Grove GMK 3060i Lattice Extension Operating Manual 3113112 - PDF DOWNLOAD

Operating manual Lattice extension

3 113 112 en 27.05.2014

Important note Any type of duplication or excerpt from this document, also in electronic form, is not subject to the revision service of Manitowoc Crane Group Germany GmbH.

© Copyright reserved by

Manitowoc Crane Group Germany GmbH

27.05.2014

Industriegelände West D-26389 Wilhelmshaven, Germany Tel: [+49] (0) 44 21 294-0 Fax: [+49] (0) 44 21 294-301 The passing on or duplication of this document as well as the utilisation and disclosure of its contents are prohibited unless expressly permitted. Infringement will incur liability for compensation. All rights pertaining to registration of patent or utility model are reserved. The original language of this document is German.

3 113 112 en

Operating manual lattice extension GMK 3060i

The following chapters are contained in these operating instructions:

1 Important information 2 Transport dimensions and weights 3 8.7/15 m swing-away lattice extension 4 Auxiliary single-sheave boom top 5 Heavy load lattice extension

27.05.2014

6 Index

Operating manual lattice extension GMK 3060i

3 113 112 en

27.05.2014

3 113 112 en

Operating manual lattice extension GMK 3060i

1 Important information

1.1

About these operating instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 -

1

1.2

Basic safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 -

2

1.2.1

Warnings and symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 -

2

1.3

Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 -

3

1.4

Organizational measures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 -

5

1.5

Personnel qualifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 -

7

1.6

Safety instructions for truck crane work. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 -

8

27.05.2014

1

Operating manual lattice extension GMK 3060i

3 113 112 en

27.05.2014

3 113 112 en

Operating manual lattice extension GMK 3060i

Important information 1.1 About these operating instructions

1

Important information

1.1

About these operating instructions

Validity of these operating instructions

These operating instructions only apply to lattice extensions which were delivered by Manitowoc Crane Group Germany GmbH. In addition, for the operation of the truck crane with a lattice extension described in these operating instructions, all details in the included Operating instructions of the GMK 3060i for which the lattice extension was delivered from the factory, are applicable.

Prerequisites for assembly and operation

The lattice extensions described in these operating instructions may only be operated together with a GROVE truck crane GMK 3060i whose serial number is identical with the serial number that is marked on the lattice extensions.

Safety instructions

The operation of GMK 3060i with one of the lattice extensions described in these operating instructions is subject to: – all the basic safety instructions to be found in the subsequent section Basic safety instructions and – all the safety instructions contained in the supplied operating instructions of GMK 3060i.

References to other operating instructions

Cross references to other operating or maintenance instructions are shown in the following forms: GMK 3060i operating instructions, Part 2 Crane operation – Rigging work.

The number for the chapter on Rigging work is found at the front, on the second page of the operating instructions specified. or GMK 3060i operating instructions – Safe load indicator.

The corresponding page number can be found in the index, under the entry for Safe load indicator.

à

27.05.2014

à

Operating manual lattice extension GMK 3060i

3 113 112 en

1-1

Important information 1.2 Basic safety instructions

1.2

Basic safety instructions

1.2.1

Warnings and symbols The following definitions and symbols are used in the operating instructions to highlight particularly important information:

G S B O

This symbol indicates hazards related to the operation described which may cause personal injury. The type of danger (e.g. risk of fatal or nonfatal injury, or risk of crushing) is normally specified before the warning.

This symbol indicates dangers which could put objects at risk, e.g. damage to the truck crane, the load or the environment.

This symbol alerts you to situations where there is a risk of receiving an electric shock.

This symbol reminds you that you are working with substances which pose a risk to the environment. Take particular care. Further information on Maintenance handling substances that pose a risk to the environment; manual, Chapter Safety and environmental protection.

à

The vertical line to the left of the warning text indicates the following: this text, regardless of its length, relates to the warning symbol.

1-2

This symbol indicates that the topic is continued on the next page. Turn to the next page.

27.05.2014

H s

The hand with the pointing finger indicates passages that contain additional instructions and tips regarding truck crane operation.

3 113 112 en

Operating manual lattice extension GMK 3060i

Important information 1.3 Intended use

1.3

Intended use The truck crane GMK 3060i is constructed in accordance with the latest technology and the recognized safety regulations. Nevertheless, personal injury to the operator or a third party as well as damage to the crane and other property may occur during use.

The truck crane may only be modified with the consent of the manufacturer.

The truck crane GMK 3060i may only be used when in excellent working condition and for its intended purpose, and with due attention to safe operation and any possible hazards.

Malfunctions that may affect the safe operation of the unit are to be corrected immediately.

The GMK 3060i truck crane may only be operated at temperatures of between –25 and +40°C if it is not equipped with the relevant special equipment.

The GMK 3060i truck crane may only be used for the vertical lifting of loads, in the authorized rigging modes and using a hook block that is reeved to the hoist rope. The weight and centre of distribution of the loads must be known. Any other use of the crane is not considered to represent intended use.

The manufacturer is not liable for damage resulting from the improper or unauthorized use of the GMK 3060i truck crane. The user shall take full responsibility for any such use.

Intended use also entails – observing the complete crane documentation consisting of the operating instructions, the lifting capacity table, the outrigger pressure table and the safety manual – adhering to the inspection and maintenance requirements specified in the maintenance manual.

27.05.2014

s

Operating manual lattice extension GMK 3060i

3 113 112 en

1-3

Important information 1.3 Intended use

Improper use includes: – Transporting loads on the carrier – Pushing, pulling or lifting loads with the level adjustment system, the beams or the outrigger cylinders – Pushing, pulling or lifting loads off the ground using the slewing gear, the derricking gear or the telescoping mechanism – Pulling off fixed objects using the crane – Two-hook operation with the boom extension and two-hook operation on the main boom head without additional equipment – Defining RCL codes that do not correspond to the actual rigging mode – Working with an overridden RCL or overridden lifting limit switch – After RCL deactivation, increasing the radius by pulling the raised load at an angle (e.g. with a chain hoist) – Misuse of the outrigger pressure indicator as a safety function to prevent overturning after an RCL shutdown (outrigger pressure greater than 0 t) – Road driving in an unauthorized driving mode (axle load, dimension) – Moving the rigged crane in an unauthorized driving mode – Use of equipment that is not authorized for use with the crane – Transporting people in any way with the lifting tackle, upon the load, or in the crane cab while driving – Carrying passengers outside the driver's cab – Loading and unloading work, i.e. continuous operation without a sufficiently long break

27.05.2014

– Usage for any kind of sport or recreation event, especially for bungee jumping

1-4

3 113 112 en

Operating manual lattice extension GMK 3060i

Important information 1.4 Organizational measures

1.4

Organizational measures The operating instructions and the lifting capacity table should be kept in the truck crane for immediate access at all times, and must not be removed from the truck crane. You must have read and understood the operation and safety instructions in these operating instructions, and comply with them when working.

In addition to the operating instructions and the lifting capacity table, observe all general, statutory and otherwise applicable regulations concerning accident prevention and environmental protection. You must have read and understood these and must comply with them when working.

These could include: – How to deal with hazardous materials – Wearing personal protective equipment – Traffic regulations – All applicable regulations concerning the operation of a crane Ensure that those appointed to work on the truck crane are given the information required to carry out the work before starting operations. Instruct your employees (e.g. banksmen, slingers, rigging personnel) accordingly.

Ensure that the maintenance personnel possess the necessary expertise to safely operate the crane. Ensure that the maintenance personnel have access to the operating instructions.

Only properly trained or instructed personnel may carry out work on the truck crane.

Responsibilities related to crane operation, rigging, maintenance and repair work must be clearly defined.

Ensure that only the appointed employees operate the truck crane.

Do not leave long hair down or wear loose clothing or jewellery (including rings) when working with the crane. These could get caught or pulled into the unit and result in injury.

Use your personal protective equipment whenever necessary or prescribed.

Observe all safety and warning signs on the truck crane.

27.05.2014

s Operating manual lattice extension GMK 3060i

3 113 112 en

1-5

Important information 1.4 Organizational measures

Ensure that all safety and warning signs on the truck crane remain legible.

Note the operational organization on the site. Report your arrival to site management. Ask for the employee authorized to instruct you.

Familiarize yourself with the location and operation of the fire extinguishers on every site.

Note the fire alarm and fire fighting facilities on the site.

Should the operating behaviour of the truck crane change in such a manner that the safety conditions are affected, e.g. if you doubt the truck craneś operating safety, stop the machine immediately and inform the appropriate persons responsible.

Do not make any changes to the programmable control systems (e.g. the RCL).

Do not modify or mount attachments to the truck crane without the consent of the manufacturer, if such changes could affect the safety of the unit. This also applies to – The installation of safety devices – The adjustment of safety devices and valves Welding work on load-bearing parts may only be carried out by properly qualified personnel with the manufacturer's prior permission. To avoid any damage, especially to electronic parts, there are certain steps you must take before doing any welding work. You should therefore always consult Manitowoc Crane Care before doing any welding work.

Ensure that both the prescribed periods and the periods specified in the operating and maintenance instructions for regular testing, inspection and maintenance work are maintained.

Replace the hydraulic hose lines, or have them replaced, at the prescribed intervals, even if no safety defects are noticeable.

Replacement parts must fulfil the technical requirements prescribed by the manufacturer. Genuine spare parts always meet these requirements.

27.05.2014

It is imperative that appropriate service equipment be used when carrying out repair work.

1-6

3 113 112 en

Operating manual lattice extension GMK 3060i

Important information 1.5 Personnel qualifications

1.5

Personnel qualifications These operating instructions are not a training manual for prospective crane operators.

All descriptions are written explicitly for crane operators who have been trained to operate truck cranes.

Employees in training may only operate the truck crane under strict supervision.

Only reliable personnel may operate the truck crane.

As a truck crane operator you are obliged to fulfil a number of requirements: – You must possess a driving licence for this type of vehicle that is valid in the country in which you are working.

– You must have general knowledge of crane operation and any qualifications that may be required by the country in which you are working.

– You must be familiar with and have understood the operating instructions.

– You must be familiar with and have understood the accident prevention regulations.

– You must fulfil all physical and mental requirements for truck crane operation, e.g. perfect sight and hearing and the ability to react quickly.

Please refer to the section in the Safety manual titled You as crane driver and operator.

Only experienced personnel familiar with the applicable accident prevention regulations are authorized to sling loads and to train crane operators.

Your responsibilities as a crane operator (including those concerning traffic regulations) must be clearly defined. You must be in a position to refuse to carry out any instructions given to you by a third party that violate safety regulations.

Only trained personnel with special knowledge and experience in the fields of hydraulics, pneumatics and electrical equipment may carry out maintenance work on the truck crane.

27.05.2014

Manitowoc Crane Group Germany GmbH conducts general and type-specific crane operator courses and technical courses.

Operating manual lattice extension GMK 3060i

3 113 112 en

1-7

Important information 1.6 Safety instructions for truck crane work

1.6

Safety instructions for truck crane work Carefully select a safe site for the truck crane to stand from where you can work safely.

Check over the truck crane before beginning crane work. Check the condition of the truck crane carefully using the checklists in the operating instructions. Do not assume that everything is in working order simply because it was in working order when work was last completed.

Check daily before starting to work with the crane that all guards and safety devices are correctly fitted and that they are all in a proper condition.

Check the safety devices each day before beginning work (RCL, lifting limit switch, dead man's switch, emergency stop switch for crane control).

Use the appropriate access aids when carrying out overhead rigging or maintenance work. Do not use parts of the crane as access aids.

Walk only on those machine parts which are equipped with appropriate steps and railings and therefore guarantee safety.

Use a suitable safety harness when walking on other surfaces – this also applies to sanded surfaces.

During rigging and maintenance work on machine sections above body height which have no apparatus for accessing them, always use the extension ladder supplied (e.g. when reeving the hoist rope on the boom head).

Keep all handles, steps, step treads and ladders free of dirt, snow and ice.

Check all operating and control elements in the crane cab before starting the diesel engine.

Monitor all warning and indicator lamps as well as the control instruments when the engine is started.

Make sure that there are no unauthorized people in the vicinity of or on the truck crane when rigging or during crane work. Secure the danger zone using cordons and mark the zone as such.

27.05.2014

When lifting a load, raise the boom to balance out the increase in radius caused by the boom bending so that the load is lifted up vertically and does not drag, injure helpers or fall into the hoist rope diagonally (e.g. from a vehicle or scaffolding). Inform banksmen and helpers about this as well.

1-8

3 113 112 en

Operating manual lattice extension GMK 3060i

Important information 1.6 Safety instructions for truck crane work

Before turning the superstructure, support the truck crane with the outrigger span required for the currently rigged counterweight.

Ensure that the truck crane is horizontally aligned before carrying out crane work.

Only use equipment (counterweight sections, lattice extensions) that belongs to your truck crane. Both the truck crane and the equipment must have the same serial number.

Simultaneously lifting loads with two cranes is particularly dangerous. Use extreme caution when carrying out this type of work.

When work is interrupted, always put the load down and never leave the truck crane if a load is raised.

Lock the truck crane when you leave the cab to prevent unauthorized use.

27.05.2014

Crane work carried out in the vicinity of live electrical cables as well as oil, gas or other supply lines is dangerous and requires that special precautionary measures be taken. Please refer to the section titled Crane operation under special operating conditions in the Safety manual, and observe the relevant national regulations.

Operating manual lattice extension GMK 3060i

3 113 112 en

1-9

Important information 1.6 Safety instructions for truck crane work

27.05.2014

Blank page

1 - 10

3 113 112 en

Operating manual lattice extension GMK 3060i

2 Transport dimensions and weights

2.1

Swing-away lattice extension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 -

1

2.2

Auxiliary single-sheave boom top . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 -

1

2.3

Heavy load lattice extension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 -

1

27.05.2014

2

Operating manual lattice extension GMK 3060i

3 113 112 en

27.05.2014

3 113 112 en

Operating manual lattice extension GMK 3060i

Transport dimensions and weights 2.1 Swing-away lattice extension

2

Transport dimensions and weights

2.1

Swing-away lattice extension Length x width x height in m

Weight in kg

15 m swing-away lattice extension, complete, folded

8.9 x 1.10 x 1.35

990

Section 1

8.9 x 0.55 x 1.35

720

Section 2

6.5 x 0.50 x 0.55

270

Designation

The values apply for the hydraulically set lattice extensions and for the manually inclinable lattice extension.

2.2

Description

Length x width x height in m

Weight in kg

Auxiliary single-sheave boom top complete with pins

1.00 x 0.40 x 1.00

60

Heavy load lattice extension Description

Length x width x height in m

Weight in kg

Heavy load lattice extension approx. 2 m

2.30 x 0.90 x 1.40

330

27.05.2014

2.3

Auxiliary single-sheave boom top

Operating manual lattice extension GMK 3060i

3 113 112 en

2-1

Transport dimensions and weights 2.3 Heavy load lattice extension

27.05.2014

Blank page

2-2

3 113 112 en

Operating manual lattice extension GMK 3060i

3 8.7/15 m swing-away lattice extension

3.1

Validity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 -

1

3.2

Additional operating and display elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 -

1

3.2.1 3.2.2 3.2.3

In the crane cab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Operating and display elements on the hand-held control . . . . . . . . . . . . . . . . 3 Operating elements on the swing-away lattice extension . . . . . . . . . . . . . . . . 3 -

2 5 6

3.3

Identification of the swing-away lattice extension . . . . . . . . . . . . . . . . . . . . . . . . 3 -

7

3.4

Composition of the swing-away lattice extension. . . . . . . . . . . . . . . . . . . . . . . . . 3 -

9

3.5

Centres of gravity for slinging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 10

3.6

Checklists for rigging work. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 11

3.6.1 3.6.2 3.6.3 3.6.4 3.6.5

Overview of the required rigging work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 11 CHECKLIST: Installing 8.7/15 m swing-away lattice extension . . . . . . . . . . . . . 3 - 12 CHECKLIST: Removing 8.7/15 m swing-away lattice extension . . . . . . . . . . . . 3 - 14 CHECKLIST: Rigging the 8.7/15 m swing-away lattice extension . . . . . . . . . . . 3 - 19 CHECKLIST: Unrigging the 8.7/15 m swing-away lattice extension . . . . . . . . . 3 - 25

3.7

Description of rigging work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 31

3.7.1 3.7.2 3.7.3 3.7.4 3.7.5 3.7.6 3.7.7 3.7.8 3.7.9 3.7.10 3.7.11 3.7.12 3.7.13 3.7.14 3.7.15 3.7.16 3.7.17 3.7.18 3.7.19

Preparing the truck crane for rigging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 31 Checking the transport condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 33 Checking the anti-twist device on the hose drum . . . . . . . . . . . . . . . . . . . . . . . . 3 - 39 Establishing/disconnecting the hydraulic connection . . . . . . . . . . . . . . . . . . . . 3 - 41 Guides and holders for the hydraulic hoses . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 43 Connections with folded lattice extension. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 45 Securing/releasing section 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 53 Connecting/disconnecting the slewing connection . . . . . . . . . . . . . . . . . . . . . . 3 - 55 Connections on the left and right of the main boom head . . . . . . . . . . . . . . . . 3 - 57 Swivelling the lattice extension when rigging . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 61 Establishing/releasing connections on the lattice extension . . . . . . . . . . . . . . . 3 - 66 Electrical connections on the lattice extension . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 69 Unfolding/folding the deflection sheave . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 72 Positioning/removing the hoist rope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 74 Installing/removing the lifting limit switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 76 Installing/removing the anemometer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 79 Installing/removing the air traffic control light . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 81 Derricking the lattice extension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 83 Setting the angle – with the auxiliary crane . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 86

27.05.2014

3

s Operating manual lattice extension GMK 3060i

3 113 112 en

Setting the angle – without the auxiliary crane. . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 88 Transportation on a separate vehicle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 94

3.8

Operation with the lattice extension. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 95

3.8.1 3.8.2 3.8.3 3.8.4 3.8.5 3.8.6

Setting the RCL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 96 Derricking the main boom. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 98 Telescoping with rigged lattice extension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 99 Information about the RCL shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 100 Procedure if permissible wind speed is exceeded . . . . . . . . . . . . . . . . . . . . . . . 3 - 101 Information about the main boom operation when the lattice extension is folded/rigged . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 102

3.9

Turning loads with the lattice extension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 105

3.9.1 3.9.2

Setting the RCL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 105 Turning a load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 107

3.10

Driving with rigged crane with a rigged lattice extension . . . . . . . . . . . . . . . . . . 3 - 109

3.10.1 3.10.2 3.10.3

Driving route. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 110 Boom positions and axle loads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 110 Driving the rigged crane . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 114

3.11

Finding and eliminating malfunctions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 115

3.12

Maintenance work. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 117

3.12.1 3.12.2 3.12.3

Modules in need of protection during cleaning work. . . . . . . . . . . . . . . . . . . . . 3 - 117 Maintenance work M1, monthly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 118 Maintenance work M12, every twelve months . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 119

27.05.2014

3.7.20 3.7.21

3 113 112 en

Operating manual lattice extension GMK 3060i

8.7/15 m swing-away lattice extension 3.1 Validity

3

8.7/15 m swing-away lattice extension

3.1

Validity This chapter applies to the hydraulically derricking lattice extension and to the manually inclinable lattice extension.

There is a hydraulic cylinder on the hydraulically derricking lattice extension (1).

Rigging work that applies only to this lattice extension is indicated in the checklists with the symbol (1.1).

There is a angle piece on the manually inclinable lattice extension (2).

Rigging work that applies only to this lattice extension is indicated in the checklists with the symbol (2.1).

H 3.2

All illustrations in this chapter show the GMK 3055. Rigging work on the GMK 3060i is carried out in the same way.

Additional operating and display elements When the GMK 3060i is equipped with swing-away lattice extension, certain operating and display elements in the crane cab also apply to the operation of the lattice extension. The following sections describe: – all operating and display elements in the crane cab required for the operation of the lattice extension.

27.05.2014

– all operating and display elements on the hand-held control required for the operation of the lattice extension.

– the operating elements located directly on the swing-away lattice extension.

Operating manual lattice extension GMK 3060i

3 113 112 en

3-1

8.7/15 m swing-away lattice extension 3.2 Additional operating and display elements

3.2.1

In the crane cab There are additional operating and display elements in the crane cab – on the right control panel, – on the CCS control unit (Crane-Control-System) and – on the RCL control unit (Rated-Capacity-Limiter).

On the right control panel

Only for the hydraulically derricking lattice extension.

Derricking lattice extension on/off There is a lamp in the button.

– Press once:

– Bright lamp – derricking gear of lattice extension on – Dim lamp – derricking gear of lattice extension off

à p. 3 - 85 Control lever – To the left:

– Raise – Lift the lattice extension

– To the right: – Lower – Lower lattice extension

à p. 3 - 85

On the CCS control unit Display of derricking gear of lattice extension (Only for the hydraulically derricking lattice extension) – Green:

Derricking gear of the lattice extension on

– Red:

Derricking gear of the lattice extension off

27.05.2014

à p. 3 - 85

3-2

3 113 112 en

Operating manual lattice extension GMK 3060i

8.7/15 m swing-away lattice extension 3.2 Additional operating and display elements

On the RCL control unit

With hydraulically derricking lattice extension Menu for entering rigging mode Boom system entry 1 Boom system selection 2 Main boom 3 Lattice extension 3.1 Length

à p. 3 - 97 Monitoring menu Boom system display 1 Main boom display 2 Display for main boom with lattice extension 2.1 Angle 2.2 Length

à p. 3 - 97

For manually inclinable lattice extension Menu for entering rigging mode Boom system entry 1 Boom system selection 2 Main boom 3 Lattice extension 3.1 Angle 3.2 Length

à p. 3 - 97

27.05.2014

s

Operating manual lattice extension GMK 3060i

3 113 112 en

3-3

8.7/15 m swing-away lattice extension 3.2 Additional operating and display elements

Monitoring menu Boom system display 1 Main boom display 2 Display for main boom with lattice extension

27.05.2014

à p. 3 - 97

3-4

3 113 112 en

Operating manual lattice extension GMK 3060i

8.7/15 m swing-away lattice extension 3.2 Additional operating and display elements

3.2.2

Operating and display elements on the hand-held control Only for the hydraulically derricking lattice extension.

The button (1) derrick lattice extension is active if the swing-away lattice is electrically connected.

Pre-select and then press the required combination of buttons.

– Pre-selection on:

Press button once – lamp (1) lights up – pre-selection on until another pre-selection is made

– Pre-selection off:

Press a non-allocated combination of buttons

– Pre-selected function on

Press the required button combination

– Pre-selected function off

Release one or both the buttons

To raise the lattice extension: Press button combination shown

To lower the lattice extension: Press button combination shown

Increase pressure on button

– Slower movement:

Decrease pressure on button

27.05.2014

– Faster movement:

Operating manual lattice extension GMK 3060i

3 113 112 en

3-5

8.7/15 m swing-away lattice extension 3.2 Additional operating and display elements

3.2.3

Operating elements on the swing-away lattice extension

1 Raise swing-away lattice extension 2 Lower swing-away lattice extension

27.05.2014

The movement is carried out as long as the button is pushed down or a switch-off point has been reached.

3-6

3 113 112 en

Operating manual lattice extension GMK 3060i

8.7/15 m swing-away lattice extension 3.3 Identification of the swing-away lattice extension

3.3

Identification of the swing-away lattice extension The swing-away lattice extension is designed for the truck crane with which it was delivered. The sections of the swing-away lattice extension belonging to the truck crane have the same serial number as the truck crane.

The following sections are identified by the serial number: – Section 1 (8.7 m) on the fixed section, – Section 1 (8.7 m) on the inclinable section, – Section 2 (6.3 m).

S H

S

Risk of accidents during operation with non-modified swing-away lattice extension Only operate the truck crane with those sections of the swing-away lattice extension which have the same serial number as the crane.

The RCL is set only for this swing-away lattice extension.

This prevents malfunctions and damage.

For technical reasons a truck crane may only be set with one swing-away lattice extension.

If you wish to use the swing-away lattice extension on several truck cranes, the parts of the swing-away lattice extension must be adjusted for these cranes and labelled with all serial numbers.

Risk of accidents if not adjusted correctly.

The adjustment of the swing-away lattice extension may only be carried out

by Manitowoc Crane Care.

27.05.2014

s

Operating manual lattice extension GMK 3060i

3 113 112 en

3-7

8.7/15 m swing-away lattice extension 3.3 Identification of the swing-away lattice extension

Serial number on section 1

Section 1 consists of a fixed section and an inclinable section.

On the inclinable section the serial number (1) is at the rear on a sheet before the pivot point.

The serial number (2) is at the bottom lefthand side on the lower sheet of the fixed section.

Serial number on section 2

27.05.2014

On section 2 the serial number (1) is at the rear on the plate in the top chord.

3-8

3 113 112 en

Operating manual lattice extension GMK 3060i

8.7/15 m swing-away lattice extension 3.4 Composition of the swing-away lattice extension

3.4

Composition of the swing-away lattice extension

8.7 m swing-away lattice extension Section 1 (8.7 m)

15 m swing-away lattice extension Section 2 (6.3 m)

Section 1 (8.7 m)

H

The length data for the swing-away lattice extension of 8.7 m and 15 m corresponds to the distance between the centre of the locking pin (on the main boom head) and the frontedge of the head sheave.

That is why the length data of the components in the Transport dimensions and weights section and their sums do not correspond to the specified p. 2 - 1. lengths of lattice extension;

à

27.05.2014

H

The Lifting capacity tables primarily contain the term Swing-away lattice extension. This term will only be used later in this chapter, when a length specification is necessary.

When no length data is necessary (e.g. for rigging work), the term Lattice extension is only used when the text needs to be as short as possible.

Operating manual lattice extension GMK 3060i

3 113 112 en

3-9

8.7/15 m swing-away lattice extension 3.5 Centres of gravity for slinging

3.5

Centres of gravity for slinging When you sling the lattice extension or an component, then you have to observe the different centres of gravity so that the sections hang horizontally.

G

Risk of accidents due to falling lattice extension sections Always observe relevant centres of gravity shown in following table when slinging and use suitable slinging material with sufficient load bearing caTransport dimensions and weights, p. 2 - 1. pacity; In this way you prevent the attached sections from slipping out, falling and causing injury during installation or removal.

à

The stop points on section 1 are labelled with signs (1).

The connection eyes (2) are on section 2.

• Use: – The stop points (1) for section 1 or section 1 with section 2. Use the different connection points depending on whether section 2 is folded or swung out.

3 - 10

3 113 112 en

Operating manual lattice extension GMK 3060i

27.05.2014

– The connection eyes (2) for section 2.

8.7/15 m swing-away lattice extension 3.6 Checklists for rigging work

3.6

Checklists for rigging work

3.6.1

Overview of the required rigging work There are different initial states for rigging the lattice extension, depending on whether – the lattice extension is folded at the side of the main boom or – the lattice extension was removed for on-road driving (information about Operating instructions GMK 3060i – Driving modes. the driving modes;

à

The following table shows you which checklist describes the required rigging work for your initial state.

Initial state Before crane operation

à

The lattice extension is on the side of the main boom.

Checklist for rigging; p. 3 - 19

The lattice extension was removed completely.

Checklist for installation; p. 3 - 12

The lattice extension must be folded to the side of the main boom.

Checklist for unrigging; p. 3 - 25

The lattice extension is to be removed for on-road driving.

Checklist for removal; p. 3 - 14

à à à

27.05.2014

After crane operation

Corresponding rigging work

Operating manual lattice extension GMK 3060i

3 113 112 en

3 - 11

8.7/15 m swing-away lattice extension 3.6 Checklists for rigging work

3.6.2

CHECKLIST: Installing 8.7/15 m swing-away lattice extension

H

This checklist is not equivalent to complete operating instructions. There are accompanying instructions which are indicated by cross-references.

Observe the warning and safety information given there.

Prerequisites: – The truck crane is on outriggers or the main boom has been placed on the boom rest.

– An auxiliary crane is available.

1. With hydraulically derricking lattice extension, check if the anti-twist device on the hose drum is released and, if necessary, release the antitwist device; Checking the anti-twist device on the hose drum, p. 3 - 39.

à

2. Check the transport condition of the swing-away lattice extension; Transport condition with removed lattice extension, p. 3 - 38.

à

3. Sling the lattice extension on auxiliary crane and fasten the guide ropes; Centres of gravity for slinging, p. 3 - 10.

à

4. Lift lattice extension with auxiliary crane in front of the main boom and create a slewing connection between section 1 and the main boom head; Creating a slewing connection, p. 3 - 55.

27.05.2014

à

3 - 12

3 113 112 en

Operating manual lattice extension GMK 3060i

8.7/15 m swing-away lattice extension 3.6 Checklists for rigging work

G

Danger of becoming trapped due to swinging lattice extension Always secure the lattice extension against swinging with the auxiliary crane and the guide ropes before you establish the hydraulic or electrical connection.

This will prevent the lattice extension from swinging inadvertently on the side of the main boom and possibly crushing you.

5. With the hydraulically derricking lattice extension, establish the hydraulic connection between the lattice extension and the main boom; Establishing/disconnecting the hydraulic connection, p. 3 - 41.

à

6. Establish electrical connection between section 1 and the main boom; Establishing the electrical connection, p. 3 - 69.

à

7. Fasten the guide ropes to the front of section 1.

8. The CHECKLIST: Unrigging the 8.7/15 m swing-away lattice extension from p. 3 - 28 describes further rigging work dealing with lateral Point 21; folding.

à

9. Further rigging work dealing with rigging the 8.7 m swing-away lattice extension or the 15 m swing-away lattice extension is described in the CHECKLIST: Rigging the 8.7/15 m swing-away lattice extension from p. 3 - 21.

Point 13.; 27.05.2014

à

Operating manual lattice extension GMK 3060i

3 113 112 en

3 - 13

8.7/15 m swing-away lattice extension 3.6 Checklists for rigging work

3.6.3

CHECKLIST: Removing 8.7/15 m swing-away lattice extension

H

This checklist is not equivalent to complete operating instructions. There are accompanying instructions which are indicated by cross-references.

Observe the warning and safety information given there.

Prerequisites: – The truck crane is on outriggers or the main boom has been placed on the boom rest.

– An auxiliary crane is available.

For a rigged lattice extension

H

This checklist only applies when the lattice extension is rigged. If the lattice extension is folded up at the side of the main boom, another checklist app. 3 - 16. plies;

à

If you want to transport the lattice extension while it is folded, but only section 1 is swung out and section 2 is locked to the main boom, you should CHECKLIST: Unrigging the 8.7/15 m first unrig the lattice extension ( p. 3 - 16). swing-away lattice extension, p. 3 - 25) and then remove it (

à

à

1. Carry out all rigging work contained in the CHECKLIST: Unrigging the 8.7/15 m swing-away lattice extension up to and including point 18; p. 3 - 28.

à

2. Disconnect electrical connection between section 1 and the main Establishing the electrical connection, p. 3 - 69. boom;

à

3. With the hydraulically derricking lattice extension, disconnect the hydraulic connection between the lattice extension and the main boom; Establishing/disconnecting the hydraulic connection, p. 3 - 41.

27.05.2014

à

3 - 14

3 113 112 en

Operating manual lattice extension GMK 3060i

8.7/15 m swing-away lattice extension 3.6 Checklists for rigging work

4. Slinging lattice extension on auxiliary crane; slinging, p. 3 - 10.

à Centres of gravity for

5. Remove the connection on the right and left between the main boom and section 1; Releasing connections, p. 3 - 58.

à

6. Remove the slewing connection between section 1 and main boom head and set down the lattice extension onto a separate vehicle; Creating a slewing connection, p. 3 - 55, Transportation on a separate vehicle, p. 3 - 94.

à à

7. If section 2 is still installed on the main boom and is also to be removed: p. 3 - 10.

– Sling section 2, centre of gravity;

à

– Disconnect the connection between section 2 and the main boom in the Middle area; p. 3 - 50.

à

– Disconnect the connection between section 2 and the main boom in the Front 2 area; p. 3 - 48.

à

– Set down section 2 onto the separate vehicle.

8. Check the transport condition of the swing-away lattice extension; Transport condition with removed lattice extension, p. 3 - 38.

à

27.05.2014

s

Operating manual lattice extension GMK 3060i

3 113 112 en

3 - 15

8.7/15 m swing-away lattice extension 3.6 Checklists for rigging work

For a folded lattice extension

This checklist only applies when the lattice extension is folded at the side of the main boom. When the lattice extension is rigged, another p. 3 - 14. checklist applies;

à

1. For a hydraulically derricked lattice extension: If necessary, disconnect the hydraulic connection between the lattice Establishing/disconnecting the hydraulic extension and the main boom; connection, p. 3 - 41.

à

2. If necessary, disconnect electrical connection between section 1 and the main boom; Separating the electrical connection, p. 3 - 70.

à

3. Sling the lattice extension on auxiliary crane and fasten a guide rope; Centres of gravity for slinging, p. 3 - 10.

à

4. When the 8.7 m swing-away lattice extension is folded to the side: – Disconnect the connection between section 1 and the main boom in the Middle area; p. 3 - 50.

– Disconnect the connection between section 1 and the main boom in p. 3 - 46. the Front 1 area;

à

à

5. When the 15 m swing-away lattice extension is folded to the side: – Check if the connection between section 1 and section 2 is established in the Rear area; p. 3 - 52.

– Check if the connection between section 1 and section 2 is estabp. 3 - 47. lished in the Front 2 area;

à

27.05.2014

à

3 - 16

3 113 112 en

Operating manual lattice extension GMK 3060i

8.7/15 m swing-away lattice extension 3.6 Checklists for rigging work

6. When the 15 m swing-away lattice extension is folded to the side: – Disconnect the connection between section 1 and the main boom in the Front 1 area; p. 3 - 46.

– Disconnect the connection in the Middle area. Depending on the current rigging mode, disconnect the connection between the main p. 3 - 50. boom and section 1 or section 2;

à

à

7. Remove the slewing connection between section 1 and main boom head and set down the lattice extension onto a separate vehicle; Releasing a slewing connection, p. 3 - 56, Transportation on a separate vehicle, p. 3 - 94.

à à

8. Check the transport condition of the swing-away lattice extension; Transport condition with removed lattice extension, p. 3 - 38.

27.05.2014

à

Operating manual lattice extension GMK 3060i

3 113 112 en

3 - 17

8.7/15 m swing-away lattice extension 3.6 Checklists for rigging work

27.05.2014

Blank page

3 - 18

3 113 112 en

Operating manual lattice extension GMK 3060i

8.7/15 m swing-away lattice extension 3.6 Checklists for rigging work

3.6.4

CHECKLIST: Rigging the 8.7/15 m swing-away lattice extension

H

This checklist is not a complete instruction manual. There are accompanying instructions which are indicated by cross-references. Observe the warning and safety instructions given there.

1. Prepare the truck crane for rigging the swing-away lattice extension; Prerequisites for rigging, p. 3 - 31.

à

2. For a hydraulically derricked lattice extension: Establish the hydraulic connection between the lattice extension and the main boom; Establishing/disconnecting the hydraulic connection, p. 3 - 41.

à

3. Establish electrical connection between section 1 and the main boom; Establishing the electrical connection, p. 3 - 69.

à

4. Check if the lattice extension was unrigged properly and is in transport Transport condition with lattice extension folded at the side, condition; p. 3 - 34.

à

5. Establish a slewing connection between section 1 and the main boom Creating a slewing connection, p. 3 - 55. head;

à

27.05.2014

s

Operating manual lattice extension GMK 3060i

3 113 112 en

3 - 19

8.7/15 m swing-away lattice extension 3.6 Checklists for rigging work

6. Secure the lattice extension on the main boom with guide rope; Securing lattice extension with cord, p. 3 - 32.

à

7. This point only applies to the rigging of the 8.7 m swing-away lattice extension, when only section 1 is installed.

Disconnect the connection in the Middle area between section 1 and the run-up rail; Releasing connections in the middle area, p. 3 - 50.

à

8. This point only applies to the rigging of the 8.7 m swing-away lattice extension, when section 2 is also installed.

– Establish the connection between section 2 and the main boom in the Front 2 area; p. 3 - 48.

– Establish the connection between section 2 and the run-up rail in the Middle area; p. 3 - 50.

– Secure lattice extension in the middle area of section 2; p. 3 - 53.

– Disconnect the connection between section 2 and section 1 in the Rear area; p. 3 - 52.

à

à

à

à

9. This point only applies when rigging the 15 m swing-away lattice extension.

Disconnect the connection in the Middle area between section 1 and the run-up rail; p. 3 - 50.

à

10. Disconnect the connection between section 1 and the main boom in the Front 1 area; Releasing the connection, p. 3 - 46.

27.05.2014

à

3 - 20

3 113 112 en

Operating manual lattice extension GMK 3060i

8.7/15 m swing-away lattice extension 3.6 Checklists for rigging work

11. This point only applies for the hydraulically derricking lattice extension.

When the 15 m swing-away lattice extension is rigged, raise the lattice extension as far as possible; Derricking the lattice extension, p. 3 - 83.

Section 2 must then be located over the holder on the run-up rail; Securing/releasing section 2, p. 3 - 53.

à

à

12. When the 15 m swing-away lattice extension is rigged, release section 2 in the middle area; p. 3 - 53.

à

13. Swing the lattice extension in front of the main boom head; rigging – section 1, p. 3 - 61.

à When

14. Pin section 1 onto the main boom head, on left-hand side; Establishing connections, p. 3 - 57.

à

15. Pin section 1 onto the main boom head, on the right-hand side; at the same time, release the bearing points, if necessary; Establishing connections, p. 3 - 57, Relieving the connecting points, p. 3 - 60.

à à

16. When using the hydraulically derricking lattice extension, hang the hydraulic hoses on the front holder and lay them on the guide sheaves; When rigging, p. 3 - 44.

à

27.05.2014

s Operating manual lattice extension GMK 3060i

3 113 112 en

3 - 21

8.7/15 m swing-away lattice extension 3.6 Checklists for rigging work

H

When the 8.7 m swing-away lattice extension is rigged – proceed as from point 22; p. 3 - 23.

à

17. If section 2 was transported on a separate vehicle, install section 2 before section 1: – Sling section 2 onto the auxiliary crane, centre of gravity; p. 3 - 10.

– Lift section 2 in front of section 1 and pin it there; p. 3 - 66.

à

à

After installing section 2, proceed as from point 22.

18. When section 2 is folded on the side of section 1, fasten the guide rope to the head of section 2.

19. Disconnect the connection between section 2 and section 1 and swing When rigging – section 2, p. 3 - 63. section 2 in front of section 1;

à

20. Establish the connection on the left between section 2 and section 1; Establishing/releasing connections on the lattice extension, p. 3 - 66.

à

21. Establish electrical connection between section 1 and section 2; Establishing the electrical connection, p. 3 - 69.

27.05.2014

à

3 - 22

3 113 112 en

Operating manual lattice extension GMK 3060i

8.7/15 m swing-away lattice extension 3.6 Checklists for rigging work

22. Fold out deflection sheaves on section 1; tion sheave, p. 3 - 72.

à Unfolding/folding the deflec-

23. Position the hoist rope on the lattice extension; the hoist rope, p. 3 - 74.

24. Install the anemometer;

à Positioning/removing

à Installing/removing the anemometer, p. 3 - 79.

25. Installing the lifting limit switch; switch, p. 3 - 76.

à Installing/removing the lifting limit

26. When using a manually inclinable lattice extension, set the angle at 20° or 40°; Setting the angle – with the auxiliary crane, p. 3 - 86.

Setting the angle – without the auxiliary crane, p. 3 - 88.

à à

27. Reeve the hoist rope; p. 3 - 75.

à Possible reeving methods on the lattice extension,

27.05.2014

s Operating manual lattice extension GMK 3060i

3 113 112 en

3 - 23

8.7/15 m swing-away lattice extension 3.6 Checklists for rigging work

28. Attach the lifting limit switch weight and place it around the moist rope; Operating instructions GMK 3060i, Part 2 Superstructure – Rigging work.

à

29. Check the alignment of the truck crane and, if necessary, position the truck crane so that it is level.

30. Enter the current rigging mode with the rigged swing-away lattice; Setting the RCL, p. 3 - 96.

à

31. Enter current reeving;

à Setting the RCL, p. 3 - 105.

Further work steps with swing-away lattice extension:

à

– Raise main boom; p. 3 - 98.

– Telescope main boom; p. 3 - 99.

27.05.2014

à

3 - 24

3 113 112 en

Operating manual lattice extension GMK 3060i

8.7/15 m swing-away lattice extension 3.6 Checklists for rigging work

3.6.5

CHECKLIST: Unrigging the 8.7/15 m swing-away lattice extension

H

This checklist is not a complete instruction manual. There are accompanying instructions which are indicated by cross-references. Observe the warning and safety instructions given there.

1. Prepare the truck crane for unrigging; p. 3 - 31.

à Prerequisites for unrigging,

2. Enter RCL code according to the Lifting capacity table for the actual rigging status of the truck crane with the rigged lattice extension; Setting the RCL, p. 3 - 96.

à

3. Retract the main boom completely; tension, p. 3 - 99.

à Telescoping with rigged lattice ex-

4. This point only applies for the hydraulically derricking lattice extension.

– Completely retract the lattice extension; Derricking the lattice extension, p. 3 - 83.

à

– Lowering the boom to horizontal position;

à p. 3 - 98.

5. This item only applies to the manually inclinable lattice extension.

Lower the main boom until the lattice extension is positioned at the correct height for unreeving of the hook block.

6. Remove the lifting limit switch weight and remove the lifting limit switch; Installing/removing the lifting limit switch, p. 3 - 76.

27.05.2014

à

s Operating manual lattice extension GMK 3060i

3 113 112 en

3 - 25

8.7/15 m swing-away lattice extension 3.6 Checklists for rigging work

7. Unreeve the hoist rope from the hook block and remove it from the lattice extension; Positioning/removing the hoist rope, p. 3 - 74.

à

8. This item only applies to the manually inclinable lattice extension.

– At angles of 20° or 40°, unreeve the hook block before setting the angle to 0°.

Setting the angle – with the auxiliary crane, p. 3 - 86 Setting the angle – without the auxiliary crane, p. 3 - 88.

à à

9. Remove the anemometer; p. 3 - 79.

à Installing/removing the anemometer,

10. Fold up the deflection sheave on section 1; flection sheave, p. 3 - 72.

à Unfolding/folding the de-

11. Remove hoist rope and reel it up to the main boom head; Positioning/removing the hoist rope, p. 3 - 74.

à

à

27.05.2014

H

When the 8.7 m swing-away lattice extension is unrigged – proceed as from point 17.; p. 3 - 27.

3 - 26

3 113 112 en

Operating manual lattice extension GMK 3060i

8.7/15 m swing-away lattice extension 3.6 Checklists for rigging work

12. Disconnect electrical connection between section 1 and section 2; Separating an electrical connection, p. 3 - 71.

à

13. Fasten the guide ropes to the front of section 2.

14. If section 2 is to be removed: – Sling section 2 onto the auxiliary crane, centre of gravity; p. 3 - 10.

– Remove the locking pins between section 2 and section 1; p. 3 - 66.

– Set down section 2 onto the separate vehicle.

After removing section 2, proceed as from point 17.

à à

15. Disconnect the connection on the left between section 2 and section 1; Establishing/releasing connections on the lattice extension, p. 3 - 66.

à

16. Swing section 2 to the side of section 1 and establish the connection between section 1 and section 2; When unrigging – section 2, p. 3 - 64.

à

27.05.2014

17. Fasten the guide ropes to the front of section 1.

s Operating manual lattice extension GMK 3060i

3 113 112 en

3 - 27

8.7/15 m swing-away lattice extension 3.6 Checklists for rigging work

18. When using the hydraulically derricking lattice extension, take the hydraulic hoses out of the guide sheaves; When unrigging – Before folding, p. 3 - 43.

à

19. Disconnect the connection between section 1 and the main boom head at the right of the main boom head. Only detach the two inner pins, the Releasing connections, p. 3 - 58. slewing connection remains set;

à

20. Disconnect the connection between section 1 and the main boom head at the left of the main boom head; Connecting/disconnecting the slewing connection, p. 3 - 55.

à

21. Swinging the lattice extension with the guide rope on the side onto the main boom; When unrigging – section 1, p. 3 - 62.

à

22. Lower the hydraulically derricking lattice extension so that it is positioned on the run-up rail.

– Secure section 2 when unrigging the 15 m swing-away lattice exten(A) – Securing section 2, p. 3 - 53. sion;

27.05.2014

à

3 - 28

3 113 112 en

Operating manual lattice extension GMK 3060i

8.7/15 m swing-away lattice extension 3.6 Checklists for rigging work

23. This point only applies to the unrigging of the 8.7 m swing-away lattice extension, when only section 1 is installed.

– Establish the connection between section 1 and the run-up rail in the Middle area; p. 3 - 49.

– Establish the connection between section 1 and the main boom in p. 3 - 46. the Front 1 area;

à

à

24. This point only applies to the unrigging of the 8.7 m swing-away lattice extension, when section 2 is also installed.

– Establish the connection between section 1 and section 2 in the Rear area; p. 3 - 51.

– Establish the connection between section 1 and the run-up rail in the Middle area; p. 3 - 49.

– Establish the connection between section 1 and the main boom in p. 3 - 46. the Front 1 area;

à

à

à

25. This point only applies when unrigging the 15 m swing-away lattice extension.

– Establish the connection between section 1 and the run-up rail in the Middle area; p. 3 - 49.

– Establish the connection between section 1 and the main boom in the Front 1 area; p. 3 - 46.

à

à

26. When using the hydraulically derricking lattice extension, hang the hydraulic hoses in the holder on the hose drum; When unrigging – After folding, p. 3 - 44.

à

27. With the hydraulically derricking lattice extension, disconnect the hydraulic connection between the lattice extension and the main boom; Establishing/disconnecting the hydraulic connection, p. 3 - 41.

à

27.05.2014

s

Operating manual lattice extension GMK 3060i

3 113 112 en

3 - 29

8.7/15 m swing-away lattice extension 3.6 Checklists for rigging work

28. Disconnect electrical connection between section 1 and the main boom; Separating the electrical connection, p. 3 - 70.

à

29. Disconnect the slewing connection between section 1 and the main boom head; Creating a slewing connection, p. 3 - 55.

This point may not apply if the rigged lattice extension will be used for the next job and it hasn't been telescoped in the meantime.

à

30. Enter the current rigging mode;

à Setting the RCL, p. 3 - 96.

31. Check whether the lattice extension is in transport condition; Transport condition with lattice extension folded at the side, p. 3 - 34.

27.05.2014

à

3 - 30

3 113 112 en

Operating manual lattice extension GMK 3060i

8.7/15 m swing-away lattice extension 3.7 Description of rigging work

3.7

Description of rigging work

3.7.1

Preparing the truck crane for rigging Do not override the RCL when lowering into a horizontal position.

If the following prerequisites are met, lowering into the horizontal position with lattice extension and a slewing range of 360° is permitted and is monSetting the RCL, p. 3 - 96. itored by the RCL;

à

Prerequisites for rigging

The following requirements must be met before the rigging of a lattice extension is started: – the lattice extension is mounted at the side on the main boom and is in transport condition.

– The counterweight version required according to the Lifting capacity table for the planned operation with the lattice extension is rigged.

– The truck crane is supported by the outrigger span required acc. to the Lifting capacity table for the planned operation with the lattice extension and is level.

– The main boom is completely retracted and has been lowered into horizontal position.

– All telescopic sections are completely retracted as far as possible.

– If the truck crane is equipped with two hoists as additional equipment, the hook block is unreeved on the hoist, which is not used for working with the lattice extension.

Prerequisites for unrigging

Before you lower the lattice extension into a horizontal position, the following requirements must be met: – No other load is raised apart from the hook block.

– The counterweight version required according to the Lifting capacity table for the planned operation with the lattice extension is rigged.

– The truck crane is supported with the outrigger span prescribed for operation with the rigged lattice extension according to the Lifting capacity table.

27.05.2014

s

Operating manual lattice extension GMK 3060i

3 113 112 en

3 - 31

8.7/15 m swing-away lattice extension 3.7 Description of rigging work

– All telescopic sections are completely retracted as far as possible.

– The RCL code for operation with the rigged lattice extension has been entered.

Securing lattice extension with cord

If the truck crane is not well aligned, the lattice extension may swing out of its own accord when you remove the last connection that held the lattice extension at the side of the main boom.

You must therefore secure the lattice extension before you begin with the rigging work.

G

Risk of accidents from lattice extension swinging of its own accord Always secure the lattice extension with a guide rope on the main boom before removing any connections.

This will prevent the lattice extension from slipping off the run-up rail, swinging around and knocking you off the carrier or injuring other persons in the slewing range.

Secure the lattice extension as follows:

• Attach a cord (2) at the front of the lattice extension.

• Guide the cord underneath the lattice extension, via the holding rod (1) on the main boom and back again.

• Have a helper hold the cord tight while you are removing the last connection.

27.05.2014

H

If you are alone, secure the other end of the cord on the crane (depending on the slewing direction of the superstructure, e.g. on the rear right on the outrigger beam or on the left on the steps of the access ladder to the carrier).

3 - 32

3 113 112 en

Operating manual lattice extension GMK 3060i

8.7/15 m swing-away lattice extension 3.7 Description of rigging work

3.7.2

Checking the transport condition For transportation you must establish certain connections between both sections of the lattice extension. The connections which need to be established depend on whether the lattice extension: – is folded up at the side of the main boom for transportation or – is completely removed for transportation.

Transport condition is when the lattice extension has been removed as described in the corresponding checklists.

S

Risk of damage to the lattice and the main boom Always put the lattice extension into transport condition before driving the truck crane with a lattice extension folded at the side or working with the main boom.

Only then is the lattice extension secured against slipping.

This way you prevent the partly fastened lattice extension hitting the main boom or the individual components of the lattice extension hitting each other and becoming damaged.

You have to check the transport condition: – After unrigging the lattice extension, before you drive the truck crane with the lattice extension folded at the side or work with the main boom.

– Before installation and before rigging the lattice extension.

The corresponding checklists require that the lattice extension is in transport condition.

The following paragraphs and the diagram show the necessary connections for the transport condition with the lattice extension folded at the side and removed.

27.05.2014

s

Operating manual lattice extension GMK 3060i

3 113 112 en

3 - 33

8.7/15 m swing-away lattice extension 3.7 Description of rigging work

The transport condition with the lattice extension folded at the side is created when all of the following connections are established.

27.05.2014

Transport condition with lattice extension folded at the side

3 - 34

3 113 112 en

Operating manual lattice extension GMK 3060i

8.7/15 m swing-away lattice extension 3.7 Description of rigging work

• Check the connections and establish them if necessary.

When section 1 and section 2 are folded to the side: – In the Front 1 area, the pin is inserted in the connecting point (4), between section 1 and the main boom; Establishing a connection, p. 3 - 46.

à

– In the Front 2 area, the pin is inserted in the connecting point (9), between section 1 and section 2 or in the connecting point (10), between section 2 Connection between section 2 and the main boom, and the main boom; p. 3 - 48.

à

– In the Middle area, the pin is inserted in the connecting point (3), between section 1 and the run-up rail; Connection run-up rail/section 1, p. 3 - 49.

à

– In the rear area, the pins are fit in the connecting points (1), between section 1 and section 2; Establishing a connection, p. 3 - 51.

à

– In the rear area, the unneeded pins (2) are secured in the holder.

– At the rear of section 1, the pins (8) are secured on both sides and if the slewing connection was disconnected, the swivel pins (7) will be secured.

– When using the hydraulically derricked lattice extension, the connections Breaking hang in the holder (5) and the hydraulic hoses (6) are fixed; the hydraulic connection, p. 3 - 42.

à

27.05.2014

s

Operating manual lattice extension GMK 3060i

3 113 112 en

3 - 35

8.7/15 m swing-away lattice extension 3.7 Description of rigging work

Only when section 1 is folded to the side: – In the Front 1 area, the pin is inserted in the connecting point (2), between Establishing a connection, p. 3 - 46. section 1 and the main boom;

à

– In the Middle area, the pin is inserted in the connecting point (1), between section 1 and the run-up rail; Connection run-up rail/section 1, p. 3 - 49.

à

– At the rear of section 1, the pins (5) are secured on both sides and if the slewing connection was disconnected, the swivel pins (6) will be secured.

– When using the hydraulically derricked lattice extension, the connections Breaking hang in the holder (3) and the hydraulic hoses (4) are fixed; the hydraulic connection, p. 3 - 42.

27.05.2014

à

3 - 36

3 113 112 en

Operating manual lattice extension GMK 3060i

8.7/15 m swing-away lattice extension 3.7 Description of rigging work

Only when section 2 is folded to the side: – In the Front 1 area, the pin is fitted in the connecting point (4) between Connection between section 2 and the main section 2 and the main boom; boom, p. 3 - 48.

à

– In the Middle area, the pin is fitted in the connecting point (2) between section 2 and the run-up rail; Connection run-up rail/section 2, p. 3 - 50.

à

– In the rear area, the pins (1) are secured in the holder.

– When using the hydraulically derricked lattice extension, the connections Breaking the hydraulic connection, p. 3 - 42. hang in the holder (3);

à

27.05.2014

s

Operating manual lattice extension GMK 3060i

3 113 112 en

3 - 37

8.7/15 m swing-away lattice extension 3.7 Description of rigging work

Transport condition with removed lattice extension

The transport condition for the removed lattice extension is established when all of the following connections have been made.

• Check the following connections and establish them if necessary.

– In the rear area, the pins (1) are fitted in the connecting points between section 1 and section 2; Establishing a connection, p. 3 - 51.

The unneeded pins (2) are secured in the holder.

à

– In the Front 2 area, the pin (4) is inserted in the connecting point (3) between section 1 and section 2; p. 3 - 47.

à

– At the rear of section 1, the swivel pins (5) are secured and the pins (6) will be secured on both sides.

– When using manually inclinable lattice extension, the pin (7) is inserted Setting the angle – with the auxiliary crane, in the 0° angle position; p. 3 - 86.

27.05.2014

à

3 - 38

3 113 112 en

Operating manual lattice extension GMK 3060i

8.7/15 m swing-away lattice extension 3.7 Description of rigging work

3.7.3

Checking the anti-twist device on the hose drum

H

S

All information in this section only applies to the hydraulically derricking lattice extension.

The hydraulic supply is provided through a hose drum on the right-hand side of the main boom. The hosedrum is equipped with an anti-twist device.

The anti-twist device is only needed for installing and removing the hosedrum.

Risk of damage to hydraulic hoses Always check if the anti-twist device is active before beginning operation with the lattice extension.

By doing this you prevent the hydraulic hoses tearing when the main boom is telescoped.

The anti-twist device must be active to operate with the lattice extension.

• Check if the spring latch (3) is inserted in one of the bores (1). In this case, you must unlock the anti-twist device.

Unlocking anti-twist device Withdraw spring latch (3) from the bore in the flanged wheel.

Inserting anti-twist device If the hose drum has to be removed, you have to insert the anti-twist device beforehand.

G

Risk of accidents from uncontrolled turning of hose drum The anti-twist device always has to be inserted before the hose drum is removed. Otherwise, the hose drum will twist uncontrollably against the holder and could injure you.

27.05.2014

s Operating manual lattice extension GMK 3060i

3 113 112 en

3 - 39

8.7/15 m swing-away lattice extension 3.7 Description of rigging work

• There are eight bores (1) distributed over a the radius on the inner flanged wheel (2) of the hose drum.

• Turn the hose drum until a bore is in front of the spring latch (3).

• Move the spring latch into the bore, the hose

27.05.2014

drum is secured against twisting.

3 - 40

3 113 112 en

Operating manual lattice extension GMK 3060i

8.7/15 m swing-away lattice extension 3.7 Description of rigging work

3.7.4

Establishing/disconnecting the hydraulic connection

H

G

All information in this section only applies to the hydraulically derricking lattice extension.

Danger of becoming trapped due to swinging lattice extension Start the subsequent work only if the lattice extension is locked in front of the main boom head or it is secured against swinging around.

This will prevent the lattice extension from swinging inadvertently on the side of the main boom and possibly crushing you.

You must detach the hydraulic connections when removing.

You must establish the hydraulic connections when installing.

Establishing the hydraulic connection

• Take the hydraulic hoses (3) off of the lattice extension and remove the protective caps.

• Take the connections (2) out of the holder (1) and remove the protective caps.

• Connect the hydraulic hoses (3) to the connections (2) (note colour marking!).

• Do not place the hydraulic hoses into the guide sheaves (4).

27.05.2014

s

Operating manual lattice extension GMK 3060i

3 113 112 en

3 - 41

8.7/15 m swing-away lattice extension 3.7 Description of rigging work

Breaking the hydraulic connection

S

Risk of damaging the lattice extension If the hydraulically derricked lattice extension is folded to the side on the main boom, the hydraulic connection must be separated. When the hydraulic connection is not separated, the foot section can lower itself down on its own. If the main boom is retracted, the head sheave axles knock against the foot section.

If the hydraulic connection is separated, the foot section cannot lower itself down on its own.

• Remove the hydraulic hoses (3) from the connections (2).

• Hang the connections (2) into the holder (1).

• Connect the connections (4) under the hydraulic hoses (3).

• Apply the protective caps to the hydraulic

27.05.2014

hoses (2) and the connections (4).

3 - 42

3 113 112 en

Operating manual lattice extension GMK 3060i

8.7/15 m swing-away lattice extension 3.7 Description of rigging work

3.7.5

Guides and holders for the hydraulic hoses

H When unrigging

G S

All information in this section only applies to the hydraulically derricking lattice extension.

There are two holders and guide sheaves for the hydraulic hoses.

The checklists for rigging and unrigging will tell you which type of rigging work is necessary at what time. There are different procedure for rigging and unrigging.

When unrigging, the lattice extension is folded between the work steps to the side of the main boom; CHECKLIST: Unrigging the 8.7/15 m swingaway lattice extension, p. 3 - 25.

à

Danger of becoming trapped due to swinging lattice extension Start the subsequent work only if the lattice extension is locked in front of the main boom head or it is secured against swinging around.

This will prevent the lattice extension from swinging inadvertently on the side of the main boom and possibly crushing you.

Risk of damage to hydraulic hoses Always remove the hydraulic hoses from the holder and from the guide sheaves before you swing the lattice extension to the side of the main boom.

In this way, you prevent the hydraulic hoses from kinking and being damaged when folding up the lattice extension.

Before folding

• Loosen the hinged pins (5) and fold up the guide sheaves (4).

• Remove the hydraulic hoses from the guide sheaves (6).

• Fold down the guide sheaves (4) and secure them with the hinged pins (5).

• Remove the connections (2) from the holder (1) and put the hydraulic hoses (3) over the guide sheaves.

27.05.2014

s

Operating manual lattice extension GMK 3060i

3 113 112 en

3 - 43

8.7/15 m swing-away lattice extension 3.7 Description of rigging work

After folding While the lattice extension is swinging as you fold it, the hose drum pulls the hydraulic hoses (3) to the rear.

• Insert the connections (2) into the holder (1).

When rigging

G

When rigging, you have to first swing and lock the lattice extension in front of the main boom head; CHECKLIST: Rigging the 8.7/15 m swing-away lattice extension, p. 3 - 19.

à

Danger of becoming trapped due to swinging lattice extension Start the subsequent work only if the lattice extension is locked in front of the main boom head or it is secured against swinging around.

This will prevent the lattice extension from swinging inadvertently on the side of the main boom and possibly crushing you.

• After swinging, the connections (2) will hang over the guide sheaves.

• Pull the hydraulic hoses (3) forwards and hang the connections (2) on the holder (1).

• Loosen the hinged pins (5) and fold up the guide sheaves (4).

• Put the hydraulic hoses onto the guide sheaves (6).

• Fold down the guide sheaves (4) and secure

27.05.2014

them with the hinged pins (5).

3 - 44

3 113 112 en

Operating manual lattice extension GMK 3060i

8.7/15 m swing-away lattice extension 3.7 Description of rigging work

3.7.6

Connections with folded lattice extension The lattice extension is swung to the side of the main boom in the folded up position.

In this position there are four areas on the main boom basic section, where various connections have to be disconnected and reconnected again during rigging and unrigging: 1 Front 1 area, in front of the driver's cab 2 Front 2 area, at the rear of the driver's cab 3 Middle area, above the storage box 4 Rear area, in front of the switch box In each area there are bearing points that can be used for establishing connections. Depending on the rigging mode and job, different sections of the lattice extension have to be connected one below the other or with the main boom basic section.

G Connections in the Front 1 area

Risk of accidents due to falling parts Always secure the pins both in the bearing points and in the holders using retaining pins.

This prevents unsecured pins from becoming loose, falling out and causing injuries.

In the Front 1 area, there is a connection between section 1 and the main boom.

This connection is established after the lattice extension was folded at the side of the main boom during unrigging or installation.

The connection can be disconnected after the slewing connection was established during rigging or removal.

27.05.2014

s

Operating manual lattice extension GMK 3060i

3 113 112 en

3 - 45

8.7/15 m swing-away lattice extension 3.7 Description of rigging work

Releasing the connection

G

Risk of accidents from a falling lattice extension p. 3 - 55), ensure that the slewing conBefore removing the connection ( nection is established at the front right-hand side on the main boom head.

This will prevent the lattice extension from falling as it is turned and causing injury to you or other persons.

à

• Secure the lattice extension with a guide rope;

à p. 3 - 32.

• Loosen the retaining pin and remove the pin (1) from the connecting point (2).

• Reinsert the pin (1) into the holder (3).

• Secure the pin with the retaining pin.

Establishing a connection

• Secure the lattice extension with a guide rope;

à p. 3 - 32.

• Release the retaining pin and remove the pin (1) from the holder (3).

• Insert the pin (1) into the connecting point (2).

27.05.2014

• Secure the pin with the retaining pin.

3 - 46

3 113 112 en

Operating manual lattice extension GMK 3060i

8.7/15 m swing-away lattice extension 3.7 Description of rigging work

Connections in the Front 2 area

In the Front 2 area, there is a pin that you can use to establish two different connections.

– The connection between section 2 and section 1, – The connection between section 2 and the main boom.

Connection between section 2 and section 1 This connection must be made: – when rigging the 15 m swing-away lattice extension – before the lattice extension is swung onto the main boom head, – before removing the complete swing-away lattice extension.

Establishing a connection

• Loosen the retaining pin and remove the pin (2) from the connecting point (3).

• Insert the pin (2) into the connecting point (1).

• Secure the pin with the retaining pin.

• Now the connection between section 1 and section 2 is established.

27.05.2014

s

Operating manual lattice extension GMK 3060i

3 113 112 en

3 - 47

8.7/15 m swing-away lattice extension 3.7 Description of rigging work

Connection between section 2 and the main boom This connection must be made: – when rigging the 8.7 m swing-away lattice extension – when section 2 is installed on the main boom.

– before removing – when only section 1 is supposed to be removed.

The connection must be disconnected when section 2 alone is installed on the main boom and is to be removed.

Establishing a connection

• Loosen the retaining pin and remove the pin (2) from the connecting point (1).

• Insert the pin (2) into the connecting point (3).

• Secure the pin with the retaining pin.

Now the connection between section 2 and and the main boom is established.

Releasing the connection

• Sling section 2 onto an auxiliary crane.

• Loosen the retaining pin and remove the pin (2) from the connecting point (3).

• Insert the pin (2) into the holder (1).

• Secure the pin with the retaining pin.

27.05.2014

• Lift section 2 from the main boom.

3 - 48

3 113 112 en

Operating manual lattice extension GMK 3060i

8.7/15 m swing-away lattice extension 3.7 Description of rigging work

Connections in the middle area

There is a pin in the Middle area. Using this pin, three different statuses can be established on the run-up rail.

– Connection run-up rail/section 1, – Connection run-up rail/section 2, – Connections released.

If the 15 m swing-away lattice extension is folded to the side, section 2 will also Securing/releasing section 2, p. 3 - 53. be secured to the run-up rail;

à

In the following sections, the term Connecting point will be used. A connecting point always consists of the holder (3) on the run-up rail and holders (1) on section 1 or section 2.

To create a connection, you must insert the pin (2) through the holders (1) and (3) and secure them with the retaining pin.

Connection run-up rail/section 1 This connection is made during unrigging, after the lattice extension is folded in to the side.

(A) – Before folding the lattice extension to the side:

• Remove the pin from connecting point (1) or (2).

(B) – If the lattice extension is already folded to the side:

• Fit the pin into the connecting point (2) and secure it.

Now the connection between section 1 and and the run-up rail is established.

27.05.2014

s

Operating manual lattice extension GMK 3060i

3 113 112 en

3 - 49

8.7/15 m swing-away lattice extension 3.7 Description of rigging work

Connection run-up rail/section 2 This connection is made when the 8.7 m swing-away lattice extension is rigged and section 2 is installed on the main boom.

(A) – Before folding the lattice extension to the side:

• Remove the pin from connecting point (1) or (2).

(B) – If the lattice extension is already folded to the side:

• Fit the pin into the connecting point (1) and secure it.

Now the connection between section 2 and and the run-up rail is established.

Releasing connections in the middle area The connection must be disconnected – before the 15 m swing-away lattice extension is swung in front of the main boom head during rigging, or – if section 2 alone is to be removed from the main boom.

• (A) – Remove the pin from the connecting point (1) or (2).

(B) – If the lattice extension is swivelled in front of the boom head:

• Fit the pin in connecting points (1) or (2) and secure it.

27.05.2014

Now all the connections between section 1 and section 2 are disconnected.

3 - 50

3 113 112 en

Operating manual lattice extension GMK 3060i

8.7/15 m swing-away lattice extension 3.7 Description of rigging work

Connections in the rear area

All information in this section only applies to the operation of the 8.7 mswing-away lattice extension, when section 2 is installed.

In the Rear area there is a connection between section 1 and section 2.

This connection is made after the 8.7 m swing-away lattice extension has been swung to the side of the main boom during unrigging.

This connection is released before the 8.7 m swing-away lattice extension is swung in front of the main boom during rigging.

Establishing a connection

• Pull the pins (1) out of the holder (3).

• Fit the pins into the connecting points (2) and secure them.

27.05.2014

s

Operating manual lattice extension GMK 3060i

3 113 112 en

3 - 51

8.7/15 m swing-away lattice extension 3.7 Description of rigging work

Releasing the connection

• Check if the connection between section 2 and the run-up rail is established in the Middle area;

à p. 3 - 50.

• Check if the connection between section 2 and the main boom established in the Front 2 area;

G

à p. 3 - 48.

Risk of accidents through section falling 2 Before releasing this connection, always check that section 2 is pinned in the Middle area and in the Front 2 area.

This will prevent section 2 from falling down when the connection is released.

• Pull the pins (1) out of the connecting points (2).

• Fit the pins into the holder (3) and secure

27.05.2014

them.

3 - 52

3 113 112 en

Operating manual lattice extension GMK 3060i

8.7/15 m swing-away lattice extension 3.7 Description of rigging work

3.7.7

Securing/releasing section 2 When section 2 is installed, it remains pinned to the main boom during operation of the 8.7 mswing-away lattice extension.

To prevent section 2 from slipping to one side and falling off when the main boom is derricked, it must be secured at the top on the run-up rail in addition to the pin connections in the Middle area.

The information in this section only applies to the manually inclinable and derricked lattice extension.

This lattice extension has a holder (1) in the middle area of the run-up rail to which you can secure section 2.

In order to use the 8.7 m swing-away lattice extension, you must secure section 2.

In order to use the 15 m swing-away lattice extension, you must release section 2.

G

Risk of accidents from a falling lattice extension Always secure section 2 before operating the 8.7 m swing-away lattice extension. In this way, you prevent section 2 from tilting off the run-up rail during operation, which could result in personal injury and damage to the main boom, add-on parts or section 2.

(A) – Securing section 2

• Pull the pin out of the connecting point (2).

• Fit the pin into the connecting point (1) and secure it.

(B) – Releasing section 2

• Pull the pin out of the connecting point (1).

• Fit the pin into the connecting point (2) and secure it.

27.05.2014

,

Operating manual lattice extension GMK 3060i

3 113 112 en

3 - 53

8.7/15 m swing-away lattice extension 3.7 Description of rigging work

27.05.2014

Blank page

3 - 54

3 113 112 en

Operating manual lattice extension GMK 3060i

8.7/15 m swing-away lattice extension 3.7 Description of rigging work

3.7.8

Connecting/disconnecting the slewing connection The slewing connection is made on the right of the main boom head using two pins. The pins required can be found in the holders at the rear of section 1.

G Creating a slewing connection

Risk of accidents due to falling parts Always secure the pins both in the connecting points and in the holders using retaining pins. This prevents unsecured pins from becoming loose, falling out and causing injuries.

The slewing connection must be established before the lattice extension has been swivelled in front of the main boom head during rigging.

The connecting points for the slewing connection will only align when the main boom is completely retracted.

• Remove the retaining pins and pull the pins (2) out of the holders (1).

• Insert the pins into the connecting points (3).

• Secure the pins using the retaining pins.

27.05.2014

s

Operating manual lattice extension GMK 3060i

3 113 112 en

3 - 55

8.7/15 m swing-away lattice extension 3.7 Description of rigging work

Releasing a slewing connection

G G

The connection must be released after the lattice extension is swivelled onto the main boom side and pinned there during unrigging.

Risk of accidents from a falling lattice extension When the lattice extension is folded to the side, make sure that all the connections are made as stipulated in the checklist Unrigging the 8.7 m/15 m swing-away lattice extension for the lattice extension currently installed; p. 3 - 25, point 22. to point 25.

In this way you prevent the lattice extension from slipping or falling from the boom when it is operated again after the connection is released and causing injury to you or other persons.

à

Danger of crushing by swinging lattice extension When removing, always secure the lattice extension with a guide rope before releasing the slewing connection, and only insert the pins in the holders when the lattice extension has been set down.

In this way you prevent the swinging lattice extension from knocking you off the ladder, or crushing you against the main boom.

• Remove the retaining pins and pull the pins (2) out of the connecting points (3).

• Insert the pins into the holders (1).

27.05.2014

• Secure the pins using the retaining pins.

3 - 56

3 113 112 en

Operating manual lattice extension GMK 3060i

8.7/15 m swing-away lattice extension 3.7 Description of rigging work

3.7.9

Connections on the left and right of the main boom head The connections to the right and left on the main boom head are made using pins. The pins required can be found in the holders at the rear left and right of section 1.

G Establishing connections

H

Risk of accidents due to falling parts Always secure the pins both in the connecting points and in the holders using retaining pins. This prevents unsecured pins from becoming loose, falling out and causing injuries.

The connections must be established after the lattice extension has been swivelled in front of the main boom head during rigging.

If the pins cannot be inserted, you can take the strain off the connecting points; Relieving the connecting points, p. 3 - 60.

à

Left-hand connection

• Swing the lattice extension in front of the main boom until the connecting points (3) align.

• Remove the retaining pins and pull the pins (2) out of the holders (1).

• Insert the pins into the connecting points (3).

• Secure the pins using the retaining pins.

27.05.2014

s

Operating manual lattice extension GMK 3060i

3 113 112 en

3 - 57

8.7/15 m swing-away lattice extension 3.7 Description of rigging work

Right-hand connections

• Remove the retaining pins and pull the pins (2) out of the holders (1).

• Insert the pins into the connecting points (3).

• Secure the pins using the retaining pins.

Releasing connections

The connections must be released so that the lattice extension can be swung to the side of the main boom during unrigging.

Right-hand connection Only release this connection when the connection on the left-hand side is still intact.

Risk of accidents from a falling lattice extension On this side, only release the two inner pins. The outerpins for the slewing connection must remain inserted.

If you release the slewing connection, the lattice extension will fall down when the pins on the left-hand side are released and could injure yourself or other people.

27.05.2014

G G

Danger of crushing if procedure is not followed Release the right-hand connection first, and then the right-hand connection.

In this way you prevent the lattice extension from swinging round when you release the right-hand connection, which could knock you from the ladder or lead to you becoming crushed between the lattice extension and the main boom.

3 - 58

3 113 112 en

Operating manual lattice extension GMK 3060i

8.7/15 m swing-away lattice extension 3.7 Description of rigging work

Right-hand connections The pins (4) for the slewing connection must remain inserted!

• Remove the retaining pins and pull the pins (2) out of the connecting points (3).

• Insert the pins into the holders (1).

• Secure the pins using the retaining pins.

Left-hand connection

H

Only release the left-hand connection after the right-hand connection has been released. The left-hand connection stops the lattice extension from swinging round when the right-hand connection is released.

• Remove the retaining pins and pull the pins (2) out of the connecting points (3).

• Insert the pins into the holders (1).

• Secure the pins using the retaining pins.

27.05.2014

s

Operating manual lattice extension GMK 3060i

3 113 112 en

3 - 59

8.7/15 m swing-away lattice extension 3.7 Description of rigging work

Relieving the connecting points

The dead weight of the lattice extension can cause misalignment of the bearing points, and can also weight down the pins and make it impossible to knock them out.

Proceed in the following manner to relieve the strain on the connecting points: For hydraulically derricking lattice extensions

• Lower the lattice extension until it is on the ground with the supports (2) (if necessary, override the lifting limit switch).

• Continue to lower carefully until the connecting points (1) align or until the load has Derricking been removed from the pins; the lattice extension, p. 3 - 83.

à

For manually inclinable lattice extensions

• Sling section 1 onto an auxiliary crane.

• Carefully raise the lattice extension until the

27.05.2014

connecting points (1) align or until the load has been removed from the pins.

3 - 60

3 113 112 en

Operating manual lattice extension GMK 3060i

8.7/15 m swing-away lattice extension 3.7 Description of rigging work

3.7.10

Swivelling the lattice extension when rigging

When rigging – section 1

When rigging the 8.7 m or 15 m swing-away lattice extension, you must swing section 1 in front of the main boom head.

• Check that the following conditions are met: – The slewing connection is established;

à p. 3 - 55.

– The lattice extension is secured with a guide rope at the front of p. 3 - 32. section 1;

à

– The connections which must be released before swivelling according to the checklist Rigging the 8.7 m/15 m swing-away lattice extension for the lattice extension currently installed have been released; p. 3 - 20, point 7. to point 10.

à

G

Risk of accidents from lattice extension swinging of its own accord Always secure the lattice extension with a guide rope before swivelling it.

Make sure that there are no people or objects in the slewing range of the lattice extension and always swivel the lattice extension from the ground using a guide rope.

For hydraulically derricking lattice extensions

• Carefully raise the lattice extension completely using the hand control

à

from the ground; p. 3 - 83.

The lattice extension will begin to swivel.

If a helper is holding the guide rope, he can now swing the lattice extension in front of the main boom head.

If you are alone and have attached the guide rope to the crane when securing, the lattice extension now swings only until the guide rope is tight. You can now swing the lattice extension in front of the main boom head using with the guide rope.

H

You may need to trigger the swivelling procedure by pulling on the guide rope.

27.05.2014

s

Operating manual lattice extension GMK 3060i

3 113 112 en

3 - 61

8.7/15 m swing-away lattice extension 3.7 Description of rigging work

For manually inclinable lattice extensions

• When rigging the 15 m swing-away lattice extension, release section 2;

à p. 3 - 53.

• From the ground, pull the lattice extension from the run-up rail using the guide rope, and swing it in front of the main boom head.

When unrigging – section 1

When unrigging the 8.7 m or 5 m swing-away lattice extension, you must swing section 1 to the side of the main boom.

G

Risk of accidents from lattice extension swinging of its own accord Always secure the lattice extension with a guide rope before swivelling it.

Make sure that there are no people or objects in the slewing range of the lattice extension and always swivel the lattice extension from the ground using a guide rope.

• Fasten a guide rope at the front of section 1 and lay the guide rope over the clamp (1) at the rear of the main boom.

• Swing the lattice extension to the side of the main boom.

• Pull the lattice extension onto the run-up rail.

• Secure the lattice extension with the guide rope.

27.05.2014

Get a helper to hold the guide rope taut, or fasten the other end of the guide rope to the crane (e.g. to the outrigger beam).

3 - 62

3 113 112 en

Operating manual lattice extension GMK 3060i

8.7/15 m swing-away lattice extension 3.7 Description of rigging work

For hydraulically derricking lattice extensions

• Derrick the lattice extension onto the run-up rail.

With the 15 m swing-away lattice extension, make sure that the Middle area of section 2 is secured in the holder (1) with a pin.

For manually inclinable lattice extensions

• Make the necessary connections with the lattice extension folded into the side; to do this, follow the checklist Unrigging the 8.7 m/15 m swing-away latp. 3 - 29. tice extension from point 23.;

à

When rigging – section 2

G

When rigging the 15 m swing-away lattice extension, you must swing section 2 in front of section 1 as well.

Risk of accidents through section 2 falling Always secure section 2 with a guide rope before you release the connection between section 1 and section 2 and only position the ladder on the left at section 1.

In this way you prevent part 2 from swinging round of its own accord when the connection is released and knocking you off the ladder.

• Fasten a guide rope to the front at section 2.

• Secure section 2 against swinging round.

Get a helper to hold the guide rope taut, or fasten it to the bottom of section 1.

27.05.2014

s

Operating manual lattice extension GMK 3060i

3 113 112 en

3 - 63

8.7/15 m swing-away lattice extension 3.7 Description of rigging work

• Loosen the retaining pin and remove the pin (2) from the connecting point (1).

• Insert the pin into the holder (3) and secure it with the retaining pin.

G

Risk of accidents through section 2 swivelling Make sure that there are no people or objects in the slewing range of the lattice extension and always swivel the lattice extension from the ground using a guide rope.

• Swivel section 2 in front of section 1 using the guide rope.

• Secure section 2 against swinging round.

Get a helper to hold the guide rope taut.

• If you are working alone, secure section 2 from swinging round on the left-hand side at section 1 using a second guide rope (1).

• Establish the left-hand connection between section 2 and section 1;

à Establishing a connection, p. 3 - 68.

When unrigging – section 2

S

When unrigging the 15 m swing-away lattice extension, you must swing section 2 to the side of section 1.

Risk of damage to the electrical cable on section 2 Always break the electrical connection between section 1 and section 2 before you swivel section 2 towards section 1. In this way you prevent the cable from being severed during swivelling.

• Check that the electrical connection between section 1 and section 2 has been broken;

à p. 3 - 71.

• Secure section 2 against swinging round.

Get a helper to hold the guide rope taut. left-hand side at section 1 using a second guide rope (1).

• Loosen the connection on the left between section 2 and section 1;

à Releasing a connection, p. 3 - 68.

3 - 64

3 113 112 en

Operating manual lattice extension GMK 3060i

27.05.2014

• If you are working alone, secure section 2 from swinging round on the

8.7/15 m swing-away lattice extension 3.7 Description of rigging work

G

Risk of accidents through section 2 swivelling Make sure that there are no people or objects in the slewing range of the lattice extension and always swivel the lattice extension from the ground using a guide rope.

• Swivel section 2 to the side of section 1 using the guide rope.

G

Risk of accidents through section 2 falling Always secure section 2 with a guide rope before you establish the connection between section 1 and section 2 and only position the ladder on the left at section 1.

In this way you prevent part 2 from swinging round of its own accord and knocking you off the ladder.

• Secure section 2 against swinging round.

Get a helper to hold the guide rope taut, or fasten it to the bottom of section 1.

• Remove the retaining pin and pull the pin (2) out of the holder (3).

• Insert the pin into the connection point (1) and secure it with the retaining

27.05.2014

pin.

Operating manual lattice extension GMK 3060i

3 113 112 en

3 - 65

8.7/15 m swing-away lattice extension 3.7 Description of rigging work

3.7.11

Establishing/releasing connections on the lattice extension The procedure for establishing and releasing the connections between section 1 and section 2 depends on the transport condition of the sections.

– When section 1 and section 2 are folded up on the side for transportation, you only need to establish and release the connection on the left-hand side; Section 1 and section 2 installed, p. 3 - 67.

à

– If only section 1 is folded up on the side for transportation and section 2 is removed for transportation, you must establish and release the connecOnly section 1 installed, p. 3 - 68. tions on both sides;

à

27.05.2014

G

Risk of accidents due to falling parts Always secure the pins both in the connecting points and in the holders using retaining pins. This prevents unsecured pins from becoming loose, falling out and causing injuries.

3 - 66

3 113 112 en

Operating manual lattice extension GMK 3060i

8.7/15 m swing-away lattice extension 3.7 Description of rigging work

Section 1 and section 2 installed

G H

This section presupposes that section 1 and section 2 are folded up on the side of the main boom for transportation.

2

Risk of accidents through section 2 swivelling of its own accord Always secure section 2 with a guide rope and only position the ladder on the left of section 1. In this way you prevent part 2 from swinging round of its own accord and knocking you off the ladder.

If necessary you can relieve the strain on the connecting points in a similar Relieving manner by setting down section 2 on the ground or raising it; the connecting points, p. 3 - 60.

à

(A) – Making a connection The connection is established after section 2 is swivelled in front of section 1.

• Take the pins (1) out of the holder (3).

• Insert the pins (1) into the connecting points (2) and secure them with retaining pins.

(B) – Releasing a connection The connection is released before section 2 is folded onto the side of section 1.

• Remove the pins (1) from the connecting points (2).

• Insert the pins (1) into the holder (3) and secure them with retaining pins.

27.05.2014

s

Operating manual lattice extension GMK 3060i

3 113 112 en

3 - 67

8.7/15 m swing-away lattice extension 3.7 Description of rigging work

Only section 1 installed

G

This section presupposes that section 1 is folded up on the side of the main boom and section 2 is removed for transportation.

Danger of crushing by swinging section 2 Always secure section 2 with a guide rope from the ground before establishing or releasing the connection.

In this way you prevent the swinging lattice extension from knocking you off the ladder, or you being crushed between the sections of the lattice extension.

• Fasten a guide rope to section 2.

• Sling section 2 onto an auxiliary crane, centre of gravity; à p. 3 - 10.

Establishing a connection

• Position section 2 so that the connecting points (2) align.

• Take the pins (1) out of the holder.

• Fit the pins (1) on both sides into the connecting points (2) and secure them with retaining pins.

Releasing a connection

• Remove the pins (1) from the connecting points (2) on both sides.

• Insert the pins (1) into the holder (3) and se-

27.05.2014

cure them with retaining pins.

3 - 68

3 113 112 en

Operating manual lattice extension GMK 3060i

8.7/15 m swing-away lattice extension 3.7 Description of rigging work

3.7.12

Electrical connections on the lattice extension The RCL, the lifting limit switch and the anemometer are connected via the electrical connection on the lattice extension.

G On 8.7 m swingaway lattice extension

Danger of becoming trapped due to swinging lattice extension Start the subsequent work only if the lattice extension is locked in front of the main boom head or it is secured against swinging around.

This will prevent the lattice extension from swinging inadvertently on the side of the main boom and possibly crushing you.

For the 8.7 m swing-away lattice extension the electrical connection is made or disconnected on the right side of the main boom head.

Establishing the electrical connection

• Remove the bridging plug (3) from the socket (1) and plug it into the dummy socket (2).

• Unwind the cable (5) from the holder (7).

• Remove the bridging plug (4) from the dummy socket (6) and plug it into the socket (1).

• Wind up the cable (5) far enough on the clamp (7) so that it does nor hang down.

27.05.2014

s

Operating manual lattice extension GMK 3060i

3 113 112 en

3 - 69

8.7/15 m swing-away lattice extension 3.7 Description of rigging work

• Check whether the bridging plug (2) is inserted in the socket (1) at the front on section 1.

Separating the electrical connection

• Remove the plug (4) from the socket (1) and plug it into the dummy socket (6).

• Wind the cable (5) onto the clamp (7).

• Remove the bridging plug (3) from the

27.05.2014

dummy socket (2) and plug it into the socket (1).

3 - 70

3 113 112 en

Operating manual lattice extension GMK 3060i

8.7/15 m swing-away lattice extension 3.7 Description of rigging work

On the 15 m swing-away lattice extension

• First make the electrical connection for the 8.7 m swing-away lattice extension;

à p. 3 - 69.

Establishing an electrical connection

• Remove the bridging plug (5) from the socket (1) and plug it into the dummy socket (4).

• Unwind the cable (3) from the clamp (6).

• Remove the plug (2) from the dummy socket (4) and plug it into the socket (1).

• Wind up the cable (3) far enough on the clamp (6) so that it does not sag.

S

Risk of damage to the cable Always disconnect the electrical connection before you swivel section 2 onto section 1. In this way, you prevent the cable from being severed during swivelling.

Separating an electrical connection

• Remove the plug (2) from the socket (1) and plug it into the dummy socket (4).

• Wind the cable (3) onto the clamp (6).

• Remove the bridging plug (5) from the dum-

27.05.2014

my socket (4) and plug it into the socket (1).

Operating manual lattice extension GMK 3060i

3 113 112 en

3 - 71

8.7/15 m swing-away lattice extension 3.7 Description of rigging work

3.7.13

Unfolding/folding the deflection sheave To prevent the hoist rope dragging on the main boom or lattice extension during operation with the lattice extension, the hoist rope is guided via deflection sheaves.

The deflection sheave on the rear of section 1 is hinged.

Folding out the deflection sheave

G G

For operation with the lattice extension you must fold put the deflection sheave.

Risk of accidents from exceeding the overall height permitted Always fold in the deflection sheave when the lattice extension is folded onto the side of the main boom for driving. When the deflection sheave is folded out, the overall height specified for on-road driving is exceeded.

Risk of crushing.

Always hold the deflection sheave by the handle when removing the pin.

You might get your fingers crushed if you hold the sheave by the side plate.

• (A) – Unscrew the retaining pin from the pin (2).

• Hold the deflection sheave by the handle (1) and pull out the pin (2).

• (B) – Fold the deflection sheave (3) upwards and fasten it in this position with the pin (2).

27.05.2014

• Secure the pin (2) using the retaining pin.

3 - 72

3 113 112 en

Operating manual lattice extension GMK 3060i

8.7/15 m swing-away lattice extension 3.7 Description of rigging work

Folding in the deflection sheave

G

You must fold in the deflection sheave before transporting the swing-away lattice extension.

Risk of crushing.

Always hold the deflection sheave by the handle when removing the pin.

You might get your fingers crushed if you hold the sheave by the side plate.

• (A) – Unscrew the retaining pin from the pin (2).

• Hold the deflection sheave by the handle (1) and pull out the pin (2).

• (B) – Fold the deflection sheave (3) downwards and fasten it in this position with the pin (2).

27.05.2014

• Secure the pin (2) using the retaining pin.

Operating manual lattice extension GMK 3060i

3 113 112 en

3 - 73

8.7/15 m swing-away lattice extension 3.7 Description of rigging work

3.7.14

G

Positioning hoist rope

Positioning/removing the hoist rope Risk of accidents due to falling parts Always secure the hoist rope holding rollers and rods with retaining pins.

This prevents elements from coming loose, falling down and injuring people.

• Remove the hoist rope holding rollers (1).

• Guide the hoist rope over the deflection sheaves (4), (3) and over the head sheave (2) to section 1 or section 2.

• Put all hoist rope holding rollers (1) back in place and secure them with retaining pins.

• Install the hook tackle or the hook block. The hoist rope may now be reeved once or twice, depending on the length of lattice extension; p. 3 - 75.

à Removing the hoist rope

• Unreeve the hook block.

• Remove the hoist rope holding rollers (1).

• Take the hoist rope off the head sheave (2) and the deflection sheaves (4), (3) and place it onto the ground on the left side.

• Put all hoist rope holding rollers back in place and secure them with re-

3 - 74

27.05.2014

taining pins.

3 113 112 en

Operating manual lattice extension GMK 3060i

8.7/15 m swing-away lattice extension 3.7 Description of rigging work

Possible reeving methods on the lattice extension

The hoist rope can be reeved a maximum of two falls on the 8.7 m swingaway lattice extension.

The hoist rope can be reeved only one fall on the 15 m swing-away lattice extension.

1-sheave hook block Maximum lifting capacity of the hook block Maximum lifting capacity with the GMK 3060i:

16 t

A For reeving 1-fall

5t

B For reeving 2-fall

8t

Hook tackle Maximum lifting capacity of the hook tackle Maximum lifting capacity with the GMK 3060i: A For reeving 1-fall

5t

5t

• With a 2-fall reeving, fasten the rope end clamp to the attachment plate (1)

27.05.2014

at the front on section 1.

Operating manual lattice extension GMK 3060i

3 113 112 en

3 - 75

8.7/15 m swing-away lattice extension 3.7 Description of rigging work

3.7.15

Installing/removing the lifting limit switch The functions Raise hoist, Extend main boom, Lower main boom and, with hydraulically derricking lattice extension, Derrick lattice extension are monitored during operation with the lattice extension by the lifting limit switch on the lattice extension and are switched off when the lifting limit switch is actuated.

H Overriding connection on main boom

The same lifting limit switch can be used for the lattice extension and the main boom. If two lifting limit switches are supplied as additional equipment, one lifting limit switch can stay connected to the main boom. This lifting limit switch must then be disabled, however.

For operation with the lattice extension you must remove the lifting limit switch from the main boom and then bridge the connection.

• Remove the bridging plug (3) from the dummy socket (2) and plug it into the socket (1).

The connections are now bridged.

à

27.05.2014

H

If a lifting limit switch remains connected to the main boom head, you must disable this lifting limit switch; Operating instructions GMK 3060i – Lifting limit switch.

3 - 76

3 113 112 en

Operating manual lattice extension GMK 3060i

8.7/15 m swing-away lattice extension 3.7 Description of rigging work

On 8.7 m swingaway lattice extension Connecting the lifting limit switch

• Fit the lifting limit switch (6) onto the clamp (4) and secure it with a retaining pin.

• Remove the bridging plug (3) from the socket (1) and plug it into the dummy socket (2).

• Lay the connecting cable (6) in such a way that it will not be damaged during crane operation, and connect the lifting limit switch to the socket (1).

Removing the lifting limit switch

• Pull the plug from the socket (1).

• Remove the bridging plug (3) from the dummy socket (2) and plug it into the socket (1).

• Remove the lifting limit switch (6) from the clamp (4).

• Attach the retaining pin to the lifting limit switch.

27.05.2014

s

Operating manual lattice extension GMK 3060i

3 113 112 en

3 - 77

8.7/15 m swing-away lattice extension 3.7 Description of rigging work

On 15 m swingaway lattice extension Connecting the lifting limit switch

• Fit the lifting limit switch (3) onto the clamp (2) and secure it with a retaining pin.

• Lay the connecting cable (4) in such a way that it will not be damaged during crane operation, and connect the lifting limit switch to the socket (1).

For operation with the 15 m swing-away lattice, the connection for the lifting limit switch must be overridden at the 8.7 m swing-away lattice with the short-circuit plug.

Removing the lifting limit switch

• Pull the plug from the socket (1).

• Remove the lifting limit switch (3) from the clamp (2).

• Attach the retaining pin to the lifting limit

27.05.2014

switch.

3 - 78

3 113 112 en

Operating manual lattice extension GMK 3060i

8.7/15 m swing-away lattice extension 3.7 Description of rigging work

3.7.16

Installing/removing the anemometer

On 8.7 m swingaway lattice extension

The same anemometer is used for the lattice extension and the main boom.

Mounting the anemometer

• Insert the rod (1) into the clamp (3) and secure it with the retaining pins.

• Remove the cable of the anemometer from the clamps (2) and connect it to the socket (4).

• Lay the cable so that it will not be damaged during crane operation.

• Check that the anemometer is able to swing so that is hangs vertically even when the main boom is raised.

You must remove the anemometer before driving on the road.

S

Risk of damage to the anemometer Remove the anemometer for on-road driving.

This prevents the anemometer from being damaged by wind (e.g. by suction currents caused by oncoming traffic in tunnels).

Removing the anemometer

• Take the plug out of the socket (4) and close the socket with the protective cap.

• Wind the cable onto the clamps (2).

• Take the rod (1) out of the clamp (3).

• For transportation, fasten the retaining pins to the rod (1).

27.05.2014

s

Operating manual lattice extension GMK 3060i

3 113 112 en

3 - 79

8.7/15 m swing-away lattice extension 3.7 Description of rigging work

On 15 mswingaway lattice extension

The same anemometer is used for the lattice extension and the main boom.

Mounting the anemometer

• Remove the retaining pin (2) and put the anemometer (1) on the holder (3).

• Secure the anemometer with the retaining pin (2).

• Swing out the anemometer and let go of it.

It must return to a vertical position after being swung out. The anemometer must also be suspended in a vertical position when the boom is raised.

• Remove the protective cap (5) and insert the plug (6) of the anemometer into the socket (4).

S

Risk of damage to the anemometer Remove the anemometer for on-road driving.

This prevents the anemometer from being damaged by wind (e.g. by suction currents caused by oncoming traffic in tunnels).

Removing the anemometer

• Pull the plug of the anemometer from the socket (4) and close the socket with the protective cap (5).

• Loosen the retaining pin (2).

• Remove the anemometer (1) from the holder (3).

• Fasten the retaining pin (2) to the anemome-

27.05.2014

ter (1).

3 - 80

3 113 112 en

Operating manual lattice extension GMK 3060i

8.7/15 m swing-away lattice extension 3.7 Description of rigging work

3.7.17

Installing/removing the air traffic control light

Installing

G

Danger of accidents due to the air traffic control light being on.

Always turn off the air traffic control light before you connect to the electrical power source.

In this way you will avoid your eyes being blinded temporarily or permanently by the bright light flashes from the switched on air traffic control light.

• Switch off the air traffic control light; press down the lower switch.

On 8,7 m swing-away lattice extension:

• Install the anemometer; à p. 3 - 79.

• Loosen the protective cap on the socket (1).

• Insert the plug of the air traffic control light into the socket (1).

On 15 m swing-away lattice extension:

• Install the anemometer; à p. 3 - 79.

• Loosen the protective cap on the socket (2).

• Insert the plug of the air traffic control light into the socket (2).

• Switch on the air traffic control light; press down the upper switch.

27.05.2014

s Operating manual lattice extension GMK 3060i

3 113 112 en

3 - 81

8.7/15 m swing-away lattice extension 3.7 Description of rigging work

Removing

• Switch off the air traffic control light; press down the lower switch.

On 8.7 m swing-away lattice extension:

• Remove the plug of the air traffic control light from the socket (1).

• Cover the socket (1) with the protective cap.

• Remove the anemometer; à p. 3 - 79.

On 15 m swing-away lattice extension:

• Remove the plug of the air traffic control light from the socket (2).

• Cover the socket (2) with the protective cap.

27.05.2014

• Remove the anemometer; à p. 3 - 79.

3 - 82

3 113 112 en

Operating manual lattice extension GMK 3060i

8.7/15 m swing-away lattice extension 3.7 Description of rigging work

3.7.18

Derricking the lattice extension

H

All information in this section only applies to the hydraulically derricking lattice extension.

• Before derricking the lattice extension, enter an RCL code for working with the lattice extension so that derricking will be enabled; p. 3 - 96.

When rigging

à Setting the RCL,

When rigging, you can control the derricking of the lattice extension using the button unit on section 1 or the hand-held control.

With the button unit on section 1 There is a button unit with two buttons on the front left side of section 1.

• To raise, press the frontmost push-button Raise lattice extension (1).

• To lower, press the rearmost push-button Lower lattice extension (2).

The lattice extension is lowered or raised as long as the corresponding push-button is pressed or until the end position or a switchoff point is reached.

With the hand-held control The socket (1) is at position (A) or (B) depending on the serial number.

• Connect the hand-held control to the socket (1).

Connection to the socket (2) is not suitable for rigging since you cannot see the folded lattice extension from this point.

27.05.2014

This socket is intended for emergency operation.

s Operating manual lattice extension GMK 3060i

3 113 112 en

3 - 83

8.7/15 m swing-away lattice extension 3.7 Description of rigging work

• Wait until the CAN (2) and Charge control (1) indicator lamps go on.

There is a malfunction if the CAN indicator lamp does not go on after approximately 20 seconds or if it flashes; Operating instructions GMK 3060i – Malfunctions – Hand-held control.

à

• Press the START (3) button and the diesel engine is started.

Release the button as soon as the diesel engine is running.

• Press in the preselection button Raise lattice extension (1) once.

The indicator lamp in the button lights up and you can derrick the lattice extension as described below using the buttons on the two-hand operating panel.

Raising

• Hold the direction button r and also press the Left/down movement button.

Lowering

• Hold the direction button r and also press the Right/up movement button.

27.05.2014

H

The lattice extension is lowered or raised as long as the buttons are pressed or until the end position or a switch-off point is reached.

3 - 84

3 113 112 en

Operating manual lattice extension GMK 3060i

8.7/15 m swing-away lattice extension 3.7 Description of rigging work

During operation

During operation the lattice extension is derricked from the crane cab.

The lattice extension can be derricked only when the derricking gear for the lattice extension is switched on.

After turning on the ignition, all power units are switched off and the indicator lamps in the corresponding rocker buttons light up dimly.

Switch on the derricking gear of the lattice extension

• Press button (1) once.

– The lamp in button (1) lights up brightly.

– The symbol (2) is green if the derricking gear of the lattice extension is switched on.

All other power units to which the same control lever movement is assigned are now switched off (e.g. derricking gear and telescoping mechanism).

Raising and lowering

H

Lowering:

Push the control lever to the right – the lattice extension is lowered.

Raising:

Push the control lever to the left - the lattice extension is raised.

The lattice extension is lowered or raised as long as the corresponding control lever is pushed in the corresponding direction or until the end position or a switch-off point is reached.

When the lattice extension is derricked, the RCL automatically switches to the values specified in the lifting capacity table for fixed lengths (0° inclination) and intermediate lengths (0-20° or 20-40° inclination) when this is permitted for the load currently being raised.

27.05.2014

If this switchover is not permitted for the load currently raised, derricking will be switched off and a corresponding error message will be generated.

Operating manual lattice extension GMK 3060i

3 113 112 en

3 - 85

8.7/15 m swing-away lattice extension 3.7 Description of rigging work

3.7.19

Setting the angle – with the auxiliary crane

H Setting the angle – with the auxiliary crane

The information in this section only applies to the manually inclinable lattice extension.

If an auxiliary crane is available, the lattice extension is slung to set the angle and the angle piece pin is put into the required position.

If no auxiliary crane is available;

à p. 3 - 88.

When rigging

• Lift the lattice extension with the auxiliary crane until the pin (1) is relieved.

• Put the angle piece pin into the position for the required angle;

à p. 3 - 87.

• Lower the lattice extension and remove the lifting gear.

If the lattice extension now touches the ground at the set angle, then the angle sets itself during the raising of the main boom.

When unrigging

• Lift the lattice extension to the horizontal position with an auxiliary crane.

• Position the pin (1) into the position for a 0° angle;

à p. 3 - 87.

• Remove the lifting gear from the lattice

27.05.2014

extension.

3 - 86

3 113 112 en

Operating manual lattice extension GMK 3060i

8.7/15 m swing-away lattice extension 3.7 Description of rigging work

Pin positions

G

The angle degree is determined by the position of the angle pin. There are three positions.t Risk of accidents from lattice extension folding down Always secure the lattice extension with an auxiliary crane before you knock out pins when setting the angle.

– Either use the auxiliary crane – or set down on the ground In this way you prevent the lattice extension suddenly unfolding and injuring yourself or other people.

0° angle (A) – For a 0° angle, the pin (1) is set in the front bore and is secured with the retaining pin.

20° angle (B) – For a 20° angle, the pin (1) is set in the back bore and is secured with the retaining pin.

27.05.2014

40° angle (C) – For a 40° angle, the pin (1) is set in the holder (2) and is secured with the retaining pin.

Operating manual lattice extension GMK 3060i

3 113 112 en

3 - 87

8.7/15 m swing-away lattice extension 3.7 Description of rigging work

3.7.20

Setting the angle – without the auxiliary crane If an auxiliary crane is not available, the lattice extension must be set down before it is angled.

S Entering the RCL code

Risk of damage to the hoist rope Unreeve the hook block and set down the hoist rope beside the lattice extension before you angle the lattice extension.

In this way you prevent the hoist rope from being damaged when the head of the lattice extension is set down on the ground for angling.

When angling without an auxiliary crane, you must enter an RCL rigging code. The RCL rigging code depends on: – the rigged outrigger span – the rigged counterweight – the working position

G G

Risk of overturning with impermissible rigging mode Always enter the RCL rigging code for the current rigging mode of the truck crane, and only slew the superstructure into the working position permitted by the RCL rigging code set according to the Lifting capacity table.

This prevents the truck crane from overturning when the main boom is extended.

Risk of overturning with raised hook block (hook tackle) The telescoping range which is enabled for the rigging code set is only permissible for telescoping without a load and without hook block/hook tackle.

When the main boom is fully extended, load measurement is not possible and the RCL monitoring depends on the working radius.

For this reason, you must unreeve the hook block. This prevents the truck crane from overturning when the main boom is extended.

• Enter the RCL rigging code for angling in accordance with the current rigging mode of the truck crane; à Lifting capacity tables - Chapter Rigging tables - Swing-away lattice extension.

• Slew the superstructure into a working position permitted by the Lifting

27.05.2014

capacity table for the RCL rigging code set.

3 - 88

3 113 112 en

Operating manual lattice extension GMK 3060i

8.7/15 m swing-away lattice extension 3.7 Description of rigging work

Setting an angle of 20° or 40°

G G

This section assumes that the lattice extension has been pinned in front of the main boom and the unreeved hoist rope has been set down beside the lattice extension.

Risk of accidents if this procedure is not followed!

For the procedure described here, the lattice extension must be set down on the ground. If the lattice extension is to be set down on some other structure for inclination, please bear in mind that the lattice extension will slide towards the truck crane when raised, until the angle of inclination is reached.

This means that the lattice extension could slip off an unsuitable structure, fold down and injure yourself or other people.

Risk of accidents when RCL is overridden Never override the RCL if the crane movements are switched off. In this way you prevent the superstructure from being slewed into impermissible areas and the truck crane tipping over as a result.

• Enter the RCL rigging code for the inclination;

à p. 3 - 88.

• Extend the main boom as far as is permitted for the RCL rigging code set, or as far as possible given the space available.

• Lower the main boom until the lattice extension head touches the ground.

• If the ground cannot be reached, you can incline the truck crane further;

H

à p. 3 - 93.

In the steps which follow, the lattice extension head is pulled or pushed over the ground. Lay boards or similar under the skids on the lattice extension head so that it is not pushed against the ground or damaged.

27.05.2014

s

Operating manual lattice extension GMK 3060i

3 113 112 en

3 - 89

8.7/15 m swing-away lattice extension 3.7 Description of rigging work

• If necessary, relieve the pin (1) by raising slightly.

• Position the pin (1) into the position for the angle required, e.g. 40°;

à p. 3 - 87.

• Raise the main boom slowly.

When doing so, the head of the lattice extension will be pulled across the ground.

• Lower the main boom until the lattice extension head is no longer touching the ground.

The lattice extension will then be inclined by the angle set, e.g. 40°.

If you inclined the truck crane using the outriggers in order to set the angle, align it to the horizontal again.

• Fully retract the main boom. While doing so, the lattice extension must not touch the ground (raise now and then if necessary).

• Set down the head of the lattice extension

27.05.2014

on the ground.

3 - 90

3 113 112 en

Operating manual lattice extension GMK 3060i

8.7/15 m swing-away lattice extension 3.7 Description of rigging work

• Slowly lower the main boom into a horizontal position.

When doing so, the head of the lattice extension will be pushed across the ground.

The lattice extension is now in the right position for attaching the hoist rope.

G Setting 0° angle

Risk of overturning when truck crane is standing at an angle.

After setting the angle, always check whether the truck crane is aligned to the horizontal.

In this way you prevent the actual working range differing from the permitted working range, leading to the truck crane tipping over.

The section assumes that no load has been raised and that the hook block has been unreeved.

• Set down the head of the lattice extension on the ground.

H

In the steps which follow, the lattice extension head is pulled or pushed over the ground. Lay boards or similar under the skids on the lattice extension head so that it is not pushed against the ground or damaged.

• Slowly lower the main boom into a horizontal position.

When doing so, the head of the lattice extension will be pushed across the ground.

• Remove the hoist rope (1) and set it down beside the lattice extension.

27.05.2014

s Operating manual lattice extension GMK 3060i

3 113 112 en

3 - 91

8.7/15 m swing-away lattice extension 3.7 Description of rigging work

• Slowly lower the main boom until the lattice extension head is no longer touching the ground.

• Enter the RCL rigging code for angling;

à p. 3 - 91.

• Extend the main boom as far as is permitted for the RCL rigging code set, or as far as possible given the space available.

• Lower the main boom until the lattice extension head touches the ground.

• If the ground cannot be reached, you can incline the truck crane further;

à p. 3 - 93.

• Slowly lower the main boom until the 0° angle is reached.

When doing so, the head of the lattice extension will be pushed across the ground.

• Put the pin (1) of the angle piece into the position for a 0° angle;

à p. 3 - 87.

• Derrick the main boom into the horizontal position and retract it completely.

27.05.2014

The lattice extension is now in the right position to continue rigging.

3 - 92

3 113 112 en

Operating manual lattice extension GMK 3060i

8.7/15 m swing-away lattice extension 3.7 Description of rigging work

H Inclining the truck crane

If you inclined the truck crane using the outriggers, align it to the horizontal now so that the lattice extension sections can be folded more easily.

In order to set the angle of the lattice extension, you must set it down on the ground by extending and lowering the main boom.

Depending on the space available, the condition of the terrain or a limitation on the telescoping due to the current rigging mode, it may be that the lattice extension cannot be set down on the ground by telescoping and lowering the main boom.

In this case, you can use the outriggers to incline the truck crane.

G

Risk of accidents if the wheels touch the ground Make sure that the wheels do not touch the ground when the truck crane has been inclined. In this way you prevent a reduction in the stability of the truck crane, which could lead to it tipping over when setting the angle of the lattice extension.

• Extend the outrigger cylinders on the counterweight side.

• Extend the outrigger cylinders on the main boom side. Be sure that the

27.05.2014

wheels do not touch the ground when doing this.

Operating manual lattice extension GMK 3060i

3 113 112 en

3 - 93

8.7/15 m swing-away lattice extension 3.7 Description of rigging work

3.7.21

G

Transportation on a separate vehicle Risk of accidents from a falling lattice extension Only attach the lattice extension in such a way that it is positioned in the centre of gravity and always use lifting gear with sufficient lifting capacity.

This prevents the lattice extension falling and injuring people while loading; Centres of gravity for slinging, p. 3 - 10, Transport dimensions and weights, p. 2 - 1.

à à

• Check if all the required connections for transport condition are established;

à Transport condition with removed lattice extension, p. 3 - 38.

• For transportation, place the lattice extension on the skid (1) at the front and onto the lower connecting points (2) at the rear.

• Always secure the lattice extension on the separate vehicle with belts as well to prevent slipping and overturning.

27.05.2014

S

Risk of damaging the lattice extension Always secure the lattice extension by tying it down with suitable belts when it is transported on a separate vehicle. This prevents the swing-away lattice extension tipping and becoming damaged during transportation.

3 - 94

3 113 112 en

Operating manual lattice extension GMK 3060i

8.7/15 m swing-away lattice extension 3.8 Operation with the lattice extension

3.8

Operation with the lattice extension

H

When operating the lattice extension, the speed for all power units is limited to 70%.

The hoisting, lowering, slewing, derricking and telescoping movements are done in the same way as when operating with the main boom. This section only contains information that you will need for a rigged or installed lattice extension:

à Setting the RCL, p. 3 - 96, à Derricking the main boom, p. 3 - 98, à Telescoping with rigged lattice extension, p. 3 - 99, à Information about the RCL shutdown, p. 3 - 100, à Procedure if permissible wind speed is exceeded, p. 3 - 101, à Information about the main boom operation when the lattice extension is folded/ rigged, p. 3 - 102,

27.05.2014

à Information about the RCL shutdown, p. 3 - 100.

Operating manual lattice extension GMK 3060i

3 113 112 en

3 - 95

8.7/15 m swing-away lattice extension 3.8 Operation with the lattice extension

3.8.1

Setting the RCL

H

If a hook block is reeved on the main boom during operation with the lattice extension, the loads given in the Lifting capacity tables decrease and the RCL subsequently switches off earlier.

The values which must be deducted from the load capacities depend on the length of the lattice extension and the weight of the hook block. You will find a table with the values in the Lifting capacity tables in the Section Remarks about working with the swing-away lattice extension.

There are different procedures when setting the RCL, depending on whether the hydraulically derricking lattice extension or the manually inclinable lattice extension is rigged.

Luffable lattice extension

The length of the lattice extension is also given and displayed on a hydraulically derricking lattice extension.

• Enter the current reeving at the RCL. • Enter the current rigging mode on the RCL, either using the corresponding RCL code according to the Lifting capacity table or using the individual components.

• Check whether the current rigging mode of the truck crane corresponds to the displayed rigging mode.

• Check: 1 the current angle of derricking lattice extension 2 the length of the rigged lattice extension

X.X° X.Xt

X.XXm

3 the hoist that is switched on

X.Xt

4 the number of reeved rope lines

X.X%

X.Xm

X.X°

5 the rigged outrigger span

X.Xm

X.XXt

6 the rigged counterweight

X.X° X.Xm

Xm

Xm

Xm

Xm

If the telescopic sections are mechanically locked, the RCL will release the load according to the Lifting capacity table and the Maximum load display (1) shows the corresponding value.

Otherwise, only the value for the empty-hook curve is released and displayed.

3 - 96

3 113 112 en

Operating manual lattice extension GMK 3060i

27.05.2014

– The display (7) shows the RCL code as per the Lifting capacity table.

8.7/15 m swing-away lattice extension 3.8 Operation with the lattice extension

Depending on the current angle, the RCL automatically switches to the capacity diagram for fixed lengths (0° inclination) and intermediate lengths (0-20° or 20-40° inclination) when this is permitted for the load currently being raised.

Inclinable lattice extension

For manually inclinable lattice extensions, the length and the set angle of the lattice extension are also entered and displayed.

• Enter the current reeving at the RCL. • Enter the current rigging mode on the RCL, either using the corresponding RCL code according to the Lifting capacity table or using the individual components.

• Check whether the current rigging mode of the truck crane corresponds to the displayed rigging mode.

• Check: 1 the angle set for the inclinable lattice extension (e.g. 20°)

X.X°

2 the length of the rigged lattice extension

X.Xt

X.XXm

X.Xt

3 the hoist that is switched on

X.X%

X.Xm

4 the number of reeved rope lines X.X°

X.Xm

5 the rigged outrigger span

X.XXt X.X° X.Xm

Xm

Xm

Xm

Xm

6 the rigged counterweight

– The display (7) shows the RCL code as per the Lifting capacity table.

If the telescopic sections are mechanically locked, the RCL will release the load according to the Lifting capacity table and the Maximum load display (1) shows the corresponding value.

27.05.2014

Otherwise, only the value for the empty-hook curve is released and displayed.

Operating manual lattice extension GMK 3060i

3 113 112 en

3 - 97

8.7/15 m swing-away lattice extension 3.8 Operation with the lattice extension

3.8.2

G

Derricking the main boom Risk of accidents if the RCL is overridden Do not override the RCL when lowering the boom into horizontal position.

If the RCL is overridden, the crane operation will not be monitored and the truck crane will overturn if it moves outside of the permissible working range.

If the following prerequisites are met, lowering into the horizontal position with swing-away lattice and a slewing range of 360° is permitted and is monitored by the RCL. – The current rigging mode with the rigged lattice extension is entered on the RCL, and the corresponding RCL code is displayed as per the Lifting capacity table.

– The current reeving type on the lattice extension is entered for the hoisting gear whose hoist rope is secured to the lattice extension.

– Apart from the hook block there is no load on the lattice extension.

– The main boom is fully retracted.

The RCL will only release the main boom for raising and setting it down when the main boom is completely retracted.

27.05.2014

When all of the above prerequisites have been satisfied, the RCL will automatically switch to the rigging tables and derricking is then also permitted within the angle range that is below the working range of approx. 75°.

3 - 98

3 113 112 en

Operating manual lattice extension GMK 3060i

8.7/15 m swing-away lattice extension 3.8 Operation with the lattice extension

3.8.3

S

Telescoping with rigged lattice extension Risk of overloading the main boom When you are telescoping the main boom with the lattice extension rigged, you may not simultaneously slew the superstructure.

This prevents the main boom being subjected to additional side forces and increased vibration and becoming overloaded.

The telescoping of the main boom with a rigged lattice extension is monitored by the RCL. The telescoping will only be released if the main boom is derricked to a certain angle and a maximum permissible load is not exceeded.

The required angle (between 70° and 83°) depends on: – the length of the swing-away lattice extension, – the inclination or angle of the swing-away lattice extension, – the extended length of the main boom, – the rigged counterweight, – the rigged outrigger span.

You will find the required main boom angle and the maximum permissible load (weight of the hook block) in the Lifting capacity tables, in Chapter Rigging tables – Lattice extension.

If the main boom angle is too small for telescoping with the rigged lattice extension, the RCL shows the corresponding error message.

27.05.2014

The telescoping mechanism is operated in the same way as the main boom; à Operating instructions GMK 3060i – Telescoping mechanism.

Operating manual lattice extension GMK 3060i

3 113 112 en

3 - 99

8.7/15 m swing-away lattice extension 3.8 Operation with the lattice extension

3.8.4

Information about the RCL shutdown The operation with the lattice extension is monitored by the RCL. RCL shutdowns can occur during lattice extension operation for the same Operating instructions GMK 3060i. reasons as with main boom operation;

à

When operating the hydraulically derricking lattice extension, there are two additional points to be considered: – When using the hydraulically derricking lattice extension, different lifting capacities are released for the angles 0°, 0 - 20° and 20 - 40°. Lowering the lattice extension can lead to the RCL shutting down, when the currently raised load in the recently set angle range is not permitted.

27.05.2014

– When the RCL has shut down, the lower lattice extension movement as well as all other movements which increase the load moment are blocked.

3 - 100

3 113 112 en

Operating manual lattice extension GMK 3060i

8.7/15 m swing-away lattice extension 3.8 Operation with the lattice extension

3.8.5

G

Procedure if permissible wind speed is exceeded Risk of accidents from excessively high wind speeds If the current wind speed is higher than the maximum permissible wind speed, cease crane operation immediately and set up the corresponding rigging mode.

This will prevent the truck crane from overturning due to overload.

• Prior to and during crane operation, check whether the current wind speed is lower than the maximum permissible wind speed.

• Make sure that you follow the instructions for checking the wind speed;

à Lifting capacity table and Operating instructions GMK 3060i.

If the maximum permissible wind speed is exceeded No automatic shutdown occurs if the maximum permissible wind speed is exceeded.

• Immediately cease crane operation.

• Put the truck crane into the rigging mode specified for the current wind

27.05.2014

speed in the Lifting capacity table.

Operating manual lattice extension GMK 3060i

3 113 112 en

3 - 101

8.7/15 m swing-away lattice extension 3.8 Operation with the lattice extension

3.8.6

Information about the main boom operation when the lattice extension is folded/rigged

Folded

This section applies when the lattice extension is folded at the side.

If a lattice extension is folded at the side during operation with the main boom, the loads given in the Lifting capacity tables decrease.

The relevant formulas and examples for calculating these values during operations planning can be found in the lifting capacity tables in the Section Remarks about working with the swing away lattice extension.

The decreased values are shown directly on the RCL insert in the Maximum load display (1).

Rigged

S

This section applies when the lattice extension is rigged and locked to the main boom head.

Risk of overturning when rigging mode is impermissible The main boom operation with a rigged lattice extension is only permissible in rigging modes that are also permissible for the rigged lattice extension (outrigger span, counterweight, slewing range).

When you set up rigging modes that are only valid for main boom operation without a rigged lattice extension (e.g. Free on wheels working position), then the truck crane could overturn during operation.

For operation with the main boom with a rigged lattice extension, you must enter the current rigging mode for the main boom without a lattice extension on the RCL.

27.05.2014

The values given in the corresponding Lifting capacity tables for the lifting capacities and for the permissible wind speeds decrease in this case.

3 - 102

3 113 112 en

Operating manual lattice extension GMK 3060i

8.7/15 m swing-away lattice extension 3.8 Operation with the lattice extension

Reduction of the lifting capacity The Maximum load display (1) does not show the reduced values.

The RCL also takes into account the load moment affected by the currently rigged extension and will correspondingly switch off earlier.

In the Lifting capacity tables you will find tables with values for the reduction of the lifting capacities in the Section Remarks about working with the swingaway lattice extension. The given values for reduction are only maximum values for certain rigging modes (angle and length of main boom and lattice extension).

However, the RCL takes into account the value for the currently rigged lattice extension, adds the weight of the raised load and displays the sum on the Current load display (1).

The displayed value could deviate from the value that was previously calculated during the operations planning.

If this is the case, the RCL is not defective. Do not override the RCL, even when the displayed value is higher than the calculated value.

G

Risk of accidents when RCL is overridden Never override the RCL. If the RCL is overridden, the crane operations will not be monitored and the truck crane will overturn if you leave the permissible working range.

Reduced values for the maximum wind speed There are also the maximum permissible wind speeds for this special rigging mode in the tables with values for the reduction of the lifting capacities.

• Stop operating the crane when the specified wind speeds have been reached.

à

27.05.2014

G

Risk of accidents due to high wind speeds Pay attention to the wind speeds that apply to this specific case in the Lifting capacity tables.

When the given wind speeds have been reached, you have to stop operatProcedure if permissible wind speed is exceeded, p. 3 - 101. ing the crane;

Operating manual lattice extension GMK 3060i

3 113 112 en

3 - 103

8.7/15 m swing-away lattice extension 3.8 Operation with the lattice extension

27.05.2014

Blank page

3 - 104

3 113 112 en

Operating manual lattice extension GMK 3060i

8.7/15 m swing-away lattice extension 3.9 Turning loads with the lattice extension

3.9

Turning loads with the lattice extension Two-hook operation is required to turn loads.

G Prerequisites

Risk of accidents due to incorrect procedure Before turning loads, observe all the prerequisites specified in this section and proceed exactly as described. This way, you avoid accidents due to overload.

– The main hoist rope is reeved on the main boom.

– The auxiliary hoist rope is reeved on the lattice extension.

– The main hoist rope is reeved with the same or a higher number of falls than the auxiliary hoist rope.

3.9.1

Setting the RCL

Switch on the auxiliary hoist and enter the reeving

Before lifting the load, the number of currently reeved falls of both the hoists must be entered at the RCL so that they can be immediately taken into account in case you switch between the hoists later after turning the loads.

The load must first be lifted using the auxiliary hoist. For this purpose, the RCL must first be switched over to the auxiliary hoist so that the relevant reeving is taken into account.

Proceed as follows:

• Switch off both hoists – Displays (1) and (2) are red.

• Switch the main hoist on – Display (1) is green.

27.05.2014

• Enter the number of falls (1) currently reeved on the main hoist.

s Operating manual lattice extension GMK 3060i

3 113 112 en

3 - 105

8.7/15 m swing-away lattice extension 3.9 Turning loads with the lattice extension

• Switch the auxiliary hoist on – Display (1) is green.

• Enter the number of falls currently reeved on the auxiliary hoist.

• Enter the RCL code that corresponds to the rigging mode as per the Lifting capacity table for the lattice extension; à Setting the RCL, p. 3 - 96.

The RCL now takes into account: – the reeving for the auxiliary hoist and – the Lifting capacity tables for the lattice extension.

27.05.2014

H

In two-hook operation, the loads given in the Lifting capacity table are reduced by the weight of both reeved hook blocks.

3 - 106

3 113 112 en

Operating manual lattice extension GMK 3060i

8.7/15 m swing-away lattice extension 3.9 Turning loads with the lattice extension

3.9.2

Turning a load

H

Before turning loads, check whether these procedures are in accordance with the regulations in the country in which you are working.

• Check whether all prerequisites have been met;

à Prerequisites, p. 3 - 105.

• Check whether the RCL is correctly set;

à Setting the RCL, p. 3 - 105.

G H

Risk of accidents due to overload Ensure that the RCL is set for operation with the lattice extension during the entire procedure and only move the load at minimum speed.

In this way you prevent the crane from becoming overloaded.

As soon as the load is on two hooks, there will be slight differences in the Current load display. However, these deviations are on the safe side with regard to RCL shutdown.

• Lift the load fully using the lattice extension.

• (B) – Sling the load additionally at the main

27.05.2014

boom.

Operating manual lattice extension GMK 3060i

3 113 112 en

3 - 107

8.7/15 m swing-away lattice extension 3.9 Turning loads with the lattice extension

• (A) – Lift the load with the main hoist until both slinging points are at the same height.

• (B) – Lower the load with the auxiliary hoist until the load is completely suspended from the main hoist rope.

• Enter the RCL code that corresponds to the rigging mode as per the Lifting capacity table for main booms.

• Switch over the RCL to the main hoist.

27.05.2014

Turning the load has now been completed.

3 - 108

3 113 112 en

Operating manual lattice extension GMK 3060i

8.7/15 m swing-away lattice extension 3.10 Driving with rigged crane with a rigged lattice extension

3.10

Driving with rigged crane with a rigged lattice extension This section describes how you can move the truck crane with an installed counterweight and rigged lattice extension (e.g. when the lattice extension cannot be rigged on the site due to lack of space).

Risk of accidents due to swinging hook block Secure the hook block against swinging when driving the equipped truck crane.

Risk of overturning when rotating the superstructure Before a rigged crane can be driven, the superstructure must be locked and the slewing gear brake must be engaged.

Risk of accidents due to partially obstructed view of the truck crane When moving the rigged truck crane, always keep in contact with a banksman, either by sight or by means of radio.

Risk of accidents when driving from the crane cab Before driving the truck crane from the crane cab, observe all instructions in the Operating instructions GMK 3060i and set the rigging mode described therein for free-standing work; Operating instructions GMK 3060i - Driving from the driver's cab or Driving from the crane cab.

à

27.05.2014

G G G G G

Risk of accidents when driving with a lifted load When using a rigged lattice extension, you must not move the truck crane with a load on the hook.

Put the load down before you move the truck crane.

Operating manual lattice extension GMK 3060i

3 113 112 en

3 - 109

8.7/15 m swing-away lattice extension 3.10 Driving with rigged crane with a rigged lattice extension

3.10.1

Driving route The route must be along a flat, even surface. The level adjustment system cannot compensate for uneven surfaces. If the surface pressure of the tyres exceeds the permissible load on the ground, the bearing surface pressure must be increased using packing made of durable material (e.g. wooden planks).

S 3.10.2

Risk of damage to tyres Check the pressure in the tyres before moving the rigged truck crane.

The truck crane may be moved only if tyre pressures are at the prescribed levels; Operating instructions GMK 3060i – Section 1 Driving – Technical data.

Do not reduce the tyre pressure.

à

Boom positions and axle loads The truck crane may only be moved under certain circumstances. The main boom and the lattice extension must be moved to specified positions, depending on the counterweight installed.

S

Risk of damage to the axle lines Always move the main boom and the lattice extension to the specified position before you move the rigged truck crane. Positions which deviate from the specified position cause impermissible loads on the axle lines.

• Enter RCL code according to the Lifting capacity table for the actual rigging mode of the truck crane with the rigged lattice extension.

• Move the main boom and the lattice extension into the prescribed posi-

27.05.2014

tions. The prescribed boom position can be found in the following tables.

3 - 110

3 113 112 en

Operating manual lattice extension GMK 3060i

8.7/15 m swing-away lattice extension 3.10 Driving with rigged crane with a rigged lattice extension

G Information about the tables

Risk of accidents when RCL is overridden Always set the RCL code corresponding to the current rigging mode when you derrick the main boom or lattice extension into the prescribed position.

Do not override the RCL; the prescribed positions in the following tables are all within the areas which are permitted according to the Lifting capacity tables.

The truck crane operates without overload protection when the RCL is overridden!

The axle loads specified in the tables relate to – a driving mode with the basic unit and – to the specified, maximally reeved hook block or hook tackle. Larger hook blocks must be unreeved.

In the case of different tyres, the axle load changes by double the weight difSpare wheel in the section titled Technical data in the ference of a wheel; Operating instructions GMK 3060i.

à

The following applies to the footnotes in the tables: 1)

2)

Rear:

Display, slewing angle 0°

Front:

Display, slewing angle 180°

Front:

On the 1st axle line each

Rear:

On the 2nd and 3rd axle line each

27.05.2014

s

Operating manual lattice extension GMK 3060i

3 113 112 en

3 - 111

8.7/15 m swing-away lattice extension 3.10 Driving with rigged crane with a rigged lattice extension

8.7 m swing-away lattice extension

H Counterweight in t

All the axle loads in the following table apply for a 16 t hook block (weight 210 kg) reeved on the lattice extension.

The maximum axle load specified in the table is reached at a main boom angle of either 0° or 45°. When the maximum axle load is reached e.g. to the front, the axle load to the rear is under the specified maximum axle load.

At main boom angles between 0° and 45°, the axle loads are under the specified maximum axle loads.

Maximum axle load2) in t

I - II - III - IV -V in %

Main boom angle in °

Lattice extension inclination in °

Main boom position 1)

front

rear

0-0-0-0-0

0 to 45°

0 to 40°

front

14.5

11.0

0-0-0-0-0

0 to 45°

0° to 40°

rear

10.5

12.5

0-0-0-0-0

0 to 45°

0° to 40°

front

14.0

12.0

0-0-0-0-0

0 to 45°

0° to 40°

rear

11.5

12.5

0-0-0-0-0

0 to 45°

0° to 40°

front

13.5

12.5

0-0-0-0-0

0 to 45°

0° to 40°

rear

12.5

12.5

0-0-0-0-0

0 to 45°

0° to 40°

front

13.0

13.5

0-0-0-0-0

0 to 45°

0° to 40°

rear

13.5

12.5

0-0-0-0-0

0 to 45°

0° to 40°

front

12.0

14.5

0-0-0-0-0

0 to 45°

0° to 40°

rear

14.5

12.5

0-0-0-0-0

0 to 45°

0° to 40°

front

11.5

15.0

0-0-0-0-0

0 to 45°

0° to 40°

rear

15.5

12.5)

0-0-0-0-0

0 to 45°

0° to 40°

front

11,0

16,0

0-0-0-0-0

0 to 45°

0° to 40°

rear

16,5

12,5

0-0-0-0-0

0 to 45°

0° to 40°

front

10,0

17,0

0-0-0-0-0

0 to 45°

0° to 40°

rear

18,0

12,5

Telescope status

6.6

7.6

8.6

9.6

10.6

11.6

12,6

13,6

à Information about the tables, p. 3 - 111

27.05.2014

1), 2)

3 - 112

3 113 112 en

Operating manual lattice extension GMK 3060i

8.7/15 m swing-away lattice extension 3.10 Driving with rigged crane with a rigged lattice extension

15 m swing-away lattice extension

H Counterweight in t

All the axle loads in the following table apply for hook tackle (weight 100 kg) reeved on the lattice extension.

The maximum axle load specified in the table is reached at a main boom angle of either 0° or 45°. When the maximum axle load is reached e.g. to the front, the axle load to the rear is under the specified maximum axle load.

At main boom angles between 0° and 45°, the axle loads are under the specified maximum axle loads.

I - II - III - IV -V in %

Main boom angle in °

0-0-0-0-0

0 to 45°

0 to 40°

0-0-0-0-0

0 to 45°

0-0-0-0-0

Telescope status

Lattice Main extension boom inclination position1) in °

Maximum axle load2) in t front

rear

front

15.5

10.5

0° to 40°

rear

9.5

12.5

0 to 45°

0° to 40°

front

15.0

11.5

0-0-0-0-0

0 to 45°

0° to 40°

rear

10.5

12.5

0-0-0-0-0

0 to 45°

0° to 40°

front

14.5

12.5

0-0-0-0-0

0 to 45°

0° to 40°

rear

11.5

12.5

0-0-0-0-0

0 to 45°

0° to 40°

front

13.5

13.0)

0-0-0-0-0

0 to 45°

0° to 40°

rear

13.0

12.5

0-0-0-0-0

0 to 45°

0° to 40°

front

13.0

14.0

0-0-0-0-0

0 to 45°

0° to 40°

rear

14.0

12.5

0-0-0-0-0

0 to 45°

0° to 40°

front

12.5

15.0

0-0-0-0-0

0 to 45°

0° to 40°

rear

15.0

12.5

0-0-0-0-0

0 to 45°

0° to 40°

front

12,0

16,0

0-0-0-0-0

0 to 45°

0° to 40°

rear

16,0

12,5

0-0-0-0-0

0 to 45°

0° to 40°

front

11,0

17,0

0-0-0-0-0

0 to 45°

0° to 40°

rear

17,0

12,5

6.6

7.6

8.6

9.6

10.6

11.6

12,6

13,6

1) 2)

à Information about the tables, p. 3 - 111

27.05.2014

,

Operating manual lattice extension GMK 3060i

3 113 112 en

3 - 113

8.7/15 m swing-away lattice extension 3.10 Driving with rigged crane with a rigged lattice extension

3.10.3

Driving the rigged crane Drive the truck crane as described in the Operating instructions GMK 3060i in sections – Driving from the driver's cab or – Driving from the crane cab

27.05.2014

Observe the safety instructions in those sections.

3 - 114

3 113 112 en

Operating manual lattice extension GMK 3060i

8.7/15 m swing-away lattice extension 3.11 Finding and eliminating malfunctions

3.11

Finding and eliminating malfunctions

Malfunction

Cause

Remedy

No function of the lifting limit switch

Lifting limit switch not connected

Connect the lifting limit switch; p. 3 - 76.

The connection for the lifting limit switch on the main boom head is not overridden.

Override the lifting limit switch on the main boom head; p. 3 - 76.

à

à

There is a second lifting limit switch connected to the main boom and it is not locked.

Establish the electrical p. 3 - 69. connection;

The bridging plug is not inserted in the socket to the front of section 1.

Change over the bridging p. 3 - 70. plug;

For 15 m: Electrical connection between main boom head and section 1 is not established.

Establish the electrical connection; p. 3 - 69.

Electrical connection between section 1 and section 2 is not established.

Establish the electrical connection; p. 3 - 71.

The main boom cannot be telescoped with the rigged lattice extension

The main boom is at an impermissible angle.

Derrick the main boom to the required angle; p. 3 - 99.

The lattice extension cannot be derricked

Derricking gear of the lattice extension is switched off

Switch on the derricking gear of the lattice extension; p. 3 - 2.

27.05.2014

For 8.7 m: Electrical connection between main boom head and section 1 is not established.

Operating manual lattice extension GMK 3060i

à

à

à à

à

à

The electrical connection has been broken.

Establish the electrical connection; p. 3 - 69.

The hydraulic connection has been disconnected.

Establish a hydraulic connection; p. 3 - 41.

The specified RCL code does not apply to operation with the lattice extension.

Enter the RCL code for operation with the lattice extension; p. 3 - 96.

à

à

à

Current load greater than derricking load – movement Lower lattice extension is disabled.

RCL error code 5 02 6 is displayed.

1. Raising the lattice extension.

The Driving menu on the CCS in the crane cab is open.

Close driving menu

3 113 112 en

2. If necessary, increase the working radius using the movement Lower main boom.

3 - 115

8.7/15 m swing-away lattice extension 3.11 Finding and eliminating malfunctions

27.05.2014

Blank page

3 - 116

3 113 112 en

Operating manual lattice extension GMK 3060i

8.7/15 m swing-away lattice extension 3.12 Maintenance work

3.12

Maintenance work

3.12.1

Modules in need of protection during cleaning work

• Provide protection for the following electrical parts during cleaning work: 1 the potentiometer in the joint of section 1 2 the control box at the rear of section 1 3 the control box at the front of section 1 4 the control box at the front of section 2

27.05.2014

H

Also observe all instructions contained in the chapter titled Cleaning work of the GMK 3060i in Maintenance instructions.

Operating manual lattice extension GMK 3060i

3 113 112 en

3 - 117

8.7/15 m swing-away lattice extension 3.12 Maintenance work

3.12.2

Maintenance work M1, monthly

H Pins

For lubricating the pins and support rollers, use the same grease as stated in the Maintenance manual for attach pins and socket pins; Maintenance manual GMK 3060i Maintenance overview – Maintenance Plan M1.

à

Lubricate all pins on the lattice extension, in particular: – the pins for the connection with folded-up lattice extension; – the pins of the slewing connection;

à p. 3 - 45,

à p. 3 - 55,

– the pins for the connections on the left and right of the main boom head; p. 3 - 57,

à

– the pins for the connections on the lattice extension; – the pins of the deflection sheave;

à p. 3 - 66,

à p. 3 - 72,

– the spring latch for the anti-twist device on the hose drum;

The maintenance interval applies to average operation. Also lubricate the pins after high-pressure cleaning and generally at an interval that will prevent them getting dry.

27.05.2014

H

à p. 3 - 39.

3 - 118

3 113 112 en

Operating manual lattice extension GMK 3060i

8.7/15 m swing-away lattice extension 3.12 Maintenance work

3.12.3

Maintenance work M12, every twelve months

Lubricate joints on section 1

The joints are lubricated via lubricating nipples in section 1.

In section 1 there is one lubricating nipple (1) in the pivot point.

• Clean the lubricating nipple and lubricate it with a grease gun.

27.05.2014

• Also lubricate the joint on the other side.

Operating manual lattice extension GMK 3060i

3 113 112 en

3 - 119

8.7/15 m swing-away lattice extension 3.12 Maintenance work

27.05.2014

Blank page

3 - 120

3 113 112 en

Operating manual lattice extension GMK 3060i

4 Auxiliary single-sheave boom top

4.1

Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 -

1

4.2

Installing/removing auxiliary single-sheave boom top . . . . . . . . . . . . . . . . . . . . . 4 -

3

4.2.1 4.2.2

Installing the auxiliary single-sheave boom top . . . . . . . . . . . . . . . . . . . . . . . . . 4 Removing the auxiliary single-sheave boom top . . . . . . . . . . . . . . . . . . . . . . . . 4 -

3 4

4.3

Rigging the auxiliary single-sheave boom top . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 -

5

4.3.1 4.3.2 4.3.3 4.3.4 4.3.5 4.3.6

Rigging in transport position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Rigging in working position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Attaching and removing the hoist rope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Setting the RCL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Possible reeving methods on the auxiliary single-sheave boom top . . . . . . . . 4 Lifting limit switch and anemometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 -

5 6 7 7 8 9

4.4

Operation with the auxiliary single-sheave boom top . . . . . . . . . . . . . . . . . . . . . 4 - 11

4.5

Turning loads with the auxiliary single-sheave boom top . . . . . . . . . . . . . . . . . . 4 - 13

4.5.1 4.5.2

Setting the RCL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 13 Turning a load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 15

4.6

Driving the rigged crane with a rigged auxiliary single-sheave boom top . . . . . 4 - 17

27.05.2014

4

Operating manual lattice extension GMK 3060i

3 113 112 en

27.05.2014

3 113 112 en

Operating manual lattice extension GMK 3060i

Auxiliary single-sheave boom top 4.1 Identification

4

Auxiliary single-sheave boom top

4.1

Identification The auxiliary single-sheave boom top is designed for the truck crane it was delivered with. It has the same serial number as the truck crane.

S

Risk of accidents during operation with non-modified auxiliary singlesheave boom top Operate the truck crane only with the auxiliary single-sheave boom top that has the identical serial number.

The RCL is only set for this auxiliary single-sheave boom top.

This prevents malfunctions and damage.

If you wish to use the auxiliary single-sheave boom top on several GROVE truck cranes, it needs to be adapted to the corresponding crane and marked with all the serial numbers.

S

Risk of accidents if not adjusted correctly The auxiliary single-sheave boom top should only be adjusted by your local Manitowoc Crane Care.

27.05.2014

The serial number (1) is on a plate at the front on the auxiliary single-sheave boom top.

Operating manual lattice extension GMK 3060i

3 113 112 en

4-1

Auxiliary single-sheave boom top 4.1 Identification

27.05.2014

Blank page

4-2

3 113 112 en

Operating manual lattice extension GMK 3060i

Auxiliary single-sheave boom top 4.2 Installing/removing auxiliary single-sheave boom top

4.2

Installing/removing auxiliary single-sheave boom top

H

G 4.2.1

All illustrations in this chapter show the GMK 3055. Rigging work on the GMK 3060i-1 is carried out in the same way.

Risk of accidents if the auxiliary single-sheave boom top should fall off Use appropriate materials with sufficient lifting capacities for installing and removing; Transport dimensions and weights, p. 2 - 1.

à

Installing the auxiliary single-sheave boom top On the left side of the main boom head there is a holding device.

When installing, the holding device is connected at the front bore holes (1).

• Loosen the retaining pin and remove the pin (1) from the bearing point (2).

• Use an auxiliary crane to couple to the connection eyes (3) on the auxiliary singlesheave boom head and lift it to the left onto the main boom head.

• Align the auxiliary single-sheave boom top so that the bearing point (2) lines up to the front bore holes in the holding device.

• Secure the auxiliary single-sheave boom top to the holding device using the pin (1).

• Secure the pin with a retaining pin.

• Depending on the application, bring the auxiliary single-sheave boom top into transport position or working position; Rigging the auxiliary single-sheave boom top, p. 4 - 5.

27.05.2014

à

Operating manual lattice extension GMK 3060i

3 113 112 en

4-3

Auxiliary single-sheave boom top 4.2 Installing/removing auxiliary single-sheave boom top

4.2.2

Removing the auxiliary single-sheave boom top • Use the auxiliary crane to sling the auxiliary single-sheave boom top to the connection eye (1).

In the working position, the auxiliary single-sheave boom top is positioned in front of the main boom head and is fastened with three pins (1).

• Remove the retaining pins and draw all of the pins (1) out of the bore holes and bearing points.

In the working position, the auxiliary single-sheave boom top is positioned to the side of the main boom head and is fastened with two pins (1).

• Remove the retaining pins and draw all of the pins (1) out of the bore holes and bearing points.

• Lift the auxiliary single-sheave boom top from the head of the main boom.

• Insert the two thin pins (1) and (3) into the bearing points (2) and (4) on the auxiliary single-sheave boom top.

• Insert the two pins (5) into the mounting brackets (6) at the front of the auxiliary single-sheave boom top.

27.05.2014

• Secure all the pins using retaining pins.

4-4

3 113 112 en

Operating manual lattice extension GMK 3060i

Auxiliary single-sheave boom top 4.3 Rigging the auxiliary single-sheave boom top

4.3

Rigging the auxiliary single-sheave boom top

4.3.1

Rigging in transport position On the left side of the main boom head there is a holding device.

In transport position, the boom top is connected to the rear bore holes (1) on the holding device

• Remove the retaining pins and take both pins (2) out of the bearing points (3) at the front of the main boom head.

• Insert both pins into the holders (5) and secure them with retaining pins.

• Release the retaining pin and remove the thin pin (1) from the front bearing point (4).

• Slew the auxiliary boom top to the side of the main boom head.

• Then insert the thin pin (1) into the rear bearing point (2).

• Secure the pin with a retaining pin.

27.05.2014

The auxiliary single-sheave boom top is now in transport position.

Operating manual lattice extension GMK 3060i

3 113 112 en

4-5

Auxiliary single-sheave boom top 4.3 Rigging the auxiliary single-sheave boom top

4.3.2

Rigging in working position On the left side of the main boom head there is a holding device.

In working position, the auxiliary single-sheave boom top is attached to the main boom head at both bore holes.

• Release the retaining pin and remove the thin pin (1) from the rear bearing point (2).

• Swing the auxiliary single-sheave boom top in front of the main boom head.

• Insert the thin pin (1) into the front bearing point (4) and secure it with a retaining pin.

• Remove the retaining pins and take out both thick pins (2) from the holders (5).

• Insert both pins into the bearing points (3) at the front of the main boom head and secure them with retaining pins.

27.05.2014

The auxiliary single-sheave boom top is now in working position.

4-6

3 113 112 en

Operating manual lattice extension GMK 3060i

Auxiliary single-sheave boom top 4.3 Rigging the auxiliary single-sheave boom top

4.3.3

Attaching and removing the hoist rope • Remove the cable holding rods (1) from the head of the main boom and from the auxiliary single-sheave boom top.

• When reeving, guide the hoist rope over the left head sheave of the main boom.

• Insert the rope holding rod into the appropriate bore holes and secure them with the corresponding retaining pins.

• Fasten the cable end clamp on the hook tackle or the hook block.

Reverse the sequence of operations to remove the hoist rope before slewing the auxiliary boom top into transport position.

4.3.4

Setting the RCL • On the RCL, enter the actual rigging mode for operation with the main boom. Use either the corresponding RCL code in accordance with the Lifting capacity table or via individual components.

The values given in the corresponding Lifting capacity tables for the lifting capacities decrease in this case.

The Maximum load display (1) does not show the reduced values.

27.05.2014

The RCL also takes into account the load moment affected by the rigged auxiliary single-sheave boom top and will correspondingly switch off earlier.

Operating manual lattice extension GMK 3060i

3 113 112 en

4-7

Auxiliary single-sheave boom top 4.3 Rigging the auxiliary single-sheave boom top

4.3.5

Possible reeving methods on the auxiliary single-sheave boom top The hoist rope may be reeved a maximum of 1 fall.

1-sheave hook block Maximum lifting capacity of the hook block Maximum lifting capacity with the GMK 3060i: A For reeving 1-fall

16 t

5t

Hook tackle Maximum lifting capacity of the hook tackle Maximum lifting capacity with the GMK 3060i:

5t

27.05.2014

A For reeving 1-fall

5t

4-8

3 113 112 en

Operating manual lattice extension GMK 3060i

Auxiliary single-sheave boom top 4.3 Rigging the auxiliary single-sheave boom top

4.3.6

Lifting limit switch and anemometer

For operation

• Pull the plug of the connecting cable from the dummy socket (2).

• Unwind the connecting cable from the holders (3).

• Insert the plug of the connecting cable into the socket (1) on the main boom head.

• Guide the hoist rope through the lifting limit switch weight.

If, additionally, a hook block is reeved on the main boom, connect the lifting limit switch of the main hoist to the socket on the right side of Operating the main boom head; instructions GMK 3060i.

à

For transport

• Insert the plug of the connecting cable into the dummy socket (2).

• Wind the connecting cable onto the holders (3).

• Plug the short-circuit plug into the socket (1).

Anemometer

• The anemometer is connected to the main boom head as it is for operation

à Operating instructions GMK 3060i.

27.05.2014

with the main boom;;

Operating manual lattice extension GMK 3060i

3 113 112 en

4-9

Auxiliary single-sheave boom top 4.3 Rigging the auxiliary single-sheave boom top

27.05.2014

Blank page

4 - 10

3 113 112 en

Operating manual lattice extension GMK 3060i

Auxiliary single-sheave boom top 4.4 Operation with the auxiliary single-sheave boom top

4.4

Operation with the auxiliary single-sheave boom top Operation with the auxiliary single-sheave boom top is carried out in the same way as operation with the main boom.

– The hoisting, lowering, slewing, derricking and telescoping movements are carried out in the same way as when operating with the main boom.

– When work with the auxiliary single-sheave boom top, RCL shutdowns may occur for the same reasons as when operating with the main boom; Operating instructions GMK 3060i.

à

– Strong winds lead to the truck crane being overloaded. Therefore, closely observe the instructions in the the section Effect of wind on crane operation; Operating instructions GMK 3060i.

27.05.2014

à

Operating manual lattice extension GMK 3060i

3 113 112 en

4 - 11

Auxiliary single-sheave boom top 4.4 Operation with the auxiliary single-sheave boom top

27.05.2014

Blank page

4 - 12

3 113 112 en

Operating manual lattice extension GMK 3060i

Auxiliary single-sheave boom top 4.5 Turning loads with the auxiliary single-sheave boom top

4.5

Turning loads with the auxiliary single-sheave boom top Two-hook operation is required to turn loads.

G Prerequisites

Risk of accidents due to incorrect procedure Before turning loads, observe all the prerequisites specified in this section and proceed exactly as described. This way, you avoid accidents due to overload.

– The main hoist rope is reeved on the main boom.

– The auxiliary hoist rope is reeved on the auxiliary single-sheave boom top.

– The main hoist rope is reeved with the same or a higher number of falls than the auxiliary hoist rope.

4.5.1

Setting the RCL Before lifting the load, the number of currently reeved falls of both the hoists must be entered at the RCL so that they can be immediately taken into account in case you switch between the hoists later after turning the loads.

The load must first be lifted using the auxiliary hoist. For this purpose, the RCL must first be switched over to the auxiliary hoist so that the relevant reeving is taken into account.

Proceed as follows:

• Switch off both hoists – Displays (1) and (2) are red.

• Switch the main hoist on – Display (1) is green.

27.05.2014

s Operating manual lattice extension GMK 3060i

3 113 112 en

4 - 13

Auxiliary single-sheave boom top 4.5 Turning loads with the auxiliary single-sheave boom top

• Enter the number of falls (1) currently reeved on the main hoist.

• Switch the auxiliary hoist on – Display (1) is green.

• Enter the currently reeved number of falls on the auxiliary hoist.

• Enter the RCL code that corresponds to the rigging mode as per the Lifting capacity table for the main boom; à Setting the RCL, p. 3 - 96.

The RCL now takes into account: – the reeving for the auxiliary hoist and – the Lifting capacity tables for the main boom.

27.05.2014

H

In two-hook operation, the loads given in the Lifting capacity table are reduced by the weight of both reeved hook blocks.

4 - 14

3 113 112 en

Operating manual lattice extension GMK 3060i

Auxiliary single-sheave boom top 4.5 Turning loads with the auxiliary single-sheave boom top

4.5.2

Turning a load

H

Before turning loads, check whether these procedures are in accordance with the regulations in the country in which you are working.

• Check whether all prerequisites have been met;

à Prerequisites, p. 4 - 13.

• Check whether the RCL is correctly set;

à Setting the RCL, p. 4 - 13.

G H

Risk of accidents due to overload Ensure that the RCL is set for operation with the main boom during the entire procedure and only move the load at minimum speed.

In this way you prevent the crane from becoming overloaded.

As soon as the load is on two hooks, there will be slight differences in the Current load display. However, these deviations are on the safe side with regard to RCL shutdown.

• (A) – Lift the load completely with the auxiliary single-sheave boom top (rope on the auxiliary hoist).

• (B) – Sling the load additionally at the main

27.05.2014

boom.

Operating manual lattice extension GMK 3060i

3 113 112 en

4 - 15

Auxiliary single-sheave boom top 4.5 Turning loads with the auxiliary single-sheave boom top

• (A) – Lift the load with the main hoist until both slinging points are at the same height.

• (B) – Lower the load with the auxiliary hoist until the load is completely suspended from the main hoist rope.

• Enter the RCL code that corresponds to the rigging mode as per the Lifting capacity table for main booms.

• Switch over the RCL to the main hoist.

27.05.2014

Turning the load has now been completed.

4 - 16

3 113 112 en

Operating manual lattice extension GMK 3060i

Auxiliary single-sheave boom top 4.6 Driving the rigged crane with a rigged auxiliary single-sheave boom top

4.6

Driving the rigged crane with a rigged auxiliary single-sheave boom top

G

Risk of accidents when driving from the crane cab Before driving the truck crane from the crane cab, observe all instructions in the Operating instructions GMK 3060i and set the rigging mode described there for free-on-wheels work; Operating instructions GMK 3060i.

à

When the rigging mode for the working position Free on wheels has been established in accordance with the Lifting capacity tables and the main boom is within the permitted working area, the maximum axle load which will occur when driving the rigged crane with rigged auxiliary single-sheave boom top is 24 t per axle.

• When driving with a rigged auxiliary single-sheave boom top, proceed in

à Driving the

27.05.2014

the same way as for driving with a rigged lattice extension; rigged crane, p. 3 - 114.

Operating manual lattice extension GMK 3060i

3 113 112 en

4 - 17

Auxiliary single-sheave boom top 4.6 Driving the rigged crane with a rigged auxiliary single-sheave boom top

27.05.2014

Blank page

4 - 18

3 113 112 en

Operating manual lattice extension GMK 3060i

5 Heavy load lattice extension

5.1

Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 -

1

5.2

Attaching and securing the heavy load lattice extension . . . . . . . . . . . . . . . . . . . 5 -

3

5.2.1 5.2.2 5.2.3

Slinging point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Folding in/out rope attachment point. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Securing the heavy load lattice extension with guide rope . . . . . . . . . . . . . . . . 5 -

3 4 5

5.3

Installing/removing the heavy load lattice extension . . . . . . . . . . . . . . . . . . . . . . 5 -

7

5.3.1 5.3.2

Installing the heavy load lattice extension. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Removing the heavy load lattice extension. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 -

7 9

5.4

Rigging the heavy load lattice extension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 11

5.4.1 5.4.2 5.4.3 5.4.4 5.4.5 5.4.6

Rigging in transport position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 11 Rigging in working position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 14 Setting the angle position of the heavy load lattice extension . . . . . . . . . . . . . 5 - 17 Attaching and removing the hoist rope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 20 Lifting limit switch and anemometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 22 Transportation on a separate vehicle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 23

5.5

Operation with the heavy load lattice extension . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 25

5.5.1 5.5.2 5.5.3 5.5.4 5.5.5 5.5.6

Setting the RCL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 26 Derricking the main boom. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 27 Telescoping with rigged heavy load lattice extension . . . . . . . . . . . . . . . . . . . . 5 - 28 Information about the RCL shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 29 Procedure if the permissible wind speed is exceeded . . . . . . . . . . . . . . . . . . . . 5 - 29 Information about the main boom operation when the heavy load lattice extension is folded/rigged . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 30

5.6

Turning loads with the heavy load lattice extension. . . . . . . . . . . . . . . . . . . . . . . 5 - 33

5.6.1 5.6.2

Setting the RCL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 33 Turning a load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 35

5.7

Driving with a rigged crane and rigged heavy load lattice extension . . . . . . . . . 5 - 37

27.05.2014

5

Operating manual lattice extension GMK 3060i

3 113 112 en

27.05.2014

3 113 112 en

Operating manual lattice extension GMK 3060i

Heavy load lattice extension 5.1 Identification

5

Heavy load lattice extension

5.1

Identification The heavy load lattice extension is matched to the truck crane with which it is delivered. The heavy load lattice extension belonging to the truck crane has the same serial number as the truck crane.

S

Risk of accidents during operation with non-modified heavy load lattice extension Operate the truck crane only with the heavy load lattice extension with the identical serial number.

The RCL is set only for this heavy load lattice extension.

This prevents malfunctions and damage.

If you wish to use the heavy load lattice extension on several GROVE truck cranes, the extension must be adjusted for these cranes and labelled with all of the respective serial numbers.

S

Risk of accidents if not adjusted correctly The heavy load lattice extension is to be adjusted on-site only by Manitowoc Crane Care!

27.05.2014

The serial number (1) is on the cross-strut of the heavy load lattice extension.

Operating manual lattice extension GMK 3060i

3 113 112 en

5-1

Heavy load lattice extension 5.1 Identification

27.05.2014

Blank page

5-2

3 113 112 en

Operating manual lattice extension GMK 3060i

Heavy load lattice extension 5.2 Attaching and securing the heavy load lattice extension

5.2

Attaching and securing the heavy load lattice extension

5.2.1

Slinging point

G

Risk of accidents due to the heavy load lattice extension falling down Attach the heavy load lattice extension only as described in this section to ensure that it has the right centre of gravity.

Only use appropriate lifting gear having sufficient lifting capacity; Transport dimensions and weights, p. 2 - 1.

à

• Attach the heavy load lattice extension with

27.05.2014

front of the sheave (1) at an angle of 0°.

Now the heavy load lattice extension hangs in a horizontal position on the auxiliary crane.

Operating manual lattice extension GMK 3060i

3 113 112 en

5-3

Heavy load lattice extension 5.2 Attaching and securing the heavy load lattice extension

5.2.2

Folding in/out rope attachment point

Folding out rope attachment point

For operation with a double-reeved hoist rope, you must fold out the rope attachment point.

• Hold on to the rope attachment point (3) and remove the retaining pin (2).

• Fold the rope attachment point (3) downwards.

• Insert the retaining pin into the holder (1).

S Folding in rope attachment point

Risk of damage when rope attachment point is folded out Always make sure to fold in the rope attachment point after completing operation with a double-reeved hoist rope. This prevents the rope attachment point from being damaged during operation with a single-reeved hoist rope or during transport.

For operation with a single-reeved hoist rope and for transport, you must fold in the rope attachment point.

• Remove the retaining pin (2) from the holder (1).

• Fold the rope attachment point (3) upwards.

• Secure the rope attachment point in place

27.05.2014

(3) by inserting the retaining pin into the holder (1).

5-4

3 113 112 en

Operating manual lattice extension GMK 3060i

Heavy load lattice extension 5.2 Attaching and securing the heavy load lattice extension

5.2.3

Securing the heavy load lattice extension with guide rope

G

Risk of accidents due to the heavy load lattice extension swinging of its own accord Always secure the heavy load lattice extension with a guide rope on the main boom before removing any connections.

This prevents the heavy load lattice extension from swinging around of its own accord and causing injury to you or other persons.

Secure the heavy load lattice extension in the following manner:

• Fold out the rope attachment point;

à Folding out rope attachment point, p. 5 - 4.

• Attach a guide rope to the extended rope attachment point (1).

• Have a person hold the guide rope taut while you establish or loosen pin connections on the heavy load lattice extension.

27.05.2014

H

If you happen to be alone, secure the other end of the guide rope on the crane (e.g. on the front towing coupling).

Operating manual lattice extension GMK 3060i

3 113 112 en

5-5

Heavy load lattice extension 5.2 Attaching and securing the heavy load lattice extension

27.05.2014

Blank page

5-6

3 113 112 en

Operating manual lattice extension GMK 3060i

Heavy load lattice extension 5.3 Installing/removing the heavy load lattice extension

5.3

Installing/removing the heavy load lattice extension

H

G 5.3.1

All illustrations in this chapter show the GMK 3055. Rigging work on the GMK 3060i is carried out in the same way.

Risk of accidents due to the heavy load lattice extension falling down Only use appropriate lifting gear having sufficient lifting capacity; Transport dimensions and weights, p. 2 - 1.

à

Installing the heavy load lattice extension Prerequisites: – The truck crane is on outriggers or the main boom has been placed on the boom rest.

– The required counterweight has been rigged.

– The heavy load lattice extension is at an angle of 0°.

– An auxiliary crane is available.

There is a holding device on the left side of the main boom.

The heavy load lattice extension is bolted into the front bore (1) of the holding device during the installation.

• Attach the heavy load lattice extension using an auxiliary crane in front of the top sheave (1);

à p. 5 - 3.

• Attach the guide rope to the rope attachment point (2); à p. 5 - 5.

27.05.2014

s Operating manual lattice extension GMK 3060i

3 113 112 en

5-7

Heavy load lattice extension 5.3 Installing/removing the heavy load lattice extension

• Release the retaining pin and remove the swivel pin (1) from the bearing point (2) on the heavy load lattice extension.

• Lift the heavy load lattice extension to the left on the main boom.

• Align the heavy load lattice extension so that the bearing point (2) lines up to the front boreholes in the holding device.

• Insert the swivel pin (1) through the boreholes and the bearing point (2).

• Secure the swivel pin with a retaining pin.

• Depending on the application, move the heavy load lattice extension into transport Rigging the position or working position; heavy load lattice extension, p. 5 - 11.

27.05.2014

à

5-8

3 113 112 en

Operating manual lattice extension GMK 3060i

Heavy load lattice extension 5.3 Installing/removing the heavy load lattice extension

5.3.2

Removing the heavy load lattice extension Prerequisites: – The truck crane is on outriggers or the main boom has been placed on the boomsupport.

– The required counterweight has been rigged.

– The heavy load lattice extension is at an angle of 0°.

– The hoist rope is unreeved.

– The lifting limit switch and anemometer are in transport position.

– An auxiliary crane is available.

• Attach the heavy load lattice extension using an auxiliary crane in front of the top sheave (1);

à p. 5 - 3.

• Attach the guide rope to the rope attachment point (2); à p. 5 - 5.

In working position, the heavy load lattice extension is fastened with four pins (1) in front of the main boom head.

• Remove the retaining pins and remove all of the pins (1) from the boreholes and bearing points.

In transport position, the heavy load lattice extension is secured with the swivel pin (2) and the locking pin (1) on the side of the main boom.

• Remove the retaining pins and pull out the swivel pin (2) and the locking pin (1) out of the boreholes and bearing points.

27.05.2014

s

Operating manual lattice extension GMK 3060i

3 113 112 en

5-9

Heavy load lattice extension 5.3 Installing/removing the heavy load lattice extension

• Lift the heavy load lattice extension from the main boom head.

• Insert the swivel pin (6) and the locking pin (5) in the bearing points (3) and (4) on the heavy load lattice extension.

• Insert the four connecting pins (1) in the holders (2) on the heavy load lattice extension.

• Secure all pins with retaining pins.

• Fold in the rope attachment point;

27.05.2014

à Folding in rope attachment point, p. 5 - 4.

5 - 10

3 113 112 en

Operating manual lattice extension GMK 3060i

Heavy load lattice extension 5.4 Rigging the heavy load lattice extension

5.4

Rigging the heavy load lattice extension

5.4.1

Rigging in transport position Prerequisites: – The truck crane is on outriggers or the main boom has been placed on the boomsupport.

– Heavy load lattice extension in working position.

– Heavy load lattice extension is at an angle of 0°.

– The hoist rope is unreeved.

In transport position, the heavy load lattice extension is folded on the side of the main boom and secured with the swivel pin (2) and the locking pin (1).

• Attach the guide rope to the rope attachment point (1); à p. 5 - 5.

• Remove the retaining pin and pull the swivel pin out of the bearing point (1).

• Remove the retaining pins and pull both connecting pins (2) out of the bearing points (3) and (5) on the right side of the main boom head.

• Insert both pins into the holders (4) and secure them with retaining pins.

27.05.2014

s

Operating manual lattice extension GMK 3060i

3 113 112 en

5 - 11

Heavy load lattice extension 5.4 Rigging the heavy load lattice extension

• Swivel the heavy load lattice extension onto the main boom until the bearing point (1) and the boreholes align.

G

Risk of accidents due to the heavy load lattice extension falling down Always insert the swivel pin into the holding device first before removing the connecting pins. This way, you can avoid the heavy load lattice extension having no connection with the main boom and falling down.

• Secure the heavy load lattice extension with the swivel pin (2) at the front borehole.

• Secure the swivel pin (2) with a retaining pin.

• Release the retaining pin and pull the locking pin out of the bearing point (1).

• Release the retaining pins and pull both of the connecting pins (4) out of the bearing points (5) and (7) on the left side of the main boom.

• Insert both pins into the holders (6) and secure them with retaining pins.

• Swivel the heavy load lattice extension around the swivel pin until the

27.05.2014

bearing point (1) and the boreholes align.

5 - 12

3 113 112 en

Operating manual lattice extension GMK 3060i

Heavy load lattice extension 5.4 Rigging the heavy load lattice extension

• Secure the heavy load lattice extension with the locking pin (1) on the holding device.

• Secure it with a retaining pin.

• Detach the guide rope from the rope attachment point (1).

• Fold in the rope attachment point;

à Folding in rope attachment point, p. 5 - 4.

27.05.2014

The heavy load lattice extension is now in transport position.

Operating manual lattice extension GMK 3060i

3 113 112 en

5 - 13

Heavy load lattice extension 5.4 Rigging the heavy load lattice extension

5.4.2

Rigging in working position Prerequisites: – The truck crane is on outriggers or the main boom has been placed on the boomsupport.

– Heavy load lattice extension in transport position.

– The required counterweight has been rigged.

In working position, the heavy load lattice extension is secured with four connecting pins (1) in front of the main boom head.

• Remove the retaining pin and fold out the rope attachment point (1);

à p. 5 - 4.

• Attach the guide rope to the rope attachment point (1); à p. 5 - 5.

• Release the retaining pin and pull the lock-

27.05.2014

ing pin out of the bearing point (1).

5 - 14

3 113 112 en

Operating manual lattice extension GMK 3060i

Heavy load lattice extension 5.4 Rigging the heavy load lattice extension

• Swivel the heavy load lattice extension onto the main boom until the bearing point (1) and the boreholes align.

G

Risk of accidents due to the heavy load lattice extension falling down Always first insert the connecting pin in the main boom head before removing the connecting pin. This way, you can avoid the heavy load lattice extension having no connection with the main boom and falling down.

• Remove the retaining pins and pull both of the connecting pins (4) out of the holders (6).

• Attach the heavy load lattice extension with the connecting pins (4) to the left side of the main boom head and secure them with retaining pins.

• Insert the locking pin (1) into the bearing point (2) and secure it with a retaining pin.

• Remove the retaining pin and pull the swivel pin out of the bearing point (3).

• Swivel the heavy load lattice extension onto the main boom until the bearing points (1) and the boreholes align.

27.05.2014

s

Operating manual lattice extension GMK 3060i

3 113 112 en

5 - 15

Heavy load lattice extension 5.4 Rigging the heavy load lattice extension

• Remove the retaining pins and pull both of the connecting pins (4) out of the holders (5).

• Insert both connecting pins (4) in the bearing points (3) on the right side of the main boom head and secure them with retaining pins.

• Insert the swivel pin (1) in the bearing point (2) and secure it with a retaining pin.

For operation with a double-reeved hoist rope

• Reeve the hook block accordingly, and fasten the hoist rope to the rope attachment point;

à Operating instructions GMK 3060i.

For operation with a single-reeved hoist rope

• Fold in the rope attachment point; à p. 5 - 4.

S

Risk of damage when rope attachment point is folded out Always make sure to fold in the rope attachment point for operation with a single-reeved hoist rope.

This prevents it from being damaged during operation.

• Reeve the hook block accordingly; à Operating instructions GMK 3060i.

27.05.2014

The heavy load lattice extension is now in working position.

5 - 16

3 113 112 en

Operating manual lattice extension GMK 3060i

Heavy load lattice extension 5.4 Rigging the heavy load lattice extension

5.4.3

Setting the angle position of the heavy load lattice extension Depending on requirements, the heavy load lattice extension can be used at two different angles.

– 0° angle, also transport position

– 40° angle

Installing/ removing the chain hoist

G

Two different angles (0° and 40°) can be set on the heavy load lattice extension. The chain hoist supplied with the truck crane is used for these settings.

Risk of uncontrolled movements When removing the chain hoist, the pin must be always inserted in the tie member and secured with a retaining pin. This way, you can prevent the heavy load lattice extension from folding down in an uncontrolled manner.

Installation • Attach the chain hoist (3) at the slinging points (2) and (4).

Removal The pin (1) is inserted and secured with a retaining pin.

• Unload the chain hoist (3).

• Remove the chain hoist at the slinging points (2) and (4).

27.05.2014

s Operating manual lattice extension GMK 3060i

3 113 112 en

5 - 17

Heavy load lattice extension 5.4 Rigging the heavy load lattice extension

Prerequisites

– The main boom is set down in the boom rest.

– The heavy load lattice extension has been pinned in front of the main boom head.

Setting 40° angle

S

Risk of uncontrolled movements When setting working positions, always lift or swing the heavy load lattice extension as far as possible and then insert the pin. This way, you can prevent the heavy load lattice extension from being in a non-permissible position without a fall-back guard.

• Hook in the chain hoist, à p. 5 - 17.

• Lift the heavy load lattice extension with the chain hoist until the pin (1) is relieved.

• Release the retaining pin and pull the pin (1) out of the bearing point (3).

• Lower the heavy load lattice extension as far as possible using the chain hoist.

• Insert the pin (1) into the bearing point (4) and secure it with the retaining pin.

• Detach the chain hoist; à p. 5 - 17.

27.05.2014

• Insert the hoist rope; à p. 5 - 20.

5 - 18

3 113 112 en

Operating manual lattice extension GMK 3060i

Heavy load lattice extension 5.4 Rigging the heavy load lattice extension

Setting 0° angle

• Remove the hoist rope from the heavy load lattice extension.

• Hook in the chain hoist (2); à p. 5 - 17.

• Lift the heavy load lattice extension using the chain hoist (2), until the pin (1) is no longer under load.

• Release the retaining pin and remove the pin (1) from the bearing point (4).

• Lift the heavy load lattice extension as far as it will go using the chain hoist (2).

• Insert the pin (1) into the bearing point (3) and secure it with a retaining pin.

27.05.2014

• Detach the chain hoist; à p. 5 - 17.

Operating manual lattice extension GMK 3060i

3 113 112 en

5 - 19

Heavy load lattice extension 5.4 Rigging the heavy load lattice extension

5.4.4

Attaching and removing the hoist rope • Remove the hoist rope protection rolls (3) and rods (1) from the main boom head and from the heavy load lattice extension.

• Lead the hoist rope over the deflection sheave (2) and the head sheave (4) of the heavy load lattice extension.

• Insert the hoist rope protection rolls (3) and rods (1) in the corresponding boreholes and secure them with the respective retaining pins.

• Install the hook tackle or the hook block.

The hoist rope can be reeved once or twice; p. 5 - 21.

à

For double reeving, the hoist rope is attached to the rope attachment point (6).

S

Risk of damage when rope attachment point is folded out Always make sure to fold in the rope attachment point for operation with a single-reeved hoist rope.

This prevents it from being damaged during operation.

27.05.2014

Carry out the sequence of operations in the reverse order to remove the hoist rope before slewing the heavy load lattice extension into transport position.

5 - 20

3 113 112 en

Operating manual lattice extension GMK 3060i

Heavy load lattice extension 5.4 Rigging the heavy load lattice extension

Possible reeving methods on the heavy load lattice extension

The hoist rope can be reeved once or twice.

1-sheave hook block Maximum lifting capacity of the hook block Maximum lifting capacity with the GMK 3060i:

16 t

A For reeving 2-fall

10 t

B For reeving 1-fall

5t

Hook tackle Maximum lifting capacity of the hook tackle Maximum lifting capacity with the GMK 3060i: A For reeving 1-fall

5t

5t

27.05.2014

Reeving the hoist rope on the hook block; à Operating instructions GMK 3060i.

Operating manual lattice extension GMK 3060i

3 113 112 en

5 - 21

Heavy load lattice extension 5.4 Rigging the heavy load lattice extension

5.4.5

Lifting limit switch and anemometer

For operation

• Hook the lifting limit switch (5) in the holder (4) and secure it with a retaining pin.

• Pull the plug of the connecting cable from the dummy socket (2).

• Unwind the connecting cable from the holders (3).

• Insert the plug of the connecting cable into the socket (1) on the main boom head.

• Put the hoist rope through the lifting limit switch weight; GMK 3060i.

à Operating instructions

If, additionally, a hook block is reeved on the main boom, connect the lifting limit switch of the main hoist to the socket on the right side of the main boom head; Operating instructions GMK 3060i.

à

For transport

• Pull the plug of the connecting cable from the socket (1) and insert it in the dummy socket (2).

• Wind the connecting cable onto the holders (3).

27.05.2014

• Plug the short-circuit plug into the socket (1).

5 - 22

3 113 112 en

Operating manual lattice extension GMK 3060i

Heavy load lattice extension 5.4 Rigging the heavy load lattice extension

Anemometer

• The anemometer is connected to the main boom head as it is for operation with the main boom;

5.4.6

à Operating instructions GMK 3060i.

Transportation on a separate vehicle For driving on public roads with a maximum 12 t axle load, the heavy load lattice extension on the main boom must be removed and set on a separate vehicle.

G

Risk of injury Attach the lattice extension only at the designated points and use only lifting gear with sufficient load lifting capacity.

This prevents the heavy load lattice extension from falling and injuring peoSlinging point, p. 5 - 3. ple while loading;

à

• Fold in the rope attachment point for transportation, and secure it in place using the retaining pin;

à p. 5 - 4.

• For transport, set the lattice extension down so as not to damage it.

• Always secure the heavy load lattice extension on the separate vehicle ad-

27.05.2014

ditionally with belts to prevent slipping and overturning.

Operating manual lattice extension GMK 3060i

3 113 112 en

5 - 23

Heavy load lattice extension 5.4 Rigging the heavy load lattice extension

27.05.2014

Blank page

5 - 24

3 113 112 en

Operating manual lattice extension GMK 3060i

Heavy load lattice extension 5.5 Operation with the heavy load lattice extension

5.5

Operation with the heavy load lattice extension

H

G

During operation with the lattice extension, the speed for all power units is limited to 70%.

Risk of accidents due to falling chain hoist Always detach the chain hoist before operation with the heavy load lattice extension.

This prevents the chain hoist from falling and injuring persons or damaging the truck crane.

The hoisting, lowering, slewing, derricking and telescoping movements are carried out in the same way as when operating with the main boom. This section only contains information that you will need for a rigged or installed heavy load lattice extension:

à Setting the RCL, p. 5 - 26, à Derricking the main boom, p. 5 - 27, à Telescoping with rigged heavy load lattice extension, p. 5 - 28, à Information about the RCL shutdown, p. 5 - 29, à Information about the main boom operation when the heavy load lattice extension is folded/rigged, p. 5 - 30,

à Information about the main boom operation when the heavy load lattice extension is folded/rigged, p. 5 - 30,

27.05.2014

à Information about the RCL shutdown, p. 5 - 29.

Operating manual lattice extension GMK 3060i

3 113 112 en

5 - 25

Heavy load lattice extension 5.5 Operation with the heavy load lattice extension

5.5.1

Setting the RCL

H

If a hook block is reeved on the main boom during operation with the heavy load lattice extension, the loads given in the Lifting capacity tables decrease and the RCL switches off earlier.

The values which must be deducted from the load capacities depend on the length of the lattice extension and the weight of the hook block. You will find a table with the values in the Lifting capacity tables in the Section Remarks about working with the heavy load lattice extension.

For the heavy load lattice extension, the length and the set angle of the heavy load lattice extension are also entered and displayed.

• Enter the current reeving at the RCL. • Enter the current rigging mode on the RCL, either using the corresponding RCL code according to the Lifting capacity table or using the individual components.

• Check whether the current rigging mode of the truck crane corresponds to the displayed rigging mode.

• Check: 1 the set angle of the heavy load lattice extension (e.g. 20°) 2 the length of the rigged lattice extension, here 2 m

X.X° X.Xt

X.XXm

3 the hoist that is switched on

X.Xt

4 the number of reeved rope lines

X.X%

X.Xm

X.X°

5 the rigged outrigger span

X.Xm

X.XXt

6 the rigged counterweight

X.X° X.Xm

Xm

Xm

Xm

Xm

– The display (7) shows the RCL code as per the Lifting capacity table.

If the telescopic sections are mechanically locked, the RCL will release the load according to the Lifting capacity table and the Maximum load display (1) shows the corresponding value.

27.05.2014

Otherwise, only the value for the empty-hook curve is released and displayed.

5 - 26

3 113 112 en

Operating manual lattice extension GMK 3060i

Heavy load lattice extension 5.5 Operation with the heavy load lattice extension

5.5.2

G

Derricking the main boom Risk of accidents if the RCL is overridden Do not override the RCL when lowering the boom into horizontal position.

If the RCL is overridden, the crane operation will not be monitored and the truck crane will overturn if it moves outside of the permissible working range.

If the following prerequisites are met, lowering into the horizontal position with heavy load lattice extension and a slewing range of 360° is permitted and is monitored by the RCL. – The current rigging mode with the rigged heavy load lattice extension is entered on the RCL, and the corresponding RCL code is displayed as per the Lifting capacity table.

– The current reeving type on the swing-away lattice extension is entered for the hoisting gear whose hoist rope is reeved on the heavy load lattice extension.

– Apart from the hook block, there is no load on the heavy load lattice extension.

– The main boom is fully retracted.

The RCL will only release the main boom for raising and setting it down when the main boom is completely retracted.

27.05.2014

When all of the above prerequisites have been satisfied, the RCL will automatically switch to the rigging tables and derricking is then also permitted within the angle range that is below the working range of approx. 65°.

Operating manual lattice extension GMK 3060i

3 113 112 en

5 - 27

Heavy load lattice extension 5.5 Operation with the heavy load lattice extension

5.5.3

S

Telescoping with rigged heavy load lattice extension Risk of overloading the main boom If you are telescoping the main boom with the rigged heavy load lattice extension, you may not simultaneously slew the superstructure.

This prevents the main boom being subjected to additional side forces and increased vibration and becoming overloaded.

The telescoping of the main boom with a rigged heavy load lattice extension is monitored by the RCL. The telescoping will only be released if the main boom is derricked to a certain angle and a maximum permissible load is not exceeded.

The required angle (between 60° and 70°) depends on: – the angle of the heavy load lattice extension – the extended length of the main boom – the rigged counterweight – the rigged outrigger span You will find the required main boom angle and maximum permissible load (weight of the hook block) in the Lifting capacity tables, in the Chapter Rigging tables – Heavy load lattice extension.

If the main boom angle is too small for telescoping with the heavy load lattice extension, the RCL displays a appropriate error message.

27.05.2014

The telescoping mechanism is operated in the same way as the main boom; à Operating instructions GMK 3060i – Telescoping mechanism.

5 - 28

3 113 112 en

Operating manual lattice extension GMK 3060i

Heavy load lattice extension 5.5 Operation with the heavy load lattice extension

5.5.4

Information about the RCL shutdown The operation with the heavy load lattice extension is monitored by the RCL. RCL shutdowns can occur during operation with the lattice extension for the same reasons as shutdowns occurring during operation with the main Operating instructions GMK 3060i. boom;

à

5.5.5

G

Procedure if the permissible wind speed is exceeded Risk of accidents from excessively high wind speeds If the current wind speed is higher than the maximum permissible wind speed, cease crane operation immediately and set up the corresponding rigging mode.

This will prevent the truck crane from overturning due to overload.

• Prior to and during crane operation, check whether the current wind speed is lower than the maximum permissible wind speed.

• Make sure that you follow the instructions for checking the wind speed;

à Lifting capacity table and Operating instructions GMK 3060i.

If the maximum permitted wind speed is exceeded No automatic shutdown occurs if the maximum permissible wind speed is exceeded.

• Immediately cease crane operation.

• Put the truck crane into the rigging mode specified for the current wind

27.05.2014

speed in the Lifting capacity table.

Operating manual lattice extension GMK 3060i

3 113 112 en

5 - 29

Heavy load lattice extension 5.5 Operation with the heavy load lattice extension

5.5.6

Information about the main boom operation when the heavy load lattice extension is folded/rigged

Folded

This section applies to instances when the heavy load lattice extension is folded at the side.

If the heavy load lattice extension is folded at the side during operation with the main boom, the loads given in the Lifting capacity tables decrease.

The relevant formulas and examples for calculating these values during operations planning can be found in the Lifting capacity tables in the Section Remarks about working with the heavy load lattice extension.

The decreased values are shown directly on the RCL insert in the Maximum load display (1).

Rigged

G

This section applies to instances when the heavy load lattice extension is rigged and locked at the front to the main boom head.

Risk of overturning with impermissible rigging mode Main boom operation with a rigged heavy load lattice extension is only permissible in rigging modes that are also permissible for the rigged heavy load lattice extension (outrigger span, counterweight, slewing range).

If you set up rigging modes that are only valid for main boom operation without a rigged heavy load lattice extension (e.g. Free on wheels working position), there is the danger of the truck crane overturning during operation.

For operation with the main boom with a rigged heavy load lattice extension, you must enter the current rigging mode for the main boom without a heavy load lattice extension on the RCL.

27.05.2014

In this case, the values given in the corresponding Lifting capacity tables for the lifting capacities decrease.

5 - 30

3 113 112 en

Operating manual lattice extension GMK 3060i

Heavy load lattice extension 5.5 Operation with the heavy load lattice extension

Reduction of the lifting capacity The Maximum load display (1) does not show the reduced values.

The RCL also takes into account the load moment affected by the rigged heavy load lattice extension and switches off earlier.

In the Lifting capacity tables you will find tables with values for the reduction of the lifting capacities in the Section Remarks about working with the heavy load lattice extension. The given values for reduction are only maximum values for certain rigging modes (angle and length of main boom and lattice extension).

The RCL, however, takes into account the value for the currently rigged heavy load lattice extension, adds the weight of the raised load and displays the sum on the Current load display (1).

The displayed value could deviate from the value that was previously calculated during the operations planning.

If this is the case, the RCL is not defective. Do not override the RCL, even if the displayed value is higher than the calculated value.

27.05.2014

G

Risk of accidents when RCL is overridden Never override the RCL. If the RCL is overridden, the crane operations will not be monitored and the truck crane will overturn if you leave the permissible working range.

Operating manual lattice extension GMK 3060i

3 113 112 en

5 - 31

Heavy load lattice extension 5.5 Operation with the heavy load lattice extension

27.05.2014

Blank page

5 - 32

3 113 112 en

Operating manual lattice extension GMK 3060i

Heavy load lattice extension 5.6 Turning loads with the heavy load lattice extension

5.6

Turning loads with the heavy load lattice extension Two-hook operation is required to turn loads.

G Prerequisites

Risk of accidents due to incorrect procedure Before turning loads, observe all the prerequisites specified in this section and proceed exactly as described. This way, you avoid accidents due to overload.

– The main hoist rope is reeved on the main boom.

– The auxiliary hoist rope is reeved on the lattice extension.

– The main hoist rope is reeved with the same or a higher number of falls than the auxiliary hoist rope.

5.6.1

Setting the RCL

Switching on the auxiliary hoist and entering the reeving

Before lifting the load, the number of currently reeved falls of both the hoists must be entered at the RCL so that they can be immediately taken into account in case you switch between the hoists later after turning the loads.

The load must first be lifted using the auxiliary hoist. For this purpose, the RCL must first be switched over to the auxiliary hoist so that the relevant reeving is taken into account.

Proceed as follows:

• Switch off both hoists – Displays (1) and (2) are red.

• Switch the main hoist on – Display (1) is green.

• Enter the number of falls (1) currently reeved on the main hoist.

27.05.2014

s Operating manual lattice extension GMK 3060i

3 113 112 en

5 - 33

Heavy load lattice extension 5.6 Turning loads with the heavy load lattice extension

• Switch the auxiliary hoist on – Display (1) is green.

• Enter the currently reeved number of falls on the auxiliary hoist.

• Enter the correct RCL code for the rigging mode as per the Lifting capacity table for the heavy load lattice extension; à Setting the RCL, p. 5 - 26.

The RCL now takes into account: – the reeving for the auxiliary hoist and – the Lifting capacity tables for the heavy load lattice extension.

27.05.2014

H

In two-hook operation, the loads given in the Lifting capacity table are reduced by the weight of both reeved hook blocks.

5 - 34

3 113 112 en

Operating manual lattice extension GMK 3060i

Heavy load lattice extension 5.6 Turning loads with the heavy load lattice extension

5.6.2

Turning a load

H

Before turning loads, check whether these procedures are in accordance with the regulations in the country in which you are working.

• Check whether all prerequisites have been met;

à Prerequisites, p. 5 - 33.

• Check whether the RCL is correctly set;

à Setting the RCL, p. 5 - 33.

G H

Risk of accidents due to overload Ensure that the RCL is set for operation with the lattice extension during the entire procedure and only move the load at minimum speed.

In this way you prevent the crane from becoming overloaded.

As soon as the load is on two hooks, there will be slight deviations in the Current load display. However, these deviations are on the safe side with regard to RCL shutdown.

• (A) – Lift the load completely with the heavy load lattice extension (rope on the auxiliary hoist).

• (B) – Sling the load additionally at the main

27.05.2014

boom.

Operating manual lattice extension GMK 3060i

3 113 112 en

5 - 35

Heavy load lattice extension 5.6 Turning loads with the heavy load lattice extension

• (A) – Lift the load with the main hoist until both slinging points are at the same height.

• (B) – Lower the load with the auxiliary hoist until the load is completely suspended from the main hoist rope.

• Enter the RCL code that corresponds to the rigging mode as per the Lifting capacity table for main booms.

• Switch the RCL to the main hoist.

27.05.2014

Turning the load has now been completed.

5 - 36

3 113 112 en

Operating manual lattice extension GMK 3060i

Heavy load lattice extension 5.7 Driving with a rigged crane and rigged heavy load lattice extension

5.7

Driving with a rigged crane and rigged heavy load lattice extension

G

Risk of accidents when driving from the crane cab Before driving the truck crane from the crane cab, observe all instructions of the Operating instructions GMK 3060i and set the rigging mode described there for free-on-wheels work; Operating instructions GMK 3060i – Driving the truck crane from the crane cab.

à

When the rigging mode for the working position Free on wheels has been established in accordance with the Lifting capacity tables and the main boom is within the permitted working area, the maximum axle load which will occur when driving the rigged crane with rigged heavy load lattice extension is 24 t per axle.

When driving with a rigged heavy load lattice extension, proceed in the same way as for driving with a rigged lattice extension; Driving the rigged crane, p. 3 - 114.

27.05.2014

à

Operating manual lattice extension GMK 3060i

3 113 112 en

5 - 37

Heavy load lattice extension 5.7 Driving with a rigged crane and rigged heavy load lattice extension

27.05.2014

Blank page

5 - 38

3 113 112 en

Operating manual lattice extension GMK 3060i

6 Index

27.05.2014

6

Operating manual lattice extension GMK 3060i

3 113 112 en

27.05.2014

3 113 112 en

Operating manual lattice extension GMK 3060i

Index

6

Index The index has the following structure: The names of parts or modules you are searching for are listed in alphabetical order on the left. The following are indented under these terms: – Operations (e.g. Positioning/removing the hoist rope) or – Subcategories (e.g. Transport) or – Subcategories related to operations (e.g. Swivel lattice extension).

27.05.2014

H

The first search word is always a noun which is followed by an operation or a subcategory.

Operating manual lattice extension GMK 3060i

3 113 112 en

6-1

Index

27.05.2014

Blank page

6-2

3 113 112 en

Operating manual lattice extension GMK 3060i

27.05.2014

Index

A

Auxiliary single-sheave boom top driving with rigged auxiliary single-sheave boom top . . . . . . . . . . . . . . . . . . . 4 - 17 identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 1 installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 3 removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 4 rigging in transport position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 5 in working position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 6 positioning/removing the hoist rope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 7 possible reeving methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 8 setting the SLI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 7 transport dimensions and weights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 1 Turning loads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 13 Axle loads when driving with rigged auxiliary single-sheave boom top . . . . . . . . . . . . . . 4 - 17 when driving with rigged swing-away lattice extension . . . . . . . . . . . . . . . . 3 - 110

E

Electrical system on the swing-away lattice extension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 69

H

Heavy load lattice extension driving with rigged heavy load lattice extension . . . . . . . . . . . . . . . . . . . . . . . 5 - 37 folding in rope attachment point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 4 folding out rope attachment point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 4 identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 1 installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 7 operation information about the SLI shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 29 main boom operation when the heavy load lattice extension is folded/rigged .

5 - 30 telescoping with rigged heavy load lattice extension . . . . . . . . . . . . . . . . . 5 - 28 possible reeving methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 21 removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 9 rigging in working position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 14 installing/removing the lifting limit switch and anemometer . . . . . . . . . . 5 - 22 positioning/removing the hoist rope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 20 setting the angle position installing/removing the chain hoist . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 17 setting 0° angle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 19 setting 40° angle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 18 securing with guide rope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 5 slinging point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 3 transport dimensions and weights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 1 transport on separate vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 23 turning loads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 33 Hoist rope possible reeving methods on the auxiliary single-sheave boom top . . . . . . . . 4 - 8

Operating manual lattice extension GMK 3060i

3 113 112 en

6-3

Index

6-4

I

Identification auxiliary single-sheave boom top . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 1 of the heavy load lattice extension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 1 of the swing-away lattice extension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 7

L

Lattice extension Additional operating and display elements on the hand-held control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 5 additional operating and display elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 1 in the crane cab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 2 centres of gravity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 10 CHECKLIST installing 8.7/15 m swing-away lattice extension . . . . . . . . . . . . . . . . . . . . 3 - 12 removing 8.7/15 m swing-away lattice extension . . . . . . . . . . . . . . . . . . . . 3 - 14 rigging the 8.7/15 m swing-away lattice extension . . . . . . . . . . . . . . . . . . . 3 - 19 unrigging the 8.7/15 m swing-away lattice extension . . . . . . . . . . . . . . . . . 3 - 25 composition of the swing-away lattice extension . . . . . . . . . . . . . . . . . . . . . . . . 3 - 9 driving with rigged lattice extension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 109 boom positions and axle loads – GMK 3055 . . . . . . . . . . . . . . . . . . . . . . . 3 - 110 driving distance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 110 driving the rigged crane . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 114 finding and eliminating malfunctions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 115 identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 7 maintenance work maintenance work M1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 118 maintenance work M12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 119 modules in need of protection during cleaning work . . . . . . . . . . . . . . . . 3 - 117 Operation Procedure if permissible wind speeds are exceeded . . . . . . . . . 3 - 101, 5 - 29 operation derricking the lattice extension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 85 information about the SLI shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 100 main boom operation when the lattice extension is folded/rigged . . . . . 3 - 102 setting the SLI for hydraulically derricking lattice extensions . . . . . . . . . . . . . . . . . . . . 3 - 96 for manually inclinable lattice extensions . . . . . . . . . . . . . . . . . . . . . . . 3 - 97 telescoping with rigged lattice extension . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 99 overview of the required rigging work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 11 rigging work air traffic control light installing/removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 81 anti-twist device on the hose drum . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 39 checking the transport condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 33

3 113 112 en

Operating manual lattice extension GMK 3060i

27.05.2014

possible reeving methods on the heavy load lattice extension . . . . . . . . . . . . 5 - 21 possible reeving methods on the swing-away lattice extension . . . . . . . . . . . 3 - 75 Hydraulic system on the lattice extension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 41

Index

connecting/disconnecting the slewing connection . . . . . . . . . . . . . . . . . . . 3 - 55 connections with folded lattice extension in the Front 1 area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 45 in the Front 2 area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 47 in the middle area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 49 in the rear area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 51 derricking the lattice extension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 83 when rigging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 83 establishing/disconnecting the electrical connection . . . . . . . . . . . . . . . . . 3 - 69 establishing/disconnecting the hydraulic connection . . . . . . . . . . . . . . . . . 3 - 41 establishing/releasing connections on the lattice extension . . . . . . . . . . . 3 - 66 guides and holders for the hydraulic hoses . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 43 installing/removing the anemometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 79 installing/removing the lifting limit switch . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 76 positioning/removing the hoist rope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 74 preparing the truck crane for rigging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 31 securing lattice extension with cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 32 securing/releasing section 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 53 setting the angle – with the auxiliary crane . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 86 setting the angle – without the auxiliary crane . . . . . . . . . . . . . . . . . . . . . . 3 - 88 swivelling the lattice extension when rigging when rigging section 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 61 when rigging section 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 63 when unrigging section 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 62 when unrigging section 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 64 unfolding/folding the deflection sheave . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 72 transport dimensions and weights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 1 transporting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 94 validity of the chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 1 Loads, turning with the heavy load lattice extension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 33

Maintenance work on the lattice extension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 117 Malfunctions when working with the swing-away lattice extension . . . . . . . . . . . . . . . . . . 3 - 115

O

Operating instructions for lattice extension basic safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 2 important information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 1 intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 3 organizational measures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 5 personnel qualifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 7 safety indications for crane work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 8

P

Possible reeving methods

27.05.2014

M

Operating manual lattice extension GMK 3060i

3 113 112 en

6-5

Index

auxiliary single-sheave boom top . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 8 on the heavy load lattice extension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 21 on the swing-away lattice extension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 75

Safety indications warnings and symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 2 Short description of the operating elements on the swing-away lattice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 6 Swing-away lattice Operating elements on the swing-away lattice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 6 Swing-away lattice extension, see Lattice extension

T

Transport dimensions and weights 8.7/15 m swing-away lattice extension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 1 auxiliary single-sheave boom top . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 1 heavy load lattice extension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 1 Transporting of the heavy load lattice extension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 23 the 8.7/15 m swing-away lattice extension . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 33 the auxiliary single-sheave boom top . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 5 Turning loads with the auxiliary single-sheave boom top . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 13 with the swing-away lattice extension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 105

27.05.2014

S

6-6

3 113 112 en

Operating manual lattice extension GMK 3060i