New Holland E215C EVO Crawler Excavator Operator's Manual 48016681 - PDF DOWNLOAD

OPERATOR’S MANUAL E215C EVO

Crawler Excavator

Part number 48016681 1st edition English June 2016

Contents 1 GENERAL INFORMATION Note to the Owner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Intended use. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Electro-Magnetic Compatibility (EMC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Product identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Operator's manual storage on the machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Machine orientation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Machine components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-1 1-2 1-2 1-3 1-5 1-5 1-6

2 SAFETY INFORMATION Safety rules and signal word definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 Safety rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 Ecology and the environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10 Hand signals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11 Safety signs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-15

3 CONTROLS AND INSTRUMENTS Access to operator's platform Frame - Access/Exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1 Position of the operator’s compartment controls and accessories . . . . . . . . . . . . . . . . . . . . . 3-3

Operator's seat Mechanical suspension seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5 Air suspension seat (option) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9

Forward controls Hand control levers and pedals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Windshield . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Front lower window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Front right-hand console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

System display and function control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Monitor switches. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Menu screen display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Clock adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-13 3-17 3-18 3-19 3-20 3-25 3-27 3-37

Left-hand side controls Left-hand control arm. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Gate lock lever and safety bar. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Heating, ventilation or air-conditioning control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Cab internal lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Emergency exit hammer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Sliding windows on door. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-38 3-40 3-41 3-45 3-46 3-46

Right-hand side controls Right-hand control arm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Cab radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Right-hand console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Cup holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-47 3-49 3-52 3-53

Rearward controls Fuse box. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Magazine rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Refrigerated/heated compartment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Storage compartment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Coat hanger hook . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-54 3-54 3-55 3-55 3-56

Overhead controls Roof curtain. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-57 Roof hatch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-57 Sun shield (optional). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-57

Exterior controls Fuel tank. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Rear view mirrors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Rear view camera (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Front storage box. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Side doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Battery master switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Engine hood . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Lower panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Windshield washer reservoir . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Safety valves (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Optional tool supply valves (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Fuel tank filler pump (if equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-58 3-59 3-62 3-62 3-63 3-64 3-65 3-66 3-66 3-67 3-67 3-68

4 OPERATING INSTRUCTIONS Commissioning the unit Cab - Operating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1 Break-in period . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3

Starting the unit Anti-theft protection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4 Starting the engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7 Bringing the machine up to operating temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9 Engine operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10 Operating the machine in hot or cold weather. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11 Machine operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-12

Stopping the unit Stopping the engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13

Moving the unit Machine travel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Handling the machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Load handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Operating the machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Lowering the attachment in the event of a failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Auxiliary hydraulic circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4-14 4-17 4-19 4-21 4-23 4-24

Parking the unit Parking the machine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-29

5 TRANSPORT OPERATIONS Shipping transport Loading the machine onto a transport trailer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1 Tie downs for shipping. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4 Unloading the machine from a transport trailer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6

Recovery transport Towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7

6 MAINTENANCE General information Basic instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1 Fluids and lubricants . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4 Engine oil recommended operating temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8 Releasing pressure in the hydraulic system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9 Grease points. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-11 Levels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-19 Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-21 Cooling system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-24 Fuel system. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-28 Hydraulic circuit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-36 Air filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-45 Swing reduction gear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-49 Travel reduction gears. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-51 Tracks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-52 Track rollers and idler wheels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-55 Radiator and coolers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-56 Fan and alternator drive belt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-58 Adjustment of engine valve rocker clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-60 Fuel tank filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-60 Fire extinguisher (not supplied) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-60 Protecting the Electrical/Electronic Systems During Charging or Welding . . . . . . . . . . . . 6-61

Machine inspection and cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Checking the machine settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Plastic and resin parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Checking the cylinders for leaks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Tooth tip wear limits on the backhoe bucket. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Replacing a backhoe bucket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Air conditioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Gas spring inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Torque specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Alternator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Starter motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Bulb replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-62 6-62 6-62 6-63 6-64 6-65 6-67 6-71 6-72 6-73 6-75 6-79 6-80 6-81

Maintenance planning Maintenance chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-84

Storage Preparing for storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-87 Periodic checks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-88 Starting up after storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-89

7 TROUBLESHOOTING Fault code resolution Engine troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1

8 SPECIFICATIONS Machine specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1 Fluids and lubricants . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-4 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-8 Weights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10

9 ACCESSORIES Direct fit buckets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1

1 - GENERAL INFORMATION

1 - GENERAL INFORMATION###_1_### Note to the Owner Improper operation of this machine can cause injury or death. Before using this machine, make certain that every operator: • Is instructed in safe and proper use of the machine.

• Reads and understands the Manual(s) pertaining to the machine.

• Reads and understands ALL Safety Decals on the machine.

• Clears the area of other persons.

• Learns and practices safe use of machine controls in a safe, clear area before operating this machine on a job site.

It is your responsibility to observe pertinent laws and regulations and follow NEW HOLLAND CONSTRUCTION instructions on machine operation and maintenance.

Your machine has been designed and built to the highest standards of quality. It conforms to all current safety regulations. However, the risk of accidents can never be completely excluded. That is why it is essential to observe elementary safety rules and precautions.

Read this manual carefully, paying particular attention to the instructions concerning safety, operation and maintenance so as to avoid the risk of injury while operating or servicing the machine.

The standard attachments and tools of this machine are designed to carry out all kinds of earthmoving and rehandling operations. If you want to use this machine to handle a load (pipes, culverts, formwork, etc.), make sure that it is designed to carry out this kind of work. For this type of application, the machine must be equipped with safety valves, a load handling chart corresponding to the type of machine and its attachment and a load fixing point. All legal requirements must also be strictly observed.

Do not use this machine for any application or purpose other than those described in this manual. If the machine is to be used for work involving the use of special attachments, accessories or equipment, consult your NEW HOLLAND CONSTRUCTION Dealer in order to make sure that any adaptations or modifications made are in keeping with the machine's technical specifications and with prevailing safety requirements.

Any modification or adaptation which is not approved by the manufacturer may invalidate the machine's initial conformity with safety requirements.

The machine must undergo regular inspections, the frequency of which varies according to the type of use. Consult your NEW HOLLAND CONSTRUCTION Dealer.

NOTICE: The engine and fuel system on your machine is designed and built to government emissions standards.

Tampering by dealers, customers, operators and users is STRICTLY PROHIBITED BY LAW. Failure to comply could result in government fines, rework charges, invalid warranty, legal action and possible confiscation of the machine until rework to original condition is completed. Engine service and/or repairs must be done by a certified technician only.

Your NEW HOLLAND CONSTRUCTION Dealer is at your disposal for any further information. He will also provide any after-sales service you may require, and genuine NEW HOLLAND CONSTRUCTION spare parts, your guarantee of quality and match.

You can obtain manuals on the operation, maintenance and repair of your machine from your NEW HOLLAND CONSTRUCTION Dealer. To ensure quick and efficient service, consult your NEW HOLLAND CONSTRUCTION Dealer for assistance in ordering the correct manuals for your machine.

Your NEW HOLLAND CONSTRUCTION Dealer can provide after-sales service and genuine NEW HOLLAND CONSTRUCTION spare parts, your guarantee of quality and match.

CNH Industrial America LLC. Company reserves the right to make changes in the specification and design of the machine without prior notice and without incurring any obligation to modify units previously sold.

The description of the models shown in this manual has been made in accordance with the technical specifications known as of the date of design of this document.

1-1

1 - GENERAL INFORMATION

All data given in this manual is subject to production variations. Dimensions and weights are provided with approximate values and the machine fitting shown in the illustrations may not correspond with standard models. For precise information on specific machine models and versions, please consult your NEW HOLLAND CONSTRUCTION Dealer.

Reproduction or translation, even partial, is prohibited without written authorization from CNH Industrial America LLC. Company.

Intended use NOTICE: do not use the excavator for operations which are foreign to its specifications and not included in this manual in order to prevent serious injury to persons or damage to the machine. The manufacturer/dealer is not responsible for damage caused by improper use.

The excavator has been designed to carry out digging and earth moving operations through the use of a bucket.

Operations that involve the use of hydraulic hammers are also possible. Other operations, such as moving suspended loads, are only possible if the specific variant approved by the manufacturer is present.

Using the excavator and its equipment for different operations, such as towing, transporting and lifting people, is considered inappropriate and is prohibited.

Electro-Magnetic Compatibility (EMC) Interference may arise as a result of add‐on equipment that may not necessarily meet the required standards. As such interference can result in serious malfunction of the unit and/or create unsafe situations, you must observe the following: • The maximum power of emission equipment (radio, telephones, etc.) must not exceed the limits imposed by the national authorities of the country where you use the machine • The electro‐magnetic field generated by the add‐on system should not exceed 24 V/m at any time and at any location in the proximity of electronic components • The add‐on equipment must not interfere with the functioning of the on board electronics Failure to comply with these rules will render the NEW HOLLAND CONSTRUCTION warranty null and void.

1-2

1 - GENERAL INFORMATION

Product identification The E215C EVO LC is a totally hydraulic excavator. It consists of an undercarriage fitted with tracks and a turntable bearing which supports the upper structure frame. The upper structure frame supports the attachment, at the front end of the machine, plus the engine, hydraulics and cab. When the operator works the controls, the engine-driven pump delivers hydraulic fluid to the control valves. The control valves distribute the hydraulic fluid to the various cylinders and hydraulic motors employed. A cooling system maintains the hydraulic fluid at normal operating temperature.

SMIL16CEX1050AA

1

When ordering parts, obtaining information or assistance, always supply your NEW HOLLAND CONSTRUCTION Dealer with the type and serial number of your machine or accessories.

Write the following in the spaces below: the type, serial number and year of manufacture of your machine, accessories and the serial numbers of the various hydraulic and mechanical components.

Machine (1) Type / Model and Category: (Hydraulic Excavator) E215C EVO LC. (2) Product identification number:

SMIL16CEX0679AA

1-3

2

1 - GENERAL INFORMATION

Engine Make and type: ISUZU GI - 4HK1X Serial number: NOTICE: The engine and fuel system on your machine is designed and built to government emissions standards.

Tampering by dealers, customers, operators and users is STRICTLY PROHIBITED BY LAW. Failure to comply could result in government fines, rework charges, invalid warranty, legal action and possible confiscation of the machine until rework to original condition is completed. Engine service and/or repairs must be done by a certified technician only.

F77BYM-002

Component serial numbers Hydraulic pump: Swing reduction gear: Travel reduction gears: Travel control valve: Attachment control valve: Swing control valve:

1-4

3

1 - GENERAL INFORMATION

Operator's manual storage on the machine Always keep the manual in the location provided for that purpose (behind the operator’s seat). Make sure it is always complete and in good condition. If you wish to obtain extra copies, or copies in languages other than that of the country of use, consult your NEW HOLLAND CONSTRUCTION Dealer.

YLNR3P-002

1

Machine orientation The terms "Right-hand", "Left-hand", "Front" and "Rear" are used in this manual to indicate the sides as they are seen from the operator's seat when the cab is over the idler wheels.

NOTICE: the illustration opposite shows the machine in normal travel position. In normal travel position, the cab is over the idler wheels. The travel reduction gears are at the rear of the upper structure.

(A) Front (B) Rear (C) Right-hand side (D) Left-hand side (E) Travel motors (F) Idler wheels

726B3831

1-5

1

1 - GENERAL INFORMATION

Machine components

1

ABAFE006

1.

Backhoe bucket

13. Hydraulic pump

2.

Connecting rod

14. Engine compartment

3.

Yokes

15. Counterweight

4.

Backhoe bucket cylinder

16. Air filter

5.

Arm

17. Batteries

6.

Arm cylinder

18. Tracks

7.

Boom

19. Travel reduction gears

8.

Boom cylinders

20. Lower rollers

9.

Swing reduction gear

21. Upper rollers

10. Fuel tank

22. Tension shock absorbers

11. Hydraulic reservoir

23. Idler wheels

12. Control valve

24. Cab/Operator's compartment 25. Swing components

1-6

2 - SAFETY INFORMATION

2 - SAFETY INFORMATION###_2_### Safety rules and signal word definitions Personal safety This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible death or injury.

Throughout this manual you will find the signal words DANGER, WARNING, and CAUTION followed by special instructions. These precautions are intended for the personal safety of you and those working with you.

Read and understand all the safety messages in this manual before you operate or service the machine.

DANGER indicates a hazardous situation that, if not avoided, will result in death or serious injury.

WARNING indicates a hazardous situation that, if not avoided, could result in death or serious injury.

CAUTION indicates a hazardous situation that, if not avoided, could result in minor or moderate injury.

FAILURE TO FOLLOW DANGER, WARNING, AND CAUTION MESSAGES COULD RESULT IN DEATH OR SERIOUS INJURY. Machine safety NOTICE: Notice indicates a situation that, if not avoided, could result in machine or property damage.

Throughout this manual you will find the signal word Notice followed by special instructions to prevent machine or property damage. The word Notice is used to address practices not related to personal safety.

Information NOTE: Note indicates additional information that clarifies steps, procedures, or other information in this manual.

Throughout this manual you will find the word Note followed by additional information about a step, procedure, or other information in the manual. The word Note is not intended to address personal safety or property damage.

2-1

2 - SAFETY INFORMATION

Safety rules General safety rules Use caution when you operate the machine on slopes.

Raised equipment, full tanks and other loads will change the center of gravity of the machine. The machine can tip or roll over when near ditches and embankments or uneven surfaces.

Make sure that all guards and shields are in good condition and properly installed before you operate the machine. Never operate the machine with shields removed.

Always close access doors or panels before you operate the machine.

Never permit anyone other than the operator to ride on the machine.

Dirty or slippery steps, ladders, walkways, and platforms can cause falls. Make sure these surfaces remain clean and clear of debris.

Never operate the machine under the influence of alcohol or drugs, or while you are otherwise impaired.

When digging or using ground-engaging attachments, be aware of buried cables. Contact local utilities to determine the locations of services.

Pay attention to overhead power lines and hanging obstacles. High voltage lines may require significant clearance for safety.

Hydraulic oil or diesel fuel leaking under pressure can penetrate the skin, causing serious injury or infection.

• DO NOT use your hand to check for leaks. Use a piece of cardboard or paper.

• Stop the engine, remove the key, and relieve the pressure before you connect or disconnect fluid lines.

• Make sure that all components are in good condition.

Tighten all connections before you start the engine or pressurize the system.

• If hydraulic fluid or diesel fuel penetrates the skin, seek medical attention immediately.

• Continuous long term contact with hydraulic fluid may cause skin cancer. Avoid long term contact and wash the skin promptly with soap and water.

Keep clear of moving parts. Loose clothing, jewelry, watches, long hair, and other loose or hanging items can become entangled in moving parts.

A person or pet within the operating area of a machine can be struck or crushed by the machine or its equipment. DO NOT allow anyone to enter the work area.

Raised equipment and/or loads can fall unexpectedly and crush persons underneath. Never allow anyone to enter the area underneath raised equipment during operation.

Never operate the engine in enclosed spaces as harmful exhaust gases may build up.

Before you start the machine, be sure that all controls are in neutral or park lock position.

Start the engine only from the operator’s seat. If you bypass the safety start switch, the engine can start with the transmission in gear. Do not connect or short across terminals on the starter solenoid. Attach jumper cables as described in the manual. Starting in gear may cause death or serious injury.

Always keep windows, mirrors, all lighting clean to provide the best possible visibility while you operate the machine.

Operate controls only when seated in the operator’s seat, except for those controls expressly intended for use from other locations.

Before you leave the machine: 1. Park the machine on a firm, level surface.

Wear protective equipment when appropriate.

2. Lower the attachment to the ground.

DO NOT attempt to remove material from any part of the machine while it is being operated or while components are in motion.

3. Put all controls in neutral position.

4. Turn off the engine and remove the key.

5. Place the gate lock lever (safety bar) in the upward position.

General maintenance safety Keep the area used for servicing the machine clean and dry. Clean up spilled fluids.

Close all access doors and install all panels after servicing the machine.

Service the machine on a firm, level surface.

Do not attempt to clean, lubricate, clear obstructions, or make adjustments to the machine while it is in motion or while the engine is running.

Install guards and shields after you service the machine.

2-2

2 - SAFETY INFORMATION

Always make sure that working area is clear of tools, parts, other persons and pets before you start operating the machine.

Unsupported hydraulic cylinders can lose pressure and drop the equipment, causing a crushing hazard. Do not leave equipment in a raised position while parked or during service, unless the equipment is securely supported.

Jack or lift the machine only at jack or lift points indicated in this manual.

Incorrect towing procedures can cause accidents. When you tow a disabled machine follow the procedure in this manual. Use only rigid tow bars.

Stop the engine, remove the key, and relieve pressure before you connect or disconnect fluid lines.

Stop the engine and remove the key before you connect or disconnect electrical connections.

Scalding can result from incorrect removal of coolant caps. Cooling systems operate under pressure. Hot coolant can spray out if you remove a cap while the system is hot. Allow the system to cool before you remove the cap. When you remove the cap, turn it slowly to allow pressure to escape before you completely remove the cap.

Replace damaged or worn tubes, hoses, electrical wiring, etc.

The engine, transmission, exhaust components, and hydraulic lines may become hot during operation. Take care when you service such components. Allow surfaces to cool before you handle or disconnect hot components.

Wear protective equipment when appropriate.

When welding, follow the instructions in the manual. Always disconnect the battery before you weld on the machine. Always wash your hands after you handle battery components.

Fire and explosion prevention Fuel or oil that is leaked or spilled on hot surfaces or electrical components can cause a fire.

Crop materials, trash, debris, bird nests, or flammable material can ignite on hot surfaces.

Inspect the electrical system for loose connections and frayed insulation. Repair or replace loose or damaged parts.

Do not store oily rags or other flammable material on the machine.

Always have a fire extinguisher on or near the machine.

Make sure that the fire extinguisher(s) is maintained and serviced according to the manufacturer’s instructions.

At least once each day and at the end of the day, remove all trash and debris from the machine especially around hot components such as the engine, transmission, exhaust, battery, etc. More frequent cleaning of your machine may be necessary depending on the operating environment and conditions.

At least once each day, remove debris accumulation around moving components such as bearings, pulleys, belts, gears, cleaning fans, etc. More frequent cleaning of your machine may be necessary depending on the operating environment and conditions.

Do not weld or flame cut any items that contain flammable material. Clean items thoroughly with non-flammable solvents before welding or flame-cutting.

Do not expose the machine to flames, burning brush, or explosives.

Promptly investigate any unusual smells or odors that may occur during operation of the machine.

Before performing maintenance for electrical systems or electric welding, always place the key of the battery master switch in “OFF” position or disconnect the negative — terminal of the batteries, in order to cut off the electric circuit.

General battery safety Always wear eye protection when you work with batteries.

Do not weld, grind, or smoke near a battery.

Do not create sparks or have open flame near a battery.

When you use auxiliary batteries or connect jumper cables to start the engine, use the procedure shown in the operator’s manual. Do not short across terminals.

Ventilate the area when you charge a battery or use a battery in an enclosed area.

Disconnect the negative — terminal first and reconnect the negative — terminal last.

When you weld on the machine, disconnect both terminals of the battery.

Follow the manufacturer’s instructions when you store and handle batteries.

Battery post, terminals, and related accessories contain lead and lead compounds. Wash hands after handling.

2-3

2 - SAFETY INFORMATION

Battery acid causes burns. Batteries contain sulfuric acid.

Avoid contact with skin, eyes, or clothing. Antidote (external): Flush with water. Antidote (eyes): flush with water for 15 minutes and seek medical attention immediately.

Antidote (internal) : Drink large quantities of water or milk.

Do not induce vomiting. Seek medical attention immediately.

Keep out of reach of children and other unauthorized persons.

Seat belts Seat belts must be worn at all times.

• Replace belts that have cuts that can make the belt weak.

Seat belt inspection and maintenance: • Keep seat belts in good condition.

• Check that bolts are tight on the seat bracket or mounting.

• Keep sharp edges and items than can cause damage away from the belts.

• If the belt is attached to the seat, make sure that the seat or seat brackets are mounted securely.

• Periodically check belts, buckles, retractors, tethers, slack take-up system, and mounting bolts for damage and wear.

• Keep seat belts clean and dry.

• Clean belts only with soap solution and warm water.

• Do not use bleach or dye on the belts because this can make the belts weak.

• Replace all parts that have damage or wear.

Air-conditioning system The air-conditioning system is under high pressure. Do not disconnect any lines. The release of high pressure can cause serious injury.

The air-conditioning system contains gases that are harmful to the environment when released into the atmosphere. Do not attempt to service or repair the system.

Only trained service technicians can service, repair, or recharge the air-conditioning system.

Personal Protective Equipment (PPE) Wear Personal Protective Equipment (PPE) such as hard hat, eye protection, heavy gloves, hearing protection, protective clothing, etc.

Do Not Operate tag Before you start servicing the machine, attach a ‘Do Not Operate’ warning tag to the machine in an area that will be visible.

Hazardous chemicals If you are exposed to or come in contact with hazardous chemicals you can be seriously injured. The fluids, lubricants, paints, adhesives, coolant, etc. required for the function of your machine can be hazardous. They may be attractive and harmful to domestic animals as well as humans.

Material Safety Data Sheets (MSDS) provide information about the chemical substances within a product, safe handling and storage procedures, first aid measures, and procedures to take in the event of a spill or accidental release. MSDS are available from your dealer.

Before you service your machine check the MSDS for each lubricant, fluid, etc. used in this machine. This information indicates the associated risks and will help you service the machine safely. Follow the information in the

MSDS, and on manufacturer containers, as well as the information in this manual, when you service the machine.

Dispose of all fluids, filters, and containers in an environmentally safe manner according to local laws and regulations. Check with local environmental and recycling centers or your dealer for correct disposal information.

Store fluids and filters in accordance with local laws and regulations. Use only appropriate containers for the storage of chemicals or petrochemical substances.

Keep out of reach or children or other unauthorized persons.

Applied chemicals require additional precautions. Obtain complete information from the manufacturer or distributor of the chemicals before you use them.

2-4

2 - SAFETY INFORMATION

Utility safety When digging or using ground-engaging equipment, be aware of buried cables and other services. Contact your local utilities or authorities, as appropriate, to determine the locations of services.

Make sure that the machine has sufficient clearance to pass in all directions. Pay special attention to overhead power lines and hanging obstacles. High voltage lines may require significant clearance for safety. Contact local authorities or utilities to obtain safe clearance distances from high voltage power lines.

Retract raised or extended components, if necessary.

Remove or lower radio antennas or other accessories.

Should a contact between the machine and an electric

power source occur, the following precautions must be taken: • Stop the machine movement immediately.

• Apply the parking brake, stop the engine, and remove the key.

• Check if you can safely leave the cab or your actual position without contact with electrical wires. If not, stay in your position and call for help. If you can leave your position without touching lines, jump clear of the machine to make sure that you do not make contact with the ground and the machine at the same time.

• Do not permit anyone to touch the machine until power has been shut off to the power lines.

Electrical storm safety Do not operate machine during an electrical storm.

If you are on the ground during an electrical storm, stay away from machinery and equipment. Seek shelter in a permanent, protected structure.

If an electrical storm should strike during operation, remain in the cab. Do not leave the cab or operator’s platform. Do not make contact with the ground or objects outside the machine.

Mounting and dismounting Mount and dismount the machine only at designated locations that have handholds, steps, and/or or ladders.

Face the machine when you mount and dismount the machine.

Do not jump off of the machine.

Maintain a three-point contact with steps, ladders, and handholds.

Make sure that steps, ladders, and platforms remain clean and clear of debris and foreign substances. Injury may result from slippery surfaces.

Never mount or dismount from a moving machine.

Do not use the controls or accessories as handholds when you enter or exit the cab.

Working at heights When the normal use and maintenance of the machine requires you to work at heights:

• Do not stand on surfaces that are not designated as steps or platforms.

• Correctly use installed steps, ladders, and railings.

• Never use ladders, steps, or railings while the machine is moving.

Do not use the machine as a lift, ladder, or platform for working at heights.

Lifting and overhead loads Never use loader buckets, forks, etc. or other lifting, handling, or digging equipment to lift persons.

Do not use raised equipment as a work platform.

Know the full area of movement of the machine and equipment and do not enter or permit anyone to enter the area of movement while the machine is in operation.

Never enter or permit anyone to enter the area underneath raised equipment. Equipment and/or loads can fall unexpectedly and crush persons underneath it.

Do not leave equipment in raised position while parked or during service, unless securely supported. Hydraulic cylinders must be mechanically locked or supported if they are left in a raised position for service or access.

Loader buckets, forks, etc. or other lifting, handling, or digging equipment and its load will change the center of gravity of the machine. This can cause the machine to tip on slopes or uneven ground.

2-5

2 - SAFETY INFORMATION

Load items can fall off the loader bucket or lifting equipment and crush the operator. Care must be taken when lifting a load. Use proper lifting equipment.

Equipment and associated loads can block visibility and cause an accident. Do not operate with insufficient visibility.

Do not lift load higher than necessary. Lower loads to transport. Remember to leave appropriate clearance to the ground and other obstacles.

Before using the machine • Avoid loose fitting clothing, loose or uncovered long hair, jewelry or any other items which could get caught up in machinery.

• When alighting from or getting into the operator's compartment, always face the machine and use the steps and access handles.

• Different types of job will require different types of protective equipment. Items such as hard hats, safety shoes, heavy gloves, reflector type jackets, respirators, ear protection and eye protection may be required. Before starting a job, determine what protective equipment will be necessary. Use this equipment at all times.

• Be sure you know the position and function of each control. Incorrect operation of the controls can cause serious injuries.

• Do not attempt to operate this machine unless you have first read and perfectly understood the safety messages and instructions appearing in this manual.

• Operating the machine requires full attention and care on the part of the operator can avoid accidents. Get to know the machine's possibilities and limitations and the working space required. There are areas of poor visibility in the working range of the machine. Have someone guide you for all areas where visibility is not perfect.

• Grease, oil, mud or (in winter) ice on the steps and access handles can cause accidents. Make sure they are kept clean at all times.

• Every day, inspect the machine to detect any signs of hydraulic fluid leakage. Tighten the connections or replace any defective components as necessary.

• Remove any obstructions which hinder visibility. Keep the windshield, rear view mirror and windows clean at all times.

• Make sure the windshield wiper works correctly.

• Make sure you are perfectly familiar with hand signals in daily use on the worksite so as to be able to obtain help with tight manoeuvres or when carrying out operations where visibility is poor.

• Before undertaking any travel or working operations during hours of darkness, make sure the lighting and signalling equipment is fully operative.

• Before any travel operation, make sure that the doors and hoods are properly latched.

• Check that no tools or other items have been left on the machine (be it on the undercarriage or the upperstructure) or in the operator's compartment.

• The operator must be alone on the machine at all times.

Do not allow anyone to stand on or around the machine.

• To get in or out of the cab, it is imperative that the upperstructure frame is in line with the undercarriage.

• Check all controls and safety devices in a safe, open area before starting work.

• Keep away from dangerous areas such as ditches, overhangs, rocky areas, etc. Make a survey of the work-site and determine the possible dangers before using the machine.

• Before parking the machine, make sure that the ground is stable. Plan the worksite so that the ground is flat, hard and level.

• Before moving the machine to work in a new area, walk around to determine all possible causes of accidents there. Holes, obstacles, debris and other danger risks in the working area can cause serious injury.

• Be ready to meet emergencies. Always carry a first aid kit and if possible, fire extinguisher (not supplied) within easy reach on board. Make sure the fire extinguisher is regularly serviced in conformance with the manufacturer's instructions.

• Check the fastening of the main components: counterweight, turntable bearing and operator's compartment.

In the event of problems, consult your NEW HOLLAND CONSTRUCTION Dealer.

• Make sure you understand the symbols used on the machine safety decals. Keep the decals clean so that they are perfectly legible at all times.

• Work out a means of convenient escape from the machine (emergency exit via the windshield or the rear window glass) in the event of the machine turning over or tipping over or the cab door being jammed.

• Make sure you are perfectly familiar with traffic regulations and special safety equipment requirements before transporting this machine on a public highway.

• When loading trucks, never swing the load over the truck cab.

• Before undertaking any travel on the job site, make sure the itinerary to be followed is completely safe. If bridges are to be crossed, make sure they are perfectly capable of supporting the weight of the machine.

• Always steer round large obstacles such as boulders, big trees, etc.

2-6

2 - SAFETY INFORMATION

Operating the machine • When working on a public highway, use standard traffic signs and take into consideration the working range of the upperstructure and its attachments. Local or national regulations stipulate the number, type and location of reflector strips.

• Avoid running the engine in a confined space. If there is no alternative, proper ventilation must be provided at all times.

• Do not allow anyone else on the machine. The passenger could fall or cause an accident.

• Never operate the working or travel controls unless you are properly seated in the operator’s seat with the seat belt correctly fastened.

• Before starting the engine, check the direction of travel (in forward drive, the reduction gears should be to the rear of the machine).

• Do not work near overhead high-voltage electric lines without checking beforehand that all necessary measures have been taken to respect the minimum distances: Less than 57000 volts: 4 m (13.12 ft).

More than 57000 volts: 5 m (16.4 ft).

• Study the position of any existing pipelines or conduits before starting work. Electrical cables, gas and water pipes and other underground installations can cause serious injury.

• Always make allowance for working conditions (sloping or rough ground), the site and weather conditions when driving the machine.

• Do not allow anyone to stand in the machine working area. Accidental operation of the upperstructure swing control or of an attachment control could cause an accident. Stop all operations until everyone has moved away.

• Before operating the dozer blade (if equipped) make sure that there is no one in the working area of the latter.

• Operate all controls gradually to ensure smooth machine operation.

• Whenever load handling operations are to be carried out, it is imperative to adhere strictly to the instructions given in this manual and local legislation.

• It is forbidden to use the machine to carry out tasks other than those for which it is intended. Never use the equipment for sweeping the ground to level out rubble or push objects (transversal stress on the attachment).

• Stop the engine and remove the ignition key when the machine is not in use, even for short periods of time.

• The working area of the end attachment that is mounted may interfere with the machine. Interference may be caused due to the type of end attachment or installation of parts such as a cab guard. Always maintain a safe margin of distance. (Be careful of tool swing or accidental operations.)

• To access or exit the operator’s compartment, the lefthand control arm must be in the raised position. Never forget this basic requirement.

• Never leave the operator's compartment while the engine is running.

• To get in or out of the cab, it is imperative that the upperstructure frame is in line with the undercarriage.

• Dust, smoke or mist can reduce visibility and cause an accident. Reduce speed or come to a complete halt until visibility has improved.

• Never jump down from the machine. When alighting from the machine or the upperstructure, always face the machine and use the steps and access handles.

• In the event of an operating problem or failure, move the machine to a safe place, lower the attachment to the ground, shut down the engine and remove the ignition key. Locate the problem, report it if necessary and take the necessary steps to warn others not to attempt to operate the machine.

• Before tilting the seat back forward, it is mandatory to raise the armrests to avoid any accidental operation of the control levers.

• Never turn the key of the battery master switch in “OFF” position when engine is running, the electrical systems can be damaged.

• When the engine is stopped, always wait one minute minimum before to place the key of the battery master switch in “OFF” position, otherwise the computer program of the hydraulic will not exit successfully.

Preventing risks caused by vibrations The machine's vibration affects the comfort and in some cases the health and safety of the operator. To reduce vibration risks to a minimum: 1. Make sure that the machine, the equipment and the tool are suitable for the work to be carried out.

2. Make sure that the machine is in good condition and that servicing intervals are complied with.

3. Check the track tension adjustment and the play in equipment linkages.

4. Make sure that the operator's seat and is adjustment controls are in good condition and then adjust the seat to suit the operator's size and weight. The operator’s seat complies with the ISO 7096, 2000 standard, EM 6 class.

During work: 1. Operate all controls gradually to ensure smooth machine operation.

2-7

2 - SAFETY INFORMATION

2. Modify the machine's operation to suit the working conditions.

4. Make sure that the machine's operating radius is in good condition, and free of obstacles and holes.

3. During travel, adjust the machine's speed, reducing it if necessary.

Parking the machine When parking the machine, proceed as follows: 1. Position the machine on flat, level ground, away from soft ground, excavations or poorly shored cavities.

2. Place the upperstructure and the attachment in line with the undercarriage, retract the attachment and dig the bucket into the ground.

3. Lower the dozer blade (if equipped) until it rests on the ground.

4. Stop the engine and remove the ignition key.

5. You must place the function cancellation lever in the central position (safety bar in inward position) before leaving the operator’s compartment.

6. Lock the cab door.

7. Make sure that the hoods and doors are properly latched.

8. Check that no part of the machine is encroaching on the highway. If this cannot be avoided, install the necessary regulation signalling equipment.

Maintenance and adjustments • Do not try to service this machine unless you have first read and perfectly understood the safety messages and instructions featuring in this manual.

• When carrying out service work always wear suitable dress. Avoid loose-fitting clothing.

• Release pressure completely in the hydraulic system before disconnecting the hydraulic piping. Hydraulic oil escaping under pressure can cause serious injury.

• Before doing maintenance work on the machine, shut down the engine and allow it to cool down. Otherwise, you could be burned.

• Before commencing any work on the machine, place a "Do not operate" tag on the right-hand control arm.

• Always wear eye protection when using a tool that might project metal particles. Use a hammer with a soft face, such as copper, for installing pins.

• Badly carried out maintenance or adjustments can cause serious injuries. If you do not understand a servicing or adjustment procedure, consult your NEW HOLLAND CONSTRUCTION Dealer.

• If the attachment is raised or if the machine moves without an operator, serious injury can result. Before carrying out maintenance on this machine, proceed as follows: Park the machine on flat, level ground.

Lower the attachment until it is resting on the ground.

Lower the dozer blade (if equipped) until it rests on the ground.

Stop the engine and remove the ignition key.

Lock the tracks to prevent any machine movement.

• Any unauthorized modifications made to this machine can cause serious injury. Do not undertake any modifications without first consulting your NEW HOLLAND CONSTRUCTION Dealer. Any modifications made must be in conformity with the technical specifications of the machine and any current safety legislation requirements.

• Certain components of the machine are subject to type approval. When replacing such components, it is mandatory to make sure that they conform to regulations. For safety's sake, use genuine NEW HOLLAND CONSTRUCTION parts.

• Pressurized hydraulic fluid or grease which penetrates the skin can cause serious injury. Take the necessary safety precautions (safety clothing and protection for face and hands) to avoid such risks. Also, before using these products, read the manufacturer's instructions concerning their use. If hydraulic fluid penetrates the skin, call a doctor immediately.

• Coolant solution is toxic.

Avoid contact with skin, eyes and clothing.

Antidote: External: rinse thoroughly with water and remove soiled clothes.

Internal: do not induce vomiting. Rinse the mouth out with water. Seek medical advice.

Eyes: rinse thoroughly with water and seek medical advice.

• The pressure in the track tension cylinders is high. Follow the procedure described in this manual carefully for increasing or reducing track tension.

• When carrying out a welding operation on the undercarriage or upperstructure carriage as authorized by the manufacturer and in accordance with his instructions, disconnect the batteries, disconnect the alternator B+ and D+ terminal wires and connect the welding apparatus earth cable to the component on which the welding operation is to be performed. Never connect the welding apparatus to the undercarriage when welding on the upperstructure (or vice-versa). Never connect the welding apparatus earth to a component of the hydraulic system.

• When using compressed air, take the necessary precautions to protect your face.

2-8

2 - SAFETY INFORMATION

• Clean the machine regularly. Accumulations of grease, dirt and debris can cause injuries or damage the machine.

• Periodically inspect the fastening of the main components, as part of the machine maintenance programme: counterweight, turntable bearing and operator's compartment. In the event of problems, consult your NEW HOLLAND CONSTRUCTION Dealer.

• If the accumulator is not functioning correctly, consult your NEW HOLLAND CONSTRUCTION Dealer. Never try to carry out any servicing operation on the accumulator. If this instruction is not followed serious injury can result.

• There is high pressure fuel in the feed pipe when the engine is running and immediately after it has been shut down. Wait for 2 minutes after engine shut down before you do any maintenance or inspections to allow the pressure to drop in the pipe.

• High-voltage is charged to the controller and/or to the injector while the engine is running and immediately after it has been shut down.

Do not touch the controller or the injector.

If it is necessary to touch them for maintenance purposes, consult your NEW HOLLAND CONSTRUCTION Dealer.

• The accumulator is charged with nitrogen under high pressure. Do not weld or allow flames to come near to the accumulator.

Using an Implement other than a bucket • When using a special implement (hydraulic breaker, cutter crusher etc.), refer to the operator's manual provided with the implement.

Implement operation and maintenance • For the implement operation and maintenance, refer to the operator's manual provided with the implement.

Safety area The safety area is the space necessary for the machine to operate at the maximum range of the tool and at full swing 360 ° plus 2 m.

(1) Working area.

(2) Safety area.

SMIL13CEX2517AB

2-9

1

2 - SAFETY INFORMATION

Ecology and the environment Soil, air, and water quality is important for all industries and life in general. When legislation does not yet rule the treatment of some of the substances that advanced technology requires, sound judgment should govern the use and disposal of products of a chemical and petrochemical nature.

Familiarize yourself with the relative legislation applicable to your country, and make sure that you understand this legislation. Where no legislation exists, obtain information from suppliers of oils, filters, batteries, fuels, anti-freeze, cleaning agents, etc., with regard to the effect of these substances on man and nature and how to safely store, use, and dispose of these substances. Your NEW HOLLAND CONSTRUCTION dealer can also provide assistance.

Helpful hints • Avoid the use of cans or other inappropriate pressurized fuel delivery systems to fill tanks. Such delivery systems may cause considerable spillage.

• In general, avoid skin contact with all fuels, oils, acids, solvents, etc. Most of these products contain substances that may be harmful to your health.

mosphere. Your NEW HOLLAND CONSTRUCTION dealer or air-conditioning specialist has a special extractor for this purpose and can recharge the system properly.

• Repair any leaks or defects in the engine cooling system or hydraulic system immediately.

• Do not increase the pressure in a pressurized circuit as this may lead to a component failure.

• Protect hoses during welding. Penetrating weld splatter may burn a hole or weaken hoses, allowing the loss of oils, coolant, etc.

Battery recycling Batteries and electric accumulators contain several substances that can have a harmful effect on the environment if the batteries are not properly recycled after use. Improper disposal of batteries can contaminate the soil, groundwater, and waterways. NEW HOLLAND CONSTRUCTION strongly recommends that you return all used batteries to a NEW HOLLAND CONSTRUCTION dealer, who will dispose of the used batteries or recycle the used batteries properly. In some countries, this is a legal requirement.

• Modern oils contain additives. Do not burn contaminated fuels and or waste oils in ordinary heating systems.

• Avoid spillage when you drain fluids such as used engine coolant mixtures, engine oil, hydraulic fluid, brake fluid, etc. Do not mix drained brake fluids or fuels with lubricants. Store all drained fluids safely until you can dispose of the fluids in a proper way that complies with all local legislation and available resources.

• Do not allow coolant mixtures to get into the soil. Collect and dispose of coolant mixtures properly.

• Do not open the air-conditioning system yourself. It contains gases that should not be released into the at-

2-10

NHIL14GEN0038AA

1

2 - SAFETY INFORMATION

Hand signals When operating the machine, never attempt to carry out tasks calling for fine control or working in areas where visibility is poor or impaired without seeking the assistance of a signalman. Make perfectly sure that you and the signalman understand the signals to be used.

Start the engine

Move away from me Wave hands back and forth (palms outwards).

PDE0002ATBP1

1

Shut down the engine

PDE0002TBP1

4

PDE0004ATBP1

5

Go this far

2

Come to me Wave hands back and forth (palms inwards).

PDE0003ATBP1

PDE0003TBP1

All stop and hold

PDE0004TBP1

3

2-11

6

2 - SAFETY INFORMATION

Lower load or tool

Stop Wave one hand back and forth.

PDE0006TBP1 PDE0005ATBP1

10

7

Slowly raise the load or tool Emergency stop Wave hands back and forth.

PDE0007ATBP1

PDE0005TBP1

8

11

Slowly lower the load or tool

Raise load or tool

PDE0007TBP1

PDE0006ATBP1

9

2-12

12

2 - SAFETY INFORMATION

Turn machine left (swing load left)

Lower tool

To stop movement, stop moving hand and clench fist.

PDE0008ATBP1

PDE0009TBP1

16

PDE0010ATBP1

17

PDE0010TBP1

18

13

Lift boom Turn machine right (swing load right) To stop movement, stop moving hand and clench fist.

PDE0008TBP1

14

Lower boom

Raise tool

PDE0009ATBP1

15

2-13

2 - SAFETY INFORMATION

Retract arm

Fill tool

PDE0011ATBP1

19

Extend arm

PDE0012ATBP1

21

PDE0012TBP1

22

Empty tool

PDE0011TBP1

20

2-14

2 - SAFETY INFORMATION

Safety signs WARNING Avoid injury!

An illegible or missing decal can have far-reaching consequences. Inspect decals daily.

Failure to comply could result in death or serious injury.

W0228A

WARNING Avoid injury!

Make sure decals are perfectly legible. Clean decals regularly. Replace all damaged, missing, painted over, or illegible decals. See your dealer for replacement decals. When replacing parts bearing decals, be sure to put new decals on each new part.

Failure to comply could result in death or serious injury.

W0229A

The following safety decals are placed on your machine as a guide for your safety and for those working with you.

Walk around the machine and note the content and location of these safety decals before operating your machine.

Keep safety decals clean and legible. Clean safety decals with a soft cloth, water, and a gentle detergent. Do not use solvent, gasoline, or other harsh chemicals. Solvents, gasoline, and other harsh chemicals may damage or remove safety decals.

Replace all safety decals that are damaged, missing, painted over, or illegible. If a safety decal is on a part that is replaced, make sure the safety decal is installed on the new part. See your NEW HOLLAND CONSTRUCTION Dealer for replacement safety decals.

Safety decals that display the “Read Operator’s Manual” symbol are intended to direct the operator to the operator’s manual for further information regarding maintenance, adjustments, or procedures for particular areas of the machine. When a safety decal displays this symbol, refer to the appropriate page of the operator’s manual.

OM0000

1

NOTE: This chapter only covers decals relating to safety and machine operation and servicing. For information on all decals on the machine, consult the spare parts catalogue.

2-15

2 - SAFETY INFORMATION

Position of decals When replacing a decal, make sure it is located as shown below.

SMIL16CEX1060HB

2-16

2

2 - SAFETY INFORMATION

SMIL16CEX1051HB

2-17

3

2 - SAFETY INFORMATION

Decal placement diagrams Table of safety precautions Part number: KHP12151

UTOLPI-001

4

Interference with attachments The end attachment used for machine operation (e.g. bucket, hydraulic breaker, clamshell...) may hit the cab and/or the boom depending upon the length of the arm, the size of the bucket or the installation of a quick coupler.

Always check the operating range of the machine with the specific attachment in use. Avoid abrupt operation in order to keep proper clearance between the attachment and the cab or boom or other significant parts of the machine.

Collisions between attachment and cab or boom or other significant parts of the machine can cause serious damages.

2-18

X411GJ-001

5

2 - SAFETY INFORMATION

Danger electric line When working near overhead high-voltage electric lines, there is a high risk of electric shocks.

Always keep minimum distances to the electric lines in order to avoid serious damages to the machine, and to avoid serious injuries to the bystanders.

A6ERKX-001

6

4PICYH-001

7

XS2IDH-001

8

TP6IJX-001

9

Seat belt Always fasten the seat belt before starting machine operation.

Operator’s manual Make sure to read the operator's manual to understand how operate the machine properly and safely.

Maintenance or inspection Always stop the engine and remove the starter key before any maintenance operation or inspection of the machine.

2-19

2 - SAFETY INFORMATION

Parking the machine Before leaving the operator's compartment, always lower the bucket to the ground, place the gate lock lever in locked position, stop the engine and remove the starter key in order to prevent any unintended movement of the machine.

GHN2P4-001

10

7XQ428-002

11

Function of the control levers Part number: KHP17370 Functions of the left-control lever and right control lever.

Part number: KHP21160 (Option)

SMIL16CEX1052AA

12

SMIL16CEX0379AA

13

Part number: KHP27030 (Option)

2-20

2 - SAFETY INFORMATION

Part number: KHP27240 (Option)

SMIL16CEX0380AA

14

SMIL16CEX0381AA

15

Part number: KHP27250 (Option)

Windshield locking Part number: KHP12540 Always lock the windshield when it is set in open position.

Windshield not locked may fall down and can affect safe and proper operation of the machine, and can even cause injuries.

QA96IC-001

16

Function of the levers and pedals Part number: KHP27010 (with right-hand option) Functions of travel control levers and pedals.

SMIL16CEX0382AA

2-21

17

2 - SAFETY INFORMATION

Cigarette lighter socket ( 24 V) Part number: KHP11590 24 V electric socket.

Connect only 24 V devices to this socket.

Connecting devices functioning at different voltage can cause damages to the device itself and to the electrical system of the machine.

DEXSB6-001

18

Y6JWU1-001

19

Emergency exit Part number: KHP1247 In case of emergency, use the emergency hammer to break the rear window and get out from the machine.

Power Socket Part number: KHP1803 12 V electric socket.

Connect only 12 V devices to this socket. Connecting devices functioning at different voltage can cause damages to the device itself and to the electrical system of the machine.

477E6EB3

20

Handling precautions in operation compartment Part number: KHP18640 Welding or modification to the cab structure is strictly forbidden.

Welding or modification to the cab structure affects cab's strength, and compromises operator's protection.

SMIL14CEX1623AB

2-22

21

2 - SAFETY INFORMATION

Load Decal Always make sure to lift loads not exceeding the maximum values prescribed by the load lifting table.

SMIL16CEX1053AB

22

Starting the engine Part number: KHP1336 Do not try to start the engine by auxiliary tools. Machine may start to move suddenly and unintendedly causing serious injuries to the operator and to the bystanders.

A4430E4D

23

Risk of falling Part number: KHP12220 Keep away from the edge of the counterweight in order to avoid the risk of falling.

SMIL15CEX0825AB

24

SMIL15CEX0814AB

25

Exhaust Part number: KHP1338 Do not touch the muffler right after engine stop. Muffler surface is hot and touching it can cause serious injuries.

2-23

2 - SAFETY INFORMATION

Exhaust Part number: KHP17410 Do not touch the muffler right after engine stop. Muffler surface is hot and touching it can cause serious injuries.

6A43DED1

26

Radiator Part number: KHP1326 Do not loosen or open the radiator cap when coolant is hot and under pressure, it can cause serious injuries.

Cool down the engine before opening the radiator cap, then loosen the radiator cap slowly to relieve pressure in the coolant circuit.

SMIL15CEX0826AB

27

SMIL15CEX0827AB

28

SMIL15CEX0828AB

29

Fan belt Part number: KHP1337 When the engine is running, keep away from the engine cooling fan, from the fan belt and from the other rotating parts of the mechanical fan drive system.

The engine cooling fan and other rotating parts can cause serious injuries.

Always stop and cool down the engine before making any maintenance operation in the engine compartment.

Check valve Part number: KHP17390 Track tensioning cylinder contains pressurized fluid.

During maintenance of the track tensioning cylinder, fluid may spray out from the check valve on the tensioning cylinder and can cause serious injuries.

Always make sure to read operator's manual to understand proper practices and precautions to be tackled for maintenance of the track tensioning system.

2-24

2 - SAFETY INFORMATION

Batteries Part number: KHP17430 Prevent battery explosion by keeping sparks, open flames and cigarettes away from the batteries. Always make sure to read operator's manual to understand proper practices and precautions to be tackled for maintenance of batteries.

SMIL15CEX0829AB

30

SMIL15CEX0839AB

31

SMIL16CEX1054BB

32

Fuel filter replacement Part number: KHP15770 Always perform the fuel filter replacement after reading the operator's manual.

Servicing table Part number: KRP21870 Reference chart indicating proper timing for machine maintenance. Make sure to read operator's manual to understand proper procedures for servicing the machine.

2-25

2 - SAFETY INFORMATION

Common rail high pressure decal Part number: KHP13160 Common rail injection system contains fuel under extreme pressure that can cause fatal injuries. Do not open the common rail pump, or loosen the common rail high pressure lines, or touch any other component of the common rail injection system. Consult the NEW HOLLAND CONSTRUCTION dealer for service.

SMIL15CEX0840AB

33

SMIL15CEX0835AB

34

Engine operation Part number: KHP17440 Always stop and cool down the engine before making any maintenance operation in the engine compartment.

Do not step on the engine as this can cause serious damages to the engine components and serious injuries to the operator.

Make sure to read operator's manual to understand proper procedures for the engine maintenance.

Tie down point Part number: KHP15201 Point on machine structure for securing the machine during transport.

2C7703EB

35

0748FE51

36

It is forbidden to stand within the working range of the upperstructure Part number: KHP17510 Always make sure to keep the working range of the machine upper structure clear from obstacles and from bystanders.

Always sound the horn before start operating the machine.

The machine upper structure may hit or crush the bystanders causing serious injuries.

2-26

2 - SAFETY INFORMATION

Fuel tank Part number: KHP11700 Use only Low Sulfur diesel fuel.

Usage of different kinds of fuel will cause serious damages to the machine.

Do not perform welding and avoid any operation generating sparks close to the fuel tank.

Fuel is flammable and flames can cause serious injuries.

Make sure to read operator's manual to understand proper procedures to be used for storage

SMIL16CEX0413AA

37

Slinging points Part number: KHP19380 Machine area where the lifting devices shall be routed.

E4393270

38

Hydraulic reservoir Part number: KHP1330 Hydraulic tank contains pressurized hot fluid that can cause serious injuries.

Always shut down the engine, cool down the machine and release pressure in the hydraulic tank before doing any maintenance operation to the hydraulic tank or to the hydraulic system.

SMIL15CEX0836AB

Keep out of work range of attachment Part number: KHP1388 Always make sure to keep the working range of the machine front equipment clear from obstacles and from bystanders.

Always sound the horn before start operating the machine.

The machine front equipment may hit or crush the bystanders causing serious injuries.

CB0B8A4B

2-27

40

39

2 - SAFETY INFORMATION

Danger electric line Part number: KHP18060 When working near overhead high-voltage electric lines, there is a high risk of electric shocks.

Always keep minimum distances to the electric lines in order to avoid serious damages to the machine, and to avoid serious injuries to the bystanders.

SMIL15CEX0842AB

41

SMIL15CEXZ365AB

42

Fuel Line Valve Part number: KHP29620 Thoroughly read and understand the operator's manual before starting inspection and service of the fuel system.

Cautions for Handling Battery Disconnect Switch Part number: KHP22050 Make sure to read operator's manual to understand proper procedures for usage of the battery disconnect switch.

69991EE8

43

FFB3DE4D

44

Camera electrical harness disconnection Part number: KHP18460 (option) Always disconnect the wiring of the cameras before removal of the counterweight.

Make sure to read operator's manual to understand proper procedures to be used for removal of the counterweight.

2-28

2 - SAFETY INFORMATION

Engine hood Part number: KHP12230 Do not step over the engine hood in order to avoid the risk of falling.

SMIL15CEX0824AB

45

SMIL15CEXZ366AB

46

Fan Part number: KHP1335 When the engine is running, keep away from the engine cooling fan, from the fan belt and from the other rotating parts of the mechanical fan drive system.

The engine cooling fan and other rotating parts can cause serious injuries.

Always stop and cool down the engine before making any maintenance operation in the engine compartment.

2-29

2 - SAFETY INFORMATION

2-30

3 - CONTROLS AND INSTRUMENTS

3 - CONTROLS AND INSTRUMENTS###_3_### Access to operator's platform

Frame - Access/Exit Cab door CAUTION Pinch hazard!

Be careful not to get your hand, clothes, etc. caught in the door when closing it.

Failure to comply could result in minor or moderate injury.

C0046A

To open the door, use the handle (1) from the outside and use the handle (2) from the inside.

YARHC2-001

1

YARHC2-002

2

YARHC2-003

3

The door can be latched in completely open position. To unlatch the door, tilt the lever (3) downward.

NOTICE: Do not leave the door ajar. Fix it in a latched position.

NOTICE: When seated in the operator’s compartment, with the engine running, make sure that you do not operate the left-hand control lever inadvertently when unlocking the door. To prevent any incident, place the function cancellation lever in the center position. (Refer to page 3-40).

3-1

3 - CONTROLS AND INSTRUMENTS

Steps and access handles WARNING Fall hazard!

In order to enter or exit the cab, the upper structure frame must be in line with the undercarriage.

Failure to comply could result in death or serious injury.

W0225A

WARNING Fall hazard!

Clean the steps and access handles to remove all traces of grease, oil, mud, and ice (in winter).

Failure to comply could result in death or serious injury.

W0139A

WARNING Fall hazard!

Jumping on or off the machine could cause an injury. Always face the machine, use the handrails and steps, and get on or off slowly. Maintain a three-point contact to avoid falling: both hands on the handrails and one foot on the step, or one hand on the handrail and both feet on the steps.

Failure to comply could result in death or serious injury.

W0141A

To get in or out of the machine use the steps (2), the tracks and the access handles (1).

NOTICE: When alighting from or getting into the operator’s compartment, never use the left-hand control arm or the control levers for assistance.

3-2

RLFF4A-001

4

RLFF4A-002

5

3 - CONTROLS AND INSTRUMENTS

Position of the operator’s compartment controls and accessories WARNING Misuse hazard!

Before starting the engine, make sure you are fully aware of the location and the function of each control.

Failure to comply could result in death or serious injury.

W0226A

SMIL16CEX0349GB

3-3

1

3 - CONTROLS AND INSTRUMENTS

1.

Operator's seat

2.

Left-hand control arm

3.

Emergency shutdown switch

4.

Air conditioning control switch

5.

Function cancellation lever and lifting the control arm

6.

Left-hand control arm tilt adjustment lever

7.

Safety bar

8.

Left-hand control lever, arm and upperstructure swing controls

9.

Footrest or option pedal

10. Travel control levers and pedals 11. Footrest or option pedal 12. Front right-hand console monitor display 13. Right-hand control arm 14. Right-hand control lever, boom and bucket controls 15. Right-hand control arm tilt adjustment lever 16. Right-hand switch panel 17. Air vents 18. Storage compartment 19. Fuse box

3-4

3 - CONTROLS AND INSTRUMENTS

Operator's seat

Mechanical suspension seat In order to operate the machine correctly and with maximum efficiency and comfort, adjust the seat to suit the weight and size of the operator.

NOTE: The adjustment of the seat can only be carried out when the operator is seated in the seat, the engine is shut down and the ignition key is set to "ACC" (accessory current supply).

SMIL16CEX0350FB

1

1. Height adjustment

5. Headrest adjustment

2. Longitudinal position adjustment section

6. Seat back angle adjustment section

3. Armrest angle adjustment

7. Lumbar support adjustment

4. Seat and control arm assembly fore and aft adjustment

3-5

3 - CONTROLS AND INSTRUMENTS

A. Seat up-down adjustment Without resting the weight of your body on the seat, adjust the seat height by turning the seat height knob (1).

• To raise: turn to the right (clockwise).

• To lower: turn to the left (counter-clockwise).

SMIL16CEX0287AB

2

SMIL16CEX0288AB

3

SMIL16CEX0289AB

4

SMIL16CEX0290AB

5

B. Seat forward-back adjustment • Pull up the slide lever (2) to adjust the seat position forward and back.

• When you have found the correct forward-back position, release the lever (2) to fasten the seat in place.

C. Reclining adjustment • Pull the reclining adjustment lever (6) to adjust the backrest angle.

• When you have found the correct angle, release the lever (6) to fasten the backrest in place.

D. Armrest • Turning the adjustment dial (3) at the bottom of the armrests allows you to adjust the angle of the armrests.

• The armrests can spring up to the side of the backrest.

3-6

3 - CONTROLS AND INSTRUMENTS

E. Suspension adjustment • Turn the seat height knob (1) clockwise to adjust the seat firmness.

SMIL16CEX0287AB

6

SMIL16CEX0291AB

7

SMIL16CEX0292AB

8

F. Console and seat slide adjustment • Pull the slide lever (4) to adjust the overall position.

• When you have found the correct forward-back position, release the lever (4) to fasten in place.

G. Seat pocket The rear side of the backrest has a pocket. Use this pocket to store the operator's manual etc.

H. Seat belt WARNING Equipment failure could cause accident or injury!

Always fasten the seat belt securely before you operate the machine. Inspect seat belt parts for wear and damage. Replace any and all worn or damaged parts of the seat belt prior to operation.

Failure to comply could result in death or serious injury.

W0046C

NOTICE: If the seat belt has been used for a long time and there is visible damage or unraveling or the fittings are deformed or damaged, replace the seat belt. Even if there is nothing visibly abnormal, replace the seat belt every 3 years.

Always fasten the seat belt before starting to operate the machine.

Check that the seat belt is not twisted, then insert into the buckle.

Make sure that the seat belt is securely locked.

3-7

3 - CONTROLS AND INSTRUMENTS

I. Headrest adjustment The headrest (5) can be adjusted up and down.

• To adjust the headrest up and down, hold it with both hands, and move it lightly upward or downward.

• When being adjusted downward, it will stop at the lock.

To lower it more, press the lock button to unlock it.

SMIL16CEX0293AB

9

J. Lumbar support adjuster This is equipped on the left side of the seat back.

• Turn the dial (7) to adjust the bulge of the lumber area in the lumbar region.

SMIL16CEX0294AB

3-8

10

3 - CONTROLS AND INSTRUMENTS

Air suspension seat (option) In order to operate the machine correctly and with maximum efficiency and comfort, adjust the seat to suit the weight and size of the operator.

NOTE: The adjustment of the seat can only be carried out when the operator is seated in the seat, the engine is shut down and the ignition key is set to "ACC" (accessory current supply).

SMIL16CEX0285FB

1.

2.

3.

4.

Height and weight adjustments Longitudinal position adjustment section Arm rest angle adjustment section Longitudinal adjustment section of the seat/control arm ASSY

5.

6.

7.

8.

1

Head rest adjustment section Seat back angle adjustment section Lumbar support adjustment section Weight adjustment indicator

3-9

3 - CONTROLS AND INSTRUMENTS

A. Height and weight adjustment section • Move the handle (1) up and down to adjust the seat height.

• Lifting the handle (1) fills the air to raise the seat.

• Lowering the handle (1) releases the air to descend the seat.

• After the adjustment, be sure to sit in the seat and check that the indicator (8) color is in green. When the indicator (8) color is in red, the operator's weight is beyond the proper weight range. Readjust the seat height, so the indicator (8) color turns to green, which indicates that the operator's weight is within the proper range.

SMIL16CEX0326AB

2

SMIL16CEX0327AB

3

SMIL16CEX0328AB

4

SMIL16CEX0329AB

5

B. Longitudinal position adjustment section • Move the seat longitudinally while the slide lever (2) is at the lifted position.

• Release the slide lever (2) when the lever is at an appropriate position.

C. Seat back angle adjustment section • Lift the lever (6) to adjust the seat back angle.

• Move the seat back to the desired position and release the lever (6).

D. Armrest angle adjustment • Raise the armrest and adjust to the desired angle using the knob (3), then lower the armrest.

3-10

3 - CONTROLS AND INSTRUMENTS

Longitudinal adjustment section of seat/control arm assy • Lift the slide lever (4) and move the seat/control arm assy longitudinally • Release the slide lever (4) when the lever is at an appropriate position.

SMIL16CEX0330AB

6

SMIL16CEX0292AB

7

F. Seat pocket The rear side of the backrest has a pocket. Use this pocket to store the operator's manual etc

G. Seat belt WARNING Equipment failure could cause accident or injury!

Always fasten seat belt securely before operating the machine. Inspect seat belt parts for wear and/or damage. To ensure operator safety, replace any and all damaged parts of the seat belt prior to operation.

Failure to comply could result in death or serious injury.

W0046A

NOTICE: If the seat belt has been used for a long time and there is visible damage or unraveling or the fittings are deformed or damaged, replace the seat belt. Even if there is nothing visibly abnormal, replace the seat belt every 3 years.

Always fasten the seat belt before starting to operate the machine Check that the seat belt is not twisted, then insert into the buckle.

Make sure that the seat belt is securely locked.

3-11

3 - CONTROLS AND INSTRUMENTS

H. Headrest adjustment section • The headrest (5) can be adjusted up and down.

SMIL16CEX0293AB

8

SMIL16CEX0294AB

9

I. Lumbar support adjuster This is equipped on the left side of the seat back.

• Turn the dial (7) to adjust the bulge of the lumber area in five levels.

3-12

3 - CONTROLS AND INSTRUMENTS

Forward controls

Hand control levers and pedals Left-hand control lever The speed of movement of the arm or the upperstructure swing depends on the control lever tilt angle. In the intermediate position two movements can be obtained simultaneously.

NOTE: When the upperstructure swing control is released, the upperstructure may continue to rotate due to the force of inertia. In this event, make allowance for the extra movement by releasing the control slightly earlier.

B718A878

1

(1) The arm extends.

(2) The arm retracts.

(3) The upperstructure turns to the left.

(4) The upperstructure turns to the right.

VF3UDD-002

3-13

2

3 - CONTROLS AND INSTRUMENTS

Right-hand control lever The speed of movement of the boom or the bucket depends on the control lever tilt angle. In the intermediate position two movements can be obtained simultaneously.

3E160767

(5) (6) (7) (8)

3

The boom lowers.

The boom raises.

The bucket retracts (filling).

The bucket extends (dumping).

FIQCKA-002

4

Travel control levers and pedals The travel control levers and pedals are used to move the machine. (Refer to page 4-14).

NOTE: Travel speed either forward or in reverse depends on the position of the travel speed selector. (Refer to page 4-24 ).

KW9JGV-001C

3-14

5

3 - CONTROLS AND INSTRUMENTS

Auxiliary pedal (if equipped) WARNING Unexpected machine movement!

ALWAYS lock the auxiliary pedals when not in use.

Failure to comply could result in death or serious injury.

W0222A

The auxiliary pedal allows to control the auxiliary high-flow hydraulic circuit. This circuit is intended to operate highflow hydraulic attachments. (Refer to page 4-24 ).

See chapter “Adjustment and locking auxiliary pedals”.

7SALJI-001

6

NOTICE: Consult your NEW HOLLAND CONSTRUCTION Dealer before mounting optional tools.

Footrest

GTQCYL-001B

3-15

7

3 - CONTROLS AND INSTRUMENTS

Adjustment and locking the auxiliary pedals (if equipped) WARNING Unexpected machine movement!

Shut down the engine before adjusting the auxiliary pedals.

Failure to comply could result in death or serious injury.

W0277A

The auxiliary pedal shall be set according to the operating condition.

If any hydraulic attachment is used, the pedal must be locked by engaging the locking pin (1) in the locking hole (2).

SNKQ6K-003

8

If a single-acting hydraulic attachment is used, the pedal must be partially unlocked by engaging the locking pin (1) in the sliding hole (3).

SNKQ6K-002A

9

If a double-acting hydraulic attachment is used, the pedal must be fully unlocked by putting the pin (1) ahead of the pedal.

SNKQ6K-001

3-16

10

3 - CONTROLS AND INSTRUMENTS

Windshield CAUTION Pinch hazard!

Make sure you correctly follow the instructions in this manual when handling the windshield. If you do not handle the windshield correctly, it could slip and injure your fingers or hands.

Failure to comply could result in minor or moderate injury.

C0045A

Opening NOTICE: Lock the gate with the function cancellation lever.

1. Fold the sunshield (1) back against the windshield and operate the lever (2). Hold the lower and upper handles (3) and carefully raise the windshield.

DU3Y32-001

1

DU3Y32-002

2

GSVC6J-001

3

2. Pull the windshield to the rear until it engages perfectly behind the cab.

Closing 1. Use the lever (2) to release the windshield.

2. Hold both handles (3) and carefully lower the windshield. Make sure the window is completely down.

3. Make sure the top of the windshield is correctly latched.

3-17

3 - CONTROLS AND INSTRUMENTS

Front lower window The front lower window may only be removed when the windshield is open.

1. Remove the window from its housing by sliding it upward.

T3FQE4-001A

1

T3FQE4-002A

2

2. Place the window in the storage position provided to the left of the operator's seat and then engage it correctly.

3-18

3 - CONTROLS AND INSTRUMENTS

Front right-hand console 1. Temperature probe Do not place objects on top of it.

2. Monitor display Clock, Fuel Meter, Coolant Water Thermo meter, Hydraulic Oil Thermo meter.

Displays the function selection status.

Displays the machine status.

Displays the back monitor.

Displays the machine maintenance status.

3. Monitor switch Selects the machine status. The monitor display can be switched.

4. Air vents The air vents control the circulation and direction of air flow. The air vents are opened and controlled manually.

NOTICE: the air vents must always be open when the air conditioning is in use.

SMIL16CEX0689BB

3-19

1

3 - CONTROLS AND INSTRUMENTS

System display and function control panel

SMIL16CEX0600FB

1

SMIL16CEX0601FB

2

3-20

3 - CONTROLS AND INSTRUMENTS

1.

2.

3.

Engine coolant temperature gauge Displays the temperature of the engine coolant.

The lower zone indicates that the engine coolant temperature is low.

When the temperature gauge display reaches the upper zone, an alarm sounds and "Over heat" is displayed (see "Message screens").

Lower the engine speed.

If the temperature does not go down, stop the engine, remove the ignition key, and investigate the cause.

Hydraulic oil temperature gauge Displays the temperature of the hydraulic oil.

The lower zone indicates that the hydraulic oil temperature is low.

When the temperature gauge display reaches the upper zone, an alarm sounds and "Over heat" is displayed (see "Message screens").

Lower the engine speed.

If the temperature does not go down, stop the engine, remove the ignition key, and investigate the cause.

Displayed when auto idling and auto stop are selected. “Auto n/min” and “Auto idle stop”.

8.

Work mode icon

Anti-theft protection Displayed when the anti-theft protection function is operating.

9.

Displays the selected attachment

Hydraulic breaker

Fuel gauge Displays the remaining amount of fuel by the number of lit segments.

When all are lit, it indicates that the fuel tank is full.

When only 1 is lit, an alarm sounds and "Low fuel" is displayed (see "Message screens").

NOTE: It is not necessary to wait until the fuel tank is empty before filling with fuel. If the tank becomes empty, air bleeding of the fuel system is required.

4.

Displayed when auto stop is selected.

“Auto idle stop”.

Crusher grapple 10. Clock display (Refer to page 3-37 ).

11. Auxiliary setting display When an auxiliary hydraulic circuit is mounted, the selected flow and pressure are displayed.

These indicators display the initial work mode and the engine speed that was selected with the engine acceleration button and work mode selector..

5.

Travel mode icon At low speed, is displayed.

At high speed, is displayed.

MUC8LU-043Z

6.

Working light Displayed when the light is on.

7.

3

Icon display The setting that the wiper, idling and glow switches are switched to are displayed largely in the middle of display.

• Wiper operation Displayed when the wiper operation is switched.

1st speed

Engine auto idling and stop selection display Displayed when auto idling is selected.

“Auto n/min”.

3-21

3 - CONTROLS AND INSTRUMENTS

2nd speed

Displayed when the radio volume is muted.

Stop

15. Hour meter The hour meter displays the engine operation time in units of 0.1 hr. (6 min.).

• Idle mode Displayed when the engine auto idling and idle stop operations are switched.

Auto idling

16. Fuel economy display and DTC (Diagnostic Trouble Code) display The instantaneous time/fuel consumption “gph” is displayed.

The DTC (Diagnostic Trouble Code) is displayed here.

17. Message screens

Auto idle stop

Auto idling and idle stop

• Pre-heating (glowing)

MUC8LU-042Z

12. Eco gauge The number of indicators on this gauge increases when the operating state is energy-saving operation.

If high-load operations are performed, the number of gauge indicators decreases.

The state of energy-saving operations is indicated.

• No mechanical abnormalities will occur even if the number of gauge indicators decreases. However, to help conserve the environment, try to perform energy-saving operations within the green range, so long as doing so does not hinder work.

Key points for energy-saving operations • Try to use H mode or A mode instead of SP mode.

• Avoid sharp lever operations.

• Avoid high load and relief operations.

• Use auto idle and one-touch idle.

Also, use idle stop to stop unnecessary idling.

Ask your NEW HOLLAND CONSTRUCTION Dealer about how to turn the eco gauge display “On” and “Off”.

4

This section of the display screen shows information icons and messages that change according to the set application of the machine.

An alarm also sounds when some of these messages are displayed.

The following section describes the icons, messages, and their corresponding explanations.

NOTICE: If a message is displayed, perform maintenance according to the message. If the message is still displayed after maintenance, consult your NEW HOLLAND CONSTRUCTION Dealer NOTE: The language of the displayed messages can be changed, consult your NEW HOLLAND CONSTRUCTION Dealer.

• Low oil pressure Indicates that the engine oil level is low. An alarm sounds. Stop the engine and remove the ignition key, and then inspect the oil level.

13. Auto pressure boost icon

NOTE: If the measures above are not performed immediately when this message is displayed, the engine stops automatically.

Displayed when the maximum output state is entered automatically for the attachment.

• Over heat 14. Mute icon

3-22

3 - CONTROLS AND INSTRUMENTS

• Check camera

Indicates that the engine coolant or the hydraulic oil temperature is high. An alarm sounds. Lower the engine speed. If the temperature does not go down, stop the engine and remove the ignition key. Wait for the temperature of the cooling system to go down, and then inspect the coolant level inside the reservoir tank and radiator.

Check the radiator and oil cooler. (Refer to page 6-56).

Indicates that there is a problem (short or disconnection) in the monitor camera connection.

• Over load The load is excessive. Reduce the load.

• Boost temp high

• Low coolant

Indicates that the temperature of the turbocharger air that is being supplied to the engine is abnormally high. An alarm sounds.

The engine automatically enters idling mode as a preventative measure. Stop the machine, operate the engine at idling speed, and wait until the message disappears. If the turbocharger air temperature on the display screen continues to rise, the engine stops automatically. Consult your NEW HOLLAND CONSTRUCTION Dealer.

Indicates that there is insufficient coolant.

An alarm sounds. Stop the engine and remove the ignition key. Wait for the temperature of the cooling system to go down, and then inspect the coolant level inside the reservoir tank and radiator. (Refer to page 6-56).

• Air filter Perform maintenance of the air cleaner filter.

• Alternator Indicates that there is a problem in the alternator. An alarm sounds. Stop the engine and remove the ignition key, and then inspect the alternator. Consult your NEW HOLLAND CONSTRUCTION Dealer.

• Low fuel The fuel in the fuel tank is low. Fill the tank with fuel.

• Check engine Indicates that there is a problem (short or disconnection) in the electrical system of the engine. An alarm sounds. Stop the engine and remove the ignition key, and then inspect the electrical system. Consult your NEW HOLLAND CONSTRUCTION Dealer.

• Hydraulic oil filter The hydraulic oil filter must be replaced.

• Check flow rate Check whether the flow is suitable for the attachment.

• Electrical problem Indicates that there is a problem in the electrical system. An alarm sounds. In this case, stop the engine and remove the ignition key, and then investigate the cause or consult your NEW HOLLAND CONSTRUCTION Dealer.

• Auxiliary set-up required Displayed when an option line operation is performed but the option line mode is not selected correctly.

• Engine stop Indicates that the emergency stop switch operated. An alarm sounds. To enable the engine to be started again, the switch must be canceled.

• Improper shut down

• Service due Displayed when service is due for an oil filter. For details on the maintenance, see "Maintenance information" in the menu.

• Engine idling

Let the engine run at low idle speed for at least 5 min. before stopping the engine.

3-23

3 - CONTROLS AND INSTRUMENTS

Indicates that the engine is idling because engine idling is selected.

• Idle shut down Displayed before the engine is stopped with engine auto stop.

• Auto warm up Indicates that auto warm up is operating.

3-24

3 - CONTROLS AND INSTRUMENTS

Monitor switches

1

13F02278

1. Travel mode select switch The selection toggles between slow speed mode (“Turtle”) and fast speed mode (“Rabbit ”) every time the travel mode selector switch is pressed.

When the switch is pressed again to operate the wipers continuously, (II) is displayed on the monitor.

When the switch is pressed again to stop the wipers, “Off” is displayed on the monitor.

NOTICE: perform all changes to the travel mode while the machine is stopped.

NOTICE: Do not operate the wipers when the front glass is dry. Doing so could damage the wipers.

Use the "Turtle" mode to travel on slope, off-road or soft ground.

Use the “Rabbit” mode to travel on a hard, flat, maintained road.

5. Windshield washer switch The windshield washer and wipers operate while this switch is pressed, and they stop when the switch is released.

NOTE: the slow speed mode is automatically selected when the engine is started.

NOTICE: Do not operate the washer when the reservoir is empty. Doing so could damage the electric pump.

NOTE: if the fast speed mode is selected on the machine, it automatically switches to slow speed mode when the load increases on uphill road, and automatically returns to fast speed mode as the load decreases.

2. Fuel consumption indicator switch Push to show alternately on the display the cumulative average fuel consumption or the cumulative fuel consumption amount.

- Cumulative average fuel consumption: displayed in L/hr.

- Cumulative fuel consumption: displayed in L. Push the fuel consumption indicator switch for 3 seconds to reset the cumulative average fuel consumption and cumulative fuel consumption amount.

3. Attachment select switch When using an optional attachment such as a breaker or crusher, press this switch to switch to a suitable flow and pressure.

Switching to the registered patterns occurs if the switch is pressed.

The selected attachment is displayed on the monitor screen.

NOTICE: before changing the attachment type, stop operation and set the machine in parking position.

4. Front wiper switch This switch has 3 positions: “Off”, "Intermittent" and "Continuous".

When the switch is pressed to operate the wipers intermittently, (I) is displayed on the monitor.

6. Working light switch Use this switch to turn the working light on or off.

When the switch is pressed, the indicator and the working light turn on. Press again to turn them off.

7. Engine auto idling and auto stop switch Press this switch to switch between normal idling (switch on the right side control lever), auto idling, and auto stop.

When this switch is pressed, an indicator is displayed on the monitor.

• In auto idling, “Auto n/min” is displayed, and in normal idling, the display turns off.

If 5 sec. elapse without any operations while this position is selected, the engine transitions to the idling speed. (This interval can be lengthened. Consult your NEW HOLLAND CONSTRUCTION Dealer.)

When a part such as the control lever or pedal is operated, the engine returns to its original speed.

• In auto stop, "Auto stop" is displayed.

- Engine speed is 1200 rpm or less.

"Idling" state - If 3 min. elapse with the function cancellation lever closed and without changing the engine speed, "Idle shut down" is displayed on the monitor.

- About 10 sec. after "Idle shut down" is displayed, the engine stops.

3-25

NOTICE: To protect the engine, at least 3 min. of idling is required.

3 - CONTROLS AND INSTRUMENTS

• Mode 2: Camera screen

NOTE: To restart the engine, first set the ignition key to “Off”, and then start the engine.

• In auto idling and auto stop, “Auto n/min” and "Auto stop" are displayed.

NOTE: If they are still selected when the engine is stopped, they will remain active when the engine is restarted.

8.

Menu screen display switch Press this switch to display the menu screen.

The menu contains the following items.

Language Brightness (day) Brightness (night) Fuel consumption indicator Maintenance information Clock adjust Auxiliary hydraulics Camera setting Use the switch shown in the diagram to select or a change a menu item.

SMIL16CEX0598AA

4

Machine information plus camera joint display • Mode 3: Camera screen without indicators

SMIL16CEX0599AA

5

Camera image independent display (mode, travel mode, clock and warning only) The 3 types above are available for selection.

MUC8LU-026

2

Refer to page 3-27 for use.

9.

Camera display switch Press this button to switch between the machine information screen, machine information + camera joint display, and camera image independent display (mode, travel mode, clock and warning only).

• Mode 1: Normal screen

10. Hour meter select/back monitor select switch In the information screen, hour meter select is enabled.

"Trip" control (partial hour meter) Used to calculate a specific operation time.

Press the control to set the hour meter display to 0 and display the "Trip" message.

Release the control.

After about 1 min., the "Trip" display disappears and the normal hour meter display returns.

To view the specific operation time, press the control and release it immediately.

To cancel the specific operation time, press and hold the control for about 2 sec.

The specific time display returns to 0.

NOTE: If the key is switched “Off”, the hour meter goes out. If the hour meter button is pressed after the key is switched “Off”, only the hour meter will be displayed for 20 seconds.

SMIL16CEX0597AA

NOTE: When a camera image is displayed, the camera image is switched each time the camera select switch is pressed.

3

Machine information screen

3-26

3 - CONTROLS AND INSTRUMENTS

Menu screen display Menu display Push button (1).

1

SMIL16CEX0594AA

Language 1. Push button (1) or (2).

2. Select item "English" or another language.

3. Push button (3) to access the following menu.

If (4) is pressed, the display returns to the machine information screen (original screen).

K38QEJ-002

2

UJ5ZBX-002

3

Brightness (day) 1. Push button (1) or (2).

2. Pushing button (1) is down level. Pushing button (2) is up level.

3. Push button (3) to access the following menu.

If (4) is pressed, the display returns to the machine information screen (original screen).

3-27

3 - CONTROLS AND INSTRUMENTS

Brightness (night) 1. Push button (1) or (2).

2. Pushing button (1) is down level. Pushing button (2) is up level.

3. Push button (3) to access the following menu.

If (4) is pressed, the display returns to the machine information screen (original screen).

J2B7NV-002

4

Y2Q5JH-002

5

Fuel consumption indicator 1. Push button (1) or (2).

2. Select item “On" or “Off”.

3. Push button (3) to access the following menu.

If (4) is pressed, the display returns to the machine information screen (original screen).

Maintenance information 1. Push button (3) or (4).

2. Select item of "Maintenance information".

3. Push button (2).

4. Push button (1) or (2).

5. Select page of 1 or 2 or 3.

Perform maintenance and reset the maintenance time.

1. Push button (3) or (4).

2. Select item.

3. Long-push on button (2) to reset remaining time.

NOTE: When the maintenance time is in the near future, the remaining time displays in yellow. When the maintenance time has passed, the remaining time displays in red.

3-28

NB1Y5Z-004Z

6

3 - CONTROLS AND INSTRUMENTS

If (5) is pressed, the display returns to the menu screen.

If it is pressed one more time, the display returns to the machine information screen.

NB1Y5Z-005Z

7

Auxiliary hydraulics Pattern 1 1. Push menu button (1).

8

SMIL16CEX0594AA

2. Select "Auxiliary hydraulics".

8KYGS8-002

9

3. The auxiliary hydraulics screen is displayed by carrying out operations 1 and 2.

KS1YPB-002

3-29

10

3 - CONTROLS AND INSTRUMENTS

Pattern 2 1. Long-push button (1).

Attachment select switch

11

SMIL16CEX0595AA

2. The auxiliary hydraulics screen is displayed by carrying out operation 1.

KS1YPB-002

12

AXFRYQ-002

13

Breaker or crusher selection 1. Push button (3) or (4) and select item "Attachment type".

2. Push button (1) or (2) and choose attachment type "Breaker" or "Crusher".

3-30

3 - CONTROLS AND INSTRUMENTS

Breaker or crusher No. 1. Push button (3) or (4) and select item of "Breaker No" or "Crusher No".

2. Push button (1) or (2) and choose "Breaker No" or "Crusher No".

3. Push button (1) to move to left.

Push button (2) to move to right.

WQVYH3-002

14

NEMECY-002

15

G6CHU1-002

16

Flow setting 1. Push button (3) or (4) and select item of "Set max flow".

2. Push button (1) or (2) and choose maximum number or flow.

3. Pushing button (1) is down number.

Pushing button (2) is up number.

Pressure setting (if equipped) 1. Push button (3) or (4) and select item of "Set max pressure".

2. Push button (1) or (2) and choose maximum number of pressure.

3. Pushing button (1) is down number.

Pushing button (2) is up number.

3-31

3 - CONTROLS AND INSTRUMENTS

Adjust pressure (if equipped) If change valve of maximum flow or maximum pressure, system has to adjust the proportional relief solenoid valve.

1. Push button (3) or (4).

2. Select item of “Adjust pressure” and push button (4), then pressure adjustment screen is displayed.

LMXLB3-002

17

LMXLB3-009

18

LMXLB3-003

19

LMXLB3-004

20

When adjusting the pressure, depress the option pedal completely, or slide the proportional switch to maximum.

• If low flow and high pressure are selected, the adjustment setting may not input.

• If high flow and low pressure are selected, the adjustment setting may not input.

Adjust pressure setting 1. Raise the oil temperature according to “Bringing the machine up to operating temperature”.

2. Put the throttle volume in “SP” mode.

3-32

3 - CONTROLS AND INSTRUMENTS

3. Press the option pedal for the “Breaker/crusher’s” completely, or slide the proportional switch to maximum.

NOTE: Make adjustments before connecting to an attachment.

LMXLB3-005

21

LMXLB3-006

22

LMXLB3-007

23

LMXLB3-008

24

4. Hold the switch until “Pressure adjusting complete” is displayed on the screen.

5. Operation complete.

6. Returns automatically.

3-33

3 - CONTROLS AND INSTRUMENTS

Camera setting Menu display/camera setting 1. Push button (3) or (4) and select item of "Camera setting".

2. Push button (2).

NOTE: A maximum of 3 cameras can be installed. Consult your NEW HOLLAND CONSTRUCTION Dealer if you would like to install an additional camera.

CS1NXY-001

3-34

25

3 - CONTROLS AND INSTRUMENTS

Camera1 1. Push button (3) or (4).

2. Select item Camera1”.

3. Push button (1) or (2).

4. Select item “On” or "On:mirror view" or “Off”.

Camera2 1. Push button (3) or (4).

2. Select item "Camera2".

3. Push button (1) or (2).

4. Select item “On” or "On:mirror view" or “Off”.

CS1NXY-002

Camera3 1. Push button (3) or (4).

2. Select item "Camera3".

3. Push button (1) or (2).

4. Select item “On” or "On:mirror view" or “Off”.

2–View display (Camera1+2) 1. Push button (3) or (4).

2. Select item "2-View display (Camera1+2)".

3. Push button (1) or (2).

4. Select item “On” or “Off”.

2-View display (CAMERA1+3) 1. Push button (3) or (4).

2. Select item "2-View display (Camera1+3)".

3. Push button (1) or (2).

4. Select item “On” or “Off”.

Full screen display 1. Push button (3) or (4).

2. Select item "Full screen display".

3. Push button (1) or (2).

4. Select item “On” or “Off”.

On screen display (Camera No.) 1. Push button (3) or (4).

2. Select item "On screen display (Camera No.)".

3. Push button (1) or (2).

4. Select item “On (1)" or “On (2)" or “On (3)" or “Off”.

3-35

26

3 - CONTROLS AND INSTRUMENTS

Camera mode switch The screen display switches each time the camera switching button (1) is pressed.

27

SMIL16CEX0596AA

The pictures above display when all camera outputs are set to “On”.

There is a maximum of 5 types of screen displays.

(1): Camera1 (2): Camera2 (3): Camera3

EH85RT-005

3-36

28

3 - CONTROLS AND INSTRUMENTS

Clock adjustment 1. Press the menu button (1) to display the menu screen.

AB6BF4C1

1

2. Select "Clock adjust" in the menu screen by pressing buttons (2) to (3) and enter by pressing button (5).

ETGE0B-004

2

ETGEOB-005

3

3. Set the time on "Hour : Minutes" by pressing buttons (2) to (3) and (4) to (5) and return to the menu screen by pressing (1).

3-37

3 - CONTROLS AND INSTRUMENTS

Left-hand side controls

Left-hand control arm

1

8E3FBA12

1. Arm angle adjustment lever: the lever enables the control arm to be adjusted in different inclines in accordance with the operator's body profile. Hold the lever and select the desired position, and then release the lever.

NOTICE: stop the engine before adjusting the control arm.

2. Gate lock lever.

3. Safety bar.

4. Horn button.

NOTICE: make sure to sound the horn before starting the engine and resuming machine operation.

6. Radio mute button: the radio mute button is located underneath the control lever. Push the button to mute the volume. Push it again to resume the volume.

7. Control of heating, ventilation or air conditioning.

8. Emergency stop switch: the emergency stop switch enables the engine to be shut down in emergency or when it is not possible to shut it down by means of the starter key. Press on the front of the switch to stop the engine. The audible warning device sounds and the "Engine stop" icon is displayed. To start the engine again, press on the back of the emergency stop switch and turn the starter key.

5. Storage tray.

3-38

NOTICE: the emergency stop switch should be used for emergency purpose only.

3 - CONTROLS AND INSTRUMENTS

When the machine is equipped with the auxiliary low-flow hydraulic circuit, the left-hand control lever includes: 1. Proportional switch to operate double-acting hydraulic attachments.

2. ON/OFF button to operate the preferred operating direction of the double-acting hydraulic attachment.

3. Horn button.

SMIL15CEXY839BA

3-39

2

3 - CONTROLS AND INSTRUMENTS

Gate lock lever and safety bar WARNING Unexpected machine movement!

Before you leave the operator's compartment, the gate lock lever must be in the central position and the safety bar must be in the inward position.

Failure to comply could result in death or serious injury.

W1384A

The gate lock lever (2) allows to cancel the functioning of the control levers and pedals and operates the safety bar (1).

103B9E4A

1

The safety bar prevents the operator from leaving the cab without previously operating the gate lock lever (2) to cancel the functioning of the control levers and pedals.

The gate lock lever operates on three positions: A. Forward position: when the gate lock lever (2) is in forward position, the safety bar (1) is in outward position. The attachment, the travel functions and the swing functions can be operated and the safety bar does not allow the operator to leave the cab.

B. Central position: when the gate lock lever (2) is in central position, the safety bar (1) is in inward position inside the console. The attachment, the travel functions and the swing functions cannot be operated even if the engine is running. The operator may leave the cab if needed.

C. Backward position: when the gate lock lever (2) is in backward position, the safety bar (1) is in inward position, all the functions are disabled and the left hand console is fully raised. The operator can thus easily get off the cab.

NOTE: set the gate lock lever to central position if just stopping machine operation without leaving the cab. Set the gate lock lever to backward position when ending machine operation and leaving the machine.

NOTE: the engine must be started with the gate lock lever in central position. If the gate lock lever in forward position, the engine does not start.

3-40

SMIL15CEXY881AB

2

3 - CONTROLS AND INSTRUMENTS

Heating, ventilation or air-conditioning control

BB5EU2-001

1

1.

On/Off

6.

Windshield defroster

2.

Automatic

7.

Air flow direction

3.

Temperature

8.

Air recycling

4.

Ventilation

9.

Display screen

5.

Air conditioning

On/Off This push-button (1) is for turning the system On or Off. NOTICE: When the system is turned On it will operate at the same setting as the one selected previously.

KAPW1A-002

3-41

2

3 - CONTROLS AND INSTRUMENTS

Ventilation These push buttons (4) enable the air flow to be increased or reduced. To increase the flow of air, press the top button. To decrease the flow of air, press the lower button.

The segments on the display screen (9) will increase or decrease depending on the flow selected.

WSD444-001

3

GG7D18-001

4

3FGJSW-001

5

V85W49-001

6

Temperature These push buttons (3) allow the temperature to be raised or lowered within an 18 °C (64.4 °F) and 32 °C (89.6 °F).

To increase the temperature, press the up button. To lower the temperature, press the low button. The temperature reading will appear on the display screen (9).

NOTICE: The temperature reading can be displayed in degrees Celsius or degrees Fahrenheit. To select the scale required, press the two push buttons (3) simultaneously for five to ten seconds. The degrees Fahrenheit temperature will be followed by an "F".

Air recycling This button (8) allows for two different types of air circulation to be selected. Fresh air from outside or recycled air from inside. The type of circulation will be changed each time the button is pressed. Indication of the type of flow direction selected will appear on the display screen (9).

(A) Internal air circulated (B) External air enters

Air flow direction This button (7) allows four different types of air flow direction to be selected. To select the type of air flow direction, press the button (7) successively until the type of flow direction required is obtained. Indication of the type of flow direction selected will appear on the display screen (9).

3-42

3 - CONTROLS AND INSTRUMENTS

(A) Upper front distribution.

(B) Upper rear distribution.

(C) High force upper distribution and low force rear distribution.

(D) Lower rear distribution (feet) and windshield.

V85W49-002

7

W98JSC-003

8

6CSC9W-001

9

Windshield defroster This button (6) allows the windshield to be defrosted.

Press the button to defrost the windshield. The display screen will show that the defroster is working (9). To turn the defroster off, press the button again and the indication on the display screen will disappear.

NOTICE: When this button is used, the control (7) is deactivated.

Air conditioning NOTICE: when using the air conditioning, it is essential for all the operator's compartment windows, the windshield and the cab door to be kept closed. The air vents must be kept in open position.

The air conditioning can be used in two different ways: manual or automatic air conditioning.

Manual: This button (5) is used to turn the air conditioning on and off. When the air conditioning is running, confirmation is given on the display screen (9). Manual adjustments can be made using controls (3), (4), (7) and (8).

3-43

3 - CONTROLS AND INSTRUMENTS

Automatic: This button (2) is used for automatic adjustment of the volume, the direction of flow and starting or stopping of the air conditioning. “Auto” will appear on the display screen (9). In automatic mode, the only possible manual adjustment is to the temperature (3).

If a control other than the temperature control is operated, the automatic mode will be cancelled and “Auto” will disappear from the display (9). To stop the system, press buttons (1) or (2).

8TWEZ7-001

10

8TWEZ7-002

11

To obtain hot or cold air quickly: Cold air: Quit the automatic mode by pressing button (2) then press button (3) down to the minimum temperature of 18 °C (64.4 °F). Ventilation will be at maximum and cold air flow will come from the front.

Hot air: Quit the automatic mode by pressing button (2) then press button (3A) up to the maximum temperature of 32 °C (89.6 °F). Ventilation will be at maximum and the flow of hot air will come from the rear at foot level.

NOTICE: To ensure correct functioning and full effectiveness of the air conditioning system, it must be run at least once a week, even if only for a short time. For maintenance of the air conditioning circuit components, refer to page 6-1 .

3-44

3 - CONTROLS AND INSTRUMENTS

Cab internal lighting The light is located on the left-hand cab upright and is controlled by a three position switch set in the lamp base.

Positions: “On” (continuous operation), “Off” (shut-down) and intermediate position goes off 30 seconds after closing the door.

NOTICE: Make sure that the lights are switched off after use, otherwise the batteries may become discharged.

NOTE: To replace bulbs, (Refer to page 6-1).

9BWN45-001A

3-45

1

3 - CONTROLS AND INSTRUMENTS

Emergency exit hammer Located on the left-hand cab, use the hammer (1) to break the rear window, and then push the window strongly and escape outside.

Consult your NEW HOLLAND CONSTRUCTION dealer for window installation.

ATTENTION: Do not break the rear window except when it is absolutely necessary, such as to escape in an emergency.

ATTENTION: Do not place anything in front of the window.

Doing so may obstruct an emergency escape.

KUXZSM-001

1

T5BF93-001A

1

Sliding windows on door When the locks are released, the windows can be opened and closed to the left or right as required.

3-46

3 - CONTROLS AND INSTRUMENTS

Right-hand side controls

Right-hand control arm

SMIL16CEX0272EB

1.

Starter switch ( 4 positions ): ON (contact), START (engine ignition), OFF (engine shut-down) and ACC (accessory current supply).

NOTICE: when the starter key is in ON position, if the anti-theft protection has been programmed, it will be necessary to enter the password. Refer to page 4-4 ).

1

Press and release the button again to resume the engine speed set by the engine speed throttle. The "Engine idling" icon disappears.

4.

NOTE: the starter key is also used to lock the cab door, the engine hood, the front storage compartment, the side doors and the fuel tank cap.

Arm angle adjustment lever: the lever enables the control arm to be adjusted in different inclines in accordance with the operator's body profile. Hold the lever and select the desired position, and then release the lever.

NOTICE: stop the engine when adjusting the control arm.

2.

Engine speed throttle and work mode selector.

5.

Radio

3.

Engine low idle speed button: the engine low idle speed button enables to set the engine speed to low idle at a touch without moving the engine speed throttle. If operating at engine speed different from low idle, press and release the engine low idle speed button to get down the engine speed to low idle. The "Engine idling" icon appears on the message screen.

6.

One-touch wiper switch: press and hold down the switch to operate the wiper blade.

7.

Auxiliary port.

8.

USB port.

9.

Beverage cup holder

3-47

3 - CONTROLS AND INSTRUMENTS

When the machine is equipped with an auxiliary high-flow hydraulic circuit, the right-hand control lever includes: 1. Proportional switch to operate double-acting hydraulic attachments.

2. ON/OFF button to operate single-acting hydraulic attachments.

3. Engine low idle speed button.

NOTE: The auxiliary high-flow hydraulic circuit can be equipped with two alternative controls: the auxiliary pedal or the proportional switch on the right-hand control lever.

Check which type of control is actually fitted on the machine before start operating the attachment.

SMIL15CEXY838BA

3-48

2

3 - CONTROLS AND INSTRUMENTS

Cab radio

1

352C5814

NOTICE: Do not let water get into the speaker cases or the radio to avoid a breakdown. Keep the window closed when it rains and when washing the machine. Do not use benzene, paint thinner or any other solvent to clean the display. Wipe off the water with a soft, dry cloth. Do not try to disassemble the radio.

1. Power button (POWER) Push the "POWER" button to turn on the radio. The band and then then the frequency are displayed.

Push again the "POWER" button to turn off the radio.

The clock is displayed.

2. Sound adjustment (SOUND) Push the "SOUND" button to switch BAL → TRE → BAS .

- In BAL state: push the / tuning button (7) the regulate the balance.

Push the UP button to increase the right speaker volume; push the DOWN button to increase the left speaker volume. The volumes can be increased up to the level 7 maximum.

- In TRE state: push the / tuning button (7) to regulate the treble.

Push the UP button to increase the treble of 1 step; push the DOWN button to decrease the treble of 1 step. The treble can be increased up to the level 7 maximum.

- In BAS state: push the / tuning button (7) to regulate the bass.

Push the UP button to increase the bass of 1 step; push the DOWN button to decrease the bass of 1 step. The treble can be increased up to the level 7 maximum.

Push again the “SOUND” button in BAS state to end the sound adjustment.

3. Display unit The display shows the clock, radio frequency, band name and operation mode.

4. Clock/Frequency button (DISP) Push the “DISP” button to show: “Frequency” → “Clock” → “Band name”.

Each push changes the visualization.

The display returns automatically to the frequency visualization if no button is pushed within 1 second.

5. Auto store (SOUND/AUTO PRESET) Push the button to store 6 radio stations in the memory for the selected signal band (FM1, FM2, AM).

6. Choose of the preset radio stations (PRESET STATION) Push the button (1-6) to tune the radio to the stored station on the selected signal band (FM1, FM2, AM) .

To store a radio station in the memory, tune the radio to the station desired and hold down one of the button (1-6).

7. Tuning button (TUNE) Push and hold the "TUNE" button to tune automatically the radio to the next station. To stop the tuning, release and push again the button.

Push the button to increase the frequency; push the button to decrease the frequency. Hold down either button to change the frequency continuously.

8. Mode switch button (MODE) Push the button to switch AM → FM1 → FM2 → AUX → USB → BT. 9. Volume adjustment buttons (VOL , VOL ) Push the VOL button to decrease the volume; Push the VOL button to increase the volume. Hold down either button to change the volume continuously.

10. Clock adjustment (DISP) To adjust the clock, push and hold the "DISP" button when the clock is shown on the display.

- Hour adjustment With the hour on the display flashing, use the tuning button / to adjust the value.

Push the UP button to increase the value.

Push the DOWN button to decrease the value.

Pressing the “DISP” button shifts from hour to minute adjustment.

- Minute adjustment With the minutes on the display flashing, use the tuning button / to adjust the value.

Push the UP button to increase the value.

Push the DOWN button to decrease the value.

3-49

3 - CONTROLS AND INSTRUMENTS

Push the “DISP” button again to end the clock adjustment 11. REDIAL Hold down the “MODE” button (8) to redial. The message "RE" is shown on the display for 3 seconds. After redialing, the message "DL" flashes on the display and a phone ring sound is played from the speaker.

Redialing works in any kind of radio band signal. If the radio is switched off, push and hold the “MODE” button (8) to turn on the radio and redial.

12. External input jack (AUX IN) — vehicle body side Connect here a 3,5" plug audio source to play the audio from the radio speakers.

Auto preset Push the “SOUND/AUTO PRESET” button (5) to store automatically the first 6 clearly audible radio station in the 6 preset buttons.

NOTE: If a previous station was stored in the preset button, the new station replaces the old one.

External input - Audio from a portable audio device can be played through the radio speaker.

- Always keep appropriate volume for the portable audio device.

13. External input terminal (USB) - Vehicle body side Connect here an external USB audio source to play the audio from the radio speakers.

Listen to the radio 1. Turn the starter switch key to "ACC" or "ON" , then push the "POWER" button (1) to turn on the radio.

2. Select the "MW (AM)" or "FM" signal by pushing the “MODE” button (8) .

3. Select a station through a preset button (1-6) or the tuning buttons / .

37CE79DD

4. Adjust the volume with the / buttons.

2

5. Push the "POWER" button (1) to switch off the radio.

1. USB memory 2. AUX input terminal

Manual tuning

AUX

Push the UP button to increase the frequency.

Push the DOWN button to decrease the frequency.

- Push the “MODE” button (8) to switch the audio source until the message "AUX" is shown on the display.

Automatic Station Selection (Seek) Push and hold the "TUNE" button (7) to increase the frequency until the radio is tuned on a clearly audible radio station. The search stops.

Push and hold the "TUNE" button (7) to search for a radio station by decreasing the frequency.

- Connect the portable audio device to the AUX input terminal with an audio cable without resistence. The cable must have a 3,5" jack. Do not use a connection cable with the wrong size or wrong shape jack.

- The volume also can be adjusted with the volume buttons on the radio unit.

USB

Setting the preset buttons 1. Push the “MODE” button (8) to select "MW (AM)" or "FM" signal, then push the tuning buttons to select the broadcasting station to store in the radio memory.

2. Hold down the button (1-6) where to store the selected broadcasting station until the preset button number flashes three times on the display. At the preset button is now stored the selected station. If a previous station was stored in the preset button, the new station replaces the old one.

3. Repeat the steps 1 and 2 to preset other broadcasting stations.

- Files in MP3/WMA/AAC formats are supported.

- Push the “MODE” button (8) to switch the audio source until the message "USB" is shown on the display.

- Connect a USB memory to the USB input terminal.

Playable data stored in the memory is played automatically.

Button functions with USB selected as an audio source: UP /DOWN Preset 1 Preset 2 Preset 3 - short press

3-50

Folder navigation up/down Repeat the track Random track Previous track

3 - CONTROLS AND INSTRUMENTS

2. When pairing preparation is complete, the message "PA" is shown on the display and the unit enters pairing standby status.

Preset 3 - long press

Fast forward (while being pressed) Preset 4 - short press Next track Preset 4 - long press Rewind (while being pressed) Preset 5 Play/pause Volume adjustment button Volume up

3. Search for the device to pair such as a mobile phone or a portable audio device.

4. When pairing is completed successfully, the message "PO" is shown on the display. If pairing is not completed within a time limit (180 seconds) or an error occurs, the message "P×" is shown on the display. If pairing is failed, repeat from step 1 to perform paring.

Volume adjustment button Volume down

Bluetooth - Push the “MODE” button (8) to switch the audio source until the message "BT" is shown on the display.

- Pair the Bluetooth device. For details on pairing, refer to " Bluetooth Pairing"

Use of Cellular Phone Connected via Bluetooth - When the paired cellular phone receives a call, the message "CL" blinks on the display and the speaker will play the ringtone. Even if the radio is switched off, it turn automatically on.

- For details on how to use a mobile phone connected via Bluetooth , refer to " Use of Cellular Phone Connected via Bluetooth"

- To answer to the call, push any kind of radio button except from the "POWER" (1) and the volume buttons / .

Button functions with Bluetooth selected as an audio source:

- To reject a call, press the "POWER" button (1) . The call is interrupted and the radio is restored to its previous state.

Preset 3 - short press Preset 4 - short press Preset 5 Volume adjustment button

- To adjust the speaker volume during the call, push the volume adjustment buttons / . To turn on/off the microphone, push the “PRESET” button (6) .

Previous track Next track Play/pause Volume up

Volume adjustment button Volume down

- Push the "POWER" button (1) to terminate a call. The radio is restored to its previous state.

Bluetooth Pairing

- Hold down the “MODE” button (8) to redial. The message "RE" is shown on the display for 3 seconds. After redialling, the message "DL" flashes on the display and a phone ring sound is played from the speaker.

NOTICE: To use Bluetooth audio devices, the devices to be connected with a wireless connection must be registered in advance. This registration is called pairing. If a device has never been paired, pairing must be performed.

1. With "BT" shown on the display, hold down the “AUTO PRESET” button (5) . The "WA" message is shown on the display and the unit proceeds to pairing preparation.

Memory Erasure Disconnecting the battery from the vehicle electrical circuit, the radio lose the stored radio stations in the Preset buttons 1-6.

3-51

3 - CONTROLS AND INSTRUMENTS

Right-hand console

JBJS8O-002

1

1. Cigarette lighter and 24 V power supply socket: the device is active with the starter key in ON position, or while the engine is running.

To operate the cigarette lighter, push it down to engage its heating position.

4. Horn volume lowering switch: the horn volume lowering switch allows to change the volume of the horn.

Press the ON side of the switch to lower the volume of the horn. Press the OFF side of the switch to resume the normal volume of the horn.

NOTICE: keep pushing the cigarette lighter can cause serious damages to the device and to the machine electrical system.

5. 12 V power supply socket: the device is active with the starter key in ON position, or while the engine is running.

NOTICE: the electrical system may be damaged if the cigarette lighter does not return to its original position after 30 s. Pull it out manually and consult the NEW HOLLAND CONSTRUCTION dealer.

NOTICE: connect only 12 V devices to the socket. Connecting devices functioning at different voltage can cause damages to the device itself and to the electrical system.

NOTICE: connect only 24 V devices to the socket. Connecting devices functioning at different voltage can cause damages to the device itself and to the electrical system.

2. Storage tray 3. Ashtray

3-52

3 - CONTROLS AND INSTRUMENTS

Cup holder Located on the front right-hand side of the operator's seat, the cap holder is designed to hold a beverage container.

Y1MGWJ-001A

3-53

1

3 - CONTROLS AND INSTRUMENTS

Rearward controls

Fuse box Located on the left-hand site, behind the operator's seat.

UE1ERB-001A

1

UE1ERB-002A

2

FGF1OO-001A

1

Remove the cover of the fuse box.

To replace a fuse, refer to page 6-73

Magazine rack Located on the right-hand side, behind the operator’s seat.

3-54

3 - CONTROLS AND INSTRUMENTS

Refrigerated/heated compartment Located on the right-hand side, behind the operator's seat.

This compartment, associated with the air conditioning system, is designed to store different cold or hot products, drinks, etc.

NOTE: This is an insulated compartment. The compartment may not cool or heat depending on the conditions.

XKM1BK-001A

1

M377Y8-001A

1

Storage compartment Located behind the operator's seat, this compartment is used to store various objects.

NOTICE: Make sure that the weight of the stored objects is less than 10 kg (22.0 lb).

3-55

3 - CONTROLS AND INSTRUMENTS

Coat hanger hook The hook is on the rear left-hand cab upright.

NOTICE: Take care not to obscure the view with clothes that are too bulky.

5TUHIM-001A

3-56

1

3 - CONTROLS AND INSTRUMENTS

Overhead controls

Roof curtain To open the roof curtain, slide it toward the rear using the handles. To close the curtain slide it toward the front.

VHIVJ6-001A

1

D178LS-001A

1

R566HK-001A

1

Roof hatch To open the roof hatch, operate the handle and push the handle.

To close the roof hatch, pull the handle until engagement.

NOTICE: Since roof hatch opening is assisted by two gas struts, simply follow through the closing movement without pulling or trying to hold it back. Risk of hand trapping.

Sun shield (optional) The sun shield is fixed to the windshield and can easily be positioned as required.

NOTICE: risk of hand trapping.

3-57

3 - CONTROLS AND INSTRUMENTS

Exterior controls

Fuel tank WARNING Fire hazard!

When handling diesel fuel, observe the following precautions: 1. Do not smoke.

2. Never fill the tank when the engine is running.

3. Wipe up spilled fuel immediately.

Failure to comply could result in death or serious injury.

W0099A

Use suitable fuel.

NOTICE: Do not put a moisture elimination product (water draining agent) in the fuel tank. (It may damage the engine).

NOTE: Clean around the fuel cap before refuelling and do not remove the filter located in the filler orifice. (Refer to page 6-1).

NOTE: In cold weather, use fuel corresponding to the ambient temperature.

NOTICE: in cold weather, fill the fuel tank after each working day to prevent the formation of condensation.

21C635E3

1

511A2FB6

2

When installing the fuel cap, make sure that it is correctly placed in the notches and then lock it by turning it up against the stop.

NOTE: Use the ignition key to lock the fuel cap.

The fuel tank is equipped with a max level visual gauge.

3-58

3 - CONTROLS AND INSTRUMENTS

Rear view mirrors WARNING Avoid injury and/or machine damage!

Keep the mirrors clean and properly adjusted.

Failure to comply could result in death or serious injury.

W1078A

Mirror Position

SMIL16WEX0032EA

1

Visibility zone The illustrations below show the visibility zone that each rear view mirror must cover.

SMIL16WEX0031EA

3-59

2

3 - CONTROLS AND INSTRUMENTS

Mirror A (cab top) Install and adjust the mirror so that the rear left end of the machine is visible from the operator's seat.

Bolt (1) tightening torque: 71.6 - 91.2 N·m (52.8 - 67.3 lb ft) - Install the mirrors as shown in the figure.

L: 170 mm (6.7 in)

SMIL16CEX0275AB

3

SMIL16CEX0276AB

4

SMIL16CEX0278AB

5

SMIL16CEX0283AA

6

- Adjust this mirror so that the side of the machine reflects in the mirror as shown in the figure.

Mirror B (front right housing) Installing and adjust the mirror so that the rear right end is visible from the operator's seat.

- Install the mirrors at the positions shown in the figure.

L1: 350 mm (13.8 in) L2: 150 mm (5.9 in)

Adjust this mirror so that the side of the machine reflects in the mirror as shown in the figure.

3-60

3 - CONTROLS AND INSTRUMENTS

Mirror C (counterweight right) When installing this mirror, adjust it so that the right front end of the machine can be checked from the operator's seat.

- Install the mirror at the position in the figure.

L1: 185 mm (7.3 in)

SMIL16CEX0353AA

7

SMIL16CEX0280AB

8

SMIL16CEX0354AA

9

- Adjust this mirror so that the side of the machine is reflected as in the figure.

Mirror D (counterweight rear) When installing this mirror, adjust it so that the rear section of the machine can be checked from the operator's seat.

- Install the mirror at the position in the figure.

L: 147 mm (5.8 in)

- Adjust this mirror so that the rear of the machine reflects in the mirror as in the figure.

SMIL16CEX0282AB

3-61

10

3 - CONTROLS AND INSTRUMENTS

Rear view camera (optional) NOTICE: the images on the monitor (rear view camera, side camera) are auxiliary. Never operate the machine just watching the images on the monitor. The images shown and real conditions could be different: risk of collisions and unexpected accidents.

When operating the machine, always check the safety of surroundings with your own eyes and the mirrors and use the horn to signal the operations.

Also, for the sake of safety, avoid sudden operations when starting swing or travel operations.

NOTICE: keep clean the camera lens from mud, raindrops, snow, etc. to make the images clear. Use a soft damp cloth to wipe the lens clean, then dry it with a soft dry cloth. Do not scratch the camera section. This can affect the images on the monitor screen.

D112A983

1

4D5C551A

1

Front storage box This is to the front right of the upperstructure. It is used for storing emergency parts.

The storage box also gives access to the fuel tank filler pump (if equipped) and the upperstructure working light.

To open the box cover, use the pushrod of the cylinder.

The door of the box being fitted with a gas strut, follow through the opening or closing movement.

NOTICE: use the ignition key to lock the storage box cover.

NOTICE: moving parts Before operating the machine, check that the storage box cover is securely closed.

Failure to do so could cause death or serious injury.

3-62

3 - CONTROLS AND INSTRUMENTS

Side doors WARNING Moving parts!

Make sure all entry and mechanical access doors are properly closed before operating the machine.

Failure to comply could result in death or serious injury.

W0238A

Use the outside handle to open the doors. To hold the doors, open, remove the struts from their storage position and install them in the holes provided. When closing, put the struts back into their storage housing.

Use the ignition key to lock the side doors.

Right-hand door The right-hand door gives access to certain hydraulic components (pump, filter, etc.) and also to the engine fuel and oil filters.

45D0ED21

1

C4C69C5C

2

Left-hand doors The left-hand doors are mainly for obtaining access to the batteries, battery master switch, windshield washer tank, air filter, radiator, oil cooler, etc.

NOTICE: Always install the struts when the doors are open.

NOTICE: never leave tools or other objects behind the side doors.

YCRTA1-002

3-63

3

3 - CONTROLS AND INSTRUMENTS

Battery master switch NOTICE: the battery master switch must be used only for long term storage or electrical repair and welding on the machine.

Located near the batteries, open the left-hand door.

05F4B0E3

1

D6EC4F50

2

When the key of the battery master switch is in “ON” position, all electrical circuits are connected.

When the key of the battery master switch is in “OFF” position, the electrical circuits are disconnected.

NOTICE: Never turn the key of the battery master switch in “OFF” position when engine is running, the electrical systems can be damaged.

NOTICE: When the engine is stopped, always wait three minutes minimum before to place the key of the battery master switch in “OFF” position, otherwise the computer program of the hydraulic will not exit successfully.

NOTE: When the key of the battery master switch is in “OFF” position, the stations stored on the radio presets and the time set for the clock will be all cleared.

NOTE: The key can be remove from the battery master switch.

3-64

3 - CONTROLS AND INSTRUMENTS

Engine hood Opening Release the tailpieces then lift the hood to the maximum so that it gets automatically locked with the support strut.

NOTICE: access to the left side tailpiece is alongside the left track.

NOTICE: once the hood is completely opened, make sure the locking system is correctly engaged.

25376287

1

6A21BAD5

2

Closing WARNING Moving parts!

Make sure the hood is closed properly before driving the machine.

Failure to comply could result in death or serious injury.

W0280A

Lift the hood slightly, pull the support strut back lower the hood and lock it using the tailpieces.

To lock the hood, secure the front tailpiece using the ignition key.

GSVC6J-003A

3-65

3

3 - CONTROLS AND INSTRUMENTS

Lower panels WARNING Moving parts!

Make sure the lower panels are properly closed before driving the machine.

Failure to comply could result in death or serious injury.

W0910A

Located under the upperstructure frame, these panels provide access to certain machine components.

ATTENTION: Do not run the machine with the panels removed.

D5CW65-001A

1

JMSFSF-001Z

1

Windshield washer reservoir This reservoir, located in the rear left-hand compartment, is equipped with an electric pump which is operated from the control panel.

NOTICE: Never operate the windshield washer control when the reservoir is empty. This could cause damage to the electric pump.

Remove the cap to add windshield washing fluid.

NOTE: In cold weather, add anti-freeze to the windshield washer water.

The reservoir can be lifted out of its support.

3-66

3 - CONTROLS AND INSTRUMENTS

Safety valves (optional) Service specifications Check by your NEW HOLLAND CONSTRUCTION Dealer: Every 6 months The role of the safety valve is to stop the attachment from dropping due to valve spool leakage in neutral position or in the event of a line or hose accidentally breaking. In the latter event, they also ensure that the attachment may be lowered gently to the ground.

On boom cylinders

C5CI3R-001A

1

A48SZS-001A

1

Optional tool supply valves (optional) Located on each side of the end of the arm, these valves are used to ensure oil supply to optional tools. These valves have two positions, open/closed.

3-67

3 - CONTROLS AND INSTRUMENTS

Fuel tank filler pump (if equipped) WARNING Fire hazard!

When handling diesel fuel, observe the following precautions: 1. Do not smoke.

2. Never fill the tank when the engine is running.

3. Wipe up spilled fuel immediately.

Failure to comply could result in death or serious injury.

W0099A

NOTICE: Do not put a moisture elimination product (water draining agent) in the fuel tank. It may damage the engine.

NOTICE: The fuel tank filler pump is located inside the storage box on the right front of the upperstructure and shall be used for fuel only. Use suitable fuel.

1. Park the machine on flat, horizontal ground, stop the engine and turn the starter key to ON position.

2. Take the inlet pipe out of the front storage box.

823D2887

1

3. Measure the height of the drum and place the identification clamp (1) of the suction tube at a length slightly less than that of the drum height.

4. Make sure that the end strainer of the suction tube is correctly attached and then insert the suction tube in the drum.

SMIL14CEX2515AB

5. Remove the fuel tank filler cap.

WARNING Burn hazard!

If the filler cap remains on during the refueling process, removing the cap after refueling could cause an accident. To reduce this risk, ALWAYS remove the fuel tank filler cap before refueling with the fuel tank filling pump.

Failure to comply could result in death or serious injury.

W0247A

F2F6DB02

3-68

3

2

3 - CONTROLS AND INSTRUMENTS

6. Select the filling method using the selector switch located on the right side of the filling pump: ○ Auto mode: the pump stops filling automatically and the audible alarm sounds when the fuel tank is full. ○ Manual mode: the filling shall be monitored from the fuel tank gauge and shall be stopped when the fuel reaches the maximum level.

8VHZ5J-004

4

7. Turn the main switch of the pump to ON position. Filling begins.

8. When the fuel tank is full, turn the main switch of the pump to OFF position. In Auto mode, the audible alarm device will cease to function.

NOTE: It is possible to stop filling at any time by turning the main switch of the pump to OFF position.

9. Run the pump for a few moments to empty the pipe outside the drum. Clean and replace the inlet pipe in the front storage box.

10. Refit the fuel tank filler cap.

9E185F53

11. Turn the starter key to OFF position.

NOTE: The pump is equipped with a 10 A fuse.

3-69

5

3 - CONTROLS AND INSTRUMENTS

3-70

4 - OPERATING INSTRUCTIONS

4 - OPERATING INSTRUCTIONS###_4_### Commissioning the unit

Cab - Operating Before using the machine

14. Find out about current safety measures in use on the work site.

DANGER

15. Work out a convenient means of escape from the machine (emergency exit via the windshield, the rear window glass) in the event of the machine turning over or tipping over or the cab door being jammed.

Improper operation or service of this machine can result in an accident.

Do not operate this machine or perform any lubrication, maintenance, or repair on it until you have read and understood the operation, lubrication, maintenance, and repair information.

Failure to comply will result in death or serious injury.

16. Before undertaking any travel or working operations during hours of darkness, make sure the lighting and signalling equipment is fully operative.

Operating the machine

D0010A

WARNING Before operating this machine, be sure to do the following: 1.

Check the level of all fluids (engine oil, hydraulic fluid and coolant) and make sure that the fluids and lubricants are suitable for prevailing conditions.

Driving hazard!

Check all controls and safety devices in a safe, open area before starting work.

Failure to comply could result in death or serious injury.

2.

Carry out the daily maintenance operations. (Refer to page 6-1 ).

When operating the machine, be sure to do the following:

3.

Inspect the machine, look for any signs of possible leakage and check the hoses. Tighten or replace as necessary.

1.

When starting the engine, be sure to use the correct procedure for the prevailing weather conditions. (Refer to page 4-7 ).

4.

Refer to page 4-3 if the machine is new or if the engine has been reconditioned.

2.

Regularly consult the hourmeter to ensure that all servicing operations are carried out punctually.

5.

Check the track assemblies. (Refer to page 6-52 ).

3.

6.

Clean the steps and access handles. Grease, oil, mud or ice (in winter) on the steps and access handles can causes accidents. Make sure they are kept clean at all times.

If you use your machine in particularly harsh conditions (dusty or corrosive atmosphere), the servicing intervals should be reduced accordingly.

4.

Take note of the locations of pipes/cables before starting work.

5.

Do not work near overhead high-voltage electric lines without checking beforehand that all necessary measures have been taken to respect the minimum distances: Less than 57 000 volts: 4 m (13 ft) More than 57 000 volts: 5 m (16.4 ft)

6.

When working on a public highway, use standard traffic signs and take into consideration the working range of the upperstructure and its attachments. Local regulations stipulate the number, type and location of reflector strips.

7.

Never operate the working or travel controls unless you are properly seated in the operator's seat with the seat belt correctly fastened.

8.

Modify your driving to suit the type of work and working conditions.

7.

Clean or replace any decals which are illegible. (Refer to page 2-15 ).

8.

Make sure that the engine hood and the side doors are properly closed and latched.

9.

Secure the cab door in either fully closed or fully opened position. (Refer to page 3-1).

10. Remove any obstructions which hinder visibility.

Clean the windshield, the windows and the rear view mirrors.

11. Check that no tools or other items have been left on the machine (be it on the undercarriage or the upperstructure) or in the operator's compartment.

12. Make sure nobody is on or under the machine. The operator must be alone on the machine.

W0248A

13. Make sure nobody is standing in the machine working area.

4-1

4 - OPERATING INSTRUCTIONS

9.

Do not allow anyone within the machine's operating radius. Stop all operations until everyone has moved away.

18. Avoid running the engine in a confined space. If there is no alternative, proper ventilation must be provided at all times.

10. Refer to page4-3 if the machine is new or if the engine has been reconditioned.

19. Dust, smoke or mist can reduce visibility and cause an accident. Reduce speed or come to a complete halt until visibility has improved.

11. Operate all controls gradually to ensure smooth machine operation.

13. Refer to page 5-1 when driving the machine onto a trailer.

20. In the event of an operation problem or failure, move the machine to a safe place, lower the attachment to the ground, stop the engine, remove the ignition key.

Locate the problem, report it if necessary and take the necessary steps to warn others not to attempt to operate the machine.

14. Refer to page 4-17 when it is necessary to lift the machine.

21. Do not stop the engine without taking prevailing weather conditions into consideration.

15. Refer to page 5-7 when it is necessary to tow the machine.

22. Refer to page 4-29 when you have to park the machine.

16. In some configurations, the working range of the attachment allows the tool to interfere with the machine. Always maintain a safe minimum distance between the tool and the machine.

23. Whenever load handling operations are to be carried out, it is imperative to adhere strictly to the instructions given in this manual and local legislation. (Refer to page 4-17 ).

12. Refer to page 4-21 if the machine will be standing in water during use.

17. Never use the attachment for sweeping the ground to level out rubble or push objects (transversal stress on the attachment).

4-2

4 - OPERATING INSTRUCTIONS

Break-in period Your machine will last longer and will give better and more economical performance if you pay particular attention to the engine during the first twenty hours of operation.

During this period: • Warm up the engine before using it under load.

• Do not run the engine for a long period at idle speed.

• Check all instruments frequently.

• Check the oil levels and coolant solution level frequently.

During the run-in period, the following checks and servicing operations should be carried out in addition to those specified in the service schedule:

After the first 50 hours Check the pad screws are tightened to the correct torque.

(Refer to page 6-52 ).

Check all nuts and screws are tightened to the correct torque. (Refer to page 6-72 ).

After the first 250 hours Replace the pilot circuit filter and the return filter. (Refer to page 6-36 ).

Replace the oil in the travel reduction gears. (Refer to page 6-51 ).

Replace the oil in the swing reduction gear. (Refer to page 6-49 ).

4-3

4 - OPERATING INSTRUCTIONS

Starting the unit

Anti-theft protection To prevent the machine from being stolen it is possible to use the anti-theft protection, which makes it necessary for a special code to be entered before the machine can be operated.

To configure the anti-theft protection, consult your NEW HOLLAND CONSTRUCTION Dealer.

The effects of the device are: • The engine runs at idle speed.

• The audible alarm device will sound.

• The engine stops if the machine is handled.

Once the machine has been configured, a special access code has to be recorded which must be entered whenever you start the engine.

NOTICE: once the code has been recorded, do not forget it, as it can not be changed without consulting your NEW HOLLAND CONSTRUCTION Dealer.

2. "Password?" and 4 boxes are displayed on the display screen.

3RW3PD-003

1

3. - Use the following buttons to record a code.

- Move the cursor to the left with the front glass washer button (1).

- Move the cursor to the right with the working light button (2).

- Increase the value (0, 1, 2, 3...) with the front glass wiper button (3).

- Decrease the value (...3, 2, 1, 0) with the engine idling select button (4).

84C1BFFB

4. After entering all 4 digits, press the menu button (5) to register the password code. The screen returns to the normal display.

NOTICE: be sure to keep a record of the code number.

4-4

2

4 - OPERATING INSTRUCTIONS

Using the anti-theft protection The anti-theft protection has to be activated when you are shutting down the engine. Turn the ignition key from “On” to “Off” for about 2 seconds at a time until the audible alarm device sounds. The icon of the anti-theft protection is displayed on the screen, the anti-theft protection is activated, now the access code will have to be entered when starting the engine.

You are not obliged to activate the anti-theft protection. In that case all you have to do is to turn the ignition key to the “Off” position when shutting down the engine. In that configuration, it will not be necessary to enter the code when starting the engine.

3

SMIL16CEX0636AA

Entering the access code If the anti-theft protection was activated the last time the engine was shut down, it will then be necessary to enter the access code before being able start it again.

AZ8P3X-001

4

1. Turn the ignition key to the “On” position.

2. The message "Password?" and four boxes will appear on the display screen.

3. Enter the code in the same manner as during registration. Once all four digits have been entered, validate with the button (5).

E1E640D2

4-5

5

4 - OPERATING INSTRUCTIONS

If the access code has been entered correctly, the icon of the anti-theft protection will disappear from the screen and it will be possible to start the engine.

If the code is wrong or if the code is different from the one registered, the message “Error” is displayed, the operation has to be restarted.

Place the ignition key in the “Off” position and repeat Steps 1 to 3.

NOTE: If the anti-theft protection was activated the last time the engine was turned off, it will still be possible to start the machine without the access code, or with the wrong code, but the engine will run at idle speed, and will stop if the machine is handled.

4-6

AZ8P3X-002

6

4 - OPERATING INSTRUCTIONS

Starting the engine NOTE: If the machine has been out of use for some time.

(Refer to page 6-89 ).

NOTE: Refer to page 6-75 if you have to start the engine using booster batteries.

1. Take up position correctly in the operator's seat with the seat belt correctly fastened. (Refer to page 3-5 ).

2. Make sure the function cancellation lever is in the central position (safety bar in inward position).

HISNJU-003

1

3. Make sure the engine throttle button (1) is in low idle position. In cold weather, leave it in half-way position.

4. Turn the ignition key (2) to “On” position.

5. If necessary, enter the anti-theft code. (Refer to page 4-4 ).

In cold weather, the "Engine pre heat" icon appears on the systems display panel.

4B47404C

2

76D19D8C

3

6. Sound the horn button on the left-hand control lever to give warning of your intention to start the machine.

4-7

4 - OPERATING INSTRUCTIONS

7. When the icon disappears, turn the ignition key to the “Start” position. Release the key as soon as the engine starts to turn. If the engine stops, wait about a minute and perform the operation again.

NOTICE: Do not operate the starter motor for more than ten seconds at one time. Do not operate the starter motor when the engine is running.

HISNJU-005

4

HISNJU-006

5

BDBC08E9

6

8. Run the engine until the "Automatic heating" icon disappears from the systems display panel.

9. Push the function cancellation lever forward (safety bar in outward position).

NOTE: Check the systems display and console frequently while the engine is running. (Refer to page 4-10).

NOTICE: This machine is equipped with a new type of engine incorporating a high-pressure fuel injection system which reduces the emission to the environment and respects the regulations applicable to level 4 engine emissions. Starting this engine takes about 1 second before stabilisation.

NOTICE: If the engine does not start at the first attempt, operate the starter motor for 10 seconds then wait for 1 to 2 minutes before retrying. When cold, the engine is at times difficult to start. But in all cases, do not operate the starter motor for more than 10 seconds.

4-8

4 - OPERATING INSTRUCTIONS

Bringing the machine up to operating temperature NOTICE: Normal operating temperature of the hydraulic fluid is between 50 °C (122.0 °F) and 80 °C (176.0 °F), in the middle of the temperature indicator.

After starting the engine and before using the machine, allow the hydraulic fluid to reach a temperature of 20 °C (68.0 °F), as indicated by the appearance of the first two segments on the hydraulic fluid temperature indicator. (Refer to page 3-20 ).

Engine automatic warm-up Once the engine has started, the warming-up process begins automatically. At first, engine speed is held at a predetermined, low level. As the temperature increases, engine speed increases in proportion. It is possible to interrupt the warming-up process at any time, simply by manually changing engine speed or by operating one of the control levers. Warming-up takes approximately 5 to 10 minutes.

Manual engine warm-up With the engine throttle button a quarter open, start the engine and allow it to run approximately for 5 to 10 minutes.

When the coolant temperature reaches the second segment, carry out the hydraulic fluid warm-up procedure.

Hydraulic fluid warm-up 1. Turn the engine throttle button to half-open position. Push the function cancellation lever forward (safety bar in outward position). Operate the bucket control slowly until the bucket is completely closed. Operate the arm retracting control slowly until the arm is completely retracted and hold the control in this position for 30 seconds.

During this time the temperature of the hydraulic fluid will increase.

2. After 30 seconds, extend the arm completely and hold the control in this position a further 30 seconds.

3. Continue the arm extending and retracting procedure until the temperature rises (first two segments of the temperature indicator).

4. Operate the travel and attachment controls three or four times to circulate the hydraulic fluid.

4-9

4 - OPERATING INSTRUCTIONS

Engine operation WARNING Hot liquid under pressure!

Fuel in the high pressure fuel line is still under pressure immediately after you shut down the engine.

Before performing any maintenance or inspection, wait for 2 minutes after engine shutdown to allow the pressure to drop.

Failure to comply could result in death or serious injury.

W0249A

WARNING Electrical shock hazard!

High voltage is charged to the controller and/or to the injector while the engine is running and immediately after shutdown. DO NOT touch the controller or the injector. Consult your dealer if it is necessary to touch these parts for maintenance purposes.

Failure to comply could result in death or serious injury.

W0250A

When the engine has started and before beginning work, the following procedure must be observed: 1. Let the engine idle for about five minutes until it has warmed up.

2. Move the engine throttle button to the maximum speed position.

Once normal operating temperature has been reached, check the following: • The exhaust smoke is normal.

• There is no abnormal noise or vibration.

• There are no oil, fuel or water leaks.

The engine should be run at full speed when operating conditions permit.

The operating speed of the machine and of the attachment should be controlled by means of the control levers.

Check the systems display and console regularly.

Stop the engine immediately if one of the following situations occurs: • Sudden increase or decrease in engine speed.

• Abnormal noise.

• Black smoke at the exhaust.

• A message appears on the display screen and the audible alarm device sounds.

4-10

4 - OPERATING INSTRUCTIONS

Operating the machine in hot or cold weather In cold weather Follow the recommendations shown below: Batteries • They should be fully charged.

Fuel • To prevent condensation forming and water getting into the fuel system, fill the fuel tank after each day's work and drain off any water before starting the next day's work.

• To prevent crystals forming at -2 °C (35.6 °F), use fuel which is rated for the ambient temperature or add an appropriate antifreeze to the fuel.

Engine oil • It should be of the right viscosity for the ambient temperature.

Hydraulic fluid • The viscosity must correspond to the ambient temperature conditions.

Coolant solution • It must have specifications corresponding to the ambient temperature.

In hot weather Follow the recommendations shown below: • Keep the coolant at the correct level in the coolant reservoir and in the radiator.

• Use the correct solution of ethylene glycol and water in the cooling system.

• Test the radiator cap before hot weather starts. Replace the cap as required.

• Clean all dirt and debris from the radiator, cooler and engine area.

• Check the condition of the fan drive belt.

• Check the dust valve in the air cleaner frequently during extreme dust conditions.

• Use lubricants of the correct viscosity.

4-11

4 - OPERATING INSTRUCTIONS

Machine operation Operating instructions WARNING Misuse hazard!

Follow the operating instructions in this chapter. Any other practice that has not received the prior approval of the manufacturer is considered to be strictly forbidden.

Failure to comply could result in death or serious injury.

W0281A

Watch carefully and make sure you are aware of places where other people are working in your work area. Keep all other people away from the machine. Serious injury can result if these instructions are not followed.

When climbing up a slope, place the bucket about 40 cm (15.7 in) above the ground. When travelling down a slope it is recommended to place the bucket on the ground to prevent the machine from sliding.

Take note of the locations of pipes/cables before starting work. Electrical cables, gas and water pipes and other underground installations can cause serious injury.

Avoid turning the machine on steep slopes.

Modify your driving to suit working conditions (sloping or rough ground), the nature of the ground and weather conditions.

Never swing the upperstructure on slopes of 15 ° in the direction of travel or 10 ° at right angles to the direction of travel.

The following operations are likely to damage the machine. You are therefore advised to avoid them:

On steeply sloping ground, keep engine at maximum speed.

• Excavation using the weight of the machine as a force of impact.

When travelling at right angles to the slope, move on to the slope at low speed. Never reduce engine speed when travelling down slopes.

• Excavation using the machine’s travel force.

Holes, obstacles, debris and other danger risks in the working area can cause serious injury. Inspect and note all possible risks before driving the machine in a new working area.

NOTICE: do not operate the engine with the machine at 35 °. The engine or hydraulic devices may be damaged.

Do not work near overhead high-voltage electric lines without checking beforehand that all necessary measures have been taken to respect the minimum distances: Less than 57 000 volts: 4 m (13 ft).

More than 57 000 volts: 5 m (16.4 ft).

Operation

The maximum slope climbing ability is 35 °( 70 %). This value varies depending on the track type and the road surface, limit travelling to slopes of 30 ° or less.

1. Sit in the operator's seat and adjust it so that all the controls are readily accessible then fasten your safety belt.

2. Make sure the cab door is firmly latched in the open or closed position.

Never hit or push material with the sides of the bucket.

Never sweep the ground with the bucket to level rubble.

When operating the control levers, a whistling sound will be heard if the control lever is held in position while the corresponding cylinder is at the end of its stroke. In this case release the control lever.

If earth or mud stays stuck inside the bucket, open and close the bucket several times so as to loosen the earth or the mud.

3. Sound the horn.

4. Start the engine, taking into consideration the prevailing weather conditions.

5. Check all indicator lamps and gauges are operating correctly.

6. Push the function cancellation lever forward (safety bar in outward position).

7. Try out all the controls in a safe, open area.

After work, remove any mud and clean the machine.

When using the upperstructure swing, never change the direction of swing too suddenly.

4-12

4 - OPERATING INSTRUCTIONS

Stopping the unit

Stopping the engine 1. Lower the attachment until it is resting on the ground.

2. Turn the engine throttle button (1) to low idle position and let the engine run for 5 minutes or so.

NOTICE: Idle the engine for about 5 minutes.

NOTICE: Always let the engine run at idle before switching off completely, except in emergency situations.

3. Turn the ignition key (2) to the “Off” position.

NOTE: To activate the anti-theft protection when stopping the engine, (refer to page 4-4).

NOTE: When stopping the engine for a long time, refer to page 4-29 .

4B47404C

1

9003522C

2

In the event of an emergency In the event of an emergency or if it is not possible to stop the engine using the ignition key, press the emergency shut-down switch on the left-hand control arm.

NOTICE: this switch should only be used in case of an emergency. Do not use it on a day-to-day basis to stop the engine

4-13

4 - OPERATING INSTRUCTIONS

Moving the unit

Machine travel WARNING Controls can be reversed!

In the normal travel position, the operator's compartment is above the idler wheels and the travel reduction gears are to the rear of the upper structure. If the upper structure is turned 180 degrees in relation to the undercarriage, the controls are reversed.

Failure to comply could result in death or serious injury.

W0289A

NOTICE: before undertaking any travel, raise the attachment.

NOTE: Travel speed depends on the tilting angle of the travel control levers and pedals and the speed travel mode selected.

NOTE: The different travel configurations described hereafter are with the travel reduction gears to the rear of the upperstructure.

37A022D6

1

Straight line travel (forward travel) Press the two pedals (or push the two levers) forward at the same time.

DAYWLE-001

2

Straight line travel (reverse travel) Press the two pedals (or push the two levers) rearward at the same time.

TVJAZI-002

4-14

3

4 - OPERATING INSTRUCTIONS

Turning to the left (forward travel) Simply press the right-hand pedal or the right-hand lever forward.

3USM2U-001

4

VEWP8J-001

5

ZTP4TE-001

6

6J6E38-001

7

Turning to the right (forward travel) Simply press the left-hand pedal or the left-hand lever forward.

Turning to the left (reverse travel) Simply press the right-hand pedal or the right-hand lever rearward.

Turning to the right (reverse travel) Simply press the left-hand pedal or the left-hand lever rearward.

4-15

4 - OPERATING INSTRUCTIONS

Turning on the spot, to the right Press the left-hand pedal or the left-hand lever forward and at the same time press the right-hand pedal or the right-hand lever rearward.

NOTICE: turning on the spot cannot be done if high speed travel is selected.

CMK584-001

8

ZOCMTZ-001

9

Turning on the spot, to the left Press the right-hand pedal or the right-hand lever forward and at the same time press the left-hand pedal or the lefthand lever rearward.

NOTICE: turning on the spot cannot be done if high speed travel is selected.

Gradual turn on the move Press one of the pedals or one of the levers and, at the same time, press the other pedal or the other lever in the same direction, but slightly harder.

Stopping travel To come to a complete halt, simply release the levers or pedals and they will return to neutral.

R9GISV-001

4-16

10

4 - OPERATING INSTRUCTIONS

Handling the machine WARNING Improper operation or service of this machine can result in an accident.

Assign a supervisor to direct worksite operations. Agree on all safety measures, procedures, and suitable hand signals.

Failure to comply could result in death or serious injury.

W0287A

WARNING Crushing hazard!

The lifting systems must be operated by qualified personnel who are aware of the correct procedures to follow. Make sure all lifting equipment is in good condition, and all hooks are equipped with safety latches.

Failure to comply could result in death or serious injury.

W0256A

WARNING Crushing hazard!

This operation may be dangerous. You are advised to wear suitable clothing and respect all relevant safety messages.

Failure to comply could result in death or serious injury.

W0283A

WARNING Hazard to bystanders!

ALWAYS make sure the work area is clear of bystanders and domestic animals before starting this procedure. Know the full area of movement of the machine. Do not permit anyone to enter the area of movement during this procedure.

Failure to comply could result in death or serious injury.

W0245A

4-17

4 - OPERATING INSTRUCTIONS

Retract the attachment, bucket and arm cylinders fully extended then place the attachment on the ground. Shutdown the engine and leave the operator’s compartment.

NOTICE: before handling the machine, make sure the slings are in perfect condition and that they are capable of supporting the weight of the machine. (Refer to page 8-10 NOTICE: it is imperative to use the sling points indicated on the machine decals. (Refer to page 2-15).

NOTICE: The machine must be handled very slowly and horizontally.

1

SMIL15CEX0813AA

3OS524-002

4-18

2

4 - OPERATING INSTRUCTIONS

Load handling WARNING Crushing hazard!

During load handling operations, it is very important to adhere strictly to the instructions given in this manual and local legislation.

Failure to comply could result in death or serious injury.

W0257A

WARNING Equipment failure could cause accident or injury!

Do not use the hook end of the coupler when lifting loads. The sling can come out of the coupler and the load can fall.

Failure to comply could result in death or serious injury.

W0221A

WARNING Falling object hazard!

Never weld hooks or lugs on the bottom plate of the bucket for handling operations. The connecting rod eye is the only authorized attachment point. Always have a bucket installed when using the connecting rod eye.

Failure to comply could result in death or serious injury.

W0246A

NOTICE: this machine is not a crane. Be very careful when you lift a load.

NOTICE: the loads given are valid for the total working range height at the reach point indicated.

When lifting loads, the slings and chains must be attached to the load handling eye on the bucket.

The load handling chart (located in the cab) shows the different permitted loads which can be lifted, depending on the reach and the type of attachment on the machine.

The machine must be on a flat level, hard surface.

Fasten the load to the lift eye on the bucket control rod.

Never weld a hook or lug to the bottom plate of the bucket.

F8OZ9G-001

1

If this machine is to be used to lift loads, for safety purposes, it is recommended that the machine is properly equipped.

Contact your NEW HOLLAND CONSTRUCTION dealer and install a Hose Burst Check Valve on your machine’s boom cylinders. This system prevents the sudden lowering of the load in the event of a failure of a hydraulic hose, line, or fitting in the boom hydraulic system. Such a failure can cause personal injury or death.

• Use slings and chains with enough durability for load being lifted, together with a safety hook with lock.

• Check that the safety valve is operating correctly. In accordance with current regulations and/or manufacturer's instructions, the pressure setting must be checked every 6 months. Consult your NEW HOLLAND CONSTRUCTION dealer.

• Know and understand each signal from the signal person before you start.

• Always know the location of all persons in your work area before you start.

4-19

4 - OPERATING INSTRUCTIONS

• Make certain there is no damage to the lifting device and rigging parts.

• Make certain the lifting device has the appropriate tensile strength for the load being lifted.

• Do not exceed either the radius or the height restrictions shown on the lift capacity charts posted in the cab.

• Be careful to balance the load correctly.

• Switch the overload indicator switch to the "ON" position.

• Select working mode "H" (see page Right-hand control arm).

• Operate the controls smoothly and operate the machine and its attachments correctly.

• Stabilize the load a few centimeters above the ground and check that it is well balanced before moving it.

• Face the upper structure in the same direction as the undercarriage.

• Hold the load as low as possible and close to the undercarriage and ground.

• Always travel at low speed.

• Always move the load slowly. Do not move the load over the top of persons. Keep all persons away from the load.

• When the load is raised, keep all persons away until the load is placed on blocks or on the ground.

NOTICE: it is extremely dangerous if the load lifted begins to swing. The upper structure should be centered over the load to help prevent dangerous swinging.

4-20

4 - OPERATING INSTRUCTIONS

Operating the machine Operating the machine in water Make sure that the ground can support the weight of the machine and the machine is stable during its movements.

Only the undercarriage must be below water level. The maximum water level can be up to the height of the tracks is 0.80 m (31.50 in).

NOTICE: never work in water if the water level is higher than the tracks.

Before working in water, grease the attachment linkage, turntable bearing and turntable bearing teeth generously.

NOTICE: do not operate in a fast flowing stream.

66B01093

1

Operating the machine on sloping ground WARNING Driving hazard!

Hillside operations can be dangerous. Rain, snow, ice, loose gravel, or soft ground, etc. can change the ground conditions. You must make a judgment if it is safe to operate your machine on any hillside or ramp.

Failure to comply could result in death or serious injury.

W0144A

WARNING Overturning hazard!

Before parking the machine, make sure the ground is stable. Plan the worksite so that the ground is flat, hard, and level.

Failure to comply could result in death or serious injury.

W0258A

During hillside operations, be extra careful.

• Make sure that the low speed travel is selected.

• When digging on a slope, avoid swinging the upperstructure towards the bottom of the slope with the backhoe bucket full.

• Always keep the travel reduction gears pointing down towards the bottom of the slope.

• Always travel in the same direction as the slope, to prevent the machine from turning over.

4-21

4 - OPERATING INSTRUCTIONS

Operating the backhoe bucket Use the H work mode for general digging and truck loading operations.

Use the SP work mode for heavy digging operation.

Filling Fill the backhoe bucket by manoeuvring the arm.

Keep the bottom of the backhoe bucket parallel to the cut.

The backhoe bucket teeth and blade must cut the ground like the blade of a knife.

The depth of dig varies depending on the type of material.

Excavating method

2

PDH0493MTBP1

UJAY1P-002

3

1. Correct 2. Incorrect. The backhoe bucket will dig in and cause a stall.

3. Incorrect. The backhoe bucket is pushed upwards. This will also increase the cycle time.

4-22

4 - OPERATING INSTRUCTIONS

Lowering the attachment in the event of a failure If the engine breaks down, use the following procedure to lower the attachment: 1. Turn the ignition key to the “On” position.

85F4E91C

1

BDBC08E9

2

B3BD300D

3

2. Push the function cancellation lever forward (safety bar in outward position).

3. Place the control lever(s) in the position corresponding to the downward movement required.

4-23

4 - OPERATING INSTRUCTIONS

Auxiliary hydraulic circuits Consult your NEW HOLLAND CONSTRUCTION Dealer to select the optional accessory compatible with your machine and to correctly adjust the flow required for its use.

NOTICE: To prevent failure or damage to the tool, make sure that you select the correct circuit configuration and flow rate for the tool.

Hydraulic breaker or high flow hydraulic circuit configuration Your machine has two types of auxiliary hydraulic circuit. One circuit is for single flow equipment, such as hydraulic breakers. The second type of circuit is intended for use with single flow or double flow with continuous flow or for use with double flow such as demolition concrete crushers, etc.

Pedal type 1. Make the necessary tool connections and then, using a hexagonal wrench, open the supply valves located at the tip of the arm, left-hand and right-hand side.

VSLYI8-015

1

A44FD67E

2

2. Switch (1) located on the front right-hand console, corresponding to the hydraulic breaker.

Every time the switch (1) is pressed, one of the different types of flow patterns recorded for the pump can be selected. For flow setting method, refer to page 3-27.

3. The icon of the accessory associated to each type of flow on the screen.

SMIL16CEX0637AA

4-24

3

4 - OPERATING INSTRUCTIONS

4. After switch (1) has been operated, the set flow will be displayed for a set amount of time.

SMIL16CEX0638AA

4

SMIL16CEX0639AA

5

NOTE: To prevent failure or damage to the tool, make sure that you select the correct circuit configuration and flow rate and pressure for the tool.

5. Unlock the pedal and engage the locking pin (1).

SNKQ6K-002

6

VOHLGR-005

7

6. Use the control pedal to operate the hydraulic breaker.

NOTICE: In Bucket mode, do not carry out operation using auxiliary line. If you do that the warning message “Auxiliary set-up required” will be displayed with alarm sound. Stop operation immediately and carry out auxiliary set-up.

4-25

4 - OPERATING INSTRUCTIONS

Multi-purpose circuit with pressure adjuster Pedal type 1. Make the necessary tool connections and then, using a hexagonal wrench, open the supply valves located at the tip of the arm, left-hand and right-hand side.

VOHLGR-016

8

2. Switch (1) located on the right-hand console upwards, corresponding to the demolition grab.

Every time the switch (1) is pressed, one of the different types of flow patterns recorded for the pump can be selected. For the flow and pressure setting method, refer to page 3-27.

A44FD67E

9

3. The icon of the accessory associated to each type of flow appears on the screen.

SMIL16CEX1056AA

10

SMIL16CEX0686AA

11

4. After switch (1) has been operated, the set flow and pressure will be displayed for a set amount of time.

4-26

4 - OPERATING INSTRUCTIONS

NOTE: To prevent failure or damage to the tool, make sure that you select the correct circuit configuration and flow rate and pressure for the tool.

12

SMIL16CEX1057AA

5. Unlock the pedal.

VSLYI8-004

13

6. Use the control pedal to operate the concrete crusher.

NOTICE: in bucket mode, do not carry out operation using auxiliary line. If you do that, the warning message “Auxiliary set-up required” will be displayed with intermittent whistle sound. Stop operation immediately and carry out auxiliary set-up.

NOTE: To prevent failure or damage to the tool, make sure that you select the correct circuit configuration and flow rate and pressure for the tool.

VSLYI8-005A

14

Operating Controls (Right hand proportional switch) Use the ON-OFF button (1) located on the right-hand control lever to operate a single-acting hydraulic attachment with a continuous flow.

Use the proportional switch located on the right-hand control lever to operate a double-acting hydraulic attachment with a variable power.

NOTICE: If not using any hydraulic attachment, do not operate controls for auxiliary hydraulic circuits.

SMIL15CEXY965AB

4-27

15

4 - OPERATING INSTRUCTIONS

Setting ranges for auxiliary high-flow hydraulic circuit The maximum flow rate of the auxiliary high-flow hydraulic circuit can be set by monitor. The setting ranges are related to the circuit mode selected by the specific page. If breaker page has been selected (Single-acting mode), the maximum flow rate can be selected within the steps in the left column of the table below. If crusher page has been selected (Double-acting mode), the maximum flow rate can be selected within the steps either in the left column or in the right column of the table below.

NOTE: all the values for maximum flow rate are related to the SP work mode. If the auxiliary high-flow hydraulic circuit is used with a different work mode the actual flow will be lower.

1 flow 210 L/min (55.476 US gpm) 196 L/min (51.778 US gpm) 182 L/min (48.079 US gpm) 166 L/min (43.853 US gpm) 146 L/min (38.569 US gpm) 129 L/min (34.078 US gpm) 111 L/min (29.323 US gpm) 94 L/min (24.832 US gpm) 74 L/min (19.549 US gpm) 50 L/min (13.209 US gpm)

2 flows 420 L/min 406 L/min 392 L/min 376 L/min 356 L/min 339 L/min 321 L/min 304 L/min 284 L/min 260 L/min

(110.952 US gpm) (107.254 US gpm) (103.555 US gpm) (99.329 US gpm) (94.045 US gpm) (89.554 US gpm) (84.799 US gpm) (80.308 US gpm) (75.025 US gpm) (68.685 US gpm)

The setting of the working pressure of the auxiliary high-flow hydraulic circuit shall be done either manually or by monitor depending upon the machine provision.

For the Single-acting circuit and for the Multi-function circuit the working pressure shall be set manually by the relief valve located behind the boom foot.

NOTICE: the Multi-function circuit can be optionally provided with the monitor setting of the working pressure. The working pressure of the circuit can be thus selected in the range 14.0 - 34.5 MPa (2030.7 - 5004.2 psi) by steps of 0.5 MPa (72.5 psi).

NOTE: the setting capability is of ten flow rate/pressure combinations.

For the Double-acting circuit the working pressure shall be set manually by the port relief valves on the relevant section of the control valve.

4-28

4 - OPERATING INSTRUCTIONS

Parking the unit

Parking the machine 1. Position the machine on flat, level ground, away from soft ground, excavations or poorly shored cavities.

2. Place the upperstructure frame in line with the undercarriage, retract the attachment, dig the bucket into the ground to anchor it.

3. Turn the engine throttle button to low idle position and let the engine run for approximately five minutes.

4. If necessary, activate the anti-theft protection. (Refer to page 4-4).

E0DDB3F4

1

85F4E91C

2

5. Stop the engine, remove the ignition key.

6. Place the function cancellation lever in the central position (safety bar in inward position).

GHN2P4-004

4-29

3

4 - OPERATING INSTRUCTIONS

7. Lock the operator's compartment door and make sure that the hoods, lower panels and side doors are properly fastened.

NOTICE: check that the no part of the machine is encroaching on the highway. If this cannot be avoided, set up approved traffic signs.

WARNING Fall hazard!

Jumping on or off the machine could cause an injury. Always face the machine, use the handrails and steps, and get on or off slowly.

Maintain a three-point contact to avoid falling: both hands on the handrails and one foot on the step, or one hand on the handrail and both feet on the steps.

Failure to comply could result in death or serious injury.

GHN2P4-005

W0141A

4-30

4

5 - TRANSPORT OPERATIONS

5 - TRANSPORT OPERATIONS###_5_### Shipping transport

Loading the machine onto a transport trailer WARNING Improper operation or service of this machine can result in an accident.

Assign a supervisor to direct worksite operations. Agree on all safety measures, procedures, and suitable hand signals.

Failure to comply could result in death or serious injury.

W0287A

WARNING Transport hazard!

The machine can slip or fall from a ramp or trailer. Make sure the ramp and trailer are not slippery.

Remove all oil, grease, ice, etc. Move the machine on or off the trailer with machine centered on the trailer or ramp.

Failure to comply could result in death or serious injury.

W0152A

Make sure to check the total weight, length, width and height of the machine to be transported. Refer to Chapter 8.

Make sure to use a trailer with a rated capacity and dimensions sufficient to transport the machine. If a rear loading type trailer is used for road transport, make sure that ramps are available to climb onto the trailer bed. Use ramps which have sufficient width, length, thickness and strength. The ramp slope should be 15 ° or less.

Investigate beforehand the conditions of the road to be traveled, weight and size limits, and special local traffic regulations. Obtain any permits required from proper government agencies for machine transportation.

Trailer setup Position the trailer on firm and level ground.

Put blocks to the tires of the trailer to prevent trailer from moving.

If a rear loading type trailer is used for road transport, prepare the loading ramps. If the ramps are included in the trailer frame, lower them to the ground. If the ramps are external to the trailer, match them to the rear edge of the trailer avoiding any bump between trailer bed and external ramps.

SMIL13CEX2717AB

Machine setup Accurately clean the machine undercarriage and tracks to prevent mud or debris from skidding during transport.

Make sure to deactivate the auto idle function and the auto shut-down function. Press the idle mode switch (1) until any idle icon on the monitor turns off.

Press the travel mode selector switch (2) to select the low travel speed. The “Turtle” icon appears on the monitor screen.

D63F2FE7

5-1

2

1

5 - TRANSPORT OPERATIONS

Loading the machine on a rear loading type trailer (with front equipment installed) Select the H work mode.

Align the machine to the trailer, so as the travel motors face the trailer ramps.

NOTICE: In this position, traveling and steering control become opposite to each other.

Get close to the ramps and operate the arm and bucket controls so that the arm stands vertical and the bottom side of the bucket is about 20 cm (7.9 in) above the trailer bed.

SMIL13CEX2720AB

3

SMIL15CEXZZ45AA

4

Slowly climb the trailer ramps keeping the bucket close to the trailer bed. Slowly travel on the trailer bed to reach the resting position, giving particular attention to the attachment so as not to touch the trailer bed.

Slowly turn the upper structure 180 °.

5-2

5 - TRANSPORT OPERATIONS

Loading the machine on a rear loading type trailer (without front equipment installed) WARNING Tip-over hazard!

The counterweight MUST be removed before transporting the machine without an attachment. Consult you dealer.

Failure to comply could result in death or serious injury.

W0260A

WARNING Pressurized system!

Before removing the attachment from the machine, make sure the air pressure and hydraulic oil pressure are at zero.

Failure to comply could result in death or serious injury.

W0284A

If the machine has to be transported without the complete front equipment (boom and arm), the counterweight shall be removed from the base machine. Loading the base machine on the trailer with the counterweight installed affects the stability of the base machine itself, and definitely compromises its climbing ability.

NOTICE: the use of lifting systems is necessary for removal and installation of the machine front attachment and of the counterweight. Refer to your NEW HOLLAND CONSTRUCTION dealer for proper removal and installation procedure.

Select the H work mode.

SMIL13CEX2721AB

5

SMIL15CEXZZ46AA

6

Align the machine to the trailer, so as the travel motors face the trailer ramps.

NOTICE: In this position, traveling and steering control become opposite to each other.

Slowly climb the trailer ramps. Slowly travel on the trailer bed to reach the resting position.

Slowly turn the upper structure 180 °.

5-3

5 - TRANSPORT OPERATIONS

Tie downs for shipping Example 1 1. Set the machine in the position for transport: fully retract the arm and curl the bucket slowly.

2. Place the block (B) on the trailer floor and lower the boom slowly. Adjust the position of the block (B) so that the bucket linkage lays on the block (B).

3. Check the overall height between the ground and the highest point of the machine and check the overall width of the machine. Make sure to be within the size limits defined before transport, in order to confirm documents and permissions already got to comply to the local traffic regulations.

4. Place the gate lock lever in central position. Stop the engine and remove the starter key.

5. Get off the machine. Retract the radio antenna. Fold the rear view mirrors.

6. Lock the cab door and the side panels.

7.

Check the condition of the tie-down points on the trailer.

8.

Secure the machine onto the trailer using chocks (C), chains, wire ropes (A) to prevent the machine from swaying (oscillation) during transport.

9.

Carry out a final check of the tie-down condition.

10. If a rear loading type trailer is used for road transport, lift or remove the loading ramps.

11. Remove blocks from the tires of the trailer.

5-4

03409AAA

(A) Wire rope (B) Block (C) Chock (D) Padding (E) Rubber mat

1

5 - TRANSPORT OPERATIONS

Example 2 1. Set the machine in the position for transport: fully retract the arm and curl the bucket slowly.

2. Place the block (B) on the trailer floor and lower the boom slowly. Adjust the position of the block (B) so that the bucket linkage lays on the block (B).

3. Check the overall height between the ground and the highest point of the machine and check the overall width of the machine. Make sure to be within the size limits of the local traffic regulations.

4. Place the gate lock lever in central position. Stop the engine and remove the starter key.

5. Get off the machine. Retract the radio antenna. Fold the rear view mirrors.

6. Lock the cab door and the side panels.

7. Check the condition of the tie-down points on the trailer.

8.

Secure the machine onto the trailer using chocks (C), chains (D), wire ropes (A) to prevent the machine from swaying (oscillation) during transport. Secure the lower frame to the trailer by passing chains through the chain mounting holes (for transport) in the lower frame and tensioning the chains in an X shape.

Secure both the front and rear of the lower frame in the same manner using chains.

9.

Carry out a final check of the tie-down condition.

967DA1E8

2

(A) Wire rope (B) Block (C) Chock (D) Chain (E) Rubber mat

10. If a rear loading type trailer is used for road transport, lift or remove the loading ramps.

11. Remove blocks from the tires of the trailer.

SMIL13CEX2729BA

5-5

3

5 - TRANSPORT OPERATIONS

Unloading the machine from a transport trailer Rear loading type transport trailer 1. Position the trailer on firm and level ground. Put blocks to the tires of trailer to prevent trailer from moving.

2. Remove chains, wire ropes, chocks, blocks and other devices used to secure the machine during road transport.

3. Prepare the loading ramps. If the ramps are included in the trailer frame, lower them to the ground. If the ramps are external to the trailer, match them to the rear edge of the trailer avoiding any bump between trailer bed and external ramps.

4. Get on the machine and start the engine.

5. Make sure to deactivate the auto idle function and the auto shut-down function. Press the idle mode switch (1) until any idle icon on the monitor turns off. Press the travel mode selector switch (2) to select the low travel speed. The “Turtle” icon appears on the monitor screen.

D63F2FE7

1

6. Select the H work mode and set the gate lock lever in forward position.

7.

If the front equipment is installed, operate the arm and bucket controls so that the arm stands vertical and the bottom of the bucket is about 20 cm (7.9 in) above the trailer bed.

8.

Travel slowly towards the back of the trailer and stop as reaching the ramps. If the front equipment is installed, operate boom and arm softly in order to get the bucket close to the ground ahead of the ramps. Avoid to fully extend the bucket cylinder to prevent damaging it due to accidental impacts with the ground.

9.

Move down on ramps with extreme care while operating boom and arm softly in order to keep the bucket close to the ground and so to grant machine stability.

10. Pass through the ramps completely and stop the machine once it gets on the ground.

5-6

SMIL13CEX2722AB

2

5 - TRANSPORT OPERATIONS

Recovery transport

Towing WARNING Misuse hazard!

Towing is a delicate maneuver that is always carried out at the risk of the user. The manufacturer's warranty does not apply to incidents or accidents that occur during towing. Where possible, carry out the repairs at the site.

Failure to comply could result in death or serious injury.

W0286A

WARNING Hazard to bystanders!

The operator must be the only person on the machine when towing. Make sure that nobody else is on the machine or within its working range.

Failure to comply could result in death or serious injury.

W0259A

NOTICE: Towing must always be done in alignment with the undercarriage.

NOTICE: The machine must be towed very slowly, over a short distance and only if it is really unavoidable.

Towing the machine First, make sure that it can be towed without risk of further damage.

As far as possible try to carry out repairs on spot or consult your NEW HOLLAND CONSTRUCTION Dealer.

If the machine is bogged down for example, it must be towed as follows: 1. Make sure that the shackles, chains and tackle are in perfect condition and strong enough to move the load.

2. Attach the shackles, chains and tackle to the undercarriage taking care to protect any salient angles.

3. Pull the machine without jerking, very slowly and in alignment with the undercarriage.

Z1J1PB-001

5-7

1

5 - TRANSPORT OPERATIONS

Towing a load To tow a load of up to 10 t (22046.23 lb), use one of the towing holes provided for this purpose.

The towing holes are located at the front and rear of the undercarriage.

DZ7HUA-001A

2

Make sure that the slings, chains and accessories are in perfect condition and can bear the load to be moved.

NOTICE: Towing must always be done in alignment with the undercarriage.

IHKO3C-001

5-8

3

6 - MAINTENANCE

6 - MAINTENANCE###_7_### General information

Basic instructions Servicing instructions WARNING Improper operation or service of this machine can result in an accident.

If you do not understand a maintenance procedure, or doubt your ability to perform a maintenance procedure correctly, see your authorized dealer.

Failure to comply could result in death or serious injury.

W0157A

WARNING Improper operation or service of this machine can result in an accident.

Raised equipment or machine movement without an operator can cause serious injury. Always do the following before performing any maintenance: Park the machine on flat, level ground.

Lower the attachment to the ground.

Shut down the engine and remove the ignition key.

Lock the tracks.

Failure to comply could result in death or serious injury.

W0944D

NOTICE: Be sure all the service operations in this section are carried out punctually at the intervals given, in order to ensure optimum performance levels and maximum safety when using the machine.

• Respect the maintenance intervals by checking the hourmeter every day. Before starting maintenance, park the machine on flat, firm ground, away from any obstacles, with the arm retracted and the bucket on the ground. Unless otherwise specified, all maintenance operations must be carried out with the engine stopped, and the key removed from the ignition key. It is preferable to wait for all circuits to cool down before starting work.

• Clean the grease fittings before lubrication. Clean around plugs and filler holes before adding fluid. No dust or dirt must enter the components or the circuits. Wear suitable clothing and remember to use the necessary safety equipment.

• When carrying out service work on the machine, place a "Do not operate" tag on the instrument panel. Never climb down from the operator's compartment leaving the engine running.

• Remove the necessary lower panels during maintenance of certain machine components.

WARNING Moving parts!

Make sure the lower panels are properly closed before driving the machine.

Failure to comply could result in death or serious injury.

W0910A

Any modification to this machine without prior authorization could cause serious injury. Do not make any modifications without authorization. Consult your NEW HOLLAND CONSTRUCTION Dealer.

NOTICE: If you use your machine in particularly harsh conditions (dusty or corrosive atmosphere, etc.), the servicing intervals should be reduced accordingly.

NOTICE: Take particular care to replace all filters regularly. Clean filters mean longer engine running life.

NOTICE: oil and fluid should not be thrown on the ground. They must be stored and removed by a company which is responsible for their recycling or their disposal.

6-1

6 - MAINTENANCE

Hourmeter The hourmeter enables service operations to be scheduled. Its hourly indications are the same as those of a clock when the engine is running.

Servicing intervals are carefully calculated to guarantee safe and efficient machine operation.

Be sure to carry out all the servicing operations properly as defined in this manual.

SMIL16CEX0640AA

1

Daily inspections Every day, before starting work, it is necessary to inspect the machine and service certain of its components.

General remarks • Check signs of leaking oil or water.

• Check that all screws and nuts are correctly tightened.

• Wipe off any dust (engine, operator's compartment etc.).

• Check for any signs of damage.

Engine • Check the oil level and change the oil if necessary.

• Check the coolant level.

• Check the radiator for signs of clogging or deterioration.

• Check the radiator fan belt tension.

• Check the air filter is clean and not restricted.

• Check the components for signs of leaking oil or water.

• Check the condition of all lines.

Upperstructure • Check the fuel tank level.

• Check the hydraulic reservoir level.

• Check that the hydraulic oil is clean.

• Check the components for signs of leaking oil or water.

• Check the condition of all lines.

• Make sure there are no electrical short circuits.

• Check the battery connections are properly tightened.

• Adjust the rear view mirrors.

• Check the cameras.

Undercarriage • Check the pad hardware.

• Check the condition of the tracks.

• Check that the upper and lower track rollers and the idler wheels are not leaking oil.

Attachment 6-2

6 - MAINTENANCE

• Check the cylinders are not leaking oil.

• Check the condition of all lines.

• Check the condition of the bucket teeth.

After starting the engine • Did the engine start correctly? Are the exhaust fumes normal? Any strange noises?

• Check for abnormal noise on the hydraulic components.

• Check the components for signs of leaking oil or water.

• Check the audible alarm devices, working lights and windshield wipers.

• Check that all circuits (travel, swing and tool) are functioning correctly.

NOTICE: if the slightest defect is found, repair it immediately before using the machine or consult your NEW HOLLAND CONSTRUCTION Dealer.

6-3

6 - MAINTENANCE

Fluids and lubricants By using appropriate fluids and lubricants the excavator can operate in ambient temperatures ranging from -15 °C (5 °F) to 40 °C (104 °F). Refer to the list of fluids and lubricants contained in this manual.

NOTICE: When operating the machine in ambient temperatures outside the above mentioned range, consult your NEW HOLLAND CONSTRUCTION Dealer for specific machine provision and for specific fluids and lubricants to be used.

NEW HOLLAND CONSTRUCTION specification

Reference specification

—

—

ASTM D975

NEW HOLLAND AMBRA MASTERGOLD™ HSP ENGINE OIL

MAT3507

Quantity

Fuel tank Engine oil Swing reduction unit Travel reduction unit Engine coolant Hydraulic oil tank (**) Grease

410 L (108 US gal) 23.1 L (6.1 US gal) 5L (1.3 US gal) 5L (1.3 US gal) 30.8 L (8.1 US gal) 147 L (38.8 US gal) —

NEW HOLLAND AMBRA HYPOIDE 90 NEW HOLLAND AMBRA HYPOIDE 90 NEW HOLLAND AMBRA AGRIFLU-OT (*) NEW HOLLAND AMBRA HI-TECH EX LL 46 NEW HOLLAND AMBRA GR-9 MULTI-PURPOSE GREASE

(*) Concentrate antifreeze to be mixed 50/50 with distilled (deionized) water. (**) The total capacity of the hydraulic system is 240 L (63.4 US gal).

6-4

MS 1316 NH 520 A MS 1316 NH 520 A — — MAT3550 Grade A

SAE 15W40 API CI-4 SAE 80W/90 API GL-5 SAE 80W/90 API GL-5 ASTM D 3306 TYPE I ISO 11158 L-HV46 NLGI 2

6 - MAINTENANCE

Engine coolant NEW HOLLAND AMBRA AGRIFLU-OT is the reference genuine product.

NOTICE: Use of different coolant brands is not recommended.

NOTICE: Never add Supplemental Coolant Additives (SCA) when using NEW HOLLAND AMBRA AGRIFLU-OT. NOTICE: Never mix NEW HOLLAND AMBRA AGRIFLU-OT coolant with conventional coolant. Mixing organic based coolant with conventional coolant will reduce the effectiveness of NEW HOLLAND AMBRA AGRIFLU-OT coolant.

NOTICE: If only conventional coolant is available, a complete changeover of the fluid into the cooling system shall be carried out. Refer to the procedure described in the Chapter 6 (Engine coolant replacement).

The engine cooling system shall always be refilled with coolant solution made by mixture of antifreeze and distilled (deionized) water.

NOTICE: Never refill the cooling system with only antifreeze. Never refill the cooling system with only water.

Using NEW HOLLAND AMBRA AGRIFLU-OT, a 50/50 mixture of antifreeze and distilled (deionized) water grants proper performance of the engine cooling system in the above mentioned operating temperature range of the machine.

NOTICE: If operating in extreme winter climate, a coolant solution made by 60/40 antifreeze/distilled (deionized) water mixture shall be used in order to grant proper performance of the engine cooling system.

NOTICE: Never use coolant solution with more than 60 % of antifreeze. This affects the cooling capacity of the mixture.

The antifreeze concentration in the mixture of antifreeze and distilled (deionized) water can be determined with a refractometer designed to measure ethylene glycol content.

If distilled (deionized) water is not available, use water for dilution with the following properties: Property Total Solids Total Hardness Chloride (Cl) Sulfate (SO4) Acidity pH

Maximum limit 340 ppm 340 ppm 340 ppm 100 ppm 5.5 to 9.0

NOTICE: Never use hard water, sea water and softened sea water that has been conditioned with salt. The minerals and salts present in potable water can cause corrosion and deposits resulting in shortened engine life.

6-5

6 - MAINTENANCE

Fuel Use only Low Sulphur Diesel that meets the National Regulations for commercial diesel fuel.

NOTICE: never use Diesel fuel having a sulphur content higher than 350 ppm.

Using other types of fuel may lead to stalled engine output or deterioration in fuel economy.

NOTICE: The warranty shall be invalid if any serious defect is caused by usage of any other fuel. Using fuel other than recommended may cause damage to the fuel injection pump, injector, other fuel supply system or the engine.

NEW HOLLAND CONSTRUCTION may not be responsible to any of such damages.

NOTICE: If operating in severe winter climate, consult the fuel supplier or the CASE CONSTRUCTION dealer for specific diesel fuel to be used.

Conditions applicable to diesel fuel. The diesel fuel used must: • be free from dust particles, even minute ones, • have the proper viscosity, • have a high cetane number, • present great fluidity at low temperatures, • have low sulphur content, • have very little residual carbon.

It is recommended that the following safety information be considered in order to prevent damage to the engine fuel supply system.

• Some fuel suppliers mix old engine oil and diesel fuel.

• Makers of larger engine permit the use of this kind of fuel.

• However, do not use diesel fuel contaminated with engine oil in customer's engines.

• Not only will this fuel damage the engine, it may also have a negative impact on the exhaust gas purification function.

• Before using diesel fuel, confirm with the supplier whether the fuel complies with the above specifications.

NOTICE: Consult the supplier or the NEW HOLLAND CONSTRUCTION Dealer regarding appropriate use of fuel additives.

NOTICE: In order to prevent condensation during cold weather, fill the fuel tank to full after the completing the day's work.

Fuel storage: Long storage can lead to the accumulation of impurities and condensation in the fuel. Engine trouble can often be traced to the presence of water in the fuel. The storage tank must be placed outside and the temperature of the fuel should be kept as low as possible. Drain off water and impurities regularly.

6-6

6 - MAINTENANCE

Environment and ecology Before carrying out any maintenance operation on this machine and before disposing of used fluids or lubricants, always think of the environment. Never throw oil or fluid on the ground and never place it in leaking receptacles.

Consult your local ecological recycling center or your NEW HOLLAND CONSTRUCTION Dealer to obtain information on the correct method of disposing of these lubricants.

The following are recommendations which may be of assistance: • Become acquainted with and ensure that you understand the relative legislation applicable to your country.

• Where no legislation exists, obtain information from suppliers of oils, filters, batteries, fuels, antifreeze, cleaning agents, etc., with regard to their effect on man and nature and how to safely store, use and dispose of these substances.

• Local Environmental Agency will, in many cases, be able to help you as well.

6-7

6 - MAINTENANCE

Engine oil recommended operating temperature range CJ-4 and CI-4 oils

(H)

0W-40 CJ-4 UNITEK to MAT3521

(H)

API CI-4 0W-40 (H)

API CI-4 10W-30

(H)

10W-40 CJ-4 UNITEK to CNH MAT3521

(H)

API CI-4 10W-40 (H)

15W-40 CJ-4 UNITEK to CNH MAT3521

(H)

API CI-4 15W-40 API CI-4 20W-50

-40 °C -40 °F

-30 °C -22 °F

-20 °C -4 °F

-10 °C 14 °F

0 °C 32 °F

10 °C 50 °F

(H) Engine oil pan or coolant block heater recommended in this range

6-8

20 °C 68 °F

30 °C 86 °F

40 °C 104 °F

50 °C 122 °F

6 - MAINTENANCE

Releasing pressure in the hydraulic system NOTICE: before carrying out any work on the hydraulic system, there should be no pressure in any of the circuits.

1. Place the machine on flat, level ground, lower the attachment to the ground and stop the engine.

2. Turn the ignition key to the “On” position.

29ED2C27

1

BDBC08E9

2

F8383E38

3

3. Push the function cancellation lever forward (safety bar in outward position).

4. Operate the control levers from right to left and front to rear a dozen times approximately.

5. Turn the ignition key to the “Off” position (shut down).

6-9

6 - MAINTENANCE

6. Press the button on top of the breather on the hydraulic reservoir to release any residual pressure.

9B3275D9

6-10

4

6 - MAINTENANCE

Grease points Type of grease: NEW HOLLAND AMBRA GR-9 MULTI-PURPOSE GREASE. NOTE: The numbers within brackets mentioned on the right of the description indicate the number of lubrication points.

NOTE: After lubrication, refit the protective and indicating plastic caps to the grease fittings.

Machine

50CB5A58

6-11

1

6 - MAINTENANCE

Every 500 hours Turntable: (2)

5ZISAG-001

2

5ZISAG-002

3

Turntable teeth: (1) See "Greasing the turntable teeth".

6-12

6 - MAINTENANCE

Attachment Monobloc boom/arm

ADA3B2BE

4

NOTICE: if the following linkage points are not equipped with original parts, these points must be lubricated every 50 hours.

Every 1000 hours Boom bottom pin: (2) Boom cylinder top pin: (2) Arm cylinder bottom pin: (1)

8U6DVD-001

6-13

5

6 - MAINTENANCE

Every 1000 hours Boom cylinder bottom pin: (2)

8U6DVD-002

6

Boom/arm linkage: (2)

39861E1F

7

52DB0087

8

Arm cylinder top pin: (1)

6-14

6 - MAINTENANCE

Arm/backhoe bucket

74694DC6

9

NOTICE: if the following linkage points are not equipped with original parts, these points must be lubricated every 10 hours.

Every 250 hours Bucket linkages: (2) NOTICE: if an accessory other than the bucket is installed, (hydraulic hammer, etc.) these points must be lubricated every 10 hours.

6AJ2D6-001B

6-15

10

6 - MAINTENANCE

NOTICE: if these linkage points are not equipped with original parts, these points must be greased every 50 hours.

Every 1000 hours Yoke/connecting rod linkages: (4) NOTICE: if an accessory other than the bucket is installed, (hydraulic hammer, etc.) these points must be lubricated every 10 hours.

8U6DVD-016B

11

Bucket cylinder bottom pin: (1)

8U6DVD-017

6-16

12

6 - MAINTENANCE

Greasing the turntable teeth Type of grease: NEW HOLLAND AMBRA GR-9 MULTIPURPOSE GREASE

Every 500 hours Remove the inspection cover (1) and visually check the condition of the gear surface and for any damage.

If the gear surface is not well greased, add grease.

If the grease is white due to moisture content, etc. replace it with new grease.

5ZISAG-003

13

5ZISAG-008

14

If the presence of water is detected, remove the plug (2) and drain off the water.

1. Remove the protective panel from the lower central area.

2. Remove plug (2).

3. Discharge the water or contaminated grease.

4. Install plug (2).

5. Insert new grease through the port and install the inspection cover (1).

6-17

6 - MAINTENANCE

Greasing the Swing Reduction Gear Type of grease: NEW HOLLAND AMBRA GR-9 MULTIPURPOSE GREASE

Every 2000 hours 1. Remove the air bleed plug (1) and add the grease through the grease injection point (2).

2. The appropriate injection amount is when some grease overflows the air bleed plug (1).

15E8A477

6-18

15

6 - MAINTENANCE

Levels NOTE: The numbers within brackets mentioned on the right of the description indicate the number of levels.

Every 10 hours Engine oil: (1) Refer to page 6-21.

7FC89047

1

Coolant solution expansion reservoir: (1) Refer to page 6-24.

UJHECF-002

2

UJHECF-003

3

Hydraulic reservoir: (1) Refer to page 6-36.

6-19

6 - MAINTENANCE

Every 250 hours Batteries: (2) Refer to page 6-75.

EAEF6DE4

4

Travel reduction gears: (2) 1. Drain 2. Level 3. Fill Refer to page 6-51.

LOX1WD-001

5

Swing reduction gear: (1) Refer to page 6-49.

81B69CA1A

6-20

6

6 - MAINTENANCE

Engine Engine oil level check: Every 10 hours or every day Oil replacement: Every 500 hours Oil filter replacement: Every 500 hours Oil capacity: 23.1 l (6.1 US gal) Type of oil: NEW HOLLAND AMBRA MASTERGOLD™ HSP ENGINE OIL

Level 1. Park the machine on flat, horizontal ground. Stop the engine, remove the ignition key.

2. When the engine has been stopped for ten to twenty minutes, raise and lock the engine hood, remove the dipstick, wipe it with a clean cloth and insert it back in the guide tube as far as it will go. Then take it out again.

7FC89047

1

3. If the level is situated between the marks (A) and (B) on the dipstick, the level is correct.

2

MMYFQD-002

4. If the oil level is at mark (A) (min) or below, remove the filling plug and add oil up to mark (B) (max) of the dipstick, install the plug.

NOTICE: the level should not be higher than the mark (B) (maximum on the dipstick).

F6289A90

6-21

3

6 - MAINTENANCE

Draining, changing the oil filter and filling NOTE: Change the oil while the engine is still warm. The oil will flow more easily.

Use the extension drain hose from the front boot.

1. Place the machine on flat, level ground. Stop the engine, remove the ignition key then open the hatch under the engine.

2. Raise and lock the engine hood, remove the filling plug.

F6289A90

4

3. Remove the protective cap from the engine housing drain valve.

4. Screw the end of the extension drain hose onto the engine check valve, place the other end in a container of suitable capacity and allow the oil to flow out.

5. Remove the extension drain hose and install the protective cap on the housing check valve. Place the extension drain hose in the front storage compartment.

VD9EED-002

5

6. Clean the area around the filter located in the rear right-hand compartment, remove it using a filter wrench.

28C8266F

6-22

6

6 - MAINTENANCE

7. Coat the seal of the new filter with a fine film of oil.

8. Install the new filter. Turn the filter until the seal comes into contact with the filter head then tighten an extra half turn by hand.

NOTICE: do not use a filter wrench to tighten the filter.

Excessive tightening can damage the filter and their seals.

VD9EED-004

9.

7

Fill the engine with new engine oil. Install the filling plug and protective cover.

10. Run the engine for a few minutes and check that there are no leaks. Check the level again and top up if necessary.

NOTICE: Always wait fifteen minutes to allow the oil to return to the sump before checking the oil level.

F6289A90

6-23

8

6 - MAINTENANCE

Cooling system CAUTION Burn hazard!

Take care if removing the filler cap while the system is hot. Before removing the cap: completely cover the cap using a thick cloth, and slowly open the filler cap to allow the pressure to escape. Do not add cold water to a hot coolant reservoir.

Failure to comply could result in minor or moderate injury.

C0031A

WARNING Hazardous chemicals!

Coolant can be toxic. Avoid contact with skin, eyes, and clothing. Antidotes: EXTERNAL - Rinse thoroughly with water. Remove soiled clothing.

INTERNAL - Rinse the mouth with water. DO NOT induce vomiting. Seek immediate medical attention.

EYES - Flush with water. Seek immediate medical attention.

Failure to comply could result in death or serious injury.

W0282A

Service specifications Expansion reservoir level check: Every 10 hours or every day Checking the tightening of clamps, of radiator hoses: Every 250 hours or every 6 months Draining the system (long duration): Every 4000 hours or every 2 years Draining the system (with anti-freeze) (spring and autumn): Twice a year System capacity: 30.8 l (8.1 US gal) Type of coolant: NEW HOLLAND AMBRA AGRIFLU-OT NOTICE: Check and service the cooling system according to the instructions given in this manual.

Coolant solution Put only ethylene-glycol coolant solution in the cooling system. Use good quality ethylene-glycol that has a high boiling point, with no additives to prevent leakage. Do not use non-approved anti-rust additives. Anti-rust additives and ethylene-glycol can mix and work against each other, thereby reducing anti-corrosion protection, forming deposits in the cooling system and causing damage to the cooling system and radiator.

Consult your NEW HOLLAND CONSTRUCTION Dealer who will supply you with the suitable coolant.

Level The level of coolant solution should be checked when the engine is cold.

On flat, level ground, before using the machine (while the engine is still cold), the level in the expansion reservoir should be between the “Full” (1) and “Low” (2) marks. If not, see "Filling".

MMYFQD-004

6-24

1

6 - MAINTENANCE

Draining CAUTION Burn hazard!

Hot coolant can spray out if you remove the filler cap while the system is hot. After the system has cooled, turn the filler cap to the first notch and wait for all pressure to release before proceeding.

Failure to comply could result in minor or moderate injury.

C0043A

1. Remove the radiator plug.

K272V1-002

2

K272V1-003

3

K272V1-008

4

2. Open the radiator drain valve located in the rear lefthand compartment.

3. Open the drain plug located on the engine block.

NOTE: Have a receptacle of a suitable capacity ready.

6-25

6 - MAINTENANCE

Rinsing 1. Close the drain valve once the radiator is completely empty. Close the plug on the engine block.

2. Fill the system with clean water. Install the radiator cap.

3. Start the engine. Run the engine at a speed slightly higher than idle speed for ten minutes to bring the engine temperature up to about 80 °C (176.0 °F) .

4. Stop the engine and remove the ignition key.

5. Drain the system once more.

6. Repeat Steps 1 to 5 until the water drained is clear.

Filling 1. Fill with coolant solution via the radiator until overflowing and install the radiator cap.

2. Squeeze the upper radiator hose with your hand a few times to bleed the air in the hose and refill with coolant until it reaches the filling hole.

3. Repeat this until the coolant level does not drop any longer.

4. When filling is done, install the radiator cap.

K272V1-002

5

DC2MPI-002

6

5. Fill the expansion reservoir to the “Full” mark and install the cap.

NOTICE: use the correct coolant solution.

6-26

6 - MAINTENANCE

6. Loosen the air bleeder plug (1) of the cooler to remove the air inside the cooler.

7. Tighten the air bleeder (1) when the coolant overflows from the air bleeder plug (1).

Air bleeder plug (1) tightening torque 22 N·m (16.226 lb ft).

8. Run the engine at idle speed for about five minutes.

Add coolant solution if the level in the expansion reservoir drops.

NOTICE: do not fill the expansion reservoir above the “Full” mark.

46B31C96

6-27

7

6 - MAINTENANCE

Fuel system Service specifications Fuel tank bleeding: Every 10 hours or every day Filter bleeding: When the float reaches the level (A) Pre-filter bleeding: When the float reaches the level (A) Replace the pre-filter element: Every 250 hours Replace the filter element: Every 500 hours Fuel supply pump filter cleaning: Periodically Fuel tank capacity: 410 l (108.3 US gal) NOTICE: take all necessary precautions during the following operations; no foreign matter must enter the fuel system.

NOTICE: when you deal with fuel, please do not bring fire close. After exchange of the filter and scupper of fuel should wipe off the fuel which fell.

NOTICE: do not work in any environment in which anything other than fuel will get into fuel lines. (Sites with strong wind, blowing dust, etc.). Wash hands before operations. Do not use gloves. Do not open the packaging for the filter kit until you start the installation work. Do not reuse any fuel remaining within the cover. For persistent dirt within the cover, wipe it off with a clean rag, then clean with clean diesel fuel. Do not use parts cleaner because it could affect the case cover. Do not touch the inside of the element. Completely wipe off any spilt fuel after changing a filter element or bleeding the system.

Draining the fuel tank 1. Place a receptacle of a suitable capacity under the drain plug.

2. Open the drain valve located at the bottom of the tank and drain the accumulated sediment and water.

3. After draining, close the drain valve.

YOS5FC-001

6-28

1

6 - MAINTENANCE

Pre-filter bleeding When the float reaches the level line (A) and when the message "FUEL FILTER" is displayed on the monitor: 1. Place a receptacle of a suitable capacity under the pre-filter.

2. Loosen the drain plug (1) and the bleed screw (2) then drain the water and sediment.

3. When the float (3) settles on the bottom, tighten the drain plug (1) and the bleed screw (2).

Tightening torque: 8 - 12 N·m (5.9 - 8.9 lb ft) NOTICE: overtightening can damage the seal.

4. Check for any signs of leak.

NOTICE: In cold weather, the water can freeze on the top part of the bowl. Bleed after the ice has melted.

EBBCE1FF

2

BAABF7F2

3

Replacing the pre-filter element NOTICE: if a fuel filter other than a genuine NEW HOLLAND CONSTRUCTION filter is used, the guarantee will not be applied to a fault caused by the use of a wrong filter.

Two pre-filters are installed. Replace one pre-filter at a time.

1. Place a receptacle of a suitable capacity under the pre-filter.

2. Close the valves on the supply line.

SMIL16CEX0355AA

6-29

4

6 - MAINTENANCE

3. Loosen the drain plug (1) and the bleed screw (2) then let the pre-filter drain.

CD42D6F1

5

4. Clean around the pre-filter body then remove it using the wrench provided with the machine.

5. Install the new filter element. Replace the filter body seal, then install the body, turning it until it is in contact with the pre-filter head.

NOTICE: do not fill the filter body with fuel before installing.

6. Tighten the body using the wrench, the tightening torque must be from 28 - 32 N·m (20.7 - 23.6 lb ft).

NOTE: Bind tight within regulation torque.

QOIPZB-010

6

7. Replace the drain plug (1) seal then install the drain plug (1); the tightening torque must be between 8 12 N·m (5.9 - 8.9 lb ft) NOTICE: overtightening can damage the seal.

NOTICE: never re-use the seals of the filter body or the drain plug (1); they must always be replaced with new seals.

NOTE: Bind tight within regulation torque.

CD42D6F1

6-30

7

6 - MAINTENANCE

With the same procedure, replace the other prefilter element.

8. Open the valve on the supply line.

9. Bleed the system. See "Fuel system air bleed".

BAABF7F2

8

SMIL16CEX0355AA

9

Bleed the filter Proceed in the same manner as for the pre-filter. See "Pre-filter bleeding".

377EB29E

Replacing the filter element NOTICE: if a fuel filter other than a genuine NEW HOLLAND CONSTRUCTION filter is used, the guarantee will

10

not be applied to a fault caused by the use of a wrong filter.

6-31

6 - MAINTENANCE

Proceed in the same manner as for the pre-filter. See "Replacing the pre-filter element".

12276E3B

11

0D9EB2F4

12

49221445

13

Fuel system air bleed NOTICE: When the fuel tank has been emptied after replacement and/or draining water of the pre-fuel filter or the fuel filter (3) has been carried out, be sure to bleed air as this may prevent fuel flow because of air entering inside.

(1) Priming pump (2) Air bleed plug (3) Fuel filter

(4) Air bleed plug (5) Air bleed plug

6-32

6 - MAINTENANCE

1. Place a receiving container under the end of fuel drain hose.

2. Set each screw of (A) and (B) as follows.

Screw (A) (fuel tank): Open Screw (B) (engine): Close

SMIL16CEX0356AA

3. Loosen the air bleeding plug (2) on fuel filter. Do not loosen the air bleeding plug (4), (5) of the pre fuel filter.

4. Insert the key into the ignition switch and turn the key to the “On” position. Electromagnet feed pump operates by this.

NOTICE: do not turn “On” the ignition key for more than 5 minutes unless bleeding air has been completed. Otherwise, this may cause breakdown of the electromagnetic fuel pump.

5. Turn the handle of the feed pump (1) to the left and it will spring up due to the spring inside the handle.

6. By moving the priming pump (1) , the fuel that contains bubbles can be drained from the air bleed plug.

Move the priming pump until no air comes out from the air bleed plug (2) .

7. Tighten the air bleed plug (2).

Air bleed plug tightening torque: 9.8 N·m (7.228 lb ft) NOTICE: do not tighten the air bleed plug more than its specified torque. Doing so might damage the O-rings.

8. Move the priming pump until the fuel filter is filled with fuel (10 times or more).

9. Wait about 1 minute and loosen the air bleed plug, then bleed the air from the fuel filter.

10. Repeat steps 6. through 9. until no air comes out from the air bleed plug. (at least 3 times) 11. Loosen the air bleed plug (4) of the each fuel prefilter.

Move the priming pump (1) until no air comes out from the air bleed plug (4) .

12. Tighten the air bleed plug (4).

Air bleed plug tightening torque: 9.8 N·m (7.228 lb ft) 13. Loosen the air bleed plug (5) of the each fuel prefilter.

Move the priming pump (1) until no air comes out from the air bleed plug (5) .

14. Tighten the air bleed plug (5).

Air bleed plug tightening torque: 9.8 N·m (7.228 lb ft)

6-33

14

6 - MAINTENANCE

15. Move until the priming pump (1) becomes harder to move.

16. Return the priming pump (1) back to its original position.

17. Place the screws A and B in the following positions.

Screw A (fuel tank): Open Screw B (engine): Open 18. Completely wipe off any spilled fuel around the air bleed plugs (2) (4) (5) , start the engine, and check for any fuel leaks.

Start the engine without controlling the engine speed at the machine side.

At this time, if the engine does not start, repeat from step 6.

19. After the engine is started, keep the speed at idle for 5 seconds.

20. Slowly increase the engine speed until it reaches the maximum engine speed.

Repeat this operation a few times.

Cleaning the fuel supply pump filter 1. Located near the fuel pre-filter, place a receptacle of suitable capacity under the supply pump.

16B28148

15

2. Close the valves on the supply line then remove the supply pump.

SMIL16CEX0357AA

6-34

16

6 - MAINTENANCE

3. Open the pump body and extract the filter (3) and the seals (2) and (4).

WARNING Flying debris!

Compressed air can propel dirt, rust, etc. into the air. Wear eye and face protection when using compressed air.

Failure to comply could result in death or serious injury.

W0307A

4. Clean the filter with compressed air. Check the filter and replace it if necessary. Replace the seals with new seals.

5. Carefully clean the body (5) and the cover (1). No dirt must remain in the supply pump.

6. Re-assemble, taking care to install the seals in the correct order then re-install the pump.

7. Open the valve on the supply line.

8. Bleed the system. See "Fuel system air bleed".

6-35

EQFU5N-003A

17

6 - MAINTENANCE

Hydraulic circuit WARNING Burn hazard!

Before performing any service on the hydraulic system, you must allow it to cool. Hydraulic fluid temperature should not exceed 40 °C (104 °F).

Failure to comply could result in death or serious injury.

W0241A

WARNING Escaping fluid!

Hydraulic fluid or diesel fuel leaking under pressure can penetrate the skin and cause infection or other injury. To prevent personal injury: Relieve all pressure before disconnecting fluid lines or performing work on the hydraulic system. Before applying pressure, make sure all connections are tight and all components are in good condition. Never use your hand to check for suspected leaks under pressure. Use a piece of cardboard or wood for this purpose. If injured by leaking fluid, see your doctor immediately.

Failure to comply could result in death or serious injury.

W0178A

WARNING Pressurized system!

Never attempt to drain fluids or remove filters when the engine is running. Turn off the engine and relieve all pressure from pressurized systems before servicing the machine.

Failure to comply could result in death or serious injury.

W0905A

Service specifications Check the hydraulic reservoir fluid level: Every 10 hours or each day Check the lines: Every 50 hours Draining water and sediment from the hydraulic reservoir: Every 250 hours Check the condition of the hydraulic fluid: Every 1000 hours Replace the reservoir breather filter element: Every 1000 hours Clean the inlet screen: Every 2000 hours Replace the return filter: Every 2000 hours (after the first 250 hours during the run-in period) Replace the pilot filter: Every 2000 hours (after the first 250 hours during the run-in period) Check the main pump outlet hoses: Every 2 years or every 4000 hours (whichever comes first) Check the boom, arm and bucket cylinder hoses: Every 2 years or every 4000 hours (whichever comes first) Replace the suction filter: Every 5000 hours Replace the hydraulic fluid: Every 5000 hours Reservoir capacity: 147 l (38.8 US gal) Total system capacity: 240 l (63.4 US gal) Type of oil: NEW HOLLAND AMBRA HI-TECH EX LL 46 NOTICE: if the machine is new or if a major component has been overhauled or changed in the hydraulic system, change the pilot filter and return filter after 50 hours of operation. After that, change these filters at the stipulated interval.

NOTICE: every 1000 operating hours, it is necessary to have the hydraulic fluid analyzed. Consult your NEW HOLLAND CONSTRUCTION Dealer.

NOTICE: after changing the hydraulic fluid, it is necessary to bleed all air from the hydraulic components. See "Bleeding air from the hydraulic components".

NOTICE: If metal particles are found in the old filters, consult your NEW HOLLAND CONSTRUCTION Dealer.

6-36

6 - MAINTENANCE

Level in the reservoir 1. Place the machine on flat, level ground and place the attachment in the position shown. Stop the engine and remove the ignition key.

CD50F03F

1

2. The oil should be in the middle of the indicator. Add more oil if necessary. See "Filling the reservoir".

INHU39-002

2

Filling the reservoir 1. Release all pressure in the hydraulic reservoir. Refer to page 6-9.

2. Clean the cover plate and the area around the plate.

Remove the cover plate and add hydraulic fluid to the reservoir as required.

3. Replace the cover plate seal if required and install the cover plate.

NOTICE: Make sure that no contaminant (water, sand etc.) enters the reservoir during filling.

134A351A

6-37

3

6 - MAINTENANCE

Draining the reservoir sediment 1. Release all pressure in the hydraulic reservoir. Refer to page 6-9.

2. Place a receptacle of a suitable capacity under the drain plug.

3. Open the drain valve on the bottom of the reservoir and drain the sediment and water accumulated at the bottom of the reservoir.

4. After draining, close the drain valve.

5. Add hydraulic oil if necessary. See "Filling the reservoir".

7DWMPL-003

4

Replacing the pilot filter 1. Release all pressure in the hydraulic system. Refer to page 6-9.

2. Unscrew and remove the filter using a wrench.

3. Coat the seal of the new filter with a fine film of clean oil.

4. Install the new filter. Turn the filter until the seal comes into contact with the filter head then tighten by an extra third of a turn by hand.

OFEZLI-001

6-38

5

6 - MAINTENANCE

Cleaning and replacement of the suction filter 1. Release all pressure in the hydraulic reservoir. Refer to page 6-9.

2. Clean the top of the hydraulic reservoir and clean the suction filter cover.

134A351A

6

C6A9992E

7

3. Remove the cover (1) and the O-ring (2) on the top of the suction filter rod assembly.

4. Remove the filter (3) and clean with solvent. Dry it completely and check it for any damage. If there is any damage on the surface, replace it with a new one.

5. Install a new O-ring (2) and install the filter (3) and rod assembly.

6. Install the cover (1).

7. Check the level of the hydraulic fluid and add more if necessary. See "Filling the reservoir".

NOTICE: install a new inlet screen every 5000 hours of operation or when the hydraulic fluid is changed.

6-39

6 - MAINTENANCE

Replacing the return filter 1. Release all pressure in the hydraulic reservoir. Refer to page 6-9.

2. Clean the top of the hydraulic reservoir and clean the return filter cover.

960A6F58

8

F4887800

9

3. Remove the cover (1) and O-ring (2).

4. Take out the spring (3), valve (4) and filter (5).

5. Install a new filter (5). Clean the spring (3) and valve (4) and install them.

6. Check O-ring (2) and change it if worn or damaged.

7. Install the cover (1).

8. Check the level of the hydraulic fluid and add more if necessary. See "Filling the reservoir".

6-40

6 - MAINTENANCE

Replacing the reservoir breather filter element

18D90D7D

10

19IXC6-002

11

1. Press the button (1) to release all pressure in the hydraulic reservoir.

2. Remove the nut (2) and the cover (3) from the breather.

3. Remove and discard the used filter element (4).

4. Install a new element (4), making sure the seal (5) is facing upwards.

5. Install the cover (3) as well as the nut (2).

6-41

6 - MAINTENANCE

Replacing the hydraulic fluid 1. Release all pressure in the hydraulic reservoir. Refer to page 6-9.

2. Remove the reservoir cover plate.

3. Using a pump, remove the fluid from the hydraulic reservoir. Have a container with a suitable capacity ready.

1CC3C737

12

4. Place a receptacle of a suitable capacity under the reservoir drain valve, open the reservoir drain valve and allow the remainder of the fluid to flow out.

5. Change the suction filter and the return filter. See "Cleaning and replacement of the suction filter" and "Replacing the return filter".

6. Close the reservoir drain valve.

7. Fill the reservoir with new hydraulic fluid. See "Filling the reservoir".

8. Replace the cover plate seal if required and install the cover plate on the reservoir.

NOTICE: before you start the engine, it is very important that you bleed air from all the hydraulic components. See "Bleeding air from the hydraulic components".

9.

Start and run the engine with no load for approximately five minutes.

10. Move each control several times to remove any air in the system.

11. Swing the upperstructure evenly left to right two complete turns or more.

12. Place the machine in position and then stop the engine.

13. Check the oil level in the hydraulic reservoir and add oil as required and check that there are no air bubbles in the hydraulic reservoir.

6-42

7DWMPL-004

13

6 - MAINTENANCE

Bleeding air from the hydraulic components NOTE: After bleeding air from the components, stop the engine for five minutes and check there are no bubbles at the surface of the hydraulic fluid in the reservoir.

Hydraulic pump • Using a solvent, clean the periphery of the air bleed plug. Loosen the air bleed plug, remove the plug if the fluid does not flow.

• Fill the pump with new clean hydraulic fluid. Install and tighten the air bleed plug.

• Start the engine and run it at low idle speed. Loosen the air bleed plug on the pump. Tighten the plug when air free fluid comes out of the bleed plug hole. Clean the area completely.

D7380F5E

14

FA215A6B

15

634625F4

16

Swing motor • Start the engine and run it at low idle speed. Loosen the drain port and make sure hydraulic fluid runs out. If necessary, stop the engine and add oil via the orifice. Install the plug without tightening, then start the engine and run it at low idle speed, leaving it to run until oil begins to run from the orifice. Tighten the air bleed plug completely. Swing the upperstructure at least twice completely to the right and twice completely to the left.

• After complete bleeding, stop the engine for five minutes then check that there are no air bubbles in the hydraulic reservoir.

Attachment cylinders • Start the engine and run it at low idle speed. Extend and retract the attachment cylinder rods four or five times without bringing them to end of stroke. Then repeat the operation three or four times, this time bringing the cylinder rods to end of stroke.

6-43

6 - MAINTENANCE

Replacing the hydraulic filters and fluid when a hydraulic breaker is used (optional) When using the hydraulic breaker, hydraulic fluid deteriorates more quickly than during ordinary digging. Check the hydraulic fluid level more frequently. In addition, when changing the filters, also check the condition of the hydraulic fluid.

Using the following graph as a reference, determine the intervals for changing the hydraulic fluid and filters, depending on the frequency of use of the hydraulic breaker.

Percentage of use Interval in hours Hydraulic fluid Return circuit filter Inlet filter Pilot filter Hydraulic fluid condition

10

100% 100

(1) (3) (2) (3) 200H

600

10

(3)

(1)

(3)

40% 20% 300 1500 10 600 300 Service points (3) (1) (3) (3) (3) (2) (3) (2) (3) (3) (3) 300H 600H

10

10% 800 4000

(1)

(3) (3) (2) (3) 800H

(3)

(1) Check the level (2) Clean or replace (3) Replace

Checking the hydraulic system piping Make sure there are no leaks from the hydraulic system hoses, pipes, plugs, connections and fittings and check that all nuts and screws are correctly tightened. In the event of problems, repair, change or tighten the component(s) concerned.

6-44

6 - MAINTENANCE

Air filter Inspection Be sure to carry out regular checks on the air filter, intake manifold, seals and hoses. At the same time, check the intake manifold screws and hose clamps for tightness.

The hoses should be changed before they are worn.

Service specifications Inspect and clean the primary element: Every 250 hours or when the "Air filter" message is displayed on the message display screen Replace the primary element: Every 1000 hours or after cleaning 6 times Replace the secondary element: Every 1000 hours NOTICE: the primary element can be cleaned. The secondary element cannot be cleaned and must be changed.

NOTICE: Observe the air filter service intervals shown above. Clean filters mean longer engine life.

Removing the elements 1. Release the fasteners and remove the cover.

2B78FA68

1

66492C43

2

2. Remove the primary element.

6-45

6 - MAINTENANCE

3. Remove the secondary element if it needs changing.

NOTICE: the secondary element must be changed, not cleaned.

C162FE11

3

Cleaning the primary element WARNING Flying debris!

Compressed air can propel dirt, rust, etc. into the air. Wear eye and face protection when using compressed air.

Failure to comply could result in death or serious injury.

W0307A

If the primary element is dry: Blow compressed air from the inside towards the outside at very low pressure. The compressed air nozzle should be held at least 3 cm from the inside wall of the element.

Cleaning is completed once no more dust comes out of the primary element.

NOTICE: compressed air pressure should not exceed 7 bar.

NOTICE: do not use compressed air if there is oil or soot in the element.

CT02D120TBP1

4

If the cartridge is greasy: Clean it in water with a suitable detergent (consult your NEW HOLLAND CONSTRUCTION Dealer). Instructions for using the detergent are printed on the packaging.

NOTE: Allow the element to dry completely before installing it. It is advisable to keep a spare, clean element ready for installation on the air filter while the cleaned element is drying.

OESMY5-002

6-46

5

6 - MAINTENANCE

Inspecting the element Check the element for damage by placing an inspection lamp inside the element.

NOTICE: change the element if light can be seen through a hole, however small.

6

PDE0378ATBP1

Installing the elements 1. Install the secondary element.

C162FE11

7

66492C43

8

607EDCC8

9

2. Install the primary element.

3. Install the cover (with the word “TOP” at the top) and close the fasteners.

4. Check that the dust ejector (1) under the filter is working correctly.

NOTICE: if exhaust smoke is abnormal after cleaning, the air filter primary element must be changed.

6-47

6 - MAINTENANCE

Pre-cleaner (if equipped) If dust within the case accumulates up to the dust level, dispose of dust within the case.

71EF6874

6-48

10

6 - MAINTENANCE

Swing reduction gear WARNING Hot surface possible!

Wait for all components to cool before performing any operation.

Failure to comply could result in death or serious injury.

W0251A

Service specifications Oil level check: Every 250 hours Oil drain: Every 1000 hours (after the first 250 hours during the run-in period) Oil capacity: 5.0 l (1.3 US gal) Type of oil: NEW HOLLAND AMBRA HYPOIDE 90

Level check 1. Park the machine on flat, horizontal ground. Stop the engine and remove the ignition key.

2. Remove the dipstick (2). The oil should come up to the hatched area. If necessary, add more oil through the filler hole (1).

3. Install the dipstick.

7E88751A

1

7E88751A

2

Draining and refilling 1. Park the machine on flat, horizontal ground. Stop the engine and remove the ignition key.

2. Remove the dipstick (2) and the filler plug (1).

6-49

6 - MAINTENANCE

3. Place a receptacle of a suitable capacity under the upperstructure frame, remove the oil drain plug (3) and allow the oil to flow out.

NOTE: The oil takes a relatively long time to drain.

NOTICE: check the condition of the drained oil. If it contains metal filings or foreign matter, consult your NEW HOLLAND CONSTRUCTION Dealer.

4. Install the drain plug (3).

2A76B812

3

7E88751A

4

5. Add oil through the filler hole (1) until the level is correct.

6. Install the dipstick (2) and the filler plug (1).

7. Wait ten minutes and then use the dipstick (2) to check the oil level again. If necessary, add more oil through the filler hole (1).

6-50

6 - MAINTENANCE

Travel reduction gears Service specifications Oil level check: Every 250 hours Oil drain: Every 1000 hours (after the first 250 hours during the run-in period) Oil capacity (per reduction gear): 5 l (1.3 US gal) Type of oil: NEW HOLLAND AMBRA HYPOIDE 90

Level 1. Park the machine on flat, horizontal ground.

2. Move the machine so that plug (1) is in the lowest possible position.

3. Stop the engine and remove the ignition key.

4. Slowly loosen the plug (3) to release any residual pressure.

5. Remove the plug (2) and check the oil level. The level must come up to the bottom edge of the port (2). If required, remove the plug (3) and top up through this port until oil comes up to the bottom edge of the port (2).

6. If necessary, replace the seals of plugs (2) and (3) then replace the plugs.

LOX1WD-001

1

LOX1WD-001

2

7. Repeat Steps 2 to 6 for the other travel reduction gear.

8. Travel slowly with the machine and make sure there are no leaks.

Draining and refilling 1. Park the machine on flat, horizontal ground.

2.

Move the machine so that plug (1) is in the lowest possible position.

3.

Shut down the engine and remove the ignition key.

4.

Place a receptacle of suitable capacity under the travel reduction gear.

5.

Slowly loosen the plug (3) to release any residual pressure then remove the three plugs.

6.

Allow the oil to drain.

NOTICE: check the condition of the drained oil. If it contains metal filings or foreign matter, consult your NEW HOLLAND CONSTRUCTION Dealer.

7.

If required, replace the plug seals.

8.

Install the plug (1), fill with oil through the port (3) until oil comes up to the bottom edge of port (2), then install the plugs (2) and (3).

9.

Repeat Steps 2 to 8 for the other travel reduction gear.

10. Travel slowly with the machine and make sure there are no leaks.

6-51

6 - MAINTENANCE

Tracks Service specifications Clean: Periodically and when the machine has been working in mud Check tension: Periodically Check steel pad screw torques: Every 250 hours (after the first 50 hours during the run-in period) NOTICE: if the tracks are too tight, they wear quickly. If tracks are not tight enough, they wear quickly and the links can catch on the sprocket wheel or slide off the idler wheel or the sprocket wheel. Clean the tracks after work.

Cleaning When the machine has been working in mud, a reduction in temperature can cause the mud to solidify.

1. Place the upperstructure at right angles to the undercarriage. Use the attachment to press on the ground and lower the boom until the track is raised off the ground. Then place a block beneath the undercarriage to relieve the attachment.

WARNING Tip-over hazard!

Only raise the track as little as necessary.

Failure to comply could result in death or serious injury.

W0276A

SOEUXT-009

1

2. Turn the engine throttle to maximum speed position.

E0DDB3F4

2

585C44C3

3

3. Use the travel speed selector (3) to select high speed.

6-52

6 - MAINTENANCE

4. Operate the travel control lever for the raised track forward and then in reverse, to remove the mud.

5. With the track raised, check the track tension.

6. Repeat Steps 1 to 5 for the other track.

SOEUXT-010

4

1IUTUH-001

5

1V7EYE-002

6

Checking the tension 1. If the track is not yet raised, put the machine into the required position by proceeding in the same manner as for cleaning. See "Cleaning".

2. Use the travel control lever to operate the raised track in reverse for a few moments.

3. Stop the engine and remove the ignition key.

4. Measure the sag of the track at the center between the base of the undercarriage and the pad.

The value must be between: 300 mm (11.8 in) and 330 mm (13.0 in).

5. Adjust the tension if necessary and then lower the raised track to the ground.

6. Repeat Steps 1 to 5 for the other track.

Adjusting the tension NOTE: This operation is to be carried out after the tension has been checked.

To increase tension 1. Clean the grease fitting adaptor and the grease fitting.

2. Connect the grease pump. Inject grease to obtain the right amount of track tension.

The value must be between: 300 mm (11.8 in) and 330 mm (13.0 in).

3. Remove the grease pump and clean the grease fitting.

4. Repeat Steps 1 to 3 for the other track.

6-53

6 - MAINTENANCE

To reduce tension WARNING Pressurized fluid can penetrate the skin and cause severe injuries.

The grease in the cylinder is under high pressure. Never loosen the grease fitting adaptor completely in order to speed up the flow of grease.

Failure to comply could result in death or serious injury.

W0261A

1. Loosen the grease fitting adaptor by about three turns to allow grease to flow out of the cylinder.

2. As soon as the right track tension is obtained, tighten the adaptor.

The value must be between: 300 mm (11.8 in) and 330 mm (13.0 in).

3. Clean the grease adaptor and fitting and then lower the raised track to the ground.

4. Repeat Steps 1 to 3 for the other track.

NOTICE: If the grease fitting adaptor is damaged, grease may leak out. Check the condition of the grease fitting adaptor regularly and replace it if necessary.

WRQF7U-001

7

UEBLNV-001

8

UEBLNV-002

9

Tightening torque of the track pad screws NOTICE: regularly check the tightening of the screws. Do not use the machine with the track pad screws loose, the screws may come off and damage the track.

The tightening torque of the screws must be: 250 - 350 N·m (184 - 258.1 lb ft) + 120 ° (133.3 Grade)

NOTE: Follow the prescribed order.

6-54

6 - MAINTENANCE

Track rollers and idler wheels Service specifications Check: Every 250 hours The upper and lower rollers and idler wheels use a permanent floating seal type sealing mechanism. The service life normally lasts until overhaul, but check visually from time to time before work for oil leakage. If oil leakage is found, component replacement is necessary. Consult your NEW HOLLAND CONSTRUCTION Dealer.

MCHP8N-004A

6-55

1

6 - MAINTENANCE

Radiator and coolers Service specifications Check for leakage: Every 10 hours or every day Clean: Every 500 hours

Cleaning 1. Stop the engine and remove the ignition key.

2. Open the rear left-hand side door and block it with the supporting strut, then open the engine hood.

SOEUXT-005A

1

3. Remove the one tach clip (1) and remove the protection grilles (2).

WARNING Flying debris!

Compressed air can propel dirt, rust, etc. into the air. Wear eye and face protection when using compressed air.

Failure to comply could result in death or serious injury.

W0307A

4. Clean the radiators and the oil coolers: Dry dust: use compressed air.

Mud: use a water jet.

Greasy dust: use perchlorethylene.

SOEUXT-006

ATTENTION: The use of trichlorethylene is strictly forbidden.

6-56

2

6 - MAINTENANCE

5. Install the protective grilles (2) then install the one tach clip (1).

WARNING Moving parts!

Make sure all entry and mechanical access doors are properly closed before operating the machine.

Failure to comply could result in death or serious injury.

W0238A

WARNING Moving parts!

Make sure the hood is closed properly before driving the machine.

Failure to comply could result in death or serious injury.

SOEUXT-006

W0280A

6-57

3

6 - MAINTENANCE

Fan and alternator drive belt Service specifications Visual check: Every 10 hours or every day Check belt tension: Every 250 hours

Checking the tension NOTICE: If the engine runs with the belt slack, the belt can slip in its housing and cause the engine to overheat or the battery to receive insufficient charge.

1IUTUH-002A

1

With engine shut down and the ignition key removed, use your finger to exert a pressure of about 100 N (22 lb) at the centre of the belt.

The tension slack should be between about 6 mm (0.2 in) and 8 mm (0.3 in).

NOTE: Check if there are any signs of wear damage to the pulleys or the belt. Check carefully to ensure that the belt is correctly positioned in the pulley grooves. If the belt is stretched, cracked or frayed, it must be replaced.

2

CS98M560TBP1

Adjusting the tension Remove the retaining screws (1) and (2). Use the adjustment screws (3) to move the alternator outwards until belt tension is correct. Tighten the alternator mounting bolts (1) and (2).

Lock nut tightening torque: 75.5 N·m (55.686 lb ft) Installation bolt tightening torque: 126.5 N·m (93.302 lb ft)

5PJHCJ-001

6-58

3

6 - MAINTENANCE

Replacing the belt If the belt breaks, the message "Alternator" is displayed on the message screens. Shut down the engine, remove the ignition key and change the belt.

Remove the retaining screws (1) and (2). Use the adjustment screw (3) to push the alternator inward.

Remove the worn belt.

Install a new belt.

Adjust the belt using the screw (3).

Retighten the retaining screws (1) and (2).

Run the engine for about an hour and then check the belt tension again.

5PJHCJ-001

6-59

4

6 - MAINTENANCE

Adjustment of engine valve rocker clearances Service specifications Check: Every 1000 hours NOTE: Ask your NEW HOLLAND CONSTRUCTION Dealer to check this.

Fuel tank filter Service specifications Clean filter: Periodically Remove the filter and clean it in diesel oil.

NOTE: Use suitable fuel to refill the fuel tank.

B1B5A919

1

Fire extinguisher (not supplied) It is strongly recommended to have a fire extinguisher available and to keep it in the front boot.

Service specifications Every month: • Examine the fire extinguisher and make sure it is not damaged.

Every six months: • Have an approved specialist empty and refill the powder in the fire extinguisher.

CS98M573TBP1

Every year: • Have an approved specialist examine the fire extinguisher.

6-60

1

6 - MAINTENANCE

Protecting the Electrical/Electronic Systems During Charging or Welding DANGER Improper operation or service of this machine can result in an accident.

Any unauthorized modifications made to this machine can have serious consequences. Consult an authorized dealer on changes, additions, or modifications that may be required for this machine. Do not make any unauthorized modifications.

Failure to comply will result in death or serious injury.

D0030A

WARNING Battery acid causes burns. Batteries contain sulfuric acid.

Avoid contact with skin, eyes or clothing. Antidote (external): Flush with water. Antidote (eyes): flush with water for 15 minutes and seek medical attention immediately. Antidote (internal): Drink large quantities of water or milk. Do not induce vomiting. Seek medical attention immediately.

Failure to comply could result in death or serious injury.

W0111A

Whenever carrying out a welding operation on the undercarriage or upperstructure carriage as authorized by the manufacturer and in accordance with his instructions, disconnect the batteries, disconnect the alternator B+ and D+ terminal wires and connect the welding apparatus earth cable to the component on which the welding operation is to be performed. Never connect the welding apparatus to the undercarriage when welding on the upperstructure (or vice-versa). Never connect the welding apparatus earth to a component of the hydraulic system.

To avoid damage to the electronic/electrical systems, always observe the following: 1. Never make or break any of the charging circuit connections, including the battery connections, when the engine is running.

2. Never short any of the charging components to ground.

3. Always place the key of the battery master switch in “O” (Off) position and disconnect the ground cable from the battery before arc welding on the machine (if equipped).

• Position the welder ground clamp as close to the welding area as possible.

• If welding in close proximity to a computer module, then the module should be removed from the machine.

• Never allow welding cables to lay on, near or across any electrical wiring or electronic component while welding is in progress.

4. Always disconnect the negative cable from the battery when charging the battery in the machine with a battery charger.

ATTENTION: If welding must be performed on the unit, either the machine, the battery ground cable must be disconnected from the machine battery. The electronic monitoring system and charging system will be damaged if this is not done.

Remove the battery ground cable. Reconnect the cable when welding is completed.

6-61

6 - MAINTENANCE

Machine inspection and cleaning Service inspections Inspect and clean: Periodically Or whenever oil or grease has been spilt on the machine.

Do not use compressed air if there is oil or soot in the element.

Take the opportunity during this operation to make a visual check of all the welded components (in case of appearance of cracks), the attachment linkages and check the teeth and tooth tips for correct retention and for wear. Look for any leaks and check the condition of all pipes and hoses.

Checking the machine settings Service specifications Have this checked by your NEW HOLLAND CONSTRUCTION Dealer: Every 6 months

Plastic and resin parts When cleaning the plastic windows, the console, the instrument panel, the indicators, etc. do not use gasoline, kerosene, paint solvents, etc. Only use water, soap and a soft cloth.

The use of gasoline, kerosene, paint solvents, etc. will cause discoloration, cracks or deformation of these parts.

6-62

6 - MAINTENANCE

Checking the cylinders for leaks A cylinder rod should be slightly oily. Check that there are no leaks after a period of work, when the whole hydraulic system is at normal operating temperature.

1. Wipe clean the rod and bearing on the cylinder to be cleaned.

2. Operate normally for five or ten minutes.

3. Extend the cylinder rod.

4. Carry out the leak test.

ROD APPEARANCE Dry Slightly greasy Oily Very oily or weeping Leakage

TEST Slight traces of oil when a piece of paper is wiped over 20 cm (7.9 in) of the rod.

Paper remains stuck to rod when run over rod.

Paper remains stuck when placed on rod.

Each time the cylinder rod is extended, a ring of oil can be seen on the rod.

Each time the rod retracts, the excess oil drips from the gland.

6-63

CONCLUSION Normal Normal Normal Consult your NEW HOLLAND CONSTRUCTION Dealer

6 - MAINTENANCE

Tooth tip wear limits on the backhoe bucket Visually evaluate the degree of wear of teeth and tooth tips. The service life of teeth and tooth tips that are wearing unevenly or asymmetrically can be extended. Periodically swap teeth and reverse them. Also reverse the locking pin.

NOTICE: replace teeth and tooth tips before they wear out completely.

NOTICE: never attempt to work without tooth tips or with tooth tips that are completely worn. The adapter could be seriously damaged.

Bucket teeth removal 1. Place the bucket a few centimeters above the ground.

Stop the engine and remove the starter key.

2. Turn the locking stud 90 ° in the clockwise direction using a hexagonal wrench.

3. Remove the locking pin then remove the worn tooth tip.

SMIL13CEX2818AB

1

SMIL13CEX2819AB

2

SMIL13CEX2818AB

3

Bucket teeth installation 1. Clean the mating surface on the adaptor.

2. Engage a new tooth tip right up to the stop and hold it in position.

3. Engage the locking pin until it is flush with the tooth tip.

4. Turn the locking stud 90 ° in the anti-clockwise direction using a hexagonal wrench.

NOTICE: when replacing a tooth tip, it is advisable to replace the locking pin at the same time.

6-64

6 - MAINTENANCE

Replacing a backhoe bucket Removal 1. Place the bucket flat on flat, horizontal ground.

2. Operate the attachment controls so that the arm/bucket linkage pin is not gripped by the weight of the arm.

3. Stop the engine and remove the ignition key.

4. Remove the pins hardware.

C319Z9-013

1

C319Z9-014

2

5. Remove the bucket pins.

6. Start the engine.

7. Disengage the attachment from the bucket and save the linkage seals for re-use.

Installation 1. Make sure the bucket is in a stable position.

2. Start the engine.

3. Bring the arm into its housing.

4. Stop the engine and remove the ignition key.

5. Install the linkage seals between the arm and the bucket. Change them if necessary.

6-65

6 - MAINTENANCE

6.

Install the arm/bucket linkage pin and its hardware.

7.

Start the engine.

8.

Bring the bucket rod into its housing.

9.

Stop the engine and remove the ignition key.

10. Install the linkage seals between the rod and the bucket. Change them if necessary.

11. Install the rod/bucket linkage pin and its hardware.

12. Grease the linkage pins.

TX8XZ1-022

6-66

3

6 - MAINTENANCE

Air conditioning WARNING Maintenance hazard!

Never try to service the air-conditioning system yourself. Contact your dealer for service.

Failure to comply could result in death or serious injury.

W0268A

Service specifications Cleaning the suction and circulation filters: Every 50 hours Cleaning the air circulation filter: Every 50 hours Replace the filters: Every 2000 hours Have a checked by a specialist: Every 6 months The components of the air conditioning system need servicing at regular intervals. Make sure these intervals are respected, in order to ensure the air conditioning functions correctly and with maximum effectiveness. The air conditioning system contains gas which is subject to strict legislation. Any defect in the system must be fixed rapidly.

NOTE: Operate the air conditioning system at least once a week, even if only for a short time.

Inspection In order to ensure the air conditioning functions correctly, inspect the air conditioner using the procedure outlined below before starting work.

Cleanliness of the condenser If the condenser is dirty it will not dissipate heat properly. Clean the condenser in water.

NOTICE: never use water under pressure to clean the condenser.

Checking the belt tension Use your finger to exert pressure of around 10 kg (22.0 lb) on the center of the drive belt. The tension slack should be between about 5 mm (0.2 in)and 7 mm (0.3 in). If necessary, adjust the belt tension.

IPWJCQ-001

Checking the lines Make a visual check of the lines and make sure there are no accumulations of dust, grease, etc.

6-67

1

6 - MAINTENANCE

Cleaning the suction and circulation filters 1. Open the operator's seat air filter compartment cover with the key.

SZ8TNN-001

2

SZ8TNN-002

3

SZ8TNN-003

4

WARNING Flying debris!

Compressed air can propel dirt, rust, etc. into the air. Wear eye and face protection when using compressed air.

Failure to comply could result in death or serious injury.

W0307A

2. Remove the filter and clean it with compressed air. If the filter is damaged, replace it.

3. Install the filter.

4. Close the cover and lock it with the key.

6-68

6 - MAINTENANCE

Cleaning the air circulation filter WARNING Flying debris!

Compressed air can propel dirt, rust, etc. into the air. Wear eye and face protection when using compressed air.

Failure to comply could result in death or serious injury.

W0307A

1. Remove the air circulation filter located on the bottom of the back of the operator's seat and clean it with compressed air. If the filter is damaged, replace it.

BJIW6C-001

5

BJIW6C-003

6

2. Follow the installation procedure and place the filter in the housing.

6-69

6 - MAINTENANCE

Checking the charge state of the system 1. Turn on the air conditioning system, increase engine speed slightly (1400 to 1600 rpm) and look for bubbles through the sight glass.

REE1U2-001

7

REE1U2-005

8

REE1U2-003

9

2. This check should be made approximately one minute after turning on the air conditioning.

(A) Very few bubbles observed, then transparent at first, then whitish: "Normal".

(B) The bubbles are numerous: check the unions and consult your NEW HOLLAND CONSTRUCTION Dealer.

(C) No bubbles are visible: check the unions and consult your NEW HOLLAND CONSTRUCTION Dealer.

3. Check if the air-conditioning line and hose connectors are dirty or dusty and clean them if necessary.

6-70

6 - MAINTENANCE

Gas spring inspection WARNING Explosive gas!

Gas struts contain high-pressure nitrogen gas. If handled improperly, they could explode.

- Do not disassemble.

- Do not expose to flame or fire.

- Do not puncture, weld, or melt.

- Do not expose to shock by striking or turning.

- The fill gas must be removed before disposal. Consult your dealer.

Failure to comply could result in death or serious injury.

W0914A

Gas springs are located on the engine hood (2 locations left and right), cab sunroof (2 locations left and right), and tool box.

For the following, request inspection, service, or replacement from your NEW HOLLAND CONSTRUCTION Dealer.

• When the engine hood or cab sunroof or tool box does not open with little effort.

• When the engine hood or cab sunroof or tool box does not stay open.

• When an oil or gas leak is discovered from the gas spring.

6-71

BC0C8541

1

8B91WE-002

2

8B91WE-003

3

6 - MAINTENANCE

Torque specifications Service specifications Check: Every 250 hours (after the first 50 hours during the run-in period) At the end of each working day, check all mounting nuts and screws for tightness and tighten if necessary. Make sure no hardware items are missing. Replace them, if necessary.

Torque specifications per component Component Travel reduction gear (*) Drive sprocket (*) Idler wheel (*) Upper roller (*) Lower roller (*) Chain guide (*) Tracks Counterweight Turntable (undercarriage) Turnable (upper structure) Swing reduction gear (*) Engine (*) Engine mounts (*) Radiator Hydraulic pump (*) Hydraulic reservoir (*) Fuel tank (*) Control valve Hydraulic swivel (*) Cab Batteries

Torque setting

Wrench

Screw (Ø) M16 M16 M16 M20 M18 M18

mm 24 24 24 30 27 27

in 0.9 0.9 0.9 1.2 1.1 1.1

M20

30

1.2

M33 M20 M20 M20 M10/M16 M16 M16 M10 M20 M16 M16 M16 M12 M12 M16 M10

50 30 30 30 17/24 24 24 17 hexagonal 24 24 24 19 19 24 17

2 1.2 1.2 1.2 0.7/0.9 0.9 0.9 0.7 hexagonal 0.9 0.9 0.9 0.7 0.7 0.9 0.7

NOTE: Use Loctite 262, or the equivalent, on screws marked (*).

6-72

Nm lb ft 267–312 197–230 267–312 197–230 267–312 197–230 521–608 384–448 371–432 274–319 400–462 295–341 250 - 350 + 115° 184 - 258 + 115° - 125° - 125° 1862–2058 1373–1517 468–545 345–402 468–545 345–402 539 - 630 398–465 64–74/206-247 47–54/152-182 265–314 195–231 147–177 108–130 64–73 47–54 367–496 271–366 232–276 171–204 232–276 171–204 267–312 197–230 88–107 65–79 109–127 80–94 149–173 110–128 20–29 14.8–21.4

6 - MAINTENANCE

Fuses NOTE: Before changing fuses or relays, turn the ignition key to the "Shut down" position, wait one minute minimum and place the key of the battery master switch in “O” (Off) position (if equipped).

NOTICE: never replace a fuse with a fuse of a different amperage.

To access the fuse box, open the cover located behind the operator's seat.

1D2MQ9-002A

1

1D2MQ9-003A

2

To access the fuses, remove the cover on the box. A notice on the cover gives the function and amperage of each fuse.

NOTE: To remove or install a fuse, use the notch in the upper right-hand corner of the cover.

6-73

6 - MAINTENANCE

Fuse functions (1) Key switch: 15 A (2) Engine computer: 20 A (3) GPS computer: 10 A (4) Back-up (radio, room lamp): 10 A (5) Function cancellation lever: 10 A (6) Solenoid: 10 A (7) Horn: 10 A (8) Cab top light: 15 A (9) Boom, house light: 15 A (10) Option power suppy 15 A (11) Wiper, washer: 15 A (12) Rotary light: 10 A (13) Cigar lighter, seat suspension: 10 A (14) DC converter: 10 A (15) Air conditioner unit: 5 A (16) Air conditioner blower motor: 15 A

8FPEPL-002

(17) Air conditioner compressor: 5 A (18) Option power supply: 10 A (19) Feed pump: 15 A (20) Option line solenoid: 10 A NOTE: The roof lamp and the radio have an additional external fuse location. A fuse (21) of 10 A is located under the right rear of the operator's seat.

5EB4577C

6-74

4

3

6 - MAINTENANCE

Batteries WARNING Improper operation or service of this machine can result in an accident.

Before working on any component(s) of the electrical circuit, put the ignition key in the off (shut down) position. When disconnecting batteries, always disconnect the negative (-) cable first. When reconnecting batteries, always connect the negative (-) cable last.

Failure to comply could result in death or serious injury.

W0943A

WARNING Battery acid causes burns. Batteries contain sulfuric acid.

Avoid contact with skin, eyes or clothing. Antidote (external): Flush with water. Antidote (eyes): flush with water for 15 minutes and seek medical attention immediately. Antidote (internal): Drink large quantities of water or milk. Do not induce vomiting. Seek medical attention immediately.

Failure to comply could result in death or serious injury.

W0111A

WARNING Battery gas can explode!

To prevent an explosion: 1. Always disconnect the negative (-) battery cable first. 2. Always connect the negative (-) battery cable last. 3. Do not short circuit the battery posts with metal objects. 4. Do not weld, grind, or smoke near a battery.

Failure to comply could result in death or serious injury.

W0011A

WARNING Explosive gas!

Batteries emit explosive hydrogen gas and other fumes while charging. Ventilate the charging area.

Keep the battery away from sparks, open flames, and other ignition sources. Never charge a frozen battery.

Failure to comply could result in death or serious injury.

W0005A

Service specifications Checking the charge state: Every 250 hours Electrolyte level check: Every 250 hours NOTE: When starting the machine with booster batteries, see "Connecting booster batteries".

6-75

6 - MAINTENANCE

Batteries access To access the batteries, open the left-hand rear door then remove the skid plate.

A2ECA66F

1

D59C2D33

2

Checking the charge state of a maintenance-free battery The charge indicator on the battery shows the state of charge of the battery.

If the colour is: • Green; the charge is correct.

• Black; insufficient charge. Recharge the battery until the indicator turns green.

• Transparent (colourless); replace the battery as soon as possible.

Checking the electrolyte level of a maintenance-type battery Remove the cell caps and check the level in each batteries cell. The level should be between 10 mm (0.4 in) and 15 mm (0.6 in) above the plates. Add distilled water if necessary, then install the cell caps.

NOTICE: when adding distilled water at temperatures below 0 °C (32.0 °F), the batteries must be charged or the engine run for two hours approximately in order to ensure that the distilled water and the electrolyte are properly mixed.

NOTE: Make sure the battery terminals are clean and coated with grease and that the cables are properly tightened.

9K4QUU-001A

6-76

3

6 - MAINTENANCE

Changing a battery WARNING Electrical shock hazard!

Do not reverse battery terminals. Connect positive cable ends to positive terminals (+) and negative cable ends to negative terminals (-).

Failure to comply could result in death or serious injury.

W0262A

WARNING Hazard to bystanders!

Always store batteries in a safe location. Keep out of reach of children and other unauthorized persons.

Failure to comply could result in death or serious injury.

W0224A

WARNING Battery acid causes burns. Batteries contain sulfuric acid.

Battery electrolyte contains sulfuric acid. Contact with skin and eyes could result in severe irritation and burns. Always wear splash-proof goggles and protective clothing (gloves and aprons). Wash hands after handling.

Failure to comply could result in death or serious injury.

W0120A

1. Place the key of the battery master switch in “O” (Off) position (if equipped).

2. Remove the terminal protection caps, disconnect cables (negative terminals) and then cables (positive terminals). Remove the anti-sulphate pellets and the battery clips.

3. Install a new battery, put back its clips.

4. Clean the cables and battery terminals and coat them with grease.

5. Install new anti-sulphate pellets, reconnect positive cable ends to positive terminals and then negative cable ends to negative terminals. Install the terminal protection caps.

6. Install the skid plate.

A693538C

7. Place the key of the battery master switch in “I” (On) position (if equipped).

6-77

4

6 - MAINTENANCE

Connecting booster batteries WARNING Improper operation or service of this machine can result in an accident.

An error connecting auxiliary starting cables or short-circuiting battery terminals can cause an accident. Connect auxiliary starting cables as instructed in this manual.

Failure to comply could result in death or serious injury.

W0263A

Make sure that the booster battery voltage corresponds to the voltage system of the machine (24 volts).

1. Place the key of the battery master switch in “O” (Off) position (if equipped).

2. Remove the terminal sleeves.

3. Connect the positive (+) cable to the positive (+) terminal on the first machine battery.

4. Connect the negative (-) cable to the negative (-) terminal on the second machine battery.

5. Place the key of the battery master switch in “I” (On) position (if equipped).

6. Start the engine.

7. Remove the booster battery negative (-) cable and then the positive (+) cable.

8. Install the terminal sleeves.

6-78

6 - MAINTENANCE

Alternator WARNING Improper operation or service of this machine can result in an accident.

Welding sparks can cause battery gases to explode. When welding on the machine, always disconnect the B+ and D+ wires from the alternator. Check the wire markings before reconnecting to ensure a correct connection.

Failure to comply could result in death or serious injury.

W0253A

Service specifications Check: Every 1000 hours ATTENTION: Do not use steam cleaning equipment or a cleaning solvent to clean the alternator.

Ask your NEW HOLLAND CONSTRUCTION Dealer to check the alternator.

NOTE: Make sure that the terminal protectors are correctly installed.

MCHP8N-002A

6-79

1

6 - MAINTENANCE

Starter motor Service specifications Check: Every 1000 hours Ask your NEW HOLLAND CONSTRUCTION Dealer to check the starter motor.

NOTE: Make sure that the terminal protectors are correctly installed.

MCHP8N-003

6-80

1

6 - MAINTENANCE

Bulb replacement Operator’s compartment lighting 1. Remove the cover.

2. Remove the bulb and install a bulb of the same wattage ( 10 W).

3. Install the cover.

8YHY9K-001A

1

Attachment working light 1. Remove the 4 retaining screws.

WNNEYW-001A

2

WNNEYW-002A

3

2. Tilt the working light and disconnect the plug.

6-81

6 - MAINTENANCE

3. Pull the clip outward, remove the bulb and install a bulb of the same wattage ( 70 W).

ATTENTION: Never put your fingers on a tungsten iodide bulb.

4. Install the clip and reconnect the plug.

5. Put the working light back into position and install the mounting screws.

4

WNNEYW-003A

Upperstructure and cab headlight 1. Open the front box.

PV5ETN-001A

5

2. Remove the switch bracket to access the headlamp.

PV5ETN-002

6

3. Disconnect the plug.

PV5ETN-003A

6-82

7

6 - MAINTENANCE

4. Remove the four screws and tilt the headlight.

PV5ETN-004A

8

PV5ETN-005A

9

5. Pull the clip outward, remove the bulb and install a bulb of the same wattage ( 70 W).

ATTENTION: Never put your fingers on a tungsten iodide bulb.

6. Install the clip, put the headlamp back in position and install the screws and the plug.

7. Install the switch bracket.

6-83

6 - MAINTENANCE

Maintenance planning

Maintenance chart

Interval Every 10 hours or daily

Every 50 hours Every 250 hours

Page no.

6-21 6-24 6-28 6-36 6-56 6-58 6-36 6-67 6-11 6-24

Every 500 hours

Every 1000 hours

Every 2000 hours

6-28 6-36 6-45 6-49 6-51 6-52 6-55 6-58 6-72 6-75 6-75 6-11 6-11 6-21 6-21 6-28 6-56 6-11 6-36 6-36 6-45 6-45 6-49 6-51 6-60 6-79 6-80 6-36 6-36 6-36 6-49 6-67

Maintenance Action Engine oil level Coolant level Fuel tank Hydraulic reservoir level Radiators and oil coolers Fan and alternator belt tension Hydraulic system lines Air conditioning (Note A) Bucket linkages (Note B) Tightening of clamps and radiator hoses (Note C) Fuel pre-filter filter element Hydraulic reservoir sediment Primary air filter element (Note D) Swing reduction gear level Travel reduction gears level Pad screw torque (Note F) Track rollers and idler wheels Fan and alternator belt tension Screw and nut tightening torque (Note E) Batteries state Batteries electrolyte level Turntable bearing Turntable bearing teeth Engine oil Engine oil filter Fuel filter element Radiators and oil coolers Attachment (except bucket linkages) (Note F) Hydraulic fluid condition (Note V) Hydraulic reservoir breather Primary air filter element (Note H) Secondary air filter element (Note K) Swing reduction gear (Note K) Travel reduction gears (Note K) Engine valve rocker clearances (Note L) Alternator (Note L) Starter motor (Note L) Suction filter (Note V) Return circuit filter (Note L-M-V) Pilot filter (Note M-V) Swing reduction gear Air conditioning

6-84

Bleed Replace Grease Check Drain Clean No. of pts.

1 X 1 X 1 X 1 X 2 X 1 X — X 1 X 2 X — 2 1 1 1 2 — — 1 — 2 2 2 1 1 1 1 2 15 1 1 1 1 1 2 — 1 1 1 1 1 1 1

X X X X

X X X X X X X X X X X X X X

X X X X X X X X X X X X X X X X

6 - MAINTENANCE

Interval Every 4000 hours

6-36 6-36

Every 5000 hours As required

Maintenance Action

Page no.

6-24 6-36 6-36 3-67 6-28 6-28 6-28 6-52 6-28 6-60 6-62 6-62 6-63

Main pump output hydraulic hoses (Note P) Boom, arm and bucket cylinder hydraulic hoses (Note P) Cooling system (Note G) Inlet filter (Note V) Hydraulic fluid (Note V) Safety valves (Note R) Fuel pre-filter (Note S) Fuel filter (Note S) Fuel supply pump filter (Note T) Tracks (Note T) Fuel tank filter (Note T) Fire extinguisher (Note U) Machine settings (Note R) Machine inspection (Note T) Cylinders for leaks (Note T)

Bleed Replace Grease Check Drain Clean No. of pts.

— X — 1 1 1 2 2 1 1 2 1 1 — — —

X X X X X X X X X X

X

X X

X X X X

Note A: To be checked every 6 months by a specialist.

Note B: If all these linkage points are not equipped with genuine parts, these points must be greased every 10 hours.

Note C: Or every 6 months.

Note D: Or when the message "Air filter" is shown on the message screens.

Note E: Check after the first 50 hours during the run-in period.

Note F: If all these linkage points are not equipped with genuine parts, these points must be greased every 50 hours.

Note G: Or every two years or twice a year (autumn/spring) if antifreeze is used.

Note H: Or after cleaning 6 times.

Note J: Or after the primary filter has been cleaned 3 times.

Note K: Drain after the first 250 hours during the run-in period.

Note L: Ask your NEW HOLLAND CONSTRUCTION Dealer to check this.

Note M: Replace after the first 250 hours during the run-in period.

Note P: Or every 2 years, whichever comes first.

Note R: Have this checked every 6 months by your NEW HOLLAND CONSTRUCTION Dealer.

Note S: When the float reaches the level line (A).

Note T: Periodically.

Note U: Check once a month and have it checked every 6 months by a specialist.

Note V: If the machine is equipped with a hydraulic breaker, it is imperative that the servicing intervals are reduced, refer to page 6-36.

6-85

6 - MAINTENANCE

NOTE: Once the machine has completed 500 hours (then 1000 hours, 1500 hours, etc.) the message "Service due" will appear on the screen (refer to page 3-20) by way of a reminder that service work is due. (It is possible to increase this lapse of time. Consult your NEW HOLLAND CONSTRUCTION Dealer).

6-86

6 - MAINTENANCE

Storage

Preparing for storage The following procedure applies when the machine is to be stored for a month or more. Store the machine on flat, level ground, inside a building or, if not possible, outside and covered with a tarpaulin. Before storing the machine, carry out the following operations: 1. Clean the machine.

2. Make sure that the machine has no damaged or missing parts. Replace them if necessary.

3. Retract the cylinder rods as for as possible and lower the boom until the attachment is resting on the ground.

4. Grease the machine thoroughly. The exposed surfaces of the cylinder rods should be greased or covered with a protective film. Consult your NEW HOLLAND CONSTRUCTION Dealer.

NOTE: When the machine resumes service, the film will disappear automatically.

5. While the engine is still warm, drain the oil sump, replace the oil filter and fill with specified oil. Check the oil level and add more if necessary.

6. Clean or replace the air filter element.

7. Check the level of coolant solution. If the machine is within 100 hours of the next scheduled coolant change, change the coolant now.

8. Remove the batteries, clean the battery housings and make sure not to leave any traces of acid. Store the batteries safely in a cool and dry location, where the temperature is higher than 0 °C (32.0 °F) or disconnect the cable from the negative (-) terminal.

9. Paint any areas where the paintwork is not good.

10. Plug the air filter inlet and the exhaust pipe.

11. Remove the ignition key and place a "Do not operate" label on the right-hand control arm and then place the function cancellation lever in the central position (safety bar in inward position).

12. Lock the hoods, side doors and the cab door.

6-87

6 - MAINTENANCE

Periodic checks WARNING Inhalation hazard! Risk to operators and bystanders.

Avoid running the engine in confined areas. Make sure there is adequate ventilation at all times.

Failure to comply could result in death or serious injury.

W0156A

Every month, check: 1. The battery charge and recharge the batteries if required.

2. The levels and top up if necessary.

3. The condition of all lines, connectors and clamps (rust).

Grease if necessary.

4. The condition of the paintwork. Apply a coat of anti-rust treatment where necessary.

5. Unplug the air filter inlet and the exhaust pipe.

6. Run the engine at low speed following the starting up procedure and operate the attachment, swing and travel controls.

7. The grease on the cylinder rods.

8. Plug the air filter inlet and the exhaust pipe.

6-88

6 - MAINTENANCE

Starting up after storage WARNING Unexpected machine movement!

Before starting the engine, make sure all controls are in the neutral position.

Failure to comply could result in death or serious injury.

W0311A

WARNING Inhalation hazard! Risk to operators and bystanders.

Avoid running the engine in confined areas. Make sure there is adequate ventilation at all times.

Failure to comply could result in death or serious injury.

W0156A

1. Drain the fuel tank, the pre-filter and the fuel filter, replace the filter elements if necessary.

2. Fill the fuel tank with suitable fuel.

3. Install the batteries or reconnect the cable to the negative (-) terminal.

4. Grease the machine thoroughly.

5. Check the condition of the fan drive belt and replace it if necessary.

6. Check the condition of the air conditioning drive belt and replace it if necessary.

7. Check the cooling system level and add more coolant if necessary.

8. Check the engine oil level and add more oil if necessary.

9. Check the hydraulic fluid level and add more fluid if necessary.

10. Check the travel reduction gears and swing reduction gear oil level and add more oil if necessary.

11. Clean the cylinder rods.

12. Unplug the air filter inlet and the exhaust pipe.

13. Remove the "Do not operate" tag and start the engine, following the starting up procedure.

14. Check all the indicators and lamps carefully.

NOTICE: Check the machine and the engine for leaks or for any parts that are broken, defective or missing.

6-89

6 - MAINTENANCE

6-90

7 - TROUBLESHOOTING

7 - TROUBLESHOOTING###_8_### Fault code resolution

Engine troubleshooting NOTE: This chapter shows how to easily diagnose problems relating to the engine and describes the solutions to be adopted. If you are unable to determine the cause of the failure, or if the latter is difficult to rectify, consult your NEW HOLLAND CONSTRUCTION Dealer.

PROBLEM

Engine does not start. Starter does not rotate or rotation is weak.

POSSIBLE CAUSE Battery master switch in “O” (Off) position (if equipped) Battery is running out Disconnection, looseness, or corrosion of the battery terminals Starter ground wire terminal detached, loose, or corroded Engine oil viscosity is too high Starter or electrical system faulty Battery master switch in “O” (Off) position (if equipped) No fuel in fuel tank Air intrusion in the fuel system Clogging of the fuel filter

Engine does not start. Starter turns over.

Fuel is frozen Failure of the supply pump Clogging of the supply pump strainer Failure of the engine control system Preheating system faulty Overflow valve remains open Clogging of the fuel filter Clogging of the pre-fuel filter

The engine starts, but stops immediately.

Failure of the engine control system Clogging of the air cleaner Failure of the supply pump Clogging of the supply pump strainer Failure of the fuel system

Engine revolution is unstable.

Water or air intrusion in the fuel system Failure of the engine control system

Engine rotation does not increase.

Clogging of the fuel filter

7-1

SOLUTION Place the battery master switch in “I” (On) position (if equipped) Charge or replace Repair the corroded area, and then tighten securely Repair the corroded area, and then tighten securely Replace it with oil with appropriate viscosity Consult your NEW HOLLAND CONSTRUCTION Dealer Place the battery master switch in “I” (On) position (if equipped) Check that there is no fuel leakage and refuel Remove the air Remove moisture and replace the element Warm up the fuel pipe with hot water, or wait until the air temperature rises Consult your NEW HOLLAND CONSTRUCTION Dealer Clean the strainer Consult your NEW HOLLAND CONSTRUCTION Dealer Clean or replace the supply pump, fuel filter or fuel port overflow valve Remove moisture and replace the element Clean or replace the element Consult your NEW HOLLAND CONSTRUCTION Dealer Clean or replace the element Consult your NEW HOLLAND CONSTRUCTION Dealer Clean the strainer Consult your NEW HOLLAND CONSTRUCTION Dealer Remove the air Consult your NEW HOLLAND CONSTRUCTION Dealer Remove moisture and replace the element

7 - TROUBLESHOOTING

PROBLEM

The exhaust smoke is white.

The exhaust smoke is black.

POSSIBLE CAUSE Insufficient warming-up Too much engine oil Failure of the engine control system Failure of the supply pump Failure of the fuel system Continuous idling for a long period (more than two hours) Failure of the engine control system Failure of the supply pump Clogging of the air cleaner Failure of the fuel system Clogging of the exhaust system Diesel Particulate Diffuser is faulty No coolant Front of the radiator is clogged with filth Reserve tank cap not fully tightened

Overheat occurs.

Coolant is dirty Failure of the fan clutch Reserve tank cap dirty or faulty Excessive engine oil Inappropriate engine oil viscosity

Oil pressure does not increase.

Amount of engine oil is insufficient Failure inside the engine Failure of meters, lights or switches Oil leakage from the oil filter hose Clogging of the air cleaner

SOLUTION Perform warming-up Adjust to the appropriate oil amount Consult your NEW HOLLAND CONSTRUCTION Dealer Raise the engine speed and confirm that white smoke is not emitted Consult your NEW HOLLAND CONSTRUCTION Dealer Clean or replace the element Consult your NEW HOLLAND CONSTRUCTION Dealer Refill Perform cleaning Tighten it securely or replace the cap with a new one Clean inside the radiator and replace the coolant Consult your NEW HOLLAND CONSTRUCTION Dealer Clean or replace the reserve tank cap Keep the oil at appropriate level Replace it with oil with appropriate viscosity Refill Consult your NEW HOLLAND CONSTRUCTION Dealer

Clean the element Remove moisture and replace the Clogging of the fuel filter element Clogging of the pre-fuel filter Clean the element Engine does not have enough power.

Consult your NEW HOLLAND Failure of the engine control system CONSTRUCTION Dealer Clogging of the supply pump strainer Clean the strainer Failure of the engine Consult your NEW HOLLAND CONSTRUCTION Dealer Diesel Particulate Diffuser is faulty

7-2

8 - SPECIFICATIONS

8 - SPECIFICATIONS###_9_### Machine specifications Engine High-pressure common rail engine: Compliant with Tier 3 exhaust emission level.

Manufacturer and type Injection Number of cylinders Bore x stroke Displacement Rated speed Rated power ( ISO 9249 ) Cooling Battery start Voltage Alternator Starter

ISUZU GI-4HK1X Electronic control 4 115 mm (4.53 in) x 125 mm (4.92 in) 5193 cm³/rev (317 in³/rev) 1800 RPM 117.3 kW (159.5 Hp) Water-cooled 2 x 12 V 92 A·h 24 V 50 A 24 V, 5.0 kW

Hydraulic system Rated working pressure Maximum working pressure (Power boost) Maximum flow of the main pump (at 1800 RPM) Maximum flow of the pilot pump (at 1800 RPM) Rated pilot pressure

34.3 MPa (4975.2 psi) 36.8 MPa (5337.8 psi) 2 x 211 L/min (55.7 US gpm) 18 L/min (4.8 US gpm) 3.9 MPa (565.7 psi)

Control valve Four control valve sections for right-hand travel, boom/bucket and arm acceleration.

Five control valve sections for left-hand travel, swing, arm, auxiliary attachment and boom acceleration.

Boom/arm load holding valves.

Swing Fixed displacement piston motor Mechanical disk brake Upper structure swing speed

11.5 RPM

Travel Axial piston 2-speed hydraulic motor Planetary reduction gears Low speed High speed Grade ability

0 - 3.4 km/h (0 - 2.1 mph) 0 - 5.6 km/h (0 - 3.5 mph) 70 % ( 35 ° )

8-1

8 - SPECIFICATIONS

Boom and arms Boom length Arms length

5.70 m (224.41 in) HD. 2.40 m (94.49 in) HD, 2.94 m (115.75 in) semi-HD and 2.94 m (115.75 in) HD.

Digging force (Power boost engaged) Bucket digging force Arm digging force 2.40 m (94.49 in) Arm digging force 2.94 m (115.75 in)

15200 daN (34171 lbf) 13200 daN (29675 lbf) 11000 daN (24729 lbf)

Travel lower body One-piece frame with welded components Lubricated track roller and idler wheel Track tension adjustment system by grease cylinder 600 mm (23.62 in) 700 mm (27.56 in) 800 mm (31.50 in) 900 mm (35.43 in) (*) 0.44 bar (6.38 psi)

Steel track Ground pressure with 600 mm (23.62 in) tracks NOTICE: (*) for application on swampy ground.

8-2

8 - SPECIFICATIONS

Safety devices Lower the attachment when the engine fails Operation is disabled with the gate lock lever or left side console up Engine emergency stop, anti-theft function Safety glass, dual horn Inertial reel type seat belt Rear view mirror (cab side and right side) Rear view camera Battery master switch Safety valve with overload indicator and lifting eye Fire extinguisher

option option option

Operator's compartment Deluxe operator's seat with armrests, inertia type safety belt, multi-position adjustment and headrest (vibration level, ISO 7096:2000 Class EM6) (seat coefficient < 0.7). Speed programmer, also provides automatic speed change.

Single-speed wiper plus intermittent mode, washers, heating, defrost, ventilation/air conditioning, cab lights, cigarette lighter, screen control camera back.

Hydraulically assisted controls Attachment and swing Travel

2 control levers 2 foot pedals

Working lights One on upper structure Two on attachment Two on cab

24 V, 70 W 24 V, 70 W 24 V, 70 W

Cab Smooth and round shape design cab, fabricated by press work Safety glass for all windows Shock-less cab suspension by 4-point fluid mounting Sliding front window with auto lock Built-in type full-color LCD monitor display Membrane switch on monitor display Windshield wiper and washer AM/FM Radio with auto tuner Floor mat Hinged skylight Sun shield Auto air conditioner Roll-over protective structure ( ROPS ) Top guard OPG level 1 (in cab structure)

8-3

option

8 - SPECIFICATIONS

Fluids and lubricants By using appropriate fluids and lubricants the excavator can operate in ambient temperatures ranging from -15 °C (5 °F) to 40 °C (104 °F). Refer to the list of fluids and lubricants contained in this manual.

NOTICE: When operating the machine in ambient temperatures outside the above mentioned range, consult your NEW HOLLAND CONSTRUCTION Dealer for specific machine provision and for specific fluids and lubricants to be used.

NEW HOLLAND CONSTRUCTION specification

Reference specification

—

—

ASTM D975

NEW HOLLAND AMBRA MASTERGOLD™ HSP ENGINE OIL

MAT3507

Quantity

Fuel tank Engine oil Swing reduction unit Travel reduction unit Engine coolant Hydraulic oil tank (**) Grease

410 L (108 US gal) 23.1 L (6.1 US gal) 5L (1.3 US gal) 5L (1.3 US gal) 30.8 L (8.1 US gal) 147 L (38.8 US gal) —

NEW HOLLAND AMBRA HYPOIDE 90 NEW HOLLAND AMBRA HYPOIDE 90 NEW HOLLAND AMBRA AGRIFLU-OT (*) NEW HOLLAND AMBRA HI-TECH EX LL 46 NEW HOLLAND AMBRA GR-9 MULTI-PURPOSE GREASE

(*) Concentrate antifreeze to be mixed 50/50 with distilled (deionized) water. (**) The total capacity of the hydraulic system is 240 L (63.4 US gal).

8-4

MS 1316 NH 520 A MS 1316 NH 520 A — — MAT3550 Grade A

SAE 15W40 API CI-4 SAE 80W/90 API GL-5 SAE 80W/90 API GL-5 ASTM D 3306 TYPE I ISO 11158 L-HV46 NLGI 2

8 - SPECIFICATIONS

Engine coolant NEW HOLLAND AMBRA AGRIFLU-OT is the reference genuine product.

NOTICE: Use of different coolant brands is not recommended.

NOTICE: Never add Supplemental Coolant Additives (SCA) when using NEW HOLLAND AMBRA AGRIFLU-OT. NOTICE: Never mix NEW HOLLAND AMBRA AGRIFLU-OT coolant with conventional coolant. Mixing organic based coolant with conventional coolant will reduce the effectiveness of NEW HOLLAND AMBRA AGRIFLU-OT coolant.

NOTICE: If only conventional coolant is available, a complete changeover of the fluid into the cooling system shall be carried out. Refer to the procedure described in the Chapter 6 (Engine coolant replacement).

The engine cooling system shall always be refilled with coolant solution made by mixture of antifreeze and distilled (deionized) water.

NOTICE: Never refill the cooling system with only antifreeze. Never refill the cooling system with only water.

Using NEW HOLLAND AMBRA AGRIFLU-OT, a 50/50 mixture of antifreeze and distilled (deionized) water grants proper performance of the engine cooling system in the above mentioned operating temperature range of the machine.

NOTICE: If operating in extreme winter climate, a coolant solution made by 60/40 antifreeze/distilled (deionized) water mixture shall be used in order to grant proper performance of the engine cooling system.

NOTICE: Never use coolant solution with more than 60 % of antifreeze. This affects the cooling capacity of the mixture.

The antifreeze concentration in the mixture of antifreeze and distilled (deionized) water can be determined with a refractometer designed to measure ethylene glycol content.

If distilled (deionized) water is not available, use water for dilution with the following properties: Property Total Solids Total Hardness Chloride (Cl) Sulfate (SO4) Acidity pH

Maximum limit 340 ppm 340 ppm 340 ppm 100 ppm 5.5 to 9.0

NOTICE: Never use hard water, sea water and softened sea water that has been conditioned with salt. The minerals and salts present in potable water can cause corrosion and deposits resulting in shortened engine life.

8-5

8 - SPECIFICATIONS

Fuel Use only Low Sulphur Diesel that meets the National Regulations for commercial diesel fuel.

NOTICE: never use Diesel fuel having a sulphur content higher than 350 ppm.

Using other types of fuel may lead to stalled engine output or deterioration in fuel economy.

NOTICE: The warranty shall be invalid if any serious defect is caused by usage of any other fuel. Using fuel other than recommended may cause damage to the fuel injection pump, injector, other fuel supply system or the engine.

NEW HOLLAND CONSTRUCTION may not be responsible to any of such damages.

NOTICE: If operating in severe winter climate, consult the fuel supplier or the CASE CONSTRUCTION dealer for specific diesel fuel to be used.

Conditions applicable to diesel fuel. The diesel fuel used must: • be free from dust particles, even minute ones, • have the proper viscosity, • have a high cetane number, • present great fluidity at low temperatures, • have low sulphur content, • have very little residual carbon.

It is recommended that the following safety information be considered in order to prevent damage to the engine fuel supply system.

• Some fuel suppliers mix old engine oil and diesel fuel.

• Makers of larger engine permit the use of this kind of fuel.

• However, do not use diesel fuel contaminated with engine oil in customer's engines.

• Not only will this fuel damage the engine, it may also have a negative impact on the exhaust gas purification function.

• Before using diesel fuel, confirm with the supplier whether the fuel complies with the above specifications.

NOTICE: Consult the supplier or the NEW HOLLAND CONSTRUCTION Dealer regarding appropriate use of fuel additives.

NOTICE: In order to prevent condensation during cold weather, fill the fuel tank to full after the completing the day's work.

Fuel storage: Long storage can lead to the accumulation of impurities and condensation in the fuel. Engine trouble can often be traced to the presence of water in the fuel. The storage tank must be placed outside and the temperature of the fuel should be kept as low as possible. Drain off water and impurities regularly.

8-6

8 - SPECIFICATIONS

Environment and ecology Before carrying out any maintenance operation on this machine and before disposing of used fluids or lubricants, always think of the environment. Never throw oil or fluid on the ground and never place it in leaking receptacles.

Consult your local ecological recycling center or your NEW HOLLAND CONSTRUCTION Dealer to obtain information on the correct method of disposing of these lubricants.

The following are recommendations which may be of assistance: • Become acquainted with and ensure that you understand the relative legislation applicable to your country.

• Where no legislation exists, obtain information from suppliers of oils, filters, batteries, fuels, antifreeze, cleaning agents, etc., with regard to their effect on man and nature and how to safely store, use and dispose of these substances.

• Local Environmental Agency will, in many cases, be able to help you as well.

8-7

8 - SPECIFICATIONS

Dimensions Overall machine dimensions

399DF6DA

1

Arms 2.40 m (94.49 in) (A) (B) (C) (D) (E) (F) (G) (H) (I) (J) (standard tracks) (K) ( 600 mm (23.62 in) track) (K) ( 700 mm (27.56 in) track) (K) ( 800 mm (31.50 in) track) (K) ( 900 mm (35.43 in) track) (L) (M)

3.19 m 9.48 m 2.95 m 2.77 m 1.04 m 2.72 m 4.47 m 3.66 m 2.39 m 0.60 m 2.99 m 3.09 m 3.19 m 3.29 m 0.44 m 2.96 m

(125.59 in) (373.23 in) (116.14 in) (109.06 in) (40.94 in) (107.09 in) (175.98 in) (144.09 in) (94.09 in) (23.62 in) (117.72 in) (121.65 in) (125.59 in) (129.53 in) (17.32 in) (116.54 in)

8-8

2.94 m (115.75 in) 2.97 m (116.93 in) 9.40 m (370.08 in)

8 - SPECIFICATIONS

Working range

8DB91874

8-9

2

8 - SPECIFICATIONS

Arms 2.40 m (94.49 in) (A) (Maximum digging reach) (B) (Maximum digging depth) (C) (Maximum dump height) (D) (Maximum working height) (E) (Minimum attachment swing radius) (F) (Maximum digging depth on a vertical face) (G) (Maximum length of flat-bottomed trench)

9.42 m (370.87 in) 6.11 m (240.55 in) 6.59 m (259.45 in) 9.41 m (370.47 in) 3.60 m (141.73 in) 5.50 m (216.54 in) 2.44 m (96.06 in)

2.94 m (115.75 in) 9.90 m (389.76 in) 6.65 m (261.81 in) 6.81 m (268.11 in) 9.61 m (378.35 in) 3.60 m (141.73 in) 5.96 m (234.65 in) 2.44 m (96.06 in)

Weights With mono-block boom, 2.4 m (94.49 in) arm, 1.02 m³ (36.0 ft³) Heavy Duty bucket, 600 mm (23.6 in) tracks, operator, lubricant, coolant and full fuel tank.

Counterweight

8-10

21700 kg (47840 lb) 4250 kg (9370 lb)

9 - ACCESSORIES

9 - ACCESSORIES###_10_### Direct fit buckets Direct fit buckets application as function of the arm Heavy Duty buckets Capacity ISO 7451 (Heaped) 0.42 m³ (0.55 yd³) 0.56 m³ (0.73 yd³) 0.69 m³ (0.90 yd³) 0.83 m³ (1.09 yd³) 1.02 m³ (1.33 yd³) 1.10 m³ (1.44 yd³)

Arm

Width

Mass

610 mm (24 in) 760 mm (30 in) 915 mm (36 in) 1065 mm (42 in) 1220 mm (48 in) 1370 mm (54 in)

680 kg (1499 lb) 760 kg (1676 lb) 870 kg (1918 lb) 930 kg (2050 lb) 1030 kg (2271 lb) 1110 kg (2447 lb)

2.40 m (94.49 in) ○ ○ ○ ○ ● ■

Heavy Duty, High Capacity buckets Capacity ISO 7451 (Heaped) 0.57 m³ (0.75 yd³) 0.72 m³ (0.94 yd³) 0.88 m³ (1.15 yd³) 1.05 m³ (1.37 yd³) 1.22 m³ (1.60 yd³)

Arm

Width

Mass

610 mm (24 in) 760 mm (30 in) 915 mm (36 in) 1065 mm (42 in) 1220 mm (48 in)

830 kg (1830 lb) 910 kg (2006 lb) 1020 kg (2249 lb) 1100 kg (2425 lb) 1200 kg (2646 lb)

2.40 m (94.49 in) ○ ○ ○ ● ■

Severe Duty buckets Capacity ISO 7451 (Heaped) 0.42 m³ (0.55 yd³) 0.56 m³ (0.73 yd³) 0.69 m³ (0.90 yd³) 0.83 m³ (1.09 yd³) 1.02 m³ (1.33 yd³)

Mass

610 mm (24 in) 760 mm (30 in) 915 mm (36 in) 1065 mm (42 in) 1220 mm (48 in)

760 kg (1676 lb) 850 kg (1874 lb) 960 kg (2116 lb) 1050 kg (2315 lb) 1150 kg (2535 lb)

2.40 m (94.49 in) ○ ○ ○ ○ ●

Ditch cleaning buckets Width

0.78 m³ (1.02 yd³)

1525 mm (60 in)

0.93 m³ (1.22 yd³)

1830 mm (72 in)

2.94 m (115.75 in) ○ ○ ● ■ ■ Arm

Width

Capacity ISO 7451 (Heaped)

2.94 m (115.75 in) ○ ○ ○ ○ ● ■

2.94 m (115.75 in) ○ ○ ○ ● ■ Arm

Mass 460 kg (1014 lb) 560 kg (1235 lb) (*) 520 kg (1146 lb) 640 kg (1411 lb) (*)

(*) with bolt-on cutting edge ○ Density of material up to 2 t/m3 ● Density of material up to 1.6 t/m3 ■ Density of material up to 1.2 t/m3 x Not applicable

9-1

2.40 m (94.49 in) ○ ○ ○ ○

2.94 m (115.75 in) ○ ○ ○ ○

9 - ACCESSORIES

9-2

Index ###_Index_###

. . . . . . .

. . . . . . .

. . . . . . .

A . . . . . . . . . . . . . .

. . . . . . .

. . . . . . .

. . . . . . .

. . . . . . .

. . . . . . .

. . . . . . .

. . . . . . .

. . . . . . .

. . . . . . .

. . . . . . .

. . . . . . .

. . . . . . .

. . . . . . .

. . . . . . .

. . . . . . .

. . . . . . .

. . . . . . .

. . . . . . .

. . . . . . .

. . . . . . .

. . . . . . .

. . . . . . .

Basic instructions . . . . . . . . . . . . . . .

Batteries. . . . . . . . . . . . . . . . . . .

Battery master switch . . . . . . . . . . . . .

Break-in period . . . . . . . . . . . . . . . .

Bringing the machine up to operating temperature Bulb replacement . . . . . . . . . . . . . . .

. . . . . .

. . . . . .

B . . . . . . . . . . . .

. . . . . .

. . . . . .

. . . . . .

. . . . . .

. . . . . .

. . . . . .

. . . . . .

. . . . . .

. . . . . .

. . . . . .

. . . . . .

. . . . . .

. . . . . .

. . . . . .

. . . . . .

. . . . . .

. . . . . .

. . . . . .

. . . . . .

. . . . . .

. . . . . .

. 6-1 . 6-75 . 3-64 . 4-3 . 4-9 . 6-81

Cab internal lighting . . . . . .

Cab - Operating . . . . . . .

Cab radio . . . . . . . . . .

Checking the cylinders for leaks Checking the machine settings .

Clock adjustment . . . . . . .

Coat hanger hook. . . . . . .

Cooling system . . . . . . . .

Cup holder . . . . . . . . . .

. . . . . . . . .

. . . . . . . . .

C . . . . . . . . . . . . . . . . . .

. . . . . . . . .

. . . . . . . . .

. . . . . . . . .

. . . . . . . . .

. . . . . . . . .

. . . . . . . . .

. . . . . . . . .

. . . . . . . . .

. . . . . . . . .

. . . . . . . . .

. . . . . . . . .

. . . . . . . . .

. . . . . . . . .

. . . . . . . . .

. . . . . . . . .

. . . . . . . . .

. . . . . . . . .

. . . . . . . . .

. . . . . . . . .

. . . . . . . . .

. . . . . . . . .

. . . . . . . . .

3-45 4-1 3-49 6-63 6-62 3-37 3-56 6-24 3-53

D Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Direct fit buckets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8-8 9-1

Adjustment of engine valve rocker clearances Air conditioning . . . . . . . . . . . . . .

Air filter . . . . . . . . . . . . . . . . .

Air suspension seat (option) . . . . . . . .

Alternator . . . . . . . . . . . . . . . .

Anti-theft protection . . . . . . . . . . . .

Auxiliary hydraulic circuits . . . . . . . . .

. . . . . . . . .

. . . . . . . . .

. . . . . . . . .

. . . . . . . . .

. . . . . . . . .

. . . . . . . . .

. . . . . . .

. . . . . . . . .

. . . . . . . . .

Ecology and the environment. . . . . . . . . . . .

Electro-Magnetic Compatibility (EMC) . . . . . . . .

Emergency exit hammer . . . . . . . . . . . . . .

Engine . . . . . . . . . . . . . . . . . . . . .

Engine hood . . . . . . . . . . . . . . . . . . .

Engine oil recommended operating temperature range Engine operation . . . . . . . . . . . . . . . . .

Engine troubleshooting . . . . . . . . . . . . . .

E . . . . . . . . . . . . . . . .

Fan and alternator drive belt . . .

Fire extinguisher (not supplied) .

Fluids and lubricants . . . . . .

Frame - Access/Exit. . . . . . .

Front lower window . . . . . . .

Front right-hand console . . . . .

Front storage box . . . . . . . .

Fuel system . . . . . . . . . .

Fuel tank . . . . . . . . . . .

Fuel tank filler pump (if equipped) .

Fuel tank filter . . . . . . . . .

Fuse box . . . . . . . . . . .

Fuses . . . . . . . . . . . . .

. . . . . . . . . . . . .

. . . . . . . .

6-60 6-67 6-45 3-9 6-79 4-4 4-24

. . . . . . . .

. . . . . . . .

. . . . . . . .

. . . . . . . .

. . . . . . . .

. . . . . . . .

. . . . . . . .

. . . . . . . .

. . . . . . . .

. . . . . . . .

. . . . . . . .

. . . . . . . .

. . . . . . . .

. . . . . . . .

. . . . . . . .

. . . . . . . .

. . . . . . . .

. . . . . . . .

. . . . . . . .

. . . . . . . .

. . . . . . . .

2-10 1-2 3-46 6-21 3-65 6-8 4-10 7-1

. . . . . . . . . . . . .

. . . . . . . . . . . . .

. . . . . . . . . . . . .

. . . . . . . . . . . . .

. . . . . . . . . . . . .

. . . . . . . . . . . . .

. . . . . . . . . . . . .

. . . . . . . . . . . . .

. . . . . . . . . . . . .

. . . . . . . . . . . . .

. . . . . . . . . . . . .

. . . . . . . . . . . . .

. . . . . . . . . . . . .

. . . . . . . . . . . . .

. . . . . . . . . . . . .

. . . . . . . . . . . . .

. . . . . . . . . . . . .

. . . . . . . . . . . . .

. . . . . . . . . . . . .

. . . . . . . . . . . . .

. . 6-58 . . 6-60 6-4, 8-4 . . 3-1 . . 3-18 . . 3-19 . . 3-62 . . 6-28 . . 3-58 . . 3-68 . . 6-60 . . 3-54 . . 6-73

F . . . . . . . . . . . . .

. . . . . . . . . . . . .

. . . . . . . . . . . . .

. . . . . . . . . . . . .

. . . . . . . . . . . . .

. . . . . . . . . . . . .

. . . . . . . . . . . . .

. . . . . . . . . . . . .

. . . . . . . . . . . . .

. . . . . . . . . . . . .

G Gas spring inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-71 Gate lock lever and safety bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-40 Grease points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-11 Hand control levers and pedals . . . . . . .

Handling the machine . . . . . . . . . . .

Hand signals . . . . . . . . . . . . . . .

Heating, ventilation or air-conditioning control Hydraulic circuit . . . . . . . . . . . . .

. . . . .

. . . . .

. . . . .

. . . . .

H . . . . . . . . . .

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

3-13 4-17 2-11 3-41 6-36

I Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-2

L Left-hand control arm . . . . . . . . . . . .

Levels . . . . . . . . . . . . . . . . . . .

Load handling . . . . . . . . . . . . . . .

Loading the machine onto a transport trailer . .

Lowering the attachment in the event of a failure Lower panels. . . . . . . . . . . . . . . .

. . . . . .

. . . . . .

. . . . . .

. . . . . .

. . . . . .

. . . . . .

. . . . . .

. . . . . .

. . . . . .

. . . . . .

. . . . . .

. . . . . .

. . . . . .

. . . . . .

. . . . . .

. . . . . .

. . . . . .

. . . . . .

. . . . . .

. . . . . .

. . . . . .

. . . . . .

. . . . . .

. . . . . .

. . . . . .

. . . . . .

. . . . . .

3-38 6-19 4-19 5-1 4-23 3-66

Machine components . . . . .

Machine inspection and cleaning Machine operation . . . . . .

Machine orientation . . . . . .

Machine specifications . . . .

Machine travel . . . . . . . .

Magazine rack . . . . . . . .

Maintenance chart . . . . . .

Mechanical suspension seat . .

Menu screen display . . . . .

Monitor switches . . . . . . .

. . . . . . . . . . .

. . . . . . . . . . .

. . . . . . . . . . .

M . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . .

. . . . . . . . . . .

. . . . . . . . . . .

. . . . . . . . . . .

. . . . . . . . . . .

. . . . . . . . . . .

. . . . . . . . . . .

. . . . . . . . . . .

. . . . . . . . . . .

. . . . . . . . . . .

. . . . . . . . . . .

. . . . . . . . . . .

. . . . . . . . . . .

. . . . . . . . . . .

. . . . . . . . . . .

. . . . . . . . . . .

. . . . . . . . . . .

. . . . . . . . . . .

. . . . . . . . . . .

. . . . . . . . . . .

. . . . . . . . . . .

. . . . . . . . . . .

1-6 6-62 4-12 1-5 8-1 4-14 3-54 6-84 3-5 3-27 3-25

N Note to the Owner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-1

. . . . . . . . . . .

. . . . . . . . . . .

. . . . . . . . . . .

. . . . . . . . . . .

. . . . . . . . . . .

. . . . . . . . . . .

Operating the machine . . . . . . . . . .

Operating the machine in hot or cold weather.

Operator's manual storage on the machine. .

Optional tool supply valves (optional) . . . .

. . . . . . . . . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. 4-21 . 4-11 . 1-5 . 3-67

P Parking the machine . . . . . . . . . . . . . . . . . . . . . . .

Plastic and resin parts . . . . . . . . . . . . . . . . . . . . . . .

Position of the operator’s compartment controls and accessories . . . .

Preparing for storage . . . . . . . . . . . . . . . . . . . . . . .

Product identification . . . . . . . . . . . . . . . . . . . . . . .

Protecting the Electrical/Electronic Systems During Charging or Welding .

. . . . . .

. . . . . .

. . . . . .

. . . . . .

. . . . . .

. . . . . .

. . . . . .

. . . . . .

. . . . . .

. . . . . .

. . . . . .

. . . . . .

. . . . . .

. . . . . .

. . . . . .

. . . . . .

4-29 6-62 3-3 6-87 1-3 6-61

. . . . . . . . . .

. . . . . . . . . .

. . . . . . . . . .

. . . . . . . . . .

. . . . . . . . . .

. . . . . . . . . .

. . . . . . . . . .

. . . . . . . . . .

. . . . . . . . . .

. . . . . . . . . .

. . . . . . . . . .

. . . . . . . . . .

. . . . . . . . . .

. . . . . . . . . .

. . . . . . . . . .

. . . . . . . . . .

6-56 3-62 3-59 3-55 6-9 6-65 3-52 3-47 3-57 3-57

. . . . . . . . . .

. . . . . . . . . .

. . . .

. . . . . . . . . .

. . . .

. . . . . . . . . .

. . . .

O . . . . . . . .

. . . .

Radiator and coolers . . . . . . . . . .

Rear view camera (optional) . . . . . . .

Rear view mirrors . . . . . . . . . . . .

Refrigerated/heated compartment. . . . .

Releasing pressure in the hydraulic system Replacing a backhoe bucket . . . . . . .

Right-hand console . . . . . . . . . . .

Right-hand control arm . . . . . . . . .

Roof curtain . . . . . . . . . . . . . .

Roof hatch . . . . . . . . . . . . . . .

. . . .

. . . . . . . . . .

R . . . . . . . . . . . . . . . . . . . .

. . . .

. . . . . . . . . .

. . . .

. . . . . . . . . .

. . . .

. . . . . . . . . .

. . . .

. . . . . . . . . .

. . . .

. . . . . . . . . .

. . . . . . . . . .

. . . . . . . . . . . . . .

. . . . . . . . . . . . . .

. . . . . . . . . . . . . .

. . . . . . . . . . . . . .

. . . . . . . . . . . . . .

. . . . . . . . . . . . . .

S . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Tie downs for shipping. . . . . . . . . .

Tooth tip wear limits on the backhoe bucket Torque specifications . . . . . . . . . .

Towing . . . . . . . . . . . . . . . .

Track rollers and idler wheels. . . . . . .

Tracks. . . . . . . . . . . . . . . . .

Travel reduction gears. . . . . . . . . .

. . . . . . .

. . . . . . .

. . . . . . .

. . . . . . .

. . . . . . .

. . . . . . .

Safety rules . . . . . . . . . . . . .

Safety rules and signal word definitions .

Safety signs . . . . . . . . . . . . .

Safety valves (optional) . . . . . . . .

Side doors . . . . . . . . . . . . . .

Sliding windows on door . . . . . . . .

Starter motor . . . . . . . . . . . . .

Starting the engine . . . . . . . . . .

Starting up after storage . . . . . . . .

Stopping the engine . . . . . . . . . .

Storage compartment . . . . . . . . .

Sun shield (optional) . . . . . . . . .

Swing reduction gear . . . . . . . . .

System display and function control panel

. . . . . . . . . . . . . .

. . . . . . . . . . . . . .

. . . . . . . . . . . . . .

. . . . . . . . . . . . . .

. . . . . . . . . . . . . .

. . . . . . . . . . . . . .

. . . . . . . . . . . . . .

. . . . . . . . . . . . . .

. . . . . . . . . . . . . .

. . . . . . . . . . . . . .

. . . . . . . . . . . . . .

. . . . . . . . . . . . . .

. . . . . . . . . . . . . .

. . . . . . . . . . . . . .

. . . . . . . . . . . . . .

. . . . . . . . . . . . . .

. . . . . . . . . . . . . .

. . . . . . . . . . . . . .

. . . . . . . . . . . . . .

. . . . . . . . . . . . . .

. . . . . . . . . . . . . .

. . . . . . . . . . . . . .

2-2 2-1 2-15 3-67 3-63 3-46 6-80 4-7 6-89 4-13 3-55 3-57 6-49 3-20

. . . . . . .

. . . . . . .

. . . . . . .

. . . . . . .

. . . . . . .

. . . . . . .

. . . . . . .

. . . . . . .

. . . . . . .

. . . . . . .

. . . . . . .

. . . . . . .

. . . . . . .

. . . . . . .

. . . . . . .

. . . . . . .

. . . . . . .

. . . . . . .

. . . . . . .

. . . . . . .

. . . . . . .

. . . . . . .

5-4 6-64 6-72 5-7 6-55 6-52 6-51

U Unloading the machine from a transport trailer . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5-6

T . . . . . . .

W Weights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10 Windshield . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-17 Windshield washer reservoir . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-66

Dealer’s stamp

CNH Industrial Italia S.p.A. reserves the right to make improvements in design and changes in specifications at any time without notice and without incurring any obligation to install them on units previously sold.

Specifications, descriptions, and illustrative material herein are as accurate as known at time of publication, but are subject to change without notice.

Availability of some models and equipment builds varies according to the country in which the equipment is being used. For exact information about any particular product, please consult your New Holland dealer.

© 2016 CNH Industrial Italia S.p.A. All Rights Reserved.

New Holland is a trademark registered in the United States and many other countries, owned by or licensed to CNH Industrial N.V., its subsidiaries or affiliates.

Any trademarks referred to herein, in association with goods and/or services of companies, other than owned by or licensed to CNH Industrial N.V., its subsidiaries or affiliates, are the property of those respective companies.