Parker Motor Pump Series F11 F12 Parts Manual HY17-8249-US - PDF DOWNLOAD

Hydraulic Motor/Pump Series F11/F12 Fixed Displacement

zp11

Catalogue HY17-8249/US March 2004

zp12

Conversion

factors

1 kg ............................................................... 2.20 lb 1 N .............................................................. 0.225 lbf 1 Nm ........................................................ 0.738 lbf ft 1 bar ............................................................. 14.5 psi 1 l .................................................... 0.264 US gallon 1 cm 3 ....................................................... 0.061 cu in 1 mm ........................................................... 0.039 in 9/ °C + 32 .......................................................... 1 °F 5

Hydraulic motor/pump Series F11/F12

Catalogue HY17-8249/US

Content Content

Page

General information ................................................ 4 F11 cross section ................................................... 4 F12 cross sections ................................................. 5 Specifications ......................................................... 6 Ordering codes F11-CETOP ............................................................ 7 F11-ISO .................................................................. 8 F11-SAE ................................................................. 9 F12-ISO ................................................................ 10 F12-Cartridge ....................................................... 11 F12-SAE ............................................................... 12 Prefered versions F11/F12 ................................... 13 Technical information Bearing life ........................................................... 14 Bearing life calculation .......................................... 14 Required information ............................................ 14 Noise level ............................................................ 15 Efficiency .............................................................. 15 Selfpriming speed and required inlet pressure ..... 16 Installation dimensions F11-5 CETOP ....................................................... 17 F11-10 CETOP ..................................................... 18 F11-14 CETOP ..................................................... 19 F11-19 CETOP ..................................................... 20 F11-14 ISO ........................................................... 21 F11-14 SAE .......................................................... 22 F11-19 SAE .......................................................... 23 F12-30, -40, -60, -80 and -110 ISO ................ 24-25 F12-30, -40, -60, -80 and -110 Cartridge ........ 26-27 F12-30, -40, -60, -80 and -110 4 bolt flange .... 28-29 F12-30, -40, and -60 2 bolt flange ................... 30-31 F11-150 CETOP ................................................... 32 F11-150 SAE ........................................................ 33 F11-250 SAE ........................................................ 34 Technical information F11 saw motors .................................................... 35 F11 fan motors ..................................................... 35 F12 integrated flushing valve ................................ 36 F12 accessory valve blocks .................................. 36 Type BT brake valve ............................................. 37 Type SR pressure relief/make-up valve ................ 37 Type SV pressure relief valve ............................... 38 Speed sensor ....................................................... 38 F12 main port suction fittings ............................... 39 Suction fittings ...................................................... 39 Suction fitting kits ................................................. 39 Split-flange kits ..................................................... 39 Installation information ......................................... 40 Direction of rotation .............................................. 40 Hydraulic fluids ..................................................... 40 Operating temperature ......................................... 40 Installation information Viscosity ............................................................... 41 Filtration ............................................................... 41 Case pressure ...................................................... 41 Case drain connections ........................................ 42 Before start-up ..................................................... 42 3

Parker Hannifin Mobile Controls Division Trollhättan, Sweden

Hydraulic motor/pump Series F11/F12

Catalogue HY17-8249/US

General information F11 and F12 are bent axis, fixed displacement heavyduty motor/pump series. They can be used in numerous applications in both open and closed loop circuits.

• Series F11 is available in the following frame sizes and versions: - F11-5, -10, -14, 19 and -150 with CETOP mounting flange and shaft end - F11-14 with ISO flange and shaft - F11-14, -19, -150 and -250 with SAE flange and shaft • Series F12 conforms to current ISO and SAE mounting flange and shaft end configurations. A very compact cartridge version is also available.

• Thanks to the unique spherical piston design, F11/F12 motors can be used at unusually high shaft speeds.

Operating pressures to 480 bar provides for the high output power capability.

• The 40° angle between shaft and cylinder barrel allows for a very compact, lightweight motor/pump.

F11 cross section

1

2

• The laminated piston ring offers important advantages such as low internal leakage and thermal shock resistance.

• The pump version has highly engineered valve plates for increased selfpriming speed and low noise, available with left and right hand rotation.

• The F11/F12 motors produce very high torque at start-up as well as at low speeds.

• Our unique timing gear design synchronizes shaft and cylinder barrel, making the F11/F12 very tolerant to high 'G' forces and torsional vibrations.

• Heavy duty roller bearings permit substantial external axial and radial shaft loads.

• The F11's and F12's have a simple and straightforward design with very few moving parts, making them very reliable motors/pumps.

• The unique piston locking, timing gear and bearing set-up as well as the limited number of parts add up to a very robust design with long service life and, above all, proven reliability.

3

4

5

6

7

8

1. Barrel housing 2. Valve plate 3. Cylinder barrel 4. Guide spacer with O-rings 5. Timing gear 6. Roller bearing 7. Bearing housing 8. Shaft seal 9. Output/input shaft 10. Piston with laminated piston ring

10

4

Parker Hannifin Mobile Controls Division Trollhättan, Sweden

9

Hydraulic motor/pump Series F11/F12

Catalogue HY17-8249/US

General information F12 cross sections F12-30, -40, -60 and -80 (F12-60 shown)

2

1

Legend:

F12-110

1.

2.

3.

4.

Barrel housing Valve plate Cylinder barrel Piston with piston ring

1

2

4

3

5.

6.

7.

8.

3

5

6

Timing gear Tapered roller bearings Bearing housing Shaft seal

10

4

5

9

8

7

9. Output/input shaft 10. Port E (F12-110) 11. Needle bearings (F12-110)

6

7

8

9

11 5

Parker Hannifin Mobile Controls Division Trollhättan, Sweden

Hydraulic motor/pump Series F11/F12

Catalogue HY17-8249/US

Specifications Frame size F11-5 Displacement [cm3/rev] [cu in/rev]

4.9 0.30

Operating pressure max intermittent1) [bar] [psi] max continuous [bar] [psi]

420 6 000 350 5 000

-10

-14

-19

F12-30 -40

9.8 0.60

14.3 0.87

19.0 1.16

30.0 1.83

40.0 2.44

-60

-80

59.8 3.65

80.4 110.1 4.91 6.72

420 480 6 000 7 000 350 420 5 000 6000

-110 F11-150 -250 150 9.15

242 14.8

480 420 420 7 000 6 000 6 000 420 350 350 6000 5 000 5 000

Motor operating speed [rpm] max intermittent1) 12 000 11 000 10 000 9 000 7 100 6 400 5 600 5 200 4 700 3 000 2 700 max continuous 10 800 9 900 9 000 8 100 5 600 5 000 4 300 4 000 3 600 2 600 2 400 min continuous 50 50 Max pump selfpriming speed2) L or R function; max [rpm] 4 600 4 200

3 900

3 500

3150 2870 2500 2300 2290

143 37.8 128 33.8

171 45.2 153 40.4

213 56.3 168 44.4

Motor input flow max intermittent1) [l/min] [gpm] max continuous [l/min] [gpm]

58 15.3 52 13.7

Main circuit temp.3), max [°C] [°F] min [°C] [°F]

80 175 -35 -31

-35 -31

-30 -22

-35 -31

-35 -31

Mass moment of inertia (x10-3) [kg m2] (x10-2) [lbft2]

0.16 0.38

0.39 0.92

0.42 1.00

1.1 2.61

1.7 4.03

5 11

7.5 16.5

8.3 18.8

11 24

12 26

Weight [kg] [lb]

108 28.5 97 25.6

256 67.6 200 52.8

1 700 1 500

335 418 517 450 650 88.5 110.4 136.6 119.0 172.8 257 322 396 390 580 67.9 85.1 104.6 103.0 153.6

-35 -31

-35 -31

2.9 5 8.4 11.2 40 46 6.88 11.86 19.93 26.58 94.92 109.16 16.5 36

21 46

26 57

36 79

70 154

1) Intermittent: max 6 seconds in any one minute.

2) Selfpriming speed valid at sea level.

3) See also installation information, operating temperature.

Basic formulas for hydraulic motors Flow (q) q = Dxn

1000 x ηv

[l/min]

displacement [cm3/rev] shaft speed [rpm] volumetric efficiency differential pressure [bar] (between inlet and outlet) ηhm - mechanical efficiency ηt - overall efficiency (ηt = ηv x ηhm) D n ηv ∆p

Torque (M) M =

D x ∆p x ηhm [Nm] 63

Power (P) P =

q x ∆p x ηt [kW] 600

6

80 175 -35 -31

-

Parker Hannifin Mobile Controls Division Trollhättan, Sweden

77 170

Hydraulic motor/pump Series F11/F12

Catalogue HY17-8249/US

Ordering codes F11

—

Pump

— Frame size

Motor

—

—

Function Main ports

Mounting Shaft flange seal

— Shaft

—

—

Version number

Option page 36

Option page 38

F11-CETOP Frame size Code Displacem. (cm3/rev) 5 4.9 10 9.8 14 14.3 19 19.0 150 150.0

Frame size Code Function M Motor H Motor, high pressure Q Motor, silent J Motor, clockwise rot'n 1) G Motor, counter clockw.1) R Pump, clockwise rot'n L Pump, counter clockw.

Frame size Code Main ports B BSP threads R With anti-cavitation valve; clockwise rot’n2) L With anti-cavitation valve; counter clockw.2) U SAE, UN threads F SAE 6000 psi flange

Version number (assigned for special versions)

Option None 5

10

14

x x (x) (x) (x) x x

x x (x) (x) (x) x x

x x x

5

10

14

x

x

x

x

-

-

x

x

x

-

(x) -

x (x) -

x -

x (x) -

x

Frame size Code Mounting flange C CETOP flange W Saw motor flange

x: 1) 2) 3) 4)

Available (x): Optional Internal drain BSP threads NBR - Nitrile rubber FPM - Fluor rubber

19 150 x x (x) (x) (x) x x

x x (x) (x) (x) x x

Frame size 5 10 14 19 150 Code Shaft K Metric key x x x x x D Spline, DIN 5480 (x) (x) (x) (x) (x)

19 150

5

10

14

x -

x x

x x

Frame size Code Shaft seal N NBR3), low pressure H NBR3), high pressure E FPM4), low pressure, high temperature V FPM4), high pressure, high temperature

10

14

x x

x x

-

x x

x x

x

x

x

x

x

-

x

x

x

-

Frame size Code Option S With speed sensor P Prepared for speed sensor

19 150 x x

5

x -

19 150

5

10

14

-

-

x

x

-

-

-

x

x

-

– : Not available

7

Parker Hannifin Mobile Controls Division Trollhättan, Sweden

19 150

Hydraulic motor/pump Series F11/F12

Catalogue HY17-8249/US

Ordering codes F11

—

Pump

— Frame size

Motor

— Function Main ports

— Mounting Shaft flange seal

— Shaft

— Version number

— Option page 36

Option page 38

F11-ISO Frame size Code Displacem. (cm3/rev) 14 14.3

Frame size Code Function H Motor, high pressure R Pump, clockwise rot'n L Pump, counter clockw.

Version number (assigned for special versions)

Frame size 14 Code Shaft K Metric key x D Spline, DIN 5480 (x)

14 x x x

Frame size Code Main ports F SAE 6000 psi flange

14 x

Frame size Code Mounting flange I ISO flange

x: Available (x): Optional 1) FPM - Fluor rubber

Frame size Code Shaft seal E FPM1), low pressure, high temperature V FPM1), high pressure, high temperature

Option None

14

x x

Frame size Code Option S With speed sensor P Prepared for speed sensor

14 x

– : Not available

8

Parker Hannifin Mobile Controls Division Trollhättan, Sweden

14 x x

Hydraulic motor/pump Series F11/F12

Catalogue HY17-8249/US

Ordering codes F11 Pump Motor

—

— Frame size

—

—

Function Main ports

Mounting Shaft flange seal

— Shaft

— Version number

— Option page 36

Option page 38

F11-SAE Frame size Code Displacem. (cm3/rev) 14 14.3 19 19.0 150 150.0 250 242.0

Version number (assigned for special versions)

Option None Frame size Code Function M Motor H Motor, high pressure Q Motor, silent J Motor, clockwise rot'n 1) G Motor, counter clockw.1) R Pump clockwise rot'n L Pump counter clockw.

14 x x x

19 150 250 x x (x) (x) (x) x x

Frame size Code Main ports U SAE, UN threads B BSP threads F SAE 6000 psi flange2) R With anti-cavitation valve; clockwise rot’n3) L With anti-cavitation valve; counter clockw.3)

Frame size Code Mounting flange S SAE flange

x: 1) 2) 3) 4) 5)

Available (x): Optional Internal drain Metric thread BSP threads NBR - Nitrile rubber FPM - Fluor rubber

x x (x) (x) (x) x x

14

x x x

Frame size 14 19 150 250 Code Shaft T SAE key x x x S SAE spline (x) (x) (x) (x) K Metric key x F SAE spline (x)

19 150 250

x -

x (x) -

x

x

x

x

-

-

x

x

-

-

14 x

Frame size Code Shaft seal N NBR4), low pressure H NBR4), high pressure E FPM5), low pressure, high temperature V FPM5), high pressure, high temperature

x

19 150 250

-

x x

x x

x x

x

x

x

x

x

x

-

-

Frame size Code Option S With speed sensor P Prepared for speed sensor

19 150 250 x

14

x

14

19 150 250

x

x

-

-

x

x

-

-

– : Not available

9

Parker Hannifin Mobile Controls Division Trollhättan, Sweden

Hydraulic motor/pump Series F11/F12

Catalogue HY17-8249/US

Ordering codes F12

—

—

—

Frame size

Function Main ports

— Mounting Shaft flange seal

— Shaft

—

—

Version number

Option page 36

Option page 38

F12-ISO Frame size Code Displacem. (cm3/rev) 30 30.0 40 40.0 60 59.8 80 80.4 110 110.1

Frame size Code Function M Motor Pump: L counter clockw.

R clockwise

Version number (assigned for special versions)

Frame size Code Shaft D DIN spline Z K Metric key P

30 40 60 x

x

x

x

x x

x x

x x

x x

x x

30 40 60 x

Standard x x Optional (x) (x) Standard x x Optional (x) -

x x - (x) x x - -

x x -

80 110

x

Frame size Code Main ports F ISO flange

30 40 60 80 110

x

x

Frame size Code Option L01 Integr. flushing valve

x

Frame size 30 40 60 80 110 Code Mounting flange I ISO flange x x x x x

40

60

x

x

x

Frame size Code Option S With speed sensor P Prepared for speed sensor

80 110 x

30

Frame size Code Shaft seal H NBR 1), high pressure N NBR 1), low pressure V FPM2), high temperature, high pressure

30

40

60

x x x

x x x

x x x

80 110 -3)

x

30

40

60

x

x

x

x

x

x

x

x

x

x

80 110 x x x

x x x

x : Available (x) : Optional – : Not available 1) NBR - Nitrile rubber 2) FPM - Fluor rubber 3) F12-110: Accessory valve block (page 36)

10

Parker Hannifin Mobile Controls Division Trollhättan, Sweden

80 110

Hydraulic motor/pump Series F11/F12

Catalogue HY17-8249/US

Ordering codes F12

—

—

—

Frame size

Function Main ports

— Mounting Shaft flange seal

— Shaft

—

—

Version number

Option page 36

Option page 38

F12-Cartridge Frame size Code Displacem. (cm3/rev) 30 30.0 40 40.0 60 59.8 80 80.4 110 110.1

Frame size Code Function M Motor

Version number (assigned for special versions)

Frame size 30 40 60 80 110 Code Shaft C DIN spline Standard x x x x x K Metric key Standard x x x X " " Optional - (x) - -

30 40 60 x

Frame size Code Main ports F ISO flange

x

x

80 110 x

x

30 40 60 x

x

Frame size Code Option L01 Integr. flushing valve

x

x

Frame size 30 40 60 80 110 Code Mounting flange C Cartridge x x x x x

40

60

x

x

x

Frame size Code Option S With speed sensor P Prepared for speed sensor

80 110 x

30

Frame size 30 Code Shaft seal H NBR1), high pressure x N NBR1), low pressure x V FPM2) high temperature, x high pressure)

40

60

x x x

x x x

80 110 -3)

x

30

40

60

x

x

x

x

x

x

x

x

x

x

80 110 x x x

x x x

x : Available (x) : Optional – : Not available 1) NBR - Nitrile rubber 2) FPM - Fluor rubber 3) F12-110: Accessory valve block (page 36)

11

Parker Hannifin Mobile Controls Division Trollhättan, Sweden

80 110

Hydraulic motor/pump Series F11/F12

Catalogue HY17-8249/US

Ordering codes F12

—

— Frame size

— Function

Main ports

— Mounting Shaft flange seal

— Shaft

—

—

Version number

Option page 36

Option page 38

F12-SAE Frame size Code Displacem. (cm3/rev) 30 30.0 40 40.0 60 59.8 80 80.4 110 110.1

Frame size Code Function M Motor Pump: L counter clockw.

R clockwise

Version number (assigned for special versions)

Frame size Code Shaft S SAE spline Standard U " " Optional T SAE key Standard

30 40 60

30

40

60

x x

x x

x x

80 110 x (x) x

x x

80 110

x

x

x

x

x

x x

x x

x x

x x

x x

Frame size Code Option L01 Integr. flushing valve

40

60

x

x

x

x

30

40

60

x

x

x

x

x

x

x

x

x

x

Frame size Code Option S With speed sensor P Prepared for speed sensor

Frame size 30 40 60 80 110 Code Main ports S SAE flange x x x x x U SAE, UN threads (x) (x) (x) - (x)

Frame size 30 40 60 80 110 Code Mounting flange S SAE 4 bolt x x x x x T SAE 2 bolt x x x - -

30

Frame size Code Shaft seal H NBR1), high pressure N NBR1), low pressure V FPM2), high temperature, high pressure

30

40

60

x x x

x x x

x x x

80 110 -3)

80 110 x x x

x x x

x : Available (x) : Optional – : Not available 1) NBR - Nitrile rubber 2) FPM - Fluor rubber 3) F12-110: Accessory valve block (page 36)

12

Parker Hannifin Mobile Controls Division Trollhättan, Sweden

80 110

Hydraulic motor/pump Series F11/F12

Catalogue HY17-8249/US

Ordering codes Prefered versions F11/F12 catalogue F11 Ordering Codes F11-005-MB-CN-K F11-005-MB-CH-K F11-005-HU-CH-K F11-010-MB-CN-K F11-010-MB-CH-K F11-010-HU-CH-K F11-014-HB-CE-K F11-014-HB-CV-K F11-019-MB-CN-K F11-019-MB-CH-K F11-150-MF-CN-K F11-150-MF-CH-K F11-150-HF-SH-S F11-250-QF-SH-F F11-250-QF-SH-K

Part number 3703665 3707249 3707308 3703603 3706030 3707310 3783201 3782830 3703516 3707893 3703468 3707008 3707325 3706440 3795858

F12 Ordering Codes F12-30-MF-IH-D F12-30-MF-IH-K F12-30-MS-SH-S F12-30-MS-TH-S F12-40-MF-IH-D F12-40-MF-IH-K F12-40-MS-SH-S F12-40-MS-SH-T F12-40-MS-TH-S F12-60-MF-IH-D F12-60-MF-IH-K F12-60-MS-SH-S F12-60-MS-TH-S F12-80-MF-IH-D F12-80-MF-IH-K F12-80-MS-SH-S F12-110-MF-IH-D F12-110-MF-IH-K F12-110-MS-SH-S

Part number 3799843 3799844 3799851 3799616 3799525 3799526 3799532 3799533 3799617 3799988 3799989 3799998 3799618 3780767 3780772 3780783 3781530 3781534 3781542

13

Parker Hannifin Mobile Controls Division Trollhättan, Sweden

Hydraulic motor/pump Series F11/F12

Catalogue HY17-8249/US

Technical information Bearing life General information Bearing life can be calculated for that part of the load/ life curve (shown below) that is designated 'Bearing fatigue'. 'Rotating group fatigue and wear' and 'Other' caused by material fatigue, fluid contamination, etc. should also be taken into consideration when estimating the service life of a motor/pump in a specific application.

Bearing life calculations are mainly used when comparing different frame sizes. Bearing life, designated B10 (or L10), is dependent of system pressure, operating speed, external shaft loads, fluid viscosity in the case, and fluid contamination level.

The B10 value means that 90% of the bearings survive, at a minimum, the number of hours calculated. Statistically, 50% of the bearings will survive at least five times the B10 life.

Bearing life calculation An application is usually governed by a certain duty or work cycle where pressure and speed vary with time during the cycle.

In addition, bearing life depends on external shaft forces, fluid viscosity in the case and fluid contamination.

Parker Hannifin (Mobile Controls Division) has a computer program for calculating bearing life and will assist in determining F11 or F12 motor/pump life in a specific application.

Required information When requesting a bearing life calculation from Parker Hannifin (Mobile Controls Division), the following information (where applicable) should be provided: - A short presentation of the application - F11 or F12 size and version - Duty cycle (pressure and speed versus time at given displacements) - Low system pressure - Case fluid viscosity - Life probability (B10, B20, etc.)

- Operating mode (pump or motor) - Direction of rotation (L or R) - External shaft loads - Fixed or rotating radial load - Distance between flange and radial load - Angle of attack (α) as defined below

Life expectancy (logarithmic scale) Other causes

Bearing fatigue

Rotating group fatigue and wear

System pressure

Hydraulic unit life versus system pressure.

F α

F

The direction (a) of the radial load is positive in the direction of rotation as shown.

To obtain maximum bearing life, the radial load should, in most cases, be located approximately at 170° (motor; R.H. rot'n) or 190° (pump; R.H rot'n).

14

Parker Hannifin Mobile Controls Division Trollhättan, Sweden

Catalogue HY17-8249/US

Technical information

Hydraulic motor/pump Series F11/F12

Efficiency

3000 psi 100%

Because of its high overall efficiency, driving a motor/ pump from series F11/F12 requires less fuel or electric power. Also, it allows the use of a small reservoir and heat exchanger, which in turn reduce cost, weight, and installation size.

The diagrams to the right shows volumetric and mechanical efficiencies of an F12-30.

6000 psi 90%

F12-30 (motor)

80% 0

1000

2000

3000

4000

Volumetric efficiency.

Contact Parker Hannifin for efficiency information on a particular F11/F12 frame size that is being considered.

100%

Speed [rpm]

6000 psi 3000 psi

90%

F12-30 (motor)

80% 0

1000

2000

3000

4000

Mechanical efficiency.

Noise level

Speed [rpm]

Noise level [dB(A)]

Series F11/F12 feature low noise levels from low to high speeds and pressures.

As an example, the diagram to the right shows the noise level of an F12-30.

The noise level is measured in a semi-anechoic room, 1 m behind the unit.

The noise level for a particular motor/pump may vary ±2 dB(A) compared to what is shown in the diagram.

90 85 80

5000 rpm 3500 rpm

75

NOTE: Noise information for F11/F12 frame sizes are available from Parker Hannifin.

2000 rpm

70

F12-30 (M, L or R function)

65 0

15

1000

2000

3000

4000

5000 Pressure [psi]

Parker Hannifin Mobile Controls Division Trollhättan, Sweden

Hydraulic motor/pump Series F11/F12

Catalogue HY17-8249/US

Technical information Selfpriming speed and required inlet pressure

Inlet pressure [psi]

Series F11 30 In pump applications, the F11 with function L (counter H F11-19 clockwise rotation) or R (clockwise rotation) is normally used. The L and R (pump) provide the highest self20 priming speeds (see table) as well as the lowest noise M level. The M (motor) function can also be used as a 15 pump, in either direction, but at a lower selfpriming speed.

10 Operating above the selfpriming speed (refer to Diagram 1) requires increased inlet pressure.

L, R As an example, at least 1.0 bar is needed when operat0 ing the F11-19-M as a pump at 3500 rpm. An F11 with 5 in. Hg vacuum H function, used as a motor (e.g. in a hydrostatic transmission), may sometimes operate as a pump at 1000 2000 3000 4000 Speed [rpm] speeds above the selfpriming speed; this requires Diagram 1. Min required inlet pressure (F11-19). additional inlet pressure.

Insufficient inlet pressure can cause pump cavitation resulting in greatly increased pump noise and deterioInlet press. rating performance. [psi]

F12-110 -80 -60 -40 -30

30

Function

L or R

M

H

F11-5 F11-10 F11-14 F11-19 F11-150 F11-250

4600 4200 3900 3500 1700 1500

3800 3100 2400 1300 950

3200 2700 3200 2100 1100 -

F12-L or -R 20

10

Inlet pressure gauge

0

Series F12 When operating the F12 as a pump (with L or R valve plate) above the selfpriming speed, the inlet must be pressurized. Increased noise and deteriorating performance may otherwise be experienced.

Diagrams 2 and 3 show required pump inlet pressure vs. shaft speed.

The F12 motor (type M valve plate) sometimes operates as a pump e.g. when used in a propel transmission and the vehicle is going downhill.

Minimum required inlet pressure versus shaft speed is shown in the diagrams.

5 in. Hg vacuum

1000

2000

3000

4000 Speed [rpm]

Diagram 2. Min. required pump (F12-L or -R) inlet press.

Inlet press. [psi] F12-110 -80 -60 -40 -30 30

F12-M 20

10

0

NOTE: Diagrams 1, 2 and 3 are valid at sea level.

5 in. Hg vacuum

1000

2000

3000

4000 Speed [rpm]

Diagram 3. Min. required motor (F12-M) inlet pressure.

16

Parker Hannifin Mobile Controls Division Trollhättan, Sweden

Hydraulic motor/pump Series F11/F12

Catalogue HY17-8249/US

Installation dimensions F11-5 (CETOP versions)

2.56

3.31 max

0.20

1.50 Main port A BSP ½"

Main port B BSP ½"

1.87 Approx. center of gravity Drain port D BSP ¼"

Drain port C BSP ¼"

0.98 4.47

5.28 max 3.48 2.13

0.31

0.51

R 0.02

R 0.03

0.35

Flange C 1.18

1.57 Key shaft K

0.47 min

Key 6x6

M6*

0.20 Ø0.7090 0.7085

0.81

Ø0.80 min

Ø3.1496 3.1478 * Metric thread 0.35 Ø0.43 (x2)

0.79 2.09 Ø5.00 max

W18x1,25x13x9g Type D spline shaft (DIN 5480)

3.94

40˚ 3.78 max Mounting flange C

17

Parker Hannifin Mobile Controls Division Trollhättan, Sweden

Hydraulic motor/pump Series F11/F12

Catalogue HY17-8249/US

Installation dimensions F11-10 (CETOP versions)

3.70 max

3.11 0.43

1.81 Main port A BSP ¾"

Main port B BSP ¾"

2.09 Approx. center of gravity Drain port D BSP ¼"

Drain port C BSP 3/8"

1.18 5.24

6.14 max 3.98 2.48

0.31

0.55

R 0.02

R 0.03

0.35

Flange C 1.38

1.97 Key shaft K

0.47 min

Key 6x6

M6*

0.28 Ø0.7878 0.7872

0.89

Ø0.91 min

Ø3.9370 3.9349 * Metric thread 0.35 Ø0.51 (x2)

0.87 2.24 Ø5.98 max

W20x1.25x14x9g Spline shaft D (DIN 5480)

4.92

40˚ 4.57 max Mounting flange C

18

Parker Hannifin Mobile Controls Division Trollhättan, Sweden

Hydraulic motor/pump Series F11/F12

Catalogue HY17-8249/US

Installation dimensions F11-14 (CETOP versions)

Main port B (BSP 3/4”-A)

Main port A (BSP 3/4”-A) 4.02

4.02

2.09

2.83

1.81

Speed sensor (optional)

1.77

1.26

Drain port D (BSP 3/8”-A)

Drain port C (BSP 3/8”-A)

25˚

1.18

6.18 max

5.87

5.24 3.94 0.55 0.31 0.37 R 0.02

1.65 1.38

R 0.03

Flange C Type K key shaft

Key 8x7x35 1.02

M8x0.63

Ø0.9744

0.31 Ø0.9846 0.9841 Ø1.06

0.14

1.10 Ø3.9370 3.9349

W 25x1.25x18x9g Type D spline shaft (DIN 5480)

Anticavitation valve (left or right hand optional; right hand shown)

Ø0.51 (x2)

B

2.32

CCW

39˚ (x4)

CW

4.49

A 5.51 5.91 Type C mounting flange

19

Parker Hannifin Mobile Controls Division Trollhättan, Sweden

Hydraulic motor/pump Series F11/F12

Catalogue HY17-8249/US

Installation dimensions F11-19 (CETOP version)

4.49 max

0.43

2.13

Main port A BSP ¾"

2.48

3.46 Main port B BSP ¾"

Drain port C BSP 3/8"

1.14 5.43

Approx. center of gravity Drain port D BSP 3/8" 6.50 max 3.94 0.63

2.28

Flange C 0.91

0.98 1.65 Key shaft K Key 8x7x35

M8*

0.63 min

R 0.04 max

Ø0.9846 0.9841

R 0.05 max

Ø1.11 min Ø4.4094 4.4073

1.10 * Metric thread 0.98

Ø0.55 (x2) 3.42

Ø6.69 max

1.10 5.51

W25x1.25x18x9g Spline shaft D (DIN 5480)

45˚ 4.96 Mounting flange C

20

Parker Hannifin Mobile Controls Division Trollhättan, Sweden

0.39

Hydraulic motor/pump Series F11/F12

Catalogue HY17-8249/US

Installation dimensions F11-14 (ISO versions)

3.98 1.81

4.02

Main ports M26 (metric thread; depth 0.47; ISO 9974-1)

2.09 1.77

Speed sensor (optional) Drain port M26 (metric thread; depth 0.47; ISO 9974-1)

25

1.18 4.84

5.79 (max)

Drain port M26 (metric thread; depth 0.47; ISO 9974-1)

5.47 3.54

0.47

Flange I (ISO 3019/2) 0.83

0.26 0.73 R 0.02 max

Type K key shaft 1.65 1.38 Key 8x7x35

1.10 Ø0.974

M8 (metric thread) 0.63 deep 1.10

0.14

0.31 Ø0.9846/0.9841

W25x1.235x18x9g) Type D spline shaft (DIN 5480)

Ø1.06

Ø3.1496/3.1478

Ø0.35 (x4)

0.41 (x4) Ø0.35 (x4)

B

CCW

CW

A 2.866 3.74 Type I mounting flange (ISO 3019/2)

21

Parker Hannifin Mobile Controls Division Trollhättan, Sweden

Hydraulic motor/pump Series F11/F12

Catalogue HY17-8249/US

Installation dimensions F11-14 (SAE versions)

Main ports 11/16"-12 UN, O-ring boss; SAE J514d

3.98 1.81

4.02

2.09 1.77

Drain port 9/16" UNF; O-ring boss; SAE J514d

25˚

1.18

Speed sensor (optional)

6.21 (max) Drain port 9/16" UNF, O-ring boss; SAE J514d

5.94

5.24

4.02 0.67 (x2)

Ø0.94 (x2)

0.37 0.31 R 0.02

1.50

Type T key shaft

5/16"-24 UNF-2B

1.11

(0.31) 1.30

Key 8x7x35

1.25

0.250

(0.63 deep)

Ø1.000/0.998 Ø1.06

Ø3.15 Ø4.000/3.998

0.95 Type S spline shaft 13 T, 16/32 DP (SAE J498b; class 1, 30 involute spline, flat root, side fit)

R 10.24 (x2)

B

CCW

CW

R 0.55 (x4) 29˚ (x4)

4.72 Ø0.57 (x2)

A 5.75 6.85 (max) Type S mounting flange SAE 'B' ( SAE J744c)

22

Parker Hannifin Mobile Controls Division Trollhättan, Sweden

Hydraulic motor/pump Series F11/F12

Catalogue HY17-8249/US

Installation dimensions F11-19 (SAE version)

3.46

4.49 max 2.13

Main port A 11/16"-12*

2.48 0.43

Main port B 11/16"-12*

Approx. center of gravity

1.14

Drain port D 9/16"-18

Drain port C 9/16"-18

7.13 max

6.10

4.61 2.91

0.67 0.31

1.50 Flange S

0.38

Key 1/4"x1/4"x11/4"

5/16"/24**

0.63 min

R 0.03 R 0.04 Key shaft T SAE 'B-B' (SAE J744c) Ø1.000 0.998 Ø1.11 min

1.11 Ø4.000 3.998 0.31 1.02

R 0.55

Ø0.57 (x2) 1.30

Ø6.93 max

SAE 'B' (13T, 16/32 DP; class 1, flat root, side fit) Spline shaft S (SAE J498b) 5.75 * O/ring boss (SAE J514d) ** UNC thread 30˚ 4.84 Mounting flange S SAE 'B' (SAE J744c)

23

Parker Hannifin Mobile Controls Division Trollhättan, Sweden

Hydraulic motor/pump Series F11/F12

Catalogue HY17-8249/US

Installation dimensions F12-30, -40, -60, -80 and -110 (ISO versions) A3 B3

A2

Flushing valve (optional)

C3 Port A

B2 C2

Port B

Port D

K3

G2

Port C1)

N2

G3

NOTE: Type Z has no thread

L3 H3

K2

H2 (±0.02)

R2 J2 J3

Q2

Ø E3

Type D (Z) spline shaft

F3

P2 Type K (P) key shaft

L2

Type I flange

S2 See table

D3 (thread)

Speed sensor (optional)

1) Inspection/ drain port

D2

M2 Ø E2 Ø F2

C1 A1 T3

A1 B1

Port E (third drain port) F12-110 barrel housing (ISO/cartridge version)

Type I mounting flange (ISO 3019/2)

Shown: F12-80

24

Parker Hannifin Mobile Controls Division Trollhättan, Sweden

Ø D1 (x4)

Hydraulic motor/pump Series F11/F12

Catalogue HY17-8249/US

Installation dimensions Dim.

F12-30

F12-40 F12-60

F12-80

F12-110

A1 B1 C1 D1

3.48 4.65 4.65 0.43

4.46 5.75 5.59 0.53

4.46 5.75 5.67 0.53

5.01 6.22 6.10 0.53

5.57 7.09 7.09 0.71

A2 B2 C2

3.94 2.32 0.98

4.33 2.56 1.02

4.92 2.76 0.87

5.32 3.05 1.26

5.71 3.35 1.50

D2 E2 F2

0.32 0.32 0.39 0.47 1.30 1.65 1.65 2.05 3.9370/ 4.9213/ 4.9213/ 5.5118/ 3.9349 4.9188 4.9188 5.5093 6.77 1.00 1.97 1.97

6.81 1.28 2.36 -

7.48 1.28 2.36 -

8.50 1.28 2.76 -

9.09 1.59 3.23 -

K2 L2 M2

2.16 1.58 0.20

2.05 1.97 0.20

2.13 1.97 0.20

2.76 2.21 0.28

2.61 2.76 0.24

N2 P2 Q2

5.37 0.32 1.10

5.39 0.32 1.10

6.06 0.32 1.30

6.79 0.32 1.42

7.05 0.32 1.61

R23) R24) S2*3)

1.38 1.69 M12 x24

1.38 1.38 M12 x24

1.61 M12 x28

1.77 1.61 M16 x36

1.97 M16 x36

4.80 2.60 0.937

5.28 2.60 0.937

5.67 2.60 0.937

6.10 2.95 1.094

D3* E3 F3

M12 M12 M12 M16 1.1817/ 1.1817/ 1.3787/ 1.5755/ 1.1812 1.1812 1.3780 1.5749 1.30 1.30 1.50 1.69

A, B size

0.55 2.26 6.2992/ 6.2967

G2 H2 J21) J22)

A3 B3 C3

Ports F12-30 F12-40 F12-60 F12-80 F12-110 3/

4"

3/ " 4

3/ " 4

1"

11/4"

Screw thread 1)

M10 (0.79)

M10 (0.79)

M10 (0.79)

M12 (0.79)

M14 (1.02)

C, D thread 2)

M22 x1.5

M22 x1.5

M22 x1.5

M22 x1.5

M22 x1.5

E thread 2)

-

-

-

-

M22 x1.5

A, B: ISO 6162

1) Metric thread (depth in inches) 2) Metric thread x pitch in mm.

Spline shaft (DIN 5480; in mm) Type D (standard)

Type Z (optional)

F12-30

W30x2x14x9g

W25x1.25x18x9g

-40

W32x2x14x9g

W30x2x14x9g

-60

W35x2x16x9g

W32x2x14x9g

-80

W40x2x18x9g

W35x2x16x9g

-110

W45x2x21x9g

-

Metric key shaft (in mm) Type K (standard)

Type P (optional)

F12-30

30 dia.

25 dia.

6.69 3.29 1.250

-40

30 dia.

-

-60

35 dia.

-

-80

40 dia.

-

M16 1.7724/ 1.7717 1.91

-110

45 dia.

-

G3 H3 J3

5.37 0.93 0.95

5.39 1.20 0.95

6.06 1.20 1.10

6.79 1.20 1.42

7.05 1.52 1.42

K3 L3 S3 T3

2.000 0.71 0.63 -

2.000 0.79 0.63 -

2.000 0.79 0.63 -

2.250 0.79 1.02 -

2.626 0.87 2.68

= Max 5 100 psi (350 bar) operating pressure.

* Metric thread 1) Key shaft type K 2) " " " P

3) Spline shaft type D 4) " " " Z.

25

Parker Hannifin Mobile Controls Division Trollhättan, Sweden

Hydraulic motor/pump Series F11/F12

Catalogue HY17-8249/US

Installation dimensions F12-30, -40, -60, -80 and -110 (Cartridge versions) A6

Flushing valve (optional)

B6 C6 Port A

A5

B5 C5

Port B

Port D

K6

Speed sensor (optional)

G5 G6

N5

Port C1) Q6 L6

R6

K5 H5 (±0.2)

O-ring (included)

H6

T5

P5

S5

J5

Ø M6

Type C spline shaft

L5 R5

D5

Q5

M5

Ø N6

Ø E5

Ø P6

Type K (X) key shaft

See table Ø V5

1) Inspection/ drain port

Ø F5

T6 C4

A4 Port E (third drain port) E4

F12-110 barrel housing (ISO/cartridge version)

Shown: F12-80

40 (-30, -40, -60, -110) 43 (-80)

XX˚ Ø D4 (x2)

B4

Type C mounting flange

26

Parker Hannifin Mobile Controls Division Trollhättan, Sweden

Hydraulic motor/pump Series F11/F12

Catalogue HY17-8249/US

Installation dimensions Dim.

Ports F12-30 F12-40 F12-60 F12-80 F12-110

F12-30 F12-40 F12-60 F12-80 F12-110

A4 B4 C4 D4 E4

6.30 5.51 7.40 0.55 3.03

7.87 6.46 9.25 0.71 3.74

7.87 6.46 9.25 0.71 3.74

8.82 7.72 10.24 0.87 4.33

9.84 8.11 11.26 0.87 4.57

A5 B5 C5

3.94 2.32 0.98

4.33 2.56 1.02

4.92 2.76 0.87

5.31 3.05 1.26

5.71 3.35 1.50

A, B size

1) 2)

0.39 0.47 0.55 D5 0.31 E5 1.1817/ 1) 2) 1.3787/ 1.5755/ 1.7724/ 1.1812 1.3780 1.5749 1.7717 F5 5.3150/ 6.2992/ 6.2992/ 7.4803/ 7.8740/ 5.3125 6.2967 6.2967 7.4775 7.8712 G5 H5 J5

5.00 3.50 1.97

5.24 3.63 2.36

5.75 3.63 2.36

6.18 4.35 2.76

6.89 4.83 -

K5 L5 M5

0.55 1.57 0.20

0.63 1.97 0.20

0.59 1.97 0.20

0.59 2.20 0.28

0.59 -

N5 P5 Q5

3.58 0.87 1.10

3.82 1.18 1.10

4.33 1.22 1.10

4.49 1.57 1.46

4.84 1.57 1.46

R5 S5 T5 V5

1.38 2.78 0.59 1.30

1.38 2.83 0.59 1.38

1.38 2.99 0.59 1.38

1.77 3.58 0.59 1.77

1.77 3.77 0.59 1.77

A6 B6 C6

4.80 2.60 0.937

5.28 2.60 0.937

5.67 2.60 0.937

6.10 2.95 1.094

6.69 3.27 1.250

G6 H6 K6

3.60 2.74 2.000

3.82 2.80 2.000

4.33 2.91 2.000

4.49 3.52 2.250

4.84 3.69 2.626

L6 M6 N6

0.63 3.62 4.33

0.71 4.53 5.00

0.71 4.53 5.31

0.79 5.12 6.06

0.79 5.51 6.30

P6 Q6 R6 T6

5.047 0.20 0.20 -

6.031 0.20 0.20 -

6.031 0.20 0.20 -

7.213 0.20 0.20 -

7.606 0.20 0.20 2.68

3/

3/

4"

3/

4"

4"

1"

11/4"

Screw thread 3)

M10 (0.79)

M10 (0.79)

M10 (0.79)

M12 (0.87)

M14 (1.02)

C thread 4)

M14 x1.5

M14 x1.5

M14 x1.5

M14 x1.5

M14 x1.5

D, E thread 4)

M18 x1.5

M18 x1.5

M22 x1.5

M22 x1.5

M22 x1.5

A, B: ISO 6162

3) Metric thread (depth in inches) 4) Metric thread x pitch in mm.

Spline shaft (DIN 5480; in mm) Type C (standard) F12-30

W30x2x14x9g

-40 -60 -80 -110

W30x2x14x9g W30x2x14x9g W40x2x18x9g W40x2x18x9g

Metric key shaft (in mm) Type K (std) Type X (opt.)

F12-30

30 dia.

–

-40 -60 -80 -110

35 dia.

40 dia.

–

35 dia.

– – –

O-ring dimensions (in mm) F12-30 -40 -60 -80 -110

127x4 150x4 150x4 180x4 190x4

1) Key shaft type K: D5 - 0.31; E5 - 1.1817/1.1812 2) Key shaft type X: D5 - 0.39; E5 - 1.3787/1.3780

27

Parker Hannifin Mobile Controls Division Trollhättan, Sweden

Hydraulic motor/pump Series F11/F12

Catalogue HY17-8249/US

Installation dimensions F12-30, -40, -60, -80 and -110 (SAE versions with 4 bolt flange)

A9 C9 Port A

A8

Flushing valve (optional)

B9

B8 C8

Port B Port D K9

Port C1)

G8 G9

N8 K8

Speed sensor (optional)

L9

H9

H8

R8

J9

Type S flange D9 (thread)

Q8 Ø E9

See table

Type S (U) spline shaft

F9

Type T key shaft J8

L8

D8

1) Inspection/ drain port

M8

Ø E8 Ø F8

C7

T9 A7

Port E (third drain port)

F12-110 barrel housing (SAE version)

A7

Shown: F12-80 with 4 bolt flange

Type S (SAE 4 bolt) mounting flange

Ø D7 (x4)

B7

28

Parker Hannifin Mobile Controls Division Trollhättan, Sweden

Hydraulic motor/pump Series F11/F12

Catalogue HY17-8249/US

Installation dimensions Dim.

F12-30

F12-40

F12-60

A7 B7 C7 D7

3.54 4.65 4.65 0.55

4.51 5.83 5.67 0.55

4.51 5.83 5.67 0.55

4.51 6.10 6.10 0.55

6.36 8.03 7.87 0.83

A8 B8 C8

3.94 2.32 0.98

4.33 2.56 1.02

4.92 2.76 0.87

5.31 3.05 1.26

5.71 3.35 1.50

D8 E8 F8

0.25 1.30 4.000/ 3.998

0.31 1.65 5.000/ 4.998

0.31 1.65 5.000/ 4.998

0.38 2.05 5.000/ 4.998

0.44 2.26 6.000/ 5.998

G8 H8 J8

7.46 0.31 1.50

7.76 0.31 1.89

8.43 0.31 1.89

9.45 0.31 2.13

10.39 0.31 2.64

K8 L8 M8

2.83 1.25 0.10

2.99 1.50 0.16

3.11 1.50 0.16

3.74 1.75 0.16

3.90 2.13 0.29

N8 Q81) Q82)

6.04 0.91 -

6.34 0.91 -

7.02 0.91 -

7.76 0.98 0.91

8.35 1.34 -

R81) R82)

1.30 -

1.89 -

1.89 -

2.13 1.88

2.63 -

A9 B9 C9

4.80 2.60 0.937

5.28 2.60 0.937

5.67 2.60 0.937

6.10 2.95 1.094

6.69 3.27 1.250

D9* E9

5/

16"-24

3/

8"-24

3/

8"-24

F12-80 F12-110

1/

2"-20

5/

Ports F12-30 F12-40 F12-60 F12-80 F12-110 A, B size

8"-14

7/

8"-14

7/

8"-14

7/

8"-14

11/16"-12

D thread

3/

4"-16

3/

4"-16

7/

8"-14

7/

8"-14

11/16"-12

E thread

1.500/ 1.498 1.67

1.750/ 1.748 1.94

G9 H9 J9

6.06 0.38 0.63

6.34 0.50 0.75

7.02 0.50 0.75

7.76 0.50 1.02

8.35 0.50 1.26

K9 L9 T9

2.000 0.71 -

2.000 0.79 -

2.000 0.79 -

2.250 0.79 -

2.626 0.87 2.68

8"-16

(0.79)

-

8"-16

7/

(0.87)

-

16"-14

(1.06)

-

1/

2"-13 (0.98)

11/16"-12

-

A, B: ISO 6162; C, D, E: O-ring boss (SAE J514) 3) UN thread (depth in inches)

Mounting flange (SAE J744)

F12-30 -40 -60 -80 -110

S (standard)

X (optional)

SAE 'B', 4 bolt SAE 'C', " SAE 'C', "

-

SAE 'C', SAE 'D',

" "

SAE ’D’, 4 bolt -

Spline shaft (SAE J498b, class 1, flat root, side fit) S (standard) U (opt.)

X (optional) F12-30

-60

F9

1.250/ 1.248 1.39

11/4"

1"

7/

(0.87)

3/

4"

C thread

8"-16

3/

3/

4"

3/

-40

1.250/ 1.248 1.39

3/

4"

Screw thread 3)

8"-18

1.000/ 0.998 1.11

3/

-80 -110

SAE 'B' 13T, 16/32 DP SAE 'C' 14T, 12/24 DP SAE 'C' 14T, 12/24 DP SAE 'C-C' 17T, 12/24 DP SAE 'D' 13T, 8/16 DP

-

-

-

-

-

-

SAE 'C' SAE 'D' 14T,12/24DP 13T, 8/16 DP -

= Max 5 100 psi (350 bar) operating pressure.

Key shaft (SAE J744) T (standard)

* UNF-2B thread 1) Spline shaft type S 2) " " " U

F12-30 -40

Main ports A and B, type U (optional) F12-110 1 5/8" - 12 UN

-60

O-ring ports according to SAE J514d -80 -110

29

SAE 'B-B' (1"/ 25.4 mm) SAE 'C' (11/4"/ 31.75 mm) SAE 'C' (11/4"/ 31.75 mm) SAE 'C-C' (11/2"/ 38.1 mm) SAE 'D' (13/4"/ 44.45 mm)

X (optional) SAE ’D’ (13/4"/ 44.45 mm ) -

Parker Hannifin Mobile Controls Division Trollhättan, Sweden

Hydraulic motor/pump Series F11/F12

Catalogue HY17-8249/US

Installation dimensions F12-30, -40, and -60 (SAE versions with 2 bolt flange)

A12 Flushing valve (optional)

B12 C12 Port A

A11

B11 C11

Port B

Port D

K12 G11 Port C (inspection/ drain port)

G12

K11

N11

Speed sensor (optional)

L12 H11

R11

H12 Type T flange

J12 D12 (thread) Ø E12 F12

Q11

J11

See table

Type T key shaft

L11 D11 Ø E11

Type S spline shaft

M11

Ø F11

Shown: F12-60 with 2 bolt flange

C10 R E10 R F10 Ø D10 (x2)

A10 B10

30

Parker Hannifin Mobile Controls Division Trollhättan, Sweden

Hydraulic motor/pump Series F11/F12

Catalogue HY17-8249/US

Installation dimensions Dim.

F12-30

F12-40

F12-60

A10 B10 C10

5.75 6.93 2.48

7.13 8.46 2.91

7.13 8.46 2.91

A, B size Screw thread 1)

3/

D10 E10 F10

0.57 0.39 0.39

0.69 0.63 0.61

0.69 0.63 0.61

C thread

3/

D thread

3/

A11 B11 C11

3.94 2.32 0.98

4.33 2.56 1.02

4.92 2.76 0.87

D11 E11 F11

0.25 1.30 4.000/ 3.998

0.31 1.65 5.000/ 4.998

0.31 1.65 5.000/ 4.998

G11 H11 J11

7.46 0.31 1.50

7.76 0.31 1.89

8.43 0.31 1.89

K11 L11 M11

2.80 1.25 0.10

3.03 1.50 0.16

3.21 1.50 0.16

N11 Q11 R11

6.06 1.02 1.30

6.34 1.06 1.89

7.03 1.06 1.89

A12 B12 C12

4.80 2.60 0.937

5.28 2.60 0.937

5.67 2.60 0.937

D12 * E12

5/

16"-24

3/

8"-24

3/

Ports

F12

1.250/ 1.248 1.39

1.250/ 1.248 1.39

G12 H12 J12

6.06 0.38 0.63

6.34 0.50 0.75

7.03 0.50 0.75

K12 L12

2.000 0.71

2.000 0.79

2.000 0.79

3/

F12-40 3/

4"

4"

3/

8"-16 (0.87)

8"-16 (0.79)

4"-16

3/

4"-16

3/

F12-60 3/

4"

3/

8"-16 (0.87)

4"-16

7/

8"-14

4"-16

7/

8"-14

A, B (main ports): SAE J518c (6000 psi) C, D (drain ports): O-ring boss (SAE J514) 1) UN thread (depth in inches).

Main ports A and B, type U (optional) F12-30 1 1/16" - 12 UN -40 1 5/16" - 12 UN -60 1 5/16" - 12 UN O-ring ports according to SAE J514d = Max 350 bar operating pressure.

Mounting flange (SAE J744) Type T

8"-24

1.000/ 0.998 1.11

F12-30

F12-30

SAE 'B', 2 bolt

-40

SAE 'C', 2 bolt

-60

SAE 'C', 2 bolt

Spline shaft(SAE J498b, class 1, flat root, side fit) Type S F12-30

SAE 'B' 13 T; 16/32 DP

-40

SAE 'C' 14 T; 12/24 DP

-60

SAE 'C' 14 T; 12/24 DP

* UNF-2B thread Key shaft (SAE J744) Type T F12-30

31

1" dia.

SAE 'B-B'

-40

11/4" dia. SAE 'C'

-60

11/4" dia. SAE 'C'

Parker Hannifin Mobile Controls Division Trollhättan, Sweden

Hydraulic motor/pump Series F11/F12

Catalogue HY17-8249/US

Installation dimensions F11-150 (CETOP version) 8.74 max 3.98

6.77

ØM16(x8)*

1.44

4.65 0.71

Main port A 1 1/2" **

Main port B 1 1/2" **

Approx. center of gravity Drain port D BSP 3/4"

3.125 3.35

Drain port C BSP 3/4" 12.09

9.84

6.26 0.98

4.29

1.81 1.97 10

R 0.04 R 0.03

3.23

Type K key shaft

Flange C

1.18 Ø1.9692/ 1.9686

M16 (metric thread)

Ø2.24 min Ø7.8740 7.8712

2.11

14x9x70 (0.55x0.35x2.76; metric key)

Ø9.84 1.97

1.18 1.97

M16 (metric thread)

Ø0.87(x4)

9.29

W45x2x21x9g (metric spline) Spline shaft D (DIN 5480)

9.29 max

* Metric thread, deep1.4 ** 6000 psi flange (SAE J581c)

Type C mounting flange

32

Parker Hannifin Mobile Controls Division Trollhättan, Sweden

Hydraulic motor/pump Series F11/F12

Catalogue HY17-8249/US

Installation dimensions F11-150 (SAE version)

8.74 max 3.98

6.77

ØM16* (x8)

1.437

4.65 0.71

Main port A 1 1/2" **

Main port B 1 1/2" **

Approx. center of gravity Drain port D BSP 3/4"

3.13 Drain port C BSP 3/4"

3.35 11.69

13.98 8.11 0.94

6.18 0.31

0.50

2.63

R 0.03

R 0.04 Flange S

1.18

1.94

Key shaft T SAE 'D' (SAE J744c)

Ø1.750/ 1.748

Ø2.24 min Ø6.000/ 5.998

7/ "x7/ "x21/ " 16 16 8 (key)

0.31 Ø0.83 (x4)

7.56

6.362

2.63

SAE 'D'; 13T, 8/16 DP; class 1, flat root, side fit Spline shaft S (SAE J498b)

8.43 max

* Metric thread, deep1.4 ** 6000 psi flange (SAE J581c)

Mounting flange S SAE 'D' (SAE J744c)

33

Parker Hannifin Mobile Controls Division Trollhättan, Sweden

Hydraulic motor/pump Series F11/F12

Catalogue HY17-8249/US

Installation dimensions F11-250 (SAE version)

9.13 3.98 1.437 Main port A 1 1/2" *

M16 (x8) 1.4 deep (metric thread)

7.76 1.06

Main port B 1 1/2" *

Approx. center of gravity

3.125 Ø1.54 (x2)

5.55

4.65

Drain port D BSP 3/4"

15.55

Drain port C BSP 3/4"

13.23

8.50 0.94

7.09 0.31

R 0.03

3.23

0.50 1.22 M16 (metric thread)

R 0.03

Type K key shaft (metric; not SAE)

2.11 Ø6.000/ 5.998

14x9x70 (0.55x0.35x2.76; metric key) Ø1.9692/ 1.9686 Ø2.24 min

0.31

8.11 max 6.36

1.38

SAE F; 15T, 8/16 DP; class 1, flat root, side fit Optional: SAE S; 13T, 8/16 DP

2.63 Spline shaft F (SAE J498b) 6.36 8.11 max

Ø0.83 (x4) * 6000 psi flange (SAE J581c)

Mounting flange S SAE 'D' (SAE J744c)

34

Parker Hannifin Mobile Controls Division Trollhättan, Sweden

Hydraulic motor/pump Series F11/F12

Catalogue HY17-8249/US

Technical information F11 saw motors Series F11 motors have proven extremely reliable in demanding applications such as bar (chain) saws.

Primarily due to the 40° bent-axis design, spherical pistons (with laminated piston rings) and gear synchronization, very high speeds are permissible. Not even low temperatures at start-up affect reliability.

To further enhance the saw function and, at the same time, reduce weight, cost and installation dimensions, a specific saw motor has been developed (frame sizes -10, -14 and -19; refer to the illustration to the right) which is specifically dedicated to bar saws. The motor allows the saw bar bearings to be mounted directly on the motor housing, and the spur gear installs on the motor shaft without any additional bearings.

For more detailed information (available versions, ordering codes, installation dimensions, etc.), refer to 'F11 Saw Motors' (catalogue 9129 8245-02).

F11 with built-in make-up valve

Saw bar supported directly on the motor flange Feed cylinder

Chain spur gear mounted Saw directly on the shaft chain

Protective cover

Saw bar

Chain saw installation (example; F11-10 shown)

F11 fan motors

Port A

Main port B

Port G

Main port A Built-in make-up valve

Drain port C

Mounting flange C (CETOP)

Key shaft K (CETOP)

A

Frame sizes -10, -14 and -19 are also available as 'fan motors' with a built-in check valve (refer to the schematic below) and CETOP mounting flange. Just like the saw motor, the fan motor can be operated at very high speeds without reliability problems.The fan is usually installed directly on the motor shaft without additional bearing support.

Additional information (available versions, ordering codes, installation dimensions, etc.) is available in publication 'F11 Fan Motors' (catalogue 9129 8247-02).

Port B

Port G Only for F11-10, -19 (for make-up flow if required)

Alternative drain port D

Fan motor (F11-10 shown).

Port C/D

Fan motor schematic (left hand rotation shown).

35

Parker Hannifin Mobile Controls Division Trollhättan, Sweden

Catalogue HY17-8249/US

Technical information

Hydraulic motor/pump Series F11/F12

F12 integrated flushing valve (F12-30, -40, -60 and -80) Series F12 (except F12-110; refer to the FV13 flushing valve block below) is available with an integrated flushing valve which provides the rotating parts with an additional cooling flow, required when operating at high speeds and power levels.

In a hydrostatic transmission, the valve also ensures that part of the main circuit fluid is being removed and replaced by cool, filtered fluid from the charge pump.

The flow is limited by a suitably sized nozzle that installes below a plug in the motor port flange.

Built-in flushing valve Nozzle (optional)

NOTE: Ordering code, available nozzles and other information is provided in publication ’Mobile motor/pump accessories’ (catalogue HY17-8258/UK).

Integrated flushing valve (F12-30, -40, -60, -80)

Nozzle (optional)

Port A

Port B

F12 accessory valve blocks Type FV13 flushing valve (for F12-110) A separate flushing valve block is available for the F12-110. It has the same function as the integrated valve for the other F12 frame sizes (above).

The valve block mounts between the motor port flange and the split flanges as shown to the right.

An optional nozzle can be installed in the valve block drain port.

Ordering code: FV13

Nozzle (optional) FV13 flushing valve block

NOTE: Additional information is available in publication ’Mobile motor/pump accessories’ (catalogue HY17-8258/UK).

Nozzle (optional) Port A

Port B FV13 flushing valve block

36

Parker Hannifin Mobile Controls Division Trollhättan, Sweden

Catalogue HY17-8249/US

Technical information

Hydraulic motor/pump Series F11/F12

Type BT brake valve When a motor (in an open loop system) is used in a hydrostatic vehicle transmission, the motor may operate faster than what corresponds to the available pump flow (e.g. in a steep downhill); this can lead to motor cavitation and loss of braking power.

The BT brake valve prevents cavitation by throttling the return flow from the motor as soon as the pressure level in the inlet port decreases to approximately 35 bar. At the same time, motor braking is provided when the pump flow decreases or is shut off.

The BT brake valve can be supplied with various optional functions such as a mechanical brake release valve and a flushing valve.

The valve block is very compact and installs between the motor port flange and the split flanges (refer to the illustration).

BT brake valve block

Brake release valve flushing valve etc.

BT brake valve block

F12motor

Port BR (brake release)

The BT valve block is available in two sizes: - BT21 (3/4") for F12-30, -40, -60 - BT22 (1") for F12-80

Port A

NOTE: Detailed information on the BT valve is provided in publication ’Mobile motor/pump accessories’ (catalogue HY17-8258/UK).

Port B Port S (make-up)

Type SR pressure relief/make-up valve The SR pressure relief/make-up valve block for series F12 motors is designed to protect the motor from high pressure spikes as well as provide an excellent makeup function to help prevent motor cavitation (when port G is pressurized).

The valve block mounts between the motor port flange and the split flanges (as shown to the right).

Port G

The SR block is available in three sizes: - SR11 (3/4") for F12-30, -40, -60 - SR12 (1") for F12-80 - SR13 (11/4") for F12-110

SR valve block

NOTE: - For additional information such as pressure settings and installation dimensions, refer to publication ’Mobile motor/pump accessories’ (catalogue HY17-8258/UK).

Port G Port L SR valve block F12-motor Port A

- To obtain a combined cross-over relief/ make-up and flushing function on the F12-110, the SR13 and FV13 valve blocks can be stacked (with the flushing valve block mounted next to the motor).

Port B

37

Parker Hannifin Mobile Controls Division Trollhättan, Sweden

Catalogue HY17-8249/US

Technical information

Hydraulic motor/pump Series F11/F12

Type SV pressure relief valve The SV pressure relief valve for series F12 motors protects the motor and the corresponding main hydraulic lines from pressure spikes. Like the SR valve block (page 31), it has integrated cartridge type pressure relief valves and mounts between the motor port flange and the split flanges as shown to the right.

The design of the relief valves permits a limited makeup flow (when port L is pressurized).

The SV valve block is available in three sizes: - SV11 (3/4") for F12-30, -40, -60 - SV12 (1") for F12-80 1 - SV13 (1 /4") for F12-110

SV pressure relief valve block

(Port L)

NOTE: - Detailed information on available pressure settings, installation dimensions, etc. is provided in publication ’Mobile motor/pump accessories’ (catalogue HY17-8258/UK).

Port A

- On the F12-110, the FV13 flushing valve block (page 36) can be mounted between the SV13 block and the motor port flange to obtain a combined pressure relief and flushing function.

Port B SV valve block

Speed sensor Speed sensor

A speed sensor kit is available for series F11/F12.

A ferrostat differential (Hall-effect) sensor installs in a separate, threaded hole in the F11/F12 bearing housing.

On F12 the speed sensor is directed towards the ring gear.On F11 the speed sensor is directed towards the pistons. The speed sensor outputs a square wave signal within a fequency range of 5 Hz to 20 kHz. NOTE: - The motor bearing housing must be prepared for the speed pick-up; refer to the F11/F12 ordering codes (pages 7-12).

F12 with speed sensor.

- On F11 the pistons position must be known before mounting.

- Additional information is provided in ’Mobile motor/pump accessories’ (catalogue HY17-8258/UK).

Speed sensor

- The speed sensor is also shown in the illustrations on pages 19, 21, 22, 24, 26 and 28.

F11-14 with speed sensor.

38

Parker Hannifin Mobile Controls Division Trollhättan, Sweden

Hydraulic motor/pump Series F11/F12

Catalogue HY17-8249/US

Technical information F12 main port suction fittings Suction fittings To minimize the risk for cavitation when operating the F12 as a pump, we recommend using our suction fittings; all take 2" hoses.

Part no.

SAE size

For

L [inch]

379 4070

3/ " 4

F12-30 F12-40 F12-60

3.94

370 4095 370 3916

1" 11/4"

F12-80 F12-110

3.94 4.02

Suction fitting

(Split-flange half)

(Mounting screw)

(O-ring) 2" hose

L

The suction fittings are designed for use with standard SAE or metric split-flange halves as shown.

O-ring and mounting screw sizes are listed below.

SAE size

O-ring dimension [mm]

3/ " 4

30.0x3.53 32.9x3.53 37.7x3.53

1" 1 1 /4"

Screw size SAE Metric 3/ "-16x1.50 8 7/ "-14x1.50 16 1/ "-13x1.75 2

M10x35 M12x40 M14x45

Suction fitting kits Suction fitting kits are available for the F12 ISO and Cartridge versions. A kit consists of a suction fitting (shown above), two split-flange halves, an O-ring and four mounting screws.

Part no.

379 4421 370 4098 370 3926

SAE size

For

Screw size

3/ " 4

F12-30/-40/-60 F12-80 F12-110

M10x35 M12x40 M14x45

1" 1 1 /4"

Split-flange kits Separate metric split-flange kits, consisting of two splitflange halves and four mounting screws for use on the F12 ISO and cartridge versions, are also available.

Part no.

379 4405 370 4329 370 4330

SAE size

For

Screw size

3/ " 4

F12-30/-40/-60 F12-80 F12-110

M10x35 M12x40 M14x45

1" 11/4"

(Split-flange half)

39

(Mounting screw)

Parker Hannifin Mobile Controls Division Trollhättan, Sweden

Hydraulic motor/pump Series F11/F12

Catalogue HY17-8249/US

Installation information Direction of rotation The M and H versions of series F11, and the M version of series F12, are bi-directional.

The L and R pump versions are uni-directional, allowing higher selfpriming speeds (refer to page 14).

The illustration to the right shows direction of flow versus shaft rotation. In a motor application, the shaft turns clockwise when port B (black arrow) is pressurized, and counter clockwise when port A (open arrow) is pressurized.

In a pump application where the shaft turns clock-wise, port B is the inlet port and should be connected to tank; when the shaft turns counter clockwise, port A is the inlet port.

Port A

Port B

Counter clockwise rotation

Clockwise rotation

NOTE: When operating the F11/F12 as a pump above the selfpriming speed (valid for both the pump and motor versions), the inlet must be sufficiently pressurized. Increased noise and deteriorating performance may otherwise be experienced.

For further information refer to ’Selfpriming speed and required inlet pressure’ on page 6.

Hydraulic fluids Ratings and performance data for series F11/F12 are based on operating with good quality, contaminationfree, petroleum-based fluids.

Hydraulic fluids type HLP (DIN 51524), automatic transmission fluids type A, or API CD engine oils can be used.

Fire resistant fluids (when used under modified operating conditions) and synthetic fluids may also be suitable.

For additional information, refer to Hydraulic Marketing IS data base: - Hydraulic fluid specifications - Fire resistant fluids.

Operating temperature The following temperatures should not be exceeded (type H and N shaft seals): Drain fluid: 195 °F (90 °C) Viton shaft seals (F11 type E, F12 type V) can be used to 240 °F (115 °C) drain fluid temperature.

NOTE: The temperature should be measured at the utilized drain port.

Continuous operation may require case flushing in order to meet the viscosity and temperature limitations.

The following table shows operating speeds, above which flushing is usually required, as well as suggested flow through the case.

Series F11 Frame size F11-5 F11-10 F11-14 F11-19 F11-150 F11-250

Speed [rpm] Flow [l/min] Flow [gpm] 5500 1–2 0.25-0.5 4500 2–3 0.5-0.8 4500 2–3 0.5-0.8 4000 2–4 0.5-1.0 2200 10–20 2.6-5.2 1800 12–22 3.2-5.8

Series F12 Frame size F12-30 F12-40 F12-60 F12-80 F12-110

40

Speed [rpm] Flow [l/min] Flow [gpm] 3500 4–8 1.0–2.1 3000 5–10 1.3–2.6 3000 7–14 1.9–3.7 2500 8–16 2.1–4.2 2300 9–18 2.4–4.8

Parker Hannifin Mobile Controls Division Trollhättan, Sweden

Hydraulic motor/pump Series F11/F12

Catalogue HY17-8249/US

Installation information Viscosity The ideal operating range is75 to 150 SUS (15 to 30 mm2/s).

At operating temperature, the viscosity (of the drain fluid) should be kept above 46 SUS (8 mm2/s [cSt]).

At start-up, the viscosity should not exceed 5 000 SUS (1000 mm2/s) Filtration To obtain the highest service life of the F11/F12, the fluid cleanliness should meet or exceed ISO code 18/13 (ISO 4406).

During normal operating conditions, a 10 µm (absolute) filter is recommended.

Case pressure The tables below show the highest recommended case pressure as a function of shaft speed.

‘Nominal’ shaft seal life can be expected at a certain speed and the corresponding max case pressure. Seal life will be shorter, however, at unfavourable operating conditions (high temperature, low oil viscosity, contaminated oil).

Series F11 Speed Shaft seal F11-5 F11-10 F11-14 F11-19 F11-150 F11-250

Max case pressure [psi] versus shaft speed [rpm] 1500 3000 4000 5000 6000 8000 9000 10000 11000 12000 H/V N/E H/V N/E H/V N/E H/V N/E H/V N/E H/V N/E H/V N/E H/V N/E H/V N/E H/V N/E 20 20 19 19

2.2 13 1.9 2.2 11.5 1.8 2.2 9.5 1.5 2.2 9.5 1.4

9.5 2.2 9.5 -

4.5 0.6 4.5 -

10 8.5 7 7

1.6 1.2 1.0 0.9

8 7 5.5 5.5

1.3 1.0 0.8 0.6

6.5 5.5 4.5 4.5

0.9 0.7 0.5 0.4

5 4 3.5 3.5

0.6 0.5 0.4 0.3

-

-

-

-

-

-

-

-

4.2 0.5 3.8 0.4 3.0 0.2 3.0 0

-

-

4 0.3 3.5 0.2 2.5 0 -

-

-

3.5 0.2 3.0 0 -

-

-

Max recommended case pressure versus shaft speed - F11 seal types H or V and N or E. Series F12 Speed Shaft seal

Max case pressure [psi] vs. shaft speed [rpm] 1500 3000 4000 5000 6000 H/V N H/V N H/V N H/V N H/V N

F12-30 F12-40 F12-60

205 30 175 30 175 30

100 20 85 15 85 15

80 15 65 10 65 10

F12-80 F12-110

145 30 140 30

70 10 65 10

60 -

5 -

65 10 50 5 50 5 -

50 -

-

-

-

-

Max recommended case pressure versus shaft speed F12 seal types H or V, and N

41

Parker Hannifin Mobile Controls Division Trollhättan, Sweden

3 -

0 -

-

-

Hydraulic motor/pump Series F11/F12

Catalogue HY17-8249/US

Installation information Case drain connections Series F11/F12 have two drain ports, C and D, while F12-110 has an additional port, E. The uppermost drain port (such as port C in the illustration below) should always be utilized.

Drain flow Port C

Port E (F12-110)

Port D Flushing flow (when required)

In mounting positions such as 'shaft up' (below) a spring loaded check valve should be installed in the drain line in order to insure a sufficiently high oil level in the case.

Preferably, the drain line should be connected directly to the reservoir.

Spring loaded check valve Drain flow

Before start-up Make sure the F11/F12 case as well as the entire hydraulic system is filled with a recommended fluid.

The internal leakage, especially at low operating pressures, is not sufficient to provide lubrication at start-up.

NOTE: -

-

-

To avoid cavitation and obtain a low noise level as well as reduced heat generation, tubes, hoses and fittings must be adequately dimensioned.

Preferably, the suction line flow speed should be 1.5 to 3.5 fps (0.5 to 1 m/s), and pressure line flow speeds 10 to 16 fps (3 to 5 m/s).

For series F12, suitable suction fittings are available (refer to page 39).

42

Parker Hannifin Mobile Controls Division Trollhättan, Sweden

Catalogue HY17-8249/US

General information

Hydraulic motor/pump Series F11/F12

! WARNING FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF THE PRODUCTS AND/OR SYSTEMS DESCRIBED HEREIN OR RELATED ITEMS CAN CAUSE DEATH, PERSONAL INJURY AND PROPERTY DAMAGE. This document and other information from Parker Hannifin Corporation, its subsidiaries and authorized distributors provide product and/or system options for further investigation by users having technical expertise. It is important that you analyze all aspects of your application, including consequences of any failure, and review the information concerning the product or system in the current product catalogue. Due to the variety of operating conditions and applications for these products or systems, the user, through its own analysis and testing, is solely responsible for making the final selection of the products and systems and assuring that all performance, safety and warning requirements of the application are met.

The products described herein, including without limitation, product features, specifications, designs, availability and pricing, are subject to change by Parker Hannifin Corporation and its subsidiaries at any time without notice.

Offer of Sale Please contact your Parker representation for a detailed ”Offer of Sale”.

43

Parker Hannifin Mobile Controls Division Trollhättan, Sweden

Hydraulics Group Sales Offices North America

Latin America

USA, Canada

Pan American Division

100 Parker Drive Otsego, MI 49078 USA Tel: +1 269-694-9411 Fax: +1 269-694-4638

7400 N.W. 19th Street Suite A Miami, FL 33126 USA Tel: +305 470 8800 Fax: +305 470 8808

Mexico Via de Ferrocarril a Matamoros #730 Apodaca, N.L. Mexico C.P. 6 6 6 0 0 Tel: +52 81 56 6000 Fax: +52 81 56 6076

Argentina Stephenson 2711 (1667) Tortuguitas–Malvinas Argentinas Pcia. de Buenos Aires Argentina Tel: +54 11 4752 4129 Fax: +54 11 4752 3704

Brazil Av. Lucas Nogueira Garcez 2181 Jacarei, SP Brazil 12300-000 Brazil Tel: +55 12 354 5100 Fax: +55 12 354 5262

Chile Av. Americo Vespucio 2760-C, Conchali Santiago Chile Tel: +56 2 623 1216 Fax: +56 2 623 1421

Venezuela Av. Principal de Boleita Norte con Calle Miraima, Edf. Draza, Planta Baja Caracas 1070 Venezuela Tel: +58 212 238-5422 Fax: +58 212 239-2272

Parker Hannifin is the world’s premier supplier of motion and control systems and solutions, with sales and manufacturing facilities throughout the world.

For product information and details of your nearest Parker sales office, visit us at www.parker.com or call free on 1-800-272-7537 (North America).

Catalogue HY17-8249/US 2M 03/04 RT © Copyright 2004 Parker Hannifin Corporation All rights reserved.