John Deere 6110R, 6120R, 6130R, 6135R, 6145R, 6155R, 6175R Installation Instructions Manual MHM1870

Attachment - GreenStar™ Ready BL16445, BL16446, and BL16447

INSTALLATION INSTRUCTIONS MHM1870 04MAY20

(ENGLISCH)

6110R, 6120R, 6130R, 6135R, 6145R, 6155R, 6175R, 6195R, and 6215R (MY19)

John Deere GmbH & Co. KG John Deere Werk Mannheim MHM1870 (04MAY20) PRINTED IN U.S.A. COPYRIGHT © 2020 John Deere GmbH & Co. KG Mannheim Regional Center Zentralfunktionen All rights reserved.

A John Deere ILLUSTRUCTION ™ Manual Previous Editions Copyright © 2019 MHM1870-19-04MAY20

BL16445, BL16446, and BL16447

Check Status of Installation Instructions

the Installation Instructions available in the Technical Information Store. See https://techpubs.deere.com.

IMPORTANT: Before starting installation work, check if there is a newer version of

AK53658,0000CB6 -19-23AUG19-1/1

Recognize Safety Information This is a safety-alert symbol. When you see this symbol on your machine or in this manual, be alert to the potential for personal injury.

T81389 —UN—28JUN13

Follow recommended precautions and safe operating practices.

DX,ALERT -19-29SEP98-1/1

Understand Signal Words DANGER; The signal word DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury.

TS187 —19—30SEP88

WARNING; The signal word WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION; The signal word CAUTION indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. CAUTION may also be used to alert against unsafe practices associated with events which could lead to personal injury.

A signal word—DANGER, WARNING, or CAUTION—is used with the safety-alert symbol. DANGER identifies the most serious hazards. DANGER or WARNING safety signs are located near specific hazards. General

precautions are listed on CAUTION safety signs.

CAUTION also calls attention to safety messages in this manual.

DX,SIGNAL -19-05OCT16-1/1

Carefully read all safety messages in this instruction. Read the product operators manual for operating instructions and safety messages. Do not let anyone operate without instruction. (A copy of the operators manual may also be available from the Service ADVISOR™ application.)

TS201 —UN—15APR13

Follow Safety Instructions

Service ADVISOR is a trademark of Deere & Company DX,READ,INS -19-23JUN09-1/1

MHM1870 (04MAY20)

1

060220

PN=3

BL16445, BL16446, and BL16447

Park Machine Safely Before working on the machine:

TS230 —UN—24MAY89

• Lower all equipment to the ground.

• Stop the engine and remove the key.

• Disconnect the battery ground strap.

• Hang a "DO NOT OPERATE" tag in operator station.

DX,PARK -19-04JUN90-1/1

Overview of Trademarks Custom Performance™

Trademark of Deere & Company

GreenStar™

Trademark of Deere & Company

JDLink™

Trademark of Deere & Company

Service ADVISOR™

Trademark of Deere & Company

Software Server

John Deere Custom Performance software delivery system OUCC002,0006344 -19-30DEC19-1/1

General Information CAUTION: When performing the work described below, comply with the safety instructions in the relevant technical manuals.

NOTE: For related work, refer to the relevant Technical Manual.

NOTE: If torques for screws and screw fittings are not specified here, refer to the relevant Repair Technical Manual.

NOTE: Due to the variety of tractor types and materials used, it is not possible to describe and illustrate all the different methods of installation in these installation instructions.

AK53658,0000AC6 -19-09MAY18-1/1

Disconnect Battery

LX000872 —UN—19SEP94

CAUTION: Disconnect the negative terminal first. When reconnecting, do the positive terminal first. Always pay attention to the positive/negative markings on the battery.

CAUTION: Comply with safety instructions on how to handle batteries. See Technical Manual, Section 05.

LX23682,0000BD7 -19-24AUG17-1/1

MHM1870 (04MAY20)

2

060220

PN=4

BL16445, BL16446, and BL16447

Model Year (MY) Information on Serial Numbers and Model Identification

tractors accordingly, characteristics were defined for each model year (MY). Information on serial numbers and the identification of the various model years (MY) are described in the respective technical manuals.

Changes are made several times to tractors during ongoing production. In order to be able to identify

LX25500,00008D3 -19-13SEP18-1/1

Summary of Attachments Attachment

Designation

Tractors

Model Year

BL16445

Attachment -GreenStar™ Ready (ISOBUS Power Harness)

6110R, 6120R, 6130R, 6135R, 6145R, 6155R, 6175R, 6195R, 6215R

MY19 Tractors

BL16446

Attachment -GreenStar™ Ready (Tractor with Standard Cab Roof)

6110R, 6120R, 6130R, 6135R, 6145R, 6155R, 6175R, 6195R, 6215R

MY19 Tractors

BL16447

Attachment -GreenStar™ Ready (Tractor with Panoramic Cab Roof)

6110R, 6120R, 6130R, 6135R, 6145R, 6155R, 6175R, 6195R, 6215R

MY19 Tractors

OUCC002,000634A -19-05MAY20-1/1

Overview of Additional Parts That Are Required NOTE: The parts listed are not included in the scope of supply; if necessary, they must be ordered separately through normal parts channels.

Extra Parts Required for Attachment BL16446 and BL16447 Part Number.

L210203

Designation

Tractors

Quantity

Clamp

6110R, 6120R, 6130R, 6135R, 6145R, 6155R, 6175R, 6195R, 6215R

1

OUCC002,0006341 -19-30DEC19-1/1

MHM1870 (04MAY20)

3

060220

PN=5

BL16445, BL16446, and BL16447

Install Attachment—Cab Roof Wiring Harness

ZX209685 —UN—24FEB14

CAUTION: Read and understand the Handle Electronic Components and Brackets Safely section before accessing cab roof.

NOTE: Preparation and removal of parts processes are described from steps 1 to 8.

To install cab roof wiring harness, prepare the tractor as follows: 1. Remove outer cab roof (A). If the cab is equipped with a top roof window:

b. Remove the latching device cover (C) from the inside of the cab. c. Remove all socket-head fixing screws (D) all locking device frame (E). d. Remove window assembly (F) from cab roof.

D—Socket-Head Screw E—Frame F— Window Assembly

ZX209683 —UN—24FEB14

ZX209682 —UN—24FEB14

A—Outer Cab Roof B—Handle C—Cover

ZX209681 —UN—24FEB14

a. Unlatch handle (B) of latching device.

Continued on next page

MHM1870 (04MAY20)

4

OUCC002,0006343 -19-30DEC19-1/18

060220

PN=6

ZX209686 —UN—24FEB14

ZX209684 —UN—24FEB14

BL16445, BL16446, and BL16447

2. Remove all outer cab roof fixing screws (see arrows).

ZX209687 —UN—24FEB14

NOTE: On the North American tractors cab only, it is necessary to detach outer rear cab lights from their cover to access cab roof fixing screws.

3. Remove outer cab roof (A).

LX398410 —UN—30DEC19

A—Outer Cab Roof

ZX209688 —UN—24FEB14

North American Tractor Cab Only

Continued on next page

MHM1870 (04MAY20)

5

OUCC002,0006343 -19-30DEC19-2/18

060220

PN=7

BL16445, BL16446, and BL16447

4. Remove C—post upper panel (A).

ZX210627 —UN—09APR14

A— C—Post Upper Panel

Continued on next page

MHM1870 (04MAY20)

6

OUCC002,0006343 -19-30DEC19-3/18

060220

PN=8

BL16445, BL16446, and BL16447

5. Remove bottle holder assembly (A), cover (B), then A-post panel (C).

6. Remove the in cab mirror (D) from the cab roof (E) and the roof box assembly (F).

D—In Cab Mirror E—Cab Roof F— Roof Box

ZX210982 —UN—12JUL14

ZX210981 —UN—12JUL14

ZX210640 —UN—09APR14

A—Bottle Holder B—Cover C—A-Post Panel

Continued on next page

MHM1870 (04MAY20)

7

OUCC002,0006343 -19-30DEC19-4/18

060220

PN=9

BL16445, BL16446, and BL16447

7. Tractor with CommandARM™ a. Remove cover (A), right-hand console lower panel (B), then rear panel (C).

C—Rear Panel

ZX210978 —UN—20OCT14

ZX210980 —UN—20OCT14

A—Cover B—Right-Hand Console Lower Panel

ZX210979 —UN—20OCT14

IMPORTANT: To ease rear panel (C) removal, remove floor mat (not illustrated).

Continued on next page

MHM1870 (04MAY20)

8

OUCC002,0006343 -19-30DEC19-5/18

060220

PN=10

BL16445, BL16446, and BL16447

b.

NOTE: Preparation and removal of parts is nearly finished.

From step 9, the wiring harnesses installation starts.

B—Right-Hand Console Panel

ZX210985 —UN—20OCT14

A—Socket Panel

ZX210983 —UN—12JUL14

Disconnect and remove socket panel (A). Remove all fixing screws, then push right-hand console panel (B) away so that tractor cab wiring harnesses is accessible.

Continued on next page

MHM1870 (04MAY20)

9

OUCC002,0006343 -19-30DEC19-6/18

060220

PN=11

BL16445, BL16446, and BL16447

8. Tractor without CommandARM™

IMPORTANT: To ease rear panel (C) removal, remove floor mat (not illustrated). b. Remove all fixing screws, then push right-hand console panel (D) away so that tractor cab wiring harnesses is accessible. c. Remove covers (E) from the right-hand rear console panel (F), then remove panel (F).

ZX218073 —UN—20OCT14

a. Remove cover (A), right-hand console lower panel (B), then rear panel (C).

NOTE: Preparation and removal of parts is nearly finished.

From step 9, the wiring harnesses installation starts.

ZX210978 —UN—20OCT14

D—Right-Hand Console Panel E—Cover F— Right-Hand Rear Console Panel

ZX218075 —UN—06SEP14

ZX218074 —UN—06SEP14

A—Cover B—Right-Hand Console Lower Panel C—Rear Panel

Continued on next page

MHM1870 (04MAY20)

10

OUCC002,0006343 -19-30DEC19-7/18

060220

PN=12

ZX210987 —UN—12JUL14

ZX210986 —UN—12JUL14

BL16445, BL16446, and BL16447

9. Route part of cab roof wiring harness (A) with connector (B) through A—post passage (see arrow) down, then alongside the A—post as shown.

10. Connect CAN bus terminator (C) to the free mating connector (D).

11. Retain cab roof wiring harness (A) to cab wiring harness using tie bands (E).

D—Connector—CAN Bus Terminator E—Tie Band

ZX210988 —UN—12JUL14

A—Cab Roof Wiring Harness B—Connector—GreenStar™ Display C—CAN Bus Terminator

Continued on next page

MHM1870 (04MAY20)

11

OUCC002,0006343 -19-30DEC19-8/18

060220

PN=13

BL16445, BL16446, and BL16447

12. Insert connector (A) through A—post panel passage, then retain with nut (B) and plug (C) as shown.

ZX210989 —UN—12JUL14

IMPORTANT: To install A—post panel (D) back in place, install CAN bus terminator in such a way that it does not protrude from panel internal recess.

13. Install A—post panel (D) back in place.

A—Connector—GreenStar™ Display B—Nut

C—Plug D—A—Post Panel

Continued on next page

MHM1870 (04MAY20)

12

OUCC002,0006343 -19-30DEC19-9/18

060220

PN=14

ZX210990 —UN—12JUL14

ZX210991 —UN—12JUL14

BL16445, BL16446, and BL16447

14. On Tractor with Closed Cab Roof Only: a. To allow StarFire™ receiver connector installation, remove pre-cut area (A .

ZX210992 —UN—12JUL14

b. Route part of cab roof wiring harness (B) with connector (C) through grommet (D) up to the front wiper motor (E) as shown.

IMPORTANT: Route cab roof wiring harness (B) behind the motor (E) as shown. c. Insert connector (C) through the drilled hole, then retain with one strap (F), three self-taping screws M5X12 (G), and one spring nut (H) as shown.

ZX210993 —UN—12JUL14

E—Wiper Motor F— Strap G—Self-Taping Screw (M5X12) H—Spring Nut

ZX210994 —UN—12JUL14

A—Pre-Cut Area B—Cab Roof Wiring Harness C—Connector—StarFire™ Receiver D—Grommet

Continued on next page

MHM1870 (04MAY20)

13

OUCC002,0006343 -19-30DEC19-10/18

060220

PN=15

BL16445, BL16446, and BL16447

e. Route other part of cab roof wiring harness (C) alongside the tractor cab roof wiring harness up to the rear at the level of C—post passage, then retain cab roof wiring harness (C) with one tie band AH225366 (D) as shown.

IMPORTANT: Align green sticker on cab roof wiring harness (C) with tie band support as shown.

C—Cab Roof Wiring Harness D—Tie Band—AH225366

ZX210999 —UN—12JUL14

A—Connector—StarFire™ Receiver B—Plug

ZX210995 —UN—14JUL14

d. Plug connector StarFire™ receiver connector (A) with plug (B).

Continued on next page

MHM1870 (04MAY20)

14

OUCC002,0006343 -19-30DEC19-11/18

060220

PN=16

BL16445, BL16446, and BL16447

15. On Tractor with Panorama Cab Roof Only:

IMPORTANT: Passage (D) of cab roof harness (A) must be cut at the middle of the cab roof.

Route cab roof wiring harness (A) behind the guides (E) as shown. b. Route other part of cab roof wiring harness (A) alongside the tractor cab roof wiring harness up to the rear at the level of C—post passage, then retain cab roof wiring harness (A) with one tie band AH225366 (F) as shown.

ZX210996 —UN—12JUL14

a. Route part of cab roof wiring harness (A) with connector (B) through grommet (C) up to the passage (D) of cab roof as shown.

D—Passage E—Guides F— Tie Band—AH225366

ZX211000 —UN—12JUL14

ZX210998 —UN—12JUL14

A—Cab Roof Wiring Harness B—Connector—StarFire™ Receiver C—Grommet

ZX210997 —UN—12JUL14

IMPORTANT: Align green sticker on cab roof wiring harness (A) with tie band support as shown.

Continued on next page

MHM1870 (04MAY20)

15

OUCC002,0006343 -19-30DEC19-12/18

060220

PN=17

BL16445, BL16446, and BL16447

16. On Tractor without ITEC and without JDLink™:

b. Connect tractor wiring harness connector (A) to free mating connector (C) of cab roof wiring harness (D).

NOTE: Go to step 19 to continue wiring harness (D) installation.

C—Connector—Cab Roof Wiring Harness D—Cab Roof Wiring Harness

ZX218077 —UN—05SEP14

A—Connector—Tractor Wiring Harness B—Tractor Wiring Harness

ZX218076 —UN—05SEP14

a. At the level of cab roof fixing screw hole (see arrow), look for free connector (A) of tractor wiring harness (B).

OUCC002,0006343 -19-30DEC19-13/18

17. On Tractor with ITEC and without JDLink™: a. At the level of cab roof fixing screw hole (see arrow), disconnect connector (A) of ITEC wiring harness (B) from the tractor wiring harness connector (C).

ZX211001 —UN—12JUL14

b. Reconnect tractor wiring harness connector (C) to the free mating connector (D) of cab roof wiring harness (E).

NOTE: Go to step 18 to remove the ITEC wiring harness (B).

D—Connector—Cab Roof Wiring Harness E—Cab Roof Wiring Harness

ZX211002 —UN—12JUL14

A—Connector—ITEC B—ITEC Wiring Harness C—Connector—Tractor Wiring Harness

Continued on next page

MHM1870 (04MAY20)

16

OUCC002,0006343 -19-30DEC19-14/18

060220

PN=18

BL16445, BL16446, and BL16447

18. On Tractor with ITEC and JDLink™: a. At the level of cab roof fixing screw hole (see arrow), disconnect connector (A) of ITEC wiring harness (B) from connector (C) of JDLink™ wiring harness (D).

ZX211003 —UN—12JUL14

IMPORTANT: Do not disconnect the connector (E) of JDLink™ wiring harness (D). b. Connect JDLink™ wiring harness connector (C) to the free mating connector (F) of cab roof wiring harness (G).

NOTE: Continue with step 18 to remove the ITEC wiring harness (B).

E—Connector—JDLink™ Wiring Harness F— Connector—Cab Roof Wiring Harness G—Cab Roof Wiring Harness

ZX211004 —UN—12JUL14

A—Connector—ITEC B—ITEC Wiring Harness C—Connector—JDLink™ Wiring Harness D—JDLink™ Wiring Harness

Continued on next page

MHM1870 (04MAY20)

17

OUCC002,0006343 -19-30DEC19-15/18

060220

PN=19

BL16445, BL16446, and BL16447

19. Remove ITEC wiring harness (A) as follows: NOTE: ITEC wiring harness is made of two parts.

One part located inside cab roof and the other one alongside C—post.

ZX211005 —UN—12JUL14

a. At the level of the roof box, remove CAN bus terminator (B) from holder (C). b. Pull ITEC wiring harness (A) out of cab roof, then disconnect at connecting point (D).

C—Holder D—Connecting Point to Second Part

ZX211007 —UN—12JUL14

ZX211006 —UN—12JUL14

A—ITEC Wiring Harness—First Part B—CAN Bus Terminator

Continued on next page

MHM1870 (04MAY20)

18

OUCC002,0006343 -19-30DEC19-16/18

060220

PN=20

BL16445, BL16446, and BL16447

c. Remove second part of ITEC wiring harness (A) from C—post fixing points. d. At the level of the right-hand console, locate connecting point (B) between tractor cab wiring harness and second part of ITEC wiring harness (A). e. Disconnect and remove second part of ITEC wiring harness (A).

B—Connecting Point to Tractor Cab Wiring Harness

ZX211010 —UN—12JUL14

ZX211009 —UN—12JUL14

ZX211008 —UN—12JUL14

A—ITEC Wiring Harness—Second Part

Continued on next page

MHM1870 (04MAY20)

19

OUCC002,0006343 -19-30DEC19-17/18

060220

PN=21

BL16445, BL16446, and BL16447

C—Tractor Cab Roof Harness D—Tie Band

ZX211012 —UN—12JUL14

A—Connector B—Cab Roof Wiring Harness

ZX211011 —UN—12JUL14

20. Engage cab roof wiring harness connector (A) through C—post passage (see arrow), then retain cab roof wiring harness (B) with tractor cab roof harness (C) using tie bands (D) as shown.

OUCC002,0006343 -19-30DEC19-18/18

MHM1870 (04MAY20)

20

060220

PN=22

BL16445, BL16446, and BL16447

Install Attachment—ISO Wiring Harness, Power Socket, Display, and Signal Connectors ZX211020 —UN—12JUL14

1. Route part of ISO wiring harness (A) with connector (B) alongside C—post through passage (see arrow) and connect to relevant connector of cab roof wiring harness (C) as shown.

IMPORTANT: Once connected, make sure to place the connectors inside the C—post passage cavitation (not illustrated).

2. Retain ISO wiring harness (A) using tie bands (D).

C—Cab Roof Wiring Harness D—Tie Band

ZX211022 —UN—12JUL14

ZX211021 —UN—12JUL14

A—ISO Wiring Harness B—Connector—Cab Roof Wiring Harness Interface

Continued on next page

MHM1870 (04MAY20)

21

OUCC002,0006345 -19-30DEC19-1/9

060220

PN=23

BL16445, BL16446, and BL16447

3. Tractor with CommandARM™:

NOTE: Connector (C) is connecting point between tractor cab wiring harness and second part of ITEC wiring harness removed under step 18 of Install Attachment—Cab Roof Wiring Harness section. b. Install relay R339329 (D) to the free mating connector (E) of ISO wiring harness (A).

D—Relay—R339329 E—Connector

ZX211025 —UN—12JUL14

ZX211024 —UN—12JUL14

A—ISO Wiring Harness B—Right-Hand Console C—Connector—Connecting Point to ITEC Wiring Harness

ZX211023 —UN—12JUL14

a. Route other part of ISO wiring harness (A) underneath right-hand console panel (B), then connect to the free mating connector (C).

Continued on next page

MHM1870 (04MAY20)

22

OUCC002,0006345 -19-30DEC19-2/9

060220

PN=24

BL16445, BL16446, and BL16447

4. Tractor without CommandARM™:

b. Route other part of ISO wiring harness (B) underneath right-hand console panel (C), then connect connector (D) to the free mating connector (A). c. Install relay R339329 (E) to the free mating connector (F) of ISO wiring harness (A). d. Route part of ISO wiring harness (B) with relay R339329 (E) underneath the right-hand console frame, then retain with clamp (G) as shown.

ZX218084 —UN—05SEP14

E—Relay—R339329 F— Connector G—Clamp

ZX218086 —UN—05SEP14

ZX218085 —UN—05SEP14

A—Connector—Connecting Point to Cab Wiring Harness B—ISO Wiring Harness C—Right-Hand Console D—Connector

ZX218083 —UN—05SEP14

a. Look for free connector (A) from cab wiring harness.

Continued on next page

MHM1870 (04MAY20)

23

OUCC002,0006345 -19-30DEC19-3/9

060220

PN=25

ZX211027 —UN—12JUL14

ZX211026 —UN—12JUL14

BL16445, BL16446, and BL16447

5. If the tractor is not equipped with a socket outlet (A), then install socket AL66414 or 57M7390 as follows: a. Locate connector X239F-2 underneath right-hand console rear panel (B).

Terminal No.

Wire No.

Wire color

A

2012AB

Red

B

0427AC

Purple

C

0310AI

Black

ZX211028 —UN—12JUL14

Connector X239F-2 pin assignment

• On European Tractors: Use adapter harness AL114895 (C) and socket outlet AL66414 (A).

• On North American Tractors: Use adapter

harness AL178168 (C) and socket outlet 57M7390 (A).

ZX211029 —UN—12JUL14

NOTE: Installation of adapter harness (C) and socket outlet (A) on European tractor illustrated. b. Connect adapter harness AL114895 or AL178168 (C) to connectorX239F-2, then pass leads through strap L168794 (D) as shown. c. Pass adapter harness AL114895 or AL178168 (C) through passage of rear panel (B) as shown, then connect to the back of power socket outlet AL66414 or 57M7390 (A) using relevant X239F-2 pin assignment table.

ZX211030 —UN—12JUL14

NOTE: To allow socket outlet AL66414 or 57M7390 (A) installation, the strap L168794 (D) must stay underneath rear panel. d. Install power socket outlet AL66414 or 57M7390 (A) to rear panel (B) using four self-taping screws M3X13 (E) and four washers 3.2X7X0.5 (F).

A—Socket Outlet—AL66414 or 57M7390 B—Rear Panel C—Adapter Harness—AL114895 or AL178168 D—Strap—L168794

E—Self-Taping Screw (M3X13) F— Washer (3.2X7X0.5) X239F-2—Connector—Power Socket Interface

Continued on next page

MHM1870 (04MAY20)

24

OUCC002,0006345 -19-30DEC19-4/9

060220

PN=26

BL16445, BL16446, and BL16447

6. Tractor with CommandARM™: If the tractor is not equipped with a signal harness (A), then install signal harness as follows:

Connector X880F pin assignment Terminal No.

Wire No.

Wire color

A

4012AB

Red

B

6101A

Brown

C

5023A

Orange

D

4004A

Yellow

E

0372AC

Red

F

0050AU

Black

b. Install socket (C) of signal harness (A) to the socket panel L216547 (D) using one strap L214219 (E), two self-taping screws M3X13 (F), two washers 3.2X7X0.5 (G), and one protection cap 57M10651 (H) as shown. c. Connect signal harness (A) to connector X880F. F— Self-Taping Screw (M3X13) G—Washer (3.2X7X0.5) H—Protection Cap—57M10651 X880F—Connector—Signal Harness Interface

ZX211033 —UN—12JUL14

ZX211032 —UN—12JUL14

A—Signal Harness B—Rear Panel C—Socket—Signal D—Socket Panel—L216547 E—Strap—L214219

ZX211034 —UN—12JUL14

ZX211031 —UN—12JUL14

a. Locate connector X880F underneath right-hand console rear panel (B).

Continued on next page

MHM1870 (04MAY20)

25

OUCC002,0006345 -19-30DEC19-5/9

060220

PN=27

BL16445, BL16446, and BL16447

7. Tractor without CommandARM™: If the tractor is not equipped with a signal harness (A), then install signal harness as follows:

Connector X880F pin assignment Terminal No.

Wire No.

Wire color

A

4012AB

Red

B

6101A

Brown

C

5023A

Orange

D

4004A

Yellow

E

0372AC

Red

F

0050AU

Black

b. Install socket (C) of signal harness (A) to the inside of right-hand console panel (D) using two self-taping screws M3X13 (E), and two washers 3.2X7X0.5 (F) as shown.

E—Self-Taping Screw (M3X13) F— Washer (3.2X7X0.5) X880F—Connector—Signal Harness Interface

ZX218089 —UN—05SEP14

ZX218088 —UN—05SEP14

A—Signal Harness B—Rear Panel C—Socket—Signal D—Right-Hand Console Panel

ZX211034 —UN—12JUL14

ZX218087 —UN—05SEP14

a. Locate connector X880F underneath right-hand console rear panel (B).

Continued on next page

MHM1870 (04MAY20)

26

OUCC002,0006345 -19-30DEC19-6/9

060220

PN=28

BL16445, BL16446, and BL16447

8. Tractor with CommandARM™:

ZX211035 —UN—12JUL14

a. Install the CAN bus socket (A) of ISO wiring harness (B) on socket panel L216547 (C) using one strap L214219 (D), four self-taping screws M3X13 (E), and four washers 3.2X7X0.5 (F) as shown. b. Install the GreenStar™ display socket (G) of ISO wiring harness (B) on socket panel L216547 (C), as shown.

E—Self-Taping Screw (M3X13) F— Washer (3.2X7X0.5) G—Socket—GreenStar™ Display

ZX211038 —UN—12JUL14

ZX211037 —UN—12JUL14

ZX211036 —UN—12JUL14

A—Socket—CAN Bus B—ISO Wiring Harness C—Socket Panel—L216547 D—Strap—L214219

Continued on next page

MHM1870 (04MAY20)

27

OUCC002,0006345 -19-30DEC19-7/9

060220

PN=29

BL16445, BL16446, and BL16447

9. Tractor without CommandARM™:

b. Install CAN bus socket (D) of ISO wiring harness (B) on socket panel L216548 (C) using one strap L214219 (E), four self-taping screws M3X13 (F), four washers 3.2X7X0.5 (G), and one protection 57M10653 cap (H) as shown.

E—Strap—L214219 F— Self-Taping Screw (M3X13) G—Washer (3.2X7X0.5) H—Protection Cap—57M10653

ZX218093 —UN—05SEP14

ZX218092 —UN—05SEP14

ZX218091 —UN—05SEP14

A—Socket—GreenStar™ Display B—ISO Wiring Harness C—Socket Panel— L216548 D—Socket—CAN Bus

ZX218090 —UN—05SEP14

a. Install GreenStar™ display socket (A) of ISO wiring harness (B) on socket panel L216548 (C) as shown.

Continued on next page

MHM1870 (04MAY20)

28

OUCC002,0006345 -19-30DEC19-8/9

060220

PN=30

BL16445, BL16446, and BL16447

10. Install one plug (A) on socket panel L216547 or L216548 (B), then reconnect Ethernet cables (C) to their relevant receptacle (D), if necessary.

11. Install socket panel assembly on rear panel then install all previously removed panels back in place.

D—Receptacle E—Plug

ZX218094 —UN—05SEP14

ZX211040 —UN—12JUL14

A—Plug B—Socket Panel—L216547 or L216548 C—Ethernet Cable

ZX211039 —UN—12JUL14

NOTE: If no Ethernet cable is installed, then install plug (E) instead.

OUCC002,0006345 -19-30DEC19-9/9

MHM1870 (04MAY20)

29

060220

PN=31

BL16445, BL16446, and BL16447

Install Attachment—Relay and Fuses On cab relay box (A), install:

• Relay AL76702—10/20A (B) at LCS-01—20 emplacement (C) as shown.

ZX210974 —UN—12JUL14

• Fuse 10A (D) at LCS-01—18 emplacement (E) as shown.

• Fuse 10A (D) at LCS-01—17 emplacement (F) as shown.

D—Fuse 10A E—LCS-01—18 Emplacement F— LCS-01—17 Emplacement

ZX210976 —UN—12JUL14

ZX210975 —UN—12JUL14

A—Relay Box B—Relay—AL76702 (10/20A) C—LCS-01—20 Emplacement

Continued on next page

MHM1870 (04MAY20)

30

OUCC002,0006346 -19-30DEC19-1/3

060220

PN=32

BL16445, BL16446, and BL16447

On 6110R—6155R Tractors Only: On relay box (A), install:

• Relay AL77324—40A (B) at K02/09 emplacement (C) as shown.

D—Relay Power Socket Bat—AL207376 (70A) E—K02/03 emplacement

ZX210971 —UN—12JUL14

A—Relay Box B—Relay Power Socket ECU Bat—AL77324 (40A) C—K02/09 Emplacement

ZX210970 —UN—20OCT14

as shown.

• Relay AL207376—70A (D) at K02/03 emplacement (E)

OUCC002,0006346 -19-30DEC19-2/3

On 6175R—6215R Tractors Only: On relay box (A), install:

• Relay AL77324—40A (B) at K02/02 emplacement (C) as shown.

D—Relay Power Socket Bat—AL207376 (70A) E—K02/01 Emplacement

ZX210973 —UN—12JUL14

A—Relay Box B—Relay Power Socket ECU Bat—AL77324 (40A) C—K02/02 Emplacement

ZX210972 —UN—12JUL14

as shown.

• Relay AL207376—70A (D) at K02/01 emplacement (E)

OUCC002,0006346 -19-30DEC19-3/3

MHM1870 (04MAY20)

31

060220

PN=33

BL16445, BL16446, and BL16447

Install Attachment—GreenStar™ Display Bracket The GreenStar™ display bracket can be installed either on A—post or on C—post, as follows: 1. Install On A—Post:

• Install the GreenStar™ display bracket (A) on the

A—post using two oval socket head screws M10X20 (B).

NOTE: If equipped with, install cup holder support back in place.

B—Oval Socket Head Screw (M10X20)

ZX211015 —UN—12JUL14

A—GreenStar™ Display Bracket

Continued on next page

MHM1870 (04MAY20)

32

OUCC002,0006348 -19-30DEC19-1/3

060220

PN=34

BL16445, BL16446, and BL16447

2. Install On C—Post: drill two 20 mm (0.8 in) diameter holes as shown (see arrows).

• Install the GreenStar™ display bracket (B) on the C—post using two oval socket head screws M10X20 (C).

C—Oval Socket Head Screw (M10X20)

ZX214854 —UN—05SEP14

A—C—Post Panel B—GreenStar™ Display Bracket

ZX214855 —UN—05SEP14

• Before installing C—post panel (A) back in place,

Continued on next page

MHM1870 (04MAY20)

33

OUCC002,0006348 -19-30DEC19-2/3

060220

PN=35

BL16445, BL16446, and BL16447

3. Connect GreenStar™ Display: Connect GreenStar™ display adapter harness (A) between display (B) and A—post connector (C) or C—post connector (D).

C—A—Post Connector D—C—Post Connector

ZX214856 —UN—05SEP14

ZX211016 —UN—05SEP14

A—Display Adapter Harness B—GreenStar™ Display

OUCC002,0006348 -19-30DEC19-3/3

MHM1870 (04MAY20)

34

060220

PN=36

BL16445, BL16446, and BL16447

Install Attachment—GPS Receiver Bracket Depending on the tractor cab roof type, install the GPS receiver bracket as follows:

1. Place receiver bracket (A) on front of outer face of cab roof (B), as shown.

2. Align fixing holes of bracket (A) with pre-stamped holes on cab roof (B)—see arrows.

3. Drill four 4.5 mm (0.177 in.) diameter holes at the desired locations.

ZX211013 —UN—12JUL14

Tractor with Standard Cab Roof

4. Attach receiver bracket (A) on cab roof (B) using four self-taping screws M6X20 (C).

5. Install cab roof (B) back in place.

C—Self-Taping Screw (M6X20)

ZX211014 —UN—12JUL14

A—Receiver Bracket B—Cab Roof

Continued on next page

MHM1870 (04MAY20)

35

OUCC002,0006349 -19-30DEC19-1/2

060220

PN=37

BL16445, BL16446, and BL16447 Tractor with Panoramic Cab Roof

2. Align fixing holes of the bracket (A) with holes on cab roof (B) and attach with four self-taping screw M6X20 (C).

3. Install cab roof (B) back in place.

4. Install connector (D) to receiver bracket (A) using one screw M4X12 (E).

5. Install cover (F) on the GPS receiver bracket (A) using one screw M4X12 (E).

ZX211017 —UN—12JUL14

1. Place GPS receiver bracket (A) on front of inner face of cab roof (B) as shown.

6. Plug connector (D) with plug (G).

ZX211018 —UN—20OCT14

7. Place clamp AL206078 (H) at any location on GPS receiver bracket (A) as shown.

NOTE: To retain the GPS receiver connector cable, use the clamp AL206078 (H).

E—Screw (M4X12) F— Cover G—Plug H—Clamp—AL206078

ZX211019 —UN—20OCT14

A—Install GPS Receiver Bracket B—Cab Roof C—Self-Taping Screw (M6X20) D—Connector—StarFire™ Receiver

OUCC002,0006349 -19-30DEC19-2/2

MHM1870 (04MAY20)

36

060220

PN=38

BL16445, BL16446, and BL16447

Install Attachment—Power Harness CAUTION: Before taking off the rear wheel, take note of the following safety instructions.

ZX211041 —UN—12JUL14

Remove a wheel on level ground only. The other wheels must be secured by means of chock blocks to prevent a tractor runaway.

The tractor must be supported safely (to avoid accidents).

Due to the big size and the heavy weight of tractor wheels, pay attention to the following points when removing wheels:

• Before removing wheels, place tractor on firm, level ground.

• Engage park lock and prevent the tractor from rolling away by putting down chock blocks.

• Remove the ignition key to prevent unauthorized operation.

• When removing rear wheels, prevent front axle oscillation by using wedges.

• When jacking up the tractor, only use the recommended lifting points, see tractor Operator's Manual.

• Use a stable jack with sufficient lifting force. See tractor Operator's Manual.

• Stop jacking up the tractor when the wheel is completely off the ground.

• Use special tool KJD10581 trolley when removing the rear wheel.

• Support the tractor when a wheel is removed. Jack

ZX211042 —UN—12JUL14

stands are available as special tools JT02043 and JT02044.

• When installing wheels, make sure that the correct torques are applied, see Tighten Wheel Bolts and Wheel Weights section of the tractor Operator's Manual.

CAUTION: Do not operate the tractor until the wheel installation has been completed.

When removing a wheel, make sure that no-one is standing in the danger zone.

When removing a wheel, make sure that the tractor is supported safely.

A—Axle

When storing removed wheels, make sure that they cannot fall.

1. Remove the rear right-hand wheel and safely support the axle (A).

To install the power harness the rear right-hand wheel and some covers must be removed. Proceed as follows: Continued on next page

MHM1870 (04MAY20)

37

OUCC002,000633E -19-05JAN20-1/25

060220

PN=39

BL16445, BL16446, and BL16447

2. Remove the foot step (A) and the cover (C).

NOTE: If equipped with, disconnect and remove step light (C).

C—Step Light

LX398426 —UN—02JAN20

A—Foot Step Assembly B—Cover

Continued on next page

MHM1870 (04MAY20)

38

OUCC002,000633E -19-05JAN20-2/25

060220

PN=40

ZX211047 —UN—12JUL14

ZX211046 —UN—12JUL14

BL16445, BL16446, and BL16447

3. On Tractor without Hydraulic Cab Suspension Only:

a. Remove screws (A) and attach the KJD10592 lifting crossbar and hoist b. Lift the floor mat on and remove screws (B) on both sides of the cab. c. Remove cab rear mounting screws (C) on both sides.

ZX211048 —UN—12JUL14

To help installing the power harness it is necessary to raise the cab. Proceed as follows:

d. Carefully raise the cab about 50 mm (2 in). e. Safely support cab using adequate blocks (D) as shown.

ZX211049 —UN—12JUL14

C—Screw—Rear Cab Support D—Block

ZX211050 —UN—12JUL14

A—Screw—Cab Roof B—Screw—Cab Floor

Continued on next page

MHM1870 (04MAY20)

39

OUCC002,000633E -19-05JAN20-3/25

060220

PN=41

BL16445, BL16446, and BL16447

4. On Tractor with Hydraulic Cab Suspension Only: To help installing the power harness it is necessary to raise the cab. Proceed as follows:

NOTE: Access the diagnostic address CSC-23 to raise the cab. b. Extend hydraulic cylinders (A) until the cab bumpers (B) bottom with their guides.

B—Bumper

ZX213096 —UN—12JUL14

A—Hydraulic Cylinder

ZX213095 —UN—12JUL14

a. Raise cab. Refer to the tractor Operator’s Manual.

Continued on next page

MHM1870 (04MAY20)

40

OUCC002,000633E -19-05JAN20-4/25

060220

PN=42

BL16445, BL16446, and BL16447

5. On 6110R—6135R Tractor Only (if necessary):

a. Loosen both nuts (C), then remove socket-head screws (D). b. Rotate support (A) 90 degrees counterclockwise, then attach with socket-head screws (D) as shown. c. Tighten nuts (C).

C—Nut D—Socket-Head Screw

ZX214859 —UN—05SEP14

ZX214858 —UN—05SEP14

A—Support B—Connector

ZX214857 —UN—05SEP14

If air brake connector support (A) is oriented vertically, then relocate support (A) and connector (B) as follows:

Continued on next page

MHM1870 (04MAY20)

41

OUCC002,000633E -19-05JAN20-5/25

060220

PN=43

ZX213098 —UN—12JUL14

ZX213097 —UN—12JUL14

BL16445, BL16446, and BL16447

6. On 6110R—6155R Tractor Only: a. Remove relay box fixing screws (A), then separate relay box (B) from foot step support (C).

c. Remove step support fixing screws (E) then support (C). d. Remove wiring harness channel covers (F) and (G) located underneath the cab.

E—Screw F— Cover G—Cover

ZX213101 —UN—12JUL14

ZX213100 —UN—12JUL14

A—Screw B—Relay Box C—Support D—Clamp

ZX213099 —UN—12JUL14

b. Remove clamp (D) from foot step support (C).

Continued on next page

MHM1870 (04MAY20)

42

OUCC002,000633E -19-05JAN20-6/25

060220

PN=44

BL16445, BL16446, and BL16447

7. On 6175R— 6215R Tractor Only: a. Remove handrail assembly (A), then remove the SRC system outer cover (B). b. Remove SRC system sensor cover (C).

C—Sensor Cover

LX398429 —UN—02JAN20

LX398428 —UN—02JAN20

A—Handrail B—Outer Cover

Continued on next page

MHM1870 (04MAY20)

43

OUCC002,000633E -19-05JAN20-7/25

060220

PN=45

BL16445, BL16446, and BL16447

c. Remove all fixing screws of SRC system inner cover (A) but do not remove cover (A). d. Remove engine side shield (B).

B—Engine Side Shield

ZX213105 —UN—12JUL14

ZX213104 —UN—12JUL14

A—Inner Cover

Continued on next page

MHM1870 (04MAY20)

44

OUCC002,000633E -19-05JAN20-8/25

060220

PN=46

BL16445, BL16446, and BL16447

e. Remove the side cover (A) of the exhaust system. f. Remove top cover (B), then front covers (C) and (D).

C—Front Cover D—Front Cover

ZX213108 —UN—27MAR20

ZX213107 —UN—12JUL14

ZX213106 —UN—12JUL14

A—Side Cover B—Top Cover

Continued on next page

MHM1870 (04MAY20)

45

OUCC002,000633E -19-05JAN20-9/25

060220

PN=47

BL16445, BL16446, and BL16447

g. Remove SRC system lower cover (A). h. Remove relay box fixing screws (B), then separate relay box (C) from foot step support (D).

ZX213109 —UN—12JUL14

C—Relay Box D—Support

ZX213112 —UN—12JUL14

ZX213111 —UN—12JUL14

ZX213110 —UN—12JUL14

A—Lower Cover B—Screw

Continued on next page

MHM1870 (04MAY20)

46

OUCC002,000633E -19-05JAN20-10/25

060220

PN=48

ZX213114 —UN—12JUL14

ZX213113 —UN—12JUL14

BL16445, BL16446, and BL16447

i. To disengage the relay box (A), pull it up from its support (B).

k. Remove step support fixing screws (D), then support (C). l. Remove clamp (E) from foot step support (C). m. Remove wiring harness channel covers (F) and (G) located underneath the cab. To remove cover (G), remove first screw (H) located between the cab and the exhaust system pipe.

E—Clamp F— Cover G—Cover H—Screw

ZX213117 —UN—12JUL14

ZX213116 —UN—12JUL14

A—Relay Box B—Support—Relay Box C—Support—Foot Step D—Screw

ZX213115 —UN—12JUL14

j. Remove relay box support (B) from foot step support (C).

Continued on next page

MHM1870 (04MAY20)

47

OUCC002,000633E -19-05JAN20-11/25

060220

PN=49

ZX213123 —UN—12JUL14

ZX213122 —UN—12JUL14

BL16445, BL16446, and BL16447

8. On All Tractors:

b. Attach power harness (A) to the hydraulic line using clamp L210203 (C) as shown.

NOTE: If necessary, order clamp L210203 (C) separately. c. Continue routing power harness (A) between the hitch frame up to the back of the implement socket holder (D), as shown.

C—Clamp—L210203 D—Holder

ZX213125 —UN—05SEP14

ZX213124 —UN—12JUL14

A—Power Harness B—Connector

ZX218078 —UN—16DEC14

a. Route part of power harness (A) with connectors (B) behind the hydraulic lines to the rear of the tractor, as shown.

Continued on next page

MHM1870 (04MAY20)

48

OUCC002,000633E -19-05JAN20-12/25

060220

PN=50

BL16445, BL16446, and BL16447

IMPORTANT: Place adapter (D) so that face with protrusions is oriented toward back of the implement socket (C) as shown (see arrow). e. Install implement socket (C) to its holder using four pan head screws M6X55 (E) and four self-locking nuts M6 (F) as shown. f. Retain part of power harness (G) to tractor wiring harness using two tie bands (H) as shown.

E—Pan Head Screw (M6X55) (4 used) F— Self-Locking Nut (M6) G—Power Harness H—Tie Band

ZX213129 —UN—12JUL14

ZX213128 —UN—12JUL14

ZX213127 —UN—12JUL14

A—Connector B—Connector C—Implement Socket D—Adapter

ZX213126 —UN—12JUL14

d. Connect connectors (A) and (B) to their relevant receptacle of the implement socket (C) through adapter (D) as shown.

Continued on next page

MHM1870 (04MAY20)

49

OUCC002,000633E -19-05JAN20-13/25

060220

PN=51

BL16445, BL16446, and BL16447

9. On 6110R—6135R Tractor Only:

NOTE: If connector (D) is connected to the adapter cable (E), then disconnect adapter cable (E) and CAN bus terminator (F) from connector (D). b. Route power harness (A) alongside tractor wiring harness, then connect connector (B) to connector (D).

ZX218079 —UN—05SEP14

a. Place part of power harness (A) with connector (B) at the level of transmission connecting box (C), as shown. Look for the tractor wiring harness free connector (D).

c. Retain power harness (A) with a tie band (G) as shown.

ZX218080 —UN—05SEP14

E—Adapter Cable F— CAN Bus Terminator G—Tie Band

ZX218082 —UN—05SEP14

ZX218081 —UN—05SEP14

A—Power Harness B—Connector C—Connection Box D—Connector—Tractor Interface

Continued on next page

MHM1870 (04MAY20)

50

OUCC002,000633E -19-05JAN20-14/25

060220

PN=52

BL16445, BL16446, and BL16447

10. On 6145R—6215R Tractor Only:

b. Route power harness (A) alongside the hydraulic oil reservoir (see arrow), then connect connector (B) to connector (C). c. Retain connector with a tie band (D) as shown.

C—Connector—Tractor Interface D—Tie Band

ZX213121 —UN—12JUL14

ZX213120 —UN—12JUL14

ZX213119 —UN—12JUL14

A—Power Harness B—Connector

ZX213118 —UN—12JUL14

a. Place part of power harness (A) with connector (B) at the level of the hydraulic oil reservoir as shown.

Uncap tractor wiring harness free connector (C) located behind the hydraulic oil reservoir.

Continued on next page

MHM1870 (04MAY20)

51

OUCC002,000633E -19-05JAN20-15/25

060220

PN=53

ZX213131 —UN—12JUL14

ZX213130 —UN—12JUL14

BL16445, BL16446, and BL16447

11. On 6110R—6155R Tractor Only: a. Route power harness (A) through the rear cable channel (B) as shown.

ZX213132 —UN—12JUL14

b. Remove side cable channel (C).

IMPORTANT: Note position of each cable while removing cable channel (C) for further installation. c. Route part (D) of power harness (A) with the ground terminal through second passage (E) on the left-hand side of channel (F) above the tractor frame as shown.

D—Ground Terminal Cable E—Passage F— Channel

ZX213133 —UN—12JUL14

A—Power Harness B—Rear Channel C—Side Channel

Continued on next page

MHM1870 (04MAY20)

52

OUCC002,000633E -19-05JAN20-16/25

060220

PN=54

BL16445, BL16446, and BL16447

d. Remove transmission shield (A) to access frame ground connecting stud (B) on the tractor frame, then connect ground terminal of power harness using one flange nut (M8).

ZX213134 —UN—12JUL14

NOTE: Stud (B) is located underneath the cab on the inner side of the tractor right-hand frame.

Install shield (A) back in place.

B—Stud—Frame Ground

ZX213135 —UN—12JUL14

A—Shield

Continued on next page

MHM1870 (04MAY20)

53

OUCC002,000633E -19-05JAN20-17/25

060220

PN=55

BL16445, BL16446, and BL16447

e. Route part of power harness (A) with connectors (B) through the second lower passage (C) on the right-hand side channel (D) as shown. f. Connect Yellow connector (E) on its relevant receptacle of the power box (F).

D—Side Channel E—Connector—Yellow F— Receptacle

ZX213138 —UN—12JUL14

ZX213137 —UN—12JUL14

ZX213136 —UN—12JUL14

A—Power Harness B—Connector C—Passage

Continued on next page

MHM1870 (04MAY20)

54

OUCC002,000633E -19-05JAN20-18/25

060220

PN=56

BL16445, BL16446, and BL16447

g. Connect Gray connector (A) on its relevant receptacle of the power box (B).

ZX213139 —UN—14JUL14

h. Install wiring harness channel cover (C) back in place, then retain power harness (D) with tie bands (E) as shown. i. Install wiring harness channel cover (F) back in place. j. Install all parts removed during tractor preparation back in place.

D—Power Harness E—Tie Band F— Cover

ZX213142 —UN—12JUL14

ZX213141 —UN—12JUL14

ZX213140 —UN—14JUL14

A—Connector—Gray B—Receptacle C—Cover

Continued on next page

MHM1870 (04MAY20)

55

OUCC002,000633E -19-05JAN20-19/25

060220

PN=57

BL16445, BL16446, and BL16447

12. On 6175R— 6215R Tractor Only: a. To allow power harness passage, remove rear cable channel (A), then detach part (B).

D—Cover E—Screw

ZX213145 —UN—14JUL14

ZX213144 —UN—14JUL14

A—Channel B—Part to Detach C—Power Harness

ZX213143 —UN—14JUL14

b. Route power harness (C) through the rear cable channel (A), then install cover (D) back in place.

Retain cover (D) with original screws (E).

Continued on next page

MHM1870 (04MAY20)

56

OUCC002,000633E -19-05JAN20-20/25

060220

PN=58

BL16445, BL16446, and BL16447

c. Note their respective position, then disconnect all connectors (A) from the bottom part (B) of the side cable channel.

IMPORTANT: Note position of each cable while removing cable channel bottom part (B) for further installation. e. Route part of power harness (D) with connectors (E) toward the relay box, then remove the side cable bottom part (B) as shown.

ZX213146 —UN—14JUL14

d. Remove the top part (C) of the side cable channel.

NOTE: Bottom part (B) of the side cable channel is held in place with four screws.

D—Power Harness E—Connector

ZX213148 —UN—14JUL14

ZX213147 —UN—14JUL14

A—Connector B—Side Channel—Bottom Part C—Side Channel—Top Part

Continued on next page

MHM1870 (04MAY20)

57

OUCC002,000633E -19-05JAN20-21/25

060220

PN=59

BL16445, BL16446, and BL16447

g. Connect ground terminal of power harness (B) on frame ground connecting stud (D) using one flange nut (M8).

NOTE: Stud (D) is located underneath the cab on the inner side of the tractor right-hand frame.

C—Channel D—Stud

ZX213151 —UN—14JUL14

ZX213150 —UN—14JUL14

A—Ground Terminal Cable B—Power Harness

ZX213149 —UN—14JUL14

f. Route part (A) of power harness (B) with the ground terminal through second passage (see arrow) on the left-hand side of channel (C) above the tractor frame as shown.

Continued on next page

MHM1870 (04MAY20)

58

OUCC002,000633E -19-05JAN20-22/25

060220

PN=60

BL16445, BL16446, and BL16447

h. Detach part (A) of the side channel bottom part (B). i. Install bottom part (B) of the side channel back in place with power harness (C) inserted through relevant passage, then install top part (D), as shown.

D—Side Channel—Top Part E—Connector F— Cover

ZX213155 —UN—14JUL14

ZX213154 —UN—14JUL14

ZX213153 —UN—14JUL14

A—Part to Detach B—Side Channel—Bottom Part C—Power Harness

ZX213152 —UN—14JUL14

j. Reconnect all connectors (E), then install wiring harness channel cover (F) back in place.

Continued on next page

MHM1870 (04MAY20)

59

OUCC002,000633E -19-05JAN20-23/25

060220

PN=61

BL16445, BL16446, and BL16447

k. From the back of the power box, remove and discard protection cap (A), then connect Yellow connector (B) on its relevant receptacle of the power box (C).

ZX213156 —UN—14JUL14

C—Receptacle

ZX213158 —UN—14JUL14

ZX213157 —UN—14JUL14

A—Protection Cap B—Connector—Yellow

Continued on next page

MHM1870 (04MAY20)

60

OUCC002,000633E -19-05JAN20-24/25

060220

PN=62

BL16445, BL16446, and BL16447

l. From the back of the power box, disconnect Yellow connector (A), then remove and discard protection cap (B).

n. Connect Yellow connector (A) back on its relevant port of the power box. o. Install all parts removed during tractor preparation back in place.

C—Connector—Gray

ZX213162 —UN—14JUL14

ZX213161 —UN—14JUL14

ZX213160 —UN—14JUL14

A—Connector—Yellow B—Protection Cap

ZX213159 —UN—14JUL14

m. Connect Gray connector (C) on its relevant receptacle of the power box.

OUCC002,000633E -19-05JAN20-25/25

MHM1870 (04MAY20)

61

060220

PN=63

BL16445, BL16446, and BL16447

Check Implement Power Socket Connections IMPORTANT: Wrong connection of the power supply can damage your system.

LX398411 —UN—30DEC19

Test the system at socket (A) using a multimeter as follows: 1. Switch power OFF (ignition key). a. Measure voltage between pin 3 (12 volt power supply) and pin 1 (ground). Voltage level must be 0 volt. b. Measure voltage between pin 4 (12 volt power supply) and pin 2 (ground). Voltage level must be 0 volt after a delay of MAX 5 seconds.

2

c. Measure voltage between pin 6 (12 volt power supply) and pin 7 (ground). Voltage level must be 0 volt.

1

a. Measure voltage between pin 3 (12 volt power supply) and pin 1 (ground). Voltage level must be about 12 volts.

c. Measure voltage between pin 6 (12 volt power supply) and pin 7 (ground). Voltage level must be about 12 volts.

6

7 ZX1041088

ZX1041088 —UN—27SEP07

4

2. Switch Power ON (ignition key).

b. Measure voltage between pin 4 (12 volt power supply) and pin 2 (ground). Voltage level must be about 12 volts.

3

A—Socket

6 — Pin 6 (12 volt power supply) 7 — Pin 7 (ground)

1 — Pin 1 (ground) 2 — Pin 2 (ground) 3 — Pin 3 (12 volt power supply) 4 — Pin 4 (12 volt power supply)

OUCC002,0006347 -19-30DEC19-1/1

Reinstall Necessary Parts and Check Function Reinstall necessary parts.

IMPORTANT: Once all the component assemblies have been installed, do an operational check.

Connect battery.

Check new function.

AK53658,0000D16 -19-18OCT19-1/1

MHM1870 (04MAY20)

62

060220

PN=64

BL16445, BL16446, and BL16447

ZX210966 —UN—05SEP14

Parts List for BL16445 Attachment

Item

Part no.

Designation

Quantity

A B

AL227678

Power Harness

1

14M7397

Self-Locking Nut (M6)

4

C

19M9343

Pan Head Screw (M6X55)

4

D

AL77324

Relay 40A

1

Continued on next page

MHM1870 (04MAY20)

63

OUCC002,0006340 -19-30DEC19-1/2 060220

PN=65

BL16445, BL16446, and BL16447 Item

Part no.

Designation

Quantity

E

AL207376

Relay 70A

1

F

RE568839

Electrical Connector 60A/CAN Implement

1

G

L41858

Tie Band—360 mm (1 ft 2.17 in)

5

H

14M7298

Flange Nut (M8)

1

I

L214190

Adapter

1

Z200300

Downloading Instructions

1

MHM1870

Installation Instructions

1 OUCC002,0006340 -19-30DEC19-2/2

MHM1870 (04MAY20)

64

060220

PN=66

BL16445, BL16446, and BL16447

LX405136 —UN—06APR20

Parts List for BL16446 Attachment

Parts List for BL16446 Attachment—Part 1 Item

Part no.

Designation

Quantity

A

AL114895a

Wiring Harness, 3-Pin Socket (European Tractors)

1

B

AL114896

a

Wiring Harness, 3-Pin Socket (North American Tractors)

1

C

AL207440a

Wiring Harness, Signal Connector

1

Continued on next page

MHM1870 (04MAY20)

65

OUCC002,000633F -19-06APR20-1/5 060220

PN=67

BL16445, BL16446, and BL16447 Item

Part no.

Designation

Quantity

D

AL175883

a

Wiring Harness, A-Post Display

1

E

AL228789a

Bracket, GreenStar™ Display

1

F

AL226953

a

Wiring Harness, Cab Roof

1

G

AL221946a

Wiring Harness, ISO Connect

1

Z200300

Downloading Instructions

1

MHM1870

Installation Instructions

1

a

Part of package BL16448 Continued on next page

MHM1870 (04MAY20)

66

OUCC002,000633F -19-06APR20-2/5

060220

PN=68

LX398409 —UN—30DEC19

BL16445, BL16446, and BL16447

Parts List for BL16446 Attachment—Part 2 Item

Part no.

Designation

Quantity

A

24M7029a

Washer (3.2x7x0.5)

10

a

B

37M7095

Self-taping screw (M3x13)

10

C

57M10651a

Protection cap—Signal connector

1

D

a

Protection cap—ISO connector

1

57M10653

Continued on next page

MHM1870 (04MAY20)

67

OUCC002,000633F -19-06APR20-3/5 060220

PN=69

BL16445, BL16446, and BL16447 Item

Part no.

Designation a

Quantity

E

57M11226

Connector plug

1

F

57M7689a

Fuse 10A

2

G

57M7390a

Socket outlet (North American tractors)

1

H

AL201803a

Protection cap (North American tractors)

1

a

I

AL66414

Socket outlet (European tractors)

1

J

AL76702a

Relay 10/20A

1

K

L168794

a

Strap

1

L

L214219a

Strap

1

M

L166804

a

N

HXE21678a

O

L204137

a

P

RE207311a

Q

a

R S

L216548

a

T

L100285a

U

R339329

a

V

L41858a

Dummy plug

1

Ethernet dummy plug

2

Plug

1

CAN Bus terminator

1

AH225366

Tie band

2

L216547a

Panel

1

Panel

1

Oval head cap screw (M10x20)

2

Relay with connector

1

Tie Band—360 mm (1 ft 2.17 in)

5

a

Part of package BL16448 Continued on next page

MHM1870 (04MAY20)

68

OUCC002,000633F -19-06APR20-4/5

060220

PN=70

ZX210964 —UN—12JUL14

BL16445, BL16446, and BL16447

Parts List for BL16446 Attachment—Part 3 Item

Part no.

Designation

Quantity

A

PF81190

Receiver Support

1

B

R224342

Self-Taping Screw (M6x20)

4

C

L201686

Strap

1

D

37M7357

Self-Taping Screw (M5x12)

3

E

L156275

Spring Nut

1 OUCC002,000633F -19-06APR20-5/5

MHM1870 (04MAY20)

69

060220

PN=71

BL16445, BL16446, and BL16447

LX405136 —UN—06APR20

Parts List for BL16447 Attachment

Parts List for BL16447 Attachment—Part 1 Item

Part no.

Designation

Quantity

A

AL114895a

Wiring Harness, 3-Pin Socket (European Tractors)

1

B

AL114896

a

Wiring Harness, 3-Pin Socket (North American Tractors)

1

C

AL207440a

Wiring Harness, Signal Connector

1

Continued on next page

MHM1870 (04MAY20)

70

OUCC002,0006342 -19-06APR20-1/5 060220

PN=72

BL16445, BL16446, and BL16447 Item

Part no.

Designation

Quantity

D

AL175883

a

Wiring Harness, A-Post Display

1

E

AL228789a

Bracket, GreenStar™ Display

1

F

AL226953

a

Wiring Harness, Cab Roof

1

G

AL221946a

Wiring Harness, ISO Connect

1

Z200300

Downloading Instructions

1

MHM1870

Installation Instructions

1

a

Part of package BL16448 Continued on next page

MHM1870 (04MAY20)

71

OUCC002,0006342 -19-06APR20-2/5

060220

PN=73

LX398409 —UN—30DEC19

BL16445, BL16446, and BL16447

Parts List for BL16447 Attachment—Part 2 Item

Part no.

Designation

Quantity

A

24M7029a

Washer (3.2x7x0.5)

10

a

B

37M7095

Self-taping screw (M3x13)

10

C

57M10651a

Protection cap—Signal connector

1

D

a

Protection cap—ISO connector

1

57M10653

Continued on next page

MHM1870 (04MAY20)

72

OUCC002,0006342 -19-06APR20-3/5 060220

PN=74

BL16445, BL16446, and BL16447 Item

Part no.

Designation a

Quantity

E

57M11226

Connector plug

1

F

57M7689a

Fuse 10A

2

G

57M7390a

Socket outlet (North American tractors)

1

H

AL201803a

Protection cap (North American tractors)

1

a

I

AL66414

Socket outlet (European tractors)

1

J

AL76702a

Relay 10/20A

1

K

L168794

a

Strap

1

L

L214219a

Strap

1

M

L166804

a

N

HXE21678a

O

L204137

a

P

RE207311a

Q

a

R S

L216548

a

T

L100285a

U

R339329

a

V

L41858a

Dummy plug

1

Ethernet dummy plug

2

Plug

1

CAN Bus terminator

1

AH225366

Tie band

2

L216547a

Panel

1

Panel

1

Oval head cap screw (M10x20)

2

Relay with connector

1

Tie Band—360 mm (1 ft 2.17 in)

5

a

Part of package BL16448 Continued on next page

MHM1870 (04MAY20)

73

OUCC002,0006342 -19-06APR20-4/5

060220

PN=75

ZX210968 —UN—12JUL14

BL16445, BL16446, and BL16447

Parts List for BL16447 Attachment—Part 3 Item

Part no.

Designation

A

AL204387

Support

1

B

L205618

Cover

1

C

AL206078

Clip

1

D

R224342

Self-Taping Screw (M6x20)

4

E

21M7250

Screw (M4x12)

2

Quantity

OUCC002,0006342 -19-06APR20-5/5

MHM1870 (04MAY20)

74

060220

PN=76