REMOTE KEYLESS ENTR Y — (OPTIONAL)

This vehicle equipped with a Remote Keyless Entry system. This system operates means a hand - held remote control that locks and unlocks the cab doors.

The remote control door lock transmitters are supplied pairs; each one attached a key C0029323

LED

Press once unlock driver side door Press twice unlock both

Press and hold for 3 seconds activate panic mode. Press and hold for 3 seconds again cancel panic mode.

Press and hold for 0.5 second turn external lights

Press once lock Press twice for horn

Each transmitter powered a 3 - volt battery and water Information concerning battery troubleshooting and programming the transmitters provided this

The receiver the vehicle capable recognizing four transmitters. Replacement transmitters are available; however , they must programmed match the specific receiver (refer the "Programming the T ransmitter" section).

ransmitter Operations

The door transmitter has four buttons (labeled LOCK, UNLOCK, AUX and HORN) control operation the system. When any the buttons pressed, a coded Ultra - high frequency (UHF) radio signal transmitted the receiver the vehicle.

The transmitter must within approximately meters (33 feet) the vehicle for the receiver detect the coded The Remote Keyless Entry system has fect the normal operation the power door

When the LOCK button pressed, the doors will lock and the lights will flash once indicating that the doors are locked. The dome light will for 5 seconds upon locking the door remote. For audible confirmation the door lock, press the LOCK button a second time and the horn will beep once confirm the doors are locked.

When the UNLOCK button pressed once, the drivers door will unlock and the lights will flash twice indicating that the door unlocked. The dome light will for seconds upon unlocking the door remote. Pushing the UNLOCK button a second time within 3 seconds will unlock both doors.

Note: AUT O - ARM feature selected, the keyless entry system will automatically - arm itself seconds after the doors are unlocked with remote transmitter . Automatic - arm will cancel any door opened before the seconds timer has

Press and hold the AUX button the transmitter for second turn perimeter trailer access lights "Of (if

Press and hold the HORN button the transmitter for 3 seconds. The horn will immediately sound and running lights will flash. During panic mode, the normal function this transmitter button will suspended. LOCK and UNLOCK buttons cannot used lock and unlock the doors. T o stop the alarm, press and hold the HORN button the transmitter again for 3 seconds. the button not pressed, the alarm will automatically stop after seconds.

Battery Replacement

Under normal the transmitter battery should last approximately two When battery replacement becomes necessary , use a Panasonic 3 type Replace the battery follows: https://www.truck-manuals.net/mack/

Open the transmitter inserting a dime between the two halves the transmitter case (near the key ring hole) and

Remove the battery . Install a new battery with the positive (+) side down.

C0029325

Battery , positive (+) side down

Align the transmitter case then snap the case together https://www.truck-manuals.net/mack/

Check the operation the transmitter .

Roubleshooting

The following checks may used diagnose any problems which may arise with Remote Keyless Entry system operation. Remember check all transmitters.

Lower the turn the ignition key the OFF position and close the

Stand near the driver ’ s side door , aim the transmitter the vehicle and operate both functions the transmitter . Repeat for all transmitters, applicable.

• a single function one transmitter inoperative, replace the transmitter .

• all functions any the transmitters are reprogram all transmitters and repeat the troubleshooting Refer the the T all functions all transmitters stand approximately five feet from the vehicle (at several points around the and check the operation all transmitters each

• one transmitter cannot programmed, replace the battery the transmitter . Refer the Replacement" section.

• one transmitter does not operate some point where another transmitter does operate, replace the battery the transmitter that does not operate.

• all transmitters operate approximately five feet from the the system operating properly and repairs should attempted.

Programming the T ransmitter: T urn the ignition switch the position.

Access the keyless entry located behind the D -

Push the Program switch the keyless entry module three times. The program LED the module will solid, indicate you are now the T ransmitter Programming Mode.

Press any button one the transmitters until the horn responds with a chirp and the LED will flash confirm the first transmitter now necessary , repeat Step 3 program the 2nd, 3rd and 4th transmitters.

Note: more than four transmitters are programmed, the system will only retain the last four transmitters

T o exit Programming turn the ignition switch the OFF simply wait The LED will f confirm https://www.truck-manuals.net/mack/

Feature Programming:

T urn the ignition switch the Access the keyless entry module, located behind the DPanel.

Push the Program switch the keyless entry module six The horn will chirp six and the program LED the module will indicate you are now the Feature Programming

Press and release the transmitter button corresponding the feature you want change.

Note: The horn chirps and LED pulses will indicate the new setting.

Press the transmitter button again change the feature again. Keep pressing the transmitter button until the module advances your desired setting.

Press T ransmitter Button One Chirp/LED One Pulse Factory Default Setting T Chirps/LED T Pulses

The Remote function cannot operate with ignition

External Light turns for 3 minutes External Light turns for 5 minutes

Three Chirps/LED Three pulses = External Light turns for minutes.

AUX

Four Chirps/LED Four pulses = External Light turns for

Five Chirps/LED Five pulses = External Light turns for

T o exit Programming turn the Ignition the "Of simply wait for The horn will respond with a short + long beep and the LED turns f confirm