Frontier Manure Spreder MS1442H MS1455H Operator's Manual(5HPOMSP8) - PDF DOWNLOAD

OPE RATOR ’ S

MANUAL

MS1442H MS1455H

HSMFG0406 Rev. 3

5HPOMSP8

TABLE OF CONTENTS TABLE OF CONTENTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . INSIDE COVER WARRANTY & NOTES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 DEALER PRE-DELIVERY & DELIVERY CHECKLIST. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 BOLT TORQUE CHART. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 BE ALERT SYMBOL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 SAFETY RULES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9 DANGER - WARNING DECALS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-12 OPERATION MS1442H & MS1455H. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-14 ADJUSTMENTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 BEATERS REMOVAL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 LUBRICATION GUIDE MS1442H & MS1455H. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17-19 DECAL LOCATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20-21 TROUBLE SHOOTING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 OPTIONAL EQUIPMENT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 ORDERING PARTS - ABOUT IMPROVEMENTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 PARTS LISTS & DIAGRAMS MS1442H & MS1455H. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24-46 OPTIONAL REAR PAN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47 SERVICE RECORDS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48

WARRANTY: Warranty coverage is provided by John Deere according to the terms of the Agricultural/Commercial & Consumer Equipment Warranty Statement. Carefully read the warranty statement on the back of your original purchase order for details on coverage and limitations of this warranty.

NOTES

-1-

AFTER COMPLETION, DEALER SHOULD REMOVE AND RETAIN FOR RECORDS FRONTIER DEALER PRE-DELIVERY CHECK LIST After the Manure Spreader has been completely set-up, check to be certain it is in correct running order before delivering to the customer. The following is a list of points to inspect. Check off each item as you have made the proper adjustments and found the item operating satisfactorily.

PTO shields turn freely.

All Shields and Guards are in place and fastened.

All grease fittings have been lubricated and gearbox filled to proper level See lubrication guide in this manual.

All mechanisms are operating trouble free.

All roller chains are at proper tension.

All bolts and fasteners are tight.

All decals are in place and legible.

(Dealer’s Name)

Model Number Serial Number

(Signature of Pre-Delivery Inspector)

(Inspection Date)

DEALER DELIVERY CHECK LIST This check list that follows is an important reminder of valuable information that should be passed on to the customer at the time this Manure Spreader is delivered.

Check off each item as you explain it to the customer.

This delivery check list, when properly filled out and signed assures the customer that the Pre-delivery service was satisfactorily performed.

Explain to the customer that the pre-delivery inspection was made.

Explain to the customer all the safety precautions they must excercise when operating this unit.

Explain recommended loads for different types of materials.

Explain to customer that regular lubrication is required for proper operation and long life of machine. Show customer the lubrication section of Operators Manual.

Give the customer Operators Manual and make sure he reads and understands all operating and service instructions.

Record Serial Number on page 23 of this Manual.

Date Delivered

Dealer’s Name By

Signature of Original Buyer

-3-

FRONTIER MODEL MS1442H & MS1455H MANURE SPREADER Your Frontier spreader has been manufactured of the finest quality materials and components. The performance you get from your machine is largely dependent upon how well you read and understand this manual and apply this knowledge. There is a right and a wrong way to do everything. Please do not assume that you know how to operate and maintain your spreader before reading this manual carefully. Keep this manual available for ready reference.

S P E C I F I C AT I O N S HORIZONTIAL BEATERS

VERTICAL BEATERS

MS1442H MS1455H MS1442H MS1455H Capacity (Old Rating). . . . . . . . . . . . . . . . . . . 425 Bu. . . . . . 550 Bu. . . . . . 425 Bu. . . . . . 550 Bu. Capacity Cu. Ft. Struck Level. . . . . . . . . . . . . 270. . . . . . . . . 430. . . . . . . . . 270. . . . . . . . . 430 Side Loading Height. . . . . . . . . . . . . . . . . . . . 61-1/4” . . . . . . 81”. . . . . . . . . 61-1/4”. . . . . . 81” Overall Height Top of 2nd Beater or Vertical. . 74-3/4” . . . . . . 86-3/4”. . . . . . N/A. . . . . . . . . 121-1/2” Height-Top of Hyd. Endgate w/o Hook. . . . . . . 65”. . . . . . . . . 85-1/2”. . . . . . 65”. . . . . . . . . 85-1/2” Height-Top of Screen (Vertical Beater Only). . N/A . . . . . . . . . N/A. . . . . . . . . N/A. . . . . . . . . 117” Inside Width. . . . . . . . . . . . . . . . . . . . . . . . . . 72”. . . . . . . . . 72”. . . . . . . . . 72”. . . . . . . . . 72” Inside Length. . . . . . . . . . . . . . . . . . . . . . . . . 16’. . . . . . . . . .16’. . . . . . . . . .16’. . . . . . . . . .16’ Inside Depth. . . . . . . . . . . . . . . . . . . . . . . . . . 34”. . . . . . . . . 53”. . . . . . . . . 34”. . . . . . . . . 53” Overall Width w/Tires. . . . . . . . . . . . . . . . . . . 10’2”. . . . . . . . 10’2”. . . . . . . . 10’2”. . . . . . . . 10’2” Overall Length. . . . . . . . . . . . . . . . . . . . . . . . 26’5”. . . . . . . . 26’5”. . . . . . . . 27’5”. . . . . . . . 27’5” Lower Horizontal Beater Diameter. . . . . . . . . 29”. . . . . . . . . 29”. . . . . . . . . N/A. . . . . . . . . N/A Upper Horizontal Beater Diameter. . . . . . . . . 20”. . . . . . . . . 29”. . . . . . . . . N/A. . . . . . . . . N/A Vertical Beater Diameter. . . . . . . . . . . . . . . . N/A. . . . . . . . . N/A. . . . . . . . . 34”. . . . . . . . . 34” Hydraulic Push Unload Rate @ 15 GPM. . . . 31 Sec. . . . . . 52 Sec. . . . . . 31 Sec. . . . . . 52 Sec. Hydraulic Push Cylinder Diameter. . . . . . . . . 3-1/2”. . . . . . . 4-1/2”. . . . . . . 3-1/2”. . . . . . . 4-1/2” Spindle Size. . . . . . . . . . . . . . . . . . . . . . . . . . 3”. . . . . . . . . . 3”. . . . . . . . . . 3”. . . . . . . . . . 3” Hubs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Bolt. . . . . . . 10 Bolt. . . . . . 8 Bolt. . . . . . . 10 Bolt Tire Size. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 385 x 22.5. . . 425 x 22.5. . . . 385 x 22.5. . . . 425 x 22.5 Wood Side Rails. . . . . . . . . . . . . . . . . . . . . . Standard. . . . . Standard. . . . . Standard. . . . . Standard Standard PTO. . . . . . . . . . . . . . . . . . . . . . . . 540 RPM. . . . . 1000 RPM. . . . 540 RPM. . . . . 1000 RPM Optional PTO. . . . . . . . . . . . . . . . . . . . . . . . . 1000 RPM. . . . 1-3/4” 1000. . . 1000 RPM. . . . 1-3/4” 1000 Hydraulic Endgate. . . . . . . . . . . . . . . . . . . . . Standard. . . . . Standard. . . . . Standard. . . . . Standard Semi Liquid Rear Pan. . . . . . . . . . . . . . . . . . Optional. . . . . Optional. . . . . Standard. . . . . Standard Weight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7000#. . . . . . . 9680#. . . . . . . N/A. . . . . . . . . 11,000# Approx Note: Determine right and left side of spreader by viewing it from the rear. If instructions or parts lists call for hardened bolts see page 6 to identify.

-5-

-6-

BE ALERT!

YOUR SAFETY IS INVOLVED.

THIS SYMBOL IS USED THROUGHOUT THIS BOOK WHENEVER YOUR PERSONAL SAFETY IS INVOLVED. TAKE TIME TO BE CAREFUL. REMEMBER: THE CAREFUL OPERATOR IS THE BEST OPERATOR. MOST ACCIDENTS ARE CAUSED BY HUMAN ERROR. CERTAIN PRECAUTIONS MUST BE OBSERVED TO PREVENT THE POSSIBILITY OF INJURY OR DAMAGE.

TRACTORS This operator’s manual uses the term “Tractor” when identifying the power or the towing source.

-7-

RECOGNIZE SAFETY INFORMATION This is the safety-alert symbol. When you see this symbol on your machine or in this manual, be alert to the potential for personal injury.

Follow recommended precautions and safe operating practices.

UNDERSTAND SIGNAL WORDS A signal word- DANGER, WARNING, or CAUTION - is used with the safety-alert symbol.DANGER identifies the most serious hazards.

Safety signs with signal word DANGER or WARNING are typically near specific hazards.

General precautions are listed on CAUTION safety signs.

FOLLOW SAFETY INSTRUCTIONS Carefully read all safety messages in this manual, and all safety signs on your machine. Follow all recommended precautions and safe operating procedures.

Keep signs in good condition. Immediately replace any missing or damaged signs.

OBSERVE MAXIMUM TRANSPORT SPEED The maximum transport speed for this implement is 32 km/h (20 mph).

Some tractors are capable of operating at speeds that exceed the maximum transport speed of this implement. Regardless of the maximum speed capability of the tractor being used to tow this implement, do not exceed the implement’s maximum transport speed.

Exceeding the implements maximum transport speed can result in: Loss of control of the tractor/implement combination Reduced or no ability to stop during braking Implement tire failure Damage to the implement structure or its components Use additional caution and reduce speed when towing under adverse surface conditions, when turning, and when on inclines.

Do not attempt transport if the fully loaded implement weighs more than 1.5 times the weight of the tractor.

-8-

TRACTORS This operators manual uses the term “Tractor” when identifying the power or the towing source.

WA R N IN G TO PREVENT SERIOUS INJURY OR DEATH BEFORE YOU ATTEMPT TO OPERATE THIS EQUIPMENT, READ AND STUDY THE FOLLOWING INFORMATION. IN ADDITION, MAKE SURE THAT EVERY INDIVIDUAL WHO OPERATES OR WORKS WITH THIS EQUIPMENT, WHETHER FAMILY MEMBER OR EMPLOYEE, IS FAMILIAR WITH THESE SAFETY PRECAUTIONS. KNOW HOW TO STOP UNLOADING MECHANISM BEFORE STARTING IT. If the machine becomes clogged, disengage the PTO. Stop the tractor engine, remove ignition key, and allow all mechanisms to stop before cleaning or working on the machine.

Never allow riders in or on the machine.

DO NOT get off the tractor while the spreader is in operation.

DO NOT attempt to perform maintenance or repair with tractor running and PTO and hydraulic hoses hooked up.

DO NOT step up on machine at any time.

NEVER manually feed material into the beaters.

DO NOT allow minors to operate or be near the machine.

DO NOT ALLOW PERSONNEL OTHER THAN THE QUALIFIED OPERATOR NEAR THE MACHINE. Before starting tractor, be sure PTO shields turn freely and PTO is securely locked to tractor.

DO NOT clean, adjust, or lubricate the machine when any part is in operation.

Keep hands, feet, and clothing away from beaters when they are revolving.

Loose or floppy clothing should not be worn by the operator.

Be sure the machine is clear of people, tools, and other objects before engaging PTO. DO NOT step over power take off shaft. Stay clear of PTO at all times.

NEVER start manure spreader until all guards and safety shields are secured in place.

NEVER operate spreader with a PTO speed Greater Than Recommended PTO RPM. Stay clear of Hydraulic Lines. They may be under extreme pressure or heat.

Frontier always takes the operator and his safety into consideration and guards exposed moving parts for his protection. However, some areas cannot be guarded or shielded in order to assure proper operation. In addition, the operators manual and decals on the machine itself warn you of further danger and should be read and observed closely.

Study The Above Safety Rules ATTENTION - BE ALERT - YOUR SAFETY IS INVOLVED -9-

-10-

-11-

-12-

OPERATION 1.

2.

3.

4.

5.

6.

Check for proper assembly and adjustment and make sure that all bolts are tightened. Securely retighten after a few hours of operation, as bolts can loosen up on new machinery. Check wheel bolts upon delivery and periodically thereafter. Wheel bolts should be tightened at 100 ft/lbs. of torque on MS1442H and 300 ft/lbs. of torque on MS1455H Check the tires and inflate to the recommended pressure (385/65R-22.5 and 425/65R-22.5 tires to 85 psi).

Adjust the tractor hitch and attach the spreader to the tractor as described in the following sections.

Attach hydraulic hoses to double acting valves on tractor.

Lubricate the machine completely and check the oil level of the gearbox.

Before operation, run machine slowly to make sure that the spreader is operating and lubricated properly.

TRACTOR HITCH The hitch of the spreader is designed for a standardized tractor hitch. Adjust the drawbar so that it is 13 to 17 inches above the ground. Extend or shorten it so that the horizontal distance from the end of the tractor power takeoff shaft to the center of the hitch pin hole is 14 inches for 540 PTO and 15-3/4” for 1000 PTO as shown in drawing. An improperly located hitch point may cause damage to the universal joints of the power takeoff. Secure the drawbar so that the hitch pin hole is directly below the power drive line.

If this implement is attached to a tractor with a clevis If this implement is attached to a tractor with an offset in hitch (hammer-strap) style drawbar, the hammer-strap the drawbar, be certain it is in the down position to must be removed to prevent damage to the IID guarding prevent damage to the IID guarding and the IID telescoping members. [See Figure 2] and the IID telescoping members.[See Figure 1]

ATTACHING TO THE TRACTOR 1.

2.

3.

4.

5.

6.

Fasten the spreader hitch to the drawbar with a hitch pin with a safety locking device. Use 2” diameter hitch pin to pull spreader.

Remove the weight from the jack (jack is not to be used when spreader is loaded). Remove jack from pipe mount and place on convenient storage mount located on the side of the left push frame brace.

This allows protection of jack from tractor tires during turns.

ATTENTION: Remove tractor quick coupler (If equipped). Tractor three point hitch arm should be removed or positioned so they cannot come in contact with spreader. Failure to heed will cause damage to spreader and Void Warranty.

Connect hydraulic hoses which operate the spreader hydraulic push gate from the spreader to a double acting valve on the tractor.

Connect hydraulic hoses which operate the hydraulic endgate to another double acting valve on the tractor.

Slide spring loaded locking collar on PTO yoke rearward, and slide it onto the tractor PTO shaft.

Release spring loaded collar. Be sure the pins fall into the groove of the tractor PTO shaft and collar snaps forward into locking position. CAUTION: Do not use a steel hammer to aid in joining PTO parts.

-13-

OPERATION (Continued) SERVICING Be certain to disconnect all sources of power before servicing. Keep pant cuffs and loose clothing away from all chains and drives as well as the other moving parts. Keep off the equipment when in use, and keep all shields in place. Do not attempt to clean, grease or lubricate while the machine is running.

Never allow riders in or on the machine.

When transporting on the highway, connect power cord from tractor to spreader. Make sure lights functioning properly. Regularly clean the reflective tape and SMV sign at the rear of the spreader.

LOADING In freezing weather, make certain that hydraulic tailgate is not frozen to the sides or on the floor of the spreader. Make sure the push gate is not frozen to the spreader floor or any lumps of manure are frozen to the floor.

Begin loading the spreader at the front end and work toward the rear until loading is completed. Loading this way permits the material to be spread uniformly. Loading front to rear is particularly important when the spreader is loaded by a mechanical loader because this type of load requires more power to spread than other loads.

When hauling extremely heavy materials with a large portion of dirt, it may be necessary to reduce the load size to prevent excessive shear bolt breakage. Never dump material onto the beater. Do not use extra sideboards. Do not overload spreader. Overloading decreases spreading effectiveness. Do not load more than 15 inches above the beater (Horizontal Beater).

SPREADING 1.

2.

3.

4.

5.

Engage tractor PTO slowly. Beater is always in the engaged position, therefore, engaging tractor PTO will automatically start the beaters.

Raise the hydraulic endgate by engaging the tractor hydraulics. Note: Hydraulic endgate MUST BE RAISED COMPLETELY prior to engaging hydraulic pushgate.

Engage tractor hydraulics to operate spreader push gate.

Control the speed of the spreader push gate by rotating the lever on the flow control valve (A), located on the PTO shield near the front of the spreader. If the tractor is equipped with in cab flow control, the lever on the flow control valve can be put in the full flow position and the spreader push gate can be controlled with the in cab control.

When the spreader is empty disengage the tractor PTO (which will stop the beater). Engage tractor hydraulics to return the spreader pushgate. When spreader push gate is completely retracted engage tractor hydraulics to close hydraulic endgate.

A

-14-

ADJUSTMENTS FAILURE TO FOLLOW THE RECOMMENDED ADJUSTMENTS WILL VOID WARRANTY PRIMARY & SECOND BEATER DRIVE CHAINS Both beater drive chains can be adjusted by loosening bolts (A)and sliding poly tensioners toward the chain until 1/2” of deflection can be obtained on the opposite side (B).

Retighten bolts (A) when deflection is obtained.

NOTE: PERIODICALLY LUBRICATE ALL ROLLER CHAINS WITH A LIGHT MACHINE OIL. B A B

Shields Removed for Clarity

BE SURE ALL SHIELDS ARE SECURED INTO PLACE PRIOR TO RE-STARTING MACHINE. ADJUSTING WHEEL HUBS To adjust wheel hubs, tighten the castellated nut on the spindle to the point where there is no end-play and a slight drag on the bearings. Replace the cotter key with a new one of the correct size.

SHEAR BOLT Both beaters at the rear of the spreader are protected by one shear bolt located in the PTO at the front of the spreader. Four spare shear bolts are provided. Shearing of bolts is normally due to large frozen chunks of manure, foreign objects (rocks, chunks of wood etc.) in the manure, running spreader push gate too fast when unloading long straw and pen-packed material, or STARTING SPREADER PTO TOO QUICKLY WITH HIGH TRACTOR RPM’S. Always determine the reason for shearing bolt and eliminate the problem before replacing shear bolt. Always use proper Frontier shear bolt (540 RPM HP42N98 5/16”-18 x 2” GR. 8 bolt, HPD81 5/16”-18 lock nut) or (1000 RPM HP42N97 5/16”-18 x 2” GR. 5 bolt, HP1D81 5/16”-18 lock nut.

540 RPM = 5/16x2 GR 8 1000 RPM = 5/16x2 GR 5

Shear Bolt

Spare Shear Bolts

-15-

BEATER REMOVAL BEATER REMOVAL The beater attachment can easily be removed for various reasons such as manure stock piling. Remove bolts, nuts and lockwashers (A). Remove connector link on chain (B). Strip chain from sprockets. Set bolts and chain aside. Securely attach a lifting chain to lifting eyes at the top of the beater assembly (C) on vertical beater and to the upper beater (D) on the horizontal beater. Using a proper lifting device, lift beater assembly gently until alignment pegs are clear of the alignment holes (E).

Horizontal Beater Assembly Weighs: 620 lbs.

Vertical Beater Assembly Weighs: 1940 lbs.

C

B

A Shields Removed for Clairty

D

E

E

A

A F

BEATER TIMING

BEATER STORAGE

Beaters must be timed so flighting of opposite beater is half way between the beater being timed. To time beaters, remove top shield and remove one chain coupler between the two gear cases so beater can be turned for proper timing is achieved. Reconnect chain coupler and reinstall shield.

Before the beater assembly is removed, make sure the legs (Part # HPHGV10) are securely bolted in place (F). The beater assembly must be stored on a flat level concrete surface.

CLEAN OUT PAN The clean out pan should be used at the end of each day or between each load during freezing weather.

To trip the pan pull forward on lever (G). The pan (H) will drop and allow manure build up to fall to the ground. Note: The endgate should be completely raised and the push gate fully extended (All the way to the rear of the spreader). To reset the clean out pan lift up on handle (I).

G

H

I

-16-

LUBRICATION GUIDE The operator should become familiar with all lubrication points and establish a systematic routine to ensure complete and quick lubrication of the machine.

GREASE FITTINGS There are numerous grease fittings on the spreader. If these are lubricated properly and often enough, it will prolong the life of the spreader. (Grease every 20 hours, also before and after power washing.) Make certain that the grease fittings are free of paint and dirt, force a high-quality grease into them until the grease comes out around the shaft on the sleeve-type bearings. On the sealed ball bearings, grease should be added slowly until a slight bead forms at the seals indicating the correct amount of lubricant.

Wipe off excess grease to prevent the accumulation of chaff and grit around the bearings.

GREASE ZERK LOCATION A. (3) PTO Shaft B. (2) Front Drive Shaft Bearings.

C. (1) Gear Box Output Shaft D. (4) Each Beater End E. (2) Endgate Pivot Points

F. G. H. I. J.

A F B Shields Removed for Clarity

C (Behind Shield)

H

G

E

(2) Over Running Clutch (Rear Half of PTO) (2) Each Axle Pivot (Remote Zerk) (4) Each Wheel Hub (2) Each Lower Beater Bearing (1) Gearbox Drive Shaft

H

H

E

G

H

D

D D Shields Removed for Clarity

-17-

LUBRICATION GUIDE (CONTINUED)

J

K

Shields Removed for Clairty

I

CHAIN OILER The Vertical Beater attachment is equipped with a chain oiler. The oiler will place a prescribed amount of oil to the drive chains every time the hydraulic endgate is raised. Warm weather the oiler should be filled with a #30 oil and cold weather #10 oil. The reservoir (K) is located behind the shield at the right rear of the spreader. Maintain oil level no less than 1/4 tank.

GEARBOX Before using your new machine, check the oil in the beater drive gearbox or gearboxes (Vertical Beaters).

Keep the gearbox filled to the oil plug on the side of the gearbox as shown with Mobilube SHC 75W90 (or equivilant) gear lube.

CHECK PLUG

(Gearbox is located underneath rear of spreader)

-18-

LUBRICATION GUIDE (CONTINUED) DRIVE CHAINS The drive chains are lubricated by a automatic chain oiler. This will extend the life of the drive chains. Keep chains aligned with sprockets, this will also lengthen the life of the sprockets and drive chains.

PTO ASSEMBLY- Care must be taken to keep the male and female driving elements well lubricated and free sliding. Failure to observe this precaution will result in excessive pressure being required to collapse or extend the assembly while subject to operating torque. This excessive force may damage or displace the main shaft bearings. DO NOT lubricate the shield surfaces.

The shield surfaces must be kept dry, as dirt accumulation on them will quickly cause these units to bind and not rotate. Care should also be taken to be certain that the rotating integral shields are not dented or damaged, as this also will result in excessive force being applied against the jackshaft.

Damaged shields also cause obvious difficulties when installing the assembly.

If at any time the shields do not turn freely, they should be checked to determine the cause, and repaired or cleaned. To avoid damage to the main drive bearings, avoid turning sharp corners while PTO is running. Start and Stop PTO slowly to avoid damage to the drive line.

BEATER When replacing beater paddles (Horizontal Beaters), the sharp edges of the teeth must lead in the direction of beater travel. On the right half of the beater the teeth must point to the right side of the spreader. On the left half of the beater the teeth must point to the left side of the spreader. Always use Frontier special grade 5 bolts, washers, and nuts when replacing tips. Use Frontier part number HPR10 (1/2” special bolt), HPR35 (1/2” lock washer), HPR11 (1/2” special nut), torque to 60 foot lbs.

When transporting on the highway, connect power cord from tractor to spreader. Make sure llights function properly. Regularly clean the reflective tape and SMV sign at the rear of the spreader.

-19-

DECAL LOCATION Your Frontier Manure Spreader was manufactured with operator safety in mind. Located on the manure spreader are various decals to aid in operation, and warn of danger or caution areas. Pay close attention to all decals on your Manure Spreader.

DO NOT REMOVE ANY OF THESE DECALS. IF DECALS ARE LOST, DAMAGED, OR IF MANURE SPREADER IS REPAINTED, REPLACE DECALS. REMEMBER: DECALS ARE FOR YOUR PROTECTION AND INFORMATION. Listed below are the decals on your Manure Spreader. These decals may be ordered individually by part number or by ordering a complete set.

ITEM PART NO. ITEM PART NO. DESCRIPTION A HP1442H (2) Frontier MS1442H Decals FF. HP93020 HP1455H (2) Frontier MS1455H Decals GG. HP71494A B HP2X9AMBER (6) Amber Reflector C HP1494K (1) Warning - Do Not Remove Shields HH. HP12794 D HPFRON1 Warning - Help Avoid Injury E HP9194B Danger - Never Allow Riders F HP1494L Danger - Rotating Driveline G HP9194A (5) Danger - No Step (7) Vertical Beaters H Serial Number I HP1494B Warning - Do Not Remove Shields J HP1494J (3) Warning - Do Not Clean or Work K HPFRONTIER19 (3) Frontier Decal L HP71188B Jack Storage Position M HP111593C (2) Warning - Stay Clear of Endgate N HP111593A (2) Danger - Stay Clear of Beater O HP2X9RED (2) Red Reflectors P HP11599 (3) Warning - Stay Clear of Leaks Q HP82602 (2) Warning - Crushing Hazard R 5HPHS404 Patent Number S. HP32597A Warning - Do Not Operate T. HP1906C (2) Warning - Stay Clear U. HP1906D (2) Danger - Stay Clear V. HP12306 Shear Bolt W. HP1906E (2) Warning - Stay Clear X. HP1906F Danger - Keep Out (3) MS1442H (5) MS1455H Y. HP123002 (2) Warning - Stay Clear of Endgate Z. HP93366 Keep Operators Manual Here AA. HP51606 Warning - Do Not Operate BB. HP71706 Attention - Tractor 3pt Hitch CC. HP3494A (2) Remote Grease Fitting DD. HP1494A (2) Warning - Do Not Operate EE. HP92606 Warning - Do Not Exceed Transport Speed 5HP720061442 Complete Set of Decals for MS1442H 5HP720061455 Complete Set of Decals for MS1455H E W K P X W J

DESCRIPTION (2) Grease Fitting (2) Warning - Do Not Remove Shields (2) Warning - Do Not Operate

D A

BB T

Y

G

X

V

CC (Behind Tire)

Q AA H EE P (Behind Shield)

G G L U

-20-

R B

K

DECAL LOCATION (CONTINUED)

A

Y

M

B K

J

E

B

W K

N

P

U

O

G

DD

P G

Q

T

Z DD S Shields Removed for Clarity HH (Behind Shield) GG N

N

J

C C G

O

N

J

C

I

M

Y

-21-

FF

FF

TROUBLE SHOOTING WARNING MAKE SURE THAT THE TRACTOR IS SHUT OFF AND THE SPREADER CAN NOT MOVE BEFORE SERVICING THE MANURE SPREADER. MAINTENANCE AND REPAIR SERVICE WORK TO BE PERFORMED BY A QUALIFIED SERVICE PERSON ONLY.

TROUBLE...

POSSIBLE CAUSE...

POSSIBLE REMEDY...

Beater Will Not Run

Tractor PTO Not Turning

Engage Tractor PTO

PTO Shaft Shear Bolt Sheared

Replace PTO Shaft Shear Bolt (See Page #15)

Primary Beater Drive Chain Off, Broken or Missing

Replace or Repair Primary Beater Drive Chain (See Page #15)

Key Sheared or Missing on Beater Drive or Driven Sprocket

Replace Sheared or Missing Key

Top Beater Does Not Turn

Secondary Beater Drive Chain Off, Broken or Missing

Replace or Repair Secondary Beater Drive Chain (See Page #15)

Push Gate Will Not Move

Tractor Hydraulics Not Engaged

Engage Tractor Hydraulics

Flow Control Valve Turned Off

Reset Flow Control Valve (See Page #14)

Low Tractor Hydraulic Flow or Pressure

Have Servicing Dealer Check Tractor Flow And Pressure

Hydraulic Couplers Not Coupled To Tractor Properly

Couple Hoses To Tractor (See Page #13)

Spreader Is Over Loaded

Reduce Load

OPTIONAL EQUIPMENT REAR PAN The rear pan shown below is optional equipment on the MS1442H & MS1455H spreader. The rear pan option allows for a even spread when light applications are needed.

When transporting on the highway, connect power cord from tractor to spreader. Make sure lights function properly. Regularly clean the reflective tape and SMV sign at the rear of the spreader.

-22-

INSTRUCTIONS FOR ORDERING PARTS All service parts should be ordered through your authorized Frontier dealer. He will be able to give you faster service if you will provide them with the following: 1. Model & Serial Number - Both can be located on the side of the front center bearing post above the jack mount.

2. All references to left or right apply to the machine as viewed from the rear.

3. Parts should not be ordered from illustration only. Please order complete part number.

4. If your dealer has to order parts - give shipping instructions: VIA truck - large pieces (please specify local truck lines) VIA United Parcel Service (include full address)

PLEASE RECORD NUMBERS FOR YOUR UNIT FOR QUICK REFERENCE

ABOUT IMPROVEMENTS FRONTIER IS CONTINUALLY STRIVING TO IMPROVE IT’S PRODUCTS We must therefore, reserve the right to make improvements or changes whenever it becomes practical to do so, without incurring any obligation to make changes or additions to the equipment previously sold.

-23-

35

FIGURE 1

-24-

FIGURE 1 FRONTIER MODEL MS1442H & MS1455H FRAME ASSEMBLY ITEM MS1442H MS1455H 1.

HP27N14 “ 2.

HP12N13 “ 3.

HP12N12 “ 4.

HP16SV329 “ 5.

HP42N1 “ 6.

HPX97 “ 7.

HP16SV327 “ 8.

HP42N2 “ 9.

HP42N3 “ 10.

HP12N14 “ 11.

HP42N4 “ 12.

HP42N5 HP55N1 13.

HP42N43 “ * “ 14.

HP16SV89 * HP60N15 * HP42N138 * HP16SV88 15.

HPBFR405 * HP16SV77 16.

HP45N35 HP16SV214 17.

HP9S17 “ 18.

HP45N57 “ 19.

HPS47 “ 20.

HP42N41 “ 21.

HP16V9 “ 22.

HP45N36 HP16SV75 23.

HP42N6 HP55N2 24.

HP42N7 HP55N3 25.

HP31N4 “ 26.

HP33SV40 HP66N15 27.

HP33SV45 HP60N8 28.

HP33SV42 HP60N5 29.

HP33SV43 HP60N7 30.

HP33SV44 HP60N6 31.

HPRG169 HP60N10 32.

HPRG170 HP60N9 33.

HP33SV95 HP60N2 34.

HPRG17 HP60N3 35.

HP33SV46 HP60N4 36.

HPRG171 HP60N11 37.

HP33SV41 HP60N13 38.

HPRG72 HP60N14 39.

HP42N8 HP55N4 * HP42N9 HP55N5 40.

HP42N10 “ * HP42N11 “ 41.

HP42N12 “ 42.

HPF97 “ 43.

HP42N97 “ * HP42N98 44.

HPD81 “ NOTE: * (MEANS NOT SHOWN) - (MEANS NOT USED ON THIS MODEL) “ (MEANS SAME AS PREVIOUS PART NO.)

-25-

DESCRIPTION Jack Jack Pin & Chain Jack Handle PTO Shield Shield Mount Hair Pin PTO Shield Bottom PTO Holder Spring Jack Mount Wood Rail Front Panel SMV Bracket SMV Sign Wheel 13.5 x 22.5 (8 Bolt) Wheel 13.5 x 22.5 (10 Bolt) Tire (385 x 22.5 Truck) Tire (425 x 22.5 Truck) 1/2” x 5-1/2” Bolt GR. 5 1/2” x 6” Bolt GR. 5 Collar For Axle 1/2” Lock Nut Grease Line Adapter Grease Fitting Grease Line Grease Bracket Bushing For Tandem Axle Tandem Axle Left Tandem Axle Right Roll Pin Spindle Hub Seal Inner Bearing Inner Race Outer Race Outer Bearing Washer Spindle Nut Cotter Pin Hub Cap Stud Lug Nut Side Poly Right Side Poly Left Floor Poly Right Floor Poly Left Poly Side Angle SMV Holder 5/16” x 2” Shear Bolt GR.5 (1000 RPM) 5/16” x 2” Shear Bolt GR. 8 (540 RPM) Lock Nut

FIGURE 2

-26-

FIGURE 2 FRONTIER MODEL MS1442H & MS1455H BEATER DRIVE TRAIN ITEM MS1442H MS1455H 1.

HP42N13 “ 2.

HP42N14 “ 3.

HP42N15 “ 4.

HPS138 “ 5.

HP12V62 “ 6.

HP42N16 “ 7.

HP16SV379 “ 8.

HP12V67 “ 9.

HP42N17 “ 10.

HP42N18 “ 11.

HP42N19 “ 12.

HP42N137 “ 13.

HP42N20 “ 14.

HP42N21 “ 15.

HP42N22 “ 16.

HP42N23 “ 17.

HP42N24 “ 18.

HP42N25 “ 19.

HPPB136 “ 20.

HP42N26 “ 21.

HPG83 “ 22.

HP42N27 “ 23.

HP12V104 “ 24.

HP42N49 “ 25.

HP42N99 “ 26.

HP42N100 “ 27.

HP42N101 “ 28.

HP42N102 “ NOTE: “ (MEANS SAME AS PREVIOUS PART NO.) - (MEANS NOT USED ON THIS MODEL)

-27-

DESCRIPTION Input Shaft Shield Input Shield Angle Input Shield Back 3/8” x 2-3/8” Key Snap Ring Input PVC Shield 3/8” x 2-1/2” Roll Pin Bearing Input Shaft Bearing Drive Shaft Center PVC Shield Bearing Saddle Drive Shaft Middle PVC Shield Drive Shaft Back PVC Shield Cross Shaft Cross Shaft PVC Shield Sprocket 50-B-20 1-1/2” Bore Sprocket 50-B-20 1-3/4” Bore 3/8” x 2” Key Gearbox Set Screw Connector Chain #50 x 20 Pitches 20 T Sprocket Gearbox Gusset 3/8” U-Bolt Bearing Hose Holder 5/16” x 2” ID U-Bolt

FIGURE 3

-28-

FIGURE 3 FRONTIER MODEL MS1442H & MS1455H ENDGATE & BEATER ITEM MS1442H MS1455H 1.

HP42N28 HP55N9 2.

HP42N29 HP55N10 3.

HP42N30 HP55N11 4.

HP42N31 HP55N12 5.

HP42N32 HP55N13 6.

HP42N33 HP55N14 7.

HP42N34 HP55N15 8.

HP42N35 HP55N16 9.

HP42N36 “ 10.

HP42N37 “ 11.

HP42N38 “ 12.

HP56N69 “ 13.

HP42N39 “ 14.

HP42N40 “ 15.

HP23N277 “ 16.

HPR11 “ 17.

HPR35 “ 18.

HPR10 “ 19.

HPS436 * HPPB136 20.

HP42N42 HP42N38 21.

HP45N27 HP23N277 22.

HP45N43 * HP42N36 * HP42N37 23.

HPG83 “ 24.

HP42N44 * HP16SV213 25.

HP42N45 * HP55N17 26.

HPF157 HPD39 27.

HP42N46 * HP55N19 * HP42N47 28.

HP16SV34 * HP42N48 “ 29.

HP55N18 30.

HP16SV72 “ 31.

HP42N50 “ 32.

HP42N51 “ 33.

HP42N52 HP55N20 34.

HP42N53 35.

HP42N54 HP55N21 36.

HP42N55 HP55N22 37.

HP42N56 “ 38.

HPF69 “ 39.

HPF56 “ 40.

HP42N103 “ 41.

HP42N104 42.

HPX193 “ 43.

HPX192 “ 44.

HPX195 “ 45.

HP42N105 “ 46.

HPX194 “ 47.

HP42N141 “ 48.

HPS414 “ 49.

HPS415 “ 50.

HPS416 “ 51.

HPS418 “ 52.

HP42N142 53.

HPF157 “ NOTE: * (MEANS NOT SHOWN) - (MEANS NOT USED ON THIS MODEL) “ (MEANS SAME AS PREVIOUS PART NO.)

DESCRIPTION Endgate Hinge Pin Endgate Poly Holdown Endgate Rubber Right Endgate Rubber Left Endgate Rubber Endgate Poly Beater Panel Blade Holder Right Blade Holder Left Beater Beater Stub Shaft Beater Drive Shaft Beater Slot Filler Beater Blade 1/2” Lock Nut Lock Washer 1/2” x 1-1/4” Beater Blade Bolt GR. 5 3/8” x 1-1/2” Key 3/8” x 2” Key Second Beater Second Beater Blade Blade Holder Blade Holder Right Blade Holder Left 3/8” Set Screw Second Beater Sprocket 60-B-30 Second Beater Sprocket 80-B-23 Second Beater Chain #60 x 98 Pitches Second Beater Chain #80 x 82 Pitches Connector Link Beater Sprocket #80, 20T To #60, 25T (540 RPM) Beater Sprocket #80, 36T To #80, 20T (1000 RPM) Beater Sprocket #80, 36T To #60, 25T (1000 RPM) Beater Chain #80 x 79 Pitches (540 RPM) Beater Chain #80 x 88 Pitches (1000 RPM) Second Beater Slot Filler Pillow Block Bearing Poly Chain Tightener Tightener Stop Main Panel Right End Second Beater Anti-Wrap Rear Shield Shield Filler Cross Shaft Shield Shield Bracket Clip Pin Beater Spacer Second Beater Shield Latch Catch Bracket Latch (Rubber) Pin Back Stake Filler Latch Mounting Bracket 3/8” x 2-1/4” Key Cap Manual Holder Tube Manual Holder Clamp Cap w/Hole Stub Shaft Shield #80 Connector Link

-29-

38

38

FIGURE 4

-30-

FIGURE 4 FRONTIER MODEL MS1442H & MS1455H HYDRAULICS ITEM MS1442H MS1455H 1.

HPDWM205 “ 2.

HP12SV25 * HP55N82 3.

HPBFR74 “ 4.

HP46N40 “ 5.

HPBFR287 “ 6.

HPHE59 “ 7.

HP42N59 HP55N23 8.

HP42N60 HP55N24 9.

HP12V19 “ 10.

HP45N45 “ 11.

HP56N141 “ 12.

HP23N108 “ 13.

HP42N61 * HP55N6 14.

HP42N62 * HP55N7 15.

HPJB82 16.

HP23N116 * HPLW96 17.

HP42N63 * HP55N8 18.

HP23N234 * HPHE58 19.

HP16SV351 “ 20.

HP16SV339 “ 21.

HPWM146 * HPDF8 22.

HP42N64 “ 23.

HP42N65 * HP55N29 24.

HP42N66 * HP55N30 25.

HP42N67 * HP55N65 26.

HPDWM110 * HPHE58 27.

HP42N68 * HP16SV143 28.

HP42N69 * HP55N32 29.

HP42N70 * HP55N33 30.

HP42N71 HP55N34 31.

HP42N72 HP55N35 32.

HP12V70 * HP55N66 33.

HP42N73 “ 34.

HPJB82 35.

HP16SV351 36.

HPDWM233 * HP55N70 37.

HP23N116 * HPWM139 38.

HPT144 “ NOTE: * (MEANS NOT SHOWN) - (MEANS NOT USED ON THIS MODEL) “ (MEANS SAME AS PREVIOUS PART NO.)

-31-

DESCRIPTION Quick Coupler Male Hydraulic Hose 3/8” x 145” (1/2”MPX x 3/8”MPX) Hydraulic Hose 3/8’’ x 155” (1/2”MP x 3/8”MP) 3/8” Tee Hydraulic Hose 3/8” x 46” (3/8”MPX x 3/8”MP) Hydraulic Hose 3/8” x 36” (3/8”MPX x 3/8”MP) 3/8” Elbow End Gate Hydraulic Line Short End Gate Hydraulic Line Long Hydraulic Hose 3/8” x 24” (3/8”FP x 3/8”MPX) Hydraulic Cylinder (2’’ x 20”) Cylinder Pin 7/32” x 2” Cotter Pin Hydraulic Hose 3/8” x 93” (1/2”MP x 1/2”MP) Hydraulic Hose 1/2” x 93” (1/2”MP x 1/2”MP) Hydraulic Hose 3/8” x 95” (3/8”MP x 1/2”MP) Hydraulic Hose 1/2” x 95” (1/2”MP x 1/2”MP) 1/2” x 3/8” Bushing 3/8’’ Service Tee 1/2” Service Tee Hydraulic Hose 3/8” x 82” (3/8”MPX x 3/8”MPX 90°) Hydraulic Hose 1/2” x 82” (1/2”MPX x 1/2”MPX 90°) 3/8” Street Elbow 1/2” Street Elbow 3/8” Nipple Nut Sequence Valve 3/8” Male, Female Tee 1/2” Tee Hose Shield (1-1/2”ID x 73”) Hydraulic Hose 3/8” x 158” (3/8”MPX 90° x 3/8”MPX) Hydraulic Hose 1/2” x 158” (1/2”MPX 90° x 1/2”MPX) Hydraulic Hose 3/8” x 76” (3/8”MP x 3/8”MP) Hydraulic Hose 1/2” x 76” (1/2”MP x 1/2”MP) 3/8” Union Adapter 45° 1/2” Union Adapter 45° 3/8” Union Adapter 90° 1/2” Street Elbow Hydraulic Hose 3/8” x 20-1/2” (3/8”MP x 3/8”MPX 90°) Hydraulic Hose 1/2” x 19” (1/2”MP x 1/2”MPX) Hydraulic Cylinder 3-1/2” x 90” Gimbal Mount Hydraulic Cylinder 4-1/2” x 90” Gimbal Mount Hydraulic Cylinder 3-1/2” x 90” Trunnion Mount Hydraulic Cylinder 4-1/2” x 90” Trunnion Mount Cylinder Pin Pusher Cylinder Pin Hose Clamp SAE#88 Hose Clamp SAE#104 Flow Control 1/2” To 3/8” Bushing 3/8” Nipple Nut 3/8” Union Adapter 1/2” Union Adapter 3/8” Service Tee 1/2” Male-Female Tee Cylinder Clip Pin

FIGURE 5

FIGURE 5 FRONTIER MODEL MS1442H & MS1455H HYDRAULIC END GATE CYLINDER

ITEM MS1442H MS1455H 1.

HP23N142A “ 2.

HP23N143A “ 3.

HP23N144 “ 4.

HP45N42 “ 5.

HP45N43 “ 6.

HP45N44 “ 7.

HP23N148 “ 8.

HP23N149 “ 9.

HP23N150A “ 10.

HP23N151 “ 11 HP45N45 “ NOTE: “ (MEANS SAME AS PREVIOUS PART NO.)

-32-

DESCRIPTION Clevis Cap Rod Cap Piston Rod Cylinder Tube Tie Rod Piston Nut Plug Rod Clevis Seal Kit Hydraulic Cylinder

FIGURE 6

FIGURE 6 FRONTIER MODEL MS1442H & MS1455H HYDRAULIC PUSHER CYLINDER ITEM MS1442H MS1455H DESCRIPTION 1.

HP42N106 HP55N36 Internal Head 2.

HP42N107 HP55N37 Barrel Assembly (Top Cylinder) * HP42N108 HP55N38 Barrel Assembly (Bottom Cylinder) 3.

HP42N109 HP55N39 Piston 4.

HP42N110 HP55N40 Lock Nut 5.

HP42N111 HP55N41 Spacer 6.

HP42N112 HP55N42 Rod 7.

HP42N113 HP55N43 Seal Kit 7A. “ “ Wear Ring 7B. “ “ Poly Hone 7C. “ “ O-Ring 7D. “ “ O-Ring 7E. “ “ O-Ring 7F. “ “ Back-up Ring 7G. “ “ Wear Ring 7H. “ “ Loaded U-Cup 7J. “ “ Rod Wiper * HP42N69 HP55N32 Complete Cylinder (Top) * HP42N70 HP55N33 Complete Cylinder (Bottom) NOTE: * (MEANS NOT SHOWN) “ (PART NOT SOLD SEPARATELY ONLY COMPLETE KIT)

-33-

FIGURE 7

-34-

FIGURE 7 FRONTIER MODEL MS1442H & MS1455H PUSHER

ITEM MS1442H MS1455H 1.

HP42N74 HP55N44 2.

HP42N75 HP55N45 3.

HP42N76 HP55N46 4.

HP42N77 HP55N47 5.

HP42N78 HP55N48 6.

HP42N79 HP55N49 7.

HP3G21 * HPF73 8.

HP42N80 HP55N50 9.

HP42N81 HP55N81 10.

HP42N82 HP55N25 11.

HP42N83 HP55N26 12.

HP42N84 HP55N51 13.

HP42N114 14.

HP50N183 “ 15.

HP42N85 HP55N52 16.

HP42N86 HP55N53 17.

HP42N87 HP55N54 18.

HP42N88 HP55N55 19.

HP42N89 HP55N56 20.

HP42N90 HP55N57 21.

HPA7 * HP55N58 22.

HP42N91 HP55N59 23.

HP42N92 HP55N27 * HP42N93 HP55N28 24.

HP42N94 “ 25.

HP42N95 “ 26.

HP42N96 “ 27.

HP42N139 HP55N83 28.

HP42N140 HP16SV379 NOTE: * (MEANS NOT SHOWN) - (MEANS NOT USED ON THIS MODEL)

-35-

DESCRIPTION Moveable Floor Tube Pusher Tubing Slide Pusher Tube Front Guide Cylinder Retainer End Cap Clamp Right End Cap Clamp Left 1” Snap Ring 1-1/4” Snap Ring Rear Cylinder Pin Pusher Wiper Pusher Rubber Strap Pusher Cylinder Shield Pusher Shim (As Required) 5/8” x 1-1/4” Bolt GR. 5 Poly Block Spacer Pusher Poly Slide Poly Block Spacer Right Pusher Poly Slide Right Pusher Poly Slide Left Poly Block Spacer Left 1/2” x 9-1/2” Bolt GR. 5 1/2” x 10-1/2” Bolt GR. 5 Pusher Spacer Pusher Rubber Left Pusher Rubber Right Pusher Extension Extension Wing Right Extension Wing Left Pusher Bottom Rubber 3/8” Expansion Pin

FIGURE 8

-36-

FIGURE 8 FRONTIER MODEL MS1442H & MS1455H BEATER GEAR BOX

ITEM MS1442H MS1455H 1.

HPG125 “ 2.

HPG138 “ 3.

HPG126 “ 4.

HPG144 “ 5.

HPG140 “ 6.

HPG65 “ 7.

HPG56 “ 8.

HPG145 “ 9.

HPG130 “ 10.

HPG128 “ 11.

HPG129 “ 12.

HPG132 “ 13.

HPG142 “ 14.

HPG136 “ 15.

HP42N57 “ 16.

HPG61 “ 17.

HPG133 “ 18.

HPG137 “ 19.

HP42N58 “ 20.

HPG139 “ 21.

HPG127 “ * HP42N26 “ NOTE * (MEANS NOT SHOWN) - (MEANS SAME AS PREVIOUS PART NO.)

-37-

DESCRIPTION Housing Gasket Cover 3/8” Vent Plug Cap 3/8” Plug - NPT 5/16” x 5/8” Cap Screw 3/8” Plug Snap Ring Bearing Cup #25520 Bearing #25581 Stake Nut Bevel Gear 22 Teeth Seal - Output Output Shaft “E” 1210 Woodruff Key Stake Nut Seal - Input Input Shaft 3/8” x 1-1/2” Hardened Key Bevel Gear 33 Teeth Complete Gear Box

FIGURE 9

-38-

FIGURE 9 FRONTIER MODEL MS1442H & MS1455H VERTICAL BEATERS FRAME ASSEMBLY ITEM MS1442H MS1455H DESCRIPTION 1.

HPHGV54 HPHGV55 Frame 2.

HPHGV3 HPHGV4 Rear Shield 3.

HPHGV5 HPHGV6 Shield Filler 4.

HPHGV7 “ Cross Shaft Shield 5.

HPHGV8 “ Beater Bottom Mount 6.

HPHGV9 “ Pan Hinge 7.

HPHGV10 “ Leg 8.

HPHGV11 “ Pan Bottom 9.

HPHGV12 “ Pan 10.

HPK103 “ Spring 11.

HPHGV13 “ Pan Handle 12.

HPHGV14 “ Pan Handle Stop 13.

HPHGV56 “ Gearbox Bottom Shield 14.

HPHGV57 “ Gearbox Top Shield 15.

HPHGV17 “ Chain Damper 16.

HPS416 “ Manual Holder Clamp 17.

HPS414 “ Cap 18.

HPS415 “ Manual Holder Tube 19.

HPS418 “ Cap w/Hole 20.

HPHGV18 “ Sprocket Idler Shaft 21.

HP12V62 “ Snap Ring 22.

HPF69 “ Shield Bracket 23.

HPF56 “ Clip Pin 24.

HP42N105 “ Back Stake Filler 25.

HPX195 “ Pin 26.

HPX194 “ Latch Mounting Bracket 27.

HPX192 “ Latch (Rubber) 28.

HPX193 “ Latch Catch Bracket 29.

HPHGV48 “ 5/16” x 1-1/2” Step Bolt 30.

HPHGV49 “ Stone Guard 31.

HPHGV50 “ Lifting Eye 32.

HPHGV51 “ Grease Line 33.

HPHGV52 “ Grease Fitting 34.

HPHGV53 “ Chain Damper Top 35.

HP16SV64 “ 3/4” Flange Nut 36.

HP16SV44 “ Tightener Spacer 37.

HPHE8 “ 3/4” x 2-1/4” Bolt GR.5 38.

HPHGV103 Main Panel Brace Left 39.

HPHGV104 Main Panel Brace Right 40.

HPHGV108 “ Latch Pivot Bolt (3/4” X 3-1/2” Carriage NOTE: “ (MEANS SAME AS PREVIOUS MODEL) Bolt Gr. 5) * (MEANS NOT SHOWN)

-39-

FIGURE 10

-40-

FIGURE 10 FRONTIER MODEL MS1442H & MS1455H VERTICAL BEATERS DRIVE TRAIN ITEM MS1442H MS1455H 1.

HPHGV19 HPHGV20 2.

HPHGV21 HPHGV22 * HPHGV102 “ 3.

HPHGV23 “ 4.

HPHGV24 “ 5.

HPHGV27 “ 6.

HPB5 “ 7.

HPB5A “ 8.

HP3G18 “ 9.

HP3G7 “ 10.

HPBFR63 “ 11.

HPBFR64 “ 12.

HPBFR65 “ 13.

HP17G144 “ 14.

HPS38 “ 15.

HPHGV58 “ 16.

HPHGV29 “ 17.

HP42N25 “ 18.

HP42N27 “ * HPD118 “ 19.

HPHGV59 “ 20.

HPHGV60 “ 21.

HPHGV61 “ 22.

HPHGV41 “ 23.

HPHGV25 “ 24.

HPHGV34 * HPHGV35 * HPF157 “ 25.

HP12V52 “ 26.

HP12V77 “ 27.

HPBFR374 “ 28.

HPHGV36 “ 29.

HP42N100 “ 30.

HPHGV37 * HPHGV38 31.

HPHGV39 * HPHGV40 * HPF157 “ 32.

HPHGV46 “ 33.

HP10R14 “ 34.

HPHGV30 “ 35.

HPHGV43 “ 36.

HPHGV42 “ 37.

HP56N160 “ 38.

HPST36 “ NOTE: * (MEANS NOT SHOWN) “ (MEANS SAME AS PREVIOUS MODEL) - (MEANS NOT USED ON THIS MODEL)

-41-

DESCRIPTION Beater Left Hand Beater Right Hand Beater Stub Shaft Beater Blade Left Beater Blade Right Seal Bearing Cone Bearing Cup Bearing Cup Bearing Cone Washer Nut Cotter Pin Hub Cap 3/8” x 2-3/8” Square Key Gearbox Left Gearbox Connector Sprocket 50-B-20 1-3/4” Bore Connector Chain #50 x 20 Pitches Connector Link #50 Gearbox Cross Shaft Gearbox Right Gearbox Drive Shaft Bearing Sprocket 80-B-20 1-3/4” Bore Gearbox Chain #80 x 136 Pitches Gearbox Chain #80 x 97 Pitches Connector Link #80 Bearing Idler Sprocket w/Bearing (80-A-12) I-Bolt 3/8” x 3” Beater Tightener Bearing Sprocket 80-A-36 to 80-A-20 Sprocket 80-A-20 to 80-A-20 Drive Chain #80 x 117 Pitches Drive Chain #80 x 109 Pitches Connector Link #80 I-Bolt 5/16” x 1” Spring Spacer Spacer Tightener Spring Holder Spring

FIGURE 12

FIGURE 12 FRONTIER MODEL MS1442H & MS1455H VERTICAL BEATERS LEFT HAND GEARBOX ITEM HP425VB HP550VB 1.

HPHGV88 “ 2.

HPHGV89 “ 3.

HPHGV90 “ 4.

HPHGV105 “ 5.

HPHGV91 “ 6.

HPHGV92 “ 7.

HPHGV93 “ 8.

HP23N288 “ 9.

HPHGV95 “ 10.

HPHGV96 “ 11.

HP17G58 “ 12.

HPJB82 “ 13.

HPHGV99 “ 14.

HPHGV94 “ 15.

HPHGV97 “ 16.

HPHGV112 “ 17.

HPHGV98 “ * HPHGV58 “ NOTE: *(MEANS NOT SHOWN) “ (MEANS SAME AS PREVIOUS MODEL) -42-

DESCRIPTION Bottom Housing Top Housing Output Shaft Input Shaft Bearing Cone Bearing Cup Output Shaft 3/8” Nipple Plug (1/2-14 NPT) Gearbox Bolt Vent Bushing (1/2”NPT To 3/8”NPT) Cap Bearing Cone Bearing Cone Bearing Cup Retaining Ring Complete Gearbox Left

FIGURE 13

FIGURE 13 FRONTIER MODEL MS1442H & MS1455H VERTICAL BEATERS RIGHT HAND GEARBOX ITEM HP425VB HP550VB 1.

HPHGV88 “ 2.

HPHGV89 “ 3.

HPHGV90 “ 4.

HPHGV101 “ 5.

HPHGV91 “ 6.

HPHGV92 “ 7.

HPHGV93 “ 8.

HP23N288 “ 9.

HPHGV95 “ 10.

HPHGV96 “ 11.

HP17G58 “ 12.

HPJB82 “ 13.

HPHGV94 “ 14.

HPHGV97 “ 15.

HPHGV112 “ 16.

HPHGV98 “ * HPHGV60 NOTE: * (MEANS NOT SHOWN) “ (MEANS SAME AS PREVIOUS MODEL) -43-

DESCRIPTION Bottom Housing Top Housing Output Shaft Input Shaft Bearing Cone Bearing Cup Seal 3/8” Nipple Plug (12 -14 NPT) Gearbox Bolt Vent Bushing (1/2” NPT To 3/8”NPT) Bearing Cone Bearing Cone Bearing Cup Retaining Ring Complete Gearbox Right

FIGURE 14

FIGURE 14 FRONTIER MODEL MS1442H & MS1455H PTO & OVERRUNNING CLUTCH

ITEM 540 RPM 1000 RPM 1-3/8” 1000 RPM 1-3/4” 1.

HP16SV274 “ HP16SV275 2.

HP42N115 HP55N68 HP55N69 3.

HP16SV179 “ “ 4.

HP42N116 “ “ 5.

HP16SV181 “ “ 6.

HP16SV283 “ “ 7.

HP42N117 “ “ 8.

HP42N118 “ “ 9.

HP16SV286 “ “ 10.

HP42N119 “ “ 11.

HP42N120 “ “ 12.

HP16SV193 “ “ 13.

HP42N98 * HP42N97 “ * HP42N122 HP55N72 HP55N73 * HP42N123 HP55N74 HP55N75 * HP42N124 HP55N76 “ * HP42N125 HP55N77 “ * HP42N126 HP55N78 HP55N79 * HPS204 “ “ NOTE: * (MEANS NOT SHOWN) - (MEANS NOT USED ON THIS MODEL) “ (MEANS SAME AS PREVIOUS PART NO.)

-44-

DESCRIPTION Auto-Lock Repair Kit Auto-Lock Yoke Assembly 35R Cross Bearing Kit Yoke Shaft Nylon Repair Kit Safety Sign Outer Guard Inner Guard Safety Sign Yoke, Tube & Slip Sleeve OR Ball Shear Assembly 5/16”-18 Lock Nut 5/16”-18 x 2” Bolt GR. 8 (540 RPM) 5/16”-18 x 2” Bolt GR. 5 (1000 RPM) Joint & Shaft Half Assembly w/Guard Joint & Shaft Half Assembly Joint & Tube Half Assembly w/Guard Joint & Tube Half Assembly Complete PTO PTO Safety Manual

FIGURE 15

FIGURE 15 FRONTIER MODEL MS1442H & MS1455H LIGHTING

ITEM MS1442H MS1455H 1.

HPS310 “ 2.

HPS309 “ 3.

HPS308 “ 4.

HP56N155 “ 5.

HPS441 “ 6.

HP56N154 “ 7.

HPFBO-TLPC “ 8.

HP55N60 “ 9.

HP55N61 “ 10.

HP55N62 “ 11.

HP55N63 “ 12.

HP55N64 “ 13.

HPBFR666 “ 14.

HP55N80 “ NOTE: “ (MEANS SAME AS PREVIOUS PART NO.)

-45-

DESCRIPTION Red Tail Light Yellow Hazard Light Rubber Light Mount Tail Light Harness Light Module Flasher Module Harness Tractor Cord Light Bracket Mount Left Light Bracket Left Light Bracket Right Light Plug Bracket Metal Cushioned Cable Clamps Extension Light Harness Light Bracket Mount Right

FIGURE 16

FIGURE 16 FRONTIER MODEL MS1442H & MS1455H CHAIN OILER ITEM PART# DESCRIPTION 1.

HPHGV63 Reservoir 2.

HPHGV64 Hydraulic Hose 1/4” x 80” 3.

HPHGV65 O-Ring/JIC Elbow 4.

HPHGV66 Filler Hose 5.

HPHGV67 Brush 6.

HPHGV68 Pump Mount Bracket 7.

HPHGV69 Brush Bracket 8.

HPHGV70 Bracket Mount 9.

HPHGV71 Oiler Tube 5/32” (50’) 10.

HPHGV72 Small Tube Holder 11.

HPHGV73 3/16” x 3/8” Tap Tight 12.

HPHGV74 2” Hose Clamp 13.

HPHGV75 1” Hose Clamp * HPHGV76 Medium Tube Holder NOTE: * (MEANS NOT SHOWN)

ITEM 14. * 15.

16.

17.

18.

19.

20.

21. * 22.

23.

24.

25. *

-46-

PART# HPHGV77 HPHGV78 HPHGV79 HPHGV80 HPHGV81 HPST33 HPBFR120 HPWM146 HPHGV82 HPHGV83 HPHGV84 HPHGV85 HPHGV86 HPHGV87 HPHGV62

DESCRIPTION Edging 12” Large Tube Holder 9/16” x 2-1/2” Bolt GR. 5 9/16” Lockwasher 9/16” Nut Angle 3/8” Union Adapter Male-Female Pipe Tee Complete Pump Pump Repair Kit Manifold Assembly (Complete) Sleeve Nut Standoff Ferrule Complete Oiler Kit

FIGURE 17

FIGURE 17 FRONTIER MODEL MS1442H & MS1455H OPTIONAL REAR PAN ITEM MS1442H MS1455H 1.

HP42N127 “ 2.

HPR70 “ 3.

HP42N128 “ 4.

HP42N129 “ 5.

HP42N130 “ 6.

HP42N131 “ 7.

HPHE7 “ 8.

HPF69 “ 9.

HPST36 “ 10.

HPT73 “ 11.

HP42N132 “ 12.

HP42N133 “ 13.

HP42N134 “ 14.

HP42N135 “ 15.

HP23N212 “ 16.

HP23N213 “ 17.

HP42N136 “ 18.

HPBFR295 “ 19.

HP56N170 “ NOTE: “ (MEANS SAME AS PREVIOUS PART NO.)

-47-

DESCRIPTION Pan 3/16” x 2” Cotter Pin Pan Plate Left Pan Plate Right Pan Strap Rubber 3/4” Lock Nut Bracket Spring Washer Latch Bushing Latch Latch Spacer 3/4” x 2-1/2” Carriage Bolt GR. 5 3/8” Long Nut 3/8” x 1” I-Bolt Rope (18’) Snap Hook Pan Washer

SERVICE / MAINTENANCE RECORD DATE

DESCRIPTION

NOTES

-48-