Tigercat 610E 615E Skidder Operator's Manual - PDF DOWNLOAD

610E/615E SKIDDER

OPERATOR’S MANUAL SERIAL NUMBER 6101101 TO 6102500 SERIAL NUMBER 6151001 TO 6151500

ISSUE 2.0 MARCH 2015 Tigercat Industries Inc. P.O. Box 637 Brantford, Ontario Canada N3T 5P9 Tel: (519) 753-2000 Fax: (519) 753-8272

Introduction

Tigercat 610E/615E Skidder

ii

Tigercat 610E/615E Skidder

Introduction

Tigercat 610E/615E SKIDDER TABLE OF CONTENTS

SECTION INTRODUCTION.....................................................................................................................................v S.A.E. STANDARDS..............................................................................................................................vi NON-APPROVED FIELD PRODUCT CHANGES................................................................................. vii SAFETY...................................................................................................................................................1 CONTROLS AND OPERATION..............................................................................................................2 LUBRICATION AND MAINTENANCE.....................................................................................................3

CALIFORNIA Proposition 65 Warning Diesel engine exhaust and some of its constituents are known to the State of California to cause cancer, birth defects and other reproductive harm.

610E/615E Available Literature Operator’s Manual (This Manual).........................................................Part No. 44476AENG Service Manual .....................................................................................Part No. 44477AENG 610E Parts Catalog...............................................................................Part No. 44475A 615E Parts Catalog...............................................................................Part No. 45763A Vehicle Moving and Transporting Instructions.......................................Part No. 41604AMUL

iii

Introduction

Tigercat 610E/615E Skidder

iv

Tigercat 610E/615E Skidder

Introduction

Tigercat 610E/615E Skidder INTRODUCTION An Operator's manual, Service manual and a Parts catalog are provided by Tigercat to assist the dealer, customer and operator in becoming familiar with the features of the 610E/615E Skidder.

Serial numbers:610E 615E

6101101 to 6102500 6151001 to 6151500

The 610E/615E Skidder is designed for skidding trees in selective felling and clear felling applications in plantations and natural stands.

The operator's manual will assist the operator with the techniques of proper and safe operation of the 610E/615E Skidder. The service manual contains safety and servicing procedures and a preventive maintenance schedule to assist in repair and to ensure optimum machine performance. For manual part numbers, see the title page in each manual.

Section 1 in both the operator's manual and the service manual contains safety information that must be followed. As well, throughout the rest of the manuals WARNING and CAUTION notices are displayed where necessary, drawing attention to possible hazards when performing certain procedures.

Only trained personnel should be allowed to operate or work on the machine.

The information contained in this manual is current at time of printing. Improvements to the machine are on-going and may not be covered, therefore in these cases contact your Tigercat dealer for the appropriate information.

The phrase "and up" appearing in this manual after the serial number implies that the related information is current for any machine serial number HIGHER than the serial number preceding the "and up".

Tigercat reserves the right to make changes to the machine after this manual release date that may not immediately appear in this manual.

Every effort is made to send out updates on a regular basis. If the machine in question was built after the release date of this manual and there is a discrepancy, call Tigercat service department. The release date appears on the first page.

The Company reserves the right to change information contained herein at any time without prior notice.

Tigercat Industries Inc.

v

Introduction

Tigercat 610E/615E Skidder

S.A.E. STANDARDS ROLL-OVER PROTECTION STRUCTURES (ROPS) FALLING OBJECTS PROTECTION STRUCTURES (FOPS) OPERATOR PROTECTION STRUCTURES (OPS) * MODIFICATIONS AND REPAIRS:

The integrity of the ROPS, FOPS, OPS structure and its continued ability to provide the level of protection it was designed for could be seriously affected by any modifications to the structure, its mounting or to the chassis to which it is attached.

Tigercat emphasizes that the certification of approval of the ROPS, FOPS, OPS structure will become void if any such modifications take place.

Tigercat may officially grant approval for modifications only by: i)

Written approval of repairs or modifications signed by the Tigercat Engineering Manager; or

ii) Approved modifications officially released by Tigercat.

Both of the above are provided that the work is carried out in the factory approved manner.

Unauthorized modifications and/or repairs made or contributed to by a customer or a Tigercat distributor may result in creating a dangerous situation and therefore the customer or Tigercat distributor will be considered to have assumed the risk involved or be negligent in creating this situation.

Tigercat will not be held responsible for situations arising from having created unauthorized modifications/ changes to the structure.

Operator's cabs are designed to ROPS, FOPS, OPS standards so that they will withstand force and absorb energy during a roll-over (ROPS), when resisting the impact of a falling object (FOPS) and minimize the possibility of operator injury from penetrating objects (OPS). When a permanent deflection of the structure occurs, the structure can no longer provide the original designed level of protection and should be replaced. Attempts to straighten the structure, particularly by the application of heat, can reduce still further the structures remaining capability to protect.

The mounting and the frame or chassis to which the cab is attached is considered an integral part of the ROPS, FOPS, OPS and is included in the design, test and certification of the product.

Contact the Tigercat Service department before attempting any modifications or repair to roll-over protective structures.

PROTECTIVE STRUCTURES CERTIFICATION

Tigercat Industries Inc.

FOR USE ON ALL Tigercat 600 SERIES MACHINES THIS OPERATOR ENCLOSURE MEETS THE FOLLOWING PROTECTIVE STRUCTURE STANDARDS: ISO 8082:2003 (Roll Over) Maximum Machine Mass 23 360kg / 51,500lb ISO 8083:2006 (Falling Object) Drop Energy Level: 11,600J ISO 8084:2003 (Operator) TO MAINTAIN OPERATOR PROTECTION AND PROTECTIVE STRUCTURES CERTIFICATION • All damaged protective structures must be replaced, not repaired.

• Any alterations must be approved by manufacturer.

MANUFACTURED BY

Tigercat Industries Inc. Brantford, Ontario, Canada 30590AUNI R1

vi

Tigercat 610E/615E Skidder

Introduction

NON-APPROVED FIELD PRODUCT CHANGES The installation of any unauthorized attachment or changes made of any kind to this Tigercat product could affect the product's ability to perform as originally intended. The product's integrity, stability and safety could be at serious risk.

IT IS Tigercat POLICY THAT NO CHANGES ARE TO BE MADE TO ITS PRODUCTS INCLUDING DELETIONS OR ADDITIONS OTHER THAN A Tigercat APPROVED OPTION FITTED IN THE FACTORY APPROVED MANNER. Official approval to make changes or install options is only as follows: i)

The relevant options for that product must be shown or listed on current Tigercat documentation or literature such as a printed specification sheet, price list, parts manual, or product literature issued by Tigercat.

ii) Approved options or product changes authorized in writing by the Tigercat Engineering Manager.

Authorization by any other person is unacceptable.

Unauthorized changes made or contributed to by a person or organization may result in creating a dangerous situation and therefore the person or organization will be considered to have assumed the risk involved or be negligent in creating this situation.

Weight is an important factor when considering the addition of options or an attachment, Refer to your Tigercat distributor for information on maximum permissible operating weight and the effect the addition of various options may have on your machine.

Tigercat will not be held responsible for any situation that may arise resulting from Non-approved Field Product Changes to its product.

Should Tigercat become involved in a suit resulting from changes made to the product without proper authorization by Tigercat as stated above, Tigercat will take whatever action is appropriate to protect its interests.

The product warranty policy and the certification on any safety items installed on the modified product will become NULL and VOID if the above policy is not adhered to as specified.

Non-approved product changes also nullify warranties given to Tigercat by its component manufacturers.

Tigercat Industries Inc.

vii

Introduction

Tigercat 610E/615E Skidder

viii

Tigercat 610E/615E Skidder SECTION 1 - SAFETY Read and understand this Safety section prior to operating any equipment.

Read and understand all manuals for any attachments or accessories.

CONTENTS - SECTION 1

ISSUE 2.0 MARCH 2015

ARTICULATION LOCK............................................................................................................................. 1.30 BATTERY DISCONNECT SWITCH......................................................................................................... 1.10 BATTERY SAFETY.................................................................................................................................... 1.8 CAB EXITS.................................................................................................................................................1.9 CAB SAFETY CABLE.............................................................................................................................. 1.15 CAB SUPPORT BRACE.......................................................................................................................... 1.15 COOLING SYSTEM................................................................................................................................. 1.14 DIESEL EXHAUST FLUID (DEF)............................................................................................................... 1.9 EMERGENCY CAB EXITS......................................................................................................................... 1.9 EXHAUST FUMES................................................................................................................................... 1.16 FIRE PREVENTION................................................................................................................................. 1.22 DRY CHEMICAL CLEANUP PROCEDURES....................................................................................... 1.26 FIRE PREVENTION GUIDELINES....................................................................................................... 1.22 WHAT TO DO AFTER A MACHINE FIRE HAS OCCURRED............................................................... 1.25 WHAT TO DO TO PREPARE FOR A MACHINE FIRE......................................................................... 1.23 WHAT TO DO WHEN A MACHINE FIRE OCCURS............................................................................. 1.24 FIRST AID..................................................................................................................................................1.6 FLUID INJECTION INJURY..................................................................................................................... 1.17 FLUID LEAKS..........................................................................................................................................1.14 GREASE INJECTION INJURY................................................................................................................. 1.18 HYDRAULIC PRESSURE HAZARD........................................................................................................ 1.14 LIGHTNING SAFETY AWARENESS....................................................................................................... 1.19 LOOSE CLOTHING HAZARD.................................................................................................................. 1.14 NOISE LEVEL INSIDE CAB....................................................................................................................... 1.3 PARKING THE MACHINE........................................................................................................................ 1.10 PROTECTIVE CLOTHING......................................................................................................................... 1.4 SAFETY LABELS..................................................................................................................................... 1.27 SAFETY PRECAUTIONS, GENERAL....................................................................................................... 1.4 SAFETY PRECAUTIONS, OPERATING.................................................................................................... 1.9 SAFETY PRECAUTIONS, SERVICING................................................................................................... 1.12 SAFETY SYMBOLS................................................................................................................................... 1.4 SIGNAL WORDS........................................................................................................................................ 1.4 VIBRATION LEVELS INSIDE CAB............................................................................................................ 1.3 WELDING, PRIOR TO............................................................................................................................. 1.12 WORKING WITH OIL................................................................................................................................. 1.6

Safety

Tigercat 610E/615E Skidder

1.2

Tigercat 610E/615E Skidder

Safety

VIBRATION AND NOISE LEVEL INSIDE CAB VIBRATION AND NOISE LEVEL INFORMATION TO FOLLOW, NOT AVAILABLE AT TIME OF PRINTING.

Wear suitable hearing protective device such as earmuffs or earplugs to protect against noise.

Prolonged exposure to loud noise can cause permanent hearing loss. This machine exceeds 70dB(A) in the cab and exceeds 85dB(A) when servicing machine engine.

Check with your local Safety Commission to determine if hearing protection is required at these levels.

1.3

Safety

Tigercat 610E/615E Skidder

SAFETY SYMBOLS

GENERAL SAFETY PRECAUTIONS Remember that safety is a prime responsibility of all.

To minimize the risks and promote safety at all times, this section of the operator’s manual details a number of safety rules which should always be followed and obeyed.

This safety alert symbol means ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

Always read the operator’s manual before operating the machine. Pay close attention to WARNINGS and HAZARD identifications.

The safety alert symbol identifies important safety messages on machines, safety signs, in manuals, or elsewhere. When you see this symbol, be alert to the possibility of personal injury or death. Follow the instructions in the safety message.

Study all the safety messages in this manual and on the labels on the machine carefully.

Understanding Signal Words

DANGER DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

Follow all instructions from safety inspector and supervisors.

WARNING

You must be fully trained to operate this piece of equipment. Know the capabilities and the limitations of the equipment. Learn the most efficient operating techniques.

WARNING indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

Do not let an untrained person operate the machine.

CAUTION CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.

Use recommended protective clothing and safety devices such as gloves, safety boots, safety hat, goggles, and ear protection when necessary.

1.4

Tigercat 610E/615E Skidder

Safety

These safety rules highlight both general and specific measures the operator should be familiar with and adhere to. More specific measures are illustrated with pictograms which may also be attached to the machine in locations pertinent to their respective message. Keep safety labels in good condition. Repair or replace damaged labels.

WARNING

Avoid mounting or dismounting the machine in areas with slippery surfaces.

Dry, deice, clean up or cover slippery surfaces with an anti-slip material before mounting or dismounting the machine.

Wear suitable hearing protective device such as earmuffs or earplugs to protect against noise.

Prolonged exposure to loud noise can cause permanent hearing loss.

WARNING Do not walk on machine surfaces with steel cleated foot wear. Steel cleats on steel surfaces are slippery and do not provide a safe foot hold.

Always use the handrails and steps provided when mounting and dismounting from the machine.

WARNING It is not recommended to walk on machine surfaces that are not designated walking areas.

No attempt should be made to walk on angled steel surfaces or surfaces that are irregular in shape.

Do not jump off the machine at any time.

Walking surfaces on the machine must be covered with anti-slip materials to provide a safe foot hold and prevent slipping.

Do not try to climb onto or off of a moving machine.

Do not use the joystick as a handle when entering or leaving the cab.

These anti-slip surfaces should be maintained on a regular basis. If the surface shows signs of wear, the anti-slip material must be replaced immediately.

When mounting or dismounting the machine always use the 3 point technique - Use one hand with 2 feet or 2 hands with one foot.

1.5

Safety

Tigercat 610E/615E Skidder

To reduce the risk of fire, machines should be completely cleaned of debris at least daily, particularly around the engine exhaust components. Hydraulic oil leaks, excess grease, fuel and oil accumulation (including spillage) should be eliminated immediately, always turn the engine off before cleaning machine.

Check all fluid levels.

Do not operate the machine with any of the exhaust system, safety covers, or other devices removed.

Do not operate the machine with the cab retaining pins removed. Always install retaining pins and fasten front guards to cab roof after lowering the cab.

Maintain a clean cab interior, clear away trash or debris.

Machine should be washed completely at every major service.

Inspect the machine daily for signs of damage or unusual wear, to ROPS, FOPS, OPS structures.

The machine should be inspected daily for signs of fluid leaks, damage, unusual wear, or faulty operation. Repair or replace malfunctioning parts and systems immediately.

Keep a first aid kit in an easily accessible location on the vehicle at all times.

Check window and door guards for damage.

Working with oil

Check protective windows for cracks, a damaged window has reduced strength to stop flying objects. All damaged windows must be replaced with original equipment.

Direct contact with oil implies a risk of skin complaints (example: eczema). Strict hygiene should always be observed.

Check windows for scratching, crazing and cloudiness that could impair clear visibility all round the machine.

Some advice which should be observed:

Do not operate the machine with any defective or inoperable components.

• •

•

•

• • • • • •

Oils used in this machine may be hot enough to cause serious burns.

Avoid contact with oil, particularly heated oil.

Oil on the skin should be washed off immediately with soap and water.

Wear protective gloves. Hands should be clean before putting on gloves. Apply protective cream to the hands to make washing easier.

Don't put oily rags in your pockets.

Oil soiled clothing should be changes as soon as possible.

Always keep an extra overall handy, but not in the machine where it can become dirty.

Cuts and abrasions must be attended to immediately. Clean them and apply first-aid.

Avoid breathing in oil fumes.

Wash hands and arms frequently (example: at each meal break or as often as possible).

Safety Hazards - Viton Seals O-rings and other seals manufactured of Viton material (fluorine rubber) produce a highly corrosive acid (Hydrofluoric) when subjected to temperatures above. 600°F(315°C).

This contamination can have extreme consequences on human tissue since it is almost impossible to remove after contact.

1.6

Tigercat 610E/615E Skidder

Safety

The following procedures are recommended when inspecting equipment that has been subjected to high temperatures such as fire: •

If State/Provincial, local or job site regulations require even greater safety distances than stated above, adhere strictly to these regulations for your own protection.

Visually inspect any seals or gaskets which have suffered from heat; they will appear black and sticky.

•

If these are found, Do Not Touch!!!

•

Determine the material composition of any seals or gaskets, If fluro-elastomer seals (Viton, fluorel, or tecmoflon) have been used, the affected area must be decontaminated before undertaking further work. Natural rubber and nitrile materials are not hazardous.

•

Disposable heavy duty gloves (neoprene) must be worn and the affected area decontaminated by washing thoroughly with limewater (Calcium Hydroxide solution).

•

Any cloths, residue and gloves must be safely discarded after use.

If the machine must be transported, make sure that it is adequately secured to the transporting vehicle. Refer to TRANSPORTING INSTRUCTIONS in SECTION 2 of the OPERATOR'S MANUAL. Stopping the engine immediately after it has been working under load can result in overheating and premature wear of the engine components.

Reduce engine speed to LOW IDLE and let run for approximately 5 minutes to allow gradual dissipation of heat and also to reduce turbo speed.

This will also prevent loss of coolant by after boil and possible hot spot damage to the engine.

Even though the brakes are fully engaged, block the wheels to prevent movement during transport.

Install articulation lock whenever the machine is to be transported.

NOTE: Burning discarded items is not recommended except in an approved incineration process where the dangerous products are treated by alkaline scrubbing.

Safety Hazards - Operating Maintain a charged fire extinguisher on the vehicle at all times and KNOW HOW TO USE IT.

Be aware when performing service and maintenance tasks that surfaces and grab handles in and around the engine and cooling system may become very hot when the engine has been running. Contact with hot surfaces may cause injury.

Do not carry passengers either in the cab or anywhere else on the machine. The vehicle seating accommodation is for one operator only.

Do not allow anyone to operate the machine who may not be physically fit or who may be under the influence of alcohol or drugs.

Comply with instructions in this manual and also your company’s regulations for the operation of this machine.

When operating the machine, ensure there is adequate clearance on both sides and above the machine or any of its attachments. Additional clearance may be necessary where the ground is uneven.

Read, understand and follow all general safety precautions specified by grapple head manufacturer.

Extreme caution should be exercised when approaching any area where overhanging electrical power lines are present. Serious injury or death by electrocution can result if the machine or any of its attachments are not kept a safe distance from these lines.

Access to a cell phone or radio to call for assistance in an emergency is advised. Be aware that signal strength for cell phones and radios changes with terrain and location.

WARNING

Do not move any part of the machine or load within 10 feet (3m) plus 2 times line insulator length of any electric lines.

Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

1.7

Safety

Tigercat 610E/615E Skidder

Avoid Injury from Backover Accidents

WARNING

Before moving machine, be sure all persons are clear of the area.

Battery posts, terminals and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

Wash hands after handling.

Always be alert for bystanders moving into the work area. Use horn to warn bystanders before moving the machine.

When using a signal person, keep the person in view at all times. Always be sure the signal person is clear before backing up.

If acid is accidentally splashed into your eyes, flush immediately with clean water and get medical attention.

To avoid backover accidents:

Do not attempt to charge a frozen battery; it can explode.

•

Disconnect battery before working on electrical systems. Remove ground terminal first when disconnecting. Connect ground terminal last when reconnecting.

•

Do not short out battery terminals for any reason.

Serious burns or an explosion can result.

• •

CAUTION Lead-acid batteries contain sulfuric acid which can severely damage eyes or skin on contact. Always wear a safety face shield, rubber gloves and protective clothing to reduce risk of accidents.

Lead-acid batteries produce flammable and explosive gasses. Keep arcs, sparks, open flames and lighted tobacco a safe distance from the batteries.

• •

1.8

Always look around before you back up. Be sure that everyone is clear.

Keep reverse warning alarm in working condition. The reverse warning alarm must sound when the machine is moving in reverse.

Use a signal person when backing up if view is obstructed. Always keep the signal person in view.

Learn the meaning of all flags, signs and markings on the job site and who is responsible for signalling.

Keep windows, mirrors and lights in good condition.

Dust, heavy rain, fog, snow etc. can reduce visibility. As visibility decreases, reduce speed and use proper lighting.

Tigercat 610E/615E Skidder

Safety Diesel Exhaust Fluid (DEF) may irritate eyes or skin. Do not get in eyes. Do not get on skin.

OPERATING SAFETY PRECAUTIONS

First Aid treatment: DEF Contains Urea. If swallowed call a Poison Control Centre or doctor immediately. Do not induce vomiting. If in eyes rinse with water for 15 minutes. If on skin rinse well with water. If irritation persists seek medical treatment.

WARNING Use only diesel exhaust fluid (DEF) which meets ISO 22241 specifications. NEVER fill the DEF tank with any other fluid.

DEF fluid is injected into the exhaust gas stream during normal operation of the Selective Catalytic Reduction (SCR) aftertreatment system.

Use of other fluids may cause component damage, or a fire risk which could result in death or serious injury.

Turn the engine off when refuelling - DO NOT refuel the engine while smoking or near open flame or sparks.

Attach a grounding strap to an unpainted metal surface on the machine if the refuelling tank or nozzle is so equipped.

Check that no other personnel have moved into a hazardous area before starting the machine.

Sound the machine horn before starting the machine.

CAB EXITS There are three ways to exit the cab in case of an emergency.

The operator's seat is equipped with a lap belt. Use this restraint system at all times when operating the machine.

1. Left hand cab door, one of the two main points of entry.

2. Right hand cab door, one of the two main points of entry.

3. Sliding windows in the cab doors, this is a third cab exit for use if the cab doors become blocked.

It is important that the operator of the machine be familiar with these emergency exits and how to use them.

Start the engine by following the instructions in this manual. Refer to OPERATING MACHINE in SECTION 2 of the OPERATOR’S MANUAL.

All three exits should be checked to make sure that they are operational and will function in an emergency.

IMPORTANT !

Unlock both doors before operating machine to allow opening from the outside in case of an emergency. Make sure that the doors are operational, open the doors twice, once using the exterior handle and once using the interior latch handle.

WARNING • EXPLOSION HAZARD. • DO NOT USE ETHER. • ENGINE EQUIPPED WITH HEATER STARTING AID. • USE OF ETHER COULD RESULT IN DEATH OR SERIOUS INJURY.

For additional information, refer to EMERGENCY EXITS in SECTION 3 of the THIS MANUAL.

36782BENG R0

Secure loose items in cab.

Never use a liquid staring aid to start an engine.

Prior to commencing work, check all equipment controls to ensure that the machine responds correctly.

Before moving the machine to the work site, check to ensure that all doors, panels, and access covers are installed properly and secured.

1.9

Safety

Tigercat 610E/615E Skidder When parking the machine:

Make sure that all safety screens and guards are installed and properly secured.

Do not open an escape hatch or the cab doors to increase ventilation when operating the machine.

WARNING

•

Park on level ground ONLY and engage parking brake

•

Do not park on a hillside or incline.

•

Before leaving the operator's cab, lower the grapple and dozer blade onto the ground and engage the parking brake.

•

Stop the engine and release pilot system pressure by performing the following steps: 1. Fully apply brake foot pedal repeatedly until there is no pedal resistance. This may take a minimum of 150 applications.

Keep the cab doors closed when driving or steering the machine to prevent accidental entry of branches and debris into the cab.

2. Pressure may remain in the system after completing all of the above steps.

Use caution when loosening hydraulic connections.

Keep cab doors closed and use seat belt when driving or steering the machine to prevent being thrown from the operator's cab.

Never operate the winch from the ground. Control it only from the operator’s seat.

Never use the parking brake to slow down or stop the machine except in an emergency.

Keep the parking brake properly adjusted at all times.

Keep service brakes properly adjusted and check for proper operation of the service brake. Refer to SERVICE BRAKE – CHECKING BRAKE AND ACCUMULATOR FOR PROPER OPERATION in SECTION 3 of THIS MANUAL.

620E-063

•

Always rest the grapple and dozer blade on the ground when operation is stopped, regardless if the engine is running or turned off.

Never work alone. Regularly inform other crew members of your intentions, location and length of time to perform duties.

Park machine at least 50 feet (15 meters) away from other equipment and in a cleared area. In the event of a fire, this distance will minimize the chance of the fire spreading to other equipment.

Do not leave the operator's cab while the winch cable is under tension.

Before leaving the operator's cab, lower the grapple and dozer blade to the ground and engage the parking brake.

If out of the operator’s cab for an extended period shut the machine off.

Turn the battery disconnect switch off if the vehicle is to be parked for an extended period of time (Example - overnight).

WARNING

When the engine is running, DO NOT allow anyone in areas of the machine where they may be crushed by moving components.

Maintain a safe operating distance between the machine and workers and all other personnel. It is the duty of the operator to ensure that no person approach the machine while in use, the risk zone is 60 m (200 feet).

1.10

Tigercat 610E/615E Skidder

Safety • •

WARNING

Do not winch in a load at a sharp angle. This could cause your machine to tip over.

Do not overload your skidder as this can create an unstable condition and cause a roll-over.

CAUTION Never operate the boom or grapple over the heads of bystanders.

When reeling in winch cable, make sure all ground personnel are at a safe distance, at least 1 1/2 times the working length of the cable, in case of rolling logs or whipping cables.

Ground personnel should maintain a safe distance, at least 1 1/2 times the working length of the cable, from a winch cable under tension.

If the machine is to travel on public roads, use accessory lights (when installed) and other caution devices to alert operators of other vehicles of your presence. Ensure your machine meets all regulatory requirements.

Use only prearranged and approved signalling practices.

Obey flagger's signal and signs

When transporting the machine, ensure that enough clearance is available on both sides and above the machine or any of its attachments to avoid contact with power or telephone lines, bridge structures, etc.

Operate the machine only from a seated position in the operator’s seat.

Do not carry passengers either in the cab or anywhere else on the machine.

If vision is limited by dust, smoke, fog or snow, stop the machine until visibility is restored.

Before transporting the machine check to ensure that all doors, panels and access covers are installed properly and secured.

Do not work below or behind a skidder parked on a grade.

Read, understand and follow all general safety precautions specified by winch manufacturer and in this manual.

When working on slopes, travel straight up or down the slope to prevent roll-over.

NEVER travel across a STEEP slope or side hill:

• • • •

Before moving the machine, lift the grapple and dozer blade off the ground and keep them high enough to clear obstacles such as stumps.

Check for correct tire air pressure. If the pressure is too low it will result in swaying. If the pressure is too high it will result in bouncing. Refer to also to TIRE PRESSURES in SECTION 3 of THIS MANUAL.

When operating the winch with ground personnel, keep the personnel in view at all times and ensure ground personnel are never allowed to be in line with the load.

•

Do not open cab doors or window screens when machine is on a slope. The doors and screens are heavy and could swing out with considerable force.

When operating the winch do not work with a damaged cable. Broken wire or strands, or a decrease in the diameter of a cable are warning signs of a damaged cable. Do not anchor a double or two part line to the winch.

If you travel across a MODERATE slope, NEVER make an uphill turn as this could cause a tip-over situation.

Keep load low and close to skidder for best stability.

A load of logs will change the handling and stability of the skidder.

Always be prepared to dump the load in case of emergency.

Never approach an unstable log from the downhill side.

Read, understand and follow all general safety precautions specified by grapple head manufacturer.

1.11

Safety

Tigercat 610E/615E Skidder This machine may be equipped with an optional variable pitch cooling fan, fan blade pitch is hydraulically varied to control the flow and direction of air through the cooling assembly.

Exercise care when working in this area with the engine running. If the FAN CONTROL SWITCH is in the AUTOMATIC position, the fan could go into CLEAN mode at any time when the engine is running.

SERVICING SAFETY PRECAUTIONS

Always ensure that the fan guard is in place when the engine is running.

IMPORTANT

24 VOLT

Conduct maintenance inspections at least as frequently as recommended in section 3 this manual.

ELECTRICAL SYSTEM

When servicing or repairing equipment, shut the engine down and turn OFF the battery disconnect switch. Some wiring on the machine is live even when the battery disconnect switch is off.

Prior to welding on any part of the machine, it should be cleaned and a fire extinguisher should be made available at the welding location.

When servicing the electrical system, turn OFF the battery disconnect switch, remove the battery cables from the batteries disconnecting the negative (-) cables first. Perform the service work, then attach the battery cables reconnecting the positive (+) cables first and turn the battery disconnect switch ON.

Care must be taken in attaching the welding machine grounding clamp so current does not pass through bearings, especially the centre joint bearing.

Turn OFF the battery disconnect switch.

Install a “DO NOT START ENGINE” sign on the operator’s cab door and in the engine compartment when making repairs to the machine.

Disconnect the battery cables from the batteries, negative (-) cables first.

This machine is equipped with sensitive electronic control equipment, prior to welding:DISCONNECT THE TWO MULTI-PIN PLUGS FROM THE ENGINE ECU

Before performing maintenance or repair work on any equipment, consult the manufacturer’s instruction manual and follow recommended procedures.

The radiator and the engine cooling system should be cleaned and serviced daily to maintain moderate engine temperatures.

630E-297

ENGINE ECU DISCONNECT - LEFT SIDE

Disconnect the engine ECU (electronic control unit) by unplugging the two connectors from the left side of the engine.

1.12

Tigercat 610E/615E Skidder

Safety LOCATED UNDER CAB, RIGHT REAR - REMOVE COVER TO ACCESS MODULES

DISCONNECT ENGINE GROUND CONNECTION

XA2-A0 FRONT CHASSIS CONNECTOR XA2-A1 FRONT CHASSIS 2

CONNECTOR 610E-002

ENGINE GROUND DISCONNECT - RIGHT SIDE

615C-007

Also disconnect the engine ground connection at the chassis.

XA2 MODULES

Disconnect the other IQAN control module harness connectors. One module is located in the cab. Two modules are located under the cab.

When welding is completed reconnect all connectors, ground and fuse then attach the battery cables reconnecting the positive (+) cables first and turn the battery disconnect switch ON.

WARNING 620E-007

FUSE AND RELAY PANEL

Remove the MD3 module fuse from the fuse and relay panel LOCATED IN CAB BEHIND LEFT KICK PANEL

WARNING, HOT FLUIDS AND HOT MACHINE SURFACES CAN CAUSE SERIOUS BURNS!

CONNECTOR

620E-043

XS2-A0 MODULE - CAB

1.13

•

Before servicing the machine, allow the engine cooling system, fuel system, exhaust system, hydraulic system and machine surfaces to cool down.

•

Use a thermometer to check surface and system temperatures to ensure it is safe to begin service work.

•

DO NOT begin service work until the surface or system temperature has cooled down to below 100°F (38°C)!

Safety

Tigercat 610E/615E Skidder WARNING

Diesel fuel or hydraulic oil under pressure can penetrate the skin and cause serious personal injury, blindness, or death. If any fluid is injected into the skin, it must be surgically removed within a few hours by a doctor familiar with treating this type of injury.

Never use your bare hands to check for fluid leaks.

Do not change any pressure or relief setting unless Tigercat authorized instruction has been obtained.

Use the proper tool for the job. Repair or replace worn or damaged tools including lifting equipment immediately.

Fluid leaks under pressure may not be visible.

When searching for leaks, wear work gloves and use a wrench or piece of wood to move hydraulic hoses. Do not grab hold of hydraulic hoses. Wear safety goggles for eye protection.

Pressure can be maintained in a hydraulic system long after the power source and pump have been shut down. Lower grapple and dozer blade to the ground and relieve trapped pressure from the brake accumulator before performing work on components, or disconnecting any hoses. For the procedure to RELIEVE PRESSURE, refer to PARKING THE MACHINE in THIS SECTION.

Keep your hands, feet, head, and loose clothing away from power driven parts. Tie long hair behind your head. Remove rings and other jewellery to prevent electrical shorts and entanglement in moving parts.

WARNING

Always be aware of machine pinch points that could cause injury. Never place body parts within the range of motion of the working parts of the machine.

Always wear your safety gloves when handling cables, chokers or logs.

Explosive release of fluids from pressurized cooling system can cause serious burns.

Turn the engine off. Only remove radiator fill cap when cool enough to touch with bare hands.

Slowly loosen cap to first stop to relieve pressure before removing completely.

1.14

Tigercat 610E/615E Skidder

Safety CAUTION Do not open cab doors or window screens when machine cab is tilted . The doors and screens are heavy and will swing out with considerable force.

SAFETY CABLE

630E-060

610E-015

ARTICULATION LOCK IN STRAIGHT LOCKED POSITION

CAB AT FULL TILT SUPPORTED

BY SAFETY CABLE

SUPPORT BRACE

630E-073

ARTICULATION LOCK IN ARTICULATED LOCKED POSITION

Before working in the centre joint area, install the frame articulation lock between the frames to prevent accidental articulation and injury. Always replace the lock bar in its storage position after use.

WARNING 620E-009

DO NOT work below or behind a machine that is parked on a grade.

TILTED CAB SUPPORTED

BY SUPPORT BRACE

Before working under cab, machine must be parked on level ground. Cab must be fully tilted with safety cable completely tight or cab support brace must be installed between frame and cab to prevent injury. Refer to TILTING THE CAB in SECTION 3 of THIS MANUAL for complete instructions.

WARNING Failure to follow all of the above instructions could result in serious injury or death from crushing.

The hydraulic cylinder is to raise and lower cab, it must not be used as a support.

Never stand under an object supported with hydraulics. Always use safety stands or a locking device.

All handles should be hand tight only at all times.

This is particularly important for easy access to the pressurized water system (if equipped) in the event of a fire or other emergency. Refer also to FIRE PREVENTION in THIS SECTION. 1.15

Safety

Tigercat 610E/615E Skidder BOLT ON ACCESS PANELS

MAINTENANCE ACCESS DOORS

DOOR PROP

610E-023

610E-025

MAINTENANCE ACCESS DOOR (RIGHT SIDE SHOWN)

ACCESS PANELS LEFT SIDE

BOLT ON ACCESS PANELS

If the engine is running inside a building, ensure that sufficient ventilation is available to prevent a build-up of toxic exhaust fumes. Run the engine only when it is necessary for testing or adjustments.

Work in a ventilated area. If it is necessary to run an engine in an enclosed area, use an exhaust pipe extension to remove toxic exhaust fumes.

If you don't have an exhaust pipe extension, either work outside, or open the shop doors.

MAINTENANCE ACCESS DOORS

610E-003

ACCESS PANELS RIGHT SIDE

CAUTION

Always use the door props provided to safely hold access doors open while in use.

The engine compartment access panels are bolted in place. Whenever bolts are removed panels can fall during the process of removing them from the machine.

Dispose of fluids properly.

Do not pour fluids into the ground, stream, pond.

Before draining any fluids, know the proper way to dispose of them.

1.16

Tigercat 610E/615E Skidder

Safety

FLUID INJECTION INJURY

WARNING

Hydraulic and diesel fuel systems on forestry machines operate at very high pressures, often 207 bar (3000 psi) and above. If a loose connection or a defect in a hose should occur, a fine, high velocity stream of fluid will result. Even for systems pressurized to as little as 7 bar (100 psi), this fluid stream can penetrate human skin as if it were a hypodermic needle.

Diesel fuel or hydraulic oil under pressure can penetrate the skin and could result in death or serious injury. If any fluid is injected under the skin, a medical doctor familiar with the treatment of this type of injury must surgically remove it within a few hours.

In the event of any suspected fluid injection injury • Report the injury to your supervisor immediately.

• Seek professional medical attention immediately.

As always the best defence against suffering the effects of fluid injection is to prevent the accident from occurring in the first place.

When searching for possible fluid leaks • Never search for leaks with your bare hands.

Always wear thick protective gloves.

• Be sure to wear safety goggles for eye protection.

• Keep all body parts well away from the area being investigated for leaks.

Initially, an accidental fluid injection beneath the skin may only produce a slight stinging sensation.

There is a danger that you will tend to ignore this, thinking that it will get better with time. Most often, it does not! Within a very short time the wound may begin to throb painfully, indicating that tissue damage has already begun.

Similarly fluid injected directly into a blood vessel can spread rapidly through your circulatory system. The human body has little ability to purge injected fluid.

Diesel fuel or hydraulic oil under pressure can penetrate the skin and could result in death or serious injury. If any fluid is injected under the skin, a medical doctor familiar with the treatment of this type of injury must surgically remove it within a few hours.

•

Time becomes critical as tissue damage progresses rapidly. The longer you delay getting professional medical attention, the more damage can occur.

Although fluid injection accidents are rare, the resulting injury has on occasion required the amputation of a finger, a hand or in some cases the entire limb. The longer the delay in getting professional medical aid, the further up the limb the tissue damage can spread. An injury of this type can become very serious or even fatal if not dealt with promptly and properly.

1.17

Use the end of a long piece of wood to move hoses or other obstacles.

• Place the end of a long piece of wood in the suspected path of any fluid stream. Never use any part of your body.

• Recognize that the source of the leak and the fluid streaming from it may be very small and not easily visible. You may only be able to see the fluid that accumulates as a result of the fluid stream.

When performing any service work • Stop the engine and relieve all diesel fuel or hydraulic pressure before disconnecting any lines or otherwise working on the system.

• Never grab any hydraulic or diesel fuel connectors or hoses when they are subjected to pressure.

• Always ensure that hoses are rated for the pressures to which they will be subjected.

• Never use any hoses that you suspect could be defective.

Safety

Tigercat 610E/615E Skidder

GREASE INJECTION INJURY WHEN USING PNEUMATIC GREASE GUNS Pneumatic grease guns can deliver grease at pressures from 17 - 400 bar (246 - 5801 psi).

It takes less than 7 bar (100 psi) to inject a substance through human skin.

ALWAYS get professional medical treatment immediately after any type of injection injury.

Provide the physician with information on the type of grease, the pressure setting of the gun, and similar details.

The amount of fluid injected, type of fluid (or material), pressure at which it was injected, and the elapsed time between injection and surgery all influence the chances of successful treatment for this type of serious injury.

Prior to using a high pressure pneumatic grease gun perform the following: •

All operators of high pressure pneumatic grease guns MUST be trained in the hazards of its operations and the treatment for such injuries.

•

DO NOT OPERATE a high pressure pneumatic grease gun unless you have been trained in the proper operation and are aware of all safety precautions of such a tool.

•

Wear protective clothing such as gloves, safety hat and safety glasses.

•

Inspect all parts of the grease gun for wear and tear and replace all worn or damaged parts.

•

Ensure that protective shrouds are installed on all grease gun nozzles as safety devices.

•

Remove dirt and grease from grease fittings prior to greasing.

•

Replace any defective grease fittings on equipment with new fittings immediately.

•

When badly positioned fittings are identified, replace them with angled or swivel fittings for easier access.

1.18

Tigercat 610E/615E Skidder

Safety LIGHTNING SAFETY

LIGHTNING SAFETY AWARENESS

In spite of the popular myth that being struck by lightning is an unlikely event, the facts show that lightning strikes occur frequently. As a result loggers are at high risk because their work is outdoors and close to known strike points such as tall trees and heavy equipment.

Loggers can increase their chances of avoiding a lightning strike by following a few simple safety practices.

1. Designate a member of your crew to

WHAT IS A LIGHTNING STRIKE? Lightning is a discharge of the electricity produced by a thunderstorm. As the thunderstorm develops, many small particles of ice within the storm clouds bump together. These collisions create a positive charge at the top of a cloud and a negative charge at the bottom. As this continues a second positive charge builds up on the ground beneath the cloud, concentrated around high objects such as hills, trees, buildings, equipment and even people.

•

Monitor daily weather forecasts

•

Observe local weather conditions

•

Alert all other members of the crew when a possible lightning threat develops.

2. Don’t start or continue any work that cannot be stopped immediately, when a storm moves nearby.

3. Anticipate a high-risk situation and take action early by moving to a low-risk location. Do not hesitate. If there is lightning, you are in danger.

When the difference between the electrical charge in the cloud and on the ground becomes great enough to overcome the resistance of the insulating air between them, an electrical current flows instantly. This is a lightning strike.

4. Obey the rule - If you see lightning, Flee. If you hear thunder, Clear.

5. Do not follow the now obsolete guideline to take shelter when the time between seeing lightning and hearing thunder is 30 seconds or less. This does not provide sufficient time to ensure safety. Always follow step 4.

The electrical potential in a lightning strike can be as much as 100 million volts. Lightning strikes can occur over very large distances, even as much as 60 km (37 miles). Lightning travels both in front of and behind a thunderstorm and so strikes happen even when rain has not started or has stopped.

Lightning can hit in the same place, many times and often spreads out over 18 m (60 feet) within the soil around the strike point.

6. Remain in your safe location for 30 minutes after the last sight of lightning or the last sound of thunder.

The safest location during lightning activity is inside a fully enclosed, substantially constructed building, a house, office, school, shopping area, etc. These are the safest because of the electrical wiring and plumbing that they contain. Should lightning strike, the electrical current will travel through the wiring or plumbing into the ground.

When such a building is nearby, always seek shelter there first.

Thunder always accompanies lightning. When lightning occurs, the air through which it travels is instantaneously heated to a temperature more than 28,000°C (50,000°F). The air expands rapidly due to this heating, then quickly contracts as it cools. It is this contracting shock wave that we hear as thunder.

In many areas of the world, lightning strikes are second only to flooding as the greatest cause of storm related deaths and injuries. Although only 10% of lightning strike victims are killed, virtually all from cardiac or respiratory arrest, over 70% of those that survive suffer severe, life-long injury and disability. The symptoms of a lightning strike include memory loss, fatigue, chronic pain, dizziness, sleeping difficulty and the inability to complete several tasks at one time.

1.19

Safety

Tigercat 610E/615E Skidder WHAT TO DO IF YOU ARE OUTSIDE AND SEE LIGHTNING OR HEAR THUNDER. If you can, get inside.

1. Run to the nearest building, motor vehicle or fully enclosed ROPS equipment cab immediately. Being anywhere outside is not safe.

2. If inside a building:

Unfortunately loggers do not often work close to buildings and therefore other alternatives need to be considered.

Sheds, weather shelters, hunting blinds, tents and other partially open or small structures are not safe against lightning strikes as they lack the electrically grounded components of larger buildings. They are intended for sun or rain protection only. Do not seek shelter from lightning strikes inside these structures.

•

Don’t watch the lightning storm from open windows or doorways. Stay in inner rooms.

•

Stay well away from corded telephones, electrical appliances, lighting fixtures, radio microphones, electrical sockets and plumbing pipes and fixtures.

3. If inside a motor vehicle or fully enclosed ROPS equipment cab:

The second safest location during lightning activity is inside a fully enclosed car, van, truck or bus with a metal roof and metal sides. The electrical energy of a lightning strike to these vehicles is carried to ground by the conducting outer metal surfaces.

This is called the skin effect.

Do not seek safety from lightning strikes in vehicles with fiberglass or plastic body shells or in convertible top vehicles. None of these are safe, as they do not offer skin effect lightning protection.

Heavy forestry equipment such as a skidder, loader, feller buncher, forwarder, etc. with a fully enclosed rollover protective structure (ROPS) cab take advantage of the skin effect and are therefore safe in electrical storms.

However machines with a rollover canopy only are not safe against lightning strikes as they are open to electrically conductive rainwater and do not benefit from the skin effect. Operators of this equipment must abandon their machines and get to a safer location before lightning strikes.

Note that the rubber tires on motor vehicles and heavy equipment do not increase safety from lightning strikes. Lightning has already travelled a great distance through the air to strike the vehicle.

In comparison a few inches of rubber in a tire offers absolutely no additional insulation.

1.20

•

Under no circumstances whatsoever step outside of the vehicle or off the equipment to move to another shelter. Very dangerous electrical pathways to ground may go through you.

•

Shut down all operation, turn off the engine, close all doors and raise all windows.

•

Sit squarely in the seat with your hands in your lap and your feet flat on the floor mat.

•

Do not touch any metallic objects referenced to the outside of the vehicle. Do not touch any door and window handles, control levers, foot pedals, steering wheels, cab interior walls and any other inside to outside metal objects.

•

Do not touch any radio or telephone connected to an outside antenna.

Tigercat 610E/615E Skidder

Safety What to do if you feel your skin tingling, your hair stands on end, light metal objects vibrate or you hear a crackling sound.

1. Lightning is probably about to strike. You only have a few seconds to act.

2. Put your feet together. Crouch down like in a baseball catcher’s position. Hold your head down. Cover your ears to protect them against the noise of the thunder.

3. Do not lie flat on the ground. By touching as little of the ground as possible, the lightning may not move across the ground to you.

If you are caught outside and have no where else to go.

What to do if a co-worker has been struck by lightning.

1. Avoid wide-open areas where you project above the surrounding landscape.

1. The victim does not carry any electrical charge. There is no danger to anyone helping this person. You can touch him or her immediately.

2. Seek shelter in a low place, such as a ditch, ravine, valley, canyon or cave.

3. Get away from open water such as ponds or streams.

2. Call your local emergency response telephone number immediately.

4. Do not take shelter under any isolated tall trees or small groups of trees.

3. If the victim has no pulse, their heart has stopped or they have stopped breathing, start cardiopulmonary resuscitation (CPR) or mouth –to-mouth resuscitation immediately. Use a portable defibrillator if one is available.

5. Seek shelter amongst the dense, thick growth of the shortest trees.

6. Avoid entering any small enclosures or shelters.

4. Be careful about staying in the storm to take care of the victim. You can get hit by lightning too. If you can, move the victim to a building as soon as possible.

7. Do not seek shelter under any motor vehicle or heavy equipment.

8. Keep clear of any materials that can conduct electricity such as wire fences and gates, metal pipes, poles, rails and tools.

To further increase your awareness about lightning safety, see the following web sites.

9. Stay at least 15m (50 feet) away from metal objects such as a fuel tank, a vehicle or machinery without a cab, motorcycle, ATV, etc.

10. Stay at least 5m (16 feet) apart from any other members of a group so that lightning won’t travel between you.

11. Do not use the telephone except for emergencies.

1.21

National Weather Service Lightning Safety http://www.lightningsafety.noaa.gov National Lightning Safety Institute http://www.lightningsafety.com

Safety

Tigercat 610E/615E Skidder 4. Clean out all accumulated forest debris (twigs, pine needles, branches, bark, leaves, saw dust, small wood chips) and any other combustible materials from inside the machine belly pans or lower machine structures as well as from areas in proximity to the engine, fuel and hydraulic oil systems no less frequently than at the completion of each work shift.

FIRE PREVENTION

5. Inspect the machine regularly for any signs of diesel fuel or hydraulic system leakage.

Check for worn or eroded fuel or hydraulic lines before starting up any equipment.

When working in a forest environment, it is impossible to prevent combustible debris from collecting in tight corners of the machine. This debris, in itself, may cause a fire; however, when mixed with fuel, oil or grease in a hot or confined place, the danger of fire is greatly increased.

6. Clean up any grease, diesel fuel, hydraulic and lubricating oil accumulation and spillage immediately.

The following fire prevention guidelines should be used to supplement the operator’s fire prevention efforts. In no case should the guidelines be used, or assumed, as replacements for diligent operator efforts at preventing fires.

The following guidelines will help to keep your equipment up and running efficiently and keep the risk of fire to a minimum.

1. Maintain a CHARGED fire extinguisher on the machine at all times and KNOW HOW TO USE IT. 2. Remove debris and blow out dust regularly from the air intake doors, engine radiator and charge air cooler, hydraulic oil cooler, diesel fuel cooler and air conditioning condenser core to prevent overheating of the engine and hydraulics and to maintain efficient operation of the machine. Refer to CLEANING A/C CONDENSER, OIL COOLER AND RADIATOR in SECTION 2 of the OPERATOR’S MANUAL. 3. Blow off all forest debris and fine organic material accumulated near hot engine exhaust components (turbocharger and exhaust manifold as well as exhaust pipes and muffler) at the completion of each work shift or more frequently when working in logging conditions where large amounts of combustible forest debris are present.

Visual inspection after blow off to ensure thorough cleanliness is vital. Engine exhaust systems provide numerous small pockets where saw dust, small wood chips and other flammable forest debris can gather. Even small accumulations close to hot exhaust components can ignite and smoulder. If dislodged this smouldering debris can fall into other areas of the machine and thereby spread a fire.

7. Steam clean the engine, hydraulic pumps, transmission, brake, fuel and hydraulic tank compartments and all machine belly pans at least once a month or more frequently when working in logging conditions where large amounts of combustible forest debris are present.

8. Use only nonflammable solutions for cleaning the machine and components.

9. Inspect the exhaust system daily for any signs of leakage. Check for worn, cracked, broken or damaged pipes or muffler. Also check for missing or damaged bolts or clamps.

Should any exhaust leaks or defective parts be found, repairs must be made immediately.

Engine exhaust leaks can cause fires. Do not operate the machine until the exhaust leak is repaired.

10. During daily operation of the machine, the occurrence of exhaust leaks are usually accompanied by a change or increase in engine exhaust noise levels. These audible warnings cannot be ignored. Should any exhaust leaks occur during operation, the machine must be shut down immediately and not put back to work until the necessary repairs have been completed.

11. Park the machine at least 15 METERS (50 feet) away from other equipment at the end of each shift.

12. Never leave the machine parked with boom, arch or blade suspended off the ground. Should their supporting hydraulic hoses burn through during a fire, pressurized hydraulic oil may be injected into the fire and the boom, arch or blade will fall rapidly to the ground.

1.22

Tigercat 610E/615E Skidder

Safety

13. Turn the battery disconnect switch to OFF at shut down to de-energize all electrical circuits.

17. AFTER transporting (trucking) a machine from one job site to the next, open all doors and access panels and blow off any debris that may have repositioned itself onto the engine and exhaust parts due to wind turbulence caused by the journey.

14. Remain with the machine for at least 45 minutes at the end of operations while the machine cools.

18. Before starting repair work, such as welding, the surrounding area should be cleaned and a fire extinguisher should be close by.

19. Store rags and other combustible materials in a safe, fireproof location.

20. Do not use the machine on top of or to push piles of burning timber. A machine fire will most probably result.

EQUIPMENT FIRES ADVERSELY EFFECT YOUR ABILITY TO LOG, MAY INCREASE YOUR INSURANCE PREMIUMS DRAMATICALLY OR PREVENT YOU FROM OBTAINING INSURANCE COVERAGE AT ALL. WHAT TO DO TO PREPARE FOR A MACHINE FIRE

15. Remove all keys, lock equipment and fuel cap at the end of operations to reduce the risk of vandalism.

16. Be cautious when smoking. An open flame, a lighted cigarette, etc., should not be permitted around any vehicle, especially during fuelling operations or when the fuel system is open to the atmosphere or when servicing batteries.

1.23

•

Prevent the fire from happening in the first place by ensuring that all machine systems are frequently inspected and always well maintained.

•

Ensure that any hand held fire extinguishers are charged and in working order. Fire extinguishers require routine care. Follow the manufacturer’s instructions for inspection and maintenance shown on the label of the fire extinguisher and in the extinguisher manufacturer's manual.

•

Ensure that any pressurized water systems on the machine (if applicable) are charged and in working order. Refer to PRESSURIZED WATER SYSTEM MAINTENANCE in SECTION 3 of the OPERATOR’S MANUAL.

•

Ensure that you have the proper fire extinguishers on site. Most fires involving mobile forestry equipment will be Class A or B. Dry chemical extinguishers should be rated ABC and pressurized water extinguishers should be rated A. Class A fires involve ordinary combustibles such as wood, cloth, paper, rubber and many plastics, Class B fires occur with flammable liquids such as diesel fuel, oil and grease and Class C fires apply to energized electrical equipment.

Safety •

•

•

•

•

•

•

Ensure that the nozzle of any hand held extinguisher and pressurized water system available on the machine and at the work site fits within the fire extinguisher access holes in the doors of the machine.

Ensure that your fire detection system* is in working order. Refer to FIRE DETECTION SYSTEM in SECTION 2 of the OPERATOR’S MANUAL. Ensure that your fire suppression system** is charged and in working order. Refer to FIRE SUPPRESSION SYSTEM in SECTION 2 of the OPERATOR’S MANUAL. Ensure that you are familiar with the recommended procedures for fire contained in the emergency action plan of your company.

Ensure that you follow all national, state / provincial and local regulations dealing with fire fighting in effect in your specific geographic region. Regulations will vary from region to region but most will usually require that: 1. Workers assigned to fire fighting duties must be physically capable of performing them safely and effectively.

2. Workers designated to use fire fighting equipment as part of an emergency action plan must receive full and proper training from a qualified instructor.

3. Whenever portable fire extinguishers are provided for use in the workplace, training must be provided to familiarize workers with the general principles of fire extinguisher use and the hazards involved with fire fighting.

4. Training must be provided upon initial employment and at least annually thereafter.

Ensure that after you have received the training as outlined above, that you know how to use the fire extinguisher, the pressurized water system (if applicable) and the fire

Tigercat 610E/615E Skidder WHAT TO DO WHEN A MACHINE FIRE OCCURS •

If operating the machine when a fire occurs: 1. Lower all working attachments to the ground.

2. Shut the engine off.

3. Activate the fire suppression system**.

4. Radio or call for help. Be certain to report a fire immediately.

5. Exit the machine taking fire extinguisher and pressurized water system hose (if applicable) with you.

6. At all times ensure your own personal safety and the safety of anyone that may be in the area. Approach any fire with extreme caution. All fires can be very dangerous and life threatening.

7. Only if you can safely do so, turn OFF the battery disconnect switch.

•

Before deciding to fight the fire, be certain that: 1. The fire is small and not rapidly spreading.

2. There is always a clear, safe escape route to your back.

3. You have received training in the use of the available fire extinguishing systems and are confident that you can operate them effectively.

4. If in any doubt about whether or not to fight the fire – DON’T. Instead stand well clear of the fire and wait for help to arrive.

5. Be aware that engine coolant , diesel fuel or hydraulic hoses could fail during a fire. If this happens, hot coolant, fuel or oil could possibly be ignited by the fire.

6. If possible a dry chemical fire extinguisher

suppression system** on your machine.

There is not enough time available to read instructions during a fire emergency.

Ensure that all information necessary for you to immediately contact all sources of help (local fire department, etc) in the event of a fire emergency is recorded and readily available at all times.

1.24

or fire suppression system** should be used first to fight a machine fire.

Then immediately afterwards use the pressurized water hose supplied with the machine (if applicable) or a pressurized water extinguisher (if available). A fire suppressed by dry chemical may re-ignite from the heat retained by any debris or hot machine components in the area.

The water will cool the area, reducing the chances of re-ignition.

Tigercat 610E/615E Skidder •

Safety

Use the PASS method. This is the most effective use of a fire extinguisher.

•

•

•

•

WHAT TO DO AFTER A MACHINE FIRE HAS OCCURRED

Pull the pin at the top of the extinguisher that keeps the handle from being pressed.

Break the plastic seal as the pin is pulled.

•

Before returning the machine to work.

1. Ensure that the cause of the fire is determined and all appropriate repairs are completed.

Aim the nozzle at the base of the fire. Do not aim the nozzle at the flames. In order to put out the fire, you must extinguish the fuel, not the flames. Hose nozzles are often clipped to the extinguisher body.

Release the hose before taking aim.

2. Ensure that the fire detection system*

or the fire suppression system** is properly serviced and in working order (if applicable).

Squeeze the handle to release the pressurized extinguishing agent. The handle can be released at any time to stop the discharge.

3. Ensure that all extinguishers used in fighting the fire are replaced or recharged.

•

Sweep from side to side at the base of the fire until the fire is completely out or the fire extinguisher is empty

Notify your equipment dealer and / or Tigercat Industries Inc. by completing an incident report, Tigercat form number 5101.

*NOTE: Fire detection systems are offered by

Tigercat as an optional installation on some Tigercat product lines. Please disregard any references made to fire detection systems if not installed on your machine.

**NOTE: Dry chemical fire suppression systems

are offered by Tigercat as an optional installation on some Tigercat product lines. Please disregard any references made to fire suppression systems if not installed on your machine.

20229A

• • •

• •

TYPICAL FIRE EXTINGUISHER ACCESS HOLE

Place the nozzle of the fire extinguisher into the appropriate fire extinguisher access hole and discharge the extinguisher.

Only if you can safely do so, open the access panels to the machine in the area of the fire.

Failing all attempts to access the machine compartment, discharge the extinguisher through the mesh or any available openings on the machine.

Ensure that the machine and all components have cooled down sufficiently after a fire so that re-ignition does not occur.

Remain with the machine until help arrives.

1.25

Safety

Tigercat 610E/615E Skidder

DRY CHEMICAL CLEANUP PROCEDURES Both ABC dry chemical fire extinguishers and fire suppression systems discharge a chemical powder to extinguish the fire. The chemical makeup and the small particle size of the powder as well as the force of the discharge all contribute to the fire fighting capability. These same characteristics also permit the powder to penetrate into and fully cover all components in the vicinity of the discharge.

3. In areas exposed to heat during the fire, the dry chemical powder will melt forming a coating that cakes or crusts on all surfaces.

The following are recommendations for the cleanup and neutralizing of areas exposed to dry chemical powder.

Workers performing this work should wear protective clothing, safety goggles and a fine particle dust mask to minimize their personal exposure to the dry chemical powder.

Ensure that all electrical systems have been completely de-energized prior to any cleanup.

1. In areas of the machine that remained cool and dry during the fire, the dry chemical will stay in powder form.

Be certain to clean these areas immediately to prevent any settled residual powder from coming into contact with moisture whether through direct contact or humidity in the air.

Remove the powder residue by blowing off with air, sweeping, dusting or vacuuming using a HEPA filter capable of trapping the small dry chemical particles. Then wipe all surfaces with a damp cloth.

2. In areas exposed to moisture, the dry chemical powder will combine with water to form a paste that is mildly acidic. Note that all surfaces covered by this dry chemical paste including electrical contacts are vulnerable to corrosive attack.

To neutralize the acidic paste on large surfaces, spray or wash these areas with a mixture of 3 parts hot water to 1 part baking soda. Allow this mixture to stand for several minutes before rinsing with warm water. Wash the area with a mild soap and water solution.

Rinse thoroughly with water. Blow-dry to remove all residual water.

Cleaning of electrical contacts should be done using an electrical contact cleaner that has no flash or fire point and is non-corrosive and non-conductive such as CRC Contact Cleaner 2000.

1.26

To break down the caked dry chemical, spray or wash these areas with a 50/50 mixture of hot water and isopropyl alcohol. Allow this mixture to stand in place for several minutes.

The caked dry chemical when exposed to moisture is also mildly acidic. Therefore when the break down procedure has been completed, follow this immediately with the neutralizing procedure as described in step 2.

Tigercat 610E/615E Skidder

Safety NO RIDERS

SAFETY LABELS SAFETY LABELS CAB LABELS The following safety labels are installed in the cab of the Skidder. These labels are located inside the cab in full view of the operator. All labels must be periodically cleaned and inspected to ensure legibility is maintained. Replace any label that becomes illegible, damaged or removed.

EMERGENCY EXIT HAND TIGHTEN ONLY The sliding windows in the cab doors can be used as a third cab exit. The screens on the outside of these windows can be released by handles both on the inside and the outside of the cab. All handles should be hand tight only at all times.

This will prevent entrapment during an emergency by providing an exit point through the sliding windows if the cab doors are blocked. Refer also to EMERGENCY CAB EXITS in THIS SECTION.

NO RIDERS INSIDE OR OUTSIDE OF THE MACHINE . Do not carry passengers either in the cab or anywhere else on the machine. The vehicle seating accommodation is for one operator only.

Persons riding on the outside of the machine are subject to hazards such as falling off the machine, crush hazards, thrown object hazards and many other hazards WHICH COULD RESULT IN DEATH OR SERIOUS INJURY. If any person attempts to climb onto the machine during operation, STOP THE MACHINE IMMEDIATELY. Do Not Operate the machine until other personnel are a safe distance away from the machine.

1.27

Safety USE SEAT BELT

USE SEAT BELT. The seat belt supplied with this seat must be used at all times when operating this machine.

Tigercat 610E/615E Skidder READ OPERATOR'S MANUAL

READ OPERATOR'S MANUAL. Always read the operator’s manual before operating the machine.

Pay close attention to WARNINGS and HAZARD identifications.

Study all the safety messages in this manual and on the labels on the machine carefully.

1.28

Tigercat 610E/615E Skidder

Safety

OPERATOR'S MANUAL LOCATION

REMOVE IGNITION KEY BEFORE SERVICING THE MACHINE!

This label indicates the storage location of the operator's manual. This label is located on the outside of the operator's manual case inside the cab.

Prior to performing any service work or maintenance on the machine, stop the engine, REMOVE THE IGNITION KEY and store it in a safe place.

1.29

Safety

Tigercat 610E/615E Skidder

EXTERIOR LABELS

ARTICULATION LOCK

The following safety labels are installed on the exterior of this machine. These labels are located on the machine in the area where the specific safety concern is applicable. Labels must be periodically cleaned and inspected to ensure legibility is maintained. Replace any label that becomes illegible, damaged or removed.

REAR CHASSIS

RETAINING PINS

CRUSH HAZARD

620E-002

This label warns of the crush zone in the centre joint area. This can occur when the machine steering is used. DO NOT WORK IN THIS AREA UNTIL THE ARTICULATION LOCK BAR IS INSTALLED! Before working in the centre joint area, INSTALL THE CHASSIS ARTICULATION LOCK BAR between the chassis and centre joint to prevent accidental articulation which could result in death or serious injury.

630E-060

ARTICULATION LOCK STORED POSITION

ARTICULATION LOCK IN STRAIGHT LOCKED POSITION

Refer to ARTICULATION LOCK in SECTION 3 of THIS MANUAL for complete instructions.

630E-073

ARTICULATION LOCK IN ARTICULATED LOCKED POSITION

43304BUNI R0

1.30

Tigercat 610E/615E Skidder

Safety

CRUSH HAZARD

ENTANGLEMENT HAZARD

This label warns of the crush zone by a down force when the cab is in the partial tilt position. DO NOT WORK IN THIS AREA UNTIL THE CAB TILT SUPPORT LOCK IS IN PLACE! Before working under the cab when the cab is in the partial tilt position, be sure the CAB TILT SUPPORT LOCK is in place.

Never stand or work under an object supported with hydraulics. Always us‑e safety stands or a locking device.

Refer to TILTING THE CAB in SECTION 3 of THIS MANUAL for complete instructions.

36779BUNI R0

This label warns of an ENTANGLEMENT HAZARD (rotating parts) zone. The label is located on each side of the engine cooling fan which is near the engine serpintine drive belt.

DO NOT PLACE HANDS OR FINGERS IN THIS AREA. Rotating parts such as pulleys, belts and drives can cause entanglement of body parts resulting in serious injury.

KEEP HANDS AND FINGERS CLEAR OF ROTATING BELT, DRIVE OR PULLEY! Before performing any service work on these parts or in this area, shut engine off and wait for rotating parts to come to a complete stop.

1.31

Safety

Tigercat 610E/615E Skidder

KEEP CLEAR

DO NOT USE WINCH FOR HOISTING

43424BUNI R0

This label warns persons outside the cab to keep clear of the machine while in use.

Always keep clear of an operating machine.

When approaching an operating machine on foot, stay at least 60 m (200 feet) away until the operator recognizes your presence. Make sure that all equipment has been shut down before advancing to the machine.

Maintain a safe operating distance between the machine and workers and all other personnel. It is the duty of the operator to ensure that no person approach the machine while in use, the risk zone is 60 m (200 feet).

43225BUNI R0

This label warns of a crush zone by a down force if the winch is used as a hoist.

DO NOT use winch for hoisting.

The winch on this machine is intended only for use as a retrieval device.

Refer to OPERATING MACHINE – OPERATING and SKIDDING – CABLE SKIDDING in SECTION 2 of the OPERATOR'S MANUAL for instructions regarding the safe use and proper operation of the C.

Before moving machine, be sure all persons are clear of the area.

Always be alert for bystanders moving into the work area. Use horn to warn bystanders before moving the machine.

When using a signal person, keep the person in view at all times.

1.32

Tigercat 610E/615E Skidder

Safety

DO NOT LOOSEN RADIATOR FILL CAP UNTIL COOL

STORED ENERGY HAZARD

This label warns of a STORED ENERGY HAZARD. This label is located on the right side of the front chassis below the cab.

33952AUNI R0

This label warns of a PRESSURE AND FLUID SPRAY HAZARD when the coolant in the radiator is hot.

The machine is equipped with an accumulator.

The accumulator has stored hydraulic pressure.

Servicing the accumulator or any hydraulic components before releasing pressure could result in death or serious injury.

Turn the engine off. Only remove radiator fill cap when cool enough to touch with bare hands.

Slowly loosen cap to first stop to relieve pressure before removing completely.

DO NOT SERVICE ACCUMULATOR BEFORE RELEASING PRESSURE by applying brakes repeatedly with the engine OFF until there is no pedal resistance. This may take a minimum of 150 applications.

1.33

Safety FLUID SPRAY HAZARD

Tigercat 610E/615E Skidder EXPLOSION HAZARD

WARNING • EXPLOSION HAZARD. • DO NOT USE ETHER. • ENGINE EQUIPPED WITH HEATER STARTING AID. • USE OF ETHER COULD RESULT IN DEATH OR SERIOUS INJURY. 36782BENG R0

This label warns of a FLUID SPRAY HAZARD. This label is located above the pressurized water system fill plug.

The machine may be equipped with a pressurized water system. A water tank is incorporated into the dozer blade and is pressurized to 60 psi (4 bar).

Contact with fluid under pressure may cause injury.

This label warns of an EXPLOSION HAZARD. This label is located on the end of the air cleaner (air filter housing). The engine is equipped with a heater starting aid, DO NOT USE ETHER to assist in starting the engine.

USING ETHER COULD CAUSE AN EXPLOSION WHICH COULD RESULT IN DEATH OR SERIOUS INJURY.

DO NOT SERVICE PRESSURIZED WATER SYSTEM until air pressure is fully released by depressing the water system spray nozzle.

Tank fill plug has a cross drilled vent hole. Do not replace with standard plug.

Refer also to PRESSURIZED WATER SYSTEM MAINTENANCE in SECTION 3 of THIS MANUAL.

1.34

Tigercat 610E/615E Skidder

Safety

CRUSH HAZARD

HAND TIGHT ONLY - ALL HANDLES

This indicates that all handles should be hand tight only at all times.

This label warns of a CRUSH HAZARD. This label is located in the rear chassis control valve compartment.

This label is located on the screen protecting the sliding windows on both cab doors. The sliding windows in the cab doors can be used as a third cab exit. The screens on the outside of these windows can be released by handles both on the inside and the outside of the cab. Refer also to EMERGENCY CAB EXITS in THIS SECTION.

Movement of booms and cylinders could result in death or serious injury.

DO NOT perform work on valves or piping until boom and attachment are lowered to the ground and engine is shut off.

This label also located on the storage compartment on the left side of the dozer blade.

In a case where operator controls cannot be used to lower suspended machine elements due to an engine stall or other machine malfunction, suspended elements can be lowered manually.

Refer to DEPRESSURIZING SUSPENDED MACHINE ELEMENTS in SECTION 3 of THIS MANUAL.

1.35

Safety

Tigercat 610E/615E Skidder

FIRE PREVENTION!

PRESSURIZED WATER SYSTEM INSIDE HAND TIGHTEN ONLY

This label indicates the location of the pressurized water system (if equipped) and indicates that the compartment handle should be hand tight only at all times. This label is located on the outside of the pressurized water system compartment on the right side of the dozer blade.

READ UNDERSTAND AND FOLLOW THE FIRE PREVENTION GUIDELINES IN THIS MANUAL. These guidelines provide all the necessary action required to preventing fires on this machine. DO NOT OPERATE THIS MACHINE until you have read these instructions and have performed any necessary maintenance required that will prevent the potential of a fire from starting on this machine.

All handles should be hand tight only at all times.

This is particularly important for easy access to the pressurized water system in the event of a fire or other emergency. Refer also to FIRE PREVENTION in THIS SECTION.

It is also important to note that fire prevention inspections and maintenance MUST BE PERFORMED FREQUENTLY (several times per day). A clean combustible free machine as well as frequent inspections of the exhaust components, hydraulic hoses and electrical cables and performing any necessary repairs immediately will help prevent fires.

Maintain a CHARGED fire extinguisher on the machine at all times, know where it is and KNOW HOW TO USE IT! Refer also to FIRE PREVENTION in THIS SECTION.

1.36

Tigercat 610E/615E Skidder

Safety

FIRE EXTINGUISHER ACCESS HOLE

This label indicates the location of each FIRE EXTINGUISHER ACCESS HOLE. The label is installed on each fire extinguisher hole on the engine hood.

Refer also to FIRE PREVENTION in THIS SECTION.

1.37

Safety

Tigercat 610E/615E Skidder

1.38

Tigercat 610E/615E Skidder SECTION 2 - CONTROLS & OPERATION Read and understand the entire manual including Safety section prior to operating any equipment. Read and understand all manuals for any attachments or accessories.

CONTENTS - SECTION 2

ISSUE 2.0 MARCH 2015

ACCESS PANELS AND DOORS............................................................................................................. 2.86 ARTICULATION LOCK........................................................................................................................... 2.120 BATTERY DISCONNECT SWITCH......................................................................................................... 2.90 CAB CONTROLS..................................................................................................................................... 2.11 BRAKE PEDAL ROTATING SEAT & JOYSTICK STEERING..................................................................................... 2.11 STATIONARY SEAT & STEERING WHEEL.................................................................................... 2.12 COMPUTER DISPLAY......................................................................................................................... 2.24 CONTROL PANEL A/C HEATER CONTROLS - AIR CONDITIONER............................................................................. 2.21 A/C HEATER CONTROLS - AIR SOURCE....................................................................................... 2.21 A/C HEATER CONTROLS - FAN CONTROL................................................................................... 2.22 A/C HEATER CONTROLS - TEMPERATURE.................................................................................. 2.22 AUX (OPTIONAL)............................................................................................................................. 2.18 DIFFERENTIAL LOCK SELECTOR SWITCH................................................................................... 2.19 FAN CONTROL SWITCH, COOLING............................................................................................... 2.22 HORN, SAFETY ALERT - SWITCH.................................................................................................. 2.19 IGNITION SWITCH........................................................................................................................... 2.18 LIGHTS - SWITCH............................................................................................................................ 2.18 MAXIMUM SPEED CONTROL DIAL STATIONARY SEAT & STEERING WHEEL................................................................................. 2.18 PARKING BRAKE SWITCH.............................................................................................................. 2.19 WINCH CONTROL LEVER............................................................................................................... 2.21 WINCH SELECT SWITCH................................................................................................................ 2.20 DIFFERENTIAL LOCK SELECTOR SWITCH...................................................................................... 2.19 DIFFERENTIAL LOCK(S) ON/OFF SWITCH....................................................................................... 2.16 DIRECTION SELECTION SWITCH ROTATING SEAT & JOYSTICK STEERING..................................................................................... 2.13 DOZER BLADE CONTROL LEVER..................................................................................................... 2.15 DOZER GRAPPLE CONTROL LEVER................................................................................................ 2.15 ENGINE SPEED CONTROL, RIGHT JOYSTICK TRIGGER............................................................... 2.17 ENGINE SPEED/TRAVEL PEDALS ROTATING SEAT & JOYSTICK STEERING..................................................................................... 2.11 STATIONARY SEAT & STEERING WHEEL.................................................................................... 2.12 FOOT PEDALS, FORWARD FACING AND REAR FACING ROTATING SEAT & JOYSTICK STEERING..................................................................................... 2.11 BRAKE PEDAL.............................................................................................................................. 2.11 TRAVEL/ENGINE SPEED PEDAL................................................................................................ 2.11 HORN, SAFETY ALERT - SWITCH...................................................................................................... 2.19 IGNITION SWITCH............................................................................................................................... 2.18 INSTRUMENT PANEL.......................................................................................................................... 2.24 ALARM LIGHT.................................................................................................................................. 2.24 AUXILIARY POWER OUTLET.......................................................................................................... 2.25 COMPUTER DISPLAY...................................................................................................................... 2.24 COMPUTER USB PLUG................................................................................................................... 2.25 ENGINE DIAGNOSTICS CONNECTION.......................................................................................... 2.25

Controls and operation

Tigercat 610E/615E Skidder

LIGHTER...........................................................................................................................................2.25 MASTER ALARM.............................................................................................................................. 2.24 STORAGE COMPARTMENT............................................................................................................ 2.25 LEFT JOYSTICK (ROTATING SEAT & JOYSTICK STEERING) DIRECTION SELECTION SWITCH.................................................................................................. 2.13 MAXIMUM SPEED CONTROL......................................................................................................... 2.13 STEERING........................................................................................................................................2.12 MAXIMUM SPEED CONTROL ROTATING SEAT & JOYSTICK STEERING..................................................................................... 2.13 STATIONARY SEAT & STEERING WHEEL.................................................................................... 2.18 RIGHT JOYSTICK ARCH AND BOOM CONTROLS....................................................................................................... 2.16 BOOM AND ARCH CONTROLS....................................................................................................... 2.16 DIFFERENTIAL LOCK(S) ON/OFF SWITCH................................................................................... 2.16 GRAPPLE CONSTANT PRESSURE SWITCH................................................................................. 2.16 GRAPPLE OPEN/CLOSE................................................................................................................. 2.17 GRAPPLE ROTATE CONTROLS..................................................................................................... 2.16 TRIGGER SWITCH, ENGINE SPEED CONTROL........................................................................... 2.17 ROTATING SEAT KICK LEVER............................................................................................................ 2.26 SEAT.....................................................................................................................................................2.27 SEAT, ROTATING SEAT KICK LEVER................................................................................................. 2.26 STEERING JOYSTICK......................................................................................................................................... 2.12 STEERING WHEEL.......................................................................................................................... 2.14 TRAVEL/ENGINE SPEED PEDALS ROTATING SEAT & JOYSTICK STEERING..................................................................................... 2.11 STATIONARY SEAT & STEERING WHEEL.................................................................................... 2.12 WARNING MESSAGES................................................................................................. SEE COMPUTER WINCH CONTROL LEVER.................................................................................................................. 2.21 WINCH SELECT SWITCH.................................................................................................................... 2.20 CAB VENTILATION AIR VENTS...........................................................................................................................................2.82 FILTER, FRESH AIR............................................................................................................................. 2.82 FILTER, RECIRCULATING AIR, A/C UNIT........................................................................................... 2.82 CARE OF THE MACHINE...................................................................................................................... 2.114 CARE OF POLYCARBONATE WINDOWS........................................................................................ 2.114 CAUTIONS...................................................................................................................................... 2.116 CLEANING INSTRUCTIONS.......................................................................................................... 2.116 CONCEALING HAIRLINE SCRATCHES........................................................................................ 2.116 FIRE PRECAUTIONS..................................................................................................................... 2.117 GRAFFITI REMOVAL...................................................................................................................... 2.117 INSPECTION AND MAINTENANCE............................................................................................... 2.115 RESISTANCE TO CHEMICALS...................................................................................................... 2.115 RESISTANCE TO WATER.............................................................................................................. 2.115 CENTRE JOINT..................................................................................................................................... 2.110 CLEANING A/C CONDENSER AND COOLING ASSEMBLY................................................................ 2.118 COMPUTER.............................................................................................................................................2.28 ADJUSTMENT MENU EXAMPLE - ADJUSTMENT MENU NAVIGATION............................................................................ 2.38 ADJUSTMENT MENU - ENGINE SETTINGS...................................................................................... 2.34 AUTO RPM.......................................................................................................................................2.35 ENGINE HIGH IDLE ADJUST........................................................................................................... 2.34 WARM UP SPEED............................................................................................................................ 2.35 ADJUSTMENT MENU - FAN SETTINGS (IF EQUIPPED)................................................................... 2.35 CLEAN DURATION........................................................................................................................... 2.35 CLEAN FREQUENCY....................................................................................................................... 2.35 FAN AUTO CLEAN............................................................................................................................ 2.35 2.2

Tigercat 610E/615E Skidder

Controls and operation

ADJUSTMENT MENU - SERVICE SETTINGS.................................................................................... 2.36 FRONT TIRE SIZE............................................................................................................................ 2.36 HYDRAULIC OIL GRADE................................................................................................................. 2.36 PROGRAM MODE............................................................................................................................ 2.36 STEER ADJUST (JOYSTICK STEERING ONLY)............................................................................. 2.37 STEER INVERT (JOYSTICK STEERING ONLY)............................................................................. 2.37 COMPUTER CONTROL SYSTEM....................................................................................................... 2.29 COMPUTER CONTROL SYSTEM COMPONENTS............................................................................ 2.29 ENGINE COOLANT TEMPERATURE GAUGE.................................................................................... 2.32 ENGINE MENU - ENGINE FUNCTIONS.............................................................................................. 2.33 BOOST PRESSURE......................................................................................................................... 2.33 CHARGE AIR TEMPERATURE........................................................................................................ 2.32 COOLANT TEMPERATURE............................................................................................................. 2.32 ENGINE HOURS............................................................................................................................... 2.33 ENGINE OIL TEMPERATURE.......................................................................................................... 2.32 ENGINE VOLTAGE........................................................................................................................... 2.33 ENG % TORQUE.............................................................................................................................. 2.33 FUEL RATE....................................................................................................................................... 2.33 FUEL TEMPERATURE..................................................................................................................... 2.33 OIL PRESSURE................................................................................................................................ 2.33 ENGINE TACHOMETER GAUGE........................................................................................................ 2.33 HYDRAULIC OIL TEMPERATURE GAUGE......................................................................................... 2.41 INFORMATION MODE MENU.............................................................................................................. 2.40 DRIVE MOTOR SPEED.................................................................................................................... 2.41 DRIVE PRESSURE FORWARD....................................................................................................... 2.41 DRIVE PRESSURE REVERSE........................................................................................................ 2.41 HYDRAULIC OIL TEMPERATURE................................................................................................... 2.41 MACHINE HOURS............................................................................................................................ 2.41 SERIAL NUMBER............................................................................................................................. 2.41 TOTAL FUEL INFORMATION........................................................................................................... 2.42 TRANSMISSION TEMPERATURE................................................................................................... 2.42 TRAVEL SPEED............................................................................................................................... 2.41 TRIP FUEL INFORMATION.............................................................................................................. 2.42 MAIN MENU.........................................................................................................................................2.30 MAIN MENU PAGE............................................................................................................................... 2.42 MAIN MENU PAGE - ADJUST MENU.................................................................................................. 2.43 MAIN MENU PAGE - INFO MENU....................................................................................................... 2.49 LOGS................................................................................................................................................2.50 MODULES......................................................................................................................................... 2.50 MAIN MENU PAGE - MEASURE MENU.............................................................................................. 2.44 MAIN MENU PAGE - PREFERENCES MENU..................................................................................... 2.45 DATE/TIME ADJUSTMENT.............................................................................................................. 2.47 DISPLAY ADJUSTMENT.................................................................................................................. 2.46 LANGUAGE ADJUSTMENT............................................................................................................. 2.49 MD3 COMPUTER................................................................................................................................. 2.28 MD3 COMPUTER ELECTRONIC CONTROL & DISPLAY................................................................... 2.28 MD3 COMPUTER MAIN MENU........................................................................................................... 2.30 MESSAGES..........................................................................................................................................2.51 ALERT MESSAGES (YELLOW)....................................................................................................... 2.65 CRITICAL MESSAGES (RED)......................................................................................................... 2.52 ERROR MESSAGES (RED)............................................................................................................. 2.61 INFORMATION MESSAGES (BLUE)............................................................................................... 2.78

2.3

Controls and operation

Tigercat 610E/615E Skidder

MESSAGES - ALERT DIESEL EXHAUST FLUID < 5%....................................................................................................... 2.72 DIESEL EXHAUST FLUID LEVEL <10%.......................................................................................... 2.72 DIESEL EXHAUST FLUID LEVEL EMPTY....................................................................................... 2.72 DIESEL EXHAUST FLUID QUALITY................................................................................................ 2.73 DRIVE CHARGE FILTER BYPASSED.............................................................................................. 2.67 DRIVE CHARGE SYSTEM PRESSURE LOW................................................................................. 2.68 ENGINE AIR INTAKE FILTER RESTRICTED................................................................................... 2.67 ENGINE COOLANT TEMPERATURE HIGH.................................................................................... 2.71 ENGINE FAULT CODE MESSAGES - ALERT.................................................................................. 2.74 ENGINE VOLTAGE HIGH................................................................................................................. 2.71 ENGINE VOLTAGE LOW.................................................................................................................. 2.71 FUEL LEVEL LOW............................................................................................................................ 2.67 FUEL - WATER IN FUEL................................................................................................................... 2.71 HARDWARE FAILURE - COUT........................................................................................................ 2.70 HARDWARE FAILURE - DIN............................................................................................................ 2.70 HARDWARE FAILURE - DOUT........................................................................................................ 2.70 HARDWARE FAILURE - VIN............................................................................................................ 2.70 HARDWARE FAULT - MD3............................................................................................................... 2.69 HARDWARE FAULT - XA2................................................................................................................ 2.69 HARDWARE FAULT - XS2................................................................................................................ 2.69 MACHINE VOLTAGE HIGH.............................................................................................................. 2.68 MACHINE VOLTAGE LOW............................................................................................................... 2.67 MODULE HIGH SUPPLY VOLTAGE - ALERT.................................................................................. 2.76 MODULE HIGH TEMPERATURE - ALERT....................................................................................... 2.75 MODULE LOW SUPPLY VOLTAGE - ALERT................................................................................... 2.77 SERVICE BRAKE PRESSURE LOW............................................................................................... 2.68 MESSAGES - CRITICAL AFTERTREATMENT SYSTEM ENGINE IDLE TOO LONG............................................................. 2.58 AFTERTREATMENT SYSTEM TECHNICAL FAILURE.................................................................... 2.58 DRIVE MOTOR CLUTCH PRESSURE LOW................................................................................... 2.53 DRIVE MOTOR CLUTCH SLOW RESPONSE................................................................................. 2.55 DRIVE MOTOR OVERSPEED.......................................................................................................... 2.53 ENGINE COOLANT LEVEL LOW..................................................................................................... 2.57 ENGINE COOLANT TEMPERATURE HIGH.................................................................................... 2.57 ENGINE FAULT CODE MESSAGES - CRITICAL............................................................................. 2.60 ENGINE LOCKED OUT.................................................................................................................... 2.59 ENGINE OIL PRESSURE LOW........................................................................................................ 2.60 ENGINE OIL TEMPERATURE HIGH................................................................................................ 2.60 ENGINE RESTARTS REMAINING UNTIL ENGINE LOCKOUT....................................................... 2.59 ENGINE TORQUE DERATE ACTIVE............................................................................................... 2.58 HARDWARE FAULT - ENGINE......................................................................................................... 2.56 HARDWARE FAULT - MD3............................................................................................................... 2.56 HARDWARE FAULT - XA2................................................................................................................ 2.56 HARDWARE FAULT - XS2................................................................................................................ 2.56 HYDRAULIC OIL LEVEL LOW.......................................................................................................... 2.53 HYDRAULIC OIL TEMPERATURE HIGH......................................................................................... 2.54 INTERLOCK SYSTEM...................................................................................................................... 2.54 LH DRIVE MOTOR SPEED SENSOR FAULT.................................................................................. 2.55 RH DRIVE MOTOR SPEED SENSOR FAULT OR CLUTCH SLIP.................................................. 2.55 TRANSMISSION OIL TEMPERATURE HIGH.................................................................................. 2.54 MESSAGES - ERROR CURRENT OUTPUT ERROR (COUT)............................................................................................. 2.64 DIGITAL INPUT ERROR (DIN)......................................................................................................... 2.64 DIGITAL OUTPUT ERROR (DOUT)................................................................................................. 2.64 MODULE NO CONTACT ERROR.................................................................................................... 2.62 MODULE VREF ERROR.................................................................................................................. 2.63 2.4

Tigercat 610E/615E Skidder

Controls and operation

VOLTAGE INPUT ERROR (VIN)....................................................................................................... 2.64 MESSAGES - INFORMATION MACHINE STEERING INVERT DISABLED..................................................................................... 2.81 SETUP MODE - DRIVE MOTOR SETUP......................................................................................... 2.79 SETUP MODE - DRIVE PUMP POR SETUP................................................................................... 2.79 SETUP MODE - DRIVE PUMP REGULATION SETUP.................................................................... 2.79 SETUP MODE - ENGINE HP TEST.................................................................................................. 2.79 SETUP MODE - FUNCTION SETUP................................................................................................ 2.79 SETUP MODE - MAX CURRENT SETUP MODE............................................................................ 2.79 DIESEL EXHAUST FLUID (DEF) LEVEL WARNINGS............................................................................ 2.72 DIESEL EXHAUST FLUID (DEF) QUALITY WARNING.......................................................................... 2.73 DIESEL EXHAUST FLUID (DEF) TANK................................................................................................... 2.89 DOORS AND ACCESS PANELS............................................................................................................. 2.86 ENGINE AIR CLEANER AIR CLEANER...................................................................................................................................... 2.93 AIR CLEANER UNLOADER VALVE..................................................................................................... 2.93 AIR PRECLEANER.............................................................................................................................. 2.92 ENGINE FAULT CODE MESSAGES - ALERT......................................................................................... 2.74 ENGINE FAULT CODE MESSAGES - CRITICAL.................................................................................... 2.60 FIRE EXTINGUISHER, PORTABLE........................................................................................................ 2.83 FIRE PREVENTION FIRE EXTINGUISHER, PORTABLE..................................................................................................... 2.83 PRESSURIZED WATER SYSTEM....................................................................................................... 2.91 FUEL TANK..............................................................................................................................................2.88 FUSE AND RELAY PANELS CAB......................................................................................................................................................2.84 ELECTRICAL BOX............................................................................................................................... 2.85 HYDRAULIC FILL PUMP......................................................................................................................... 2.95 HYDRAULIC FILTERS............................................................................................................................. 2.94 HYDRAULIC OIL TANK............................................................................................................................ 2.94 MACHINE WARM UP OPERATION....................................................................................................... 2.102 MACHINE WARM UP SPEED ADJUSTMENT....................................................................................... 2.103 MOVING INSTRUCTIONS................................................................................. SEE SEPARATE BOOKLET OPERATING MACHINE........................................................................................................................... 2.95 CENTRE JOINT.................................................................................................................................. 2.110 MACHINE WARM UP OPERATION................................................................................................... 2.102 MACHINE WARM UP SPEED ADJUSTMENT................................................................................... 2.103 OPERATING GRAPPLE..................................................................................................................... 2.107 PRESTART CHECKS........................................................................................................................... 2.96 RESTARTING AN ENGINE THAT HAS RUN OUT OF FUEL............................................................. 2.106 STARTING ENGINE............................................................................................................................. 2.99 STARTING IN COLD WEATHER........................................................................................................ 2.101 STOPPING ENGINE........................................................................................................................... 2.105 SYSTEM TEST AND WARM UP........................................................................................................ 2.101 TRAVELLING WITHOUT A LOAD...................................................................................................... 2.106 PARKING BRAKE SWITCH..................................................................................................................... 2.19 PICTOGRAM DESCRIPTIONS.................................................................................................................. 2.7 PRESTART CHECKS............................................................................................................................... 2.96 RADIO, AM/FM CD................................................................................................................................... 2.83 RADIO, CB (IF EQUIPPED)..................................................................................................................... 2.83 RETRIEVAL POINTS............................................................................................................................. 2.121 ROTATING SEAT KICK LEVER............................................................................................................... 2.26 2.5

Controls and operation

Tigercat 610E/615E Skidder

SKIDDING.............................................................................................................................................. 2.110 CABLE SKIDDING.............................................................................................................................. 2.113 EFFECT OF ARCH/BOOM GEOMETRY ON WEIGHT DISTRIBUTION..........................................................................................................2.111 GRAPPLE SKIDDING........................................................................................................................ 2.112 SAFETY.............................................................................................................................................. 2.110 SKIDDING TECHNIQUE.................................................................................................................... 2.110 STARTING ENGINE................................................................................................................................. 2.99 STEERING JOYSTICK STEERING......................................................................................................................... 2.12 STEERING WHEEL.............................................................................................................................. 2.14 STEREO, AM/FM CD............................................................................................................................... 2.83 STOPPING ENGINE.............................................................................................................................. 2.105 SYSTEM TEST AND WARM UP............................................................................................................ 2.101 SYSTEM WARNING MESSAGES..................................................................................... SEE COMPUTER TILT CAB..............................................................................................................................SEE SECTION 3 TOWING INSTRUCTIONS - EHS TRANSMISSION.............................................................................. 2.125 TRANSMISSION DIPSTICK..................................................................................................................... 2.90 TRANSMISSION OIL FILL LOCATION.................................................................................................... 2.90 TRANSPORTING INSTRUCTIONS....................................................................................................... 2.122 LIFTING POINTS................................................................................................................................ 2.124 TIE DOWN POINTS............................................................................................................................ 2.123 WINCH, OPERATING............................................................................................................................ 2.108

2.6

Tigercat 610E/615E Skidder

Controls and operation

PICTOGRAM DESCRIPTIONS Diagrams in pictorial form are used to represent machine function operation. Some of the symbols are signs, characters, figures, or any components related to the operation of the machine. They are a simple universal language of symbols or pictograms that illustrate a function or component without the use of words. Pictograms are installed on or in close proximity to the switch or device used to activate or deactivate the machine function or they may be a sign used on a warning or indicator light of a function that is operating or advising of an alarm condition.

Examples of these pictograms are the turtle speed such as SLOW =

or FAST =

and the rabbit

that are often used to describe

.

The pictograms used on this machine are as follows: = Boom DOWN

= Adjustment Menu Icon

= Boom UP

= Air Conditioner ON OR

= Brake

= Air Conditioner OFF =Cigarette Lighter, 24 Volt = Air Source, Fresh Air = Control lever, multidirectional = Air Source, Recirculate = Control lever, dual direction = Alert Message Symbol

= Critical Message Symbol

= Arch IN

= Diesel Exhaust Fluid (DEF, AUS32, AdBlue)

= Arch OUT = Differential Locks (ON/OFF) = Auxiliary Power Outlet 12 V = Differential Lock, Front = Battery CONNECT / Voltage = Differential Locks, Front and Rear

= Battery DISCONNECT

= Differential Lock, Rear

2.7

Controls and operation

Tigercat 610E/615E Skidder

= Dozer Blade DOWN

= Engine Oil Temperature

= Dozer Blade UP

= Engine Run

= Dozer Grapple Close

= Engine Start

= Dozer Grapple Open

= Engine Stop

= Engine Speed Control

= Drive Motor Speed

= Engine Speed/travel

= Drive Pressure Forward

= Engine Speed

= Drive Pressure Reverse

= Engine Torque %

= Engine Boost Pressure

= Engine Wait to start

= Engine Charge Air Temperature

= Error Message Symbol

= Engine Coolant Temperature

= Foot Pedal Control

= Engine Fan, Variable Pitch, Full On

= Fuel Information, Total Usage = Engine Fan, Variable Pitch, Auto = Fuel = Engine Fan, Variable Pitch, Clean

= Fuel Diesel

= Engine Hours

= Fuel Reset / Trip Fuel Information

= Engine Menu Icon

= Grapple CLOSE

= Engine Oil Pressure = Grapple Constant Pressure

2.8

Tigercat 610E/615E Skidder

Controls and operation

P

= Grapple OPEN

= Parking Brake = Serial Number

= Grapple Rotate Clockwise

= Speed FAST or HIGH

= Grapple Rotate Counterclockwise

= Speed SLOW or LOW = Hand tighten only

= Steer Left

= Horn = Steer Left (Seat Forward Facing)

= Hydraulic oil level

= Steer Left (Seat Rear Facing)

= Hydraulic Oil Temperature

= Steer Right

= Imperial/Metric Toggle Symbol

= Information Menu Icon

= Steer Right (Seat Forward Facing)

= Information Message Symbol = Steer Right (Seat Rear Facing) = Lights, Work = Machine Hours

= Temperature

= Machine Warm Up

= Transmission Temperature (EHS)

= Maximum speed control

= Travel Direction

= OFF

= Travel Direction (Seat Forward Facing)

= ON = Travel Direction (Seat Rear Facing)

2.9

Controls and operation

Tigercat 610E/615E Skidder

= Travel FORWARD

= Travel FORWARD (Seat Forward Facing)

= Travel FORWARD (Seat Rear Facing)

= Travel REVERSE

= Travel REVERSE (Seat Forward Facing)

= Travel REVERSE (Seat Rear Facing)

= Travel Speed = Ventilation Blower Fan

= Volume, FULL

= Volume, EMPTY = Voltage / Battery CONNECT

= Winch = Winch Brake (Dynamic)

= Winch Freespool

= Winch IN

2.10

Tigercat 610E/615E Skidder

Controls and operation

IMPORTANT !

This manual is applicable to factory installed machine functions and controls. It does not take into account any changes or modifications made after shipment. Verify all functions before operating this machine.

CAB CONTROLS 2

1 2

620E-011

FORWARD FACING FOOT PEDALS (SEAT FACING FRONT OF MACHINE)

620E-014

1. TRAVEL/ENGINE SPEED PEDAL (ROTATING SEAT & JOYSTICK STEERING) Press the foot pedal to drive in the direction selected on the direction selection switch on the left joystick.

The position of the foot pedal is directly proportional to the travel/engine speed of the machine.

NOTE: A backup alarm will sound when travelling in reverse based on the position of the operator's seat.

Refer also to LEFT JOYSTICK – DIRECTION SELECTION SWITCH in THIS SECTION. 2. BRAKE PEDAL (ROTATING SEAT & JOYSTICK STEERING) Press the foot pedal to apply the hydraulic brakes in the front axle. This will also apply braking to the rear axle since they are mechanically locked together by the drive shafts and transmission.

NOTE: As a safety precaution before working on or around the machine; After the engine has been turned off, depress this pedal repeatedly until there is no pedal resistance to relieve any pressure that may be stored in the hydraulic system. This may take a minimum of 150 applications.

1

REAR FACING FOOT PEDALS (SEAT FACING REAR OF MACHINE)

Check service brake for proper operation daily.

Refer to SERVICE BRAKE – CHECKING BRAKE AND ACCUMULATOR FOR PROPER OPERATION in SECTION 3 of THIS MANUAL. FORWARD FACING PEDALS AND REAR FACING PEDALS (ROTATING SEAT & JOYSTICK STEERING) The rotating seat cab is equipped with two sets of pedals one set forward facing and the other set rear facing.

Note that control of machine travel is automatically transferred by the computer control system from the forward facing travel/engine speed pedal to the rear facing travel/engine speed pedal based on the position of the operator's seat. Both brake pedals operate regardless of seat position.

For safe operation of all controls the operator's seat must be locked in either the forward facing or rear facing position. Refer also to ROTATING SEAT KICK LEVER in THIS SECTION. FRONT AND REAR ORIENTATION NOTE: The dozer blade is considered to be at the front of the machine. The attachment is considered to be at the rear of the machine. Therefore in the forward facing position the operator's seat is facing the dozer blade and in the rear facing position the operator's seat is facing the attachment.

2.11

Controls and operation

Tigercat 610E/615E Skidder 5a

3

5b

4

620E-013

LEFT JOYSTICK

620E-029

3.

5. LEFT JOYSTICK

TRAVEL/ ENGINE SPEED PEDALS (STATIONARY SEAT & STEERING WHEEL)

(ROTATING SEAT & JOYSTICK STEERING)

Press the RIGHT foot pedal to drive FORWARD.

Steering Move the joystick to the RIGHT* to articulate the machine to the RIGHT* .

Press the LEFT foot pedal to drive in REVERSE.

Move the joystick to the LEFT* to articulate the machine to the LEFT* .

The position of the foot pedal is directly proportional to the travel/engine speed of the machine.

*NOTE: Steering control is automatically adjusted by the computer control system based on the position of the operator's seat. Therefore LEFT articulation and RIGHT articulation as described above are considered to be left and right as viewed by the operator either from the forward facing seat position or the rear facing seat position.

It should also be noted that the machine steering invert function can be disabled.

Refer to COMPUTER – MESSAGES INFORMATION – MACHINE STEERING INVERT DISABLED and COMPUTER – ADJUSTMENT MENU - SERVICE SETTINGS – STEER INVERT (JOYSTICK STEERING ONLY) in THIS SECTION.

NOTE: A backup horn will sound when travelling in reverse.

4. BRAKE PEDAL (STATIONARY SEAT & STEERING WHEEL) Depress the foot pedal to apply the hydraulic brakes in the front axle. This will also apply braking to the rear axle since they are mechanically locked together by the drive shafts and transmission.

NOTE: As a safety precaution before working on or around the machine; After the engine has been turned off, depress this pedal repeatedly until there is no pedal resistance to relieve any pressure that may be stored in the hydraulic system. This may take a minimum of 150 applications.

Check service brake for proper operation daily.

Refer to SERVICE BRAKE – CHECKING BRAKE AND ACCUMULATOR FOR PROPER OPERATION in SECTION 3 of THIS MANUAL.

2.12

This machine is equipped with variable ratio load sensing steering. The speed that the vehicle responds to the steering control input will vary, depending on the speed at which the steering control is moved.

When operating on the road, a slow movement of the steering control will not overcorrect and will steer a straight normal course.

Tigercat 610E/615E Skidder

Controls and operation 5b. MAXIMUM SPEED CONTROL (ROTATING SEAT & JOYSTICK STEERING) The maximum speed control allows the operator to set the maximum travel speed of the machine to maintain a given travel speed without having to feather the drive pedal.

FORWARD FACING SEAT

Push control forward to increase the maximum travel speed.

Pull control back to decrease the maximum travel speed of the machine.

This control can be used while the machine is in motion.

REAR FACING SEAT Operating in the woods requires quick steering changes and this is produced by a rapid movement of the steering control, which will quickly change the vehicle's direction.

For safe operation of all controls the operator's seat must be locked in either the forward facing or rear facing position. Refer also to ROTATING SEAT KICK LEVER in THIS SECTION. 5a. DIRECTION SELECTION SWITCH (ROTATING SEAT & JOYSTICK STEERING) This switch selects the direction of travel for the travel/engine speed pedal in use (either forward facing or rear facing).

This is a three position switch.

Place switch in the forward position to travel in a FORWARD* direction .

Place switch in the centre position for neutral.

Place switch in the rear position to travel in a REVERSE* direction . *NOTE: Control of machine travel is automatically transferred by the computer control system from the forward facing travel/ engine speed pedal to the rear facing travel/ engine speed pedal based on the position of the operator's seat. Therefore FORWARD and REVERSE as described above are considered to be forward and reverse as viewed by the operator either from the forward facing seat position or the rear facing seat position.

Refer also to FOOT PEDALS, FORWARD FACING AND REAR FACING – TRAVEL/ ENGINE SPEED PEDAL and ROTATING SEAT KICK LEVER in THIS SECTION.

2.13

Caution: Setting the maximum speed control to the minimum setting lowers maximum travel speed only, it will NOT prevent the machine from travelling when the forward or reverse travel controls are used.

Controls and operation 6. STEERING WHEEL

Tigercat 610E/615E Skidder

(STATIONARY SEAT & STEERING WHEEL) METERED STEER VALVE This machine is equipped with Variable Ratio Load Sensing Steering. The speed that the vehicle responds to the steering wheel input will vary, depending on the speed at which the steering wheel is moved.

When operating on the road, a slow movement of the steering wheel will not overcorrect and will steer a straight normal course.

Operating in the woods requires quick steering changes and this is produced by a rapid movement of the steering wheel, which will quickly change the vehicle's direction.

6

620E-030

The lever on the left side of the Steering Column allows the selection of Telescopic and Tilt options.

The horn button is located in the centre of the steering wheel.

QUICK STEER VALVE (OPTIONAL) This machine is equipped with Variable Ratio Load Sensing Steering. The speed that the vehicle responds to the steering wheel input will vary; depending on the angle the steering wheel is turned. Turning the steering wheel ±50° results in controlled flow, from zero to full steering flow.

When operating on the road, turning the steering wheel only a few degrees in either direction will result in slower steering, not overcorrect and will steer a straight normal course.

Operating in the woods requires quick steering changes and this is produced by fully turning the steering wheel (± 50°), which will fully lock steering and quickly change the vehicle’s direction.

The lever on the left side of the Steering Column allows the selection of Telescopic and Tilt options.

The horn button is located in the centre of the steering wheel.

2.14

Tigercat 610E/615E Skidder LOCATED TO THE RIGHT OF THE JOYSTICK ON THE RIGHT ARM REST

7

620E-023

Controls and operation

DOZER BLADE CONTROL LEVER

610E-001

7. DOZER BLADE CONTROL LEVER Pull the lever BACK to RAISE blade.

the dozer

Push the lever FORWARD to LOWER dozer blade.

8

7

DOZER CONTROL LEVERS

8. DOZER GRAPPLE CONTROL LEVER (OPTIONAL) Pull the lever BACK to OPEN grapple.

the

the dozer

Push the lever FORWARD to CLOSE dozer blade.

The control lever will return to the centre neutral position when released.

the

The control lever will return to the centre neutral position when released.

NOTE: Always travel with the dozer blade in the raised position to avoid obstacles.

NOTE: Always travel with the dozer blade in the raised position and grapple closed to avoid obstacles.

CAUTION Never use the dozer blade to remove tree stumps or large boulders.

WARNING When leaving the cab, always lower the grapple and dozer to the ground, engage the parking brake and turn the ignition switch off.

If leaving the Skidder unattended, also remove the ignition key and switch the battery disconnect switch to the OFF position .

2.15

Controls and operation

Tigercat 610E/615E Skidder 9b

9c

9a

9d

9. RIGHT JOYSTICK NOTE: Standard dual arch grapple skidder controls are shown. Non-standard machines or machines modified after shipment may use this joystick to control some other functions.

Always verify all functions before operating this machine.

9e

Boom Move the joystick BACK to RAISE boom.

620E-005

the

9

RIGHT JOYSTICK

9c Differential Locks ON/OFF - One push button (Top right - RIGHT BUTTON) This switch activates differential locks in the front, rear or both axles depending on the position of the differential lock selector switch on the control panel. Axle(s) are locked to provide torque to both wheels.

Move the joystick FORWARD to LOWER the boom.

Arch Move the joystick to the RIGHT to tilt arch OUT .

Press button to activate differential lock(s).

Move the joystick to the LEFT to tilt arch IN .

Push button a second time to deactivate.

The differential locks can be engaged or disengaged while the machine is in motion.

The differential lock icon on the main menu of the computer display will be illuminated when the front, rear or front and rear differential locks are engaged ( , or ).

9a Grapple Rotate - Two push buttons (Top left) Push LEFT BUTTON to rotate grapple COUNTERCLOCKWISE .

Push RIGHT BUTTON to rotate grapple CLOCKWISE .

This machine is equipped with a 10 minute AUTO-OFF feature which automatically deactivates the differential lock(s) after 10 minutes have passed.

9b Constant Pressure (grapple) - One push button (Top right - LEFT BUTTON) Push this button and release it to maintain a constant pressure HOLD on the grapple load and help prevent slipping. Constant pressure is released when the grapple is opened.

Refer also to CAB CONTROLS – CONTROL PANEL – DIFFERENTIAL LOCK SELECTOR SWITCH in THIS SECTION. IMPORTANT! Use differential locks sparingly and for brief periods and only when additional traction is needed or serious damage may occur.

The grapple constant pressure icon on the main menu of the computer display will be illuminated when the grapple constant pressure switch is activated.

Also refer to GRAPPLE, OPERATING in THIS SECTION.

2.16

Tigercat 610E/615E Skidder

Controls and operation

9d Grapple open/close - Two push buttons (Bottom) Push LEFT BUTTON to CLOSE grapple

.

Push RIGHT BUTTON to OPEN grapple

.

9e. Engine Speed Control - Trigger Pull this trigger to increase engine speed when performing machine functions which do not require machine travel. Release trigger to return to engine idle speed.

Refer also to COMPUTER – ADJUSTMENT MENU - ENGINE SETTINGS – AUTO RPM in THIS SECTION.

2.17

Controls and operation 1

2

6

Tigercat 610E/615E Skidder 3

4

7

54827B

5

8

12

9

13

14

10

15

11

16

CONTROL PANEL

CONTROL PANEL 1. IGNITION SWITCH - 3 POSITION STOP position - All electrical power fed through the ignition switch is turned "OFF" RUN position - Connects the battery to all functions. Used for normal machine operation.

6. MAXIMUM SPEED CONTROL DIAL (STATIONARY SEAT & STEERING WHEEL) The maximum speed control dial allows the operator to set the maximum travel speed of the machine to maintain a given travel speed without having to feather the drive pedals.

Turn the dial to the right to increase the maximum travel speed.

START position - This position energizes the starter motor and will crank over the engine.

Turn the dial to the left to decrease the maximum travel speed of the machine.

NOTE - Parking Brake must be ENGAGED to start the engine.

This control can be used while the machine is in motion.

Refer also to STARTING ENGINE in THIS SECTION.

Caution: Turning the maximum speed control dial completely to the left (minimum setting) lowers maximum travel speed only, it will NOT prevent the machine from travelling when the forward or reverse travel pedals are used.

2. LIGHTS FRONT - SWITCH This switch turns on working lights.

3. LIGHTS REAR - SWITCH This switch turns on working lights.

4. AUX (OPTIONAL) Applicable to optional light packages.

5. AUX (OPTIONAL) Applicable to optional light packages.

2.18

Tigercat 610E/615E Skidder

Controls and operation

7. PARKING BRAKE SWITCH P This is a three position switch which operates a driveline brake.

WARNING This machine is equipped with a controls safety interlock system. This system is intended to ensure machine functions are activated only when the operator is in the cab with the doors shut.

The interlock system prevents the machine from being driven and function controls from being operated while the parking brake is ENGAGED.

Momentarily press the top of this switch (ON) to ENGAGE the parking brake. The parking brake icon on the main menu of the computer display will be illuminated when the parking brake is engaged. The switch will spring return to the centre position.

Momentarily press the bottom of this switch (OFF) to DISENGAGE the parking brake. The switch will spring return to the centre position.

As part of the interlock system this machine automatically engages the parking brake whenever a cab door is open. This prevents accidental or improper operation of the controls from anywhere but the operator's seat.

In an emergency the parking brake can be engaged manually to slow down or stop the machine.

NOTE: The parking brake must be ENGAGED to START the engine, and DISENGAGED to DRIVE the machine.

SWITCH

Do not alter or bypass this safety feature.

Once the doors are shut and the parking brake is DISENGAGED the safety of both the operator and all persons outside the cab becomes the responsibility of the operator.

ACTUATOR ON DOOR

Do not allow machine controls to be activated without an operator in the cab.

620E-027

The parking brake, door interlock switches, and IQAN computer system interlock features are safety devices and must not be defeated in any way.

INTERLOCK SWITCHES ON CAB DOORS

NOTE ALSO: The interlock system prevents the machine from being driven and function controls from being operated while the parking brake is ENGAGED. As part of the interlock system this machine automatically engages the parking brake whenever a cab door is open. This prevents accidental or improper operation of the controls from anywhere but the operator's seat.

Always use this horn prior to starting the engine and to alert other personnel in the area of your presence.

9. DIFFERENTIAL LOCK SELECTOR SWITCH This is a three position switch,

/

/

.

Placing this switch in the (FRONT) position selects the front axle differential locks for activation via the differential lock switch on the right joystick.

Refer also to COMPUTER – MESSAGES CRITICAL – INTERLOCK SYSTEM in THIS SECTION.

Placing this switch in the (FRONT AND REAR) position selects both the front and rear axle differential locks for activation via the differential lock switch on the right joystick.

The parking brake must be kept properly adjusted at all times and should be serviced every 500 hours during normal operating conditions. Refer to PARKING BRAKE ADJUSTMENT in SECTION 3 of THIS MANUAL.

Placing this switch in the (REAR) position selects the rear axle differential locks for activation via the differential lock switch on the right joystick.

Refer also to CAB CONTROLS – DIFFERENTIAL LOCK(S) ON/OFF SWITCH in THIS SECTION.

8. HORN, SAFETY ALERT - SWITCH This is a two position "momentary" switch.

Press and hold this switch to sound the safety alert horn.

2.19

Controls and operation 1

2

6

Tigercat 610E/615E Skidder 3

4

7

5

12

8

9

14

10

15

11

16

CONTROL PANEL

54827B

10. WINCH SELECT SWITCH FOR CARCO WINCH

WARNING

This is a three position switch, O / I /

Place this switch in the O (OFF) position to de-activate the winch control lever and prevent accidental operation of the winch.

Place this switch in the I (ON) position to activate the winch control lever. The winch icon on the main menu of the computer display will be illuminated when the winch selector switch is in the I (ON) position.

Place this switch in the (FREESPOOL) position to disconnect the drive motor from the drum in the winch and allow the cable to be freely pulled from the spool by hand.

The freespool function is intended for use in pulling the cable by hand only and must not be used when the cable is loaded.

Improper use of the freespool function will result in damage to the winch.

13

When operating Carco winches the load MUST be removed from the cable before placing the winch control in the freespool position to avoid damage to the winch which could cause a safety hazard.

Attempting to engage or disengage the freespool function with a load on the cable will cause damage to clutch halves, piston, final planetary gearing and/or output shaft.

Damage to freespool components can cause a sudden loss of load control which could result in death or serious injury.

.

Free spool must be turned off to activate a pull with the winch. The winch freespool icon on the main menu of the computer display will be illuminated when the winch selector switch is in the position.

Refer also to WINCH CONTROL LEVER in THIS SECTION .

FOR ALLIED WINCH

This is a three position switch, O / I /

Place this switch in the O (OFF) position to de-activate the winch control lever and prevent accidental operation of the winch.

Place this switch in the I (ON) position to activate the winch control lever. The winch icon on the main menu of the computer display will be illuminated when the winch selector switch is in the I (ON) position.

2.20

.

Tigercat 610E/615E Skidder

Place the winch select switch (to the left of the lever) in the I (ON) position. Push and hold the winch control lever FORWARD to release the dynamic brake for dropping a load on the fly or drive away from a load with slight tension on the cable. The control lever will return to the centre neutral position when released.

The neutral or centre position actuates the winch pinion brake and prevents the drum from rotating.

Place the winch select switch (to the left of the lever) in the I (ON) position. Pull and hold the winch control lever BACK to wind in the winch cable . The control lever will return to the centre neutral position when released.

The dynamic brake position is not used for Allied Winch applications.

The neutral or centre position actuates the winch pinion brake and prevents the drum from rotating.

Place the winch select switch (to the left of the lever) in the I (ON) position. Pull and hold the winch control lever BACK to wind in the winch cable . The control lever will return to the centre neutral position when the handle is released.

Placing the winch select switch (to the left of the lever) in the (FREESPOOL) position permits the cable to unwind freely.

The cable can then be pulled from the drum by the operator.

Refer also to WINCH SELECT SWITCH in THIS SECTION.

Refer also to WINCH CONTROL LEVER in THIS SECTION .

FOR ALLIED WINCH

Place this switch in the (FREESPOOL) position to disconnect the drive motor from the drum in the winch and allow the cable to be freely pulled from the spool. Free spool must be turned off to activate a pull with the winch. The winch freespool icon on the main menu of the computer display will be illuminated when the winch selector switch is in the position.

11. WINCH CONTROL LEVER FOR CARCO WINCH

Controls and operation

12. AIR CONDITIONER This is a two position rocker switch used to turn the air conditioner ON or OFF. In the

position the air condition is ON.

In the

position the air conditioner is OFF.

13. AIR SOURCE This is a two position rocker switch used to add fresh air to the cab.

In the cab.

Placing the winch select switch (to the left of the lever) in the (FREESPOOL) position permits the cable to unwind freely. The cable can then be pulled from the drum by the operator by hand. The freespool function is intended for use in pulling the cable by hand only and must not be used when the cable is loaded.

Improper use of the freespool function will result in damage to the winch.

position fresh air is brought into the

In the position air from the cab is recirculated along with fresh air.

Refer also to CAB VENTILATION in THIS SECTION.

Refer also to WINCH SELECT SWITCH in THIS SECTION.

2.21

Controls and operation 1

2

6

Tigercat 610E/615E Skidder 3

4

7

5

8

12

9

13

14

10

15

11

16

CONTROL PANEL

54827B

14. TEMPERATURE CONTROL This is a variable, rotary control used to adjust the temperature of air in the cab for heating or air conditioning. The blue area of the scale indicates cooler temperatures the red area indicates warmer temperatures. Temperature is adjusted by regulating the flow of engine coolant into the heater core.

HOSE TO A/C HEATER UNIT

15. FAN CONTROL This is a rotary, four position switch (0/1/2/3).

When the switch is in the 0 position the cab air fan is OFF. When the switch is in the 1, 2 or 3 position the fan is activated at one of three fan speeds.

16. FAN CONTROL - SWITCH (IF EQUIPPED - VARIABLE PITCH FAN)

ENGINE

This is a three position switch, labeled / / (FULL ON/ AUTOMATIC/ CLEAN).

SHUT-OFF VALVE

This switch controls the operation of the optional Flexxaire® cooling fan.

The Flexxaire® cooling fan blade pitch is hydraulically varied to control the flow and direction of air through the cooling assembly

610E-002

AUTOMATIC Position - AUTOMATIC is the normal operating position for the fan control switch. When the switch is in the AUTOMATIC position, the fan will operate completely in an automatic mode. The computer control system will automatically control the fan pitch to minimize system energy losses and improve performance based on the temperature of the charge air, engine coolant and hydraulic oil. The computer system automatically adjusts fan air flow to the minimum required level to maintain optimal operating conditions.

HOT WATER SHUT-OFF VALVE

If the hot water shut-off valve is closed the temperature control will have no effect on cab air temperature for heating or cooling.

During times when cab heating is not required the hot water shut-off valve, on the heater hose from the engine, may also be closed to prevent hot water from seeping through the heater unit, thereby reducing the cooling effect.

2.22

Tigercat 610E/615E Skidder

Controls and operation

Automatic control of fan air flow to match your operating conditions can lower fuel consumption and reduce operating costs. In high temperature operating conditions the fan air flow is increased to improve cooling ability and efficient operation of the cooling assembly and air conditioning systems. In low temperature operating conditions fan air flow is reduced, as less cooling is required for efficient operation of the cooling assembly.

When the CLEAN cycle is complete the fan automatically returns to normal air flow direction.

The auto clean cycle is adjustable through the computer control system menu (ADJUSTMENT MENU – FAN SETTINGS).

Refer also to COMPUTER – ADJUSTMENT MENU - FAN SETTINGS in THIS SECTION. It is also important to manually clean debris from the machine on a regular basis to maintain low machine operating temperatures.

Refer to CLEANING A/C CONDENSER AND COOLING ASSEMBLY in THIS SECTION.

In addition, when this switch is in the AUTOMATIC position, the system will automatically cycle through an auto clean cycle.

The auto clean cycle is adjustable through the computer control system menu (ADJUSTMENT MENU – FAN SETTINGS).

Refer also to COMPUTER – ADJUSTMENT MENU - FAN SETTINGS in THIS SECTION. Note that when the switch is in the AUTOMATIC position and the fan has stopped due to low charge air, engine coolant and hydraulic oil temperatures, turning ON the A/C will cause the computer system to immediately place the fan blades at a pitch to provide 30% air flow. This is to ensure that sufficient air flow is available for the cab A/C even while the machine is still warming up.

FULL ON Position - When the switch is in the FULL ON position, the computer control system is overridden and the fan will run at FULL air flow (blades pitched to 100%), for cooling regardless of charge air, engine coolant or hydraulic oil temperatures.

Normally the fan control switch is placed in the AUTOMATIC position for optimal cooling.

The FULL ON position is intended for use in the event of a temporary failure of the control system.

CLEAN Position - Momentarily pressing the switch to the CLEAN position will manually start the automatic clean cycle, reversing the flow of air (there is no need to hold the switch down). The pitch of the fan blades is changed and the direction of airflow through the engine enclosure is reversed. This change in airflow blows debris from the machines engine enclosure to eliminate potential overheating and poor machine performance caused by overheating. Ensure that there are no personnel standing directly to the sides of the machine when performing this operation, as dust and debris will fly out.

2.23

Controls and operation

Tigercat 610E/615E Skidder 2

1

3

4

5

7 56583BUNI

6

8

INSTRUMENT PANEL

INSTRUMENT PANEL

2. ALARM LIGHT This light flashes to alert the operator that an alarm condition has been detected and should be dealt with immediately. All warning messages can be viewed on the computer display on the instrument panel.

1. COMPUTER DISPLAY The computer display is the operator interface with the computer control system.

Refer to COMPUTER in THIS SECTION for complete operating details.

Refer to the COMPUTER – MESSAGES in THIS SECTION. 3. MASTER ALARM This alarm will sound to alert the operator that an alarm condition has been detected and should be dealt with immediately. All warning messages can be viewed on the computer display on the instrument panel. Refer to the COMPUTER – MESSAGES in THIS SECTION.

2.24

Tigercat 610E/615E Skidder

Controls and operation

4. LIGHTER 24V Cigarette lighter is supplied.

IMPORTANT 24 VOLT ELECTRICAL SYSTEM 5. AUXILIARY POWER OUTLET 12 V A 12 volt outlet is provided for portable devices such as cell phones.

6. STORAGE COMPARTMENT 7

630D-04X

8

REMOVE COVER TO ACCESS

7. COMPUTER USB PLUG Plug in a laptop with appropriate IQAN software for software updates, diagnostics and some adjustments.

Refer also to COMPUTER in THIS SECTION and SECTION 6 of the SERVICE MANUAL for more information.

8. ENGINE DIAGNOSTICS CONNECTION Plug a remote electronic diagnostic device into this connection such as a lap-top computer with appropriate engine manufacturer's programming to perform engine performance analysis and tuning.

NOTE: This operation can only be performed by a trained service technician.

2.25

Controls and operation ROTATING SEAT KICK LEVER

(ROTATING SEAT & JOYSTICK STEERING)

620E-024

Tigercat 610E/615E Skidder FRONT AND REAR ORIENTATION NOTE: The dozer blade is considered to be at the front of the machine. The attachment is considered to be at the rear of the machine. Therefore in the forward facing position the operator's seat is facing the dozer blade and in the rear facing position the operator's seat is facing the attachment.

ROTATING SEAT KICK LEVER

This lever releases the seat to rotate between forward facing position and the rear facing position.

To rotate from the forward facing position to the rear facing position kick the left side of the lever and rotate the seat to the right until the seat locks in the rear facing position.

To rotate from the rear facing position to the forward facing position kick the right side of the lever and rotate the seat to the left until the seat locks in the forward facing position.

For safe operation of all controls the operator's seat must be locked in either the forward facing or rear facing position. A limit switch located in the seat pedestal sends a signal to the computer control system indicating the position of the operator's seat.

Note that control of machine travel is automatically transferred by the computer control system from the forward facing pedal to the rear facing pedal based on the position of the operator's seat. Both brake pedals operate regardless of seat position.

Refer also to FOOT PEDALS, FORWARD FACING AND REAR FACING – TRAVEL/ ENGINE SPEED PEDAL and LEFT JOYSTICK – DIRECTION SELECTION SWITCH in THIS SECTION. Note that steering control is automatically adjusted by the computer control system based on the position of the operator's seat. Refer also to LEFT JOYSTICK – STEERING in THIS SECTION. It should also be noted that the machine steering invert function can be disabled. Refer to COMPUTER – MESSAGES - INFORMATION – MACHINE STEERING INVERT DISABLED and COMPUTER – ADJUSTMENT MENU - SERVICE SETTINGS – STEER INVERT (JOYSTICK STEERING ONLY) in THIS SECTION. 2.26

Tigercat 610E/615E Skidder OPERATOR’S SEAT - AIR RIDE ADJUSTMENTS

Controls and operation SEAT ADJUSTMENTS

WARNING The seat belt supplied with this seat must be used at all times when operating this machine.

LUMBAR HORIZONTAL ADJUSTMENT (NOT SHOWN)

AIR RIDE ADJUSTMENT PROCEDURES The ride adjustment can be made by pulling or pushing the air ride control valve knob.

BACK ANGLE ADJUSTMENT

To stiffen the air ride For a stiffer ride push on the air ride adjustment knob to increase the air pressure in the suspension air bag.

To soften the air ride For a softer ride, pull on the air ride adjustment knob to decrease the air pressure in the suspension air bag.

2-WAY ADJUSTABLE LUMBAR To increase lumbar support pressure, turn lumbar adjustment control clockwise. To decrease lumbar support pressure, turn lumbar adjustment lever counterclockwise

RIDE ADJUSTMENT KNOB

FORE/AFT SLIDE LEVER

620E-040

BACKREST - ANGLE ADJUSTMENT Rotate backrest angle adjustment control to place backrest at the desired angle.

LUMBAR HORIZONTAL ADJUSTMENT

SEAT - HORIZONTAL POSITION Move and hold fore/aft slide lever. Roll seat forwards or backward to the desired position relative to the foot pedal controls.

ARMREST ADJUSTMENT Each armrest has 2 adjustments to place it in the desired position. Loosen adjustment knobs to reposition armrest height and fore/aft position.

ARMREST ADJUSTMENT

VIEW FROM RIGHT REAR OF SEAT

620E-042

HEIGHT ADJUSTMENT PROCEDURES This seat is equipped with a fixed (bolted) two position height adjustment. The second position provides a total height increase of 1". Four bolts are used to reposition the seat for height adjustment.

HEIGHT ADJUSTMENT BOLTS (4)

HEIGHT ADJUSTMENT

2.27

Controls and operation

Tigercat 610E/615E Skidder MD3 COMPUTER

COLOUR DISPLAY

MD3 COMPUTER, ELECTRONIC CONTROL AND DISPLAY

630E-301A

MD3 COMPUTER ELECTRONIC CONTROL & DISPLAY

MD3 COMPUTER USB PLUG

ALARM MD3 COMPUTER LIGHT

MASTER ALARM

The MD3 computer, electronic control and display is the operator interface with the electronic control system. The MD3 is the central unit in the control system which works as both a master controller and a display unit. It has a backlit colour graphic transflective display for reading system information.

The front of the MD3 consists of a control panel with a display and nine buttons. The buttons are arranged on the bottom and right hand side of the display.

• F1 through F4 function buttons

,

,

, .

Programmed buttons that are configured by program software to bring up a display page, bring up an adjustment group or act as an input.

• Up and down arrow buttons

,

.

Navigation buttons that are used to scroll through selections on a menu page. The buttons are configured by program software to bring up a display page, bring up an adjustment group or act as a virtual input.

• OK button

INSTRUMENT PANEL Pushing this button equals ’enter’. Saves the value or confirms the selection you have made.

• Menu button .

Always brings up the Menu page. It is not programmable.

• ’Esc’ or BACK button

.

Returns you to the previous display page. May be configured by program software to bring up a display page, bring up an adjustment group or act as a virtual input.

.

2.28

Tigercat 610E/615E Skidder MD3 COMPUTER MODULE

Controls and operation XA2-A1 EXPANSION MODULE FRONT CHASSIS 2

XS2 EXPANSION MODULE CAB

XA2-A0 EXPANSION MODULE FRONT CHASSIS

ENGINE DIAGNOSTIC CONNECTOR

ENGINE ELECTRONIC CONTROL UNIT MODULE

630E-002X

COMPUTER CONTROL SYSTEM COMPONENTS

COMPUTER CONTROL SYSTEM The MD3 computer control system is part of a network of components (shown above). The system is made up of the following components: • • • • • •

LOCATED IN CAB BEHIND LEFT KICK PANEL

MD3 Computer and Display Module XS2 Expansion Module (Cab) XA2-A1 Expansion Module (Front Chassis 2) XA2-A0 Expansion Module (Front Chassis) Engine Electronic Control Unit Module (Tigercat/FPT NEF 6.7L) Various controls, switches, sensors and valves not shown.

The MD3 computer is the main controller in the system. The MD3 computer program is the operating system for the computer display as well as the control system for the machine operating parameters.

620E-043

The engine electronic control unit module provides electronic information to the MD3 computer via the J1939 CAN BUS link. This information is displayed on the computer display.

XS2-A0 MODULE - CAB

LOCATED UNDER CAB, RIGHT REAR - REMOVE COVER TO ACCESS MODULES

NOTE: The computer control system is softwarebased. This software may be updated after the machine is in service as a part of on-going product improvement programs and service newsletters.

The information contained in this manual is accurate at the time of printing. Improvements to the machine and/or software are on-going and may not be covered. In these cases contact your Tigercat dealer for appropriate information.

XA2-A0 FRONT CHASSIS

XA2-A1 FRONT CHASSIS 2

615C-007

2.29

XA2 MODULES

Controls and operation 1

2A 2B

Tigercat 610E/615E Skidder 3

4A

4B

5

15 14 13 12 6

7

8

9

10

11

MAIN MENU

630E-301

MD3 COMPUTER MAIN MENU 1. ** PARKING BRAKE - ENGAGED/DISENGAGED

11. ALARM INDICATORS - Press F4 to select 12. HYDRAULIC OIL GRADE INDICATOR

2A. ** REAR DIFFERENTIAL LOCK - ENGAGED/DISENGAGED

13. HYDRAULIC OIL TEMPERATURE GAUGE*** 14. DEF LEVEL INDICATOR

2B. ** FRONT DIFFERENTIAL LOCK - ENGAGED/DISENGAGED

15. FUEL LEVEL GAUGE****

3. *GRAPPLE CONSTANT PRESSURE ON/OFF

* When the icon is illuminated, function is ON.

4A. * WINCH ON/OFF (

** When the icon is illuminated, function is ENGAGED.

)

4B. * WINCH FREE SPOOL (

)

*** Note that gauge symbol colour changes indicate temperature range (blue=low, white=normal, red=high)

5. * MACHINE WARM UP ON/OFF 6. ENGINE TACHOMETER GAUGE 7. ENGINE MENU - Press F1 to select

**** Note yellow fuel symbol indicates fuel level low.

8. ADJUSTMENT MENU - Press F2 to select 9. ENGINE COOLANT TEMPERATURE GAUGE*** 10. INFORMATION MENU - Press F3 to select 2.30

Tigercat 610E/615E Skidder

Controls and operation

ENGINE MENU

The engine functions on display are as follows: Charge Air Temperature - °F or °C From the main menu press the F1 button to select the engine display.

Engine Coolant Temperature - °F or °C Engine Oil Temperature - °F or °C

When selected the engine menu icon is on display and the engine functions will also be displayed.

Fuel Temperature - °F or °C Engine Speed - rpm Turbocharger Boost Pressure - psi or bar Engine Oil Pressure - psi or bar Engine Torque - % Engine Hours - h Voltage - V Fuel Rate - US gph or L/h (instantaneous)

2.31

Controls and operation

Tigercat 610E/615E Skidder 1.

Charge Air Temperature (°F or °C) This display indicates the charge air cooler temperature reading.

If temperature rises above the recommended temperature, alarm will sound, check the following:

• Plugged air intake access panel screens • Plugged charge air cooler.

DO NOT continue to operate machine.

Refer to CLEANING A/C CONDENSER AND COOLING ASSEMBLY in THIS SECTION. Refer also to the COMPUTER – MESSAGES in THIS SECTION.

ENGINE FUNCTIONS Press the F1 button to toggle the machine warm up function ON/OFF. Refer to MACHINE WARM UP OPERATION and MACHINE WARM UP SPEED ADJUSTMENT in THIS SECTION.

2.

Engine Coolant Temperature (°F or °C) This display indicates the current engine coolant temperature.

If temperature rises above the recommended temperature, alarm will sound, check the following:

Press the F2 button to toggle between metric and imperial units of measure.

• Plugged air intake access panel screens • Plugged radiator.

Press the back button to return to the main menu.

DO NOT continue to operate machine.

Refer to CLEANING A/C CONDENSER AND COOLING ASSEMBLY in THIS SECTION.

NOTE: Coolant temperature can also be monitored using the engine coolant temperature gauge shown on the main menu.

Note also that gauge symbol colour changes indicate temperature range (blue=low, white=normal, red=high) Refer also to the COMPUTER – MESSAGES in THIS SECTION. 3.

Engine Oil Temperature (°F or °C) This display indicates the current engine oil temperature.

If temperature rises above the recommended temperature, alarm will sound, check the following:

• Plugged air intake access panel screens • Plugged radiator.

DO NOT continue to operate machine.

2.32

Tigercat 610E/615E Skidder Refer to CLEANING A/C CONDENSER AND COOLING ASSEMBLY in THIS SECTION.

Controls and operation 8.

This display indicates the percentage of maximum engine peak torque currently in use.

Refer also to the COMPUTER – MESSAGES in THIS SECTION. 4.

With engine speed at IDLE (no load) and hydraulic oil at operating temperature the reading should be:

Fuel Temperature - °F or °C This display indicates the fuel temperature.

5.

Parking Brake ENGAGED 6-10%

Engine Speed (rpm)

Readings with the parking brake DISENGAGED should be 10-14%.

This display indicates engine speed in rpm.

Maintaining Correct Engine RPM

If the readings are outside this range investigate the cause.

It is important that the engine speeds be correct at all times:

NOTE: The above readings are at normal operating temperatures. During cold start-ups it is not unusual for readings to be significantly higher until normal operating temperatures are reached.

FPT N67 Engine: Low Idle 950 RPM (No Load) High Idle 2200 RPM (No Load)* NOTE: The above values are measured with the hydraulic and engine oil at normal operating temperatures and no functions activated.

Engine idle speed defaults to 950 rpm when the engine is started.

Eng % Torque (%)

9.

Engine Hours - h This display indicates the total number of hours the engine has run.

10.

Engine Voltage (volts) This display indicates engine voltage levels.

Normal operating range for the electrical system is between 20 and 30 volts.

If engine voltage goes outside the normal range, an alarm will sound. Refer to COMPUTER – MESSAGES in THIS SECTION. A reading in excess of 30 volts indicates a possible faulty voltage regulator.

NOTE ALSO: Engine speed can also be monitored using the engine tachometer gauge shown on the main menu.

A reading less than 20 volts indicates a possible faulty battery or alternator.

* Refer also to COMPUTER – ADJUSTMENT MENU - ENGINE SETTINGS – ENGINE HIGH IDLE ADJUST and AUTO RPM in THIS SECTION. 6.

Boost Pressure (psi or bar) This display indicates air intake manifold boost pressure in psi.

7.

IMPORTANT 24 VOLT ELECTRICAL SYSTEM 11.

Fuel Rate -US gph or L/h(instantaneous) This display indicates the current rate of fuel consumption in gallons per hour.

Oil Pressure (psi or bar) This display indicates engine oil pressure.

If oil pressure falls too low, an alarm will sound.

Refer to the COMPUTER – MESSAGES in THIS SECTION.

2.33

Controls and operation

Tigercat 610E/615E Skidder

ADJUSTMENT MENU

ENGINE SETTINGS From the main menu press F2 button to select the ADJUSTMENT MENU. When selected the adjustment menu icon is on display and all the adjustment selections will also be displayed.

Press the F1 button to select the Engine Settings Menu from the ADJUSTMENT MENU. The engine settings menu will appear.

Press F1 (Adjust) to adjust engine settings.

Press the back button to return the Engine Settings Menu display.

Press the back button again to return to the main menu.

The adjustable engine settings are: Engine High Idle Adjust Range 1800 to 2200* rpm This parameter allows the operator to adjust engine high idle speed limit, this limit will be in effect whenever the grapple constant pressure function is NOT activated. This function is intended to allow the automatic reduction of the engine high idle speed limit when travelling without a load.

The adjustment selections are as follows: •

Engine Settings - Shown first by default.

•

Fan Settings - Press F2 to select

•

Service Settings - Press F3 to select Press the back button to return to the main menu.

2.34

Tigercat 610E/615E Skidder

Controls and operation

Auto RPM 2200 rpm* Off 2000 rpm 1800 rpm 1600 rpm When the Auto RPM function is set to the default setting of 2200 rpm the engine speed will automatically increase proportionally with operation of all joystick functions to a maximum of 2200 rpm. Note that if the engine high idle adjust setting is lower than the Auto RPM setting engine speed will be limited to the lower speed setting.

The Auto RPM function can also be set to 2000 rpm, 1800 rpm or 1600 rpm.

FAN SETTINGS (IF EQUIPPED)

When the Auto RPM function is OFF engine rpm must be increased by the operator using the travel/engine speed pedals or the engine speed control trigger on the right joystick.

Press F2 button to select Fan Settings Menu from the ADJUSTMENT MENU. Note that this menu is applicable only for machines equipped with the optional variable pitch fan.

Warm Up Speed Range 950 to 1500 rpm (1200* rpm) * NOTE: Reset default settings are marked.

The fan settings menu will appear.

Press F2 (Adjust) to adjust fan settings Press the back button to return the Fan Settings Menu display.

Refer also to MACHINE WARM UP OPERATION and MACHINE WARM UP SPEED ADJUSTMENT in THIS SECTION. Refer to COMPUTER – ADJUSTMENT MENU – EXAMPLE – ADJUSTMENT MENU NAVIGATION for an example of adjustment menu navigation.

Press the back button again to return to the main menu.

The adjustable fan settings are: Fan Auto Clean On* or Off Clean Frequency Range 1 to 420 minutes (*30 minutes) Clean Duration Range 5 to 20 seconds (*15 seconds) * NOTE: Reset default settings are marked.

Refer to COMPUTER – ADJUSTMENT MENU – EXAMPLE – ADJUSTMENT MENU NAVIGATION for an example of adjustment menu navigation.

2.35

Controls and operation

Tigercat 610E/615E Skidder Refer also to COMPUTER – MESSAGES - CRITICAL – HYDRAULIC OIL TEMPERATURE HIGH in THIS SECTION for more information about the hydraulic oil temperature warning.

Refer to COMPUTER – INFORMATION MODE MENU – HYDRAULIC OIL TEMPERATURE in THIS SECTION for hydraulic oil temperature information display.

Front Tire Size Not Configured 28L 24.5 30.5L 35.5L DH73

SERVICE SETTINGS Press F3 button to select the Service Settings Menu from the ADJUSTMENT MENU.

This information is used by the machine program to accurately calculate and display machine travel speed.

The service settings menu will appear.

Press F3 (Adjust) to adjust service settings

Program Mode Normal* Engine HP Test Mode Drive Motor Setup Mode Drive Pump POR Setup Mode Drive Pump Regulation Setup Function Setup Mode Max Current Setup Mode (if equipped)

Press the back button to return the Service Settings Menu display.

Press the back button again to return to the main menu.

The adjustable service settings are: Hydraulic Oil Grade ISO 22* Petro CAN MV 22 ISO 32 Petro CAN MV 36 ISO 46 Esso Univis Ultra 46 Petro CAN MV 60 ISO 68 This information is used by the machine program to adapt hydraulic oil temperature warning messages for the operating range of each Hydraulic Oil Grade.

* NOTE: Reset default settings are marked.

Refer to COMPUTER – ADJUSTMENT MENU – EXAMPLE – ADJUSTMENT MENU NAVIGATION for an example of adjustment menu navigation.

IMPORTANT !

Machine must be in the Normal Program Mode to operate normally.

Other program modes are used for service/setup procedures only.

When setup program modes are chosen an information message is shown on the electronic display until the message is acknowledged.

In each program mode some controls are deactivated for safety during setup procedures.

Attempting to use these controls will reactivate the information message.

Hydraulic oil grade information is shown on the main menu below the hydraulic oil temperature gauge.

Refer also to APPROVED HYDRAULIC OILS in SECTION 3 of THIS MANUAL for hydraulic oil operating range information.

2.36

Tigercat 610E/615E Skidder

Controls and operation

Steer Adjust (Joystick steering only) Range 50 to 100% (75*%) This setting adjusts the performance of the joystick steering function. A lower setting will result in a slower response. A higher setting will result in a quicker response.

Steer Invert (Joystick steering only) On* or Off When ON the joystick steering control is automatically adjusted by the computer control system based on the position of the operator's seat. Therefore LEFT articulation and RIGHT articulation are considered to be left and right as viewed by the operator either from the forward facing seat position or the rear facing seat position.

When OFF the joystick steering invert function is disabled. Steer joystick direction does not change when operator is facing rearward.

Therefore LEFT articulation and RIGHT articulation are considered to be left and right as viewed by the operator from the forward facing seat position regardless of the position of the operator's seat. The machine steering invert disabled information message will be shown each time the machine is started to inform the operator that the steer invert function has been disabled.

Refer also to LEFT JOYSTICK – STEERING, ROTATING SEAT KICK LEVER and COMPUTER – MESSAGES - INFORMATION – MACHINE STEERING INVERT DISABLED in THIS SECTION.

2.37

Controls and operation

Tigercat 610E/615E Skidder

EXAMPLE – ADJUSTMENT MENU:

From the main menu press F2 button to select the ADJUSTMENT MENU.

Press the arrow up or arrow down buttons to scroll to the setting to be adjusted.

Press the F2 button to reset to default setting.

Press F2 (Yes) or F3 (No) to confirm.

The engine settings menu will appear by default.

Press F1 (Adjust) to adjust engine settings

2.38

Tigercat 610E/615E Skidder

Controls and operation

OR

OR

Press the OK button to go to the adjustment display.

To reset to default setting press the F2 button.

Press F2 (Yes) or F3 (No) to confirm.

Press the arrow up or arrow down buttons to make the adjustment.

Press the OK button to confirm the setting.

Press the back button to return to the adjustment menu.

Press the back main menu.

2.39

button again to return to the

Controls and operation

Tigercat 610E/615E Skidder

INFORMATION MODE MENU

The information functions on display are as follows: Drive Pressure Forward - psi or bar

Press the F3 button to access the information menu.

Drive Pressure Reverse - psi or bar

When selected the information menu icon is on display and the information functions will also be displayed.

Travel Speed - mph or km/h Drive Motor Speed - rpm Serial Number Machine Hours - h Hydraulic Oil Temp -°F or °C Transmission Temperature -°F or °C Total fuel information Trip fuel information Press the F1 button to reset the trip average fuel rate and trip fuel used functions.

Press the F2 button to toggle between imperial and metric units of measure.

Press the back button to return to the main

2.40

Tigercat 610E/615E Skidder

Controls and operation • • • • • •

Plugged oil cooler Malfunction in a hydraulic system High loads on the hydraulic system Malfunction of the cooling fan Low hydraulic oil level Correct Hydraulic Oil Grade Selection

If hydraulic oil temperature rises above the recommended operating range DO NOT continue to operate the machine.

INFORMATION FUNCTIONS 1.

NOTE ALSO: Hydraulic oil temperature can also be monitored using the hydraulic oil temperature gauge shown on the main menu.

Note also that gauge symbol colour changes indicate temperature range (blue=low, white=normal, red=high)

Drive Pressure Forward - psi or bar This display indicates forward drive pressure.

2.

Drive Pressure Reverse - psi or bar This display indicates reverse drive pressure.

3.

Travel Speed - mph or km/h

The alarm must not be used to monitor the hydraulic oil. The operator must use the hydraulic oil temperature gauge on the main menu of the computer display, together with the operating range chart in SECTION 3 to prevent damage to the hydraulic system.

This display indicates machine travel speed.

Note that front tire size information is used by the machine program to accurately calculate and display machine travel speed. Refer to COMPUTER – ADJUSTMENT MENU SERVICE SETTINGS – FRONT TIRE SIZE to check or update front tire size settings.

4.

Hydraulic oil grade information is shown on the main menu below the hydraulic oil temperature gauge.

Drive Motor Speed - rpm

Operating outside the recommended operating range will shorten hydraulic component life.

This display indicates the drive motor speed in rpm.

5

Refer to COMPUTER – ADJUSTMENT MENU - SERVICE SETTINGS – HYDRAULIC OIL GRADE in THIS SECTION for hydraulic oil grade selection settings information.

Serial Number This display indicates machine serial number.

6.

Refer also to APPROVED HYDRAULIC OILS in SECTION 3 of THIS MANUAL for hydraulic oil operating range information.

Machine Hours - h This display indicates the total number of hours the machine has run.

7.

Refer also to COMPUTER – MESSAGES - CRITICAL – HYDRAULIC OIL TEMPERATURE HIGH in THIS SECTION for more information about the hydraulic oil temperature warning.

Hydraulic Oil Temperature (°F or °C) This display indicates the current hydraulic oil temperature registered in the main hydraulic tank.

If the temperature rises above the recommended operating range for the type of hydraulic oil in use, alarm will sound, check the following: 2.41

Controls and operation 8.

Tigercat 610E/615E Skidder MAIN MENU PAGE

Transmission Temperature -°F or °C This display indicates the hydrostatic circuit temperature as read by the temperature sensor located on the drive pump.

9.

From any menu page.

Total fuel information This display indicates the total fuel used during the life of the machine.

• • •

10.

Total fuel used US gal or L, Total hours h Total fuel rate US gph or L/h.

Trip fuel information

This display indicates the average fuel consumption rate for the machine since last reset.

• • •

Trip fuel used US gal or L, Trip hours h Trip fuel rate US gph or L/h.

Press the menu button to go to the main menu page.

The main menu page displays the following selections: •

Adjust - Press F1 to select

•

Measure - Press F2 to select

FUEL GAUGE

•

Preferences - Press F3 to select

The fuel level gauge is shown on the main menu.

Note that a yellow fuel symbol indicates fuel level low.

•

Info - Press F4 to select Press the back button to return to the page which was displayed when the main menu page was selected.

OR Press the menu button again to return to the page which was displayed when the main menu page was selected.

2.42

Tigercat 610E/615E Skidder ADJUST MENU

From the main menu page press the F1 button (Adjust) to access the adjust menu.

The following menu items can be selected: •

Engine Adjust Group*

•

Fan Adjust Group* (if equipped)

•

Service Adjust Group*

Controls and operation ENGINE ADJUST GROUP*

FAN ADJUST GROUP* (IF EQUIPPED)

SERVICE ADJUST GROUP*

Use the Arrow Up or Arrow Down to select the menu item. Press OK to confirm the selection. *NOTE: Marked menu items can also be accessed from the main menu. Refer to COMPUTER – ADJUSTMENT MENU in THIS SECTION for more information.

NOTE ALSO: Service technicians may have access to more options through this menu. Refer to SECTION 6 of the SERVICE MANUAL for more information.

Press the back button (or F1) to return to the main menu page.

2.43

Controls and operation MEASURE MENU

Tigercat 610E/615E Skidder

The following menu items can be selected.

From the main menu page press the F2 button (Measure) to access the measure menu.

• • • • • • • •

Inputs Outputs J1939 Parameter Inputs Drive/HP Test Function Valve Variable Pitch Fan Differential Locks Module Diagnostics

Use the Arrow Up or Arrow Down to select the menu item. Press OK to confirm the selection.

This menu is used by Tigercat service technicians.

Refer to SECTION 6 of the SERVICE MANUAL for more information.

Press the back button (or F1) to return to the main menu page.

2.44

Tigercat 610E/615E Skidder PREFERENCES MENU

Controls and operation

From the main menu page press the F3 button (Preferences) to access the preferences menu.

The following menu items can be selected for adjustment.

•

Display - Press F1 to select

•

Date/Time - Press F2 to select

•

Language - Press F3 to select Press the back button to return to the main menu page.

2.45

Controls and operation

Tigercat 610E/615E Skidder

DISPLAY ADJUSTMENT From the preferences menu press the F1 button to access display adjustment.

Screen Saver Adjustment Press F3 to access the screen saver adjustment.

•

Main Menu Page - Press F1 to select

Use the Arrow Up and Arrow Down buttons to scroll through the choices. Three choices are available:

•

Backlight - Press F2 to select Screen Saver - Press F3 to select

•

SCREEN SAVER OFF

•

•

DIMMED - Timeout - Dimmed light

•

BLACK - Timeout

The following menu items can be selected:

Press the back button to return to the preferences menu.

Backlight Adjustment Press F2 to access the backlight adjustment.

After making a selection press the OK button to confirm selection.

Use the Arrow Up or Arrow Down buttons to adjust the display backlight. The range is 10 to 100. The default setting is 100.

When the desired setting is selected press the OK button to confirm the setting. A good rule to follow is the lower the number the longer the life of the display unit.

2.46

Tigercat 610E/615E Skidder

Controls and operation

DATE/TIME ADJUSTMENT

Date Adjustment

From the preferences menu press the F2 button to access date/time adjustment.

Press F1 to access the date adjustment.

The following menu items can be selected:

Use the Arrow Up or Arrow Down to scroll through the YEAR list to select the year.

•

Date - Press F1 to select

Press the OK button to confirm year selected.

•

Time - Press F2 to select Press the back button to return to the preferences menu.

When the year has been confirmed the display will highlight the MONTH. Use the Arrow Up or Arrow Down to select the month.

Press the OK button to confirm month selected.

2.47

Controls and operation

Tigercat 610E/615E Skidder Time Adjustment Press F1 to access the time adjustment.

When the month has been confirmed the display will highlight the DAY. Use the Arrow Up or Arrow Down to select the day.

Press the OK button to confirm day selected.

Use the Arrow Up or Arrow Down to select the HOUR. Press the OK button to confirm selection.

The display will return to the Date/Time menu.

Press the back button to return to the preferences menu.

When the hour has been confirmed the display will show the MINUTES highlighted.

Use the Arrow Up or Arrow Down to select the minute.

Press OK button to confirm the selection.

The display will return to the DATE/TIME menu screen.

Press the back button to return to the preferences menu.

2.48

Tigercat 610E/615E Skidder LANGUAGE ADJUSTMENT

From the preferences menu press the F2 button to access language adjustment screen.

Controls and operation INFO MENU

From the main menu page press the F4 button (Info) and the access the info menu.

The languages available for selection will be shown.

Use the Arrow Up or Arrow Down to move to the preferred language.

Press OK to confirm the selection.

The display will return to the LANGUAGE menu screen.

Press the back button to return to the preferences menu.

The machine ID information will be displayed on the screen.

The following menu items can be selected: •

Modules - Press F1 to select

•

Logs - Press F3 to select Press the back button to return to the main menu page.

2.49

Controls and operation

Tigercat 610E/615E Skidder

MODULES

LOGS

From the Info menu press F1 to select the modules menu.

Press F3 from the info menu page to select logs.

This menu provides information on the following machine modules: • • • • •

Display (MD3 Computer Module) Cab Module (XS2 Module) Front Chassis Module 2 (XA2-A1 Module) Front Chassis Module (XA2 -A0 Module) Engine

This menu lists the logs available in the machine program and the number of records within each log.

The records are a list of all the fault occurrences in each log. Records cannot be cleared by operators.

Use the Arrow Up or Arrow Down to select the menu item. Press OK to confirm the selection.

This menu is used by Tigercat service technicians.

Refer to SECTION 6 of the SERVICE MANUAL for more information.

Press the back button (or F1) to return to the main menu page.

Shown above the MD3 module has been selected.

Specific information for the MD3 is displayed on the screen.

Use the Arrow Up or Arrow Down to select the menu item. Press OK to confirm the selection.

This menu is used by Tigercat service technicians.

Refer to SECTION 6 of the SERVICE MANUAL for more information.

Press the back button (or F1) to return to the main menu page.

2.50

Tigercat 610E/615E Skidder MESSAGES ALARM MD3 COMPUTER LIGHT

Controls and operation

MASTER ALARM

INSTRUMENT PANEL The MD3 computer displays messages, activates the master alarm and alarm light whenever a system fault occurs. Note that the computer control system will automatically perform a bulb test at engine start-up to ensure that master alarm and alarm light are functioning. Refer to STARTING ENGINE in THIS SECTION. There are different types of Messages and Alarms, they appear on the screen as a block message.

The types of messages are: • • • •

CRITICAL MESSAGE - Colour RED ERROR MESSAGE - Colour RED ALERT MESSAGE - Colour YELLOW INFORMATION MESSAGE - Colour BLUE

Messages can be hidden or acknowledged by pressing the F2 button (Hide or OK).

All messages that have been hidden or acknowledged are stored in the computer.

In some instances it will be necessary to immediately stop the machine, shut the engine OFF and repair the problem causing the message.

Active fault messages that have been hidden can be reviewed by pressing the F4 button. Recalled messages will be displayed in order starting with the highest priority first.

2.51

Controls and operation CRITICAL MESSAGES (RED)

Tigercat 610E/615E Skidder

Critical messages advise the operator that a critical machine fault is about to occur or a system fault has occurred.

Critical messages have the highest level of priority and are used to alert operator that immediate action must be taken to prevent damage to machine or to ensure operator safety.

When a critical message is displayed, the master alarm and alarm light will sound and flash continuously. The message remains on the screen until the operator hides it.

A list of CRITICAL MESSAGES is as follows:

The message will give brief details of the fault and advise what action is necessary.

In some instances the machine requires immediate action to correct the problem which requires the operator to STOP machine operation, SHUT THE ENGINE OFF and service the machine to correct the problem.

Hydraulic Oil Level Low Drive Motor Clutch Pressure Low Drive Motor Overspeed Transmission Oil Temperature High Interlock System Hydraulic Oil Temperature High LH Drive Motor Speed Sensor Fault

Critical messages flash the critical symbol above the F4 button when active messages are hidden. The symbol will continue to flash until the problem is resolved and the fault becomes inactive.

RH Drive Motor Speed Sensor Fault or Clutch Slip Drive Motor Clutch Slow Response Hardware Fault - MD3 Hardware Fault - Engine Hardware Fault - XS2 Hardware Fault - XA2 Engine Coolant Temperature High Engine Coolant Level low Aftertreatment System Technical Failure Aftertreatment System Engine Idle Too Long Engine Torque Derate Active Engine Locked Out Engine Restarts Remaining Until Engine Lockout Engine Oil Pressure Low

Active messages that have been hidden can be reviewed by pressing the F4 button.

Engine Oil Temperature High Engine Fault Code Messages - Critical

However, if the machine cannot be stopped immediately for safety reasons, the operator can hide the message. In this instance the machine should only be operated long enough to move the machine to a safe location then STOP machine operation and SHUT THE ENGINE OFF before serious machine damage can occur!

Messages can be hidden by pressing the F2 button (Hide).

2.52

Tigercat 610E/615E Skidder CRITICAL MESSAGES

Controls and operation

Drive Motor Hydraulic Oil

Overspeed. Reduce travel speed.

Level Low.

HYDRAULIC OIL LEVEL LOW

LH Drive Motor

This message will be displayed, alarm warning light will flash and alarm will sound when the main hydraulic tank oil level is low.

Overspeed. Reduce travel speed.

Stop the engine immediately when this alarm is activated. Operating machine with a low hydraulic oil level can cause hydraulic pumps to fail.

When this alarm is activated stop the engine and look for signs of broken hoses or other leaks.

Repair leaks and refill the main hydraulic tank to FULL mark on the sight gauge with grapple head fully open, grapple head and dozer blade on the ground. Restart engine and inspect for leaks.

Drive Motor Clutch Pressure Low.

DRIVE MOTOR CLUTCH PRESSURE LOW (IF EQUIPPED WITH EHS TRANSMISSION) This message will be displayed, alarm warning light will flash and alarm will sound when the drive motor clutch pressure is low.

RH Drive Motor Overspeed. Reduce travel speed.

DRIVE MOTOR OVERSPEED This message will be displayed, alarm warning light will flash and alarm will sound when the drive motor is overspeeding.

Reduce speed immediately when this alarm is activated to prevent damage to the machine.

Operating drive motors at high speeds will damage the drive motors.

Note that machines equipped with an EHS transmission have separate messages for left hand and right hand drive motors.

Stop the machine immediately when this alarm is activated and check the EHS transmission for proper operation.

2.53

Controls and operation

Tigercat 610E/615E Skidder

Transmission Oil

Hydraulic Oil

Temperature High

TRANSMISSION OIL TEMPERATURE HIGH (IF EQUIPPED WITH EHS TRANSMISSION)

Temperature High.

HYDRAULIC OIL TEMPERATURE HIGH

This message will be displayed, alarm warning light will flash and alarm will sound when the transmission oil temperature is high.

This message will be displayed, alarm warning light will flash and alarm will sound when the oil temperature exceeds the recommended operating range for the type of hydraulic oil in use.

Stop the machine immediately when this alarm is activated and check the EHS transmission for proper operation.

If the temperature rises above the recommended operating range for the type of hydraulic oil in use check the following: • • • • • •

Plugged oil cooler Malfunction in a hydraulic system High loads on the hydraulic system Malfunction of the cooling fan Low hydraulic oil level Correct Hydraulic Oil Grade Selection

If hydraulic oil temperature rises above the recommended operating range DO NOT continue to operate the machine.

Interlock System Door open or park brake on! Machine drive disabled.

INTERLOCK SYSTEM This message will be displayed, alarm warning light will flash and alarm will sound to a alert the operator that the Interlock System has disabled the machine drive.

The interlock system prevents the machine from being driven and function controls from being operated while the parking brake is ENGAGED. The parking brake is operated using the parking brake switch or lever. This message indicates that the parking brake was engaged by the parking brake control or opening a cab door while the machine was in motion.

This alarm must not be used to monitor the hydraulic oil. The operator must use the hydraulic oil temperature gauge on the main menu, together with the operating range chart in SECTION 3 to prevent damage to the hydraulic system.

Hydraulic oil grade information is shown on the main menu below the hydraulic oil temperature gauge.

Operating outside the recommended operating range will shorten hydraulic component life.

Refer to COMPUTER – ADJUSTMENT MENU SERVICE SETTINGS – HYDRAULIC OIL GRADE in THIS SECTION for hydraulic oil grade selection settings information.

Refer also to APPROVED HYDRAULIC OILS in SECTION 3 of THIS MANUAL for hydraulic oil operating range information.

Refer to COMPUTER – INFORMATION MODE MENU – HYDRAULIC OIL TEMPERATURE in THIS SECTION for hydraulic oil temperature information display.

2.54

Tigercat 610E/615E Skidder

Controls and operation

LH Drive Motor

Drive Motor Clutch

Speed sensor fault

Slow response.

LH DRIVE MOTOR SPEED SENSOR FAULT (IF EQUIPPED WITH EHS TRANSMISSION)

DRIVE MOTOR CLUTCH SLOW RESPONSE (IF EQUIPPED WITH EHS TRANSMISSION)

This message will be displayed, alarm warning light will flash and alarm will sound when a speed sensor fault is detected in the left hand drive motor.

This message will be displayed, alarm warning light will flash and alarm will sound when there is a delay in clutch response.

Stop the machine immediately when this alarm is activated and check the EHS transmission for proper operation. Air may be present in the circuit causing slow clutch response, check to ensure suction line is tight.

Stop the machine immediately when this alarm is activated and check the speed sensor for proper operation.

Check for proper sensor functionality, wiring, connectors and calibration. Refer to DRIVE MOTOR SPEED SENSOR INSTALLATION in SECTION 8 of the SERVICE MANUAL.

RH Drive Motor Speed sensor fault or clutch slip.

RH DRIVE MOTOR SPEED SENSOR FAULT OR CLUTCH SLIP (IF EQUIPPED WITH EHS TRANSMISSION) This message will be displayed, alarm warning light will flash and alarm will sound when a speed sensor fault is detected in the right hand drive motor or the clutch is slipping.

Stop the machine immediately when this alarm is activated. Check for proper sensor functionality, wiring, connectors and calibration first. Refer to DRIVE MOTOR SPEED SENSOR INSTALLATION in SECTION 8 of the SERVICE MANUAL. Check EHS transmission for clutch slip and proper operation only if speed sensor is found to be ok.

2.55

Controls and operation

Tigercat 610E/615E Skidder

Hardware Fault - MD3

Hardware Fault - XS2

Active fault has been hidden. Turn key off and on to recall active hidden hardware faults.

Active fault has been hidden. Turn key off and on to recall active hidden hardware faults.

HARDWARE FAULT - MD3

HARDWARE FAULT - XS2

This message will be displayed, alarm warning light will flash and alarm will sound when a critical active hardware fault related to the MD3 Display Module has been hidden.

This message will be displayed, alarm warning light will flash and alarm will sound when a critical active hardware fault related to the XS2 Cab Module has been hidden.

To recall the original active fault(s) the operator must turn the key off and on.

To recall the original active fault(s) the operator must turn the key off and on.

A VREF error is an example of the type of hardware fault which will be the original active fault which triggers this message.

A VREF and no contact errors are examples of the type of hardware fault which may be the original active fault which triggers this message.

Hardware Fault - Engine

Hardware Fault - XA2

Active fault has been hidden. Turn key off and on to recall active hidden hardware faults.

Active fault has been hidden. Turn key off and on to recall active hidden hardware faults.

HARDWARE FAULT - ENGINE

HARDWARE FAULT - XA2

This message will be displayed, alarm warning light will flash and alarm will sound when a critical active hardware fault related to the Engine has been hidden.

This message will be displayed, alarm warning light will flash and alarm will sound when a critical active hardware fault related to the XA2 Front Chassis Module has been hidden.

To recall the original active fault(s) the operator must turn the key off and on.

To recall the original active fault(s) the operator must turn the key off and on.

No contact error is an example of the type of hardware fault which may be the original active fault which triggers this message.

A VREF and no contact errors are examples of the type of hardware fault which may be the original active fault which triggers this message.

2.56

Tigercat 610E/615E Skidder

Controls and operation

SPN: 63011 1 of 1

Engine Coolant

Engine coolant temperature high.

Level Low.

ENGINE COOLANT TEMPERATURE HIGH

ENGINE COOLANT LEVEL LOW

This message will be displayed, alarm warning light will flash and alarm will sound when engine temperature exceeds recommended engine temperature.

This message will be displayed, alarm warning light will flash and alarm will sound when the coolant level drops below a safe operating level.

The sensor is located in the surge tank.

When this alarm is activated check for:

If this light comes on when the engine is running, stop the engine immediately and correct the fault.

With engine running, top up radiator using correct solution of coolant antifreeze.

• •

Plugged air intake access panel screens Plugged radiator.

DO NOT continue to operate machine.

Refer to CLEANING A/C CONDENSER AND COOLING ASSEMBLY in THIS SECTION.

Refer to SERVICE AND LUBRICATION POINTS CHART in SECTION 3 of THIS MANUAL.

WARNING

DO NOT remove the radiator fill cap when the engine is hot, release of pressurized coolant can cause serious burns.

Turn the engine OFF. Only remove engine radiator fill cap when cool enough to touch with bare hands.

Slowly loosen cap to first stop to relieve pressure before removing completely.

2.57

Controls and operation

Tigercat 610E/615E Skidder

Aftertreatment System

Aftertreatment System

Technical failure severe. Engine lockout may occur after full torque derate and 3 engine restarts.

Engine idle too long. Shutdown engine to prevent damage to emission control system.

AFTERTREATMENT SYSTEM TECHNICAL FAILURE

AFTERTREATMENT SYSTEM ENGINE IDLE TOO LONG

This message will be displayed, alarm warning light will flash and alarm will sound when an aftertreatment techical fault is detected. Action to correct the problem should be taken immediately to avoid affecting engine performance and damage to the diesel oxidation catalyst /selective catalytic reduction (DOC/SCR) aftertreatment system components.

This message will be displayed, alarm warning light will flash and alarm will sound when this engine has idled for more than 9 consecutive hours. Shutdown engine to prevent damage to the emission control system.

This warning results in the following derate sequence if no action is taken to correct the problem: •

• • • •

Beginning immediately after an aftertreatment system technical warning there will be a ramp down of Torque by 25% over 25 minutes.

After 1 hour at reduced torque there will be a ramp down of Engine Speed by 60% and Torque by 65% over 40 minutes.

After 50 minutes at derated engine speed and torque the engine is derated to idle within 30 minutes.

Some less severe technical faults can be fixed at any time, even after the engine has been fully derated to idle speed.

More severe technical faults will result in an engine lockout when the engine has derated to idle and there have been 3 restarts (redetects). Once locked out the engine will only operate at idle. Action to correct the original cause(s) of the lockout must be taken before the engine can be reset. Contact dealer to reset engine lockout for normal operation.

Refer to COMPUTER – MESSAGES CRITICAL – ENGINE LOCKED OUT and ENGINE RESTARTS REMAINING UNTIL ENGINE LOCKOUT in THIS SECTION.

Identify the cause of the technical failure and take action to correct the problem.

Refer also to AFTERTREATMENT SYSTEM in SECTION 3 of THIS MANUAL for more information.

IMPORTANT !

Engine should not idle longer than 9 consecutive hours. Damage to the emission control system will result. When this machine idles for an extended period excess hydrocarbon buildup is created in the DOC/SCR aftertreatment system. Burn off of excess hydrocarbon at full load immediately after a long idle period will generate excess heat which will cause damage to emission control system components.

SPN: 62191 1 of 1 Engine torque derate active.

ENGINE TORQUE DERATE ACTIVE This message will be displayed, alarm warning light will flash and alarm will sound when the Engine ECU has derated the engine. The code for a Torque Derate / Diesel Exhaust Fluid Empty is shown above as an example.

Refer to Engine Manuals for code information to identify the cause(s) of engine derating and more information regarding failure cause and repair.

2.58

Tigercat 610E/615E Skidder

Controls and operation

Engine

Engine

Engine locked out. Engine derate to 0% Torque and 850 rpm. Contact Dealer

3 restarts remaining until engine lockout.

ENGINE LOCKED OUT This message will be displayed, alarm warning light will flash and alarm will sound when an engine is locked out by the computer system to prevent further damage to the engine and aftertreatment system.

ENGINE RESTARTS REMAINING UNTIL ENGINE LOCKOUT This message will be displayed, alarm warning light will flash and alarm will sound to inform the operator of the number of restarts available before the engine is locked out.

Note that an engine is locked out after several other critical aftertreatment system warnings regarding the cause of the problem and additional warnings regarding the number of restarts until engine lockout.

Note that an engine is locked out after several other critical aftertreatment system warnings regarding the cause of the problem and this warning regarding the number of restarts until engine lockout.

Once locked out the engine will only operate at idle. Action to correct the original cause(s) of the lockout must be taken before the engine can be reset. Contact dealer to reset engine lockout for normal operation.

Refer also to COMPUTER – MESSAGES CRITICAL – ENGINE LOCKED OUT in THIS SECTION.

Refer to Engine Manuals for code information.

Refer also to COMPUTER – MESSAGES - CRITICAL – ENGINE RESTARTS REMAINING UNTIL ENGINE LOCKOUT in THIS SECTION.

2.59

Controls and operation

Tigercat 610E/615E Skidder

SPN: 9939 1 of 1

SPN: 4645 1 of 1

Engine Oil Pressure Low.

Contact dealer.

ENGINE OIL PRESSURE LOW

ENGINE FAULT CODE MESSAGES - CRITICAL

This message will be displayed, alarm warning light will flash and alarm will sound when engine oil pressure falls below 10psi (0.7 bar).

Critical engine fault message(s) will be displayed, alarm warning light will flash and alarm will sound when a critical engine fault message is received from the engine electronic control module.

Stop the engine when this alarm is activated.

Check engine oil levels.

Refer to STARTING ENGINE in THIS SECTION for more information.

They provide the SPN code (suspect parameter number) as well as a message describing the fault (when available).

Critical engine fault codes are higher priority messages than alert level engine fault code messages. Critical messages can be hidden but immediate action must be taken, STOP machine operation and service engine immediately to resolve the cause of the fault.

An example of a critical engine fault message is shown above.

SPN: 7123 1 of 1 Engine oil temperature high.

ENGINE OIL TEMPERATURE HIGH This message will be displayed, alarm warning light will flash and alarm will sound when engine oil temperature exceeds recommended engine temperature.

Note that some less common engine fault codes will appear without a message describing the fault.

Make a note of the SPN code and contact service for more information.

Refer to engine manual for specific information regarding the engine and aftertreatment system.

NOTE: Contact your Tigercat dealer to obtain an Engine Fault Codes chart. An up to date copy should be kept in the Manual’s Box (in the cab). The chart is updated regularly by the engine manufacturer, so it is important to check periodically with the Tigercat dealer to ensure that you have a current copy of the Engine Fault Codes chart.

Check the cooling assembly and fan for proper operation and run a clean cycle if the machine is equipped with a variable pitch fan. It is also important to manually clean debris from the machine on a regular basis to maintain low machine operating temperatures. Refer to CLEANING A/C CONDENSER AND COOLING ASSEMBLY in THIS SECTION. Refer to Engine manuals for more information.

2.60

Tigercat 610E/615E Skidder ERROR MESSAGES (RED)

Controls and operation

Error messages advise the operator that a critical machine fault is about to occur or a system fault has occurred.

Error messages are computer system generated and are generally triggered by computer system error and fault related conditions.

Error messages have the second highest level of priority and are used to alert operator that immediate action must be taken to prevent damage to machine or to ensure operator safety.

A list of some types of ERROR MESSAGES is as follows:

Error messages are activated whenever a fault such as an electrical connection is broken/ disconnected. Most error messages are due to computer system hardware or connection faults.

Module No Contact Error Module VREF Error Voltage Input Error (VIN)

When an error message is displayed, the master alarm and alarm light will sound and flash continuously. The message remains on the screen until the operator hides it.

Digital Input Error (DIN) Digital Output Error (DOUT) Current Output Error (COUT)

The message will give brief details of the fault and advise what action is necessary.

* Note that not all error messages are shown.

In some instances the machine requires immediate action to correct the problem which requires the operator to STOP machine operation, SHUT THE ENGINE OFF and service the machine to correct the problem.

However, if the machine cannot be stopped immediately for safety reasons, the operator can hide the message. In this instance the machine should only be operated long enough to move the machine to a safe location then STOP machine operation and SHUT THE ENGINE OFF before serious machine damage can occur!

Messages are acknowledged by pressing the F2 button (OK). To recall active messages turn key off and on. On screen messages will indicate to the operator that an active hardware fault has been hidden.

Error messages flash the critical symbol

or the

above the F4 button when active messages are hidden depending on the type of error message. The symbol will continue to flash until the problem is resolved and the fault becomes inactive.

Active messages that have been hidden can be reviewed by pressing the F4 button.

2.61

Controls and operation ERROR MESSAGES

Tigercat 610E/615E Skidder XS2-A0

MODULE NO CONTACT ERROR The module no contact error message will be displayed to indicate a loss of communication with or power to a module. The module is identified on the display screen.

Cab Module No contact

When a module loses contact all machine functions controlled by that module cease and all messages associated with that module are triggered. If the problem is with the CAN wires all modules beyond the problem module will also be affected.

XA2-A0

Front Chassis Module

Note that if the MD3 display module has a loss of power or other malfunction the screen may go blank and all machine functions controlled by the computer system will be affected..

No contact

Once acknowledged this message will be replaced with a hardware fault message for the corresponding module when active faults are recalled to the screen. Refer to COMPUTER – MESSAGES - CRITICAL – HARDWARE FAULT in THIS SECTION.

XA2-A1

Front Chassis Module 2 No contact

J1939-B0

Tigercat/ FPT NEF 6.7L No contact

2.62

Tigercat 610E/615E Skidder

Controls and operation

MODULE VREF ERROR

MD3

The module VREF message will be displayed to indicate a problem related to the 5V reference signal coming from the module.

Display VREF error

The module is identified on the display screen.

This message indicates a problem with a sensor, connecting wires or the 5V reference signal itself.

Once acknowledged this message will be replaced with a hardware fault message for the corresponding module when active faults are recalled to the screen. Refer to COMPUTER – MESSAGES - CRITICAL – HARDWARE FAULT in THIS SECTION.

XS2-A0

Cab Module VREF error

XA2-A0

Front Chassis Module VREF error

XA2-A1

Front Chassis Module 2 VREF error

2.63

Controls and operation

Tigercat 610E/615E Skidder Cab Module Pin C1:25

Travel Direction Select VIN High error

CURRENT OUTPUT ERROR (COUT) Current output error messages will be displayed to indicate a problem with a current output signal from a computer system module.

The module and pin number are identified on the display screen.

The heading identifies the signal destination and the text indicates the type of error.

VOLTAGE INPUT ERROR (VIN) Voltage input error messages will be displayed to indicate a problem with a voltage input signal to a computer system module.

The module and pin number are identified on the display screen.

The display is similar to the voltage input error message shown above.

Once acknowledged these message will be replaced with a hardware failure message for the corresponding module when active faults recalled to the screen. Refer to COMPUTER – MESSAGES - ALERT – HARDWARE FAILURE in THIS SECTION.

The heading identifies the signal source and the text indicates the type of error.

An example of a voltage input error message is shown above.

DIGITAL INPUT ERROR (DIN) Digital input error messages will be displayed to indicate a problem with a digital input signal to a computer system module.

The module and pin number are identified on the display screen.

The heading identifies the signal source and the text indicates the type of error.

The display is similar to the voltage input error message shown above.

DIGITAL OUTPUT ERROR (DOUT) Digital output error messages will be displayed to indicate a problem with a digital output signal from a computer system module.

The module and pin number are identified on the display screen.

The heading identifies the signal destination and the text indicates the type of error.

The display is similar to the voltage input error message shown above.

2.64

Tigercat 610E/615E Skidder ALERT MESSAGES (YELLOW)

Controls and operation

Alert messages advise the operator that machine operation will be compromised.

Alert messages have the third level of priority and are used to indicate to the operator that action is required to prevent future damage to the machine.

All alert message will give brief details of the fault and advise what action is necessary.

Action should be taken to service the machine to correct the problem at the earliest opportunity to prevent future damage to the machine.

Alert messages flash the alert symbol above the F4 button when active messages are hidden.

There are two types of alert messages: Alert programmed messages generally triggered by machine function related conditions.

When an alert message is displayed, the master alarm and light will sound and flash three times to alert the operator of the message. The message remains on the screen until the operator hides it.

Messages can be hidden by pressing the F2 button (Hide).

Active messages that have been hidden can be reviewed by pressing the F4 button. The symbol will continue to flash until the problem is resolved and the fault becomes inactive.

Note that if both a critical level fault and an alert level fault are present the critical symbol will take priority until the critical fault becomes inactive.

Alert computer system generated messages are generally triggered by computer system error and fault related conditions.

When a system generated alert message is displayed he master alarm and light will sound and flash three times to alert the operator of the message.

The message remains on the screen until the operator hides it.

Note that active hardware fault alert messages are acknowledged by pressing the F2 button (OK).

To recall these messages turn key off and on. On screen messages will indicate to the operator that an active hardware fault has been hidden.

2.65

Controls and operation

Tigercat 610E/615E Skidder

A list of ALERT MESSAGES is as follows: Fuel Level low.

Engine Air Intake Filter Restricted Drive Charge Filter Bypassed Machine Voltage Low. Machine Voltage High Service Brake Pressure Low Drive Charge System Pressure Low. Hardware Fault - MD3 Hardware Fault - XS2 Hardware Fault - XA2 Hardware Failure - VIN Hardware Failure - DIN Hardware Failure -DOUT Hardware Failure -COUT Engine Voltage Low Engine Voltage High Fuel Water In Fuel Engine Coolant Temperature High Diesel Exhaust Fluid Level <10% Diesel Exhaust Fluid Level <5% Diesel Exhaust Fluid Level Empty Diesel Exhaust Fluid Quality Engine Fault Code Messages - Alert Some types of computer system generated alert messages are listed below: Module High Temperature - Alert Module High Supply Voltage - Alert Module Low Supply Voltage - Alert * Note that not all system generated alert messages are shown.

2.66

Tigercat 610E/615E Skidder ALERT MESSAGES

Controls and operation

Drive Charge Filter Bypassed. Service machine to correct.

Fuel Level low.

DRIVE CHARGE FILTER BYPASSED This message will be displayed when an oil flow restriction in excess of 50 psi (3.5 bar) is encountered at the hydrostatic oil charge filter.

This pressure build up also opens the filter bypass valve in the filter head allowing oil to bypass the filter element.

FUEL LEVEL LOW This message will be displayed when the fuel level falls below 5% of full.

Note that the fuel gauge symbol changes from its normal white to yellow when fuel level is low.

When this happens the filter requires immediate service.

Refer to FUEL TANK in THIS SECTION for tank capacities.

If alarm sounds during cold start-ups, the engine speed should be reduced and the warm up procedure continued. Note that the bypass warning will only be displayed when hydraulic oil temperature is above 85°F (29°C) and the filter is in bypass mode.

Engine Air Intake Filter

Machine Voltage

Restricted. Service Machine to correct.

Low. Service machine to correct.

ENGINE AIR INTAKE FILTER RESTRICTED

MACHINE VOLTAGE LOW

This message will be displayed when a signal is received from the restriction indicator switch on the engine air cleaner.

This message will be displayed when machine voltage readings of less than 20 volts are detected.

When this happens the engine air cleaner requires immediate service.

Machine voltage readings indicate voltage levels in the electrical system.

Refer to AIR CLEANER MAINTENANCE in SECTION 3 of THIS MANUAL.

When this alarm is activated investigate the cause immediately.

2.67

Controls and operation

Tigercat 610E/615E Skidder

Machine Voltage

Drive Charge System

High. Service machine to correct.

Pressure Low. Service machine to correct.

MACHINE VOLTAGE HIGH

DRIVE CHARGE SYSTEM PRESSURE LOW

This message will be displayed when machine voltage readings of greater than 30 volts are detected.

This message will be displayed when drive charge pressure falls below 250 psi (17 bar). The charge pressure is monitored at the forward and reverse pressure sensors on the drive pump.

Machine voltage readings indicate voltage levels in the electrical system.

When this alarm is activated investigate the cause immediately.

When this warning is activated check the charge filter for proper operation then, if necessary, check the charge pressure using a gauge.

Refer to DRIVE PUMP PRESSURE CHECKS in SECTION 8 of THE SERVICE MANUAL. Refer also to COMPUTER – MESSAGES ALERT – DRIVE CHARGE FILTER BYPASSED warning in THIS SECTION.

Service Brake Pressure Low. Service machine to correct.

SERVICE BRAKE PRESSURE LOW This message will be displayed when service brake pressure falls below 800 psi (55 bar).

When this warning is activated check first for leaks in the brake circuit. If no leaks are found check for proper operation of the brake pedal valve, accumulator, check valve and brake pressure sensor.

For more information about the service brake circuit refer to SECTION 9 of THE SERVICE MANUAL.

2.68

Tigercat 610E/615E Skidder

Controls and operation

Hardware Fault - MD3

Hardware Fault - XA2

Active fault has been hidden. Turn key off and on to recall active hidden hardware faults.

Active fault has been hidden. Turn key off and on to recall active hidden hardware faults.

HARDWARE FAULT - MD3

HARDWARE FAULT - XA2

This message will be displayed when an alert level active hardware fault related to the MD3 Display Module has been hidden.

This message will be displayed when an alert level active hardware fault related to the XA2 Front Chassis Module has been hidden.

To recall the original active fault(s) the operator must turn the key off and on.

To recall the original active fault(s) the operator must turn the key off and on.

High temperature, low supply voltage and high supply voltage module alert messages are examples of the type of hardware fault which will be the original active faults which trigger this message.

High temperature, low supply voltage and high supply voltage module alert messages are examples of the type of hardware fault which will be the original active faults which trigger this message.

Hardware Fault - XS2 Active fault has been hidden. Turn key off and on to recall active hidden hardware faults.

HARDWARE FAULT - XS2 This message will be displayed when an alert level active hardware fault related to the XS2 Cab Module has been hidden.

To recall the original active fault(s) the operator must turn the key off and on.

High temperature, low supply voltage and high supply voltage module alert messages are examples of the type of hardware fault which will be the original active faults which trigger this message.

2.69

Controls and operation

Tigercat 610E/615E Skidder

Hardware Failure - VIN

Hardware Failure - DOUT

Active fault has been hidden. Turn key off and on to recall active hidden hardware faults.

Active fault has been hidden. Turn key off and on to recall active hidden hardware faults.

HARDWARE FAILURE - VIN

HARDWARE FAILURE - DOUT

This message will be displayed when a voltage input error message has been hidden.

This message will be displayed when a digital output error message has been hidden.

To recall the original active fault(s) the operator must turn the key off and on.

To recall the original active fault(s) the operator must turn the key off and on.

Hardware Failure - DIN

Hardware Failure - COUT

Active fault has been hidden. Turn key off and on to recall active hidden hardware faults.

Active fault has been hidden. Turn key off and on to recall active hidden hardware faults.

HARDWARE FAILURE - DIN

HARDWARE FAILURE - COUT

This message will be displayed when a digital input error message has been hidden.

This message will be displayed when a current output error message has been hidden.

To recall the original active fault(s) the operator must turn the key off and on.

To recall the original active fault(s) the operator must turn the key off and on.

2.70

Tigercat 610E/615E Skidder

Controls and operation

SPN: 62755 1 of 1

SPN: 8801 1 of 1

Engine coolant temperature high.

Engine voltage low.

ENGINE VOLTAGE LOW

ENGINE COOLANT TEMPERATURE HIGH

This message will be displayed when engine voltage readings of less than 20 volts are detected.

This message will be displayed, alarm warning light will flash and alarm will sound when engine temperature exceeds recommended engine temperature.

When this alarm is activated investigate the cause immediately.

Investigate cause as soon as possible.

When this alarm is activated check for:

• •

Plugged air intake access panel screens Plugged radiator.

Refer to CLEANING A/C CONDENSER AND COOLING ASSEMBLY in THIS SECTION. Refer to COMPUTER – MESSAGES - CRITICAL – ENGINE COOLANT TEMPERATURE HIGH.

SPN: 4449 1 of 1 Engine voltage high.

SPN: 17429 1 of 1 Water in Fuel.

ENGINE VOLTAGE HIGH This message will be displayed when engine voltage readings of greater than 30 volts are detected.

When this alarm is activated investigate the cause immediately.

FUEL - WATER IN FUEL This message will be displayed when water is detected in the fuel by the engine computer system.

Refer to engine manufacturer's manual for specific information regarding the engine.

2.71

Controls and operation

Tigercat 610E/615E Skidder

DIESEL EXHAUST FLUID LEVEL WARNINGS There are three levels of diesel exhaust fluid level warnings generated by the Engine ECU.

SPN: 64191 1 of 1 DEF tank empty.

SPN: 61839 1 of 1 DEF Level below 10%.

DIESEL EXHAUST FLUID LEVEL <10% This message will be displayed, alarm warning light will flash and alarm will sound when a diesel exhaust fluid level below 10% is detected. Action to correct DEF levels should be taken immediately to avoid affecting engine performance and damage to the diesel oxidation catalyst /selective catalytic reduction (DOC/SCR) aftertreatment system components.

Fill DEF tank and restart engine to clear the warning.

Refer to DIESEL EXHAUST FLUID TANK in SECTION 2 of THIS MANUAL.

DIESEL EXHAUST FLUID LEVEL EMPTY This message will be displayed, alarm warning light will flash and alarm will sound when diesel exhaust fluid level empty is detected. Action to correct DEF levels should be taken immediately to avoid affecting engine performance and damage to the diesel oxidation catalyst /selective catalytic reduction (DOC/SCR) aftertreatment system components.

•

Beginning immediately after a DEF level empty warning, the engine is derated to idle within 30 minutes.

Fill DEF tank and restart engine to clear the warning.

Note that an Engine Torque Derate Active warning will also be triggered as the engine begins to derate. Refer to COMPUTER – MESSAGES CRITICAL – ENGINE TORQUE DERATE ACTIVE.

SPN: 62095 1 of 1 DEF Level below 5%.

DIESEL EXHAUST FLUID LEVEL <5% This message will be displayed, alarm warning light will flash and alarm will sound when a diesel exhaust fluid level below 5% is detected. Action to correct DEF levels should be taken immediately to avoid affecting engine performance and damage to the diesel oxidation catalyst /selective catalytic reduction (DOC/SCR) aftertreatment system components.

• Beginning immediately after a DEF level <5% warning, there will be a ramp down of Engine Speed by 60% and Torque by 65% over 40 minutes.

Fill DEF tank and restart engine to clear the warning.

2.72

Tigercat 610E/615E Skidder

Controls and operation WARNING Use only diesel exhaust fluid (DEF) which meets ISO 22241 specifications. NEVER fill the DEF tank with any other fluid.

DEF fluid is injected into the exhaust gas stream during normal operation of the Selective Catalytic Reduction (SCR) aftertreatment system.

Use of other fluids may cause component damage, or a fire risk which could result in death or serious injury.

SPN: 19402 1 of 2 DEF quality low.

SPN: 19658 2 of 2 DEF quality low.

DIESEL EXHAUST FLUID QUALITY This message will be displayed, alarm warning light will flash and alarm will sound when a diesel fluid quality problem is detected. Action to correct the problem should be taken immediately to avoid affecting engine performance and damage to aftertreatment system components.

This warning results in the following derate and engine lockout sequence if no action is taken to correct the problem: • Beginning 1 hour after a DEF quality warning there will be a ramp down of Engine Speed by 60% and Torque by 65% over 40 minutes.

• After 2 hours at derated engine speed and torque the engine is derated to idle within 30 minutes.

To correct the DEF quality problem clean the area around the DEF tank then drain and refill the tank with clean DEF which meets ISO 22241 specifications.

Note that an Engine Torque Derate Active warning will also be triggered as the engine begins to derate. Refer to COMPUTER – MESSAGES CRITICAL – ENGINE TORQUE DERATE ACTIVE. Refer to DIESEL EXHAUST FLUID TANK in SECTION 2 of THIS MANUAL and DRAINING DEISEL EXHAUST FLUID TANK in SECTION 3 of THIS MANUAL. Refer also to AFTERTREATMENT SYSTEM in SECTION 3 of THIS MANUAL for more information regarding the use of DEF and its function in the DOC/SCR aftertreatment system.

2.73

Controls and operation

Tigercat 610E/615E Skidder

SPN: ###### 1 of 1 Contact dealer.

ENGINE FAULT CODE MESSAGES - ALERT Alert engine fault message(s) will be displayed, alarm warning light will flash and alarm will sound when an alert engine fault message is received from the engine electronic control module.

They provide the SPN code (suspect parameter number) as well as a message describing the fault (when available).

Alert engine fault codes are lower priority messages than critical level engine fault code messages. Alert messages can be hidden but action (service engine) is required to resolve the cause of the fault.

An example of an alert engine fault message is shown above.

Note that some less common engine fault codes will appear without a message describing the fault.

Make a note of the SPN code and contact service for more information.

Refer to engine manual for specific information regarding the engine and aftertreatment system.

NOTE: Contact your Tigercat dealer to obtain an Engine Fault Codes chart. An up to date copy should be kept in the Manual’s Box (in the cab). The chart is updated regularly by the engine manufacturer, so it is important to check periodically with the Tigercat dealer to ensure that you have a current copy of the Engine Fault Codes chart.

2.74

Tigercat 610E/615E Skidder

Controls and operation

MODULE HIGH TEMPERATURE - ALERT

MD3

Module high temperature alert message will be displayed to indicate that the computer control system has detected high temperature readings in a system module.

Display High temperature

The module is identified on the display screen.

The temperature reading value is also displayed.

Value: 75° C

Once acknowledged this message will be replaced with a hardware fault message for the corresponding module when active faults are recalled to the screen. Refer to COMPUTER – MESSAGES - ALERT – HARDWARE FAULT in THIS SECTION.

XS2-A0

Cab Module High temperature

Value: 75° C

XA2-A0

Front Chassis Module High temperature

Value: 75° C

XA2-A1

Front Chassis Module 2 High temperature

Value: 75° C

2.75

Controls and operation

Tigercat 610E/615E Skidder

MODULE HIGH SUPPLY VOLTAGE - ALERT

MD3

Module high supply voltage alert message will be displayed to indicate that the computer control system has detected high supply voltage readings in a system module.

Display High supply voltage

The module is identified on the display screen.

The voltage reading value is also displayed.

Value: 34 V

Once acknowledged this message will be replaced with a hardware fault message for the corresponding module when active faults are recalled to the screen. Refer to COMPUTER – MESSAGES - ALERT – HARDWARE FAULT in THIS SECTION.

XS2-A0

Cab Module High supply voltage

Value: 34 V

XA2-A0

Front Chassis Module High supply voltage

Value: 75° C

XA2-A1

Front Chassis Module 2 High supply voltage

Value: 34 V

2.76

Tigercat 610E/615E Skidder

Controls and operation

MODULE LOW SUPPLY VOLTAGE - ALERT

MD3

Module low supply voltage alert message will be displayed to indicate that the computer control system has detected low supply voltage readings in a system module.

Display Low supply voltage

The module is identified on the display screen.

Once acknowledged this message will be replaced with a hardware fault message for the corresponding module when active faults are recalled to the screen. Refer to COMPUTER – MESSAGES - ALERT – HARDWARE FAULT in THIS SECTION.

XS2-A0

Cab Module Low supply voltage

XA2-A0

Front Chassis Module Low supply voltage

XA2-A1

Front Chassis Module 2 Low supply voltage

2.77

Controls and operation INFORMATION MESSAGES (BLUE)

Tigercat 610E/615E Skidder

Information messages give the operator information regarding an event or problem condition while the event or problem exists.

Information messages have lowest priority and are used to give the operator information that is useful to the operator, but requires no action to prevent immediate or future damage to the machine When an information message is displayed on the screen the message will either automatically disappear when the condition no longer exists or stay on the screen until the operator acknowledges the message.

Information messages can be acknowledged by pressing the F2 button (OK). Acknowledged information messages are removed from the screen.

A list of the INFORMATION MESSAGES is as follows: Setup Mode - Engine HP Test Setup Mode - Drive Motor Setup Setup Mode - Drive Pump POR Setup Setup Mode - Drive Pump Regulation Setup Setup Mode - Function Setup Setup Mode - Max Current Setup (if equipped*) Machine Steering Invert Disabled * NOTE: Used for machines equipped with EHS transmission only.

Information messages do not have an indicator after they have been acknowledged.

Most information messages that have been acknowledged cannot be reviewed.

Recurrence of an event or problem condition related to an information message may cause the message to be shown again.

Restarting the machine may also cause the message to be shown again.

2.78

Tigercat 610E/615E Skidder INFORMATION MESSAGES SETUP MODE One of these messages will be displayed until the message is acknowledged when the machine is placed in a service program mode: • Engine HP Test Mode • Drive Motor Setup Mode • Drive Pump POR Setup Mode • Drive Pump Regulation Setup • Function Setup Mode • Max Current Setup Mode (if equipped) Setup Program Modes are intended for setup and testing and should only be used by qualified Tigercat service technicians or on specific instructions from a service technician.

Controls and operation IMPORTANT !

Machine must be in the Normal Program Mode to operate normally.

Other program modes are used for service/setup procedures only.

When setup program modes are chosen an information message is shown on the electronic display until the message is acknowledged.

In each program mode some controls are deactivated for safety during setup procedures.

Attempting to use these controls will reactivate the information message.

Setup Mode

NOTE ALSO: •

In Engine HP Test, Drive Motor Setup, Drive Pump POR Setup, Drive Pump Regulation and Max Current Setup Modes the arch and boom are deactivated. Attempting to use these controls will reactivate the information message.

•

In Function Setup Mode the drive pedals and steering are deactivated. Attempting to use these controls will reactivate the information message.

Engine HP Test Mode for service use only.

Return to Normal Mode to operate machine.

Setup Mode Drive Motor Setup Mode for service use only.

Return to Normal Mode to operate machine.

For more information on the setup mode settings refer to COMPUTER – ADJUSTMENT MENU SERVICE SETTINGS – PROGRAM MODE in THIS SECTION.

Setup Mode Drive Pump POR Setup Mode for service use only. Return to Normal Mode to operate machine.

2.79

Controls and operation

Tigercat 610E/615E Skidder

Setup Mode Drive Pump Regulation Setup for service use only. Return to Normal Mode to operate machine.

Setup Mode Function Setup Mode for service use only.

Return to Normal Mode to operate machine.

Setup Mode Max Current Setup Mode for service use only.

Return to Normal Mode to operate machine.

2.80

Tigercat 610E/615E Skidder

Controls and operation

Machine Steering Steering invert disabled. Steer joystick direction does not change when operator is facing rearward.

MACHINE STEERING INVERT DISABLED This message will be displayed each time the machine is started when the joystick steering invert function is disabled.

When the joystick steering invert function is disabled. Steer joystick direction does not change when operator is facing rearward. Therefore LEFT articulation and RIGHT articulation are considered to be left and right as viewed by the operator from the forward facing seat position regardless of the position of the operator's seat.

For more information regarding the steer invert function setting refer to COMPUTER – ADJUSTMENT MENU - SERVICE SETTINGS – STEER INVERT (JOYSTICK STEERING ONLY) in THIS SECTION. Refer also to LEFT JOYSTICK – STEERING, ROTATING SEAT KICK LEVER and COMPUTER – MESSAGES - INFORMATION – MACHINE STEERING INVERT DISABLED in THIS SECTION.

2.81

Controls and operation CAB VENTILATION

Tigercat 610E/615E Skidder 1

1. AIR VENTS The Air Conditioner/Heater package has 8 air outlets in the cab.

• 2 in the top half of the left door post.

• 2 in the top half of the right door post.

• 2 on the rear dash, below the window.

• 1 behind seat on the lower right.

• 1 behind seat on the lower left.

NOTE: To increase flow to a given vent, other vents must be closed in order to redirect the air.

620E-026

RH DOOR POST VENTS - 2

2. FILTER, RECIRCULATING AIR - A/C UNIT Air in the cab is drawn into the A/C-HEATER unit via this filter and recirculated. The filter is located at the base of the A/C unit. It should be cleaned or replaced on a regular basis.

This is done by removing two thumb screws in the filter box cover.

1

REAR DASH VENTS - 2

620E-021

3. FILTER - FRESH AIR

2

When the air source switch is in the ON position , outside air is drawn into the cab air conditioning unit through this filter and mixed with interior air from the cab. To reduce dust in the cab area, use the FRESH AIR option with the A/C on. This pressurizes the cab, forcing dust out and reducing dust coming in. The FRESH AIR filter is accessible from outside of the cab, at the back between the lights. The filter should be inspected on a regular basis and cleaned/replaced when severely plugged or wet. This is done by removing 6 bolts (3/8”) and removing the air inlet cover. Next remove two nuts (1/4”) and remove the filter box cover. This will allow access to the filter.

1

620E-020

VENTS BEHIND SEAT - 2 3

WARNING - These filters may require cleaning or replacement more frequently under extreme operating conditions.

620E-019

2.82

FRESH AIR FILTER

Tigercat 610E/615E Skidder

Controls and operation LOCATED IN OPERATOR'S CAB

CHARGE GAUGE

620E-018

AM/FM STEREO CD With two front mounted speakers. Consult the manufactures instruction manual for additional information.

620E-006

FIRE EXTINGUISHER, PORTABLE

FIRE EXTINGUISHER, PORTABLE A portable fire extinguisher is located in the operator's cab. The extinguisher should be checked daily to ensure that it is charged. The pointer on the charge gauge should point to the green region. If the indicator falls out of this green area, the extinguisher should be serviced immediately. Refer also to FIRE PREVENTION in SECTION 1 of THIS MANUAL.

620E-028

RADIO - CB (IF EQUIPPED) Consult the manufacturer's instruction manual for additional information.

2.83

Controls and operation CAB FUSE AND RELAY PANEL

Tigercat 610E/615E Skidder

The fuse panel is located in the left rear of the cab behind the seat. The fuses and relays are protected beneath a panel which can be opened by removing two screws.

IMPORTANT 24 VOLT ELECTRICAL SYSTEM

620E-007

FUSE AND RELAY PANEL

CAB FUSE AND RELAY PANEL 2.84

Tigercat 610E/615E Skidder FUSES AND RELAYS (ELECTRICAL BOX)

Controls and operation

ELECTRICAL BOX (LEFT SIDE FRONT CHASSIS)

630E-298

3

100A

4

150A

5

60A

2 1

12

6 5.1K 7

14

16

9 10

13

15

17

8 5.1K 11

12345678910 11 12 13 14 -

18

20A

19

20A

20

20A

21

15A

22

15A

23

5A

24

30A

15 16 17 18 19 20 21 22 23 24 -

GRID HEATER SOLENOID FILL PUMP SOLENOID CAB POWER GRID HEATER FILL PUMP HYDRAULIC OIL TEMP SPARE CHARGE FILTER BY-PASS SPARE SPARE SPARE ENGINE ECU RELAY ATS RELAY AFTER RUN DISCONNECT RELAY STARTER SOLENOID RELAY DEF HEATED LINES RELAY FUEL HEATER RELAY ATS SENSORS EXHAUST FLAP DEF HEATED LINES FUEL HEATER 2 FUEL HEATER 1 FILL PUMP SWITCH ECU POWER

62726BENG R1

ELECTRICAL BOX FUSES AND RELAYS 2.85

Controls and operation

Tigercat 610E/615E Skidder

CHASSIS

BOLT ON ACCESS PANELS

BOLTS

MAINTENANCE ACCESS DOORS

610E-025

ACCESS PANELS LEFT SIDE

BOLT ON ACCESS PANELS

620D-208

FRONT DOOR

DOORS AND ACCESS PANELS FRONT DOOR TO OPEN: Park machine on level ground and lower the grapple and dozer to the ground.

Remove the two bolts from the left side of the door and swing open.

When the maintenance is complete, close the door and reinstall bolts.

MAINTENANCE ACCESS DOORS

Do not operate DOZER with door open.

If the ground is not level, ensure that the door swings towards the downhill side to prevent it from swinging closed on the operator/mechanic.

610E-003

CAUTION Park on level ground to prevent unexpected door closing.

2.86

ACCESS PANELS RIGHT SIDE

Tigercat 610E/615E Skidder ACCESS PANELS

Controls and operation

This machine is equipped with bolt on access panels to provide service access.

DOOR PROP

610E-023

MAINTENANCE ACCESS DOOR (RIGHT SIDE SHOWN)

Some panels are equipped with a maintenance access door to provide quick access for routine daily maintenance. Maintenance access doors are equipped with a door prop to hold them open while in use as shown above.

Always ensure that all access panels are secured in place and all access doors are closed and secured before operating the machine.

CAUTION Always use the door props provided to safely hold access doors open while in use.

The engine compartment access panels are bolted in place. Whenever bolts are removed panels can fall during the process of removing them from the machine.

2.87

Controls and operation

610E-026

Tigercat 610E/615E Skidder

STANDARD FUEL TANK

FUEL TANK Located in the rear chassis, the fuel reservoir consists of two tanks interconnected. There is one filling location (right tank). The fill tube also contains a fuel strainer.

The fuel strainer located under the fill cap should be removed and cleaned every 125 Hours (reach in and lift it out). Replace the screen if it is damaged.

A sending unit is installed and connected to the computer display on the instrument panel.

The standard fuel tank has a capacity of 81 US gal (305 L).

There is also a high capacity fuel tank available for machines without winches. It is a single 114 US gal (430 L) replacement tank.

HIGH CAPACITY FUEL TANK 620D-212 REFUELLING Park machine on level ground, turn the engine off and allow machine to cool.

DO NOT refuel while smoking or near an open flame or sparks.

Clear obstructions from steps and handles needed to access fuel tank.

Open cover on top of fuel tank (if equipped)and clear any debris from around the fuel fill cap.

Remove fuel fill cap slowly to allow pressure to escape from tank.

Inspect fuel fill cap gasket.

Inspect fuel strainer located under the fill cap for debris or damage.

Attach a grounding strap to an unpainted metal surface on the machine if the refuelling tank or nozzle is so equipped.

Fill tank until fuel level reaches the fuel strainer or the full mark on the sight gauge if equipped. Do not leave nozzle unattended or spillage may occur.

S≤15 mg/kg ULTRA LOW SULFUR FUEL ONLY 36686AUNI R0

Remove nozzle and ground strap (if applicable), then install fuel fill cap hand tight before closing fill cap cover.

Before restarting the machine, check that no other personnel have moved into the hazardous area and sound the horn.

2.88

Tigercat 610E/615E Skidder DIESEL EXHAUST FLUID (DEF) TANK

Controls and operation

The DEF tank is located in the compartment below the right hand cab door. It is accessible through an access cover at the top of the compartment for filling. The DEF tank fill point is equipped with a filter to prevent contaminants from entering the tank.

DEF TANK (BLUE FILL CAP)

41581AUNI R0

DEF tank capacity is 43 L (11.4 US gal). DO NOT overfill tank. This tank is equipped with an expansion capacity of 7% required to allow for the expansion of DEF in cold temperature conditions.

DEF freezes at -11°C (12°F).

A DEF level indicator is shown on the main menu of the computer display, below the fuel gauge.

When DEF levels are low information messages will be shown on the computer display. Note that extremely low DEF levels may result in derating of engine performance to meet emission standard requirements. Action to correct DEF levels should be taken immediately to avoid affecting engine performance. Refer also to COMPUTER – MESSAGES in THIS SECTION. The DEF tank and DEF supply lines are heated when temperatures are low, the system will thaw DEF within 30 minutes of engine start for proper operation of the diesel oxidation catalyst /selective catalytic reduction (DOC/SCR) aftertreatment system. Note also that whenever the engine is stopped all DEF is pumped back to tank before the engine power system is turned off. This process takes approximately 90 seconds. Refer to AFTERTREATMENT SYSTEM in SECTION 3 of THIS MANUAL. Diesel exhaust fluid (DEF) is an aqueous urea solution with 32.5% high purity urea and 67.5% deionized water. Note that DEF may also be referred to as AUS32 or AdBlue and should meet ISO 22241 specifications. Use only DEF meeting this standard.

WARNING

Use only diesel exhaust fluid (DEF) which meets ISO 22241 specifications. NEVER fill the DEF tank with any other fluid.

DEF fluid is injected into the exhaust gas stream during normal operation of the Selective Catalytic Reduction (SCR) aftertreatment system.

Use of other fluids may cause component damage, or a fire risk which could result in death or serious injury.

610E-005

DEF TANK

DEF is used by the DOC/SCR aftertreatment system to lower the concentration of nitrogen oxides from the diesel engine exhaust of this vehicle.

It is important to avoid contamination of DEF when filling the tank as this may cause costly damage to aftertreatment system components and affect the proper operation of aftertreatment system and the engine.

When a problem with DEF quality is detected information messages will be shown on the computer display. Note that DEF quality problems may result in derating of engine performance to meet emission standard requirements. Action to correct DEF quality problems should be taken immediately to avoid affecting engine performance and damage to DOC/SCR aftertreatment system components. Refer also to COMPUTER – MESSAGES in THIS SECTION. IMPORTANT! DEF should be stored between -11°C (12°F) and 30°C (86°F) and out of direct sunlight to maximize shelf life and to avoid DEF quality problems caused by improper storage.

Refer also to AFTERTREATMENT SYSTEM in SECTION 3 of THIS MANUAL for more information regarding the use of DEF and its function in the DOC/SCR aftertreatment system.

2.89

Controls and operation

Tigercat 610E/615E Skidder

BATTERY DISCONNECT SWITCH

630E-297

BATTERY DISCONNECT SWITCH LEFT SIDE ENGINE COMPARTMENT

BATTERY DISCONNECT SWITCH

Located in the engine compartment on the left side of the machine, this switch is wired to the positive side of the battery.

When in the OFF position it completely disconnects all the machine's electrical circuits from the battery and isolates the engine electronic control unit (ECU) power fuses.

Note that this machine is equipped with an After Run/ Accessory Relay which delays by 90 seconds the power disconnect to engine related fuses and relays. Whenever the engine is stopped all DEF solution is pumped back to tank before the engine power system is turned off. This process takes approximately 90 seconds. Refer to AFTERTREATMENT SYSTEM in SECTION 3 for more information.

BELOW RIGHT HAND CAB DOOR

TRANSMISSION OIL FILL CAP

TRANSMISSION DIPSTICK

610E-006

TRANSMISSION DIPSTICK AND FILL LOCATION

TRANSMISSION DIPSTICK The transmission dipstick is located below the right hand cab door.

TRANSMISSION OIL FILL LOCATION The transmission oil fill cap is located below the right hand cab door.

2.90

Tigercat 610E/615E Skidder PRESSURIZED WATER SYSTEM (IF EQUIPPED) WATER WATER TANK CONTROL VALVE

SHUT-OFF VALVE IN CLOSED POSITION 620E-004

Controls and operation

DOZER BLADE

HOSE STORAGE COMPARTMENT

PRESSURIZED WATER SYSTEM

A water tank is incorporated into the dozer blade and is pressurized to 60 psi (4 bar). A valve controls the flow of water from the tank to a hose located in the hose storage compartment on the dozer blade.

The control valve incorporates an air charge valve, a pressure gauge and a relief valve on the outlet side of the valve. A ball valve is installed on the outlet side of the valve and is used to shut off the water supply to the hose. This shut-off valve should be in the CLOSED position when the system is not in use.

The pressure gauge on the valve should read 60 psi (4 bar) check system pressure daily.

Refer to PRESSURIZED WATER SYSTEM MAINTENANCE in SECTION 3.

All handles should be hand tight only at all times.

This is particularly important for easy access to the pressurized water system in the event of a fire or other emergency.

Refer also to FIRE PREVENTION in SECTION 1 of THIS MANUAL. 2.91

Controls and operation ENGINE AIR CLEANER

Tigercat 610E/615E Skidder

ENGINE AIR PRECLEANER

IMPORTANT !

For peak engine performance and maximum fuel economy, please ensure that the air precleaner is regularly checked and cleaned as required. All intake air tubes and clamps should be thoroughly inspected on a regular basis and any damaged or missing components should be replaced immediately.

3

3 4 610E-035

ENGINE AIR PRECLEANER

AIR PRECLEANER

2

The engine air precleaner cleans engine air before it reaches the air cleaner filter elements.

It removes contaminants such as dust, powder, insects, rain and snow. The air precleaner should be checked every 8 hours to make sure that foreign materials have not plugged the intake area or the discharge louver area. Clean as required.

IMPORTANT !

The air precleaner must be check every 8 hours and cleaned as required.

If the inlet/precleaner is plugged causing a restriction to airflow, reduced engine performance and increased fuel consumption may result.

If a plugged inlet/precleaner is left too long excessive air intake restriction may damage the rubber air intake tube. A damaged air intake tube will lead to ingestion of dirt into the engine which may result in engine failure.

1 5

630C-19

CENTRI® PRECLEANER OPERATION

OPERATION: 1. Air enters the precleaner.

2. Specially designed vanes move dirty air toward the impeller.

3. The spinning impeller spins the air creating centrifugal force to separate contaminants from the clean air.

4. Contaminants are blown out the discharge louver.

5. Clean air enters the intake to the air cleaner.

Note that the air filter restriction indicator may not function properly if the air intake tube is damaged.

Engine failures due to improper maintenance are not covered by Tigercat or Engine Manufacturer’s Warranty and any such claim will be denied.

2.92

Tigercat 610E/615E Skidder

Controls and operation This valve should be replaced every 1000 hours.

Remove the unloader valve from the tube of the air cleaner housing. Check and clean the valve.

A good valve should be soft and flexible. If it is plugged, be sure to check the filter elements as they may need replacing as well. Reattach the valve to the tube.

AIR CLEANER

When operating in high dust conditions, the unloader valve should be checked and squeezed every 2 hours to release dust buildup.

AIR CLEANER UNLOADER VALVE

FILTER RESTRICTION INDICATOR A filter restriction indicator is connected to the outlet side of the air filter. Replace the primary air filter when the indicator shows RED. This indicator provides a continuous reading whether the engine is running or is turned off. After replacing the filter, reset the indicator by pressing the reset button.

ENGINE AIR CLEANER AIR CLEANER 610E-007

The air cleaner on this machine uses two filter elements, a primary element and a safety element accessible from the left side of the engine compartment.

To ensure maximum engine protection, it is important that the elements be serviced correctly and at proper servicing intervals.

A filter restriction indicator is mounted to the output side of the filter, this should show green when the engine is running under load. Service is required if the indicator shows red. This machine is also equipped with a switch used to send a signal to the computer control system in the event of a filter restriction.

Engine Air Intake Filter Restricted. Service Machine to correct.

FILTER RESTRICTION SWITCH

AIR CLEANER

FILTER RESTRICTION INDICATOR

610E-008

ENGINE AIR CLEANER

NOTE: Replace the safety element every third primary filter change.

In addition refer to the LUBRICATION AND MAINTENANCE SCHEDULE and AIR CLEANER MAINTENANCE in SECTION 3 of THIS MANUAL

When a signal is received from the restriction indicator switch on the engine air cleaner a warning message will be displayed. Refer to COMPUTER – MESSAGES - ALERT – ENGINE AIR INTAKE FILTER RESTRICTED in THIS SECTION. AIR CLEANER UNLOADER VALVE This rubber valve on the tube of the air cleaner housing should be checked at the beginning of every shift (8 hours). If this valve is missing, damaged or has become hard, it will cause the air cleaner to become ineffective. The valve should suck closed at 1/3 throttle 2.93

Controls and operation MAIN HYDRAULIC OIL TANK

Tigercat 610E/615E Skidder HYDRAULIC TANK

Located at the rear of the engine compartment.

Refer to SERVICE AND LUBRICATION POINTS chart in SECTION 3 of THIS MANUAL for hydraulic tank capacity.

DOUBLE ELEMENT FILTER

A sight gauge accessible through the right rear access panel, indicates the HIGH and LOW level of the main hydraulic oil tank.

BREATHER

BLUE ELEMENT

Always keep the hydraulic oil level between the HIGH and LOW calibrations. A low hydraulic oil level can result in severe damage to pumps.

SIGHT GAUGE

Check hydraulic oil level and fill tank with grapple head fully open, grapple head and dozer blade on the ground. Fill tank until hydraulic oil level reaches the sight gauge full mark. Note that the oil level will drop 2 to 3 in (2 to 7.5 cm) when all cylinders are extended.

LEVEL SWITCH

CHARGE PRESSURE FILTER

A hydraulic oil level switch is connected to the computer control system. The hydraulic oil level switch is incorporated into the base of the sight gauge. This switch triggers the hydraulic oil level low warning.

Refer also to COMPUTER – MESSAGES CRITICAL – HYDRAULIC OIL LEVEL LOW in THIS SECTION.

610E-016

HYDRAULIC TANK, FILTERS AND SIGHT GAUGE

HYDRAULIC FILTERS The hydraulic cooling circuit contains a two element, full flow, 7 micron filter with a built in 25 psi (1.7 bar) bypass valve. It is recommended that all machines use two different filter elements: 1 blue, Tigercat water absorbing, full flow hydraulic oil filter element.

SIGHT GAUGE

1 white, Tigercat high performance, full flow hydraulic oil filter element.

The charge circuit contains a single element, full flow, Tigercat hydraulic filter with a restriction indicator sending unit and a third port bypass valve.

For additional information on these filters refer to FILTERS and SERVICE AND LUBRICATION POINTS in SECTION 3.

610E-017

2.94

MAIN HYDRAULIC OIL SIGHT GAUGE

Tigercat 610E/615E Skidder

Controls and operation

HYDRAULIC FILL PUMP The electric hydraulic fill pump, located under the drive pump, is used to add oil to the hydraulic oil tank. The pump switch is located on the right side at the front of the engine compartment.

QUICK CONNECT TO SUCTION HOSE

LOCATED ON THE RIGHT SIDE AT THE FRONT OF THE ENGINE COMPARTMENT

Refer to APPROVED HYDRAULIC OILS in SECTION 3 of THIS MANUAL. Refer to SERVICE AND LUBRICATION POINTS chart in SECTION 3 of THIS MANUAL for hydraulic tank capacity.

PUMP SWITCH

TO ADD OIL TO THE MAIN HYDRAULIC TANK: 1. Park machine on level ground, lower dozer blade and grapple (with head fully open) onto the ground.

610E-009

HYDRAULIC FILL PUMP

610E-018

HYDRAULIC FILL PUMP

2. Open right front engine compartment access door.

3. Get the hydraulic oil fill suction hose from its storage location. Clean the suction hose, connect to hydraulic fill pump and remove cap.

Insert end of suction tube into supply drum.

4. Operate pump using the pump switch, located on the right side at the front of the engine compartment. The oil is pumped directly into the hydraulic tank via the double element filter.

5. Observe the level gauges on the rear of the tank to determine when to release the switch.

Fill tank with grapple head fully open, grapple head and dozer blade on the ground. Fill tank until hydraulic oil level reaches the sight gauge FULL mark. Note that the oil level will drop 2 to 3 in (2 to 7.5 cm) when all cylinders are extended.

HYDRAULIC OIL FILL SUCTION HOSE STORAGE LOCATION

6. Replace cap on suction tube, wipe dry, disconnect and store. Close all access doors.

IMPORTANT !

Contaminated hydraulic oil can lead to premature failure of hydraulic components and costly repairs.

Filters must be replaced at the recommended time intervals. Refer to SCHEDULED MAINTENANCE in SECTION 3 of THIS MANUAL. Use of hydraulic filters other than the Tigercat brand could lead to severe wear and rapid failure of hydraulic system components.

620E-050

2.95

HYDRAULIC OIL FILL SUCTION HOSE STORAGE LOCATION BELOW LEFT HAND CAB DOOR

Controls and operation

Tigercat 610E/615E Skidder

OPERATING MACHINE Before operating this machine, ensure that the proper lubrication and maintenance schedule has been performed as outlined in SECTION 3 of THIS MANUAL. For the Diesel Engine supplied with this machine, refer to the engine manufacturer's operating manual.

3. When computer checks are complete place ignition switch in the OFF position.

Any personnel who are to operate this machine must be fully trained in safety and operating procedures by a competent person.

Read and understand the entire manual before operating the machine.

PRESTART CHECKS:

610E-026

STANDARD FUEL TANK

4. Check fuel gauge. Refer to FUEL TANK in THIS SECTION for standard tank capacity information.

1. Place the ignition switch in the RUN position (engine NOT running). Check for any alarms noted on the computer display and investigate the cause. Refer to COMPUTER in THIS SECTION. ICON ILLUMINATED (RED) WHEN PARKING BRAKE IS ENGAGED

2. Check parking brake for proper operation and engage parking brake.

SIGHT GAUGE

610E-017

MAIN HYDRAULIC OIL SIGHT GAUGE

5. Check hydraulic tank oil level with grapple head fully open, grapple head and dozer blade on the ground. In this position the oil level should reach the full mark. Note that the oil level will drop 2 to 3 in (2 to 7.5 cm) when all cylinders are extended.

2.96

Tigercat 610E/615E Skidder

Controls and operation

DIPSTICK

HAND PRIMER

LEFT SIDE OF ENGINE

SECONDARY FUEL FILTER/ WATER SEPARATOR

ENGINE OIL LEVEL 6. Check the engine oil level. The level of the oil must be between the ADD and the FULL marks on the dipstick.

630E-297

BELOW RIGHT HAND CAB DOOR

WATER IN FUEL SENSOR DRAIN VALVE

TRANSMISSION OIL FILL CAP

FUEL WATER SEPARATOR 8. Drain water from fuel line water separator.

630E-291

TRANSMISSION DIPSTICK

610E-006

TRANSMISSION DIPSTICK AND FILL LOCATION

RADIATOR FILL CAP

7. Check transmission oil level. The level of the oil must be between the ADD and the FULL marks on the dipstick.

33952AUNI R0

620E-025

ENGINE COOLANT LEVEL

9. Check the engine coolant level.

2.97

Controls and operation

Tigercat 610E/615E Skidder

ENGINE AIR PRECLEANER A/C COMPRESSOR BELT

SERPENTINE BELT

ENGINE AIR PRECLEANER 610E-035 11. Check air intake precleaner for foreign material build-up in air intake area or discharge louver area.

AIR CLEANER

620E-058

CHECK CONDITION OF ENGINE BELTS

10. Check tension and condition of all engine belts.

AIR CLEANER UNLOADER VALVE

610E-007

ENGINE AIR CLEANER

12. Check air cleaner unloader valve (if equipped)

2.98

Tigercat 610E/615E Skidder AIR CLEANER

Controls and operation

FILTER RESTRICTION SWITCH

WATER WATER TANK CONTROL VALVE

DOZER BLADE

FILTER RESTRICTION INDICATOR

ENGINE AIR CLEANER 610E-008 13. Check engine air cleaner restriction indicator.

SHUT-OFF VALVE IN CLOSED POSITION 620E-004

HOSE STORAGE COMPARTMENT

PRESSURIZED WATER SYSTEM

15. Check pressurized water system (if equpped).

The pressure gauge should read 60 psi. This system should be tested once every month.

Refer to PRESSURIZED WATER SYSTEM MAINTENANCE in SECTION 3 of THIS MANUAL. 16. Perform SCHEDULED MAINTENANCE as shown in SECTION 3 of THIS MANUAL. 17. Inspect machine for leaks , damaged or loose components and any other abnormal conditions.

18. Check tire pressures.

19. Check wheel bolts for tightness.

20. Be sure that all covers, guards and doors are securely fastened.

21. Unlock all cab doors.

620E-059

IMPORTANT! Unlock both doors before operating machine to allow opening from the outside in case of an emergency. Make sure that the doors are operational, open the doors twice, once using the exterior handle and once using the interior latch handle.

CLEAN RADIATOR, OIL COOLER, CAC AND A/C CONDENSER

14. Clean radiator, oil cooler, CAC (charge air cooler) and A/C condenser. Remove debris from front door and screened access panels on both sides of the machine.

Refer to CLEANING A/C CONDENSER AND COOLING ASSEMBLY in THIS SECTION.

2.99

Controls and operation STARTING ENGINE

Tigercat 610E/615E Skidder IMPORTANT !

After engine has started, keep engine speed low until engine oil pressure registers on computer display. If engine oil pressure does not register within 10 seconds, stop engine and investigate cause.

1. Ensure that PRESTART CHECKS have been performed and that the area is clear of personnel prior to starting the engine.

2. Parking brake ENGAGED. NOTE: The engine will not turn over unless the parking brake is ENGAGED.

NOTE: If the engine does not start after three attempts, check the fuel supply system.

Absence of blue or white exhaust smoke during cranking indicates no fuel is being delivered.

3. Turn ignition key to RUN position and observe computer display.

CAUTION Do not start engine by shorting across starter terminals. Start engine only from operator's seat.

If engine stalls while operating the machine, turn the ignition key to the OFF position and REPEAT STEPS (1) THROUGH (6).

8. Before applying any load to the engine proceed with SYSTEM TEST AND WARM UP. IMPORTANT !

Allow a cold engine to warm up at LOW IDLE for at least five minutes before applying any load. Check all gauges often during the warm up period.

4. Wait for WAIT TO START warning on computer display to turn off.

NOTE: For cold weather conditions refer to MACHINE WARM UP OPERATION on the following pages.

5. Sound horn to warn personnel of machine start-up.

6. Turn ignition key switch to the START position to crank the engine. When engine is started place key switch in RUN position and observe computer display.

IMPORTANT !

Note that the computer control system will automatically perform a bulb test when the keyswitch is released to the RUN position.

The alarm light will flash and the master alarm will sound briefly to test for proper operation.

7. Engine idle speed setting will automatically default to LOW IDLE. Keep engine speed low until engine oil pressure registers on computer

Engine should not idle longer than 9 consecutive hours. Damage to the emission control system will result. When this machine idles for an extended period excess hydrocarbon buildup is created in the DOC/SCR aftertreatment system. Burn off of excess hydrocarbon at full load immediately after a long idle period will generate excess heat which will cause damage to emission control system components.

display ( ENGINE MENU - ENGINE FUNCTIONS). Low engine oil pressure will trigger an alarm.

Refer to COMPUTER – MESSAGES CRITICAL – ENGINE OIL PRESSURE LOW.

2.100

Tigercat 610E/615E Skidder STARTING IN COLD WEATHER

Controls and operation

NOTICE

Cold temperatures may require the use of the engine block heater and the engine oil pan heater.

The engine is equipped with an intake air heater with a grid element.

WARNING: Using starting fluid (or ether start aids) on an engine equipped with a grid heater element can cause an explosion. NEVER USE STARTING FLUIDS on an engine equipped with a grid heater element.

WARNING • EXPLOSION HAZARD.

• DO NOT IDLE THIS ENGINE FOR MORE THAN 9 HOURS. • DAMAGE TO EMISSION CONTROL SYSTEM WILL RESULT.

• DO NOT USE ETHER. • ENGINE EQUIPPED WITH HEATER STARTING AID. • USE OF ETHER COULD RESULT IN DEATH OR SERIOUS INJURY.

63281BENG R0

36782BENG R0

The grid element preheats engine intake air during cold starts. The wait to start warning is shown on the computer display for the duration of the preheating phase of engine start-up. To minimize cranking time during cold weather starts, ALWAYS wait for the wait to start warning on the computer display to turn off before cranking the engine.

Before applying any load to the engine proceed with SYSTEM TEST AND WARM UP.

IMPORTANT !

Engine should not idle longer than 9 consecutive hours. Damage to the emission control system will result. When this machine idles for an extended period excess hydrocarbon buildup is created in the DOC/SCR aftertreatment system. Burn off of excess hydrocarbon at full load immediately after a long idle period will generate excess heat which will cause damage to emission control system components.

IMPORTANT !

To prevent damage to starter, do not engage starter motor for more than 15 to 20 seconds.

Wait 2 minutes between each attempt to start the engine. If engine fails to start, refer to engine manufacturers operator's manual.

NOTE: This engine is equipped with a STARTER LOCKOUT feature that prevents the starter motor from being engaged before the engine ECU is online, before the WAIT TO START warning on the computer display is OFF and when the engine is already running.

IMPORTANT !

Cold starts can result in pump failure, refer to "APPROVED HYDRAULIC OILS" in SECTION 3 for recommended oil viscosities and temperature ranges.

NOTE: For cold weather conditions refer to MACHINE WARM UP OPERATION on the following pages.

2.101

Controls and operation MACHINE WARM UP OPERATION

Tigercat 610E/615E Skidder

The MACHINE WARM UP function is provided to increase engine idle speed to assist in warming the engine and cab temperature in cold weather conditions.

NOTE: To set the MACHINE WARM UP function ON the engine must be running and the parking brake must be ENGAGED. Disengaging the parking brake will turn the MACHINE WARM UP function OFF.

TO TURN MACHINE WARM UP FUNCTION OFF: When engine and cab have warmed to the desired temperature, the machine warm up function can be turned off by pressing the F1 ( ) button again (at the engine display screen) or by disengaging the parking brake.

TO TURN MACHINE WARM UP FUNCTION ON:

From the main menu press the F1 button to select the engine display.

Press the F1 button to toggle the machine warm up function ON/OFF. The machine warm up icon at the top of the screen is illuminate when the machine warm up function is ON. Refer to MACHINE WARM UP SPEED ADJUSTMENT in THIS SECTION to adjust machine warm up speed setting if required.

2.102

Tigercat 610E/615E Skidder MACHINE WARM UP SPEED ADJUSTMENT

Controls and operation

Press the arrow up or arrow down buttons to scroll to the setting to be adjusted.

From the main menu press F2 button to select the ADJUSTMENT MENU.

Press the F2 button to reset to default setting.

Press F2 (Yes) or F3 (No) to confirm.

The engine settings menu will appear by default.

Continued on next page

Press F1 (Adjust) to adjust engine settings

2.103

Controls and operation

Tigercat 610E/615E Skidder

OR

OR

Press the OK button to go to the adjustment display.

To reset to default setting press the F2 button.

Press F2 (Yes) or F3 (No) to confirm.

Press the arrow up or arrow down buttons to make the adjustment.

Press the back button to return to the adjustment menu.

Press the OK button to confirm the setting.

Press the back button again to return to the main menu.adjustment menu.

Press the back main menu.

2.104

button again to return to the

Tigercat 610E/615E Skidder SYSTEM TEST AND WARM UP

Controls and operation (l) Engage the parking brake. (m) Decrease engine idle speed to LOW IDLE.

Before commencing skidding operations, follow steps (a) through (n) to accomplish the following:

CAUTION

• Warm up the hydraulic system.

• Test all systems for proper operation.

• Inspect for hydraulic oil leaks.

Ensure that the machine was parked on level ground at last shutdown:

Never use your bare hand to check for fluid leaks.

Fluid leaks under pressure may not be visible. When searching for leaks, wear work gloves and use a wrench or piece of wood to move hydraulic hoses. Do not grab hold of hydraulic hoses. Wear safety goggles for eye protection.

(a) Start engine. (b) Ensure that computer displays are indicating normal operating conditions. (c) Check that all personnel are clear of the machine. Disengage the parking brake. (d) Slowly raise and lower the arch, check for proper operation.

(n) Leave the cab and visually check hose connections and cylinders for leaks. Check under the machine for oil leaks.

With the grapple and dozer raised slightly off the ground: (e) Operate the grapple arms and check for proper operation. (f) Rotate grapple in each direction for several revolutions and check that it is operating correctly. (g) Raise and lower dozer blade (h) Steer the machine to the left and right. (i) When cold weather conditions exist, continue the process of warming up the hydraulic system by repeating steps (e) through (h) several times. As the hydraulic system warms up, engine speed can be increased gradually to the HIGH IDLE. (j) Observe all operations. If any operations are not functioning as they should, take the necessary steps to correct the problem.

After completion of the warm up and system testing, lower the dozer blade and grapple to the ground. (k) Check service brake for proper operation.

Refer to SERVICE BRAKE – CHECKING BRAKE AND ACCUMULATOR FOR PROPER OPERATION in SECTION 3 of THIS MANUAL.

2.105

Controls and operation STOPPING ENGINE:

Tigercat 610E/615E Skidder RESTARTING AN ENGINE THAT HAS RUN OUT OF FUEL

CAUTION

If the engine runs out of fuel, the fuel line is self priming.

Stopping the engine immediately after it has been working under load can result in overheating and premature wear of the engine components. Follow the stopping procedure outlined below to allow the engine to cool.

1. Refill fuel tank completely.

2. Turn ignition key to RUN position and observe computer display.

3. Wait for WAIT TO START warning on computer display to turn off.

1. Park machine on level ground and lower grapple and dozer blade to the ground.

2. Reduce engine speed to LOW IDLE and let run for approximately three to five minutes to allow gradual dissipation of heat and also to reduce turbo speed. This will also prevent loss of coolant by after boil and possible hot spot damage to the engine.

4. Turn ignition switch to the START position to crank engine.

If it fails to start after 20 seconds, stop and wait for 2 minutes before trying again.

5. When engine starts, release ignition key to RUN position and observe the computer display.

3. Do not race engine before it is turned off.

IMPORTANT !

To prevent damage to starter, do not engage starter motor for more than 15 to 20 seconds.

Wait 2 minutes between each attempt to start the engine.

4. Parking brake ENGAGED. 5. Stop engine by turning ignition switch to the OFF position.

Note that whenever the engine is stopped all DEF solution is pumped back to tank before the engine power system is turned off. This process takes approximately 90 seconds. Refer to AFTERTREATMENT SYSTEM in SECTION 3 for more information.

If engine fails to start, refer to engine manufacturers operator's manual.

WARNING Before leaving the machine, park it in a safe position on level ground. Lower the grapple and dozer blade to the ground and engage parking brake.

Never work behind, in front of, or below a skidder that has been parked on a grade.

Take additional precautions by placing the wheels against a rock, tree or other secure object.

Note also that this machine is equipped with an After Run/ Accessory Relay which delays by 90 seconds the power disconnect to engine related fuses and relays.

WARNING When leaving the cab, always lower the dozer blade to the ground, engage the parking brake and turn the ignition switch OFF. If leaving the Skidder unattended, also remove the ignition key and switch the battery disconnect switch to OFF

2.106

.

Tigercat 610E/615E Skidder TRAVELLING WITHOUT A LOAD:

Controls and operation Refer to STEERING in THIS SECTION for more detailed steering control information.

Raise the grapple and place the dozer blade in the UP position.

(5) Use differential locks sparingly and ONLY when additional traction is required.

Never continuously drive the machine with the differential locks on. Serious damage to the axles can result from using the differential locks when they are not needed for additional traction.

(1) Disengage parking brake. NOTE: Machine will not move if the parking brake is not fully off.

(2) Check the position of the maximum speed control to ensure that it is set to the desired position.

Note: This machine is equipped with a 10 minute AUTO-OFF feature which automatically deactivates the differential locks after 10 minutes have passed.

Using the maximum speed control the operator is able to set the maximum travel speed of the machine. This allows the operator to maintain any desired travel speed with full drive pedal operation. Machine travel speed reduction can still be achieved by not fully depressing the foot pedal.

This control can be used while the machine is in motion.

Caution: Setting the maximum speed control to the minimum setting lowers maximum travel speed only, it will NOT prevent the machine from travelling when the forward or reverse travel controls are used.

NOTE: The high idle adjust function is available.

This function is intended to allow the automatic reduction of the engine high idle speed limit when travelling without a load. Refer also to COMPUTER – ADJUSTMENT MENU - ENGINE SETTINGS – ENGINE HIGH IDLE ADJUST in THIS SECTION.

(3) ROTATING SEAT & JOYSTICK STEERING

Use the direction selection switch on the left joystick to choose forward or reverse and press the travel foot pedal to move the machine in that direction.

STATIONARY SEAT & STEERING WHEEL

Operate the drive travel pedals to move the machine forward or reverse.

(4) Be aware of the type of steering control (and steer valve option - if applicable) the machine is equipped with. Steering control operation varies with the type of controls in use.

Generally, this machine is equipped with Load Sensing Steering. The speed that the vehicle responds to steering control input will vary, depending on the speed that the steering control is moved.

When operating on the road, a slow movement of the steering control will not overcorrect and will steer a straight normal course.

Operating in the woods requires quick steering changes and this is produced by a rapid movement of the steering control, which will quickly change the vehicles direction.

2.107

Controls and operation OPERATING GRAPPLE:

Tigercat 610E/615E Skidder CENTRE JOINT:

DAILY INSPECTION/SERVICE

It is very important that the machine not be operated if there is any looseness in the centre joint bearings.

Check the Operator’s Manual for your Grapple Lubricate all grease fittings

Refer to MAINTENANCE OF THE CENTRE JOINT in SECTION 3 of THIS MANUAL for visual checking procedures.

Check all hydraulic fittings Check hoses for wear. Replace as required.

For further information regarding adjustment and maintenance of the centre joint refer to CENTRE JOINT in SECTION 11 of the SERVICE MANUAL.

Check for excessive wear at pin points.

Inspect for trash accumulation and clean out.

Check for excessive head swing and tighten the snubber to prevent damage to grapple or arch.

620E-015

TYPICAL TIGERCAT GRAPPLE

OPERATION Grapple operations should always be performed while seated in the operator’s seat.

The controls will return to neutral automatically when released.

The Constant Pressure button on the joystick will provide a constant closing pressure to the tongs to take up the slack as the logs are lifted and settle together. This pressure is released when the grapple is opened.

Refer to RIGHT JOYSTICK in THIS SECTION for specific information on grapple operating controls.

2.108

Tigercat 610E/615E Skidder OPERATING WINCH:

Controls and operation dynamic brake for dropping a load on the fly or drive away from a load with slight tension on the cable. The control lever will return to the centre neutral position when released.

Place the skidder in a safe, stable location, in line with the load.

Lower the grapple and dozer blade to the ground to anchor the machine.

FOR ALLIED WINCH Place the winch select switch in the (freespool) position. The winch freespool icon on the main menu of the computer display will be illuminated.

FOR CARCO WINCH Place the winch select switch in the (freespool) position. The winch freespool icon on the main menu of the computer display will be illuminated.

This will allow the cable to unwind freely from the drum and also disconnects the drive motor from the drum in the winch and allow the cable to be freely pulled from the spool by hand. The freespool function is intended for use in pulling the cable by hand only and must not be used when the cable is loaded. Improper use of the freespool function will result in damage to the winch.

Make sure the cable is running freely through the fairlead rollers.

WARNING When operating Carco winches the load MUST be removed from the cable before placing the winch control in the freespool position to avoid damage to the winch which could cause a safety hazard.

Attempting to engage or disengage the freespool function with a load on the cable will cause damage to clutch halves, piston, final planetary gearing and/or output shaft.

Damage to freespool components can cause a sudden loss of load control which could result in death or serious injury.

This will allow the cable to unwind freely from the drum and also disconnects the drive motor from the winch drum.

Make sure the cable is running freely through the fairlead rollers.

Avoid winching at an angle to the skidder.

Pull the cable from the drum and attach to object.

Safety gloves should be worn.

To retrieve the cable: Close cab door and disengage parking brake.

Place the winch select switch (to the left of the lever) in the I (ON) position. Pull and hold the lever BACK to wind in the winch cable. For safety reasons this lever returns to the neutral (centre) position when released and actuates the brake, which locks the drum.

Avoid pulling the hook over the drum and through the throat of the winch.

Refer also to WINCH SELECT SWITCH and WINCH CONTROL LEVER in THIS SECTION.

Avoid winching at an angle to the skidder.

Pull the cable from the drum and attach to object.

Safety gloves should be worn.

To retrieve the cable: Close cab door and disengage parking brake.

Place the winch select switch (to the left of the lever) in the I (ON) position. Pull and hold the lever BACK to wind in the winch cable. For safety reasons this lever returns to the neutral (centre) position when released.

Avoid pulling the hook over the drum and through the throat of the winch.

To use the driveaway function: Place the winch select switch (to the left of the lever) in the I (ON) position. Push and hold the winch control lever FORWARD to release the 2.109

Controls and operation SKIDDING

Tigercat 610E/615E Skidder SKIDDING TECHNIQUE

WARNING

For more safety related information see also the Equipment Manufacturers Institute (EMI) Log Skidder Safety Manual for Operators and Mechanics supplied with this machine.

•

Only operate in areas where Skidder will be in a stable condition

SAFETY:

•

1. Know all Federal, State/Provincial and local rules which apply to your machine and job site.

Avoid felling and bucking areas. Sound your horn when entering.

•

Never travel across a STEEP slope or side hill.

•

Never make an uphill turn on a slope

2. NEVER operate this machine while under the influence of drugs or alcohol.

•

3. Know the limitations of your Skidder and Yourself as an operator.

Never approach an unstable log from the downhill side.

•

4. Check the work area for HAZARDS, both at ground level and overhead.

Do not work below machines that are parked on a hill.

•

Wear heavy gloves when handing the cables.

•

Use the PARKING BRAKE where appropriate.

•

Operate the winch ONLY FROM THE OPERATOR’S SEAT, never from outside the cab.

•

Do not winch at a sharp angle. This could cause your machine to tip over.

7. Keep all work surfaces and engine compartment clean and free of oil, grease, snow, ice and debris. Give special care to hand-holds, steps, pedals and floors.

•

Overloading can make a machine unstable and create a roll-over condition.

•

Keep load low and close to skidder for best stability.

8. Be constantly aware of the location of fellow workers. Especially those on foot.

•

A load of logs will change the handling and stability of the skidder.

9. Your Skidder is a one person machine. No riders inside or outside.

•

Always be prepared to dump the load in case of emergency.

5. Always wear and use your seat belt and other Personal Protective Equipment, such as: hard hat, safety shoes, safety glasses and heavy gloves.

6. Rain, snow, ice, loose gravel, soft ground, etc. will change the operating capabilities of your machine.

10. Be aware of what is happening around you.

Maintain a safe operating distance between your machine and other equipment and workers.

11. Know the hand signals that are being used on your job site.

12. Keep skid roads, secondary trails and landing areas clear of debris and in good condition.

2.110

Tigercat 610E/615E Skidder

Controls and operation

CORRECT KEEP LOAD LOW AND CLOSE TO SKIDDER FOR BEST STABILITY. BETTER WEIGHT DISTRIBUTION BETWEEN FRONT AND REAR OF MACHINE.

INCORRECT DECREASED STABILITY DUE TO LOAD POSITION. POORER WEIGHT DISTRIBUTION BETWEEN FRONT AND REAR OF MACHINE

EFFECT OF LOAD POSITION ON STABILITY AND WEIGHT DISTRIBUTION

2.111

Controls and operation

Tigercat 610E/615E Skidder

WARNING Backup carefully. If a log strikes an object, it could be pushed forward through the grapple and into the operator's cab.

When running empty, always keep grapple tongs closed to prevent striking the tires or the machine.

GRAPPLE SKIDDING 1. The timber may be pre-bunched or left for single pick-up. Depending on sizes you may have to single skid or bunch before skidding.

2. Logs should be picked up 3 ft. (1 meter) from the butt end.

3. If you have to add more logs or bunch, place the butt end of the new logs crosswise on top of the load in an “X” pattern. Place the Grapple over the logs where they cross and pick up the complete load.

4. The articulation feature in the Skidder increases the reach to the left and right and increases the range of pick-up for the grapple.

5. When pushing or backing up with a load, you must have the logs lined up with the Skidder and backup in a straight line, since you are using the butt pan to push the logs.

6. The articulation feature allows decking the logs from both sides of the pile.

7. Timber can be piled using the grapple or the dozer blade, depending on conditions.

8. The Dual Arch Skidder has the added ability to reach below ground level. This feature can be used to get the machine unstuck.

Do not drop the load as it helps to support the weight of the machine. Pull the load up close to the butt pan and lower the grapple downwards to solid ground. This process will push the back end of the Skidder upward and forward. Continue to repeat this process until the Skidder is on solid ground.

2.112

Tigercat 610E/615E Skidder

Controls and operation

CABLE SKIDDING: 1. Locate the skidder so that the winch cable will lay in a fairly straight line.

2. Lower the dozer and grapple to the ground to anchor the machine.

Grapple may have to be raised, depending on winching angle and land terrain.

3. Chokers should be attached close to the butt end of the log.

4. If skidding multiple logs, attach furthest log away, to end of main cable, with closer logs ahead of it.

5. Winch in a straight line to prevent tip over problems. Note that cab doors must be closed and parking brake disengaged to operate the winch in function.

6. Draw the logs in as close as possible to the butt pan and as high as stability will permit.

7. Raise the grapple to a safe height and raise the dozer to its full height.

8. If you encounter soft ground or steep hills it may be necessary to drop the load “on the move” and allow the winch to “free spool” without stopping the skidder. Once on solid ground or on top of the hill, stop the skidder, lower the dozer and winch the load back into the butt pan.

9. Adjust your speed to the terrain, ground conditions and the load your skidding.

2.113

Controls and operation CARE OF THE MACHINE

Tigercat 610E/615E Skidder CARE OF POLYCARBONATE WINDOWS IN CAB

1. Ensure that all fluid levels are always at the proper level. Use the preventative maintenance schedule in SECTION 3 of this manual .

Most windows used in the cab are made from a polycarbonate resin thermoplastic. This material is a replacement for glass when improved strength, durability and safety is required.

2. Follow proper procedure for cleaning windows described in this section.

Polycarbonate material is expected to resist heavy impact from large branches and falling tree tops and to absorb high levels of energy when contacted by high velocity thrown objects such as wood chips, disc saw blade teeth or broken harvester head saw chain.

3. Apply grease to all lubrication points at required intervals.

4. Do not apply load to a cold engine.

5. Close and secure all doors and access covers.

6. Do not allow branches, twigs, leaves or pine needles to build up around radiator intake doors or anywhere else on the machine.

Clean frequently but at least once daily.

Refer to CLEANING A/C CONDENSER AND COOLING ASSEMBLY in THIS SECTION. 7. Be sure that the grapple and dozer blade are resting on the ground before servicing or parking the machine.

IMPORTANT !

When cleaning the machine with pressurized water it is important to avoid getting water directly or indirectly into the exhaust tube. Water in the exhaust tube will damage sensors and SCR system components and affect the proper operation of the aftertreatment system and the engine.

The extreme operating environment seen in logging applications heightens the need to regularly inspect and properly maintain polycarbonate cab windows.

Polycarbonate windows are an essential piece of operator protective equipment and should be maintained as such. It is important to note that cracks, chips, notches or scarring anywhere on the viewing surface or edges of the window will decrease ability to resist heavy impacts and therefore compromise effectiveness as operator safety protective equipment. Windows with these defects must be replaced immediately.

Refer to the next section for detailed information regarding inspection and maintenance of polycarbonate windows.

2.114

Tigercat 610E/615E Skidder

Controls and operation

INSPECTION AND MAINTENANCE

RESISTANCE TO CHEMICALS

Daily inspection and maintenance is essential to confirm that the window’s ability to protect the operator has not been compromised.

The resistance of polycarbonate material to chemical exposure varies widely. Fortunately, polycarbonate materials have good resistance to diesel fuel, grease, hydraulic oil, kerosene and engine oil.

•

Inspect all windows daily and immediately after any impacts.

•

Check for any damage to the window material or steel structure in the area of the window mounting.

Other chemicals however can seriously weaken the polycarbonate.

•

The edges of the polycarbonate window must be evenly and fully supported on a flat surface around the entire window opening at all times.

Bent or dented skylight structures must be replaced immediately. Bent or dented cab structures must be evaluated immediately for possible repair or replacement.

•

The edges of the polycarbonate window must be free from cracks, chips, notches or scarring and must not be pinched or stressed. These defects will decrease ability to resist heavy impacts. Windows with these defects must be replaced immediately.

•

Cracks, chips, notches or scarring anywhere on the viewing surface of the window will decrease ability to resist heavy impacts.

Windows with these defects must be replaced immediately.

DO NOT permit any of the following chemicals to come into contact with polycarbonate windows: • • • • • • • • • • • • •

acetone air conditioning refrigerant ammonia anti-freeze benzene brake fluid carbon tetrachloride cutting oils gasoline lacquer thinner toluene turpentine xylene

RESISTANCE TO WATER

•

Bent, dented or missing window retaining parts must be replaced immediately.

•

Rubber materials used in mounting the window must be maintained in good condition.

•

Identification of the polycarbonate originally used by Tigercat is hot stamped in a corner of the window to identify its composition. Do not use any replacement window without proof of its material composition. Do not substitute with any other materials.

•

Skylights, cab structures, windows and window retaining parts must not be modified or replaced with components that are not approved by Tigercat.

Polycarbonate material has good resistance to water up to approximately 65°C (150°F). Above this temperature the effect of water is timetemperature related. This means that the higher the water temperature, the shorter the time before the polycarbonate is adversely affected.

Exposing polycarbonate to repeated steam cleanings or high temperature pressure washing may result in crazing, a phenomenon that causes clouding of the surface. Crazing can ultimately result in a loss of physical strength and may precede a fracture.

2.115

Controls and operation

Tigercat 610E/615E Skidder

CLEANING INSTRUCTIONS

CAUTIONS

The viewing surfaces of polycarbonate cab windows are specially treated with a hard coating to provide enhanced resistance to abrasion and ultra-violet (UV) radiation.

•

DO NOT use abusive cleaning procedures either by hand or pressure washing on polycarbonate windows.

•

DO NOT use brushes, razor blades, scrapers, squeegees or other sharp tools on polycarbonate windows.

•

DO NOT clean polycarbonate windows when the daytime temperature is high or in direct sunlight.

•

DO NOT use abrasive or highly alkaline cleaners on polycarbonate windows.

•

DO NOT use glass cleaners in either aerosol or non-aerosol containers to clean polycarbonate windows.

•

Failure to follow these cleaning instructions will shorten the service life of polycarbonate and may cause visual hazing, loss of light transmission and delamination of the polycarbonate hard surface coating.

The following instructions are provided to prolong the life of this protective hard coating.

1. Rinse the window thoroughly with lukewarm water 2. Using a soft cloth, cellulose sponge or chamois, gently wash the window with a mild solution of soap or detergent in lukewarm water. Do not scrub or use brushes or squeegees.

Brand name soaps and detergents recommended for cleaning polycarbonate are: • Fantastik • Formula 409 • Hexcel F.O. 554 • Joy • Lysol • Mr. Clean • Neleco-Placer • Pine-Sol • Top Job 3. Rinse the window thoroughly with lukewarm water.

4. Dry the window with a moist soft cloth, cellulose sponge or chamois to prevent water spotting.

5. To remove grease or oil, first rub lightly with a good grade of VM&P Naphtha or isopropyl alcohol followed by the same rinse, wash, rinse and dry procedure described in steps 1 to 4.

CONCEALING HAIRLINE SCRATCHES The appearance of scratches and minor abrasions on the surfaces of polycarbonate windows can be minimized by using a mild automotive polish such as: • • •

Johnson’s Paste Wax Novus Plastic Polish #1 and #2 Mirror Glaze Plastic Polish

Be certain to clean the polycarbonate window as outlined prior to application of an automotive polish. Refer to CLEANING INSTRUCTIONS.

Refer also to RESISTANCE TO CHEMICALS for a list of chemicals which should not be permitted to come into contact with polycarbonate windows.

2.116

Tigercat 610E/615E Skidder

Controls and operation

GRAFFITI REMOVAL •

•

For removal of paints, marking pen inks, etc., the use of Butyl Cellosolve is generally effective. The use of masking tape, adhesive tape or lint removal tools works well for lifting off old weathered paints.

WINDOW SCREEN HANDKNOB

To remove labels, stickers, etc., the use of kerosene, VM&P Naphtha, or petroleum spirits is generally effective. When the solvent will not penetrate sticker material, apply heat (hair dryer) to soften the adhesive and promote removal.

Refer also to RESISTANCE TO CHEMICALS for a list of chemicals which should not be permitted to come into contact with polycarbonate windows.

FIRE PRECAUTIONS Polycarbonate window material will ignite when exposed to an ignition source in excess of 427°C (800°F). When working around polycarbonate windows, observe similar fire precautions to those in place for wood.

SIDE WINDOW SCREEN SIDE WINDOW SCREENS 620E-031

The side window screens can be removed to clean the windows. Screens are provided for the personal protection of the operator and must be reinstalled immediately after cleaning the windows.

A handknob is provided on both the inside and the outside. By unscrewing either (not both) of these knobs, the screen will be free to swing out on the hinges. Be aware that the screen will swing outwards with considerable force, if the door is open.

All handles should be hand tight only at all times.

2.117

Controls and operation

Tigercat 610E/615E Skidder

CLEANING A/C CONDENSER AND COOLING ASSEMBLY The side by side A/C condenser, radiator, charge air cooler (CAC) and hydraulic oil cooler is mounted at the front of the machine. The engine fan draws air from the engine compartment, through the A/C condenser and cooling assembly and blows it out through the front door screen.

The screened access panels on each side of the engine compartment act as debris screens to prevent debris from being drawn into the engine compartment.

A/C CONDENSER

CHARGE AIR COOLER (CAC) HYDRAULIC OIL COOLER

RADIATOR

The A/C condenser and cooling assembly should be checked every 8 hours (every shift) for accumulation of twigs, leaves, pine needles and dust.

This cooling assembly must be checked daily for debris and may have to be thoroughly cleaned on a weekly or monthly basis, depending on operating conditions. Compressed air or water may be used for cleaning. Use compressed air for cleaning only when the machine is cold to avoid the risk of fire caused by debris contacting hot surfaces.

620E-059

CLEAN A/C CONDENSER AND COOLING ASSEMBLY

610E-024

CLEAN SCREENED ACCESS PANELS BOTH SIDES

Avoid the risk of fire caused by debris accumulating on surfaces that may become hot during machine operation. Always use care when cleaning to ensure that debris removed from one area of the machine does not accumulate on other areas of the machine. For more information on fire prevention refer to FIRE PREVENTION in SECTION 1 of THIS MANUAL. If an oil leak has occurred in this area it should be thoroughly power-washed with a mild soap to ensure that all of the oil is removed.

CAUTION Use compressed air for cleaning only when the machine is cold to avoid the risk of fire caused by debris contacting hot surfaces.

If using compressed air for cleaning, use at 30psi or less.

Always use personal protective equipment to guard against flying debris.

CAUTION Avoid the risk of fire caused by debris accumulating on surfaces that may become hot during machine operation. Always use care when cleaning to ensure that debris removed from one area of the machine does not accumulate on other areas of the machine.

2.118

Tigercat 610E/615E Skidder

Controls and operation

USING THE FAN CLEAN FUNCTION TO REMOVE DEBRIS DURING OPERATION (IF EQUIPPED-VARIABLE PITCH FAN OPTION) The Flexxaire® cooling fan has a CLEAN function for use in cleaning debris from the machines engine enclosure. The pitch of the fan blades is changed and the direction of airflow through the engine enclosure is reversed. This change in airflow blows debris from the machine's engine enclosure to eliminate potential overheating and poor machine performance caused by overheating. Ensure that there are no personnel standing directly to the sides of the machine when performing this operation, as dust and debris will fly out.

When the fan control switch is in the AUTOMATIC position, the system will automatically cycle through an auto clean cycle. The frequency and duration of the auto clean cycle is adjustable through the computer control system menu.

Refer to FAN CONTROL SWITCH in THIS SECTION for more information.

USING THE FAN CONTROL SWITCH IN THE EVENT OF AN ENGINE COOLANT TEMPERATURE AND/OR HYDRAULIC OIL TEMPERATURE ALARM. In the event of an engine temperature and/or hydraulic oil temperature alarm: 1. Stop the machine.

2. Place the fan control switch in the FULL ON position until cooling is achieved.

3. If necessary use the CLEAN function to reverse fan flow and clean debris from the machine's engine enclosure 4. In severe operating conditions manual cleaning of debris may be required.

5. If the problem persists check engine coolant and/or hydraulic oil levels. Refer to OPERATING MACHINE – PRESTART CHECKS in THIS SECTION. 6. Return the fan control switch to the AUTOMATIC position and check for proper operation of the fan. In the event of a problem with the automatic control system the fan control switch should be placed in the FULL ON position while the machine is operating until the fan control can be properly repaired.

2.119

Controls and operation ARTICULATION LOCK STRAIGHT LOCKED POSITION

Tigercat 610E/615E Skidder ARTICULATION LOCK ARTICULATED LOCKED POSITION

1. Position machine on level ground and steer machine into a straight ahead position.

1. Position machine on level ground and steer machine into a fully articulated position to the right.

2. Lower grapple and dozer blade to the ground, engage parking brake, stop engine and remove ignition key.

2. Lower grapple and dozer blade to the ground, engage parking brake, stop engine and remove ignition key.

ARTICULATION LOCK

ARTICULATION LOCK REAR CHASSIS

REAR CHASSIS

RETAINING PINS

620E-002

ARTICULATION LOCK STORED POSITION

RETAINING PINS

620E-002

ARTICULATION LOCK STORED POSITION

3. Remove both retaining pins from the articulation lock. Relocate articulation lock between front and rear chassis. Line up holes at each end of articulation lock with holes in chassis’ and secure in place with both retaining pins.

3. Remove both retaining pins from the articulation lock. Relocate articulation lock between front and rear chassis. Line up holes on the articulation lock with holes in chassis’ as shown and secure in place with both retaining pins.

4. After work is completed, relocate articulation lock into storage position on rear chassis and hold in place with retaining pins.

4. After work is completed, relocate articulation lock into storage position on rear chassis and hold in place with retaining pins.

630E-060

ARTICULATION LOCK IN STRAIGHT LOCKED POSITION

630E-073

2.120

ARTICULATION LOCK IN ARTICULATED LOCKED POSITION

Tigercat 610E/615E Skidder RETRIEVAL POINTS

Controls and operation These points are designed to accept a lifting chain shackle. Warning: Use shackles and chains that are appropriately sized for the load to be retrieved.

Retrieval of the machine may be required, in the event that a machine becomes immobile due to terrain conditions that do not permit it to escape under its own power.

3. REAR RETRIEVAL POINTS If the machine becomes immobile with its rear oriented towards the aiding machine, there are retrieval points located at the rear chassis on each end of the rear axle. These points are labeled 'I' and 'J' on the machine lifting/tiedown label.

Refer also to TOWING INSTRUCTIONS in THIS SECTION, in the event that the engine or drive system are not functioning well enough to allow the machine to move in tandem with the aiding machine.

1. There are retrieval points located on both the front and rear of the machine to aid in its retrieval.

These points must be used together in a retrieval situation.

These points are designed to accept a lifting chain/hook in either a basket or choker hitch configuration. Warning: Use chains that are appropriately sized for the load to be retrieved.

These points must be used together in a retrieval situation.

2. FRONT RETRIEVAL POINTS If the machine becomes immobile with its front oriented towards the aiding machine, there are two retrieval points located at the front of the front chassis in front of the heat exchanger.

These points are labeled 'G' and 'H' on the machine lifting/tie-down label.

These points must be used together in a retrieval situation.

E

B

4. Once the immobile machine has been connected to the aiding machine, both machines can move in tandem to free the immobile machine.

AF

J

H G

I

E

A B C D E

C I,J

DF

F

G,H

G H I

E

J

A,D F

B,C

43398BUNI R0

E

B1

B2

AF

J

H G

I

E

C1

C2

DF

I,J

G,H

A B C D E F G H I J

E B1,C1

A,D F

B2,C2

43510BUNI R0

2.121

Controls and operation TRANSPORTING INSTRUCTIONS

Tigercat 610E/615E Skidder CAUTION

The skidder may be transported with the wheels on or off.

As a fire prevention measure, AFTER transporting (trucking) a machine from one job sight to the next, open all doors and access panels and blow off any debris that could have re-positioned itself onto the engine and exhaust parts due to wind turbulance caused by the journey. Refer also to FIRE PREVENTION in SECTION 1 of THIS MANUAL.

With wheels on:•

DO NOT remove air from tires, this will result in damage to the tires!

With wheels off:•

If the wheels are removed the machine must be blocked so that the centre joint is one inch or more above the truck bed.

With the wheels on or off:•

The dozer blade must be down on the truck bed.

•

The grapple must be closed and lowered to the truck bed.

630E-060

ARTICULATION LOCK IN STRAIGHT LOCKED POSITION

•

The articulation lock bar must be installed so that the machine is oriented in the straight locked position.

•

The machine must be cross chained (side to side) at both the front and rear axle area.

E

B

•

Chains must be attached to the grapple to prevent movement.

•

Additional chains may be installed on the two tow lugs (front of unit) and on the bottom cab access steps.

IMPORTANT !

When transporting the machine, chains must be used to prevent forward, reverse and side to side movement of the machine.

Do not secure the machine to the truck ANYWHERE near the centre joint area as this can seriously damage the centre joint.

Use only transport regulation chains for this purpose, example; 5/16" grade 7 with a tensile strength of 43500 kg (96,000lb)/chain. Using inferior or damaged chains could cause the load to shift.

AF

J

H G

I

E

C I,J

A B C D E

DF

F

G,H

G H I

E

B,C

A,D F

J 43398BUNI R0

2.122

Tigercat 610E/615E Skidder

Controls and operation

TIE DOWN POINTS 1. When a skidder is to be transported on a flat bed the articulation lock bar must be installed so that the machine is oriented in the straight locked position.

2. Chains must be used to prevent forward, reverse and side to side movement of the machine. Tie-down locations are provided on the machine for this purpose. All tie-down points must be used to ensure no movement of the machine, or it’s associated parts, occur during transport.

3. The front axle of the machine must be cross chained from side to side. The front axle tie-down points are labeled 'A' and 'D' on the machine lifting/tie-down label.

The chain should be wrapped around each end of the axle housing, without overlapping, and chained at a 45° angle in the forward, reverse and side to side directions.

E

B1

4. In the case of a 4 wheeled machine, the rear axle of the machine must be cross chained from side to side of the flat bed. The rear axle tie-down points are labeled 'B' and 'C' on the machine lifting/tie-down label.

The chain should be wrapped around each end of the axle housing, without overlapping, and chained at 45° angle in the forward, reverse and side to side directions.

5. The grapple is to be stored in a position with grapple tongs closed and supported by the flat bed platform. The grapple tie-down points are labelled 'E' on the machine lifting/tie-down label.

A strap or chain is to be tightened across the top of the grapple box to prevent grapple movement.

6. The dozer blade is to be stored in a position with its blade tip supported by the flat bed platform. The dozer blade tie-down points are

B2

AF

J

H G

I

E

C1

C2

DF

I,J

G,H

A B C D E F G H I J

E B1,C1

A,D F

B2,C2

43510BUNI R0

2.123

Controls and operation

Tigercat 610E/615E Skidder

labelled 'F' on the machine lifting/tie-down label.

A strap or chain is to be tightened across the top of the dozer blade arms to prevent movement.

3. Additionally there are lifting points located at the rear chassis on each end of the rear axle.

These points are labeled 'I' and 'J' on the machine lifting/tie-down label.

These points are designed to accept a lifting chain/hook in either a basket or choker hitch configuration.

LIFTING POINTS Lifting of the machine should be done for transportation purposes only.

4. All lifting points must be used during a lifting operation.

WARNING Use shackles and chains that are appropriately sized for the load to be lifted.

5. Position the hoist above the centre of gravity to ensure machine stability & leveling.

1. The articulation lock bar must be installed so that the machine is oriented in the straight locked position.

2. There are two lifting points located at the front of the front chassis in front of the heat exchanger. These points are labeled 'G' and 'H' on the machine lifting/tie-down label.

These points are designed to accept a lifting chain shackle.

E

B

AF

J

H G

I

E

A B C D E

C I,J

DF

F

G,H

G H I

E

J

A,D F

B,C

43398BUNI R0

E

B1

B2

AF

J

H G

I

E

C1

C2

DF

I,J

G,H

A B C D E F G H I J

E B1,C1

A,D F

B2,C2

43510BUNI R0

2.124

Tigercat 610E/615E Skidder TOWING INSTRUCTIONS

Controls and operation

(IF EQUIPPED WITH EHS TRANSMISSION) A malfunction of the machines equipment may make towing necessary.

Towing is only recommended over short distances.

It is always better to make repairs at the point where the machine is parked whenever possible.

Prior to towing, be sure that the machine is either on level ground, or is secured by the tow vehicle to prevent the machine from rolling unexpectedly.

IMPORTANT! Before towing, the transmission must always be disconnected from the drive wheels.

615C-025

FRONT DRIVE SHAFT

615C-024

MID DRIVE SHAFT

615C-023

MID DRIVE SHAFT

Never tow a machine in gear. If the machine is subjected to hard pulling while in gear, the extremely high forces created will cause significant damage to the components of the hydrostatic drive system and the transmission Never tow the machine at over 2 mph.

1. To facilitate towing, the drive shafts must be disconnected from the transmission.

2. Disconnect the front drive shaft at the front axle.

3. Remove the mid drive shaft.

4. Raise the grapple and dozer blade off the ground and turn off the engine.

5. To allow the machine to steer while towing and prevent damage to the steering cylinders, cross hydraulic hoses on one of the steering cylinders. This will allow trapped oil to flow freely between the two steering cylinders, providing ease of turning with some dampening effect.

6. The machine will be towed from the front, making use of the towing lugs at front of machine behind the dozer blade.

Ensure a vehicle of equal power and size is used for towing.

STEERING CYLINDERS

STEERING CYLINDERS

When going downhill, be sure to use a holdback vehicle as the machine is now without any effective braking.

7. When towing is completed, reinstall the mid drive shaft, reconnect the front driveshaft and reconnect the steering cylinder hoses in their proper locations.

SM47

2.125

NORMAL HOSE CONNECTIONS

HOSES ON ONE CYLINDER CROSS CONNECTED FOR TOWING

Controls and operation

Tigercat 610E/615E Skidder

2.126

Tigercat 610E/615E Skidder SECTION 3 - LUBRICATION & MAINTENANCE CONTENTS - SECTION 3

ISSUE 2.0 MARCH 2015

AFTERTREATMENT SYSTEM................................................................................................................ 3.40 AIR CLEANER MAINTENANCE.............................................................................................................. 3.37 AIR CONDITIONING SYSTEM, CHECKING........................................................................................... 3.56 APPROVED ANTI-SEIZE PASTES FOR EXHAUST / AFTERTREATMENT LINE (TIGERCAT BY FPT TIER 4F ENGINES)................................................................................................ 3.48 APPROVED HYDRAULIC OILS.............................................................................................................. 3.15 ARTICULATION LOCK............................................................................................................................. 3.51 AXLE AXLE LEVEL CHECK, FILL AND DRAIN LOCATIONS....................................................................... 3.66 AXLE PINION SEAL GREASE FITTING...................................................................................... 3.6, 3.66 LIMITED SLIP ADDITIVES................................................................................................................... 3.66 REAR (BOGIE) AXLE DRAINING AND REFILLING BOGIE AXLE...................................................................................... 3.68 SLEW BEARING LUBRICATION - BOGIE AXLES........................................................................... 3.69 CAB SAFETY CABLE.............................................................................................................................. 3.59 CAB SUPPORT BRACE.......................................................................................................................... 3.59 CENTRE JOINT LUBRICATION...................................................................................................................................... 3.50 MAINTENANCE.................................................................................................................................... 3.50 DENOX 2.2 SYSTEM............................................................................................................................... 3.40 DEPRESSURIZING SUSPENDED MACHINE ELEMENTS.................................................................... 3.36 DIESEL EXHAUST FLUID (DEF) HANDLING......................................................................................... 3.49 DIESEL OXIDATION CATALYST/SELECTIVE CATALYTIC REDUCTION AFTERTREATMENT SYSTEM (DENOX 2.2 SYSTEM).......................................................................... 3.40 DRAINING ENGINE COOLANT............................................................................................................... 3.31 DRAINING HYDRAULIC TANK................................................................................................................ 3.29 DRAINING THE DIESEL EXHAUST FLUID TANK.................................................................................. 3.26 DRAINING THE FUEL TANK................................................................................................................... 3.22 DRAINING TRANSMISSION OIL............................................................................................................. 3.32 EMERGENCY EXITS, CHECK MONTHLY................................................................................................ 3.8 FILLING HYDRAULIC TANK.................................................................................................................... 3.30 FILTERS CHARGE PRESSURE FILTER............................................................................................................. 3.28 DEF SUPPLY MODULE FILTER.......................................................................................................... 3.24 EHS TRANSMISSION FILTER............................................................................................................. 3.29 FUEL FILTER/WATER SEPARATOR.................................................................................................... 3.20 FUEL TANK STRAINER....................................................................................................................... 3.20 HYDRAULIC OIL DOUBLE FILTERS................................................................................................... 3.27 SERVICING GUIDELINES FOR OIL FILTERS..................................................................................... 3.27 FIRE PREVENTION................................................................................................................................... 3.9 FRONT AXLE AXLE PINION SEAL GREASE FITTING.............................................................................................. 3.67 GENERAL MAINTENANCE....................................................................................................................... 3.8 GRAPPLE SNUBBER MAINTENANCE................................................................................................... 3.52 HOUR METER – MAINTENANCE............................................................................................................. 3.3 LUBRICATION AND SERVICE POINTS MACHINES 6101101 TO 6102500....................................................................................................... 3.16 MACHINES 6151001 TO 6151500....................................................................................................... 3.18

Lubrication and Maintenance

Tigercat 610E/615E Skidder

NEW MACHINE MAINTENANCE.............................................................................................................. 3.3 FIRST 125 HOUR INSPECTION AND SERVICE REPORT................................................................... 3.3 INITIAL PREDELIVERY INSPECTION................................................................................................... 3.3 OIL ANALYSIS PROGRAM....................................................................................................................... 3.4 OIL LOST FROM LEAKAGE...................................................................................................................... 3.8 OIL SAMPLE COLLECTION PROCEDURES............................................................................................ 3.5 PARKING BRAKE MANUAL RELEASE OF PARKING BRAKE......................................................................................... 3.33 PARKING BRAKE ADJUSTMENT........................................................................................................ 3.33 PRESSURIZED WATER SYSTEM MAINTENANCE............................................................................... 3.54 SCHEDULED MAINTENANCE 8 HOURS..............................................................................................................................................3.10 48 HOURS............................................................................................................................................3.10 125 HOURS.......................................................................................................................................... 3.11 250 HOURS.......................................................................................................................................... 3.11 500 HOURS.......................................................................................................................................... 3.12 1000 HOURS........................................................................................................................................3.12 1500 HOURS........................................................................................................................................3.13 2000 HOURS........................................................................................................................................3.13 2 YEARS...............................................................................................................................................3.13 SEASONAL...........................................................................................................................................3.14 SERVICE AND LUBRICATION POINTS MACHINES 6101101 TO 6102500....................................................................................................... 3.16 MACHINES 6151001 TO 6151500....................................................................................................... 3.18 SERVICE BRAKE CHECKING BRAKE AND ACCUMULATOR FOR PROPER OPERATION.......................................... 3.35 START-UP PROCEDURE AFTER MAJOR MAINTENANCE................................................................... 3.64 TILTING THE CAB................................................................................................................................... 3.58 TIRE PRESSURES.................................................................................................................................. 3.76 TORQUE, FLUID CONNECTIONS.......................................................................................................... 3.72 TORQUE SPECIFICATIONS - GENERAL............................................................................................... 3.71 WEIGHTS OF COMMERCIAL WOOD..................................................................................................... 3.75 WHEELS, INSTALLING.............................................................................................................................. 3.3 WINCH MAINTENANCE - ALLIED WINCH.............................................................................................. 3.60 WINCH MAINTENANCE - CARCO.......................................................................................................... 3.62

3.2

Tigercat 610E/615E Skidder

Lubrication and Maintenance

PREVENTIVE MAINTENANCE SCHEDULE FOR 610E/615E Skidder NEW MACHINE MAINTENANCE *INITIAL PREDELIVERY INSPECTION:PERFORM THE INITIAL PREDELIVERY INSPECTION USING Tigercat FORM NUMBER 5339; "PDI AND 125 HOUR INSPECTION REPORT"

*FIRST 125 HOUR INSPECTION AND SERVICE REPORT:WITH THE OWNER'S MECHANIC PRESENT, PERFORM AN INSPECTION AND SERVICE ACCORDING TO THE Tigercat FORM NUMBER 5339; "PDI AND 125 HOUR INSPECTION REPORT" THIS MUST BE COMPLETED WITHIN THE FIRST 125 HOUR TIME FRAME. *IMPORTANT: TO QUALIFY FOR CONTINUED WARRANTY, THIS REPORT MUST BE COMPLETED AND RETURNED TO Tigercat Industries Inc. WARRANTY DEPARTMENT.

IMPORTANT!

TIGHTENING POINTS FOR:THE FIRST 125 HOUR INSPECTION REPORT:

WHEELS:

When installing wheels, ensure that all paint has been removed from the mating surfaces of both the wheel disc and the flange of the axle to ensure metal to metal contact.

All hydraulic connections Hose clamps Centre joint pin securing bolts Transmission securing bolts Engine mounting bolts Axle mounting bolts Wheel retaining bolts Cab securing bolts Pin retainers Any other loose nut, bolt or fitting

For more complete instructions also refer to section 8 of the service manual.

HOUR METER – MAINTENANCE: Check the hour meter on a regular basis to determine your scheduled maintenance times.

The intervals and times on the scheduled maintenance chart in this manual are for normal operating conditions.

NOTE: Use of filters other than genuine Tigercat replacement filters is not recommended.

If your machine is being operated in difficult or severe conditions, you should service your machine at shorter intervals.

Refer to diesel engine service manual and attachment manual for additional required maintenance at this scheduled time period.

3.3

Lubrication and Maintenance

Tigercat 610E/615E Skidder

TIGERCAT OIL ANALYSIS PROGRAM Effective for all 2007 model year 600'E' series skidders sold in North America, oil sampling and analysis must be performed during the warranty period as per the schedule below.

Warranty coverage of powertrain components, specifically hydrostatic pumps and motors, auxiliary pumps, axles, transfer case and driveshafts is contingent on performance of regular oil sampling at the owner’s expense during the warranty period.

Location Hydraulic Oil Transmission Axles – Front & Rear

610E 615E Model

First Sample Follow-up Samples 125 Hours Every 1000 Hours or 6 Months 125 Hours Every Oil Change (500 Hours or 3 Months) 125 Hours Every Oil Change (1000 Hours or 6 Months)

FIRST SAMPLE There will be no charge for the first oil samples required to be taken during the 125-Hour Inspection Service that will be scheduled and performed by your Tigercat dealer. Refer to NEW MACHINE MAINTENANCE in THIS SECTION. FOLLOW-UP SAMPLES All follow-up samples must be taken as indicated in the chart above and will be the responsibility of the machine owner.

Copies of all oil analysis results must be forwarded to the Tigercat Warranty Department for continued warranty coverage. If samples are taken using the Tigercat Oil Analysis Program, a copy of all results will automatically be sent to Tigercat.

Tigercat Oil Analysis Kits are available from your Tigercat dealer parts department. If required, arrangements can also be made with your Tigercat dealer to supply and perform all of the required followup oil samples.

Refer also to OIL SAMPLE COLLECTION PROCEDURES in THIS SECTION for sample valve and drain plug locations.

TIGERCAT OIL ANALYSIS KITS Each kit includes a Pre-paid Sample Bottle and Sample Information Form. Pre-printed mailing labels are also included to ensure all samples are quickly returned directly to the lab for immediate analysis and results within 24 hours of receipt.

The same type of sample bottle can be used for all types of oil testing including: Hydraulic Circuits, Final Drives, Axles, Gearboxes, Engines, etc.

To ensure accurate and meaningful results are obtained, each kit also includes detailed instructions on how properly collect, prepare and ship the oil samples.

Contact your Tigercat Dealer Parts Department to order Kits.

3.4

Tigercat 610E/615E Skidder

Lubrication and Maintenance

TIGERCAT OIL ANALYSIS PROGRAM OIL SAMPLE COLLECTION PROCEDURES HYDRAULIC SAMPLE VALVE

Fill out the Sample Information Form (SIF) completely and accurately. When taking multiple oil samples, fill out all of the required SIF forms in their entirety, prior to taking any oil samples. Then, immediately package each completed SIF form together with the matching oil sample in the black outer shipping container as each individual sample is taken. This will reduce the possibility of mixing up or incorrectly identifying the SIF forms and oil samples. Incorrectly identified samples could result in a false warning alarm.

The accuracy of the lab analysis results is very dependent on the quality of the oil sample taken. Collection of clean oil samples that are representative of the main body of oil are essential if meaningful lab results are to be obtained.

Erroneous readings may result if proper collection, handling, packaging and shipping practices are not followed prior to the sample being tested by the lab. To be able to accurately compare and trend the lab results over time, all follow-up samples should be consistently taken from the same location using the same techniques as all previous samples.

•

Ensure that all sample valves and drain plugs are clean and free of debris.

•

Remove the sample bottle cap only when ready to take the sample. Keep the cap clean – do not put it in your pocket or let it get contaminated in any way.

•

Do not allow any airborne dirt, etc. to enter the sample bottle.

•

Avoid contamination of the sample – replace the sample bottle cap immediately after filling the bottle to approximately ¾ full.

620E-052

MAIN HYDRAULIC OIL

Hydraulic Oil Samples: •

Hydraulic oil samples should be taken from the circulating oil flow at operating temperature, with no functions actuated, using sample valves that are permanently located on the machine whenever possible.

•

To obtain a representative oil sample, sample valves must be purged before the actual oil sample is taken. Drain a minimum of 3 or 4 ounces of oil into a separate container and discard this oil using approved recycling methods.

•

Replace the dust cover on the sample valve immediately after taking the oil sample and sealing the sample bottle.

All samples taken should be immediately forwarded to the lab for processing.

Contact your Tigercat dealer to purchase additional or replacement hydraulic sample valves or drain plugs.

In cases where oil samples must be pumped or otherwise drawn out of a reservoir or housing, a hand operated oil suction pump is also available from your Tigercat dealer.

3.5

Lubrication and Maintenance

Tigercat 610E/615E Skidder

TIGERCAT OIL ANALYSIS PROGRAM Transmission and Axle Oil Samples: •

These samples can be taken during the oil change process.

•

To obtain a representative oil sample, ensure the oil is warm and has not settled very long (within 30 minutes of shutdown).

•

Place the required drain container under the machine to capture the used oil to be discarded using approved recycling methods.

•

Remove the drain plug and allow approximately 50% of the oil to drain, then place the sample bottle in the stream of draining oil to obtain a representative sample.

AXLE LEVEL CHECK AND FILL

SAMPLE LOCATION / TRANSMISSION DRAIN 630C-100

PINION SEAL GREASE FITTING

TRANSMISSION OIL

AXLE LEVEL CHECK AND FILL (FAR SIDE)

AXLE DRAIN 4658D02

STANDARD DUTY AXLE DRAIN AND FILL LOCATIONS (FRONT AXLE SHOWN 610E)

PINION SEAL GREASE FITTING

AXLE LEVEL CHECK AND FILL (FAR SIDE)

AXLE LEVEL CHECK AND FILL

AXLE DRAIN 4326D03

STANDARD DUTY AXLE DRAIN AND FILL LOCATIONS (REAR AXLE SHOWN 610E) 3.6

Tigercat 610E/615E Skidder

Lubrication and Maintenance

TIGERCAT OIL ANALYSIS PROGRAM PINION SEAL GREASE FITTING

AXLE LEVEL CHECK AND FILL

AXLE LEVEL CHECK AND FILL (FAR SIDE)

AXLE DRAIN 4326D

STANDARD DUTY AXLE DRAIN AND FILL LOCATIONS (FRONT AXLE 615E)

AXLE LEVEL CHECK AND FILL (FAR SIDE)

BRAKE INSPECTION PORT (FAR SIDE)

BRAKE INSPECTION PORT

AXLE LEVEL CHECK AND FILL

PINION SEAL GREASE FITTING

AXLE DRAIN 4521D15

SEVERE DUTY AXLE DRAIN AND FILL LOCATIONS (FRONT AXLE 615E) BRAKE INSPECTION PORT (2 PLACES)

BOGIE HOUSING DRAIN PLUG (4 PLACES ) 52746B

BOGIE HOUSINGS FILL/LEVEL PLUG (2 PLACES)

DIFFERENTIAL DRAIN PLUG (1 PLACE) BOTTOM OF DIFFERENTIAL NOT VISIBLE IN THIS ILLUSTRATION

BOGIE AXLE FILL, DRAIN AND LEVEL PLUGS (STANDARD DUTY AXLE SHOWN) 3.7

Lubrication and Maintenance

Tigercat 610E/615E Skidder

GENERAL Inspect the EXHAUST SYSTEM DAILY for any signs of LEAKAGE. Check for worn, cracked, broken, or damaged pipes or muffler.

Also check for missing or damaged bolts or clamps. Should any exhaust leaks or defective parts be found, repairs must be made immediately. Engine exhaust leaks can cause fires, DO NOT OPERATE the machine until the exhaust leak is repaired.

CAUTION All handles, steps and platforms must be kept free of grease, oil, fuel, mud, snow and ice.

Clean around fill caps before checking or adding fluids Release hydraulic pressures and clean around hydraulic fittings before breaking connection.

Plug or cap immediately

During daily operation of the machine, the occurrence of exhaust leaks are usually accompanied by a change or increase in engine exhaust noise levels. These audible warnings cannot be ignored. Should any exhaust leaks occur during operation, the machine must be shut down immediately and not put back to work until the necessary repairs have been completed.

Clean up spills as soon as possible Always use clean oil and containers Drain dirty oil while still warm Do not exceed recommended fluid levels Service all hydraulic filters after the failure of a pump, motor, cylinder or valve. Failures of this nature could contaminate the entire hydraulic system

Always have a fire extinguisher at hand

Top up diesel fuel AT END OF Each shift to reduce contamination by condensation

For safety; when leaving the cab or leaving machine unattended or during service, always lower grapple and dozer blade to the ground

Clean up oil spills on walking surfaces and top of engine enclosure immediately

For safety, always block or support grapple and dozer blade when working under them.

Before welding on machine be sure to disconnect all electrical connections and follow all servicing safety precautions as outlined in WELDING, PRIOR TO in SECTION 1 of THIS MANUAL.

CHECK EMERGENCY EXITS MONTHLY: Alternate exit routes are provided: the sliding windows in the cab doors. These are only to be used if the cab doors cannot be opened.

When welding secure ground connection as close to working position as possible to prevent arcing across machined surfaces or through bearings

It is therefore essential that these emergency exits be checked at least once per month to ensure they are fully operational.

Clean away all branches, bark and chips.

Clean up all traces of oil to avoid fires

*OIL LOST FROM LEAKAGE

PER LEAKAGE RATE DAY ONE DROP IN 10 SECONDS 0.424 ONE DROP IN 5 SECONDS 0.852 ONE DROP PER SECOND 4.26 THREE DROP PER SECOND 14.2 DROPS BREAK INTO STREAM 90.83

LOST 0IL (LITERS) LOST 0IL (GALLONS) PER PER PER PER PER MONTH YEAR DAY MONTH YEAR 12.72 152.0 0.112 3.36 40.0 25.6 306.6 0.225 6.75 81.0 127.76 1533.1 1.125 33.75 405.0 425.86 5110.31 3.75 112.5 1350.0 2725.5 32706.0 24.00 720.0 8640.0

3.8

Tigercat 610E/615E Skidder

Lubrication and Maintenance

GENERAL FIRE PREVENTION Maintaining your machine properly will greatly extend its life and reduce your operating costs.

Fire can result in a machine loss which can be financially devastating.

1. Pine needles and bark when allowed to accumulate, form a fuel source that when ignited is extremely difficult to extinguish. A thorough program of regular cleaning and washing will reduce the possibility of a fire starting. In the event a fire does start, the regular cleaning program will improve the chances of successfully extinguishing a fire.

2. Pay close attention to wiring and plumbing routings during maintenance, ensure that ALL wiring harnesses or hydraulic hoses are properly restrained and clamped to prevent damage from chaffing.

3. Read the fire suppression system manual and have the system serviced regularly by qualified personnel.

4. In case of fire lower the boom system to the ground and turn off the engine before discharging the fire suppression system.

Also refer to the SAFETY section of this manual for additional information on how to prevent fires from starting on the machine.

3.9

Lubrication and Maintenance

Tigercat 610E/615E Skidder

SCHEDULED MAINTENANCE FREQUENTLY:

Clean: • Potentially damaging limbs or sticks from machine

• Check engine cooling air intake screens for possible restriction.

• A/C condenser, oil cooler, radiator refer to CLEANING A/C CONDENSER AND COOLING ASSEMBLY in SECTION 2 of the OPERATOR'S MANUAL.

EVERY 8 HOURS (EVERY SHIFT): • Perform "frequently" maintenance check, and in addition: • Check engine coolant level

Check: • Service brake for proper operation. Refer to SERVICE BRAKE – CHECKING BRAKE AND ACCUMULATOR FOR PROPER OPERATION in THIS SECTION. • All engine air intake system components (including charge air cooler) rubber elbows, connector hoses, tubes and clamps for damage, hardening, wear, cracks, leaks, loose clamps or loose hanger bracket hardware and repair immediately.

• Check engine oil level • Drain secondary fuel filter/water separator • Check air intake precleaner, clean as required • Check air cleaner unloader valve • Check air intake filter restriction indicator.

Replace primary filter if indicator is in red zone.

Replace secondary (safety) filter every third primary filter change to guarantee maximum performance and reliability.

• Charge Air Cooler for damage, wear, cracks, or leaks and repair immediately.

• For leakage around hydraulic components and flexible hoses. See "Oil lost from leakage" chart.

• Check hydraulic oil level with grapple head fully open, grapple head and dozer blade on the ground.

• For loose nuts, bolts and fittings

• Check winch sump oil level

• Condition and tension of fan belts.

• Check transmission oil level with dipstick

• Exhaust system for leaks.

• Lubricate front axle pivot, 2-fittings, purge

• Water pressure (60 psi [4 bar]) for pressurized water system (if equipped).

• Lubricate mid drive shaft 1-fitting, purge Note: Lubrication of mid drive shaft slip joint should be done with machine fully articulated and locked. Refer also to ARTICULATION LOCK – ARTICULATED LOCKED POSITION in THIS SECTION. • On 610E machines lubricate rear drive shaft bearing, 1-fitting, purge • On 615E machines lubricate rear drive shaft bearings, 2-fittings, purge • Lubricate centre joint bearings, 2-fittings, purge • Lubricate steering cylinder ends, 4-fittings, purge

If the water system has been operated, refer to PRESSURIZED WATER SYSTEM MAINTENANCE in THIS SECTION for refilling and charging instructions.

• Conduct an overall visual inspection.

Refer to diesel engine service manual and attachment manual for additional required maintenance at this scheduled time period.

EVERY 48 HOURS • Check the centre joint for looseness. Refer to CENTRE JOINT MAINTENANCE in THIS SECTION for instructions. If a problem is found corrective action should be taken immediately. Refer also to CENTRE JOINT in SECTION 11 of the SERVICE MANUAL for more detailed checking and adjustment procedures.

• Lubricate arch cylinders and pivots, 6 or 12-fittings, purge • Lubricate dozer blade cylinders and pivots, 6-fittings, purge • Lubricate grapple snubbers, 2-fittings, purge • Lubricate grapple, 8-fittings, purge • Lubricate grapple yoke, 8-fittings, purge 3.10

Tigercat 610E/615E Skidder

Lubrication and Maintenance

SCHEDULED MAINTENANCE EVERY 125 HOURS:

EVERY 250 HOURS:

• Perform "frequently" maintenance

• Perform "frequently" maintenance

• Perform 8 hour maintenance

• Perform 8 hour maintenance

And in addition: • Lubricate grapple rotator shaft, 2-fittings, 5-shots • Carry out A/C system inspection; Refer to AIR CONDITIONING SYSTEM, CHECKING in THIS SECTION

• Perform 125 hour maintenance And in addition: • Replace engine oil and filter.

• Lubricate grapple pinion gear spline, 1-fitting, 5-shots, (Note: remove pipeplug to access) • On 615E machines lubricate bogie axle slewing rings, 12-fittings; 2-places .

Check: • Check oil level in front and rear axles. Refer to AXLE – AXLE LEVEL CHECK, FILL AND DRAIN LOCATIONS and AXLE – REAR (BOGIE) AXLE (IF APPLICABLE) in THIS SECTION.

• Clean and thoroughly inspect all surfaces of the arch and boom for cracks. All cracks must be properly repaired in their early stages.

Note that in most cases cracks will continue to grow in size and often lead to major structural damage. Failure to regularly inspect for cracks and immediately repair the boom system will void the structural warranty.

Contact your Tigercat dealer for specific procedures required to correctly repair any cracks found.

• Fluid level in batteries unless maintenance free • Engine rpm.

• All hydraulic pressures • Hydraulic pump and motor securing bolts • Check fuel strainer (fuel tank filler screen)

• Refer to diesel engine service manual and attachment manual for additional required maintenance at this scheduled time period.

• Torque tightening points as per new machine maintenance • Proper operation of pressurized water system (if equipped). Refer to PRESSURIZED WATER SYSTEM MAINTENANCE in THIS SECTION.

Continued on next page

Visually check for damage to:• Arch and pivot linkage • Front and rear frame • Centre joint area • Attachment Make repairs immediately Visually inspect for:• Frayed electrical wiring and hydraulic hose • Wear in any other components • Refer to diesel engine service manual and attachment manual for additional required maintenance at this scheduled time period.

† Use of filters other than genuine Tigercat replacement filters is not recommended.

3.11

Lubrication and Maintenance

Tigercat 610E/615E Skidder

SCHEDULED MAINTENANCE EVERY 500 HOURS:

EVERY 1000 HOURS:

• Perform "frequently" maintenance

• Perform "frequently" maintenance

• Perform 8 hour maintenance

• Perform 8 hour maintenance

• Perform 125 hour maintenance

• Perform 125 hour maintenance

• Perform 250 hour maintenance

• Perform 250 hour maintenance

And in addition : • Replace primary fuel filter and secondary fuel filter/water separator • Replace hydraulic oil double element filters (2 elements) † 1 white, high performance element.

1 blue, water absorbing element.

• Replace charge pressure filter † • Replace EHS transmission filter † • Replace oil in transmission. Sample transmission oil for testing. NOTE: Warranty coverage of powertrain components is contingent on performance of regular oil sampling at the owner’s expense during the warranty period. Refer to OIL ANALYSIS PROGRAM in THIS SECTION for details.

• Lubricate front drive shaft 1-fitting, purge • Check for proper adjustment of the parking brake. Refer to PARKING BRAKE – PARKING BRAKE ADJUSTMENT in THIS SECTION. Refer also to PARKING BRAKE in SECTION 9 of the SERVICE MANUAL. • Lubricate door hinges, 8-fittings, purge • Refer to diesel engine service manual and attachment manual for additional required maintenance at this scheduled time period.

• Perform 500 hour maintenance And in addition: • Replace air cleaner unloader valve • Check centre joint preload with a dial indicator.

Refer to CENTRE JOINT – CHECKING CENTRE JOINT PRELOAD in SECTION 11 of the SERVICE MANUAL. If a problem is found corrective action should be taken immediately, refer to CENTRE JOINT PRELOAD ADJUSTMENT in SECTION 11 of the SERVICE MANUAL. • Replace oil in winch sump.

• For 610E machines drain and refill front and rear axles. Refer to LUBRICATION AND SERVICE CHART in THIS SECTION for recommended gear oils. Refer also to AXLE – AXLE LEVEL CHECK, FILL AND DRAIN LOCATIONS in THIS SECTION.Sample front and rear axle oil for testing. NOTE: Warranty coverage of powertrain components is contingent on performance of regular oil sampling at the owner’s expense during the warranty period. Refer to OIL ANALYSIS PROGRAM in THIS SECTION for details.

• For 615E machines drain and refill front axle and bogie axle differential, housings and planetary drives. Refer to AXLE – AXLE LEVEL CHECK, FILL AND DRAIN LOCATIONS and AXLE – REAR (BOGIE) AXLE (IF APPLICABLE) in THIS SECTION. Refer also to LUBRICATION AND SERVICE CHART in THIS SECTION for recommended gear oils. Sample bogie axle oil for testing.

NOTE: Warranty coverage of powertrain components is contingent on performance of regular oil sampling at the owner’s expense during the warranty period. Refer to OIL ANALYSIS PROGRAM in THIS SECTION for details.

• Sample hydraulic oil from the main hydraulic tank for testing. NOTE: Warranty coverage of powertrain components is contingent on performance of regular oil sampling at the owner’s expense during the warranty period.

† Use of filters other than genuine Tigercat replacement filters is not recommended.

3.12

Tigercat 610E/615E Skidder

Lubrication and Maintenance

SCHEDULED MAINTENANCE

•

• • •

Refer to OIL ANALYSIS PROGRAM in THIS SECTION for details.

Drain and refill pressurized water system (if equipped). Refer to PRESSURIZED WATER SYSTEM MAINTENANCE in THIS SECTION. Lubricate front axle pinion grease seal.

Lubricate rear axle pinion grease seal.

Refer to diesel engine service manual and attachment manual for additional required maintenance at this scheduled time period.

2000 HOURS: • Replace all air intake rubber components such as elbows and connectors - High temperatures in this area can cause the rubber to harden.

See AIR CLEANER MAINTENANCE in THIS SECTION • Replace hydraulic tank breather • Check all air intake tubing, rubber couplings and band clamps for signs of wear and leakage • Refer to diesel engine service manual and attachment manual for additional required maintenance at this scheduled time period.

EVERY 1500 HOURS: • Perform "frequently" maintenance • Perform 8 hour maintenance • Perform 125 hour maintenance

2 YEARS: • Replace engine coolant.

• Perform 250 hour maintenance

• Replace DEF supply module filter †.

• Perform 500 hour maintenance

• Refer to diesel engine service manual and attachment manual for additional required maintenance at this scheduled time period.

And in addition: • Replace crank case ventilation filter †. Refer to Engine Operation and Maintenance Manual for replacement instructions.

• Refer to diesel engine service manual and attachment manual for additional required maintenance at this scheduled time period.

Continued on next page

† Use of filters other than genuine Tigercat replacement filters is not recommended.

3.13

Lubrication and Maintenance

Tigercat 610E/615E Skidder

SCHEDULED MAINTENANCE SEASONAL: • Drain and refill hydraulic oil tank with recommended hydraulic oil. Refer to APPROVED HYDRAULIC OILS in THIS SECTION. Fill tank with grapple head fully open, grapple head and dozer blade on the ground until hydraulic oil level reaches the sight gauge full mark. Note that the oil level will drop 2 to 3 in (2 to 7.5 cm) when all cylinders are extended.

Check to ensure that the hydraulic oil type selected in the computer program matches the oil type being used. Adjust oil type if needed.

This will allow the program to optimize the cooling and s functions to best suite the oil being used.

Hydraulic oil grade information is shown on the main menu below the hydraulic oil temperature gauge. Operating outside the recommended operating range will shorten hydraulic component life. Refer to COMPUTER – ADJUSTMENT MENU - SERVICE SETTINGS – HYDRAULIC OIL GRADE in SECTION 2 of the OPERATOR'S MANUAL or SECTION 6 of the SERVICE MANUAL, for hydraulic oil grade selection settings information.

• For 610E machines drain and refill front and rear axles. Refer to LUBRICATION AND SERVICE CHART in THIS SECTION for recommended gear oils. Refer also to AXLE – AXLE LEVEL CHECK, FILL AND DRAIN LOCATIONS in THIS SECTION. • For 615E machines drain and refill front axle and bogie axle differential, housings and planetary drives. Refer also to LUBRICATION AND SERVICE CHART in THIS SECTION for recommended gear oils.

Refer to AXLE – AXLE LEVEL CHECK, FILL AND DRAIN LOCATIONS and AXLE – REAR (BOGIE) AXLE (IF APPLICABLE) in THIS SECTION. • Drain and refill pressurized water system (if equipped). Refer to PRESSURIZED WATER SYSTEM MAINTENANCE in THIS SECTION. • Perform service brake wear plate inspection.

Refer to SECTION 8 in the SERVICE MANUAL.

† Use of filters other than genuine Tigercat replacement filters is not recommended.

3.14

Tigercat 610E/615E Skidder

Lubrication and Maintenance

APPROVED HYDRAULIC OILS Use only one of the following oils to fill or replenish the MAIN HYDRAULIC SYSTEM.

3.15

Lubrication and Maintenance MACHINES 6101101 TO 6102500 REAR DRIVE SHAFT BEARING 21 1 FTG/8

27

Tigercat 610E/615E Skidder

MID DRIVE SHAFT

FRONT DRIVE SHAFT 21 1 FTG/500

1 FTG/8

5

GRAPPLE YOKE

8 FTG/8

13

4

3 4A

10

610E 14 12

6

27

GRAPPLE SNUBBERS 27 2 FTG/8 GRAPPLE ROTATOR 27 2 FTG/125 5 SHOTS

GRAPPLE PINION GEAR 27 1 FTG/250 5 SHOTS NOTE: REMOVE PIPEPLUG TO ACCESS

1

STEER CYLINDERS 23 4 FTG/8

AXLE-PIVOT, FRONT 20 2 FTG/8

16

14 620E/630E

DOOR HINGES

ARCH

8 FTG/500

24

12 FTG/8

25

28

11 12

13

7

15

8

9

10 2

17 CENTER JOINT

2 FTG/8

GRAPPLE

27

8 FTG/8

18

19

AXLE PINION

1 FTG/1000

19

22

AXLE PINION

1 FTG/1000

DOZER

6 FTG/8

18

26

LEGEND

* ANTIFREEZE SOLUTION MUST MEET GM 6038M SPECIFICATIONS - SEE MANUFACTURERS MAINTENANCE MANUAL ** STEER MACHINE FULLY BEFORE GREASING MID DRIVE SHAFT SLIP YOKE. *** MAY USE UP TO BUT NOT MORE THAN 1 LITER OF LUBRIZOL 6178, DSL-178, OR EQUA-TORQUE 2411 OR 2414 (FRONT AXLE ONLY, BRAKE NOISE REDUCTION).

LUBRICATION POINT WITH A DESIGNATED NUMBER OF FITTINGS (2FTG) 2 FTG/125 AND HOURS BETWEEN SERVICING (125 ). JOINT TO BE PURGED. USE

LITHIUM BASED GREASE CONTAINING MOLYBDENUM DISULFIDE.

USE OF FILTERS OTHER THAN GENUINE Tigercat REPLACEMENT FILTERS IS NOT RECOMMENDED. ®

3.16

CHK REP DRN D/R LUB

..... ..... ..... ..... ..... .....

HOURS CHECK REPLACE DRAIN DRAIN AND REFILL LUBRICATE

Tigercat 610E/615E Skidder

Lubrication and Maintenance

Tigercat Model 610E/620E/630E SERVICE AND LUBRICATION POINTS

REFER TO Tigercat OPERATOR'S MANUAL FOR FURTHER INFORMATION

1

COOLING SYSTEM

2

ENGINE OIL/FILTER

3

CRANK CASE VENTILATION FILTER

4

FUEL FILTER

4A 5

FUEL FILTER/WATER SEPARATOR

CHANGE COOLANT EVERY 2 YEARS

CHK

•

•

•

1

•

REP

• SEE ENGINE MANUFACTURER'S OPERATION AND MAINTENANCE MANUAL FOR PROCEDURES AND CAPACITIES

1

•

DEF SUPPLY MODULE FILTER

60% ANTIFREEZE * 40% DISTILLED WATER

•

REP

DRN

QTY

USG

DESCRIPTION

34.4 9.1

REP

CHK

LITERS

2000 6

CAPACITY 1500 6

1000 6

500 6

250 6

86

ITEM

125 6

SERVICE POINT NO.

SERVICE EVERY

REP

1

CHANGE FILTER EVERY 2 YEARS

1

CHK

1

REFER TO SECTION 3 OF THE MANUAL FOR DETAILS.

6

FUEL TANK FILLER SCREEN

7

AIR INTAKE PRECLEANER/INLET HOOD

CHK

1

CLEAN AS REQUIRED.

AIR INTAKE PRIMARY ELEMENT

CHK

1

AIR INTAKE SAFETY ELEMENT

CHK

1

CHECK FILTER RESTRICTION INDICATOR. REFER TO 8 HOUR SCHEDULED MAINTENCE FOR DETAILS.

9

AIR CLEANER UNLOADER VALVE

CHK

1

REFER TO SECTION 3 IN MANUAL

10

AIR INTAKE CONNECTIONS

CHK

1

CHECK FOR LOOSE CLAMPS AND DAMAGED RUBBER COMPONENTS. REPLACE RUBBER COMPONENTS.

11

HYDRAULIC TANK, 620E, 630E HYDRAULIC TANK, 610E

CHK

1

DRAIN AND REFILL AS REQUIRED BY SEASONAL OIL CHANGE. (SEE HYDRAULIC OIL CHART)

12

HYDRAULIC FILTER, FULL FLOW, INCLUDES: 1 BLUE WATER ABSORBING ELEMENT * 1 WHITE HIGH PERFORMANCE FILTER

REP †

2

*NOTE: MUST USE: 1 BLUE FILTER ELEMENT. 1 WHITE FILTER ELEMENT.

13

CHARGE PRESSURE FILTER

REP †

1

CHECK FILTER RESTRICTION INDICATOR ON FILTER WITH ENGINE RUNNING AT FULL AND WITH OIL FLOW.

14

EHS TRANSMISSION FILTER (OPTIONAL)

REP †

15

HYDRAULIC TANK BREATHER

16

PRESSURIZED WATER SYSTEM

CHK

17

TRANSMISSION TRANSMISSION, EHS (OPTIONAL)

CHK

18

AXLES, STANDARD DUTY : FRONT 610E FRONT 620E, 630E REAR AXLES, SEVERE DUTY : FRONT REAR

19

PINION GREASE SEAL - FRONT AND REAR AXLE

20

AXLE-PIVOT (FRONT ONLY)

8

22

REP 100 26.4 90 23.5

1 REP

TEST

D/R

1 52

13.7

6 10

1.6 2.6

1

FILL WITH MIL-L-2105C OR API-GL-5 LUBRICANT GRADE 75W-90

D/R ***

25.6 6.8 37 9.8 40.5 10.7 36 9.5 36 9.5

1 1 1 1 1

FILL WITH MIL-L-2105C OR API-GL-5 LUBRICANT GRADE/WEATHER TEMPERATURE: BELOW -10°F(-23°C) USE 75W-90 UP TO 100°F(38°C) USE 80W-90 ABOVE 100°F(38°C) USE 85W-140

LUB

PURGE

2

ONE FITTING PER AXLE LITHIUM BASE EP2 GREASE 

PURGE

2

LITHIUM BASE EP2 GREASE 

D/R

CHK

LUB

FRONT DRIVE SHAFT 21

REP

LUB

MID DRIVE SHAFT

LUB **

REAR DRIVE SHAFT BEARING

LUB

CENTER JOINT

LUB

CENTER JOINT BEARING PRELOAD

CHK 48 

SEASONAL DRAIN AND REFILL.

1 PURGE

1

LITHIUM BASE EP2 GREASE 

1 PURGE

2

LITHIUM BASE EP2 GREASE  REFER TO SECTION 3 OF THE MANUAL FOR DETAILS.

CHK

23

STEERING CYLINDERS

LUB

PURGE

4

LITHIUM BASE EP2 GREASE 

24

SINGLE ARCH CYLINDER & PIVOTS

LUB

PURGE

6

LITHIUM BASE EP2 GREASE 

25

DOUBLE ARCH CYLINDER & PIVOTS

LUB

PURGE

12

LITHIUM BASE EP2 GREASE 

26

DOZER BLADE CYLINDER & PIVOTS

LUB

PURGE

6

LITHIUM BASE EP2 GREASE 

27

GRAPPLE, Tigercat

28

WINCH: CARCO ALLIED

SEE LUBRICATION POINTS DIAGRAM CHK

D/R

59686B LUBECHART- R4.PDF 3/15

3.17

12 3.8

3 1

REFER TO WINCH MAINTENANCE IN SECTION 3 OF MANUAL. SEE ALSO WINCH MANUFACTURER'S MANUAL.

Lubrication and Maintenance MACHINES 6151001 TO 6151500 21

18

Tigercat 610E/615E Skidder

MID DRIVE SHAFT

REAR DRIVE SHAFTS 25 2 FTG/8

AXLE PINION

1 FTG/1000

1 FTG/8

25

3 4A

13

4

5 14 615E

BOGIE AXLE SLEWING RINGS 615E 22

24 FTG/250

BOGIE AXLE SLEWING RINGS 635E 23

4 FTG/1000

GRAPPLE YOKE

8 FTG/8

30

GRAPPLE SNUBBERS 30 2 FTG /8 GRAPPLE ROTATOR

2 FTG/125 5 SHOTS

30

GRAPPLE PINION GEAR 30 1 FTG/250 5 SHOTS

27

AXLE-PIVOT, FRONT 24 2 FTG/8

STEER CYLINDERS

4 FTG/8

6

14 635E 1

16

DOOR HINGES

ARCH

8 FTG/500

28

12 FTG/8

NOTE: REMOVE PIPEPLUG TO ACCESS

12

11 12 7 13 15

31

8

9

10 2

17

CENTER JOINT

GRAPPLE 30

8 FTG/8

20

26

FRONT DRIVE SHAFT 25 1 FTG/500

2 FTG/8

AXLE PINION 18

DOZER

6 FTG/8

19

29

1 FTG/1000

LEGEND * ANTIFREEZE SOLUTION MUST MEET GM 6038M SPECIFICATIONS - SEE MANUFACTURERS MAINTENANCE MANUAL ** STEER MACHINE FULLY BEFORE GREASING MID DRIVE SHAFT SLIP YOKE. *** MAY USE UP TO BUT NOT MORE THAN 1 LITER OF LUBRIZOL 6178, DSL-178, OR EQUA-TORQUE 2411 OR 2414 (FRONT AXLE ONLY, BRAKE NOISE REDUCTION).

LUBRICATION POINT WITH A DESIGNATED NUMBER OF FITTINGS (2FTG) AND HOURS BETWEEN 2 FTG/125 SERVICING (125 ). JOINT TO BE PURGED. ♦ USE LITHIUM BASED GREASE CONTAINING MOLYBDENUM DISULFIDE. † USE OF FILTERS OTHER THAN GENUINE TIGERCAT REPLACEMENT FILTERS IS NOT RECOMMENDED.

3.18

CHK REP DRN D/R LUB

HOURS CHECK REPLACE DRAIN DRAIN AND REFILL LUBRICATE

Tigercat 610E/615E Skidder

Lubrication and Maintenance

Tigercat Model 615E/635E SERVICE AND LUBRICATION POINTS

REFER TO Tigercat OPERATOR'S MANUAL FOR FURTHER INFORMATION

3

CRANKCASE VENTILATION FILTER

4

FUEL FILTER

4A

FUEL FILTER/WATER SEPARATOR

CHK

REP

•

•

34.4

9.1

•

•

REP

60/40 ANTIFREEZE *

1

•

REP

QTY

2000 

1500 

1000 

500 

250 

8 ENGINE OIL/FILTER

CHANGE COOLANT EVERY 2 YEARS

CHK

DESCRIPTION USG

2

COOLING SYSTEM

CAPACITY LITERS

1

ITEM

125 

SERVICE POINT NO.

SERVICE EVERY

•

1

REP

1

CHANGE FILTER EVERY 2 YEARS

1

CHK

1

DRN

• SEE ENGINE MANUFACTURER'S OPERATION AND MAINTENANCE MANUAL FOR PROCEDURES AND CAPACITIES REFER TO SECTION 3 OF THE MANUAL FOR DETAILS.

5

DEF SUPPLY MODULE FILTER

6

FUEL STRAINER

7

AIR INTAKE PRECLEANER/INLET HOOD

CHK

1

CLEAN AS REQUIRED

AIR INTAKE PRIMARY ELEMENT

CHK

1

AIR INTAKE SAFETY ELEMENT

CHK

1

CHECK FILTER RESTRICTION INDICATOR. REFER TO 8 HOUR SCHEDULED MAINTENANCE FOR DETAILS.

9

AIR CLEANER UNLOADER VALVE

CHK

1

REFER TO SECTION 3 IN MANUAL

10

AIR INTAKE CONNECTIONS

CHK

1

CHECK FOR LOOSE CLAMPS AND DAMAGED RUBBER COMPONENTS. REPLACE RUBBER COMPONENTS.

11

HYDRAULIC TANK - 635E HYDRAULIC TANK - 615E

CHK

1

DRAIN AND REFILL AS REQUIRED BY SEASONAL OIL CHANGE (SEE HYDRAULIC OIL CHART)

12

HYDRAULIC FILTER, FULL FLOW, INCLUDES: 1 BLUE WATER ABSORBING ELEMENT * 1 WHITE HIGH PERFORMANCE FILTER

2

*NOTE: MUST USE 1 BLUE FILTER ELEMENT AND 1 WHITE FILTER ELEMENT

13

CHARGE PRESSURE FILTER

1

CHECK FILTER RESTRICTION INDICATOR ON FILTER WITH ENGINE RUNNING AT FULL AND WITH OIL FLOW

14

EHS TRANSMISSION FILTER (OPTIONAL)

15

HYDRAULIC TANK BREATHER

16

PRESSURIZED WATER SYSTEM

17

TRANSMISSION TRANSMISSION, EHS (OPTIONAL)

8

18

PINION GREASE SEAL

19

AXLES, STANDARD DUTY : FRONT - 615E AXLES, SEVERE DUTY : FRONT - 615E, 635E

20

BOGIE AXLE - DIFFERENTIAL

21

BOGIE AXLE - HOUSINGS

22

BOGIE AXLE - SLEWING RINGS - 615E

23

BOGIE AXLE - SLEWING RINGS - 635E

24

AXLE - PIVOT (FRONT ONLY)

26

REP 100 26.4 90 23.5 REP

†

REP

†

REP

1

†

REP CHK

TEST

D/R

CHK

D/R

CHK CHK

1 52

13.7

6 10

1.6 2.6

SEASONAL DRAIN AND REFILL 1

LUB

PURGE

2

D/R ***

37 36

9.7 9.5

1

D/R

246

LUB LUB LUB

FRONT DRIVE SHAFT 25

REP

LUB

FILL WITH MIL-L-2105C OR API-GL-5 LUBRICANT GRADE 75W-90 LITHIUM BASE EP2 GREASE  FILL WITH MIL-L-2105C OR API-GL-5 LUBRICANT GRADE/WEATHER TEMPERATURE: BELOW -10°F(-23°C) USE 75W-90 UP TO 100°F(38°C) USE 80W-90 ABOVE 100°F(38°C) USE 85W-140

65

3

PURGE

24

LITHIUM BASE EP2 GREASE 

PURGE

4

LITHIUM BASE EP2 GREASE  LITHIUM BASE EP2 GREASE 

PURGE

2

PURGE

1

MID DRIVE SHAFT

LUB **

PURGE

1

REAR DRIVE SHAFT: BEARINGS

LUB

PURGE

2

CENTRE JOINT

LUB

PURGE

2

CENTRE JOINT BEARING PRELOAD

CHK 48

LITHIUM BASE EP2 GREASE 

LITHIUM BASE EP2 GREASE  REFER TO SECTION 3 OF THE MANUAL FOR DETAILS

CHK

27

STEERING CYLINDERS

LUB

PURGE

4

28

DOUBLE ARCH CYLINDER & PIVOTS

LUB

PURGE

12

LITHIUM BASE EP2 GREASE 

29

DOZER BLADE CYLINDER & PIVOTS

LUB

PURGE

6

LITHIUM BASE EP2 GREASE 

30

GRAPPLE, Tigercat

31

WINCH: CARCO ALLIED

LITHIUM BASE EP2 GREASE 

SEE LUBRICATION POINTS DIAGRAM CHK

D/R

59690B LUBECHART- R4.PDF 3/15

3.19

12 3.8

3 1

REFER TO WINCH MAINTENANCE IN SECTION 3 OF MANUAL. SEE ALSO WINCH MANUFACTURER'S MANUAL.

Lubrication and Maintenance FILTERS IMPORTANT !

Failure to service and replace filters at the proper intervals specified in the manufacturer's manuals, could cause damage to the machine and result in the product warranty becoming NULL and VOID. Check Tigercat parts catalog for replacement filters.

PRIMARY FUEL FILTER AND SECONDARY FUEL FILTER/WATER SEPARATOR This machine is equipped with two fuel filters. The primary fuel filter is on the engine. The secondary fuel filter/water separater is a combination unit, with a replaceable fuel filter and a removable water sediment bowl on the bottom of the unit.

The water sediment bowl is only replaced if it becomes damaged or non-functional. For service and replacement intervals see SERVICE AND LUBRICATION POINTS in THIS SECTION.

Tigercat 610E/615E Skidder WARNING The fuel pump high-pressure fuel lines and fuel rail contain very high pressure fuel.

Never loosen any fittings while the engine is running. Personal injury and property damage can result.

Changing the primary fuel filter: Refer to ENGINE OPERATION AND MAINTENANCE MANUAL for primary fuel filter replacement instructions.

WARNING

Drain fuel filter into a container and dispose of all fluids properly.

HAND PRIMER SECONDARY FUEL FILTER/ WATER SEPARATOR PRIMARY FUEL FILTER

WATER IN FUEL SENSOR DRAIN VALVE 610E-019

FUEL WATER SEPARATOR

3.20

Tigercat 610E/615E Skidder

Lubrication and Maintenance

Changing the secondary fuel filter/water separator:

HAND PRIMER

1. Park machine on level ground, install articulation lock bar, lower dozer and grapple to the ground, stop engine, engage parking brake and block wheels.

2. Wipe clean the area around the filter and head.

SECONDARY FUEL FILTER/ WATER SEPARATOR

3. Attach a hose to the spout on the bowl drain and place a suitable drain pan under separator bowl drain hose.

4. Loosen vent plug on filter head, open drain on separator bowl and drain fuel into pan.

5. Disconnect the fuel heater and water in fuel sensor from the wiring harness.

WATER IN FUEL SENSOR

6. Remove the water separator filter and bowl from the filter head.

DRAIN VALVE

7. Remove and discard the gasket from the filter head.

630E-291

8. Remove the water sediment bowl from the bottom of the old filter. Discard this gasket also. Dispose of old filter and any fuel properly.

FUEL WATER SEPARATOR PRIMER PUMP

GASKET

9. Clean the water sediment bowl, seating area for the gaskets on the filter head and the sediment bowl and close bowl drain.

FUEL WATER SEPARATOR

10. Lubricate gasket for bottom of filter and water sediment bowl with clean engine oil and carefully hand tighten the water sediment bowl onto the new filter. Close the water drain valve.

GASKET WATER SEPARATOR BOWL

11. Lubricate the gasket on top of the new filter with clean engine oil.

BOWL DRAIN

12. Screw the new filter onto the filter head until the gasket makes contact with the seat and then hand tighten an additional 3/4 turn only.

FUEL/WATER SEPARATOR

13. Reconnect the fuel heater and water in fuel sensor to the wiring harness.

WARNING Drain fuel filter into a container and dispose of all fluids properly.

14. Use primer pump to refill filter until fuel free of air flows from vent on top of filter head, then tighten vent plug.

15. Start the engine and check for leaks.

16. Clean up any spilled fuel before returning machine to operation.

IMPORTANT !

Filters that are an integral part of the engine (fuel and lubricating oil) should be serviced and replaced according to the engine manufacturer's manual.

3.21

Lubrication and Maintenance

Tigercat 610E/615E Skidder

FUEL TANK STRAINER This is a stainless steel fuel strainer, screwed on to the inlet pipe of the engine fuel feed line inside at the bottom of the fuel tank.

RIGHT HAND TANK REAR COVER

Changing or cleaning the strainer: NOTE: This should only be required if excessive quantities of foreign material has built up inside the tank.

LEFT HAND TANK

1. Park machine on level ground, install articulation lock bar, lower dozer and grapple to the ground , stop engine, engage parking brake and block wheels.

620E-062

2. Drain the fuel tank. Refer to DRAINING THE FUEL TANK in THIS SECTION.

STANDARD FUEL TANKS FUEL TANK FILL CAP

3. Remove the round fuel tank cover plate and “O” ring from the access hole.

REAR COVER

4. Before removing the strainer, clean any debris from the bottom of the tank and wipe it clean.

5. Remove the fuel strainer using the hex on the end of strainer. Carefully clean the strainer (it may be damaged by rough handling).

6. Check for a buildup of foreign materials where the strainer threads on to the pipe and elbow.

7. Reinstall the strainer using the hex on end.

8. Reinstall fuel tank cover plate with “O” ring.

9. Refuel and check for leaks. Start the engine and check for leaks again.

620E-062

HIGH CAPACITY FUEL TANK

DRAINING THE FUEL TANK 1. The fuel system is equipped with either two standard saddle tanks or a single high capacity tank.

2. Use the fuel gauge on the computer display or the dipstick to estimate the container capacity required to properly drain the fuel.

Refer to FUEL TANK in SECTION 2 of the OPERATOR'S MANUAL for tank capacities.

3. Remove the fuel fill cap.

4. Remove the drain plugs and drain the fuel into a suitable container.

Note that both the left and right sides of the high capacity tank need to be drained to fully empty this tank.

S≤15 mg/kg

5. Once the fluid has been drained replace the drain plugs and fuel fill cap.

ULTRA LOW SULFUR FUEL ONLY 36686AUNI R0

3.22

Tigercat 610E/615E Skidder

Lubrication and Maintenance

REFUELLING Park machine on level ground, turn the engine off and allow machine to cool.

DO NOT refuel while smoking or near an open flame or sparks.

Clear obstructions from steps and handles needed to access fuel tank.

Open cover on top of fuel tank (if equipped)and clear any debris from around the fuel fill cap.

Remove fuel fill cap slowly to allow pressure to escape from tank.

Inspect fuel fill cap gasket.

Inspect fuel strainer located under the fill cap for debris or damage.

Attach a grounding strap to an unpainted metal surface on the machine if the refuelling tank or nozzle is so equipped.

Fill tank until fuel level reaches the fuel strainer or the full mark on the sight gauge if equipped. Do not leave nozzle unattended or spillage may occur.

Remove nozzle and ground strap (if applicable), then install fuel fill cap hand tight before closing fill cap cover.

Before restarting the machine, check that no other personnel have moved into the hazardous area and sound the horn.

3.23

Lubrication and Maintenance

Tigercat 610E/615E Skidder

DEF SUPPLY MODULE FILTER The supply module is located on the right side of the engine compartment.

The DEF supply module filter should be replaced as part of scheduled maintenance every 2 years.

Changing filter: 1. Park machine on level ground, install articulation lock bar, lower dozer and grapple to ground, stop engine, engage parking brake and block wheels.

2. Wipe clean the area around the filter and supply module.

3. Place rags below to catch the spills.

630E-284

7. Insert the tool edge completely until a click is felt or heard.

630E-281

4. Turn the filter cover counterclockwise to remove from the supply module. Use a 27 mm (1 1/16 in) wrench.

630E-286

8. Pull out the filter, using a tool in the slot on the filter removal tool if required.

630E-282

5. Remove the equalizing element and note the colour of the filter inside (black or grey).

630E-287

9. Clean surfaces with water only to avoid DEF contamination.

Check the area around the filter for cracks. If cracks are found the supply module must be replaced.

630E-285

6. Find the filter removal tool provided with the replacement parts select the correct edge BLACK (B) for black filters or GREY (G) for grey filters.

3.24

Tigercat 610E/615E Skidder

Lubrication and Maintenance WARNING Use only diesel exhaust fluid (DEF) which meets ISO 22241 specifications. NEVER fill the DEF tank with any other fluid.

DEF fluid is injected into the exhaust gas stream during normal operation of the Selective Catalytic Reduction (SCR) aftertreatment system.

Use of other fluids may cause component damage, or a fire risk which could result in death or serious injury.

630E-288

10. Install the new filter. Lubricate the o-rings on the filter with clean DEF solution for easy installation.

630E-289

11. Install the new equalizing element.

Note that the equalizing element must be replaced with each filter change.

630E-290

12. Install the new filter cover, tighten to 20 Nm (15 lbf-ft). Use a 27 mm (1 1/16 in) wrench.

Note that the filter cover must be replaced with each filter change.

13. Start the engine and check for leaks.

IMPORTANT! It is important to avoid contamination of DEF when performing maintenance on the system as this may cause costly damage to SCR system components and affect the proper operation of the aftertreatment system and the engine.

3.25

Lubrication and Maintenance

Tigercat 610E/615E Skidder

DRAINING THE DIESEL EXHAUST FLUID TANK The DEF tank is located in the compartment below the right hand cab door.

DEF TANK (BLUE FILL CAP)

TO DRAIN THE TANK: 1. Use the DEF level indicator on the computer display to estimate the container capacity required to properly drain the DEF solution. Total tank capacity is 43 L (11.4 US gal).

41581AUNI R0

630E-269

2. Remove the DEF tank drain access cover.

3. Remove the DEF fill cap. The DEF quality sensor location can be used as a drain (remove the sensor carefully to avoid damage).

4. Drain the DEF solution into a suitable container.

5. Once the fluid has been drained, clean the inside of the tank with DEF fluid or distilled/ demineralized water only if required.

Thoroughly drain the tank after cleaning

DEF TANK

610E-005

6. Replace the quality sensor and DEF fill cap.

If any DEF fluid has spilled, rinse well with water.

QUALITY SENSOR

NOTE: To avoid contamination and ensure clean fluid, do not re-use DEF. Re-fill tank with new DEF only.

IMPORTANT! It is important to avoid contamination of DEF when performing maintenance on the system as this may cause costly damage to SCR system components and affect the proper operation of the aftertreatment system and the engine.

610E-011

WARNING Use only diesel exhaust fluid (DEF) which meets ISO 22241 specifications. NEVER fill the DEF tank with any other fluid.

DEF fluid is injected into the exhaust gas stream during normal operation of the Selective Catalytic Reduction (SCR) aftertreatment system.

Use of other fluids may cause component damage, or a fire risk which could result in death or serious injury.

3.26

DEF TANK DRAIN ACCESS

Tigercat 610E/615E Skidder

Lubrication and Maintenance

HYDRAULIC OIL DOUBLE ELEMENT FILTERS HYDRAULIC TANK

HYDRAULIC FILTER SERVICING GUIDELINES

DOUBLE ELEMENT FILTER

NEVER PRE-FILL HYDRAULIC FILTERS

Tigercat does not recommend the pre-filling of spin-on filters due to the risk of damage to the hydraulic system caused by unfiltered oil. Unfiltered oil used to pre-fill filters enters directly into the hydraulic circuit.

Contaminants in unfiltered oil can cause significant and costly damage to hydraulic valves, pumps and motors. The cleanliness of hydraulic oil cannot be guaranteed unless it is always prefiltered before use.

BREATHER

BLUE ELEMENT SIGHT GAUGE

LEVEL SWITCH

WARNING CHARGE PRESSURE FILTER

610E-016

HYDRAULIC TANK, FILTERS AND SIGHT GAUGE

WARNING, HOT FLUIDS AND HOT MACHINE SURFACES CAN CAUSE SERIOUS BURNS!

The hydraulic oil cooling circuit contains a double filter head with a built in 25 psi (1.7 bar) bypass valve. In the event of a clogged filter element or thicker oil on cold starts, this bypass filter will open and redirect oil around the filter element. It is recommended that all machines use two different filter elements: 1 white, Tigercat high performance, full flow hydraulic oil filter element 1 blue, Tigercat water absorbing, full flow hydraulic oil filter element.

Refer to SCHEDULED MAINTENANCE and SERVICE AND LUBRICATION AND SERVICE POINTS in THIS SECTION. IMPORTANT !

Contaminated hydraulic oil can lead to premature failure of hydraulic components and costly repairs.

Filters must be replaced at the recommended time intervals. Refer to SCHEDULED MAINTENANCE in SECTION 3 of THIS MANUAL. Use of hydraulic filters other than the Tigercat brand could lead to severe wear and rapid failure of hydraulic system components.

3.27

•

Before servicing the machine, allow the engine cooling system, fuel system, exhaust system, hydraulic system and machine surfaces to cool down.

•

Use a thermometer to check surface and system temperatures to ensure it is safe to begin service work.

•

DO NOT begin service work until the surface or system temperature has cooled down to below 100°F (38°C)!

Lubrication and Maintenance

Tigercat 610E/615E Skidder

Changing the filters:

HYDRAULIC TANK

1. Park machine on level ground, install articulation lock bar, lower dozer and grapple to ground, stop engine, engage parking brake and block wheels.

DOUBLE ELEMENT FILTER

2. Wipe clean the area around the filter and head.

BREATHER

3. Place rags below to catch the spillage of oil.

BLUE ELEMENT

4. Wearing face protection (in case of an oil squirt), unscrew the old filter. Dispose of old filter and any oil properly.

SIGHT GAUGE

5. The new Tigercat filter is supplied with two gaskets enclosed, examine the filter head closely to determine which gasket should be used and follow the instructions to ensure proper installation.

LEVEL SWITCH

FILTER HEAD

CHARGE PRESSURE FILTER

GASKET

FILTER ELEMENT

HYDRAULIC TANK, FILTERS AND SIGHT GAUGE Tighten filter until top edge makes metal to metal contact with filter head. (approximately 1 1/2 additional turns after gasket contact)

610E-016

FILTR_SEALS 2

SQUARE SECTION GASKET INSTALLATION

 Square Section Gasket Remove used gasket and clean groove in head.

Apply clean oil to new gasket surfaces.

Install new gasket into groove in filter head.

Screw on new filter until gasket makes contact.

Tighten filter an additional 3/4 turn.

6. Start the engine and check for leaks.

HYDRAULIC FILTER SERVICING GUIDELINES

FILTER HEAD

NEVER PRE-FILL HYDRAULIC FILTERS

GASKET

Tigercat does not recommend the pre-filling of spin-on filters due to the risk of damage to the hydraulic system caused by unfiltered oil. Unfiltered oil used to pre-fill filters enters directly into the hydraulic circuit.

Contaminants in unfiltered oil can cause significant and costly damage to hydraulic valves, pumps and motors. The cleanliness of hydraulic oil cannot be guaranteed unless it is always prefiltered before use.

FILTER ELEMENT FILTR_SEALS 2

'O' RING GASKET INSTALLATION

 'O' Ring Gasket Remove used gasket and clean gasket seat in head.

Apply clean oil to new gasket surfaces.

Install new gasket on inside lip of filter.

Screw on new filter until gasket makes contact.

3.28

Tigercat 610E/615E Skidder CHARGE PRESSURE FILTER The charge circuit contains a single element, full flow Tigercat hydraulic filter with a 50 psi (3.5 bar) third port bypass valve. When a restriction is encountered, the bypass valve diverts oil back to tank via the third port to prevent unfiltered oil from entering the charge circuit.

Lubrication and Maintenance EHS TRANSMISSION FILTER EHS TRANSMISSION FILTER

Changing a pressure filter: 1. Park machine on level ground, install articulation lock bar, lower dozer and grapple to ground, stop engine, engage parking brake and block wheels.

LOCATED IN THE LEFT HAND STEP COMPARTMENT BELOW THE CAB DOOR

2. Wipe clean the area around the filter and head.

3. Place rags below to catch the spillage of oil.

4. Wearing face protection (in case of an oil squirt), unscrew the old filter.

5. Drain filter and dispose of any oil properly.

6. Check the seating area for the gasket on the filter head and wipe it clean.

7. This filter has an o-ring gasket. Replace o-ring as required and apply hydraulic oil to the gasket surface.

610E-036

EHS TRANSMISSION FILTER

The EHS transmission circuit is equipped with a full flow pressure filter with a 50 psi (3.5 bar) third port bypass valve. When a restriction is encountered the bypass valve diverts oil back to the transmission circuit reservoir in the transmission to prevent unfiltered oil from entering the transmission circuit.

Refer to SERVICE AND LUBRICATION POINTS for EHS transmission oil specifications.

10. Start the engine and check for leaks.

Changing a transmission filter: 1. Park machine on level ground, install articulation lock bar, lower dozer and grapple to ground, stop engine, engage parking brake and block wheels.

HYDRAULIC TANK BREATHER

2. Wipe clean the area around the filter and head.

8. Screw on the new filter until the gasket makes contact with the seat in the filter head.

9. Hand tighten filter an additional 1/2 turn only.

The hydraulic tank breather is located beside the double element filters. This breather should be replaced every 2000 hours.

3. Place rags below to catch the spillage of oil.

4. Wearing face protection (in case of an oil squirt), unscrew the old filter.

5. Drain filter and dispose of any oil properly.

6. Check the seating area for the gasket on the filter head and wipe it clean.

7. This filter has an o-ring gasket. Replace o-ring as required and apply transmission oil to the gasket surface.

8. Screw on the new filter until the gasket makes contact with the seat in the filter head.

9. Hand tighten filter an additional 1/2 turn only.

DO NOT use bottom nut for filter installation or damage/leakage may result. Bottom nut is to assist in filter removal only.

10. Start the engine and check for leaks.

3.29

Lubrication and Maintenance

Tigercat 610E/615E Skidder

DRAINING HYDRAULIC TANK

CAUTION

QUICK CONNECT TO SUCTION HOSE

Perform the hydraulic tank drain when the hydraulic oil temperature is below 100°F (38°C), but warm enough to be viscous.

LOCATED ON THE RIGHT SIDE AT THE FRONT OF THE ENGINE COMPARTMENT

1. The hydraulic tank is equipped with a hose that routes from the bottom of the tank to the bottom of the front chassis belly pan.

PUMP SWITCH

2. The hose is plugged at the end and can be accessed by removing the belly pan door.

3. The drain hose for the hydraulic tank can be lowered from the belly of the chassis and positioned in a drip pan.

610E-009

HYDRAULIC FILL PUMP

IMPORTANT !

Contaminated hydraulic oil can lead to premature failure of hydraulic components and costly repairs.

Filters must be replaced at the recommended time intervals. Refer to SCHEDULED MAINTENANCE in SECTION 3 of THIS MANUAL.

4. Remove the plug in the hose end to drain tank.

5. Once fluid has been drained, replace the drain plug in the drain hose.

Use of hydraulic filters other than the Tigercat brand could lead to severe wear and rapid failure of hydraulic system components.

FILLING HYDRAULIC TANK Refer to APPROVED HYDRAULIC OILS in THIS SECTION. Refer to SERVICE AND LUBRICATION POINTS chart in THIS SECTION for hydraulic tank capacity.

HYDRAULIC OIL FILL SUCTION HOSE STORAGE LOCATION

1. Park machine on level ground, lower dozer blade and grapple (with head fully open) onto the ground.

2. Open right front engine compartment access door.

3. Get the hydraulic oil fill suction hose from its storage location. Clean the suction hose, connect to hydraulic fill pump and remove cap.

Insert end of suction tube into supply drum.

4. Operate pump using the pump switch, located on the right side at the front of the engine compartment. The oil is pumped directly into the hydraulic tank via the double element filter.

620E-050

Refer also to HYDRAULIC FILL PUMP in SECTION 2 of the OPERATOR'S MANUAL. 5. Observe the level gauges on the rear of the tank to determine when to release the switch.

Fill tank with grapple head fully open, grapple head and dozer blade on the ground. Fill tank until hydraulic oil level reaches the sight gauge FULL mark. Note that the oil level will drop 2 to 3 in (2 to 7.5 cm) when all cylinders are extended.

6. Replace cap on suction tube, wipe dry, disconnect and store. Close all access doors.

3.30

HYDRAULIC OIL FILL SUCTION HOSE STORAGE LOCATION BELOW LEFT HAND CAB DOOR

Tigercat 610E/615E Skidder

Lubrication and Maintenance

DRAINING ENGINE COOLANT

CAUTION

RADIATOR FILL CAP

DO NOT remove the radiator fill cap from a hot engine. Wait until coolant temp is below 122°F (50°C) before removing cap.

Only remove radiator fill cap when cool enough to touch with bare hands. Slowly loosen cap to first stop to relieve pressure before removing completely.

33952AUNI R0

RADIATOR FILL CAP

620E-025

1. The radiator is equipped with a hose to drain the contents of the radiator system fluid into a storage container.

2. Remove the front nose belly pan in the front chassis.

A/C CONDENSER

3. Remove the radiator fill cap.

CHARGE AIR COOLER (CAC)

RADIATOR

4. The radiator is located on the right hand side of the heat exchanger.

SHUT-OFF VALVE

DRAIN HOSE

610E-010

LOWER RADIATOR TUBE SPUD AND SHUT-OFF VALVE

The lower radiator tube is equipped with a spud and shut-off valve. The drain hose is attached to the shut-off valve.

5. Place the free end of the drain hose in a storage container and remove the gear clamp and bolt from the end of the hose.

620E-059

6. Slowly open the shut-off valve to drain the radiator fluid.

7. Once fluid has been drained, close the shut-off valve and replace the gear clamp and bolt on the drain hose.

3.31

COOLING ASSEMBLY

HYDRAULIC OIL COOLER

Lubrication and Maintenance

Tigercat 610E/615E Skidder

DRAINING TRANSMISSION OIL 1. The transmission is equipped with a plug to drain the contents of the transmission into a storage container.

2. Remove the belly pan in the front chassis closest to the articulation joint.

3. Remove the drain plug on the hydraulic motor side of the transmission (pic).

4. Once fluid has been drained, replace the drain plug in the transmission housing once draining has completed.

TRANSMISSION DRAIN 630C-100

TRANSMISSION OIL

3.32

Tigercat 610E/615E Skidder PARKING BRAKE (SPRING APPLIED HYDRAULIC RELEASE)

Lubrication and Maintenance PARKING BRAKE ADJUSTMENT For proper adjustment the parking brake must be released during this procedure.

1. Park machine on level ground, install articulation lock bar, lower dozer and grapple to the ground and block wheels.

Engine must be ON to operate parking brake switch for this procedure.

620D-223

PARKING BRAKE CALIPER (SPRING APPLIED HYDRAULIC RELEASE)

MANUAL RELEASE OF PARKING BRAKE For towing purposes or in the event of a failure of the pressure release the parking brake can be released manually using the following procedure: 1. If possible, park machine on level ground, install articulation lock bar, lower dozer and grapple to the ground, stop engine and block wheels.

2. Remove the cover (turn counterclockwise).

3. Loosen the lock nut (M20) and turn the adjusting screw counterclockwise until the brake disc is free.

2. Change the program mode from NORMAL to FUNCTION SETUP MODE and press OK. Using the IQAN MD3 from the main menu navigate to ADJUSTMENT MENU (F2) – SERVICE SETTINGS – Program Mode – Normal. Refer to COMPUTER – ADJUSTMENT MENU in SECTION 2 of the OPERATOR'S MANUAL or SECTION 6 of the SERVICE MANUAL

Note that a torque of 52 lbf-ft (70 Nm) will be required to loosen the adjusting screw and manually release the parking brake when the parking brake is engaged.

CAUTION

IMPORTANT !

Once the disc is free the parking brake is inoperable.

When setup program modes are chosen an information message is shown on the electronic display until the message is acknowledged.

4. Tighten the lock nut and reinstall the cover to protect to protect the brake from dirt.

5. When towing and/or repairs have been completed readjust the parking brake before resuming normal operations.

IMPORTANT !

Note that for some machines equipped with an EHS transmission the towing procedure does not require release of the parking brake. Refer to TOWING INSTRUCTIONS in SECTION 2 of the OPERATOR'S MANUAL for full towing instructions for this machine to avoid any damage due to improper towing.

In each program mode some controls are deactivated for safety during setup procedures. Attempting to use these controls will reactivate the information message.

3. With the aid of an assistant in the cab disengage the parking brake by placing the parking brake switch in the OFF position.

NOTE: As part of the interlock system this machine automatically engages the parking brake whenever a cab door is open. This prevents accidental or improper operation of the controls from anywhere but the operator's seat.

3.33

Lubrication and Maintenance

Tigercat 610E/615E Skidder

LOCK NUT

COVER

620D-224

ADJUSTING SCREW

4. Remove the cover (turn counterclockwise).

5. Loosen the lock nut (M20) and turn the adjusting screw clockwise until the two brake pads make contact with the brake disc.

6. Turn the adjusting screw counterclockwise 1/4 turn to set correct clearance.

14. Change the program mode from FUNCTION SETUP MODE back to NORMAL and press OK. Using the IQAN MD3 from the main menu navigate to ADJUSTMENT MENU (F2) – SERVICE SETTINGS – Program Mode – Normal. Refer to COMPUTER – ADJUSTMENT MENU in SECTION 2 of the OPERATOR'S MANUAL or SECTION 6 of the SERVICE MANUAL

7. Engage the parking brake by placing the parking brake switch in the ON position. Hold the adjusting screw in position and tighten the lock nut.

8. Cycle the parking brake OFF and ON, then OFF again.

IMPORTANT !

Machine must be in the Normal Program Mode to operate normally.

9. With the parking brake OFF, verify correct clearance between the two brake pads and the brake disc with a feeler gauge. Correct clearance is .020-.060 in (0.5-1.5 mm).

Other program modes are used for service/ setup procedures only.

10. Reinstall the cover.

When setup program modes are chosen an information message is shown on the electronic display until the message is acknowledged.

11. Remove articulation lock bar.

12. Engage the parking brake several times and check the braking efficiency on a slope.

In each program mode some controls are deactivated for safety during setup procedures. Attempting to use these controls will reactivate the information message.

13. If further adjustment is required repeat steps 1 to 12.

15. Stop engine.

3.34

Tigercat 610E/615E Skidder

Lubrication and Maintenance

SERVICE BRAKE CHECKING BRAKE AND ACCUMULATOR FOR PROPER OPERATION

Service Brake

The main pump supplies oil directly to the brake accumulator, via a check valve inside the main pump block to charge the accumulator to specified pressure. The accumulator is installed to ensure that the brake control remains responsive at all times by maintaining an optimum pilot pressure of 3000psi to the brake pilot valve. This oil from the accumulator side of the check valve is sent to the brake foot control valve.

Pressure Low. Service machine to correct.

8. If the Service Brake Pressure Low warning appears on the screen before the brake has been pumped 5 times from a full charge investigate the cause.

The accumulator when functioning properly will hold sufficient pressure for up to 5 brake applications after the engine stalls or is turned off, beyond this the pressure drops substantially.

Check first for leaks in the brake circuit. If no leaks are found check for proper operation of the brake pedal valve, accumulator, check valve and brake pressure sensor.

For more information about the service brake circuit refer to SECTION 9 of THE SERVICE MANUAL.

For more information about the service brake circuit refer to SECTION 9 of THE SERVICE MANUAL.

PROCEDURE: 1. Park machine on level ground, lower dozer and grapple to the ground, stop engine and engage parking brake and block wheels.

2. Release the pressure stored in the brake accumulator by fully applying the brake foot pedal repeatedly until there is no pedal resistance. This may take a minimum of 150 applications.

3. Start engine.

NOTE: The engine will not turn over unless the parking brake is ENGAGED. 4. Disengage parking brake to fully charge the accumulator. Run engine for 10 seconds, then shut engine off.

NOTE: When the parking brake is DISENGAGED full pressure is available from the main pump to the brake accumulator.

5. Engage the parking brake.

6. Fully apply the brake pedal 5 times. The accumulator pressure should remain above 800 psi (no warning on the computer display).

As the pressure drops in the accumulator the brake pedal will become spongy.

Once the pressure falls below 800 psi the Service Brake Pressure Low warning will appear on the screen.

3.35

Lubrication and Maintenance

Tigercat 610E/615E Skidder

DEPRESSURIZING SUSPENDED MACHINE ELEMENTS When operator controls cannot be used to lower suspended machine elements due to an engine stall or other machine malfunction, suspended elements can be lowered manually using this procedure.

1. When suspended the dozer blade, grapple, and arch/boom will tend to extend the hydraulic cylinders supporting them due to gravity.

WARNING

2. Remove the function valve cover in the rear chassis.

Use caution when working on top of the rear chassis, as there are many pinch areas between the arch, arch cylinders and winch.

DO NOT move arch when workers are in this area.

Use caution and follow all safety warnings when working in this area. Never stand under an object supported with hydraulics. Always use safety stands or a locking device.

Do not work under the arch without properly supporting the arch/grapple assembly.

NEVER move the arch/grapple assembly when workers are in this area.

3. Refer to the label in the valve compartment or this manual to locate valve section for the element you wish to lower. Locate the spool limiting set screw at the end of the spool section of interest.

Never stand under an object supported with hydraulics. Always use safety stands or a locking device.

4. Use a wrench to loosen the jam nut that secures the spool limiting set screw. Use an allen wrench to slowly turn the set screw clockwise (IN). Continue until the set screw starts to contact the spool inside the valve.

Movement of booms and cylinders could result in death or serious injury.

DO NOT perform work on valves or piping until boom and attachment are lowered to the ground and engine is shut off.

5. At this point the spool will allow pressurized oil on the rod side of the cylinder to travel to the valve tank port and thus lower the implement.

6. Repeat steps 3 to 5 for all raised implements.

7. Restore spool limiting set screws to their factory setting and secure jam nuts prior to operating the machine.

B

A

Factory settings are dozer section 6mm from the end of the screw to the tightened jam nut, all other sections 10mm.

SPOOL LIMITING SET SCREW

620D-09

MAIN VALVE FUNCTIONS

MAIN VALVE SPOOL LIMITING SET SCREWS

32849AUNI R0

3.36

Tigercat 610E/615E Skidder AIR CLEANER MAINTENANCE

ENGINE AIR PRECLEANER

Lubrication and Maintenance IMPORTANT !

For peak engine performance and maximum fuel economy, please ensure that the air precleaner is regularly checked and cleaned as required. All intake air tubes and clamps should be thoroughly inspected on a regular basis and any damaged or missing components should be replaced immediately.

3

3

610E-035

4

ENGINE AIR PRECLEANER

AIR PRECLEANER The engine air precleaner cleans engine air before it reaches the air cleaner filter elements.

It removes contaminants such as dust, powder, insects, rain and snow. The air precleaner should be checked every 8 hours to make sure that foreign materials have not plugged the intake area or the discharge louver area. Clean as required.

IMPORTANT !

The air precleaner must be check every 8 hours and cleaned as required.

If the inlet/precleaner is plugged causing a restriction to airflow, reduced engine performance and increased fuel consumption may result.

If a plugged inlet/precleaner is left too long excessive air intake restriction may damage the rubber air intake tube. A damaged air intake tube will lead to ingestion of dirt into the engine which may result in engine failure.

Note that the air filter restriction indicator may not function properly if the air intake tube is damaged.

2 1 5

630C-19

CENTRI® PRECLEANER OPERATION

OPERATION: 1. Air enters the precleaner.

2. Specially designed vanes move dirty air toward the impeller.

3. The spinning impeller spins the air creating centrifugal force to separate contaminants from the clean air.

4. Contaminants are blown out the discharge louver.

5. Clean air enters the intake to the air cleaner.

Engine failures due to improper maintenance are not covered by Tigercat or Engine Manufacturer’s Warranty and any such claim will be denied.

3.37

Lubrication and Maintenance

Tigercat 610E/615E Skidder

AIR CLEANER

AIR CLEANER UNLOADER VALVE

610E-007

AIR CLEANER UNLOADER VALVE

ENGINE AIR CLEANER

AIR CLEANER UNLOADER VALVE AIR CLEANER UNLOADER VALVE 610E-028

AIR CLEANER The air cleaner on this machine uses two filter elements, a primary element and a safety element accessible from the right side of the engine compartment.

This rubber valve on the tube of the air cleaner housing should be checked at the beginning of every shift. (8 hours) If this valve is missing, damaged or has become hard, it will cause the air cleaner to become ineffective. The valve should suck closed at 1/3 throttle.

To ensure maximum engine protection, it is important that the elements be serviced correctly and at proper servicing intervals.

A filter restriction indicator is mounted to the output side of the filter, this should show green when the engine is running under load. Service is required if the indicator shows red. This machine is also equipped with a switch used to send a signal to the computer control system in the event of a filter restriction.

This valve should be replaced every 1000 hours.

Remove the unloader valve from the tube of the air cleaner housing. Check and clean the valve.

A good valve should be soft and flexible. If it is plugged, be sure to check the filter elements as they may need replacing as well. Reattach the valve to the tube.

When operating in high dust conditions, the unloader valve should be checked and squeezed every 2 hours to release dust buildup.

Engine Air Intake Filter Restricted. Service Machine to correct.

When a signal is received from the restriction indicator switch on the engine air cleaner a warning message will be displayed. Refer to COMPUTER – MESSAGES - ALERT – ENGINE AIR INTAKE FILTER RESTRICTED in SECTION 2 of the OPERATOR'S MANUAL.

FILTER RESTRICTION SWITCH

AIR CLEANER

FILTER RESTRICTION INDICATOR

610E-008

ENGINE AIR CLEANER

FILTER RESTRICTION INDICATOR A filter restriction indicator is connected to the outlet side of the air filter. Replace the primary air filter when the indicator shows RED. This indicator provides a continuous reading whether the engine is running or is turned off. After replacing the filter, reset the indicator by pressing the reset button.

NOTE: Replace the safety element every third primary filter change.

3.38

Tigercat 610E/615E Skidder

Lubrication and Maintenance

INTAKE TUBING AND JOINTS

OUTLET TUBE

Check all air intake system components, rubber elbows, connector hoses, tubes and clamps for damage, hardening, wear, cracks, leaks, loose clamps or loose hanger bracket hardware at the beginning of every shift. (8 hours). Repair or replace defective parts immediately.

PRIMARY ELEMENT

Replace all air intake rubber components such as elbows and connectors every 2000 hours - High temperatures in this area can cause the rubber to harden.

SAFETY ELEMENT

In addition to the LUBRICATION AND MAINTENANCE SCHEDULE, the following instructions should also be noted.

The most common and damaging servicing problems are:

AIRCLEANER

AIR FILTER ELEMENTS

IMPORTANT STEPS TO FOLLOW WHEN CHANGING FILTER ELEMENTS

OVER SERVICING Filter elements increase in dust cleaning efficiency as dust builds up on the media. Looks can be deceiving. A filter that looks dirty is actually more efficient than one that is clean. A filter with dust build up on the media reaches nearly 100% dust cleaning efficiency. Only when a filter is so clogged with dirt that air restriction goes beyond engine manufacturer's guidelines, should a filter be replaced.

1. Release the cover latch gently to reduce the amount of dust dislodged.

NOTE: This does not apply to oil filters.

5. Check your old filter, It can help you detect foreign material on the sealing surface that is causing leakage.

IMPROPER SERVICING Engine exposure to dust during servicing is the largest single reason for engine damage due to dust.

Abrasive dust can easily enter the intake system once the air cleaner cover and protective filter element is removed for replacement. The safety element does reduce this risk but it should also be replaced at every third primary element change.

2. Avoid dislodging dust from filter element(s) by gently pulling the element off the outlet tube.

3. Always clean the sealing surface of the outlet tube before inserting a new filter element.

4. Always clean the inside of the outlet tube and filter housing.

NOTE: Filter elements should never be cleaned and reused. Cleaning causes dust to bypass the filter and be deposited on the inner surface of the filter media. The dust is then drawn directly into the engine.

6. Inspect the new filter for damage.

7. Insert the new filter properly. Apply pressure to the outer rim of the filter not the flexible centre.

8. Inspect connections and ducts for air tight fit.

Ensure that all clamps, bolts and connections are tight. Check rubber elbows for splits or wear points and replace as needed. Leaks in these locations send dust directly to the engine.

3.39

Lubrication and Maintenance DIESEL OXIDATION CATALYST / SELECTIVE CATALYTIC REDUCTION AFTERTREATMENT SYSTEM (DENOX 2.2 SYSTEM - TIER 4 FINAL)

Tigercat 610E/615E Skidder 8

7

The engine on this machine is equipped with a combination Diesel Oxidation Catalyst (DOC) and high efficiency Selective Catalytic Reduction (SCR) aftertreatment system to limit the nitrogen oxide exhaust gas values (NOX) to meet Tier 4 Final emission standard requirements with low fuel consumption. This process is electronically controlled by the DENOX 2.2 system.

The diesel oxdation catalyst (DOC) uses oxidation at high temperatures to convert carbon monoxide (CO), hydrocarbons (HC) and the soluble organic fraction (SOF) of diesel particulates into inert compounds, carbon dioxide (CO2) and water vapour (H2O). In addition the DOC converts nitrogen oxide (NO) into nitrogen dioxide (NO2).

Increased NO2 levels enhance the performance of the SCR catalyst at low temperatures and increase the effectiveness of the DOC/SCR aftertreatment system as a whole.

14 610E-033

15

16

12

View A

The high efficiency SCR process is based on a series of chemical reactions which involve the reaction of ammonia with the oxygen in the exhaust gas to reduce nitrogen oxides (NOX) in the exhaust gas by transforming it into inert compounds: free nitrogen (N2) and water vapour (H2O). In addtion the high efficiency catalytic converter includes a clean up catalyst (CUC) which reduces any excess ammonia (NH3) which may result from the SCR process.

2

IMPORTANT !

When cleaning the machine with pressurized water it is important to avoid getting water directly or indirectly into the exhaust tube. Water in the exhaust tube will damage sensors and SCR system components and affect the proper operation of the aftertreatment system and the engine.

630E-259

3.40

ENGINE ECU

Tigercat 610E/615E Skidder

Lubrication and Maintenance

The DOC/SCR aftertreatment system consists of the following components: 1. Inlet Humidity Sensor 2. Diesel Exhaust Fluid (DEF) Tank 3. Heater Valve (shown) and Heated DEF Supply Lines (not shown) 4. DENOX 2.2 control system (incorported into the engine electronic control unit) 5. Supply module 6. Exhaust Flap 7. Inlet NOX Sensor

13

8.

9.

10.

11.

12.

13.

DOC Inlet Temperature Sensor Diesel Oxidation Catalyst (DOC) Dosing Module (DEF Injector) Mixer Tube Inlet Temperature Sensor Catalytic Converter / SCR with Clean Up Catalyst (CUC) incorporated 14. Outlet Temperature Sensor 15. NH3 Sensor 16. Outlet NOX Sensor

A 9 11 10

1

6

3

5 2

610E-033

DOC/SCR AFTERTREATMENT SYSTEM COMPONENTS 3.41

Lubrication and Maintenance

Tigercat 610E/615E Skidder HC - HYDROCARBONS NOX - NITROGEN OXIDES CO - CARBON MONOXIDE NH3 - AMMONIA N2 - FREE NITROGEN H2O - WATER CO2 - CARBON DIOXIDE

HUMIDITY SENSOR AIR FILTER

SUPPLY MODULE

EXHAUST FLAP

ECU

HC

NOx SENSOR

NOX CO

DEF QUALITY SENSOR

ENGINE

NOx SENSOR

NH3 SENSOR

N2

DOC

TEMPERATURE SENSORS

HEATER VALVE (CIRCULATING ENGINE COOLANT)

MIXER TUBE CUC

H 2O

DEF LEVEL SENSOR

SCR NH3

CO2

DEF TANK

DOSING MODULE

CATALYTIC CONVERTER

630E-276

DOC/SCR AFTERTREATMENT SYSTEM

The DOC/SCR aftertreatment system is electronically managed by the DeNOX 2.2 system incorporated into the engine electronic control unit (ECU). The ECU calculates and adjusts the flow rate of the DEF solution into the system based on current engine speed, torque delivered, exhaust temperature, amount of nitrogen oxides and ammonia present.

temperature required by the process.

The exhaust fumes and ammonia at the proper reaction temperature, are introduced into the catalytic converter, where the second phase of the process takes place: by reacting with the oxygen in the exhaust gases the ammonia is converted into free nitrogen (N2) and water vapour (H2O).

The exhaust passes through the diesel DOC which uses oxidation at high temperatures to convert carbon monoxide (CO), hydrocarbons (HC) and the soluble organic fraction (SOF) of diesel particulates into inert compounds, carbon dioxide (CO2) and water vapour (H2O). It also converts nitrogen oxide (NO) into nitrogen dioxide (NO2) which enhances the performance of the SCR catalyst.

The supply module pump picks up the DEF solution from the tank and sends it under pressure to the dosing module (DEF injector) to be injected into the exhaust at the outlet of the DOC and pass through the mixer tube upstream of the catalytic converter.

The first phase of the SCR process takes place in the first part of the catalytic converter: high temperature exhaust gas evaporates the DEF solution instantly and, by hydrolysis, converts it into ammonia (2NH3) and carbon dioxide (CO2).

Finally the high efficiency catalytic converter incorporates a clean up catalyst (CUC) which reduces any excess ammonia (NH3) which may result from the SCR process.

IMPORTANT !

Engine should not idle longer than 9 consecutive hours. Damage to the emission control system will result. When this machine idles for an extended period excess hydrocarbon buildup is created in the DOC/SCR aftertreatment system. Burn off of excess hydrocarbon at full load immediately after a long idle period will generate excess heat which will cause damage to emission control system components.

Evaporation of the solution lowers exhaust gas temperature, bringing it closer to the optimum 3.42

Tigercat 610E/615E Skidder HEATER UNIT

Lubrication and Maintenance DEF TANK

DEF TANK 630E-262 DIESEL EXHAUST FLUID (DEF) TANK

DEF QUALITY SENSOR

Diesel exhaust fluid (DEF) is used by the Selective Catalytic Reduction (SCR) aftertreatment system to lower the concentration of nitrogen oxides from the diesel engine exhaust of this vehicle. DEF is an aqueous urea solution with 32.5% high purity urea and 67.5% deionized water. Note that DEF may also be referred to as AUS32 or AdBlue and should meet ISO 22241 specifications. Use only DEF meeting this standard.

It is important to avoid contamination of DEF when filling the tank as this may cause costly damage to SCR system components and affect the proper operation of the SCR system and the engine.

WARNING

The DEF tank is located in the compartment below the right hand cab door. A DEF level indicator is shown on the main menu of the computer display.

The DEF tank includes a fill location, a heater unit and DEF quality sensor. The heater unit incorporates a heater coil, heating system inlet/ outlet connections, DEF inlet/outlet connections, a breather, level sensor, temperature sensor and electrical connector.

COOLANT HEATER COIL

LEVEL SENSOR

TEMPERATURE SENSOR

620E-082

HEATER UNIT

Use only diesel exhaust fluid (DEF) which meets ISO 22241 specifications. NEVER fill the DEF tank with any other fluid.

DEF fluid is injected into the exhaust gas stream during normal operation of the Selective Catalytic Reduction (SCR) aftertreatment system.

Use of other fluids may cause component damage, or a fire risk which could result in death or serious injury.

IMPORTANT! DEF should be stored between -11°C (12°F) and 30°C (86°F) and out of direct sunlight to maximize shelf life and to avoid DEF quality problems caused by improper storage.

When DEF levels are low or a problem with DEF quality is detected information messages will be shown on the computer display. Note that extremely low DEF levels and/or DEF quality problems may result in derating of engine performance to meet emission standard requirements. Action to correct these problems should be taken immediately to avoid affecting engine performance and damage to aftertreatment system components. Refer also to COMPUTER – MESSAGES in SECTION 2 of the OPERATOR'S MANUAL or SECTION 6 of the SERVICE MANUAL. Refer to DRAINING DEF TANK in SECTION 3 of THIS MANUAL. Refer to DEF TANK in SECTION 2 of the OPERATOR'S MANUAL.

DEF QUALITY SENSOR

3.43

Lubrication and Maintenance

Tigercat 610E/615E Skidder Heating is switched OFF when:

CONNECTOR

• DEF tank temperature >16°C (61°F) • Supply module temperature >10°C (50°F) • Ambient air temperature >-4°C (25°F) Heating is switched ON when: • DEF tank temperature <15°C (59°F) • Supply module temperature: +8°C (46°F) • Ambient air temperature: -5°C (23°F)

COOLANT OUTLET

COOLANT INLET 630E-265

When conditions require heating the system will thaw DEF within 30 minutes of engine start for proper operation of the aftertreatment system.

Note also that whenever the engine is stopped all DEF is pumped back to tank before the engine power system is turned off. This process takes approximately 90 seconds.

COOLANT BYPASS

HEATER VALVE

HEATER VALVE / HEATED DEF SUPPLY LINES The heater valve is located on a bracket on the right side of the engine compartment.

RIGHT SIDE OF ENGINE COMPARTMENT

630E-259

ENGINE ECU

DENOX 2.2 DOSING SYSTEM

610E-012

DENOX 2.2 control system is incorporated into the engine electronic control unit (ECU).

HEATER VALVE

The heater valve controls the flow of engine coolant through the DEF tank heater coil and the supply module when heating of the DEF fluid is required. The heater valve also controls the constant flow of engine coolant to the dosing module for cooling purposes. This machine is equipped with electrically heated DEF supply lines.

The DOC/SCR aftertreatment system is electronically managed by the DENOX 2.2 control system. The ECU calculates and adjusts the flow rate of the DEF solution into the system based on current engine speed, torque delivered, exhaust temperature, amount of nitrogen oxides and ammonia present and the humidity levels in incoming air.

DEF freezes at -11°C (12°F).

Temperature sensors signals control the operation of both the electrically heated DEF supply lines and the heater valve which, depending on the temperature, opens or closes the flow of hot engine coolant to the heater coil and supply module.

3.44

Tigercat 610E/615E Skidder

630E-267

SUPPLY MODULE

SUPPLY MODULE The supply module pump picks up the DEF solution from the tank and sends it under pressure to the dosing module, mounted on the mixer tube incorporated into the diesel oxidation catalyst.

DEF is injected into the exhaust at the outlet of the diesel oxidation catalyst and upstream of the catalytic converter.

EXHAUST FLAP

Lubrication and Maintenance

610E-029 DIESEL OXIDATION CATALYST (DOC) DIESEL OXIDATION CATALYST (DOC)

The diesel oxidation catalyst (DOC) uses oxidation at high temperatures to convert carbon monoxide (CO), hydrocarbons (HC) and the soluble organic fraction (SOF) of diesel particulates into inert compounds, carbon dioxide (CO2) and water vapour (H2O).

In addition the DOC converts nitrogen oxide (NO) into nitrogen dioxide (NO2). Increased NO2 levels enhance the performance of the SCR catalyst at low temperatures and increase the effectiveness of the DOC/SCR aftertreatment system as a whole.

The DOC is located upstream of the catalytic converter (SCR & CUC) and at its outlet incorporates the mixer tube and the mounting for the dosing module.

630E-279

EXHAUST FLAP An exhaust flap is located at the exhaust outlet from the engine. The exhaust flap is used to regulate temperature of the exhaust entering the diesel oxidation catalyst (DOC) to optimum levels for proper operation of the aftertreatment system.

3.45

Lubrication and Maintenance

Tigercat 610E/615E Skidder

CATALYTIC CONVERTER

DOSING MODULE DOSING MODULE (DEF INJECTOR) 630E-274

The dosing module is mounted on the DOC outlet upstream of the catalytic converter. The dosing module injects DEF fluid into the exhaust pipe.

Note that this module must be mounted at the correct specified angle to function properly.

The dosing module is cooled by a constant flow of engine coolant supplied by the heater valve to maintain optimum temperature for the aftertreatment process.

610E-030

CATAYTIC CONVERTER

CATALYTIC CONVERTER The catalytic converter is located on the left side of the engine compartment. Chemical reactions inside the catalytic converter reduce nitrogen oxides (NOX) in the exhaust gas.

The catalytic converter is equipped with soundproofing material and replaces the exhaust silencer. It incorporates both the selective catalytic reduction (SCR) and the cleanup catalyst (CUC) components of the aftertreatment system.

The first phase of the SCR process takes part in the first part of the catalytic converter: high temperature exhaust gas evaporates the DEF solution instantly and, by hydrolysis, converts it into ammonia (2NH3) and carbon dioxide (CO2).

630E-275

MIXER TUBE

MIXER TUBE The mixer tube is incorporated into the outlet of the DOC upstream from the catalytic converter.

The insulated high-turbulence mixer tube is used to mix the DEF solution and exhaust gases together before they enter the catalytic converter.

Evaporation of the solution lowers exhaust gas temperature, bringing it closer to the optimum temperature required by the process.

The exhaust fumes and ammonia at the proper reaction temperature, are introduced into the catalytic converter, where the second phase of the process takes place: by reacting with the oxygen in the exhaust gasses the ammonia is converted into free nitrogen (N2) and water vapour (H2O).

Finally the high efficiency catalytic converter incorporates a clean up catalyst (CUC) which reduces any excess ammonia (NH3) which may result from the SCR process.

3.46

Tigercat 610E/615E Skidder

Lubrication and Maintenance ELECTRONIC CONTROL UNIT

SENSOR

630E-264 620E-089

NH3 SENSOR

NH3 SENSOR

HUMIDITY SENSOR

HUMIDITY SENSOR The humidity sensor is located on the air intake just past the air cleaner. This sensor monitors the temperature and humidity of intake air sending signals to the Denox 2.2 control system. This information is used to calculate the amount of DEF fluid to be injected into the system.

TAG

The NH3 sensor is mounted at the outlet of the catalytic converter. The NH3 sensors detect and send information about the NH3 levels in the exhaust. This information is used to calculate the amount of DEF fluid to be injected into the system and to monitor DOC/SCR aftertreatment system operation.

Refer to APPROVED ANTI-SEIZE PASTES FOR EXHAUST / AFTERTREATMENT LINE (TIGERCAT BY FPT Tier 4F ENGINES) in SECTION 3 of THIS MANUAL. ELECTRONIC CONTROL UNIT

CERAMIC SENSOR

620E-087

TEMPERATURE SENSOR

TEMPERATURE SENSORS Temperature sensors are mounted at the inlet of the diesel oxidation catalyst, the inlet of the catalytic converter and the outlet of the catalytic converter. These 3 sensors send exhaust temperature signals to the DENOX 2.2 control system. The control system uses this information to calculate the amount of DEF fluid to be injected into the system.

NOTE: All three temperature sensors are identical, however location should be noted for analysis purposes when replacing a temperature sensor.

620E-088

NOX SENSOR

NOX SENSOR The inlet NOX sensor is mounted upstream of the diesel oxidation catalyst. The outlet NOX sensor is mounted at the outlet of the catalytic converter. The NOX sensors detect and send information about the dosing of DEF solution and the efficiency of the catalytic converter to the Denox 2.2 control system. This information is used to calculate the amount of DEF fluid to be injected into the system and to monitor DOC/SCR aftertreatment system operation.

Each NOX sensor consists of ceramic sensor and an electronic control unit linked by a cable.

The sensor detects the concentration of nitrogen oxides in the exhaust.

3.47

Lubrication and Maintenance The sensor, cable and control unit are considered to be one part for service/replacement purposes.

Note that cable length cannot be changed as this will affect the proper operation of the sensor.

IMPORTANT! When checking or replacing any sensor or plugs in the exhaust or the aftertreatment system it is important to use only approved anti-seize as specified by Tigercat. Use of non-approved compounds can affect the operation of the NOX sensor and cause a malfunction of the DOC/ SCR aftertreatment system. This may result in poisoning of the catalytic converter and require replacement of expensive aftertreatment system parts.

Refer to APPROVED ANTI-SEIZE PASTES FOR EXHAUST / AFTERTREATMENT LINE ( BY FPT Tier 4F ENGINES) in SECTION 3 of THIS MANUAL.

Tigercat 610E/615E Skidder APPROVED ANTI-SEIZE PASTES FOR EXHAUST / AFTERTREATMENT LINE (TIGERCAT BY FPT Tier 4F ENGINES) NOX sensors-Weicon High Tech Anti-Seize only NH3 sensor-Loctite X203 Dry Film Moly Anti-Seize IMPORTANT! When checking or replacing any sensor or plugs in the exhaust or the aftertreatment system it is important to use only approved anti-seize as specified by Tigercat.

Use of non-approved compounds can affect the operation of the NOX and NH3 sensors and cause a malfunction of the aftertreatment system. This may result in poisoning of the SCR catalyst and require replacement of expensive aftertreatment system parts.

3.48

Tigercat 610E/615E Skidder DIESEL EXHAUST FLUID (DEF) HANDLING Diesel exhaust fluid (DEF) is an aqueous urea solution with 32.5% high purity urea and 67.5% deionized water. Note that DEF may also be referred to as AUS32 or AdBlue and should meet ISO 22241 specifications. Use only DEF meeting this standard.

It is important to avoid contamination of DEF as this may cause costly damage to SCR system components and affect the proper operation of the SCR system and the engine.

When a problem with DEF quality is detected information messages will be shown on the computer display. Note that DEF quality problems may result in derating of engine performance to meet emission standard requirements. Action to correct DEF quality problems should be taken imme.diately to avoid affecting engine performance and damage to SCR aftertreatment system components. Refer also to COMPUTER – MESSAGES in SECTION 2 of the OPERATOR'S MANUAL or SECTION 6 of the SERVICE MANUAL. For safety information refer to DIESEL EXHAUST FLUID (DEF) in SECTION 1 of THIS MANUAL.

WARNING Use only diesel exhaust fluid (DEF) which meets ISO 22241 specifications. NEVER fill the DEF tank with any other fluid.

DEF fluid is injected into the exhaust gas stream during normal operation of the Selective Catalytic Reduction (SCR) aftertreatment system.

Use of other fluids may cause component damage, or a fire risk which could result in death or serious injury.

Lubrication and Maintenance AVOID DEF QUALITY PROBLEMS WITH PROPER HANDLING PRACTICES Most DEF quality problems can be avoided entirely with a little care and proper handling of DEF fluid.

FILLING THE DEF TANK •

Always clean the area around the DEF fill cap and avoid introducing contaminants into the DEF tank when filling.

•

Always use only diesel exhaust fluid (DEF) which meets ISO 22241 specifications.

Use of any other fluid will contaminate the aftertreatment system and may pose a safety hazard.

USE OF PROPER STORAGE CONTAINERS •

To prevent contaminants from affecting DEF quality it should be handled only in storage, transport and filling containers intended exclusively for that purpose.

•

Polyethylene or stainless steel containers are recommended. Refer also to DEF manufacturer's recommendations.

•

DEF is corrosive to metals other than stainless steel. Transport in metal containers other than stainless steel will result in contamination.

PROPER STORAGE CONDITIONS TO MAXIMIZE SHELF LIFE •

DEF should be stored between -11°C (12°F) and 30°C (86°F) and out of direct sunlight to maximize shelf life and to avoid DEF quality problems caused by improper storage.

•

DEF quality problems can often be avoided with proper storage and handling practices to maximize shelf life.

•

DEF storage areas should always be out of direct sunlight and away from heat sources to avoid reducing shelf life.

•

DEF shelf life is limited. It should be consumed on a first in first out basis, within manufacturer's recommended shelf life limits.

DEF beyond manufacturer's recommended shelf life limits may not meet ISO 22241 specifications.

3.49

Lubrication and Maintenance CENTRE JOINT

Tigercat 610E/615E Skidder

MAINTENANCE OF CENTRE JOINT Maintenance in this area is usually limited to: a) Regular lubrication of the two centre joint grease fittings to purge the pivot bearings of debris and water. Refer to SERVICE AND LUBRICATION POINTS in THIS SECTION for lubrication intervals. Use only high quality, lithium based EP2 grease containing molybdenum disulphide. b) Visually checking the centre joint pivot for looseness every 48 hours. With an observer on the ground, keeping well clear of the centre joint area, perform the following test to check for looseness of centre joint.

1. Have operator lift the dozer blade off the ground and then rapidly raise and lower blade several times to "bounce" machine.

2. As machine bounces, check for motion between the front and rear chassis frame lugs. Also check for a "clunking" sound at the centre joint area.

3. Movement between front and rear chassis lugs or clunking of the pivot indicates a loose joint and preload must be checked.

Refer SECTION 11 of the SERVICE MANUAL for more information.

REAR CHASSIS FRONT CHASSIS CHECK FOR MOVEMENT IN THIS JOINT AREA

620E-066

CENTRE JOINT PRELOAD CHECK

3.50

Tigercat 610E/615E Skidder ARTICULATION LOCK STRAIGHT LOCKED POSITION

Lubrication and Maintenance ARTICULATION LOCK ARTICULATED LOCKED POSITION

1. Position machine on level ground and steer machine into a straight ahead position.

1. Position machine on level ground and steer machine into a fully articulated position to the right.

2. Lower grapple and dozer blade to the ground, engage parking brake, stop engine and remove ignition key.

ARTICULATION LOCK

2. Lower grapple and dozer blade to the ground, engage parking brake, stop engine and remove ignition key.

ARTICULATION LOCK

REAR CHASSIS REAR CHASSIS RETAINING PINS

620E-002

3. Remove both retaining pins from the articulation lock. Relocate articulation lock between front and rear chassis. Line up holes at each end of articulation lock with holes in chassis’ and secure in place with both retaining pins.

4. After work is completed, relocate articulation lock into storage position on rear chassis and hold in place with retaining pins.

630E-060

RETAINING PINS

ARTICULATION LOCK STORED POSITION 620E-002

ARTICULATION LOCK STORED POSITION

3. Remove both retaining pins from the articulation lock. Relocate articulation lock between front and rear chassis. Line up holes on the articulation lock with holes in chassis’ as shown and secure in place with both retaining pins.

4. After work is completed, relocate articulation lock into storage position on rear chassis and hold in place with retaining pins.

ARTICULATION LOCK IN STRAIGHT LOCKED POSITION

630E-073

3.51

ARTICULATION LOCK IN ARTICULATED LOCKED POSITION

Lubrication and Maintenance GRAPPLE SNUBBER MAINTENANCE

Tigercat 610E/615E Skidder

SNUBBER ASSEMBLY USED ON TIGERCAT GRAPPLES In this model the snubbers are part of the link.

Two separate snubbers provide snubbing action in two directions. There is a grease fitting on each snubber assembly for daily lubrication. Be sure to lubricate all the grapple snubbers on your machine.

Proper lubrication prevents excessive clutch wear.

IMPORTANT !

All service points on snubbers must be greased every shift (8 hours) to ensure a long service life.

ADJUSTING SNUBBER TENSION Each snubber should be adjusted such that: •

It is capable of stopping the grapple within one full swing.

Snubbers that are too loose can allow the grapple to swing violently and cause damage to the grapple and/or other machine components.

•

It is capable of holding the grapple at approximately a 5° angle.

Snubbers that are overtightened can reduce the effect of lubricating grease and cause premature clutch wear.

615C-022

SNUBBER ASSEMBLY

PROCEDURE Tension is adjusted by removing shims from the snubber. Remove only the minimum number of shims required to achieve correct adjustment.

1. Park machine on level ground, install articulation lock bar, lower dozer and grapple to ground, stop engine, engage parking brake and block wheels.

2. Remove one shim at a time to increase snubber friction. One split shim at a time can be removed from each snubber without completely removing the end caps.

Remove 3 bolts on the left side then loosen 3 bolts on the right side of the snubber enough to separate the end cap from the housing to remove the first half of the shim.

Loosely reinstall the 3 bolts on the left side of the snubber then remove the 3 bolts on the right side keeping the end cap separated from the housing enough to remove the other half of the shim.

Reinstall bolts and tighten in a crisscross pattern.

3. Fill snubber with grease until grease comes out the exhaust port.

3.52

Tigercat 610E/615E Skidder

Lubrication and Maintenance

SNUBBER HOUSING

GREASE FILL PORT

SPLINED SHAFT

GREASE EXHAUST PORT

ALIGN TAB ON SHIMS WITH TAB ON END CAP

FRICTION PLATE REACTION PLATE

BELLEVILLE WASHERS

SHIMS O-RING END CAP

630D-011

SNUBBER ASSEMBLY 3.53

Lubrication and Maintenance PRESSURIZED WATER SYSTEM MAINTENANCE (IF EQUIPPED) WATER WATER TANK CONTROL VALVE

SHUT-OFF VALVE IN CLOSED POSITION 620E-004

DOZER BLADE

HOSE STORAGE COMPARTMENT

PRESSURIZED WATER SYSTEM

A water tank is incorporated into the dozer blade and is pressurized to 60 psi (4 bar). A valve controls the flow of water from the tank to a hose located in the hose storage compartment on the dozer blade.

Tigercat 610E/615E Skidder SYSTEM TEST This system should be tested once every month by turning the shut-off valve ON and expelling water from the hose end nozzle. A very forceful discharge of water should be obtained. If the water does not come out with force (with pressure gauge reading 60 psi [4 bar]) the system needs to be PURGED. Refer to PURGING PRESSURIZED WATER SYSTEM in THIS SECTION. After testing, the tank must be refilled and pressurized to 60 psi (4 bar). Refer to the following FILL AND CHARGE procedure. This FILL AND CHARGE procedure should be carried out yearly.

FILL & CHARGE PRESSURIZED WATER SYSTEM 1. Open water shut-off valve and completely discharge all water and compressed air from the tank via the hose end nozzle.

The control valve incorporates an air charge valve, a pressure gauge and a relief valve on the outlet side of the valve. A ball valve is installed on the outlet side of the valve and is used to shut off the water supply to the hose. This shut-off valve should be in the CLOSED position when the system is not in use.

The pressure gauge on the valve should read 60 psi (4 bar) check system pressure daily. The pressurized water system should be drained and refilled every 1000 hours as per the maintenance schedule.

2. Slowly unscrew fill plug two full turns. Any remaining air in the tank will be heard expelling from the special fill plug. Do not remove fill plug until all air has been expelled.

PRESSURE GAUGE

DOZER BLADE FILL PLUG

OUTLET CONNECTION

WATER TANK

AIR CHARGE VALVE

WATER SHUT-OFF VALVE (SHOWN CLOSED) 620E-003

WATER CONTROL VALVE

Refer also to FIRE PREVENTION in SECTION 1 of THIS MANUAL.

620E-010

PRESSURIZED WATER SYSTEM

3. Close water shut-off valve.

4. Fill tank with clean water.

When temperatures below 32°F (0°C) are anticipated, use a 60/40 solution of Nontoxic R. V. Antifreeze or other suitable antifreeze.

Antifreeze solution must meet GM 6038M specifications.

3.54

Tigercat 610E/615E Skidder NOTE: Most Nontoxic R.V. Anti freeze solutions contain corrosion and algae inhibitors, it is therefore suggested that this solution be added to the water on a continual basis regardless of temperature conditions.

5. Install fill plug in tank.

NOTE: This is a special plug designed to withstand pressurization of the water tank.

Do not substitute.

Lubrication and Maintenance PURGING PRESSURIZED WATER SYSTEM Purging should be carried out whenever the flow of water does not forcefully discharge from the end of the hose with the pressure gauge reading 60 psi (4 bar).

1. Open water shut-off valve and completely discharge all water and compressed air from the tank via the hose end nozzle.

6. Pressurize the system to 60 psi (4 bar) as indicated on pressure gauge by connecting an air hose to air charge valve beside the pressure gauge.

7. Open the water shut-off valve.

8. Discharge about 1/2 US gal (2 L) of fluid into an empty antifreeze jug or other suitable container.

There will be significant foaming as the fluid is discharged into the jug. Continue until a very forceful flow is obtained and any contamination that may have been in the tank is flushed from the system.

9. Check fluid in the jug for contamination. If fluid is dirty dispose of it properly.

2. Slowly unscrew fill plug two full turns. Any remaining air in the tank will be heard expelling from the special fill plug. Do not remove fill plug until all air has been expelled.

3. Close the water shut-off valve and add 2 US gal (8 L) of CLEAN water to the tank.

4. Install the fill plug

10. Close the water shut-off valve.

NOTE: This is a special plug designed to withstand pressurization of the water tank.

Do not substitute.

11. Release pressure and fluid from the hose.

12. Pressurize the system to 60 psi (4 bar) as indicated on pressure gauge by connecting an air hose to air charge valve beside the pressure gauge.

13. Return the hose to the hose compartment.

5. Pressurize the system to 60 psi (4 bar) as indicated on pressure gauge by connecting an air hose to air charge valve beside the pressure gauge.

6. Open the shut-off valve and completely discharge all the water in the tank via the hose end nozzle.

7. Discharge all the water into an empty antifreeze jug or other suitable container.

There will be significant foaming as the fluid is discharged into the jug. Continue until a very forceful flow is obtained and any contamination that may have been in the tank is flushed from the system.

8. If a forceful discharge was not achieved, repeat the purging procedure. If a second purging does not work, remove lines and check for an obstruction.

9. After the purging operation, fill and charge the system as described in FILL & CHARGE PRESSURIZED WATER SYSTEM in THIS SECTION. 3.55

Lubrication and Maintenance CHECKING THE AIR CONDITIONING SYSTEM

Tigercat 610E/615E Skidder CAUTION Use compressed air for cleaning only when the machine is cold to avoid the risk of fire caused by debris contacting hot surfaces.

If using compressed air for cleaning, use at 30psi or less.

Always use personal protective equipment to guard against flying debris.

Any service work must be performed by authorized A/C technicians. The system should be charged with R134a refrigerant only. PAG (polyalkeylene glycol) oil should be present in the system and must be used on 'O' rings and fittings during assembly.

A/C SYSTEM TOTAL CAPACITIES R134a REFRIGERANT

PAG OIL (polyalkylene glycol)

1.76 kg (3 lbs 14 oz)

0.25 kg (9.0 oz)

CAUTION Avoid the risk of fire caused by debris accumulating on surfaces that may become hot during machine operation. Always use care when cleaning to ensure that debris removed from one area of the machine does not accumulate on other areas of the machine.

The compressor and charge valves are accessed from the left side engine compartment. The receiver dryer is mounted in the compartment behind the right cab door, on the outside of the cab.

IMPORTANT !

It is recommended that during cold weather when the A/C system is not in use, that it be run for a period of 5 minutes every 2 weeks. This will circulate oil to all components of the A/C system.

Perform following inspection along with 125 HOURS inspection outlined in SCHEDULED MAINTENANCE in THIS SECTION. a. Check re-circulating and fresh air filters in operator's cab. Refer to SECTION 2 of the OPERATOR'S MANUAL.

c. Check for dirt and debris; on the evaporator coil located inside the A/C-heater unit and also the inside of the A/C-heater unit. Clean as required. d. Check and adjust compressor drive belt tension. e. Check all A/C hoses for kinks.* f.

g. Check air temperature exiting vents in cab. h. Listen to compressor and blower motor for abnormal noises.* i.

CHECK A/C CONDENSER CORE

620E-059

Run air conditioning system for 3 - 5 minutes.

CHECK A/C CONDENSER CORE

b. Check the condenser core for dirt and debris.

Clean as required. Refer to CLEANING A/C CONDENSER AND COOLING ASSEMBLY in SECTION 2 of the OPERATOR'S MANUAL. 3.56

Check to see that compressor clutch will engage.*

Tigercat 610E/615E Skidder

Lubrication and Maintenance

SIGHT GLASS INDICATES CONDITION OF CHARGE

MOISTURE INDICATOR BLUE - OK. PINK - REPLACE DRYER, RECHARGE SYSTEM BINARY SWITCH, SYSTEM PROTECTION

A/C RECEIVER/DRYER

620E-012

j.

A/C RECEIVER/DRYER

Inspect sight glass on receiver dryer with A/C ON. A constant stream of bubbles indicates system requires charging.* Check colour in moisture indicator; BLUE is OK. PINK indicates desiccant material in dryer is saturated with moisture. In this situation replace receiver/dryer, evacuate system and recharge system with both refrigerant and PAG oil.* * Indicates that these repairs must only be carried out by a certified A/C technician.

For additional SERVICE information refer to the Tigercat A/C SERVICE MANUAL part number 18795A, available from Tigercat parts department.

3.57

Lubrication and Maintenance TILTING THE CAB WARNING Before tilting the cab, ensure that the machine is parked on level ground. Lower the dozer blade and grapple on to the ground.

Engage the parking brake and turn the ignition switch off.

NOTE: The cab tilt circuit is closed and does not normally require scheduled maintenance other than lubrication of cylinders and pivot points.

Tigercat recommends the use of DEXTRON III TYPE transmission fluid in this circuit (total circuit capacity 1 L [0.25 US gal]). The fill port is located on the pump.

Tigercat 610E/615E Skidder RAISING THE CAB 1. Position the Skidder on level ground.

2. Lower the Grapple and Dozer to the ground.

3. Engage parking brake and turn ignition off.

4. Remove the sweep mounting bolts at the cab.

(2 bolts) 5. Remove the right side Cab Locking Pins (2 pins). This is done by first removing the locking bolts. (2 bolts) 6. Open the maintenance door on the right front access panel to access the cab tilt hand pump.

LOCATED IN THE RIGHT HAND STEP COMPARTMENT BELOW THE CAB DOOR PUMP LEVER SHOWN IN "RAISE" POSITION

CAB SWEEP BOLTS PUMP

PUMP HANDLE 620E-065

610E-014

PUMP CONTROL LEVER IN RAISE CAB POSITION

7. Turn the lever on the pump manifold to RAISE (pointing to the front of the machine).

8. Insert handle into pump and pump in a steady manner to raise the cab to the tilt position.

The pump handle is stored in brackets inside the cab.

CAUTION 620E-070

620E-067

620E-017

CAB LOCKING PINS

PUMP HANDLE STORAGE

Keep hands away from the locking pin area.

As the cab passes "top dead centre" it will slowly move on its own to the full extent of the safety cable. DO NOT PUMP BEYOND LIMIT OF SAFETY CABLE.

9. Insert CAB SUPPORT BRACE for partial tilt.

Secure brace at each end with the cab locking pins. Full tilt is limited to the length of the safety cable and is beyond centre of gravity.

The cab will stay at this limit provided Skidder is on level ground.

3.58

Tigercat 610E/615E Skidder WARNING

Before working under cab;

Machine must be parked on level ground.

Cab must be fully tilted with safety cable completely tight, or cab support brace must be installed.

Lubrication and Maintenance LOWERING THE CAB 1. Clear the area under the cab of obstructions and secure all lines and wires.

2. If the Cab Support Brace was used, you may have to take the weight off of it by slightly raising the cab before removing it.

LOCATED IN THE RIGHT HAND STEP COMPARTMENT BELOW THE CAB DOOR PUMP HANDLE PUMP LEVER SHOWN IN "LOWER" POSITION

PUMP

610E-013

CAB SAFETY CABLE (3361B)

PUMP CONTROL LEVER IN LOWER CAB POSITION

3. Turn the lever on the pump manifold to LOWER (pointing to the rear of the machine)

CAUTION

610E-015

CAB AT FULL TILT SUPPORTED

BY SAFETY CABLE CAB LOCKING PIN

SAFETY CABLE

CAB SUPPORT BRACE (3291B).

MUST USE CAB & CHASSIS LUGS SHOWN CAB LOCKING PIN

620E-064

PARTIAL TILT WITH CAB SUPPORT BRACE

Keep hands away from the locking pin area as the cab is being lowered.

4. Pump the handle in a steady motion to lower the cab.

5. Watch closely for pinching of hydraulic lines and wires.

6. When fully lowered, insert Cab Locking Pins and tighten locking bolts (2 pins) (2 bolts) 7. Turn the lever on the pump manifold to point toward the front of the machine and store the pump handle inside the cab.

8. Close the maintenance door securely.

9. Replace the Cab Sweep Bolts. (2 bolts)

WARNING

CAB SUPPORT BRACE

If cab support brace is damaged or lost, it must be replaced immediately with Tigercat brace PART NO. 3291B. DO NOT attempt to work under a raised cab supported only by the hydraulic cylinder or a substitute device.

WARNING 610E-005

If cab safety cable is damaged or lost, it must be replaced immediately with Tigercat PART NO. 3361B. DO NOT attempt to work under a raised cab supported only by the hydraulic cylinder or a substitute device.

CAB SUPPORT BRACE STORED IN COMPARTMENT BELOW RIGHT HAND CAB DOOR

3.59

Lubrication and Maintenance WINCH MAINTENANCE - ALLIED

Tigercat 610E/615E Skidder LUBRICATION

WINCH OPERATION The winch is driven by a hydraulic motor through the sprag clutch and winch drive components. The pinion sprag holds the load in conjunction with the free spool clutch to prevent reverse rotation of the drum. The free spool clutch separates the drum from other drive components and permits the cable to unwind freely.

The winch is controlled through the winch select switch and the winch control lever. The winch select switch is used to activate/deactivate the winch control lever and to activate the winch freespool function. The winch control lever when activate is used to wind in the winch. Refer to CAB CONTROLS – WINCH CONTROL LEVER , CAB CONTROLS – WINCH SELECT SWITCH in SECTION 2 of the OPERATOR'S MANUAL.

Refer to the manufacturer's maintenance and service manual for information on your winch.

The sump holds 1.0 US gal (3.8 L).

The oil supplied is Esso Hydraul 56 (Summer) or Esso Hydraul 50 (Winter). Use these oils or the equivalent.

Oil should be changed every 1000 hrs, depending on use.

The oil level should be checked every day (if the winch is being used) before starting the machine.

AIR BREATHER/FILL CAP

Refer also to OPERATING MACHINE – OPERATING WINCH and SKIDDING – CABLE SKIDDING in SECTION 2 of the OPERATOR'S MANUAL. Refer to SECTION 13 of the SERVICE MANUAL and the winch manufacturer's service manual for additional service information.

WINCH SPECIFICATIONS ALLIED WINCH MODEL W400

610C-41

WINCH LUBRICATION

Maximum rated line pull bare drum ............................40000 lbs (18180 kg) full drum................................28100 lbs (12745 kg)

OIL LEVEL PLUG

Maximum cable size.............1 in (25.4 mm) 610C-42

Drum Size and Capacities Barrel Diameter....................12.0 in (305 mm) Barrel Width..........................7.79 in (200 mm) Cable Capacity 3/4 in (19.1 mm) ..................215 ft (65.5 m) 7/8 in (22.2 mm) ..................160 ft (48.8 m) 1 in (25.4 mm) .....................92 ft (28 m)

The oil level should be up to the oil level check plug (remove with allen wrench) on the left side of the winch. Keep the winch sump filled to the correct level by adding oil through the air breather check valve assembly on the left side of the winch.

Winch Ratio Model W410.....21.65:1 Dry Weight ...........................1150 lbs (520 kg) Oil supply maximum pressure...............................3045 psi (210 bar) Oil supply maximum flow......47 USgpm(178 L/min)

3.60

Tigercat 610E/615E Skidder

Lubrication and Maintenance

MAINTENANCE

CABLE RETAINER PLATE

Maintenance of the winch is limited to the hydraulic system maintenance of the skidder itself.

CABLE GROOVE

Periodically check the winch, control valve, and connecting hoses for damage or hydraulic oil leakage. If any problems are found, they should be corrected before operating the winch.

LOCKSCREW

INSTALLING THE WINCH MAINLINE 610C-40

ADJUST THE WINCH FREESPOOL TENSION

INSTALLING THE WINCH MAINLINE

WARNING

ADJUST THE WINCH FREE-SPOOL TENSION If the winch cable requires too little effort to pull it from the cable drum, the tension can be adjusted as follows:

Use extreme care when removing cable and ferrule from the drum. When the ferrule is released the cable may spring out with force.

•

Loosen the lockscrew.

•

Tighten the adjusting nut to increase the tension and/or loosen it to decrease it.

•

Tighten the locknut.

Installing the winch mainline as follows will provide a safety break-away feature. If the load should fall down a hillside, the operator should IMMEDIATELY put the winch control in FREESPOOL position. This will allow the cable to unwind freely from the cable drum and break away from the winch, preventing the machine from being pulled over.

•

Start the engine and rotate the winch cable drum so that the cable and ferrule groove in the inside, left hand wall of the drum is at the top and turn off the engine.

•

Remove the cable retainer plate capscrews and retainer plate from the cable drum.

•

Insert the cable ferrule into the groove in the drum and hold the cable against the drum.

•

Install the retaining plate and capscrews to hold the cable in place.

•

Start the engine and winch in the cable onto the drum.

3.61

Lubrication and Maintenance WINCH MAINTENANCE - CARCO WINCH OPERATION The winch is controlled through the winch select switch and the winch control lever. The winch select switch is used to activate/deactivate the winch control lever and to activate the winch freespool function. The winch control lever when activate is used to wind in the winch.

The Carco winch functions differently than other winches operators may be familiar with. The following are notes for Carco winch operators to remember: •

Do not use freespool (mechanical jaw clutch) to drop a suspended load or if there is tension on the cable

•

Use drive away (dynamic brake clutch) to lower a load, drive away from a load, to release tension in a cable.

•

After using freespool or drive away allow the clutches to fully re-engage before winching in. This is especially important when the oil is cold.

•

Use freespool only when pulling cable off the winch by hand

•

Both drive away and freespool clutches are spring applied hydraulic release

•

Read the operator's manual for complete winch operating instructions.

Refer to CAB CONTROLS – WINCH CONTROL LEVER , CAB CONTROLS – WINCH SELECT SWITCH in SECTION 2 of the OPERATOR'S MANUAL. Refer also to OPERATING MACHINE – OPERATING WINCH and SKIDDING – CABLE SKIDDING in SECTION 2 of the OPERATOR'S MANUAL. Refer to SECTION 13 of the SERVICE MANUAL and the winch manufacturer's service manual for additional service information.

Tigercat 610E/615E Skidder WINCH SPECIFICATIONS CARCO STANDARD (GEAR MOTOR) Maximum rated line pull bare drum ............................40000 lbs (18180 kg) full drum................................21700 lbs (9840 kg) Maximum cable size.............1 in (25.4 mm) Drum Size and Capacities Barrel Diameter.................... 9.0 in (228 mm) Barrel Width.......................... 8.31 in (211 mm) Cable Capacity 3/4 in (19.1 mm) ..................275 ft (83.8 m) 7/8 in (22.2 mm) ..................202 ft (61.6 m) 1 in (25mm)..........................169 ft (51 m) Winch Ratio..........................118.65:1 Dry Weight ...........................1430 lbs (649 kg) Maximum pressure to motor................................3300 psi (228 bar) Maximum flow to motor........46 USgpm(176 L/min) WINCH SPECIFICATIONS CARCO HIGH SPEED (PISTON MOTOR) Maximum rated line pull bare drum ............................40000 lbs (18180 kg) full drum................................24000 lbs (10890 kg) Maximum cable size.............1 in (25.4 mm) Drum Size and Capacities Barrel Diameter.................... 9.0 in (228 mm) Barrel Width.......................... 8.31 in (211 mm) Cable Capacity 3/4 in (19.1 mm) ..................275 ft (83.8 m) 7/8 in (22.2 mm) ..................202 ft (61.6 m) 1 in (25mm)..........................169 ft (51 m) Winch Ratio..........................66.98:1 Dry Weight ...........................1475 lbs (669 kg) Maximum pressure to motor................................4500 psi (310 bar) Maximum flow to motor........46 USgpm(176 L/min)

3.62

Tigercat 610E/615E Skidder

Lubrication and Maintenance

LUBRICATION OIL FILL PLUG

Refer to the manufacturer's maintenance and service manual for information on your winch.

The sump holds approximately 3 US gal (12 L).

The oil supplied is DEXTRON III TYPE transmission fluid. Use this or the equivalent.

OIL LEVEL SIGHT GAUGE

Oil should be changed every 1000 hrs, depending on use.

WINCH FREESPOOL

DYNAMIC BRAKE CLUTCH

The oil level should be checked every day (if the winch is being used) before starting the machine.

The oil level should be up to the centre of oil level sight gauge on the left side of the winch. Check oil when the oil is cool and has been allowed to settle after use. The oil fill plug is on the top of the winch.

DRAIN PLUG

WARNING Failure to use the recommended type and viscosity of planetary gear oil for operating conditions, particulary in cold weather conditions, may contribute to intermittent brake clutch slippage which could result in death or serious injury.

WINCH LUBRICATION

620E-079

SPRING HOUSING

JAM NUT

Failure to properly warm up the winch, particulary in cold weather conditions, may result in temporary brake clutch slippage which could result in death or serious injury.

WINCH MAINTENANCE Maintenance of the winch is limited to the hydraulic system maintenance of the skidder itself.

Periodically check the winch, control valve, and connecting hoses for damage or hydraulic oil leakage. If any problems are found, they should be corrected before operating the winch.

ADJUST THE WINCH FREE-SPOOL TENSION If the winch cable requires too little effort to pull it from the cable drum, the tension can be adjusted as follows: •

Loosen the jam nut.

•

Tighten the spring housing to increase the tension and/or loosen it to decrease it.

•

Tighten the jam nut.

Refer to the manufacturer's maintenance and service manual for information on your winch.

3.63

620E-078

ADJUST THE WINCH FREESPOOL TENSION

Lubrication and Maintenance START-UP PROCEDURE AFTER MAJOR MACHINE MAINTENANCE

Tigercat 610E/615E Skidder •

Prepare the fill pump on the machine to add hydraulic oil. Clean the fill line pipe, remove cap on end of pipe and insert pipe into oil supply drum.

•

Loosen the plug on the top of the left hand drive motor.

•

Operate the fill pump.

•

Watch for oil leaking from the plug previously loosened and tighten plug when oil leaks out.

•

Continue pumping slowly and watch the oil sight gauge on the tank. Continue pumping slowly until the hydraulic tank is full.

This procedure should be followed: •

after major service or a rebuild.

•

whenever the machine has been drained of hydraulic oil.

•

when any major component has been removed, repaired or replaced.

PRESTART-UP AND FILLING 1. Ensure all filters are in place. Refer to FILTERS in THIS SECTION. 2. Check oil levels in the engine, transmission, main hydraulic tank, winch (if equipped), axles and cab tilt system.

3. Check coolant level in the radiator.

MACHINE START-UP Before beginning this procedure, perform the PRESTART-UP AND FILLING steps.

CAUTION

4. Do a final inspection of all fittings and clamps to make sure they are tight and will not leak.

5. Install the articulation lock bar and engage the parking brake.

6. Turn differential lock switch to OFF.

Machine operator must ONLY take directions from the person doing the set-up.

1. Ensure the articulation lock bar is installed.

7. Do not start engine. Purge air from hydraulic system by adding oil as follows: •

DISCONNECT THE TOP PLUG FROM THE ENGINE ECU

Pre-fill the cases of the hydrostatic drive pump, main pump and any other components that have been drained of oil with clean, filtered hydraulic oil.

CASE DRAIN MAKE-UP LINE

TEE CONNECTOR

610E-021

630E-297

2. Disconnect the top plug from engine ECU (prevents engine starting).

RIGHT HAND DRIVE MOTOR DISCONNECT CASE DRAIN LINE

•

Disconnect the case drain make-up line from the tee connection on the right hand drive motor and pre-fill the right hand drive motor with clean, filtered hydraulic oil.

•

Watch for oil leaking from tee connection and reconnect case drain line when oil leaks out.

ENGINE ECU DISCONNECT - LEFT SIDE

3.64

Tigercat 610E/615E Skidder

Lubrication and Maintenance

3. Crank engine for 10 seconds, wait for 10 seconds. Repeat 6 times to pump oil into pumps.

4. Check hydraulic oil levels in the main hydraulic tank and add hydraulic oil as required.

5. Reconnect 4 pin engine power connector or injectors on engine as applicable.

NOTE: If the machine was on wheels, the steer and drive functions were not properly purged or flushed. Remove the articulation lock bar and at LOW IDLE, slowly operate the steer function right and left a few times. With the parking brake disengaged and at LOW IDLE, slowly operate the drive function forward and reverse a few times.

NOTE: If possible, allow the machine to stand for 4 to 6 hours before setting any of the operating pressures. This will allow any air bubbles in the oil to escape and is a good time to check for leaks.

6. Start engine.

7. Check for leaks.

DRIVE PUMP

CONNECTORS

610E-020

DISCONNECT TWO CONNECTORS ON DRIVE PUMP PRIOR TO PERFORMING PROCEDURE

8. Bleed brakes (front axle) if required.

Prior to bleeding brakes disconnect the two connectors on the drive pump. This is a safety precaution to prevent the machine from travelling while brake bleeding is being performed.

With engine at IDLE, parking brake engaged, hold foot brake down, bleed brakes in front axle (both sides). Refer also to FRONT AXLES – SERVICE BRAKES – BRAKE BLEEDING in SECTION 8 of the SERVICE MANUAL. Reconnect two connectors on drive pump.

9. Set throttle to IDLE and run each function for 2 minutes to purge air from circuit.

10. Set throttle to FULL and run each function again for 2 minutes to flush circuit.

11. Top up the radiator with clean coolant.

12. With cylinders fully retracted, top up the main hydraulic oil tank with clean hydraulic oil.

3.65

Lubrication and Maintenance AXLE LEVEL CHECK, FILL AND DRAIN LOCATIONS

Tigercat 610E/615E Skidder FRONT AXLE - LIMITED SLIP ADDITIVES Front axles are equipped with brakes. It is permissible to use a limited slip additive in the front axle to reduce brake chatter noise. Do not exceed the maximum recommended amount of additive as this may cause a loss of differential lock slipping torque and brake holding torque.

Refer to LUBRICATION AND SERVICE CHART for additive recommendation details.

Refer to LUBRICATION AND SERVICE CHART and SCHEDULED MAINTENANCE in THIS SECTION for service intervals and recommended gear oils.

NOTE: Warranty coverage of powertrain components is contingent on performance of regular oil sampling at the owner’s expense during the warranty period. Refer to OIL ANALYSIS PROGRAM in THIS SECTION for details.

Refer also to AXLE – REAR (BOGIE) AXLE for 615E machines.

AXLE LEVEL CHECK AND FILL

PINION SEAL GREASE FITTING

AXLE LEVEL CHECK AND FILL (FAR SIDE)

AXLE DRAIN 4658D02

STANDARD DUTY AXLE DRAIN AND FILL LOCATIONS (FRONT AXLE SHOWN 610E)

PINION SEAL GREASE FITTING

AXLE LEVEL CHECK AND FILL (FAR SIDE)

AXLE LEVEL CHECK AND FILL

AXLE DRAIN 4326D03

STANDARD DUTY AXLE DRAIN AND FILL LOCATIONS (REAR AXLE SHOWN 610E) 3.66

Tigercat 610E/615E Skidder

Lubrication and Maintenance

CAUTION

PINION SEAL GREASE FITTING

Fluid spray hazard. Contact with fluid under pressure may cause injury.

Pressure may build up inside axle due to temperature changes. Use caution when removing drain and fill plugs, slowly loosen plug to relieve pressure before removing completely.

615E-001

PINION SEAL GREASE FITTING

PINION SEAL GREASE FITTING

AXLE LEVEL CHECK AND FILL

AXLE LEVEL CHECK AND FILL (FAR SIDE)

AXLE DRAIN 4326D

STANDARD DUTY AXLE DRAIN AND FILL LOCATIONS (FRONT AXLE 615E)

AXLE LEVEL CHECK AND FILL (FAR SIDE)

BRAKE INSPECTION PORT (FAR SIDE)

BRAKE INSPECTION PORT

AXLE LEVEL CHECK AND FILL

PINION SEAL GREASE FITTING

AXLE DRAIN 4521D15

SEVERE DUTY AXLE DRAIN AND FILL LOCATIONS (FRONT AXLE 615E) 3.67

Lubrication and Maintenance REAR (BOGIE) AXLE (IF EQUIPPED) The bogie axle oil reservoirs (differential, bogie housings and planetaries) are all connected and can be accessed at 2 locations to get the proper level of lubrication in the bogie axle.

Refer to SERVICE AND LUBRICATION POINTS CHART in SECTION 3 for differential oil capacity and recommended gear oils.

DRAINING AND REFILLING BOGIE AXLE •

Park the machine on level ground.

•

Stop the engine and engage parking brake.

•

The bogie axle must be level in order to drain and refill it properly.

•

The oil must be warm before draining and refilling.

•

Clean around all fill, level and drain plugs before removing them.

Tigercat 610E/615E Skidder BOGIE AXLE FILL (2 FILLING POINTS) 1. Note that the bogie housings must be level to drain and refill them properly.

2. Before draining the oil from the bogie housings, the axle should sit for at least 30 minutes so that contaminants in the oil can settle in the oil pan.

3. Remove the the BOGIE HOUSINGS FILL/ LEVEL PLUGS (1 per housing).

4. Remove the BOGIE HOUSING DRAIN PLUGS (2 per housing) and drain the oil into a suitable container for disposal.

5. Remove the DIFFERENTIAL DRAIN PLUG and drain the oil into a suitable container for disposal.

6. Clean any filings from the five drain plugs.

7. Replace the DIFFERENTIAL DRAIN PLUG and the BOGIE HOUSING DRAIN PLUGS (2 per housing) 8. Refill the differential and bogie housings with new oil until the level reaches the bottom of the FILL/LEVEL PLUGS. Refer to SERVICE AND LUBRICATION POINTS CHART in SECTION 3 for differential oil capacity and recommended gear oils.

9. Replace the BOGIE HOUSINGS FILL/LEVEL PLUGS. 10. Check all drain, fill and level plugs for leaks.

11. Run axle for at least 10 minutes to remove trapped air in confined spaces.

12. Recheck oil level and top up as necessary.

BRAKE INSPECTION PORT (2 PLACES)

BOGIE HOUSING DRAIN PLUG (4 PLACES ) 52746B

BOGIE HOUSINGS FILL/LEVEL PLUG (2 PLACES)

DIFFERENTIAL DRAIN PLUG (1 PLACE) BOTTOM OF DIFFERENTIAL NOT VISIBLE IN THIS ILLUSTRATION

BOGIE AXLE FILL, DRAIN AND LEVEL PLUGS (STANDARD DUTY AXLE SHOWN) 3.68

Tigercat 610E/615E Skidder SLEW BEARING LUBRICATION BOGIE AXLES

Lubrication and Maintenance

The slew bearing requires regular lubrication.

Refer to SERVICE AND LUBRICATION POINTS ~MACHINES 6151000 TO 6151500 and SCHEDULED MAINTENANCE in THIS SECTION for maintenance interval and lubrication point information.

3.69

Lubrication and Maintenance

Tigercat 610E/615E Skidder

TORQUE CHART LOCATION

DIAMETER

Cylinders Piston nut, steer cylinder (38087B) Piston nut, arch/boom cylinder Piston nut, dozer cylinder Gland, steer cylinder (36597B) Keeper plate bolts Keeper plate bolts

1 3/8" UNF 1 1/2" UNF 1 3/8" UNF 3/4" UNC 5/8" UNC

1260 1640 1260 550 282 159

1708 2224 1708 745 382 215

Cab pin keeper plate bolts

3/4" UNC

282

393

Centre joint bearing Bearing retaining bolts Pin retaining bolts

1/2" UNC 3/4" UNC

80 282

108 382

Engine mounting To Chassis To Engine

7/8" UNC M12

364 73

493 99

Pump Mounting Drive pump to flywheel adapter plate Flywheel adapter plate to flywheel housing Torsional drive coupler to flywheel Main pump to drive pump Coolant pump to main pump

3/4" UNC M10 3/8" UNC 5/8" UNC M12

282 40 37 159 73

382 54 50 215 99

1 1/4" x 18 UNEF 3/4" UNC

500 282

677 382

1/2" UNF

90

122

M12

70

95

1/2" UNF

90

122

1/2" UNF

90

122

M12

70

95

Axle mounting bolts Front Axle Rear Axle 610E Rear (Bogie) Axle 615E

3/4" UNC 7/8" UNC M30

226 364 1350

306 493 1850

Wheel bolts

7/8" UNF

501

679

Transmission Housing to Mounting Bracket Mounting Bracket to Frame

5/8"UNC 7/8" UNC

159 364

215 493

Drive shafts Yoke retaining nut, rear shaft Pillow block retaining bolts Rear drive shaft universal joint bolts Rear axle input universal joint bolts Mid. drive shaft universal joint bolts Front drive shaft universal joint bolts Front axle input universal joint bolts

TORQUE (LUBRICATED) lbf-ft Nm

Torque values pertaining to the engine and attachment are provided in the appropriate manuals.

610E615EETORQUECHARTR0.XLS 12/14

3.70

Tigercat 610E/615E Skidder

Lubrication and Maintenance

GENERAL TORQUE SPECIFICATIONS The torque values listed below are for general use only.

DO NOT use these values if a different torque value or tightening procedure is shown for a specific application.

IMPERIAL GRADE 8 BOLTS

GRADE 5 BOLTS

IMPERIAL BOLT TORQUE SPECIFICATIONS GRADE 8 BOLTS GRADE 5 BOLTS COARSE THREAD 1/4" - 20 5/16" - 18 3/8" - 16 7/16" - 14 1/2" - 13 9/16" - 12 5/8" - 11 3/4" - 10 7/8" - 9 1" - 8 1 1/8" - 7 1 1/4" - 7 FINE THREAD 1/4" - 28 5/16" - 24 3/8" - 24 7/16" - 20 1/2" - 20 9/16" - 18 5/8" - 18 3/4" - 16 7/8" - 14 1" - 14 1 1/8" - 12 1 1/4" - 12

DRY lbf-ft Nm 11 - 12 15 - 16 26 - 30 35 - 40 44 -48 60 - 65 70 - 77 95 - 104 106 - 117 144 - 158 153 - 168 208 - 228 212 - 233 288 - 316 376 - 414 510 - 561 606 - 667 822 - 904 909 - 1000 1233 - 1355 1288 - 1417 1746 - 1921 1817 - 1999 2464 - 2710 DRY lbf-ft Nm 13 - 14 18 - 19 23 - 28 31 - 38 49 - 54 67 - 73 78 - 86 106 - 116 120 - 132 163 - 179 171 - 188 232 - 255 240 - 264 326 - 358 420 - 462 570 - 626 668 - 735 906 - 996 995 - 1096 1359 - 1486 1445 - 1590 1960 - 2155 2012 - 2213 2728 - 2997

LUBRICATED lbf-ft Nm 8 - 10 11 - 13 20 - 28 27 - 38 33 - 36 45 - 49 52 - 57 71 - 77 80 - 88 109 - 119 115 - 127 156 - 172 159 - 175 216 - 237 282 - 310 393 - 420 455 - 501 617 - 679 682 - 750 925 - 1016 966 - 1062 1310 - 1441 1360 - 1496 1844 - 2027 LUBRICATED lbf-ft Nm 10 - 13 14 - 17 18 - 25 25 - 33 37 - 41 50 - 55 58 - 64 79 - 86 90 - 99 122 - 134 128 - 141 174 - 191 180 - 198 244 - 268 315 - 347 427 - 470 501 - 550 679 - 745 746 - 821 1012 - 1113 1083 - 1191 1469 - 1613 1509 - 1660 2046 - 2250

DRY LUBRICATED COARSE THREAD lbf-ft Nm lbf-ft Nm 1/4" - 20 7- 8 10 - 11 8 - 10 11 - 13 5/16" - 18 14 - 18 19 - 24 10 - 15 13 - 20 3/8" - 16 31 - 34 42 - 46 23 - 25 31 - 34 7/16" - 14 49 - 54 66 - 73 37 - 41 50 - 55 1/2" - 13 75 - 83 102 - 112 57 - 63 77 - 85 9/16" - 12 109 - 120 148 - 162 82 - 90 111 - 122 5/8" - 11 150 - 165 204 - 223 113 - 124 152 - 168 3/4" - 10 266 - 293 360 - 397 200 - 220 271 - 298 7/8" - 9 394 - 433 535 - 586 296 - 326 402 - 441 1" - 8 591 - 649 802 - 879 443 - 489 601 - 663 1 1/8" - 7 794 - 873 1077 - 1183 596 - 656 808 - 889 1 1/4" - 7 1120 - 1232 1519 - 1670 840 - 924 1139 - 1252 FINE DRY LUBRICATED lbf-ft Nm lbf-ft Nm THREAD 1/4" - 28 9 - 10 12 - 13 9 - 10 12 - 13 5/16" - 24 17 - 22 23 - 29 16 - 20 21 - 27 3/8" - 24 35 - 39 48 - 53 26 - 29 35 - 39 7/16" - 20 55 - 61 75 - 83 41 - 45 56 - 61 1/2" - 20 85 - 94 116 - 127 64 - 70 87 - 95 9/16" - 18 121 - 133 164 - 180 91 - 100 124 - 135 5/8" - 18 170 - 187 231 - 253 128 - 141 174 - 191 3/4" - 16 297 - 327 403 - 443 223 - 245 303 - 332 7/8" - 14 434 - 477 589 - 646 326 - 359 442 - 486 1" - 12 646 - 711 876 - 965 484 - 534 657 - 724 1 1/8" - 12 891 - 980 1208 - 1328 668 - 735 906 - 996 1 1/4" - 12 1240 - 1364 1682 - 1849 931 - 1024 1262 - 1387

METRIC

SIZE

CLASS 4.8 DRY LUBRICATED Nm lbf-ft Nm lbf-ft

METRIC BOLT TORQUE SPECIFICATIONS

CLASS 8.8 OR 9.9 LUBRICATED DRY Nm lbf-ft Nm lbf-ft

CLASS 10.9 DRY LUBRICATED Nm lbf-ft Nm lbf-ft

CLASS 12.9 LUBRICATED DRY Nm lbf-ft Nm lbf-ft

M6 M8 M10

4.8 12.0 23.0

3.5 8.5 17.0

6.0 15.0 29.0

4.5 11.0 21.0

9.0 22.0 43.0

6.5 16.0 32.0

11.0 28.0 55.0

8.5 20.0 40.0

13.0 32.0 63.0

9.5 24.0 47.0

17.0 40.0 80.0

12.0 30.0 60.0

15.0 37.0 75.0

11.5 28.0 55.0

19.0 47.0 95.0

14.5 35.0 70.0

M12 M14 M16

40.0 63.0 100.0

29.0 47.0 73.0

50.0 80.0 125.0

37.0 60.0 92.0

75.0 120.0 190.0

55.0 88.0 140.0

95.0 150.0 240.0

70.0 110.0 175.0

110.0 175.0 275.0

80.0 130.0 200.0

140.0 225.0 350.0

105.0 165.0 225.0

130.0 205.0 320.0

95.0 150.0 240.0

165.0 260.0 400.0

120.0 190.0 300.0

M18 M20 M22

135.0 190.0 260.0

100.0 140.0 190.0

175.0 240.0 330.0

125.0 180.0 250.0

260.0 375.0 510.0

195.0 275.0 375.0

330.0 475.0 650.0

250.0 350.0 475.0

375.0 530.0 725.0

275.0 400.0 540.0

475.0 675.0 925.0

350.0 500.0 675.0

440.0 625.0 850.0

325.0 560.0 460.0 800.0 625.0 1,075.0

410.0 580.0 800.0

M24 M27 M30

330.0 490.0 675.0

250.0 360.0 490.0

425.0 625.0 850.0

310.0 650.0 450.0 950.0 625.0 1,300.0

M33 900.0 M36 1,150.0

475.0 825.0 600.0 925.0 675.0 1,150.0 850.0 1,075.0 800.0 1,350.0 1,000.0 700.0 1,200.0 875.0 1,350.0 1,000.0 1,700.0 1,250.0 1,600.0 1,150.0 2,000.0 1,500.0 950.0 1,650.0 1,200.0 1,850.0 1,350.0 2,300.0 1,700.0 2,150.0 1,600.0 2,700.0 2,000.0

675.0 1,150.0 850.0 1,750.0 1,300.0 2,200.0 1,650.0 2,500.0 1,850.0 3,150.0 2,350.0 2,900.0 2,150.0 3,700.0 2,750.0 850.0 1,450.0 1,075.0 2,250.0 1,650.0 2,850.0 2,100.0 3,200.0 2,350.0 4,050.0 3,000.0 3,750.0 2,750.0 4,750.0 3,500.0

3.71

Lubrication and Maintenance

Tigercat 610E/615E Skidder

Parker

Assembly Torque The four-bolt port is simply a circular opening (flow passage) surrounded by four tapped holes in a certain pattern for acceptance of the flange clamping bolts. The flat surface of the port compresses the O-ring contained in the groove in the flange head when the clamp bolts are torqued. In some instances, the groove is in the port and not in the flange head. The bolts, through the clamp halves, clamp down the flange head on to the flat surface of the port compressing and trapping the O-ring in the groove and leaving no gap for it to extrude under pressure. The hydraulic pressure is thus sealed by the compressed O-ring as long as the bolts are tightened enough to maintain solid metal to metal contact between the flange head at the outside diameter of the O-ring and the top of the port.

The 4-Bolt Split Flange consists of four main components: • A body (flange head) • An O-ring • One “captive” or two “split” flange clamps

• Four bolts and washer

WASHERS BOLTS FLANGE CLAMP

Flange Port Assembly

FLANGE HEAD

The steps to properly assemble the flange port clamping bolts are: 1. Make sure sealing surfaces are free of burrs, nicks, scratches or any foreign particles.

2. Lubricate the O-ring.

3. Position flange and clamp halves.

4. Place lock washers on bolts and insert through clamp halves.

5. Hand tighten bolts.

6. Torque bolts in diagonal sequence (see Fig. T9) in small increments to the appropriate torque level listed in Table T6 or Table T7 on this page.

O-RING TAPPED HOLES

FLANGE.JPG

Fig. T8 - 4 Bolt Split Flange Components

FLANGE2.JPG

Fig. T9 - Flange Bolt Tightening Sequence

Dash Size

Flange Size

Inch Bolt (J518)

Torque lbf-ft

Metric Bolt (ISO 6162)

Torque N-m

Dash Size

Flange Size

Inch Bolt (J518)

Torque lbf-ft

Metric Bolt (ISO 6162)

Torque N-m

8 12 16 20 24 32 40 48 56 64 80

1/2 3/4 1 1-1/4 1-1/2 2 2-1/2 3 3-1/2 4 5

5/16-18 3/8-16 3/8-16 7/16-14 1/2-13 1/2-13 1/2-13 5/8-11 5/8-11 5/8-11 5/8-11

17 +/- 2 25 +/- 3.5 31 +/- 4.5 41 +/- 5 52 +/- 6 60 +/- 6 85 +/- 9 144 +/- 15 125 +/- 8 125 +/- 8 125 +/- 8

M8 M10 M10 M12 M12 M12 M12 M16 M16 M16 M16

25 49 49 85 85 135 95 220 220 220 220

8 12 16 20 24 32

1/2 3/4 1 1 1/4 1 1/2 2

5/16-18 3/8-16 7/16-14 1/2-13 5/8-11 3/4-10

17 +/- 2 30 +/- 4.5 46 +/- 4.5 69 +/- 6 125 +/- 8 208 +/- 20

M8 M10 M12 M14 M16 M20

25 49 85 135 210 425

* Does not meet ISO 6162 specification.

Table T7 - Code 62 Flange Recommended Bolt Torque

* Does not meet ISO 6162 specification.

Table T6 - Code 61 Flange Recommended Bolt Torque

3.72

Tigercat 610E/615E Skidder

Lubrication and Maintenance

Parker

Assembly Torque

JIC 37 Degree Flare SAE Dash Size

Thread Size

-2 -3 -4 -5 -6 -8 -10 -12 -14 -16 -20 -24 -32 -40

NPTF

Tube Connection Swivel or Hose Connection FFWR FFWR

5/16-24 3/8-24 7/16-20 1/2-20 9/16-18 3/4-16 7/8-14 1 1/16-12 1 3/16-12 1 5/16-12 1 5/8-12 1 7/8-12 2 1/2-12 3-12

NA NA 2 2 1 1/2 1 1/2 1 1/2 1 1/4 1 1 1 1 1 1

SAE Dash Size

NA NA 2 2 1 1/4 1 1 1 1 1 1 1 1 1

-2 -3 -4 -5 -6 -8 -10 -12 -14 -16 -20 -24 -32 -40

F.F.W.R : Flats From Wrench Resistance All values are for Steel, Stainless Steel and Brass

1/8-27 NA 1/4-18 NA 3/8-18 1/2-14 7/8-14 3/4-14 NA 1-11 1/2 1 1/4-11 1/2 1 1/2-11 1/2 2-11 1/2 NA

Thread Size

-2 -3 -4 -5 -6 -8 -10 -12 -14 -16 -20 -24 -32 -40

NA NA 1/4 TO 1/2 NA 1/4 TO 1/2 1/4 TO 1/2 1/4 TO 1/2 1/4 TO 1/2 NA 1/4 TO 1/2 1/4 TO 1/2 1/4 TO 1/2 NA NA

2-3 NA 2-3 NA 2-3 2-3 NA 2-3 NA 1.5-2.5 1.5-2.5 1.5-2.5 1.5-2.5 NA

BSPT

Tube Connection Swivel or Hose Connection FFWR FFWR

NA NA 9/16-18 NA 11/16-16 13/16-16 1-14 1 3/16-12 NA 1 7/16-12 1 11/16-12 2-12 NA NA

2-3 NA 2-3 NA 2-3 2-3 NA 2-3 NA 1.5-2.5 1.5-2.5 1.5-2.5 1.5-2.5 NA

T.F.F.T. : Turns from finger tight All pipe values are for Steel, Stainless Steel and Brass

O'ring Face Seal / Seal-Lok SAE Dash Size

Tube Connection Swivel or Hose Connection TFFT TFFT

Thread Size

SAE Dash Size

NA NA 1/2 TO 3/4 NA 1/2 TO 3/4 1/2 TO 3/4 1/2 TO 3/4 1/3 TO 1/2 NA 1/3 TO 1/2 1/3 TO 1/2 1/3 TO 1/2 NA NA

-2 -3 -4 -5 -6 -8 -10 -12 -14 -16 -20 -24 -32 -40

F.F.W.R : Flats From Wrench Resistance All values are for Steel, Stainless Steel and Brass

Thread Size

Tube Connection Swivel or Hose Connection TFFT TFFT

1/8-28 NA 1/4-19 NA 3/8-19 1/2-14 NA 3/4-14 NA 1-11 1 1/4-11 1 1/2-11 2-11 NA

2-3 NA 2-3 NA 2-3 2-3 NA 2-3 NA 1.5-2.5 1.5-2.5 1.5-2.5 1.5-2.5 NA

2-3 NA 2-3 NA 2-3 2-3 NA 2-3 NA 1.5-2.5 1.5-2.5 1.5-2.5 1.5-2.5 NA

T.F.F.T. : Turns from finger tight All pipe values are for Steel, Stainless Steel and Brass

SAE J1926 Straight Thread Port Assembly Torques ASSEMBLY TORQUE = 10 % -0 SAE DASH SIZE

2 3 4 5 6 8 10 12 14 16 20 24 32

5/16-24 3/8-24 7/16-20 1/2-20 9/16-18 3/4-16 7/8-14 1 1/16-12 1 3/16-12 1 5/16-12 1 5/8-12 1 7/8-12 2 1/2-12

SEAL-LOK lbf•ft (lbf•in) (310) (310) (310) (360) (420) 60 100 135 175 200 250 305 375

N •m 20 20 20 40 46 80 135 185 235 270 340 415 510

TRIPLE-LOK FERULOK PIPE FITTINGS lbf•ft N •m (lbf•in) (85) 10 (155) 18 (260) 29 (280) 32 (350) 40 (620) 70 85 115 135 183 175 237 200 271 250 339 305 414 375 509

PLUGS

ADJUSTABLE

NON-ADJUSTABLE THREAD SIZE

SEAL-LOK lbf•ft (lbf•in) (310) (310) (310) (360) (420) 60 100 135 175 200 250 305 375

3.73

N •m 20 20 20 40 46 80 135 185 235 270 340 415 510

TRIPLE-LOK FERULOK PIPE FITTINGS lbf•ft N •m (lbf•in) (60) 7 (100) 11 (180) 20 (250) 28 (350) 40 (620) 70 85 115 135 183 175 237 200 271 250 339 305 414 375 509

HOLLOW HEX HP5ON-S lbf•ft (lbf•in) (30) (55) (120) (170) (410) 60 100 135 175 200 250 305 375

N •m 3.5 6 13.5 19 46 80 135 185 235 270 340 415 510

HEX HEAD P5ON-S lbf•ft (lbf•in) (85) (155) (260) (280) (350) (620) 85 135 175 200 250 305 375

N •m 10 18 29 32 40 70 115 183 237 271 339 414 509

Lubrication and Maintenance

Tigercat 610E/615E Skidder

EATON Aeroquip

Assembly Torque

Recommended Parallel Connection Assembly torque

Eaton recommends that a Torque wrench be used to assure proper fitting assembly of these connections.

Straight Thread O-Ring Boss Low Pressure with 37º (SAEJ514)

Straight Thread O-Ring Boss High Pressure with ORS (J1453)

Thread Size (inches) 3/8-24 7/16-20 1/2-20 9/16-18 3/4-16 7/8-14 1 1/16-12 1 3/16-12 1 5/16-12 1 5/8-12 1 7/8-12 2 1/2-12

Dash Size -03 -04 -05 -06 -08 -10 -12 -14 -16 -20 -24 -32

The values listed are for steel connections. Contact Teaton for torque values for other materials.

Jam Nut or Jam Nut or Straight Straight Fitting Torque Fitting Torque lb.-ft.

Newton Meters 8-9 12-13 13-15 18-20 14-15 19-21 23-24 32-33 40-43 55-57 43-48 59-64 68-75 93-101 83-90 113-122 112-123 152-166 146-161 198-218 154-170 209-230 218-240 296-325

Dash Size -03 -04 -05 -06 -08 -10 -12 -14 -16 -20 -24

ORS

Dash Size -04 -06 -08 -10 -12 -16 -20 -24

Thread Size (inches) 3/8-24 7/16-20 1/2-20 9/16-18 3/4-16 7/8-14 1 1/16-12 1 3/16-12 1 5/16-12 1 5/8-12 1 7/8-12

Jam Nut or Jam Nut or Straight Straight Fitting Torque Fitting Torque lb.-ft.

Newton Meters 8-10 11-16 14-16 20-22 18-20 24-27 24-26 33-35 50-60 68-78 72-80 98-110 125-135 170-183 160-180 215-245 200-220 270-300 210-280 285-380 270-360 370-490

SAE 37º (JIC) Thread Size (inches) 9/16-18 11/16-20 13/16-16 1-14 1 3/16-12 1 7/16-12 1 11/16-12 2-12

Swivel Nut Torque lb.-ft.

10-12 18-20 32-35 46-50 65-70 92-100 125-140 150-165

Swivel Nut Torque Newton Meters 14-16 24-27 43-47 62-68 88-95 125-136 170-190 204-224

Dash Size -04 -05 -06 -08 -10 -12 -16 -20 -24 -32

Metric Thread Size mm M10x1 M12x1.5 M14x1.5 M16x1.5 M18x1.5 M20x1.5 M22x1.5 M26x1.5 M27x2 M33x2 M42x2 M48x2

Thread Size (inches) 7/16-20 1/2-20 9/16-18 3/4-16 7/8-14 1 1/16-12 1 5/16-12 1 5/8-12 1 7/8-12 2 1/2-12

Swivel Nut Torque lb.-ft.

11-12 15-16 18-20 38-42 57-62 79-87 108-113 127-133 158-167 245-258

Swivel Nut Torque Newton Meters 15-16 20-22 24-28 52-58 77-85 108-119 148-154 173-182 216-227 334-352

BSPP Straight Adapter or Locknut Torque lb.-ft.

Newton Meters 13-15 18-20 15-19 20-25 19-23 25-30 33-40 45-55 37-44 50-60 52-66 70-90 55-70 75-95 81-96 110-130 96-111 130-150 162-184 220-250 170-192 230-260 258-347 350-470

Nominal Thread Size Straight Adapter or Locknut Torque inches** lb.-ft.

Newton Meters G1/8-28 13-15 18-20 G1/4-19 19-23 25-30 G3/8-19 33-40 45-55 G1/2-14 55-70 75-95 G3/4-14 103-118 140-160 G1-11 162-184 220-250 G1 1/4-11 170-192 230-260 G1 1/2-11 258-347 350-470 ** "G" denotes parallel threads, other than ISO 6149 (Port connection only)

Eaton Aeroquip Fluid Conveyance Products A-HOOV-MC001-E January 2005

3.74

Tigercat 610E/615E Skidder

Lubrication and Maintenance

Weights of Commercial Wood

Species

kg/m3

lb/ft3

Species

kg/m3

lb/ft3

Alder, Red Ash, White Aspen, Quaking Bald Cypress Basswood, American Beech, American Birch, Paper Birch, Yellow Cedar, Alaska Cedar, Incense Cedar, Northern White Cedar, Port-Orford Cedar, Western Red Cherry, Black Cottonwood, Eastern Douglas Fir, Coast Douglas Fir, Inland North Elm, American Fir, Alpine Fir, Balsam Fir, Nobel Fir, Red Fir, Silver Fir, White Gum, Black Gum, Blue Gum, Red Gum, Tupelo Hemlock, Eastern Hemlock, Western Hickory, Pecan Hickory, True Larch, Western Locust, Black Magnolia, Cucumber

737 769 689 817 673 865 801 929 577 721 449 897 433 721 785 881 577 865 449 721 481 769 577 753 721 1121 801 897 801 657 993 1009 769 929 785

46 48 43 51 42 54 50 58 36 45 28 36 57 45 49 55 36 54 28 45 30 48 36 47 45 70 50 56 50 41 62 63 48 58 49

Maple, Big Leaf Maple, Black Maple, Red Maple, Silver Maple, Sugar Oak, Black Oak, Chestnut Oak, Red Oak, Red, Swamp Oak, Swamp Chestnut Oak, White Oak, White, Swamp Pine, Jack Pine, Loblolly Pine, Lodgepole Pine, Long Leaf Pine, Norway, Red Pine, Short Leaf Pine, Slash Pine, Sugar Pine, Western Yellow Pine, White-Western Pine, White-Eastern Poplar, Yellow Redwood Spruce, Black Spruce, Engleman Spruce, Red Spruce, Sitka Spruce, White Sweetgum Sycamore, American Tamarack Walnut, Black Willow, Black

753 865 801 721 897 1009 977 1009 1073 1041 993 1105 801 993 625 993 673 993 993 817 721 561 577 609 801 513 625 545 529 545 801 833 753 929 801

47 54 50 45 56 63 61 63 67 65 62 69 50 62 39 62 42 62 62 51 45 35 36 38 50 32 39 34 33 34 50 52 47 58 50

Note: The values shown here are green weights.

3.75

Lubrication and Maintenance TIRE PRESSURES Tigercat Part # BP056 BP111 BP112 BP022 BP113 BP114 BP139 BP137 BP145 BP100 BP066 BP039 BP167 BP143

Tigercat 610E/615E Skidder

Manufacturer Bridgestone/Firestone Bridgestone/Firestone Bridgestone/Firestone Bridgestone/Firestone Bridgestone/Firestone Bridgestone/Firestone Goodyear Goodyear Goodyear GPX Tire (Primex) Nokian Nokian Nokian Nokian

Inflation Pressure

Size 28L-26 16PR LS2 DW (FS) 30.5L-32 20PR LS2 (FS) 30.5L-32 26PR SS LS2 DH (FS) 73x44-32 16PR HF3 DH (FS) 35.5L-32 20PR LS2 DH (FS) 35.5L-32 24PR LS2 DH (FS) 30.5L-32 20 PR LOGLUGIII LS2 TL 30.5L-32 26 PLY CRC SS TUBELESS 35.5L-32 26PR LOGLUGIII TLL S2 66/4300-26 20PR HF4 DW (GPX) 750/55-26.5 20PR F (N) 750/55-26.5 20PR TRS (N) 780-50-28.5 24PR FOREST KING F2 SF 780/55-26.5 20PR F

psi 35 35 45 30 35 40 35 45 40 50 87 87 87 87

kPa 240 240 310 210 240 275 240 310 275 345 600 600 600 600

SKIDDER TIRE PRESSURES R4 04/13

COMMON CONVERSIONS To Convert bar cm3 °C kg kW L mm N-m N

Into psi in3 °F lb hp US gal in lbf-ft lbf

To Convert

Multiply By

Into

Multiply By

in3 cm3 16.39 °F °C (°F - 32) /1.8 US gal L 3.785 hp kW 0.7457 in mm 25.4 lb kg 0.4535 lbf-ft N-m 1.356 psi bar 0.06896 lbf N 4.4482 in of Hg psi . 4912 in of H2O psi . 03613

14.5 0.06102 (°C x 9/5) + 32 2.205 1.341 0.2642 0.03937 0.7375 0.22481

3.76