New Holland E70BSR Midi Crawler Excavator ROPS Tier III Operator's Manual 84365677 - PDF DOWNLOAD

E70BSR Midi Crawler Excavators ROPS Tier III

BUILT AROUND YOU

OPERATOR’S MANUAL E70BSR Midi Crawler Excavators ROPS Tier III

Print no. 84365677 1st Edition English 09/10 ORIGINAL INSTRUCTIONS

TABLE OF CONTENTS

FOREWORD FOREWORD..................................................................................................................... 0-3 GENERAL...................................................................................................................... 0-3 PERIODIC INSPECTIONS ............................................................................................ 0-3 NOTICE ......................................................................................................................... 0-3 KEEP OPERATION & MAINTENANCE MANUAL STORAGE ......................................... 0-4 FOR ORDERING .............................................................................................................. 0-5

1. SAFETY PRECAUTIONS 1.1 GENERAL SAFETY INFORMATION ....................................................................... 1-3 1.2 SAFETY PRECAUTIONS......................................................................................... 1-4 1.3 WARNING LABELS & DECALS............................................................................... 1-6 1.3.1

WARNING LABELS & DECALS MAINTENANCE............................................. 1-6

1.3.2

LOCATION OF WARNING LABELS & DECALS............................................... 1-6

1.4 PRE-START SAFETY .............................................................................................. 1-14 1.5 SAFETY DURING OPERATION .............................................................................. 1-20 1.6 INSPECTION & MAINTENANCE SAFETY .............................................................. 1-28 1.7 BATTERY SAFETY .................................................................................................. 1-33 1.8 PROHIBITED MACHINE OPERATION.................................................................... 1-35 1.9 END OF WORK SHIFT SAFETY ............................................................................. 1-38 1.10 TOWING THE MACHINE ......................................................................................... 1-39 1.11 USE FOPS AND FRONT GUARD ........................................................................... 1-40 1.12 USE SAFETY VALVE AND OVERLOAD ALARM.................................................... 1-41 1.13 ENSURING VISIBILITY............................................................................................ 1-42

2. MACHINE FAMILIARIZATION 2.1 BASIC COMPONENTS OF THE MACHINE ............................................................ 2-3 2.2 OPERATOR CAB NOMENCLATURE...................................................................... 2-4 2.3 COMPONENT & CONTROLS NOMENCLATURE................................................... 2-5 2.3.1

GAUGE CLUSTER ............................................................................................ 2-5

2.3.2

LOCATION OF SWITCHES AND METERS...................................................... 2-18

2.3.3

LEVERS AND PEDALS..................................................................................... 2-22

2.3.4

FUSES & RELAY BOX ...................................................................................... 2-26

2.3.5

FUSIBLE LINK (FOR STARTER) ...................................................................... 2-28

2.3.6

MECHATRO-CONTROLLER (CPU), ENGINE CONTROLLER (ECU) ............. 2-29

2.3.7

HANDLING OF RADIO...................................................................................... 2-30

2.3.8

AIR CONDITIONER........................................................................................... 2-37

2.3.9

HANDLING OF SEAT BELT.............................................................................. 2-43

2.3.10 OPERATOR SEAT ............................................................................................ 2-44 1

TABLE OF CONTENTS 2.3.11 ARM REST ADJUSTMENT............................................................................... 2-45 2.3.12 ADJUSTMENT OF CONTROL LEVER ............................................................. 2-45 2.3.13 OPERATOR CAB .............................................................................................. 2-46 2.3.14 EMERGENCY ESCAPE FROM CAB................................................................ 2-49 2.3.15 FUEL PUMP ...................................................................................................... 2-50 2.3.16 ENGINE ROOM LAMP...................................................................................... 2-51 2.3.17 OTHER EQUIPMENT (ACCESSORY).............................................................. 2-52

3. MACHINE OPERATION 3.1 MACHINE OPERATION........................................................................................... 3-3 3.1.1

EVERYDAY CHECK-UP ................................................................................... 3-3

3.1.2

CHECKING BEFORE STARTING ENGINE...................................................... 3-4

3.1.3

ADJUSTING OPERATOR SEAT....................................................................... 3-10

3.1.4

ADJUSTING MIRROR....................................................................................... 3-10

3.1.5

CHECKING FUNCTION OF GAUGE CLUSTER .............................................. 3-11

3.1.6

CHECKING WORK LIGHT................................................................................ 3-11

3.1.7

STARTING ENGINE.......................................................................................... 3-12

3.1.8

STOPPING MACHINE ENGINE........................................................................ 3-16

3.1.9

INSPECTION AFTER STARTING ENGINE...................................................... 3-17

3.1.10 MACHINE WARMING-UP ................................................................................. 3-19 3.1.11 WORK MODE SELECT SWITCH ..................................................................... 3-21 3.1.12 CONTROLS DECAL.......................................................................................... 3-22 3.1.13 MACHINE OPERATION.................................................................................... 3-23 3.1.14 PRACTICES TO IMPROVE EFFICIENCY ........................................................ 3-32 3.1.15 FLAGMAN HAND SIGNALS ............................................................................. 3-35 3.1.16 PARKING THE MACHINE................................................................................. 3-41 3.1.17 PRECAUTIONS AFTER OPERATION.............................................................. 3-42 3.1.18 MACHINE OPERATION IN ADVERSE WEATHER CONDITIONS .................. 3-43

4. MAINTENANCE 4.1 GENERAL INFORMATION ...................................................................................... 4-3 4.2 GENERAL SAFETY & PRECAUTIONS .................................................................. 4-5 4.3 LUBRICANT, FUEL & COOLANT SPECIFICATIONS ............................................. 4-11 4.4 USE OF BIO-DEGRADABLE OILS.......................................................................... 4-13 4.5 MAINTENANCE PARTS .......................................................................................... 4-14 4.6 TORQUE VALUES FOR SPECIFIED ...................................................................... 4-15 4.7 TORQUE SPECIFICATIONS FOR BOLTS & NUTS .............................................. 4-17 4.8 TORQUE SPECIFICATIONS FOR JOINTS & HYDRAULIC HOSES...................... 4-20 4.9 INSPECTION & MAINTENANCE CHART ............................................................... 4-22 2

TABLE OF CONTENTS 4.10 WHEN REQUIRED................................................................................................... 4-26 4.11 PRE-START (EVERY 8 HOURS) INSPECTION & MAINTENANCE ....................... 4-34 4.12 50 HOUR (WEEKLY) INSPECTION & MAINTENANCE PROCEDURES................ 4-35 4.13 100 HOUR INSPECTION & MAINTENANCE PROCEDURE .................................. 4-39 4.14 120 HOUR INSPECTION & MAINTENANCE PROCEDURE .................................. 4-40 4.15 250 HOUR (3-MONTH) INSPECTION & MAINTENANCE PROCEDURE............... 4-42 4.16 500 HOUR INSPECTION & MAINTENANCE PROCEDURES ................................ 4-53 4.17 1000 HOUR (12-MONTH) INSPECTION & MAINTENANCE PROCEDURES ........ 4-63 4.18 2000 HOUR INSPECTION & MAINTENANCE PROCEDURES .............................. 4-66 4.19 5000 HOUR INSPECTION & MAINTENANCE PROCEDURE ................................ 4-73 4.20 MACHINE STORAGE .............................................................................................. 4-75

5. TRANSPORTATION 5.1 GROUND TRANSPORTATION ............................................................................... 5-3 5.1.1

MACHINE PREPARATION ............................................................................... 5-3

5.1.2

LOADING/UNLOADING THE MACHINE .......................................................... 5-5

5.1.3

SECURING THE MACHINE .............................................................................. 5-8

5.2 LIFTING MACHINE .................................................................................................. 5-10 5.3 INSTALLATION AND REMOVAL OF MIRROR FOR SAFETY................................ 5-12

6. SPECIFICATIONS 6.1 GENERAL SPECIFICATIONS ................................................................................. 6-3 6.2 SHOE TYPES........................................................................................................... 6-5 6.3 WORKING RANGES................................................................................................ 6-6 6.4 BUCKET AND ARM COMBINATIONS..................................................................... 6-8 6.5 LIFTING CAPACITIES ............................................................................................. 6-9

7. OPTIONAL EQUIPMENT 7.1 OPERATION OF HYDRAULIC BREAKER AND NIBBLER ..................................... 7-3 7.1.1

SELECTION OF HYDRAULIC BREAKER AND NIBBLER ............................... 7-3

7.1.2

BEFORE OPERATING BREAKER OR NIBBLER............................................. 7-3

7.1.3

PRECAUTIONS FOR IMPURITY AND HYDRAULIC OIL................................. 7-3

7.1.4

SWITCHING SELECTOR VALVE ..................................................................... 7-3

7.1.5

SETTING STOP VALVE.................................................................................... 7-5

7.1.6

BASIC OPERATION.......................................................................................... 7-6

7.1.7

PROHIBITED WORK IN USE OF BREAKER ................................................... 7-8

7.1.8

PERIODIC INSPECTION AND MAINTENANCE INTERVAL ............................ 7-11

7.1.9

REINFORCING ATTACHMENT ........................................................................ 7-11

7.1.10 PROHIBITED WORK IN USE OF NIBBLER ..................................................... 7-12 3

TABLE OF CONTENTS 7.1.11 PRECAUTION TO BE EXERCISED ON BREAKERS OF DIFFERENT MANUFACTURES ....................................................................... 7-14 7.2 PROPORTIONAL HAND CONTROL (EXTRA, NIBBLER AND BREAKER) ........... 7-16 7.2.1

BASIC OPERATION.......................................................................................... 7-16

7.3 PROPORTIONAL HAND CONTROL (NIBBLER AND BREAKER) ......................... 7-19 7.3.1

BASIC OPERATION.......................................................................................... 7-19

7.4 PROPORTIONAL HAND CONTROL (EXTRA)........................................................ 7-20 7.4.1

BASIC OPERATION.......................................................................................... 7-20

7.3 OBJECTS HANDLING ............................................................................................. 7-22 7.3.1

SAFETY PRECAUTIONS.................................................................................. 7-22

7.3.2

OBJECTS HANDLING OPERATION ................................................................ 7-23

7.3.3

DIAGRAM FOR THE READINGS OF THE LIFTABLE LOADS, LOCATED INSIDE THE CAB ............................................................................ 7-25

8. SPECIAL PROCEDURES 8.1 GENERAL ................................................................................................................ 8-3 8.2 RELEASING TRAVEL MOTOR BRAKES................................................................ 8-4 8.3 RELEASING SWING BRAKE .................................................................................. 8-7 8.4 LOWERING ATTACHMENT WHEN SUDDEN ENGINE FAILURE OCCURS ........ 8-11 8.5 HYDRAULIC TANK PRESSURE ............................................................................. 8-14

ATTACHMENT 1 - “EC” DECLARATION OF CONFORMITY

4

FOREWORD

FOREWORD

0-1

FOREWORD

0-2

FOREWORD

FOREWORD

AVOID INJURY Read, understand and follow all safety precautions and procedures found in this manual before attempting any operation, inspection or maintenance of this machine, attachment or systems. Manufacturer cannot anticipate every possible circumstance that might involve a potential hazard. The warnings in this publication and on the product are therefore not all inclusive. If a tool, procedure, work method or operating technique not specifically recommended by manufacturer is used, you must satisfy yourself that it is safe for you and others. You should also ensure that the product will not be damaged or made unsafe by the operation, lubrication, maintenance and/or repair procedures you choose.

GENERAL • •

• • • • • •

This manual contains procedures to aid the operator gain peak performance through effective, economical operation and maintenance of the machine.

Before operating the machine, operators must thoroughly read and understand all Safety, Operation and Maintenance instructions found in this manual. Failure to follow the instructions given in this manual may lead to serious injury to persons and or equipment failure.

Operators and persons working with this machine should continually study this manual until proper Safety, Operation and Maintenance procedures are completely understood.

This manual describes the basic operating techniques. Skill is gained as the operator utilizes these techniques and perfects them with an actual machine.

Some illustrated pictures may be different from your machine, as technical improvement is continuous, manuals are periodically updated to reflect these changes.

This manual may not contain attachments and optional equipment that are available in your area. Please contact an authorized Manufacturer Distributor for any optional attachments required.

The contents of this manual and operation of the machine are based on the use of genuine manufacturer sourced parts. Use of non-genuine replacement or modified parts is not recommended.

Materials and specifications are subject to change without notice.

PERIODIC INSPECTIONS •

After delivery of a machine, the Authorized Manufacturer Dealer/Distributor will make periodic service inspections. These inspections will be free of charge to the owner of the machine and will be at time intervals set by Manufacturer. Contact an authorized Manufacturer Dealer/Distributor for any Service related questions not explained in this manual.

NOTICE •

Owing to the policy of continual improvement, changes may be made by Manufacturer to any of its products without any obligation on the part of Manufacturer.

0-3

FOREWORD

KEEP OPERATION & MAINTENANCE MANUAL STORAGE

For quick reference, keep this manual in the magazine box of right rear of operator's seat.

READ THIS MANUAL BEFORE OPERATING THE MACHINE Most accidents occurring during work are due to non-observance of simple safety norms and elementary precautions.

Many accidents can be avoided if the causes are known and opportune cautions taken beforehand.

There is no device or protection, no matter how advanced, that many prove so effective at avoiding accidents as a careful and attentive behaviour.

0-4

FOREWORD

FOR ORDERING For ordering parts and service, inform an authorized Manufacturer distributor of your machine's Serial Number and Engine Serial Number stamped in the locations, and Hour Meter read, shown on the illustrations below. For future reference, record these Serial Numbers in the spaces provided below: MACHINE TYPE

MACHINE SERIAL No.

ENGINE SERIAL No.

. ENGINE SERIAL No.

. HOUR METER

. MACHINE SERIAL No.

0-5

HOUR METER

FOREWORD

0-6

1. SAFETY PRECAUTIONS

1

1. SAFETY PRECAUTIONS

1-1

1. SAFETY PRECAUTIONS

1-2

1. SAFETY PRECAUTIONS

1.1

GENERAL SAFETY INFORMATION

AVOID INJURY OR DEATH Do not operate or perform any maintenance on this machine until all instructions found in this manual have been thoroughly read and understood. Improper operation or maintenance of this machine may cause accidents and could result in serious injury or death. Always keep this manual in storage stored in the place provided on the machine.

If it is missing or damaged, place an order with an authorized dealer/distributor for a replacement.

If you have any questions, please consult an authorized dealer/distributor.

1. Most accidents, which occur during operation, are due to neglect of precautionary measures and safety rules.

Sufficient care should be taken to avoid these accidents. Erroneous operation, lubrication or maintenance services are very dangerous and may cause injury or death of personnel. Therefore all precautionary measures, NOTES, DANGERS, WARNINGS and CAUTIONS contained in this manual and on the machine should be read and understood by all personnel before starting any work with or on the machine.

2. Operation, inspection, and maintenance should be carefully carried out, and safety must be given the first priority. Safety messages are indicated using the following safety alert symbols and signal words. The safety information contained in this manual is intended only to supplement safety codes, insurance requirements, local laws, rules and regulations.

3. It is very difficult to forecast every danger that may occur during operation. However, safety can be ensured by fully understanding proper operating procedures for this machine according to methods recommended in this manual.

4. While operating the machine, be sure to perform work with great care to avoid damage to the machine, and accidents from occurring.

5. Continue studying this manual until all Safety, Operation and Maintenance procedures are completely understood by all persons working with the machine.

6. Symbols used in this manual; X (symbol): This symbol indicates an unacceptable practice or unsafe condition.

O (symbol): This symbol indicates an acceptable practice or safe condition.

7. Messages of safety appear in this manual and on the machine. All messages of safety are identified by the words "DANGER", "WARNING" and "IMPORTANT".

a.Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

AVOID INJURY OR DEATH

b.Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. c.Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. It may also be used to alert against possible damage to the machine and its components.

d.Special instructions or procedures which, if not correctly followed, may result in serious machine damage.

1-3

1

1. SAFETY PRECAUTIONS

1.2

SAFETY PRECAUTIONS

AVOID INJURY OR DEATH The proper and safe lubrication and maintenance for this machine, recommended by manufacturer, is outlined in this operator's manual for this machine.

Improper performance of lubrication or maintenance procedures are dangerous and could result in injury or death.

Read and understand this operator's manual before performing any lubrication or maintenance.

The serviceman or mechanic may be unfamiliar with many of the systems on this machine. This makes it important to use caution when performing service work. Knowledge of the systems and components is important before removal or disassembly of any component.

Because of the size of some of the machine components, the serviceman or mechanic should check the weights noted in this manual. Use proper lifting procedures when removing any components.

The following is a list of basic precautions that must always be observed.

1. Read and understand all Warning plates and labels on the machine before Operating, Maintaining or Repairing this machine.

2. Always wear protective glasses and protective shoes when working around machines.

In particular, wear protective glasses when using hammers, punches or drifts on any part of the machine or attachments. Use welders gloves, hood/goggles, apron and the protective clothing appropriate to the welding job being performed. Do not wear loose fitting or torn clothing. Remove all rings from fingers, loose jewelry, confine long hair and loose clothing before working on this machinery.

3. Disconnect the battery and hang a "Do Not Operate" tag in the Operator's Compartment. Remove key from starter key switch.

4. If possible, make all repairs with the machine parked on a level, hard surface. Block the machine so it does not roll while working on or under the machine. Hang a "Do Not Operate" tag in the Operator's Compartment.

5. Do not work on any machine that is supported only by lift, jacks or a hoist. Always use blocks or jack stands, capable of supporting the machine, before performing any disassembly.

6. Relieve all pressure in air, oil or water systems before any lines, fittings or related items are disconnected or removed. Always make sure all raised components are blocked correctly and be alert for possible pressure when disconnecting any device from a system that utilizes pressure.

7. Lower the bucket, blade (if equipped), or other attachments to the ground before performing any work on the machine. If this cannot be done, make sure the bucket, blade (if equipped) or other attachment is blocked correctly to prevent it from dropping unexpectedly.

8. Use steps and grab handles when mounting or dismounting a machine. Clean any mud, grease, oil or debris from steps, walkways or work platforms before using. Always face the machine when using steps, ladders and walkways. When it is not possible to use the designed access system, provide ladders, scaffolds, or work, platforms to perform safe repair operations.

9. Avoid back injury. Use a hoist when lifting components which weigh 23 kg (50 lb) or more. Make sure all chains, hooks, slings, etc., are in good condition and are the correct capacity. Be sure hooks are positioned correctly.

Lifting eyes are not to be side loaded during a lifting operation.

10.To avoid burns, be alert for hot parts and surfaces immediately after stopping the machine such as hot fluids in lines, tubes and compartment covers.

11. Be careful when removing cover plates. Gradually back off the last two bolts or nuts located at opposite ends of the cover or device and carefully pry cover loose to relieve any spring or other pressure, before removing the last two bolts or nuts completely.

12.Be careful when removing filler caps, breathers and plugs on the machine. Hold a rag over the cap or plug to prevent being sprayed or splashed by liquids under pressure. The danger is even greater if the machine has just been stopped because fluids can be hot.

13.Always use the proper tools that are in good condition and that are suited for the job at hand. Be sure you understand how to use them before performing any service work.

1-4

1. SAFETY PRECAUTIONS 14.Reinstall all fasteners with the same part number. Do not use a lesser quality fastener if replacements are necessary.

15.Repairs which require welding should be performed only with the benefit of the appropriate reference information and by personnel adequately trained and knowledgeable in welding procedures. Determine type of metal being welded and select correct welding procedure and electrodes, rods or wire to provide a weld metal strength at least equivalent to that of the parent metal. Disconnect battery before any welding procedures are attempted.

16.Do not damage wiring during repair/removal operations. Reinstall the wiring so it is not damaged nor will be damaged in operation of the machine by contacting sharp corners, or by rubbing against some object or hot surface. Do not connect wiring to a line containing fluid.

17.Make sure all protective devices including guards and shields are properly installed and functioning correctly before starting a repair. If a guard or shield must be removed to perform the repair work, use extra caution and replace the guard or shield after repair is complete.

18.Performing maintenance or repair work on the machine with the bucket/attachment raised is hazardous. The bucket/attachment and lift arm could fall and injure or kill a person. Be sure to lower the bucket or attachment to the ground before starting work on the machine.

19.Loose or damaged fuel, lubricant and hydraulic lines, tubes and hoses can cause fires. Do not bend or strike high pressure lines or install parts which are bent or damaged. Inspect lines, tubes and hoses carefully. Do not check for leaks with your hands. Very small (pinhole) leaks can result in a high velocity oil stream that will be invisible close to the hose. This oil can penetrate the skin and cause personal injury. Use a small piece of cardboard, wood or metal to locate pinhole leaks.

20.Tighten connections to the correct torque. Make sure that all heat shields, clamps and guards are installed correctly to avoid excessive heat, vibration or rubbing against other parts during operation. Shields that protect against oil spray onto hot exhaust components in event of a line, tube or seal failure must be installed correctly.

21.Do not operate a machine if any rotating part is damaged or contacts any other part during operation. Any high speed rotating component that has been damaged or altered should be checked for balance before reusing.

22.Be careful when servicing or separating the tracks (crawlers). Chips can fly when removing or installing a track (crawlers) pin. Wear safety glasses and long sleeve protective clothing. Tracks (crawlers) can unroll very quickly when separated. Keep away from front and rear of machine. The machine can move unexpectedly when both tracks (crawlers) are disengaged from the sprockets. Block the machine to prevent it from moving.

23.Caution should be used to avoid breathing dust that may be generated when handling components containing asbestos fibers. If this dust is inhaled, it can be hazardous to your health. Components in Manufacture products that may contain asbestos fibers are brake pads, brake band and lining assembles, clutch plates and some gaskets. The asbestos used in these components is usually bound in a resin or sealed in some way. Normal handling is not hazardous as long as air-borne dust which contains asbestos is not generated.

AVOID INJURY OR DEATH (In 5. Regard) Do not operate this machine unless you have read and understand the instructions in this operator's manual.

Improper machine operation is dangerous and could result in injury or death.

If dust which may contain asbestos is present, there are several common sense guidelines that should be followed. a. Never use compressed air for cleaning. b. Avoid brushing or grinding of asbestos containing materials. c. For clean up, use wet methods or a vacuum equipped with a high efficiency particulate air (HEPA) filter. d. Use exhaust ventilation on permanent machining jobs e. Wear an approved respirator if there is no other way to control the dust. f. Comply with applicable rules and regulations for the work place. g. Follow environmental rules and regulations for disposal of asbestos. h. Avoid areas where asbestos particles may be in the air.

1-5

1

1. SAFETY PRECAUTIONS

1.3

WARNING LABELS & DECALS

Warning labels and decals are affixed to the machine to remind operators and personnel of specific safety precautions in certain areas of the machine. The following are illustrated examples of all warning labels and decals along with their locations.

1.3.1 • • • •

WARNING LABELS & DECALS MAINTENANCE

Do not remove the attached warning labels and decals.

Confirm whether labels can be easily read.

If words or illustrations are illegible, clean off or replace the labels.

Use a cloth, water, and detergent to clean the labels. Never use organic solvents or gasoline.

If labels are damaged, missing or illegible, replace them with new ones.

Contact our dealer/distributor for new labels.

1.3.2

LOCATION OF WARNING LABELS & DECALS

18

19

16

24

23 22

20 VIEW II

II

21

VIEW I 7

3

2

17

15 10 I

III

11 8 5

9 6

1

4

13 14

1-6

12

VIEW

1. SAFETY PRECAUTIONS 1. DO NOT USE COUNTERWEIGHT LIFTING

DANGER

Located on counterweight.

Part Number - YN20T01221P1 (2REQ'D) Do not use counterweight lifting eyes to lift whole machine.

Lifting eyes can fall under this load resulting in personal injury.

Refer to operators manual for proper way of lifting machine.

1 2. WORKING ABOVE GROUND Located on hydraulic tank cover.

Part Number - ZL11N02604 There is a danger of falling when working on areas above ground.

•Do not approach edges.

•Use the appropriate equipment, such as ladders or platform when working above ground. In addition, strap yourself to the proper equipment accordingly.

•Avoid spillage of any oil or grease.

•Do not leave any tools around the working area.

•Use extreme caution to avoid slipping while walking.

•Do not jump on or from the machine. Use the steps and handrails and securely maintain a three point contact while mounting or dismounting at all times.

3. PRESSUREIZED HOT OIL

Located on hydraulic tank.

Part Number - YN20T01355P1 Pressurized hot oil can cause burns.

Depress cap slowly with engine off to relieve hydraulic tank pressure.

YN20T01335P1

4. HANDLING BATTERY Located on battery relay cover.

Part Number - YN20T01356P1 PREVENT BATTERY EXPLOSION

YN 2 0 T 0 1 3 5 6 P1

•Batteries give off hydrogen gasses that can explode and cause personal injury.

•Keep sparks, open flames and cigarettes away from batteries.

•Keep metallic articles away from batteries.

•Keep all ventilation caps tightly secured.

•Do not check change by placing metal articles across battery terminals.

•Leave battery box open to improve ventilation when charging.

•There is always the danger of burn and loss of eyesight due to the splashing of dilute sulfuric acid of battery. If skin and eye are accidentally splashed with dilute sulfuric acid, wash them with clean water immediately and have treated by doctor.

1-7

1. SAFETY PRECAUTIONS 5. SWING Located on each side of the rear counterweight.

Part Number - ZL11M04116 (2REQ'D) Do not enter in the swing area.

When the machine is swinging, be careful so as not to be caught the body between the upper structures.

ZL11M04116

6. BOOSTER CABLE

Located on battery relay cover.

Part Number - ZL11N01104 Electric hazard may cause injury when mishandling the cable.

Read operator manual for safe and proper handling.

ZL11N01104

7. HOT COOLANT

Z L11N0 0408

Located on top of engine food.

Part Number - ZL11M00408 Steam of hot coolant can cause injury or blindness.

Do not loosen or open radiator cap when coolant is hot and under pressure.

Before opening radiator cap: -Cool down engine completely.

-Cover radiator with cloth.

-Loosen cap slowly to relieve pressure.

8. ENGINE STOP

STOP ZL11M05108

Located on counterweight.

Part Number - ZL11M05108 Do not attempt any MAINTENANCE with engine running. Always stop the engine and allow machine to cool to avoid injury.Otherwise, there is a possibility of danger that your hand may be caught in the cooling fan or fan belt resulting injury.

Otherwise, there is a possibility of danger that your hand may be caught in the cooling fan or fan belt resulting injury.

1-8

1. SAFETY PRECAUTIONS 9. ADJUSTING TRACK TENSION Located on crawler frame.

Part Number - YN20T01813P1 (2REQ'D) •This work must be done carefully by two people. The operator must operate the machine as instructed by the signals of the partner.

The crawler belt is changed by lifting one side of the machine at a time. Unexpected lowering or movement of the machine can result in serious injury or death.

Do not operate the boom, arm or bucket / attachment while removing or installing a crawler belt.

Follow the instructions provided.

•Grease in track tensioning mechanism is under extreme pressure and can penetrate skin causing severe injury. Keep face and body away from grease fitting area. Do not loosen grease fitting more than one turn. If grease does not release after one turn of the fitting, call our dealer/ distributor for assistance.

Before removing the crawler belt, confirm that the pressure inside the track tensioning cylinder has been completely released. Then turn the sprocket.

If the procedure on releasing the pressure in the track tensioning cylinder is not followed, grease can penetrate skin causing severe injury. If the tension of crawler belt does not release, call the dealer/distributor for repair service.

YN20T01813P1

• •

10. HOT PARTS

Located on hydraulic pump cover.

Part Number - YT20T01351P1 Engine may be hot which could cause burns.

Do not touch engine until it cools down.

YT20T01351P1

11. ENGINE STOP Located on engine food.

Part Number - YN20T01363P1 Do not attempt any MAINTENANCE with engine running. Always stop the engine and allow machine to cool to avoid injury.

Otherwise, there is a possibility of danger that your hand may be caught in the cooling fan or fan belt resulting injury.

YN20T01363P1

Stop engine before servicing.

1-9

1

1. SAFETY PRECAUTIONS 12. MACHINE LIFTING Located on left side frame.

Part Number - YB20T01132P1

•Lift up the machine in the position as shown in right figure.

•The lifting up position shown in the figure is for the standard machine. For details, refer to the lifting procedure.

13. HANDLING GREASE GUN

CAUTION Located on engine dust cover.

Part Number - YT20T01287P1

14. HANDLING BATTERY

WARNING

Located on side of radiator duct.

Part Number - YN20T01854P1 A metallic tools and articles can cause explosion due to ignited by short-circuit batteries terminals. Do not put any metallic tools and articles over batteries.

15. PROCEDURE TO CHANGE SELECTOR VALVE

CAUTION

(NIBBLER AND BREAKER) Located on right side door.

Part Number - YT20T01285P2 (OPT.)

YT20T01285P2

1-10

1. SAFETY PRECAUTIONS 16. LOCK FRONT WINDOW AT THE HOUSED POSITION Located inside cab R.H. Part Number - ZL11M06008 Lock front window at the housed position.

There is always possibility of slipping down of the housed front window resulting in injury.

ZL11M06008

1

17. SWING BRAKE RELEASE SWITCH

YN20T01353P1

Located on rear cover.

Part Number - YN20T01353P1 While operating swing action, when the parking brake can not be released, set the toggle switch to "RELEASE" position, and the parking brake is released.

Usually, this toggle switch should be set to "NORMAL" position and contact our service shop immediately.

18. ELECTRICAL POWER LINES, READ OPERATOR'S MANUAL, LEAVING MACHINE Located inside cab R.H. Part Number - PV20T01005P1

PV20T01005P 1

•Contact with electrical power lines will result in severe injury or death.

Keep machine and attachment a safe distance from electrical power lines as per following instruction.

•Read Operator's Manual until it is understood perfectly.

Read Operator's Manual before operation, maintenance, disassembly, assembly and transportation without fail.

•Handling of safety lock lever.

There is always possibility of being caught, being run down and accident resulting in injury due to the unexpected movement of machine. Do not fail to put the attachment down on the ground, to lock the control lever and to take the key out when leaving from the machine.

19. BUCKET TO CAB CONTACT

Located inside cab R.H. Part Number - YN20T01350P1 Bucket can contact and damage cab when machine equipped with some attachments.

Check clearance between bucket and cab before operation.

Make sure when operating a bucket near cab.

YN 2 0 T 0 1 3 5 0 P1

1-11

1. SAFETY PRECAUTIONS 20. DO NOT PINCH YOUR HAND(S) Located on seat stand.

Part Number - ZL11M03708 Do not insert hand in the moving part.

There is a possibility of catching hand between the moving parts resulting in injury.

ZL11M03708

21. KEEP CLEAR WORKING AREA

Located on arm Part Number - ZL11M07508 (2REQ'D) Make sure the area is clear of obstacles and persons before begining the operation of the machine. Always look around before you start the swing operation. Make sure everyone is cleared in your worksite. Sound horn before beginning swing operation.

ZL11M07508

22. OPERATION BY FOOT PEDAL

CAUTION

Located inside cab R.H. Part Number - PY20T01062P1 (OPT.)

23. HANDLING CHANGE LEVER AND SELECTOR VALVE

CAUTION

(NIBBLER AND BREAKER) Located inside cab R.H. Part Number - YT20T01284P1 (OPT.)

1-12

1. SAFETY PRECAUTIONS 24. USE SUPPORT WHEN THE MACHINE IS LIFTED

Located inside cab R.H. Part Number - YN20T01351P1 To avoid hazardous condition, do not check or service when the machine is not supported securely.

-Place the attachment to the ground when you check or service on the machine.

-If you need the work keeping the machine lifting, support the machine securely with support or safety block.

YN 2 0 T 0 1 3 5 1 P1

1-13

1

1. SAFETY PRECAUTIONS

NOISE LEVEL Level of sound pressure at operator's compartment LpA = 70 dB (A) Level of constant level of sound pressure measured in the cab with door and windows closed and the heating/conditioning fan inoperative, measured on identical machine, in accordance with Standard ISO 6396:2008.

VIBRATION TO THE OPERATOR The level of vibrations transmitted to the operator depends mainly upon the conditions of the ground on whichoperations take place, the mode of operation of the machine and its equipment.

Thus, the exposure to vibrations can be considerably reduced when the following recommendations are compliedwith: - use equipment compatible with the machine and the type of work do be done; - adjust and lock the seat in the correct position; also inspect regularly the suspensions of the seat, performing theadjustments and repairs as required; - perform regularly the current maintenance operations of the machine at the prescribed intervals; - operate the equipment in a uniform manner, preventing, as far as possible, sharp movements or excessive loads; - when travelling, avoid, as far as possible, particularly rough terrain or the impact against possible obstacles.

This machine is equipped with an operator's seat complying with the requisites of standard ISO7096:2008.

This ensures that the exposure of the operator's body to vibrations comply with the protectionrequisites for the protection against vibrations when the machine operates as required by the operationalscopes, in accordance with the prescriptions of this Manual. The operator’s seat has been tested in accordancewith EM6 input spectral class and has a SEAT transmissibility factor < 0.7.

• The weighted average quadratic acceleration value to which the operator’s arms are subjected does not exceed2.5 m/s2.

• The weighted average quadratic acceleration value to which the operator’s body is subjected does not exceed0.5 m/s2.

These results were obtained using an acceleration gauge while digging ditches.

MERK: The Whole-Body exposure value is determined under particular operating and terrain conditions andtherefore may not be representative for all the possible operating conditions within the intended use of themachine. Consequently this single Whole-Body vibration emission value is not intended to determine theWhole-Body vibration exposure as required by European Directive 2002/44/EC. For this purpose it isrecommended to conduct working conditions measurement. If this is not feasible use of information providedin the table below from ISO/TR25398:2006 (*).

Basic emissions value

Standard deviation

1,4*aw,eqx

1,4*aw,eqy

aw,eqz

1,4*sx

1,4*sy

sz

[m/s2]

[m/s2]

[m/s2]

[m/s2]

[m/s2]

[m/s2]

Excavation

0,44

0,27

0,30

0,24

0,16

0,17

Hydraulisk hammer

0,53

0,31

0,55

0,30

0,18

0,28

Mine

0,65

0,42

0,61

0,21

0,15

0,32

Travel

0,48

0,32

0,79

0,19

0,20

0,23

Working conditions

(*) ISO/TR 25398:2006 Mechanical vibrations – Guidelines for assessment of exposure to whole-body vibration of rideonmachine – Use of harmonized data measured by international institutes, organizations and manufacturers.

1-14

1. SAFETY PRECAUTIONS

1.4

PRE-START SAFETY

A. FOLLOW THE RULE • In operating, inspecting and serving the machine, follow the precaution and procedure for the safety described in this manual.

• Never operate machine when being in poor physical condition, having taken medicine (making sleepy), being under the influence of alcohol and being mentally unstable.

• When working in group and with instruction by flagman, make sufficient previous arrangement about the working contents and operate the machine according to the specified signal.

B. WHEN FAILURE WAS DETECTED In operating or serving the machine, when the failure of machine (noise, vibration, smell, deviation of instrument, smoke, oil leaking and warning by warning device and multi-display) is detected, contact the person in charge immediately and take a proper measure. Do not operate the machine until the failure is removed.

C. WEAR PROTECTIVE CLOTHING

AVOID BURNS Work clothing that has come in contact with oil could catch fire. Change clothes immediately.

Wear well fitting safety shoes, hard hat, and working clothes, and put on protective glasses, face shield, ear protection and gloves. When necessary, wear reflective vest.

When operating attachments that produce flying debris, it is strongly recommended to purchase and install protective guards on the machine and close the all window to protect the operator from flying debris. Also the operator and all personnel in the area of the machine should wear protective gear such as safety shoes, hard hat, gloves and face shield or goggles.

D. PREPARE FOR EMERGENCIES Have a fire extinguisher and First Aid Kit ready for emergencies. Know how to operate the fire extinguisher and know where the First Aid Kit is located for easy access in case of emergency.

Prepare beforehand the communication means in case of any emergency, and take note of telephone numbers for emergency contact.

E. PRECAUTION TO BE TAKEN WITH DEVICES FOR SAFE • Check that all protective guard and cover, and mirror are installed properly. If the failure is found, repair it immediately.

• Well understand how to use the device for safety.

• Never remove the device for safety and control it so that it always functions correctly.

1-15

1

1. SAFETY PRECAUTIONS F.

TAG OUT MACHINE DURING MAINTENANCE

Before performing any inspection or maintenance procedures to the machine, post to the operators controls a "DO NOT OPERATE" tag to warn persons not to start the machine. Inform the supervisor and all operators that the machine is under inspection or maintenance and they will be informed when the machine is ready for normal operation.

Order tag P/No. YN20T01320P1

G. ENSURE SAFETY AT THE WORKSITE • Know the work area! Before operating the machine, carefully survey and record the land and worksite features to prevent the machine from falling or the soil from caving in.

• It is dangerous to allow other personnel to enter into the working area.

Make the working area off-limits to other people by providing barricades.

Provide a flagman in working areas with heavy traffic to avoid accidents.

H. ENGAGE SAFETY LOCK LEVER BEFORE LEAVING MACHINE Before leaving the operator's seat, move the safety lock lever to the "LOCKED" (Up) position. This will not allow operation of any hydraulic controls should they be accidentally moved. If the lever is not set to the "LOCKED" position and hydraulic controls are touched accidentally, the machine may move suddenly resulting in serious injury or death.

Before leaving the machine, lower the bucket to the ground, place the safety lock lever in the "LOCKED" (Up) position, stop the engine and remove the key from the starter key switch.

A. Locked position B. Unlocked position

1 A

B

I. SIGNS, SIGNALS & FLAGMEN Install signs on soft shoulders and ground areas, and have a flagman direct the operation if necessary. The operator should note marks and follow signals from the flagman. All personnel should know the meaning of the signs, marks, and signals. Only one flagman should give the signs and signals.

J.

CLEAN THE MACHINE

Keep the machine clean and free of debris, excess or spilled lubricants, fuel and fluids. Use approved solvents, detergents and water to clean the machine and its components on a regular basis.

Be careful not to allow water to reach components. Serious damage can occur to the system by allowing water to reach the components. Never clean inside of cab, or components with pressurized water or steam.

electrical electrical electrical electrical

1-16

1. SAFETY PRECAUTIONS K. KEEP THE AREA AROUND THE OPERATOR SEAT CLEAN • When taking the operator's seat, do not fail to remove mud, grease and oil, etc. on the sole of shoes. The sole with mud, grease and oil, etc. might slip on the pedal when operating resulting in accident.

Do not leave parts and tools in the area around the cab.

• Do not leave plastic bottle inside of the cab and put suction cup on the window glass.

They may do the same job as lenses introducing the possibility of fire.

• Do not take dangerous substances like combustibles and explosive substances into the cab.

• Do not use radio and cellular phone in the cab in traveling operation and working operation.

• After using the ashtray, put out the fire of matches and cigarettes without fail and close the cover.

• Do not leave cigarette lighter inside of the cab. There is a possibility of fire due to high temperature.

L. HOW TO HANDLE LIFE HAMMER A life hammer is provided on the right side of cab. In case of emergency, take the life hammer, break the cab glass, and escape from the cab.

In addition, the life hammer is equipped with a cutter on the lever side to cut the seat belt, etc.

For the emergency escape way, see "2.3.14 EMERGENCY ESCAPE FROM CAB" in Chapter 2.

M. FIRE PREVENTION Fire due to Fuel and Oil There is a possibility of catching fire by bringing fire near inflammables like fuel, oil, antifreeze mixture, window washer, etc.

Follow precaution described below.

• • • • • • • • • •

Do not smoke close to the area and do not use the fire near the area.

Make up shortage of fuel after stopping the engine.

During making up shortage of fuel and oil, do not leave the place.

Tighten caps for fuel and oil securely.

Make sure not to spill out oil on the heated surface and the parts for electric system.

Store fuel and oil in the specified place and keep out of the area excluding persons concerned.

After refueling and lubrication, wipe off the spilled out fuel and oil, etc. immediately.

Move the inflammables to the safe area before carrying out the grinding and welding works of machine.

Use incombustible washing as wash oil for parts, etc. and do not use light oil and gasoline which might catch fire.

Do not weld the pipes and tubes containing combustible liquid and do not employ gas cutting.

1-17

1

1. SAFETY PRECAUTIONS Fire due to Faulty Electric Wire The fire may be caused by short-circuit of electric wire.

• Keep all connectors of electric wire clean and fix them securely.

• Check the wire for loosening and damage every day, and tighten loose connectors and clamps for wiring again and replace the damaged wire with new one.

Fire due to Faulty Piping Check that the clamp, guard and cushion of hose and tube are securely fixed. The loosening may cause the damage of hose due to the vibration during operation and the scrubbing in contact to other parts and is in danger of fire and accident resulting in injury and death due to the spouting out of high pressure oil.

Use Approved Work Lights Use only approved work lights when performing inspection and maintenance procedures to prevent possible fire or explosion. Certain types of work lights should not be used due to the possibility of ignition of certain flammable gasses and fluids from the machine.

Measures to be Taken at the Time when Fire Occurred When the fire occurred, escape from the machine according to the following way.

• Turn starter key switch off to stop engine.

• Carry out the early fire fighting with extinguisher if the spare time is left.

• Escape from the machine making use of hand rail and step.

N. PRECAUTION TO BE TAKEN AT THE TIME WHEN GETTING ON AND OFF MACHINE • •

•

• • •

Getting on and off the machine from the side where the step and hand rail are provided.

Before getting on and off the machine, check the step and hand rail for damage and loose bolts. If damage and loose bolts are found, repair them.

And if grease and oil, and mud adhered on the hand rail and step are found, remove them completely.

When getting on and off the machine, do not fail to use the hand rail, step and crawler shoe faced to the machine and support the body at three points.

There are many people injured by jumping from the machine. Never jump from the machine.

Do not get on and off the running machine.

Do not use control lever and safety lock lever for getting on and off the machine.

Do not get on and off the machine while holding tools by hand.

O. PERSON ON THE ATTACHMENT IS NOT ALLOWED Do not ride person on the attachment. There is a possibility of serious injury or death like falling from the machine.

P.

PAY ATTENTION TO THE NOISE

The large noise from the surrounding might cause hard hearing and deafness. If it is unavoidably necessary to enter in noisy area for long time, do not fail to wear protectors or earplugs.

1-18

1. SAFETY PRECAUTIONS Q. USE THE PROPER OPTIONAL ATTACHMENT Use only optional attachments designed for and approved by manufacturer. Read, understand and follow all instructions in the manual accompanying the optional attachment. Use of any optional attachment not approved by manufacturer in writing, can cause serious injury to personnel, damage to the machine and its components and shorten the life of the machine.

Contact an authorized our distributor for optional attachments available for the machine.

R. CAUTION TO MODIFICATION Machine modification is allowed only when our distributor approves it. Unauthorized modification may cause injury or death. Unauthorized modification voids the machine warranty.

When any modification is intended, consult with the authorized dealer/distributor.

S. PAY ATTENTION TO FALLING MATERIALS AND FLYING DEBRIS At the site where there is a possibility of falling material and flying debris, provide protective guard on it as required to protect operator from possible risks.

•

• •

•

Provide front guard (in option) on it at the time of hydraulic power breaker work, demolition work, and cutting work.

In working operation, do not fail tot close the front window and door.

At the sites like mine and quarry stone, etc. where there is a possibility of falling stone, do not fail to wear head guard (in option).

When working at the site where there is a possibility of falling materials and flying debris, person other than operator must take enough distance from falling stone and flying debris.

T. PERFORM PRE-START INSPECTION Walk around the machine before starting the machine, perform a PRESTART inspection of the machine and make note of any abnormality. If any problems are found, repair or replace defective components immediately. DO NOT OPERATE THE MACHINE until all problem areas are properly repaired. Always keep the windshield, work lamps, and mirrors clean for good visibility.

1-19

1

1. SAFETY PRECAUTIONS U. ADJUSTMENT OF OPERATOR'S SEAT Adjust the operator's seat to the body of operator and the working contents, or operator might be tired causing accident.

• •

When operator changes, adjust the operator's seat without fail.

In the condition where operator's back is fitted to the seat back, press pedal fully and check that the control lever, pedal and switch can be properly manipulated.

1-20

1. SAFETY PRECAUTIONS

1.5

SAFETY DURING OPERATION

A. STARTING ENGINE

When the caution tag "Do not operate" or similar warning is indicated on the control lever or in the area around the cab, do not start engine and do not touch the control lever.

1

B. PASSENGERS This equipment is not intended or designed for the transportation of persons. Do not allow persons to ride on the machine. Serious injury or death can result from allowing passengers on or in the machine.

C. • • • •

SAFETY CHECK IN THE SURROUNDING BEFORE OPERATION Check that no one is in the area around the machine.

Fix the door and window securely even though they are open or closed.

Adjust the mirror to the position where the operator can see well the rear sight.

For the adjustment, refer to "Adjusting Mirror" in Chapter 3.

Check that the alarm system like horn and travel alarm (if equipped) functions properly.

D. FASTEN SEAT BELT Fasten seat belt so as to prevent receiving heavy blow inside of cab, being thrown out of the cab and being crushed under the machine at the time when the machine turned over. If not fastened, it causes serious injury or death.

Fasten seat belt without fail whenever taking the seat.

• Check the attaching bracket and attaching belt for possible failure before fastening the seat belt.

• Replace seat belt at least every 3 years even though no damage is found.

E. • • • •

PRECAUTION TO BE TAKEN WHEN STARTING ENGINE Lock it with the safety lock lever.

Sound the horn before starting the engine to alert people that the machine is being started.

Start engine from the operator's seat.

Do not short circuit the starter circuit or battery to start the engine. This may cause serious injury or cause damage to the electrical system.

F. CHECK AFTER STARTING ENGINE Check the machine for proper operation after starting the engine. Slowly cycle attachments, swing, and travel functions in an area with sufficient space, without obstacles and personnel. Failure to do so could result in injury, death or machine damage. If any problems or damage is found on the machine, repair immediately.

G. WARM UP ENGINE AND HYDRAULIC OIL BEFORE OPERATION Take time to warm up the engine and hydraulic oil especially during cold season. In cold conditions, response of machine control is slow. This may cause injury, death or machine damage.

H. CONFIRM OPERATING CONTROL PATTERN Slowly operate the control levers to confirm the operating patterns in advance. Make sure the operation control pattern is according to the indication plate.

1-21

1. SAFETY PRECAUTIONS I.

CONFIRM TRAVEL DIRECTION

Before starting the machine, check the position of front idler (1). In the proper travel position, the front idler (1) is positioned on the front side and travel motor (2) is on the rear side.

1

2

J. PROHIBIT RAPID LEVER OPERATION IN TRAVEL • The rapid travel operation like urgent start is prohibited.

• The rapid lever change from forward to reverse (from reverse to forward) is not allowed.

• The rapid lever operation like urgent stop from the speed close to the maximum is not allowed.

K. DO NOT HIT CAB WITH ATTACHMENT Check clearance between bucket and cab before operation. Slowly cycle bucket, check for interference with arm and cab, particularly if a lifting eye is welded on bucket bottom. Exercise care when operating the bucket near the cab.

L. PRECAUTION TO BE TAKEN IN TRAVEL The firm and level ground must be used for traveling. And select the road in straight and large radius curve as much as possible, do not take sharp pivot turn and spin turn. In narrow area, swing the wheel in the opposite direction as many times as possible.

•

• • •

When running, keep the attachment in the position the height from the ground is 30 to 40 cm (1 to 1.3 ft) as shown in the figure.

The abrupt control lever operation and pedal operation are not allowed.

When traveling on rough terrain, travel at slow speed.

Travel the machine while keeping away from the obstruction as much as possible.

If it is unavoidably necessary to get over the obstruction, travel at slow speed while keeping the position of attachment close to the ground.

1-22

30~40cm (1~1.3ft)

1. SAFETY PRECAUTIONS M. TRAVELING ON SLOPE The traveling up and down on a slope 30 degree in angle or more is not allowed because there is a possibility of rollover.

•

When traveling up and down on a slope, keep the attachment at the height of 20 to 30 cm (0.7 to 1 ft) from the ground so as to make the urgent stop possible at the time of emergency by putting the attachment down to the ground. And when traveling down the slope, travel at further slow speed.

1

20~30cm (0.7~1ft)

Traveling up on a slope •

Reduce the speed when traveling on the grass and fallen leaves, and wet iron plate because it is easy to skid.

20~30cm (0.7~1ft)

Traveling down on a slope

•

When traveling up the slope, extend the front attachment to take the balance while keeping the height at 20 to 30 cm (0.7 to 1 ft) from the ground, and travel at slow speed.

20~30cm (0.7~1ft)

Traveling up on a slope

1-23

1. SAFETY PRECAUTIONS N. PRECAUTION TO BE TAKEN IN TRAVELING ON THE SLOPE When traveling on a slope, be careful of turning over and skidding.

Keep the bucket at the height of 20 to 30 cm (0.7 to 1 ft) from the ground in order to make putting it down to the ground at emergency possible. Do not turn the direction and go across on a slope, but go down to the flat space and take a detour-route for safety.

•

Do not travel on a slope that the slope angle is 30 degree or over. And do not traverse a slope that the slope angle is 15 degree or over.

O. OPERATING ON INCLINES OR SLOPES •

•

•

Operation of this machine on an incline or slope may cause the machine to become unstable or unbalanced.

Work up and down inclines or slopes, do not across.

Do not swing or turn machine around on a slope. Build a level area for the machine to operate. Operate controls carefully to prevent sudden movements which may cause the machine to slide or rollover.

When the engine was stalled, put down the bucket on the ground and return every lever to the neutral position, then start the engine again.

Even if the swing operation is stopped on a slope, the machine might swing by the machine’s own weight.

Operate the machine carefully when you operate the machine on a slope.

Place the bucket to the ground when you park the machine by necessity on a slope.

P. FROZEN & SNOW COVERED WORK SITES Use extreme caution when operating the machine on frozen or snow covered work sites. Operate all controls slowly and cautiously to prevent sudden movements such as start/stop/turn, that may cause the machine to unexpectedly shift, slide or move. Even on the slightest slope, when snow is present or work area is frozen can allow a machine to unexpectedly move. Snow on shoulders or snow drifts can be much deeper than expected. The machine can easily become buried under such conditions. Use extreme caution while operating the machine around or in snow.

Be careful for frozen ground that becomes soft along with the increase of ambient temperature.

1-24

1. SAFETY PRECAUTIONS Q. SWING / TRAVEL FUNCTION Make sure the swing and travel area of machine is clear of all persons and obstacles before operating swing/travel controls. Sound horn before operating swing/travel machine. If necessary, have a flagman signal operator during operation to prevent injury to persons or damage to obstacles and equipment.

1

R. WORKING AROUND UNDER GROUND UTILITY LINES During operation it is likely that you will be working around or near buried utility lines which may include, but are not limited to: - Electrical Power Line - Gas Line - Water Line - Communication Line: Telephone or Cable Television Before begining any trenching, drilling or other construction work it is your responsibility to be aware of all such utility lines buried in the area of your project and to avoid them.

ALWAYS have all local utility companies mark the location of their lines.

Check with local authorities for laws, regulations and/or strict penalties requiring you to locate and avoid existing utilities.

S. RESTRICTED WORK AREAS In work sites with limited height and swing / traveling areas such as tunnels, bridges, around electrical power lines, other utilities, or inside structures. Use extreme caution on work sites with limited height and swing/ traveling areas such as tunnels, bridges, around electrical power lines, other utilities or inside structure. Keep the machine and its attachment a safe distance to prevent injury, death or damage on equipment or structure.

Use a flagman to guide the operators.

1-25

1. SAFETY PRECAUTIONS T.

DO NOT WORK UNDER PRECIPICE / OVERHANG

Do not dig under the precipice. It may cause falling rocks or loosening of the precipice resulting in injury, death or machine damage.

U. CHECK THAT NO PERSON IS UNDER THE BUCKET There is a possibility of accident resulting in injury or death and the damage of machine due to the fall of sand/earth and the direct contact with bucket when the bucket and attachment pass through over the worker and the driver's seat of dump truck. Do not pass the bucket through over person for safety.

V. GROUND STABILITY Make sure the condition of the work site is stable and capable of supporting the machine weight during operation. Do not operate attachment too close to the machine. Operation of the machine on shoulders or filled areas could cause the machine to become unstable presenting a work hazard. Position the crawler at right angle to shoulder and the travel motors to the rear of the machine, allowing for quick reversal, should the work area become unstable.

1-26

1. SAFETY PRECAUTIONS W. SAFETY LOADS LIFTING •

•

• • •

• • • •

The excavator is a machine designed specifically to perform digging/loading works, thus it must not be used to handle suspended loads. In the event, under exceptional conditions, it becomes necessary to handle materials, the following indications must be strictly implemented: The machine must be equipped compulsorily with the appropriate variant provided upon request. Also, totally comply with the safety precautions for the operation of the excavator as a lifting equipment.

Secure the loads to be raised using cables or chains fastened with appropriate hooking mechanisms.

Do not hook cables or chains to the bucket teeth.

Nobody should be allowed to remain under the raised load or within the excavator operating range for any reason whatever.

Do not exceed specified lifting capacity. Incorrect fastening of slings or chains may cause boom/arm failure or failure of the lifting means with consequent bodily injuries and even death.

Always ensure that slings and chains used for lifting are adequate to the load and in good condition.

All lifting capacities are referred to the machine on a level surface and should be disregarded when working on a slope.

In any case, comply with the current national or local regulations on this matter.

X. WORKING AROUND UTILITIES If it is suspected that utility lines such as, gas, water, phone or electrical power are in the work area, contact the local utility authority for line location BEFORE beginning work in the area. Use extreme caution around electrical power lines. Keep a sufficient distance away from electrical lines during operation. See chart below for minimum distances.

LINE VOLTAGE 0 ~ 50,000

MINIMUM DISTANCE-m (feet) 3.0 m (10) or more

50,000 ~ 200,000

4.5 m (15) or more

200,000 ~ 350,000

6.0 m (20) or more

350,000 ~ 500,000

7.5 m (25) or more

500,000 ~ 750,000

10.5 m (35) or more

750,000 ~ 1,000,000

13.5 m (45) or more

Y. SET LIMITS TO WORKING AREA Set limits around the working area to avoid collision, injury or death. Check for obstacles and personnel while swinging. Use a flagman to guide the operator whenever necessary.

1-27

1

1. SAFETY PRECAUTIONS Z. CAUTION FOR WORK IN URBAN AREAS It is dangerous to allow other personnel to enter into the working area.

Make the working area off-limits to other people by providing barricades.

Provide a flagman in working areas with heavy traffic to avoid accidents.

AA. WORK WITH SUFFICIENT LIGHTING When working in dark places, turn on the work lamp. And if required, provide additional lighting facilities to assure good visibility.

Stop working when it is impossible to ensure the visual field due to fog, snow or rain.

BB. SLIPPERY OPERATION SURFACE Use caution when operating machine on boards or steel plates. Boards and steel plates become very slippery when wet.

Pay special attention when working on inclined areas.

Provide a device to prevent skidding and operate with extra care. Piled up tree leaves or branches also may causes skidding.

CC. STRENGTHEN SOFT GROUND When working on a soft ground or marshy area, the machine may sink.

Be aware that frozen ground becomes soft with the increase of ambient temperature.

Use logs or lumber positioned in the opposite direction of the track to prevent the machine from sinking.

DD. LOOSE / UNSTABLE GROUND AFTER RAIN Be careful for the possibility of machine rollover after rain.

The vibration and weight of the machine could cause shoulder of road or pathway to become loose or unstable.

Inspect the areas where the machine will travel and operate on to assure safe operation is possible.

Pay attention for possible loosened precipice/overhang or shoulder of road, and falling rocks. Always pay attention for unexploded dynamite on job sites where dynamite is used.

EE. SAFETY CHECK IN PARKING MACHINES When the machine is not parked properly, there is a possibility of unexpected overrun, risks due to barbarous act and dangerous movement at the time of the coming start.

Park the machine following the safety parking procedure shown below.

• • • • • •

Park the machine on the firm and level ground to prevent overrun.

Put the working equipment like bucket and dozer (if equipped) on the ground.

Secure the safety lock lever to "LOCKED" position.

Perform the cool-down operation of engine at low idling for 5 minutes.

Stop the engine by switching the starter key switch off and then take out the key.

When leaving from the machine, close the window, door of cab and all doors and covers and lock them.

1-28

1. SAFETY PRECAUTIONS

1.6

INSPECTION & MAINTENANCE SAFETY

A. READ CAREFULLY OPERATING/MAINTENANCE PROCEDURES Incorrect maintenance may cause not only damages on the machine, but also injury.

Read and fully understand the maintenance procedures and safety precautions described in the operation and maintenance manual before performing any maintenance in this machine.

B. CONFIRM UNDERSTANDING OF HAND SIGNALS AND COMMUNICATION USED ON JOB SITE Have a meeting before starting work on the job site. Confirm all workers understand all hand signals, flag signals and other means of communication used on the job site to avoid any accidents or injuries.

C. ORGANIZE AND CLEAN UP WORKING AREA Organize and clean up the working area.

Remove any obstacles and also remove any grease, oil, paint, broken pieces, etc., from the working area to avoid injury.

D. "TAG-OUT" MACHINE Before performing any inspection or maintenance procedures to the machine, fill out and post to the operator's controls a "DO NOT OPERATE" tag to warn persons not to start the machine. Also inform the supervisor and all operators that the machine is under inspection or maintenance and they will be informed when the machine is ready for normal operation.

E. TOOLS & EQUIPMENT Use the proper tools and equipment for the task at hand. Know the proper use of the tools and equipment before starting any inspection or maintenance procedures.

F.

PRESSURIZED FLUIDS & LUBRICANTS

Always release pressure from hydraulic reservoir, engine coolant, fuel system and all systems containing pressure before removing any caps or components. Be cautious of hot fluids and gasses from systems on machines that have just been stopped. Allow sufficient time for systems to cool before performing any inspection or maintenance procedures.

G. AVOID HOT SURFACES & AREAS Immediately after the machine is operated, the temperature and pressure of the engine coolant, engine oil and hydraulic oil are very high. Burns may result if caps are removed, or oil, water, or filters are changed under these conditions. Wait until the temperature goes down, before attempting to check fluids or change filters.

1-29

1

1. SAFETY PRECAUTIONS H. HYDRAULIC PRESSURE Under normal conditions, all circuits of the hydraulic system are under extreme pressure.

When inspecting for leaks, use a small piece of cardboard, wood or metal to locate leaks. Small (pinhole) leaks can be dangerous if contact with skin or eyes is made.

Wear approved safety glasses or face shield, gloves, hard hat, safety shoes and work clothes during all inspection and maintenance procedures. Seek immediate medical assistance if injury occurs.

I. RELIEVE THE HIGH PRESSURE IN FUEL LINE The engine fuel line generates high pressure in operation. In checking and servicing the fuel line, wait for 30 seconds to start checking and servicing until the internal pressure is released.

J.

STOP ENGINE

Do not attempt any MAINTENANCE with engine running.

Always stop the engine and allow machine to cool to avoid injury.

Otherwise, there is a possibility of danger that your hand may be caught in the cooling fan or fan belt resulting injury.

If it is unavoidable to operate the engine for inspection or maintenance, carry out the work with two people.

The person seated in the operator's seat should be ready to stop the engine at any time while watching for a signal from the other person.

K. VENTILATION PRECAUTIONS Operation of the machine indoor or in a place with poor ventilation may cause poisoning by gas.

Ventilate any exhaust gas, fuel, cleaning oil, paint or similar articles.

Make sure there is proper ventilation in the working area when the machine is operated indoors. Provide a ventilating fan, if required.

L. REMOVING AND INSTALLING ATTACHMENTS, AND STORING ATTACHMENTS • •

Remove and install attachments after appointing a man to supervisor in advance.

The attachment in danger of falling should be stored in the stable condition where supported in order not be fallen. And entry into the stored area of person other than the person concerned is prohibited.

1-30

1. SAFETY PRECAUTIONS M. USE SUPPORT EQUIPMENT DURING SERVICE

• •

When machine inspection or maintenance is done under the boom, arm or under the bucket/attachment use proper equipments or blocks to secure the attachment.

The work in the condition where the crawler is floated by arm and boom causes the danger of falling of the machine if the control lever is shifted unexpectedly or the piping is broken.

No one is admitted to enter under the unstable machine.

N. WORKING ABOVE GROUND There is a danger of falling when working on areas above ground.

• •

• • • •

Do not approach edges.

Use the appropriate equipment, such as ladders or platform when working above ground. In addition, strap yourself to the proper equipment accordingly.

Avoid spillage of any oil or grease.

Do not leave any tools around the working area.

Use extreme caution to avoid slipping while walking.

Do not jump on or from the machine. Use the steps and handrails and securely maintain a three point contact while mounting or dismounting at all times.

O. DO NOT DROP OFF TOOLS AND PARTS Dropping of any tools and parts in the working area may cause injury or faulty machine operation.

Do not leave any tools or articles in the working area or component compartment. Store all tools properly when the work is completed.

P. GENERAL GUIDELINES FOR WELDING Welding work must be performed by a certified welder with sufficient experience. In addition, safety practices must be followed by any personnel involved in such work. Identify all cracks to be repaired or areas to be welded by thoroughly cleaning the suspected surface, remove paint, and check with dye penetrant or magnetic particle testing. The life expectancy of the welded area depends on the work quality and the attention given to details during welding.

• Turn starter key to "OFF" position.

• Remove negative (-) cable from battery terminal to turn off the current.

• Attach welder ground cable with 1 m {3.3 ft} from component being welded.

If grounding cable is attached near electric parts/connectors, these electric parts/connectors may cause damaging.

• Attach welder ground cable near the weld area. Futhermore, the cable attached are is to be positioned at the same welding area.

• Make sure that neither bearing nor seal are there between the welder ground and the weld area.

• Do not attach the welder ground cable to the near attachment pin and/or cylinder. It causes the damage of plating.

• Remove paint from any surface to be welded. Painted surfaces produce unhealthy gasses when welded.

• Always wear protective clothing appropriate to the welding, and use protective equipment for the welding job.

• Perform work in a well ventilated areas.

• Clear the flammable items and provide the fire extinguisher.

1-31

1

1. SAFETY PRECAUTIONS

AVOID FIRE HAZARDS -Provide a fully charged fire extinguisher at all times while performing grinding, heating, or welding.

-Clean oil and/or flammable materials from any surface to be cut.

-Protect all flammable parts and surfaces from sparks and/or flames Perform work in a well ventilated area.

-Keep sparks and flames away from paint and/or solvent.

-Keep away sparks and flames from cylinder rods, seals, electrical wires, and/or hydraulic hoses.

Q. CRAWLER SHOE TENSION •

•

Grease in track tensioning mechanism is under extreme pressure and can penetrate skin causing severe injury.

Keep face and body away from grease fitting area.

Do not loosen grease fitting more than one turn.

If grease does not release after one turn of the fitting, call our dealer/distributor for assistance.

YN20T01813P1

R. CRAWLER BELT/TRACK TENSION The grease used to adjust the crawler belt tension is under extreme pressure in the cylinder. Use extreme caution when adjusting crawler belt tension. KEEP FACE, HANDS AND LEGS AWAY FROM THE GREASE FITTING AREA. Carefully and slowly loosen the grease fitting when lessening crawler belt tension. Never loosen grease fitting more than one complete turn.

See 4-39 for the procedures to adjust the tension of the crawler belt/track.

S. PAYING ATTENTION TO BROKEN PIECES WHEN HAMMERING Flying debris may cause injury when hammering hard metal parts, such as pin, edge, tooth, bearing, etc.

Wear protective clothes such as protective glasses, safety hat, etc. during maintenance.

T. • • • •

PAY ATTENTION TO REFRIGERANT OF AIR-CONDITIONER When inhaled refrigerant of air-conditioner carelessly, it will exert deadly effect to the human body.

Do not bring fire near the area where the air conditioner is serviced and gas is generated.

Use recovery recycling system to prevent cooling medium from escaping into atmosphere.

Do not loosen the parts for refrigerant circuit because there is a possibility of loss of eyesight and frostbite by getting refrigerant in eyes and by directly touching it by hand.

1-32

1. SAFETY PRECAUTIONS U. DO NOT HEAT HYDRAULIC EQUIPMENT OR PIPING Do not apply heat to hydraulic equipment or piping, such as welding, soldering, heating with torch, etc.

Heating of hydraulic components or piping will cause gas expansion, which can easily catch fire and/or explode.

•

•

•

Do not heat the section close to the tube and hose contained pressurized oil or other flammable materials by welding, soldering and torch.

If the pressurized tube and hose is heated directly, they may be suddenly cut. When carrying out the welding and soldering works, cover the tube, hose, and other flammable materials with fire-proofed cover for fire prevention.

Before welding and gas cutting, remove flammable fluid completely with nonflammable solvent.

V. AFTER COMPLETION OF MAINTENANCE WORK Check machine for proper functioning when any maintenance is completed: • After any maintenance work is completed, operate the engine at low idle, and check for leakages and abnormalities.

• Slowly operate each machine function to confirm proper operation.

• Increase the engine speed gradually, and again check for leakages and abnormalities.

• Operate each control lever carefully for smooth operation.

W. DISPOSE OF WASTE PROPERLY Dispose of oils, fuel, coolant, solvents, filters, batteries etc. according to federal, state and local codes and regulations regarding hazardous waste disposal. Contact local authorities for proper disposal methods of such materials.

1-33

1

1. SAFETY PRECAUTIONS

1.7

BATTERY SAFETY

A. WEAR PROPER PROTECTIVE CLOTHES Wear long sleeve shirt, gloves and approved safety glasses or face shield when working with or around batteries. Battery electrolyte (acid) will cause severe burns if allowed to make contact with clothing, skin or eyes.

Should electrolyte (acid) come in contact with clothes, skin or eyes, immediately remove effected clothing, flush area with clean water for 15 minutes and get prompt medical attention.

B. KEEP AWAY FROM FIRE OR FLAMES Do not allow batteries in the vicinity of fire or flames and do not smoke when working with batteries. Explosive hydrogen gas is produced by the electrolyte (acid) in the batteries. Always work with batteries in a well ventilated area.

C. CHARGING BATTERY Charge the battery in a well ventilated area. When charging battery, remove cell caps to allow gasses to escape.

Avoid breathing gasses from battery.

• •

Do not charge the frozen battery.

There is the danger of explosion. When the battery is frozen, warm it to 16 degree C or higher.

Do not use and charge the battery of which the liquid level is lower than the lower limit. This may cause explosion. Check the battery liquid level periodically, and make up the battery liquid loss with distilled water to proper limit of the liquid level.

1-34

1. SAFETY PRECAUTIONS D. USING BOOSTER CABLES •

• •

• • •

If using another machine or vehicle to boost Cable connecting order Cable disconnecting order discharged batteries, make sure that the machine or vehicle DOES NOT TOUCH the disabled machine.

(Red) Before connecting booster cables, confirm the positive (+) and negative (-) terminals of the booster battery.

Tighten the battery clamps of the positive (+) and negative (-) terminals on the booster battery and the disabled machine before connecting booster cables.

Connect the positive (+) cable first, then connect negative (-).

Booster battery Discharged battery When disconnecting, disconnect the negative (-) cable (Black) first, then disconnect the positive (+) cable To the upper frame of the troubled machine Refer to BASIC MACHINE OPERATION section of this manual for proper procedures for use of booster cables.

EXPLOSION HAZARD Improper booster cable connections can cause an explosion resulting in personal injury.

Connect booster cables using following procedure.

1.

Connect booster cable to positive (+) battery terminal of discharged battery. Connect other end of booster cable to positive battery terminal of normal battery.

2.

Connect other booster cable to negative (-) battery terminal of normal battery. Connect other end of booster cable to upper frame of troubled machine.

3.

Start engine and remove booster cables in reverse order.

OTHER PRECAUTIONS • Pay attention to danger of sparks triggered off by unintended contact between the positive (+) terminal of battery and the machine body with a tool, etc.

• Tighten the battery caps.

• Securely tighten the battery terminals.

• Dispose of used batteries by following local disposal regulation.

1-35

1

1. SAFETY PRECAUTIONS

1.8

PROHIBITED MACHINE OPERATION

The following examples of machine abuse and misuse should never be attempted by even the most experienced operator. Such abuse and misuse of this machine and its attachments can result in serious injury, death, severe equipment damage and shortened service life of the machine. Under no circumstance should any of these operations be attempted. Use common sense and follow proper operation procedures found in this OPERATOR'S MANUAL while operating this equipment.

A. DO NOT USE TRACTIVE FORCE OF THE MACHINE FOR LOADING THE BUCKET ATTACHMENT Doing so will exert excessive force on the machine structure, front end attachments and could cause severe equipment damage. Use crawlers for normal travel operations only.

B. DO NOT USE SLEWING FORCE OF THE MACHINE FOR OPERATIONS Doing so will exert excessive force to the machine structure, front end attachments and shorten life of the slewing system of the machine. Also, serious injury or death could result from such operations.

C. DO NOT PERFORM "HAMMERING" OPERATIONS WITH THE BUCKET Performing operations such as hammering and piling will cause extensive damage to the machine and its components. These types of operations can also result in serious injury or death.

1-36

1. SAFETY PRECAUTIONS D. DO NOT OPERATE BUCKET AND ARM CYLINDERS TO STROKE END REPEATEDLY Extending the bucket and arm cylinders to stroke end to clean debris from the bucket, will cause impact to the bucket cylinder causing cylinder damage. Use high pressure water or manually remove stubborn material from the bucket.

A. ALLOWANCES

A

Allowances

1

E. DO NOT OVER EXERT THE MACHINE'S CAPACITIES Know the limitations of the machine and its attachments and operate the machine within those specifications. Do not exceed lift charts. Do not tip or raise the machine to obtain power to move material. This could cause extensive damage to the machine and its components as well as result in serious bodily injury or death.

F.

DEEP EXCAVATION OPERATION

During deep excavation, be careful in order that the belly sides of boom and bucket cylinder hose do not come into contact with ground.

When lowering the boom to the lower limit, be careful in order that the boom does not interfere with crawler shoe.

G. DO NOT USE THIS MACHINE FOR ANYTHING OTHER THAN ITS INTENDED PURPOSE This machine is designed and manufactured for digging, loading and ground leveling operations only. Any other use can exert excessive force to the machine, its components, its systems and result in serious injury or death to the operator and other personnel working in the area of the machine.

1-37

1. SAFETY PRECAUTIONS H. AVOID OBSTACLES WITH DOZER BLADE. Do not strike any obstacles such as large rocks.

The dozer blade may be damaged.

I.

ATTACHMENT TRAVEL POSITION.

When moving the attachment into the travel position, do not hit the dozer blade with the bucket/attachment.

J.

DO NOT SUPPORT MACHINE WITH DOZER BLADE AT ONE END.

When the dozer blade is used as an outrigger, do not support the machine at one end of the dozer blade.

Make sure the support at both ends.

K. DEEP EXCAVATION OPERATION During deep excavation with the dozer blade in front, the boom cylinder could come in contact with the dozer blade.

Place the dozer blade in the back of the machine for deep excavations, unless the working area does not permit it.

1-38

1. SAFETY PRECAUTIONS

1.9

END OF WORK SHIFT SAFETY

Perform all of the following procedures after each shift is complete to insure the machine it in optimal operating condition for the next shift or job site.

1

END OF WORK SHIFT SAFETY 1. Move the machine to a firm, level surface.

2. Lower attachment to the ground.

3. Refill fuel tank to full mark to reduce air volume and condensation (moisture). This will decrease the possibility of freezing in the fuel tank rusting due to moisture and other problems associated with start up and operation.

4. Close and secure all windows in place to prevent water or moisture reaching the electrical components of the machine.

5. Thoroughly clean and inspect the machine. Perform lubrication maintenance and repair or replace any problem areas found before restarting the machine.

6. If performing the machine storage in cold climates, it may be necessary to remove the batteries from the machine and store in a warm well ventilated area. Install the batteries in the machine before next start up. This will help prevent premature battery deterioration.

7. Remove key from key switch and lock all doors and access panels.

1-39

1. SAFETY PRECAUTIONS

1.10

TOWING THE MACHINE

1. If the machine should become stuck in soft soil areas it may be necessary to tow the machine. Attach a wire rope or chain, with the capacity to pull the machine out, to the lower frame.

2. Attach other end to the vehicle used to pull the machine. Operate the machine's travel lever in the proper direction while pulling with the other vehicle.

AVOID INJURY -While towing, do not enter area between the machine and towing vehicle.

-Do not apply a shock load onto the towing rope.

-Do not use eyes on machine lower frame to tow machine.

-Keep the wire rope horizontally, and perpendicular to the crawler frame.

-Tow the machine slowly in low speed mode.

-For the towing of the machine body, provide pads to be applied to the corner of crawler frame to prevent the wire rope and crawler frame from any damages.

Do not pull machine utilizing the brackets welded on the lower plates of the undercarriage. These brackets are provided for pulling lightweight objects. See figure for better reference.

1-40

1. SAFETY PRECAUTIONS

1.11

USE FOPS AND FRONT GUARD

For some jobs (e.g. demolition), a safety structure (e.g. FOPS, Front guard) is needed. When your machine does not have this safety structure, you are not allowed to use your machine for this kind of application.

FOPS : Falling Object Protective Structure

1

1-41

1. SAFETY PRECAUTIONS

1.12

USE SAFETY VALVE AND OVERLOAD ALARM

If your machine is used for lifting application and has a maximum rated lifting capacity bigger than 1 ton or an overturning moment bigger than 40,000 N-m your machine needs safety valves and an overload alarm according to the EN 474 standard.

1.13

ENSURING VISIBILITY

This machine is equipped with mirror and so on to ensure sufficient visibility, but there are areas where are outside the field of vision from the operator. Pay special attention to the invisible area and operate the machine.

When traveling and working in poor visibility area, there is a possibility of injuries and accidents resulting in death because it is hard for operator to see the conditions of obstructions and the work area around the machine. Follow the followings when traveling and working in poor visibility area.

• When right visibility is poor due to attachment, raise the attachment to ensure visibility.

• Clean and adjust mirror at the pre-start inspection to ensure the visibility.

• When rearward visibility monitoring camera (option) is equipped with, clean the lens for clear vision.

• When the visibility can not be ensured sufficiently, provide a flagman in the working areas. Follow the instructions of flagman and pay attention to the signal.

• The signal shall be given by one flagman.

• When working in dark places, turn on the work light. And if required, provide additional lighting facilities to ensure good visibility.

• Stop working when it is impossible to ensure the visual field due to fog, snow or rain.

-Be sure to clean mirror before starting operation to ensure good visibility around machine.

If the visibility around machine is not secured sufficiently, it may cause collisions and accidents resulting in injury and death.

-To avoid the damage or break, do not install the mirror and so on to the handrail of cab entrance. If the mirror and so on is installed to the hand rail, the attaching part of handrail is stressed excessively.

-Do not attach the mirrors except the genuine mirrors (A, B, C and D).

1-42

1500 mm (4'-11")

1. SAFETY PRECAUTIONS

2390 mm (7'-10") B Mirror A

Mirror B

2700 mm (8'-10")

A

(4'-11")

1500 mm

1

C

D

1000 mm (3'-3")

1000 mm

1000 mm (3'-3")

585 mm (1'-9") Mirror D Mirror B,C *The figures of range show reference values only.

1-43

1. SAFETY PRECAUTIONS Mirror A

1 2

E

• • • • • •

Adjust the mirror (A) so that the operator can identify the person who stands on the left rear ends of machine (or post of 1.5m high and 30cm in diameter).

Install the mirror on the small diameter part (E) of the stay shown in the above figure.

Install the mirror so that the mirror (A) does not come in contact with the stay (1) of the mirror.

During adjustment, if the movement of the mirror (A) is not smooth, loosen nut (2) of the mirror and adjust it.

Tightening torque of nut (2) M10: 18.6 to 25.5 N•m (13.7 to 18.8 lbf•ft) Adjust mirror so that the machine side shown in the right figure is reflected in the mirror.

Regarding visible range, refer to previous page.

Mirror B

B 4

3

• • • • • •

Adjust the mirror so that person who stands on the right rear ends of machine (or post of 1.5m high and 30cm in diameter) can be identified from operator.

Install mirror on position shown in the figure.

Install it so that the mirror (B) does not come in contact with the stay (3) of the mirror.

If the movement of mirror (B) on adjusting is not smooth, loosen nut (4) of mirror and adjust it.

Tightening torque of nut (4) M8 : 8.6 to 12.7N•m {6.3 to 9.4lbf•ft} Adjust the mirror so that the machine right side is reflected in the mirror as shown in the figure.

Regarding visible area, refer to the shaded range on previous 1.11.

1-44

1. SAFETY PRECAUTIONS Mirror C

6

5

1

C

Adjust mirror so that person who stands on the right front of machine (or post of 1.5 m height and 30 cm in diameter) can be identified from operator's seat.

• • • •

Install mirror to the position shown in the figure.

Install mirror so that the mirror (C) does not come in contact with the mirror stay (5).

If the movement of mirror (C) on adjusting is not smooth, loosen nut (6) of mirror and adjust it.

Tightening torque of nut (6) M8 : 8.6 to 12.7 N•m {6.3 to 9.4 lbf•ft} Regarding visible area, refer to the shaded range on previous 1.11.

Mirror D

7

D

• • •

•

Install the mirror on the position shown in the above figure.

Install the mirror so that the mirror (D) does not come in contact with the stay (7) of the mirror.

During adjustment, if the movement of the mirror (A) is not smooth, loosen the adjusting screw (2) of the mirror and adjust it.

Tightening torque of adjusting screw (8) M10: 18.6 to 25.5N•m (13.7 to 18.8lbf•ft) Regarding visible range, refer to previous page.

1-45

1. SAFETY PRECAUTIONS

1-46

2. MACHINE FAMILIARIZATION

2. MACHINE FAMILIARIZATION 2

2-1

2. MACHINE FAMILIARIZATION

2-2

2. MACHINE FAMILIARIZATION

2.1

BASIC COMPONENTS OF THE MACHINE

12

11

13

8 7

14 15

30 6

2

5

10 9

4

17

16

3 19

2

20

21 18

1

22 23 24

No.

NAME

31 25

26

28

No.

NAME

27

32

29

No.

NAME

1

ISUZU Engine

12

Arm

23

Lower Roller

2

Hydraulic Pump

13

Bucket Cylinder

24

Upper Roller

3

Engine Muffler

14

Idler Link

25

Track Guide

4

Main Control Valve

15

Bucket Link

26

Slewing Ring

5

Hydraulic Oil Tank

16

Bucket

27

Battery

6

Fuel Tank

17

Operator Cab

28

Travel Motor

7

Swing Motor

18

Dozer cylinder

29

Engine Radiator

8

Swivel Joint

19

Dozer blade

30

Oil Cooler

9

Boom Cylinder

20

Track Shoe Assembly

31

Counterweight

10

Boom

21

Track Idler

32

Engine Air Cleaner

11

Arm Cylinder

22

Track Spring

2-3

2. MACHINE FAMILIARIZATION

2.2

OPERATOR CAB NOMENCLATURE

The operator cab nomenclature, see Figure below, points out locations of operator controls of the hydraulic excavator operator cab. Study these areas and locate these components on the machine. Specific information regarding these components are explained on the following pages of this section.

4

5

6

7

3

9

26 8 11

2

12 10 1

13 14 15

22 21

16 18

17 20

FRONT

DETAIL A 19 A 23

No.

NAME

No.

1

Left Hand Operator Control Lever (Horn Switch)

13

Starter Key Switch

2

Safety Lock Lever (For Hydraulics)

14

Throttle Potentiometer

3

Operating Pedal (Breaker and Nibbler) Option

15

Working Light Switch (Boom, Deck)

4

Left Travel Pedal

16

Tuner

5

Left Travel Lever

17

Air Conditioner Control Panel

6

Right Travel Lever

18

Cap (For Opt. Switch)

7

Right Travel Pedal

19

Life Hammer

8

Hour meter

20

Operator seat

9

Gauge cluster

21

Swing Parking Brake Release Switch

10

Dozer Operating Lever

22

Fuse & Relay Box

11

Cup Holder

23

12 Volt Power Supply

12

Right Hand Operator Control Lever

2-4

NAME

2. MACHINE FAMILIARIZATION

2.3

COMPONENT & CONTROLS NOMENCLATURE

The following information provides a brief description and function of the components and controls of the hydraulic excavator.

All personnel associated with this machine should read and understand this information BEFORE beginning any work with or on this equipment.

2.3.1

GAUGE CLUSTER

The gauge cluster is made up of gauges (fuel level, engine coolant temperature), various switch panels and multi-display.

11

22:00

A. METERS 1: Engine Coolant Temperature Meter 2: Fuel Level Meter

2

S

B. SWITCH PANELS 3: Screen Change Switch 4: BuzzerStopSwitch 5: KPSS Mode Select Switch 6: Washer Switch 7: Wiper Switch 8: Travel Speed Select Switch 9: Auto Accel Switch 10: Select Switch

1

2 3 10

C. LCD MULTI-DISPLAY 11: L.C.D Display

4

9

8

5

7

6

-When caution sign was displayed on the multi-display, stop the work immediately and check and service the section in point.

For checking and servicing, refer to the section for the checking and servicing.

-The display on the multi-display does not entirely assure the condition of machine.

-For the maintenance and inspection of machine, the visual checking should be carried out further without completely depending on the display on the multi-display.

2-5

2. MACHINE FAMILIARIZATION A. METERS 1. COOLANT TEMPERATURE METER

1

This indicates the temperature of the engine coolant water, and operates when the starter key switch is turned to the "ON" position. The temperature is normal in the white range. If the indicator enters the red range, let the engine low idle until the water cools down and the indicator moves back into the white range.

1.RED: Maybe overheated 2.WHITE: Operating condition 3.BLUE: Cold condition, warm up engine and hydraulic oil

2 3 2.

FUEL METER This indicates the amount of fuel. F : Full tank is about 120 L {31.7 gal} This gauge indicates the remaining volume of fuel in the fuel tank. Refuel when the indicator is approaching to the "E" point. Refill the fuel tank with diesel fuel only.

For fuel in use, see "4.3 LUBRICANT, FUEL & COOLANT SPECIFICATIONS".

1. WHITE: Operating zone 2. RED: Refill

1 2 B. SWITCH PANELS

1

10:25

After starting engine, main screen (1) for operator shown in the figure is usually displayed.

S

2

1.

SCREEN CHANGE SWITCH

After turning starter key switch ON or starting engine, the screen is changed in order of "Time for engine oil change" --> "Time for fuel filter replacement" --> "Time for hydraulic oil filter change" --> "Time for hydraulic oil change" --> "Main screen" each time the screen change switch (2) is pressed.

With this menu, the time range to the recommended change time for the filter and oil in use can be identified.

If the screen change switch is not operated for 30 seconds keeping the screen for maintenance displayed, the screen automatically reruns to the main screen.

2-6

2. MACHINE FAMILIARIZATION 2.

BUZZER STOP SWITCH

In case where warning is displayed on the multi-display (LCD), press buzzer stop switch (1) and buzzer shown below stops sounding.

S

The level shown in the table is based on the following contents.

1. This warning shows the condition of personal injury or machine function.

2. This warning shows the change of work mode.

3. This might lead to the failure of machine. Check and service it immediately.

2

Alarmlydsignal Prioritering av gruppe Nivå

LCD-skjerm

Auto stopp

Manuell stopp

1

Data fra mechatro-kontrollene er ikke mottatt.

—

O

3

O

O

1

Trykket for lastebommens sylinder overskrider den satte verdien,

—

O

3

—

O

1

Bryteren for håndbrekket er satt til ON (PÅ).

O (5 sec.)

O

2

O

O

1

Motoren er stoppet etter motoroljetrykket er lavt.

O (5 sec.)

—

1

O

—

—

O

2

—

O

A

Lavt motoroljetrykk, frakobling.

3

B

Maskinforhold

Kun Motore Type startnøkk- går el ON (PÅ)

3

Motorens kjølevæske har en høyere temperatur enn 105°C.

—

O

3

O

O

3

Luftfilteret er tilstoppet.

—

O

3

O

O

Selvdiagnose (sensor, ventil osv.).

—

O

3

O

O

10:25

3

B013

H

Alarmlydsignal

Type1:kontinuerlig, Type2:Beep ON 0.2sec, OFF 0.3sec., Type3:Beep ON 0.5sec, OFF 0.5sec.

2-7

2. MACHINE FAMILIARIZATION 3.

WORK MODE SELECT SWITCH

When engine starts, it is set to "S" mode. Select proper work mode from 2 modes shown below according to the work condition and the purpose. The work mode is switched in order of "S" --> "H" each time the work mode select switch is pressed. The selected work mode is displayed on the left lower corner of multi-display for confirmation.

10:25 S

S : S mode (for standard work and loading operations) H : H mode (for heavy duty work)

3

The mode after the engine starting is always the start from "H" mode. Before beginning the work, make sure the mode that had been selected is correct.

For the reference of each "3.1.11 SELECTION OF WORK MODE AND SWITCHING OF THE ATTACHMENT MODE", see Chapter 3.

4.

WASHER SWITCH

Press washer switch and washer fluid is sprayed through the nozzle of front window while the switch is being pressed. The washer tank is located on the rear side of cab.

10:25 S

4

Make certain the washer reservoir has washer fluid before operating washer.

2-8

5

2. MACHINE FAMILIARIZATION 5. WIPER SWITCH When the wiper switch is operated, the indication of "Intermittent " or "Continuous " appears on the lower part of multi-display. a. Press it once : Wiper moves intermittently b. Press it again : Wiper moves continuously c. Press it once more : Wiper stops moving 6.

TRAVEL SPEED SELECT SWITCH

Slow speed traveling is necessary to load and unload the machine on to a trailer. During loading or unloading, do not change the travel speed.

The travel speed select switch is located on the gauge cluster switch panel. Each time engine is started, travel speed is automatically set to LOW 1st (turtle) speed. Press the travel speed (rabbit) switch on the gauge cluster, and the speed is changed to the HIGH 2nd and the (rabbit) is indicated on the multidisplay.

10:25 S

LOW (1st) speed : turtle Set to LOW when moving the machine on a rough or soft road, slope, or in a narrow place, or when powerful tractive force is required.

HIGH (2nd) speed : rabbit Set to HIGH when moving the machine on flat, hard ground.

7.

6

AUTO ACCEL SWITCH

When loading or unloading machine on trailer, turn the auto accel switch off.

If it is operated keeping the accel switch on, the engine speed changes suddenly.

Do not operate the machine in "Auto acceleration switch ON" to avoid abrupt speed change of engine. Abrupt speed change causes the machine fall from the deck of trailer.

10:25 S

7

On the condition that "Auto acceleration switch (7) is turned ON" and "Throttle dial is set to 1200 rpm or more", when the control lever and / or pedal are not operated for 4 seconds or more, the engine speed changes to 1200 rpm automatically.

When the control lever and / or pedal are operated, the engine speed returns to the throttle dial set level.

When the acceleration switch is turned off, the auto acceleration function does not work. As a result, the engine speed does not change.

While the auto acceleration is working, this switch is turned off, and the engine speed rises to the auto acceleration set speed.

2-9

2

2. MACHINE FAMILIARIZATION 8. SELECT SWITCH This switch is usually set to "OFF", but this switch (8) is available for clock setting, contrast adjustment.

For the how to use select switch, see the following "8.1 Clock Adjustment Switches" to " 8.2 Contrast Adjustment Switches".

Press screen change switch (1) during the above adjustment and setting operations and the screen returns to the previous screen.

8.1 Clock Adjustment Switches

1

8

2

7

3

4

6

1: Screen Change Switch 2: Buzzer Stop Switch 3: Work Mode Select Switch 4: Washer Switch 5: Wiper Switch 6: Travel Speed Select Switch 7: Auto Accel Switch 8: Select Switch

5

1. Turn starter key switch on and display main screen (a) for operator, and then press select switch (8) and display "SWITCH STATUS CLOCK/CONTRAST" select screen (b).

2. In operations of FEED (4) and FEED (5), move cursor to "CLOCK/CONTRAST" screen (c) and then press select switch (8) and the "ADJUST CLOCK ADJUST CONTRAST" screen (d) is displayed.

3. In operations of FEED (4) and FEED (5), move cursor to "ADJUST CLOCK" and then press select switch (8) and the "ADJUST CLOCK" screen (e) is displayed.

4. Select any of "YoMoDoHoM" in operation of FEED (4) and FEED (5) and vary the values in operations of FEED (4) and FEED (5).

5. After adjustment, press select switch (8) and the adjusted values are stored as memory and time setting is completed, and then the screen returns to main screen (a).

2-10

2. MACHINE FAMILIARIZATION 8.2 Contrast Adjustment Switches

1

8

2

7

3

4

6

1: Screen Change Switch 2: Buzzer Stop Switch 3: Work Mode Select Switch 4: Washer Switch 5: Wiper Switch 6: Travel Speed Select Switch 7: Auto Accel Switch 8: Select Switch

5

2

1. Turn starter key switch on and display main screen (a), and press select switch (8) and display "SWITCH STATUS CLOCK CONTRAST" select screen (b).

2. In operations of FEED (4) and FEED (5), move cursor to "SWITCH STATUS CLOCK CONTRAST" screen (c) and then press select switch (8) and the "ADJUST CLOCK ADJUST CONTRAST" screen (d) is displayed.

3. In operations of FEED (4) and FEED (5), move cursor to "ADJUST CLOCK ADJUST CONTRAST" and then press select switch (8) and the "ADJUST CLOCK ADJUST CONTRAST" screen (e) is displayed.

4. Press select switch (8) and the "ADJUST CONTRAST 55555" screen (f) is displayed.

5. Vary the values by pressing the desired figure in operations of FEED (4) and FEED (5).

The available setting range is in 9 steps from "11111" to "99999".

[Example] 11111 (faint) --> 99999 (clear) * The initial set value is 55555.

6. Press select switch (8) and the adjusted values are stored as a memory and the contrast adjustment is completed, and then the screen returns to main screen (a).

2-11

2. MACHINE FAMILIARIZATION C. LCD MULTI-DISPLAY

When the warning is displayed on the multi-display, stop the work immediately and check failure cause and service the trouble.

For checking and service, refer to the section of "Maintenance".

The gauge cluster processes signals received from various sensors and switches and outputs the signals to LCD display and lamp display, and makes the buzzer sound.

The everyday check should be carried out according to not only the display on the multi-display but also the instructions in section "Maintenance".

LCD display function is roughly divided into the following 4 types.

LCD (Liquid Crystal Display)

S

1.Main Screen Display for Operator 2.Display in Accordance with Switch Operation 3.Warning Display 4.Display for Maintenance

C.1 MAIN SCREEN

After starting engine, usually clock is displayed.

2-12

2. MACHINE FAMILIARIZATION C.2 DISPLAY BY SWITCH OPERATION When using it by selecting switch on the switch panel provided on the gauge cluster, the selected mode is displayed on the lower part of multi-display.

22:00

1 1

S

2 3 4 5

3

1

2

2

3

4

5

Arbeidsmodus vises (S, H) Kjørehastighet vises ( , ) Skjermbilde for automatisk aksel Skjermbilde for vindusvasking (periodisk/kontinuerlig) Visning av feil

4

1. Work mode display The mode changes in order of "S" --> "H" each time the work mode switch (1) is pressed and the selected mode is displayed on the lower corner of multi-display.

2. Travel low speed and high speed display The display is changed in icons "turtle" --> "rabbit" --> "turtle" in order each time the travel low and high speed change switch is pressed and the selected mode is displayed.

3. Auto accel display Press auto accel switch (3) and the icon "Auto Accel" is displayed to inform that auto accel is functioning.

4. Wiper display screen Press wiper switch (4) and the icon "intermittent" is displayed when the wiper motor is running for front window intermittent wiping, and icon "continuous" is displayed when the motor is running for continuous wiping.

5. Screen displayed when trouble occurred For details, contact dealer/distributor.

2-13

2

2. MACHINE FAMILIARIZATION C.3 DISPLAY FOR MAINTENANCE This screen displays the remaining time to the end of recommended replacement interval specified for filter/oil.

After reaching to the end of replacement interval, check and serve them following to section "Maintenance".

The recommended replacement interval is the accumulated time which is counted by controller when the engine is running.

This menu is available for confirmation of the following items.

The maintenance screen changes each time the screen change switch is pressed.

Replacement Interval ITEM

DEFAULT

Engine Oil

500 Hr

Fuel Filter

500 Hr

Hydraulic Filter

1,000 Hr

Hydraulic Oil

5,000 Hr

492Hr ENG OIL

S

1.

Remaining time display to the engine oil change This display shows the remaining time to the coming engine oil change.

2.

Remaining time display to the coming fuel filter replacement This display shows the remaining time to the coming engine fuel filter replacement.

992Hr S

4993Hr S

3.

Remaining time display to the coming hydraulic oil filter replacement This display shows the remaining time to the coming hydraulic oil filter replacement.

4.

Remaining time display to the coming hydraulic oil change This display shows the remaining time to the coming hydraulic oil change.

-The display automatically changes to the main screen, if switch is not operated for 30 seconds.

-For the setting procedure of maintenance time to be performed to the coming oil change in each type and filter replacement, see "2.3.1.C.4 SET PROCEDURE OF MAINTENANCE SCHEDULE".

2-14

2. MACHINE FAMILIARIZATION C.4 SET PROCEDURE OF MAINTENANCE SCHEDULE This machine is equipped with multi-display which makes confirmation of remaining time to the coming replacement/ change time of engine oil, fuel filter, hydraulic oil filter and hydraulic oil. When the remaining time reaches to Zero (0), replace or change them and perform the initial setting in the following order.

Interval of replacement of parts is mentioned below.

Engine oil : 500 Hr Fuel filter : 500 Hr Hydraulic filter : 1,000 Hr Hydraulic oil : 5,000 Hr

Prosedyre 1

2

3

4

5

Driftsprosedyre

2

Visnings-Funksjon

Skjerm

NEW HOLLAND KOBELCO

Drei startnøkkelbryteren til på

Trykk på " " én gang for å vise endringsbryteren på bryterpanelet.

Klokkevisningen endres til visning av gjenværende tid før kommende motoroljeskifte.

10:25 S

250 Hr

Trykk på bryteren " " én gang visningen for motoroljeskifte reverseres.

MOTOROLJE

S

Det kan være nødvendig å justere intervallet for kommende skifte til 10 timer. Trykk i så tilfelle på bryteren " "og tiden for det kommende motoroljeskiftet vil bli lagt til.

Trykk på bryteren " " og tiden før det kommende motoroljeskiftet vil reduseres.

Trykk på alarmstoppbryteren " " én gang når du ønsker å gå tilbake til standardinnstilingen.

Trykk på velgerbryteren " " én gang og tiden lagres.

250 Hr MOTOROLJE

500 Hr MOTOROLJE

Etter noen sekunder endres automatisk skjermbildet til klokke.

Trykk på skjermbyttebryteren én gang til.

Trykk på skjermendringsbryteren én gang til.

Utskiftingsintervallet endres med hvert trykk på bryteren

Trykk på velgerbryteren for å angi det ønskede intervallet

10:25 S

250 Hr MOTOROLJE

S

250 Hr MOTOROLJE

500 Hr ENGINE OIL

500 Hr ENGINE OIL

S

1.

After displaying the display for setting by pressing the display change switch, set the respective maintenance time for fuel filter, hydraulic oil filter and hydraulic oil while repeating the procedure 2 to 5.

2.

The engine oil change time is displayed on the multi-display by 500 hours as a warning, but the buzzer does not sound.

2-15

2. MACHINE FAMILIARIZATION C.5 WARNING DISPLAY The warning is displayed in order of priority, and when many troubles occurred at the same time, for levels 1 and 2 in order of priority (A) level 1 is displayed in priority to level 2.

When these warning are displayed, there is a possibility of serious trouble. Therefore stop the operation immediately, investigate the causes and take a proper measure.

1.

WARNING CLASSIFICATION (PRIORITY A)

Skjermbilder

CPU

2.

Level

Innholdet i advarsel

1

Vises når mechatro-kontrollen ikke sender data

1

Trykket for lastebommens sylinder overskrider den satte verdien.

1

Vises når svingparkeringsbremsen er deaktivert.

1

Vises når nødstoppen aktiveres på grunn av lavt motoroljetrykk

Løsning

Kontakt vår distributør/forhandler for kontroll og service.

WARNING CLASSIFICATION (PRIORITY B)

Skjermbilder

Nivå

Innholdet i advarsel • Vises når kraftsparingskontrollen brukes, fordi oljetrykket er senket til det angitte trykket eller lavere.

2

Løsning • Stopp umiddelbart motoren og kontroller om oljenivået er for lavt, samt den frakoblede kabelen. Hvis oljenivået er lavt, må det fylles på motorolje i henhold til “TEKNISK DATA FOR SMØREMIDDEL, DRIVSTOFF OG KJØLEVÆSKER” på side 4-11, eller oljen må skiftes.

• Når denne advarselen vises fordi motoren ikke roterer, kan det ha oppstått problemer på grunn av frakobling av kabler osv. Kontakt distributør/forhandler for reparasjon.

Stopp motoren, senk kjølevæsketemperaturen til lav tomgangshastighet og la motoren kjøles ned.

Vises når kjølevæsketemperaturen har Hvis denne advarselen ikke blir borte etter flere nådd den fastsatte temperaturen, eller minutter, må motoren stanses og høyere kjølevæskenivået kontrolleres. Kontroller også om vifteremmen er for løs og om radiatoren er tilstoppet.

• Vises når kablene er frakoblet.

3

10:25 B013

H

3

Vises når motoreffekten er senket fordi Kontroller filteret og rengjør det. Hvis nødvendig luftfilterinntaket er tilstoppet. må det skiftes ut.

3

Denne feilmeldingen vises når det oppstår problemer med trykksenssor, utjevningsventil osv.

2-16

Kontakt distributør/forhandler for reparasjon.

2. MACHINE FAMILIARIZATION Skjermbilder

Nivå

Innholdet i advarsel

Løsning

Batterifeil.

(Høy spenning/lav spenning/dårlig lading) 4

Hvis advarselen ikke blir borte etter at Kontroller det elektriske utstyret som brukes motoren er startet opp og har gått en og kontroller ladekretsen stund, kan dette skyldes dårlig batterilading.

Drivstoffnivået er under det angitte nivået.

5

Tiden som gjenstår før angitt motoroljeskifte er null (0).

Fyll på drivstoff.

Fyll på angitt mengde med ny motorolje.

2

2-17

2. MACHINE FAMILIARIZATION 2.3.2

LOCATION OF SWITCHES AND METERS 26 10

9

1 2 3 11 4 5 7 6

8

A

FRONT

No.

NAME

No.

DETAIL A

NAME

1

Starter Key Switch

7

Cap (For Opt. Switch)

2

Throttle Potentiometer

8

12 Volt Power Supply

3

Working Light Switch (Boom, Deck)

9

Horn Switch

4

Over Load Alarm Select Switch

10

Hour Meter

5

Tuner

11

Swing Parking Brake Release Switch

6

Air Conditioner Control Panel

2-18

2. MACHINE FAMILIARIZATION 1. Starter Key Switch The starter key switch is located on the right hand operator console and has 4 operating functions.

•

•

•

•

OFF : When starter key switch (1) is turned to this position, the engine stops and electrical power to the machine's electrical systems is stopped after approximately 3 seconds.

ACC : With starter key switch (1) in the "ACC" position only the cigarette lighter, tuner and horn will have power.

ON : 1 2 When starter key switch (1) is in the ON position, electrical power is supplied to all the machine's electrical systems.

START : When starter key switch (1) is turned to this position electrical power is supplied to the starter solenoid causing the starter to start the engine. After engine starts key should be released to go back to the "ON" position.

2. Throttle Potentiometer The throttle potentiometer (2) is located on the right hand operator console and controls engine RPM. When the throttle potentiometer is rotated to any position it increases or decreases engine rpm and maintains engine at the programed RPM for that particular position on the dial.

• •

3.

LO (Low idling) : The engine speed reduces to the minimum at the position turned to the leftmost.

HI (High idling) : The engine speed rises to the maximum at the position turned to the rightmost.

Working Light Switch (Boom, Deck)

Press the switch and the work lights on the boom (left) and deck (right) go on.

Press the side without symbol mark and the work lights on the boom (left) and deck (right) go off.

ON

4. Over Load Alarm Select Switch The over load alarm select switch is located on the right hand control console. The over load alarm switch is a 2 position rocker switch which is used for lifting operations.

•

•

ON : Push the symbol side of switch down to turn over load alarm "ON" when performing lifting operations.

OFF : Push back of switch down to turn over load alarm "OFF" when performing other operations.

5. Radio (Tuner) For the control of radio, see Page "2.3.7 HANDLING OF RADIO".

6. Air Conditioner Control Panel For air conditioner control, see "2.3.8 AIR CONDITIONER".

2-19

2

2. MACHINE FAMILIARIZATION 7. Caps These are used to install switches in option.

8.

12 Volt Power Supply

The 12 volt power supply (1) is located beside the rear side cover.

Four use of common auto accessories such as a fun or other accessories requiring 12 volt (DC) power. Pull cover away from 12 volt power supply and insert 12 volt male socket into power supply. Replace cover after use.

MAXIMUM CONTINUOUS OUTPUT - 180 Watt

1

Do not use the cigarette lighter as a power supply source for 12 volt accessories. It is a 24 volt outlet. Pulugging a 12 volt accessory into a 24 volt connector may result is shorting and/or fire.

9.

Horn Switch

Always sound horn before starting engine to alert personnel that the machine is going to be operated.

The horn switch is a momentary push grey button located on the operator's left control lever.

10. Hour Meter This indicates the total time the engine has run. Even if the excavator is not moving, the meter continues to count as long as the engine is running.

2-20

2. MACHINE FAMILIARIZATION 11. Swing Parking Brake Release Switch

Swing parking brake is usually locked. The swing parking brake is released in swing and arm-in operation. When it cannot be unlocked due to trouble, turn toggle switch to "RELEASE LOCK" (unlock), and the parking brake is released. Then, move machine to safe area immediately and contact our shop.

And return to toggle switch to "NORMAL" position in normal condition.

2

FRONT

2-21

2. MACHINE FAMILIARIZATION 2.3.3 1.

2.

3.

4.

5.

LEVERS AND PEDALS 3

Safety Lock Lever Control lever (ISO Control Pattern) Travel lever Operating pedal (Breaker and Nibbler) Option Dozer Operating Lever

4

1

2 5

2

1. Safety Lock Lever The safety lock lever is provided to prevent any unexpected operation due to the unexpected movement of control levers.

-Do not stand up and move during operation or there is a possibility of suddenly being moved by unexpectedly touching and shifting the control lever.

-Raise the safety lock lever to the "lock position" securely.

Make sure that the safety lock lever is held to the locked position shown in the figure.

-When unlocking, do not touch other levers unintentionally. If touches other lever unintentionally, this may cause the danger due to malfunction of machine.

-After completion of work or during transportation, hold the safety lock lever to the "locked position".

Locking Hydraulic System (A)

A

B LOCKED (UP) POSITION When the safety lock lever is set in the "LOCKED (UP) Position" the hydraulic system is shut down.

2-22

2. MACHINE FAMILIARIZATION Unlocking Hydraulic System (B)

A

B

UNLOCKED (DOWN) POSITION

2

When the safety lever is set to the "UNLOCKED (DOWN) Position" all hydraulic functions are active.

2. Control Levers (ISO Operating Pattern) These two levers activate each operation as illustrated in the right.

-Confirm for safety around the working area. Also ensure that each lever operation is in accordance with the operating pattern indicated on the labels.

-If labels do not match the operator's control pattern, replace them immediately to avoid accidents and/or injury.

-When the contents of label do not accord with the machine movement, replace the label with proper label suited for the machine.

Release the hand and the lever returns to the neutral position, and then the attachment stops moving. And it is possible to perform various operations at the same time.

•

•

Left Control Lever (1) Swing Right (2) Swing Left (3) Arm Out (4) Arm In N (Neutral): Upper structure and arm are held in the position where those are.

Right Control Lever (5) Boom Down (6) Boom UP (7) Bucket Digging (8) Bucket Dumping N (Neutral): Boom and bucket are held in the position where those are.

(3) (2)

(1)

(7)

(4)

(8) (6)

(6) (3)

(1) (2)

(4) (5)

(8)

2-23

(5)

(7)

2. MACHINE FAMILIARIZATION 3. Left and Right Travel Lever & Pedal The travel lever & pedal are located in front of operator seat. They are used to move the left or right track of the machine either forward or backward.

-Take precaution with the control lever in travel operation. There is a possibility of accident because the attachment is suddenly swung and moved by the unexpectedly touching and shifting the control lever.

-When operating the control lever, make sure the crawler frame direction. When the travel motor is located on the front side, the travel lever functions of the travel levers will be opposite.

-Do not perform the work while putting foot on the pedal. There is a possibility of serious accident resulting in injury and death because the machine starts abruptly by unexpectedly depressing the pedal.

Do not put foot on the pedal but of driving with foot on the pedal and changing the direction.

-Pay attention when driving and operating with pedal.

• • •

(a)

(a) "Forward" Variable speed forward track movement. (b) "Backward" Variable speed reverse track movement.

(N) "Center" Neutral position.

(N) (a) (b) (N) (b) (a)

(a)

(b)

(b)

(a)

(b)

2-24

2. MACHINE FAMILIARIZATION 4. Dozer operation Lever OUTLINE Blade is attached on lower frame with pin, and is used for backfilling and leveling after digging works by operating dozer cylinder through the aid of dozer control lever in cab and moving blade up and down.

BEFORE OPERATING THE DOZER BLADE

Read, understand and follow all safety precautions and operation procedures found in this manual before operating the machine or any attachment.

The dozer blade operating lever (1) is located on the right side of the right hand operator console basic function is to lift or lower the dozer blade.

1. Start machine and place the safety lock lever in the "UNLOCKED" (Down) position.

2. Move throttle potentiometer to the "Hi" idle position."

3. Using boom, arm and bucket controls set the attachment to desired position.

4. Pull (A) the dozer blade operating lever to lift up the blade.

5. Push (B) the blade operating lever forward to lower the dozer blade.

2 B

1

A

A

B

Dozer blade control function is live at all times. That is, even with the safety lock lever in locked up position.

2-25

2. MACHINE FAMILIARIZATION 2.3.4

FUSES & RELAY BOX

Make sure the starter key switch is in the "OFF" position when replacing fuses.

The fuses protect the electrical system from excess current. If operation is not normal, a fuse may be blown.

Replace blown or faulty fuses with the spare fuses as follows.

Replace any fuse generating white powder on it or in case that some looseness exists between the fuse and fuse holder.

-When replacing a fuse, replace it with one of the same capacity.

-The spare fuses are stored in the back side of fuse box cover.

Replacing Procedure 2

1. Loosen four machine screws (2) used to install cover (1) located on the rear side of operator seat, and remove cover (1).

2. To remove the cover of fuse box, press lock (4) of cover (3) inward to unlock and then lift it up.

3. When replacing the fuse, remove the fuse from the fuse box with fuse remover.

4. After replacement of fuse, attach the cover securely.

1

3

FRONT

2-26

4

2. MACHINE FAMILIARIZATION Fuses

1

2

3

4

5

6

7

8

9

10 11 12 13 14 15 16

33 34

35 36

2 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32

No.

AMPS

1

20A

2

FUNCTION

No.

AMPS

Cab Work Light

21

10A

DC-DC Converter

20A

Cab Work Light

22

5A

Option (8)

3

5A

Gauge Cluster

23

15A

Roof Wiper

4

20A

Wiper, Washer

24

20A

Flasher, Alarm

5

20A

Option 1

25

10A

Safety Lever Lock

6

20A

Option 3

26

5A

Mechatro Controller

7

15A

Air Conditioner

27

20A

Mechatro Controller

8

5A

Air Conditioner

28

20A

EGR Rly Glow Timer

9

5A

Option (Hand Control)

29

10A

Alternator Fuel Pump

10

5A

Relay, Hour Meter

30

5A

Gauge Cluster (Back Up)

11

10A

Cigarette Lighter

31

20A

Fuel Supply Pump

12

10A

Horn, Horn Relay

32

5A

Mechatro Controller (Back Up)

13

10A

Tuner

33

5A

Spare

14

20A

Starter Key Switch

34

10A

Spare

15

5A

Room Lamp, Tuner

35

15A

Spare

16

10A

Option 2

36

20A

Spare

17

10A

Option 4

18

10A

Solenoid Valve

19

5A

Air Conditioner

20

20A

Work Light

2-27

FUNCTION

2. MACHINE FAMILIARIZATION 2.3.5

FUSIBLE LINK (FOR STARTER)

In case power does not come when the starter key switch is turned "ON", a disconnection of the fusible link is suspected.

Inspect and replace the fusible link.

The fusible link is of a fuse wiring of big size provided in the electric wiring

Checking and replacing procedure 1. Using starter key switch, unlock and open the side door (1) on left side of counterweight, and hold the door open with stay.

2. Loosen four bolts (3) used to install cover (2), and remove cover (2).

3. Remove fusible link (4) and check or replace it with new one.

4. After replacement of fusible link (4), install cover (2) with bolts (3).

5. After checking or replacement, remove stay and close the door and lock it securely.

1 3

3

4

2-28

3

2

2. MACHINE FAMILIARIZATION 2.3.6

MECHATRO-CONTROLLER (CPU), ENGINE CONTROLLER (EGR) 1

2

FRONT

Mechatro-controller and engine controller are positioned at the rear side of operator seat.

1. Mechatro Controller (CPU) 2. EGR Cut Controller

-Be careful not to splash water, mud and drinks on the controllers.

-When error occurred on the controller, do not take self-service, but contact our dealer/distributor.

2-29

2

2. MACHINE FAMILIARIZATION 2.3.7

HANDLING OF RADIO

A. EXPLANATION OF UNITS

2

6

5

8

1.

1.

2.

3.

4.

5.

6.

7.

8.

2.

3

4

7

1

Name and How to Use of Each Unit Power switch AM/FM switch key Volume control UP / DOWN key Preset key DISP (display change) key Sound control key Display (Time/frequency) Power control

1. Press the power switch (1) and the power is switched from OFF to ON. After displaying the band AM or FM, the frequency or the time is displayed.

1

2-30

2. MACHINE FAMILIARIZATION 3.

Display switching

1. To change the display from/to the frequency display to/ from the time display, press "DISP" key (6).

When the time display is changed to the frequency display, firstly the band display appears and then the frequency display appears.

6

2

4.

Band switching

1. When pressing "AM/FM" key (2) each time, the band display is switched to FM1FM2AM in order.

When the band is switched, the station received before switching is selected.

5. How to select station This radio can select the station by the following three methods.

-Manual tuning -Auto select station -Preset memory Each selecting method is explained below.

2-31

2

2. MACHINE FAMILIARIZATION 5.1 Manual tuning 1. When pressing "UP" or "DOWN" key, the frequency increases or decreases by one step.

1 step: AM 9kHz 1 step: PM 0.1MHz

5.2 Auto select station 1. When pressing "UP" or "DOWN" key (Press more than 1 second), the frequency increases or decreases by one step.

2. When the radio waves are received during auto tuning, or when pressing "UP" or "DOWN" key, the auto tuning is interrupted, but the frequency is keeping as it is.

5.3 Preset memory 5.3.1 Auto preset The good received frequencies are detected, and they can be memorized in 6 memories of preset automatically.

1. Press the tone control key (7) for 1 second or more.

The desired station starts the presetting.

2. During presetting, the display "A" moves from left to right.

3. After auto presetting, this function can receive the memorized station.

5

7

2-32

2. MACHINE FAMILIARIZATION 5.3.2 Manual preset Press one of the 6 "PRESET" keys (5) for 1 second or more. The currently received station is memorized in the pushed button of preset No. 1. Press one of the 6 "PRESET" keys (5) for 1 second or more.

2. After 3 flickering of the memorized preset No. display, the frequency is displayed.

5

7

2

5.3.3 Preset memory Press one of the 6 "PRESET" keys (5) for 0.5 second or less. And the calling frequency which is memorized in the preset No. and its reception are available by pressing the "PRESET" key.

1. Press one of the 6 "PRESET" keys (5) for 0.5 second or less.

2. After the pressed preset No. is displayed, the display is changed to the frequency which is memorized in the preset No. 3. Receive the required radio station by changed frequency.

2-33

2. MACHINE FAMILIARIZATION 6.

Volume control

1. To turn up the volume level by 1, press the "+" side of volume control key (3). And to turn down the volume level by 1, press the "-" side of volume control key (3).

During the operation of volume control key, the level of volume is displayed.

2. Hold the volume control key in the pressed condition, the volume level changes continuously up and down.

3. After operation of the volume control key, the display returns to the frequency or the time display.

7.

3

Sound control

The "Balance" and "Tone" are adjustable with this key.

-Balance adjustment: "BAL" To control the volume of right and left speakers.

-Treble adjustment: "TRE" To control the treble.

-Bass adjustment: "BAS" To control the bass.

4

2-34

7

2. MACHINE FAMILIARIZATION 7.1 Selection of adjusting item 1. The display changes to "BAL", "TRE", and "BAS" in order whenever "SOUND" control key is pushed.

Choose the item that you desire to adjust.

2

7.2 Balance control 1. To raise the volume of a left speaker, push the "UP" key (4) while "BAL" is displayed.

To raise the volume of a right speaker, push the "DOWN" (4) key while "BAL" is displayed.

7.3 Treble control 1. To emphasize the treble, push the "UP" key (4) while "TRE" is displayed.

To weaken the treble, push the "DOWN" key (4) while "TRE" is displayed.

2-35

2. MACHINE FAMILIARIZATION 7.4 Bass control 1. To emphasize the bass, push the "UP" key (4) while "BAS" is displayed.

To weaken the bass, push the "DOWN" key (4) while "BAS" is displayed.

7.5 Time setting 1. Press "DISP" key (6) for 1 second or more while the time is displaying. The "Hour" display flickers.

2. To increase "Hour", press the "UP" key (4).

To decrease "Hour", press the "DOWN" key (4).

3. Press "DISP" key (6) again, and the "Minute" display flickers.

4. To decrease "Minute", press the "UP" key (4).

5. Press "DISP" key (6) again, and the time setting is completed.

B. ANTENNA To prevent interference, retract the antenna in before transportation and storing.

2-36

6

4

2. MACHINE FAMILIARIZATION 2.3.8

AIR CONDITIONER

The air conditioner provides the comfortable indoor atmosphere and freely controls the room temperature and also removes the moisture resulting in prevention of blur on the glasses.

The air conditioner is located under the operator seat and sends out warm air and cool air in the cab.

Grille (Air outlet) Select air stream in preferable direction by hand.

(A), (B), (C), (D): Air outlet (E): Solar radiation sensor

(A) (A) (E)

2

(C)

(B) (D)

Precaution in Use of Air Conditioner

-When the air conditioner is running-in, start the engine at slow speed. Do not start the air conditioner at high speed. This might cause failure of air conditioner.

-Pay attention to the control panel and solar radiation sensor (E) so as not to splash water on them. The entry of water in the control panel and solar radiation sensor might cause unexpected failure. And do not bring fire near the air conditioner.

-Keep the solar radiation sensor clean to have the auto function of air conditioner achieved sufficiently. And do not place the things which may interrupt the function of sensor on the surroundings.

2-37

2. MACHINE FAMILIARIZATION Control Panel Description 8

2

9

No.

5

3

7

NAME

1

Auto Control Switch

2

Fresh and Recirculate Air Selector Switch

3

Compressor Switch

4 5

4

No.

1

6

NAME

6

Power Switch

7

Temperature Setting Switch (C degrees <-- --> F degrees Selector Switch)

Fan Speed Selector Switch

8

Air Outlet Mode Selector Switch

LCD Display

9

Defroster Switch

-The LCD display indicates temperature, air outlet mode, compressor ON - OFF, AUTO, recirculate and fresh air and fan speed.

-Each switch, FAN mark of blower, and TEMP mark are illuminated green at night.

A. FUNDAMENTAL USE Before turning air-condition on, close doors of cab and windows to achieve the best performance.

1. Press control switch "AUTO" (1) to control air capacity and blower outlet automatically, and set the 2 3 1 temperature in the range from 18.5C degrees (65.3F degrees) to 31.5C degrees (88.7F degrees).

The outlet temperature, outlet opening and fan speed are adjusted automatically so that indoor temperature of cab comes closer to the set temperature.

2. Select proper mode manually through recirculate and 4 fresh air capacity selector switch (2) and compressor switch (3) ON - OFF. 3. Select preferable fan speed manually through fan speed selector switch (4) when fan speed, selected through auto control, is not preferable.

The indicator lamp of "AUTO" in LCD display goes out. Press "AUTO" switch to retune to automatic climate control.

2-38

2. MACHINE FAMILIARIZATION B. CONTROL PANEL FUNCTIONS 1. Main Power Switch and Display a. LCD display is illuminated (5) when the climate controlAC is operating.

When the climate control-AC is stopped, LCD will be tuned off. b. Press main power switch (6), and all functions for the climate control-AC switch ON or OFF. Each time when this switch is pressed, the function switches ON and OFF. When switched ON, the climate control-AC starts operating at the point set before switching OFF (when it is set to "AUTO", in auto mode; if NORMAL is selected, then in normal mode).

5

6

2

The key switch will switch air-conditioner OFF, but the operating condition just before switching off may not be restored when the key switch is turned ON again.

2. Auto Control Switch and Display a. Press the main power switch (6) to activate the climate control-AC and the LCD display (5) will illuminate. b. Press control switch AUTO (1), and fan speed and air outlet are automatically controlled, and "AUTO" indicator lamp on LCD display is illuminated. c. When the main power switch (6) is OFF, the system will retain the previous setting in memory.

Therefor, when the main power switch is pressed again, the climate control AC will come on in the auto control mode. In the auto mode, the fan speed and air outlet openings are operated automatically

2-39

1

5

6

2. MACHINE FAMILIARIZATION 3. Temperature Setting Switch and Display a. The set temperature is indicated in digits on LCD display (5). Temperatuer set range is 18.5C degrees 5 (65.3F degrees) to 31.5C degrees (88.7F degrees). b. Press the two temperature set switches (7) simultaneously for 5 seconds to change the display from Centigrade (C degrees) to Fahrenheit (F degrees) or viceversa in the LCD display.

(Eg.) 25C degrees --> 77F degrees or 77F degrees --> 7 25C degrees c. Press temperature set switch DOWN or UP to change the set temperature.

The temperature goes up or down by 0.5C degrees (0.9F degrees) in graduation.

The set temperature may be raised or lowered by continued pressing of the switch. d. The set temperature 18.5C degrees (65.3F degrees) is the lowest cooling temperature, and 31.5C degrees (88.7F degrees) is the highest heating temperature.

Control beyond either of these limits is not possible.

4. Air Outlet Mode Selector Switch and Display (1) Air outlet position is indicated by the arrow on LCD display.

(2) Press air outlet mode switch (8) in the condition where auto display light is on, and the display mode is fixed, "AUTO" indicator lamp on LCD display goes out, and "AUTO" control of air outlet opening is released.

Press it again, and the level is changed to VENT --> BILEVEL --> FOOT --> FACE

2-40

8

2. MACHINE FAMILIARIZATION 5. Defroster Switch and Display a. Press defroster switch (9), defroster indicator lamp will be displayed (5). b. Press air outlet mode selector switch (8), and it returns to air outlet mode just before pressing defroster switch. c. Press defroster switch (9) in the condition where AUTO display is lighting up, "AUTO" indicator lamp on LCD display (5) goes out and the auto control of air outlet opening is released.

8

2

9

5

4

6. Recirculate and Fresh Air Selector Switch and Display a. Suction (fresh air intake) mode is indicated on LCD display (5). b. Each time recirculate and fresh air capacity selector switch (2) is pressed, the mode is switched to air recirculate or fresh air intake.

A: Air Recirculation B: Fresh Air Intake

7. Compressor Switch and Display Press compressor switch (3) in the condition where mark on LCD display is unlit, compressor starts operating and indicator lamp of mark on LCD display (5) goes on.

Press it again, and compressor turns off, and indicator lamp of mark on LCD display (5) goes out.

8. Fan Speed Selector Switch and Display When it is set to MANUAL mode, fan speed on LCD display is as follows.

Press UP or DOWN of fan speed selector switch, and auto control of fan speed is released, and "AUTO" indicator lamp on LCD display (5) goes out.

2-41

2

2. MACHINE FAMILIARIZATION 9. Setting Temperature Display Switching Function from/to F degrees to/from C degrees The setting temperature display can be switched from/to F degrees to/from C degrees.

While the fan is operating, press "down" and "up" switches (7) simultaneously for 5 seconds or more, and the display is switched form/to Fahrenheit to/from Celsius. (But the unit is not displayed.)

7

10. Treatment of Season In and Off (1) Season in Contact our dealer/distributor for checking and service of air conditioner before air-cooling season (season in) so that the air conditioner is used in good condition for a long time.

(2) Season off Operate air conditioner for several minutes once a week in the period of out of season (season off).

The operation maintains the air conditioner in good condition preventing short of oil in each part of compressor.

2-42

2. MACHINE FAMILIARIZATION 2.3.9

HANDLING OF SEAT BELT

Install the seat belt properly or the fundamental performance may not be achieved.

-Make sure that there is no abnormality on the belt attaching bracket and bolts before fastening the belt.

-Check attaching bolts which are used to secure the belt to the seat for loosening and tighten loose bolts again.

-Do not fail to fasten the belt during operation.

How to Fasten Seat Belt

2 3

1

2

1. Since this seat belt is equipped with take-up motion, the adjustment of length is unnecessary.

2. Check that the seat belt (1) is not twisted, and pull the seat belt out.

3. When fastening seat belt, pull it out a little longer than the required length and insert it into buckle until clicking sound is heard.

Release hand, and the length is automatically adjusted and the buckle is locked.

How to Unfasten Seat Belt 1. Press the red button (3) of the buckle (2), and the belt (1) is unfastened.

2-43

2. MACHINE FAMILIARIZATION 2.3.10 OPERATOR SEAT The operator seat incorporates several adjustment mechanisms to insure operator comfort, ease of operation and operator safety. The adjustment areas are as follows.

When adjusting the operator seat, pay attention to hands in order not to be caught between handle and seat.

A. Operator Weight Adjustment Rotate the adjustment knob (1) until weight close to the operator's weight is at the top end of the dial. (Not equipped in Asia.)

B. Seat Height Adjustment 1.

Pull height adjustment lever (2) up to raise or lower rear of seat.

2.

Push height adjustment lever (2) down to raise or lower front of seat.

C. Seat Reclining Adjustment 1.

Pull reclining adjustment lever (3) up to set desired reclining angle.

2.

Release reclining adjustment lever to lock seat in position.

D. Seat Front to Back Adjustment Pull up on seat adjustment bail (4) and move seat forward or backward to desired position E. Arm Rest Adjustment Lower arm rest (5) and with finger, turn adjustment wheel until arm rest is in desired position.

To fine-adjust the angle of arm rest, turn control dial (8).

F. Head Rest Adjustment 1.

Move head rest (6) forward or backward to desired reclining angle.

G. Lumber Support (7) It is possible to adjust the force which is supporting the lumber in 5 steps by turning the knob in counterclockwise.

With turning the knob in counterclockwise the supporting force is raised and returns to the condition before adjustment at 6th step.

1 3

2

4

6 (F) (F) (C) (B)

7 (B)

(D) (G)

(A)

4 5

8

2-44

(E)

(A)

2. MACHINE FAMILIARIZATION 2.3.11 ARM REST ADJUSTMENT The height of right/left arm rests is adjustable in 4 steps.

1. Open the clamp (1) in the direction of arrow.

2. Push the protruded pin (2).

3. Slide the armrest up and down to adjust the height of armrest.

1

2

2

2.3.12 ADJUSTMENT OF CONTROL LEVER The height of right/left control stand is adjustable in 3 steps.

1. Remove bolt (1).

2. Adjust the height of hole on plate (2) to your easy to operate position and tighten plate (2) to the fixing position with bolt (1).

3. Similarly, adjust stand height on the other side by procedure 1) and 2).

2

1

B A

A : Low position B : Middle position C : High position

C

2-45

2. MACHINE FAMILIARIZATION 2.3.13 OPERATOR CAB

When necessary to leave from the operator seat, lock the safety lock lever.

After the control lever is unexpectedly touched without the safety lock lever locked, this may cause serious accident resulting in injury and death.

A. Cab Door Lock This is used to fix door in the condition where the door is open.

1. Push door against catch (1) and door is fixed.

2. When necessary to open the door, push down lever (2) on the left side of operator seat and the catch is released.

3. When necessary to fix the door, fix door to the catch securely.

2 1

In operation, lock the door securely even if it is on either open side or close side. When not locked, the door may be open unexpectedly and this might cause the injury. And also it may cause the failure of machine.

B. Releasing Door Lock from Inside of Cab When necessary to open the door from the inside of cab, pull lever (3) by hand and the door opens.

3

2-46

2. MACHINE FAMILIARIZATION C. Opening and Closing Front Window

-The front window should be opened and closed in the condition where the machine is parked in level and locked securely. If the lock is released in the forward tilting position of machine there is a possibility of falling of the front window.

-When closing the front window, the closing speed increases due to the weight of front window. Hold and close it by both hands securely.

-When storing the front window in, pull up the safety lock lever to the "LOCKED" position and stop the engine.

1.

Park the machine on the level ground, put the bucket on the ground, pull up the safety lock lever to the locked position and stop the engine.

A

2

2.

Push lock lever (4) on the upper center part of window (upper) right and release the lock.

3.

Hold and push up the handle on the upper and lower parts of the front upper window. After the front upper window reached to the end on the rear side of roof, it is locked automatically.

And then make sure that it is locked securely.

4

4.

When closing the front upper window, close it by the reverse procedure of that in above items 2.to 3.

5.

When closing the front window, push the upper sides of front window forward and lock it securely.

To prevent from catching your hand between windows, open and close the front window slowly. The work in no locking and incomplete locking conditions might cause injury.

2-47

2. MACHINE FAMILIARIZATION D. Removing & Storing Lower Front Window 1. After placing upper front window in ceiling, hold lower front window by hands and remove it from window frame.

2. Store the removed lower front window in holder (5) on the left rear side of cab securely.

LOCK

5

E. Cab Room Lamp a. Turn cab lamp “ON” by pushing the lamp switch way up. b. The lamp goes out at the neutral position. c. Turn "OFF" by pushing switch all the down ward.

OFF ON

OFF ON

2-48

2. MACHINE FAMILIARIZATION 2.3.14 EMERGENCY ESCAPE FROM CAB 20

If it is impossible to open the cab door in an emergency, escape from the cab by the following way.

1.

Open the front window and escape through the front window.

2.

If it is impossible to open the front window, break the front window glass by using life hammer (1) provided on the right rear side of cab.

3.

If the front window is unavailable to escape, break the rear window glass by using life hammer (1).

2 For how to open the front window, see item "Opening and closing front upper window".

Pay attention to the broken pieces so as not to be injured when breaking the window glass.

Labels (2) indicating the emergency exit are affixed on the rear windows.

4.

If it is impossible to use both front and rear windows for escape, open and escape from the skylight.

2

REAR INSIDE OF CAB

2-49

2. MACHINE FAMILIARIZATION 2.3.15 FUEL PUMP Fuel pump is located in back of fuel tank. Using starter key, and unlock right side door.

A. Filling Tank Using Auxiliary Fuel Pump The fuel pump and suction hose are located in the fuel box on the front side of the fuel tank.

Use it in the following procedure.

1.

2.

3.

4.

5.

6.

7.

Fuel pump Suction hose Suction filter ON / OFF switch Power / Low tension (LED lamp / Green) Full tank / No fuel (LED lamp / Yellow) Run / Alarm (LED lamp / Red)

2 3

1 5

IN

OUT 4

2-50

6

7

2. MACHINE FAMILIARIZATION A.1 Operation 1.

2.

3.

4.

Put the bucket on the ground, and stop the engine.

Turn starter key switch to "ON" or "ACC" position.

Remove fuel fill cap.

Before refilling the fuel, loosen the screw of the filter at the end of suction strainer by hand. By expanding the strainer, the strainer gets the suction function (As shown in figure). The pump does not suck the fuel if you do not loosen the filter.

5. Press the "ON/OFF" switch for 1 minute or longer, the "POWER/LOW TENSION" green lamp lights up.

As the fuel delivery starts and "RUN/ALARM" red lamp lights up. And fuel filling starts.

6. After refueling, press "ON/OFF" switch to stop the pump. (All LED lamps are turned off) Tighten screw of the suction filter to original length as shown in figures.

7. Install fuel fill cap.

2

-One operation time of pump is limited up to 10 minutes by a timer control. If the time exceeds 10 minutes, pump stops automatically. ("Yellow LED lamp" is lit) -Despite empty fuel tank, if pump is operated, pump stops automatically after 1 minute to protect the pump. ("Yellow LED lamp" is lit) A.2 Maintenance ONCE A WEEK: Check that the pipe connections are not loose to prevent any leaks.

Check and keep the filter installed on the suction line clean.

ONCE A MONTH: Check the pump body and keep it clean and free of any impurities.

Check that the electrical supply cables are in good condition.

2.3.16 ENGINE ROOM LAMP This lamp is located on the back side of engine hood.

When checking and maintenance of engine is performed, turn switch (1) of the lamp on. To turn off the light, turn starter switch to "OFF" position.

2-51

1

2. MACHINE FAMILIARIZATION 2.3.17 OTHER EQUIPMENT (ACCESSORY) A. Grease Gun Holder This is provided on the inside of cover on the left rear side of machine. When the gun is not used, put it on this holder.

Be sure to store a grease gun in this grease gun holder.

B. Cup Holder This is provided on the right side console in the cab.

This is used to put drinks, etc. in.

C. Ash Tray When desired to use ash tray, open the cover by hand.

Put out of fire of cigarette completely, and put the cigarette in ash tray. And close the cover of ash tray securely.

2-52

3. MACHINE OPERATION

3. MACHINE OPERATION

3

3-1

3. MACHINE OPERATION

3-2

3. MACHINE OPERATION

3.1

MACHINE OPERATION

3.1.1

EVERYDAY CHECK-UP

A. Daily Inspection Before starting the engine, walk around the machine to check for any loose nuts and bolts, any oil, fuel or coolant leakage, and the condition of attachment and hydraulic system.

Check for any looseness in the electrical wiring and for any accumulated material (leaves, dirt , etc.). Repair and clean as necessary.

The deposit of combustible, fuel leakage and oil leakage in heated area around the engine, muffler and battery may cause fire of machine. Check the area sufficiently, and if the abnormality is found, repair it or contact our dealer/ distributor.

1.

2.

3.

4.

5.

6.

7.

8.

9.

Check the engine for any oil, fuel or coolant leakage. Repair as required.

Check the area around the engine and radiator for any accumulated material and remove as required.

Check the hydraulic equipment, hydraulic oil tank, hoses, and joints for oil leakage, and repair as required.

Check the travel system, such as the crawler, idlers, and sprockets, for any damage or wear, and the bolts for looseness.

Check the attachments, cylinders, linkages and hoses for any cracks, wear or looseness and repair as required.

Check the door, cover, steps and handrails for damage, and the bolts for looseness. Repair and tighten bolts as required.

Verify that the gauges and the monitor panel (gauge cluster) function properly.

Check rear view mirror for abnormality, and if abnormality is found, repair it.

Clean the surface of mirror and adjust the angle so that the rear sight is visible from the operator seat.

Check seat belt and attaching metal for possible damage and if damaged, replace it with new one.

3-3

3

3. MACHINE OPERATION 3.1.2

CHECKING BEFORE STARTING ENGINE

The following checkup should be performed once before the first engine startup in a day.

A. Checking Coolant Level for Shortage and Making Up

-Do not open radiator cap if not required.

Check coolant level of the reserve tank (1) when engine is cooled down.

-Never remove radiator cap when engine is hot. Allow engine to cool down before removing radiator cap.

1. Open left side door and check coolant level of reserve tank (1).

2. Open side door of radiator with starter key and check that the coolant level is in the range of FULL (A) - LOW (B) of reserve tank. If shorted, remove filler cap (2) of reserve tank and supply to FULL (A) level.

3. After supply, tighten the cap securely.

4. When the reserve tank is empty, after checking it for oil leak check radiator coolant level for shortage, and if shorted, first supply coolant to the engine and then to the reserve tank.

5. Close the side door on the left side face of machine and lock it with starter key.

3-4

2 1 A B

3. MACHINE OPERATION B. Checking Oil Level of Engine Oil Pan and Making Up

Immediately after engine is stopped, there is a possibility of getting burn with heated parts and oil. Start working after the temperature is not hot.

-Make sure the machine is on firm level when checking engine oil level.

-Always make sure to check engine oil level before starting the engine.

-Keep the engine to standstill for at least 30 minutes, when checking engine oil level after working.

1. Open engine hood and support it with stay.

2. Pull out oil level gauge (G) and wipe oil with a clean cloth.

3. Insert oil level gauge (G) in oil pan fully.

4. When the level is in the range of H - L of oil level gauge (G) it is proper. If the level is insufficient for L level, make up engine oil for the shortage through oil filler cap (F).

If the oil is contaminated and deteriorated, change it ahead of schedule without depending on the periodic change interval.

For oil in use, refer to "4.3 LUBRICANT, FUEL & COOLANT SPECIFICATIONS" in Chapter 4.

5. When the oil level is H level or higher, drains excess engine oil though drain plug (P) and check the oil level again.

6. If the oil level is proper, insert level gauge (G) securely, close engine hood and lock it with starter key.

F

3

G

H L

P

3-5

3. MACHINE OPERATION C. Checking Fuel Level and Making Up

-Use diesel fuel only and stop engine before refilling.

-Do not overflow fuel while refilling. It may cause damage to the fuel system and cause oil spouting. Clean up all spilled fuel to prevent fire.

-Dispose of all hazardous waste in accordance with government environmental laws and regulations.

-It is possible to operate machine for 2 days (8 hours a day) in general use when the tank is full. Be sure to fill it up to the brim after the work in 2nd day was finished. But do not supply with fuel to the level more than necessary (to the top end of tank). There is a possibility of overflowing because the fuel expands as the outside air temperature rises.

-Refer to "2.3.15 FUEL PUMP", see chapteer 2. for refueling with fuel pump.

-Use specified diesel oil for fuel.

This engine is equipped with electronic control high pressure fuel injection system to obtain the features like excellent fuel consumption and emission in clean condition. This system requires the parts in high precision and high lubricating ability. Therefore if low viscosity fuel in low lubricating ability is used, the durability may be notably lowered.

1 1. Check fuel level with fuel gauge by turning starter switch on. The fuel level is low when the fuel gauge reads close to E point.

2. Stop engine with starter key, remove filler cap (1) of fuel tank and make it up with fuel making sure of the level.

When strainer is fitted to filler port, do not remove the strainer for making up.

3. When dirt is adhered on strainer (2), take out the strainer and clean it with light oil or air gun, and then fit it to filler port again.

4. Refer to "4.3 LUBRICANT, FUEL & COOLANT SPECIFICATIONS" in Chapter 4.

-Fuel tank capacity: 120 L (31.7 gal) 5. After refueling, tighten filler cap (1) securely.

2

3-6

3. MACHINE OPERATION D. Fuel Pre-Filter Drain The fuel pre-filter isolates water that mixes in with the fuel. The case is equipped with a float. When water accumulates, the float rises. When the float rises to the level line, drain water.

1. The fuel pre-filter (1) is installed in front of counterweight on the right rear side of machine.

2. Open engine hood and support it with stay.

3. Put container for drain oil under drain hose (2).

4. Loosen drain plug (3) and air bleed plug (4) and drain water collected in fuel filter (1) in the container.

5. After draining, tighten drain plug (3) and air bleed plug (4) securely.

6. Release the stay which is supporting hood, close engine hood and lock engine hood.

4 1 2 3

3

E. Checking Radiator, Oil Cooler and Filter 1. Using starter key, unlock side door on left side of counterweight, and open it.

2. By visual check, check mud, dust and leaves which contaminate filter (1).

3. When filter is contaminated heavily, refer to "4.15 250 HOUR (3-MONTH) INSPECTION MAINTENANCE PROCEDURE" and clean these filters.

3-7

1

3. MACHINE OPERATION F. Check Hydraulic Oil Level

It is very danger because the inside of hydraulic tank is heated and pressurized.

When removing filler port plug, stop engine and remove breather top end cap (1) and then release pressure from hydraulic oil tank by pressing the valve head.

For safe operation on inclines, the hydraulic oil level must be maintained between "Proper Level" and "Upper Limit" mark.

Checking 1. The hydraulic tank is installed on the right side.

2. Move the machine to firm level ground and set it in the hydraulic oil level check position.

3. Check the oil level through sight level gauge (G) provided on the side of the hydraulic tank.

Hydraulic oil level should be between H and L. Oil level varies depending on oil temperature.

Check the oil level referring to the followings.

• Before starting : "L" level oil temp. 10 to 30 C degree (50 to 86 F degree) • Normal operation : "H" level oil temp. 50 to 80 C degree (122 to 176 F degree)

1

H G L

Avoid overfilling. It causes damages on hydraulic equipment or oil spouting.

For make up procedure of hydraulic oil, refer to section "4.19.A Change Hydraulic Oil" in Chapter 4.

3-8

3. MACHINE OPERATION G. Checking Belt Tension

Rotating parts can cause injury.

Keep away from fan and belt when engine is running.

Stop engine before servicing.

If defects such as cuts or surface separations are found during inspection, replace the belt. Keep oil and grease away from the belt, since they may cause the belt to slip and shorten the service life.

Check the fan and alternator belt for insufficient tension, wear, and damage. Insufficient belt tension may cause battery charge failure, engine overheating, or abnormal belt wear. If too much tension is applied to the belt, the bearings or belt may be damaged prematurely.

Apply a force of 98 N {22 lb} to the center of belt between pulleys, and measure the belt deflection. The table below shows normal condition.

3

Belt

When new belt replaced mm (in)

When inspected mm (in)

Force N (lbf)

Alternator, Fan

4 to 6 mm (0.16 to 0.24")

7 to 9 mm (0.28 to 0.35")

98 (22)

Air-conditioner

3 to 4 mm (0.12 to 0.16")

5 to 6 mm (0.20 to 0.24")

24 (5.1)

-When replace with new belt, there is a lack of initial adaptability of the belt. Run the engine at idling speed for about three or five minutes. After that, adjust the belt tension again.

-New belts get complete initial elongation after being run about two hours.

See the section "4.15 250 HOUR (3-MONTH) INSPECTION & MAINTENANCE PROCEDURE" for details on the inspection and adjustment procedure for the belt.

3-9

3. MACHINE OPERATION 3.1.3

ADJUSTING OPERATOR SEAT

-Adjust the operator seat before starting operation or at the time when operator was changed.

-Be careful not to put hands between handle and seat stand.

Adjust the operator seat position so that the control lever, each control pedal and switch can be easily manipulated in the condition where operator takes seat and has his back fitted to the back seat.

For adjustment of operator seat, see "2.3.10 OPERATOR SEAT".

3.1.4

ADJUSTING MIRROR

Two rear view mirrors are equipped at left side of cab and on the hydraulic tank cover.

Adjust all mirrors so that the area in the blind spot may decrease most when sitting on the driver's seat.

Before any working, make sure that the mirrors are correctly adjusted. If the mirror position is incorrectly adjusted, the best all-around operator view is not obtained. This can result in serious injury, death, or machine damage.

3-10

3. MACHINE OPERATION 3.1.5

CHECKING FUNCTION OF GAUGE CLUSTER

Before starting the engine, check the warning display and gauge according with the following procedures: 1. Make sure the safety lever is in the "LOCKED" (Up) position.

2. Make sure all control levers are in the "NEUTRAL" position 3. Insert starter key and start engine.

S

3 When starting engine, if warning is displayed on the multi-display, stop engine immediately and contact our dealer/ distributor.

3.1.6

CHECKING WORK LIGHT

While the key position in the starter key switch is being "ON" position, turn on the work light switch to check the lightening of work light.

If it does not lighten, presumably the light bulb is burned out or electrical wire is broken.

Contact our dealer/distributor for repair.

3-11

3. MACHINE OPERATION 3.1.7

STARTING ENGINE

After making sure that no one is stayed and no obstruction is left around the machine, sound horn and start the engine.

-Do not hold the starter key switch in the START position for more than 15 seconds. If the engine does not start, return the starter key switch to the OFF position, wait 30 seconds, and then try it again.

-When starting engine, if warning is displayed on the multi-display, stop engine immediately and identify the cause, and then repair it if necessary.

3-12

3. MACHINE OPERATION A. Start-Up Under Normal Conditions 1. Make sure that safety lock lever (1) is set to the "LOCKED" (Up) position.

A. Locked (Up) Position B. Unlocked (Down) Position 2. Make sure all control levers are set to the "NEUTRAL" position.

3. Set throttle potentiometer (2) to low idling position.

4. Turn the starter key (3) to "ON" position, and confirm the operating condition of multi-display.

5. Turn the starter key switch (3) to the START position to start the engine and release after starting the engine.

6. Release the starter key switch immediately after the engine starts.

The starter key switch will return to the "ON" position by itself.

1 A

B

3 3

2

B. Start Up in Cold Conditions In cold weather, due to the increase in oil viscosity and decrease in battery performance, starting the engine may be difficult. Use the preheater to start the engine easily under these conditions.

1. Turn and hold starter key switch (1) to "ON" position 2. When engine coolant temperature gauge detects -6 degrees or lower, the glow plug starts heating automatically.

3. After 30 seconds, turn the starter switch key to "ON" position. And start the engine by the procedures from 3. to 6. which are explained in the section "Start-Up Under Normal Conditions".

4. After engine starts, to prevent the occurring of white smoke exhaust, the preheating continues and stops automatically.

3-13

1

3. MACHINE OPERATION C. Using Booster Cables Observing the following precautions when using booster cables to start a disabled machine.

AVOID BATTERY HAZARDS -Flammable gas (hydrogen gas) is generated in the battery. Do not allow sparks or flames to come in contact with batteries to avoid triggering an explosion.

-Do not allow the vehicle or machine used for boosting to touch metal to metal with the disabled machine.

-Wear hard hat, approved safety glasses or face shield rubber, gloves and other safety equipment when working with batteries.

-Do not allow the booster cable clips to come in contact with each other once connected to a battery.

-The negative cable, when connected to the upper frame of disabled machine, may arc causing sparks. Connect the booster cable to a ground surface in the engine compartment as far as possible from the battery.

-If the battery fluid is frozen, do not attempt to start the disabled machine. Either allow batteries to thaw and then charge or replace the batteries.

-Follow the order indicated in the next page for connecting or disconnecting the booster cables.

-Use the battery of which the capacity is equivalent to that of the machine in out of order for the machine in normal condition.

-Select suitable size for the booster cables and clips according to battery size.

-Do not use booster cables that are damaged, i.e., broken insulation, damaged clamps or damaged by corrosion.

-Connect clip securely.

-Check that the safety lock lever is to the locked position.

-Check that control lever has returned to neutral position.

-The starter key switches on both machines in normal condition and out of order must be held in off condition.

When the power was connected, it may unexpectedly start and cause accident.

Follow the order indicated in the section "3.1.7.D Connecting / Disconnecting Booster Cables".

3-14

3. MACHINE OPERATION D. Connecting / Disconnecting Booster Cables Make sure the starter key switch is in the OFF position before connecting the booster cables. Proceed as follows to connect and disconnect the booster cables.

AVOID EXPLOSION -Wrong connection of booster cables may cause explosion of the batteries. Pay special attention while connecting and disconnecting the booster cables.

-The starting system of this machine is 24 volts. Therefore the boost battery voltage in use should be 24 volts.

The application of high voltage employed for welding machine, etc. to start the engine may cause damage to the electric system.

1. Put attachment on the ground, return all control levers to neutral position and then lock the safety lever.

2. Set the starter key switch to "OFF" for both boost vehicle and disabled machine.

3. Connect the booster cable (red) clip to the positive (+) terminal on the battery of disabled machine.

4. Connect the clip from the other end of the positive (+) booster cable (red) to the positive (+) terminal on the battery of boost vehicle.

5. Connect the booster cable (black) clip to the negative (-) terminal on the battery of boost vehicle.

6. Finally, connect the clip from the other end of the negative (-) booster cable (black) to the upper frame of disabled machine, away from the battery.

7. Start the engine of boost vehicle, and run it for about 10 minutes at high idle.

8. Start the engine of disabled machine.

9. After starting the engine of disabled machine, remove the booster cables in the reverse order of the above connection order.

10.Check and repair the cause of the problem of the charging system on the disabled machine.

3-15

3

3. MACHINE OPERATION 3.1.8

STOPPING MACHINE ENGINE

Run the engine for at least 5 minutes at low speed before stopping.

Avoid damage to engine. Stopping the engine while running at high speed will cause damage from increased engine temperature affecting seals and oil.

1. Place the attachment on the ground before stopping the engine.

2. Place the safety lock lever in the "LOCKED" (up) position before leaving the cab.

3. Turn the throttle potentiometer (1) all the way forward to "LO" speed position for 5 minutes to lower the coolant temperature.

4. Turn the starter key switch (2) to OFF to stop the engine.

5. Remove the starter key switch (2).

3-16

2

1

3. MACHINE OPERATION 3.1.9

INSPECTION AFTER STARTING ENGINE

Check and ensure the following items after starting the engine.

-Careless movement of any control levers may cause unexpected movement of the machine. Set the safety lock lever to the "locked"(up) position before leaving the cab.

-Make sure the swing area of machine is clear of people and obstacles before operating. Know the position of the travel motors before starting traveling and sound horn before starting operation.

A. Safety Lock Lever 1. With the engine running, set the safety control lever to the "LOCKED" (up) position.

2. Move all control levers.

3. Make sure the all functions do not operate when the safety control lever is in the "LOCKED" (up) position.

4. Move the travel control levers to make sure the machine does not move.

Locked

Unlocked

AVOID INJURY OR DEATH If any improper operation is found, stop the engine immediately. Contact the dealer/distributor and have the machine repaired to avoid any unexpected machine movement.

3-17

3

3. MACHINE OPERATION B. Checking Function of Engine and Multi-Display

When warning was displayed on the multi-display, stop the engine immediately and investigate the cause of error.

1. Check leak for oil and water around the engine.

2. Check that warnings of battery charge and engine hydraulic pressure are disappeared, and the readings of engine coolant temperature meter (1) and fuel level meter (2) are correct.

3. Check that exhaust sound and exhaust color and vibration are normal.

S 1

-Check the exhaust gas color (After warming-up and at no-load) Colorless or light blue : Normal Black : Abnormal, incomplete combustion White : Abnormal, oil combustion due to oil loss by way of piston ring or valve guides -Due to cold weather in winter the smoke may appear white. Be careful not to get confused.

3-18

2

3. MACHINE OPERATION 3.1.10 MACHINE WARMING-UP

-The proper hydraulic oil temperature for this machine is about 50 C degrees.

The abrupt operation when the hydraulic oil temperature is 25 C degrees or less may cause serious trouble for hydraulic equipment. Warm up the hydraulic oil before starting the work.

-The operation of attachment with insufficient warming-up makes the reaction of attachment to the control lever slower and may move the attachment against the purpose of operator. Do not fail to perform the warming-up.

Especially in cold weather, the sufficient warming-up is necessary.

Perform the warming-up by the following procedure.

A. Engine Warm-Up

-The revolution up of engine while idling may cause failure and trouble to the engine. Do not revolution up the engine while idling.

1. Allow the engine to run for 5 minutes under no load conditions with throttle potentiometer (1) at "LO" idle position.

2. When the pointer of engine coolant temperature (2) moves and points to the range in white, the warming-up of engine is completed.

10:25 S

1

2

3-19

3

3. MACHINE OPERATION B. Warming Up Hydraulic Oil 1.

Make sure that safety lock lever (1) is set to the "UNLOCKED (DOWN)" position.

A

2.

Move throttle control to "HI" idle position.

B 1

3.

Move right control lever slowly to the stroke end of bucket digging side, and execute relief action for about 2 minutes.

And then extend and/or retract the rod of each cylinders several times slowly for the purpose of circulating of warm hydraulic oil.

4.

When the machine warming up is not sufficient, move the control lever to the stroke end of bucket digging side, and execute more 2 minutes relief operation.

And then extend and/or retract the rod of each cylinders several times slowly for the purpose of circulating of warm hydraulic oil.

Also operate swing and travel slowly and circulate the warm hydraulic oil.

While operating the machine with cold hydraulic oil, the operator may experience slow or unexpected movement of functions.

Damage to the hydraulic components may result due to the cold oil not providing adequate lubrication.

3-20

3. MACHINE OPERATION 3.1.11 WORK MODE SELECT SWITCH Press the work mode select switch (1) in order, and "S" --> "H" mode can be selected.

Select the effective work mode according to the work condition and working target from the table shown below.

For the selected work mode, refer to the table shown below.

-S mode: For standard excavating work -H mode: For heavy duty excavating work

10:25 S

1

3 -The initial setting (default) of work mode had been set to "S" mode at factory.

As for the work mode after the engine starts, the mode that was used the last time engine was stopped is automatically set.

Check that the selected mode conforms to the work before starting work.

-Check that the attachment in use conforms to the work mode before starting work. If not conformed, select proper mode with the work mode select switch.

-The operation under improper work mode may cause damage to machine.

-When the work mode lamp is flickering, it tells the wrong choice of the work mode.

Kontrollmodus

S-modus

H-modus

Kjennemerke

10:25 10:25

M

erknader

”S-modus” egner seg til standard grave- og lastearbeide. Denne modusen reduserer også forbruket av drivstoff og fordeler arbeidsbelastningen.

”H-modus” egner seg til tungt gravearbeide som prioriterer arbeidsbelastning til høy hastighet.

3-21

3. MACHINE OPERATION 3.1.12 CONTROLS DECAL A. Operating Pattern The operating and travel controls of this machine are factory set to ISO standard operating patterns for optimum performance of the machine and its systems.

Check and make sure that operating pattern control matches the decal provided inside the right side window.

B. Operating Pattern Decal Figure is a representation of the “CONTROLS” decal located on the right side window inside the operator cab.

Study this decal and understand the directions each control can be operated and the functions associated with each movement of particular control. Detailed instructions for each control and its functions are explained on the following pages of this section. Should this decal become damaged or missing, install new decal Part Number PW22T01048P1.

HYDRAULISKE KONTROLLSPAKER

VENSTRE KONTROLLSPAK

VENSTRE HØYRE KJØRESPAK KJØRESPAK OG -PEDAL OG -PEDAL

HØYRE KONTROLLSPAK

BULLDOZERSPAK

3-22

3. MACHINE OPERATION 3.1.13 MACHINE OPERATION The following instructions are aimed at providing an operator with the basic function of each hydraulic control. Use these instructions, and practice with a machine, will allow a given operator to become more efficient in the operation of this equipment. Each operator must read thoroughly, understand, and follow these basic instructions along with all safety precautions found in this manual and on the machine before operating this equipment.

A. Caution In Machine Operation

3

-Before start traveling, see around the machine for safety and sound horn.

-Do not permit for people to gain access to the machine.

-If the operation of control lever in auto accel operation could cause abrupt increase of engine speed. Pay attention to the operation.

-The display on the multi-display does not completely ensure the condition of equipment. The daily check should follow not only the display on multi-display but also the instructions in the Manual.

-When abnormality was detected in operation, stop the machine immediately and take proper measure.

-Do not operate the machine until the abnormal section is repaired and recovered. The operation in abnormal condition may cause serious accident.

3-23

3. MACHINE OPERATION B. Machine Travel

-Identify the travel motor position before traveling. When the travel motor is positioned on the front side the traveling operation reverses.

The normal traveling for the machine is that the travel motor is on the rear side and the track idler is on the front side.

-Sound horn to warn workers in the site.

F : Forward N : Neutral (Stop) R : Reverse

F

N R

B.1 Forward/Reverse Travel 1. Make sure the safety lock lever is in the "UNLOCKED" (down) position. Operate the boom, arm, and bucket control levers to raise the attachments from the ground.

2. To move the machine forward, push both (right and left) travel levers toward the front of machine. To move the machine in reverse, pull back both travel levers.

Travel speed changes depending on how far you push or pull the levers.

Forward/Reverse Travel

Do not move the travel speed switch during traveling. And change the travel speed in low (1st) speed when the machine is running on the downhill, and is loading/unloading on/from trailer. The sudden change of machine stability may cause accident resulting in injury and death.

3-24

3. MACHINE OPERATION B.2 Pivot Turn • • • •

Push the left travel lever toward front of machine to turn machine RIGHT. Push the right travel lever toward front of machine to turn machine LEFT. Pull the left travel lever back to turn machine LEFT in reverse.

Pull the right travel lever back to turn machine RIGHT in reverse.

Pivot Turn B.3 Counter Rotating Machine (Spin Turn) To counter rotate machine to the left, pull left travel lever back and push right travel lever forward.

To counter rotate machine to the right, pull right travel lever back and push left travel lever forward.

3

Counter Rotating Machine C. Changing Travel Speed (1st, 2nd Speed) The travel speed change (1st, 2nd speed) switch (1) on the switch panel is available to change the travel speed from/to low speed (1st speed) to/from high speed (2nd speed).

When starting engine, the switch is automatically set to low speed (1st speed).

The mode is changed in order of turtle (1st speed) --> rabbit (2nd speed) --> turtle (1st speed) --> rabbit (2nd speed) each time the switch is pressed.

10:25 S

1. Take travel position during the engine being in operation.

2. Travel with travel lever or pedal.

3. The icon "turtle" is displayed for 1st speed and rabbit for 2nd speed.

1

3-25

3. MACHINE OPERATION D. Travel Stop

Do not stop the machine suddenly, but stop it after slow traveling.

Return the right and left travel levers (1) to neutral (N) position. The machine stops traveling.

N N 1

3-26

3. MACHINE OPERATION E. Machine Operation in Water

Be careful not to immerse the slewing bearing, slewing pinion and swivel joint into the water or mud. If the machine is operated in water or mud, the slewing bearing and others may be worn abnormally.

If water or mud comes up to the slewing bearing level, put grease in slewing bearing unit the old grease comes out.

If water or mud goes higher than the upper frame level, contact the dealer/distributor for cleaning or repair.

1. Make certain travel motor location is known before performing any travel operation.

2. Travel on firm, level surfaces as much as possible.

3. When traveling on rough terrain, travel in SLOW speed with engine at a low idle.

4. Travel with the travel motors in back of the machine for long distance travel.

5. When traveling or operating machine on snow or icy surfaces, clean track shoes frequently to prevent clogging. This will help keep the machine from sliding unexpectedly.

6. Keep a safe distance from stationary objects and electrical power lines.

7. Be aware of load capacities of bridges and road shoulders. Reinforce if necessary.

8. Use decking or plating to protect road surfaces as much as possible. Be careful when turning or spinning machine on asphalt pavement.

9. Do not allow large or heavy objects to strike travel motors.

10.Do not travel over large objects such as boulders rocks etc.

11. If necessary to travel or operate machine in a river or other water, the bed must be firm and water current slow.

Water must not be deeper than indicated in the chart in.

12.On soft ground or mud the machine can sink. Stay constantly aware of undercarriage position.

3-27

3

3. MACHINE OPERATION F. Getting Out of Soft Ground

AVOID INJURY Attempting to free a machine that is stuck can be hazardous. Avoid operating on soft ground. The machine operator must be careful to avoid injury to himself and others while attempting to free the machine.

If possible, avoid traveling on a soft ground. Avoid getting caught in the mud. In the event that the machine gets caught in the mud, get out of it as follows.

F.1 One Crawler Belts/Tracks Get Caught in Mud When either side of crawler belts/tracks gets caught in the mud, lay logs or boards on the mud to form a base.

Operate the boom and arm to form an angle between boom and arm of about 90 to 110 degrees and push on the ground with the bottom of the bucket to lift the machine body up to climb on the logs or boards.

F.2 Both Crawler Belts/Tracks Get Caught in Mud When both sides of crawler belts / tracks get caught in mud and the machine does not move due to skidding, provide logs and boards, as described in the above section. Using the bucket, dig into an area of the hard ground. Then move the bucket control to pull the machine toward the hard ground.

If this is not possible, get expert help to free the stuck machine.

If the machine will not travel due to being stuck in mud, sand, gravel or on soft ground, lift each crawler belt / tracks off the ground by placing the bucket on the ground and pushing the boom and arm against the ground. Raise the crawler belt / track a small distance off the ground.

Scrape the mud, sand, or gravel off the crawler belts / tracks.

This material may be cleared by rotating the crawler belts / tracks in forward and reverse with the crawler belt / track raised.

Operate the machine at the operator's seat. Do not allow any person to come near the machine.

3-28

3. MACHINE OPERATION G. Machine Attachment & Swing Controls The following instructions are to be used with hoe bucket attachment only. If other attachments are being used, consult the operator's manual for the particular attachment.

Read, understand and follow all safety precautions during all operations of this machine and its attachment(s).

G.1 Boom Operation Operation of the boom is performed by pushing and pulling the R.H. control lever forward and backward. Boom speed is determined by how far the lever is activated.

1. Pulling R.H. control lever BACK raises boom.

2. Pushing R.H. control lever FORWARD lowers boom.

3. Returning R.H. control lever to the neutral (center) position stops operation of the boom.

3 G.2 Arm Operation Operation of the arm is performed by pushing or pulling the L.H. control lever forward and backward. Arm speed is determined by how far the lever is activated.

1. Pushing the L.H. control lever FORWARD moves the arm out.

2. Pulling the L.H. control lever BACK moves the arm in.

3. Returning the L.H. control lever to the neutral (center) position, stops operation of the arm.

G.3 Bucket Operation Operation of the bucket is performed by moving the R.H. control lever to the right or left.

1. Moving the R.H. control lever to the LEFT operates the bucket IN (digging).

2. Moving the R.H. control lever to the RIGHT operates the bucket OUT (dumping).

Be careful when operating certain attachments close to the cab. Certain attachments can hit and damage cab. Stop attachment a safe distance away from cab to avoid damage or injury.

3-29

3. MACHINE OPERATION G.4 Swing Operation

Use swing flashers during swing operations.

Swing operation is performed by moving the L.H. control lever to the right and left. Swing speed is determined by the amount the lever is moved.

1. Moving the L.H. control lever to the LEFT swings the machine to the left.

2. Moving the L.H. control lever to the RIGHT swings the machine to the right.

3. Returning control to the neutral (center) position stops swing.

PUSH LEFT TO SWING LEFT

RE

Make certain area is clear of obstacles and persons before beginning swing operation of the machine. Sound horn before beginning swing operations.

PULL RIGHT TO SWING RIGHT

3-30

3. MACHINE OPERATION H. Dozer Operation BEFORE OPERATING THE DOZER BLADE

Read, understand and follow all safety precautions and operation procedures found in this manual before operating the machine or any attachment.

The dozer blade operating lever (1) is located on the right side of the right hand operator console basic function is to lift or lower the dozer blade.

1. Start machine and place the safety lock lever in the "UNLOCKED" (Down) position.

2. Move throttle potentiometer to the "Hi idle position".

3. Using boom, arm and bucket controls set the attachment to desired position.

4. Pull (A) the dozer blade operating lever to lift up the blade.

5. Push (B) the blade operating lever forward to lower the dozer blade.

B

1

A

3

A

B

Dozer blade control function is live at all times. That is, even with the safety lock lever in locked up position.

3-31

3. MACHINE OPERATION 3.1.14 PRACTICES TO IMPROVE EFFICIENCY

A. Use Arm in Action Operate the bucket at shallow depths and use the arm in action to fill the bucket. Setting the bucket too deep will decrease the machine's efficiency.

B. Operate Boom Smoothly Always begin and end boom operation slowly with smooth, careful movement of the control lever. Do not perform sudden starts and stops of the boom as this creates unnecessary stress on the machine and its components.

C. Bucket Teeth Direction Always point bucket teeth in the direction the machine will be digging to reduce digging resistance and the possibility of bucket teeth damage.

D. Maximum Digging Force Position The attachment will provide maximum digging force when the arm and boom are at 90 to 110 degrees of each other.

3-32

3. MACHINE OPERATION E. Cleaning Sand & Soil from Bucket Operate arm to a near level position and bring the bucket to a dumping position. If sand and soil do not fall out, move the bucket lever right and left a few times.

Avoid shaking out soil using shocks at the end of the bucket cylinder stroke.

F. Stop Swing Motion Early

3

To stop slewing action, release the swing lever before you get to your final point of digging or dumping.

3-33

3. MACHINE OPERATION G. Back Filling & Leveling For back filling and leveling work after digging, move the bucket back and forth horizontally.

Do not push or pull material with the bucket like a bulldozer when using the machine to level material.

1. In leveling ground toward machine, pull the arm gently, lift the boom a little and when the arm has passed the vertical point, lower the boom gently and manipulate the machine so the bucket moves horizontally.

2. For leveling ground away from machine, reverse operation in step 1 above.

3. ln the above operation, bucket motion may be used together with the boom. By controlling the action of the boom work lever, you can dig a slope- like, slope facing operation.

4. Never travel with attachment touching the ground.

Severe structural damage could occur.

H. Operating The Shovel Digging with the shovel differs slightly from digging with backhoe.

1. Using the arm cylinder, scrape the ground.

2. Scrape the ground at 2 to 3 degrees to improve draining in areas near the groundwater level.

3. Be careful not to bump the reversed bucket into the cab.

4. The excavating power during shovel operations is less than that during backhoe operations.

5. If machine bucket is equipped with a lifting eye, check to make sure that the eye will clear arm with bucket cylinder in full extended (full dump) position.

3-34

3. MACHINE OPERATION 3.1.15 FLAGMAN HAND SIGNALS The following is a compilation of the hand signals to be used when a flagman is required for excavator operation.

All personnel associated with the operation of the excavator should know these signals and their meaning before attempting to operate this machine.

A. Raise Load Vertically Face machine operator, raise right forearm vertical, with index finger pointing up and move hand in a small circular motion.

B. Lower Load Vertically Face machine operator, extend right arm down, point index finger down and move hand in a small circular motion.

C. Move Load in Horizontally Face machine operator, extend right arm toward operator with hand facing operator and move hand in direction of movement required.

D. Move Load Out Horizontally Face machine operator, extend right arm toward operator with back of hand facing operator and move hand in direction of movement required.

3-35

3

3. MACHINE OPERATION E. Raise Boom Face machine operator, extend right arm out horizontally from shoulder, make a fist with thumb up.

F. Lower Boom Face machine operator, extend right arm out horizontally from shoulder, make a fist with thumb down.

G. Swing Left Face machine operator, extend right arm out horizontally from shoulder, make a fist with index finger pointing in swing direction.

H. Swing Right Face machine operator, extend left arm out horizontally from shoulder, make a fist with index finger pointing in swing direction.

3-36

3. MACHINE OPERATION I. Arm In Face machine operator, bend at elbows with arms facing operator, make fists and point thumbs in toward each other.

J. Arm Out Face machine operator, bend at elbows with arms facing operator, make fists and point thumbs out away from each other.

3

K. Counter Rotate Left Face machine operator, place right hand on top of hard hat, bend left arm at elbow to the right, make a fist with left hand with index finger pointing out and rotate hand in a reverse circular motion.

L. Counter Rotate Right Face machine operator, place left hand on top of hard hat, bend right arm at elbow to the left, make a fist with right hand with index finger pointing out and rotate hand in a forward circular motion.

3-37

3. MACHINE OPERATION M. Travel Forward Face machine operator, bend both elbows in, make fists and rotate fists one over the other in a reverse circular motion.

N. Travel Reverse Face machine operator, bend both elbows in, make fists and rotate fists one over the other in a forward circular motion.

O. Close Bucket (Bucket In or Dig) Face machine operator, hold left hand in, closed and stationary, hold right hand in, make a fist with index finger pointing toward left hand and move right hand in a small reverse circular motion.

P. Open Bucket (Bucket Out or Dump) Face machine operator, hold left hand in, open and stationary, hold right hand in, make a fist with index finger pointing toward left hand and move right hand in a small forward circular motion.

3-38

3. MACHINE OPERATION Q. Turn Left Face machine operator, raise right forearm up, make fist with right hand and hold stationary, bend left arm in, make fist with left hand and rotate left fist in a small reverse circular motion.

R. Turn Right Face machine operator, raise left forearm up, make fist with left hand and hold stationary, bend right arm in, make fist with right hand and rotate right fist in a small forward circular motion.

3

S. Move This Much Face machine operator, raise both forearms up, hands open and facing each other , move hands in laterally indicating how far to go.

T. Move Slowly Face machine operator, raise left arm out horizontally toward right shoulder with hand open and facing down, point right index finger up toward open left hand and rotate right hand in a reverse circular motion. (Raise load slowly is illustrated.)

3-39

3. MACHINE OPERATION U. Stop Face machine operator, raise left arm out horizontally from shoulder with hand open and facing down, move arm in a horizontal motion back and forth.

V. Emergency Stop Face machine operator, raise both arms out horizontally from shoulders with hands open and facing down, move arms in a horizontal motion back and forth.

W. Stop Engine Face machine operator, right arm at side, draw left thumb or index finger across throat.

3-40

3. MACHINE OPERATION 3.1.16 PARKING THE MACHINE

AVOID INJURY -Always park the machine on a hard level, surface.

-When parking on a slope is unavoidable, position the machine as shown in the figure. Block the crawler track, dig bucket teeth into ground, lower dozer blade (if equipped) to the ground. This will help prevent machine movement.

-Set the safety lock lever to the "locked" (up) position to avoid any unexpected machine movement.

-Stop the engine before leaving the cab.

-If the machine is to be parked on a road way, move the machine to the shoulder to allow passing of traffic. Also post reflective warning signs and markers at a distance from the machine to safely warn motorists. Refer to local code and regulations regarding the posting of work area warnings and markers.

1

1.

Place both travel levers (1) into the "NEUTRAL" position.

2.

Turn throttle dial (2) to low idling position and cool down for about 5 minutes.

3.

Put bucket on the ground holding the bucket bottom level.

4.

Set starter key switch (3) to "OFF" position and stop the engine, and then pull out the starter key.

3

3-41

2

3

3. MACHINE OPERATION 5.

Pull up safety lock lever (4) to "LOCKED (UP)" position.

6.

When necessary to leave from the machine, close windows, cab door and each door, and then lock it.

4

3.1.17 PRECAUTIONS AFTER OPERATION Check engine coolant level, engine oil pressure and fuel level for shortage through the use of multi-display.

1. If warnings of engine coolant and engine oil pressure are displayed, move the machine to a safe place and stop the engine. And then repair it according to applicable procedure in Chapter 4 "INSPECTION & MAINTENANCE CHART".

2. Check for any oil or coolant leakage. Check the attachment, exterior, and travel system components. If leakage and damage are found, repair it immediately according to applicable procedure in Chapter 4 "INSPECTION & MAINTENANCE CHART".

3. Fully refill with fuel. However, do not overfill (to the top of the tank) to avoid overflowing due to fluid expansion under normal temperature.

4. Remove mud, etc., stuck to the traveling components.

3-42

S

3. MACHINE OPERATION 3.1.18 MACHINE OPERATION IN ADVERSE WEATHER CONDITIONS

1. Operation in Extreme Cold a. Follow procedures in the section "3.1.7.B Start Up in Cold Conditions" as starting engine may be difficult due to extremely cold temperatures b. Use an engine oil, hydraulic oil and diesel fuel designed for use in cold climates. See maintenance section, "4.3 LUBRICANT, FUEL & COOLANT SPECIFICATIONS" for reference. Also, keep battery fully charged. c. Make certain to perform machine warm-up procedures as described in the section "3.1.7 STARTING ENGINE" to prevent premature wear or damage to pumps, motors and other components. d. Make certain that the engine coolant mixture is sufficient to keep the machine safe. Take into consideration wind chill factors when mixing coolant ratios. e. Keep battery terminals free of ice and snow. Ice and snow could cause the terminals to short circuit and cause extensive damage to the machine systems. Check the battery electrolyte (acid) level frequently and fill as necessary with distilled water. If the machine will be left outside overnight, it is recommended to remove the batteries and store in a warm area.

In regard to above c.: In extremely frigid climates, covering the radiator is a method to aid the machine warm-up. IF NECESSARY TO MAINTAIN OPERATING TEMPERATURES, COVER THE OUTER EDGES OF THE RADIATOR, LEAVING AN OPENING IN THE CENTER PART OF THE COVER - THUS AVOIDING FAN OVERLOADING. Keep a close watch on the gauge cluster for warning icons during operation. It may be necessary to use a coolant heater, fuel heater, engine heater jacket, and/or additional battery power to aid engine starting.

In regard to above d.: Mix coolant to a protection temperature of 5C degrees (9F degrees) lower than the machine will experience during operation, storage or transport.

2. Operation in Extreme Heat a. b. c. d. e.

Use an engine oil, hydraulic oil and fuel oil designed for use in hot climates. Also, keep battery fully charged.

Clean radiator, oil cooler and debris screen often to prevent damage or overheating of the machine.

Keep all belts properly tensioned.

Make certain that the engine coolant mixture is sufficient to keep the machine safe.

If the machine becomes overheated, idle the machine to help cool the engine, turn engine "OFF" and check coolant level. After filling to proper level the machine continues to over heat, stop engine, allow to cool, drain and flush entire cooling system and refill with the proper mixture of fresh, clean coolant. f. Check the battery electrolyte (acid) level frequently and fill as necessary with distilled water. g. Keep a close watch on the gauge cluster for warning icons during operation. Avoid unnecessary low speed running of the engine during operation. During slow, or no work periods, place throttle potentiometer in "LO" idle position.

In regard to above b.: Do not allow dirt and debris to accumulate in the radiator fins, oil cooler fins or debris screen.

3-43

3

3. MACHINE OPERATION 3. Operation in High Altitudes a. Due to low atmospheric pressure at high altitudes, a decrease in engine power will be experienced.

Be aware of this fact when placing machine under heavy load in high altitude climates. b. Keep close watch on the engine temperature gauge to avoid overheating of the engine.

4. Operation in Sandy and Dusty Areas a. Check the engine air cleaner elements frequently in sandy or dusty conditions. b. When air cleaner restriction lamp is lit, change filters immediately regardless of time intervals. c. Service fuel filter, water separator, and all hydraulic filters frequently.

5. Operation at Seashore or Salty Climate a. Thoroughly wash machine daily to help avoid corrosion of machined areas, electrical components and cylinder rods. b. Frequently check all mounting hardware for proper tightness. Torque to proper value to aid in preventing salt from entering the machine systems.

6. Operation in Humid Climate a. In climates with high humidity, thoroughly wash the machine daily and coat all bare surfaces with an oil based lubricant to help prevent corrosion.

3-44

4. MAINTENANCE

4. MAINTENANCE

4

4-1

4. MAINTENANCE

4-2

4. MAINTENANCE

4.1

GENERAL INFORMATION

Read, understand and follow all safety precautions contained in this manual before performing any inspection or maintenance procedures on this machine, it's systems or components.

For the adjustment, disassembling and repair of the engine, reduction gear and electronic equipment (controller, etc.), contact the dealer/distributor.

A. It is recommended, that an inspection and maintenance schedule be developed and maintained on a regular basis for this machine. Developing and maintaining such a schedule helps to keep the machine in optimum operating condition.

B. The information contained in this section gives the proper procedures for performing inspection and maintenance functions for this machine. Use these procedures when performing inspection and maintenance as they will guide the technician step by step for each procedure. Also, refer to the inspection and maintenance charts for general service interval recommendations.

4 C. Lubrication and maintenance intervals are determined by the hour meter. If performing lubrication and maintenance according to calendar time is preferred, the hour meter reading must correspond to the lubrication and maintenance period (8H, 50H, 120H, 250H, 500H, 1000H, 2000H, 5000H etc.) in calendar time; then calendar time can be used. Items for which service time cannot be specified are explained in the section WHEN REQUIRED.

The inspection and maintenance charts provided in this section give only general time intervals. It may be necessary to develop a custom schedule to perform machine maintenance at more frequent intervals based on the work conditions such as severe applications, work in dusty or humid circumstances, etc.

See "4.9 INSPECTION & MAINTENANCE CHART".

4-3

4. MAINTENANCE D. Use only specified oils, fluids, lubricants, filters and replacement parts to keep machine in optimum operating condition. Use the oils and greases with the specified viscosity depending on the ambient temperature.

Store containers of oils, fluids and grease indoors in appropriate location. This will prevent contamination from dust, water, etc.

4-4

4. MAINTENANCE

4.2

GENERAL SAFETY & PRECAUTIONS

-Do not attempt any other inspection or maintenance procedures other than those specified in the manual.

Carry them out parking the machine at a flat and conveniently situated place.

-Do not attempt any MAINTENANCE with engine running. Stop the engine and allow machine to cool to avoid injury.

A. WEAR SAFETY EQUIPMENT TO AVOID INJURY

Wear hard hat, safety goggles or face shield, work gloves, safety shoes and well fitting work clothes when performing inspection and maintenance procedures on this machine.

B. KEEP MACHINE CLEAN Thoroughly clean machine before performing inspection and maintenance procedures. It is easier and safer to locate problems, perform maintenance and also reduce the risk of hydraulic system contamination when machine is clean.

C. CONFIRMATION FOR HOUR-METER Read the hour-meter daily, and check with the scheduled maintenance book. See "4.9 INSPECTION & MAINTENANCE CHART" for better reference. Proceed with any maintenance as required.

4-5

4

4. MAINTENANCE D. STOP ENGINE

Do not attempt any MAINTENANCE with engine running.

Always stop the engine and allow machine to cool to avoid injury.

Otherwise, there is a possibility of danger that your hand may be caught in the cooling fan or fan belt resulting injury.

If it is unavoidable to operate the engine for inspection or maintenance, carry out the work with two people. The person seated in the operator's seat should be ready to stop the engine at any time while watching for a signal from the other person.

E. TAG-OUT MACHINE Before beginning any inspection or maintenance procedures, secure a "DO NOT OPERATE" tag (P/N: YN20T01320P1) to the operator's console to inform the operator that the machine will be inoperable for inspection and maintenance. This tag will help prevent accidental starting of the machine.

F.

OBSERVE PRECAUTIONS

Start the inspection and maintenance work fully understanding the contents of safety precautions indicated on the machine labels.

PV20T01005P1

G. HOT SURFACES & FLUIDS

Wear the proper safety equipment when working around hot areas. Do not change oils, engine coolant or filters immediately after machine has been stopped. Allow machine to cool down before performing maintenance procedures.

4-6

4. MAINTENANCE H. WARM ENGINE OIL Engine oil should have a temperature of between 20 to 40C degrees {68 to 104 F degrees} before the oil is changed.

If necessary run engine until the oil is warm within the recommended oil change temperature.

I.

PRESSURIZED SYSTEM HAZARDS

Release the internal pressure before removing the hydraulic system or fuel system, piping or coupling of the cooling system or other related parts to which internal pressure is applied.

See "4.2.S HYDRAULIC TANK PRESSURE" to release internal pressure.

J.

PREVENT CONTAMINATION

Always cap or plug lines when hydraulic components are removed to help prevent hydraulic system contamination that can be caused by dirt, dust and debris entering a line or port.

Do not allow hydraulic line or component to become contaminated. This could cause severe system damage.

Contact an authorized dealer/distributor to obtain the proper caps and plugs to be used on this machine.

K. INSPECT WASTE OILS AND FILTERS Before disposal, inspect all waste oils, fluids and filters for debris and foreign matter.

It is recommended to cut open the oil filters to determine any abnormal wear.

L. CAUTION FOR OIL FILLING When a strainer is provided on the filling port, do not remove it while refilling fuel, oil or fluid.

4-7

4

4. MAINTENANCE M. DISPOSAL OF HAZARDOUS WASTE Dispose of waste oils, fluids, lubricants, filters and other hazardous waste properly.

CONTAMINATION HAZARDS Dispose of all hazardous waste in accordance with government environmental laws and regulations.

N. SEALS AND O-RINGS After removing the O-ring or gasket, clean the seal surface, and replace with a new one.

Always replace seals and O-rings with new parts.

Never reuse a seal or O-ring during reassembly of components. Lubricate all new seals with the appropriate oil before installation.

O. USE SUPPORT EQUIPMENT DURING SERVICE When machine inspection or maintenance is done under the boom, arm or under the bucket/attachment use proper equipments or blocks to secure the attachment.

P.

CAUTION WHILE CHANGING BUCKET/ATTACHMENT

Do not insert your finger, hand or arm into the pin bore.

The alignment must be carried out visually or by using a tool.

4-8

4. MAINTENANCE Q. OPERATION IN DUSTY CONDITIONS When the machine is operated in dusty operating conditions, do the following.

•

• • •

Frequently check the lamp for the air cleaner clogging.

Clean the air cleaner element ahead of the specified period.

Clean the radiator core ahead of the specified period to prevent it from clogging.

Clean and replace the fuel filter element ahead of the specified period.

Clean the electric equipment, especially starter and generator, to not allow deposit of dust on them.

5

R. CLEANING PARTS Use only approved cleaning solvents and proper equipment to clean parts.

Do not use gasoline, diesel fuel or other flammable solvents to clean parts.

Clean parts in a well ventilated area.

S. HYDRAULIC TANK PRESSURE Always release the internal pressure of the hydraulic tank before performing inspection or maintenance procedures.

1. Remove cap (A) and push "DOWN" valve (B) to release air pressure in the reservoir.

A

4 B

Gasses from hydraulic tank may be hot.

Wear safety equipment to avoid injury.

4-9

4. MAINTENANCE T.

WELDING SAFETY

1. Turn starter key switch to "OFF" position. Wait 4 seconds for electrical power to disconnect.

2. Remove negative (-) cable from battery terminal.

3. Attach welder ground cable with 1 m {3'3"} away from component being welded.

4. Make sure welder ground is not located at a seal or bearing. Do not locate welder ground at seal or bearing.

5. Make sure that no bearings or seals separates the welder ground and the weld area.

U. PRECAUTION AGAINST MACHINE WASHING When washing the machine, do not use high pressure water to wash the inside of car body (swivel joint area).

4-10

4. MAINTENANCE

4.3

LUBRICANT, FUEL & COOLANT SPECIFICATIONS

The following chart provides information on the specification of oils, grease, fuels and coolant to be used in various climates and working conditions.

Komponent

Hydraulikkoljetank

Motoroljepannen

Type av Kapasitet (under smøremiddel utskifting)

Hydraulikkolje

Motorolje JASO DH-1

Rotasjonsmotorreduktor Kjøremotorreduktor

Girolje

Rotasjonsmotorreduktor (Hus) Festepinner Svingbart kronhjul Justering av beltespenning

EP-smørefett

Manøvreringsspak (Styreventil) Svinggir

-22 -30

-4 -20

48 Liter (13 Gal) 90 Liter (24 Gal) Hydraulic system

1.35 Liter X 2 (0.4 Gal X 2)

Klimasone 32 0

50 10

68 20

86 30

ISO VG46

[Totalvolum] 11 Liters (2.9 Gal) [H level] 10.3 Liters (2.7 Gal) [L nivå] 7.3 Liters (1.9 Gal)

1.5 Liter (0.4 Gal)

14 -10

104 F Spesifisert smøremid 40 C (KOBELCO BRAND) Hydraulisk olje med lan holdbarhet KW5046 (20 P/No. KAP2421R157D9

ISO VG32

(KOBELCO BRAND) Long life hydraulic oil KW5032S (20 L) P/No. KAP2421R157D7

SAE 10W-30

(KOBELCO BRAND) JASODH-1 P/No. KAPYN01T01053D1 (20 L)

SAE 15W-40

OLJE FOR VEKSLER SAE #90

150 g (0.3 lbs)

EP GREASE

17 plass

EP GREASE

1 plass

EP GREASE

2 plass

EP GREASE

Etter behov

EP GREASE

4.9 kg (10.8 lbs)

EP GREASE ASTM D-975 No.2

Drivstofftank

Dieseldrivstoff

120 Liter (32 Gal)

ASTM D-975 No.2 ASTM D-975 No.1

Radiator (Reservetank)

5.7 L Motorkjølevæske totalvolum (Frostvæske)

50% blanding

8.5 L

SAE 15W-40 (KOBELCO BRAND) A.P.I klassifisering for "service GL-4" Delnr. KAPSPG90020

(KOBELCO BRAND) Flerbruks smørefett, ekstremt trykk, nr.2*2

ASTM D-975 Klasse 2-D ASTM D-975 Klasse 1-D (KOBELCO BRAND) Hvis du bruker kjølevæske som kjøpes separat, skal blandingsgraden tilsvare den spesifisert .*1

P/No. KAPLLC95-20 (20 L)

4-11

4

4. MAINTENANCE

Handling method of long life hydraulic oil When changing and replenishing hydraulic oil, make sure to use oil specified by US. The use of unspecified hydraulic oil or the use of mixed oil causes deterioration of oil resulting in shortening life of oil.

The above hydraulic oil change time is 5,000 hours.

Specified oil : Maker : Shell Brands : Shell Tellus Oil S46 Shell Tellus Oil ST32 Be sure to select hydraulic oil adaptable to the ambient temperature.

-When the oil leak and damage are found in the lower roller, upper roller and front idler, contact our dealer/ distributor for repair.

-Use ASTM D-975 No.2 oil for fuel without fail.

This engine is equipped with electric control high pressure fuel injection system to obtain the features like excellent fuel saving and emission in good condition. This system requires the parts in high precision and high lubricating ability. Therefore if low viscosity fuel in low lubricating ability is used, the durability may be notably lowered.

AVOID ANTIFREEZE / COOLANT FIRE HAZARD Antifreeze/Coolant is flammable. Direct contact with hot surfaces of flames may cause the Antifreeze/Coolant to burn. Repair leaks immediately and dispose of used Antifreeze/Coolant promptly and in accordance with government environmental regulation.

*1 : L.L.C means "Long Life Coolant" *2 : Cartridge part number KAPG0420D1 (400 g × 20). Pail can part number KAPG1601D1.

LLC [OUR GENUINE ANTIFREEZE / COOLANT] The cooling system is filled long life coolant LLC which is our Genuine Antifreeze / Coolant specified by us for this machine. Our Genuine Antifreeze / Coolant protects the cooling system from harmful corrosives while providing superior cooling performance necessary for emissions compliant engines for up to 2 years or 2000 hours of operation. Our Genuine Antifreeze / Coolant also protects the engine from freezing in cold climate regions. Use of coolant other than our Genuine Antifreeze / Coolant is not recommended and may result in poor machine performance and possible damage to the engine and cooling system. Our Genuine Antifreeze / Coolant is specified for all machines operating in all regions including areas where cold temperatures or freezing is not normally expected.

4-12

4. MAINTENANCE

4.4

USE OF BIO-DEGRADABLE OILS

When using Bio-degradable Oil (BIO OIL), refer to the following information.

A. Recommended Oil Maker

Mobil

Brand

MOBIL EAL Envirosyn 46H

B. Precaution for the Use of Oil 1. When filling the former machine in which mineral oil is charged with BIO oil, try to flush the machine three times.

The mineral oil will be left in the circuit of the machine without flushing, resulting in the reduction of effect of biodegradation ability.

2. When you use BIO OIL, slewing and travel parking brake performance will be reduced because of lower friction factor of BIO OIL compared to that of mineral oil.

C. Flushing Procedure 1. Drain mineral oil from the hydraulic tank completely.

2. Drain mineral oil from the cylinder completely.

3. Fill hydraulic oil tank with new BIO oil.

4. After starting engine, move every cylinder 10 strokes respectively.

The abrupt operation may cause burning of seal because of trapped air in the cylinder.

Try to operate first 4 strokes slowly at engine low idling to charge hydraulic oil in the entire cylinder.

5. Idle travel motor right and left for about 3 minutes.

6. Repeat swing operation 10 rotations.

7. Drain BIO oil from hydraulic tank completely.

8. Drain BIO oil from each cylinder completely.

9. Fill hydraulic tank with new BIO oil. Similarly, repeat the procedure 4. to 9. two times.

10. For hydraulic oil in final condition, analyze the hydraulic oil and be sure of amount of remaining mineral oil.

D. Bio Oil Change Interval The BIO oil change interval is 2,000 hours.

For the changing procedure, refer to the section "4.19.A Change Hydraulic Oil".

4-13

4

4. MAINTENANCE

4.5

MAINTENANCE PARTS

A. Filters & Elements, and Bucket Replace parts, such as filters and elements, during the periodical maintenance or before the service life.

The machine can be used economically if the parts are changed properly and timely.

When you place an order of parts, confirm the parts number on parts manual.

System

Hydraulic oil tank

Part Number

Parts Name

Q'ty

Replacement Interval

YR52V01004R400

Return filter element kit (STD. Breaker)

1

(ZD11G11000)

(O-ring)

1

YT50V00003F1

Suction strainer

1

(ZD11G15500)

(O-ring)

1

YT11P00009S002

Element (Outer)

1

After 6 times of cleaning or one year whichever comes first

After 50 hours (first change) Every 1000 hours (from 2nd change) (Breaker specification : Every 250 hours) Every 2000 hours

YW11P01021P1

Element (Inner)

1

For machines equipped with W (double) element the inner element must be replaced together with the outer element.

Replace the inner element with new one.

Engine oil filter

VI898075-6760

Cartridge

1

After 50 hours (first change)Every 500 hours

Fuel pre-filter

YT21P01006R100

Element kit

1

Every 500 hours

Fuel filter

VI897172-5491

Cartridge

1

Every 500 hours

Electromagnetic pump

VI894337-0220

Repair kit

YN50V01015P3

Air-con filter (Outer)

1

YN50V01014P1

Air-con filter (Inner)

1

Every 10 times cleanings When heavy clogging of filter occurs, clean or replace

YN50V00020F1

Line filter

1

Every 2000 hours (Cleaning)

2412N279D1

Side cutter (R, H)

1

2412N279D2

Side cutter (L, H)

1

ZS13C20050

Bolt

6

ZN13C20016

Nut

6

B12P0015F1

Tooth Assy (Inner)

2

2412U111F1

Tooth Assy (Outer)

2

Air cleaner

Air conditioner Pilot line filter

Bucket (STD)

Every 500 hours change

Items enclosed in parenthesis ( ) are the parts to be changed at the same time.

4-14

When required

4. MAINTENANCE

4.6

TORQUE VALUES FOR SPECIFIED

Follow the table below and tighten or retighten every bolt and nut. Check for any loose or missing bolts or nuts before daily operation and during periodical inspections. Retighten or supply new parts for missing ones as required.

Størrelse Antall (M) M5

• Sendeenhetsmontering (drivstofftank)

• 1.96±0.2 {1.4±0.14}

4

10

• A/C kondensormontering

• 9.7±1.0 {7.2±0.7}

4

10

• Montering undertank for vann

• 9.6±1.0 {7.1±0.7}

413

•Lyddemperfeste (Øvre mutter)

•10.8±1.9 {8.0±1.4}

M8413

•Lyddemperfeste (Nedre mutter)

•8.8±0.8 {6.5±0.6}

• Luftrenserfeste

• 19.6±2.0 {14.5±2.1}

13

310

M12

M14

M16

M20 5/818UNF

Tiltrekkingsmoment N•m {lbf•ft}

–

2

M10

Posisjon

5

M6

Motsatte flater mm

•Inspeksjonsdekselmontering for svingsmøringsbad •19.6 {4.5}Apply

Anbefalt tetningsmiddel

Påfør Loctite nr. 262 Loctite #242

16

17

• Gummifeste for gulvplate

• 46.5±4.6 {34±3.4}

8

17

•Monteringsbrakett for drivlager

•64.7±6.4 {47±4.3}

12

17

•Feste for hydraulisk oljetankdeksel

•46.5±4.6 {34±3.4}

2

17

•Feste for nedre rammes smøringsdeksel

•10.8±0.98 {8.0±0.7}

6

17

•Montering av drivstofftankens bunndeksel

•46.5±4.6 {34±3.4}

4

17

•Monteringsbrakett for maskinens lyddemper

•64.7±6.5 {47±4.8}

Påfør Loctite nr. 262

10

17

•Motormontering

•46.5±4.6 {34±3.4}

Påfør Loctite nr. 26

4

19

•Motormontering

•80±8 {59±5.9}

Påfør Loctite nr. 27

4

19

•Radiatormontering

•120.6±12 {89±8.8}

Påfør Loctite nr. 26

2

19

• Montering radiatorstag

• 120.6±12 {89±8.8}

6

19

•Førerhusmontering

•80±8 {59±5.9} • 67±6.7 {49±4.9}

Påfør Loctite nr. 262

4

10

• Hydraulikkpumpemontering

3

19

• Svingleddfeste

• 107.8±10.8 {79.5±8.0}

Påfør Loctite nr. 262

4

19

•Mellomhjul og justeringsbolt for mellomhjul

•115±12 {85±8.8}

Påfør Loctite nr. 26

8

19

•Feste for kjøremotordeksel

•83.4±8.4 {62±6.2}

Påfør Loctite nr. 262

24

22

•Tannhjulsmontering

•181±18 {134±13}

Påfør Loctite nr. 26

40

22

•Nedre rullemontering

•181±20 {134±15}

Påfør Loctite nr. 262

156

22

•Montering av skobolt

•294±29 {217±21}

14

22

•Veiledning montering

•181±18 {133±13}

4

24

•Monteringsmutter for gulvplate av gummi

•191±19 {141±14}

4

24

•Hydraulikktankmontering

•191±19 {141±14}

Påfør Loctite nr. 262

2

24

•Øvre rullemontering

•279±29 {206±20}

Påfør Loctite nr. 26

24

24

•Kjøremotormontering

•279±28 {206±20}

Påfør Loctite nr. 26

24

24

•Ytre montering for svinglager

•157±16 {116±12}

Påfør Loctite nr. 262

30

24

•Indre spormontering for svinglager

•279±28 {206±20}

Påfør Loctite nr. 262

4

24

•Drivstofftankmontering

•191±19 {141±14}

Påfør Loctite nr. 26

8

24

•Svingreduksjonsenhetsmontering

•279±29 {206±21}

Påfør Loctite nr. 26

6

30

•Sidekuttermontering

3

30

•Motvektmontering

•490±48 {362±35}

2

19

•Smørenippelmontering for rullejustring

•59±10 {44±7.4}

Påfør Loctite nr. 26

•539±54 {398±40}

4-15

Påfør Loctite nr. 26

4

4. MAINTENANCE

The counterweight attaching bolts may be loosened by hitting the counterweight against solid obstructions during swing operation.

How to check: Strike the bolt head or nut by hand hammer lightly and find the looseness by catching dull sound. Tighten bolts and nuts again if necessary.

4-16

4. MAINTENANCE

4.7

TORQUE SPECIFICATIONS FOR BOLTS & NUTS

The following torque specifications are provided for use when actual torque value of a fastener is not known.

Check the machine for loose bolts and nuts daily before starting work and at the scheduled maintenance interval. Replace missing bolts and nuts with equal specification as the original parts. Contact the dealer/distributor for assistance if necessary. Tighten loose and replacement nuts and bolts to the specification given in the specific manual section or in the chart below.

Refer to the below table for proper tightening of bolts.

A P M

-The torque values in the table do not apply for all bolts used with plastic covers. For the tightening torque for such bolts, consult with dealer/distributor. Over-tightening may cause for damage on the parts to be fixed.

-Check if the torque is specified in a specific section of this manual. If provided, use the torque in the specific section.

-Metric hardware with thread size diameter of M5 or greater have a number on the top of the bolt indicating the strength of the bolt.

4

4-17

4. MAINTENANCE 1. Metric coarse thread standard tightening torque values. Tighten all bolts and nuts to proper torque values.

Metrisk grovgjenget (Ikke belagt) Tiltrekningsverdi Enhet: N•m {lbf•ft} Klassifisering Nominell størrelse

4.8T Ingen smøring Oljesmøring

7T

10.9T

Ingen smøring Oljesmøring Ingen smøring Oljesmøring

M6

P=1

4.4±0.5 {3.2±0.4}

3.7±0.4 {2.7±0.3}

9.6±1.0 {7.1±0.7}

8.1±0.8 {6.0±0.6}

17.4±1.8 {12.8±1.3}

14.7±1.5 {10.8±1.1}

M8

P=1.25

10.7±1.1 {7.9±0.8}

9.0±0.9 {6.6±0.7}

23.5±2.0 {17.3±1.5}

19.6±2.0 {14.5±1.5}

42.2±3.9 {31.1±2.9}

35.3±3.9 {26.0±2.9}

M10

P=1.5

21.6±2.0 {15.9±1.4}

17.9±1.8 {13.2±1.3}

46.1±4.9 {34.0±3.6}

39.2±3.9 {28.9±2.9}

83.4±8.8 {61.5±6.5}

70.6±6.9 {52.1±5.1}

M12

P=1.75

36.3±3.9 {26.8±2.9}

31.4±2.9 {23.2±2.1}

79.4±7.8 {58.6±5.8}

66.7±6.9 {49.2±5.1}

143±15 {105±11}

121±12 {89.2±8.9}

M14

P=2

57.9±5.9 {42.7±4.4}

49.0±4.9 {36.1±3.6}

126±13 {92.9±9.6}

106±10 {78.2±7.4}

226±20 {167±15}

191±19 {141±14}

M16

P=2

88.3±8.8 {65.1±6.5}

74.5±6.9 {55.0±5.1}

191±20 {141±15}

161±16 {119±12}

343±39 {253±29}

284±29 {209±21}

M18

P=2.5

122±12 {90.0±8.9}

103±10 {75.8±7.2}

265±29 {195±21}

226±20 {167±15}

481±49 {355±36}

402±39 {297±29}

M20

P=2.5

172±17 {127±13}

144±14 {106±10}

373±39 {275±29}

314±29 {232±21}

667±69 {492±51}

559±59 {412±44}

M22

P=2.5

226±20 {167±15}

192±20 {142±15}

500±49 {369±36}

422±39 {311±29}

902±88 {665±65}

755±78 {557±58}

M24

P=3

294±29 {217±21}

235±29 {173±21}

637±69 {470±51}

520±49 {383±36}

1160±118 {856±87}

941±98 {694±72}

M27

P=3

431±39 {318±29}

353±39 {260±29}

941±98 {694±72}

765±78 {564±58}

1700±167 {1250±123}

1370±137 {1010±101}

M30

P=3.5

588±59 {434±44}

490±49 {361±36}

1285±127 {948±94}

1079±108 {796±80}

2300±235 {1700±173}

1940±196 {1430±145}

M33

P=3.5

794±78 {586±58}

667±69 {492±51}

1726±177 {1270±131}

1451±147 {1070±108}

3110±314 {2290±232}

2610±265 {1930±195}

M36

P=4

1030±98 {760±72}

863±88 {637±65}

2226±226 {1640±167}

1863±186 {1370±137}

4010±402 {2960±297}

3360±333 {2480±246}

4-18

4. MAINTENANCE 2. Metric fine thread standard tightening torque values. Tighten all bolts and nuts to proper torque values.

Metrisk fingjenget (Ikke belagt) Tiltrekningsverdi Enhet: N•m {lbf•ft} Klassifisering Nominell størrelse

4.8T 7T Ingen smøring Oljesmøring Ingen smøring Oljesmøring

10.9T Ingen smøring Oljesmøring

M8

P=1.0

11.3±1.1 {8.3±0.8}

9.5±1.0 {7.0±0.7}

24.5±2.0 {18.1±1.5}

20.6±2.0 {15.2±1.5}

44.1±3.9 {32.5±2.9}

37.3±3.9 {27.5±2.9}

M10

P=1.25

22.6±2.0 {16.7±1.5}

18.7±1.9 {13.8±1.4}

48.1±4.9 {35.5±3.6}

41.2±3.9 {30.3±2.9}

87.3±8.8 {64.4±6.5}

73.5±6.9 {54.2±5.1}

M12

P=1.25

39.2±3.9 {28.9±2.9}

33.3±2.9 {24.6±2.1}

85.3±8.8 {62.9±6.5}

71.6±6.9 {52.8±5.1}

154±16 {114±12}

129±13 {95.2±9.6}

M16

P=1.5

92.2±8.8 {68.0±6.5}

77.5±7.8 {57.2±5.8}

196±20 {145±15}

169±17 {125±13}

363±39 {268±29}

304±29 {224±21}

M20

P=1.5

186±19 {137±14}

155±16 {114±12}

402±39 {297±29}

333±29 {246±21}

726±69 {535±51}

608±59 {448±44}

M24

P=2

314±29 {232±21}

265±29 {195±21}

686±69 {506±51}

569±59 {420±44}

1240±118 {915±87}

1030±98 {760±72}

M30

P=2

637±59 {470±44}

530±49 {391±36}

1390±137 {1030±101}

1157±118 {853±87}

2500±255 {1840±188}

2080±206 {1530±152}

M33

P=2

853±88 {629±65}

706±70 {521±52}

1860±186 {1370±137}

1550±155 {1140±114}

3350±334 {2470±246}

2790±275 {2060±203}

M36

P=3

1070±108 {789±80}

892±88 {658±65}

2330±226 {1720±167}

1940±196 {1430±145}

4200±422 {3100±311}

3500±353 {2580±260}

4

4-19

4. MAINTENANCE

4.8

TORQUE SPECIFICATIONS FOR JOINTS & HYDRAULIC HOSES

A. Ors Joint (O-Ring Sealing Type)

Nominell størrelse

Nøkkelstørrelse (mm) 30

1–14 UNS

Slangemunnstykke og kobling

Tiltrekningsverdi Enhet: N•m {lbf•ft}

36

177±18 {130±13}

41

206±21 {152±15}

41

1–7/16–12 UN

Nippe

137±14 {101±10}

32

1–3/16–12 UN

Konnektor O-ring

206±21 {152±15}

46

Mutter

B. Nuts & Sleeve

Strammingsverdi N•m {lbf•ft}

10 × 1.5

19

49±9.8 {36±7}

15 × 2.0

27

118±12 {87±9}

18 × 2.5

32

147±15 {108±11}

22 × 3.0

36

216±22 {159±16}

28 × 4.0

41

275±27 {202±20}

35 × 5.0

55

441±44 {325±33}

Muffe

B

Mutter O.D. ( )

Nøkkelstørrelse B (mm)

O.D. ( )

Rørstørrelse O.D. × tykkelse (mm)

C. Joints for Piping

Nominell skruestørrelse (PF)

Nøkkelstørrelse (mm)

Strammingsverdi N•m {lbf•ft}

1/8

14

15±2 {11±1.5}

1/4

19

36±2 {27±1.5}

3/8

22

74±5 {54±4}

1/2

27

108±9.8 {80±7}

3/4

36

162±9.8 {119±7}

1

41

255±9.8 {188±7}

1–1/4

50

392±40 {289±30}

1–1/2

55

485±49 {358±36}

O-ring

D. Hydraulic Hoses

Nominell skruestørrelse (PF)

Nøkkelstørrelse (mm)

Strammingsverdi N•m {lbf•ft}

1/8

14

15±2.0 {11±1}

1/4

19

29±4.9 {22±4}

3/8

22

49±4.9 {36±4}

1/2

27

78±4.9 {58±4}

3/4

36

118±9.8 {87±7}

1

41

137±15 {101±11}

1–1/4

50

167±15 {123±11}

4-20

Konnektor

O-ring

Konnektor

Nippel

4. MAINTENANCE E. Split Flange

Arbeidstrykk Size

MPa {kgf/cm 2} 20.6 {210}

Strammingsverdi N•m {lbf•ft}

Boltstørrelse (M)

Arbeidstrykk

MPa {kgf/cm2} 41.2 {420}

Strammingsverdi N•m {lbf•ft}

Boltstørrelse (M)

3/4

33.9±5.6 {25±4.1}

10

39.5±5.6 {29±4.1}

10

1

42.4±5.6 {31±4.1}

10 62.2±5.6

{46±4.1}

12

1–1/4

55.1±7.1 {41±5.2}

10

1–1/2

70.6±8.4 {52±6.2}

12

169±11 {125±8.1}

16

2

81.9±8.4 {60±6.2}

12

282±11 {208±8.1}

20

93.3±8.4 {69±6.2}

These tightening torques are available in the case of tightening without lubricant.

4-21

14

4

4. MAINTENANCE

4.9

INSPECTION & MAINTENANCE CHART

Follow the chart below for recommended intervals of regular inspection and maintenance procedures. Perform inspection and maintenance according to the calendar time or operation time shown by the hour meter, whichever comes first.

See the inspection and maintenance procedure mentioned below for details.

Symbols and their meanings : : Necessary regular inspection item to hour meter : Only first replacing is performed : Inspection and/or maintenance is needed

System

See "4.3 LUBRICANT, FUEL & COOLANT SPECIFICATIONS" for detail specification for lubricant, coolant, fuel and etc.

LLC: Our genuine antifreeze/coolant.

Systemet Vedlikehold å utføre

Motorolje

Kontroller oljenivået

Hvis nødvendig

Intervall (timer på timeteller) 8H

50H

100H

250H

500H

1,000H

2,000H

Smøremiddel etc. RE 5,000H (Utskiftingsdel) EN

3

O Motorolje

*1

Skift ut

4

O

(Første)

*1

Skifte av oljefilter

O

Patron

4

O

Patron

4

(Første)

Drivstoffilter Drivstoffets forfilter

Skift ut Drain

O

Skift ut

O

Skifte filter på elektromagnetisk pumpe

Motor

Når varsel vises på multidisplayet eller hver 250 timer.

Kontroller nivået

Etter 6 ganger med rengjøring eller et år, hva som kommer først

4 4

Ytre, indre element

O

3

O O

Kontroller/ rengjør

(eller hvert 2. år)

Slanger i kjølesystemet Kontroll og rengjøring av radiator/ oljekjølerkjerne/luftkjøler og filter

3

Ytre element (Når det ytre elementet skiftes ut må også det indre elementet skiftes ut) 4

O

Skift ut

Kjølevæskenivå og rengjøring av kjølesystemet

Filter

O

Kontroller/ rengjør Luftfilterelementer

Element

O O

O

4-22

LLC

4 4 3 4

4. MAINTENANCE

System

When the machine works at dusty site, clean the filter and the core of radiator often. Clean the filter and core depending on their dirt.

Vedlikehold å utføre

Kontroller beltespenning Radiatorlokk

Kontroll Juster dem Rengjøring

Hvis nødvendig

Intervall (timer på timeteller) 8H

50H

100H

250H

500H

4.

O

4.

O *1

O

4.

(Første)

O

*2 Kontroll og justering av kompresjonstrykket

O

*2 Kontroll av inntak og eksosmanifold for stramming

*1

O

(Første)

*2 Kontroll av bunnpanne og annet tilleggsutstyr for stramming

*1

O

(Første)

*2 Kontroll av installert turbolader for stramming

*1

O

(Første)

*2 Kontroll av turboladerrotor og kompressorhjul for rotering

O

*2 Kontroll av turboladerrotor for løse deler

O O

O

*2 Kontroll og rengjøring av statorbørste og strømfordeler

O

*2 Kontroll av bunnpanne for å se om vann og drivstoff kommer inn

O

*2 Kontroll av viftens monteringsbolt for stramming

O

*2 Kontrollere om termostatet fungerer

O

*2 Kontrollere om starteren fungerer

O

*2 Kontrollere stabilitet, eksosfarge og støy

Smøremiddel etc. RE 5,000H (Utskiftingsdel) EN

4.

O

Kontroll av motormonteringsbraketten for stramming *2 Kontroll og justering av ventilklaringen

*2 Kontroll av turbolader for smøring

2,000H

3.

O

Kontroll av innsugingssystemets gummislange

Motor

1,000H

O

*2 Kontrollere varmeapparatets plugg/inntak for luftvarmer (starthjelp)

O

*2 Kontrollere om vekselstrømsdynamoen fungerer

O

*2 Kontrollere hver rørskjøt for stramming

*1

O

(Første)

*2 Kontroll av eksosrør og lyddemper for løshet og skade

*1 (Første)

4-23

O

4

4. MAINTENANCE

Motor

System

-Contact our dealer/distributor for checking and adjustment shown by asterisk *2.

-*1-Break-in (After first 50, 100, 250, 500 Hours) Inspection & Maintenance Required.

Hvis nødvendig

Vedlikehold å utføre

*2 Kontroll og rengjøring av vekselstrømsdynamobørsten (hvis utstyrt med dette) Kontroller for lekkasje fra drivstoffsystemet

Drivstoffsystem

50H

100H

250H

Kontroller for motoroljelekkasje Kontroller motorens elektriske koblinger

Hydraulikkolje Hydraulikktank

Smøremiddel etc. REF. 5,000H (Utskiftingsdel) ENHETER

—

O

—

O

—

O

3.1.2.C 4.12.B

O

4.16.I

O

4.16.D

O

3.1.2.F

O Hydraulikkolje

O Skift ut

1,000H (Hydraulikkhammer)

OppsugRengjøring sfilter

4.19.A

O

O

Filter

4.18.D

Element

4.17.A

O *1

Returfilter

O

(Hydraulikkhammer)

(Første)

Kontroller for oljelekkasjer

O

3.1.1.A

Kontroller slanger / ledninger

O

3.1.1.A

Stryreventilfilter Kontroller dreiereduktorens oljenivå og fyll på

Rengjøring

4.18.F

O

Kontroller oljenivået

O

Girolje for 4.14.A ekstremt trykk

(120hr)

*1

Skift ut

O

(Første)

Smør styrering

Øvre struktur

2,000H

—

Drivstofftank Rengjør lokk og filter

Kontroller oljenivået

1,000H

O

Tøm vann og deponeringer

Tappeluft fra drivstoffsystemet

500H

O

Kontroll/drivstoffsnivå

Hydraulisk system

Intervall (timer på timeteller) 8H

SAE #90 GL-4

4.18.B

EP-smørefett 4.16.J

O

Kontroller styrering og planethjul

O

4.18.E

Skift smøring for styreringens smørebad

O

EP-smørefett 4.18.E

Kontroller svingbremsen

—

O

Smøring av kontrollspak, ventilstøtestang og universalledd

O

EP-smørefett 4.16.G

Kontroller bolter/vridningsmoment (styrering)

O

4.16.F

Kontroller bolter/vridningsmoment (motvekt)

*1

4-14

O

(Første)

*1

Smør svingreduseren

(First)

4-24

O

4.17.C

System

4. MAINTENANCE Hvis nødvendig

Vedlikehold å utføre

Intervall (timer på timeteller) 8H

50H

Kontroller oljenivået

Kontroller kjørereduktorens oljenivå og fyll på

100H

250H

500H

1,000H

2,000H

Smøremiddel etc. REF. 5,000H (Utskiftingsdel) ENHETER

O

Girolje for 4.14.B ekstremt trykk

(120hr)

*1

Skift ut

O

(First)

smøringsdeksel

Justere beltespenning

4.12.C

O

3.1.1.A

Kontroller ledninger for skade

O

3.1.1.A

Kontroller trinn og håndløpere

O

3.1.1.A

Kontroller rammestrukturen

O

3.1.1.A

Kontrollere belter og ledd

O

3.1.1.A

Kontroller kjededrevet for slitasje

O

3.1.1.A

Kontroller mellomhjulet for slitasje

O

3.1.1.A

Kontroller rullen for slitasje

O

3.1.1.A

Kontroller beltespenning

O

3.1.1.A 4.15.I

O

4.13.A

O EP-smørefett

*3 O

Smøring av bulldozerskjær Tilbehør

4.18.C

Kontroller for oljelekkasjer

Smør grabbpinner

4.11.A

O

(50H)

Utskifting av graveskovl

O

4.10.D

Grabbklaring

O

4.10.G

Kontroller grabbtenner og sideskjær

O

4.10.E

Kontroll av bolter/vridningsmoment

Elektrisk

GL-4

O

Smørefett for tapper

Batteri

—

O

Batteri-elektrolytt

O

4.12.A

Battery maintenance

O

4.12.A

Spenningskontroll Inspiser alle ledninger

O

Kontroller brytere/lys

O

Kontroll og Luftkjølea- rengjøring av A/C kondensator nlegg Filter

3.1.1.A —

Kontroll av bolter/vridningsmoment Kontroll Sikkerhetsbelte

4.16.H

O O

4.15.H

O

Rengjøring

Skift ut Kontroller væskenivået for vindusviskeren Kontroller rammestrukturen

4.17.D

O

Kontroller A/C kjølevæske

Ekstrautstyr

SAE #90

O

4.15.F

Etter at rengjøring er utført 10 ganger

4.10.B

O O

3.1.1.A

O

4-14

O O

Skift ut

(3 years)

*3: Dozer blade has to be Lubricated every 8 hours for the first 50 hours of operation.

-After 50 hours of operation, dozer blade should be lubricated every 250 hours of operation.

4-25

2-46

4

4. MAINTENANCE

4.10

WHEN REQUIRED

Thoroughly read and understand the Section 1 "SAFETY PRECAUTIONS" of this MANUAL before operating or servicing the machine.

A. Cleaning or Replacement of Radiator Cap

To avoid being burned, be careful when removing the radiator cap. Coolant is under high pressure when hot.

-Do not remove the radiator cap when the system is hot.

-Allow enough time for the machine to cool down before removing the radiator cap.

A loose radiator cap will let hot steam and coolant escape from the cooling system. Allow the radiator cap/cooling system enough time to cool before tightening the loose cap.

1. After the radiator cap/cooling system has cooled so it can be touched with a bore hand, slowly loosen the cap (1) to release the pressure.

After all pressure is released, remove the radiator cap.

2. Check the cap for damage or contamination. Clean it and/or replace it if needed.

3. Securely tighten the cap.

B. Checking and Replacing Wiper Blade Check wiper blade for wear and damage, replace it if necessary.

4-26

1

4. MAINTENANCE C. Wind Washer Fluid Reservoir

The use of wiper without washer fluid discharged may cause damage to the motor equipped with the washer fluid reservoir.

Washer fluid reservoir (1) is located back of floor plate in cab.

1. Remove floor mat.

2. Check washer fluid level of washer fluid reservoir (1).

3. When washer fluid level was short, remove the cap and fill up the short of washer fluid.

4. Reinstall floor mat to the original position.

1

D. Replacement of Bucket

AVOID INJURY -Replace the bucket on firm level ground. Pay close attention to safety.

-The abrupt operation of front attachment is strictly prohibited because it may cause the danger.

-When aligning the pin bores, do not insert your finger into the bores. It may cause severe injury. Align the bores visually or by using a tool.

-Hold the removed bucket in the stable condition.

1

A: Bucket Boss

A

4-27

4

4. MAINTENANCE D.1 Removal of Bucket 1. Move the machine to a firm, level surface and rest the bucket on the ground, making certain the bucket is stable.

2. Roll O-rings (1) onto the bucket boss. After removing the pins, get them back to the original position.

3. Extend retaining ring (2), and remove pin (3) and pull pins (4), (5) out, and then remove bucket (6).

7 8

2,3

1 4

1 5

6

-Keep the pins free from any sand, dirt and other contaminants when removed.

-Do not damage the dust seals on both ends of arm (7) and bucket/bucket link (8).

D.2 Installing Bucket 1. Clean each pin and pin hole and grease sufficiently.

2. Move the bucket cylinder to match the pin bores or the 8 bucket (6) and bucket link (8) with each other, then 1 insert the pin (4).

4 3. Raise the boom and slightly raise the bucket from the ground.

4. Align bucket (6) with the pin hole of arm (7) moving arm (7), and insert pin (5).

6 5. Insert pin (3) and fix retaining ring (2).

6. Fit O-ring (1) to the normal position.

7. Apply grease on the grease nipples for respective pin until the grease comes out through the gap between pins and bore.

Replace the O-ring (1) if it is cracked or has lost elasticity, with a new one.

4-28

7 2,3

5

1 6

4. MAINTENANCE E. Check for Abrasion/Damages on Tooth Point & Side Cutter

When replacing the tooth point and side cutter, apply a safety block to the bottom face of the bucket.

Check for wear and looseness of the bucket tooth points.

Tooth point life cannot be determined only by the number of operating hour; operating conditions must also be considered.

A

A: Safety Block

1.

2.

3.

4.

5.

6.

7.

Adapter Nose Tooth Point Rubber Lock Locking Pin Side Cutter Bolt Nut

6

5 7

4-29

1 4 3 2

4

4. MAINTENANCE E.1 Replacing the Tooth Points

Wear, goggles, safety shoes, hard hat, work clothes and work gloves to perform inspection and maintenance on this machine.

Replace the bucket tooth in the following cases.

-When little holes appear on the tooth point.

-When the edge lines of the tooth point are worn.

1. Using a hammer and punching tool, hammer out the lock pin (4). Be careful not to damage the rubber lock (3).

2. Inspect the lock pin (4) and rubber lock (3).

Replace them if the lock pin (4) is too short or the rubber lock (3) is in poor condition.

3. Clean the surface of the adapter nose (1) with a putty knife to remove the adhered soil.

4. Fit the tooth point (2) onto the adapter nose (1).

5. Push the rubber lock pin (3) in the hole of the adapter nose (1).

6. Hammer the locking pin (4) until it is aligned with the point surface.

4-30

4. MAINTENANCE E.2 Replacing the Side Cutters

Wear, goggles, safety shoes, hard hat, work clothes and work gloves to perform inspection and maintenance on this machine.

1. Remove all sand and soil adhering around the bolts.

Use an acetylene torch to cut off the bolts, then remove the side cutter.

2. Clean the mounting face and install a new side cutter.

When replacing the side cutter, replace the bolts and nuts with new ones.

Tightening torque: 485 to 593 N-m {358 to 437 lbf-ft} 3. After tightening the nuts, spot-weld them.

A A: Safety Block

4 A

The delay in changing the side cutter from the specified interval may cause damage to bucket. Early replacement is recommended.

4-31

4. MAINTENANCE F. Reversing Backhoe Bucket The backhoe bucket which is reversed 180 degrees is available for shoveling work. When working in team, follow the signals exactly and pay particular attention to the safety.

1

1.

Move the machine to a firm level surface and place the bucket on the ground, making certain that the bucket is stable.

2.

Roll "O-rings" (1) onto the bucket bosses.

3.

Remove retaining ring and pin for bucket pin (2) and for link pin (3). And remove bucket pin (2) and link pin (3).

A: Bucket Boss

A

4.

3 Rotate arm 180 degrees with the arm slightly raised (B) and bucket in place, and lower the arm again and the pin bore position is changed.

5.

Clean pins for each part and pin bores and then apply grease sufficiently.

2 6.

Fit O-ring (1) in place 7.

B Align each pin bore, and insert pin. After inserting pin, fix the pin with retaining ring and pin.

8.

After attaching, rotate bucket softly to the stroke end in engine low idling condition and check that there is no interference of each section.

Be careful about the use of bucket for shoveling work because the bucket operation is reversed when compared to that for the work with backhoe.

4-32

4. MAINTENANCE G. Adjusting Bucket Mount Gap

-Unexpected movement of attachment, while adjusting the bucket mounting gap is quite dangerous. Place the bucket on the ground in a stable condition, and set the safety lock lever to "LOCKED" position, then stop the engine.

-If the clearance of the bucket is not properly adjusted, galling may occur on the contact faces of the bucket and arm, resulting in abnormal noise and damage of the shaft and O-ring.

Bucket Standard Clearance A: Bucket Clearance Adjusting Mechanism: 1.2 mm (0.05 inch) or less B: Bucket Boss 1. Place the bucket in stable condition on the ground.

2. Move O-ring (1) from the regular position to the bucket A boss position.

3. Swing rightward slightly and press the arm top end against the bucket right side. (On this side, there is not looseness adjustment mechanism.)

4. Move safety lock lever to "LOCKED" position and stop engine.

5. Measure clearance (A) between bucket and arm boss. In the event that the measured value is 1.2 mm or more, carry out the adjustment.

6. Three bolts (2) on the clearance adjustment section contain five shims (3) (1 mm in thickness) in average.

Loosen each bolt and eliminate sheets of shims equivalent to the clearance.

7. Tighten each bolt (2) to the specified torque equally.

Tightening torque: 103 to 127 N-m {76 to 94 lbf-ft} 8. Return O-ring (1) in place.

1

2

B

4-33

3

A

1

4

4. MAINTENANCE

4.11

PRE-START (EVERY 8 HOURS) INSPECTION & MAINTENANCE

Thoroughly read and understand the "1.SAFETY PRECAUTIONS" of this MANUAL before operating or servicing the machine. The following inspection and maintenance shall be carried out before starting/after starting and after work.

For the following checking and service items, refer to Chapter 3 "MACHINE OPERATION".

-3.1.1-A

Daily Inspection

-3.1.2-E

Check Radiator, Oil Cooler and Filter

-3.1.2-A

Checking Coolant Level for Shortage and Making UP

-3.1.2-F

Checking Hydraulic Oil Level

-3.1.2-B

Checking Oil Level of Engine Oil Pan and Making Up

-3.1.5

Checking Function of Gauge Cluster

-3.1.2-C

Checking Fuel Level and Making Up

-3.1.6

Checking Work Light

-3.1.2-D

Fuel Pre-Filter Drain

A. Lubrication for Dozer Blade Wipe all grease nipples and apply grease until the grease comes out through the gap of pin.

Grease gun is provided inside of side door on the left side of machine.

Greasing 1.

Dozer blade has to be lubricated every 8 hours for the first 50 hours of operation.

2.

After 50 hours of operation, dozer blade should be lubricated every 250 hours of operation.

3.

If attachment is sunk in water, it is recommended to lubricate it every 8 hours.

1. Dozer cylinder rod and head (1).

2. Dozer blade link pin (2).

1 2

2

1

4-34

4. MAINTENANCE

4.12

50 HOUR (WEEKLY) INSPECTION & MAINTENANCE PROCEDURES

Thoroughly read and understand the "1.SAFETY PRECAUTIONS" of this MANUAL before operating or servicing the machine.

Perform together with "4.11 PRE-START (EVERY 8 HOURS) INSPECTION & MAINTENANCE".

A. Batteries

-Wear hard hat, approved safety glasses or face shield, gloves and other safety equipment when working with batteries.

-Flammable gas (hydrogen gas) is generated in the battery. Do not allow sparks or flames to come in contact with batteries to avoid triggering an explosion.

-Battery fluid has strong acid. It corrodes metal very rapidly. If it adheres on skin or enters into eye, it causes for a burn or blindness. At such case, immediately wash skin or eye with lots of water, and ask a doctor to treat it as soon as possible.

-Stop the engine and carry out maintenance and checking service for the battery.

-Remove battery terminal from grounding side (negative terminal) first, and conversely fit the terminal to the grounding side last.

-Do not put tools and hardware on protective cover installed on the battery upper section.

There is a hazard of explosion because the short-circuit may catch fire.

2

1 3

4-35

4

4. MAINTENANCE A.1 Checking Battery Liquid Level 1. Using starter key switch open the door (1) located at left rear of machine, and hold it with stay.

2. Loosen bolts (2) and remove battery protective cover (3).

3. Check the indicator (4) on the battery, and always keep the indicator at blue status. Red and white statuses indicate the low level of battery fluid and the poor charge of battery.

4. Remove battery cell caps (5) and visually inspect electrolyte (acid) level. Proper level is 10 to 15 mm (0.4 to 0.6 inch) above cell plates.

5. Clean vent of battery cap and tighten cap (5) securely.

6. Attach protective cover (3) with bolt.

7. Remove stay and close door, and lock the door (1) with key.

A: Battery B: Upper C: Lower D: Cell Plates

4

A

10~15 mm

B C

D

-Clean battery terminal and apply grease or commercial lube oil rust preventive spray.

-Call in licensed specialty company for the disposal of used battery.

-Be careful not to use the old battery together with new battery. It may reduce the service life of battery. Therefore replace two batteries together with new ones if required to replace.

A.2 Measuring Specific Gravity of Battery Liquid Since the specific gravity of battery liquid varies with respect to the liquid temperature, keep the specific gravity within the range specified in the table.

When the specific gravity is lower than the lower limit, it is necessary to charge the battery.

Ambient Temperature Charge

20C degrees (68F degrees)

0C degrees (32F degrees)

-10C degrees (14 degrees)

100 % 90 % 80 % 75 %

1.26 1.24 1.22 1.21

1.27 1.25 1.23 1.22

1.28 1.26 1.24 1.23

Do not measure the specific gravity of battery immediately after operation, but measure it at ambient temperature.

4-36

4. MAINTENANCE Precaution for Operation in Cold District 1. Pay attention to thermal insulation for battery. The drop in temperature may cause freezing of the battery liquid, or the capacity is significantly reduced.

2. Charge battery earlier in the live time.

B. Fuel Tank Drain Loosen the drain valve (1) to drain the water and deposits in an empty container.

Since the water is deposited during the night, it is effective to drain before starting up the engine in the morning.

1

2

Clean up all spilled fuel.

Fuel oil is highly flammable. Spilled fuel can cause fires.

1. Place an empty container under the drain hose (2) to catch the fuel discharged.

2. Loosen drain valve (1) and discharge water and sediment deposited on the bottom. In this time, be careful not to be showered by flushed fuel.

3. Close drain valve (1) when clean fuel was discharged.

4-37

4

4. MAINTENANCE C. Track Tension

Support lower frame with suitable blocks.

1. Operate swing, arm, bucket and boom controls until machine is set up as shown in.

2. In center of track, measure the distance between the bottom of frame rails and surface of shoe.

3. Perform steps 1 and 2 on right track.

4. To increase track tension, set machine as shown in figure and with grease gun inject extreme pressure No.2 grease into idler adjustment grease nipple (1) until proper tension is reached. Perform this procedure on both tracks.

A 1

Slack: Proper Tension (A): 200 to 230 mm (7.9 to 9.1 inches)

After injecting grease, operate the travel control forward and reverse for the track being adjusted. This will balance the tension between the idler and the sprocket. Then remeasure as shown in figure.

5. To decrease track tension, set machine up as shown in figure.

6. Carefully loosen the adjusting grease nipple (1) to allow grease to escape.

7. Tighten grease nipple (1), measure track tension as shown in figure.

Tightening torque: 49 to 69 N-m (36.6 to 51.4 lbf-ft) 8. If necessary, perform steps 5 through 7 on other track.

1

Grease in track tensioning mechanism is under extreme pressure and can penetrate skin causing severe injury.

Keep face and body away from grease nipple area. Never loosen grease nipple more than one complete turn. If grease does not release after one turn of the nipple, call an authorized NEW HOLLAND service dealer for assistance.

4-38

4. MAINTENANCE

4.13

100 HOUR INSPECTION & MAINTENANCE PROCEDURE

Thoroughly read and understand the "1.SAFETY PRECAUTIONS" of this MANUAL before operating or servicing the machine.

Perform together with daily and 50-hour inspection and maintenance.

A. Lubrication for Bucket Pin Wipe all grease nipples and apply grease until the grease comes out through the gap of pin.

Grease gun is provided inside of side door on the left side of machine.

Greasing If attachment is sunk in water, it is recommended to lubricate it every 8 hours.

2

1. Bucket link pins (1).

2. Bucket cylinder rod pin (2).

3. Idler link to arm pin and arm to bucket pin (3).

4. Arm top pin (4).

3 3 4 1

4-39

4

4. MAINTENANCE

4.14

120 HOUR INSPECTION & MAINTENANCE PROCEDURE

Thoroughly read and understand the "1.SAFETY PRECAUTIONS" of this MANUAL before operating or servicing the machine.

Perform together with daily and 50-hour inspection and maintenance.

A. Swing Motor Reduction Oil

Never change oils on a machine that has just finished working. Allow machine to cool first until oils and fluids are warm not hot.

1. Before checking, find level place, place bucket on the ground, stop engine and move safety lock lever to "LOCKED" position.

2. Check gear oil level with the level gauge (1).

3. If necessary to add oil, remove plug (2) from oil fill port and fill to full level with proper gear oil.

For specified gear oil, refer to the section "LUBRICANT, FUEL & COOLANT SPECIFICATIONS".

4. Attach level gauge (1).

5. Clean filling plug (2) with light oil, and wind seal tape on tube (3) and install plug securely.

Tightening torque: 64.7 to 73.5 N-m {48 to 54 lbf-ft}

4-40

1 2

4. MAINTENANCE B. Travel Reduction Unit Oil

-Travel reduction unit could be under pressure. Carefully loosen plug and remove slowly filled air pressure. Where the plug was loosened abruptly, there is the danger of spouting out of plug and oil. Do not face the plug to prevent from flying plug etc.

-Never change oils on a machine that has just finished working. Allow machine to cool first until oils and fluids are warm not hot.

2 2

1

1

1. Before checking, find level place, stop machine locating plug (1) bottom, and move safety lock lever to "LOCKED" position.

2. Remove level plug (2) and check for short of oil level and contamination. If the oil level is to the top side of level plug, it is in proper level. If shorted, remove level plug (2) and make up short of specified gear oil.

For specified gear oil, refer to the section "LUBRICANT, FUEL & COOLANT SPECIFICATIONS".

3. Clean level plug (2) with light oil, and then attach it in place.

4. Similarly check on the travel reduction unit on the other side.

4-41

4

4. MAINTENANCE

4.15

250 HOUR (3-MONTH) INSPECTION & MAINTENANCE PROCEDURE

Thoroughly read and understand the "1.SAFETY PRECAUTIONS" of this MANUAL before operating or servicing the machine.

Perform together with daily, 50-hour and 120-hour inspection and maintenance.

A. Fan, Alternator, A/C Belt Wear and Tension

Rotating parts can cause injury. Keep away from fan and belt when engine is running. Stop engine before servicing.

If defects such as cuts or surface separations are found during inspection, replace the belt. Keep oil and grease away from the belt, since they may cause the belt to slip and shorten the service life.

This machine is equipped with belts for alternator, fan and air-con.

Check these belts for wear and damage and check the belt tension for slack, and adjust it properly in order to maintain the engine in high performance and the specified service life.

Check the tension of belt by pressing on the center of belt by thumb. If the deflection is within the range shown in the table, it is in normal tension.

Belt

When new belt replaced mm (in)

When inspected mm (in)

Force N (lbf)

Alternator, Fan

4 to 6 mm (0.16 to 0.24")

7 to 9 mm (0.28 to 0.35")

98 (22)

Air-conditioner

3 to 4 mm (0.12 to 0.16")

5 to 6 mm (0.20 to 0.24")

24 (5.2)

-When replace with new belt, there is a lack of initial adaptability of the belt. Run the engine at idling speed for about three or five minutes. After that, adjust the belt tension again.

-New belts get complete initial elongation after being run about two hours.

4-42

4. MAINTENANCE B. Adjustment for Alternator and Fan Belt

Be careful of the alternator and fan belts so that grease and oil are not adhered. The service life may be shortened due to slipping with oil.

1. Open engine hood and support it with stay.

2. Loosen attaching nut (1) and adjusting nut (2) slightly and adjust the belt tension.

3. Loosen adjusting bolt (3), adjust the alternator and fan belts to the specified tension, and tighten attaching nut (1) and adjusting nut (2).

4. After adjustment, start engine and run it at low speed for about 5 minutes.

5. Release the stay which is supporting hood, close engine hood and lock engine hood.

2

1

3

C. Air Conditioning Compressor Belt

Rotating parts can cause injury. Keep away from fan and belt when engine is running. Stop engine before servicing.

4 The improper belt tension may have the performance of compressor lower resulting in the damage of belt and compressor.

1. Open engine hood and support it with stay.

2. Loosen nut (1) for idle pulley slightly and adjust the belt tension while turning the adjusting bolt (2), and then tighten nut (1).

Tightening torque: 41.2 to 51.0 N-m (31 to 38 lbf-ft) 3. After adjustment, start engine and run it at low speed for about 5 minutes.

4. Stop engine and check tension of fan belt.

5. Release the stay which is supporting hood, close engine hood and lock engine hood.

4-43

2

1

4. MAINTENANCE D. Checking the Radiator Hoses The hose replacement before trouble occurs provides economical and good maintenance.

The hose replacement before the hose is damaged will result in cutting costs and minimize the unexpected interruption of work.

Replace the hose (2) and clamp (1) immediately if the crack, permanent set in fatigue and water leakage is found. The immediate replacement could protect engine from serious failure like overheating, etc.

1

1

2 1 2

1

Wear goggles, safety shoes, hard hat, work cloths and work gloves to perform inspection and maintenance on this machine.

D.1 Check 1. Open engine hood and support it with stay.

2. Check the hoses (2) for coolant leak due to loose clamps (1) or cracked and worn hoses.

3. Tighten loose clamp (1) again, and replace the hose (2) on which crack and permanent set in fatigue were found by the following procedure.

4-44

4. MAINTENANCE D.2 Replacing the Radiator Hoses

Avoid being burned by hot liquid and steam. Do not loosen the radiator cap when the coolant is hot. The cooling system is under pressure. Stop the engine and allow enough time for system to cool.

1.

Open engine hood support it with stay.

2.

Loosen 6 bolts on the under cover of lower of radiator, and remove under cover.

3.

Loosen drain valve (3) until the radiator coolant level is lower than the replacing hose (2) and drain coolant in container.

1 1

4.

Loosen drain valve (3) until the radiator coolant level is lower than the replacing hose (2) and drain coolant in container.

5.

Loosen clamp (1), remove damaged hose (2) and replace the hose with new one.

6.

Tighten drain valve.

7.

3 1 Fill coolant in radiator and then fill reserve tank with coolant.

8.

After filling up, tighten radiator cap securely.

9.

Release the stay which is supporting hood, close engine hood and lock bonnet catch.

10.

Return the under cover to original place.

4-45

2

2

4

4. MAINTENANCE E. Checking for Intake Rubber Hose

-Don't touch the rubber hose to avoid burns.

Immediately after stopping the machine or during the operation, the temperature of the rubber hose is very high.

-When the rubber hose is replaced, fill the inlet of air intake with clean cloth to prevent the dust from entering.

E.1 Checking rubber suction hose for air cleaner 1. Check the rubber hose (1) for damage, deterioration and for looseness of band (2).

2. Replace the damaged or deteriorated rubber hose (1) and the band (2) at the same time with new parts.

2

1

2 2

1

2 1 2

E.2 Checking rubber hose for air cooler 1. Check the rubber hose (1) for damage, deterioration and for looseness of band (2).

2. Replace the damaged or deteriorated rubber hose (1) and the band (2) at the same time with new parts.

2 1 2

2 1 2 2 1 2

4-46

4. MAINTENANCE F.

Air-Conditioner Filters Service

The flying debris due to compressed air may cause accident resulting in injury or death.

Wear safety goggles and respirator when cleaning the filters of air-conditioner.

Cleaning recirculate and fresh air filters Recirculate air filter : Every 500 hours Fresh air filter : Every 250 hours Replacing inside and outside air filters Recirculation air filter : After cleaning about 10 times Fresh air filter : After cleaning about 10 times

1 1

The maintenance time shows the reference value. Clean them earlier than the specified time in case where being used in dusty area.

F.1 Removing Fresh Air Filter 1. Catch cover (1) on the left rear side of operator seat and pull it this side.

2. Catch handle grip of fresh air filter (2) through opening from which cover (1) is removed and pull it out upward.

4

2

4-47

4. MAINTENANCE F.2 Removing Recirculation Air Filter 1. The recirculation air filter (3) is placed on the left side under the operator seat.

2. Turn over floor mat, catch handle grip of recirculation air filter (3) and pull it out forward.

3

2 F.3 Cleaning Clean recirculation and fresh air filters.

Clean recirculation and fresh air filters by air blowing F.4 Attaching Procedure Attach recirculation and fresh air filters after cleaning or for replacement by the reverse procedure of the removal.

Insert the recirculation air filter directing the UP side upward.

4-48

4. MAINTENANCE G. Air Cleaner Maintenance

-Direct contact of the body with compressed air, steam and high pressure water can cause injury.

Wear protective glasses, mask, safety cap, safety shoes, etc., to avoid injury.

-Stop engine first and clean and replace the air cleaner element.

-Fro machines equipped with double element and the inner element (2) must be replaced together with the outer element (1). Do not fail to replace the inner element (2) with new one.

-When cleaning outer element, do not remove inner element to avoid dust getting into engine air intake.

2

1

3

4 G.1 Cleaning or Replacement of Outer Element Cleaning and replacement of outer element.

Cleaning : When warning is indicated on multidisplay or every 250 HOURS. Replacement : After 6 times of cleaning or one year whichever comes first.

1. Using starter key, open engine hood support it with stay.

2. Remove 3 clamps (3) on the cover and pull out outer element (1).

3. Clean the inside of air cleaner housing 4. To clean the outer element, blow compressed air (less than 0.2 MPa {29 psi}) up and down along the folds of the filter element interior to remove clogged dust or other contaminants.

5. After cleaning, check on element (1) and if pin hole and excessively thinned part were found, replace it with new one.

6. Release the stay which is supporting hood, close engine hood and lock engine hood.

4-49

4. MAINTENANCE G.2 Replacement of Inner Element 1. Remove outer element (1) first and then remove inner element (2).

2. Cover air outlet side with clean cloth or sealing tape to prevent intrusion of dust.

3. Clean inside of body and remove the cover attached in item 2.

4. Fit new inner element (2) to connector.

5. Install outer element (1) and install cover with clamp (3).

3

2

1

Install the air filter so that "ARROW" position mark is faced upward.

H. Radiator and Oil Cooler Debris Screen

Hot fluids and surfaces can burn. Wear goggles, safety shoes, hard hat, work clothes, and work gloves to perform inspection and maintenance on this machine.

-Direct contact of the body with compressed air, steam and high pressure water can cause injury. Wear protective glasses, mask, safety cap, safety shoes, etc., to avoid injury.

-First remove filter (1) from machine and clean them. If the filter are cleaned on the machine, dust and dirt enter into duct and engine room.

-If tearing of filter is found or clog of dirt can not be removed, replace the filter.

-If deformation of filter flame (made of Aluminum) is found, replace filter with new one.

-When compressed air or jet water is used for cleaning the filter, don not damage the filter by getting too close to screen.

3 2 4

5

4-50

4. MAINTENANCE 1. Open engine hood with starter key.

2. Using starter key, and open the door at the left side of the counterweight.

3. Push lever of filter (1) towards front side of machine to remove the filter. And clean the filter (1).

4. Check filter (1), radiator (2), oil cooler (3), air-cooler (4) and condenser (5) for clogging.

When mud, dust and dead leaves are found, clean them off depending on the degree of dirt.

5. Remove dust, mud and other dirt from their cores and fins using compressed air (0.2 MPa) or water.

6. Push the filter (1) toward machine front and fix the filter (1) with lever.

7. Close the door at the left side of the counterweight, and lock the door.

8. Release the stay which is supporting hood, close engine hood and lock engine hood.

I.

Attachment Lubrication

Wipe all grease nipples and apply grease until the grease comes out through the gap of pin.

Grease gun is provided inside of side door on the left side of machine.

4 1.

2.

3.

4.

5.

6.

Boom cylinder and rod pins (1), (2).

Arm cylinder head pin (3).

Boom foot (Center) pin (4).

Arm cylinder rod pin (5).

Arm to boom pin (6).

Bucket cylinder head pin (7).

3

1

2

4

4-51

4. MAINTENANCE

5

6

7

4-52

4. MAINTENANCE

4.16

500 HOUR INSPECTION & MAINTENANCE PROCEDURES

Thoroughly read and understand the "1.SAFETY PRECAUTIONS" of this MANUAL before operating or servicing the machine.

Perform together with daily, 50-hour, 120-hour and 250-hour inspection and maintenance.

A. REPLACING ENGINE OIL AND OIL FILTER Wear the proper safety equipment when working around hot areas. Do not change oils, engine coolant or filters immediately after machine has been stopped.

Allow machine to cool down before performing maintenance procedures.

F

G

P

H L

Do not touch the heated section during operation or immediately after being stopped. There is a hazard of scalding.

Do not touch the heated section.

-Check the waste oil. If there are metal chips or powder mixed in the oil, contact our distributor.

-Replace it at 50 hours operation for the first use of new machine.

-Replace engine oil filter simultaneously with the engine oil change.

Do not change oil immediately after stopping the engine.

The engine and other parts are very hot after being stopped. To avoid burns, allow the engine to cool before doing oil change.

4-53

4

4. MAINTENANCE 1. Loosen 4 bolts from the cover which is located under the engine.

2. To collect the drained oil, place a container which has 15 liters or more in capacity.

3. Clean the oil filler cap (F) area, and remove the filler cap.

4. Loosen the drain plug (P) of engine oil pan, and drain the engine oil into the container.

5. After draining the engine oil completely, tighten the drain plug (P) securely.

6. Remove oil filter (1) with filter wrench and replace it with new one.

Filter wrench parts No. : YW01T01014P1

1

In this machine, the engine oil filter is located at the separate position from engine. And the engine oil filter is placed on the inside of door on the machine right rear side. When the filter is replaced, do not fail to carry out idling operation for several minutes so as to reach the oil into engine.

Dispose of all hazardous waste in accordance with government environmental regulations.

7. Remove dust, mud, etc. from seal surface of oil filter.

8. Apply engine oil to gasket and fit it in place turning the filter by hand to the position where it is in contact with the filter seal surface.

9. Tighten it 3/4 to 1 turn with filter wrench.

10.Fill it with specified engine oil through oil filler cap (1) referring to the section "4.3 LUBRICANT, FUEL & COOLANT SPECIFICATIONS" in Chapter 4.

11. Attach oil filler cap (F).

12.Check that the reading of oil level gauge (G) is between upper limit and lower limit, crank engine and start the engine. Stop engine after idling for several minutes and check the oil level after about 10 minutes, and if the level is low, fill oil pan with the specified engine oil.

13.Check oil filter attaching face for oil leak.

14.Attach cover in place under engine and close engine hood.

4-54

4. MAINTENANCE B. Replacing the Fuel Pre-Filter The fuel pre-filter is placed on the area where the inside of door on the machine right rear side.

When handling fuel, make sure there are no open flames or other fire hazards near the engine. Wipe off any spilled fuel completely. Spilled fuel could ignite and cause a fire.

7 5

2

4

4

6

3

1

4 1.

2.

3.

4.

5.

Clean the area around the fuel pre-filter.

Prepare container for drain oil.

Close fuel cut valve (1) placed on the halfway of fuel filter line.

Loosen air bleeder plug (2) and drain valve (3) and drain fuel from fuel pre-filter.

Fit the specified filter wrench to the lower side of stiffening ribs and remove case (4).

Parts number : YT01T01008P1 6. Remove element (5) and float (6) placed in the case (4) and replace element with new one.

7. Replace O-ring (7) with new one.

8. After installing O-ring (7) to case (4), install element into case (4).

9. Tighten air breather plug (2) and drain plug (3).

10.Open fuel cut valve (1).

4-55

4. MAINTENANCE C. Replacing the Fuel Filter The fuel filter is placed on the area where the inside of door on the machine right rear side.

When handling fuel, make sure there are no open flames or other fire hazards near the engine. Wipe off any spilled fuel completely. Spilled fuel could ignite and cause a fire.

1. Clean the area around the fuel filter.

2. Place a drip pan under the fuel filter.

3. Close fuel cut valve (1) placed on the half way of fuel filter line.

4. Using a filter wrench, remove the fuel filter.

Parts number : YW01T01014P1 5. Wipe off fuel on the fuel filter cartridge (2) mounting surface of the filter bracket with a cloth.

6. Check new fuel filters for proper seating of the gasket.

2

1

Do not use a filter that has dent on is case.

Dented filter could be damaged during operation and leak fuel resulting in a fire.

7. Apply clean fuel to the gasket on the new fuel filter.

8. Install the fuel filter (2).

9. Open the fuel cut valve (1) of fuel line.

10.After installing the new fuel filter, bleed the fuel filter.

For bleeding the fuel filter, refer to "Bleeding the fuel filter "4.16.D Bleeding the fuel filter" in chapter 4.

11. Start the engine and let it idle for several minutes.

12.Make sure that there is no fuel leak during the engine operation.

4-56

4. MAINTENANCE D. Bleeding Air from the Fuel System This machine is equipped with fuel pump under the engine.

1. Fill fuel tank with fuel.

2. Turn starter key switch "ON" and fueling pump starts operating for approx. two minutes and bleed air automatically.

E. Filter Replacement of Electromagnetic Pump To avoid the engine trouble at starting, replace the filter every 500 hours. And prevent the filter from clogging.

Replacement Procedure 1. Clean the area of the electromagnetic pump.

2. Remove a hose clamp (1) from the electromagnetic pump and disconnect the hose (2). In this time, prevent the entering of dust and dirt.

3. Loosen mounting bolt (3) and remove electromagnetic pump.

2 1 2 3

1

4 Disassembling and Assembling 1. Using spanner wrench, loosen and remove the cover (4).

2. Remove gasket (5), filter (6) and gasket (7) in order.

3. Replace the filter (6), the gaskets (5) and (7) with new ones.

Repair kit number: VI894337-0220 4. Assemble the above parts in the reverse order of disassembling. First, insert the gasket (5) into the cover (4) and tighten it to the electromagnetic pump securely by the spanner.

Used tool: Spanner wrench (17 mm) 5. Install the electromagnetic pump to the specified position, and tighten it by the mounting bolt (3).

Tightening torque: 8.6 to 10.6 N-m {6 to 8 lbf-ft} 6. Install the hose (2) to the electromagnetic pump with the clip (1).

4-57

4. MAINTENANCE

Make sure that the gasket is replaced with new one. Before assembling, clean the cover, magnet and so on.

And check severely the airtightness of the pump.

F. Checking Slewing Ring Fitting Bolts for Loosening Check that bolts (1), (2) securing slewing ring are not loosened. If loosened, remove bolts (1), (2) once, apply Loctite #262 or equivalent, and tighten them again.

1

2 Alternately tighten bolts (1), (2) facing each other in order.

Since the tightening of slewing ring requires special tools, contact our dealer/distributor for assistance.

4-58

4. MAINTENANCE G. Lubricating Push Rod of Control Lever With Grease Remove rubber boot of pilot valve and apply a small amount of grease to the push rod (1) and top end (2) of rotation sliding section.

Removing Boot 1. Insert flat-blade screwdriver into the space between boot (3) and plastic cover (4), and release the cover from 4 claws one by one.

2. After greasing, attach plastic cover (4) and boot (3).

4

4-59

4. MAINTENANCE H. Checking the Air-Conditioner Refrigerant

Sight Glass

4

3

2

1

-Do not loosen parts in the refrigerant circuit because there is a hazard of losing sight by getting coolant in eyes and being frostbitten hands by touching it.

-The inhaling of refrigerant gas has serious influence on human body.

And do not bring fire near the area where refrigerant gas is produced.

When filling or changing refrigerant, confirm the type of refrigerant and use refrigerant in the specified type.

-Refrigerant type and quantity: R-134a: 850 g to 950 g (0.23 to 0.25 lbs) The use of unspecified refrigerant may cause damage of equipment.

H.1 Checking 1. Start the engine. Set the engine speed to the middle speed position.

2. Set the machine to the conditions shown below when checking the refrigerant.

(1)Air conditioner switch (1) : ON (2)Fan switch (2) : HI position (Maximum) (3)Temp. adjustment switch (3) : Lower temp position -Door/Window : Close -Compressor switch (4) : ON (The lamp lit up) 3. Follow the procedure below and check the refrigerant volume by looking through the sight glass (inspection window) on the upper part of the receiver dryer. See right table for better reference.

-Figure (A) : Shows that the refrigerant volume is proper.

-Figure (B) : Shows that the refrigerant is over charged. This will make both high and low pressure extreme and exert a bad influence on the pressure switch operation and the air conditioning system.

-Figure (C) :

4-60

4. MAINTENANCE Shows that the refrigerant is insufficient. Have the refrigerant recharged at your manufacture distributor.

-Keep the air conditioner ready for use all year round.

Operate the air conditioner at least once every week for several minutes to rotate the compressor regardless of the season. This will prevent the refrigerant gas from leaking from the compressor sealing.

-When oil comes out from the pipe joint, contact our dealer/distributor because it is a sign of gas leaking.

-Follow the following regulations to conserve global environment.

1. Do not release refrigerant which is sealed in this unit in to atmosphere.

2. Extract the sealed refrigerant from unit when disposing this unit.

I.

Cleaning Fuel Tank Cap and Strainer

1. Remove cap with starter key.

2. Check cap seal for damage, and if damaged replace it with new one.

3. Clean strainer with light oil and attach it in place. If damaged, replace it with new one.

4. Attach cap and lock it with starter key.

1

4

4-61

4. MAINTENANCE J.

Greasing the Slewing Ring

1. Locate the grease nipple at the front of the slewing ring.

2. Using grease gun filled with general purpose EP grease (to "4.3 LUBRICATION, FUEL & COOLANT SPECIFICATIONS".), lubricate slewing ring with several shots from grease gun.

3. Slew machine 90 degrees right, and repeat step 2. See level on frame.

4. Continue to slew machine at 90 degrees increments and lubricating slewing ring until ring has been completely greased.

Using grease gun, lubricate through grease nipple unteill the grease comes out from bearing seal when the direction of the slewing bearing is changed at every 90 degrees.

(Grease amount : Max. 30 cc / 1 grease nipple)

4-62

4. MAINTENANCE

4.17

1000 HOUR PROCEDURES

(12-MONTH)

INSPECTION

&

MAINTENANCE

horoughly read and understand the "1.SAFETY PRECAUTIONS" of this MANUAL before operating or servicing the machine.

Perform together with daily, 50-hour 120-hour, 250-hour and 500-hour inspection and maintenance.

A. Replacing Return Filters The return filter needs delicate treatment because they role important part for removal of contaminant in hydraulic oil to and preventing trouble of hydraulic component to maintain long service life.

-Use extreme caution when removing the cover. The oil is under high pressure when hot.

Stop engine first, remove breather cap, press valve, release the pressure from tank, and then remove cover.

-Immediately after operation, there is a hazard of getting burn because oil is hot. The filter should be replaced after being cooled.

-Long-life return filter is used.

Place an order of return filter element kit, P/No. YR52V01004R400.

-Change the hydraulic tank return filter on a new machine after the first 50 hours of engine operation then change every 1,000 hours And for specification for breaker, replace return filter by every 250 hours.

4

4-63

4. MAINTENANCE 1. Park machine on firm level ground in the hydraulic level checking position, stop engine and move safety lock lever to "LOCKED" position.

2. Remove breather cap (1) on the upper surface of hydraulic tank and release pressure from hydraulic tank by pressing valve several (5~7) times.

3. Loosen 6 mounting bolts (2) of tank upper cover, remove cover (3).

4. Remove spring (4), bypass valve (5) and element assy (A) from tank.

5. Remove "O-ring" (6) of cover (3).

6. Assemble long-life return filter element kit (A) and place it in.

7. Install cover (3) plates and torque attaching bolts (2) to proper value. Refer to specifications section for torque value.

-The top and bottom direction of element (B) is previously given.

Don't fail to assemble the kit directing the side marked "TOP" upward.

-The joint (C) must be assembled giving a special attention, because the joint (C) fitted once cannot be disassembled.

B. Checking Engine Mounting Bracket for tightening 1. Check the engine mounting bracket (1) and the rubber mount (2) for damage, deterioration and for looseness of bolt (3) and nut (4).

2. If damage or deterioration is found on mount bracket (1) or rubber mount (2), please contact our dealer/ distributor for replacing.

3. Regarding tightening torque of bolt (3) and nut (4), refer to Section "4.6 TORQUE VALUES FOR SPECIFIED".

3,4

3

3,4

1

2

2 2

3 3,4 2 1 2

4-64

3,4

4. MAINTENANCE C. Swing Reduction Lubrication

Immediately after operation, there is a hazard of getting burn because oil is hot.

Start working after being cooled.

1. Park machine on firm level ground, and place the attachment to the ground. Stop engine and move safety lock lever to "LOCKED" position.

2. Using grease gun, lubricate about 100 cc grease (about 1/4 cartridges) through grease nipple (1) of the slewing reduction gear or lubricate grease until the grease comes from the relief valve (2).

1

2

Replace it at 250 hours operation for the first use of new machine.

D. Checking Voltage

4 -Wear hard hat, approved safety glasses or face shield, gloves and other safety equipment when working with batteries.

-Flammable gas (hydrogen gas) is generated in the battery. Do not allow sparks or flames to come in contact with batteries to avoid triggering an explosion.

-Battery fluid has strong acid. It corrodes metal very rapidly. If it adheres on skin or enters into eye, it causes for a burn or blindness.

At such case, immediately wash skin or eye with lots of water, and ask a doctor to treat it as soon as possible.

-Stop the engine and carry out maintenance and checking service for the battery.

-Remove battery terminal from grounding side (negative terminal) first, and conversely fit the terminal to the grounding side last.

-Do not put tools and hardware on protective cover installed on the battery upper section.

There is a hazard of explosion because the short-circuit may catch fire.

1. Measure the voltage of battery and if the measured value does not reach the specified voltage, recharge or replace battery.

-Clean battery terminal and apply grease or commercial lube oil rust preventive spray.

-Call in licensed specialty company for the disposal of used battery.

-Be careful not to use the old battery together with new battery. It may reduce the service life of battery. Therefore replace two batteries together with new ones if required to replace.

4-65

4. MAINTENANCE

4.18

2000 HOUR INSPECTION & MAINTENANCE PROCEDURES

Thoroughly read and understand the "1.SAFETY PRECAUTIONS" of this MANUAL before operating or servicing the machine.

Perform together with daily, 50-hour 120-hour, 250-hour, 500-hour and 1000-hour inspection and maintenance.

A. Changing Engine Coolant

Avoid being burned by hot liquid and steam. Do not loosen the radiator cap when the coolant is hot. The cooling system is under pressure. Stop the engine and allow enough time for system to cool.

Engine anti-freeze/coolant liquid is flammable and can cause injury.

-Keep anti-freeze /coolant liquid away from flames and sparks.

-Avoid contact with eyes and skin. If anti-freeze/coolant contacts eyes or skin, immediately wash with clean water for several minutes and seek medical treatment.

Immediately after operation, there is a hazard of getting burn because coolant is hot.

Start working after being cooled.

Use clean soft water for coolant in which lime deposit is not produced.

The water is corrosive in engine operating temperature. The coolant at the time of shipment is mixed with 50% of "Long Life Coolant" to protect the cooling system from rusting and freezing.

-Non-amine antifreeze mixture is used for this machine.

-Change coolant ahead of the specified period when it was dirty and/or bubbling.

1.

Find firm level ground, place bucket on the ground, stop engine, and move safety lock lever to the "LOCKED" position 2.

Using starter key, open engine hood and hold it with stay.

3.

Loosen radiator cap (1) slowly, check that the pressure is released completely, push cap in, and remove the cap by loosening it further. Prepare hose for pouring water.

4-66

1

4. MAINTENANCE 2

4.

Remove undercover under the radiator, and prepare container for coolant under drain valve (2) and drain plug (3) on the engine side face.

5.

After draining, close drain valve (2) and drain plug (3) and fill it with clean soft water.

6.

Open drain valve (2) and drain plug (3), and operate engine by low idling, and wash it with flowing water for 10 minutes.

During washing with the aid of flowing water, regulate the pouring water volume and discharging water volume to keep the radiator in full condition.

During water flowing, maintain a continual watch for the disconnection of pouring water hose from the radiator water filling port.

7.

After flowing water washing, stop engine and stop pouring water, and then after discharging water, close drain valve (2) and drain plug (3).

8.

After discharging water, clean it with cleaning solution.

Regarding to how to use cleaning solution, follow the instructions in "Instruction Manual" for the cleaning solution in use.

9.

After cleaning, open drain valve (2) and drain plug (3) and 3 discharge water completely, and then close the drain valve and drain plug and feed soft clean water close to the feed water port.

10.

After water is fed close to feed water port, open drain valve (2) and drain plug (3) and continue flowing water washing until clean water is discharged.

During water flowing washing, regulate the pouring water volume and discharging water volume to keep the radiator in full condition.

11.

When clean water is discharged, stop engine and close drain valve (2) and drain plug (3).

And then feed "Long Life Coolant" in proper concentration until it is overflowed from the filling port.

12.

When the engine coolant is replenished, fill the cooling water after loosening the plug (5) of the EGR cooler (4).

Wipe cleanly spilled water off.

4-67

5,6

4

4

4. MAINTENANCE

All air in the engine could not be bled through the plug of EGR cooler.

The gasket was fixed in the plug part of air bleeding. If any damage is found on the gasket (6), replace it with a new one.

Air bleed plug Tightening Torque : 24.5 to 30.5 N-m {18 to 23 lbf-ft} 13.

Run engine by low idling for 5 minutes to remove air contaminated in coolant and continue low idling operation for 5 minutes further.

(During this operation, leave the cap of filling port removed.)

14.

Discharge coolant from reserve tank (7) and clean inside of the reserve tank and fill tank with "Long Life Coolant" in proper concentration to the mid point of FULL(A)-LOW(B) marks.

15.

Stop engine, and after 3 minutes pour soft clean water in radiator to the edge of radiator filler cap, and then tighten radiator cap.

16.

Replace the support of stay, close engine hood and lock hood with starter key.

7 A B

B. Changing Oil in Swing Reduction Unit

-Immediately after operation, there is a hazard of getting burn because oil is hot. Start working after being cooled.

-Swing reduction unit could be under pressure, carefully loosen plug and remove slowly till air pressure is released.

• •

Container for drain oil: 2 L {0.5 gal} or more Changing oil quantity: 1.5 L {0.4 gal}

3 2

1

Change the swing reduction unit oil on a new machine after the first 500 hours of engine operation then change every 2000 hours.

4-68

4. MAINTENANCE 1. Prepare container for drain oil.

2. Remove drain plug (1) on the rear lower side of swing reduction unit and drain oil in container.

3. Clean drain plug (1) with light oil, dry it with drain plug.

Tightening torque: 108 N-m {80 lbf-ft} 4. Remove fill plug (2), and fill with the specified gear oil in the specified quantity referring to "4.3 LUBRICANT, FUEL & COOLANT SPECIFICATIONS".

5. When the reading is within the specified range of level gauge (3), it is normal level.

6. Clean filling plug (2) with light oil, and wind seal tape on tube (4) and install plug securely.

Tightening torque: 64.7 to 73.5 N-m {48 to 54 lbf-ft}

-Check the metal chips and powder in the drained oil. If the oil includes such contaminant, contact our dealer/ distributor for repair.

-Dispose of all hazardous waste in accordance with government environmental regulations.

C. Change Oil in Travel Motor Reduction Units

-Immediately after operation, there is a hazard of getting burn because oil is hot.

Start working after being cooled.

-Travel reduction unit could be under pressure, carefully loosen plug and remove slowly till air pressure is released.

• •

Container for drain oil: 3 L {0.79 gal} or more Changing oil quantity: Right and left 1.35 L {0.36 gal} each

4

Change the travel reduction units oil on a new machine after the first 500 hours of engine operation then change every 2000 hours.

2 2

1

1

1.

2.

3.

4.

Position the machine directing drain lug (1) downward and stop engine.

Remove drain plug (1) and level plug (2) and drain oil in container.

After draining oil completely, clean drain plug (1) with light oil and attach it in place.

Fill with the specified oil in the specified quantity through hole for level plug (2) until the oil overflowed from level plug (2) referring to the section ""4.3 LUBRICANT, FUEL & COOLANT SPECIFICATIONS".

5. Clean level plug (2) with light oil and attach it in place.

4-69

4. MAINTENANCE 6. Similarly, change oil of travel reduction unit on the other side.

-Check the metal chips and powder in the drained oil. If the oil includes such contaminant, contact our dealer/ distributor for repair.

-Dispose of all hazardous waste in accordance with government environmental regulations.

D. Cleaning Suction Strainer

-Use extreme caution when removing the cover.

The oil is under high pressure when hot. Stop engine first, remove breather cap, press valve, release the pressure from tank, and then remove cover.

-Immediately after operation, there is a hazard of getting burn because oil is hot.

The service should be done after being cooled.

1.

Park machine on firm level ground in the hydraulic level checking position, stop engine.

2.

Move safety lock lever to "LOCKED" position.

3.

Clean the surface around hydraulic tank to prevent intrusion of foreign matter.

4.

Remove breather cap (1) on the upper surface of hydraulic tank and release pressure from hydraulic tank by pressing valve (A) several (5 to 7) times.

5.

Loosen 6 mounting bolts (2) of tank upper cover, remove cover (3).

Do not drop bolt or others into the tank during the work.

4-70

1

A

4. MAINTENANCE 2

6.

Take out suction strainer (4).

7.

Clean strainer with light oil or washings, dry it and check strainer for damage. If damaged, replace the strainer with new one.

8.

Check O-rings (5) and (6) on the bottom of strainer for wear and damage. If worn or damaged, replace the strainer with new one.

9.

Insert strainer (4) into suction tube.

10.

Install cover (3) with bolt (2).

Tightening torque: 41.9 to 51.1 N-m (30.9 to 37.7 lbf-ft)

3

4

6

11.

Start engine and operate it by low idling for several (5 to 7) minutes. Operate each cylinders and swing, and then return the machine to the hydraulic level checking position. Stop the engine and check the oil level, if the level is low, make up the oil.

5 5 3.

m

m

82

E. Checking Swing Bearing Teeth

The deterioration of grease may cause damage of pinion shaft and swing bearing of swing reduction unit.

If the grease is white due to moisture content, and the viscosity of grease is lowered, replace the grease with a new one. Also, if the grease is contaminated with a large amount of water, replace the grease. In that case, contact our dealer/distributor.

1. Grease may be cloudy due to slight contamination of water, but there is no malfunction if the viscosity is high. When water is there, loosen bolts (1) and spring washers (2) on the lower side of lower frame, remove cover (3) and packing (4) and drain water.

4 3 2 1

4-71

4

4. MAINTENANCE F.

Cleaning of Pilot Line Filter

Immediately after operation, there is a hazard of getting burn due to hot hydraulic oil gushed. Clean the filter after being cooled.

Carry out the replacement of filter after completely releasing internal pressure from hydraulic system.

1. Open side door on the pump side, remove hose (1), connector (2) and line filter (3), clean line filter with light oil, and attach line filter (3) in place.

3 2 1

4-72

4. MAINTENANCE

4.19

5000 HOUR INSPECTION & MAINTENANCE PROCEDURE

Thoroughly read and understand the "1.SAFETY PRECAUTIONS" of this MANUAL before operating or servicing the machine.

Perform together with daily, 50-hour 120-hour, 250-hour, 500-hour and 1000-hour inspection and maintenance.

A. Change Hydraulic Oil

-Use extreme caution when removing the cover. The oil is under high pressure when hot.

Stop engine first, remove breather cap, press valve, release the pressure from tank, and then remove cover.

-Immediately after operation, there is a hazard of getting burn because oil is hot. The filter should be replaced after being cooled.

Since the deterioration of hydraulic oil with the breaker installed is larger than that of normal bucket digging work, service it referring to the section "Checking and service" for hydraulic breaker.

4

1

• •

Container for drain oil: 48 L {12.7 gal} or more Changing oil quantity: 48 L {12.7 gal}

1.

Park machine on firm level ground, swing upper structure so that drain plug (1) on the lower section of hydraulic tank is positioned to the mid point of right and left track shoe.

2.

Retract arm cylinder and bucket cylinder, place bucket and blade (when installed) on the ground and stop engine.

3.

Move safety lock lever to "LOCKED" position.

A: Valve

4-73

2

A

4. MAINTENANCE 4.

Clean the surface around hydraulic tank to prevent intrusion of foreign matter.

5.

Remove breather cap (2) on the upper surface of hydraulic tank and release pressure from hydraulic tank by pressing valve (A) several (5 to 7) times.

6.

Loosen 6 mounting bolts (3) of tank upper cover, remove cover (4).

7.

Drain the hydraulic oil into container using oil pump.

3 4

-Do not drop bolt or others into the tank during the work.

-Dispose of all hazardous waste in accordance with government environmental regulations.

8.

Place container for drain oil under drain plug (1) of the hydraulic tank bottom.

9.

Loosen drain plug (1) on the bottom of hydraulic tank slowly and drain hydraulic oil completely.

10.

Clean drain plug (1) and install it in place.

Tightening torque: 98 to 118 N-m (72 to 87 lbf-ft)

11.

Fill hydraulic tank with hydraulic oil through filler port.

Fill with hydraulic oil watching the level gauge (G) for oil level.

12.

Attach filler port cover (4) with 6 bolts (3).

Tightening torque: 41.9 to 51.1 N-m (30.9 to 37.7 lbf-ft) 13.

Start engine and operate it by low idling for several (5 to 7) minutes. Operate each cylinders and swing, and then return the machine to the hydraulic level checking position. Stop the engine and check the oil level, if the level is low, make up the oil.

4-74

1

H G L

4. MAINTENANCE

4.20

MACHINE STORAGE

A. Machine Storage The following procedure applies when the machine is to be stored for a mouth or more.

1. Perform all inspection and maintenance procedures as previously described in this section.

2. Thoroughly clean the machine, inspect for damaged or worn parts and components and replace or repair all damaged or worn parts.

3. Completely fill fuel tank with fresh, clean fuel to aid in preventing condensation of moisture inside the fuel tank.

4. Move machine to an indoor location for storage.

5. Operate bucket and arm completely "IN" extending cylinders. Then lower boom until attachment is resting on the floor.

6. Coat cylinder rods with a heavy coat of grease to prevent corrosion during storage.

7. Remove batteries and store in a well ventilated, warm area.

Protect CPU and all electrical components from water and steam when cleaning the machine.

4

B. Care During Storage 1. Every 30 days during storage, it will be necessary to start and run the machine to circulate the fluids through the systems. Before starting clean cylinder rods and after running re-grease cylinder rods.

Run and operate machine for approximately 1 hour to allow all fluids to circulate well and reach normal operating temperatures.

4-75

4. MAINTENANCE C. Strage Up After 1. Perform all Inspection and maintenance procedures as described in this section before bringing machine out of storage for normal operation.

2. Remove drain plugs from travel motor and slewing gear reduction units to drain off any moisture which may have accumulated during storage.

3. Carefully and closely inspect all hydraulic hoses after long periods of storage for signs of deterioration. Replace all hoses showing these signs.

4-76

5. TRANSPORTATION

5. TRANSPORTATION

5

5-1

5. TRANSPORTATION

5-2

5. TRANSPORTATION

5.1

GROUND TRANSPORTATION

5.1.1

MACHINE PREPARATION

1.

2.

3.

4.

5.

6.

Know the total weight, length, width and height of the machine being transported.

Know route to be traveled. Investigate bridges, overpasses, height of road signs on route.

Obtain any permits required from proper government agencies for machine transportation.

Use only a trailer with a rated capacity sufficient to transport the machine.

Make certain trailer has ramps or a ramp is available for loading and unloading the machine.

When the machine is transported, to prevent an incident, make sure that all doors, guards and access panels were correctly locked.

Unit : mm (ft-in) 2,230 (7'-3")

2,240 (7'-4") 2,870 (9'-5")

360 (14.2")

*735 (28.9")

2,960 (9'-9")

2,780 (9'-2")

1,290 (4'-3")

600 (23.6")

2,490 (8'-2")

3,270 (10'-8") 6,380 (20'-11")

Marked * dimensions do not include height of shoe lug.

Dimensions and weights are 2.13 m (7'-0") Arm, 0.22 m3 (0.29 cu.yd) Bucket and 3.84 m (12'-7") Boom.

Weight

Machine Model

450 mm (17.7") Shoe 600 mm (23.6") Shoe

E70BSR

7,750 kg (17,090 lb)

7,980 kg (17,600 lb)

5-3

5

5. TRANSPORTATION Unit : mm (ft-in)

2,780 (9'-2")

1,000 (3'-3")

3,780 (12'-5")

6,390 (20'-12")

2,750 (9'-0")

3,750 (12'-4")

510 (20")

When the long arm 2.13 m (7'0") equipped machine is transported, remove the bucket as shown in the above figure to limit the overall height of the machine within 3.8 m (12'6").

5-4

5. TRANSPORTATION 5.1.2

LOADING/UNLOADING THE MACHINE

-The machine loading and unloading work should be carried out on the firm and level ground.

-Use ramps which have sufficient width, length, thickness and strength.

-Slow speed traveling is necessity to load and unload the machine.

-It is hazardous to use the attachment for loading and unloading the machine. Do not use the attachment for loading and unloading.

-Use only the traveling controls when the machine is on the ramp.

-Be prepared for a change in the machine position as the machine travels up or down the ramp.

The machine may rock forward or rearward as the machine center of gravity changes when traveling on the ramp or on the border between the track/trailer and the ramp.

-Turn auto accel switch off surely. The operation with the auto accel switched on may cause sudden engine speed change.

-Remove mud, etc. of the crawler track link of machine surely to prevent skidding.

And remove water, snow, grease oil, etc. surely.

-Do not change the course on the ramps to prevent rolling over. Return to ground or trailer's bed once and change the traveling direction.

5 A. In Cases where Making Use of ramps 1.

Load machine on firm and level ground.

2.

Do not fail to put blocks to the tire of trailer to prevent machine from moving.

3.

The width and height of the loading area (earthen bank or loading platform ramp) must be high enough to match the trailer and wide enough to match the width of the machine and trailer, or wider.

A 4.

Make sure the machine position is aligned to ramps before traveling up the ramps, and travel slowly with the dozer (if equipped), raised position. The arm and boom held at angle shown in the figure, and the dozer equipped and attachment lowered as much as possible but do not interfere with trailer bed. And travel slowly.

A. The ramp slope should be 15 degrees or less

5-5

5. TRANSPORTATION 5.

Since machine is tend to be unstable when going over the rear wheel, travel slowly and carefully.

6.

Since the machine is bent-forward when traveling over the rear wheel, travel forward slowly to the required position giving particular attention to the attachment so as not to touch the bed of trailer.

To prevent the arm and bucket cylinder(s) from any damage, you are advised to follow the following instructions.

Do not have the arm and/or bucket cylinder fully extended to a "RAMP OVER CENTER" situation. This allows sudden and abrupt contact of the arm or bucket to a trailer deck, ramp or the ground.

This can result in internal mechanical contact, which can stretch the cylinder rod(s).

7.

After arriving to the required position, turn the upper structure 180 degrees slowly.

8.

After positioning, lower attachment softly.

5-6

5. TRANSPORTATION B. Use of Platform or Earth Banking 1.

Make the width of the earth banking (raising the ground level) enough to the machine width.

2.

Make the earth banking strong enough in order no to turn over the machine during loading/unloading due to broken side slope of the earth banking.

If necessary, provide some supporting posts to reinforce A both side of the banking.

3.

The height of the platform or banking must correspond to that of the base of truck/trailer.

4.

At loading the machine, climb up to the truck/trailer from front end of the machine for the case of the machine with attachment, and from back end for the machine without attachment.

5.

Set the machine at the prescribed position on the truck/trailer.

A. 15 degrees or less C

Loading Machine without Front Attachment

When loading the machine the front attachment is removed, direct counterweight upward direction on the slope.

5

5-7

5. TRANSPORTATION 5.1.3

SECURING THE MACHINE

-Retract the antenna of radio during transport. And remove mirror when required. Keep the removed parts surely.

-To protect the bucket (attachment) cylinder from damage during transport, place a wood block at the end of the bucket link to keep the cylinder from contact with the truck bed.

After the machine is loaded and positioned, fix the machine by the following procedures.

1. Move the safety lock lever to the "LOCKED" position 2. Turn all switches off and remove the engine starter key.

Lock all covers and the cab door.

3. Position blocks at the front and rear of the crawler belts and secure them. This will prevent the machine from moving during transport.

4. Position a block under the excavator arm to support during shipping.

5. Tie down the machine using rigging sufficient for safe transport.

A. Unloading the Machine

AVOID INJURY OR DEATH -Slow speed traveling is necessity to load and unload the machine.

-Be prepared for a change in the machine position as the machine travels up or down the ramp. The machine may rock forward or rearward as the machine center of gravity changes when traveling on the ramp or on the border between the track/trailer and the ramp.

1.

Load and unload machine on firm and level ground.

2.

Do not fail to put blocks to the tires of trailer to prevent machine from moving.

Accord the distance of two ramps with that of centers of crawlers and incline ramps at angle of 15 degrees or less (A).

3.

Remove chain or wire rope which is used to fix the machine.

5-8

A

5. TRANSPORTATION 4.

Start engine.

5.

Move safety lock lever to "UNLOCKED" position.

6.

Press travel speed change switch of switch panel on gauge cluster and change the speed to low speed.

Check that travel speed is set to low speed by watching display.

7.

Raise attachment and travel slowly with placing attachments as shown in figure.

8.

Park the machine horizontally on the rear end of trailer and then stop it.

9.

Set arm and boom to angle 90 to 110 degrees and travel down slowly from trailer to ramps. In this time, the bucket position should be close to ground.

To prevent the arm and bucket cylinders from any damage, you are advised to follow the following instructions.

Do not have the arm and/or bucket cylinder fully extended to a "RAMP OVER CENTER" situation. This allows sudden and abrupt contact of the arm or bucket to a trailer bed, ramp or the ground.

This can result in internal mechanical contact, which can stretch the cylinder rod(s).

10.

Travel down on ramps slowly while operating boom and arm softly until the machine passes through the ramps completely.

5-9

5

5. TRANSPORTATION

5.2

LIFTING MACHINE

1,800 mm (5'-11'')

The following procedures are for lifting the machine, as built by NEW HOLLAND. These procedure do not take into account modifications made to the machine that affect machine weight or center or gravity.

Breddeholder 3600 mm (11'-10'')

3,500 mm (11'-6'')

unkt

598mm (1'-11'')

146mm (0'-6'')

688mm (2'-3'')

Plasser blokker mellom hver kabel og ramme

6,500 mm (21'-4'')

okker er kabel pp

5-10

5. TRANSPORTATION

-Wire rope or chain used for lift the machine must be of sufficient weight lifting capacity for this machine.

-Improper lifting method or rope/chain rigging may cause unexpected movement or slip of the machine when lifted, resulting in serious injury or death or damage to the machine.

-When lifting the machine operate the controls, slowly and smoothly avoiding any sudden/fast control movement for safety of people involved and lift rigging.

-When the machine is lifted with assistance of one or more workers operation signals/communication must be understood by all involved to avoid injury or death.

-During the machine lift procedure, keep people away from the area, especially the area under the machine.

-Do not use the counterweight lifting eyes to lift whole machine.

This lifting up procedure is applicable for machines in standard specification.

The lifting procedure differs for each attachment type and each machine in option. In such cases, contact our dealer/distributor.

Carry out the lifting work on firm level ground.

1. Position the machine as shown in the figure.

2. Position the boom to the front of machine.

3. Stop the engine and move safety lock lever to "LOCKED" position. Get off machine. Check the operator's seat and area for any loose item, tools, etc. that could fall or cause a problem or injury during the procedure and remove or secure them.

4. Stop the engine and remove starter key, and get off the machine.

5. Use wire rope and expander of sufficient length to prevent interference with the machine body when lifting up machine. Cover wire rope with cloth to protect machine from damaging if necessary.

6. Pass through wire ropes between 1st and 2nd lower rollers on both front and rear sides of machine as shown in figure.

7. Lift up machine with an angle of two wire ropes adjusted within the range of 12 to 30 degrees slowly.

8. After working, stop machine once and lift machine again slightly after machine has stabilized.

5

5-11

5. TRANSPORTATION

5.3

INSTALLATION AND REMOVAL OF MIRROR FOR SAFETY

Mirror locations are shown in figure.

When the machine needs repairing or transportation, follow the next procedures.

-Be sure to clean mirror before starting operation to ensure good visibility around machine.

If the visibility around machine is not secured sufficiently, it may cause collisions and accidents resulting in injury and death.

-To avoid the damage or break, do not install the mirror and so on to the handrail of cab entrance. If the mirror and so on is installed to the hand rail, the attaching part of handrail is stressed excessively.

-Do not attach the mirrors except the genuine mirrors (A, B, C and D).

2390 mm (7'-10") B Speil A

1")

mm

2700 mm (8'-10")

C

When the machine is shipped, the both side mirrors of the right frame and the cab, mirror were removed. Install them according to the next procedures.

5-12

5. TRANSPORTATION Mirror A

1 2

E

• • • • • •

Adjust the mirror (A) so that the operator can identify the person who stands on the left rear ends of machine (or post of 1.5m high and 30cm in diameter).

Install the mirror on the small diameter part (E) of the stay shown in the above figure.

Install the mirror so that the mirror (A) does not come in contact with the stay (1) of the mirror.

During adjustment, if the movement of the mirror (A) is not smooth, loosen nut (2) of the mirror and adjust it.

Tightening torque of nut (2) M10: 18.6 to 25.5 N•m (13.7 to 18.8 lbf•ft) Adjust mirror so that the machine side shown in the right figure is reflected in the mirror.

Regarding visible range, refer to previous page.

Mirror B

B 4

5

3

• • • • • •

Adjust the mirror so that person who stands on the right rear ends of machine (or post of 1.5m high and 30cm in diameter) can be identified from operator.

Install mirror on position shown in the figure.

Install it so that the mirror (B) does not come in contact with the stay (3) of the mirror.

If the movement of mirror (B) on adjusting is not smooth, loosen nut (4) of mirror and adjust it.

Tightening torque of nut (4) M8 : 8.6 to 12.7N•m {6.3 to 9.4lbf•ft} Adjust the mirror so that the machine right side is reflected in the mirror as shown in the figure.

Regarding visible area, refer to the shaded range on previous 1.11.

5-13

5. TRANSPORTATION Mirror C

6

5

C

Adjust mirror so that person who stands on the right front of machine (or post of 1.5 m height and 30 cm in diameter) can be identified from operator's seat.

• • • •

Install mirror to the position shown in the figure.

Install mirror so that the mirror (C) does not come in contact with the mirror stay (5).

If the movement of mirror (C) on adjusting is not smooth, loosen nut (6) of mirror and adjust it.

Tightening torque of nut (6) M8 : 8.6 to 12.7 N•m {6.3 to 9.4 lbf•ft} Regarding visible area, refer to the shaded range on previous 1.11.

Mirror D

7

D

• • •

•

Install the mirror on the position shown in the above figure.

Install the mirror so that the mirror (D) does not come in contact with the stay (7) of the mirror.

During adjustment, if the movement of the mirror (A) is not smooth, loosen the adjusting screw (2) of the mirror and adjust it.

Tightening torque of adjusting screw (8) M10: 18.6 to 25.5N•m (13.7 to 18.8lbf•ft) Regarding visible range, refer to previous page.

5-14

6. SPECIFICATIONS

6. SPECIFICATIONS

6

6-1

6. SPECIFICATIONS

6-2

6. SPECIFICATIONS

6.1

GENERAL SPECIFICATIONS Item Working Weight

Unit

E70BSR

kg

7,750 (17,090)

3

m (cu•yd)

0.22 (0.29)

-

ISUZU DIESEL ENGINE AU-4LE2X Water-cooled, 4 cycle 4 cylinder direct injection type diesel engine with intercooler turbo-charger.

Engine Output-Rating

kW/min-1

41 / 2,200

A

Overall Length

mm (ft-in)

6,380 (20-11)

B

Overall Height

mm (ft-in)

2,960 (9-9)

C

Overall Width of Crawler

mm (ft-in)

2,320 (7-7)

D

Width of Crawler Shoe

mm (inch)

450 (17.7)

E

Height to Top Cab

mm (ft-in)

2,780 (9-1)

F

Ground Clearance of Under Carriage

mm (inch)

360* (14.1)

G

Radius of Rear End

mm (ft-in)

1,290 (4-3)

H

Basic Machine Length

mm (ft-in)

3,270 (10-8)

I

Overall Length of Crawler

mm (ft-in)

2,860 (9-4)

J

Center Distance of Tumblers

mm (ft-in)

2,240 (7-4)

K

Ground Clearance of Rear End

mm (ft-in)

730* (2-4)

L

Width of revolving upper structure

mm (ft-in)

2,230 (7-3)

M

Dozer blade (Down/up)

mm (inch)

245 (9.8) / 355 (14.0)

Ground Pressure

kPa (psi)

34 (4.93)

Swing Speed

min-1 (rpm)

11.5 (11.5)

Travel Speed [Low (1st)/High (2nd)]

km/h (mph)

2.8 / 5.3 (1.7 / 3.3)

% (deg)

70 (35)

Bucket Heaped Engine Maker

Gradeability

-The attachment is with the arm of 2.13 m (7'-0") and bucket "SAE heaped" of 0.22 m3 (0.29 cu•yd) attached.

-Marked * dimensions do not include height of shoe lug.

6

6-3

6. SPECIFICATIONS L

M

F

K

E

B

G

M

J I

D C

H A

6-4

6. SPECIFICATIONS

6.2

SHOE TYPES

Grouser Shoes Type

Rubber Shoes

450 mm (17.7")

600 mm (23.6")

450 mm (17.7")

450 mm (17.7")

For General Soil (Standard)

For Soft Soil (Optional)

For Soft Soil (Optional)

For Soft Soil (Optional)

kg

7,750

7,980

7,910

7,940

Height to Top Cab

mm

2,780

2,780

2,780

2,780

Ground Clearance of Under carriage

mm

360*

360*

360*

360*

Basic Machine Length

mm

3,270

3,270

3,270

3,270

Overall Length of Crawler

mm

2,860

2,870

2,860

2,860

Overall Width of Crawler

mm

2,320

2,470

2,320

2,320

kg

34

27

35

35

Use Working Weight

Specific ations

Flat Shoes

Ground Pressure

-Do not employ shoes other than 450 mm (17.7") grouser shoe on rough ground (site covered with much rocks and gravels).

The traveling and digging works on the rough ground may cause bent of shoe, looseness of shoe bolt, etc. and also damage of under carriage (link, roller, etc.).

-The attachment is with the arm of 2.13 m (7'-0") and bucket "SAE heaped" of 0.22 m3 (0.29 cu•yd) attached.

-Marked * dimensions do not include height of shoe lug.

6

6-5

6. SPECIFICATIONS

6.3

WORKING RANGES

A. Backhoe Attachment

G

E

H D

C

A A'

L

B J F

K

YT11Z00164P1 YT11Z00162P1 Enhet : mm (ft-in) Tilbehør Gjenstand

1.71 m (5’-7") Arm

2.13 m (7’-0") Arm

+ 0.28 m3 (0.37 cu•yd) Grabb

+ 0.28 m3 (0.37 cu•yd) Grabb

A Maksimal graverekkevidde

6,460(21-2)

6,850(22-5)

A’ Maksimal graverekkevidde på bakken

6,300(20-8)

6,700(21-11)

4,160(13-8)

4,580(15-0)

* B Maksimal gravedybde * C Maksimal gravehøyde

7,390(24-3)

7,690(25-2)

* D Maksimal avlessingklaring

5,330(17-6)

5,630(18-5)

*E Minimum avlessingklaring

2,530(8-4)

2,220(7-3)

* F Maksimum vertikal vegg gravedybde

3,450(11-4)

3,860(12-8)

1,760(5-9)

2,120(6-11)

5,730(18-9)

5,750(18-10)

G Minimal svingradius * H Høyde ved minimum svingeradius * J 8243,84 cm gravedybde K Horisontal gravebane ved L bakkens nivå

3,800 (12-6)

4,270 (14-0)

Bane

2,850 (9-4)

3,270 (10-9)

Minimum

1,890 (6-2)

1,870 (6-2)

Marked * dimensions do not include height of shoe lug

6-6

6. SPECIFICATIONS B. Face Shovel Attachment

A A'

E

D'

H D

C

G

L

J

B

K

YT11Z00165P1 YT11Z00166P1 Enhet : mm (ft-in) Tilbehør Gjenstand A Maksimal graverekkevidde

1.71 m (5’-7") Arm

2.13 m (7’-0") Arm

+ 0.28 m3 (0.37 cu•yd) Grabb

+ 0.28 m3 (0.37 cu•yd) Grabb

6,550(21-6)

Maksimal graverekkevidde på A’ bakken

6,940(22-9) 6,380(20-11)

* B

Maksimal gravedybde

* C

Maksimal gravehøyde

7,490(24-7)

7,780(25-6)

* D

Maximum damping clearance

5,430(17-10)

5,730(18-10)

* D

'Maksimal avlessingklaring (45°)

4,630(15-2)

4,770(15-8)

* E

Minimum avlessingklaring

2,450(8-0)

2,130(7-0)

Minimum swing radius

1,760(5-9)

2,120(6-11)

Max. height at min. swing radius

5,730(18-9)

5,750(18-10)

3,900(12-10)

4,360(14-4)

Bane

2,030(6-8)

2,660(8-9)

Minimum

4,240(13-11)

4,010(13-2)

G * H * J8

(243,84 cm) gravedybde

K Horisontal gravebane L ved bakkens nivå

4,240(13-11)

6,780(22-3)

Marked * dimensions do not include height of shoe lug

6-7

4,660(15-3)

6

6. SPECIFICATIONS

6.4

BUCKET AND ARM COMBINATIONS

A. Front Attachment Variation (1) Outline This machine is equipped with attachments in various types in order to comply with various operations.

• When large capacity bucket is used, it should be used in combination of short arms to secure the stability of machine and not to be forced to operate machine, front section and each cylinder.

• When long boom and arm are used, conversely combine with the small capacity bucket.

Type

Graveskuff

Grabb (m 3) (cu•yd) Utvendig bredde på grabb (mm) SAE

SAE

(Heaped)

(Struck)

0.11

0.09

(0.14)

(0.11)

0.14

0.12

(0.18)

(0.16)

0.18

0.14

(0.23)

(0.18)

0.22

0.18

(0.29)

(0.24)

0.28 (0.37) (STD)

0.21 (0.27)

0.35

0.26

(0.46)

(0.34)

0.35 (0.46) side pin

0.26 (0.34)

Med sidekuttere

Uten sidekuttere

Kan vendes

Antall tenner

1.71

2.13

m Arm

m Arm

Arm Vekt 1.71 m

—

400

3

Yes

Yes

150

480

410

3

Yes

Yes

160

550

480

3

Yes

Yes

170

650

580

4

Yes

Yes

190

750

680

4

Yes

Yes

210

850

780

4

Yes

Yes

220

850

780

4

Yes

Yes

210

Hydraulikkhammer

—

—

—

—

—

—

—

—

Knuser

—

—

—

—

—

—

—

—

2.13 m

If any other bucket except for the backhoe bucket is turned over and used for excavation, damage to the arm and bucket may occur.

: Standard combination : General operation; Excavation or loading of sand, gravel, and clay : Light operation; Mainly loading of loose gravel (e.g., cultivation or loading of sand or gravel) : Prohibited combination; NEW HOLLAND's warranty does not cover any damages resulting from theses combinations. Do not use these combinations.

Install only genuine attachment recommended by NEW HOLLAND on the machine. NEW HOLLAND is not liable for any damages to the machine or attachment arising from the installment of attachment other than the specified attachments.

6-8

6. SPECIFICATIONS

LIFTING CAPACITIES

BELL OVER NOMINELL PASITET FOR NDTERING

KOBELCO CONSTRUCTION MACHINERY CO., LTD E70BSR SKOBREDDE 450 mm

LØFTEPUNKT (AKSE)

HØYDE (m)

6.5

ARM (Se følgende tabell)

BOM (se følgende tabell)

MOTVEKT 843 kg

RBEIDSFORHOLD:

n redskaper (grabb, grave.). m man bearbeider objekter redskapet påmontert, må n av utstyret trekkes fra ne i denne tabellen. utstrakt grabbsylinder. et kompakt eller horisontalt, underlag.

TRYKK I ARBEIDSKRETSEN 29 400 kPa TRYKK I ARBEIDSKRETSEN 29.400 kPa

maskintårnet i fullstendig on

6

ROTASJONSAKSE

ARMSLAG (m) DISSE BELASTNINGENE GJELDER FOR HØYDEN AV OMRÅDET (Z.) FOR ØNSKET ARMSLAG BOMLENGDE 3.84 m ARMLENGDE (m) 1.71

ARMSLAG I m- LASTER I kg (BOMFOTHØYDE) 3.0 4.5 1.5 MAKS REKKEVIDDE ARMSLAG (m) – 2240 1370 – Z2 LD = 1.71 Z1 3090 2170 1190 940(5.43 m)

6-9

6. SPECIFICATIONS

KOBELCO CONSTRUCTION MACHINERY CO., LTD E70BSR SKOBREDDE 450mm

LØFTEPUNKT (AKSE)

ARM (Se følgende tabell)

BOM (se følgende tabell)

MOTVEKT 1 103 kg

RBEIDSFORHOLD:

redskaper (grabb, grave ..). m man bearbeider objekter dskapet påmontert, må av utstyret trekkes fra ne i denne tabellen. utstrakt grabbsylinder. kompakt eller horisontalt, underlag. maskintårnet i fullstendig on

TRYKK I ARBEIDSKRETSEN 29 400 kPa TRYKK I ARBEIDSKRETSEN 29.400 kPa

ROTASJONSAKSE

ARMSLAG (m) DISSE BELASTNINGENE GJELDER FOR HØYDEN AV OMRÅDET (Z.) FOR ØNSKET ARMSLAG BOMLENGDE 3.84 m ARMSLAG I m- LASTER I kg ARMLENGDE (m) 3.0 4.5 1.5 ARMSLAG (m) – 2240 1490 Z2 1.71 LD = 1.71 Z1 3090 2370 1300

6-10

(BOMFOTHØYDE)

MAKS REKKEVIDDE – 1030(5.43 m)

HØYDE (m)

BELL OVER NOMINELL PASITET FOR NDTERING ngre motvektstype)

6. SPECIFICATIONS

KOBELCO CONSTRUCTION MACHINERY CO., LTD E70BSR SKOBREDDE 450mm

LØFTEPUNKT (AKSE)

HØYDE (m)

BELL OVER NOMINELL PASITET FOR NDTERING ngre motvektstype)

ARM (Se følgende tabell)

BOM (se følgende tabell)

MOTVEKT 1 243 kg

RBEIDSFORHOLD:

redskaper (grabb, grave r..). m man bearbeider objekter edskapet påmontert, må n av utstyret trekkes fra ne i denne tabellen. utstrakt grabbsylinder. t kompakt eller horisontalt, underlag. maskintårnet i fullstendig sjon

TRYKK I ARBEIDSKRETSEN 29 400 kPa TRYKK I ARBEIDSKRETSEN 29.400 kPa

ROTASJONSAKSE

6 ARMSLAG (m) DISSE BELASTNINGENE GJELDER FOR HØYDEN AV OMRÅDET (Z.) FOR ØNSKET ARMSLAG BOMLENGDE 3.84 m ARMSLAG I m- LASTER I kg ARMLENGDE (m) 3.0 4.5 1.5 ARMSLAG (m) – 2240 1570 Z2 1.71 LD = 1.71 Z1 3090 2510 1390

6-11

(BOMFOTHØYDE)

MAKS REKKEVIDDE – 1100(5.43 m)

6. SPECIFICATIONS

KOBELCO CONSTRUCTION MACHINERY CO., LTD

BELL OVER NOMINELL PASITET FOR NDTERING ngre motvektstype)

SKOBREDDE 450 mm

LØFTEPUNKT (AKSE)

ARM (Se følgende tabell)

BOM (se følgende tabell)

MOTVEKT 1 503 kg

RBEIDSFORHOLD:

redskaper (grabb, grave ..). m man bearbeider objekter edskapet påmontert, må av utstyret trekkes fra ne i denne tabellen. utstrakt grabbsylinder. kompakt eller horisontalt, underlag. maskintårnet i fullstendig on

TRYKK I ARBEIDSKRETSEN 29 400 kPa TRYKK I ARBEIDSKRETSEN 29.400 kPa

ROTASJONSAKSE

ARMSLAG (m) DISSE BELASTNINGENE GJELDER FOR HØYDEN AV OMRÅDET (Z.) FOR ØNSKET ARMSLAG BOMLENGDE 3.84 m ARMLENGDE (m) 1.71

ARMSLAG I m- LASTER I kg ARMSLAG (m) Z2 LD = 1.71 Z1

1.5 – 3090

3.0 2240 2600

4.5 1680 1500

6-12

(BOMFOTHØYDE)

MAKS REKKEVIDDE – 1190(5.43 m)

HØYDE (m)

E70BSR

7. OPTIONAL EQUIPMENT

7. OPTIONAL EQUIPMENT

7

7-1

7. OPTIONAL EQUIPMENT

7-2

7. OPTIONAL EQUIPMENT

7.1

OPERATION OF HYDRAULIC BREAKER AND NIBBLER

7.1.1

SELECTION OF HYDRAULIC BREAKER AND NIBBLER

When installing a hydraulic breaker or nibbler to the machine, select the optimal breaker or nibbler taking the matters into consideration such as stability, hydraulic system pressure, required hydraulic oil volume.

7.1.2 • •

BEFORE OPERATING BREAKER OR NIBBLER

Consult with your Dealer for the additional piping work and reinforcement for the arm to install the breaker or nibbler to the machine.

When using the breaker or nibbler, fully understand and peruse the operation manual of its manufacturer and the PROHIBITED WORK IN USE OF BREAKER" page 7-8 for the work mentioned in this MANUAL, in order to get full performance of them paying attention to damages on the machine and hydraulic breaker or nibbler.

7.1.3

PRECAUTIONS FOR IMPURITY AND HYDRAULIC OIL

When the hydraulic breaker or nibbler is removed after its installation, apply a blinding plug to the stop valves attached on the tip of arm and openings on the hydraulic pipings for the hydraulic breaker or nibbler to prevent them from invasion of dust, water, etc.

Before the operation, check the looseness on the clamps which are fixing the piping for attachment, and the leakage on connections of tubes and hoses.

7.1.4

SWITCHING SELECTOR VALVE

Be sure to switch selector valve (1) according to the attachment employed.

1

N

B

7

7-3

7. OPTIONAL EQUIPMENT

CAUTION

A. Switching procedure of selector valve 1. Place the attachment to the ground, and stop the engine. Then place the safety lock lever in the "LOCKED" (up) position.

2. Using Allen Wrench (3 mm), loosen and remove bolt (2) on the selector valve section, and turn lever (3) to the position according to the attachment.

3. After positioning of lever (3), using Allen Wrench (3 mm), tighten bolt (2).

N

B

2

3

7-4

7. OPTIONAL EQUIPMENT 7.1.5

SETTING STOP VALVE

Stop valve (1) on arm top end is used to stop hydraulic oil flowing.

Free : Hydraulic oil flows Stop : Hydraulic oil stops flowing Before removing attachment, set stop valve to "STOP" position.

Tools used Stop Valve

Location

Tools

(1)

Arm

Spanner (24 mm)

7

7-5

7. OPTIONAL EQUIPMENT 7.1.6

BASIC OPERATION

A. Breaker and Nibbler Selector Switch Release pedal lock on the right front side of driver&apos;s seat to operate pedal.

C

B

1

1

A

ATTACHMENT OPERATION BY FOOT PEDAL Always check the foot pedal control pattern before operation.

Always read operator's manual before operating machine.

Make sure to set the pedal lock to "LOCKED" position while the breaker or nibbler is not used.

Unexpected contact with "UNLOCKED" position of pedal may cause severe injury or death.

Do not put foot on the pedal except at the time of operation using pedal.

A-1 Pedal locking lever position • Locked position (A) Raise the lever (1) upward, and shift the lever to position (A) to lock the lever.

• When breaker is used: Position (B) In using breaker, set lever (1) to B position (breaker).

• When nibbler is used: Position (C) In using nibbler, set lever (1) to C position (nibbler).

CAUTION

7-6

7. OPTIONAL EQUIPMENT B. Oil flow The relation between the pedal position and the direction of oil flow is shown in right figure.

A

B Nibbler (Crusher) When the toe side (A) of pedal is depressed, oil flows into left piping of attachment. And the heel side (B) of pedal is depressed, oil flows right piping of attachment. (In case of BREAKER, pedal operation is only toe side.)

Breaker

Foot pedal depressing section

Operation

Depress toe section (A) Breaker starts operation Pedal in neutral positon Breaker stops operating Nibbler

Foot pedal depressing section

Operation

Depress toe sectio (A)

Nibbler close

Depress heel section (B)

Nibbler open

7

Do not leave the machine with engine running.

7-7

7. OPTIONAL EQUIPMENT 7.1.7

PROHIBITED WORK IN USE OF BREAKER

The following safety precautions should be used in conjunction with all other safety precautions found in this MANUAL.

Read, understand and follow all safety precautions and operating procedures found in this manual before operating the machine or any attachment.

A. Do Not Use Lewing/Swing Force Do not use the swing force of the machine for pushing or sliding objects. This will cause premature failure of the attachment and other machine components.

B. Do Not Pry and Break Forcibly Do not use the breaker to pry and break rock and concrete. This may damage the hydraulic breaker, and the excavator boom, arm and hydraulic cylinders.

C. Arm In Vertical Position The arm should not be operated in the vertical position to prevent the hydraulic cylinder from vertical shocks.

This may damage the rod seal and piston and cause oil to leak from those sections.

7-8

7. OPTIONAL EQUIPMENT D. Cylinders Do not operate boom, arm or bucket cylinders at stroke ends when using a breaker attachment.

Doing this can cause undue load on the cylinder rods and result in damage.

E. Use for Intended Purpose Use the attachment only for its intended purpose. If not used in accordance with the manufacturers instructions, the excessive pressure exerted on the boom, arm and frame structure of the machine will cause premature failure of the components.

F. Avoid Continuous Operation Operate the nibbler/breaker in 1 minute intervals.

Operation for longer than 1 minute at a time can cause high oil temperatures and the accumulators, cylinder seals and possibly pump damage.

Within One Minute

G. Hose Surge Should the hydraulic hoses begin to surge or vibrate abnormally during operation of a breaker or nibbler, immediately stop operation and contact our dealer/ distributor for assistance.

This problem often is a result of damaged accumulators and can also result in valve failure.

7-9

7

7. OPTIONAL EQUIPMENT H. Do Not Use Dropping Force Do not use the dropping force of the attachment to break or drive objects. This will cause extensive damage to the attachment and machine structure.

I. Do Not Lift Do not use an optional attachment to lift or transport objects or material.

Doing so can cause extensive damage to the attachment, the machine structures or cause injury or death due to slipping or dropping of load due to improper attachment.

J. Do Not Work Underwater The breaker is rusted, and results in damage of sealing.

Consequently contamination with rust, dust and water enter into hydraulic oil. This causes damage of hydraulic equipment.

Do Not Work Underwater

Chisel

K. Working Ranges The balance on the machine becomes unstable at the positions shown in the right figure involving a possibility of turning over the machine. Do not carry out breaker work in this position.

Unacceptable Work Range

Acceptable Work Range

Acceptable Work Range

Unacceptable Work Range

7-10

7. OPTIONAL EQUIPMENT L. Do Not Hit Chisel Against Boom To avoid interference of chisel with boom, operate control lever of arm and boom carefully.

M. Precaution When Lifting Up Machine Press the ground by attachment

Unnecessary machine lifting up is not allowed.

It may cause damage of attachment.

Lift the machine slightly 10~15 cm

7.1.8

PERIODIC INSPECTION AND MAINTENANCE INTERVAL

Contamination and deterioration of hydraulic oil may cause function problems with control valves, early wear and possible seizure of the hydraulic pump leading to break down of the machine hydraulic system.

Operation of breaker accelerates the deterioration of hydraulic oil compared to normal earth moving operation with bucket. Replace filters and hydraulic oil as indicated in following table. Prepare and update a maintenance record following example provided.

Component

Location

Hydraulic oil Return filter element kit (P/No. YR52V01004R400)

7.1.9

Replacement interval First

2nd replacement

Regular

Hydraulic tank

-

-

Every 1000 hours

Hydraulic tank

50 hours

250 hours

250 hours

REINFORCING ATTACHMENT

When operating machine with proper breaker and nibble attached, in case of the arm which is made in factory, reinforcement of arm is not required. But when operated in special application, contact our dealer/distributor.

7-11

7

7. OPTIONAL EQUIPMENT 7.1.10 PROHIBITED WORK IN USE OF NIBBLER The wrong nibbler operating method may cause damage of attachment and excavator or result in dangerous work condition. To prevent these trouble, learn correct and safety operating method. The precaution during operation is explained here with operative examples including similar behavior to prevent trouble.

A. Do Not Strike the Object with Nibbler The hitting and striking the nibbler against object will give undue force to nibbler, machine, boom, arm, link and so on resulting in damage.

B. Do Not Pry and Pull Nibbler during Holding Object Do not pry and pull nibbler which is holding building and structure partly.

C. Do Not Swing the Machine during Holding Object Do not pull down building and structure by the swing force during holding object.

D. Do Not Hold Object Obliquely Select machine position and holding position so that nibbler opening does not hold breaking object obliquely.

7-12

7. OPTIONAL EQUIPMENT E. Do Not Travel while Nibbler is Holding Object Do not pull building and structure by the use of traveling force while nibbler is holding the top side of object.

F. Attention to the Falling Debris Take position to prevent from debris.

The guard (3 faces) is provided for demolition machine.

When standard machine is employed as machine for demolition work, replace the cab with 3 faces protected cab.

G. Cylinder Stroke with Sufficient Allowance When carrying out the demolition work with hydraulic cylinder rod moving to the stroke end, the hydraulic cylinder may be damaged. Do not operate nibbler with hydraulic cylinder rod moving to the stroke end.

Especially the operation of cylinder with the bucket cylinder moved to the stroke end may cause damage of cylinder, link and rod pin.

H. Prohibiting Work Facing Sideways Do not operate the attachment over the sides of the machine. It may cause rollover of machine. And do not operate the machine abruptly but operate it slowly.

7

7-13

7. OPTIONAL EQUIPMENT I. Move Arm Slowly at stroke End of Cylinder When lowering the arm rapidly, and the cylinder rod reaches to stroke end rapidly too, and the impact damages the arm cylinder. Operate the attachment slowly to avoid the abrupt approach to stroke end of arm cylinder.

7.1.11 PRECAUTION TO MANUFACTURES

BE

EXERCISED

ON

BREAKERS

OF

DIFFERENT

There are some differences between manufactures as to the piping to breakers and the handling of breakers. For this reason, consult with the manufacturer when mounting a breakers in the field.

The following is a summary of how breakers should be handled that is extracted from manufacture's catalog use and operation manuals.

This is a general outline of how breakers should be use and may differ with excavator models.

Always contact the breaker manufacture before field mounting.

1. Placing High and Low Pressure Accumulators

2. Standard of Judgment on the Installation of Accumulators High pressureside : Measure the plus oscillation by pressure on the high pressure side of the breaker at the inspection port for the pump's delivery pressure by actuation the breaker at the full revbolution of the engine in mode H and set the maximum pressure difference to within 20 % of the excavator's system pressure 29.4 MPa {300 kgf/cm2 (4,270 psi).

In case it exceeds 20 %, install a high pressure accumulator.

The pulse oscillation is 29.4 MPa {300 kgf/cm2} x 20 % = 5.88 MPa {60 kgf/cm2(850 psi). Therefore, if it is more than this level, and accumulator must be installed.

7-14

7. OPTIONAL EQUIPMENT Install accumulator referring to the result of verification test.

Low pressure side : Measure the inlet pressure of the return filter on the breaker side by actuating the breaker at full engine revolution in the H mode, and in case the maximum pressure exceeds 0.48 MPa {4.9 kgf/cm2} (70 psi), install a low pressure accumulator.

Max. < 0.48 MPa {4.9 kgf/cm2} (70 psi) Regarding the capacity and the charge pressure of accumulators, contact the breaker manufacturer before installation.

3. Installation of a Relief Valve

B de (retur)

7

7-15

7. OPTIONAL EQUIPMENT

7.2

PROPORTIONAL BREAKER)

HAND

CONTROL

(EXTRA,

NIBBLER

AND

To actuate the "extra", operate the switch (1) that is located on left control lever.

And operate the switch (3) that is located on right control lever to actuate the "nibbler (crusher)", and operate the switch (4) to actuate the "breaker".

1

3

4

2

Left Hand Control Lever Switch

Right Hand Control Lever Switch

1

Extra control switch

3

Nibbler (Crusher) control switch

2

Horn switch

4

Breaker control switch

5

Reserve switch

7.2.1

5

BASIC OPERATION

Read, understand and follow all safety precautions and operations found in this manual before operating the machine or any attachment. .

A. Extra Hand Control Slide the switch (1) that is located on left control lever to actuate the "extra operation".

7-16

7. OPTIONAL EQUIPMENT

According to the slide distance of option switch, hydraulic flow rate increases.

B. Horn Switch For the horn switch (2), see "2.3.2.10 HORN SWITCH".

2

C. Nibbler (Crusher) and Breaker Hand Control .

When nibbler (crusher) or breaker is used, refer to the item "ATTACHMENT MODE SELECTION AND SELECTOR VALVE" of "7.1.4 SWITCHING SELECTOR VALVE" C.1 Nibbler Operation Slide the switch (3) that is located on right control lever to open or close the "Nibbler (crusher)".

Do not touch the Breaker switch (button) (4) when you operate Nibbler.

AVOID INJULY OR DEATH Do not leave the machine with engine running.

According to the slide distance of option switch, hydraulic flow rate increases.

7-17

7

7. OPTIONAL EQUIPMENT C.2 Breaker Operating Press the switch (4) that is located on right control lever to operate the "breaker".

1. To operate Breaker, press the switch (4).

Release to stop operation.

2. Operate breaker for 30 seconds then release switch.

3 4

5

The Breaker can be operated by sliding the option switch (3) to the left. But, when you operate the breaker, use the Breaker switch (4) as much as possible.

AVOID INJURY OR DEATH Do not leave the machine with engine running.

D. Reserve Switch When the machine is equipped with the option specification, this switch is used as a reserve switch (5).

7-18

7. OPTIONAL EQUIPMENT

7.3

PROPORTIONAL HAND CONTROL (NIBBLER AND BREAKER)

To actuate the "Nibbler" operate the switch (3) and to actuate the "Breaker" operate the switch (4) that is located on right control lever.

2

3

1

Left Hand Control Lever Switch 1

7.3.1

4

Right Hand Control Lever Switch

Horn switch

2

Nibbler control switch

3

Breaker control switch

4

Reserve switch

BASIC OPERATION

Read, understand and follow all safety precautions and operation procedures found in this manual before operating the machine or any attachment.

Regarding the procedures of nibbler and breaker operation, see "7.2 PROPORTIONAL HAND CONTROL (EXTRA/NIBBLER AND BREAKER)".

7-19

7

7. OPTIONAL EQUIPMENT

7.4

PROPORTIONAL HAND CONTROL (EXTRA)

To actuate the "extra" operate the switch (1) that is located on left control lever.

1

3

2

Left Hand Control Lever Switch 1

Extra control switch

2

Horn switch

7.4.1

Right Hand Control Lever Switch 3

Reserve switch

BASIC OPERATION

Read, understand and follow all safety precautions and operation procedures found in this manual before operating the machine or any attachment.

.

A. Extra Hand Control Slide the switch (1) that is located on left control lever to actuate the "extra operation".

According to the slide distance of option switch, hydraulic flow rate increases.

7-20

7. OPTIONAL EQUIPMENT B. Horn Switch For horn switch (2), see "2.3.2.10 HORN SWITCH".

C. Reserve Switch When the machine is equipped with the option specification, this switch is used as a reserve switch (5).

7

7-21

7. OPTIONAL EQUIPMENT

7.5

OBJECTS HANDLING

7.5.1

SAFETY PRECAUTIONS

A. SAFETY LOADS LIFTING •

•

• • •

• • • •

The excavator is a machine designed specifically to perform digging/loading works, thus it must not be used to handle suspended loads. In the event, under exceptional conditions, it becomes necessary to handle materials, the following indications must be strictly implemented: The machine must be equipped compulsorily with the appropriate variant provided upon request. Also, totally comply with the safety precautions for the operation of the excavator as a lifting equipment.

Secure the loads to be raised using cables or chains fastened with appropriate hooking mechanisms.

Do not hook cables or chains to the bucket teeth.

Nobody should be allowed to remain under the raised load or within the excavator operating range for any reason whatever.

Do not exceed specified lifting capacity. Incorrect fastening of slings or chains may cause boom/arm failure or failure of the lifting means with consequent bodily injuries and even death.

Always ensure that slings and chains used for lifting are adequate to the load and in good condition.

All lifting capacities are referred to the machine on a level surface and should be disregarded when working on a slope.

In any case, comply with the current national or local regulations on this matter.

7-22

7. OPTIONAL EQUIPMENT 7.5.2

OBJECTS HANDLING OPERATION

The machine has been specifically designed to perform digging/loading works. The handling of suspended loads completing the digging cycle is allowed, providing that the machine is equipped with the appropriate variant supplied upon request. Handle suspended loads, following strictly all current regulations regarding this matter, as well as the rules described in the "SAFETY PRECAUTIONS" chapter.

The anti-drop valves located on the cylinders, the warning buzzer device, the table of the loads that can be lifted located in the cab and the hook on the link of the bucket linkage are SAFETY DEVICES, making part of the suspended load handling variant. The lack of one of them or a damaged item make the machine unfit for works handling suspended loads.

To handle suspended loads, act as described here below:

Prior to starting any handling of suspended loads, check that the valves do not show clear evidence of damages or abnormal noises. In the event abnormal conditions are found, it is necessary to contact a Dealer; in the meantime, do not use the machine for the handling of suspended loads.

Check that the lifting devices (hooks, chains etc.) are in perfect conditions without any sign of excessive wear.

In any case, comply with current regulations in effect for these devices (non supplied with the machine).

In order to prevent injuries, do not exceed the nominal load capacity of the machine. If the machine is not on a flat surface, the load capacity is reduced. In any event, proceed always with extreme care.

1. Set an engine speed appropriate for the hydraulic load required.

2. Evaluate (if known) the mass of the object to be handled and compare it with the data listed in the table located in the cab.

Do not lift loads exceeding the maximum values prescribed by the table.

3. Prior to performing lifting operations, press switch (1) to activate the load-momentum sensor. This sensor, once the safety limit is reached, activates the sound warning device.

4. Secure the load with the appropriate hook (2) located on the bucket linkage rod, using slinging devices and chains adequate for the load to be lifted.

Check that the lifting devices (hooks, chains etc.) are safe and free from signs of excessive wear. In any case, comply with current regulations relative to the inspection of such devices (not provided with the machine).

The device can be used exclusively for the lifting of parts not placed on the ground. Do not use it for towing operations, uprooting or tearing apart.

7-23

7

7. OPTIONAL EQUIPMENT 5. In order to limit the swinging of the load, avoid slinging it with cables and/or chains too long.

6. Check the surrounding working area and make sure that the path to be travelled with the load is free from obstacles.

7. Lift slowly the load, avoiding sharp movements which could cause swinging of the load. Keep the load near the machine, to improve the stability and operate, preferably, along its longitudinal axis, rather than crossways. Lift the load from the ground the minimum height required.

8. Position and place the load where desired, making sure that it is resting on a solid base appropriate for its mass.

9. Remove the chains.

2

Suspended load can swing and rotate in all directions, thus there is the dangerous possibility that they can hit persons or the cab of the machine. In order to limit this danger, it is absolutely required that all bystanders are moved away from the field of action of the machine and that the load is handled slowly. In the event the load rotates or swings during the handling, slow-down until stopped and lower it slowly to the ground; then correct the way it is slung.

In the event the sound alarm is activated during the handling of the load, place the load onto the ground and check the load conditions making reference to the appropriate table in the cab.

7-24

7. OPTIONAL EQUIPMENT 7.5.3

1.

2.

3.

4.

5.

6.

7.

8.

DIAGRAM FOR THE READINGS OF THE LIFTABLE LOADS, LOCATED INSIDE THE CAB

Boom length.

"LD" length of second alternative arm.

Distance of the load from the swing center line.

Maximum liftable load in tons, at the tilting limit, in accordance with standard ISO 10567 (75% stability, 87% hydraulic system).

Maximum liftable loads in tons, at the maximum distance from the swing center line.

Maximum working distance from the swing center line.

Counterweight.

Setting pressure of main pressure relief valve/safety valves of the hydraulic system.

(2) (1) (7)

(8)

(1) (2)

(3)

(5) (4)

(6)

7

7-25

7. OPTIONAL EQUIPMENT

7-26

8. SPECIAL PROCEDURES

8

8. SPECIAL PROCEDURES

8-1

8. SPECIAL PROCEDURES

8-2

8. SPECIAL PROCEDURES

8.1

GENERAL

The E70BSR machine incorporates automatically applied spring brake systems in the travel motors and swing motors. These systems will automatically engage the brakes when engine is stopped making it impossible to move the machine.

This section contains the required procedures for releasing the travel motor brakes, the swing motor brake and lowering the attachment to the ground should sudden engine failure be experienced.

Make certain chock blocks are secure at front and rear of each track before attempting to release brakes.

Never stand in the path of the tracks when releasing brakes.

Read, understand and follow all safety precautions and procedures found in this manual before attempting any operation, inspection, maintenance or repair of this machine, attachment or any of its systems.

The procedures found in this section should be performed by a well trained experienced service technician who is familiar with the E70BSR machines.

8-3

8

8. SPECIAL PROCEDURES

8.2

RELEASING TRAVEL MOTOR BRAKES

A. Tools and Equipment Required

Attachment on Ground

Star ter ke Starter kkey ey switch switch in "OFF" position

Chock blocks at front and rear of each track

Throttle in "LO" position

Fig. 8-2

Fig. 8-1 1. Four chock blocks.

2. One 5 mm allen wrench.

3. One 8 mm allen wrench.

4. With 10 mm socket wrench.

5. Two 4 liter (1.1 Gal) capacity drain pans.

6. One M8-1.25 x 15 mm lifting eyes.

7. Overhead lifting device capable of lifting and holding 45 kg (100 lb).

8. Torque wrench 70 to 74 N-m {52 to 55 lbf-ft} capacity or better.

9. Thread sealant (For drain and check/fill plugs).

10.Rubber or soft faced mallet.

8-4

8. SPECIAL PROCEDURES B. Procedures

8

Remove drain plug with 10 mm socket wrench

Remove 12 mounting bolts with 5 mm socket wrench

1.35 liter (0.4 gal) capacity drain pan

Fig. 8-3

Fig. 8-4

1. Place chock blocks at front and rear of each track to prevent machine from moving when brakes are released.

See Fig.8-1.

2. Lower attachment to ground. See "8.4 LOWERING ATTACHMENT WHEN SUDDEN ENGINE FAILURE OCCURS" for proper procedures.

3. Turn key switch "OFF" and remove key. See Fig. 8-2.

4. Remove check/fill plug from each travel motor using the 10 mm socket head wrench. See Fig. 8-3.

5. Place a clean 4 liter (1.1 Gal) capacity drain pan under each travel motor drain plug and remove drain plug using the 10 mm socket head wrench. See Fig. 8-3.

6. After all of the gear oil has drained, cover the drain pans to prevent contamination and move them to an area away from the machine.

7. Remove the fifteen plate mounting bolts from the travel motor reduction unit cover plates. See Fig. 8-4.

8. Remove the covers from both travel reduction units to expose the planetary gears. See Fig. 8-4.

9. Remove the thrustplate and sun gear. See Fig. 8-5.

10.Carefully remove "Sun gear" from the planetary gear assembly by hand and lay it aside. See Fig. 8-5.

11. Remove the thrustplate and sun gear. See Fig. 8-5.

12.Carefully remove "Sun gear" from the planetary gear assembly by hand and lay it aside. See Fig. 85.

13.Install cover plates onto housings and tighten all bolts securely.

SUN GEAR

Fig. 8-5

-Be careful not to damage lip of cover plate. Any damage to the lip could result in a gear oil leak.

-When removing the following components it will be necessary to have a clean area free of dirt and grit to lay these components.

8-5

8. SPECIAL PROCEDURES 14.Install fill and drain plugs into cover plates and re&ndash;place gear oil into travel reduction units through fill / check port to proper level.

15.After steps 4 through 12 have been performed on both travel reduction units, the machine may be towed to an area where repairs can be made.

16.After repairs are made reinstall the "Drive Gear" in reverse order. Use the following torque specifications for bolts and plugs.

Fig. 8-6

TORQUE SPECIFICATIONS COVER BOLTS (M6).........13.7 PLUGS...............................49.0 THRUST PLATE BOLTS...35.3

1.0 N.m {10.1 0.7 lbf.ft} . {72.3 14.5 lbf.ft} 4.9 N.m 2.0 N.m {26 1.5 lbf.ft}

8-6

8. SPECIAL PROCEDURES

8.3

RELEASING SWING BRAKE

8 Make certain that the attachment is on the ground to help prevent sudden rotation of the upper structure before attempting to release the swing brake.

Refer to page 8.12 for attachment lowering procedures.

We highly recommends the use of a hydraulic hand pump to release the swing brake manually when the engines fails to start. Refer the Fig. 8-8 to use the proper fitting connector on P port. Remove the hose and install the proper connector on P port. Install the hydraulic hand pump and apply hydraulic pressure as follows: E70BSR ... 29 Mpa {413 psi}

Remove all hoses, tubes and fittings to gain access

Fig. 8-7

TOP VIEW

SWING MOTOR

B

SIDE VIEW

A

P

Mu

SGo Torque Remarks N·m {lbf·ft} 2-PF1/2 108 10 {80 7} A,B Main port PF3/4 162 15 {120 11} Mu Make-up port Drain port 73.5 5 {54 3.7} PF3/8 Dr Brake release port PF1/4 36.3 2 {27 1.5} P 9.8 {7.2} SGo Gear oil filling port PT1/2 GA PRESSURE MEASUREMENT PT1/4 GB PORTS

Code

Dr

Fig. 8-8

8-7

Name

Size

8. SPECIAL PROCEDURES

In highly contaminated environments it is recommended to remove the whole swing motor assembly, if a hydraulic hand pump is not available. Refer to the shop manual for special instructions or contact your distributor for assistance. When the swing motor is removed, make sure to use caps and plugs on hoses, tubes and fittings to protect the hydraulic system from any contamination. Also, a cover must be used to protect the swing reduction unit. If this approach is taken, and the swing reduction unit becomes contaminated, make sure to flush and clean the swing reduction unit. Refer to page 4-11 for proper oil and component capacity.

If a hydraulic hand pump is not available, and the contamination can be controlled easily, then proceed to the next page for specific instructions on a different alternative to release the swing parking brake.

Use safety protection such as: hard hat, working gloves, safety shoes and safety glasses when needed to perform this job.

A. 1.

2.

3.

4.

5.

6.

7.

Tools and Equipment Required Handtools required for removal of hydraulic tubes, hoses and fittings.

Plugs and caps for tubes, hoses and fittings.

10 mm allen wrench.

Lifting eye. P/No. ZE72X12000 Overhead lifting device capable of lifting and holding 45 kg (100 lb) Plenty of clean, dry shop rags and/or paper towels.

Plenty of clean, dry shop rags and/or paper towels.

8-8

8. SPECIAL PROCEDURES B. Procedures 1. Lower attachment to ground. Refer to previous page for proper procedures in lowering the attachment.

2. Remove all hoses and tubes from the swing motor top plate and swing valve to gain access to the top plate mounting bolts. See Fig. 8-7.

3. Install the proper plugs and caps onto hoses, tubes and fittings to avoid the possibility of contamination entering the hydraulic system. See Fig. 8-9.

8 Install proper caps and plugs on hoses, tubes and fittings to help prevent contamination entering the system

Fig. 8-9

Use only plugs and caps designed to properly seal the specific hose, tube or fitting they are to be installed on.

M12 x 30

Lifting position Remove (4) cover mounging bolt

Top cover

Fig. 8-10

Fig. 8-11

4. Loosen the four top plate mounting bolts with the 10 mm allen wrench. See Fig. 8-11.

5. Install eye bolts as indicated in Fig. 8-10, and install P/No. ZE72X12000 eye bolts.

6. Remove two top plate mounting bolts from corners opposite of each other.

Place a large quantity of clean, dry shop rags around the swing motor to help catch any overflow of hydraulic oil from the removal of the top plate.

7. Attach overhead lifting device to the lifting eyes and remove most of the slack from the cable or chain.

8. Carefully remove the remaining two bolts from the top mounting plate.

9. Using the overhead lifting device, carefully lift the swing motor top cover with swing shockless valve assembly and away from the swing motor.

The top plate will raise from spring pressure as the last two bolts are removed. Some movement of the upper frame may be experienced as the spring tension is released.

8-9

8. SPECIAL PROCEDURES

Do not allow any dirt or debris to enter the swing motor or settle on the top plate.

Remove all springs

Align distributor plate holes towards front and rear of housing

Fig. 8-12

Fig. 8-13

10.Carefully remove all brake springs and place in a container filled with fresh, clean hydraulic oil. Then, seal the container to prevent contamination. See Fig. 8-12.

11. Align the holes of the distributor plate in the swing motor until they are located toward the front and back of the swing motor housing. See Fig. 8-13.

12.Carefully place the top plate over the swing motor and align the dowel pins of the top plate with the holes in the distributor plate. See Fig. 8-14.

13.Carefully and slowly lower the top plate into position on the swing motor and install, by hand, the four top plate mounting bolts.

14.After the machine upper structure is positioned for towing, remove cover again and reinstall the swing brake springs. Repeat steps 11~13 to lock the upper frame into position for proper transportation.

Dowel pins

Fig. 8-14

Make certain the top plate dowel pins and the distributor plate holes mesh together.

Avoid oil spills. Use containers, rags, and / or paper towels to contain any oil leakage. Dispose all waste oils, fluids lubricants and other hazardous waste properly, according to government regulations.

8-10

8. SPECIAL PROCEDURES

8.4

LOWERING OCCURS

ATTACHMENT

WHEN

SUDDEN

ENGINE

FAILURE

8

A. How to Lower Attachment - Fig. 8-15

When you need to lower the attachment in an emergency, handle the holding valve at first, secondly loosen the port relief valve of the main control valve.

When engine stops because of troubles, the relief valve incorporated in the holding valve mounted on the boom cylinder head side is available to lower attachment.

Be careful when lowering attachment. Do not stand under boom.

MANUAL OPERATION FOR THE RELIEVING OF HOLDING VALVE 1. Loosen the lock nut (1).

2. Rotate the thread (2) four turns clockwise to tighten, and the inner spool valve is switched.

Consequently, the holding valve is relieved forcibly.

3. To return to the active state of the holding valve, rotate the thread (2) counterclockwise fully to the end. And tighten the lock nut (1).

(1): LOCK NUT (2): THREAD FOR MANUAL OPERATION

Holdeventil

1

Fig. 8-15

8-11

2

8. SPECIAL PROCEDURES B. Emergency Manual Valve for Lowing Attachment - Fig. 8-16 Reducing valve assembly emergency manual valve for lowing attachment is equipped internally between B5 port of boom cylinder head side and boom lock valve. For safety, this valve lowers rifted attachment to the ground, if the machine stops with engine trouble. Only in case that boom is lowering, the pressure in the cylinder of attachment can be released by operating arm or bucket control lever.

1. Functional Explanation In normal cases, this valve was blocked completely to prevent pressure leak of boom circuit. a. Lowering of Boom Loosen lock nut at first and loosen the lock screw to the end of contact.

This valve is provided the mechanism of stopper against falling out. But the mechanism might cause break by undue force.

The oil of boom cylinder head side flows into drain passage through orifice, and boom lowers slowly. The time of boom lowering to the ground takes about 4 to 8 minutes in accordance with machine position and holding pressure. b. Function of Actuator Oil pressure of PC port is reduced by releasing holding pressure of boom cylinder head side to drain passage through orifice.

Operation of actuator with remote control valve is possible by leading medium pressure via orifice from PC port to shuttle valve. In this function, this leading of medium pressure ensures primary pressure of remote control (source of pressure). This function ensures that the cylinder movement of boom, arm, bucket and others can be actuated only downward by self weight. Consequently the releasing of pressure becomes possible.

But after attachment is lowered to the ground by lowering boom, holding pressure disappears and remote valve is possible.

When the boom cylinder has holding valve, loosen above-mentioned reducing valve assembly together with port relief valve of holding valve, the boom cylinder starts boom lowering.

Spool of holding valve moves to open side by back pressure of port relief valve, and holding pressure of boom cylinder is led to "Emergency Manual Valve for Lowing Attachment - Fig. 8-16" operation of actuator by remote is possible.

8-12

8. SPECIAL PROCEDURES

8

Maskinens front

Manuell nødventil

4

2

1

3

Fjernstyrt ventil (PC-port) Bomhodetrykk (B5 port)

Fig. 8-16 Emergency manual valve

8-13

8. SPECIAL PROCEDURES

8.5

HYDRAULIC TANK PRESSURE

How to release air pressure remaining in the hydraulic tank.

After engine stops, the air pressure remaining in the hydraulic tank.

Can be released by pushing valve on the air breather rubber cap several times (5 to 7 times). Air breather mounted on the upper part of hydraulic tank.

8-14

Push Valve

DECLARATION OF CONFORMITY

EC DECLARATION OF CONFORMITY The p age tha t follows co ntains a copy of the EC declaration of conformity.

The Ma nufacturer declar es tha t the machin e ha s been de signed a nd constructed in conformity with European Dire ctives a nd amendments and the decrees and regulations governed by national laws.

The or iginal de claration of co nformity is su pplied with each machine. Keep the original copy in a safe place. The local a uthorities may as k for t his document to be presented in or der to check the conformity of your machine.

There is a translation of the declaration on the back of the original copy in the language of the country in which the machin e is used . The re a re so me additional notes for greater clarity: 1. The main s afety component s fitt ed and supplied with the machine are liste d in poin t 1.2. Oth ers, such as the var iant for m oving suspended loads or th e ca b fron t protection, are available on request by the customer.

2. Point 2 contains all the information required by the CE Acou stic e mission directive 2000/14/ EC. Refer to the original copy for specific information on th e e quipment. T his p age also contains in formation relating to the a coustic pressure leve l in the driver’s sea t (LpA) ( page 1-14), which is no t the subje ct of the above mentioned EC d irective an d th erefore no t contained in it.

3. General re gistration num ber fo r this type of equipment. Th e sequence of le tters a nd numbers may var y de pending on the configuration of the equipment.

4. Registration n umber of the de claration o f conformity. Refer to th is number wh en information or assistance is requested from the manufacturer a bout th e declaration of conformity.

5. Signature of a pe rson authorised to sig n the document on behalf of the company.

nf767 .001.3.0.2009.12.11.NALA00000

NEW HOLLAND KOBELCO CONSTRUCTION MACHINERY S.p.A. Strada Settimo, 323 - I-10099 S. Mauro Torinese (Torino) - Italia

DICHIARAZIONE "CE" DI CONFORMITÀ "EC" DECLARATION OF CONFORMITY

Il sottoscritto dichiara che la sottoindicata macchina è stata progettata e costruita in conformità alle seguenti Direttive Europee, come emendate, e ai decreti e regolamenti che le traspongono nelle leggi nazionali: The undersigned declare that the machine described below has been designed and manufactured in compliance with the following European Directives, as amended, and the regulations transposing them into national laws:

1. 2006/42/CE "Sicurezza delle macchine" 1.1 Norme europee armonizzate nel cui rispetto la conformità è dichiarata: EN 474-1:2006+A1:2009; European Harmonised standards under which conformity is declared: EN 474-5:2006+A1:2009 1.2 Principali componenti di sicurezza montati e forniti con la macchina Sì

Yes

Main safety components installed and supplied with the machine

1

1.2.1 Struttura di protezione contro la caduta di oggetti (F.O.P.S.)

No No

Falling Object Protective Structure (F.O.P.S.)

1.2.2 Variante per la movimentazione dei carichi sospesi (EN 474-5 §5.6.4; EN 474-1 Annex E) Object handling application kit (EN 474-5 §5.6.4; EN 474-1 Annex E)

1.2.3 Struttura di protezione in caso di ribaltamento (R.O.P.S.) Roll Over Protective Structure (R.O.P.S.)

1.2.4 Protezione frontale cabina Cab front guard

1.2.7 # # # 1.4 Nome ed indirizzo della persona autorizzata a costituire il fascicolo tecnico: Name and address of the person authorised to compile the technical file:

New Holland Kobelco C.M. S.p.A. Strada Settimo, 323 – 10099 S. Mauro, Italy 2. 2000/14/CE "Emissione acustica" 2.1 Procedura di valutazione della conformità seguita: Allegato XXXXXXXXXX Conformity assessment procedure followed:

2.2 Nome e indirizzo dell’Organismo Notificato coinvolto: XXXXXXXXXX Name and address of the Notified Body involved:

2.3 Livello di potenza sonora misurato LWA (rif. 1 pW):

0 dB(A)

Measured sound power level LWA (ref. 1 pW):

2.4 Livello di potenza sonora garantito LWA (rif. 1 pW):

2

Guaranteed sound power level LWA (ref. 1 pW):

2.5 Potenza motore (come definita dalla ISO 14396):

0 dB(A) 0 kW

Engine power (as defined by ISO 14396):

2.6 Detentore della documentazione tecnica: XXXXXXXXXX Holder of the technical documentation:

3. 2004/108/CE "Compatibilità Elettromagnetica" 3.1 Norme europee armonizzate nel cui rispetto la conformità è dichiarata: EN 13309:2000 European Harmonised standards under which conformity is declared:

4. Altre Direttive applicabili: Other applicable Directive/s:

5. Costruttore:

NEW HOLLAND KOBELCO C.M. S.p.A.

Manufacturer:

7. Tipo: Type:

### 6. Categoria: Category:

E70BSR

8. Matricola: Serial n.:

Escavatore idraulico

Hydraulic excavator

YT0699999

3

4 NALA00000 San Mauro Torinese, Italia, 29/12/2009

Signature (name and function)

5