Sony PCG-FX220 FX220K FX240 FX240K PCG-FX250 FX250K FX270 FX270K NOTEBOOK COMPUTER SERVICE MANUAL -

PCG-FX220/FX220K/FX240/FX240K/ PCG-FX250/FX250K/FX270/FX270K

SERVICE MANUAL

US Model Canadian Model

S400

Illust : PCG-FX270K

l a i t

n e d i f

n o C

NOTEBOOK COMPUTER 9-872-227-11

Information in this document is subject to change without notice.

Caution Markings for Lithium/Ion Battery - The following or similar texts shall be provided on battery pack of equipment or in both the

Sony and VAIO are trademarks of Sony. Intel logo and Intel Inside logo are registered trademarks of Intel Corporation. Pentium MMX

operating and the service instructions.

is a trademark of Intel Corporation. Microsoft, MS-DOS, Windows, the Windows 95 and Windows 98 logo are trademarks of Microsoft

CAUTION: Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type recommended by

Corporation.

the manufacturer. Discard used batteries according to the manufacturer’s instructions.

All other trademarks are trademarks or registered trademarks of their respective owners. Other trademarks and trade names may be

CAUTION: The battery pack used in this device may present a fire

used in this document to refer to the entitles claiming the marks and names or their produces. Sony Corporation disclaims any proprietary

or chemical burn hazard if mistreated. Do not disassemble, heat above 100°C (212°F) or incinerate.

interest in trademarks and trade names other than its own.

Dispose of used battery promptly.

Keep away from children.

CAUTION: Changing the back up battery.

• Overcharging, short circuiting, reverse charging, multilation or incineration of the cells must be avoided to prevent one or more of the following occurrences; release of toxic materials, release of hydrogen and/or oxygen gas, rise in surface temperature.

• If a cell has leaked or vented, it should be replaced immediately while avoiding to touch it without any protection.

Service and Inspection Precautions 1. Obey precautionary markings and instructions

4. Inspect after completing service

Labels and stamps on the cabinet, chassis, and components identify areas requiring special precautions. Be sure to observe these precautions, as well as all precautions listed in the operating manual and other associated documents.

After servicing, inspect to make sure that all screws, components, and wiring have been returned to their original condition. Also check the area around the repair location to ensure that repair work has caused no damage, and confirm safety.

2. Use designated parts only

5. When replacing chip components...

The set’s components possess important safety characteristics, such as noncombustibility and the ability to tolerate large voltages. Be sure that replacement parts possess the same safety characteristics as the originals.

Also remember that the 0 mark, which appears in circuit diagrams and parts lists, denotes components that have particularly important safety functions; be extra sure to use only the designated components.

Never reuse components. Also remember that the negative side of tantalum capacitors is easily damaged by heat.

3. Always follow the original design when mounting parts and routing wires

6. When handling flexible print boards...

• The temperature of the soldering-iron tip should be about 270C. • Do not apply the tip more than three times to the same pattern.

• Handle patterns with care; never apply force.

The original layout includes various safety features, such as inclusion of insulating materials (tubes and tape) and the mounting of parts above the printer board. In addition, internal wiring has been routed and clamped so as to keep it away from hot or high-voltage parts. When mounting parts or routing wires, therefore, be sure to duplicate the original layout.

Caution: Remember that hard disk drives are easily damaged by vibration. Always handle with care.

ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ!

LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.

Confidential PCG-FX220/FX220K/FX240/FX240K/ PCG-FX250/FX250K/FX270/FX270K (UC)

—2—

TABLE OF CONTENTS Section

Title

Page

CHAPTER 1. REMOVAL 1-1.

1-2.

1-3.

1.

2.

Section

Title

Page

CHAPTER 2. SELF DIAGNOSTICS ......................... 2-1

Flowchart ......................................................................... 1-1 Main Electrical Parts Location Diagram ......................... 1-1 Removal ........................................................................... 1-2 Hood Keyboard Assy, Keyboard Unit .............................. 1-2 DC-Fan, Lithium Battery, Combination Drive, DVD-ROM Drive ............................................................. 1-2 3. Combination Drive, DVD-ROM Drive ............................ 1-3 1. FX240/FX240K/FX250/FX250K/ FX270/FX270K Model ................................................ 1-3 2. FX220/FX220K Model ................................................ 1-3 4. HDD, Door Battery .......................................................... 1-4 5. Palm Rest Assy, Touch Pad, CNX-125 Board, Palm Rest Plate, Bracket Pad ........................................... 1-4 6. Display Assy, Hinge Cover .............................................. 1-5 7. PWS-13 Board, Latch Detector ...................................... 1-6 8. PC Card Connector, Modem Card, MBX-49 Board, I/O Bracket ........................................... 1-6 9. Speaker Unit, SWX-73 Board ......................................... 1-7 10. SO-DIMM ........................................................................ 1-7 11. Modem Card (Removing from the bottom) ..................... 1-8 12. LCD Section (FX270/FX270K Model) – Made by HI – ....................... 1-9 1. Bezel Housing Assy, LCD unit (15 inch) .................... 1-9 2. Inverter Assy, LCD Harness, FPC, Display Hpusing Assy ................................................ 1-10 13. LCD Section (FX220/FX220K/FX250/FX250K Model) – Made by HI – .............................................................. 1-11 1. Bezel Housing Assy, LCD unit (15 inch) .................. 1-11 2. Inverter Assy, LCD Harness, FPC, Display Hpusing Assy ................................................ 1-12 14. LCD Section (FX240/FX240K Model) – Made by HI – ..................... 1-13 1. Bezel Housing Assy (14 inch) ................................... 1-13 2. Bracket LCD Left, Bracket LCD Right, LCD Unit (14 inch) .................................................... 1-14 3. FPC, Inverter Assy, Display Housing Assy, LCD Harness .............................................................. 1-14 1-4. Replacing the CPU ........................................................ 1-15 1. Socket type 1,2 ............................................................... 1-15 1. Removing the CPU .................................................... 1-15 2. Installing the CPU ...................................................... 1-15 2. Socket type 3 .................................................................. 1-16 1. Removing the CPU .................................................... 1-16 2. Installing the CPU ...................................................... 1-16 1-5. Replacing Various Connector on the MBX-49 Board ... 1-17 1. Removing the I/O Bracket ............................................. 1-17 2. Removing the Various Connectors ................................. 1-17 1-6. DIP Switch Setting of the MBX-49 Board .................... 1-18 (to 1-18)

(to 2-1)

CHAPTER 3. BLOCK DIAGRAM ............................... 3-1 (to 3-2)

CHAPTER 4. FRAME HARNESS DIAGRAM ........ 4-1 (to 4-2)

CHAPTER 5. EXPLODED VIEWS AND PARTS LIST ............................................ 5-1 5-1. Main Section .................................................................... 5-3 5-2. LCD Section (FX270/FX270K Model) – Made by HI – ....................... 5-7 5-3. LCD Section (FX220/FX220K/FX250/FX250K Model) – Made by HI – ................................................................ 5-9 5-4. LCD Section (FX240/FX240K Model) – Made by HI – ..................... 5-11 5-5. Connector Section .......................................................... 5-13 (to 5-14)

•

Abbreviations UC : US model / Canadian model

Confidential —3—

PCG-FX220/FX220K/FX240/FX240K/ PCG-FX250/FX250K/FX270/FX270K (UC)

CHAPTER 1.

REMOVAL 1-1. Flowchart

CNX-125 BOARD P 1-4 PALM REST PLATE

BRACKET PAD

TOUCH PAD

P 1-4

P 1-4

P 1-4

COMBINATION DVD-ROM DRIVE

P 1-2 P 1-3

HINGE COVER P 1-5

DISPLAY ASSY

BEZEL HOUSING ASSY

LCD UNIT ∗P 1-9 (P 1-11) 〈P 1-14〉

∗P 1-9 (P 1-11) 〈P 1-13〉

P 1-5

HOOD KEYBOARD ASSY

KEYBOARD UNIT

DOOR BATTERY

P 1-2

P 1-2

P 1-4

SO-DIMM

SPEAKER UNIT

PC CARD CONNECTOR

P 1-7

P 1-7

P 1-6

BATTERY PACK

SWX-73 BOARD

HDD

P 1-7

P 1-4

BRACKET LCD RIGHT

DC-FAN

〈P 1-14〉

FDD

PALM REST ASSY P 1-4

LATCH DETECTOR

PWS-13 BOARD

I/O BRACKET

MBX-49 BOARD

P 1-6

P 1-6

P 1-6

P 1-6

MODEM CARD P 1-6

P 1-2

DISPLAY HOUSING ASSY

∗P 1-10 (P 1-12) 〈P 1-14〉

LCD HARNESS ∗P 1-10 (P 1-12) 〈P 1-14〉

LITHIUM BATTERY P 1-2

POWER OFF

INVERTER ASSY ∗P 1-10 (P 1-12) 〈P 1-14〉

FPC ∗P 1-10 (P 1-12) 〈P 1-14〉 BRACKET LCD LEFT 〈P 1-14〉

∗ : FX270/FX270K Model ( ) : FX220/FX220K/FX250/FX250K Model 〈 〉 : FX240/FX240K Model

MODEM CARD P 1-8

• P XX means pages that appears in this manual.

• Remember that hard disk drives are easily damaged by vibration. Always handle with care.

1-2. Main Electrical Parts Location Diagram LCD Unit

Speaker Unit DC Fan Inverter Assy HDD

SWX-73 Board Speaker Unit

MBX-49 Board CNX-125 Board

Combination Drive (CD-RW/DVD-ROM) DVD-ROM Drive Modem Card

PWS-13 Board FD Drive

Touch Pad 1-1

Confidential PCG-FX220/FX220K/FX240/FX240K/ PCG-FX250/FX250K/FX270/FX270K (UC)

1-3.Removal 1. Hood Keyboard Assy, Keyboard Unit 3M2X4 Special Head (Black)

4Pull it up sliding it to the right.

8M2X4 Special Head (Black)

6Hood Keyboard Assy

q;Keyboard Unit

7 5

Four Claws 1 9

2

MBX-49 Board CN2004

MBX-49 Board CN1902

2. DC-Fan, Lithium Battery, Combination Drive, DVD-ROM Drive 5Screw (M2) 0 Number P3 Kind (X4) (Black) 2+B M2 (X2) (Gold) 3Plate ground

1 MBX-49 Board CN102

7DC Fan 4 6

9M2X6 Special Head (Gold)

MBX-49 Board CN102

8 qaCombination Drive DVD-ROM Drive q;

Confidential PCG-FX220/FX220K/FX240/FX240K/ PCG-FX250/FX250K/FX270/FX270K (UC)

1-2

3. Combination Drive, DVD-ROM Drive 1. FX240/FX240K/FX250/FX250K/FX270/FX270K Model

5Bracket CD-ROM R 3+B M2 (X2) (Gold)

4+B M2 (X2) (Gold)

8COMBO Drive

6Screw (M1.7) (X3) (Black)

Claw 2Bracket (CD-ROM L) 1+B M2 (X2) (Gold)

7DVD-RW Door Assy

2. FX220/FX220K Model

3+B M2 (X2) (Silver)

5Bracket CD-ROM R

8DVD-ROM Drive

4+B M2 (X2) (Silver) 6Tapping screw (B1.7) (Black)

Two claws

2Bracket (CD-ROM L)

7DVD-ROM Door Assy

1+B M2 (X2) (Silver)

Confidential 1-3

PCG-FX220/FX220K/FX240/FX240K/ PCG-FX250/FX250K/FX270/FX270K (UC)

4. HDD, Door Battery 1M2X6 Special Head (X6) (Gold) 1Screw M3X4 (X2) (Gold) 3

3Bracket HDD

2FPC 50Pin (for HDD) MBX-49 Board CN2201

5HDD

4FPC 50Pin (for HDD)

2Screw M3X4 (X2) (Gold)

4Door Battery

5. Palm Rest Assy, Touch Pad, CNX-125 Board, Palm Rest Plate, Bracket Pad 3Pull it to the front slightly and raise to remove it.

Palm Rest Assy

1M2X4 Special Head (Black)

7CNX-125 Board

9Touch Pad

4

8FPC (TP-CNX) PWS-13 Board CN4004

6FPC (SWX-PWX) 5Bracket Pad 4Remove by pressing to rear.

3Palm Rest Plate

2Move down the front

1M2X4 Special Head (x4) (Black)

portion slightly downward and then pull it out.

2Screw (M2), 0 Number P3 Kind (X4) (Black)

Confidential PCG-FX220/FX220K/FX240/FX240K/ PCG-FX250/FX250K/FX270/FX270K (UC)

1-4

6. Display Assy, Hinge Cover

1Stand the LCD upright to the MBX-49 board.

7M2.6 Cross (Hole) Bind (Black)

3+B M2 (X2) (Gold) 9M2X6 Special Head (Gold)

4Plate ground

q;+B 2X12 (Silver)

qaM2X6 Special Head (Black)

2

qs 5M2.6 Cross (Hole) Bind (Black)

Six Claws

6M2.6 Cross (Hole) Bind (X2) (Black)

MBX-49 Board CN701

8Screw (M2), 0 Number P3 Kind (Black) qdClose simultaneously both left and right hinges approximately 90° in the direction of the arrow.

qfCover Hinge qhDisplay Base

Four Claws

qg

Note : To remove the cover hinge, bend slightly the center of the display base facilitates the removal work.

Display Assy

Confidential 1-5

PCG-FX220/FX220K/FX240/FX240K/ PCG-FX250/FX250K/FX270/FX270K (UC)

7. PWS-13 Board, Latch Detector 2M2X4 Special Head (X2) (Black)

6PWS-14 Board 5Latch Detector 1

3 MBX-50 Board CON22

4Two Claws

8. PC Card Connector, Modem Card, MBX-49 Board, I/O Bracket qhI/O Bracket qgScrew (HEX) (X6) (Silevr)

2+B 2X4 (Silver) 1M2X4 Special Head (X4) (Black)

CPU*1

9PC Card Connector

qdNUT M2 TYPE2 (X2)

qjMBX-50 Board 3Screw (MBX) (Silver) 8+B 2X14 (X2) (Silver)

CON4 qa qfSpacer (MBX) (X2)

7

4M2X4 Special Head (X2) (Black)

qsModem Card*2 q;M2 Grip (X2) (Black)

5Bracket Bay Connector

6Screw (M2) 0 Number P3 Kind (X2) (Black)

Confidential PCG-FX220/FX220K/FX240/FX240K/ PCG-FX250/FX250K/FX270/FX270K (UC)

∗1 When removing the CPU, refer to “ 1-4. Replacing the CPU ”. ∗2 Modem card can be removed from the bottom.

Refer to the subsequent paragraph “ 11. Modem card ” for more details.

1-6

9. Speaker Unit, SWX-73 Board 6M2X4 (X2) (Black) Note : When removing the speaker unit, be sure not to damage the hood keyboard.

4M2X4 (X5) (Black) SWX-73 Board CN301 SWX-73 Board CN302

7Speaker Unit 3 5SWX-73 Board SWX-73 Board CN303

8M2X4 (X2) (Black)

1 2 Note : To re-install it, align the notch of the speaker unit with the projection of the hood keyboard.

9Speaker Unit

Notch

Speaker Unit Notch Hood Keyboard Projection

Projection Hood Keyboard

10. SO-DIMM 1M2X4 Special Head (Black) 2DIMM Door

Removal of SO-DIMM a→b a b

a

Confidential 1-7

PCG-FX220/FX220K/FX240/FX240K/ PCG-FX250/FX250K/FX270/FX270K (UC)

11. Modem Card (Removing from the bottom)

1M2X4 Special Head (Black) 2Modem Door 3M2 Grip (X2) (Black)

4Modem Card

5

Confidential PCG-FX220/FX220K/FX240/FX240K/ PCG-FX250/FX250K/FX270/FX270K (UC)

1-8

12. LCD Section (FX270/FX270K Model) – Made by HI – 1. Bezel Housing Assy, LCD unit (15 inch)

1Cover Screw Side (15) (X3) 3Cover Screw Shaft 4+P 2.6X6 Lock Precision b Type3 (Black)

2M2X3 Special Head (X3) (Gold) Bezel Housing Assy a : claw part

7

3Cover Screw Shaft

2M2X3 Special Head (X3) (Gold)

Cover Screw Side (15) (X3)

c b

How to release the claw a

4+P 2.6X6 Lock Precision Type3 (Black)

Bezel Housing Assy

0 a LCD unit Display Housing Assy 8

Pull the Bezel Housing Assy as shown to release the claw a.

9

Order of releasing the claws c → b → a Order of locking the claws a → b → c

Display Housing Assy

6M2X4 Special Head (Black) 5Cover Screw Lower

Confidential 1-9

PCG-FX220/FX220K/FX240/FX240K/ PCG-FX250/FX250K/FX270/FX270K (UC)

2. Inverter Assy, LCD Harness, FPC, Display Hpusing Assy

3Filament Tape 8LCD HARNESS 1M2X4 Special Head (Black)

2 2

4 6 5Inverter Assy

7FPC

9Display Housing Assy

Confidential PCG-FX220/FX220K/FX240/FX240K/ PCG-FX250/FX250K/FX270/FX270K (UC)

1-10

13. LCD Section (FX220/FX220K/FX250/FX250K Model) – Made by HI – 1. Bezel Housing Assy, LCD unit (15 inch)

1Cover Screw Side (15) (X3) 3Cover Screw Shaft 4+P 2.6X6 Lock Precision b Type3 (Black)

2M2X3 Special Head (X3) (Gold) Bezel Housing Assy a : claw part

7

3Cover Screw Shaft

2M2X3 Special Head (X3) (Gold) 1Cover Screw Side (15) (X3)

c b

How to release the claw a

4+P 2.6X6 Lock Precision Type3 (Black)

Bezel Housing Assy

0 a LCD unit Display Housing Assy 8

Pull the Bezel Housing Assy as shown to release the claw a.

9

Order of releasing the claws c → b → a Order of locking the claws a → b → c

Display Housing Assy

6M2X4 Special Head (Black) 5Cover Screw Lower

Confidential 1-11

PCG-FX220/FX220K/FX240/FX240K/ PCG-FX250/FX250K/FX270/FX270K (UC)

2. Inverter Assy, LCD Harness, FPC, Display Hpusing Assy 3Filament Tape 8LCD HARNESS 1M2X4 Special Head (Black)

2 2

4 6 5Inverter Assy

7FPC

9Display Housing Assy

Confidential PCG-FX220/FX220K/FX240/FX240K/ PCG-FX250/FX250K/FX270/FX270K (UC)

1-12

14. LCD Section (FX240/FX240K Model) – Made by HI – 1. Bezel Housing Assy (14 inch)

1Cover Screw Lower (X2) 2M2X4 Special Head (X2) (Black) b

: claw part a

1Cover Screw Upper (X2) 2M2X4 Special Head (X2) (Black)

3

Bezel Housing Assy

c b

4M2X4 Special Head (X5) (Black)

4M2X4 Special Head (X5) (Black)

7 How to release the claw a

LCD Unit 5

6 Bezel Housing Assy Display Housing Assy a

Display Housing Assy Pull the Bezel Housing Assy as shown to release the claw a.

Inverter Assy Inverter Assy CN2

Order of releasing the claws c → b → a Order of locking the claws a → b → c

Confidential 1-13

PCG-FX220/FX220K/FX240/FX240K/ PCG-FX250/FX250K/FX270/FX270K (UC)

2. Bracket LCD Left, Bracket LCD Right, LCD Unit (14 inch)

3+P M2x3 Lock (X4) (Gold) 5LCD Unit 1+P M2x3 Lock (X4) (Gold) 4Bracket LCD Left

2Bracket LCD Right

3. FPC, Inverter Assy, Display Housing Assy, LCD Harness

8LCD Harness

6M2X4 Special Head (Black)

5M2X4 Special Head (Black) 1

3

4FPC 7Display Housing Assy

: claw part

Confidential PCG-FX220/FX220K/FX240/FX240K/ PCG-FX250/FX250K/FX270/FX270K (UC)

1-14

2Inverter Assy

1-4.Replacing the CPU NOTE: This computer uses either one of the two types of CPU socket.

The CPU locking position and the lock-release position are different depending on the types of the CPU socket.

1. Socket type 1, 2 1. Removing the CPU 1 1 Insert a flat-blade screwdriver into the notch as shown in the illustration and rotate it so that the protrusion comes to the lock release position.

2 Pull the CPU gently upward to lift it out of the CPU socket.

CPU

2

CPU socket

Lock release position (made by HIROSE)

Lock release position

2. Installing the CPU 2 1 Align the triangle reference mark of the CPU with that of the CPU socket CPU and insert all the pins of the CPU to the corresponding holes of the CPU socket.

2 Insert a flat-blade screwdriver into the notch as shown in the illustration and rotate it so that the protrusion comes to the lock position.

Reference marks

1

CPU socket

Lock position (made by HIROSE)

Lock position

NOTE: Rotate a flat-blade screwdriver to the lock position securely. If not, the operation of the CPU may become unstable.

Confidential 1-15

PCG-FX220/FX220K/FX240/FX240K/ PCG-FX250/FX250K/FX270/FX270K (UC)

2. Socket type 3 1. Removing the CPU 1 CPU

2 L

O

Protrusion Lock release position [O]

CPU socket

1 Insert a flat-blade screwdriver into the notch as shown in the illustration and rotate it so that the protrusion comes to the “O” (lock release) position.

2 Pull the CPU gently upward to lift it out of the CPU socket.

2. Installing the CPU

1 CPU

2

CPU socket

Lock position [L] L Protrusion Reference marks

O

1 Align the triangle reference mark of the CPU with that of the CPU socket and insert all the pins of the CPU to the corresponding holes of the CPU socket.

2 Insert a flat-blade screwdriver into the notch as shown in the illustration and rotate it so that the protrusion comes to the “L” (lock) position.

NOTE: • Considerable force is required to rotate a flat-blade screwdriver.

• Rotate a flat-blade screwdriver to the “L” (lock) position securely. If not, the operation of the CPU may become unstable.

Confidential PCG-FX220/FX220K/FX240/FX240K/ PCG-FX250/FX250K/FX270/FX270K (UC)

1-16

1-5. Replacing Various Connectors on the MBX-49 Board Replace the connectors of “5-5. Connector Section” as follows.

1. Removing the I/O Bracket When removing the connectors of reference numbers 164, 165 and 167 (refer to page 5-13), remove the I/O bracket first.

+B 2X4 (X2) (Silver)

I/O Bracket

Screw (HEX) (X6) (Silver)

MBX-49 Board

2. Removing the Various Connectors The connectors of reference numbers 164, 165 and 167 (Refer to page 5-13, 5-14) are connected by soldering, remove the soldering first then remove the connectors.

Confidential 1-17

PCG-FX220/FX220K/FX240/FX240K/ PCG-FX250/FX250K/FX270/FX270K (UC)

1-6. DIP Switch Setting of the MBX-49 Board Set the DIP switch on the MBX-49 board (main board) to match with the LCD that is used in this computer, because several types of LCD are used as shown in the following table and the DIP switch setting differs depending on the LCD type.

Name of LCD

Part No.

DIP switch setting

FX270/FX270K

HI

1-476-300-11

The upper position where ON indication is shown is the ON position . The lower position is the OFF position.

1 2 3 4 5 6 7 8

O N

MODEL

1 2 3 4 5 6 7 8 ON/OFF 0 0 0 0 0 1 1 1 No.

1: OFF

1 2 3 4 5 6 7 8

O N

0 : ON

FX220/FX220K FX250/FX250K

HI

1-476-186-12

The upper position where ON indication is shown is the ON position . The lower position is the OFF position.

1 2 3 4 5 6 7 8 ON/OFF 0 0 0 0 1 1 1 1 No.

1: OFF

1 2 3 4 5 6 7 8

O N

0 : ON

FX240/FX240K

HI

1-476-789-11

The upper position where ON indication is shown is the ON position . The lower position is the OFF position.

No. ON/OFF

1 2 3 4 5 6 7 8 0 0 1 0 0 1 1 1 0 : ON

Confidential PCG-FX220/FX220K/FX240/FX240K/ PCG-FX250/FX250K/FX270/FX270K (UC)

1-18 (END)

1: OFF

CHAPTER 2.

SELF DIAGNOSTICS

ATTENTION Please confirm “Self Diagnostics” method which will be informed you with distribution of “Self Diagnostics” software.

Confidential 2-1 (END)

PCG-FX220/FX220K/FX240/FX240K/ PCG-FX250/FX250K/FX270/FX270K (UC)

CHAPTER 3.

BLOCK DIAGRAM

CPU Volt Reg

SO-DIMM Socket 2

TV Encoder CH7007A

(LED Signal Include)

LVDS

CNX-126

1 Row# 0,1

i.Link TI TSB43AA22PD T

Cardbus RICOH R5C476 II

AHA

2

9

RJ-45 9

USB PORT2

Audio

AC Link

AD1881A

FW82801

Ext. MIC

MODEM MDC Module MDC CN BtoB(40pin)

EEPROM for Password SMBUS2

Debug Board CN BtoB (30pin)

CLK GEN SO-DIMM

LPC

AHA viaLPC

Super I/O SMSC LPC47N227

FWH Multi Purpose Bay

EC/KBC/ SPIC

PS/2

RS232C Buffer

I/O Expander /SMBUS MUX

SMBUS0

O2micro OZ998

HITACHI H8S/2149

VGA Serial DSUB-9 Parallel DSUB-25 RJ-45 ETHER USB PORT0

7

USB PORT2

5

USB PORT3

12

PS/2 MiniDIN-6 for KBD

8

Batter2

CN

PPK 3

CNX-125 (Touchpad BTN) CN

10

Power BTN

Touch pad CN

SWX-73 (PPK&SPKR CN)

CN

Bay CN (50pin)

11

2

Batter1

CN

Parallel Dsub-25

FDD

PWS-13 (Battery CONN & LidSW)

FAN

LED

12

Flash BIOS ROM

ATF Sense FAN control ADM1030

SMBUS1

CN

Int. Keyboard

(FDD/2ndBattery)

DC-IN

Secondary IDE CN

FPC(50pin)

Optical Devices

RJ-11

CN

BtoB CN (50pin)

Primary IDE

USB Port 1 Serial Dsub-9

8

Headphone Am p

CNX-123

CN

USB PORT3

6

10

CN

4 Am p

CN

5

LCI

CN

7

USB PORT1

4

Ether PHY 82562ET

CN

6

3

P C I Bus

USB PORT 0

Refer to Clock Generator Block Diagram

Master IDE Device

1

100-pin Port Replicator CONNECTOR

SMBUS2

VDC_IN

DVO

GMBUS

FW82815

FW82801

Slot x2

FW82807

DVO

HDD

PC Card

i.Link 4-pin

Row# 2,3

CLK GEN IMI C9835

Port Replicator

100-pin Port Replicator CONNECTOR

SO-DIMM Socket 1

VGA DSub-15

(Cache:256kB OD)

PC100 SO-DIMM

w/ Port Replicator (PCGA-PRFX1) 10/10/00

LCD 50pin CN

Socket 2

MP III 850/800/ 750 MHz

mini Jack

FW82801

PC Card

VID Selector

CPU

TV-OUT

11

Socket 1

ITP Connector

Memory Subsystem

SMBUS2

PCG-FX Series BLOCK DIAGRAM Rev. 1.00 PC Card

µ-PGA2 Connector

Stereo Speaker

Confidential 3-1

3-2 (END)

PCG-FX220/FX220K/FX240/FX240K/ PCG-FX250/FX250K/FX270/FX270K (UC)

CHAPTER 4.

FRAME HARNESS DIAGRAM DC-IN

USB

MONITOR

NETWORK

PRINTER

SERIAL

USB

PHONE

1

Rear Panel

20

LCD

KEY BOARD INVERTER DC FAN

CN802 CN1

144

CN2701

2

1 2

18

CN101

FPC

Speaker L

Speaker R

59 60

1

CN301 10

1

1

1

SWX-73 (Side-A)

COMBINATION DVD-ROM DRIVE

RAM 1 2

59

CN4005

1

PC100 SO-DIMM PC100 SO-DIMM (FX270/FX270K Model) 128MB 64MB (FX220/FX220K/FX240/ FX240K/FX250/FX250K Model) OPTION

FLOPPY DISK DRIVE

PWS-13 Board (Side-B)

6

BATTERY PACK

60

CN4001

RAM

29 30

144

1

76 CN1202

PC CARD CONNECTOR

J1

1 2

1

CN102

MODEM CARD

30

2

CN501

2

143 2

2

HARD DISK

MBX-49 Board (Side-A)

2

1

75

150

2

Side

1 CN1602 29

143

CN303

CN502

1

1

CN1301

8

CN5002 CN5001 1

12 1

8

CNX-125 Board (Side-A)

1

6

CN4004 CN4002

IEEE 1394 i.LINK

CN302

CN1703

1

HEADPHONE

FPC

CN2301

CN1701

CNX-123 Board (Side-A)

50

EXTERNAL MICROPHONE

CN103 CN152 CN151

50 49 CN2201

2 1

CN2004 CN2602 1 8 1 1 10 2

CN105

2nd BATTERY PACK (OPTION)

From board to connector (direct connection) Harness (connector at both end) Harness (soldered at one end) Connectors soldered on board and appearing on the panel

1

VIDEO OUT

25

CN1401

50

49

CN701

30 29

1

CN1902 1 99 100

CPU

CN3001

2

1

50

CN2302 49

2

2 1

CN1802

CN1801

CN1502

1

CN702

CN2801 CN1101

18

FFC LED

TOUCH PAD

Confidential 4-1

4-2 (END)

PCG-FX220/FX220K/FX240/FX240K/ PCG-FX250/FX250K/FX270/FX270K (UC)

CHAPTER 5.

EXPLODED VIEWS AND PARTS LIST NOTE: The components identified by mark 0 or dotted line with mark 0 are critical for safety.

Replace only with part number specified.

• The mechanical parts with no reference number in the exploded views are not supplied.

• Items marked “ * ” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items.

• When two or more parts are shown in parallel, use the part described first as the main part.

Les composants identifiés par une marque 0 sont critiques pour la sécurité.

Ne les remplacer que par une pièce portant le numéro spécifié.

How to use properly the repair parts.

There are some parts that use the 2 types ; the [CH] parts or alternately the [JP] parts, in this series.

Use the [CH] repair parts for the [CH] type product, vice versa. [ How to identify the parts ]

1M2X4 Special Head (Black)

2DIMM Door

Identfication Seal

Serial No.

A-xxx-xxx-A x xxxxxxxxx 1 or 2 : Using [JP] type 6 : Using [CH] type

Identification seal is attached on the expansion memory connector.

[ Repair part description example ] Ref.No. Part No. 999 999

Description

A-8025-235-A (CH)...MBX-49 (CH) ASSY (S) 4-8025-236-A (JP)...MBX-49 (JP) ASSY (S)

Confidential 5-1

5-2

PCG-FX220/FX220K/FX240/FX240K/ PCG-FX250/FX250K/FX270/FX270K (UC)

5-1. Main Section Ref.No. 1 3 3 *8 *8

Part No. X-4623-780-1 4-640-837-31 4-640-837-22 4-651-706-21 4-651-706-01

Description ASSY BOTTOM (AM2) DOOR BATTERY DOOR BATTERY HEATSINK BOTTOM HEATSINK BOTTOM

Ref.No. 71 72 72 74 * 76

Part No. 4-641-851-02 4-651-709-41 4-651-709-01 4-651-702-11 4-644-361-01

* 11 * 11 12 15 15

4-651-707-11 4-651-707-21 1-763-658-21 4-643-832-31 4-643-832-21

INSULATOR HEATSINK BOTTOM INSULATOR HEATSINK BOTTOM FAN, DC (WITH HEAT SINK) DUMMY CARD DUMMY CARD

* 78 * 78 81

18 18 19 20 21

A-8025-266-A A-8066-695-A X-4623-388-2 1-529-287-11 3-718-233-01

SWX-73 (CH) ASSY (S) COMPLETE PWB SWX-73CH ASSY HOOD KEYBOARD (Z) SPEAKER UNIT NUT, PLATE

4-644-362-21 PLATE PALMREST 4-644-362-11 PLATE PALMREST 8-749-019-00 IC HYM71V16M655AT6-P (PC-100 SO-DIMM (128MB CL2)) 8-749-019-29 IC MC-4516CD641PS-A80 (PC-100 SO-DIMM (128MB CL2)) 8-749-018-97 (FX270/FX270K)...

IC HYM71V8M655AT6-P (PC-100 SO-DIMM (64MB CL2))

22 24

1-790-639-22 FPC 50PIN (FOR HDD) 1-772-727-11 (FX250/FX250K/FX270/FX270K)...

HDD (DJSA-220 20.0GB) 1-796-187-11 (FX220/FX220K/FX240/FX240K)...

HDD (15.0GB)-DJSA220 1-476-647-12 KEY BOARD UNIT (US) X-4623-390-1 ASSY PALMREST

24 25 26 27 28 28 29 * 30 31 32 32 33 33

1-772-529-72 A-8025-267-A A-8066-693-A 4-651-699-01 4-651-708-21

PAD, TOUCH CNX-125 (CH) ASSY (S) COMPLETE PWB CNX-125CH BRACKET PAD BRACKET (HDD)

4-640-861-11 BRACKET CD-ROM R 1-796-171-11 (FX220/FX220K)...

DVD-ROM DRIVE (SDR-081) 1-796-072-12 (FX240/FX240K/FX250/ FX250K/FX270/FX270K)...

COMBO DRIVE (UJDA710) X-4623-749-1 (FX220/FX220K)...

ASSY DOOR DVD-RW Q (EXP) X-4623-442-1 (FX240/FX240K/FX250/ FX250K/FX270/FX270K)...

ASSY DOOR DVD-RW PA (EXP)

34 35 36 37 38

4-640-860-12 4-640-828-01 1-772-034-21 X-4623-528-1 4-651-713-11

BRACKET (CD-ROM L) PLATE FDD FDD (FD-5HG-5760) ASSY BOTTOM FDD Z (TCY2) (CH)...DOOR (IO)

38 39 40 41 46

4-651-713-01 4-651-844-01 4-651-714-21 4-640-851-11 A-8025-233-A

(JP)...DOOR I/O FOOT REAR DOOR DOCKING CONNECTOR FOOT FRONT (CH)...PWS-13 (CH) ASSY (S)

46 48 52 53 55

A-8025-234-A 1-761-380-23 1-790-640-11 1-790-641-11 4-640-845-11

(JP)...PWS-13 (JP) ASSY (S) CARD, MODEM FPC 50PIN (FOR CD-ROM) FPC 50PIN (FOR FDD) BUTTON BAY

56 * 57 * 58 * 59 60

4-644-349-01 4-640-854-01 4-651-850-01 4-640-857-01 4-651-698-21

LATCH BAY SPRING BAY BRACKET BOTTOM DOOR BATTERY SPRING DISPLAY BASE

63 67 67 68 69

4-651-928-01 4-652-099-21 4-652-099-01 4-641-629-01 4-641-763-21

COVER BATTERY CONNECTOR (CH)...LABEL I/O (JP)...LABEL I/O INSULATOR FDD LABEL FD

81 82

82

Description SPRING (FDD), PLATE (CH)...BRACKET IO (JP)...BRACKET IO DOOR DIMM BRACKET SPK

84 88 88 105

8-759-695-59 (FX270/FX270K)...

IC MT4LSDT864HG-10EB1 (PC-100 SO-DIMM (64MB CL2)) 1-960-827-21 HARNESS (2 PIN) A-8025-235-A (CH)...MBX-49 (CH) ASSY (S) A-8025-236-A (JP)...MBX-49 (JP) ASSY (S) 4-641-630-11 COVER BAY HOLE

112 123 124 125 126

1-815-505-12 1-790-711-21 1-757-767-11 1-790-710-11 4-644-053-01

CONNECTOR,2 SLOT CARD BUS FFC (PPK) FFC (TP-CNX) FFC (SWX-PWS) SPACER FDD

* 128 * 134 136 139 147

4-653-452-01 4-645-433-01 4-644-357-01 A-8048-966-A 6-700-620-01

PLATE, GROUND BRACKET BAY CONNECTOR CUSHION SPK ASSY BAY FD (TE) (FX220/FX220K)...

IC KP80526GY750256-2 (PIII 750 MHz)

147 147 148 * 152 153

Ref.No. B1 B3 B4 B6 B7

Part No. 4-641-726-41 4-644-899-01 4-639-112-01 4-646-807-01 4-644-402-12

Description SCREW (M2), SPECIAL HEAD SCREW (M2), 0 NUMBER P3 KIND SCREW M2X4 0 PLATE M2.5 (FDD) SCREW (MBX)

B10 B12 B14 B15 B18

4-652-498-01 4-645-177-01 4-645-497-01 4-635-301-01 4-635-966-01

+B M2 SCREW SCREW SCREW SCREW

(NOJI) (M1.7X3.5) (M2.6), CROSS (HOLE) BIND M3X4 (HEX)

B31 B32 B33 B34 B35

4-645-214-11 7-621-772-68 4-642-852-21 4-641-726-11 7-621-772-70

GRIP, SCREW +B M2 SCREW SCREW

M2 +B 2X12

B36 B37

7-622-205-05 NUT (M2 TYPE2), HEXAGON 4-650-481-01 SCREW (B1.7), TAPPING

(M2), SPECIAL HEAD +B 2X14

6-700-619-01 (FX240/FX240K/FX250/FX250K)...

IC KP80526GY800256-2 (PIII 800 MHz) 6-700-618-01 (FX270/FX270K)...

IC KP80526GY850256-2 (PIII 850 MHz) X-4623-561-2 ASSY LATCH DETECTOR 4-651-871-01 HEAT SINK 4-652-012-01 SHEET, ELECTRIC HEAT

154 155 156 157 159

4-651-989-01 4-651-701-11 4-653-151-11 4-653-466-01 4-653-963-01

SPACER (MBX) DOOR MODEM SPACER (KBF) CUSHION (HD-M) SHIELD (CNX)

160 161 162 163 164

4-653-964-01 4-654-019-01 4-654-047-01 4-653-936-01 1-779-745-21

SPACER (B/P) GASKET (AV) SHIELD (AV) GASKET (HB/M) JACK, DC

165 166 167 169 170

1-815-422-11 1-695-514-21 1-815-221-21 4-653-962-01 4-644-667-11

USB CONNECTOR (VERTICAL) JACK (SMALL TYPE) 1P CONNECTOR, USB (VERTICAL) SHIELD (USB) COVER RJ-11

170 171 184

4-644-667-01 COVER RJ-11 4-654-350-11 SHEET (CPU), THERMAL 4-654-776-01 INSULATOR (SCREW)

Confidential PCG-FX220/FX220K/FX240/FX240K/ PCG-FX250/FX250K/FX270/FX270K (UC)

5-3

5-4

B34

B1 B1

B33 B1 128 156

B3

B1 22

I J

G

30 J B32

B15 B3

A 25

K

G B1

B15

N

60

B1

B34

19

63 24 B34

B34

12

H

171 15

169

B1 B10

20

153 B34

26

136

148 82

152

(FX220/FX220K Model) 27

21

B34

147

C

F

46

L B7

B10

125

124

31

18

76

H

B37

34

28

136

29 88

112

N

123

B4

164

166

B4

72

165 K I

20

B18

B36

B18

32

B10

76

157

33

B1 B4 B10 L

B34

C

31

B10

71 167 11

159

B34 84 52

48

134 E

58

57

161

B10 34

162 B34

B31

56

B3

163

B14

(FX240/FX240K/FX250/FX250K/ FX270/FX270K Model)

B

A

33

32 B12

38

69

59

not supplied

B12

B34

170

B35 81

78 D

154

B 67 184

160 3

126 D 53

B14

E

35

F

68

36

1 39

8 B3

701 (Refer to Page 5-12)

B6

B3 105

74

41 55 B34

37

155 B6

40 B34

139

Confidential 5-5

5-6

PCG-FX220/FX220K/FX240/FX240K/ PCG-FX250/FX250K/FX270/FX270K (UC)

5-2. LCD Section (FX270/FX270K Model) – Made by HI – 226 224 234

B30

203

B22

235

206 234

208

B22

224

Ref.No. 201 202 203 206 207

Part No. 1-476-316-11 X-4623-380-1 X-4623-690-1 4-637-902-41 1-476-300-11

Description INVERTER UNIT HINGE LEFT 15 ASSY HOU,BEZEL 15H-Z (EXP) LATCH ASSY LCD 15SXGA (HI) (S)

208 212 213 214 214

4-637-903-01 X-4623-689-1 4-642-762-41 4-655-380-11 4-655-380-51

SPRING LATCH ASSY HOU,DISPLAY 15H-Z (EXP) COVER HINGE (15) (FX270)...LABEL ID (U) (FX270K)...LABEL ID (U)

219 * 220 * 221 * 222 223

1-757-604-11 4-647-506-01 4-647-508-11 4-647-507-01 1-961-017-11

PWB, FLEXIBLE PRINT (SINGLE) BRACKET LCD (L) 15SX BRACKET LCD (LR) SX BRACKET LCD (R) 15SX HARNESS, LCD (SXGA+)

224 225 226 228 229

4-646-217-11 4-635-277-22 4-643-549-12 X-4623-381-1 4-643-366-11

COVER SCREW SIDE (15) COVER SCREW LOWER COVER SCREW SHAFT HINGE RIGHT 15 EDGE GUARD HINGE (15)

234 235

4-635-276-22 COVER SCREW UPPER 4-642-760-12 CUSHION CENTER

207

Ref.No. B8 B22 B23 B30

FILAMENT TAPE (W12X50)(∗1)

236

∗1 : Use the FILAMENT TAPE.

NOTE : B23

Set the DIP switch on the MBX-49 board (Main board) to match with the LCD (1-476-300-11) that is used in this computer.

221

O N

∗1 236∗1

223

1 2 3 4 5 6 7 8

B8

220 222 202

The upper position where ON indication is shown is the ON position . The lower position is the OFF position.

229

219

213 B23

1 2 3 4 5 6 7 8 ON/OFF 0 0 0 0 0 1 1 1 No.

214

0 : ON

B23

1: OFF

221 201 212

B8 225

213

228

∗1 For the installation position, refer to page 5-5.

Confidential PCG-FX220/FX220K/FX240/FX240K/ PCG-FX250/FX250K/FX270/FX270K (UC)

5-7

5-8

Part No. 4-641-726-11 4-641-726-81 4-644-165-01 4-643-550-01

Description SCREW (M2), SPECIAL HEAD SCREW (M2), SPECIAL HEAD SCREW (M2.6X4), 0 PLATE P1 MAIN +P 2.6X6 LOCK PRECISION TYPE3

5-3. LCD Section (FX220/FX220K/FX250/FX250K Model) – Made by HI – 426 424 434

B30

403

B22

435

406 434

408

B22

424

407

Ref.No. 401 402 403 406 407

Part No. 1-476-316-11 X-4623-380-1 X-4623-690-1 4-637-902-41 1-476-186-12

Description INVERTER UNIT HINGE LEFT 15 ASSY HOU,BEZEL 15H-Z (EXP) LATCH ASSY LCD 15HI (S)

408 412 413 414 414

4-637-903-01 X-4623-689-1 4-642-762-41 4-655-380-41 4-655-380-81

SPRING LATCH ASSY HOU, DISPLAY 15H-Z (EXP) COVER HINGE (15) (FX220)...LABEL ID (U) (FX220K)...LABEL ID (U)

414 414 419 * 420 * 421

4-655-380-21 4-655-380-61 1-757-604-11 4-647-506-01 4-647-508-11

(FX250)...LABEL ID (U) (FX250K)...LABEL ID (U) PWB, FLEXIBLE PRINT (SINGLE) BRACKET LCD (L) 15SX BRACKET LCD (LR) SX

* 422 423 424 425 426

4-647-507-01 1-961-018-11 4-646-217-11 4-635-277-22 4-643-549-12

BRACKET LCD (R) 15SX HARNESS, LCD (XGA-F-N) COVER SCREW SIDE (15) COVER SCREW LOWER COVER SCREW SHAFT

428 429 434 435 437

X-4623-381-1 4-643-366-11 4-635-276-22 4-642-760-12 4-643-837-01

HINGE RIGHT 15 EDGE GUARD HINGE (15) COVER SCREW UPPER CUSHION CENTER SHIELD (LCD)

Ref.No. B8 B22 B23 B30

Part No. 4-641-726-11 4-641-726-81 4-644-165-01 4-643-550-01

Description SCREW (M2), SPECIAL HEAD SCREW (M2), SPECIAL HEAD SCREW (M2.6X4), 0 PLATE P1 MAIN +P 2.6X6 LOCK PRECISION TYPE3

FILAMENT TAPE (W12X50)(∗1)

438

∗1 : Use the FILAMENT TAPE.

B23

437 421

NOTE :

∗1 437 B8

423

O N

438∗1

Set the DIP switch on the MBX-49 board (Main board) to match with the LCD (1-476-186-12) that is used in this computer.

422 402

1 2 3 4 5 6 7 8

420 429

419

The upper position where ON indication is shown is the ON position . The lower position is the OFF position.

413 B23 414

1 2 3 4 5 6 7 8 ON/OFF 0 0 0 0 1 1 1 1 No.

B23 421

0 : ON

1: OFF

401 412

B8 425

413

428

∗1 For the installation position, refer to page 5-5.

Confidential 5-9

5-10

PCG-FX220/FX220K/FX240/FX240K/ PCG-FX250/FX250K/FX270/FX270K (UC)

5-4. LCD Section (FX240/FX240K Model) – Made by HI – 303 325

304

305

B8 B8

Ref.No. 301 302 303 304 305

Part No. 1-476-316-11 X-4623-378-1 X-4623-775-1 4-635-277-22 4-635-276-22

Description INVERTER UNIT HINGE LEFT MV ASSY HOU, BEZEL 14H-Z (EXP) COVER SCREW LOWER COVER SCREW UPPER

306 307 308 309 312

4-637-902-41 1-476-789-11 4-637-903-01 X-4623-379-1 X-4623-693-1

LATCH LCD UNIT (14XGA HITACHI) SPRING LATCH HINGE RIGHT MV ASSY HOU, DISPLAY 14SA-Z (EXP)

313 314 314 317 319

4-642-762-41 4-655-380-31 4-655-380-71 1-757-605-11 4-654-966-01

COVER HINGE (15) (FX240)...LABEL ID (U) (FX240K)...LABEL ID (U) PWB, FLEXIBLE PRINT (SINGLE) SHEET (BEZEL), ADHESIVE

* 322 * 323 325 326

4-644-163-01 4-644-164-01 4-642-760-12 1-961-018-31

BRACKET LCD LEFT 14 (SA) BRACKET LCD RIGHT 14 (SA) CUSHION CENTER HARNESS, LCD (XGA-F-N)

Ref.No. Part No.

701 0702 703 703 704 0

319 306

B22 B8

314 307

322

B8 B20 B22

308

Description ACCESSORIES ************

A-8048-965-A ASSY WEIGHT SAVER (Z) (Refer to P.5-4) 1-476-342-21 ADAPTOR, AC 1-528-935-21 (FX250/FX250K/FX270/FX270K)...

BATTERY PACK, LITHIUM ION 1-756-147-11 (FX220/FX220K/FX240/FX240K)...

BATTERY PACK, LITHIUM ION 1-575-875-51 CORD, CONNECTION 1-757-562-21 CORD,POWER 4-655-567-11 QUICK START FX200SERIES

701

703

Weight saver (1)

Battery pack (1)

702

704

AC adaptor (1)

Video cable (1)

4-641-726-11 SCREW (M2), SPECIAL HEAD 7-628-254-00 SCREW +PS 2.6X5 4-642-761-01 +P M2X3 LOCK

B8 B20

302 323

NOTE :

B8

Set the DIP switch on the MBX-49 board (Main board) to match with the LCD (1-476-789-11) that is used in this computer.

∗1 B8

O N

B8 B20 326

309

B8

1 2 3 4 5 6 7 8

B22

The components identified by mark 0 or dotted line with mark 0 are critical for safety.

Replace only with part number specified.

The upper position where ON indication is shown is the ON position . The lower position is the OFF position.

1 2 3 4 5 6 7 8 ON/OFF 0 0 1 0 0 1 1 1 No.

317

0 : ON

301

1: OFF

313

312

313

∗1 For the installation position, refer to page 5-5.

Confidential PCG-FX220/FX220K/FX240/FX240K/ PCG-FX250/FX250K/FX270/FX270K (UC)

5-11

5-12

Les composants identifiés par une marque 0 sont critiques pour la sécurité.

Ne les remplacer que par une pièce portant le numéro spécifié.

5-5. Connector Section

Ref.No. 72

Fig.

Part No.

Description

4-651-709-41 (CH)...BRACKET IO 4-651-709-01 (JP)...BRACKET IO I/O BRACKET

72

164

1-779-745-21 JACK, DC DC IN connector

164 165

165

1-815-422-11 CONNECTOR (VERTICAL) USB connector

167

1-815-221-21 CONNECTOR, USB (VERTICAL) USB connector

167

∗Before replacing the connector of reference number 164, 165 and 167, remove the I/O bracket.

For the disassembling procedure, refer to page 1-17.

167

72 165

164

165 167

164

5-13

Confidential 5-14 (END)

PCG-FX220/FX220K/FX240/FX240K/ PCG-FX250/FX250K/FX270/FX270K (UC)

PCG-FX220/FX220K/FX240/FX240K/ PCG-FX250/FX250K/FX270/FX270K (UC)

List of PCG-FX Series (As of May, 2001) Model Name

Service Manual Part No.

PCG-FX290K PCG-FX290

9-872-209-11

PCG-FX190K PCG-FX170K PCG-FX150K

9-872-194-11

PCG-FX140K PCG-FX120K PCG-FX190 PCG-FX170 PCG-FX150

9-872-179-11

PCG-FX140 PCG-FX120 PCG-FX270K PCG-FX270 PCG-FX250K PCG-FX250 PCG-FX240K

9-872-227-11

PCG-FX240 PCG-FX220K PCG-FX220 PCG-FX210

9-872-204-11

PCG-FX215

9-872-232-11 : Additional Models

This manual and the constituent data may not be replicated, copied nor reprinted in whole or in part without prior written authorization of Sony Corporation.

9-872-227-11

Sony Corporation

— 50 —

English 2001E1600-1 © 2001 Sony Corporation Published by MNC IT Planning & Control Dept. [SODP]