen as a block message.

The types of messages are: • CRITICAL MESSAGE - Colour RED • ALERT MESSAGE - Colour YELLOW • INFORMATION MESSAGE - Colour BLUE Messages can be hidden or acknowledged by pressing the F2 button (Hide or OK).

All messages that have been hidden or acknowledged are stored in the computer.

In some instances it will be necessary to immediately stop the machine, shut the engine OFF and repair the problem causing the message.

726E-056

Active fault messages that have been hidden can be reviewed by pressing the F4 button. Recalled messages and warnings will be displayed in order starting with the highest priority first.

2.40

Tigercat 726E Feller Buncher CRITICAL MESSAGES (RED)

Controls and Operation

Critical messages advise the operator that a critical machine fault is about to occur or a system fault has occurred.

Critical messages have the highest level of priority and are used to alert operator that immediate action must be taken to prevent damage to machine or to ensure operator safety.

When a critical message is displayed, the master alarm and alarm light will sound and flash continuously. The message remains on the screen until the operator hides it.

726E-053

Critical messages flash the critical symbol above the F4 button when active messages are hidden. The symbol will continue to flash until the problem is resolved and the fault becomes inactive.

Active messages that have been hidden can be reviewed by pressing the F4 button.

CRITICAL MESSAGE LIST: Hardware Fault - Engine Hydraulic Oil - Level Low. Hydraulic Oil - Temperature High Return Oil Filters - Bypassed Fire Detected Engine Stop - Critical Engine Fault Hardware Fault - MD3 Hardware Fault - XA2-A1 Hardware Fault - XA2-A2 Hardware Fault - Engine Fuel Filter Clogged Engine Coolant Temperature High Engine Coolant Level low Engine CAC Temperature High Engine Oil Pressure Low Diesel Exhaust Fluid Quality After Treatment System Technical Failure After Treatment System Engine Idle Too Long Engine Torque Derate Active Engine Locked Out Engine Restarts Remaining Until Engine Lockout Denox Fault Code Messages - Critical Engine Fault Code Messages - Critical Note: Not all messages are shown.

726E-064

The message will give brief details of the fault and advise what action is necessary.

In some instances the machine requires immediate action to correct the problem which requires the operator to STOP machine operation, SHUT THE ENGINE OFF and service the machine to correct the problem.

However, if the machine cannot be stopped immediately for safety reasons, the operator can hide the message. In this instance the machine should only be operated long enough to move the machine to a safe location, then STOP machine operation and SHUT THE ENGINE OFF before serious machine damage can occur!

Messages can be hidden by pressing the F2 button (Hide).

2.41

Tigercat 726E Feller Buncher CRITICAL MESSAGES

Controls and Operation HYDRAULIC OIL TEMPERATURE HIGH

HYDRAULIC OIL LEVEL LOW

Hydraulic Oil Hydraulic Oil

Temperature High.

Level Low.

This message will be displayed, alarm light will flash and alarm will sound when the oil temperature exceeds the recommended operating range for the type of hydraulic oil in use.

This message will be displayed, alarm light will flash and alarm will sound when the main hydraulic tank oil level is low.

If the temperature rises above the recommended operating range for the type of hydraulic oil in use check the following:

Stop the engine immediately when this alarm is activated. Operating machine with a low hydraulic oil level can cause hydraulic pumps to fail.

• • • • • •

When this alarm is activated stop the engine and look for signs of broken hoses or other leaks.

Repair leaks and refill the main hydraulic tank to FULL mark on the monitor display gauge. Restart engine and inspect for leaks.

Plugged oil cooler Malfunction in a hydraulic system High loads on the hydraulic system Malfunction of the cooling fan Low hydraulic oil level Correct Hydraulic Oil Grade Selection

If hydraulic oil temperature rises above the recommended operating range DO NOT continue to operate the machine.

This alarm must not be used to monitor the hydraulic oil. The operator must use the hydraulic oil temperature gauge on the main menu, together with the operating range chart in SECTION 3 to prevent damage to the hydraulic system.

Hydraulic oil grade information is shown on the main menu below the hydraulic oil temperature gauge.

Operating outside the recommended operating range will shorten hydraulic component life.

Refer to COMPUTER ~ ADJUSTMENT MENU SERVICE SETTINGS ~ HYDRAULIC OIL GRADE in THIS SECTION for hydraulic oil grade selection settings information.

Refer also to APPROVED HYDRAULIC OILS in SECTION 3 of THIS MANUAL for hydraulic oil operating range information.

Refer to COMPUTER ~ INFORMATION MODE MENU ~ HYDRAULIC OIL TEMPERATURE in THIS SECTION for hydraulic oil temperature information display.

2.42

Tigercat 726E Feller Buncher

Controls and Operation

ENGINE STOP

HARDWARE FAULT - XA2

Engine Stop

Hardware Fault - XA2

Critical engine fault active - contact service.

Active fault has been hidden. Turn key off and on to recall active hidden hardware faults.

This message will be displayed, alarm light will flash and alarm will sound when critical engine alarms are triggered. STOP ENGINE.

This message will be displayed, alarm light will flash and alarm will sound when a critical active hardware fault related to the XA2 module has been hidden.

Refer to engine manufacturer's manual for specific information regarding the engine.

To recall the original active fault(s) the operator must turn the key off and on.

HARDWARE FAULT - MD3

A VREF (modules reference voltage) and no contact errors are examples of the type of hardware fault which may be the original active fault which triggers this message.

Hardware Fault - MD3 Active fault has been hidden. Turn key off and on to recall active hidden hardware faults.

HARDWARE FAULT - ENGINE

Hardware Fault - Engine Active fault has been hidden. Turn key off and on to recall active hidden hardware faults.

This message will be displayed, alarm light will flash and alarm will sound when a critical active hardware fault related to the MD3 Display module has been hidden.

To recall the original active fault(s) the operator must turn the key off and on.

This message will be displayed, alarm light will flash and alarm will sound when a critical active hardware fault related to the Engine has been hidden.

A VREF (modules reference voltage) error is an example of the type of hardware fault which will be the original active fault which triggers this message.

To recall the original active fault(s) the operator must turn the key off and on.

No contact error is an example of the type of hardware fault which may be the original active fault which triggers this message.

2.43

Tigercat 726E Feller Buncher

Controls and Operation

HARDWARE FAULT - DENOX MODULE

ENGINE FAULT CODE MESSAGES - CRITICAL

Hardware Fault - Denox module

SPN: 0 FMI: 0 1 of 1

Active fault has been hidden. Turn key off and on to recall active hidden hardware faults.

Engine fault parameter - Fault Identifier

This message will be displayed, alarm light will flash and alarm will sound when a critical active hardware fault related to the Denox Module has been hidden.

Critical engine fault message(s) will be displayed, alarm light will flash and alarm will sound when a critical engine fault message is received from the engine electronic control module.

To recall the original active fault(s) the operator must turn the key off and on.

They provide the SPN code (suspect parameter number) and the FMI code (fault mode identifier) as well as a message describing the fault (when available).

No contact error is an example of the type of hardware fault which may be the original active fault which triggers this message.

Critical engine fault codes are higher priority messages than alert level engine fault code messages. Critical messages can be hidden but immediate action must be taken, STOP machine operation and service engine immediately to resolve the cause of the fault.

An example of a critical engine fault message is shown above.

Note that some less common engine fault codes will appear without a message describing the fault. Make a note of the SPN and FMI codes and contact service for more information.

Refer to engine manufacturer's manual for specific information regarding the engine.

2.44

Tigercat 726E Feller Buncher

Controls and Operation

ENGINE OIL PRESSURE LOW

ENGINE FAULT CODE MESSAGES - CRITICAL

SPN: 131128 FMI: 12 1 of 1

SPN: 65590 FMI: 3 1 of 1

Engine Oil Pressure Low.

Contact dealer.

This message will be displayed, alarm light will flash and alarm will sound when engine oil pressure falls below 10psi (0.7 bar).

Critical engine fault message(s) will be displayed, alarm light will flash and alarm will sound when a critical engine fault message is received from the engine electronic control module.

Stop the engine when this alarm is activated.

Check engine oil levels.

They provide the SPN code (suspect parameter number) and the FMI code (fault mode identifier) as well as a message describing the fault (when available).

Refer to STARTING ENGINE in THIS SECTION for more information.

ENGINE OIL TEMPERATURE HIGH

Critical engine fault codes are higher priority messages than alert level engine fault code messages. Critical messages can be hidden but immediate action must be taken, STOP machine operation and service engine immediately to resolve the cause of the fault.

SPN: 131130 FMI: 12 1 of 1 Engine oil temperature high.

An example of a critical engine fault message is shown above.

Note that some less common engine fault codes will appear without a message describing the fault. Make a note of the SPN and FMI codes and contact service for more information.

This message will be displayed, alarm light will flash and alarm will sound when engine oil temperature exceeds recommended engine temperature.

Refer to engine manual for specific information regarding the engine and aftertreatment system.

NOTE: Contact your Tigercat dealer to obtain an Engine Fault Codes chart. An up to date copy should be kept in the Manual’s Box (in the cab). The chart is updated regularly by the engine manufacturer, so it is important to check periodically with the Tigercat dealer to ensure that you have a current copy of the Engine Fault Codes chart.

Check the cooling assembly and fan for proper operation and run a clean cycle if the machine is equipped with a variable pitch fan. It is also important to manually clean debris from the machine on a regular basis to maintain low machine operating temperatures. Refer to CLEANING A/C CONDENSER AND COOLING ASSEMBLY in THIS SECTION. Refer to Engine manuals for more information.

2.45

Tigercat 726E Feller Buncher

Controls and Operation

DIESEL EXHAUST FLUID QUALITY

Diesel Exhaust Fluid

SPN: 262173 1 of 1

Quality warning severe. Engine lockout will occur after full torque derate and 3 engine restarts.

DEF quality low.

This message will be displayed, alarm light will flash and alarm will sound when a diesel fluid quality problem is detected. Action to correct the problem should be taken immediately to avoid affecting engine performance and damage to the selective catalytic reduction (SCR) after treatment system components.

WARNING Use only diesel exhaust fluid (DEF) which meets ISO 22241 specifications. DEF fluid is sprayed into the exhaust system at high temperatures during normal operation of the Selective Catalytic Reduction (SCR) after treatment system.

This message results in the following derate and engine lockout sequence if no action is taken to correct the problem:

NEVER fill the DEF tank with any other fluid.

Doing so may cause a fire risk which could result in death or serious injury.

•

Beginning 1 hour after a DEF quality message there will be a ramp down of Engine Speed by 60% and Torque by 65% over 40 minutes.

• After 2 hours at derated engine speed and torque the engine is derated to idle within 30 minutes.

• A total of 3 restarts are allowed after any derate has started. Refer to COMPUTER~MESSAGES - CRITICAL~ENGINE LOCKED OUT and ENGINE RESTARTS REMAINING UNTIL ENGINE LOCKOUT in THIS SECTION. To correct the DEF quality problem clean the area around the DEF tank then drain and refill the tank with clean DEF which meets ISO 22241 specifications.

Additional messages from the Denox Module will also be displayed. Refer to Engine Manuals for code information.

Note that an Engine Torque Derate Active message will also be triggered as the engine begins to derate. Refer to COMPUTER~ MESSAGES - CRITICAL ~ ENGINE TORQUE DERATE ACTIVE. Refer to DIESEL EXHAUST FLUID TANK in SECTION 2 of THIS MANUAL and DRAINING DEISEL EXHAUST FLUID TANK in SECTION 3 of THIS MANUAL. Refer also to SELECTIVE CATALYTIC REDUCTION SYSTEM in SECTION 3 of THIS MANUAL for more information regarding the use of DEF and its function in the SCR after treatment system.

2.46

Tigercat 726E Feller Buncher

Controls and Operation

DENOX FAULT CODE MESSAGES - CRITICAL

AFTER TREATMENT SYSTEM TECHNICAL FAILURE

SPN: 15### FMI: # 1 of 1

After Treatment System

Contact dealer.

Technical failure severe. Engine lockout will occur after full torque derate and 3 engine restarts.

Critical Denox DCU fault message(s) will be displayed, alarm light will flash and alarm will sound when a critical Denox DCU fault message is received from the Denox module.

This message will be displayed, alarm light will flash and alarm will sound when an after treatment technical fault is detected. Action to correct the problem should be taken immediately to avoid affecting engine performance and damage to the selective catalytic reduction (SCR) after treatment system components.

They provide the SPN code (suspect parameter number) and the FMI code (fault mode identifier) as well as a message describing the fault (when available).

This message results in the following derate and shutdown sequence if no action is taken to correct the problem:

Critical Denox DCU fault codes are higher priority messages than alert level Denox DCU fault code messages. Critical messages can be hidden but immediate action must be taken, STOP machine operation and service engine immediately to resolve the cause of the fault.

An example of a critical Denox DCU message is shown above.

Note that some less common Denox DCU fault codes will appear without a message describing the fault. Make a note of the SPN codes and contact service for more information.

Refer to engine manual for specific information regarding the engine and aftertreatment system.

NOTE: Contact your Tigercat dealer to obtain an Denox DCU Codes chart. An up to date copy should be kept in the Manual’s Box (in the cab). The chart is updated regularly by the engine manufacturer, so it is important to check periodically with the Tigercat dealer to ensure that you have a current copy of the Denox DCU Codes chart.

•

Beginning immediately after an after treatment system technical warning there will be a a ramp down of Torque by 25% over 25 minutes.

•

After 1 hour at reduced torque there will be a ramp down of Engine Speed by 60% and Torque by 65% over 40 minutes.

•

After 2 hours at derated engine speed and torque the engine is derated to idle within 30 minutes.

•

A total of 3 restarts are allowed after any derate has started. Refer to COMPUTER~MESSAGES CRITICAL~ENGINE LOCKED OUT and ENGINE RESTARTS REMAINING UNTIL ENGINE LOCKOUT in THIS SECTION.

Identify the cause of the technical failure and take action to correct the problem.

Refer also to SELECTIVE CATALYTIC REDUCTION SYSTEM in SECTION 3 of THIS MANUAL for more information.

2.47

Tigercat 726E Feller Buncher

Controls and Operation ENGINE LOCKED OUT

AFTER TREATMENT SYSTEM ENGINE IDLE TOO LONG

Engine

After Treatment System

Engine locked out. Engine derate to 0% Torque and 850 rpm. Contact Dealer

Engine idle too long. Shutdown engine to prevent damage to emission control system.

This message will be displayed, alarm light will flash and alarm will sound when an engine is automatically shutdown by the computer system to prevent further damage to the engine and after treatment system.

This message will be displayed, alarm light will flash and alarm will sound when this engine has idled for more than 4 consecutive hours.

Shutdown engine to prevent damage to the emission control system.

Note that an engine is locked out after several other critical after treatment system messages regarding the cause of the problem and additional messages regarding the number of restarts until engine lockout.

IMPORTANT !

Engine should not idle longer than 4 consecutive hours. Damage to the emission control system will result. When this machine idles for an extended period excess hydrocarbon buildup is created in the SCR after treatment system. Burn off of excess hydrocarbon at full load immediately after a long idle period will generate excess heat which will cause damage to emission control system components. It will take 45 minutes at 40% load (or an SCR exhaust outlet temperature of 320°C (608°F)) to burn off the hydrocarbon that accumulates during a 4 hour long idle.

Once locked out the engine will stop and all DEF solution will be pumped back to tank before the engine power system is turned off. This process takes approximately 90 seconds. After engine shut down is complete the engine can be started with full power for only 30 seconds before derating to idle. Action to correct the original cause(s) of the lockout must be taken before the engine can be reset. Contact dealer to reset engine for normal operation.

ENGINE TORQUE DERATE ACTIVE

SPN: 327773 FMI: 3 1 of 1

SPN: 65615 FMI: 1 1 of 1

ATS Inducment engine lockout

Engine torque derate activeBelow normal, most severe

Additional messages from the Denox Module will also be displayed. Refer to Engine Manuals for code information.

This message will be displayed, alarm light will flash and alarm will sound when the Denox Module has derated the engine. The code for a Torque Derate / Diesel Exhaust Fluid Empty is shown above as an example.

Refer also to COMPUTER~MESSAGES CRITICAL~ENGINE RESTARTS REMAINING UNTIL ENGINE LOCKOUT in THIS SECTION.

Refer to Engine Manuals for code information to identify the cause(s) of engine derating and more information regarding failure cause and repair.

2.48

Tigercat 726E Feller Buncher ENGINE RESTARTS REMAINING UNTIL ENGINE LOCKOUT

Controls and Operation HYDRAULIC OIL RETURN FILTERS BYPASSED

Return Oil Filters

Engine

Bypassed. Slowly warm up machine or service if already warm..

3 restarts remaining until engine lockout.

This message will be displayed, alarm light will flash and alarm will sound to inform the operator of the number of restarts available before the engine is locked out.

Note that an engine is locked out after several other critical after treatment system messages regarding the cause of the problem and this message regarding the number of restarts until engine lockout.

This message will be displayed, alarm light will flash and alarm will sound to inform the operator that the hydraulic oil return filters have been bypassed.

This message may appear if the machine is cold.

If the machine has already been warmed up then the filters have been bypassed and the machine should be service immediately.

Refer also to COMPUTER~MESSAGES CRITICAL~ENGINE LOCKED OUT in THIS SECTION.

2.49

Tigercat 726E Feller Buncher ALERT MESSAGES (YELLOW)

Controls and Operation There are two types of alert messages:

Alert messages advise the operator that machine operation will be compromised.

Alert messages have the second level of priority and are used to indicate to the operator that action is required to prevent future damage to the machine.

All alert message will give brief details of the fault and advise what action is necessary.

Action should be taken to service the machine to correct the problem at the earliest opportunity to prevent future damage to the machine.

Alert programmed messages generally triggered by machine function related conditions.

When an alert message is displayed, the external alarm and light will sound and flash three times to alert the operator of the message. The message remains on the screen until the operator hides it.

Messages can be hidden by pressing the F2 button (Hide).

726E-065

Alert messages flash the alert symbol above the F4 button when active messages are hidden.

Alert computer system generated messages are generally triggered by computer system error and fault related conditions.

Active messages that have been hidden can be reviewed by pressing the F4 button. The symbol will continue to flash until the problem is resolved and the fault becomes inactive.

When a system generated alert message is displayed the external alarm and light will sound and flash three times to alert the operator of the message.

Note that if both a critical level fault and an alert level fault are present the critical symbol will take priority until the critical fault becomes inactive.

The message remains on the screen until the operator hides it.

Note that active hardware fault alert messages are acknowledged by pressing the F2 button (OK). To recall these messages turn key off and on. On screen messages will indicate to the operator that an active hardware fault has been hidden.

2.50

Tigercat 726E Feller Buncher

Controls and Operation

INTERACTIVE ALERT MESSAGES •

Engine Air Intake Filter Restricted

•

Drive Charge Filter Bypassed

•

Fire Detection System Malfunction

•

Machine Voltage High

•

Fuel Level Low

•

Machine Voltage Low

•

Hardware Fault – MD3

•

Hardware Fault COUT

•

Hardware Fault DIN

•

Hardware Fault DOUT

•

Hardware Fault VIN

•

Hardware Fault XA2-A1

•

Hardware Fault XA2-A2

•

Engine Fault Code Messages

•

Diesel Exhaust Fluid Level <10%

•

Diesel Exhaust Fluid Level <5%

•

Diesel Exhaust Fluid Level Empty

•

Denox Fault Code Messages

•

Module MD3

ENGINE FAULT CODE MESSAGES

Engine

Engine fault active - contact service

726E-066

SPN: 110 FMI: 16 1 of 1 Engine coolant temperature high Above normal, severe

Note: Not all system generated alert messages are shown.

Alert engine fault message(s) will be displayed, alarm light will flash and alarm will sound when an alert engine fault message is received from the engine electronic control module.

They provide the SPN code (suspect parameter number) and the FMI code (fault mode identifier) as well as a message describing the fault (when available).

Alert engine fault codes are lower priority messages than critical level engine fault code messages. Alert messages can be hidden but action (service engine) is required to resolve the cause of the fault.

An example of an alert engine fault message is shown above.

Note that some less common engine fault codes will appear without a message describing the fault. Make a note of the SPN and FMI codes and contact service for more information.

Refer to engine manufacturer's manual for specific information regarding the engine.

2.51

Tigercat 726E Feller Buncher

Controls and Operation

DRIVE CHARGE FILTER BYPASS

HARDWARE FAULT - MD3

Drive Charge Filter

Hardware Fault - MD3

Bypassed. Service machine to correct.

Active fault has been hidden. Turn key off and on to recall active hidden hardware faults.

This message will be displayed when an alert level active fault related to the DRIVE CHARGE FILTER BYPASS has been triggered.

This message will be displayed when an alert level active hardware fault related to the MD3 Display module has been hidden.

Restricted. Service machine alert message is an example of the type of fault that triggers this message. The charge pressure filter is restricted and requires service or the oil temperature is cold allowing the filter to be bypassed.

To recall the original active fault(s) the operator must turn the key off and on.

High temperature, low supply voltage and high supply voltage module alert messages are examples of the type of hardware fault which will be the original active faults which trigger this message.

HARDWARE FAULT - XA2

Hardware Fault - XA2-A0 Active fault has been hidden. Turn key off and on to recall active hidden hardware faults.

This message will be displayed when an alert level active hardware fault related to the XA2-A0 module has been hidden.

To recall the original active fault(s) the operator must turn the key off and on.

High temperature, low supply voltage and high supply voltage module alert messages are examples of the type of hardware fault which will be the original active faults which trigger this message.

2.52

Tigercat 726E Feller Buncher

Controls and Operation

DIESEL EXHAUST FLUID LEVEL MESSAGES

DIESEL EXHAUST FLUID LEVEL EMPTY

There are three levels of diesel exhaust fluid level messages generated by the Denox Module.

DIESEL EXHAUST FLUID LEVEL <10%

SPN: 15765 FMI: 7 1 of 1 DEF tank empty.

SPN: 15851 FMI:1 1 of 1 DEF Level below 10%.

This message will be displayed, alarm light will flash and alarm will sound when diesel exhaust fluid level empty is detected. Action to correct DEF levels should be taken immediately to avoid affecting engine performance and damage to the selective catalytic reduction (SCR) after treatment system components.

This message will be displayed, alarm light will flash and alarm will sound when a diesel exhaust fluid level below 10% is detected. Action to correct DEF levels should be taken immediately to avoid affecting engine performance and damage to the selective catalytic reduction (SCR) after treatment system components.

•

Beginning immediately after a DEF level empty message, the engine is derated to idle within 30 minutes.

Fill DEF tank and restart engine to clear the message.

Fill DEF tank and restart engine to clear the warning.

Note that an Engine Torque Derate Active message will also be triggered as the engine begins to derate. Refer to COMPUTER~ MESSAGES AND WARNINGS - CRITICAL ~ ENGINE TORQUE DERATE ACTIVE.

Refer to DIESEL EXHAUST FLUID TANK in SECTION 2 of THIS MANUAL. DIESEL EXHAUST FLUID LEVEL <5%

FUEL - WATER IN FUEL

SPN: 15852 FMI:1 1 of 1 DEF Level below 5%.

SPN: 65564 FMI: 3 1 of 1 Water in Fuel.

This message will be displayed, alarm light will flash and alarm will sound when a diesel exhaust fluid level below 5% is detected. Action to correct DEF levels should be taken immediately to avoid affecting engine performance and damage to the selective catalytic reduction (SCR) after treatment system components.

•

This message will be displayed when water is detected in the fuel by the engine computer system.

Refer to engine manufacturer's manual for specific information regarding the engine.

Beginning immediately after a DEF level <5% warning, there will be a ramp down of Engine Speed by 60% and Torque by 65% over 40 minutes.

Fill DEF tank and restart engine to clear the message.

2.53

Tigercat 726E Feller Buncher

Controls and Operation

ENGINE FAULT CODE MESSAGES

DENOX FAULT CODE MESSAGES

SPN: ###### FMI: # 1 of 1

SPN: 15### FMI: # 1 of 1

Contact dealer.

Contact dealer.

Alert engine fault message(s) will be displayed, alarm light will flash and alarm will sound when an alert engine fault message is received from the engine electronic control module.

Alert Denox DCU message(s) will be displayed, alarm light will flash and alarm will sound when an alert Denox DCU message is received from the Denox module.

They provide the SPN code (suspect parameter number) and the FMI code (fault mode identifier) as well as a message describing the fault (when available).

They provide the SPN code (suspect parameter number) and the FMI code (fault mode identifier) as well as a message describing the fault (when available).

Alert engine fault codes are lower priority messages than critical level engine fault code messages. Alert messages can be hidden but action (service engine) is required to resolve the cause of the fault.

Alert Denox DCU codes are lower priority messages than critical level Denox DCU code messages. Alert messages can be hidden but action (service after treatment system) is required to resolve the cause of the fault.

An example of an alert engine fault message is shown above.

An example of an alert Denox DCU message is shown above.

Note that some less common engine fault codes will appear without a message describing the fault. Make a note of the SPN and FMI codes and contact service for more information.

Note that some less common Denox DCU codes will appear without a message describing the fault. Make a note of the SPN codes and contact service for more information.

Refer to engine manual for specific information regarding the engine and after treatment system.

Refer to engine manual for specific information regarding the engine and after treatment system.

NOTE: Contact your Tigercat dealer to obtain an Engine Fault Codes chart. An up to date copy should be kept in the Manual’s Box (in the cab). The chart is updated regularly by the engine manufacturer, so it is important to check periodically with the Tigercat dealer to ensure that you have a current copy of the Engine Fault Codes chart.

NOTE: Contact your Tigercat dealer to obtain an Denox DCU Codes chart. An up to date copy should be kept in the Manual’s Box (in the cab). The chart is updated regularly by the engine manufacturer, so it is important to check periodically with the Tigercat dealer to ensure that you have a current copy of the Denox DCU Codes chart.

2.54

Tigercat 726E Feller Buncher SERVICE COMPARTMENTS, DOORS AND ACCESS PANELS

Controls and Operation

REAR DOOR

726E-079

DOOR SAFETY STOP IN LOCK OPEN POSITION

Lift the door safety stop out of it's storage position and place the safety stop bolt in hole provided in the door ledge to brace the door open. Reverse this procedure to close doors.

RIGHT SIDE COMPARTMENTS, DOORS AND ACCESS PANELS 9

726E-077

6

5

4

2

7

The rear door provides access to the engine air filter, hydraulic pumps, hydraulic oil return filters, charge pressure filter, hydraulic oil sight gauge, hydraulic oil fill button and hose and the fuel filter/ water separator.

8

AIR INTAKE PRECLEANER ACCESS

M726E-065

3

1

The following compartments, doors and access panels are located on the right side of the machine: 1. Cab door, R.H. 2. Cooling fan and motor access, hinged door.

3. Cooling fan and motor access, removable panel.

4

Engine compartment access, hinged door.

5

Engine compartment access, removable panel.

6. Pump drive gearbox dipstick, engine fuel filter and starter motor access, hinged door.

726E-072 M726E-104

7. Master disconnect switch access, hinged door.

To open the door, swing the latch pin stop to the side, lift up the pin and swing open the door.

8. Battery compartment, removable panel.

9. Diesel fuel fill hinged cover.

2.55

Tigercat 726E Feller Buncher

Controls and Operation

OPENING THE RIGHT HAND DOORS 9

6

5

4

LEFT SIDE COMPARTMENTS, DOORS AND ACCESS PANELS

2

11

13

14

15

7 16 8 17

M726E-065

3

1 M726E-064

The right hand cab door (1) is an emergency exit but also gives access to the AC/heater unit and inside the control panel.

10

12

The following compartments, doors and access panels are located on the left side of the machine:

The cooling fan and motor upper door (2) is hinged. To open the door, swing the latch pin stop to the side, lift up the pin and swing open the door.

10. Cab door, L.H. 11. Cooling package access, hinged door.

12. Cooling package access, removable panel.

The cooling fan and motor lower panel (3) is removable and held in place by the upper hinged door. Fully open the upper hinged door to allow the lower panel to be removed.

13 Engine compartment access, hinged door.

14 Engine compartment access, removable panel.

The engine compartment upper door (4) is hinged.

To open the door, swing the latch pin stop to the side, lift up the pin and swing open the door.

15. Alternator and engine CPU access, hinged door.

The engine compartment lower panel (5) is removable and held in place by the upper hinged door. Fully open the upper hinged door to allow the lower panel to be removed.

17. DEF Tank and supply module access, removable panel.

16. DEF Tank fill access, hinged door.

To open the pump drive gearbox dipstick access door (6) and master disconnect switch access door (7), pull on the latch handles and swing the doors open.

To access the battery compartment (8) remove the panel mounting screws and remove the panel.

2.56

Tigercat 726E Feller Buncher

Controls and Operation

OPENING THE LEFT HAND DOORS 11

13

14

15

16

17

M726E-064

10

12

The left hand cab door (10) is the main access to the cab.

The cooling package upper door (11) is hinged. To open the door, swing the latch pin stop to the side, lift up the pin and swing open the door.

The cooling package lower panel (12) is removable and held in place by the upper hinged door. Fully open the upper hinged door to allow the lower panel to be removed.

The engine compartment upper door (13) is hinged. To open the door, swing the latch pin stop to the side, lift up the pin and swing open the door.

The engine compartment lower panel (14) is removable and held in place by the upper hinged door. Fully open the upper hinged door to allow the lower panel to be removed.

To open the alternator and engine CPU access door (15) and DEF tank fill access door (16), pull on the latch handles and swing the doors open.

To access the DEF Tank and supply module compartment (17) remove the panel mounting screws and remove the panel.

2.57

Tigercat 726E Feller Buncher

Controls and Operation REFUELING

FUEL TANK

Park machine on level ground, shut off engine and allow machine to cool.

FUEL LEVEL SENDER

FUEL FILL CAP

FUEL TANK

DO NOT refuel while smoking or near an open flame or sparks.

Clear obstructions from steps and handles needed to access fuel tank.

Open cover on top of fuel tank (if equipped)and clear any debris from around the fill cap.

M726E-065

Remove filler cap slowly to allow pressure to escape from tank.

Located at the right rear of the machine, the fuel tank has a capacity of 416 L (110 gal). The fuel filler cap and fuel level sender are located under a hinged cover on the top of the tank. The fuel level sender sends a signal to the computer system which displays an on screen fuel level gauge.

Inspect fill cap gasket.

Inspect fuel strainer located under the fill cap for debris or damage.

Attach a grounding strap to an unpainted metal surface on the machine if the refueling tank or nozzle is so equipped.

2 DIPSTICK

Fill tank until fuel level reaches the strainer or the full mark on the sight gauge if equipped. Do not leave nozzle unattended or spillage may occur.

Remove nozzle and ground strap (if applicable), then install fill cap hand tight before closing fill cap cover.

Before restarting the machine, check that no other personnel have moved into the hazardous area and sound the horn.

FILTER SCREEN

718E-037

FUEL TANK DIPSTICK/FILTER SCREEN A dipstick and filler screen under the filler cap.

The dipstick slides through a hole in the side of the filler screen. DO NOT drop the dipstick into the filler tube or it will punch a hole in the bottom of the filler screen. The filler screen should be removed and cleaned every 125 hours (reach in and lift it out). Replace the screen if it is damaged.

S≤15 mg/kg ULTRA LOW SULFUR FUEL ONLY 36686AUNI R0

2.58

Tigercat 726E Feller Buncher

Controls and Operation

DIESEL EXHAUST FLUID (DEF) TANK The DEF tank is located in the compartment in front of the hydraulic tank in the left rear corner of the machine. The DEF tank fill cap can be accessed through the hinged door on the front of that compartment. The DEF tank fill point is equipped with a filter to prevent contaminants from entering the tank.

DEF TANK (BLUE FILL CAP)

41581AUNI R0

DEF tank capacity is 43 L (11.4 US gal). DO NOT overfill tank. This tank is equipped with an expansion capacity of 7% required to allow for the expansion of DEF in cold temperature conditions.

DEF freezes at -11°C (12°F).

A DEF level indicator is shown on the main menu of the computer display, below the fuel gauge.

M726E-070

DEF TANK

When DEF levels are low information messages and warnings will be shown on the computer display. Note that extremely low DEF levels may result in derating of engine performance to meet emission standard requirements. Action to correct DEF levels should be taken immediately to avoid affecting engine performance. Refer also to COMPUTER~MESSAGES AND WARNINGS in THIS SECTION.

DEF is used by the Selective Catalytic Reduction (SCR) after treatment system to lower the concentration of nitrogen oxides from the diesel engine exhaust of this vehicle.

The DEF tank and DEF supply lines are heated when temperatures are low, the system will thaw DEF within 30 minutes of engine start for proper operation of the SCR after treatment system.

Note also that whenever the engine is stopped all DEF is pumped back to tank before the engine power system is turned off. This process takes approximately 90 seconds. Refer to SELECTIVE CATALYTIC REDUCTION SYSTEM in SECTION 3 of THIS MANUAL.

When a problem with DEF quality is detected information messages and warnings will be shown on the computer display. Note that DEF quality problems may result in derating of engine performance to meet emission standard requirements. Action to correct DEF quality problems should be taken immediately to avoid affecting engine performance and damage to SCR after treatment system components. Refer also to COMPUTER~MESSAGES AND WARNINGS in THIS SECTION.

It is important to avoid contamination of DEF when filling the tank as this may cause costly damage to SCR system components and affect the proper operation of the SCR system and the engine.

Diesel exhaust fluid (DEF) is an aqueous urea solution with 32.5% high purity urea and 67.5% deionized water. Note that DEF may also be referred to as AUS32 or AdBlue and should meet ISO 22241 specifications. Use only DEF meeting this standard.

IMPORTANT! DEF should be stored between -11°C (12°F) and 30°C (86°F) and out of direct sunlight to maximize shelf life and to avoid DEF quality problems caused by improper storage.

Refer also to SELECTIVE CATALYTIC REDUCTION SYSTEM in SECTION 3 of THIS MANUAL for more information regarding the use of DEF and its function in the SCR after treatment system.

WARNING Use only diesel exhaust fluid (DEF) which meets ISO 22241 specifications. DEF fluid is sprayed into the exhaust system at high temperatures during normal operation of the Selective Catalytic Reduction (SCR) after treatment system.

NEVER fill the DEF tank with any other fluid.

Doing so may cause a fire risk which could result in death or serious injury.

2.59

Tigercat 726E Feller Buncher

Controls and Operation

HYDRAULIC OIL TANK

BREATHER

SIGHT GAUGE HYD. OIL LEVEL

SENDING UNIT LOW HYDRAULIC OIL

RETURN FILTERS

Located at the left rear of the machine, the hydraulic tank has a capacity of 178 L (47 gal).

A sight gauge, accessible through the rear door indicates the HIGH and LOW levels of the hydraulic oil. A low level sending unit is installed in the tank that signals a “low hydraulic oil” light in the cab to come ON when the oil level is low.

Always keep the hydraulic oil between the HIGH and LOW calibrations.

A low hydraulic oil level can result in severe damage to pumps.

Over filling causes the excess oil to discharge from the breather vent.

2.60

Tigercat 726E Feller Buncher

Controls and Operation

HYDRAULIC OIL FILL PUMP

FILL HOSE STORED OIL FILL ACTIVATION BUTTON

FILL HOSE QUICK CONNECTION

726E-079

HYDRAULIC OIL FILL

The hydraulic oil fill pump is used for adding oil to the hydraulic oil tank. It is located in the right hand side of the rear chassis under the cooler package.

ELECTRIC HYDRAULIC OIL FILL PUMP

The activation button is located at the rear of the machine in the hydraulic compartment on the hydraulic oil return filter bracket and the fill hose quick connection is located in the bottom right corner of the rear hydraulic compartment.

The fill hose/suction tube is stored on the inside of the rear hydraulic compartment door.

To add oil to the tank, remove fill hose from storage and connect it to the quick connection on the chassis. Clean suction tube and remove cap.

Insert end of suction tube into supply drum and push and hold the activation button to operate the pump. The oil is pumped directly into the hydraulic tank via a return filter.

M726E-090

Release the button when the tank is full. Do not allow the supply tank to run dry while the pump is on.

2.61

ELECTRIC FILL PUMP

Tigercat 726E Feller Buncher

Controls and Operation AIR FILTER RESTRICTION INDICATOR

AIR CLEANER

ELECTRICAL RESTRICTION INDICATOR SWITCH

MECHANICAL AIR FILTER RESTRICTION INDICATOR

M726E-075

M726E-074

A filter restriction switch is installed on the outlet side of the air cleaner, the switch is used to signal the MD3 computer when the filter is restricted.

SAFETY ELEMENT

Engine Air Intake Filter Restricted. Service Machine to correct.

An alert warning message will appear on the MD3 display to indicate the engine air intake filter is restricted. Replace the primary air filter element if the alert message is displayed. Replace the secondary (safety) filter every third primary filter change to guarantee maximum performance and reliability.

PRIMARY ELEMENT 470-04

AIR FILTER ELEMENTS

The air cleaner on this machine uses two filter elements; a primary element and a safety element. It is accessible through the hydraulic compartment access door on the rear of the machine.

A mechanical filter restriction indicator is also connected to the outlet side of the air filter.

Replace the primary air filter when the indicator shows RED. This indicator provides a continuous reading whether the engine is running or is shut down. After replacing the filter, reset the indicator by pressing the reset button.

To ensure maximum engine protection, it is important that the elements be serviced correctly and at proper servicing intervals.

NOTE: Replace the safety element every third primary filter change.

2.62

Tigercat 726E Feller Buncher

Controls and Operation HOW IT WORKS

ENGINE AIR PRECLEANER ENGINE AIR PRECLEANER

3

3 4

2 1 5

480-017

1. Dirty air (1) enters the Precleaner, which is clamped onto the engine air intake.

2. Specially-designed vanes (2) , curved and angled to precisely direct air flow, move the dirty air toward the stainless steel impeller (3).

3. The dynamically balanced, one piece impeller (3) (only moving part) creates a tornado inside the housing.

4. The centrifugal force of the tornado expels the heavier than air dirt particles (4), chaff, dust, snow, rain, etc., out the discharge louver 5. Cleaned air (5) enters the engine air cleaner intake pipe, and the filter element has only the very light particles to remove.

RESULTS • Cleaner Air for The Engine!

• Longer Filter Element Life!

• Increased Engine Life!

• Increased Engine Performance!

• Reduced Operating Costs!

M726E-073

The engine air precleaner cleans engine air before it reaches the air cleaner filter elements.

It removes contaminants such as dust, powder, insects, rain and snow. This precleaner is self powered and self cleaning requiring virtually no maintenance. However, it should be checked periodically to make sure that foreign materials have not plugged the intake area or the exhaust port area.

NOTE: The precleaner compartment should be checked and cleaned out daily to ensure proper operation of the precleaner.

NOTE: Periodically remove the precleaner assembly and check the spinner assembly for wear or dirt build-up on the blades. Clean the spinner assembly or replace it if the blades are worn.

2.63

Tigercat 726E Feller Buncher

Controls and Operation

AIR CLEANER UNLOADER VALVE

UNLOADER VALVE

M726E-076

This rubber valve on the tube of the air cleaner housing should be checked before every shift (8 hours). If this valve is missing, damaged or has turned hard, it will cause the air cleaner to become ineffective. The valve should suck closed at 1/3 throttle.

This valve should be replaced every 1000 hours.

Remove the unloader valve from the tube of the air cleaner housing. Check and clean the valve.

A good valve is soft and flexible. If plugged, be sure to check the filter elements as they may need replacing as well. Reattach the valve to the tube.

When operating in high dust conditions, the unloader valve should be checked and squeezed every 2 hours to release dust buildup.

In addition refer to the LUBRICATION AND MAINTENANCE SCHEDULE in AIR CLEANER MAINTENANCE in SECTION 3 of THIS MANUAL.

2.64

Tigercat 726E Feller Buncher CLEANING A/C CONDENSER, OIL COOLER, RADIATOR AND CHARGE AIR COOLER (COOLER PACKAGE) 1

M726E-064

Controls and Operation

2

M726E-078 RIGHT SIDE - CROSS-FLOW FAN The cross-flow fan is mounted on the right side of the machine. The cross-flow fan draws air from the left side of the machine through the door and cooler package blowing it out of the right side of the machine.

The cooler package should be manually checked every 8 hours (every shift) or more often where conditions cause accumulation of twigs, leaves, pine needles and dust. All of the engine enclosure doors should also be checked.

LEFT SIDE - COOLER PACKAGE ACCESS DOOR AND PANEL

CHARGE AIR COOLER

RADIATOR

A/C CONDENSER CORE

PROCEDURE: 1. Shut down as per instructions in ENGINE STOPPING in this SECTION.

HYDRAULIC OIL COOLER

Always follow proper engine shutdown procedures. The important benefits are: •

Extended life of engine, cooling and exhaust systems.

COOLER PACKAGE

•

Reduced risk of post shutdown fires.

The cooler package is located on the left side of the machine and consists of the charge air cooler, radiator, A/C condenser and hydraulic oil cooler.

•

Interior of machine cools significantly reducing risks from touching hot surfaces.

M726E-077

2. Open both cooler package access doors on the sides of the machine by swinging the latch pin stop to the side, lifting up the pin and swing.

3. Lift out the bottom screen panels on the right and left sides of the front engine area, behind the cab.

2.65

Tigercat 726E Feller Buncher

Controls and Operation

Compressed air or water may be used for cleaning.

USING THE FAN SWITCH IN THE EVENT OF AN ENGINE COOLING AND/OR HYDRAULIC OIL TEMPERATURE ALARM.

CAUTION • If using compressed air for cleaning, use at 2.1 Bar (30 psi) or less.

• Always use personal protective equipment to guard against flying debris.

FAN SWITCH

If an oil leak occurs in this area it should be thoroughly power-washed with a mild soap to ensure that all of the oil is removed. The presence of oil causes dust and dirt to cling to surfaces which will impair the reversible fan's ability to remove dust and dirt particles.

M726E-044

CONTROL PANEL

In the event of an engine cooling temperature and/or hydraulic oil temperature alarm:

Care must be taken when cleaning this assembly, as the components can be damaged by careless handling and cleaning.

1. Stop working the machine, keep engine at high idle.

USING THE FAN CLEAN FUNCTION TO REMOVE DEBRIS DURING OPERATION

FULL ON

The hydraulic fan circuit has a CLEAN function for use in cleaning debris from the charge air cooler, radiator, oil cooler, A/C condenser and air intake door screens during operation. By “reversing” the direction of the fan, air flows in the opposite direction, thereby forcing dust and debris off the charge air cooler, radiator, oil cooler, A/C condenser and air intake door screens. Ensure that there are no personnel standing directly to the left of the machine when performing this operation, as dust and debris will fly out. Refer to FAN-SWITCH in THIS SECTION for more information.

AUTO CLEAN M726E-131

2. Press and hold the top of the fan control switch in the FULL ON position until cooling is achieved.

3. If necessary press and hold the bottom of the switch for 10 seconds to use the CLEAN function to reverse fan flow and clean debris from the cooler package and air intake door screens.

4. In severe operating conditions manual cleaning of debris may be required.

5. If the problem persists check engine coolant and/or hydraulic oil levels. Refer to OPERATING MACHINE ~ PRESTART CHECKS in THIS SECTION. 6. Release the switch to return it to AUTO mode and check for proper operation of the fan.

In the event of a problem with the automatic control system the fan control switch should be placed in the FULL ON position while the machine is operating until the fan control can be properly repaired.

NOTE: AUTO REVERSE is disabled when fan is set to 'FULL ON".

2.66

Tigercat 726E Feller Buncher OPERATING MACHINE

Controls and Operation

Before operating the machine, follow the PERIODIC MAINTENANCE instructions in SECTION 3 of THIS MANUAL. Also, refer to the Engine Operator's Manual supplied with this machine.

HYDRAULIC OIL RESERVOIR

SIGHT GAUGE, HYDRAULIC OIL LEVEL

PRE-START CHECKS: 1. Unlock cab doors, engine enclosure doors and hydraulic compartment doors.

2. Ensure ignition switch and cutter switch are in the OFF position.

SENDING UNIT, HYDRAULIC OIL TEMPERATURE

PARKING BRAKE SWITCH

HYDRAULIC OIL RESERVOIR

726E-079

5. Visually check hydraulic oil level sight gauge.

The level should be between the HIGH and LOW marks on the level gauge.

M726E-044

CONTROL PANEL DIPSTICK

3. Check parking brake for proper operation and and set parking brake ON (ENGAGED).

Fuel DEF M726E-085

6. Check the engine oil level. The level of the oil must be between the ADD and FULL marks on the dipstick.

726E-052

4. Turn Ignition switch on to check fuel and DEF levels on MD3 display and if required fill with the appropriate fluids.

DIPSTICK

M726E-083

PUMP DRIVE GEARBOX DIPSTICK

7. Check pump drive gearbox oil level. Dipstick is located near the right rear of engine.

2.67

Tigercat 726E Feller Buncher

Controls and Operation ENGINE AIR PRECLEANER

M726E-130

CHECK ENGINE COOLANT LEVEL

M726E-073

8. Check the engine coolant level.

11. Check air intake precleaner for foreign material build-up in air intake area or exhaust port area.

WARNING

CHARGE AIR COOLER

RADIATOR

Shut off engine. Only remove filler cap when cool enough to touch with bare hands. Slowly loosen cap to first stop to relieve pressure before removing completely.

A/C CONDENSER CORE HYDRAULIC OIL COOLER

M726E-077

COOLER PACKAGE

12. Clean cooler package. Refer to CLEANING A/C CONDENSER, OIL COOLER, RADIATOR AND CHARGE AIR COOLER in THIS SECTION. DRAIN PLUG

UNLOADER VALVE

726E-078

9. Drain water from fuel filter/water separator.

DIPSTICK

M726E-076

13. Check air cleaner unloader valve.

726E-069

10. Check transmission oil level (dipstick).

2.68

Tigercat 726E Feller Buncher

Controls and Operation

AIR CHARGE VALVE

PRESSURE GAUGE

196-9A

PRESSURIZED WATER SYSTEM

14. Check pressurized water tank pressure gauge, located on the left side of the seat base.

15. Be sure that all covers, guards and doors are securely fastened.

16 Check all of the fasteners retaining the disc saw teeth and tighten them to the proper torque level.

17. Replace all worn disc saw teeth or rotate worn teeth to align fresh cutting tips.

18. Replace the tooth fastener whenever replacing a saw tooth.

19. Inspect the cutting disc for stress cracks.

20. Check that the cutting disc does not wobble due to worn saw shaft bearings.

21. Never start or use a machine if the disc saw has missing teeth, missing teeth fasteners or a bent disc.

22. Shut down the machine immediately if you feel a vibration when the cutting disc is running.

23. Check that the saw housing is clear of debris and obstructions and undamaged.

2.69

Tigercat 726E Feller Buncher STARTING ENGINE: 1. Ensure that PRE START CHECKS have been performed and that the area is clear of personnel prior to starting the engine.

2. Sound horn to warn personnel of machine start-up.

NOTE: The engine will not turn over unless the parking brake is ENGAGED. 3. ENGAGE parking brake.

4. Turn key switch to RUN position and observe computer display. WAIT for the screen to display the gauges before starting the engine.

Controls and Operation NOTE: If the engine does not start after three attempts, check the fuel supply system. Absence of blue or white exhaust smoke during cranking indicates no fuel is being delivered.

IMPORTANT: • After engine has started, keep engine speed low until engine oil pressure registers on the computer display. If it does not register within 10 seconds, stop engine and investigate cause.

•

Allow a cold engine to warm up at LOW IDLE for at least five minutes before applying any load. Check all engine parameters on the MD3 display often during the warm up period.

CAUTION Do not start engine by shorting across starter terminals. Start engine only from operator's seat.

If engine stalls while operating the machine, turn the key to the OFF position and repeat steps (1) through (6).

726E-052

5. Turn key switch to START position to crank engine. When engine starts, release key to RUN position.

726E-054

6. Observe the MD3 display to ensure the engine oil pressure rises above 10 psi.

2.70

Tigercat 726E Feller Buncher

Controls and Operation

RESTARTING AN ENGINE THAT HAS RUN OUT OF FUEL If the engine runs out of fuel, perform the following:

HAND PRIMER

VENT PLUG

1. Refill fuel tank completely.

2. Turn the key switch to the RUN position to turn on the fuel shut off solenoid. Loosen the vent plug on the fuel filter/water separator head. Use primer pump to refill filter until fuel free of air flows from vent on top of filter head, then tighten vent plug. Turn key switch off and repeat. As well, bleed the system according to engine manual procedures.

WARNING DO NOT USE ETHER! Engine is equipped with an electric heater starting aid. Use of ether may cause an explosion and severe injury.

3. Crank engine until it starts. If it fails to start after 20 seconds, stop and wait for 2 minutes before trying again.

726E-078

NOTE: Do not use ether to restart an engine that has run out of fuel.

IMPORTANT: To prevent damage to starter, do not engage starter motor for more than 15 to 20 seconds.

Wait 2 minutes between each attempt to start the engine. If engine fails to start, refer to engine manufacturer OPERATOR'S MANUAL.

2.71

FUEL FILTER / WATER SEPARATOR

Tigercat 726E Feller Buncher

Controls and Operation

COLD WEATHER STARTING

NOTICE

IMPORTANT! Cold start-ups can result in pump failure, refer to "HYDRAULIC OIL CHART" for recommended oil viscosity and temperature ranges.

Cold temperatures may require the use of an engine block heater, engine oil pan heater, hydraulic oil heater and fuel heater.

The engine is equipped with an air intake heater with a grid element.

WARNING: Using starting fluid (or ether start aids) on an engine equipped with a grid heater element can cause an explosion. NEVER USE STARTING FLUIDS on an engine equipped with a grid heater element.

• DO NOT IDLE THIS ENGINE FOR MORE THAN 4 HOURS. • DAMAGE TO EMISSION CONTROL SYSTEM WILL RESULT.

WARNING • EXPLOSION HAZARD. • DO NOT USE ETHER.

59912BENG R0

• ENGINE EQUIPPED WITH HEATER STARTING AID.

IMPORTANT !

• USE OF ETHER COULD RESULT IN DEATH OR SERIOUS INJURY.

Engine should not idle longer than 4 consecutive hours. Damage to the emission control system will result. When this machine idles for an extended period excess hydrocarbon buildup is created in the SCR after treatment system. Burn off of excess hydrocarbon at full load immediately after a long idle period will generate excess heat which will cause damage to emission control system components. It will take 45 minutes at 40% load (or an SCR exhaust outlet temperature of 320°C (608°F)) to burn off the hydrocarbon that accumulates during a 4 hour long idle.

36782BENG R0

Preheating of hydraulic oil is recommended as standard procedure in cold weather.

1.

Follow the STARTING ENGINE - SEE ENGINE MANUAL instructions for COLD WEATHER STARTING procedure.

IMPORTANT! To prevent damage to starter, do not engage starter motor for more than 15 to 20 seconds.

Wait 2 minutes between each attempt to start the engine. If engine fails to start, refer to engine manufacturer operator's manual.

2.

During the engine warm-up period constantly monitor engine coolant temperature and engine oil pressure. Stop engine if any pressure or temperature does not meet the specification.

3.

Continue with MACHINE PREPARATION procedure when the engine coolant temperature registers NORMAL.

2.72

Tigercat 726E Feller Buncher

Controls and Operation

MACHINE PREPARATION

(m) Set engine speed to LOW IDLE.

SYSTEM TEST AND WARM-UP

WARNING

Before commencing operations, proceed with steps (a) through (n) to accomplish:

Ensure that the saw blade has stopped rotating before leaving the cab.

• Warm up the hydraulic system.

• Test all systems for proper operation.

(n) Leave the cab and visually check hose connections and cylinders for leaks. Check under the machine for oil leaks.

• Inspect for hydraulic oil leaks.

CAUTION

WARNING

If any system fails to respond to the controls, stop the warm-up procedure and call a mechanic, otherwise serious damage to pumps and other components could result.

Assuming machine was parked on level ground at last shutdown:

Never use your bare hand to check for fluid leaks.

Fluid leaks under pressure may not be visible. When searching for leaks, wear work gloves and use a wrench or piece of wood to move hydraulic hoses. Do not grab hold of hydraulic hoses. Wear safety goggles for eye protection.

(a) Start engine. (b) Ensure computer display is indicating normal operating conditions. (c) Check that all personnel are clear of the machine. (d) Set engine speed to 1100 rpm. (e) Slowly raise and lower boom, check for proper operation.

With the attachment raised slightly off the ground: (f) Operate the accumulator and clamp arms and check for proper operation. (g) Tilt the attachment forward and back and check that it is operating correctly. (h) Steer the machine to the left and right. (i) When cold weather conditions exist, continue the process of warming up the hydraulic system by repeating steps (e) through (h) several times. As the hydraulic system warms up, engine speed can be increased gradually to the HIGH IDLE position. (j) Turn attachment on. (k) After completion of the warm-up and system testing, turn the attachment OFF, stop the blade and rest the attachment on the ground. (l) Set the parking brake ON.

2.73

Tigercat 726E Feller Buncher

Controls and Operation

STOPPING ENGINE

CARE OF THE MACHINE

IMPORTANT: Stopping the engine immediately after it has been working under load can result in overheating and premature wear of the engine components. Follow the stopping procedure outlined below to allow the engine to cool.

2. Apply grease to all lubrication points at required intervals.

1. Ensure that all fluid levels are always at the proper level. Use the preventative maintenance schedule in SECTION 3 of this manual .

1. Park machine on level ground and rest attachment on the ground.

3. Do not apply load to a cold engine.

4. Close and secure all doors and access covers.

2. Reduce engine speed to LOW IDLE and let run for approximately three minutes to allow gradual dissipation of heat and also to reduce turbocharger speed. This will also prevent loss of coolant by after boil and possible hot spot damage to the engine.

5. Do not allow branches, twigs, leaves or pine needles to build up around radiator intake doors or anywhere else on the machine.

Clean frequently.

6. Be sure that the attachment is resting on the ground before servicing or parking the machine.

3. Do not race engine before shut-off.

4. Engage parking brake.

5. Stop engine by turning key switch to the OFF position.

Note that whenever the engine is stopped all DEF solution is pumped back to tank before the engine power system is turned off. This process takes approximately 90 seconds. Refer to SELECTIVE CATALYTIC REDUCTION SYSTEM in SECTION 3 for more information.

7. Follow proper procedure for cleaning windows described in this section.

Note also that this machine is equipped with an After Run/ Accessory Relay which delays by 90 seconds the power disconnect to engine related fuses and relays (ECU /ATS relay, NOx Sensor relay, NOx Sensor fuse, ECU Power fuse, DCU fuse).

WARNING • Before leaving the machine, park it in a safe position on level ground.

• Engage parking brake, lower the attachment to the ground.

• Never work behind, in front of, or below a machine that has been parked on a grade.

• Take additional precautions by placing the wheels against a rock, tree or other secure object.

IMPORTANT: Only use the master disconnect to shut off a running machine in an emergency. A fault code will be logged by the ECM on the engine for improper shut down and power down.

2.74

Tigercat 726E Feller Buncher

Controls and Operation

CARE OF POLYCARBONATE WINDOWS IN CAB

•

(Windshield, skylight and three rear windows) Most windows used in the cab are made from a polycarbonate resin thermoplastic. This material is a replacement for glass when improved strength, durability and safety is required.

Polycarbonate material is expected to resist heavy impact from large branches and falling tree tops and to absorb high levels of energy when contacted by high velocity thrown objects such as wood chips, disc saw blade teeth or broken harvester head saw chain.

The extreme operating environment seen in logging applications heightens the need to regularly inspect and properly maintain polycarbonate cab windows.

Polycarbonate windows are an essential piece of operator protective equipment and should be maintained as such. It is important to note that cracks, chips, notches or scarring anywhere on the viewing surface or edges of the window will decrease ability to resist heavy impacts and therefore compromise effectiveness as operator safety protective equipment. Windows with these defects must be replaced immediately.

Refer to the next section for detailed information regarding inspection and maintenance of polycarbonate windows.

• • •

•

Cracks, chips, notches or scarring anywhere on the viewing surface of the window will decrease ability to resist heavy impacts.

Windows with these defects must be replaced immediately.

Bent, dented or missing window retaining parts must be replaced immediately.

Rubber materials used in mounting the window must be maintained in good condition.

Identification of the polycarbonate originally used by Tigercat is hot stamped in a corner of the window to identify its composition. Do not use any replacement window without proof of its material composition. Do not substitute with any other materials.

Skylights, cab structures, windows and window retaining parts must not be modified or replaced with components that are not approved by Tigercat.

RESISTANCE TO CHEMICALS The resistance of polycarbonate material to chemical exposure varies widely. Fortunately, polycarbonate materials have good resistance to diesel fuel, grease, hydraulic oil, kerosene and engine oil.

Other chemicals however can seriously weaken the polycarbonate.

DO NOT permit any of the following chemicals to come into contact with polycarbonate windows: • acetone • air conditioning refrigerant • ammonia • anti-freeze • benzene • brake fluid • carbon tetrachloride • cutting oils • gasoline • lacquer thinner • toluene • turpentine • xylene RESISTANCE TO WATER Polycarbonate material has good resistance to water up to approximately 65°C (150°F). Above this temperature the effect of water is timetemperature related. This means that the higher the water temperature, the shorter the time before the polycarbonate is adversely affected.

INSPECTION AND MAINTENANCE Daily inspection and maintenance is essential to confirm that the window’s ability to protect the operator has not been compromised.

• Inspect all windows daily and immediately after any impacts.

• Check for any damage to the window material or steel structure in the area of the window mounting.

• The edges of the polycarbonate window must be evenly and fully supported on a flat surface around the entire window opening at all times.

Bent or dented skylight structures must be replaced immediately. Bent or dented cab structures must be evaluated immediately for possible repair or replacement.

• The edges of the polycarbonate window must be free from cracks, chips, notches or scarring and must not be pinched or stressed.

These defects will decrease ability to resist heavy impacts. Windows with these defects must be replaced immediately.

2.75

Tigercat 726E Feller Buncher

Controls and Operation

Exposing polycarbonate to repeated steam cleanings or high temperature pressure washing may result in crazing, a phenomenon that causes clouding of the surface. Crazing can ultimately result in a loss of physical strength and may precede a fracture.

CLEANING INSTRUCTIONS The viewing surfaces of polycarbonate cab windows are specially treated with a hard coating to provide enhanced resistance to abrasion and ultra-violet (UV) radiation.

The following instructions are provided to prolong the life of this protective hard coating.

•

DO NOT use brushes, razor blades, scrapers, squeegees or other sharp tools on polycarbonate windows.

•

DO NOT clean polycarbonate windows when the daytime temperature is high or in direct sunlight.

•

DO NOT use abrasive or highly alkaline cleaners on polycarbonate windows.

•

DO NOT use glass cleaners in either aerosol or non-aerosol containers to clean polycarbonate windows.

•

Failure to follow these cleaning instructions will shorten the service life of polycarbonate and may cause visual hazing, loss of light transmission and delamination of the polycarbonate hard surface coating.

1. Rinse the window thoroughly with lukewarm water 2. Using a soft cloth, cellulose sponge or chamois, gently wash the window with a mild solution of soap or detergent in lukewarm water. Do not scrub or use brushes or squeegees.

CONCEALING HAIRLINE SCRATCHES The appearance of scratches and minor abrasions on the surfaces of polycarbonate windows can be minimized by using a mild automotive polish such as:

Brand name soaps and detergents recommended for cleaning polycarbonate are: • Fantastik • Formula 409 • Hexcel F.O. 554 • Joy • Lysol • Mr. Clean • Neleco-Placer • Pine-Sol • Top Job

• • •

Be certain to clean the polycarbonate window as outlined prior to application of an automotive polish. Refer to CLEANING INSTRUCTIONS. GRAFFITI REMOVAL •

For removal of paints, marking pen inks, etc., the use of Butyl Cellosolve is generally effective. The use of masking tape, adhesive tape or lint removal tools works well for lifting off old weathered paints.

•

To remove labels, stickers, etc., the use of kerosene, VM&P Naphtha, or petroleum spirits is generally effective. When the solvent will not penetrate sticker material, apply heat (hair dryer) to soften the adhesive and promote removal.

3. Rinse the window thoroughly with lukewarm water.

4. Dry the window with a moist soft cloth, cellulose sponge or chamois to prevent water spotting.

5. To remove grease or oil, first rub lightly with a good grade of VM&P Naphtha or isopropyl alcohol followed by the same rinse, wash, rinse and dry procedure described in steps 1 to 4.

Refer also to RESISTANCE TO CHEMICALS for a list of chemicals which should not be permitted to come into contact with polycarbonate windows.

Refer also to RESISTANCE TO CHEMICALS for a list of chemicals which should not be permitted to come into contact with polycarbonate windows.

FIRE PRECAUTIONS

CAUTIONS •

Johnson’s Paste Wax Novus Plastic Polish #1 and #2 Mirror Glaze Plastic Polish

Polycarbonate window material will ignite when exposed to an ignition source in excess of 427°C (800°F). When working around polycarbonate windows, observe similar fire precautions to those in place for wood.

DO NOT use abusive cleaning procedures either by hand or pressure washing on polycarbonate windows.

2.76

Tigercat 726E Feller Buncher

Controls and Operation TOWING INSTRUCTIONS

CLEANING INSTRUCTIONS FOR GLASS WINDOWS (BOTH DOORS) Normal window cleaning procedures are acceptable.

A malfunction of the machine's equipment may make towing necessary.

Towing is only recommended over short distances. It is always better to make repairs at the point where the machine is parked whenever possible.

WINDOW SCREEN HANDKNOB

173-25

IMPORTANT! Before towing, the transmission must always be placed in NEUTRAL. Never tow a machine in gear. The extremely high forces created will cause significant damage to the components of the hydrostatic drive system and the transmission.

SIDE WINDOW SCREEN

SIDE WINDOW SCREENS The side window screens can be opened to clean the windows. Screens are provided for the personal protection of the operator. A handknob is provided on both the inside and the outside. By unscrewing either (not both) of these knobs, the screen will be free to swing out on the hinges. Be aware that the screen will swing outwards with considerable force, if the door is open.

Never tow the machine at over 2 mph. This will cause significant damage to the transmission.

Never press the forward or reverse pedals while the transmission is in neutral. This will cause significant damage to the transmission.

432-1

720D-024

TRANSMISSION SHOWN ENGAGED

1. To facilitate towing, the transmission must be placed in NEUTRAL, this will disconnect the wheels from the hydraulic motor.

HINGED SIDE WINDOW SCREENS

All handles should be hand tight only at all times.

Place a short bar through the hole in the lever and pull upwards to put the transmission into NEUTRAL as shown below.

432-3

2.77

TRANSMISSION SHOWN IN NEUTRAL

Tigercat 726E Feller Buncher

Controls and Operation 5. This machine is equipped with a hydraulic deactivated parking brake and it will be necessary to provide portable hydraulic pressure (250 psi) at the parking brake supply (C6) on the pilot manifold.

LIFT BOOM

CYLINDER

C6

'T' HANDLE

726E-073

718D-046

LIFT BOOM CYLINDER LOCK IN LOCK POSITION

Block the wheels. Remove parking brake supply hose from pilot manifold (C6) and connect to a remote power source. Plug port on pilot manifold. Pressurize circuit to 250 psi to disengage parking brake.

2. Raise the felling attachment off the ground and install the boom cylinder lift lock. Turn off the engine.

FRONT CHASSIS

REAR CHASSIS

6. Remove articulation lock bar.

RETAINING PIN

7. The machine will be towed from the rear, making use of the towing lug at rear of machine underneath the bumper.

LYNCH PIN

726D-039

Ensure a vehicle of equal power and size is used for towing.

LOCK BAR

When going downhill, be sure to use a holdback vehicle as the machine is now without any effective braking.

LOCK BAR IN LOCKED POSITION

8. When towing is completed, install the articulation lock bar and reconnect the steering cylinder hoses to their proper locations.

3. Install articulation lock bar. See instructions later in THIS SECTION. STEERING CYLINDERS

SM47

PILOT MANIFOLD

NORMAL HOSE CONNECTIONS

STEERING CYLINDERS

HOSES ON ONE CYLINDER CROSS CONNECTED FOR TOWING

4. To allow the machine to steer while towing and prevent damage to the steering cylinders, cross hydraulic hoses on one of the steering cylinders. This will allow trapped oil to flow freely between the two steering cylinders, providing ease of turning with some dampening effect.

2.78

Tigercat 726E Feller Buncher TRANSPORTING INSTRUCTIONS

Controls and Operation

IMPORTANT: When transporting the machine, Chains must be used to prevent forward, reverse and side to side movement of the machine.

The machine may be transported with the wheels on or off. If the wheels are removed the machine must be blocked so that the center joint is one inch or more above the truck bed.

With the wheels on or off:•

The attachment must be lowered to the truck bed.

•

The articulation lock bar must be installed.

•

The machine must be crossed chained (side to side) over and around both the front and rear axles.

IMPORTANT: Do not secure the machine to the truck ANYWHERE near the center joint area as this can seriously damage the center joint.

Use only transport regulation chains for this purpose, example; 5/16" grade 7 with a tensile strength of 43636 Kg/chain (96,000lbs/chain).

Using inferior or damaged chains could cause the load to shift.

The chains must be looped around the axles and hooked back onto the links of the chain creating a full loop around the axles. The chains should be attached to the opposite sides of the trailer and evenly tensioned with the load binders.

A

F B I

H G J E C

D G,H

I,J

A B C D E F G H I J 49360BUNI R1

E,F

2.79

Tigercat 726E Feller Buncher ARTICULATION LOCK BAR

Controls and Operation

1. Position machine on level ground and steer machine into a straight ahead position.

2. Lower attachment to the ground, apply parking brake, stop engine and remove key.

WARNING To prevent movement of machine and possible injury, install articulation lock bar before performing any work in the center joint area.

3. Remove both retaining pins from the front and rear chassis and slide lock bar out of front chassis and into tube socket on rear chassis.

Line up holes at each end of lock bar with holes in chassis' and secure in place with both retaining pins. Install lynch pins.

FRONT CHASSIS

REAR CHASSIS

RETAINING PIN

LYNCH PIN

726D-039

LOCK BAR

LOCK BAR IN LOCKED POSITION

4. After work is completed, slide lock bar into front chassis storage position and hold in place with retaining pin. Store second retaining pin in rear chassis tube socket.

Install lynch pins.

2.80

Tigercat 726E Feller Buncher LIFT BOOM CYLINDER LOCK

Controls and Operation LIFT BOOM

Before performing work under the attachment or lift boom, ensure that the attachment is firmly supported on level ground, on solid stands or, install lift boom cylinder lock.

CYLINDER

'T' HANDLE

726E-073

LIFT BOOM CYLINDER LOCK IN LOCK POSITION

Completely raise lift boom and place lock over one of the two cylinder rods with the open side facing down and wide end against the cylinder gland. Install 'T' handle retaining bolt through center hole.

Do not place yourself under the boom or attachment, while doing this. Do not damage the piston rod when installing the boom lift lock. Turn off the engine, turn key back to RUN position, press the INTERLOCK RESET switch to activate the pilot oil system.

SLOWLY lower the boom until the boom lift lock is securely in place.

CYLINDER LOCK

INTERLOCK RESET SWITCH

726E-079

CYLINDER LOCK STORAGE

The lift boom cylinder lock is stored on the inside of the hydraulic pump compartment door.

WARNING

M726E-044

Always install lift boom lock before working on or around machine with boom raised.

• Always install 'T' handle retainer bolt • Use only to support boom and attachment.

CONTROL PANEL

To remove the boom lift lock, start the engine, press INTERLOCK RESET switch and raise the boom completely. Without placing yourself under the boom or attachment, remove the 'T' handle retainer bolt, remove the boom lift lock and reinstall it on the inside of the hydraulic compartment door.

2.81

Tigercat 726E Feller Buncher

Controls and Operation

2.82

Tigercat 726E Feller Buncher SECTION 3 - LUBRICATION & MAINTENANCE FEBRUARY, 2014

CONTENTS - SECTION 3 A

AFTER TREATMENT SYSTEM............................................................................................................... 3.29 APPROVED ANTISIEZE PASTES........................................................................................................ 3.35 CATALYTIC CONVERTER................................................................................................................... 3.33 DENOX DOSING CONTROL UNIT (DCU)........................................................................................... 3.32 DIESEL EXHAUST FLUID (DEF) TANK............................................................................................... 3.31 DOSING MODULE (DEF INJECTOR).................................................................................................. 3.33 EXHAUST TEMPERATURE SENSORS.............................................................................................. 3.34 HEATER VALVE / HEATED DEF SUPPLY LINES................................................................................ 3.32 HUMIDITY SENSOR............................................................................................................................ 3.34 MIXER TUBE........................................................................................................................................3.33 NOX SENSOR...................................................................................................................................... 3.34 SUPPLY MODULE................................................................................................................................ 3.33 AIR CLEANER MAINTENANCE.............................................................................................................. 3.25 AIR CLEANER UNLOADER VALVE........................................................................................................ 3.27 AIR CONDITIONING SYSTEM, CHECKING........................................................................................... 3.38 AIR FILTER ELEMENTS................................................................................................................ 3.25, 3.28 AIR INTAKE SYSTEM, ENGINE AIR CLEANER FILTER ELEMENTS.......................................................................................................................... 3.28 IMPORTANT STEPS TO FOLLOW WHEN CHANGING FILTER ELEMENTS................................ 3.28 FILTER RESTRICTION INDICATOR.................................................................................................... 3.25 INTAKE TUBING AND JOINTS............................................................................................................ 3.28 B

BELT, ENGINE SERPENTINE, REPLACING........................................................................................... 3.43 BRAKE, PARKING................................................................................................................................... 3.43 C

CENTER JOINT LUBRICATION...................................................................................................................................... 3.39 MAINTENANCE.................................................................................................................................... 3.39 CONVERSIONS, COMMON.................................................................................................................... 3.55 D

DEF (DIESEL EXHAUST FLUID) DRAINING THE TANK.......................................................................................................................... 3.20 HANDLING AND STORAGE................................................................................................................ 3.35 TANK.....................................................................................................................................................3.31 DENOX 2 SYSTEM.................................................................................................................................. 3.29 DIESEL EXHAUST FLUID (DEF) HANDLING......................................................................................... 3.35 DRAINING THE DIESEL EXHAUST FLUID TANK.................................................................................. 3.20 DRIVE SHAFT SPLINE LUBRICATION, MIDDLE AND REAR................................................................ 3.44 E

EMERGENCY EXITS, CHECK DAILY....................................................................................................... 3.7 F

FILTERS DEF SUPPLY MODULE FILTER.......................................................................................................... 3.19 ENGINE AIR......................................................................................................................................... 3.25 ENGINE OIL......................................................................................................................................... 3.16 FUEL.....................................................................................................................................................3.16 FUEL/WATER SEPARATOR................................................................................................................. 3.16 HYDRAULIC OIL RETURN FILTERS................................................................................................... 3.21 HYDRAULIC OIL RETURN STRAINERS............................................................................................. 3.23 HYDROSTATIC CHARGE PUMP PRESSURE FILTERS.................................................................... 3.24 SERVICING GUIDELINES FOR OIL FILTERS........................................................................... 3.21, 3.24 FIRE PREVENTION................................................................................................................................... 3.8

Tigercat 726E Feller Buncher

Lubrication and Maintenance

H

HYDRAULIC OIL RETURN STRAINERS................................................................................................ 3.23 HYDRAULIC OILS................................................................................................................................... 3.13 N

NEW MACHINE MAINTENANCE FIRST 125 HOUR INSPECTION AND SERVICE REPORT................................................................... 3.3 INITIAL PRE-DELIVERY INSPECTION.................................................................................................. 3.3 TIGHTENING POINTS........................................................................................................................... 3.3 O

OIL LOST FROM LEAKAGE...................................................................................................................... 3.3 OIL SAMPLE COLLECTION PROCEDURES............................................................................................ 3.5 OIL SAMPLING PROGRAM............................................................................................................... 3.4, 3.5 P

PARKING BRAKE.................................................................................................................................... 3.43 PRESSURE SETTINGS........................................................................................................................... 3.50 PRESSURIZED WATER SYSTEM MAINTENANCE............................................................................... 3.36 S

SCHEDULED MAINTENANCE GENERAL............................................................................................................................... 3.6, 3.7, 3.8 8 HOURS................................................................................................................................................3.9 48 HOURS..............................................................................................................................................3.9 125 HOURS.......................................................................................................................................... 3.10 500 HOURS.......................................................................................................................................... 3.10 1000 HOURS........................................................................................................................................ 3.11 2000 HOURS........................................................................................................................................ 3.11 SELECTIVE CATALYTIC REDUCTION (SCR) AFTER TREATMENT SYSTEM..................................... 3.29 SPEED CONTROL LEVER ADJUSTMENT............................................................................................. 3.46 STARTUP PROCEDURE AFTER MAINTENANCE................................................................................. 3.40 STRAINERS, HYDRAULIC OIL RETURN............................................................................................... 3.23 T

TORQUE CHART..................................................................................................................................... 3.48 TORQUE CHART, GENERAL.................................................................................................................. 3.49 TORQUE, FLUID CONNECTIONS...................................................................................... 3.51, 3.52, 3.53 TRANSMISSION...................................................................................................................................... 3.39 W

WEIGHTS OF COMMERCIAL WOOD..................................................................................................... 3.54 WHEELS, INSTALLING.............................................................................................................................. 3.3

3.2

Tigercat 726E Feller Buncher

Lubrication and Maintenance

PREVENTIVE MAINTENANCE SCHEDULE NEW MACHINE MAINTENANCE *INITIAL PRE-DELIVERY INSPECTION:PERFORM THE INITIAL PRE-DELIVERY INSPECTION USING Tigercat FORM NUMBERS 5340 AND 5347; "PDI AND 125 HOUR INSPECTION REPORT"

*FIRST 125 HOUR INSPECTION AND SERVICE REPORT:WITH THE OWNER'S MECHANIC PRESENT, PERFORM AN INSPECTION AND SERVICE ACCORDING TO THE Tigercat FORM NUMBERS 5340 AND 5347; "PDI AND 125 HOUR INSPECTION REPORT" THIS MUST BE COMPLETED WITHIN THE FIRST 125 HOUR TIME FRAME. *IMPORTANT: TO QUALIFY FOR CONTINUED WARRANTY, THIS REPORT MUST BE COMPLETED AND RETURNED TO Tigercat Industries Inc. WARRANTY DEPARTMENT.

Tightening points for First 125 hour inspection report:~ All hydraulic connections Hose clamps Center joint pin securing bolts Transmission securing bolts Engine mounting bolts Pump drive gearbox securing bolts Axle mounting bolts Wheel retaining bolts Cab securing bolts Pin retainers Any other loose nut, bolt or fitting

IMPORTANT! Wheels: When installing wheels, ensure that all paint has been removed from the mating surfaces of both the wheel disc and the flange of the axle to ensure metal to metal contact.

For additional instructions also refer to section 8 of the service manual.

Hour meter ~ maintenance: Check the engine hour meter on a regular basis to determine your scheduled maintenance times.

NOTE: Use of filters other than genuine Tigercat replacement filters is not recommended.

Refer to diesel engine service manual and attachment manual for additional required maintenance at this scheduled time period.

The intervals and times on the scheduled maintenance chart in this manual are for normal operating conditions.

If your machine is being operated in difficult or severe conditions, you should service your machine at shorter intervals.

*OIL LOST FROM LEAKAGE

PER LEAKAGE RATE DAY ONE DROP IN 10 SECONDS 0.424 ONE DROP IN 5 SECONDS 0.852 ONE DROP PER SECOND 4.26 THREE DROP PER SECOND 14.2 DROPS BREAK INTO STREAM 90.83

LOST 0IL (LITERS) LOST 0IL (GALLONS) PER PER PER PER PER MONTH YEAR DAY MONTH YEAR 12.72 152.0 0.112 3.36 40.0 25.6 306.6 0.225 6.75 81.0 127.76 1533.1 1.125 33.75 405.0 425.86 5110.31 3.75 112.5 1350.0 2725.5 32706.0 24.00 720.0 8640.0

3.3

Tigercat 726E Feller Buncher

Lubrication and Maintenance

TIGERCAT OIL SAMPLING PROGRAM Using the Tigercat Advanced Oil Analysis Program on a regular basis is an excellent preventative maintenance tool. Oil sampling cost is at the owner’s expense, however, studies have shown that it is possible to receive a 10 to 1 payback when looking at the amount saved on repair costs to the amount invested in a scheduled oil analysis program. Some of the benefits of a sampling program include: •

Detect problems early before they become major catastrophic failures.

•

Better ability to schedule downtime and forecast cost of repairs.

•

Monitor maintenance schedules and practices and confirm that the required maintenance is being done on time.

•

Increase used equipment value by providing proof of proper maintenance.

This Program uses the most modern technology available to analyze all oil samples. Most test results are available within 24 hours after receipt of the sample and are supplied in an easy to understand report, which calls for specific action and makes detailed recommendations. This report is available as a mailed or faxed hardcopy, sent via e-mail or can be viewed on the internet.

This program will provide Tigercat machine owners access to an Advanced Oil Analysis Program for all major machine components including powertrain components, specifically hydrostatic pump and motors, boom/steer pump, axles, transfer case, pump drive gearbox, etc.

700 Series

Location

First Sample

Follow-up Samples

Hydraulic Oil

125 hrs

Every 1000 hrs or 6 Months

Transmission

125 hrs

Every Oil Change (500 hours or 3 Months)

Pump Drive Gearbox

125 hrs

Every Oil Change (500 hours or 3 Months)

Front & Rear Axle

125 hrs

Every Oil Change (1000 hours)

Tigercat Oil Analysis Kits are available from your Tigercat dealer parts department. If required, arrangements can also be made with your Tigercat dealer to supply and perform all of the required followup oil samples.

Refer also to OIL SAMPLE COLLECTION PROCEDURES in THIS SECTION for sample valve and drain plug locations.

TIGERCAT OIL ANALYSIS KITS Each kit includes a Pre-paid Sample Bottle and Sample Information Form. Pre-printed mailing labels are also included to ensure all samples are quickly returned directly to the lab for immediate analysis and results within 24 hours of receipt.

The same type of sample bottle can be used for all types of oil testing including: Hydrostatic pump and motors, boom/steer pump, axles, transfer case, pump drive gearbox, etc.

To ensure accurate and meaningful results are obtained, each kit also includes detailed instructions on how to properly collect, prepare and ship the oil samples.

Contact your Tigercat Dealer Parts Department to order Kits.

3.4

Tigercat 726E Feller Buncher

Lubrication and Maintenance

TIGERCAT OIL SAMPLING PROGRAM OIL SAMPLE COLLECTION PROCEDURES

OIL SAMPLING CONNECTOR

Fill out the Sample Information Form (SIF) completely and accurately. When taking multiple oil samples, fill out all of the required SIF forms in their entirety, prior to taking any oil samples. Then, immediately package each completed SIF form together with the matching oil sample in the black outer shipping container as each individual sample is taken. This will reduce the possibility of mixing up or incorrectly identifying the SIF forms and oil samples. Incorrectly identified samples could result in a false warning alarm.

The accuracy of the lab analysis results is very dependent on the quality of the oil sample taken. Collection of clean oil samples that are representative of the main body of oil are essential if meaningful lab results are to be obtained.

Erroneous readings may result if proper collection, handling, packaging and shipping practices are not followed prior to the sample being tested by the lab. To be able to accurately compare and trend the lab results over time, all follow-up samples should be consistently taken from the same location using the same techniques as all previous samples.

•

Ensure that all sample valves and drain plugs are clean and free of debris.

•

Remove the sample bottle cap only when ready to take the sample. Keep the cap clean – do not put it in your pocket or let it get contaminated in any way.

•

Do not allow any airborne dirt, etc. to enter the sample bottle.

•

Avoid contamination of the sample – replace the sample bottle cap immediately after filling the bottle to approximately ¾ full. All samples taken should be immediately forwarded to the lab for processing.

Contact your Tigercat dealer to purchase additional or replacement hydraulic sample valves or drain plugs.

In cases where oil samples must be pumped or otherwise drawn out of a reservoir or housing, a hand operated oil suction pump is also available from your Tigercat dealer.

WATER ABSORBING ELEMENT (COLOR BLUE) M726E-110

HYDRAULIC OIL RETURN FILTERS

Hydraulic Oil Samples: • Hydraulic oil samples should be taken from the circulating oil flow at operating temperature, with no functions actuated, using sample valves that are permanently located on the machine whenever possible.

•

To obtain a representative oil sample, sample valves must be purged before the actual oil sample is taken. Drain a minimum of 3 or 4 ounces of oil into a separate container and discard this oil using approved recycling methods.

•

Replace the dust cover on the sample valve immediately after taking the oil sample and sealing the sample bottle.

Transmission, Axle and Pump Drive Gearbox Samples: •

These samples can be taken during the oil change process.

•

To obtain a representative oil sample, ensure the oil is warm and has not settled very long (within 30 minutes of shutdown).

•

Place the required drain container under the machine to capture the used oil to be discarded using approved recycling methods.

•

Remove the drain plug and allow approximately 50% of the oil to drain, then place the sample bottle in the stream of draining oil to obtain a representative sample.

3.5

Tigercat 726E Feller Buncher

Lubrication and Maintenance

GENERAL CAUTION All handles, steps and platforms must be kept free of grease, oil, fuel, mud, snow, ice and forest debris to prevent risk of personal injury. þ Clean around filler caps before checking or adding fluids. þ Clean around hydraulic fittings before breaking connection. Plug or cap immediately. þ Clean up spills as soon as possible. þ Always use clean hydraulic oil and filters. þ Drain dirty oil while still warm. þ Do not exceed recommended fluid levels. þ Service all hydraulic filters after the failure of a pump, motor, cylinder or valve. Failures of this nature could contaminate the entire hydraulic system. þ Top up diesel fuel at end of each shift to reduce contamination by condensation. þ Clean up oil spills on walking surfaces and top of engine enclosure immediately. þ Inspect the EXHAUST SYSTEM DAILY for any signs of LEAKAGE. Check for worn, cracked, broken, or damaged pipes or muffler.

Also check for missing or damaged bolts or clamps. Should any exhaust leaks or defective parts be found, repairs must be made immediately. Engine exhaust leaks can cause fires, DO NOT OPERATE the machine until the exhaust leak is repaired.

þ During daily operation of the machine, the occurrence of exhaust leaks are usually accompanied by a change or increase in engine exhaust noise levels. These audible warnings cannot be ignored. Should any exhaust leaks occur during operation, the machine must be shut down immediately and not put back to work until the necessary repairs have been completed. þ Before welding on machine be sure master switch is disconnected and disconnect multi pin connectors on engine CPU and engine wiring harness. þ When welding secure ground connection as close to working position as possible to prevent arcing across machined surfaces or through bearings. þ Clean away all branches, bark and chips.

Clean up all traces of oil to avoid fires. þ Always have a fire extinguisher at hand. þ For safety, always lower boom assembly to the ground when leaving cab, leaving machine unattended or during service. þ For safety, when working under boom, always lower to ground, support properly or install lift boom cylinder locking device . (Refer to section 2 of this manual) __________

3.6

Tigercat 726E Feller Buncher

Lubrication and Maintenance

GENERAL CHECK EMERGENCY EXITS, DAILY:~

A

M726E-019

M726E-016

SKYLIGHT OUTSIDE HANDLES

L.H. DOOR PRIMARY EXIT

Two alternate exit routes are provided:

A 726E-070

SKYLIGHT - INSIDE HANDLES

SKYLIGHT/EMERGENCY EXIT

M726E-017

R.H. DOOR ALTERNATE EXIT

The Skylight serves as a third exit from the cab should the two doors become blocked. There are two retaining handles (A) on the inside and two on the outside to allow removal of the hatch from either side.

• Right hand cab door.

SKYLIGHT

Turn the handles in the direction indicated on the label to remove the skylight. These handles should only be HAND TIGHTENED, to allow them to be unscrewed in case of an emergency.

M726E-017

SKYLIGHT ALTERNATE EXIT

The R.H. Cab Door and Skylight are only to be used if the left hand cab door cannot be opened.

It is therefore essential that these emergency exits be checked every day to ensure they are fully operational.

• Skylight/emergency exit.

3.7

Tigercat 726E Feller Buncher

Lubrication and Maintenance

GENERAL CHECK FIRE EXTINGUISHER, DAILY:~

FIRE PREVENTION Maintaining your machine properly will greatly extend its life and reduce your operating costs.

Fire can result in a machine loss which can be financially devastating.

CAUTION

CHECK CHARGE GAUGE DAILY

AFTER transporting (trucking) a machine from one job sight to the next, open all doors and access panels and blow off any debris that could have re-positioned itself onto the engine and exhaust parts due to wind turbulence caused by the journey.

1. Forest debris and fine organic material (twigs, pine needles, branches, bark, leaves, saw dust, small wood chips) and any other combustible materials when allowed to accumulate, form a fuel source that when ignited is extremely difficult to extinguish. A thorough program of regular cleaning and washing will reduce the possibility of a fire starting. In the event a fire does start, the regular cleaning program will improve the chances of successfully extinguishing a fire.

2. Pay close attention to wiring and plumbing routings during maintenance, ensure that ALL wiring harnesses or hydraulic hoses are properly restrained and clamped to prevent damage from chaffing.

3. If equipped, read the fire suppression system manual and have the system serviced regularly by qualified personnel.

4. In case of fire lower the boom system to the ground and shut off the engine before discharging the fire suppression system.

Also refer to FIRE PREVENTION in SECTION 1 of THIS MANUAL for additional information.

A portable fire extinguisher is located in operator's cab. The extinguisher should be checked daily to ensure that it is charged. The pointer on the charge gauge should point to the green region.

If the indicator falls out of this green area, the extinguisher should be serviced immediately.

Maintain a CHARGED fire extinguisher on the machine at all times and KNOW HOW TO USE IT. Refer to the manufacture's Use and Information manual for proper usage, additional information and recommended inspection and maintenance intervals.

3.8

Tigercat 726E Feller Buncher

Lubrication and Maintenance

SCHEDULED MAINTENANCE Clean: • Potentially damaging limbs or sticks from machine.

WARNING

• Air conditioner condensor, charge air cooler, oil cooler and radiator if required.

• Air intake precleaner compartment.

WARNING, HOT FLUIDS AND HOT MACHINE SURFACES CAN CAUSE SERIOUS BURNS!

Check: • All engine air intake system components (including charge air cooler) rubber elbows, connector hoses, tubes and clamps for damage, hardening, wear, cracks, leaks, loose clamps or loose hanger bracket hardware and repair or replace immediately.

• Charge Air Cooler for damage, wear, cracks, or leaks and repair immediately.

• For leakage around hydraulic components and flexible hoses.

• Before servicing the machine, allow the engine cooling system, fuel system, exhaust system, hydraulic system and machine surfaces to cool down.

• Use a thermometer to check surface and system temperatures to ensure it is safe to begin service work.

• DO NOT begin service work until the surface or system temperature has cooled down to below 100°F (38°C)!

EVERY 8 HOURS (EVERY SHIFT):

• For loose nuts, bolts and fittings.

• Check engine oil level

• Exhaust system for leaks.

• Drain fuel/water separator

• Condition and tension of accessory drive belt.

• Check air intake precleaner, clean as required

• Water pressure gauge in cab 4.14 Bar (60 psi) for pressurized water system.

• Check air cleaner unloader valve • Air intake primary filter element.

• Check air intake filter restriction indicator.

Replace primary filter if indicator is in red zone.

Replace secondary (safety) filter every third primary filter change to guarantee maximum performance and reliability.

If the water system has been operated, refer to PRESSURIZED WATER SYSTEM MAINTENANCE in THIS SECTION for refilling and charging instructions.

• Conduct an overall visual inspection.

• Refer to diesel engine service manual and attachment manual for additional required. maintenance at this scheduled time period.

• Check hydraulic oil level • Check pump drive gearbox oil level with dipstick • Check transmission oil level at dipstick • Lubricate mid drive shaft slip joint* 1-fitting, purge

EVERY 48 HOURS: • Check the center joint for looseness. Refer to CENTER JOINT MAINTENANCE in THIS SECTION for instructions. If a problem is found corrective action should be taken immediately. Refer also to CENTER JOINT in SECTION 11 of the SERVICE MANUAL for more detailed checking and adjustment procedures.

*Note: Lubricate mid drive shaft slip joint with machine articulated • Lubricate center joint bearings, 2-fittings, purge • Lubricate steering cylinder ends, 4-fittings, purge • Lubricate tilt and lift cylinder ends, 8-fittings, purge • Lubricate quick attach locking pins if applicable, 2-fittings, purge • Lubricate lift boom and tilt linkage, 9 or 10 fittings, depending on attachment), purge 3.9

Tigercat 726E Feller Buncher

Lubrication and Maintenance

SCHEDULED MAINTENANCE EVERY 125 HOURS:

EVERY 250 HOURS:

• Perform 8 hour maintenance

• Perform 8 hour maintenance • Perform 125 hour maintenance

And in addition:~ • Lubricate rear axle pivot, 2-fittings, purge • Lubricate front drive shaft slip joint 1-fitting, purge • Lubricate rear drive shaft slip joint 1-fitting, purge

And in addition replace: • Engine fuel filter • Engine fuel filter/water seperator • Oil in pump drive gearbox NOTE: Refer to the service manual section 8 for oil change procedure.

Check: • Engine coolant level • AC/Heater filters • Air intake primary filter element, check restriction indicator at FULL rpm • Fluid level in batteries unless maintenance free • Engine rpm.

• Hydraulic oil restriction indicator for boom/saw circuit with engine at FULL rpm • Hydraulic pump and motor securing bolts • Check fuel tank filler screen • Torque tightening points as per new machine maintenance • Proper operation of pressurized water system.

(Refer to PRESSURIZED WATER SYSTEM in SECTION 2 of the OPERATOR'S MANUAL and PRESSURIZED WATER SYSTEM MAINTENANCE in THIS SECTION)

• Oil in transmission NOTE: Refer to the service manual section 8 for oil change procedure.

• Refer to diesel engine service manual and attachment manual for additional required maintenance at this scheduled time period.

Check: • Parking brake oil level.

EVERY 500 HOURS:

Visually check for damage to: • Lift boom and tilt linkage • Front and rear frame • Center joint area • Attachment Make repairs immediately

• Perform 8 hour maintenance • Perform 125 hour maintenance • Perform 250 hour maintenance And in addition replace: • Hydraulic Oil pressure filter, drive charge pressure † • Hydraulic Oil return filters, boom/fan/steer/saw (high pressure)† • Lubricate door and door screen hinges.

Check: • All hydraulic pressures.

• Transmission mounting. Check, re-torque.

• Refer to diesel engine service manual and attachment manual for additional required maintenance at this scheduled time period.

Visually inspect for: • Frayed electrical wiring and hydraulic hose • Wear in any other components Clean/replace: • Air conditioner re-circulation filter • Cab fresh air filter • Refer to diesel engine service manual and attachment manual for additional required maintenance at this scheduled time period.

3.10

Tigercat 726E Feller Buncher

Lubrication and Maintenance

SCHEDULED MAINTENANCE EVERY 1000 HOURS:

EVERY 2000 HOURS:

• Perform 8 hour maintenance

• Perform 8 hour maintenance

• Perform 125 hour maintenance

• Perform 125 hour maintenance

• Perform 250 hour maintenance

• Perform 250 hour maintenance

• Perform 500 hour maintenance

• Perform 500 hour maintenance

And in addition replace : • Engine blow by filter.

• Perform 1000 hour maintenance

• Engine air cleaner unloader valve.

And in addition replace: • Oil in hydraulic tank.

• Strainer in accumulator charge valve.

• Hydraulic tank breather.

• Oil in axles, front and rear.

NOTE: Refer to the service manual section 8 for oil change procedure.

• Oil in hydraulic parking brake.

• Water in pressurized water system.

• Replace all air intake rubber components such as elbows and connectors - High temperatures in this area can cause the rubber to harden.

See AIR CLEANER MAINTENANCE in THIS SECTION.

And in addition: • Lubricate front and rear axle pinion grease seal. 1-fitting per axle, purge.

Check: • Intank fuel strainer.

• Check the center joint for looseness. Refer to CENTER JOINT MAINTENANCE in THIS SECTION for instructions. If a problem is found corrective action should be taken immediately. Refer also to CENTER JOINT in SECTION 11 of the SERVICE MANUAL for more detailed checking and adjustment procedures.

• Refer to diesel engine service manual and attachment manual for additional required maintenance at this scheduled time period.

• Check ALL air intake tubing, rubber couplings and band clamps for signs of wear and leakage and repair immediately.

• Refer to diesel engine service manual and attachment manual for additional required maintenance at this scheduled time period.

NOTE: When refilling the hydraulic system, vent pumps, motors and valves of air by opening a plug or hose fitting located near or on top of the pumps, motors and valves until oil free of air is seen flowing out of the plug or hose fitting. Failure to vent air from the hydraulic system could cause serious damage to hydraulic components. Tighten plugs or fittings and clean up any spilled oil when completed.

NOTE: Changing strainers, filters and replacing the hydraulic oil tends to aerate the oil. For maximum pump life, the machine should sit for 1 hour after servicing to allow entrained air to escape from the oil prior to applying working pressures to the pumps.

NOTE: Check all hydraulic system components especially cooling fan for proper operation after hydraulic oil has been replaced.

† Use of filters other than genuine Tigercat replacement filters is not recommended.

3.11

Tigercat 726E Feller Buncher

Lubrication and Maintenance

SCHEDULED MAINTENANCE SEASONAL: • Drain and refill hydraulic oil tank with recommended hydraulic oil. See "approved hydraulic oils".

• Drain and refill pressurized water system.

(Refer to PRESSURIZED WATER SYSTEM in SECTION 2 of the OPERATOR'S MANUAL and PRESSURIZED WATER SYSTEM MAINTENANCE in THIS SECTION)

3.12

Tigercat 726E Feller Buncher

Lubrication and Maintenance

APPROVED HYDRAULIC OILS

HYDRAULIC OIL OPERATING RANGE (Not suitable for axle applications)

OPERATING TEMP. RANGE LOWEST START-UP TEMP.

-40

OIL TYPE

-40

-30 -20

-20 0

HYDRAULIC OIL TEMPERATURE

-10

0

20

10

40

20

60

30

80

40

50

60

70

100

120

140

160

80 180

90 200

100

°C 220 °F

CITGO MYSTICK HVI 32 MYSTICK HVI 46 MYSTICK HVI 68 CHEVRON RANDO HDZ 22 RANDO HDZ 32 RANDO HDZ 46 RANDO HDZ 68 ESSO / EXXON UNIVIS ULTRA UNIVIS N22 UNIVIS N32 UNIVIS N46 UNIVIS N68 IRVING OIL HYDRAULIC LP 22 HYDRAULIC LP 32 HYDRAULIC LP 46 HYDRAULIC LP 68 MOBIL UNIVIS ULTRA MOBIL DTE 12M (ISO 22) MOBIL DTE 13M (ISO 32) MOBIL DTE 15M (ISO 46) MOBIL DTE 16M (ISO 68) PETRO-CANADA HYDREX EXTREME HYDREX XV HYDREX MV 22 HYDREX MV 36 HYDREX MV 60 SHELL TELLUS T22 TELLUS T32 TELLUS T46 TELLUS T68

CAUTION

OPERATING MACHINE OUTSIDE LIMITS SHOWN WILL RESULT IN FAILURE OF HYDRAULIC COMPONENTS

5168AR04

3.13

Tigercat 726E Feller Buncher

Lubrication and Maintenance

3.14

Tigercat 726E Feller Buncher

Lubrication and Maintenance Tigercat Model 726E SERVICE AND LUBRICATION POINTS

REFER TO Tigercat OPERATOR'S MANUAL FOR FURTHER INFORMATION

CHK

2

ENGINE OIL AND FILTER

3

FUEL FILTER

4

FUEL/WATER SEPARATOR

5

FUEL CAP SCREEN

6

BLOW BY FILTER

7

DEF SUPPLY MODULE FILTER

8

IN TANK FUEL STRAINER

9

AIR INTAKE PRECLEANER

CHK

•

53

14

•

•

REP DRN

QTY

2000 

1000 

500 

CHANGE COOLANT EVERY 2 YEARS

DESCRIPTION USG

CHK

250 

8

COOLING SYSTEM

CAPACITY LITERS

1

125 

SERVICE POINT NO.

SERVICE EVERY ITEM

60% ANTIFREEZE/40% DISTILLED WATER 1• 1•

REP

1

CHK REP † CHANGE FILTER EVERY 2 YEARS CHK

• SEE ENGINE MANUFACTURER'S MAINTENANCE MANUAL FOR PROCEDURES, CAPACITIES AND REPLACEMENT INTERVALS

1

CLEAN OR REPLACE AS NECESSARY

1

SEE ENGINE MANUAL FOR PROCEDURES

1

REFER TO SECTION 3 OF THE MANUAL FOR DETAILS.

1

DRAIN TANK, CLEAN OR REPLACE AS NECESSARY

1

CLEAN AS REQUIRED / INSPECT IMPELLER FOR WEAR OR DAMAGE REPLACE AS NECESSARY

10

AIR INTAKE PRIMARY FILTER ELEMENT

CHK

1

11

AIR INTAKE SAFETY FILTER ELEMENT

CHK

1

CHECK FILTER RESTRICTION INDICATOR. REFER TO 8 HOUR SCHEDULED MAINTENANCE FOR DETAILS (SECTION 3 IN MANUAL).

12

AIR CLEANER UNLOADER VALVE

CHK

1

REFER TO SECTION 3 IN MANUAL

13

AIR INTAKE CONNECTIONS

CHK

2

CHECK FOR LOOSE CLAMPS AND DAMAGED RUBBER COMPONENTS. REPLACE RUBBER COMPONENTS.

14

HYDRAULIC OIL FILTER STEER/FAN/BOOM/SAW

1

WATER ABSORBING (BLUE)

15 16

HYDRAULIC TANK

17

HYDRAULIC TANK BREATHER

18

HYDRAULIC OIL FILTER HYDRAULIC DRIVE CHARGE PRESSURE

REP †

19

A/C & HEATER FILTERS

REP †

20

PUMP DRIVE GEARBOX

CHK

D/R

21

TRANSMISSION

CHK

D/R

22

AXLES: FRONT REAR

D/R D/R

23

PINION GREASE SEAL - FRONT/REAR AXLE

LUB

MID DRIVE SHAFT

CHK

ACCUMULATOR CHARGE VALVE STRAINER

28

ATTACHMENT

29

PRESSURIZED WATER SYSTEM

1

2 4.9

1.3

4.9

1.3

26.5 24.6

7.0 6.5

PURGE

CLEAN OR REPLACE AS NECESSARY CHECK OIL LEVEL. FILL WITH MIL-L-2105C OR API-GL-5 BELOW -10ºF(-23ºC) USE 75W-90 UP TO 100ºF(38ºC) USE 80W-90 ABOVE 100ºF(38ºC) USE 85W-140

2

ONE FITTING PER AXLE LITHIUM BASE EP2 GREASE

1 PURGE

LUB LUB

DRAIN AND REFILL AT SEASONAL OIL CHANGE REFER TO MANUAL FOR APPROVED OILS †† CHECK USING VEHICLE DISPLAY MODULE

47

LUB

CHK 48 

27

178

1

LUB **

CENTER JOINT BEARING PRELOAD

PARKING BRAKE

D/R †† REP

CENTER JOINT

26

3

CHK

REAR DRIVE SHAFT 25

REP REP †

FRONT DRIVE SHAFT 24

REP

1

LITHIUM BASE EP2 GREASE 

1 PURGE

2

CHK

LITHIUM BASE EP2 GREASE  REFER TO SECTION 3 OF THE MANUAL FOR DETAILS.

CHK

D/R

REP

0.5

FILL WITH ML-L-2105C OR API-GL-5 LUBRICANT GRADE/WEATHER TEMPERATURE: BELOW -10ºF(-23ºC) USE 75W-90 UP TO 100ºF(38ºC) USE 80W-90 ABOVE 100ºF(38ºC) USE 85W-140

0.13

1 SEE ATTACHMENT MANUFACTURER'S MANUAL

CHK TEST

D/R

CHECK SYSTEM PRESSURE, 60 PSI REFER TO SECTION 2 OPERATOR'S MANUAL.

61655ENG R0

3.15

Tigercat 726E Feller Buncher FILTERS - REMOVE AND REPLACE IMPORTANT! Failure to service and replace filters at the proper intervals specified in the manufacturer's manuals, could cause damage to the machine and result in the product warranty becoming NULL and VOID. Check Tigercat parts catalog for replacement filters.

Refer to the engine manufacturer's operation and maintenance manual for correct procedures and time intervals when servicing the engine oil and fuel filters. Read and understand the SAFETY section in each of these manuals.

ENGINE OIL FILTER

M726E-081

ENGINE COMPARTMENT, LEFT SIDE FUEL FILTER

Lubrication and Maintenance FUEL FILTER AND FUEL FILTER/WATER SEPARATOR The fuel filter is supplied with the engine. Refer to the engine manufacturer's operation and maintenance manual for service information and replacement interval.

The fuel filter/water separator is a combination unit, with a replaceable fuel filter and a removable water sediment bowl on the bottom of the unit.

The water sediment bowl is only replaced if it becomes damaged or non-functional. For service and replacement intervals see SERVICE AND LUBRICATION POINTS in THIS SECTION. If the fuel supply is dirty, the fuel filter must be replaced more frequently than recommended in the owner’s manual. Operating the machine with a clogged fuel filter will result in low engine power. It is also recommended that the fuel/water separator bowl be drained daily.

When installing a new fuel filter, DO NOT pre-fill with diesel fuel, or engine fuel pump damage will result. This type of failure is not warrantable by the engine manufacturer.

Unfiltered fuel used to pre-fill filters enters directly into the fuel system. Contaminants in unfiltered fuel can cause significant and costly damage to the engine. The cleanliness of fuel cannot be guaranteed unless it is always pre-filtered before use.

IMPORTANT! Filters that are an integral part of the engine (fuel and lubricating oil) should be serviced and replaced according to the engine manufacturer's operation and maintenance manual.

M726E-085

ENGINE COMPARTMENT, RIGHT SIDE

To prolong the operating life of the fuel filter, ensure that the fuel supply storage tank is clean and free of water and that the fuel is pre-filtered prior to adding it to the machine.

FUEL FILTER/WATER SEPERATOR

726E-078

HYDRAULIC COMPARTMENT, REAR 3.16

Tigercat 726E Feller Buncher

Lubrication and Maintenance

Changing the fuel filter/water separator:

HAND PRIMER

1. Park the machine on level ground, lower the attachment to the ground, stop engine.

2. Wipe clean the area around the filter and head.

3. Attach a hose to the spout on the bowl drain and place a suitable drain pan under separator bowl drain hose.

4. Loosen vent plug on filter head, open drain on separator bowl and drain fuel into pan.

FUEL FILTER/WATER SEPARATOR

5. Disconnect the fuel heater and water in fuel sensor from the wiring harness.

6. Remove the water separator filter and bowl from the filter head.

DRAIN VALVE WATER IN FUEL SENSOR

7. Remove and discard the gasket from the filter head.

8. Remove the water sediment bowl from the bottom of the old filter. Discard this gasket also. Dispose of old filter and any fuel properly.

726E-078

9. Clean the water sediment bowl, seating area for the gaskets on the filter head and the sediment bowl and close bowl drain.

FUEL FILTER / WATER SEPARATOR

PRIMER PUMP GASKET

10. Lubricate gasket for bottom of filter and water sediment bowl with clean engine oil and carefully hand tighten the water sediment bowl onto the new filter. Close the water drain valve.

FUEL / WATER SEPARATOR

11. Lubricate the gasket on top of the new filter with clean engine oil.

GASKET WATER SEPARATOR BOWL

12. Screw the new filter onto the filter head until the gasket makes contact with the seat and then hand tighten an additional 3/4 turn only.

BOWL DRAIN

13. Reconnect the fuel heater and water in fuel sensor to the wiring harness.

14. Use primer pump to refill filter until fuel free of air flows from vent on top of filter head, then tighten vent plug.

FUEL/WATER SEPARATOR

WARNING

15. Start the engine and check for leaks.

Drain fuel filter into a container and dispose of all fluids properly.

16. Clean up any spilled fuel before returning machine to operation.

IMPORTANT !

Filters that are an integral part of the engine (fuel and lubricating oil) should be serviced and replaced according to the engine manufacturer's manual.

3.17

Tigercat 726E Feller Buncher

Lubrication and Maintenance

FUEL TANK STRAINER FUEL TANK

CLEANOUT COVER

O-RING

STRAINER

726-008.PLT

FUEL TANK STRAINER

This is a stainless steel fuel strainer, screwed on to the inlet pipe of the engine fuel feed line inside at the bottom of the fuel tank.

Changing or cleaning the strainer: 1. Park machine on level ground, install articulation lock pin, lower attachment to the ground, stop engine, engage parking brake and block wheels.

2. Drain the fuel tank. (plug in bottom) 3. Remove the round fuel tank cleanout cover plate and O-ring from the access hole.

4. Before removing the strainer, clean any debris from the bottom of the tank and wipe it clean.

5. Remove the fuel strainer using the hex on the end of strainer. Carefully clean the strainer (it may be damaged by rough handling).

6. Check for a buildup of foreign materials where the strainer threads on to the pipe and elbow.

7. Reinstall the strainer using the hex on end.

8. Reinstall fuel tank cover plate with O-ring.

9. Refuel and check for leaks. Start the engine and check for leaks again.

3.18

Tigercat 726E Feller Buncher

Lubrication and Maintenance

DEF SUPPLY MODULE FILTER

IMPORTANT! It is important to avoid contamination of DEF when performing maintenance on the system as this may cause costly damage to SCR system components and affect the proper operation of the SCR system and the engine.

SUPPLY MODULE

FILTER COVER

SUPPLY MODULE

SPACER M726E-070

DEF TANK COMPARTMENT

O-RING

The supply module is located in the top of the DEF tank compartment in the left rear corner of the machine. The supply module filter can be accessed through the hinged access door in the DEF tank compartment. The DEF supply module filter should be replaced as part of scheduled maintenance every 2 years.

FILTER

O-RING

Changing a pressure filter: 1. Park machine on level ground, lower the attachment to the ground, stop engine.

SPACER

2. Wipe clean the area around the filter and supply module.

FILTER COVER

3. Turn the filter cover counterclockwise to remove filter and cover from the supply module.

O-RING

630E-001

DEF SUPPLY MODULE FILTER

WARNING

4. Place rags below to catch the spills.

Use only diesel exhaust fluid (DEF) which meets ISO 22241 specifications. DEF fluid is sprayed into the exhaust system at high temperatures during normal operation of the Selective Catalytic Reduction (SCR) after treatment system.

5. Remove the filter by unscrewing it from the filter cover.

6. Replace the large o-ring in the filter cover.

Lubricate with clean DEF solution for easy installation.

NEVER fill the DEF tank with any other fluid.

Doing so may cause a fire risk which could result in death or serious injury.

7. Replace the filter by screwing it onto the filter cover until hand tight (1/4 turn).

8. Reinstall the filter and cover turning clockwise and tighten to 20 Nm (15 lbf-ft).

9. Start the engine and check for leaks.

3.19

Tigercat 726E Feller Buncher

Lubrication and Maintenance

DRAINING THE DIESEL EXHAUST FLUID TANK The DEF tank is located in the compartment in the left rear corner of the machine. The DEF tank fill cap can be accessed through a door on the front of that compartment.

DEF TANK (BLUE FILL CAP)

DEF TANK FILL CAP ACCESS DOOR

41581AUNI R0

DRAIN PLUG

DEF TANK REMOVABLE ACCESS COVER

M726E-070

M726E-070

DEF TANK COMPARTMENT

1. The DEF tank is equipped with a drain.

2. Use the DEF level indicator on the computer display to estimate the container capacity required to properly drain the DEF solution. Refer to DIESEL EXHAUST FLUID (DEF) TANK in SECTION 2 of the OPERATOR'S MANUAL for tank capacity.

3. Remove the bolts from the DEF tank removable access cover and remove cover.

4. Loosen the DEF tank by removing the four mounting bolts.

5. Raise the DEF tank up just enough to gain access to the drain plug.

6. Remove the DEF tank filler cap.

7. Remove the drain plug and drain the DEF solution into a suitable container.

8. Once the fluid has been drained replace the drain plug, filler cap and mounting bolts.

9. If any DEF fluid has spilled, rinse well with water.

NOTE: To avoid contamination and ensure clean fluid, do not re-use DEF. Re-fill tank with new DEF only.

3.20

DEF TANK COMPARTMENT

Tigercat 726E Feller Buncher

Lubrication and Maintenance

HYDRAULIC OIL RETURN FILTERS RETURN MANIFOLD

IMPORTANT! NEVER PRE-FILL HYDRAULIC FILTERS

CHARGE PRESSURE FILTER

(4) HYDRAULIC RETURN FILTERS

M726E-110

HYDRAULIC FILTER SERVICING GUIDELINES

RETURN FILTER BY-PASS PRESSURE SWITCH

Tigercat generally does not recommend the prefilling of spin-on filters due to the risk of damage to the hydraulic system caused by unfiltered oil.

Unfiltered oil used to pre-fill filters enters directly into the hydraulic circuit. Contaminants in unfiltered oil can cause significant and costly damage to hydraulic valves, pumps and motors. The cleanliness of hydraulic oil cannot be guaranteed unless it is always prefiltered before use.

WATER ABSORBING ELEMENT (COLOR BLUE)

Use of hydraulic oil filters other than the Tigercat brand is not recomended.

REAR HYDRAULIC COMPARTMENT The return oil entering the hydraulic tank passes through four replaceable filters mounted on filter heads beside the tank and two mesh type reusable strainers one on the end of each return tube in the reservoir. For service and replacement intervals see SERVICE AND LUBRICATION CHART in THIS SECTION.

Changing the filters:

There is a bypass valve built into each filter head preset at 25 psi (1.7 bar), which will open in the event the elements become restricted. Before this valve is activated, a 20 psi (1.4 bar) filter restriction switch, located on the return manifold, will generate a critical message on the computer screen.

3. Place rags below to catch the spillage of oil.

1. Park machine on level ground, install articulation lock bar, lower attachment to ground, stop engine, engage parking brake and block wheels.

2. Wipe clean the area around the filter and head.

4. Wearing face protection (in case of an oil squirt), unscrew the old filter. Dispose of old filter and any oil properly.

5. Check the seating area for the gasket on the filter head and wipe it clean.

6. The Tigercat spin-on filter element is supplied with two gaskets. The M726E uses the round (O-ring style) section gasket for all the return filters. Discard the square section gasket.

Return Oil Filters Bypassed. Slowly warm up machine or service if already warm..

FILTER HEAD

IMPORTANT! Contaminated hydraulic fluid can lead to premature failure of hydraulic components and costly repairs.

Filters must be replaced at the recommended time intervals, Refer to SCHEDULED MAINTENANCE in THIS SECTION.

GASKET

FILTER ELEMENT FILTR_SEALS2

ROUND SECTION GASKET INSTALLATION

7. Remove used gasket and clean gasket seat in head.

3.21

Tigercat 726E Feller Buncher

Lubrication and Maintenance

8. Apply clean oil to new round gasket surfaces.

9. Install new round section gasket into inside lip of filter.

10. Screw on new filter until filter makes contact with filter head.

11. Tighten filter until top edge makes metal to metal contact with head. (Approximately 1 1/2 additional turns after gasket contact) 12. Start the engine and check for leaks.

3.22

Tigercat 726E Feller Buncher

Lubrication and Maintenance

HYDRAULIC OIL RETURN STRAINERS

HYDRAULIC RETURN STRAINERS

M726E-071

CUT AWAY OF HYDRAULIC TANK

There are two reusable strainers on the return tubes. The strainers should be inspected whenever the hydraulic tank is drained. See SCHEDULED MAINTENANCE in THIS SECTION. CHANGING OR CLEANING THE STRAINER: This should be performed in the event of a pump failure or hydraulic oil contamination.

1. Park machine on level ground with the attachment resting on the ground.

2. Stop engine.

4. Turn BATTERY DISCONNECT SWITCH to the 'OFF' position.

6. Drain the hydraulic tank into a suitable container via a drain plug in the bottom of the tank.

8. Before removing the strainers, clean any debris from the bottom of the tank and wipe it clean.

9. Remove the two hydraulic oil return strainers using the hex on the end of strainer. Carefully clean the strainers (they may be damaged by rough handling).

10. Check for a buildup of foreign materials where the strainers screw onto the pipes.

11. Reinstall the strainers using the hex on end.

12. Reinstall access cover with NEW o-ring.

13. Add hydraulic oil to tank using fill pump.

15. Bleed air from the main, attachment and fan pumps by loosening the case drain hose fittings at each pump connection.

16. Continue filling hydraulic tank using fill pump.

Tighten case drain hose fittings to pumps when oil is seen coming from the pump case drain ports. It is important that all air is evacuated from the pumps.

17. Fill hydraulic tank up to FULL mark on sight gauge using fill pump.

18. Recheck oil level and add hydraulic oil up to FULL mark using fill pump.

NOTE: Changing strainers and filters and replacing the hydraulic oil tends to aerate the oil. For maximum pump life, the machine should sit for 1 hour after servicing to allow entrained air to escape from the oil prior to applying working pressures to the pumps.

STRAINER ACCESS COVER

7. Remove the round top access cover and o-ring.

3.23

Tigercat 726E Feller Buncher

Lubrication and Maintenance

HYDROSTATIC DRIVE CHARGE PRESSURE FILTER

HYDRAULIC FILTER SERVICING GUIDELINES IMPORTANT! NEVER PRE-FILL HYDRAULIC FILTERS

726E-079

Tigercat generally does not recommend the prefilling of spin-on filters due to the risk of damage to the hydraulic system caused by unfiltered oil.

Unfiltered oil used to pre-fill filters enters directly into the hydraulic circuit. Contaminants in unfiltered oil can cause significant and costly damage to hydraulic valves, pumps and motors. The cleanliness of hydraulic oil cannot be guaranteed unless it is always prefiltered before use.

CHARGE PRESSURE FILTER

REAR HYDRAULIC COMPARTMENT

The charge pressure filter is located in the rear hydraulic compartment and is on the output side of the hydrostatic drive charge pump. For service and replacement intervals see SERVICE AND LUBRICATION CHART in THIS SECTION. Changing the filter: 1. Park machine on level ground, install articulation lock bar, lower attachment to ground, stop engine, engage parking brake and block wheels.

3. Wipe clean the area around the filter and head.

4. Place rags below to catch the spillage of oil.

5. Wearing face protection (in case of an oil squirt), unscrew the old filter. Dispose of old filter and any oil properly.

6. Check the seating area for the gasket on the filter head and wipe it clean.

7. The new filter has an attached gasket. Apply hydraulic oil to the gasket surface.

8. Screw on the new filter until the gasket makes contact with the seat in the filter head.

9. Hand tighten filter an additional 1/2 turn only.

11. Start the engine and check for leaks.

3.24

Tigercat 726E Feller Buncher

Lubrication and Maintenance

AIR CLEANER MAINTENANCE

AIR FILTER RESTRICTION INDICATOR ELECTRICAL RESTRICTION INDICATOR SWITCH

MECHANICAL AIR FILTER RESTRICTION INDICATOR

M726E-074

M726E-075

A filter restriction switch is installed on the outlet side of the air cleaner, the switch is used to signal the MD3 computer when the filter is restricted.

SAFETY ELEMENT

Engine Air Intake Filter Restricted. Service Machine to correct.

PRIMARY ELEMENT 470-04

AIR FILTER ELEMENTS

The air cleaner on this machine uses two filter elements; a primary element and a safety element.

It is accessible through the hydraulic compartment access door on the rear of the machine.

To ensure maximum engine protection, it is important that the elements be serviced correctly and at proper servicing intervals.

NOTE: Replace the safety element every third primary filter change.

An alert warning message will appear on the MD3 display to indicate the engine air intake filter is restricted. Replace the primary air filter element if the alert message is displayed. Replace the secondary (safety) filter every third primary filter change to guarantee maximum performance and reliability.

A mechanical filter restriction indicator is also connected to the outlet side of the air filter.

Replace the primary air filter when the indicator shows RED. This indicator provides a continuous reading whether the engine is running or is shut down. After replacing the filter, reset the indicator by pressing the reset button.

NOTE: Replace the safety element every third primary filter change.

3.25

Tigercat 726E Feller Buncher

Lubrication and Maintenance

ENGINE AIR PRECLEANER

HOW IT WORKS

ENGINE AIR PRECLEANER

3

3 4

2 1 5

480-017

M726E-073

The engine air precleaner cleans engine air before it reaches the air cleaner filter elements. It removes contaminants such as dust, powder, insects, rain and snow. This precleaner is self powered and self cleaning requiring virtually no maintenance.

However, it should be checked periodically to make sure that foreign materials have not plugged the intake area or the exhaust port area.

NOTE: The precleaner compartment should be checked and cleaned out daily to ensure proper operation of the precleaner.

NOTE: Periodically remove the precleaner assembly and check the spinner assembly for wear or dirt build-up on the blades. Clean the spinner assembly or replace it if the blades are worn.

1. Dirty air (1) enters the Precleaner, which is clamped onto the engine air intake.

2. Specially-designed vanes (2) , curved and angled to precisely direct air flow, move the dirty air toward the stainless steel impeller (3).

3. The dynamically balanced, one piece impeller (3) (only moving part) creates a tornado inside the housing.

4. The centrifugal force of the tornado expels the heavier than air dirt particles (4), chaff, dust, snow, rain, etc., out the discharge louver 5. Cleaned air (5) enters the engine air cleaner intake pipe, and the filter element has only the very light particles to remove.

RESULTS • Cleaner Air for The Engine!

• Longer Filter Element Life!

• Increased Engine Life!

• Increased Engine Performance!

• Reduced Operating Costs!

3.26

Tigercat 726E Feller Buncher

Lubrication and Maintenance

AIR CLEANER UNLOADER VALVE

The most common and damaging servicing problems are: OVER SERVICING Filter elements increase in dust cleaning efficiency as dust builds up on the media. Looks can be deceiving. A filter that looks dirty may actually be more efficient than one that is clean. A filter with dust build up on the media reaches nearly 100% dust cleaning efficiency. Only when a filter is so clogged with dirt that air restriction goes beyond engine manufacturer's guidelines, should a filter be replaced.

UNLOADER VALVE

NOTE: This does not apply to hydraulic oil or diesel engine oil filters.

SERVICING Engine exposure to dust during servicing is a large reason for engine damage due to dust.

M726E-076

This rubber valve on the tube of the air cleaner housing should be checked before every shift (8 hours). If this valve is missing, damaged or has turned hard, it will cause the air cleaner to become ineffective. The valve should suck closed at 1/3 throttle.

Abrasive dust can easily enter the intake system once the air cleaner cover and protective filter element are removed for replacement. The safety element does reduce this risk but it should also be replaced at every third primary element change.

This valve should be replaced every 1000 hours.

Remove the unloader valve from the tube of the air cleaner housing. Check and clean the valve.

A good valve is soft and flexible. If plugged, be sure to check the filter elements as they may need replacing as well. Reattach the valve to the tube.

When operating in high dust conditions, the unloader valve should be checked and squeezed every 2 hours to release dust buildup.

In addition refer to the LUBRICATION AND MAINTENANCE SCHEDULE in AIR CLEANER MAINTENANCE in SECTION 3 of THIS MANUAL.

3.27

Tigercat 726E Feller Buncher

Lubrication and Maintenance INTAKE TUBING AND JOINTS Check all air intake system components, rubber elbows, connector hoses, tubes and clamps for damage, hardening, wear, cracks, leaks, loose clamps or loose hanger bracket hardware and repair or replace immediately.

SAFETY ELEMENT

Replace all air intake rubber components such as elbows and connectors every 2000 hours - High temperatures in this area can cause the rubber to harden.

PRIMARY ELEMENT 470-04

AIR FILTER ELEMENTS

IMPORTANT STEPS TO FOLLOW WHEN CHANGING FILTER ELEMENTS 1. Release the six overcenter latches and lift cover/dust bowl off of air cleaner assembly .

2. Avoid dislodging dust from filter element(s) by gently pulling the element off the outlet tube.

3. Always clean the sealing surface of the outlet tube before inserting a new filter element.

4. Always clean the inside of the outlet tube.

5. Check your old filter sealing surfaces. This will help you detect foreign material on the sealing surface that is causing leakage.

NOTE: Filter elements should never be cleaned and reused. Cleaning causes dust to bypass the filter and be deposited on the inner surface of the filter media. The dust is then drawn directly into the engine.

6. Inspect the new filter for damage.

7. Insert the new filter properly. Apply pressure to the outer rim of the filter not the flexible centre.

8. Check connections and ducts for an air tight fit.

Ensure that all clamps, bolts and connections are tight. Check rubber elbows intake tubing and joints for hardening cracks, splits or wear points and replace as needed. Leaks in these locations send dust directly to the engine.

3.28

Tigercat 726E Feller Buncher

Lubrication and Maintenance

SELECTIVE CATALYTIC REDUCTION AFTER TREATMENT SYSTEM (DENOX 2 SYSTEM)

The SCR after treatment system consists of the following components:

The engine on this machine is equipped with a Selective Catalytic Reduction (SCR) after treatment system to limit the nitrogen oxide exhaust gas values (NOX) to meet Tier 4i emission standard requirements with low fuel consumption.

This process is electronically controlled by the DENOX 2 system.

The SCR process is based on series of chemical reactions which involve the reaction of ammonia with the oxygen in the exhaust gas to reduce nitrogen oxides (NOX) in the exhaust gas by transforming it into inert compounds: free nitrogen (N2) and water vapour (H2O).

EXHAUST OUTLET TEMPERATURE SENSOR

EXHAUST INLET TEMPERATURE SENSOR

• • • • • • • • • • •

MIXER TUBE

Diesel Exhaust Fluid (DEF) Tank Heater Valve and Heated DEF Supply Lines DENOX Dosing Control Unit (DCU) Supply module Dosing Module (DEF Injector) Mixer Tube Catalytic Converter Exhaust Inlet Temperature Sensor Exhaust Outlet Temperature Sensor NOX Sensor Humidity Sensor

DOSING MODULE

CATALYTIC CONVERTER AIR CLEANER

NOx SENSOR EXHAUST PIPE

HUMIDITY SENSOR AIR INTAKE PIPE SUPPLY MODULE DEF HEATER UNIT

HEATER VALVE

DEF TANK

M726E-114

SCR AFTER TREATMENT SYSTEM COMPONENTS 3.29

Tigercat 726E Feller Buncher

Lubrication and Maintenance SUPPLY MODULE/DENOX DCU (CIRCULATING AND DOSING DEF FLUID)

HEATER VALVE (CIRCULATING ENGINE COOLANT)

PM - PARTICULATE MATTER HC - HYDROCARBONS NOX - NITROGEN OXIDES CO - CARBON MONOXIDE NH3 - AMMONIA N2 - FREE NITROGEN H2O - WATER

HUMIDITY SENSOR

DOSING MODULE

MIXER TUBE

NOx SENSOR

CATALYTIC CONVERTER

TEMPERATURE SENSORS

SCR AFTER TREATMENT SYSTEM The SCR after treatment system is electronically managed by the DCU (Dosing Control Unit) incorporated in the supply module. The DCU calculates and adjusts the flow rate of the DEF solution into the system based on current engine speed, torque delivered, exhaust temperature, amount of nitrogen oxides present and humidity levels in intake air.

470-040

The supply module pump picks up the DEF solution from the tank and sends it under pressure to the dosing module (DEF injector) and mixer tube to be injected into the exhaust pipe upstream of the catalytic converter.

The first phase of the process takes place in the first part of the catalytic converter: high temperature exhaust gas evaporates the DEF solution instantly and, by hydrolysis, converts it into ammonia (2NH3) and carbon dioxide (CO2).

Evaporation of the solution lowers exhaust gas temperature, bringing it closer to the optimum temperature required by the process.

The exhaust fumes and ammonia at the proper reaction temperature, are introduced into the catalytic converter, where the second phase of the process takes place: by reacting with the oxygen in the exhaust gases the ammonia is converted into free nitrogen (N2) and water vapour (H2O).

NOTICE

• DO NOT IDLE THIS ENGINE FOR MORE THAN 4 HOURS. • DAMAGE TO EMISSION CONTROL SYSTEM WILL RESULT.

59912BENG R0

IMPORTANT !

Engine should not idle longer than 4 consecutive hours. Damage to the emission control system will result. When this machine idles for an extended period excess hydrocarbon buildup is created in the SCR after treatment system. Burn off of excess hydrocarbon at full load immediately after a long idle period will generate excess heat which will cause damage to emission control system components. It will take 45 minutes at 40% load (or an SCR exhaust outlet temperature of 320°C (608°F)) to burn off the hydrocarbon that accumulates during a 4 hour long idle.

3.30

Tigercat 726E Feller Buncher

Lubrication and Maintenance

DIESEL EXHAUST FLUID (DEF) TANK

DEF TANK (BLUE FILL CAP) 41581AUNI R0

COOLANT HEATER COIL

DEF TANK

LEVEL SENSOR

TEMPERATURE SENSOR

M726E-070 620E-082

The DEF tank is located in the compartment in front of the hydraulic tank in the left rear corner of the machine. The DEF tank fill cap can be accessed through the hinged door on the front of that compartment. The DEF tank fill point is equipped with a filter to prevent contaminants from entering the tank.

HEATER UNIT

Diesel exhaust fluid (DEF) is used by the Selective Catalytic Reduction (SCR) after treatment system to lower the concentration of nitrogen oxides from the diesel engine exhaust of this vehicle. DEF is an aqueous urea solution with 32.5% high purity urea and 67.5% deionized water. Note that DEF may also be referred to as AUS32 or AdBlue and should meet ISO 22241 specifications. Use only DEF meeting this standard.

DEF tank capacity is 43 L (11.4 US gal). DO NOT overfill tank. This tank is equipped with an expansion capacity of 7% required to allow for the expansion of DEF in cold temperature conditions.

DEF freezes at -11°C (12°F).

It is important to avoid contamination of DEF when filling the tank as this may cause costly damage to SCR system components and affect the proper operation of the SCR system and the engine.

IMPORTANT! DEF should be stored between -11°C (12°F) and 30°C (86°F) and out of direct sunlight to maximize shelf life and to avoid DEF quality problems caused by improper storage.

A DEF level indicator is shown on the main menu of the computer display, below the fuel gauge.

WARNING Use only diesel exhaust fluid (DEF) which meets ISO 22241 specifications. DEF fluid is sprayed into the exhaust system at high temperatures during normal operation of the Selective Catalytic Reduction (SCR) after treatment system.

NEVER fill the DEF tank with any other fluid.

Doing so may cause a fire risk which could result in death or serious injury.

The DEF tank includes a fill location, a drain, and a heater unit. The heater unit incorporates a heater coil, heating system inlet/outlet connections, DEF inlet/outlet connections, a breather, level sensor, temperature sensor and electrical connector.

When DEF levels are low or a problem with DEF quality is detected information messages and warnings will be shown on the computer display.

Note that extremely low DEF levels and/or DEF quality problems may result in derating of engine performance to meet emission standard requirements. Action to correct these problems should be taken immediately to avoid affecting engine performance and damage to SCR after treatment system components. Refer also to COMPUTER~MESSAGES AND WARNINGS in THIS SECTION. Refer to DRAINING DEF TANK in SECTION 3 of THIS MANUAL. Refer to DEF TANK in SECTION 2 of the OPERATOR'S MANUAL.

3.31

Tigercat 726E Feller Buncher

Lubrication and Maintenance

HEATER VALVE / HEATED DEF SUPPLY LINES

Heating is switched OFF when: • DEF tank temperature >16°C (61°F) • Supply module temperature >10°C (50°F) • Ambient air temperature >-4°C (25°F)

CONNECTOR

Heating is switched ON when: • DEF tank temperature <15°C (59°F) • Supply module temperature: +8°C (46°F) • Ambient air temperature: -5°C (23°F) When conditions require heating the system will thaw DEF within 30 minutes of engine start for proper operation of the SCR after treatment system. Note also that whenever the engine is stopped all DEF is pumped back to tank before the engine power system is turned off. This process takes approximately 90 seconds.

COOLANT OUTLET COOLANT INLET 620E-081

DENOX DOSING CONTROL UNIT (DCU)

HEATER VALVE

The heater valve is located inside the rear hydraulic compartment door under the return filters.

SUPPLY MODULE/ DENOX DCU DEF TANK

M726E-070

HEATER VALVE

DEF TANK COMPARTMENT

DENOX DCU is incorporated into the supply module located in the top of the DEF tank compartment in front of the hydraulic tank.

M726E-115

The heater valve controls the flow of engine coolant through the DEF tank heater coil. This machine is equipped with electrically heated DEF supply lines.

DEF freezes at -11°C (12°F).

Temperature sensors signals control the operation of both the electrically heated DEF supply lines and the heater valve which, depending on the temperature, opens or closes the flow of hot engine coolant in the heater coil.

The SCR after treatment system is electronically managed by the DCU (Dosing Control Unit) incorporated in the supply module. The DCU calculates and adjusts the flow rate of the DEF solution into the system based on current engine speed, torque delivered, exhaust temperature, amount of nitrogen oxides present and humidity levels incoming air.

The DCU is connected to the Engine ECU (electronic control unit).

3.32

Tigercat 726E Feller Buncher

Lubrication and Maintenance

SUPPLY MODULE

CATALYTIC CONVERTER AIR CLEANER

CATALYTIC CONVERTER

SUPPLY MODULE/ DENOX DCU DEF TANK

M726E-074

CATAYTIC CONVERTER

The catalytic converter is located on the right side of the hydraulic compartment at the rear of the machine.

M726E-070

DEF TANK COMPARTMENT

The supply module pump picks up the DEF solution from the tank and sends it under pressure to the dosing module mounted on the mixer tube to be injected into the exhaust pipe upstream of the catalytic converter.

DOSING MODULE (DEF INJECTOR)

DOSING MODULE

The catalytic converter is equipped with soundproofing material and replaces the exhaust silencer. Chemical reactions inside the catalytic converter reduce nitrogen oxides (NOX) in the exhaust gas.

The first phase of the SCR process takes part in the first part of the catalytic converter: high temperature exhaust gas evaporates the DEF solution instantly and, by hydrolysis, converts it into ammonia (2NH3) and carbon dioxide (CO2).

Evaporation of the solution lowers exhaust gas temperature, bringing it closer to the optimum temperature required by the process.

The exhaust fumes and ammonia at the proper reaction temperature, are introduced into the catalytic converter, where the second phase of the process takes place: by reacting with the oxygen in the exhaust gasses the ammonia is converted into free nitrogen (N2) and water vapour (H2O).

DOSING MODULE

MIXER TUBE

The dosing module is mounted on the mixer tube upstream of the catalytic converter. The dosing module injects DEF fluid into the exhaust pipe.

Note that this module must be mounted at the correct specified angle to function properly.

MIXER TUBE The mixer tube is mounted on the exhaust pipe upstream of the catalytic converter.

The insulated high-turbulence mixer tube is used to mix the DEF solution and exhaust gases together before they enter the catalytic converter.

3.33

Tigercat 726E Feller Buncher

Lubrication and Maintenance

EXHAUST TEMPERATURE SENSORS

The sensor, cable and control unit are considered to be one part for service/replacement purposes.

Note that cable length cannot be changed as this will affect the proper operation of the sensor.

TAG

IMPORTANT! When checking or replacing any sensor or plugs in the exhaust or the after treatment system it is important to use only approved anti-seize as specified by Tigercat. Use of nonapproved compounds can affect the operation of the NOX sensor and a malfunction of the SCR after treatment system. This may result in poisoning of the catalytic converter and require replacement of expensive after treatment system parts.

620E-087

EXHAUST TEMPERATURE SENSOR

Temperature sensors are mounted at the inlet and outlet of the catalytic converter. These sensors send inlet and outlet exhaust temperature signals to the Denox DCU. The DCU uses this information to calculate the amount of DEF fluid to be injected into the system.

Refer to APPROVED ANTISIEZE PASTES FOR EXHAUST / AFTER TREATMENT LINE (TIGERCAT BY FPT Tier 4i ENGINES) in SECTION 3 of THIS MANUAL. HUMIDITY SENSOR

Note that to distinguish between inlet and outlet temperature sensors the inlet exhaust temperature sensor has a black tag and the outlet exhaust temperature sensor has a brown tag.

NOX SENSOR ELECTRONIC CONTROL UNIT

620E-089

The humidity sensor is located on the air intake just past the air cleaner. This sensor monitors the temperature and humidity of intake air sending signals to the engine ECU and Denox DCU. This information is used to calculate the amount of DEF fluid to be injected into the system.

CERAMIC SENSOR

620E-088

HUMIDITY SENSOR

NOX SENSOR

The NOX sensor is mounted at the outlet of the catalytic converter. The NOX sensor detects and sends information about the dosing of DEF solution and the efficiency of the catalytic converter to the engine ECU and the Denox DCU. This information is used to to calculate the amount of DEF fluid to be injected into the system and to monitor SCR after treatment system operation.

The NOX sensor consists of ceramic sensor and an electronic control unit linked by a cable. The sensor detects the concentration of nitrogen oxides in the exhaust.

3.34

Tigercat 726E Feller Buncher

Lubrication and Maintenance

APPROVED ANTISIEZE PASTES FOR EXHAUST / AFTER TREATMENT LINE (TIGERCAT BY FPT Tier 4i ENGINES) Weicon High Tech Anti-seize IMPORTANT! When checking or replacing any sensor or plugs in the exhaust or the after treatment system it is important to use only approved anti-seize as specified by Tigercat.

Use of non-approved compounds can affect the operation of the NOX sensor and a malfunction of the SCR after treatment system. This may result in poisoning of the SCR catalyst and require replacement of expensive after treatment system parts.

DIESEL EXHAUST FLUID (DEF) HANDLING Diesel exhaust fluid (DEF) is an aqueous urea solution with 32.5% high purity urea and 67.5% deionized water. Note that DEF may also be referred to as AUS32 or AdBlue and should meet ISO 22241 specifications. Use only DEF meeting this standard.

It is important to avoid contamination of DEF as this may cause costly damage to SCR system components and affect the proper operation of the SCR system and the engine.

When a problem with DEF quality is detected information messages and warnings will be shown on the computer display. Note that DEF quality problems may result in derating of engine performance to meet emission standard requirements. Action to correct DEF quality problems should be taken immediately to avoid affecting engine performance and damage to SCR after treatment system components. Refer also to COMPUTER~MESSAGES AND WARNINGS in SECTION 2 of the OPERATOR'S MANUAL or SECTION 6 of the SERVICE MANUAL.

AVOID DEF QUALITY PROBLEMS WITH PROPER HANDLING PRACTICES Most DEF quality problems can be avoided entirely with a little care and proper handling of DEF fluid.

FILLING THE DEF TANK •

Always clean the area around the fill cap and avoid introducing contaminants into the DEF tank when filling.

•

Always use only diesel exhaust fluid (DEF) which meets ISO 22241 specifications. Use of any other fluid will contaminate the after treatment system and may pose a safety hazard.

USE OF PROPER STORAGE CONTAINERS •

To prevent contaminants from affecting DEF quality it should be handled only in storage, transport and filling containers intended exclusively for that purpose.

•

Polyethylene or stainless steel containers are recommended. Refer also to DEF manufacturer's recommendations.

•

DEF is corrosive to metals other than stainless steel. Transport in metal containers other than stainless steel will result in contamination.

PROPER STORAGE CONDITIONS TO MAXIMIZE SHELF LIFE •

DEF should be stored between -11°C (12°F) and 30°C (86°F) and out of direct sunlight to maximize shelf life and to avoid DEF quality problems caused by improper storage.

•

DEF quality problems can often be avoided with proper storage and handling practices to maximize shelf life.

•

DEF storage areas should always be out of direct sunlight and away from heat sources to avoid reducing shelf life.

•

DEF shelf life is limited. It should be consumed on a first in first out basis, within manufacturer's recommended shelf life limits.

DEF beyond manufacturer's recommended shelf life limits may not meet ISO 22241 specifications.

For safety information refer to DIESEL EXHAUST FLUID (DEF) in SECTION 1 of THIS MANUAL.

WARNING Use only diesel exhaust fluid (DEF) which meets ISO 22241 specifications. DEF fluid is sprayed into the exhaust system at high temperatures during normal operation of the Selective Catalytic Reduction (SCR) after treatment system.

NEVER fill the DEF tank with any other fluid.

Doing so may cause a fire risk which could result in death or serious injury.

3.35

Tigercat 726E Feller Buncher

Lubrication and Maintenance

PRESSURIZED WATER SYSTEM MAINTENANCE

FILL & CHARGE PRESSURIZED WATER SYSTEM

OPERATION:

1. Open water shut off valve and completely discharge all water and compressed air from the tank via the hose end nozzle.

Turn the hand operated ball valve (shut off valve) under the seat to the ON position to draw water from the 10.5 USgallon (39.7 liter) pressurized holding tank at the rear of the machine. When not in use turn the water supply OFF at this valve and relieve the pressure in the rubber hose, under the operator's seat.

HOSE

CAUTION Never remove fill plug before de-pressurizing tank or injury may result. This fill plug incorporates a vent hole to release air pressure from the tank before the threads disengage. DO NOT replace this fill plug with any substitute.

WATER SHUT OFF VALVE (SHOWN CLOSED)

9

196-16A

PRESSURIZED WATER SYSTEM CONTROL VALVE (UNDER SEAT)

TANK FILL PLUG

The pressure gauge on the side of the seat should read 60 psi.

AIR CHARGE VALVE

M726E-063

PRESSURE GAUGE

196-9A

PRESSURIZED WATER SYSTEM

2. Slowly unscrew fill plug two full turns. Any remaining air in the tank will be heard expelling from the special fill plug. Do not remove fill plug until all air has been expelled.

3. Close water shut off valve.

4. Fill tank with water. Tank capacity is approximately 10.5 USgallons (39.7 liters)

Refer also to FIRE PREVENTION in SECTION 1 of THIS MANUAL.

When temperatures below 0°C (32°F) are anticipated, use a 60/40 solution of Nontoxic R. V. Antifreeze or other suitable antifreeze.

Antifreeze solution must meet GM 6038M specifications.

SYSTEM TEST: This system should be tested once every month by turning the shut-off valve ON and expelling water from the hose end nozzle. A very forceful discharge of water should be obtained. If the water does not come out with force (with pressure gauge reading 4.14 Bar / 60 psi) the system needs to be PURGED. Refer to PURGING PRESSURIZED WATER SYSTEM in THIS SECTION.

PRESSURIZED WATER TANK

NOTE: Most Nontoxic RV Anti freeze solutions contain corrosion and algae inhibitors, it is therefore suggested that this solution be added to the water on a continual basis regardless of temperature conditions.

5. Install fill plug in tank.

After testing, the tank must be refilled and pressurized to 4.14 Bar / 60 psi. Refer to the following FILL AND CHARGE procedure. This FILL AND CHARGE procedure should be carried out yearly.

NOTE: This is a special plug designed to withstand pressurization of the water tank. Do not substitute.

3.36

Tigercat 726E Feller Buncher

Lubrication and Maintenance PURGING PRESSURIZED WATER SYSTEM

6. Pressurize the system to 4.14 Bar / 60 psi as indicated on pressure gauge by connecting an air hose to air charge valve beside the pressure gauge.

7. Open the water shut off valve

Purging should be carried out whenever the flow of water does not forcefully discharge from the end of the hose with the pressure gauge reading 4.14 Bar/60 psi.

8. Discharge about 1/2 US gallon (2 liters) of fluid into an empty antifreeze jug or other suitable container.

1. Open water shut off valve and completely discharge all water and compressed air from the tank via the hose end nozzle.

There will be significant foaming as the fluid is discharged into the jug. Continue until a very forceful flow is obtained and any contamination that may have been in the tank is flushed from the system.

CAUTION Never remove fill plug before de-pressurizing tank or injury may result. This fill plug incorporates a vent hole to release air pressure from the tank before the threads disengage. DO NOT replace this fill plug with any substitute.

9. Check fluid in the jug for contamination. If fluid is dirty dispose of it properly.

10. Close the water shut-off valve.

11. Release pressure and fluid from the hose.

12. Pressurize the system to 4.14 Bar / 60 psi as indicated on pressure gauge by connecting an air hose to air charge valve beside the pressure gauge.

13. Return the hose to its storage location.

2. Slowly unscrew fill plug two full turns. Any remaining air in the tank will be heard expelling from the special fill plug. Do not remove fill plug until all air has been expelled.

3. Close the water shut off valve and add 2 USgallons (8 litres) of clean water to the tank.

4. Install fill plug in tank.

NOTE: This is a special plug designed to withstand pressurization of the water tank. Do not substitute.

5. Pressurize the system to 4.14 Bar/60 psi as indicated on pressure gauge by connecting an air hose to air charge valve beside the pressure gauge.

6. Open the shut off valve and completely discharge all the water in the tank via the hose end nozzle.

7. Discharge all the water into an empty antifreeze jug or other suitable container.

There will be significant foaming as the fluid is discharged into the jug. Continue until a very forceful flow is obtained and any contamination that may have been in the tank is flushed from the system.

8. If a forceful discharge was not achieved, repeat the purging procedure. If a second purging does not work, remove lines and check for an obstruction.

9. After the purging operation, fill and charge the system as described in FILL & CHARGE PRESSURIZED WATER SYSTEM in THIS SECTION.

3.37

Tigercat 726E Feller Buncher

Lubrication and Maintenance

CHECKING THE AIR CONDITIONING SYSTEM

A/C COMPRESSOR

Any service work must be performed by authorized A/C technicians. The system should be charged with R134a refrigerant only. PAG (polyalkeylene glycol) oil should be present in the system and must be used on 'O' ring fittings during assembly.

WATER PUMP PULLY SERPENTINE BELT

A/C SYSTEM TOTAL CAPACITIES R134a REFRIGERANT 1.7 kg (3.75 lbs)

PAG OIL (polyalkylene glycol) 0.06 kg (2 oz)

ALTERNATOR

The compressor and charge valves are accessed from the right side engine compartment. The condenser core and receiver drier are accessed on the left side of the machine.

Use this checklist to maintain system between service intervals. a. Check compressor drive belt tension. b. Check air intake filters and precleaner and clean as required.

BELT TENSIONER

CHECK SERPENTINE BELT IMPORTANT: It is recommended that during cold weather when the A/C system is not in use, that it be run for a period of 5 minutes every 2 weeks. This will circulate oil to all components of the A/C system.

470-05

CAUTION Use compressed air for cleaning only when the machine is cold to avoid the risk of fire caused by debris contacting hot surfaces.

If using compressed air for cleaning, use at 2.07 Bar (30 psi) or less.

Always use personal protective equipment to guard against flying debris

A/C CONDENSER CORE

RECEIVER DRYER

CAUTION M726E-090

c.

Avoid the risk of fire caused by debris accumulating on surfaces that may become hot during machine operation. Always use care when cleaning to ensure that debris removed from one area of the machine does not accumulate on other areas of the machine.

CHECK A/C CONDENSER CORE

Check the condenser core for dirt and debris.

Clean as required. Refer to CLEANING A/C CONDENSER AND COOLING ASSEMBLY in SECTION 2 of the OPERATOR'S MANUAL.

d. Check the evaporator core and the inside of the A/C housing for dirt and debris. Clean as required. e. Run air conditioning system for 3 - 5 minutes. f.

Check to see that compressor clutch will engage.

3.38

Tigercat 726E Feller Buncher

Lubrication and Maintenance

CENTER JOINT

TRANSMISSION:

MAINTENANCE OF CENTER JOINT Maintenance in this area is usually limited to:

By carefully following these procedures, the service life of the transmission will be extended and costly down time will be avoided.

a) Regular lubrication of the two center joint grease fittings to purge the pivot bearings of debris and water. Refer to SERVICE AND LUBRICATION POINTS in THIS SECTION for lubrication intervals. Use only high quality, lithium based EP2 grease containing molybdenum disulphide.

For additional information, refer to TRANSMISSION in SECTION 8 of the SERVICE MANUAL. TRANSMISSION OIL LEVEL DIPSTICK AND FILL TUBE

b) Visually checking the center joint pivot for looseness every 1000 hours. With an observer on the ground, keeping well clear of the center joint area, perform the following test to check for looseness of center joint.

1. Have operator lift the attachment off the ground and then rapidly raise and lower the head several times to "bounce" machine.

2. As machine bounces, check for motion between the front and rear chassis frame lugs. Also check for a "clunking" sound at the center joint area.

726E-069

CHECK TRANSMISSION OIL LEVEL

CHECK OIL LEVEL Check oil level at end of every 8 hour shift.

Procedure: • Park on level ground, lower attachment to the ground, engage parking brake and turn off engine.

REAR CHASSIS FRONT CHASSIS

CHECK FOR MOVEMENT IN THIS JOINT AREA

724D-D11

•

Clean dirt and debris from around oil dipstick and check oil level.

•

If required, add the recommended grade of oil through the dipstick/fill tube.

Do not overfill.

1000 HOUR CHECK

3. Movement between front and rear chassis lugs or clunking of the pivot indicates a loose joint and preload must be checked.

Refer SECTION 11 of the SERVICE MANUAL for more information..

3.39

Tigercat 726E Feller Buncher

Lubrication and Maintenance

START-UP PROCEDURE AFTER MAJOR MACHINE MAINTENANCE This procedure should be followed: •

After major service or a rebuild.

•

Whenever the machine has been drained of hydraulic oil.

•

When any major component has been removed, repaired or replaced.

•

If the engine fuel supply has been disconnected or drained, refer to priming fuel system procedure in the engine manufacture's maintenance manual.

NOTE: Changing strainers, filters and replacing the hydraulic oil tends to aerate the oil. For maximum pump life, the machine should sit for 1 hour after servicing to allow entrained air to escape from the oil prior to applying working pressures to the pumps.

• Proceed to MACHINE START-UP procedure.

PRE-STARTUP AND FILLING 1. Check oil levels in the engine, the pump drive gearbox and the transmission.

2. Check coolant level in the radiator.

3. Do a final inspection of all fittings and clamps to make sure they are tight and will not leak.

4. Install the articulation lock bar and engage parking brake.

5. Do not start engine. Purge air from hydraulic system as follows: •

Ensure all filters are in place.

REMOVE PLUG

DRIVE PUMP

720E-012

•

Remove the plug on the top case port of the drive pump. This port will assist in venting air as hydraulic oil is filling the system components. Reinstall the plug when hydraulic oil free of air begins to flow out the port.

•

Fill the hydraulic tank if it has been drained.

•

Fill all the pumps and motors with prefiltered hydraulic oil through the highest case drain ports and close the ports.

NOTE: If the axles were drained of oil, refer to FILLING THE AXLES in this SECTION and in SECTION 8 of THE SERVICE MANUAL. 3.40

Tigercat 726E Feller Buncher

Lubrication and Maintenance

MACHINE START-UP Before beginning this procedure, perform the PRE START-UP AND FILLING steps.

NOTE: When the saw head is attached, retorque all teeth (See saw manual). Attach the SAW BLADE GUARD and insert the SAW BLADE LOCKING PIN.

5. Crank engine for 5 seconds, wait for 5 seconds. Check charge pressure gauge during cranking to observe for pressure reading. Repeat 5 times to pump oil into pumps and system components.

NOTE: If charge pressure gauge dose not indicate a rise in pressure, check for possible cause (air in system, leaks, loose hose fittings, pumps not turning, etc.). Repair problem.

Repeat step 5 until a rise in charge pressure is noticed.

1. Ensure the articulation lock bar is installed.

ENGINE "CPU" MODULE ELECTRO-INJECTOR MULTI-PIN CONNECTOR

CHASSIS MULTI-PIN CONNECTOR

SENSOR MULTI-PIN CONNECTOR

M726E-118

6. Reconnect engine CPU chassis multi-pin connector.

7. Turn key switch to RUN position and observe computer display. WAIT for the screen to display the gauges before starting the engine.

DISCONNECT CPU HARNESS

2. Disconnect the engine CPU chassis multi-pin connector (prevents engine starting).

INSTALL A 0 - 70 BAR (0-1000 PSI) GAUGE AT ‘M3’ PORT.

M726E-087

DRIVE PUMP

724E-047

DRIVE PUMP 'M3' TEST PORT CONNECTION

3. Install a 0-70 Bar (0-1000 psi.) gauge on drive pump to check charge pressure at ‘M3’ port.

Watch gauge closely.

8. Start engine. If charge pressure does not rise within 20 to 30 seconds, TURN ENGINE OFF. If charge pressure is between 18-31 Bar (260-450 psi.), run engine at IDLE for 20 minutes. Check engine oil pressure in cab. See COMPUTER, ENGINE MENU in SECTION 2 of the OPERATOR'S MANUAL Do not operate any functions.

9. With engine at IDLE, parking brake ON, hold foot brake down, bleed brakes in rear axle.

CAUTION Machine operator must ONLY take directions from the person doing the set-up.

4. Close cab doors, turn ignition key switch to the 'ON' position and depress the interlock reset switch. This will allow pilot oil to circulate and refill the pilot and case drain circuits during the following cranking procedure.

3.41

Tigercat 726E Feller Buncher

Lubrication and Maintenance

IMPORTANT!

Without a felling head attached, the tilt function can cause damage to the arms.

Watch the two LINK ARMS very carefully, as they may drop down beside the boom arms and wedge, causing the crank arms to bend.

When necessary, lower the boom DOWN, watching closely and tilt FORWARD, again watching the link arms closely.

CRANK ARM

HYDRAULIC OIL RESERVOIR

SIGHT GAUGE, HYDRAULIC OIL LEVEL

LINK ARM SENDING UNIT, HYDRAULIC OIL TEMPERATURE

HYDRAULIC OIL RESERVOIR 726E-079 14. With cylinders fully retracted, check hydraulic oil level.

OIL FILL ON/ OFF BUTTON BOOM ARM

718E-028

CRANK, LINK AND BOOM ARMS

FILL HOSE QUICK CONNECTION

10. Set throttle to IDLE and run each BOOM function for 2 minutes at LOW pressure to purge air from circuit.

NOTE: If the machine was on wheels, the steer and drive functions were not properly purged or flushed. Remove the articulation lock bar and at LOW IDLE, slowly operate the steer function right and left a few times. With the parking brake released and at LOW IDLE, slowly operate the drive function forward and reverse a few times.

11. Set throttle to FULL and run each function again for 2 minutes to flush circuit.

12. Set throttle to idle and shut engine off.

726E-079

ELECTRIC FILL PUMP

15. If required, top up the hydraulic oil reservoir with clean hydraulic oil using the electric fill pump. For operating instructions see SECTION 2 of the OPERATOR'S MANUAL. 16. Remove gauge from 'G' test port on drive pump. Clean up any spilled oil.

NOTE: If possible, allow the machine to stand for 4 to 6 hours before setting any of the operating pressures. This will allow any air bubbles in the oil to escape and is a good time to check for leaks.

17. Recheck hydraulic oil level and top up if required.

195-17

CHECK ENGINE COOLANT LEVEL

13. Top up the radiator with clean coolant.

18. Refer to appropriate section of the service manual to check and set operating pressures.

3.42

Tigercat 726E Feller Buncher REPLACING THE ENGINE SERPENTINE BELT

Lubrication and Maintenance PARKING BRAKE

1. Park the machine on level ground. Engage the parking brake, lower the attachment to the ground and shut engine off. Turn battery disconnect switch OFF.

PARKING BRAKE ASSEMBLY

A/C COMPRESSOR WATER PUMP PULLY SERPENTINE BELT

ALTERNATOR

BELT TENSIONER 470-05

SPRINGS

STATIONARY DISCS

DRIVE SHAFT

ROTATING DISCS

REMOVING SERPENTINE BELT

2. Install a Johnson bar with a 3/8" square drive in the square socket hole of the belt tensioner.

3. Loosen belt tensioner and remove the serpentine belt.

4. Replace the serpentine belt. Ensure that all of the ribs on the serpentine belt align with the grooves on the engine pulleys.

724E-007 724E-008 724E-112

PARKING BRAKE

The parking brake assembly is installed in the drive line between the transmission and the front axle. Five rotating discs are splined to the brake shaft and 6 stationary discs are held in place in the brake housing. The brake is spring applied and hydraulically released.

PARKING BRAKE SWITCH

M726E-044

CONTROL PANEL

A parking brake switch on the instrument panel activates and deactivates the brake, also the brake will be activated when the cab door is open or if the engine is not running. See also INSTRUMENT PANEL for more details regarding parking brake switch operation.

3.43

Tigercat 726E Feller Buncher

Lubrication and Maintenance

MIDDLE AND REAR DRIVE SHAFT SPLINE LUBRICATION When operating in extremely wet or dusty conditions or when the regular service schedule has been neglected, insufficient lubrication to the spline area of the middle drive shaft will result in premature wear. In addition old grease often forms into a semi-solid, rubber-like plug preventing the purging of contaminants (water, dirt, sand, etc.) through the slip spline seal.

1

The most common cause of joint and slip spline failure is lack of proper lubrication.

726M-012

REAR SLIP SPLINE

726E-002

REAR SLIP SPLINE LUBRICATION 4. Apply grease to grease nipple (1) until new, clean grease appears at the relief hole at yoke end of slip spline, FIG. 'C'.

5. Plug or cover relief hole and continue to apply pressure to grease nipple until new, clean grease appears at slip spline seal.

2

6. If grease does not appear at slip spline seal and continues to exit from the covered relief hole, remove the drive shaft and inspect for "hardened" grease build up, rust or other contaminants within the drive shaft. Repair or Replace drive shaft.

1

726M-008

MIDDLE SLIP SPLINE

MIDDLE SLIP SPLINE LUBRICATION 1. Park machine on level ground, and steer fully to the right. Lower attachment to the ground.

Set parking brake ON.

GREASE GUN

2. Stop the engine.

3. Apply grease to grease nipple (1) until new, clean grease exits from the relief fitting (2).

2

1 726M-011

Check to see if grease is exiting from the relief fitting (2). If grease does not exit from the relief fitting, remove the relief fitting and apply grease at the grease nipple. If grease flows out of relief fitting hole replace relief fitting.

If grease does not exit from the relief fitting hole, remove drive shaft and inspect for "hardened" grease build up, rust or other contaminants within the drive shaft. Repair or Replace drive shaft.

3.44

GREASE APPEARS AT RELIEF HOLE 720C-01

FIG. 'C' REAR DRIVE SHAFT YOKE END

Tigercat 726E Feller Buncher

Lubrication and Maintenance

Torque drive shaft yoke (universal Joint) fasteners to the following torque: • 6-C (3/8” - 24 UNF) 50 Nm (37 lbf-ft) lubricated NOTE: Yoke bolts on axles are metric threads. All other drive shaft bolts are imperial threads.

FRONT DRIVE SHAFT

REAR DRIVE SHAFT

MIDDLE DRIVE SHAFT

724E-112 726M-008 726E-001 726E-002

DRIVE SHAFT INSTALLATION 3.45

Tigercat 726E Feller Buncher

Lubrication and Maintenance

SPEED CONTROL LEVER ADJUSTMENT

SPEED CONTROL LEVER

PROTECTIVE RUBBER BOOT

ADJUSTABLE FRICTION SET SCREW

M726E-045

CONTROL PANEL

SPEED CONTROL LEVER

The friction setting on the speed control lever is variable and can be adjusted to allow proper operation.

The friction setting on the speed control lever may require adjustment, during normal operation, to maintain the set position of the lever, especially at maximum throw.

FRICTION SETTING PROCEDURE Before starting work, read and follow all servicing safety precautions in SECTION 1 of THIS MANUAL.

630B-31

1. Park machine on level ground, engage parking brake, lower attachment to ground, shut off engine.

2. Position the speed control lever in the neutral position (pointing straight up).

3. Raise the protective rubber ‘boot’ from the speed control valve body.

4. Locate the adjustable friction set screw.

5. Tighten the adjustable friction set screw as required (2.5mm hex key) 6. Replace the protective rubber ‘boot’ over the speed control valve body.

3.46

SPEED CONTROL LEVER FRICTION SET SCREW LOCATION

Tigercat 726E Feller Buncher FAN CONTROL ELECTRONIC CONTROLLER

Lubrication and Maintenance The temperature sensor in the hydraulic tank operates in a similar manner to the engine coolant temperature sensor but independently and with a different temperature range. This temperature range depends on the type of hydraulic oil used.

This sensor will signal the electronic control module to turn the fan ON at the minimum set point temperature. As the temperature of the hydraulic oil increases, the speed of the fan will also increase to a maximum 2200 rpm fan speed @1850 rpm engine speed, at this point the temperature of the hydraulic oil will be at the maximum set point or higher.

COOLING SET POINTS

M726E-078

Charge Air Min 60°C (140°F) Charge Air Max 82°C (180°F) Engine Coolant Min 84°C (183°F) Engine Coolant Max 95°C (203°F) Hydraulic Oil Temp values depend on type of oil used.

ELECTRONIC CONTROLLER

This control consists of an electronic processing module, a three position FAN switch in the operator's cab with CLEAN/AUTO/FULL ON* positions for fan control.

FAN SWITCH

When the switch is in the AUTO position and the fan is stopped due to low engine coolant, air intake or hydraulic oil temperatures, turning ON the A/C will immediately turn the cooling fan to run at 1200 rpm. This is to ensure that sufficient air flow is available for the cab A/C even while the machine is still warming up.

CAUTION M726E-044

Before placing the fan switch in the CLEAN (PURGE) position make sure that there are no personnel on the left side of the machine in the area where the fan will expel debris

CONTROL PANEL FULL ON AUTO CLEAN

M726E-131

When the engine coolant temperature reaches 84°C (183°F) the sensor on the engine in conjunction with the electronic control module will send a signal to the control valve to start to turn the fan slowly. The fan speed is variable from zero up to a maximum of 2200 rpm fan speed @1850 rpm engine speed. As the temperature of the coolant increases so does the speed of the fan up to the maximum 2200 rpm fan speed @1850 rpm engine speed. At this point the engine coolant temperature will be 95°C (203°F), or higher.

When the switch is in the FULL ON (OVERRIDE) position, the fan will run at FULL speed for cooling regardless of coolant, air intake or oil temperatures. The AUTO CLEAN/REVERSE feature will not function in the FULL ON position.

When the switch is pressed momentarily to the CLEAN (PURGE) position, the control module will signal the control valve to reverse the flow of oil to the motor and turn the fan in reverse. The control module will also turn the air conditioning system OFF for as long as the fan switch is in the CLEAN (PURGE) position.

See COMPUTER, GENERAL SETTING to make adjustments to FAN PURGE INTERVALS and FAN PURGE LENGTH in SECTION 2 of the operator's manual.

3.47

Tigercat 726E Feller Buncher

Lubrication and Maintenance

TORQUE CHART THREAD DIAMETER

LOCATION Cylinders Pin bolts Piston nut, steer cyl.

Piston nut, boom/tilt cyl.

Gland, steer cyl.

Keeper plate bolts

TORQUE (LUBRICATED) lbf-ft Nm

3/4" UNC 1 1/4" UNF 1 1/2" UNF 3/4" UNC

282-310 930 1640 450 282-310

393-420 1282 2260 620 389-420

1/2" UNC 3/4" UNC

80-88 282-310

109-119 393-420

Engine mounting Bolts, mount to chassis Bolts, front brackets to engine Bolts, rear brackets to engine Bolts, bracket to pump drive

7/8" UNC M10 x 1.5 (10.9) M12-1.75 (10.9) 5/8" UNC

364 32 75 159-175

500 43 100 216-237

Pump drive gearbox Drive plate to flywheel Bell housing to engine

M12-1.75 (10.9) M10 x 1.5 (10.9)

35-45 23-25

47-61 31-34

1 1/4" x 18 UNEF 3/4" UNC

475-525 357

644-711 484

1/2" UNF 1/2" UNF 3/8" UNF

120-132 120-132 37-49

163-179 163-179 50-66

Axle mounting bolts Front Rear

7/8" UNC 3/4" UNC

364 226

500 310

Wheel bolts

7/8" UNF

500-550

679-745

Transmission housing to frame

7/8" UNC

364

500

Center joint bearing Bearing retaining bolts Pin retaining bolts

Drive shafts Yoke retaining nut, front shaft Pillow block retaining bolts Universal joint bolts Rear & Mid. drive shaft Front drive shaft to Mid. drive shaft Front drive shaft to axle

Torque values pertaining to the engine and attachment are provided in the appropriate manuals.

M726E-TORQUECHART.XLS

3.48

Tigercat 726E Feller Buncher

Lubrication and Maintenance

GENERAL TORQUE SPECIFICATIONS

The torque values listed below are for general use only.

DO NOT use these values if a different torque value or tightening procedure is shown for a specific application.

IMPERIAL

GRADE 5 BOLTS

GRADE 8 BOLTS

IMPERIAL BOLT TORQUE SPECIFICATIONS GRADE 5 BOLTS GRADE 8 BOLTS LUBRICATED lbf-ft Nm 8 - 10 11 - 13 20 - 28 27 - 38 33 - 36 45 - 49 52 - 57 71 - 77 80 - 88 109 - 119 115 - 127 156 - 172 159 - 175 216 - 237 282 - 310 393 - 420 455 - 501 617 - 679 682 - 750 925 - 1016 966 - 1062 1310 - 1441 1360 - 1496 1844 - 2027 LUBRICATED lbf-ft Nm 10 - 13 14 - 17 18 - 25 25 - 33 37 - 41 50 - 55 58 - 64 79 - 86 90 - 99 122 - 134 128 - 141 174 - 191 180 - 198 244 - 268 315 - 347 427 - 470 501 - 550 679 - 745 746 - 821 1012 - 1113 1083 - 1191 1469 - 1613 1509 - 1660 2046 - 2250 4.8

METRIC

DRY LUBRICATED COARSE lbf-ft Nm lbf-ft Nm THREAD 1/4" - 20 7- 8 10 - 11 8 - 10 11 - 13 5/16" - 18 14 - 18 19 - 24 10 - 15 13 - 20 3/8" - 16 31 - 34 42 - 46 23 - 25 31 - 34 7/16" - 14 49 - 54 66 - 73 37 - 41 50 - 55 1/2" - 13 75 - 83 102 - 112 57 - 63 77 - 85 9/16" - 12 109 - 120 148 - 162 82 - 90 111 - 122 5/8" - 11 150 - 165 204 - 223 113 - 124 152 - 168 3/4" - 10 266 - 293 360 - 397 200 - 220 271 - 298 7/8" - 9 394 - 433 535 - 586 296 - 326 402 - 441 1" - 8 591 - 649 802 - 879 443 - 489 601 - 663 1 1/8" - 7 794 - 873 1077 - 1183 596 - 656 808 - 889 1 1/4" - 7 1120 - 1232 1519 - 1670 840 - 924 1139 - 1252 FINE DRY LUBRICATED lbf-ft Nm lbf-ft Nm THREAD 1/4" - 28 9 - 10 12 - 13 9 - 10 12 - 13 5/16" - 24 17 - 22 23 - 29 16 - 20 21 - 27 3/8" - 24 35 - 39 48 - 53 26 - 29 35 - 39 7/16" - 20 55 - 61 75 - 83 41 - 45 56 - 61 1/2" - 20 85 - 94 116 - 127 64 - 70 87 - 95 9/16" - 18 121 - 133 164 - 180 91 - 100 124 - 135 5/8" - 18 170 - 187 231 - 253 128 - 141 174 - 191 3/4" - 16 297 - 327 403 - 443 223 - 245 303 - 332 7/8" - 14 434 - 477 589 - 646 326 - 359 442 - 486 1" - 12 646 - 711 876 - 965 484 - 534 657 - 724 1 1/8" - 12 891 - 980 1208 - 1328 668 - 735 906 - 996 1 1/4" - 12 1240 - 1364 1682 - 1849 931 - 1024 1262 - 1387

8.8

9.8

10.9

4.8

8.8

9.8

10.9

12.9

4.8

8.8

9.8

10.9

12.9

10

5 5

SIZE

CLASS 4.8 LUBRICATED DRY Nm lbf-ft Nm lbf-ft

10

10

5

12.9

10

12.9

12

10

12

METRIC BOLT TORQUE SPECIFICATIONS

CLASS 8.8 OR 9.9 LUBRICATED DRY Nm lbf-ft Nm lbf-ft

12.9

12

DRY lbf-ft Nm 11 - 12 15 - 16 26 - 30 35 - 40 44 -48 60 - 65 70 - 77 95 - 104 106 - 117 144 - 158 153 - 168 208 - 228 212 - 233 288 - 316 376 - 414 510 - 561 606 - 667 822 - 904 909 - 1000 1233 - 1355 1288 - 1417 1746 - 1921 1817 - 1999 2464 - 2710 DRY lbf-ft Nm 13 - 14 18 - 19 23 - 28 31 - 38 49 - 54 67 - 73 78 - 86 106 - 116 120 - 132 163 - 179 171 - 188 232 - 255 240 - 264 326 - 358 420 - 462 570 - 626 668 - 735 906 - 996 995 - 1096 1359 - 1486 1445 - 1590 1960 - 2155 2012 - 2213 2728 - 2997

10

COARSE THREAD 1/4" - 20 5/16" - 18 3/8" - 16 7/16" - 14 1/2" - 13 9/16" - 12 5/8" - 11 3/4" - 10 7/8" - 9 1" - 8 1 1/8" - 7 1 1/4" - 7 FINE THREAD 1/4" - 28 5/16" - 24 3/8" - 24 7/16" - 20 1/2" - 20 9/16" - 18 5/8" - 18 3/4" - 16 7/8" - 14 1" - 14 1 1/8" - 12 1 1/4" - 12

CLASS 10.9 LUBRICATED DRY Nm lbf-ft Nm lbf-ft

CLASS 12.9 LUBRICATED DRY Nm lbf-ft Nm lbf-ft

M6 M8 M10

4.8 12.0 23.0

3.5 8.5 17.0

6.0 15.0 29.0

4.5 11.0 21.0

9.0 22.0 43.0

6.5 16.0 32.0

11.0 28.0 55.0

8.5 20.0 40.0

13.0 32.0 63.0

9.5 24.0 47.0

17.0 40.0 80.0

12.0 30.0 60.0

15.0 37.0 75.0

11.5 28.0 55.0

19.0 47.0 95.0

14.5 35.0 70.0

M12 M14 M16

40.0 63.0 100.0

29.0 47.0 73.0

50.0 80.0 125.0

37.0 60.0 92.0

75.0 120.0 190.0

55.0 88.0 140.0

95.0 150.0 240.0

70.0 110.0 175.0

110.0 175.0 275.0

80.0 130.0 200.0

140.0 225.0 350.0

105.0 165.0 225.0

130.0 205.0 320.0

95.0 150.0 240.0

165.0 260.0 400.0

120.0 190.0 300.0

M18 M20 M22

135.0 190.0 260.0

100.0 140.0 190.0

175.0 240.0 330.0

125.0 180.0 250.0

260.0 375.0 510.0

195.0 275.0 375.0

330.0 475.0 650.0

250.0 350.0 475.0

375.0 530.0 725.0

275.0 400.0 540.0

475.0 675.0 925.0

350.0 500.0 675.0

440.0 625.0 850.0

325.0 560.0 460.0 800.0 625.0 1,075.0

410.0 580.0 800.0

M24 M27 M30

330.0 490.0 675.0

250.0 360.0 490.0

425.0 625.0 850.0

310.0 650.0 450.0 950.0 625.0 1,300.0

M33 900.0 M36 1,150.0

475.0 825.0 600.0 925.0 675.0 1,150.0 850.0 1,075.0 800.0 1,350.0 1,000.0 700.0 1,200.0 875.0 1,350.0 1,000.0 1,700.0 1,250.0 1,600.0 1,150.0 2,000.0 1,500.0 950.0 1,650.0 1,200.0 1,850.0 1,350.0 2,300.0 1,700.0 2,150.0 1,600.0 2,700.0 2,000.0

675.0 1,150.0 850.0 1,750.0 1,300.0 2,200.0 1,650.0 2,500.0 1,850.0 3,150.0 2,350.0 2,900.0 2,150.0 3,700.0 2,750.0 850.0 1,450.0 1,075.0 2,250.0 1,650.0 2,850.0 2,100.0 3,200.0 2,350.0 4,050.0 3,000.0 3,750.0 2,750.0 4,750.0 3,500.0

TORQUECHARTGENERAL.XLS

3.49

Tigercat 726E Feller Buncher

Lubrication and Maintenance

PRESSURE SETTINGS 726E

With hydraulic oil at operating temperature 49°C - 60°C (120°F - 140°F) Location Engine RPM

BAR

PSI

Engine RPM 1800 ± 25 High Idle 850 ± 25 Low Idle

Pilot Manifold Pressure Relief Valve Pressure Reducing Valve

46.5 38

675 550

850 850

Pressure

Drive Pump - Dual Motor One Speed Charge Pressure Relief Valve Multi Function Valve: · P.O.R. Forward · P.O.R. Reverse · High Pressure Relief Forward Non-Adjustable · High Pressure Relief Reverse Non-Adjustable

29.3

425

1800

348.2 348.2 348.2 348.2

5050 5050 5500 5500

2200 2200

Drive Motor - Dual Motor One Speed Drive Motor P.O.R. Loop flushing Pressure Relief Non-Adjustable

279.2 24.8

4050 360

2200

Steer Valve (Joystick Steering Only Steer Valve Main Relief Steer Right Port Relief Steer Left Port Relief

172.4 221 221

2500 3200 3200

1800 850 850

Saw Saw Valve Main Relief Saw Motor P.O.R. Saw Pump P.O.R. Standby Pressure

276 221 248 16-19

4000 @ 1100 rpm 3200 @ 2200 rpm 3600 @ 2200 rpm 225-300 @ 2200 rpm

Boom Valve Mid Inlet Main Relief or Main Relief Tilt In Port Relief Tilt Out Port Relief Accumulator Clamp Open Port Relief Accumulator Clamp Close Port Relief Clamp Open Port Relief Clamp Close Port Relief Boom Lift Port Relief Boom Lower Port Relief

179.3 200 200 221 221 76 221 200 152

2600 2900 2900 3200 3200 1100 3200 2900 2200

IMPORTANT NOTES: ~ Boom support must be used part# 4128A ~ When performing tilt out function, without a felling head installed, do not allow crank arms to hit boom

M726E PRESSURE SETTINGS

3.50

1800 850 850 850 850 850 850 850 850

Tigercat 726E Feller Buncher

Lubrication and Maintenance

EATON Aeroquip

Assembly Torque

Recommended Parallel Connection Assembly torque

Eaton recommends that a Torque wrench be used to assure proper fitting assembly of these connections.

Straight Thread O-Ring Boss Low Pressure with 37º (SAEJ514)

Straight Thread O-Ring Boss High Pressure with ORS (J1453)

Thread Size (inches) 3/8-24 7/16-20 1/2-20 9/16-18 3/4-16 7/8-14 1 1/16-12 1 3/16-12 1 5/16-12 1 5/8-12 1 7/8-12 2 1/2-12

Dash Size -03 -04 -05 -06 -08 -10 -12 -14 -16 -20 -24 -32

The values listed are for steel connections. Contact Teaton for torque values for other materials.

Jam Nut or Jam Nut or Straight Straight Fitting Torque Fitting Torque lb.-ft.

Newton Meters 8-9 12-13 13-15 18-20 14-15 19-21 23-24 32-33 40-43 55-57 43-48 59-64 68-75 93-101 83-90 113-122 112-123 152-166 146-161 198-218 154-170 209-230 218-240 296-325

Dash Size -03 -04 -05 -06 -08 -10 -12 -14 -16 -20 -24

ORS

Dash Size -04 -06 -08 -10 -12 -16 -20 -24

Thread Size (inches) 3/8-24 7/16-20 1/2-20 9/16-18 3/4-16 7/8-14 1 1/16-12 1 3/16-12 1 5/16-12 1 5/8-12 1 7/8-12

Jam Nut or Jam Nut or Straight Straight Fitting Torque Fitting Torque lb.-ft.

Newton Meters 8-10 11-16 14-16 20-22 18-20 24-27 24-26 33-35 50-60 68-78 72-80 98-110 125-135 170-183 160-180 215-245 200-220 270-300 210-280 285-380 270-360 370-490

SAE 37º (JIC) Thread Size (inches) 9/16-18 11/16-20 13/16-16 1-14 1 3/16-12 1 7/16-12 1 11/16-12 2-12

Swivel Nut Torque lb.-ft.

10-12 18-20 32-35 46-50 65-70 92-100 125-140 150-165

Swivel Nut Torque Newton Meters 14-16 24-27 43-47 62-68 88-95 125-136 170-190 204-224

Dash Size -04 -05 -06 -08 -10 -12 -16 -20 -24 -32

Metric Thread Size mm M10x1 M12x1.5 M14x1.5 M16x1.5 M18x1.5 M20x1.5 M22x1.5 M26x1.5 M27x2 M33x2 M42x2 M48x2

Thread Size (inches) 7/16-20 1/2-20 9/16-18 3/4-16 7/8-14 1 1/16-12 1 5/16-12 1 5/8-12 1 7/8-12 2 1/2-12

Swivel Nut Torque lb.-ft.

11-12 15-16 18-20 38-42 57-62 79-87 108-113 127-133 158-167 245-258

Swivel Nut Torque Newton Meters 15-16 20-22 24-28 52-58 77-85 108-119 148-154 173-182 216-227 334-352

BSPP Straight Adapter or Locknut Torque lb.-ft.

Newton Meters 13-15 18-20 15-19 20-25 19-23 25-30 33-40 45-55 37-44 50-60 52-66 70-90 55-70 75-95 81-96 110-130 96-111 130-150 162-184 220-250 170-192 230-260 258-347 350-470

Nominal Thread Size Straight Adapter or Locknut Torque inches** lb.-ft.

Newton Meters G1/8-28 13-15 18-20 G1/4-19 19-23 25-30 G3/8-19 33-40 45-55 G1/2-14 55-70 75-95 G3/4-14 103-118 140-160 G1-11 162-184 220-250 G1 1/4-11 170-192 230-260 G1 1/2-11 258-347 350-470 ** "G" denotes parallel threads, other than ISO 6149 (Port connection only)

Eaton Aeroquip Fluid Conveyance Products A-HOOV-MC001-E January 2005

3.51

Tigercat 726E Feller Buncher

Lubrication and Maintenance

Parker

Assembly Torque The four-bolt port is simply a circular opening (flow passage) surrounded by four tapped holes in a certain pattern for acceptance of the flange clamping bolts. The flat surface of the port compresses the O-ring contained in the groove in the flange head when the clamp bolts are torqued. In some instances, the groove is in the port and not in the flange head. The bolts, through the clamp halves, clamp down the flange head on to the flat surface of the port compressing and trapping the O-ring in the groove and leaving no gap for it to extrude under pressure. The hydraulic pressure is thus sealed by the compressed O-ring as long as the bolts are tightened enough to maintain solid metal to metal contact between the flange head at the outside diameter of the O-ring and the top of the port.

The 4-Bolt Split Flange consists of four main components: • A body (flange head) • An O-ring • One “captive” or two “split” flange clamps

• Four bolts and washer

WASHERS BOLTS FLANGE CLAMP

Flange Port Assembly

FLANGE HEAD

The steps to properly assemble the flange port clamping bolts are: 1. Make sure sealing surfaces are free of burrs, nicks, scratches or any foreign particles.

2. Lubricate the O-ring.

3. Position flange and clamp halves.

4. Place lock washers on bolts and insert through clamp halves.

5. Hand tighten bolts.

6. Torque bolts in diagonal sequence (see Fig. T9) in small increments to the appropriate torque level listed in Table T6 or Table T7 on this page.

O-RING TAPPED HOLES

FLANGE.JPG

Fig. T8 - 4 Bolt Split Flange Components

FLANGE2.JPG

Fig. T9 - Flange Bolt Tightening Sequence

Dash Size

Flange Size

Inch Bolt (J518)

Torque lbf-ft

Metric Bolt (ISO 6162)

Torque N-m

Dash Size

Flange Size

Inch Bolt (J518)

Torque lbf-ft

Metric Bolt (ISO 6162)

Torque N-m

8 12 16 20 24 32 40 48 56 64 80

1/2 3/4 1 1-1/4 1-1/2 2 2-1/2 3 3-1/2 4 5

5/16-18 3/8-16 3/8-16 7/16-14 1/2-13 1/2-13 1/2-13 5/8-11 5/8-11 5/8-11 5/8-11

17 +/- 2 25 +/- 3.5 31 +/- 4.5 41 +/- 5 52 +/- 6 60 +/- 6 85 +/- 9 144 +/- 15 125 +/- 8 125 +/- 8 125 +/- 8

M8 M10 M10 M12 M12 M12 M12 M16 M16 M16 M16

25 49 49 85 85 135 95 220 220 220 220

8 12 16 20 24 32

1/2 3/4 1 1 1/4 1 1/2 2

5/16-18 3/8-16 7/16-14 1/2-13 5/8-11 3/4-10

17 +/- 2 30 +/- 4.5 46 +/- 4.5 69 +/- 6 125 +/- 8 208 +/- 20

M8 M10 M12 M14 M16 M20

25 49 85 135 210 425

* Does not meet ISO 6162 specification.

Table T7 - Code 62 Flange Recommended Bolt Torque

* Does not meet ISO 6162 specification.

Table T6 - Code 61 Flange Recommended Bolt Torque

3.52

Tigercat 726E Feller Buncher

Lubrication and Maintenance

Parker

Assembly Torque

JIC 37 Degree Flare SAE Dash Size

Thread Size

-2 -3 -4 -5 -6 -8 -10 -12 -14 -16 -20 -24 -32 -40

NPTF

Tube Connection Swivel or Hose Connection FFWR FFWR

5/16-24 3/8-24 7/16-20 1/2-20 9/16-18 3/4-16 7/8-14 1 1/16-12 1 3/16-12 1 5/16-12 1 5/8-12 1 7/8-12 2 1/2-12 3-12

NA NA 2 2 1 1/2 1 1/2 1 1/2 1 1/4 1 1 1 1 1 1

SAE Dash Size

NA NA 2 2 1 1/4 1 1 1 1 1 1 1 1 1

-2 -3 -4 -5 -6 -8 -10 -12 -14 -16 -20 -24 -32 -40

F.F.W.R : Flats From Wrench Resistance All values are for Steel, Stainless Steel and Brass

1/8-27 NA 1/4-18 NA 3/8-18 1/2-14 7/8-14 3/4-14 NA 1-11 1/2 1 1/4-11 1/2 1 1/2-11 1/2 2-11 1/2 NA

Thread Size

-2 -3 -4 -5 -6 -8 -10 -12 -14 -16 -20 -24 -32 -40

NA NA 1/4 TO 1/2 NA 1/4 TO 1/2 1/4 TO 1/2 1/4 TO 1/2 1/4 TO 1/2 NA 1/4 TO 1/2 1/4 TO 1/2 1/4 TO 1/2 NA NA

2-3 NA 2-3 NA 2-3 2-3 NA 2-3 NA 1.5-2.5 1.5-2.5 1.5-2.5 1.5-2.5 NA

BSPT

Tube Connection Swivel or Hose Connection FFWR FFWR

NA NA 9/16-18 NA 11/16-16 13/16-16 1-14 1 3/16-12 NA 1 7/16-12 1 11/16-12 2-12 NA NA

2-3 NA 2-3 NA 2-3 2-3 NA 2-3 NA 1.5-2.5 1.5-2.5 1.5-2.5 1.5-2.5 NA

T.F.F.T. : Turns from finger tight All pipe values are for Steel, Stainless Steel and Brass

O'ring Face Seal / Seal-Lok SAE Dash Size

Tube Connection Swivel or Hose Connection TFFT TFFT

Thread Size

SAE Dash Size

NA NA 1/2 TO 3/4 NA 1/2 TO 3/4 1/2 TO 3/4 1/2 TO 3/4 1/3 TO 1/2 NA 1/3 TO 1/2 1/3 TO 1/2 1/3 TO 1/2 NA NA

-2 -3 -4 -5 -6 -8 -10 -12 -14 -16 -20 -24 -32 -40

F.F.W.R : Flats From Wrench Resistance All values are for Steel, Stainless Steel and Brass

Thread Size

Tube Connection Swivel or Hose Connection TFFT TFFT

1/8-28 NA 1/4-19 NA 3/8-19 1/2-14 NA 3/4-14 NA 1-11 1 1/4-11 1 1/2-11 2-11 NA

2-3 NA 2-3 NA 2-3 2-3 NA 2-3 NA 1.5-2.5 1.5-2.5 1.5-2.5 1.5-2.5 NA

2-3 NA 2-3 NA 2-3 2-3 NA 2-3 NA 1.5-2.5 1.5-2.5 1.5-2.5 1.5-2.5 NA

T.F.F.T. : Turns from finger tight All pipe values are for Steel, Stainless Steel and Brass

SAE J1926 Straight Thread Port Assembly Torques ASSEMBLY TORQUE = 10 % -0 SAE DASH SIZE

2 3 4 5 6 8 10 12 14 16 20 24 32

THREAD SIZE

5/16-24 3/8-24 7/16-20 1/2-20 9/16-18 3/4-16 7/8-14 1 1/16-12 1 3/16-12 1 5/16-12 1 5/8-12 1 7/8-12 2 1/2-12

SEAL-LOK lbf•ft (lbf•in) (310) (310) (310) (360) (420) 60 100 135 175 200 250 305 375

N •m 20 20 20 40 46 80 135 185 235 270 340 415 510

TRIPLE-LOK FERULOK PIPE FITTINGS lbf•ft N •m (lbf•in) (85) 10 (155) 18 (260) 29 (280) 32 (350) 40 (620) 70 85 115 135 183 175 237 200 271 250 339 305 414 375 509

PLUGS

ADJUSTABLE

NON-ADJUSTABLE

SEAL-LOK lbf•ft (lbf•in) (310) (310) (310) (360) (420) 60 100 135 175 200 250 305 375

3.53

N •m 20 20 20 40 46 80 135 185 235 270 340 415 510

TRIPLE-LOK FERULOK PIPE FITTINGS lbf•ft N •m (lbf•in) (60) 7 (100) 11 (180) 20 (250) 28 (350) 40 (620) 70 85 115 135 183 175 237 200 271 250 339 305 414 375 509

HOLLOW HEX HP5ON-S lbf•ft (lbf•in) (30) (55) (120) (170) (410) 60 100 135 175 200 250 305 375

N •m 3.5 6 13.5 19 46 80 135 185 235 270 340 415 510

HEX HEAD P5ON-S lbf•ft (lbf•in) (85) (155) (260) (280) (350) (620) 85 135 175 200 250 305 375

N •m 10 18 29 32 40 70 115 183 237 271 339 414 509

Tigercat 726E Feller Buncher

Lubrication and Maintenance

Weights of Commercial Wood

Species

kg/m3

lb/ft3

Species

kg/m3

lb/ft3

Alder, Red Ash, White Aspen, Quaking Bald Cypress Basswood, American Beech, American Birch, Paper Birch, Yellow Cedar, Alaska Cedar, Incense Cedar, Northern White Cedar, Port-Orford Cedar, Western Red Cherry, Black Cottonwood, Eastern Douglas Fir, Coast Douglas Fir, Inland North Elm, American Fir, Alpine Fir, Balsam Fir, Nobel Fir, Red Fir, Silver Fir, White Gum, Black Gum, Blue Gum, Red Gum, Tupelo Hemlock, Eastern Hemlock, Western Hickory, Pecan Hickory, True Larch, Western Locust, Black Magnolia, Cucumber

737 769 689 817 673 865 801 929 577 721 449 897 433 721 785 881 577 865 449 721 481 769 577 753 721 1121 801 897 801 657 993 1009 769 929 785

46 48 43 51 42 54 50 58 36 45 28 56 27 45 49 55 36 54 28 45 30 48 36 47 45 70 50 56 50 41 62 63 48 58 49

Maple, Big Leaf Maple, Black Maple, Red Maple, Silver Maple, Sugar Oak, Black Oak, Chestnut Oak, Red Oak, Red, Swamp Oak, Swamp Chestnut Oak, White Oak, White, Swamp Pine, Jack Pine, Loblolly Pine, Lodgepole Pine, Long Leaf Pine, Norway, Red Pine, Short Leaf Pine, Slash Pine, Sugar Pine, Western Yellow Pine, White-Western Pine, White-Eastern Poplar, Yellow Redwood Spruce, Black Spruce, Engleman Spruce, Red Spruce, Sitka Spruce, White Sweetgum Sycamore, American Tamarack Walnut, Black Willow, Black

753 865 801 721 897 1009 977 1009 1073 1041 993 1105 801 993 625 993 673 993 993 817 721 561 577 609 801 513 625 545 529 545 801 833 753 929 801

47 54 50 45 56 63 61 63 67 65 62 69 50 62 39 62 42 62 62 51 45 35 36 38 50 32 39 34 33 34 50 52 47 58 50

Note: The values shown here are green weights.

3.54

Tigercat 726E Feller Buncher

Lubrication and Maintenance

Tigercat wire colour code chart applicable to all products manufactured by Tigercat Industries Inc. COLOUR FUNCTION EXAMPLE Red Power..........................................(fused and unfused) Black Ground White Engine control.............................(fuel shut-off, start aid) Blue Propulsion Control......................(transmission/reverser solenoids) Purple Monitor, electrical and

mechanical systems....................(air cleaner, alternator, wheel speed, engine speed) Tan Electrical and

electromechanical control...........(park brake, alternator excitation)

(power door motor, backup alarm) Yellow Monitors......................................(flow, pressure, temperature, level) Grey Standard monitor system............(logic module to monitor) Brown Lights Green Electro-hydraulic control.............(pilot solenoids) Orange Accessories.................................(horn, A/C, heater)

COMMON CONVERSIONS To Convert Bar cc °C Kg KW Liters mm Nm N

Into PSI Cu. in. °F lbs.

HP Gallons Inches lb.-ft. lbs.

To Convert

Multiply By

Cu. in. °F Gallons HP Inches lbs. lb.-ft.

PSI In. of HG In. of H2O lbs.

14.5 0.06102 (°C x 9/5) + 32 2.205 1.341 0.2642 0.03937 0.7375 0.22481

3.55

Into

cc °C Liters KW mm Kg Nm Bar PSI PSI N

Multiply By

16.39 (°F - 32) /1.8 3.785 0.7457 25.4 0.4535 1.356 0.06896 . 4912 . 03613 4.4482

Tigercat 726E Feller Buncher

Lubrication and Maintenance

3.56