Komatsu 930E-4 Dump Truck Field Assembly Manual - PDF DOWNLOAD

CEAW006103

Field Assembly Manual

DUMP TRUCK SERIAL NUMBERS

A30750 - A31001

®

FOREWORD This manual is provided to aid assemblers during field assembly of the standard Komatsu 930E-4 dump truck. Variations of design required for specific truck orders may require some modification of the general procedures outlined in this manual. Follow all safety notices, warnings, and cautions provided in this book when assembling the truck.

General assembly pictures and illustrations are used in this manual. At times the illustrations may not reflect the current production truck model.

This manual lists metric (SI) and U.S. standard dimensions throughout.

All location references to “front”, “rear”, “right”, or “left”, are given in respect to the operator's normal seated position.

It is recommended that all maintenance personnel read and understand the materials in the service manual before performing maintenance and/or operational checks on the assembled truck.

FAM0013

Introduction

i

This alert symbol is used with the signal words, CAUTION, DANGER, and WARNING in this manual to alert the reader to hazards arising from improper operating and maintenance practices.

DANGER Identifies a specific potential hazard which will result in either injury or death if proper precautions are not used.

WARNING identifies a specific potential hazard which may result in either injury or death if proper precautions are not used.

CAUTION is used for general reminders of proper safety practices or to direct the reader’s attention to avoid unsafe or improper practices which may result in damage to the equipment.

ii

Introduction

FAM0013

TABLE OF CONTENTS

SUBJECT

PAGE NUMBER

FOREWORD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i

SAFETY RULES, TOOLS & EQUIPMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

TRUCK COMPONENTS AND SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

MAJOR COMPONENT WEIGHTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

FIELD WELDING FOR ASSEMBLY OR REPAIR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

RECEIVING AND ASSEMBLY PREPARATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

CHASSIS ASSEMBLY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1

DUMP BODY ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1

FINAL ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1

FINAL CHECK-OUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1

APPENDIX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1

FAM0013

Introduction

iii

NOTES

iv

Introduction

FAM0013

SAFETY RULES, TOOLS & EQUIPMENT SAFETY RULES The following list of safety practices is intended for use by personnel during field assembly of the truck.

This list of safety rules is not intended to replace local safety rules or regulations and federal, state, or local laws. The safety precautions recommended here are general and must be used in conjunction with all prevailing local rules and regulations.

1. All personnel must be properly trained for the assembly process.

2. Wear safety equipment such as safety glasses, hard toe shoes and hard hats at all times during assembly.

3. Thoroughly inspect the assembly site. Remove weeds, debris and other flammable material.

4. Use only solid, hard wood for supports. When using metal support stands, place wood blocks between the support and the frame to prevent metal to metal contact.

5. Inspect all lifting devices. Refer to the manufacturer's specifications for correct capacities and safety procedures when lifting components.

6. Perform a daily inspection of all lifting cables and chains. Replace any questionable items. Use cables and chains that are properly rated for the load to be lifted.

7. DO NOT stand beneath a suspended load. Use of guy ropes are recommended for guiding and positioning a suspended load.

Before welding, refer to Special Precautions When Servicing An AC Drive System Truck in Section 4.

10. Disconnect the battery charging alternator lead wire before welding on the frame or its components.

11. When welding, connect the ground cable to the part being welded. DO NOT allow welding current to pass through bearings, engine, etc.

12. DO NOT weld the fuel tank or hydraulic tank unless the tanks have been properly purged and ventilated.

13. Use the proper tools for the job to be performed.

Never improvise wrenches, screw drivers, sockets, etc. unless specified.

14. Lifting eyes and hooks must be fabricated from the proper materials and rated to lift the intended load.

15. When the weight of any component(s) or any assembly procedure is not known, contact your customer support manager for further information.

8. Maintain fire control equipment. Inspect fire extinguishers regularly to ensure they are fully charged and in good working condition.

9. Cap screws and/or nuts being replaced must be the same grade as originally supplied.

FAM0108 5/10

Safety Rules, Tools, & Equipment

Page 1-1

TOOLS AND EQUIPMENT FOR ASSEMBLY The following equipment is recommended for field assembly of the truck.

12. Two, ratchet pullers - 2.7 metric ton (3 ton) 1. Equipment and tool storage trailer with a lockable door. Approximately 12 x 2.5 m (40 x 8 ft) 2. Cranes a. Two, 45 metric ton (50 ton) cranes to remove the chassis from the freight trailer and place on cribbing. These cranes can also be used to lift the assembled body onto to the chassis. b. One, 109-136 metric tons (120-150 ton) crane.

The crane is needed to turn the body over after completion of the underside welding. A 45 metric ton (50 ton) crane is also required for this task.

3. One fork lift - 6804 kg (15,000 lb) capacity, with high lift capability 4. Two, 300 amp portable welding units and an oxyacetylene cutting set 5. One, propane torches for weld preheating 6. Portable air compressor - 3.5 cmm (125 cfm) and 690 kPa (100 psi) capacity.

Two, 15 m (50 ft) air hoses.

7. Metal stands and a sufficient amount of wood cribbing - sizes from 1.2 m x 30.5 cm x 30.5 cm (14 ft. x 12 in. x 12 in.) and 1.2 m x 15 cm x 15 cm (4 ft. x 6 in. x 6 in.) - such as railway cross ties

13. Two, ratchet pullers - 1.4 metric ton (1.5 ton) 14. Set of standard master mechanics hand tools

• Thread taps and dies of both inch and metric sizes

• Metric sockets and open end wrenches, 6mm to 36mm

• Inch sockets and open end wrenches up to 1 3/4 in.

• Torque wrenches - 339 N·m (250 ft lb) with 18:1 multiplier. Torque wrenches - 339 N·m (600 ft lb) with 4:1 multiplier. Hydrotorque - 1 1/2 in. drive with capability of 5559 N·m (4100 ft lb) or greater

• Box wrench 1 3/8 in. (Snap-On p/n X440B) with 12 inch extension to tighten ROPS cap screws

• Sockets: 2 1/4 in. (Snap-On P/N J15036) and 2 5/8 in. (Snap-On P/N J15042) to tighten front suspension hardware 15. Heavy duty 3/4 in. & 1 in. square drive impact wrench sets 16. Impact sockets for 3/4 in. & 1 in. square drive tools

8. Tire handler - Wiggins/Iowa Mold Tooling

17. Special tools (see list, following pages)

9. Miscellaneous air tools 10. Ladders - 3.5 m (12 ft), 2.5 m (8 ft), & 2 m (6 ft)

18. Two, hydraulic or pneumatic porta-power jacks, 4.5 and 9 metric ton (5 and 10 ton)

11. Chains, lifting cables, slings:

19. Various hooks and shackles

• • • • •

Two, 4 point slings, 3 m (10 ft) in length Two, 4 point slings, 2 m (6 ft) in length Two, 1 m (4 ft) and two, 2 m (6 ft)

20. Miscellaneous (i.e. grinders, containers, rags) 21. Spreader bars for cab and decks 22. Two ratchet hoists - 2.7 metric ton (3 ton) capacity 23. Pry bars

Two, 3 m (10 ft) nylon straps Four lengths of 2.54 cm x 15 m (1 in. x 50 ft) of rope

24. Solvent - 38 liters (10 gal) 25. Paint remover - 19 liters (5 gal) 26. Rust preventive grease 27. 22 mm Allen wrench socket - 3/4 in. drive

Page1-2

Safety Rules, Tools, & Equipment

5/10 FAM0108

LIFTING SLING GENERAL INFORMATION

FAM0108 5/10

Safety Rules, Tools, & Equipment

Page 1-3

Part Number

Description

Use

EB1759

Nitrogen Charging Kit

Suspension & Accumulator Nitrogen Charging

1. “T” Handle Valve 2. Charging Valve Adapter 3. Manifold Outlet Valves (from gauge) 4. Inlet Valve (from regulator) 5. Regulator Valve (Nitrogen Pressure) 6. Manifold 7. Charging Pressure Gauge (Suspensions) 8. Dry Nitrogen Gas

Part Number

Description

EJ2626

Roller Assembly

Use 930E-4

EH8687

930E-4SE

(No longer available as complete unit)

Power Module Removal & Installation

EJ2271

Roller Mount

930E standard

EH8681

Roller Mount

930E SE

PC0706

Bearing

TH9449

Bearing Retainer Ring

TG1680

Roller Retainer Ring

C1645

Capscrew 3/4” - 10NC x 2 1/4”

C1542

Lockwasher 3/4”

EH8686

Roller Ring

Page1-4

Safety Rules, Tools, & Equipment

5/10 FAM0108

Part Number

Description

Use

PB8326

Offset Box End Wrench, 1, 7/16 in.

Miscellaneous

Part Number

Description

Use

TZ2734

3/4 in. Torque Adapter

Miscellaneous

Part Number

Description

Use

TZ2733

Tubular Handle

Use with PB8326 & TZ2734

FAM0108 5/10

Safety Rules, Tools, & Equipment

Page 1-5

Part Number

Description

Use

BF4117

Seal Installation Tool

Front & Rear Disc Brake Floating Ring Seal Installation

ED3347

Seal Installation Tool

Rear Axle/Hub Adaptor Floating Ring Seal Installation

Part Number

Description

Use

EH4638

Sleeve Alignment Tool

Steering Linkage and Tie Rod

Part Number

Description

Use

EF9302

Wear Indicator

Brake Disc Wear

EB1723

Cap, Indicator

EF9301

Pin Indicator

WA0010

O-ring, Indicator Pin

TL3995

O-ring, Indicator Cap

EB4813

Housing, Indicator

SV9812

O-ring, housing

Page1-6

Safety Rules, Tools, & Equipment

5/10 FAM0108

Part Number

Description

Use

PC2525

Harness

Payload Meter Download

Part Number

Description

Use

EH7817

Alignment Tool

Upper Hoist Pin

Part Number

Description

Use

PB4684

Hydraulic Coupling

Miscellaneous

Part Number

Description

Use

PB9067

Bulkhead Connector

Battery Jumper

FAM0108 5/10

Safety Rules, Tools, & Equipment

Page 1-7

Part Number

Description

Use

TZ2100 TZ2727 TZ2729

Socket (1 7/8 in.)

Socket (2 1/4 in.)

Socket (1 1/4 in.)

Misc.

Part Number

Description

Use

TZ2730 TZ2731

Adapter (1-1 1/2 in.)

Adapter (3/4-1 in.)

Socket adapter

Part Number

Description

Use

WA4826

Lifting Eye Bolt

Miscellaneous

Part Number

Description

Use

PC0370

Sling

Body Retention

Part Number

Description

Use

PC0367

Shackle

Miscellaneous

Part Number

Description

Use

TR0532 TR0533

Extension (8 in.)

Extension (17 in.)

Miscellaneous

Page1-8

Safety Rules, Tools, & Equipment

5/10 FAM0108

FAM0108 5/10

Safety Rules, Tools, & Equipment

Page 1-9

Page1-10

Safety Rules, Tools, & Equipment

5/10 FAM0108

MAJOR COMPONENTS & SPECIFICATIONS TRUCK AND ENGINE

OPERATOR’S CAB

The 930E-4 Dump Truck is an off-highway, rear dump truck with AC Electric Drive. The gross vehicle weight is 498,960 kg (1,100,000 lbs). The engine is a Komatsu SSDA16V160 rated @ 2700 HP (2014 kW).

The operator cab has been engineered for operator comfort and to allow for efficient and safe operation of the truck. The cab provides wide visibility with an integral 4-post ROPS/FOPS structure and an advanced analog operator environment. It includes a tinted safety-glass windshield and power-operated side windows, a deluxe interior with a fully adjustable seat with lumbar support, a fully adjustable/tilt steering wheel, controls mounted within easy reach of the operator, and an analog instrument panel which provides the operator with all instruments and gauges which are necessary to control and/or monitor the truck's operating systems.

MAIN ALTERNATOR The diesel engine drives an in-line alternator at engine speed. The alternator produces AC current which is rectified to DC within the main control cabinet. The rectified DC power is converted back to AC by groups of devices called "inverters", which are also within the main control cabinet. Each inverter consists of six phase modules under the control of a gate driver power converter (GDPC). The two GDPCs control the operation of each phase module.

Each phase module contains paired positive and negative semiconductor switches referred to as insulated gate bipolar transistors (IGBT). The IGBTs cycle on and off at varying frequencies to create an AC power signal from the DC supply.

The AC power signal produced by each inverter is a variable-voltage, variable-frequency (VVVF) signal.

Frequency and voltage are changed to suit the operating conditions.

Cooling air for the control/power group and wheel motors, as well as the alternator itself, is provided by dual fans mounted on the alternator shaft.

AC INDUCTION TRACTION MOTORIZED WHEELS The alternator output supplies electrical energy to the two wheel motors attached to the rear axle housing.

The motorized wheels use three-phase AC induction motors with full-wave AC power.

The two wheel motors convert electrical energy back to mechanical energy through built-in gear trains within the wheel motor assembly. The direction of the wheel motors is controlled by a directional control lever located on the center console.

POWER STEERING The truck is equipped with a full time power steering system which provides positive steering control with minimum operator effort. The system includes nitrogen-charged accumulators which automatically provide emergency power if the steering hydraulic pressure is reduced below an established minimum.

DYNAMIC RETARDING The dynamic retarding is used to slow the truck during normal operation or control speed coming down a grade. The dynamic retarding ability of the electric system is controlled by the operator through the activation of the retarder pedal (or by operating a lever on the steering wheel) in the operators cab and by setting the RSC (Retarder Speed Control).

Dynamic retarding is automatically activated, if the truck speed goes to a preset overspeed setting.

BRAKE SYSTEM Service brakes at each wheel are oil-cooled multiple disc brakes applied by an all-hydraulic actuation system. Depressing the brake pedal actuates both front and rear brakes after first applying the retarder.

All wheel brakes will be applied automatically if the brake system pressure decreases below a preset minimum.

SUSPENSION ÂŽ

Hydrair II suspension cylinders located at each wheel provide a smooth and comfortable ride for the operator and dampens shock loads to the chassis during loading and operation.

FAM0212 9/09

The parking brake is a dry disc type, mounted inboard on each rear wheel motor, and is springapplied and hydraulically-released with wheel speed application protection (will not apply with truck moving).

Truck Components And Specifications

Page 2-1

Page 2-2

Truck Components And Specifications

9/09 FAM0212

SPECIFICATIONS These specifications are for the standard Komatsu 930E-4 Truck. Customer options may change this listing.

ENGINE Komatsu SSDA16V160 No. of Cylinders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 Operating Cycle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-Stroke Rated Brake HP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2700 HP (2014 kW) @ 1900 RPM Flywheel HP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2550 HP (1902 kW) @ 1900 RPM Weight (Wet)* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9608 kg (21,182 lbs) * Weight does not include Radiator, Sub-frame, or Alternator.

AC ELECTRIC DRIVE SYSTEM (AC/DC Current) Alternator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . General Electric GTA-41 Dual Impeller, In-Line Blower. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .340 mÂł/ min (12,000 cfm) Motorized Wheels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GDY106 AC Induction Traction Motors Standard Gear Ratio* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32.62:1 Maximum Speed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64.5 km/h (40 mph) * Wheel motor application depends upon GVW, haul road grade and length, rolling resistance, and other parameters.

Komatsu and GE must analyze each job condition to ensure proper application.

DYNAMIC RETARDING Electric Dynamic Retarding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Standard Maximum Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5400 HP (4026 kW) Continuous* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3300 HP (2460 kW) * Continuously rated high-density blown grids with retard at engine idle and retard in reverse propulsion.

BATTERY ELECTRIC SYSTEM Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Four 8D, 12 volt wet batteries with disconnect switch Cold Cranking Amps. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1450 CCA Alternator (S/N A30462 - A30600). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Volt, 260 Amp Output Alternator (S/N A30601 & UP). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Volt, 140 Amp Output Lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Volts Starters (2). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Volts

SERVICE CAPACITIES Crankcase (including lube oil filters) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 280 liters (74 gallons) Cooling System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 594 liters (157 gallons) Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4542 liters (1200 gallons) Hydraulic System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1325 liters (350 gallons) Wheel Motor Gear Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95 liters (25 gallons) per wheel

FAM0212 9/09

Truck Components And Specifications

Page 2-3

HYDRAULIC SYSTEMS Hoist and Brake Cooling Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tandem Gear Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 931 L/min (246 gpm) @ 1900 RPM and 17,237 kPa (2500 psi) Steering/Brake Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pressure Compensated Piston Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 246 L/min (65 gpm) @ 1900 RPM and 18,961 kPa (2750 psi) Relief Pressure - Hoist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17,237 kPa (2500 psi) Relief Pressure - Steering/Brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27,579 kPa (4000 psi) Hoist Cylinders (2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-Stage Hydraulic Tank (Vertical/Cylindrical) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Non-Pressurized Tank Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 947 liters (250 gallons) Filtration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . In-line replaceable elements Suction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Single, Full Flow, 100 Mesh Hoist and Steering Filters (Dual In-Line, High Pressure) . . . . . . . . . . . . . . . . . . . . . . . . . . . . Beta 12 Rating =200

SERVICE BRAKES All Hydraulic Actuation with Traction System Wheel Slip/Slide Control Front and Rear Oil-Cooled Multiple Discs on each wheel Total Friction Area / Brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97,019 cm² (15,038 in²) Maximum Apply Pressure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17,238 kPa (2500 psi)

STEERING Twin hydraulic cylinders with accumulator assist to provide constant rate steering Emergency power steering automatically provided by accumulators Turning Circle (SAE). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29.7 m (97 ft. 7 in.)

TIRES Radial Tires (standard) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53/80 R63 Rock Service, Deep Tread . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tubeless Rims . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . patented Phase I New Generation™ rims

STANDARD DUMP BODY CAPACITIES AND DIMENSIONS Capacity Heaped @ 2:1 (SAE). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .211 m3 (276 yd3) Struck . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .171 m3 (224 yd3) Width (Inside) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.15 m (26 ft. 9 in.)

Depth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.2 m (10 ft. 7 in.)

Loading Height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.06 m (23 ft. 2 in.)

Dumping Angle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45° NOTE: Optional capacity dump bodies are available.

Page 2-4

Truck Components And Specifications

9/09 FAM0212

WEIGHT DISTRIBUTION Empty Vehicle Front Axle (49.3%). . . . . . . 103,301 kg (227,738 lbs) Rear Axle (50.7 %) . . . . . . 107,518 kg (237,034 lbs) Total (with 50% fuel) . . . . . 210,819 kg (464,772 lbs)

Loaded Vehicle Front Axle (33.0%) . . . . . 165,554 kg (364,980 lbs) Rear Axle (67.0%) . . . . . 336,124 kg (741,020 lbs) Total . . . . . . . . . . . . . . . 501,678 kg (1,106,000 lbs)

Standard Komatsu body . . . . 30,362 kg (66,936 lbs) Standard tire weight. . . . . . . . 26,127 kg (57,600 lbs)

Nominal Payload*. . . . . . . . 290,859 kg (641,228 lbs) * Nominal payload is defined within Komatsu America Corporation’s payload policy documentation. Nominal payload must be adjusted if the weight of any customized body or tires vary from that of the standard Komatsu body and tires. Nominal payload must also be adjusted to take into account the additional weight of any custom/optional extras fitted to the truck which are not stated within the Standard Features list of the applicable specification sheet.

FAM0212 9/09

Truck Components And Specifications

Page 2-5

NOTES

Page 2-6

Truck Components And Specifications

9/09 FAM0212

MAJOR COMPONENT WEIGHTS

The condition of lifting slings, chains, and/or cables used for lifting components must be inspected before each use. Lifting equipment must be in good condition and rated for approximately two times the weight being lifted. DO NOT use worn or damaged lifting equipment. Serious injury and damage may result.

Optional equipment added onto the truck may cause an increase to the component weights listed in this chapter. Contact your customer support manager for concerns or questions about lifting truck components.

NOTE: All component weights are dry weights. The additional weight of coolant, fuel, and oil that may be in the components are not calculated into this list.

ITEM

KILOGRAMS

POUNDS

CHASSIS Wheel Rim. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2,813 . . . . . . . . . . . . . . . . . . . . . . 6,202 Tire 53/80 R63 (148" OD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4,309 . . . . . . . . . . . . . . . . . . . . . . 9,500 Rim & Tire.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7,122 . . . . . . . . . . . . . . . . . . . . . 15,702 Main Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21,874 . . . . . . . . . . . . . . . . . . . . . 48,224 Fuel Tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1,711 . . . . . . . . . . . . . . . . . . . . . . 3,772

DECK AND DECK SUPPORT COMPONENTS Cab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2,725 . . . . . . . . . . . . . . . . . . . . . . 6,008 RH Deck . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 900 . . . . . . . . . . . . . . . . . . . . . . 1,984 LH Deck . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 615 . . . . . . . . . . . . . . . . . . . . . . 1,356 Center Deck . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 250 . . . . . . . . . . . . . . . . . . . . . . . .551 LH Deck Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 654 . . . . . . . . . . . . . . . . . . . . . . 1,442 RH Deck Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 273 . . . . . . . . . . . . . . . . . . . . . . . .602 LH Upright . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 762 . . . . . . . . . . . . . . . . . . . . . . 1,680 RH Upright . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 607 . . . . . . . . . . . . . . . . . . . . . . 1,338 LH Diagonal Beam (ROPS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135 . . . . . . . . . . . . . . . . . . . . . . . .298 RH Diagonal Beam . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 . . . . . . . . . . . . . . . . . . . . . . . .150 Diagonal Ladder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180 . . . . . . . . . . . . . . . . . . . . . . . .397 Diagonal Ladder Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 . . . . . . . . . . . . . . . . . . . . . . . . 119

FAM0312 6/08

Major Component Weights

Page 3-1

ITEM

KILOGRAMS

POUNDS

POWER MODULE Air Intake Duct . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .295 . . . . . . . . . . . . . . . . . . . . . . . . 650 Engine Sub-Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1042 . . . . . . . . . . . . . . . . . . . . . . .2,297 Air Cleaner Assembly (Double) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .154 . . . . . . . . . . . . . . . . . . . . . . . . 340 Retard Grid Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2,742 . . . . . . . . . . . . . . . . . . . . . . .6,045 Electrical Control Cabinets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3,175 . . . . . . . . . . . . . . . . . . . . . . .7,000 Traction Alternator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4,037 . . . . . . . . . . . . . . . . . . . . . . .8,900 Engine (Komatsu SSDA16V160) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9608 . . . . . . . . . . . . . . . . . . . . . . 21,182 Radiator & Shroud . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1996 . . . . . . . . . . . . . . . . . . . . . . .4,400

HYDRAULIC COMPONENTS Steering Accumulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .173 . . . . . . . . . . . . . . . . . . . . . . . . 380 Hoist Cylinder w/Bushings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .969 . . . . . . . . . . . . . . . . . . . . . . .2,137 Steering Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .146 . . . . . . . . . . . . . . . . . . . . . . . . 322 Hydraulic Tank w/Covers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .590 . . . . . . . . . . . . . . . . . . . . . . .1,300

FRONT AXLE COMPONENTS Front Brake Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1,496 . . . . . . . . . . . . . . . . . . . . . . .3,298 Spindle, Hub and Brake Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4,803 . . . . . . . . . . . . . . . . . . . . . . 10,589 Steering Arm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .331 . . . . . . . . . . . . . . . . . . . . . . . . 730 Front Suspension Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2,795 . . . . . . . . . . . . . . . . . . . . . . .6,162

REAR AXLE COMPONENTS Rear Suspension Cylinder w/Bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . .907 . . . . . . . . . . . . . . . . . . . . . . .2,000 Parking Brake Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .159 . . . . . . . . . . . . . . . . . . . . . . . . 351 Pivot Eye Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .364 . . . . . . . . . . . . . . . . . . . . . . . . 802 Rear Axle Housing w/Pivot Eye . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6,561 . . . . . . . . . . . . . . . . . . . . . . 14,465 Anti-Sway Bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .148 . . . . . . . . . . . . . . . . . . . . . . . . 326 Wheel Motor & Service Brake Assembly . . . . . . . . . . . . . . . . . . . . . . . . . 18,000 . . . . . . . . . . . . . . . . . . . . . . 39,683 Wheel Ring Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .306 . . . . . . . . . . . . . . . . . . . . . . . . 675

Page 3-2

Major Component Weights

6/08 FAM0312

FIELD WELDING FOR ASSEMBLY OR REPAIR When welding on Komatsu equipment, whether at initial field assembly or during normal maintenance repairs, special procedures must be followed.

Due to the continuous program of research and development, periodic revisions may be made to this publication. It is recommended that customers contact their distributors for information on the latest revision.

The welding information contained in this chapter is general information that must be followed unless otherwise specified in a detailed repair procedure provided on an engineering drawing or a detailed specific repair procedure. Additional specific information, or detailed instructions can be obtained through your local Komatsu customer support manager.

WELD PROCEDURES Electric arc welding, either the semi-automatic “MIG” (GMAW), Flux Core (FCAW), or “Stick” electrode welding (SMAW), are approved processes for field installation and maintenance welding. Welding of highly stressed structural members such as castings, torque tubes, top and bottom plates on the frame rails, and the curved intersection points of frames should be done with the specific detailed instructions from Komatsu Product Service. See Annex A for repair procedures. These repair procedures are detailed instructions for most high stressed structural members.

APPROVED CONSUMABLES WELDER QUALIFICATION AND TRAINING

GMAW - LW102-15 or ER80S-D2

The welding technique must be of the highest standard to produce the soundest weld possible. Only welders who have been trained and qualified for structural steel welding in all positions, in conformance with the American Welding Society (AWS) D1.1 or (AWS) D14.3 only, are allowed to perform the welding. The welding instructions for field assembly of Komatsu components are normally provided by engineering drawings. Additional detailed welding instructions for field repairs are provided in the field repair manual SEB14001. A full understanding of the AWS standard welding symbols is necessary to perform and inspect such field welds. Weld sizes specified on the drawings are intended to reflect minimum requirements.

SMAW - E7018-1, E8018-C1, or E8018-C3

FCAW - E70T-5, E71T-8, or E71T8-NI1

WELD QUALITY REQUIREMENTS 1. Each weld must be homogeneous with low porosity, free from cracks, and slag inclusions.

2. Each weld must have complete fusion between the base metal and weld metal added by the electrode.

3. All welds must be reasonably smooth, without excessive deformity, and all craters filled. No cracks are permitted.

4. The toe of a weld to a stressed member must have a smooth transition. Excessive convexity in multi-pass fillet welds is not permitted. Excessive convexity produces high residual stress in the throat of the weld, and is not permitted.

5. Undercut in excess of 0.8 mm (0.03 in.) on critical welds must be reworked by the application of welding an additional cover pass. It is important that this pass is blended with the existing weld.

FAM0403

Field Welding For Assembly Or Repair

4-1

6. When welding in the vertical position, always weld using the vertical up technique. Large wash weld weaves should not be used when welding on truck frames. Properly applied multiple pass welding is the required procedure on truck frames.

2. Low Ambient Temperature - DO NOT weld in temperatures below 50°F (10°C). At low temperature conditions, preheating of all welding joint work areas is required. See preheat and post heating requirements as detailed in Annex A.

7. Slag is to be removed from all weld beads, and must be completely removed before each pass in a multiple pass procedure. It is also required that all slag is removed and tie in all areas.

Grind all welds where a weld crosses or intersects with another weld.

3. Weld Cooling - Protect the weld area from a rapid cooling rate. Heat retardation may be accomplished through the use of heat lamps, torches, insulating blankets, etc.

MATERIALS, CONTROLS, AND PRECAUTIONS The steel used in the fabrication of all Komatsu equipment is of high strength low alloy (HSLA) material of different grades. The standard dump body main plates are made from abrasion resistant materials. These materials offer themselves very well to welding during fabrication, and repair.

The welding consumables are often supplied by Komatsu America Corp. with the new equipment as part of the field welding / assembly package. For field welding and repairs, the approved consumables as detailed, should be procured from a local, reliable supplier. Other highly specialized welding consumables are available but have limited use on Komatsu structural components. Approval is required from your Komatsu customer support manager.

4. Moisture - Any moisture on the steel surfaces to be welded must be removed before welding.

Electrodes must be stored in sealed containers until needed. Electrodes must be kept in a warming oven at the work location until used to prevent any moisture absorption which might affect weld quality.

5. Foreign Materials - Any foreign substances (dirt, paint, rust, scale, and carbon deposits from cuttings) must be removed prior to welding. Clean all weld areas and surfaces with a grinder to ensure that all foreign materials have been removed.

WELD INSPECTION

Control of the welding area environment is essential for producing proper and sound welds. Essentially, five areas require attention and control.

All welding repairs are subject to inspection by a Komatsu appointed inspector or laboratory to insure quality. After the weld has been made it can be inspected by a number of non-destructive evaluation techniques. The inspections can include any of the methods listed below. All assembly welds and weld repairs that are deemed unacceptable by the inspector must be corrected at no additional cost to Komatsu. All weld repairs are also subject to additional inspection.

1. Air Movement - Avoid areas where air movement from wind, drafts, or blowers is prevalent.

This is particularly important when a shielding gas is being used as part of the welding process.

1. Visual Inspection - This is the process of looking for potential defects such as undersized welds that can be checked with weld gauges for, surface cracks, surface porosity, craters, and undercuts.

4-2

Field Welding For Assembly Or Repair

FAM0403

RECORDS 2. Dye Penetrant Inspection - This is an easily applied process which indicates cracks or surface conditions. The process is relatively inexpensive, but does not produce a permanent record except by normal photography.

3. Fluorescent Penetrant Inspection - Similar to dye penetrant inspection. This process uses a black (ultraviolet) light for increased efficiency and accuracy.

4. Magnetic Particle Inspection - This process requires special equipment that is usually more costly than the dye penetrant inspections. This process does not provide a permanent record except by normal photography.

5. Ultrasonic Inspection - This is a popular method of examining weld discontinuities. Specialized equipment and operator certification is required.

With some equipment printed data is available of the test providing a permanent record. Also, operator records with equipment settings and test results are normally recorded.

6. X-Ray Inspection - This process provides a view of the weld and base materials but it is highly specialized. This procedure provides a permanent visual record, but is more expensive than most other inspection techniques.

Komatsu requires record keeping of all welding work.

This information is valuable when personnel or job conditions change. The service and warranty departments of Komatsu must be provided with inspection reports and photographs of the weld area before, during, and after the repair. The photographs must be clear and close enough to show the weld joint preparation complete, with backer bars installed, etc. just prior to welding. These photos easily identify if the required preheating and post heating have been done with a three inch circumference around the weld repair area. Without this documentation, Komatsu will not cover any weld repair claim made under warranty. No exceptions will be made.

ANNEX A The following are general repair procedures, which must be followed for all repair and rework of major load carrying members on Komatsu equipment.

1. The repair or rework area must be protected from wind and moisture during the entire procedure. If the repair work is to done outside additional precautions must be taken to protect the weld repair process from outside elements. All welding should be done at an ambient temperature of 10°C (50°F) or above.

2. Clean and grind the entire repair area to remove all rust, grease, oils, paint, and any other foreign materials likely to contaminate the weld.

FAM0403

Field Welding For Assembly Or Repair

4-3

3. Air arc the entire crack leaving a V-shape joint.

The depth of the V (or U shaped) joint will be determined by the depth of the crack. The width to depth ratio should be approximately 1.25:1 and never less than 1:1. All cracks through the parent material will require a slightly wider root opening than the original, usually 6 mm (0.25 in.) to allow the installation of a backup strip.

Backup strips are required for all cracks that have gone through the parent material and cannot be welded from both sides. If a weld repair allows access to both sides of the plate, no backup strip is required as long as complete weld penetration is achieved. If backup strips are not used, the surface profile on both sides must be ground smooth with no undercut. Documentation must support this repair. Photographs of surface condition are required by the service and warranty departments of Komatsu.

4. Use dye penetrant to ensure the cracks are completely removed.

5. After air arcing and inspections (Steps 3 & 4) all areas cut by the air arc should be cleaned thoroughly with a grinder to remove all possible carbon deposits and dye penetrant.

6. Fill gouges with weld and grind all surfaces smooth to avoid defects in the new weld.

7. Grind all surfaces to be welded so they are free of slag, rust, and any other foreign materials.

8. Preheat the entire weld joint area until the surrounding surface area reaches 150°C (300°F) at a distance of 76 mm (3 in.) from all areas to be welded.

4-4

9. All welds are to be made with approved consumables only. The SMAW (Stick) welding rod must be used within four hours after being removed from a new sealed container or from a 52°C (125°F) minimum drying oven. Any rod that exceeds this exposure time must be dried for one hour at 427°C (800°F) before being used. Keep all weld starts and stops to a minimum.

10. When the weld is complete, immediately (before the weldment cools) post heat the entire weld area to 150°C (300°F). Even if the area is over 150°C (300°F) heat must be applied to maintain this temperature for 15 minutes, and then allow it to cool slowly. In some cases this might require wrapping with insulation blankets.

11. Grind all butt-welded repairs smooth using 36 or finer grit grinding material. All grinding marks should be parallel to the direction of primary stress if possible (and if known).

12. Hammer peen the toes of repair fillet welds as detailed in Annex B, see attached.

13. Inspect repaired areas (for surface defects) using magnetic particle or dye penetrant inspection procedures.

14. If surface defects are found, remove all defects by grinding to a maximum depth of 1.5 mm (0.06 in.). Larger defects must be removed as per the above mentioned procedures. All spot welding also requires preheating and post heating.

Field Welding For Assembly Or Repair

FAM0403

ANNEX B 2.0 TOE GRINDING WITH A ROTARY BURR

1.0 TOE HAMMER PEENING Equipment:

Equipment:

1. Hand held pneumatic hammer 2. Adequate air supply

1. High speed rotary air tool (15,000-20,000 rpm)

3. Adequate lighting

2. Tungsten carbide rotary burr 13 mm (0.50 in.) diameter with 13 mm (0.50 in.) spherical tip

4. 6 mm (0.25 in.) diameter spherical tip bit 5. Protective clothing, gloves, includes eye, face, and ear protection.

3. Adequate air supply 4. Adequate lighting 5. Protective clothing, gloves, includes eye, face, and ear protection

Procedure 1. The toe of the weld should serve as a guide for the peening tool resulting in the area of deformation being approximately equally divided between the base material and the weld metal face to the specified depth and not to exceed 5 mm (0.19 in.) in width. Refer to Figure 4-1.

Procedure

NOTE: Peening shall only be performed after weld acceptance by visual inspection.

1. The toe of the weld should serve as a guide for the burr tool resulting in the material removed being approximately equally divided between the base material and the weld metal face to the specified depth and not exceed 8 mm (0.31 in.) in width. Refer to Figure 4-2.

2. The weld must have a smooth profile and the toe must have a good transition to the parent material (no overlap) before the peening operation is performed. Grinding the weld face and toe area is permitted to correct unacceptable conditions. Visual inspection/acceptance is to be done after peening with the appropriate radius and depth gauge.

2. The weld must have a smooth profile and the toe must have a good transition to the parent material (no overlap) before the grinding operation is performed. Grinding the weld face and toe area is permitted to correct unacceptable conditions. Visual inspection/acceptance to be done after grinding with the appropriate radius and depth gauge.

3. Hold the hammer tool at approximately one half the included angle between the weld face and the parent material and perpendicular to the direction of travel. This will normally require approximately four passes of the peening tool with the pressure of near full operator weight being applied. The depth of the indentation must be between 0.6 mm to 0.8 mm (0.02 to 0.03 in.).

3. The axis of the tool should be maintained at about 45° to the parent plate and inclined at about 45° to the direction of travel. The depth of the grinding must be between 0.8 mm to 1.0 mm (0.030 to 0.040 in.). The final surface must be clean, smooth and free of all traces of undercut or slag.

FAM0403

Field Welding For Assembly Or Repair

4-5

FIGURE 4-1. TOE HAMMER PEENING

4-6

Field Welding For Assembly Or Repair

FAM0403

FIGURE 4-2. TOE GRINDING WITH A ROTARY BURR

FAM0403

Field Welding For Assembly Or Repair

4-7

BIBLIOGRAPHY American Welding Society Bulletin No. D14.3-94/ D1.1 - Specification for Welding Earthmoving and Construction Equipment Metals and How to Weld Them - James F. Lincoln Arc Welding Foundation. Cleveland, Ohio Procedure Handbook of Arc Welding - Lincoln Electric Company, Cleveland, Ohio

SPECIAL PRECAUTIONS WHEN SERVICING AN AC DRIVE SYSTEM TRUCK Consult a qualified technician, specifically trained for servicing the AC drive system, before welding on the truck.

The following procedures must be followed to ensure the safety of maintenance personnel and to help prevent damage to the equipment.

American Welding Society - Welding Handbook British Standard BS5135 - Metal Arc Welding of Carbon and Carbon-Manganese Steels Welding Steels Without Hydrogen Cracking - The Welding Institute, F. R. Coe, Author

Anytime the engine is on: • Do not open any of the cabinet doors or remove any covers.

• Do not use power cables for hand holds or foot steps.

• Do not touch retarder grid elements.

Before opening any cabinets or touching a grid element or a power cable, the engine and all warning lights must be off.

Engine Stop Procedure Prior To Maintenance Perform the following procedure prior to maintenance to ensure that no hazardous voltages are present in the AC drive system.

1. Before turning off the engine, verify the status of all the drive system warning lights on the overhead display panel. Use the lamp test switch to verify that all lamps are functioning properly.

2. If all red drive system warning lights are off, turn the engine off.

3. After the engine has been off for at least five minutes, inspect the link voltage lights. The lights are located on the exterior of the main control cabinet and back wall of the operator's cab (DID panel). If all lights are off, the retarding grids, wheel motors, alternator, and power cables connecting these devices are safe to work on.

4-8

Field Welding For Assembly Or Repair

FAM0403

Locate the GF cut-out switch in the access panel on the left side of the main control cabinet. Place the switch in the CUTOUT position.

This will prevent the alternator from re-energizing and creating system voltage until the switch is returned to its former position.

After repairs, replace all covers and doors and place the GF cutout switch and battery disconnect switches in their original positions. Reconnect all harnesses prior to starting the truck.

Leave the drive system in the rest mode until the truck is to be moved.

4. If the red lights on the exterior of the control cabinet and/or the back wall of the operator's cab continue to be illuminated, a fault has occurred.

Leave all cabinet doors in place. DO NOT touch the retard grid elements. DO NOT disconnect any power cables or use them as hand or foot holds.

Notify your Komatsu customer service manager immediately. Only qualified personnel, specifically trained for servicing the AC drive system, may perform this service.

General Welding Guidelines 1. Open the battery disconnect switches and disconnect the battery charging alternator lead wire.

2. Disconnect all electrical harnesses from the Engine Control System (ECS). The ECS is located inside the electrical cabinet behind the operator's cab. Disconnect the ground strap from the ECS. 3. Fasten the welding machine ground (-) lead to the piece being welded. The grounding clamp must be attached as near as possible to the weld area.

4. DO NOT weld on the rear of the control cabinet!

The metal panels on the back of the cabinet are part of the capacitors and cannot be heated.

5. DO NOT weld on the retard grid exhaust louvers.

6. Some power cable panels throughout the truck are made of aluminum or stainless steel. They must be repaired with the same material or the power cables may be damaged.

7. Power cables must be cleated in wood or other non-ferrous materials. DO NOT repair cable cleats by encircling the power cables with metal clamps or hardware. Inspect power cable insulation prior to servicing the cables and prior to returning the truck to service. Discard cables with broken insulation.

8. Protect power cables and wiring harnesses from weld spatter and heat.

9. DO NOT lay welding cables over or near the vehicle electrical harnesses. Welding voltage may be induced into the electrical harnesses and cause damage to components.

10. DO NOT allow welding current to pass through ball bearings, roller bearings, suspensions, or hydraulic cylinders.

FAM0403

Field Welding For Assembly Or Repair

4-9

NOTES

4-10

Field Welding For Assembly Or Repair

FAM0403

RECEIVING & ASSEMBLY PREPARATION 1. Inspect all components for possible shipping damages. Note any damage found and report to shipping agent.

2. Spread out all parts and organize per unit number. Check for missing parts. List the unit number of all major components. Verify the cab and decks are with the correct chassis.

3. Install support blocks under the chassis. The support blocks must be approximately 84 cm (33 in.) high.

5. Clean all mounting surfaces on the chassis and on the individual components.

6. Check all electrical connectors and verify they are free of paint and/or corrosion. Clean any connector with questionable electrical continuity.

7. Check all factory installed components for the proper tightening torque.

8. Arrange the work site as shown on the following page.

4. Install support blocks under the rear axle housing. The support blocks must be approximately 30 cm (12 in.) high and spread out along the axle. The support blocks must be a minimum of 51 mm (2 in.) away from the wheel motor mounting face.

FAM0503

Receiving & Assembly Preparation

Page 5-1

ASSEMBLY LAYOUT Page 5-2

Receiving & Assembly Preparation

FAM0503

CHASSIS ASSEMBLY Due to differences in machine configurations and shipping restrictions/requirements throughout the world, the shipping and packaging of large machines varies. Photographs or illustrations used in the following procedures are provided only as a general guideline. Actual assembly may be different, but this general procedure provides a basic outline for assembly.

NOTE: The hydraulic tank and accumulators may have been removed for shipping purposes and may require local installation.

Each shipment may be different, depending on the truck configuration and destination.

BASIC ASSEMBLY PROCEDURE 1. Site preparation 2. Unload truck components 3. Assemble the chassis 4. Weld the body NOTE: Chassis assembly and body welding may be done in either order, or simultaneously. The most logical order depends on available resources such as cranes, welders, assemblers, etc.

5. Static checkout (electrical & mechanical) 6. Install the body 7. Dynamic checkout (electrical & mechanical)

RECOMMENDED ASSEMBLY DATA

8. Site cleanup

1. Service Report (Pre-Delivery) 2. Acknowledgement of Receipt of Company Warranty 3. Assembly Blueprints & Schematics 4. Fluid Specifications (refer to the lubrication chart in Section 10, Appendix) 5. Suspension Oiling & Charging Procedure (available in Section 10, Appendix) 6. Fan Drive Adjustment Procedure (available in the engine service manual) 7. Toe-In Adjustment Procedure (Section 10, Appendix) 8. Hydraulic Checkout Procedure (Section 10, Appendix) 9. Brake Checkout Procedure (Section 10, Appendix) 10. Propulsion System Checkout Procedure (available in Section 10 of this manual) 11. Filter List (available in parts book) 12. Lubrication & Service PM Forms (available in the operation and maintenance manual) 13. Component Weights - for crane reference (available in Section 3 of this manual) 14. Standard Torque Chart (available in Section 10 of this manual) 15. Field Assembly Inspection Report Form (available in Section 10 of this manual)

FAM0612 6/10

Chassis Assembly

Page 6-1

ORDER OF ASSEMBLY The assembly procedure is organized in levels. Generally, the tasks to be done at a given level may be performed in any convenient order or simultaneously.

However, all tasks in that level must be completed before proceeding to the next higher level. Each level depends on the installation of components from the previous level.

NOTE: As stated earlier, shipping and packaging of large machines will vary. Some of these steps may change due to different shipping configurations and/ or truck options.

LEVEL 3 1. Spindles/Hubs 2. Steering Cylinders 3. Tie Rod

LEVEL 4 1. LH Deck 2. RH Deck/Grid Box 3. Operator Cab

LEVEL 5 1. Exhaust Pipes

LEVEL 1

2. Weld Uprights

1. Chassis - Unload and crib for assembly.

3. Blower - Air Intake Ductwork

2. Auxiliary Control Cabinet (temporary)

4. Wheel Motors

3. Deck Support (on horsecollar over suspension).

NOTE: It is easier to install and weld the deck supports before the front suspensions are installed.

However, do not install the deck supports first, unless there is a suitable means of installing the suspension with the deck support in place.

4. Rear Suspension

LEVEL 6 1. Front Tires 2. Rear Tires 3. Hoist Cylinders

LEVEL 7

5. Hydraulic Tank

1. Clearance Lights

6. Fuel Tank

2. Body Pads/Shims/Guides

7. Front Suspensions

3. Front Mud Flaps

8. Diagonal Ladder

LEVEL 8

9. Uprights/Air Cleaners 10. Diagonal Support Beams (leave loose until left deck is bolted in place)

1. Dump Body Installation

LEVEL 9 NOTE: Do not weld the air cleaner / uprights until all decks and the operator cab are installed. Ratchet hoists may be required to help tie all the structures together for a proper fit.

1. Hoist Cylinders 2. Rock Ejectors 3. Rear Mud Flaps

LEVEL 2 1. Air Cleaner Piping 2. Center Deck 3. Control Cabinet 4. Auxiliary Control Cabinet

Page 6-2

Chassis Assembly

6/10 FAM0612

CHASSIS ASSEMBLY The photographs referenced in this procedure depict an actual truck assembly. Assembly at another location may be different. However, this outline will provide a general basis for assembly.

LEVEL 10 1. Clean the Truck 2. Decals 3. Lighting Wiring 4. Charge Suspensions 5. Charge Accumulators 6. Add Fluids 7. Charge the Air Conditioning System NOTE: Prior to starting the engine, verify that the steering pump case is full of oil.

LEVEL 11 1. System Checkouts

Follow all safety recommendations in this manual. Follow all local, state, and federal regulations.

In the procedures that follow, many very heavy components will be required to be lifted into place and secured.

2. Exhaust Blankets 3. Clean Assembly Rear 4. Touch Up Paint 5. Train Operators 6. Optional - Install Fire Suppression System • Inspect all lifting devices. Slings, chains, and cables used for lifting components must be inspected daily for serviceable condition.

Refer to the manufacturer’s guidelines for correct capacities and safety procedures when lifting components. Replace any questionable items.

• Slings, chains and cables used for lifting must be rated for approximately two times the intended load.

• When in doubt as to the weight of components or any assembly procedure, contact your customer support manager for further information.

• Lifting eyes and hooks must be fabricated from the proper materials and rated to lift the intended load.

• Never stand beneath a suspended load. Guy ropes are recommended for guiding and positioning a suspended load.

• Before lifting, ensure there is adequate clearance from overhead structures or electric power lines.

FAM0612 6/10

Chassis Assembly

Page 6-3

GENERAL PRECAUTIONS AND INSTRUCTION 1. Clean and remove all foreign material from component mounting surfaces.

Disconnect the battery cables before welding on the truck. Failure to do so may seriously damage the batteries and electrical equipment. Disconnect the battery charging alternator lead wire before welding on the frame or its components.

2. Mount the front suspensions first so that deck substructures can be installed while other components are installed.

Fasten the welding machine ground cable to the component being welded.

4. Install the fuel return hose on the rearward most fitting on the fuel tank.

DO NOT allow welding current to pass through bearings.

5. Torque the deck mounting bolts before the exhaust tubes, etc. are installed.

DO NOT lay welding cables over truck electrical cables and harnesses. Welding voltages could be induced into the truck wiring and cause damage to components.

6. Verify all electrical connectors are free from paint and/or corrosion. Clean any connector that may be questionable.

DO NOT weld on the fuel tank or the hydraulic tank unless they have been properly purged and ventilated.

Maintain fire control equipment. Inspect fire extinguishers regularly to ensure they are fully charged and in good working condition.

3. DO NOT weld the front uprights until all upper decks are installed.

7. Do not torque the diagonal ROPS beam until after the operator cab and LH air intake tubes are in place.

8. Before installing the cab to the substructure, tap all threaded holes to remove paint.

9. Verify all wiring is properly connected before attempting to start the engine.

10. Recheck the torque on hardware installed at the factory.

HARDWARE TIGHTENING METHOD

Mark cap screws and nuts with paint or ink before tightening to the specified torque. This method provides verification that the hardware has been properly tightened.

1. Snug down all of the hardware with an impact wrench or appropriate ratchet.

2. Apply a paint mark down the side of the hardware and onto the component surface. Make sure that all of the hardware that is being tightened is marked.

3. Apply the specified torque to all of the marked hardware.

All of the marks should now be offset, showing that the hardware has been properly tightened.

Page 6-4

11. Use blocks for charging the suspension (oil & nitrogen). Follow the procedures outlined in Section 10, Appendix.

12. Steering accumulators are normally not charged with nitrogen when shipped from the factory.

Use proper precautions when checking the nitrogen pressure and oil level in the cylinder.

13. Brake accumulators are normally charged with nitrogen when shipped from the factory. Use proper precautions when checking pressures.

14. Verify the lube system is lubricated, purged and all levels full prior to start up.

15. Purge air from the steering pump before truck operation. Pressure will not build in the brake and steering circuit if air is present. Air in the system may damage the pump. Refer to the Hydraulic Checkout Procedure in Section 10 of this manual.

16. Use the battery disconnect switch when arc welding. Connect the weld ground near the weld area.

Chassis Assembly

6/10 FAM0612

To help prevent contamination that may lead to premature pump failures, flush the hydraulic system before the initial truck start-up.

17. Before the truck is started for the first time, the hydraulic system must be flushed. Refer to the following hydraulic system flushing procedure.

HYDRAULIC SYSTEM FLUSHING PROCEDURE When a new truck is assembled and the engine is started for the very first time, the hydraulic system must be flushed immediately to remove contamination that may have been introduced during the field assembly process. DO NOT start the engine unless all flushing equipment is installed and ready for use.

The flushing procedure will help eliminate harmful contamination that may lead to premature pump or valve failures. Starting the engine just one time without performing the flushing procedure may contaminate the hydraulic system.

Special hydraulic system flushing tools for the 930E truck have been released. Hoist system bypass blocks (PC3074) and steering system flushing hose (XB5777) must be on-site before or during field assembly, so when the truck is started for the first time, the hydraulic system can be flushed and any debris can be removed from the hydraulic system.

Fitting assembly (XB7075) shown as (3, Figure 6-7) will also be required.

All flushing hoses must be rated to withstand 27 580 kPa (4,000 psi) pressure. The hoses must be 1 inch inside diameter and meet SAE 100R12 specifications.

Hydraulic fluid escaping under pressure can have sufficient force to enter a person's body by penetrating the skin and cause serious injury, and possibly death, if proper medical treatment by a physician familiar with this type of injury is not received immediately.

Before disconnecting pressure lines, removing fittings or replacing components in the hydraulic circuits, or installing test gauges, ALWAYS bleed down the steering and brake accumulators.

NOTE: The hoist cylinder bypass blocks should be saved for possible use later in case the hydraulic system needs to be flushed after a component failure.

1. If the tires are installed on the truck, chock the left and right rear wheels securely on both sides to prevent truck movement. If the truck is sitting on cribbing, ensure it is secure enough to allow safe operation of the engine and clearance for turning the front spindles lock to lock without risk of collapsing the cribbing.

2. Inspect all hydraulic hoses to ensure that they are properly routed and securely connected.

3. Connect a laptop PC to the interface module.

Start the Interface Realtime Data Monitor program.

4. Ensure that both brake accumulators and both steering accumulators are properly precharged with nitrogen to 9 650 kPa (1,400 psi). Refer to the shop manual for the accumulator charging procedure.

5. Confirm that the steering pressure is released by turning the steering wheel. No steering movement should occur.

6. If any fault codes are displayed, troubleshoot the system and repair the problem before proceeding.

Table 1: XB5777 HOSE ASSEMBLY Part Number

Qty

HA2185

1

Hose

WB0546

1

Fitting, Elbow - 45 Deg

WB0599

1

Fitting, Straight Adapter

FAM0612 6/10

Description

Chassis Assembly

Page 6-5

7. Install accurate pressure gauges at the following locations: • Pressure test port “TP3” (4, Figure 6-1) on the bleed down manifold - 35 000 kPa (5,000 psi).

• Pressure test port (1, Figure 6-2) for the front brake cooling circuit - 3 450 kPa (500 psi).

• Pressure test ports (2, Figure 6-2) on both high pressure hoist filters - 24 000 kPa (3,500 psi).

• Pressure test port (1, Figure 6-3) for the rear brake cooling circuits - 3 450 kPa (500 psi).

• Pressure test port “GPA” (2, Figure 6-4) located on the steering pump - 35 000 kPa (5,000 psi).

.

If any hydraulic pressure is detected on the pressure gauge installed at TP3, there is residual oil pressure in the system. Do not loosen or remove any hydraulic hoses, fittings or components. The steering accumulators have not been properly depressurized. Locate and correct the depressurization problem. Always relieve all hydraulic pressure before disconnecting any hydraulic lines or fittings. Always tighten all connections securely before applying pressure. Confirm that the steering pressure is released by turning the steering wheel. No steering movement should occur.

8. Ensure pressure gauge connected at "TP3" reads 0 kPa (0 psi) before removing plugs (1 & 2, Figure 6-1). Remove plugs (1 & 2) from the bleed down manifold. Connect jumper hose assembly (XB5777) between "QD supply" port and the "QD return" port on the bleed down manifold. Tighten all connections securely before applying pressure.

FIGURE 6-1. BLEED DOWN MANIFOLD 1. Plug - QD Supply Port 4. Test Port (TP3) 2. Plug - QD Return Port 5. Test Port (TP2) 3. Bleed Down Manifold

9. Connect the four hoist cylinder hoses (3, Figure 6-2) together as shown using bypass blocks (4).

The hardware for connecting the hoses to the blocks is the same hardware for connecting the hoses to the hoist cylinders. Ensure that all of the connections are secure. Cover all open ports to prevent contamination.

FAM0612 6/10

Chassis Assembly

Page 6-6

10. At the rear axle housing, connect brake cooling lines (1, 2 & 3, Figure 6-5) together using fitting assembly (3, Figure 6-6). Cap the three open fittings on the axle housing with clean caps.

Several hose clamps may have to be removed to connect the three hoses to the fitting assembly.

11. At the left front brake assembly, connect cooling hoses (1 & 3, Figure 6-7) together using adapter (2). Cap the open fittings on the brake assembly. At the right front brake assembly, connect the two cooling hoses together using another adapter. Cap the open fittings on the brake assembly.

NOTE: The adapters are installed on the truck when it is shipped from the factory.

FIGURE 6-3. BRAKE COOLING MANIFOLD 1. Test Port (Rear Brake Cooling Pressure) 2. Test Port (Front Brake Supply Pressure) 3. Test Port (Front Brake Return Pressure) 4. Test Port (Hoist Return Pressure) 5. Test Port (Rear Brake Return Pressure)

FIGURE 6-2. TEST PORT LOCATIONS AND HOIST FLUSHING HOOKUP 1. Test Port (Front Brake Cooling Circuit) 2. Test Port (Hoist Filters) 3. Hoist Cylinder Hoses 4. Bypass Blocks (PC3074)

FAM0612 6/10

Chassis Assembly

Page 6-7

12. The steering pump case must be filled with oil before startup to avoid pump damage. Disconnect the hose that is connected to fitting (1, Figure 6-4). Then remove fitting (1). Fill the steering pump case with clean type C-4 hydraulic oil through the case drain port. It may require up to 2.9 liters (3 quarts) of oil. Re-install fitting (1) and reconnect the hose.

NOTE: Filling the steering pump case with oil does not eliminate the need to bleed air from the pump suction line.

FIGURE 6-5. REAR AXLE BRAKE LINES 1. BS - Left & Right Brake Cooling Oil Supply 2. LBR - Left Brake Cooling Return Line 3. RBR - Right Brake Cooling Return Line

FIGURE 6-4. STEERING PUMP & HOIST SYSTEM QUICK DISCONNECTS 1. Fitting (Pump Case Drain) 2. Test Port (GPA)

FIGURE 6-6. FITTING ASSEMBLY 1. 90° Swivel Elbow (PC3062) 2. T-Fitting (WB0426) 3. Fitting Assembly (XB7075)

Page 6-8

Chassis Assembly

6/10 FAM0612

Do not apply the brakes or turn the steering wheel at any time during this procedure until Step 33.

17. Ensure both brake accumulator bleed down valves (1, Figure 6-8) are open.

18. Move the hoist control lever to the FLOAT position.

FIGURE 6-7. FRONT WHEEL BRAKE LINES 1. Cooling Hose 2. Adapter (EG1794)

3. Cooling Hose 4. Brake Apply Hose

19. Turn the key switch ON but do not start the engine. Verify that the low steering accumulator precharge warning is not displayed. If the warning is displayed, correct the problem before proceeding.

13. Fully open all hydraulic shutoff valves in the pump suction lines. The valves are fully open when the valve handle is in-line with the hose.

Serious pump damage will occur if any shutoff valve is not fully open when the engine is started.

14. Fill the hydraulic tank with clean type C-4 hydraulic oil. Ensure that the oil level is visible in the center of the upper sight glass.

FIGURE 6-8. BRAKE MANIFOLD 1. Accumulator Bleed Down Valves 2. Brake Manifold

15. To bleed trapped air from inside the pump suction hoses, loosen the cap screws where the three suction hoses attach to the inlet of each pump. Ensure that the O-ring does not fall out of the groove. After oil appears, retighten the cap screws to the standard torque.

16. Check the hydraulic tank oil level. If necessary, add oil.

FAM0612 6/10

Chassis Assembly

Page 6-9

20. Start the engine and operate at low idle. Within 30 seconds after starting the engine, check the two oil pressures listed below. If the oil pressure readings are not correct, stop the engine.

Locate and repair the problem before proceeding. If the pressure readings are correct, proceed to the next step. Do not turn the steering wheel or apply the brakes at this time.

• With the engine at low idle, and the oil temp at 21° C (70° F), oil pressure at the hoist filters should be approximately 552 kPa (80 psi) or less.

22. If all pump pressures and brake cooling oil supply pressures are correct as stated in Steps 20 and 21, increase engine speed to 1500 rpm and flush the system for 20 minutes. During this time, move the hoist control lever to the POWER UP position for 30 seconds, and then move it to the POWER DOWN position for 30 seconds. Repeat this hoist control cycle five times. This process will carry any system contaminants to the hydraulic filters.

Monitor the pressure gauges at the front and rear brake cooling test ports during this step.

The pressure readings should always be 0 kPa (0 psi) when the hoist valve is in the POWER UP or POWER DOWN positions, and approximately 345 kPa (50 psi) while in the HOLD or FLOAT positions.

• Oil pressure at steering pump test port "GPA" should be approximately 690 kPa (100 psi).

Do not operate the engine at low idle for more than 30 seconds. The steering pump pressure at test port "GPA" must be at or above 1 725 kPa (250 psi) during the flushing process to provide adequate internal pump lubrication. Steering pump damage will result if the pressure is below 1 725 kPa (250 psi) for more than 30 seconds.

21. If the oil pressure readings in Step 20 are correct, increase the engine speed to obtain oil pressure at test port "GPA" of 1 725 kPa (250 psi). Move the hoist control lever to the POWER UP or to the POWER DOWN position. The pressure readings at the front brake cooling port (1, Figure 6-2) and rear brake cooling test port (1, Figure 6-3) should be 0 kPa (0 psi). If the pressure is not 0 kPa (0 psi), the hoist valve piping (or pilot lines) may be connected incorrectly, or the hoist valve could be defective. Correct the plumbing problem or replace the hoist valve and repeat this step.

23. When the 20 minute flushing process is complete, turn the key switch to the OFF position and allow at least two minutes after the engine has stopped for the steering accumulators to completely depressurize.

24. Remove the adapters from both front wheel brake cooling hoses and re-connect the cooling hoses to the front brake assemblies.

25. Remove the tee fitting assembly from the three rear brake cooling hoses. Re-connect the three rear brake cooling hoses to the axle housing.

26. Check the pressure gauge connected to the "TP3" port on the bleed down manifold. If any pressure is still in the system, the bleed down process did not complete. Locate and repair the problem. If the pressure is 0 kPa (0 psi), remove the jumper hose and fittings installed in the bleed down manifold. Install the two plugs (1 & 2, Figure 6-1) previously removed back into the bleed down manifold.

27. Check the hydraulic tank oil level. If necessary, add oil.

28. Close both brake accumulator bleed down valves (1, Figure 6-8).

Page 6-10

Chassis Assembly

6/10 FAM0612

NOTE: Do not combine Step 29 with any other steps.

Do not apply the brakes or steer the truck during Step 29.

29. To flush the accumulators, start the engine and operate the engine until the pressure at the "TP3" port on the bleed down manifold is approximately 21 200 kPa (3,075 psi). This is the pressure where the steering pump unloader valve shifts and unloads the pump.

• If the accumulator pressure exceeds 21 546 kPa (3,125 psi), immediately turn the engine off and open the brake accumulator bleed down valves.

Refer to Steering pump pressure control adjustments in the shop manual, then repeat Step 29.

• If the accumulator pressure does not reach 20 856 kPa (3,025 psi), check for faults on the Interface Realtime Data Monitor program. If there is a bleed down fault active, locate and correct the problem. If no faults are active, refer to Steering pump pressure control adjustments in the shop manual, then repeat Step 29.

30. When the pressure gauge connected to "TP3" reads approximately 21 200 kPa (3,075 psi):

31. If Step 30-b results are satisfactory, open both brake accumulator bleed down valves (1, Figure 6-8) on the brake manifold to completely depressurize the brake accumulators. After all hydraulic pressure has been released, close both accumulator bleed down valves. Repeat Steps 29 - 31 five times.

32. To flush the steering system, start the engine.

Allow the accumulators to fully charge and the steering pump to unload.

33. Turn the steering wheel full left and then full right ten times.

34. Turn the key switch to the OFF position. Allow at least two minutes after the engine has stopped for the steering accumulators to completely depressurize. The pressure gauge at the bleed down manifold pressure test port "TP3" will be 103 kPa (15 psi) or less after a successful bleed down.

35. The hydraulic system flushing procedure has been completed. All hydraulic system high pressure filter elements must be replaced. a. Close both hoist pump suction line shutoff valves and the steering pump suction line shutoff valve.

a. For the first time only through this step: • Leave the key switch in the ON position, and use the engine shut down switch on the center console to stop the engine.

• After the engine has stopped, confirm that steering accumulator bleed down does not occur, and that no bleed down faults or any other faults are displayed on the Interface Realtime Data Monitor. b. The second and subsequent times through this step: • Turn the key switch to the OFF position.

Confirm that after the engine has stopped that the steering accumulator bleed down process begins.

• Confirm that accumulator bleed down completes within two minutes. Also confirm that bleed down fault A236 "Steering bleed fault" or any other bleed down fault does not become active. The pressure gauge at the bleed down manifold pressure test port "TP3" will be 103 kPa (15 psi) or less after a successful bleed down.

FAM0612 6/10

b. Remove the hoist and steering hydraulic filter elements. Clean the housings and install new filter elements. c. Open both hoist pump suction line shutoff valves and the steering pump suction line shutoff valve.

36. Remove all pressure gauges and re-install the dust caps on all quick disconnect fittings.

37. Check the hydraulic tank oil level. If necessary, add oil.

38. Proceed to the steering and brake system checkout procedures in the Field Assembly Manual.

39. After the steering and brake system checkout procedures are completed, remove hoist cylinder bypass blocks (4, Figure 6-2) and connect the hoist cylinder hoses to the hoist cylinders.

Ensure the hoses and ports are clean to prevent contamination.

NOTE: Do not to extend the hoist cylinders until the body is installed.

Chassis Assembly

Page 6-11

FIGURE 6-9.

1. Lift the chassis off the truck/trailer (Figure 6-9) or rail car using two cranes with a minimum capacity of 50 tons each.

FIGURE 6-10.

2. Place the chassis on adequate support blocks in a level position. The weight of the chassis, as shipped, is approximately 60 382 kg (133,000 lbs).The support blocks must be approximately 84 cm (33 in.) high at the front, and approximately 30 cm (12 in.) high under the rear axle housing (Figure 6-10). Placement of the chassis at this height will allow easy installation of the truck components.

3. Thoroughly clean the chassis.

Page 6-12

Chassis Assembly

6/10 FAM0612

DO NOT mix components from different trucks. Components such as deck supports are marked with the serial number of the corresponding truck unit. Only use components of the unit number that is being assembled.

FIGURE 6-11.

4. Lift the LH deck support into position. The weight of the LH deck support is approximately 654 kg (1442 lbs).

Bolt the support into place. Do not weld the support at this time.

Refer to Figure 6-11.

FAM0612 6/10

Chassis Assembly

Page 6-13

FIGURE 6-12.

5. Lift the LH upright into position and install the four cap screws. Tighten to 465 ± 47 N·m (343 ± 34 ft lb). The weight of the LH upright with air cleaners is approximately 930 kg (2,050 lb).

Refer to Figure 6-12.

NOTE: DO NOT weld the torque tubes on the uprights until the decks are installed.

Page 6-14

Chassis Assembly

6/10 FAM0612

FIGURE 6-13.

6. Lift the LH diagonal beam into position and install the capscrews loosely. The weight of the beam is approximately 135 kg (298 lb).

Refer to Figure 6-13.

NOTE: Do not tighten the cap screws until the deck and the cab are in place.

FAM0612 6/10

Chassis Assembly

Page 6-15

FIGURE 6-14. DETERMINING CAB FIT 1. Cab 2. Deck Support

3. LH Diagonal Beam 4. Left Upright

7. Lift the cab onto the deck supports and install the mounting hardware. Verify no gaps exist between the mounting pads of the cab. If gaps are present, the upright and/or deck support may need to be repositioned.

8. Tighten the cap screws that secure the LH diagonal beam.

Page 6-16

Chassis Assembly

6/10 FAM0612

FIGURE 6-15.

9. Tack weld the LH deck support.

If the tapped pads are not removed, a complete weld around the support can not be achieved. The gaps in the weld around the support may result in premature frame cracking in this area.

10. Remove the four tapped pads on each support and the corresponding blocks on the horsecollar to allow for a complete weld around the joint.

11. Remove the plate and backer strip from the back of the LH deck support (see inset in Figure 6-16). Install the backer strip at the end of the deck support. Install the plate at the end of the deck support.

12. Weld completely around the support without leaving any gaps. Finish welding around the plate.

13. Grind all areas, and clean. Paint after welding is complete.

Refer to Figures 6-16 through 6-19.

14. Lift the RH deck support into position. The weight of the RH deck support is approximately 273 kg (602 lb).

Bolt the support into place.

15. Repeat Steps 9 through 13 for the RH deck support.

FAM0612 6/10

Chassis Assembly

Page 6-17

FIGURE 6-16.

FIGURE 6-17.

Page 6-18

Chassis Assembly

6/10 FAM0612

FIGURE 6-18.

FIGURE 6-19.

FAM0612 6/10

Chassis Assembly

Page 6-19

FIGURE 6-20.

16. Weld the LH upright to the front frame tube according to the drawing specifications provided with the truck.

Refer to Figure 6-20.

17. Remove the cab after welding is complete. Continue with the assembly process.

Page 6-20

Chassis Assembly

6/10 FAM0612

Rear Suspension Installation 18. Secure rear suspension assembly (1, Figure 6-21) to a fork lift and raise it into position. The suspension assembly should be retracted as far as possible before installation.

19. Position the top suspension eye between the ears on the frame. Orient the cylinder so that the charging valve faces the opposite suspension cylinder.

20. Lubricate all pin-to-bearing and pin-to-sleeve contact surfaces with anti-seize compound. Lubricating the pin surfaces aids in removal and installation, as well as prevention of rust and corrosion.

21. Align the hole in pin (5) with the hole in the mounting bore. Drive in the pin far enough so that the pin does not fall out.

22. Insert bearing spacer (7) over the pin. Continue to drive the pin through spherical bearing (9). When the pin emerges, insert the remaining bearing spacer over the pin on the opposite side and continue to drive the pin until the hole in the axle housing is aligned with the hole in the pin.

23. Install shoulder bolt (2), then install washer (3) and nut (4). If further alignment of the holes is necessary, install a pin removal tool onto the pin. Use the tool and a large pipe wrench or other suitable device to align the holes. Tighten the nut to 68 N¡m (50 ft lb).

24. Adjust the piston rod height until the lower suspension eye is aligned with the bore in the rear axle housing.

Repeat the above procedure to install the bottom pin. Mounting components in the top and bottom joints are identical.

FIGURE 6-21. REAR SUSPENSION CYLINDER PIN INSTALLATION 1. Suspension Cylinder 2. Shoulder Bolt 3. Flat Washer 4. Locknut

FAM0612 6/10

5. Pin 6. Sleeve 7. Spacer 8. Retaining Ring

Chassis Assembly

9. Bearing 10.Capscrew 11.Lockwasher

Page 6-21

FIGURE 6-22.

25. Clean the mounts for the fuel tank.

26. Lift the tank into position (Figure 6-22). The weight of the fuel tank is approximately 1 711 kg (3,772 lb). a. Install the mounting caps, washers and cap screws at the top of the fuel tank. Do not tighten the cap screws at this time. b. Install the rubber dampeners, flat washers and cap screws in the lower mounts at the rear of the fuel tank.

Tighten the cap screws to 420 ± 42 N·m (310 ± 31 ft lb). c. Tighten the cap screws at the top of the fuel tank to 711 ± 72 N·m (525 ± 53 ft lb).

Page 6-22

Chassis Assembly

6/10 FAM0612

FIGURE 6-23.

27. Clean the mounts for the hydraulic tank.

28. Lift the tank into position. Refer to Figure 6-23. The weight of the hydraulic tank is approximately 590 kg (1,300 lb). a. Install the four mounting cap screws near the top of the tank. Tighten to 622 ± 62 N·m (459 ± 46 ft lb). b. Install the two mounting cap screws near the bottom of the tank. Tighten to 800 ± 80 N·m (590 ± 59 ft lb).

FAM0612 6/10

Chassis Assembly

Page 6-23

FIGURE 6-24.

29. Connect the piping to the hydraulic tank and properly tighten all fittings. Refer to Figure 6-24.

FIGURE 6-25.

30. Install the fuel tank quick fill box at the bottom of the hydraulic tank. Refer to Figure 6-25

NOTE: When the machine is ready for operation, the hydraulic tank shut-off valves must be opened. The valves are open when the handles are parallel with the hoses.

Page 6-24

Chassis Assembly

6/10 FAM0612

FIGURE 6-26.

31. Install the two hoist filters onto the bracket at the inner side of the fuel tank. Connect the fuel supply and return lines to the fuel tank.

Refer to Figure 6-26.

FAM0612 6/10

Chassis Assembly

Page 6-25

32. Raise the hoist cylinder into position over the pivot point on the frame. The weight of each hoist cylinder is approximately 969 kg (2,137 lb). Position the cylinder with the air bleed vent plug on top, and facing the front of the truck. Refer to Figure 6-27.

33. Install spacer (6, Figure 6-28). Align the bearing eye with the pivot point and push the cylinder into place.

34. Install retaining plate (3), locking plate (2), and cap screws (1). Tighten the cap screws to 298 N¡m (220 ft lb).

Bend the locking plate tabs over the cap screw flats.

FIGURE 6-27.

FIGURE 6-28.

1. Cap Screw 2. Locking Plate 3. Retaining Plate

Page 6-26

Chassis Assembly

4. Retainer Ring 5. Bearing 6. Spacer

6/10 FAM0612

Front Suspension Installation

FIGURE 6-29.

FIGURE 6-30.

35. Remove all paint, rust, dirt and foreign debris from the suspension mounting surfaces. Refer to Figures 6-29 and 6-30.

36. Clean and dry the mounting surfaces on both the suspension and the frame. Use a cleaning agent that does not leave a film after evaporation, such as isopropyl alcohol, acetone or lacquer thinner.

37. Inspect the suspension and frame mounting surfaces for damage or wear. Check for the following criteria: Flatness of each surface must be within 0.25 mm (0.010 in.).

Surface finish must not exceed 0.635 µm (250 µ in.) roughness average (RA), medium tool cut.

If measurements are not within specifications, contact your Komatsu customer service manager for further instructions.

38. Clean and dry all suspension mounting hardware. Use the same cleaning agent that was used to clean the mounting surfaces.

FAM0612 6/10

Chassis Assembly

Page 6-27

High tightening torque is required to load the front suspension mounting cap screws. Repeated tightening will result in cap screw fatigue and damage. DO NOT reuse mounting cap screws, washers and nuts.

Replace the hardware after each use.

Suspension mounting cap screws are specially hardened to meet or exceed grade 8 specifications.

Replace only with cap screws of correct hardness. Refer to the appropriate parts book for the correct part numbers.

The use of dry threads in this application is not recommended. Due to the high tightening forces required to load these cap screws, dry threads or threads lubricated with anti-seize compounds may result in damage. Only use the approved lubricant specified below.

39. Lubricate the cap screw threads, cap screw head seats, washer faces and nut seats with 5% molybdenumdisulphide grease.

40. Identify and separate the hardware according to location on the suspension. Refer to Figure 6-31.

FIGURE 6-31.

1. Cap Screw - 1 1/2" - 6NC x 6 1/2" (G8) 2. Flat Washer - 1 1/2" (G8) 3. Nut - 1 1/2" - 6NC (G8) 4. Cap Screw - 1 3/4" - 5NC x 14 1/2" (G8) 5. Flat Washer - 1 3/4" (G8) 6. Nut - 1 3/4" - 5NC (G8) 7. Spacer 8. Shear Key 9. Part Of Frame

Page 6-28

Chassis Assembly

6/10 FAM0612

41. Lift the front suspension into position on the frame.

The weight of each front suspension cylinder is approximately 2795 kg (6162 lb). Refer to Figure 632.

FIGURE 6-32.

FAM0612 6/10

Chassis Assembly

Page 6-29

42. Install the mounting hardware and the shear key.

Install the shear key flush with the side face of the suspension. Refer to Figure 6-33.

a. Install one washer under each cap screw head and one washer under each nut (where applicable).

b. Initially tighten the hardware to 1356 ± 136 N·m (1000 ± 100 lb ft) in the sequence shown in Figure 6-34. Use a properly calibrated torque wrench to ensure accuracy.

NOTE: Do not exceed 4 rpm tightening speed. Do not hammer or jerk the wrench while tightening.

FIGURE 6-33. c. The mounting cap screws will now need to be loosened and then tightened using angleadvance. The first set of cap screws to be adjusted will be at the upper mounting joint. The cap screws must be loosened one at time and then tightened by advancing a specified rotational degree. Use the map shown in Figure 6-34 for proper tightening sequence.

FIGURE 6-34.

Page 6-30

Chassis Assembly

6/10 FAM0612

Upper Mounting Joint - 60° Advance The proper sequence for the upper mounting joint is 1-2-3-4-9-10. Refer to Figure 6-34.

43. Loosen the first cap screw. All other cap screws must be maintained at 1356 ± 136 N·m (1000 ± 100 lb ft).

44. Tighten the cap screw to 95 N·m (70 lb ft).

NOTE: Do not exceed 4 rpm tightening speed. Do not hammer or jerk the wrench while tightening.

45. Mark a corner of the cap screw head with a paint marker as shown in Figure 6-35. Draw a reference line on the suspension surface next to the marked corner on the cap screw. Draw a reference line on the suspension 60 degrees in advance of the marked corner on the cap screw.

46. Advance the cap screw to the 60° advance mark.

Hold the nut at the rear of the joint stationary while tightening.

FIGURE 6-35.

47. Make new reference lines along the cap screw, nut and frame at the rear of the joint as shown in Figure 6-36. These reference lines will be used to verify the cap screws have maintained their torque.

48. Repeat this process in sequence for the remaining cap screws in the upper mounting joint.

NOTE: If for any reason these fasteners need to be checked for tightness after completing this procedure, loosen and inspect all 14 cap screws and repeat the entire process. The hardware, again, must be cleaned and lubricated before repeating.

FIGURE 6-36.

FAM0612 6/10

Chassis Assembly

Page 6-31

Lower Mounting Joint - 120° Advance The proper sequence for the lower mounting joint is 5-6-7-8-11-12-13-14. Refer to Figure 6-34.

49. Loosen the first cap screw. All other cap screws must remain tightened.

50. Tighten the cap screw to the specified torque: Cap screws 5-6-7-8 . . . . . . 136 N·m (100 lb ft) Cap screws 11-12-13-1 . . . 4271 N·m (200 lb ft)

NOTE: Do not exceed 4 rpm tightening speed. Do not hammer or jerk the wrench while tightening.

51. Mark a corner of the cap screw head with a paint marker as shown in Figure 6-37. Draw a reference line on the suspension surface (or frame) next to the marked corner on the cap screw. Draw a reference line on the suspension surface (or frame) 120 degrees in advance of the marked corner on the cap screw.

52. Advance the cap screw to the 120° advance mark.

Hold the nut at the rear of the joint (where applicable) stationary while tightening.

FIGURE 6-37.

53. Make new reference lines along the cap screw, nut and frame at the rear of the joint as shown in Figure 6-36. For the four cap screws with spacers, refer to Figure 6-38. These reference lines will be used to verify the cap screws have maintained their torque.

54. Repeat this process in sequence for the remaining cap screws in the lower mounting joint.

NOTE: If for any reason these fasteners need to be checked for tightness after completing this procedure, loosen and inspect all 14 cap screws and repeat the entire process. The hardware, again, must be cleaned and lubricated before repeating.

Page 6-32

Chassis Assembly

FIGURE 6-38.

6/10 FAM0612

FIGURE 6-39.

55. Clean the tapered portion of the suspension rod and the bore of the spindle. Lubricate the two surfaces with multi purpose grease number 2 (5% molybdenum disulphide).

56. Lift the spindle/brake assembly into position. The weight of each spindle/brake assembly is approximately 4 803 kg (10,589 lb). Refer to Figure 6-39.

NOTE: A ratchet hoist may be used at the lower portion of the steering arm to the lifting hook to aid in leveling the assembly for easier mounting to the suspension.

FAM0612 6/10

Chassis Assembly

Page 6-33

FIGURE 6-40.

57. Lift the retainer plates to the bottom of each suspension using blocks and a hydraulic jack. Refer to Figure 640.

Page 6-34

Chassis Assembly

6/10 FAM0612

FIGURE 6-41.

58. Lubricate the 14 cap screws on the threads and seats with lithium based chassis grease (multi-purpose, EP NLGI).

59. Install the cap screws. Evenly tighten the cap screws to 678 N·m (500 ft lb). Continue to tighten the cap screws in increments of 339 N·m (250 ft lb) until the final torque of 2 705 ± 135 N·m (1,995 ± 100 ft lb) is reached. Refer to Figure 6-41.

60. After installation is complete, connect the brake piping to each brake.

FAM0612 6/10

Chassis Assembly

Page 6-35

FIGURE 6-42.

61. Connect the steering cylinders and the tie rod to the steering arms. Refer to Figure 6-42.

The tie rod toe-in must be adjusted once the tires and the body are installed. The toe-in adjustment procedure is located in Section 10, Appendix.

Page 6-36

Chassis Assembly

6/10 FAM0612

FIGURE 6-43.

62. Install the diagonal ladder. The weight of the diagonal ladder is approximately 180 kg (397 lb). Refer to Figure 6-43.

Tighten the cap screws to standard torque. Refer to Standard Tables in Section 10, Appendix.

FAM0612 6/10

Chassis Assembly

Page 6-37

FIGURE 6-44.

63. Lift the RH upright into position and install the four cap screws. Tighten to 465 ± 47 N·m (343 ± 34 ft lb). The weight of the RH upright with air cleaners is approximately 810 kg (1,785 lb). Refer to Figure 6-44.

NOTE: DO NOT weld the torque tubes on the uprights until the decks are installed.

Page 6-38

Chassis Assembly

6/10 FAM0612

FIGURE 6-45.

64. If installed, remove the center deck to enable easier installation of the air intake tubing and the two diagonal beams. The weight of the center deck is approximately 250 kg (551 lb).

65. Lift the RH diagonal beam into position. The weight of the beam is 68 kg (150 lb). Refer to Figure 6-45.

NOTE: Do not tighten the cap screws until the decks are in place.

FAM0612 6/10

Chassis Assembly

Page 6-39

FIGURE 6-46.

66. Lift the air intake tubes and hump hoses into place. Install and tighten the clamps that secure the hoses. Refer to Figure 6-46.

Page 6-40

Chassis Assembly

6/10 FAM0612

FIGURE 6-47.

67. Lift the center deck into position. Tighten the four cap screws to 465 ± 47 N·m (343 ± 34 ft lb). Refer to Figure 6-47.

FAM0612 6/10

Chassis Assembly

Page 6-41

FIGURE 6-48.

68. Install the handrails and lift the LH deck into place. The weight of the LH deck with handrails is approximately 720 kg (1587 lb). Loosely install the eight cap screws. Refer to Figure 6-48.

Page 6-42

Chassis Assembly

6/10 FAM0612

FIGURE 6-49.

69. Lift the retarding grid into place on the RH deck. The weight of the grid is approximately 2 742 kg (6,045 lb).

Tighten the eight cap screws to the standard torque.

70. Install the handrails on the RH deck. Lift the RH deck into position and loosely install the six cap screws. The weight of the deck/retarding grid assembly is approximately 3 830 kg (8,444 lb). Refer to Figure 6-49.

71. After all decking is in place, tighten the cap screws on each deck to 465 ± 47 N·m (343 ± 34 ft lb).

FAM0612 6/10

Chassis Assembly

Page 6-43

FIGURE 6-50.

72. Lift the operator cab into position. The weight of the cab is approximately 2 725 kg (6,008 lb). Refer to Figure 6-50.

73. Remove any paint from the cab mounting holes.

74. Determine if shims are required at each mounting pad. The gap between the cab and the ROPS support must not exceed 1 mm (0.04 in.). Install shims at each mounting pad as required.

Page 6-44

Chassis Assembly

6/10 FAM0612

FIGURE 6-51.

75. Install and tighten the 32 cap screws to 800 ± 80 N·m (590 ± 59 ft lb). Refer to Figure 6-51.

FAM0612 6/10

Chassis Assembly

Page 6-45

FIGURE 6-52.

76. Lift the electrical control cabinet into position. The weight of the cabinet is approximately 3 175 kg (7,000 lb).

Install the mounting hardware and shims. Tighten the 10 cap screws to 1 600 ± 160 N·m (1,180 ± 118 ft lb).

Refer to Figure 6-52.

77. Tighten the hardware for the diagnonal beams. For the RH beam, tighten the 12 cap screws to 240 ± 24 N·m (177 ± 17 ft lb). For the LH beam, tighten the 16 cap screws to 800 ± 80 N·m (590 ± 59 ft lb). Refer to Figures 6-13 and 6-45.

Page 6-46

Chassis Assembly

6/10 FAM0612

FIGURE 6-53.

78. Weld the RH upright to the front frame tube. Refer to Figure 6-53.

FAM0612 6/10

Chassis Assembly

Page 6-47

FIGURE 6-54.

79. Lift the two bumper extensions into place. Tighten the cap screws to standard torque. Refer to Figure 6-55.

Page 6-48

Chassis Assembly

6/10 FAM0612

FIGURE 6-55.

80. Install any remaining handrails. Tighten the cap screws to standard torque.

FAM0612 6/10

Chassis Assembly

Page 6-49

81. Connect the wiring for the electrical control cabinet, auxiliary control cabinet, and retarding grid box.

NOTE: The auxiliary control cabinet may be shipped with the external wiring already connected.

82. Install the air intake ductwork and tighten the connecting hardware. The weight of the alternator blower inlet duct is approximately 295 kg (650 lb). Refer to Figures 6-56 through 6-61.

FIGURE 6-56.

Page 6-50

Chassis Assembly

6/10 FAM0612

FIGURE 6-57.

FIGURE 6-58.

FAM0612 6/10

Chassis Assembly

Page 6-51

FIGURE 6-59.

FIGURE 6-60.

Page 6-52

Chassis Assembly

6/10 FAM0612

FIGURE 6-61.

FAM0612 6/10

Chassis Assembly

Page 6-53

FIGURE 6-62.

83. Install the parking brake adapter, retainer plate, hardened flat washer and capscrew. Tighten the capscrew to 595 - 670 N¡m (400 - 495 ft lb). Refer to Figure 6-62.

Page 6-54

Chassis Assembly

6/10 FAM0612

FIGURE 6-63.

84. Attach a lifting device to the parking brake assembly and lift into position. Refer to Figure 6-63.

85. Use a port-a-power to release spring pressure and allow the alignment of the brake discs during installation.

86. Seat the parking brake assembly against the housing and install the eight cap screws and washers. Tighten to standard torque.

FAM0612 6/10

Chassis Assembly

Page 6-55

Wheel Motor Installation 87. Thoroughly clean the cap screw holes and the mounting faces of the rear axle housing and wheel motor.

88. Inspect the cap screw holes in the rear axle housing for damage. Re-tap any holes that have damaged threads. Thoroughly clean any cap screw holes that have been re-tapped.

89. Check the mounting faces of the rear axle housing and the wheel motor for surface defects (nicks, scratches, etc). Repair any defects before installing the wheel motor.

90. Check the flatness of both mounting faces of the rear axle housing. Check the flatness at four equally spaced intervals (for example, 0°, 45°, 90° and 135°).

The maximum allowable variation in flatness is 2.29 mm (0.09 in.). Do not use a rear axle housing that does not meet this specification.

91. Apply a lithium based grease to the threaded cap screw holes in the rear axle housing.

92. Install two guide pins 180° apart (3 o’clock and 9 o’clock positions) in the rear axle housing.

Each complete wheel motor assembly weighs approximately 18 132 kg (39,975 lb). Ensure that the lifting devices are capable of handling the load safely.

93. Lift the wheel motor into position on the rear axle housing. Ensure that all cables and hoses are clear before installation. Refer to Figure 6-64.

If the brake system hoses are installed, guide them through the spindle holes during installation.

NOTE: When lifting the wheel motors, do not lift under the brake assembly. Shipping fasteners installed in the outboard rim bolt circle must remain in place during lifting and installation of wheel motors.

Page 6-56

Chassis Assembly

6/10 FAM0612

FIGURE 6-64.

FAM0612 6/10

Chassis Assembly

Page 6-57

The wheel motors must be properly aligned before installing them onto the rear axle housing. The wheel motor has markings which help determine installation orientation. Two sets of dimples are located at the 3 o’clock and 9 o’clock positions. A centerline symbol marks the 12 o’clock position of the wheel motor.

Refer to Figure 6-65.

The axle housing also contains dimples at the 3 o’clock and 9 o’clock positions next to the wheel motor mounting rings. Refer to Figure 6-66.

When installing the wheel motors, make sure that the markings on both components line up. The top cap screw hole on the rear axle housing may also be determined by counting the holes in between the two sets of punch marks. The top hole on the rear axle housing should line up with the “CL” stamping on the wheel motor.

Page 6-58

Chassis Assembly

6/10 FAM0612

FIGURE 6-65. WHEEL MOTOR DIMPLE MARKINGS

Punch Marks

FIGURE 6-66. REAR AXLE HOUSING DIMPLE MARKINGS

FAM0612 6/10

Chassis Assembly

Page 6-59

High tightening force is required to install the cap screws that secure the wheel motors to the rear axle housing. Repeated tightening will result in cap screw fatigue and damage.

Do not reuse any wheel motor mounting hardware (cap screws and hardened washers). Replace the hardware after one use.

Do not retighten any wheel motor mounting cap screw that has loosened after the truck has been placed into operation. If any wheel motor mounting cap screw has loosened during truck operation, all of the cap screws and hardened washers must be replaced with new hardware.

The cap screws that are used to secure the wheel motors to the rear axle housing are specially hardened to meet or exceed Grade 8 specifications. Replace these cap screws with only new cap screws of the correct hardness. Refer to the appropriate parts book for the correct part number.

The use of dry threads in this application is not recommended. Due to the high tightening force that is required to install the wheel motor mounting cap screws, dry threads may cause damage to tools, cap screws or the rear axle housing.

Komatsu does not recommend the use of special friction-reducing lubricants, such as Copper Coat, Never-SeezÂŽ or other similar products, on the threads of standard fasteners where standard torque values are applied. The use of special friction-reducing lubricants will significantly alter the clamping force during the tightening process. If a special friction-reducing lubricant is used, excessive stress and possible breakage of the fasteners may result.

94. Select the hardware to be installed in Group 1 of the tightening sequence. Refer to Figure 6-68.

95. Inspect each cap screw for rust, corrosion and surface defects on any seat or thread. Do not use any cap screw if a defect is suspected.

96. Lubricate the cap screw threads, cap screw head seats and washer faces with a lithium based grease containing 5% molybdenum-disulphide.

NOTE: The special hardened washers that are used in this application may have a punch lip on one side due to the manufacturing process. When placing this washer under the cap screw head, the washers must be installed with the punch lip facing away from the cap screw head to prevent damage to the fillet between the cap screw head and the shank. Refer to Figure 6-67.

FIGURE 6-67. INSTALLATION OF HARDENED WASHER 1. Washer 2. Cap Screw

Page 6-60

Chassis Assembly

6/10 FAM0612

97. Install the hardware for Group 1. Tighten each cap screw to 542 N•m (400 ft lb).

98. Repeat steps 94 - 96 for each remaining group in the tightening sequence. Refer to Figure 6-68.

Install and tighten all of the hardware in a group before proceeding to the next group in the tightening sequence. Remove the guide pins that were installed in step 92 when installing the hardware for Groups 3 and 4.

99. After all of the hardware in all of the groups has been installed and tightened to 542 N•m (400 ft lb), move back to Group 1. Increase the torque on each cap screw in Group 1 to 2 006 N•m (1,480 ft lb). Repeat this step for each remaining group in the tightening sequence. Refer to Figure 6-68.

FIGURE 6-68. WHEEL MOTOR MOUNTING HARDWARE INSTALLATION SEQUENCE

FAM0612 6/10

Chassis Assembly

Page 6-61

100. Connect the power cables and the speed sensors to each of the wheel motors. Connect the brake apply lines, brake cooling supply lines and return lines to each wheel. Refer to Figures 6-69 through 6-72.

FIGURE 6-69.

FIGURE 6-70.

Page 6-62

Chassis Assembly

6/10 FAM0612

FIGURE 6-71.

FIGURE 6-72.

FAM0612 6/10

Chassis Assembly

Page 6-63

Front Wheel Installation

NOTE: Remove all dirt and rust from mating parts before installing the tire and rim assembly.

101. Grip the tire and rim assembly with the tire handler. Align the tire inflation hose and the wheel hub. Position the rim onto the wheel hub studs. Refer to Figure 6-73.

102. Lubricate all stud threads and nut seating flanges with lithium base grease. Refer to Figure 6-74. Install and tighten the nuts in the following sequence: a. Install six nuts at the 12 o'clock position and six nuts at the 6 o'clock position. Tighten each nut to 2 326 ± 136 N·m (1,715 ± 100 ft lb). b. Install three nuts directly below the 3 o'clock position and three nuts directly above the 9 o'clock position.

Tighten the nuts to 2 326 ± 136 N·m (1,715 ± 100 ft lb). c. Install three nuts directly above the 3 o'clock position and three nuts directly below the 9 o'clock position.

Tighten these nuts to 2 326 ± 136 N·m (1,715 ± 100 ft lb). d. Install the remaining nuts and tighten in a clockwise pattern to 2 326 ± 136 N·m (1,715 ± 100 ft lb). e. Retighten all nuts in a clockwise pattern to the required 2 326 ± 136 N·m (1,715 ± 100 ft lb).

After the truck has been assembled and is operational, the truck must be operated for a short period of time, and the torque on the wheels re-checked. Tighten the wheels to the specified torque.

Page 6-64

Chassis Assembly

6/10 FAM0612

FIGURE 6-73.

FIGURE 6-74.

FAM0612 6/10

Chassis Assembly

Page 6-65

Rear Wheel Installation

FIGURE 6-75. REAR WHEEL ASSEMBLY 1. Wheel Motor Mounting Flange 2. Inner Wheel Rim 3. Disc Brake Assembly 4. Extension

5. Wheel Hub 6. Flanged Nut 7. Inner Extension 8. Clamps 9. Adapter Ring

10. Flanged Nut 11. Flanged Nut 12. Wheel Motor Transmission 13. Extension

14. Bracket 15. Outer Wheel Rim

NOTE: Clean all mating surfaces and check the stud threads before installing the wheels.

103. Bleed the disc brakes before installing the rear tires. Refer to Section J of the shop manual for brake bleeding procedures.

104. Grip the inner tire and rim with the tire handler and lift the wheel onto the wheel hub. Refer to Figures 6-76 and 6-77. Align extension (4, Figure 6-75) for mating with inner extension (7).

105. Lubricate all stud threads and nut seating flanges with a lithium base grease. Install and tighten the nuts in the following sequence: a. Install six nuts at the 12 o'clock position and six nuts at the 6 o'clock position. Tighten to 2 326 ± 136 N·m (1,715 ± 100 ft lb). b. Install three nuts directly below the 3 o'clock position and three nuts directly above the 9 o'clock position.

Tighten to 2 326 ± 136 N·m (1,715 ± 100 ft lb). c. Install three nuts directly above the 3 o'clock position and three nuts directly below the 9 o'clock position.

Tighten to 2 326 ± 136 N·m (1,715 ± 100 ft lb). d. Install the remaining nuts in a clockwise pattern. Tighten to 2 326 ± 136 N·m (1,715 ± 100 ft lb). e. Retighten all nuts in a clockwise pattern to the required 2 326 ± 136 N·m (1,715 ± 100 ft lb).

106. Install inner extension (7, Figure 6-75) and clamps (8) before installing the outer tires.

Page 6-66

Chassis Assembly

6/10 FAM0612

FIGURE 6-76.

FIGURE 6-77.

FAM0612 6/10

Chassis Assembly

Page 6-67

DO NOT move the truck without the rear, outer tires installed. Serious mechanical damage to the wheel motor hub and torque tube may result. The adapter rings and outer dual tires must be installed. The mounting cap screws must be tightened to 2 325 N·m (1,715 ft lb).

107. Position the rim adaptors into place on each outer rim. Install the fifty flanged nuts and tighten the nuts to 2 325 ± 136 N·m (1,715 ± 100 ft lb). Refer to Rear Wheel Installation for the correct tightening sequence.

Install the outer tires and tighten the fifty nuts to 2 325 ± 136 N·m (1,715 ± 100 ft lb). Refer to Rear Wheel Installation for the correct tightening sequence. Refer to Figure 6-78.

After the truck has been assembled and is operational, the truck must be operated for a short period of time, and the torque on the wheels re-checked. Tighten the wheels to the torque specified above.

108. Connect the electrical harnesses and hydraulic hoses below the operator’s cab. Refer to Figure 6-79.

Page 6-68

Chassis Assembly

6/10 FAM0612

FIGURE 6-78.

FIGURE 6-79.

FAM0612 6/10

Chassis Assembly

Page 6-69

109. Install the front LH and RH mud flaps on the underside of each deck.

110. Weld both rear LH and RH mud flap brackets into place on the backside of the deck supports.

Install the mud flaps.

Refer to Figures 6-80 and 6-81.

The truck is now ready for body installation.

Page 6-70

Chassis Assembly

6/10 FAM0612

FIGURE 6-80.

FIGURE 6-81.

FAM0612 6/10

Chassis Assembly

Page 6-71

NOTES

Page 6-72

Chassis Assembly

6/10 FAM0612

DUMP BODY ASSEMBLY GENERAL INFORMATION

The total weight of the body is approximately 30 362 kg (66,937 lb). Use two cranes for assembling the body. A 45 metric ton (50 ton) crane and a 109-136 metric tons (120-150 ton) crane are required. The larger crane is needed to help turn the body over after completion of the underside welding.

Assembly of the body must be performed on flat terrain with an adequate area for welding machines and for maneuvering lifting equipment.

If the body is being welded in a cold climate, it is advisable to move the parts to be welded into an enclosed shop area. Surfaces to be welded must be dry and the temperature must be above 10°C (50°F).

If shop space is not available, it may be necessary to provide a portable enclosure and pre-heat the parts prior to welding.

In most instances, it is easier to assemble and weld the body while the sections are upside down. After the pivot, guide pin, and body pads are welded in place, the body can be turned over and the remainder of the assembly can be completed.

All paint must be removed from surfaces to be welded. Use a wire brush or paint removal equipment.

Refer to the assembly drawings shipped with the truck for specific welding details and the parts required for assembly.

Body sections must be assembled as originally manufactured. Match the shipping numbers stenciled on the body sections to mate the correct parts. DO NOT mix components.

FIGURE 7-1. BODY PARTS NOMENCLATURE 1. Canopy 4. Lift Hole 7. LH Side Sheet 2. Front Sheet 5. Floor 3. RH Side Sheet 6. Pivot

FAM0703

Dump Body Assembly

7-1

BODY ASSEMBLY NOTE: References to LH and RH in the following procedures assume the body is in its' normal, upright position, as shown in Figure 7-1.

1. Organize the body sections in a large, flat, open space. Position the sections side by side and upside down. Arrange the sections so they are properly oriented for assembly. Refer to Figure 7-2 for domestic configuration, and 7-3 for international configuration.

FIGURE 7-4.

5. Use the hydraulic jack to align the body halves at the rear. Install cap screw (1, Figure 7-5) and the sleeve.

NOTE: Figure 7-5 shows the hardware numbered in installation sequence. Cap screws (1, 2 & 7) are marked with an asterisk (*). These cap screws are installed with sleeves. The remainder of the cap screws do not have sleeves.

6. Install cap screw (2) and the sleeve at the front of the floor.

FIGURE 7-2. DOMESTIC LAYOUT

7. Install cap screw (3) in the front sheet near the floor. Attach a wedge or a clamp inside the body as necessary to align the front sheet.

8. Use a wedge to align the front sheet and canopy. Install cap screws (4, 5 & 6).

9. Install cap screw (7) and the sleeve in the front of the canopy.

10. Install cap screws (8 & 9).

11. Install the backer strips on the front sheet center joint as shown on the assembly drawing.

FIGURE 7-3. INTERNATIONAL LAYOUT

NOTE: The backer strips must be tack welded in a location where the tack will be burned away on the first pass.

12. Loosely install cap screws (10 & 11) in the floor.

13. Loosen cap screws (1 & 2).

2. Remove the paint from the weld areas.

3. Lift the RH body half and support the front sheet, side sheets, and rear edge of the floor with blocks. Refer to Figure 7-4.

4. Lift the LH body and support with blocks under the front sheet and side sheet. Position a hydraulic jack on blocks at the tail end to support the floor at the rear. Refer to Figure 7-5.

7-2

14. Attach appropriate lifting apparatus to the body pivot. Insert the lifting apparatus through the body pin bores. The weight of the pivot is approximately 1492 kg (3289 lb). DO NOT damage the bores.

15. Lift the pivot over the body. Lower the pivot into position against the rear of the body, as shown in Figure 7-6. Align the pivot with the body sills.

Dump Body Assembly

FAM0703

NOTE: Figures 7-5 & 7-6 illustrate a domestic configuration with the canopy attached to the body halves. The canopy for international bodies is shipped as a separate piece. Do not attach the international canopy at this time

FIGURE 7-5. BODY ASSEMBLY HARDWARE INSTALLATION SEQUENCE

FIGURE 7-6. BODY PIVOT INSTALLATION

FAM0703

Dump Body Assembly

7-3

16. If necessary, use a hydraulic jack or crane to raise the center of the body to allow the pivot to fit inside the bolsters. Loosely install the cap screws in the pivot.

17. If assembling an international body (threepiece), lift the canopy into position at this time.

Install the canopy cap screws and tighten.

18. Tighten all floor, front sheet, and canopy cap screws. Use a chalk line to align the front of the canopy.

19. Tighten the pivot cap screws.

20. Install the filler plates and backer strips for the pivot to body sill weld joints.

21. Check the alignment and fit of all components 22. Tack weld the joints.

BODY WELDING Follow the guidelines listed below when welding the body: • Use dry weld rod or weld wire.

• Weld surfaces must be dry and above 10°C (50°F).

• If stick electrode is used, use as large a diameter rod as practical to weld the floor and front sheet joints.

• The following sequence must be followed for the front sheet: First Pass: Back step and skip weld in 10 increments along the entire length of the joint.

Refer to Figure 7-7.

Repeat the same procedure until the entire joint is filled. DO NOT stop welding until entire joint is complete.

• The body floor “V” groove must also be welded using the same procedure as the front sheet.

Weld from the front to the rear. Refer to Figure 77.

FIGURE 7-7. FRONT SHEET & FLOOR JOINT WELDING SEQUENCE

1. Complete the welds at the center seam, the front sheet and the canopy. Refer to the assembly drawings for welding requirements.

2. Remove the canopy alignment blocks.

7-4

Dump Body Assembly

FAM0703

3. Install the remaining gussets, the body guide and the body pad mounts. Refer to Figures 7-8 through 7-11.

DO NOT install the heated body exhaust boxes onto the body at this time. The exhaust boxes must be installed after the body is installed onto the truck.

FIGURE 7-10.

FIGURE 7-8.

FIGURE 7-11.

4. Once the body underside is completed, the body can be turned over. Use two cranes to invert the body, a 45 metric ton (50 ton) crane and a 109-136 metric ton (120-150 ton) crane.

The following photographs show a typical example of a body being inverted with two cranes.

FIGURE 7-9.

FAM0703

Position the body onto support blocks as shown in Figure 7-18.

Dump Body Assembly

7-5

FIGURE 7-12.

FIGURE 7-14.

FIGURE 7-15.

FIGURE 7-13.

FIGURE 7-16.

7-6

Dump Body Assembly

FAM0703

5. Refer to Figure 7-7 and the body assembly print to complete the welds on the inside of the body.

FIGURE 7-17.

FIGURE 7-19.

FIGURE 7-18.

FIGURE 7-20.

FAM0703

Dump Body Assembly

7-7

6. Install the mud flap brackets, clearance light housings (Figure 7-21), etc. as specified on the installation drawings.

7. Install any optional equipment such as body liners and side boards (Figure 7-22).

FIGURE 7-22.

FIGURE 7-21.

8. Clean the weld joints and paint.

7-8

Dump Body Assembly

FAM0703

FINAL ASSEMBLY • Inspect all lifting devices. Slings, chains, and cables used for lifting components must be inspected daily for serviceable condition. Refer to the manufacturer’s guidelines for correct capacities and safety procedures when lifting components. Replace any questionable items.

• Slings, chains and cables used for lifting must be rated for approximately two times the intended load.

• When in doubt as to the weight of components or any assembly procedure, contact your customer support manager for further information.

• Lifting eyes and hooks must be fabricated from the proper materials and rated to lift the intended load.

• Never stand beneath a suspended load. Guy ropes are recommended for guiding and positioning a suspended load.

• Before lifting the body, ensure there is adequate clearance between the body and overhead structures or electric power lines.

FAM0811 6/10

Final Assembly

Page 8-1

FIGURE 8-1.

1. Body welding and chassis assembly must be completed before proceeding.

Before the body is lifted off the ground, tie guy ropes to each of the four corners of the body for aiding in installation.

There are two methods of installing the body depending on the cranes available. a. If the truck is operational and can be driven, two 50 ton cranes can be used, one positioned at either side of the body. The body can then be lifted high enough to allow the truck to be reverse propelled under the body. Refer to Figures 8-1, 8-2 and 8-3. b. If a large crane of approximately 150 ton is available, the body can be lifted over the chassis and installed in a similar fashion to that in Step a.

Page 8-2

Final Assembly

6/10 FAM0811

FIGURE 8-2.

FIGURE 8-3.

FAM0811 6/10

Final Assembly

Page 8-3

2. Install shims (8, Figure 8-5) in both body pivots, as required, to fill the outside gaps and center the body on the frame pivot.

NOTE: Do not install shims on the inside. A minimum of one shim is required at the outside end of both frame pivots.

3. Align the hole in body pivot pin (4) with the bolt hole in the pin retainer on the outer body pivot ear. Push the body pivot pin through the outer body pivot ear, the frame pivot, and the inner body pivot ear.

4. Install shoulder bolt (1) through the body pivot pin. Install flat washer (2) and nut (2). Tighten the nut to 339 N•m (250 ft lb).

Page 8-4

Final Assembly

6/10 FAM0811

FIGURE 8-4.

FIGURE 8-5. DUMP BODY PIVOT PIN 1. Shoulder Bolt 2. Flat Washer 3. Nut

FAM0811 6/10

4. Body Pivot Pin 5. Pivot Bushing 6. Body Pivot Ear

Final Assembly

7. Pivot Bushing 8. Shim 9. Body Pivot Bushing

Page 8-5

5. Align the hoist cylinder bearing eye with the bore of hoist cylinder upper mounting bracket (1, Figure 8-7).

6. Align the bolt hole in pivot pin (3) with the bolt hole in mounting bracket (1). Install the pivot pin through the first spacer (2), then align the second spacer with the bore on the other side of hoist cylinder bearing eye.

Finish installing the pin through second spacer (2).

7. Install shoulder bolt (4) through each pin.

NOTE: Do not use a flat washer under the head of the shoulder bolt. This will ensure that the shoulder bolt does not run out of threads when tightening.

8. Install flat washer (5) and nut (6) onto the threaded end of each shoulder bolt. Tighten the nuts to 339 N¡m (250 ft lb).

Page 8-6

Final Assembly

6/10 FAM0811

FIGURE 8-6.

FIGURE 8-7. HOIST CYLINDER UPPER MOUNT 1. Mounting Bracket 2. Spacer

FAM0811 6/10

3. Pivot Pin 4. Shoulder Bolt

Final Assembly

5. Flat Washer 6. Nut

Page 8-7

FIGURE 8-8.

10. Shim the body pads as required. All pads, except the two rear pads, should contact the frame with approximately equal compression of the rubber. Refer to Figures 8-8 and 8-9.

A gap of approximately 1.5 mm (0.06 in.) is required at each rear pad. This can be accomplished by using one less shim at each rear pad.

11. Inspect pad contact. If pad contact appears to be unequal, correct as necessary.

NOTE: Proper body pad to frame contact is required for maximum pad life.

Page 8-8

Final Assembly

6/10 FAM0811

FIGURE 8-9. BODY PAD INSTALLATION 1. Dump Body 2. Body Pad

FAM0811 6/10

3. Shim 4. Mounting Hardware

Final Assembly

Page 8-9

FIGURE 8-10.

10. Tack weld rock ejector mounting brackets into position on the underside of the body. Refer to Figure 8-11.

The ejectors must be positioned on the center line between the rear tires within 6.0 mm (0.25 in.). Before welding, drop a plumb line to check rock ejector clearance. Position the rock ejector a distance of 455 mm (17.9 in.) from the wheel housing. Refer to Figure 8-12.

NOTE: With rock ejector arm (1) hanging vertical as shown in Figure 8-12, there must be no gap at stop block (3, Figure 8-11).

If the rock ejector arms are bent during operation, they must be removed and straightened. Inspect mounting brackets (4, Figure 8-11), pins (2) and stops (3) at each shift change for wear and/or damage. Repair as necessary.

Page 8-10

Final Assembly

6/10 FAM0811

FIGURE 8-11. ROCK EJECTOR MOUNTING 1. Rock Ejector Arm 2. Pin

3. Stop Block 4. Mounting Bracket

FIGURE 8-12. ROCK EJECTOR INSTALLATION 1. Rock Ejector Arm

FAM0811 6/10

2. Wheel Housing

Final Assembly

Page 8-11

FIGURE 8-13.

FIGURE 8-14.

Page 8-12

Final Assembly

6/10 FAM0811

FIGURE 8-15.

11. Install the remaining axle housing air ducts and hatch cover. Refer to Figures 8-13, 8-14 and 8-15.

FAM0811 6/10

Final Assembly

Page 8-13

FIGURE 8-16.

FIGURE 8-17.

12. Install the mud flaps onto the body and chassis. Refer to Figures 8-16 and 8-17.

Page 8-14

Final Assembly

6/10 FAM0811

NOTES

FAM0811 6/10

Final Assembly

Page 8-15

FIGURE 8-18.

13. Install both body guide brackets loosely into place. Refer to Figure 8-18.

Once in position, slowly lower the body and mark the position in which the brackets are to be welded. The body guides must be centered between wear plates (3, Figure 8-19), with a maximum gap of 4.8 mm (0.19 in.) at each side.

14. With the body in its lowered position on the frame rail, the position of body up limit switch actuator arm (4, Figure 8-20) can be marked on the underside of the body. Refer to the assembly prints for precise positioning specifications.

Raise the body enough to be able to weld the mounting pad to the underside of the body.

Before welding, install support blocks between the body and the frame.

15. Raise the body and install the body up sling. Remove the support blocks.

16. Weld the body guide brackets into place. Refer to Figures 8-18 and 8-19.

Page 8-16

Final Assembly

6/10 FAM0811

FIGURE 8-20. BODY-UP SWITCH INSTALLATION

FIGURE 8-19. BODY GUIDE 1. Dump Body 2. Body Guide

FAM0811 6/10

3. Body Guide Wear Plates

1. Switch Mounting Bracket 2. Adjustment Cap Screws 3. Proximity Switch

Final Assembly

4. Actuator Arm 5. Adjustment Screws

Page 8-17

FIGURE 8-21.

FIGURE 8-22.

17. If the truck is to be equipped with a heated body, install the exhaust box at the pivot and tighten the hardware (Refer to Figures 8-21 and 8-22.

Page 8-18

Final Assembly

6/10 FAM0811

FIGURE 8-23.

18. If the truck is to be equipped with mufflers, install them at this time. Refer to Figure 8-23.

FAM0811 6/10

Final Assembly

Page 8-19

FIGURE 8-24.

19. With the body in the raised position, set the body hoist limit switch and weld the target into position. Refer to Figure 8-24.

The switch should activate 152 mm (6 in.) before maximum cylinder stroke. Refer to the assembly prints for specifications.

Page 8-20

Final Assembly

6/10 FAM0811

FIGURE 8-25.

20. With the body in the raised position, install the grease lines for the hoist cylinders and clamp along the inside of the body. Refer to Figure 8-25.

FAM0811 6/10

Final Assembly

Page 8-21

FIGURE 8-26.

21. Install the exhaust tubing blankets. Refer to Figure 8-26.

Page 8-22

Final Assembly

6/10 FAM0811

FIGURE 8-27.

22. Install the LH and RH engine bay lights. Refer to Figure 8-27.

FAM0811 6/10

Final Assembly

Page 8-23

FIGURE 8-28.

23. Install add-on components such as the lubrication system and the oil reserve system. Verify that all electrical and hydraulic connections are correct. Refer to Figure 8-28 and 8-29.

Page 8-24

Final Assembly

6/10 FAM0811

FIGURE 8-29.

FAM0811 6/10

Final Assembly

Page 8-25

FIGURE 8-30.

FIGURE 8-31.

Page 8-26

Final Assembly

6/10 FAM0811

FIGURE 8-32.

24. Install the fire suppression system. Refer to Figures 8-30, 8-31 and 8-32.

NOTE: This installation is normally performed by the fire system distributor.

25. Paint the truck as needed.

FAM0811 6/10

Final Assembly

Page 8-27

FIGURE 8-33.

26. Install the anti-skid strips at the designated areas on the decks. Refer to Figure 8-33.

Page 8-28

Final Assembly

6/10 FAM0811

FIGURE 8-34.

27. Install all decals on their designated areas. Refer to the installation drawing for all decal locations.

28. After completing the assembly of the truck: a. Verify that all cap screw heads or nuts are marked with paint, indicating they have been properly tightened. b. Check all hydraulic lines and electrical connections for secure installation. c. Notify qualified maintenance personnel that the truck is ready for final static and dynamic systems checkout.

FAM0811 6/10

Final Assembly

Page 8-29

FIGURE 8-35.

FIGURE 8-36.

Page 8-30

Final Assembly

6/10 FAM0811

FINAL CHECKOUT Final checkout requires truck operation.

Place the operation and maintenance manual and safety manuals in the operator cab, if not already there.

Any personnel involved in the final check-out of the truck must read and understand all safety and operating instructions in the operation and maintenance manual.

1. Complete delivery and warranty forms.

2. Check all coolant and lubricants for proper levels and specifications. The lubrication chart is shown in Section 10, Appendix.

5. Perform a final check of all systems and prepare for operation. Several checks and tasks are outlined in Section 10, Appendix.

6. Complete the checks listed in the Field Assembly Inspection Report Form. A copy of the form is provided with the truck and is also available in Section 10, Appendix.

7. Operate the truck in a traffic-free area until safe operation has been validated.

8. Release the truck for use after all checks have been completed and all deficiencies corrected.

3. Verify the shut-off valves on the hydraulic tank suction lines are open.

4. Purge any air from the pumps and suction lines.

Pressure will not build if air is present. Operating the pumps with air in the system will result in damage. Refer to the truck assembly section for more information on how to bleed the air from the pumps and suction lines.

FAM0903 3/09

Final Checkout

Page 9-1

NOTES

Page 9-2

Final Checkout

3/09 FAM0903

APPENDIX This chapter contains additional information and procedures for aiding in field assembly of the truck. Refer to the list below for contents of this chapter. Refer to the latest service manual for additional information on servicing the truck.

1. Lubrication Chart - WB2790 2. Suspension Oiling And Charging Procedure 3. Toe In Adjustment Procedure 4. Automatic Lubrication System Checkout Procedure - EJ4060 5. Air Conditioning Checkout Procedure - EL4302 6. Air Conditioning Drive Belt Adjustment Procedure - EL9330 7. Hydraulic Checkout Procedure - EM7604 8. Brake Checkout Procedure - EM7346 9. VHMS Checkout Procedure - EM2129

10. Payload Meter III Checkout Procedure - EJ3061

11. Electrical Checkout Procedure - EF9650

12. Amendments to Electrical Checkout Procedure - EM8300

13. Webasto Coolant Heater Checkout Procedure - XB2949

14. Standard Torque Charts and CoversionTables

15. Field Assembly Inspection Report

16. 50 Hour Post-Commissioning Checksheet

FAM1014 6/10

Appendix

Page 10-1

NOTES

Page 10-2

Appendix

6/10 FAM1014

LUBRICATION CHART

NOTES

SUSPENSION OILING AND CHARGING PROCEDURE GENERAL

EQUIPMENT LIST

These procedures cover the oiling and charging of Hydrair® II suspensions on Komatsu 930E dump trucks.

•

Hydrair Charging Kit

•

Jacks and/or Overhead Crane

•

Support Blocks for: Oiling Height Dimensions (Front and Rear) Charging Height Dimensions (Front Only)

•

Hydrair Oil (See Specifications Chart)

•

Friction Modifier (See Specifications Chart)

•

Dry Nitrogen (See Specifications Chart)

Suspensions which have been properly charged will provide improved handling and ride characteristics while also extending the fatigue life of the truck frame and improving tire wear.

NOTE: Inflation pressures and exposed piston lengths are calculated for a normal truck gross vehicle weight (GVW). Additions to truck weight by adding body liners, tailgates, water tanks, etc. should be considered part of the payload. Keeping the truck GVW within the specification shown on the Grade/ Speed Retard chart in the operator cab will extend the service life of the truck main frame and allow the Hydrair II suspensions to produce a comfortable ride.

Installation of Charging Kit Assemble the charging kit as shown in Figure 4-1 and attach it to a container of pure dry nitrogen (8).

1. Remove the protective covers and charging valve caps from the suspensions.

2. Turn "T" handles (1, Figure 4-1) of adapters (2) completely counterclockwise.

All Hydrair II suspensions are charged with compressed nitrogen gas with sufficient pressure to cause injury and/or damage if improperly handled.

Follow all safety instructions, cautions, and warnings provided in the following procedures to prevent any accidents during oiling and charging.

Proper charging of Hydrair II suspensions requires that three basic conditions be established in the following order: 1. Oil level must be correct.

2. Suspension piston rod extension for nitrogen charging must be correct.

3. Nitrogen charge pressure must be correct.

For best results, Hydrair II suspensions should be charged in pairs (fronts together and rears together).

If rear suspensions are to be charged, the front suspensions should be charged first.

NOTE: For longer life of suspension components, a friction modifier should be added to the suspension oil. See the Specifications Charts at the end of this section.

NOTE: Setup dimensions in the Specifications Charts must be maintained during oiling and charging procedures. However, after the truck has been operated, these dimensions may vary.

FIGURE 4-1. HYDRAIR CHARGING KIT NOTE: The arrangement of parts may vary from the illustration depending on the kit part number.

1. “T” Handle Valve 2. Charging Valve Adapter 3. Manifold Outlet Valves (from gauge) 4. Inlet Valve (from regulator) 5. Regulator Valve (Nitrogen Pressure) 6. Manifold 7. Charging Pressure Gauge (Suspensions) 8. Dry Nitrogen Gas Container

3. Ensure outlet valves (3) and inlet valve (4) are closed (turned completely clockwise).

Support Blocks For Oiling And Charging Dimensions

4. Turn swivel nut (small hex) on the charging valve three full turns counterclockwise to unseat the valve.

Before starting the oiling and charging procedures, supports should be fabricated to maintain the correct exposed piston rod extensions.

5. Attach charging valve adapters (2) to each suspension charging valve stem.

6. Turn "T" handles (1) clockwise. This will depress core of charging valve and open the gas chamber of the suspension.

7. Open both outlet valves (3).

NOTE: By selective opening and closing of outlet valves (3), and inlet valve (4), suspensions may be charged separately or together.

Removal of Charging Kit 1. Close both outlet valves (3).

2. Turn "T" handles (1) counterclockwise to release the charging valve cores.

3. Remove charging valve adapters (2) from the charging valves.

4. Tighten the swivel nut (small hex) on the charging valve. If a new charging valve is being used, tighten the swivel nut to 15 N¡m (11 ft lb), then loosen and retighten the swivel nut to 15 N¡m (11 ft lb). Loosen the swivel nut again and retighten to 6 N¡m (50 in. lb). Install the valve cap finger-tight.

5. Install the charging valve caps and protective covers on both suspensions.

Nitrogen charging support blocks for the rear suspension are no longer necessary. However, oiling blocks are necessary to properly set the oiling height.

Exposed piston rod extensions are specified for both oil level and nitrogen charging for Hydrair II suspensions. These dimensions are listed in the tables below Figures 4-2 and 4-5. Measure the dimensions from the face of the cylinder gland to the machined surface on the spindle at the front suspension. At the rear suspension, measure from the face of the cylinder gland to the piston flange.

Support blocks may be made in various forms. Mild steel materials are recommended. Square stock or pipe segments at least 25 mm (1 in.) may be used.

Blocks must be capable of supporting the weight of the truck during oiling and charging procedures while avoiding contact with plated surfaces and seals on the suspension. Refer to Figure 4-2 for front suspension support block placement and Figure 4-4 for rear support block placement.

FRONT SUSPENSION

All Hydrair II suspensions are charged with compressed nitrogen gas with sufficient pressure to cause injury and/or damage if improperly handled. Follow all the safety notes, cautions and warnings in these procedures to prevent accidents during servicing and charging.

1. Park the unloaded truck on a hard, level surface. Apply the parking brake and chock the wheels.

2. Remove the charging valve cap. Turn the charging valve swivel nut (small hex) counterclockwise three full turns to unseat the valve seal. DO NOT turn the large hex. The charging valve body has a bleeder groove in its mounting threads, but for safety of all personnel, the valve body must not be loosened until all nitrogen pressure has been released from the suspension.

3. Depress the charging valve core to release nitrogen pressure from the suspension. When all nitrogen has been released, the suspension should have collapsed slowly and be seated solidly on the support blocks. Remove the top fill plug next to the charging valve (Figure 4-2).

2. Thoroughly clean the area around the charging valve on the suspensions. Remove the protective covers from the charging valves.

Front Suspension Oiling

When blocks are in place on a suspension, they must be secured with a strap or other means to avoid accidental discharge. An unsecured block could fly loose as weight is applied, presenting the possibility of serious injury to nearby personnel and/or damage to the equipment.

Overhead clearance may be reduced rapidly and suddenly when nitrogen pressure is released.

Make certain all personnel are clear and support blocks are secure before relieving nitrogen pressure from the suspension. Wear a face mask or goggles while relieving nitrogen pressure.

NOTE: For longer life of suspension components, a friction modifier should be added to the suspension oil. See the Specifications Charts at the end of this section.

1. Position and secure oiling height dimension blocks in place (Figure 4-2). The blocks should be positioned 180 degrees apart to provide stability. When nitrogen pressure is released, the suspensions will lower and rest on the blocks. Ensure that the blocks do not mar or scratch the plated surfaces of the pistons or damage wiper seals in the lower bearing retainer. Support blocks must seat on the spindle and the cylinder housing.

FIGURE 4-2. FRONT SUSPENSION

FRONT SUSPENSION DIMENSIONS (EMPTY) OILING HEIGHT

CHARGING HEIGHT

*CHARGING PRESSURE

25.4 mm (1.0 in.)

299 mm (9.0 in.)

2930 kPa (425 psi)

* with standard Rock Body Note: If the truck starts to lift off the blocks before charging pressure is attained, STOP CHARGING.

4. Fill the suspension with clean Hydrair oil (with 6% friction modifier) until the cylinder is full to the top of the fill plug bore. Use drip pans and clean all spillage from the outside of the suspension. Allow the suspension to settle for at least 15 minutes to clear any trapped nitrogen and bubbles from the oil. Add more suspension oil if necessary. Install a new O-ring on the fill plug and install the plug.

Front Suspension Nitrogen Charging

Lifting equipment (crane or hydraulic jacks) must be of sufficient capacity to lift the truck weight.

Be certain that all personnel are clear of the lift area before the lift is started. Clearances under the truck may be suddenly reduced.

1. If removed, install the charging valve with new O-ring (9, Figure 4-3). Lubricate the O-ring with clean Hydrair oil.

2. Tighten valve body (6) (large hex) to 23 N·m (17 ft lb). Swivel nut (4) (small hex) must be unseated by turning it counterclockwise three full turns.

Dry nitrogen is the only gas approved for use in Hydrair II suspensions. Charging of these components with oxygen or other gases may result in an explosion which could cause fatalities, serious injuries and/or major property damage. Use only nitrogen gas meeting the specifications shown in the Specifications Chart at the end of this section.

3. Install the Hydrair charging kit and a bottle of pure dry nitrogen. Refer to Installation of Charging Kit in this section.

4. Charge the suspensions with nitrogen gas to 50.8 mm (2 in.) greater than the charging height listed in Figure 4-2. Close inlet valve (4, Figure 4-1).

5. Remove the oiling blocks from the suspensions and install the nitrogen charging blocks. Secure the blocks to prevent accidental dislodging.

NOTE: Use caution to prevent damage to plated cylinder surfaces and oil seals when installing the blocks.

6. Remove the center hose from manifold (6).

7. Open inlet valve (4) until the pressure drops below the pressure listed in Figure 4-2, then close the valve.

8. Install the center hose to manifold (6).

9. Charge the suspensions to the pressure listed in Figure 4-2. DO NOT use an overcharge of nitrogen to lift the suspensions off the charging blocks.

10. Close inlet valve (4, Figure 4-1). Leave outlet valves (3) open for five minutes to allow the pressures in the suspensions to equalize.

11. Close outlet valves (3). Remove the charging kit components. Refer to Removal of Charging Kit in this section.

12. If the charging valve is being reused, tighten swivel nut (4, Figure 4-3) to 6 N·m (50 in. lb).

FIGURE 4-3. CHARGING VALVE 1. Valve Cap 2. Seal 3. Valve Core 4. Swivel Nut 5. Rubber Washer

6. Valve Body 7. O-Ring 8. Valve Stem 9. O-Ring

13. If a new charging valve is being used, tighten the swivel nut to 15 N·m (11 ft lb)), then loosen and retighten the swivel nut to 15 N·m (11 ft lb)). Loosen the swivel nut again and retighten to 6 N·m (50 in. lb). Install the valve cap fingertight.

14. Install the protective guard over the charging valve.

15. Raise the truck body in order to extend the front suspensions, allowing for removal of the nitrogen charging blocks. Ensure that sufficient overhead clearance exists before raising the body. If the suspensions do not extend after raising the body, turn the steering wheel from stop to stop several times. If the suspensions still do not extend enough to allow for removal of the blocks, use a crane or floor jacks to raise the truck and remove the blocks.

NOTE: For longer life of suspension components, a friction modifier should be added to the suspension oil. See the Specifications Charts at the end of this section.

1. Position and secure the oiling blocks in place so the blocks are seated between the frame and the rear axle housing (Figure 4-4). A block should be used on both the left and right sides of the truck.

The front Hydrair suspensions are now ready for operation. Visually check piston extension with the truck both empty and loaded. Record the extension dimensions. Maximum downward travel is indicated by the dirt ring at the base of the piston. Operator comments on steering response and suspension rebound should also be noted.

REAR SUSPENSION 1. Park the unloaded truck on a hard, level surface. Apply the parking brake, and chock the wheels.

2. Thoroughly clean the area around the charging valve on the suspensions. Remove the protective covers from the charging valves and the rubber covers from the suspension piston.

Rear Suspension Oiling FIGURE 4-4. OILING BLOCK INSTALLATION

When blocks are in place on a suspension, they must be secured with a strap or other means to avoid accidental discharge. An unsecured block could fly loose as weight is applied, presenting the possibility of serious injury to nearby personnel and/or damage to the equipment.

Overhead clearance may be reduced rapidly and suddenly when nitrogen pressure is released.

Make certain all personnel are clear and support blocks are secure before relieving nitrogen pressure from the suspension. Wear a face mask or goggles while relieving nitrogen pressure.

1. Main Frame 2. Oiling Support Block

3. Rear Axle Housing

2. Remove charging valve cap. Turn the charging valve swivel nut (small hex) counterclockwise three full turns to unseat the valve seal. DO NOT turn the large hex. The charging valve body has a bleeder groove in its mounting threads, but for safety of all personnel, the valve body must not be loosened until all nitrogen pressure has been released from the suspension.

3. Depress the charging valve core to release nitrogen pressure from the suspension. When all nitrogen pressure has been released, loosen and remove the fill plug. The suspension should have collapsed slowly as gas pressure was released. The weight of the truck is now supported by the support blocks.

NOTE: A plastic tube can be used to help bleed off trapped air inside the piston.

4. Remove the vent plug, pressure sensor, and charging valve (Figure 4-5). Use one of the open ports to fill the suspension with clean Hydrair oil (with 6% friction modifier). Fill until clean oil seaps from the open ports. Use drip pans and clean all spillage from the outside of the suspension. Allow the suspension to settle for at least 15 minutes to clear any trapped nitrogen and bubbles from the oil. Add more suspension oil if necessary.

5. Install the vent plug and pressure sensor onto the suspension.

6. Install a new O-ring onto the charging valve.

Lubricate the O-ring with clean Hydrair oil.

7. Install the charging valve onto the suspension.

Tighten valve body (6, Figure 4-3) to 23 N¡m (17 ft lb).

FIGURE 4-5. REAR SUSPENSION 1. Main Frame 2. Charging Valve

3. Rear Axle Housing

REAR SUSPENSION DIMENSIONS (EMPTY) OILING HEIGHT

CHARGING HEIGHT

*CHARGING PRESSURE

53 mm (2.1 in.)

218 mm (8.6 in.)

1296 kPa (188 psi)

* Note: Charging pressures are for reference only and may vary depending on body weights.

Rear Suspension Nitrogen Charging

Lifting equipment (overhead or mobile cranes, or hydraulic jacks) must be of sufficient capacity to lift the truck weight. Ensure that all personnel are clear of lift area before lifting is started.

Clearances under the truck may be suddenly reduced.

7. Ensure that both of the suspension cylinders are extended the same distance ± 10 mm (0.39 in.). If the difference in the extension from side to side exceeds this amount, check the front suspensions for equal extension. Adjust the front suspensions as necessary.

NOTE: A low left front suspension will cause the right rear suspension to be high. A low right front suspension will cause the left rear suspension to be high.

8. Close outlet valves (3). Remove the charging kit components. Refer to Removal of Charging Kit in this section.

9. If the charging valve is being reused, tighten swivel nut (4, Figure 4-3) to 6 N·m (50 in. lb).

Ensure that the automatic apply circuit has not applied the service brakes during truck maintenance. If the front brakes are applied during rear suspension charging, the axle cannot pivot for frame raising/lowering, and the rear suspension may be unable to move up or down.

10. If a new charging valve is being used, tighten the swivel nut to 15 N·m (11 ft lb), then loosen and retighten the swivel nut to 15 N·m (11 ft lb).

Loosen the swivel nut again and retighten to 6 N·m (50 in. lb). Install the valve cap finger-tight.

1. If removed, install charging valve with new Oring (9, Figure 4-3). Lubricate the O-ring with clean Hydrair oil.

11. Install the protective guards over the charging valves. Install the rubber covers over the piston rods.

2. Tighten valve body (6) (large hex) to 23 N·m (17 ft lb). Swivel nut (4) (small hex) must be unseated by turning it counterclockwise three full turns.

The rear Hydrair suspensions are now ready for operation. Visually check piston extension with the truck both empty and loaded. Record the extension dimensions. Maximum downward travel is indicated by the dirt ring at the base of the piston. Operator comments on steering response and suspension rebound should also be noted.

Dry nitrogen is the only gas approved for use in Hydrair II suspensions. Charging of these components with oxygen or other gases may result in an explosion which could cause fatalities, serious injuries and/or major property damage. Use only nitrogen gas meeting the specifications shown in the Specifications Chart at the end of this section.

3. Install Hydrair charging kit and a bottle of pure dry nitrogen. Refer to Installation of Charging Kit in this section.

4. Charge the suspensions with nitrogen gas to 38 mm (1.5 in.) greater than the charging height listed in Figure 4-5.

5. Slowly release gas until the suspensions match the charging height listed in Figure 4-5.

6. Close inlet valve (4, Figure 4-1). Leave outlet valves (3) open for five minutes to allow the pressures in the suspensions to equalize.

OIL AND NITROGEN SPECIFICATIONS CHARTS HYDRAIR® II OIL SPECIFICATIONS Ambient Temperature Range

-30°F & above (-34.5°C & above)

Part No.

Approved Sources

VJ3911 (need to add 6% of AK3761)

Sunfleet TH Universal Tractor Fluid Mobil 424 Chevron Tractor Hydraulic Fluid Mobil D.T.E. 15 Conoco Power Tran III Fluid Petro Texaco TDH Oil Canada Duratran Fluid AMOCO ULTIMATE Motor Oil Shell Canada Donax TDL 5W-30

AK4063

Suspension Oil (premixed with 6% Friction Modifier)

AK4064

-55°F & above (-48.5°C & above)

5 Gallon container 55 Gallon container

VJ5925 (need to add 6% of AK3761)

Emery 2811, SG-CD, 5W-30 Mobil Delvac I, 5W-30

Petro Canada Super Arctic Motor Oil, 0W-30 Conoco High Performance Synthetic Motor Oil, 5W-30

AK4065

Suspension Oil (premixed with 6% Friction Modifier)

5 Gallon container

AK4066

55 Gallon container

NOTE: VJ3911 and VJ5925 oils are not compatible and must not be mixed in a suspension.VJ3911 and VJ5925 oils are supplied in 5 gallon (19 Liter) cans.

FRICTION MODIFIER

FRICTION MODIFIER Mixing Instructions (94% Suspension Oil, 6% Friction Modifier)

Part Number

Suspension Oil

Amount of Friction Modifier to add

AK3761 (5 Gallon container of 100% Friction Modifier)

1 gallon of suspension oil

add 7.7 oz.

5 gallons of suspension oil

add 38.4 oz.

55 gallons of suspension oil

add 3.3 gal.

NITROGEN GAS (N2) SPECIFICATIONS HYDRAIR®

Nitrogen gas used in II Suspension Cylinders must meet or exceed CGA specification G-10.1 for Type 1, Grade F Nitrogen Gas

Property

Value

Nitrogen

99.9% Minimum

Water

32 PPM Maximum

Dew Point

-68°F (-55°C) Maximum

Oxygen

0.1% Maximum

TOE-IN ADJUSTMENT 1. The steering system must first be centered in the straight ahead position. Turn the key switch OFF. Allow at least 90 seconds for the accumulators to depressurize. DO NOT turn the steering wheel during this time.

2. Block the front and back of the rear wheels.

3. Check the toe-in by measuring the distance between the centers of the front tires. Obtain the measurements on the horizontal centerline at the front and rear of the tires. Refer to Figure 3-1.

Radial tires must have equal measurements at the front and the rear of the tires. Equal measurements results in zero toe-in.

4. Loosen the clamp locknuts on the tie rod.

Rotate the tie rod as necessary to obtain the correct toe-in setting of zero toe-in..

5. When the adjustment is complete, tighten the locknuts on the tie rod to 420 ± 42 N•m (310 ± 31 ft lbs).

6. Remove the blocks from the rear wheels.

930E TOE-IN DATA Nominal tie-rod length, radial tires to achieve zero toe-in

3667 mm (144.37 in.)

FIGURE 3-1. MEASURING TOE-IN

NOTES

KOMATSU

CHECKOUT PROCEDURE

IEJ4060-2 Page 1 of 2

NAME: Auto Lube Grease Procedure WRITTEN BY:

DATE:

B. Anderson CHECKED BY:

7-4-00 DATE:

M. McMullen APPROVED

BY:

7-7-00 DATE:

MACHINE & MODEL: Electric Trucks

2

Change Note 'Note some pumps, etc.

0 DASH ASIZE

DESCRIPTION OF CHANGE MICROFILM

I

I

9/16/04

-nt

1

I I

I

I

I

I

I

I

3/24/04

1\<...014111518

BA BA

114M MM

DATE

ECN

BY

CK'D

I

I

I

I

I

I

I

I

I

I

THE FOllOWING PROCEDURE MUST BE DONE ON INITIAL START-UP FOR THE LINCOLN INDUSTRIAL ROTARY HYDRAULIC GREASE PUMP WITH ADJUSTABLE CONTROLS. 1.

Check adjustment of pressure regular valve which should be set at 325 to 350 psi. (note this valve is parallel to pump motor and is suppose to be factory set @ 350 psi).

2.

Flow control valve should be set so a cycle would take 18 seconds to complete. (note this valve is perpendicular to pump motor).

LINCOLN INDUSTRIAL ROTARY HYDRAULIC GREASE PUMP WITH FIXED PUMP CONTROLS NO ADJUSTMENT CAN BE MADE. I.

Observe gauge during cycle 325 psi minimum pressure should be obtained.

2.

Flow control valve should be set so a cycle would take 16 to 20 secondsto complete.

THE FOllOWING PROCEDURES MUST BE DONE IN ORDER TO REMOVE ANY TRAPPED AIR THAT IS IN THE lUBE SYSTEMS AND PROPERLY lUBE THE SPHERICAL BEARINGS. 1. On initial start up of the system.

2.

When any parts or hoses are replaced or removed.

3.

During the factory build of the truck (before the truck ships). This includes ship loose parts.

4.

Prior to delivery of new units after field erection.

m c..

~ 0 0) 0 .

N

EJ4060-2.doc

Page 1 of2

KOMATSU

CHECKOUT PROCEDURE

IEJ4060-2 PaQe 2 of 2

PROCEDURE:

AUTO LUBE SYSTEMS

1. To purge the air from the main supply line, remove the main supply line at the Lincoln Lube canister and connect the shop grease pump to the supply line. (Some adaptation may be required to connect the shop grease pump to the supply line).

2.

Remove the pipe plugs from each injector group in sequence, (right front, left front and rear axle). Using the shop grease pump, pump the grease, until grease appears at the group of injectors and re-install the pipe plug. Repeat for the other 2 groups of injectors.

3.

Remove the shop grease pump from the main supply line and reconnect the main supply line to the grease canister.

4.

Remove the injector caps from each injector and connect the shop grease pump to the zerk fitting on the injector and pump grease until grease appears at the far end of the individual grease hose or at the joint that is being greased.

5.

Repeat Step 4 for all injectors on the truck.

PROCEDURE: 1.

STANDARD LUBE SYSTEMS

Connect the shop grease pump to each zerk fitting on the truck and pump grease until grease comes out of the far end of the individual grease hose or the joint that is being greased.

PROCEDURE:

FOR GREASING SPHERICAL BEARINGS (FACTORY ASSEMBLY)

Greasing the spherical bearings can be done by one or more of the following:

.

. .

Using the shop grease gun, pump the spherical bearing full of grease until grease is visible from both sides of the bearing. This is to be done on all spherical bearings.

On sub-assemblies not installed and not subject to final assembly inspection - install a zerk fitting into the port where the grease hose will be connected or use a tapered rubber adapter to push against the grease port.

On sub-assemblies where spherical bearings are installed and subject to final assembly inspection

-

use the standard grease system or the

Lincoln Lube System already installed and purged.

PROCEDURE:

DRIVE SHAFTS

Grease all universal joints and slipjoints until grease appears.

m

c...

~

Q

en Q I

I\)

EJ4060-2.doc

Page 2 of2

STANDARD TORQUE CHARTS AND CONVERSION TABLES This manual provides dual dimensioning for most specifications. U.S. standard units are specified first, with metric (SI) units in parentheses.

References throughout the manual to standard torques or other standard values will be to one of the following charts or tables. For values not shown in these charts or tables, standard conversion factors for most commonly used measurements are provided in TABLE XIII, page A5-6.

Standard torque values are not to be used when “turnof-the-nut” tightening procedures are recommended.

INDEX OF TABLES TABLE I . . . . . . . Standard Torque Chart (SAE) TABLE II . Standard Torque, 12-Point, Grade 9 TABLE III . . Standard Metric Assembly Torque TABLE IV . . . . . . JIC Swivel Nuts Torque Chart TABLE V . . . . . . . . .Pipe Thread Torque Chart TABLE VI . . . . . . . . O-Ring Boss Torque Chart TABLEVII . . . . O-Ring Face Seal Torque Chart TABLE VIII . Torque Conversions (ft lbs to N•m) TABLE IX . Torque Conversions (ft lbs to kg•m) TABLE X . . Pressure Conversions (psi to kPa) TABLE XI . Pressure Conversions (psi to MPa) TABLE XII . . . . . . . .Temperature Conversions TABLE XIII . . . Common Conversion Multipliers

Grade 5

Cap Screw Thread Size

kg•m

1/4-20

7

1/4-28

8

5/16-18

The Komatsu engineering department does not recommend the use of special friction-reducing lubricants, such as Copper Coat, Never-Seez®, and other similar products, on the threads of standard fasteners where standard torque values are applied.

The use of special friction-reducing lubricants will significantly alter the clamping force being applied to fasteners during the tightening process.

If special friction-reducing lubricants are used with the standard torque values listed below in Table I, excessive stress and possible breakage of the fasteners may result.

Where the torque tables specify “Lubricated Threads” for the standard torque values listed, these standard torque values are to be used with simple lithium base chassis grease (multi-purpose EP NLGI) or a rustpreventive grease (see list, page A5-2) on the threads and seats unless specified otherwise.

NOTE: Ensure the threads of fasteners and tapped holes are free of burrs and other imperfections before assembling.

TABLE I. -STANDARD TORQUE CHART SAE HEX HEAD CAP SCREW AND NUT ASSEMBLY (LUBRICATED THREADS) - TOLERANCES ±10%

TORQUE GRADE 5 ft lbs

. . A5-1 . . A5-2 . . A5-2 . . A5-3 . . A5-3 . . A5-3 . . A5-3 . . A5-4 . . A5-4 . . A5-4 . . A5-5 . . A5-5 . . A5-6

EFFECT OF SPECIAL LUBRICANTS On Fasteners and Standard Torque Values

TORQUE GRADE 8 N•m

Cap Screw Thread Size

Grade 8

TORQUE GRADE 5

TORQUE GRADE 8

N•m

ft lbs

kg•m

ft lbs

kg•m

N•m

ft lbs

kg•m

N•m

0.97

9.5

10

1.38

13.6

1.11

10.8

11

1.52

14.9

3/4-16

235

32.5

319

335

46.3

454

7/8-9

350

48.4

475

500

69.2

15

2.07

20.3

21

2.90

28

678

7/8-14

375

51.9

508

530

73.3

719

5/16-24

16

2.21

22

22

3.04

3/8-16

25

3.46

34

35

4.84

30

1.0-8

525

72.6

712

750

103.7

1017

47

1.0-12

560

77.4

759

790

109.3

3/8-24

30

4.15

41

40

1071

5.5

54

1.0-14

570

78.8

773

800

110.6

7/16-14

40

5.5

54

1085

58

8.0

79

1 1/8-7

650

89.9

881

1050

145

7/16-20

45

6.2

61

1424

62

8.57

84

1 1/8-12

700

96.8

949

1140

158

1546

1/2-13

65

9

88

90

12.4

122

1 1/4-7

910

125.9

1234

1480

205

2007

1/2-20

70

9.7

95

95

13.1

129

1 1/4-12

975

134.8

1322

1580

219

2142

9/16-12

90

12.4

122

125

17.3

169

1 3/8-6

1200

166

1627

1940

268

2630

9/16-18

95

13.1

129

135

18.7

183

1 3/8-12

1310

181

1776

2120

293

2874

5/8-11

125

17.3

169

175

24.2

237

1 1/2-6

1580

219

2142

2560

354

3471

5/8-18

135

18.7

183

190

26.2

258

1 1/2-12

1700

235

2305

2770

383

3756

3/4-10

220

30.4

298

310

42.8

420

1 ft lbs = 0.138 kg•m = 1.356 N•m

STANDARD ASSEMBLY TORQUES For 12-Point, Grade 9 Cap Screws (SAE)

STANDARD ASSEMBLY TORQUES For Class 10.9 Cap screws & Class 10 Nuts

The following specifications apply to required assembly torques for all 12-point, grade 9 (170,000 psi minimum tensile) cap screws.

The following specifications apply to required assembly torques for all metric Class 10.9 finished hexagon head cap screws and Class 10 nuts.

• Cap screw threads and seats shall be lubricated when assembled.

• Cap screw threads and seats shall not be lubricated when assembled. These specifications are based on all cap screws, nuts, and hardened washers being phosphate and oil coated.

NOTE: Unless the instructions specifically recommend otherwise, these standard torque values are to be used with simple lithium base chassis grease (multi-purpose EP NLGI) or a rust preventive grease (see list, this page) on the threads.

• Torques are calculated to give a clamping force of approximately 75% of proof load.

• The maximum torque tolerance shall be ±10% of the torque value shown.

NOTE: If zinc-plated hardware is used, each piece must be lubricated with simple lithium base chassis grease (multi-purpose EP NLGI) or a rust preventive grease (see list, this page) to achieve the same clamping forces provided below.

• Torques are calculated to give a clamping force of approximately 75% of proof load.

• The maximum torque tolerance shall be within ±10% of the torque value shown.

TABLE II. STANDARD ASSEMBLY TORQUE for 12-Point, Grade 9 Cap screws

TABLE III. STANDARD ASSEMBLY TORQUE for Metric Class 10.9 Cap screws & Class 10 Nuts

CAP SCREW SIZE*

TORQUE ft lbs

TORQUE N•m

TORQUE kg•m

0.250 - 20

12

16

1.7

0.312 - 18

24

33

3.3

M6 x1

12

9

1.22

0.375 - 16

42

57

5.8

M8 x 1.25

30

22

3.06

CAP SCREW SIZE*

TORQUE N•m

TORQUE ft lbs

TORQUE kg•m

0.438 -14

70

95

9.7

M10 x 1.5

55

40

5.61

0.500 -13

105

142

14.5

M12 x 1.75

95

70

9.69

0.562 - 12

150

203

20.7

M14 x 2

155

114

15.81

0.625 - 11

205

278

28.3

M16 x 2

240

177

24.48

0.750 - 10

360

488

49.7

M20 x 2.25

465

343

47.43

0.875 - 9

575

780

79.4

M24 x 3

800

590

81.6

1.000 - 8

860

1166

119

M30 x 3.5

1600

1180

163.2

1.000 - 12

915

1240

126

M36 x 4

2750

2028

280.5

1.125 - 7

1230

1670

170

* Shank Diameter (mm) - Threads per millimeter This table represents standard values only. Do not use these values to replace torque values which are specified in assembly instructions.

1.125 - 12

1330

1800

184

1.250 - 7

1715

2325

237

1.250 - 12

1840

2495

254

1.375 - 6

2270

3080

313

1.375 - 12

2475

3355

342

1.500 - 6

2980

4040

411

1.500 - 12

3225

4375

445

* Shank Diameter (in.) - Threads per inch This table represents standard values only. Do not use these values to replace torque values which are specified in assembly instructions.

Suggested* Sources for Rust Preventive Grease: • AMERICAN ANTI-RUST GREASE #3-X from Standard Oil Company (also American Oil Co.) • GULF NORUST #3 from Gulf Oil Company.

• MOBILARMA 355, Product No. 66705 from Mobil Oil Corporation.

• RUST BAN 326 from Humble Oil Company.

• RUSTOLENE B GREASE from Sinclair Oil Co. • RUST PREVENTIVE GREASE - CODE 312 from the Southwest Grease and Oil Company.

NOTE: This list represents the current engineering approved sources for use in Komatsu manufacture. It is not exclusive. Other products may meet the same specifications of this list.

TABLE IV. TORQUE CHART FOR JIC 37° SWIVEL NUTS WITH OR WITHOUT O-RING SEALS

TABLE VI. TORQUE CHART FOR O-RING BOSS FITTINGS

SIZE CODE

TUBE SIZE (O.D.)

THREADS UNF-2B

TORQUE ft lbs

SIZE CODE

TUBE SIZE (O.D.)

THREADS UNF-2B

TORQUE ft lbs

–2

0.125

0.312 – 24

4 ±1

–2

0.125

0.312 – 24

4 ±2

–3

0.188

0.375 – 24

8 ±3

–3

0.188

0.375 – 24

5 ±2

–4

0.250

0.438 – 20

12 ±3

–4

0.250

0.438 – 20

8 ±3

–5

0.312

0.500 – 20

15 ±3

–5

0.312

0.500 – 20

10 ±3

–6

0.375

0.562 – 18

18 ±5

–6

0.375

0.562 – 18

13 ±3

–8

0.500

0.750 – 16

30 ±5

–8

0.500

0.750 – 16

24 ±5

– 10

0.625

0.875 – 14

40 ±5

– 10

0.625

0.875 – 14

32 ±5

– 12

0.750

1.062 – 12

55 ±5

– 12

0.750

1.062 – 12

48 ±5

– 14

0.875

1.188 – 12

65 ±5

– 14

0.875

1.188 – 12

54 ±5

– 16

1.000

1.312 – 12

80 ±5

– 16

1.000

1.312 – 12

72 ±5

– 20

1.250

1.625 – 12

100 ±10

– 20

1.250

1.625 – 12

80 ±5

– 24

1.500

1.875 – 12

120 ±10

– 24

1.500

1.875 – 12

80 ±5

– 32

2.000

2.500 – 12

230 ±20

– 32

2.000

2.500 – 12

96 ±10

TABLE V. TORQUE CHART FOR PIPE THREAD FITTINGS

TABLE VII. TORQUE CHART FOR O-RING FACE SEAL FITTINGS

SIZE CODE

PIPE THREAD SIZE

WITH SEALANT ft lbs

WITHOUT SEALANT ft lbs

–2

0.125 – 27

15 ±3

20 ±5

–4

0.250 – 18

20 ±5

25 ±5

–6

0.375 – 18

25 ±5

35 ±5

–8

0.500 – 14

35 ±5

45 ±5

– 12

0.750 – 14

45 ±5

55 ±5

– 16

1.000 – 11.50

55 ±5

65 ±5

– 20

1.250 – 11.50

70 ±5

80 ±5

– 24

1.500 – 11.50

80 ±5

95 ±10

– 32

2.000 – 11.50

95 ±10

120 ±10

SIZE CODE

TUBE SIZE (O.D.)

THREADS UNF-2B

TORQUE ft lbs

–4

0.250

0.438 – 20

11 ±1

–6

0.375

0.562 – 18

18 ±2

–8

0.500

0.750 – 16

35 ±4

– 10

0.625

0.875 – 14

51 ±5

– 12

0.750

1.062 – 12

71 ±7

– 16

1.000

1.312 – 12

98 ±6

– 20

1.250

1.625 – 12

132 ±7

– 24

1.500

1.875 – 12

165 ±15

TABLE VIII. TORQUE CONVERSIONS Foot Pounds (ft lbs) to Newton-meters (N•m) ft lbs

0

1

2

3

4

5

6

7

8

9

0

(N.m)

1.36

2.71

4.07

5.42

6.78

8.14

9.49

10.85

12.20

10

13.56

14.91

16.27

17.63

18.98

20.34

21.69

23.05

24.40

25.76

20

27.12

28.47

29.83

31.18

32.54

33.90

35.25

36.61

37.96

39.32

30

40.67

42.03

43.39

44.74

46.10

47.45

48.81

50.17

51.52

52.87

40

54.23

55.59

56.94

58.30

59.66

60.01

62.37

63.72

65.08

66.44

50

67.79

69.15

70.50

71.86

73.21

74.57

75.93

77.28

78.64

80.00

60

81.35

82.70

84.06

85.42

86.77

88.13

89.48

90.84

92.20

93.55

70

94.91

96.26

97.62

98.97

100.33

101.69

103.04

104.40

105.75

107.11

80

108.47

109.82

111.18

112.53

113.89

115.24

116.60

117.96

119.31

120.67

90

122.03

123.38

124.74

126.09

127.45

128.80

130.16

131.51

132.87

134.23

See NOTE on page A5-5 regarding Table usage

TABLE IX. TORQUE CONVERSIONS Foot Pounds (ft lbs) to kilogram-meters (kg•m) ft lbs

0

1

2

3

4

5

6

7

8

9

0

(kg.m)

0.138

0.277

0.415

0.553

0.692

0.830

0.968

1.106

1.245

10

1.38

1.52

1.66

1.80

1.94

2.07

2.21

2.35

2.49

2.63

20

2.77

2.90

3.04

3.18

3.32

3.46

3.60

3.73

3.87

4.01

30

4.15

4.29

4.43

4.56

4.70

4.84

4.98

5.12

5.26

5.39

40

5.53

5.67

5.81

5.95

6.09

6.22

6.36

6.50

6.64

6.78

50

6.92

7.05

7.19

7.33

7.47

7.61

7.74

7.88

8.02

8.16

60

8.30

8.44

8.57

8.71

8.85

8.99

9.13

9.27

9.40

9.54

70

9.68

9.82

9.96

10.10

10.23

10.37

10.51

10.65

10.79

10.93

80

11.06

11.20

11.34

11.48

11.62

11.76

11.89

12.03

12.17

12.30

90

12.45

12.59

12.72

12.86

13.00

13.14

13.28

13.42

13.55

13.69

See NOTE on page A5-5 regarding Table usage

TABLE X. PRESSURE CONVERSIONS Pounds/square inch (psi) To Kilopascals (kPa) Formula: psi x 6.895 = kPa psi

0

1

2

3

4

5

6

7

8

9

0

(kPa)

6.895

13.79

20.68

27.58

34.47

41.37

48.26

55.16

62.05

10

68.95

75.84

82.74

89.63

96.53

103.42

110.32

117.21

124.1

131.0

20

137.9

144.8

151.7

158.6

165.5

172.4

179.3

186.2

193.1

200.0

30

206.8

213.7

220.6

227.5

234.4

241.3

248.2

255.1

262.0

268.9

40

275.8

282.7

289.6

296.5

303.4

310.3

317.2

324.1

331.0

337.9

50

344.7

351.6

358.5

365.4

372.3

379.2

386.1

393.0

399.9

406.8

60

413.7

420.6

427.5

434.4

441.3

448.2

455.1

462.0

468.9

475.8

70

482.6

489.5

496.4

503.3

510.2

517.1

524.0

530.9

537.8

544.7

80

551.6

558.5

565.4

572.3

579.2

586.1

593.0

599.9

606.8

613.7

90

620.5

627.4

634.3

641.2

648.1

655.0

661.9

668.8

675.7

682.6

See NOTE on page A5-5 regarding Table usage

TABLE XI. PRESSURE CONVERSIONS Pounds/square inch (psi) To Megapascals (MPa) Formula: psi x 0.0069 = MPa psi

0

10

20

30

40

50

60

70

80

90

0

(MPa)

0.069

0.14

0.21

0.28

0.34

0.41

0.48

0.55

0.62

100

0.69

0.76

0.83

0.90

0.97

1.03

1.10

1.17

1.24

1.31

200

1.38

1.45

1.52

1.59

1.65

1.72

1.79

1.86

1.93

2.00

300

2.07

2.14

2.21

2.28

2.34

2.41

2.48

2.55

2.62

2.69

400

2.76

2.83

2.90

2.96

3.03

3.10

3.17

3.24

3.31

3.38

500

3.45

3.52

3.59

3.65

3.72

3.79

3.86

3.93

4.00

4.07

600

4.14

4.21

4.27

4.34

4.41

4.48

4.55

4.62

4.69

4.76

700

4.83

4.90

4.96

5.03

5.10

5.17

5.24

5.31

5.38

5.45

800

5.52

5.58

5.65

5.72

5.79

5.86

5.93

6.00

6.07

6.14

900

6.21

6.27

6.34

6.41

6.48

6.55

6.62

6.69

6.76

6.83

See NOTE below regarding Table usage

NOTE: Tables such as Table VIII, IX, X, and XI may be used as in the following example: Example: Convert 975 psi to kilopascals (kPa).

1. Select Table X. 2. Go to psi row 90, column 7; read 668.8 97 psi = 668.8 kPa.

3. Multiply by 10: 970 psi = 6688 kPa. 4. Go to psi row 0, column 5; read 34.475 psi = 34.47 kPa. Add to step 3.

5. 970 + 5 psi = 6688 + 34 = 6722 kPa.

TABLE XII. TEMPERATURE CONVERSIONS Formula: F° - 32 / 1.8 = C° or C° x 1.8 + 32 = F° CELSIUS FAHRENHEIT CELSIUS FAHRENHEIT CELSIUS FAHRENHEIT C° F° C° F° C° F° 121 250 482 63 145 293 4 40 104 118 245 473 60 140 284 2 35 95 116 240 464 57 135 275 –1 30 86 113 235 455 54 130 266 –4 25 77 110 230 446 52 125 257 –7 20 68 107 225 437 49 120 248 –9 15 59 104 220 428 46 115 239 – 12 10 50 102 215 419 43 110 230 – 15 5 41 99 210 410 41 105 221 – 18 0 32 96 205 401 38 100 212 – 21 –5 23 93 200 392 35 95 293 – 23 – 10 14 91 195 383 32 90 194 – 26 – 15 5 88 190 374 29 85 185 – 29 – 20 –4 85 185 365 27 80 176 – 32 – 25 – 13 82 180 356 24 75 167 – 34 – 30 – 22 79 175 347 21 70 158 – 37 – 35 – 31 77 170 338 18 65 149 – 40 – 40 – 40 74 165 329 15 60 140 – 43 – 45 – 49 71 160 320 13 55 131 – 46 – 50 – 58 68 155 311 10 50 122 – 48 – 55 – 67 66 150 302 7 45 113 – 51 – 60 – 76 NOTE: The numbers in the unmarked columns refer to temperature in either degrees Celsius (C°) or Fahrenheit (F°). Select a number in this unmarked column and read to the left to convert to degrees Celsius (C°) or read to the right to convert to degrees Fahrenheit (F°). If starting with a known temperature (either C° or F°), find that temperature in the marked column and read the converted temperature in the center, unmarked column.

TABLE XIII COMMON CONVERSION MULTIPLIERS

COMMON CONVERSION MULTIPLIERS METRIC TO ENGLISH

COMMON CONVERSION MULTIPLIERS ENGLISH TO METRIC

Multiply By

TO

Multiply By

inch – in.

millimeter (mm)

25.40

millimeter (mm)

inch – in.

0.0394

inch – in.

centimeter (cm)

2.54

centimeter (cm)

inch – in.

0.3937

foot – ft

meter (m)

0.3048

meter (m)

foot – ft

3.2808

yard – yd

meter (m)

0.914

meter (m)

yard – yd

1.0936

1.61

kilometer (km)

mile – mi.

0.6210

To Convert From

mile – mi.

kilometer (km)

To Convert From

2)

TO

in.2

0.1550

sq. centimeters (cm )

6.45

sq. centimeters (cm

sq. ft. – ft2

sq. centimeters (cm2)

929

sq. centimeters (cm2)

sq. ft. – ft2

0.001

cu. in. – in.3

cu. centimeters (cm3)

16.39

cu. centimeters (cm3)

cu in – in.3

0.061

cu. in. – in.3

liters (l)

0.016

liters (l)

cu in – in.3

61.02

cu. ft. – ft3

cu. meters (m3)

0.028

cu. meters (m3)

cu ft – ft3

35.314

cu. ft. – ft3

liters (l)

28.3

liters (l)

cu ft – ft3

0.0353

ounce – oz

kilogram (kg)

0.028

grams (g)

ounce – oz.

0.0353

fluid ounce – fl oz

milliliter (ml)

29.573

milliliter (ml)

fluid ounce – fl oz.

0.0338

pound (mass)

kilogram (kg)

0.454

kilogram (kg)

pound (mass)

2.2046

Newton (N)

4.448

Newton (N)

pound (force) – lbs

0.2248

Newton meters (N•m)

0.113

Newton-meters (N•m)

kilogram meters (kg•m)

0.102

sq. in. – in.

2

pound (force) – lbs in. lbs. (force)

2

sq. in. –

ft lbs (force)

Newton meters (N•m)

1.356

Newton-meters (N.m)

ft lbs

0.7376

ft lbs (force)

kilogram meters (kg•m)

0.138

kilogram-meters (kg•m)

ft lbs

7.2329

psi (pressure)

kilopascals (kPa)

6.895

kilogram-meters (kg•m)

Newton meters (N•m)

9.807

psi (pressure)

megapascals (MPa)

0.007

kilopascals (kPa)

psi

0.1450

psi (pressure)

kilograms/cm2 (kg/cm2)

0.0704

megapascals (MPa)

psi

145.038

psi

14.2231

kilopascals (kPa)

98.068

ton

0.0011

2

(kg/cm2)

ton (short)

kilogram (kg)

907.2

kilograms/cm

ton (short)

metric ton

0.0907

kilograms/cm2 (kg/cm2)

quart – qt

liters (l)

0.946

kilogram (kg)

gallon – gal

liters (l)

3.785

metric ton

HP (horsepower)

Watts

745.7

liters (l)

HP (horsepower)

kilowatts (kw)

0.745

liters (l)

ton

1.1023

quart – qt

1.0567

gallon – gal

0.2642

Watts

Horsepower HP

0.00134

kilowatts (kw)

Horsepower HP

1.3410

FIELD ASSEMBLY INSPECTION REPORT After completion of assembling a machine, make inspections according to these check sheets for assuring machine performance and quality.

MACHINE MODEL MACHINE SERIAL NUMBER

(Circle One) 730E 830E

830E-1AC

930E-4

930E-4SE

Service Meter Reading

Date of Inspection

ENGINE MODEL

CUSTOMER UNIT NUMBER

Wheel Motor Serial Numbers

Location of Machine at Inspection

ENGINE SERIAL NUMBER

LH

Dump Body Manufacturer Komatsu

RH Other

Distributor’s Name

Dump Body Style

Customer’s Name

KAC Area Service Manager Signature

Date

Customer’s Address

Inspector’s Comments:

Inspector’s Name

KOMATSU USE ONLY: Sheet receiving Date:

Title

By:

Signature

Remark:

Submitting of this report (and check sheets) to Komatsu is one of the conditions of warranty validation.

All four copies are to be distributed as shown below.

Send White Reports to

Manager of Technical Support Komatsu America Corp.

2300 N.E. Adams St, P.O. Box 240 Peoria, IL 61650-0240 U.S.A.

Send Canary Reports to

Manager of Field Assembly Komatsu America Corp.

2300 N.E. Adams St, P.O. Box 240 Peoria, IL 61650-0240 U.S.A.

Send Pink Reports to your KAC Regional Service Manager Send Gold Reports to the Service Manager at the KAC Distributor who sold the truck.

Mark each item with the appropriate symbol as shown below.

CEAW003212

White - Komatsu, Manager of Technical Support Canary - Komatsu, Manager of Field Assembly Pink - Komatsu, Regional Service Manager Gold - Komatsu Distributor, Service Manager

Page 1 of 5

Acceptance Procedures

Maintenance

Inspection Item

Accepted

No.

Inspection Around Machine 1

Parts

Visual inspection of unit for loose parts and debris

2

Hardware

Visual inspection of unit for missing and/or loose mounting hardware

3

Hoses and Cables

Visual inspection of hydraulic hoses and electric cables to ensure they are securely clamped and clear from sharp edges and not rubbing each other

4

Ground Straps

Verify all ground straps are secure (sub frame, anchor etc.)

5

Engine Oil Level

Verify engine oil level is in operating range

6

Engine Fan

Inspect fan-to-shroud clearance and belt alignment

7

Hydraulic Oil Level

Oil level visible through the upper sight glass with body down

8

Hatch Door (730E, 830E, 830E-1AC)

Verify adequate latch seal on the rear axle hatch door to prevent dust entry

9

Anchor Pin

Visually inspect anchor hitch pin and anti-sway bar assembly for proper assembly and properly tightened hardware

10

Wheel Motors

Inspect oil specification and proper oil level

11

Fuel Tank

Verify fuel tank mounting is secure and there are no fuel leaks

12

Radiator

Inspect coolant fill level, cold temperature protection, and DCA additive

13

Decks and Ladders

Inspect all ladders and handrails are secure and hardware is tight Visual inspection of installation of grid blower, rectifier assembly and control box for correct assembly of components and proper clamping, no loose contacts, no damaged or poorly crimped cables

14

Battery

Inspect all wiring and connections in battery box - no rubbing or chafing Verify battery mounting hardware is secure Verify electrolyte at proper level and caps are securely installed Verify all battery terminals are secure

15

Frame

Visually inspect installation of steering cylinders, tie rod, and accumulators per print Visually inspect hoist valve, pumps, filters, hydraulic tank and hoist cylinder installations (all hardware secure, no leaks)

Hardware Torque 1

Suspension

2

Wheels

Verify front suspension mounting cap screws have been properly tightened per appropriate service manual procedure using the “turn-of-the-nut” method 730E

Verify torque on all wedge nuts at 746 N·m (550 ft lbs)

(See Note below chart) 830E, 830E-1AC

Verify torque on all wedge nuts at 746 N·m (550 ft lbs)

(See Note below chart) 930E-4, 930E-4SE (See Note below chart)

Verify torque on front wheel nuts at 2 326 ± 136 N·m (1715 ± 100 ft lbs) Verify torque on rear inside wheel nuts at 2 326 ± 136 N·m (1715 ± 100 ft lbs) Verify torque on rear outside wheel nuts and adapter ring at 2326 ± 136 N·m (1715 ± 100 ft lbs)

3

Rops

Verify torque on left rops beam cap screws at 949 N·m (700 ft lbs) Verify torque on right cross beam cap screws at 240 N·m (177 ft lbs)

4

Cab

Verify torque on cab mounting cap screws at 949 N·m (700 ft lbs)

5

Wheel Motor

Verify torque on wheel motor mounting cap screws at 2 007 N·m (1480 ft lbs)

NOTE: Refer to Section G, Tires and Rims, in the appropriate service manual for the complete wheel mounting tightening procedure.

CEAW003212

White - Komatsu, Manager of Technical Support Canary - Komatsu, Manager of Field Assembly Pink - Komatsu, Regional Service Manager Gold - Komatsu Distributor, Service Manager

Page 2 of 5

Acceptance Procedures

Maintenance

Inspection Item

Accepted

No.

Cab Compartment 1

Cab Doors

Verify doors open and close smoothly, latch works properly, O&M manual in door

2

Cab Windows

Verify windows can be opened and closed smoothly

3

Door Locks

Verify left and right door locks work properly with key

4

Interior

Visually inspect interior for completeness of assembly

5

Cab Seats

Inspect operators seat adjustments (slide lever, back rest operation, seat inclination, seat height etc.)

Visually inspect for cracked glass, torn upholstery, dirt, stains, holes etc.

Inspect seat belt for proper installation (and seat tethers) 6

Passenger Seat

Verify back rest operates without interference

7

Steering Wheel

Check tilt and telescoping functions

8

Wiper

Verify wiper works all speeds, & range does not extend beyond glass surface

9

Cigarette Lighter

Check lighter operation, should pop up after 10 seconds and be hot (730E,830E only)

10

Horn

Check for proper sound, no looseness in horn button

11

Back Up Horn

Check for proper sound, and function

12

Shift Tower

Check for proper function, no binding or looseness

13

Gauges

Verify gauges are installed straight and operating correctly

14

Hydraulic Fittings

Visually inspect all hydraulic fittings in front of cab, rear of cab, and hydraulic brake cabinet

15

Hoist

Check operation of the hoist lever in all four positions

Headlights

Verify all headlights working, high and low beams

Check adjustable lever can be locked securely

Verify the windshield washer works properly and washer fluid bottle is full

Lights 1

Verify high beam indicators are functional Verify lights at proper angle 2

Instrument Panel

Check switch depresses and all lights function

2a

Dimmer Switch

Verify dimmer operates properly

2b

Turn Signal

Visually inspect front and rear turn signal operation on left and right sides Directional indicators operate properly Switch turns off after turn is completed

3

Hazard Flashers

Verify flasher operates properly

4

Back Up Light

Verify back up light operates properly when shifter is in R position

5

Manual Back Up Light

Verify switch and light work properly

6

Fog Light (optional)

Verify fog lights and indicator lights operating properly

Verify hazard indicator lights operating properly

Brake Lights 1

Service Brake

2

Brake Lock

Verify brake lock light operating properly

3

Emergency Brake

Verify emergency brake light operating properly

4

Parking Brake

Verified parking brake light operating properly

5

Dome Light

Verify dome light is on when the switch is ON

6

Retarder Lights

Verify retard light operating properly

CEAW003212

Verify service brake lights operating properly

White - Komatsu, Manager of Technical Support Canary - Komatsu, Manager of Field Assembly Pink - Komatsu, Regional Service Manager Gold - Komatsu Distributor, Service Manager

Page 3 of 5

Acceptance Procedures

Maintenance

Inspection Item

Accepted

No.

Service Inspection 1

Suspension

730E

(See Note below chart)

Suspension oiling height, 38.1 mm (1.5 in.) front and 72.6 mm (2.9 in.) rear Front charge height, 229 mm (9 in.) at 2758 kPa (400 psi) Rear charge height, 276 mm (10.9 in. ) at 1420 kPa (206 psi)

830E, 830E-1AC (See Note below chart)

Suspension oiling height, 25.4 mm (1 in.) front and 25.4 mm (1 in.) rear Front charge height, 229 mm (9 in.) at 2689 kPa (390 psi) Rear charge height, 241 mm (9.5 in.) at 1724 kPa (250 psi)

930E-4, 930E-4SE (See Note below chart)

Suspension oiling height at 25.4 mm (1 in.) front and 53.0 mm (2.1 in.) rear Front charge height, 229 mm (9 in.) at 2930 kPa (425 psi) Rear charge height, 218 mm (8.6 in.) at 1482 kPa (215 psi)

2

Accumulators

Verify nitrogen charge in accumulators is at 9 653 kPa (1400 psi) for all models, for both steering and brakes (charge pressure will vary with ambient temperature, refer to chart in SM)

3

Engine Prelube

If equipped, ensure prelube is working prior to engine starting

4

Engine Starting

Ensure engine starts easily

5

Engine Noise

No abnormal noise from engine

6

Brake Lock

Verify when switch is ON, brakes are applied and light is illuminated. Must be in Neutral.

7a

Parking Brake

Verify when switch is ON, brakes are applied and light is illuminated

730E, 830E 7b 8

830E-1AC, 930E-4, 930E-4SE Brake Pressure

730E

Verify when directional control lever is in PARK, brakes are applied and light is illuminated Verify with pedal depressed, front brake pressure is 17 236 ± 689 kPa (2500 ± 100 psi) Verify with pedal depressed, rear brake pressure is 11 721 ± 517 kPa (1700 ± 75 psi) Verify brake lock pressure is 10 342 ± 689 kPa (1500 ± 100 psi) Verify parking brake pressure is 17 926 ± 689 kPa (2600 ± 100 psi)

830E, 830E-1AC

Verify with pedal depressed, front brake pressure is 20 684 ± 1034 kPa (3000 ± 150 psi) Verify with pedal depressed, rear brake pressure is 13 652 ± 689 kPa (1980 ± 100 psi) (830E) or 10 894 ± 517 kPa (1580 ± 75 psi) (830E-1AC) Verify brake lock pressure is 10 342 ± 689 kPa (1500 ± 100 psi) Verify parking brake pressure is 17 236 ± 689 kPa (2500 ± 100 psi)

930E-4, 930E-4SE

Verify with pedal depressed, front brake pressure (BF) is 17 236 ± 517 kPa (2500 ± 75 psi) Verify with pedal depressed, rear brake pressure (BR) is 17 236 ± 517 kPa (2500 ± 75 psi) Verify brake lock pressure is 13 790 ± 689 kPa (2000 ± 100 psi) Verify parking brake release pressure is 18 616 ± 689 kPa (2700 ± 100 psi)

9

Steering

Verify that steering system is operating smoothly, turning from lock to lock

10

Hoist

Verify hoist pressure is 17 236 kPa (2500 psi) power up, and 10 342 kPa (1500 psi) power down

Verify steering system is free of noise and vibration

Verify hoist limit switch is operational and is set correctly (measure on the hoist cylinder - 3rd stage), cylinder should stop 6 inches before full extension Verify that the hoist hold position operates properly Verify that there is no heavy shock when the body returns to the frame in float

NOTE: Refer to Section H, Oiling and Charging Procedure, in the appropriate service manual for complete suspension oiling and charging instructions.

CEAW003212

White - Komatsu, Manager of Technical Support Canary - Komatsu, Manager of Field Assembly Pink - Komatsu, Regional Service Manager Gold - Komatsu Distributor, Service Manager

Page 4 of 5

11

730E

Acceptance Procedures

Maintenance

Inspection Item Hoist Times

Accepted

No.

Power up loaded - 21-23 seconds Power down - 15-17 seconds Float down empty - 22-24 seconds

830E, 830E-1AC

Power up loaded - 25-27 seconds Power down - 15-17 seconds Float down empty - 23-25 seconds

930E-4, 930E-4SE

Power up loaded - 21-23 seconds Power down - 23-25 seconds Float down empty - 24-26 seconds

All Trucks

Ensure body up switch activates the body up alarm and light in the cab

12

Lubrication

Ensure automatic lube system is serviced and full (and air bled from system)

13

Payload Meter Sys.

Calibrate and check payload meter operation per O&M manual

Ensure automatic lube system is operating properly and timer is set as desired

14

Error Codes

Troubleshoot any error codes and delete

15

Machine

Record machine model-type, machine serial number and engine serial number

16

Dump Body

Ensure the dump body is shimmed correctly prior to truck release

17

Electrical Checks

Ensure the electrical checkout procedure has been completed and signed off on, including megger testing (see appropriate Field Assembly Manual or Shop Manual for procedure)

18

Truck Programming

Ensure the truck is programed with itâ&#x20AC;&#x2122;s own unique configuration file and a copy of the file saved

ADDITIONAL COMMENTS__________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________

CEAW003212

White - Komatsu, Manager of Technical Support Canary - Komatsu, Manager of Field Assembly Pink - Komatsu, Regional Service Manager Gold - Komatsu Distributor, Service Manager

Page 5 of 5

50 HOUR POST-COMMISSIONING CHECKSHEET Make inspections according to this checksheet 50 hours (SMR) after the commissioning of a new truck to ensure machine performance and quality.

MACHINE MODEL MACHINE SERIAL NUMBER

(Circle One) 730E 830E

ENGINE MODEL

ENGINE SERIAL NUMBER

CUSTOMER UNIT NUMBER

830E1-AC

930E-4

930E-4SE

Service Meter Reading

Date of Inspection

Wheel Motor Serial Numbers

Location of Machine at Inspection

LH

Dump Body Manufacturer Komatsu

RH Other

Distributor’s Name

Dump Body Style

Customer’s Name

KAC Area Service Manager Signature

Date

Customer’s Address

Inspector’s Comments:

Inspector’s Name

KOMATSU USE ONLY: Sheet receiving Date:

Title

By:

Signature

Remark:

Send white reports to:

Manager of Technical Support Komatsu America Corp.

2300 N.E. Adams St., P.O. Box 240 Peoria, IL 61650-0240 U.S.A.

Send canary reports to:

Manager of Field Assembly Komatsu America Corp.

2300 N.E. Adams St., P.O. Box 240 Peoria, IL 61650-0240 U.S.A.

Send pink reports to your KAC Regional Service Manager Send gold reports to the Service Manager at the KAC Distributor who sold the truck

CEAW004203

White - Komatsu, Manager of Technical Support Canary - Komatsu, Manager of Field Assembly Pink - Komatsu, Regional Service Manager Gold - Komatsu Distributor, Service Manager

Page 1 of 5

No.

Inspection Item

Acceptance Procedures

As Found Condition

Corrective Action

Inspection Around Machine 1

Parts

Visually inspect the truck for loose parts and debris.

2

Hardware

Visually inspect the truck for missing and/or loose mounting hardware.

3

Hoses and Cables

Visually inspect hydraulic hoses and electric cables to ensure they are securely clamped and clear of sharp edges and other objects that may cause chaffing.

4

Engine Oil Level

Verify the engine oil level is at the proper operating range.

5

Hydraulic Oil Level

Verify the oil level is visible through the upper sight glass with the body down.

6

Anchor Pin

Visually inspect the anchor hitch pin and anti-sway bar assembly for proper installation and properly tightened hardware.

7

Wheel Motors

Verify the correct oil is being used and oil is at the proper level.

8

Fuel Tank

Verify the fuel tank mounting is secure and there are no fuel leaks.

9

Radiator

Inspect the coolant fill level, cold temperature protection, and DCA additive.

10

Steering Components

Verify proper installation of the steering cylinders, tie rod, and accumulators.

11

Hydraulic Components

Visually inspect the hoist valve, pumps, filters, hydraulic tank and hoist cylinder installations. All hardware must be secure, and no leaks evident.

12

Leakage

Visually inspect the entire machine for leaks.

Hardware Torque 1

Steering Arm To Suspension

730E - Verify hardware torque Target: 2705 N·m (1995 ft lbs) 830E, 830E-1AC- Verify hardware torque Target: 2705 N·m (1995 ft lbs) 930E-4, 930E-4SE - Verify hardware torque Target: 2705 N·m (1995 ft lbs)

2

Steering Cylinder To Frame

730E - Verify hardware torque Target: 464 N·m (342 ft lbs) 830E, 830E-1AC - Verify hardware torque Target: 712 N·m (525 ft lbs) 930E-4, 930E-4SE - Verify hardware torque Target: 1017 N·m (750 ft lbs)

3

Steering Cylinder To Steering Arm

730E - Verify hardware torque Target: 464 N·m (342 ft lbs) 830E, 830E-1AC - Verify hardware torque Target: 712 N·m (525 ft lbs) 930E-4, 930E-4SE - Verify hardware torque Target: 1017 N·m (750 ft lbs)

CEAW004203

White - Komatsu, Manager of Technical Support Canary - Komatsu, Manager of Field Assembly Pink - Komatsu, Regional Service Manager Gold - Komatsu Distributor, Service Manager

Page 2 of 5

No.

Inspection Item

Acceptance Procedures

4

Tie Rod Pin Retainer

730E - Verify hardware torque -

As Found Condition

Corrective Action

Target: 464 N·m (342 ft lbs) 830E, 830E-1AC - Verify hardware torque Target: 712 N·m (525 ft lbs) 930E-4, 930E-4SE - Verify hardware torque Target: 1017 N·m (750 ft lbs) 5

Front Brake Caliper Mounting

730E - Verify hardware torque -

(Capscrew with Nut)

830E, 830E-1AC - Verify hardware torque -

Target: 1085 N·m (800 ft lbs) Target: 1085 N·m (800 ft lbs)

6

Front Brake Caliper Mounting (Capscrew Only)

730E - Verify hardware torque Target: 1166 N·m (860 ft lbs) 830E, 830E-1AC - Verify hardware torque Target: 1166 N·m (860 ft lbs)

7

Rear Service Brake Caliper Mounting

730E - Verify hardware torque Target: 780 N·m (575 ft lbs) 830E, 830E-1AC - Verify hardware torque Target: 780 N·m (575 ft lbs)

8

Rear Brake Adapter Mounting

730E - Verify hardware torque Target: 488 N·m (360 ft lbs) 830E, 830E-1AC - Verify hardware torque Target: 488 N·m (360 ft lbs)

9

Brake Disc To Adapter Mounting

730E - Verify hardware torque Target: 278 N·m (205 ft lbs) 830E, 830E-1AC - Verify hardware torque Target: 278 N·m (205 ft lbs)

Cab Compartment 1

Horn

Check for proper tone and volume. Ensure there is no looseness in the horn button.

2

Back Up Horn

Check for proper tone, volume, and function.

3

Gauges

Verify all gauges are installed straight and are operating correctly.

4

Glass

Verify no cracks exist on cab windows. Ensure all windows are properly sealed.

5

Seat/Seat belts

Verify the cab seats and seat belts are in proper working condition.

CEAW004203

White - Komatsu, Manager of Technical Support Canary - Komatsu, Manager of Field Assembly Pink - Komatsu, Regional Service Manager Gold - Komatsu Distributor, Service Manager

Page 3 of 5

No.

Inspection Item

Acceptance Procedures

As Found Condition

Corrective Action

Service Inspection 1

Suspension

730E

(See Note below)

Suspension oiling height: 38.1 mm (1.5 in.) front and 72.6 mm (2.9 in.) rear Front charge height: 229 mm (9 in.) at 2758 kPa (400 psi) Rear charge height: 276 mm (10.9 in.) at 1420 kPa (206 psi)

830E, 830E-1AC (See Note below)

Suspension oiling height: 25.4 mm (1 in.) front and 25.4 mm (1 in.) rear Front charge height: 229 mm (9 in.) at 2689 kPa (390 psi) Rear charge height: 241 mm (9.5 in.) at 1724 kPa (250 psi)

930E-4, 930E-4SE (See Note below)

Suspension oiling height: 25.4 mm (1 in.) front and 53.0 mm (2.1 in.) rear Front charge height: 229 mm (9 in.) at 2930 kPa (425 psi) Rear charge height: 218 mm (8.6 in.) at 1482 kPa (215 psi)

NOTE: Refer to Section H, Oiling and Charging Procedure, in the appropriate service manual for complete suspension oiling and charging instructions.

2

Accumulators

Verify the nitrogen charge in the accumulators is at 9653 kPa (1400 psi) for all models, for both steering and brakes. (Charge pressure will vary with ambient temperature, refer to chart in SM)

3

Steering

Verify that steering system is operating smoothly while turning from lock to lock.

4

Lubrication

Verify the steering system is free of noise and vibration.

Ensure the automatic lube system contains no air and is filled to the proper level.

Ensure the automatic lube system is operating properly and the timer is set as desired.

5

Hydraulic Filters

Verify the 50 hour change of all hydraulic filters has been completed.

NOTE: Elements are supplied from the factory in the parts crate.

6

Tires

Check and record the tire pressure/size/manufacturer for future reference

Pressure Size Manufacturer

7

Payload Meter System

Calibrate and check payload meter operation per O&M manual. Troubleshoot any error codes and delete after repair.

8

GE Drive/Control System

Check drive control system operation per O&M manual.

Troubleshoot, correct and delete any error codes.

9

GE Rotating

Visually inspect wheel motor armature condition - brush wear, commutator color, etc.

Components (Wheel Motors, MTA, Grid Blower)

Inspect MTA slip rings and brushes.

10

Wheel Motor Sun Pinion End Play

Measure and record sun pinion end play for both RH and LH wheel motors

11

VHMS

Verify the VHMS system is functioning properly per O&M manual. Troubleshoot and repair any problems.

CEAW004203

Inspect grid blower motor commutator condition, brush wear, etc.

White - Komatsu, Manager of Technical Support Canary - Komatsu, Manager of Field Assembly Pink - Komatsu, Regional Service Manager Gold - Komatsu Distributor, Service Manager

Page 4 of 5

MINE OPTIONS - List any mine/site specific options or modifications made to the unit.

No.

Description of Modification

Reason For Installation

1 2 3 4 5 6

ADDITIONAL COMMENTS:______________________________________________________________

__________________________________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________

CEAW004203

White - Komatsu, Manager of Technical Support Canary - Komatsu, Manager of Field Assembly Pink - Komatsu, Regional Service Manager Gold - Komatsu Distributor, Service Manager

Page 5 of 5

®

www.komatsuamerica.com

Komatsu America Corp.

2300 N.E. Adams Street Peoria, IL 61639 Phone: 309-672-7577 Fax: 309-672-7072

Copyright 2010 Komatsu Printed in U.S.A.