Frontier Manure Spreader MS1231 MS1237 MS1243 Operator's Manual(5HPOMSP5) - PDF DOWNLOAD

OPE RATOR ’ S

MANUAL

MANURE SPREADER MS1231 MS1237 MS1243

HSMFG812011 Rev.4

5HPOMSP5

TABLE OF CONTENTS TABLE OF CONTENTS..............................................................INSIDE COVER WARRANTY & NOTES.............................................................................................................................1 DEALER PRE-DELIVERY & DELIVERY CHECKLIST........................................3 SP E C IF I C ATI O N S. . . . .. . . .. . . .. . . .. . . .. . . . .. . . .. . . .. . . .. . . .. . . . .. . . .. . . .. . . .. . . . .. . . .. . . .. . . .. . . .. . . 5 BOLT TORQUE CHART................................................................................................6 BE ALERT SYMBOL......................................................................................................7 SAFETY RULES........................................................................................................8-9 DANGER - WARNING DECALS..............................................................................10-11 OPERATION MS1231, MS1237 & MS1243............................................................12-13 ADJUSTMENTS........................................................................................................14-16 LUBRICATION GUIDE MS1231, MS1237 & MS1243..........................................16-18 TROUBLE SHOOTING............................................................................................................................19 OPTIONAL EQUIPMENT..................................................................................................................20-21 DECAL LOCATION...........................................................................................................................22-23 ORDERING PARTS - ABOUT IMPROVEMENTS..........................................................24 SERVICE & PARTS NOTES......................................................................................25 PARTS LISTS & DIAGRAMS MS1231, MS1237 & MS1243...................................26-49 OPTIONAL DOUBLE CYLINDER (MS1231 ONLY)............................................................................39 OPTIONAL HYDRAULIC DRIVE......................................................................................................41 OPTIONAL PAN..........................................................................................................27 OPTIONAL TOP BEATER..............................................................................................48 OPTIONAL ELECTRIC CONTROLS.................................................................................49 SERVICE RECORDS.................................................................................................50

WARRANTY: Warranty coverage is provided by John Deere according to the terms of the Agricultural/Commercial & Consumer Equipment Warranty Statement. Carefully read the warranty statement on the back of your original purchase order for details on coverage and limitations of this warranty.

NOTES

-1-

AFTER COMPLETION, DEALER SHOULD REMOVE AND RETAIN FOR RECORDS FRONTIER DEALER PRE-DELIVERY CHECK LIST After the Manure Spreader has been completely set-up, check to be certain it is in correct running order before delivering to the customer. The following is a list of points to inspect. Check off each item as you have made the proper adjustments and found the item operating satisfactorily.

PTO shields turn freely.

All Shields and Guards are in place and fastened.

All grease fittings have been lubricated and gearbox filled to proper level See lubrication guide in this manual.

All mechanisms are operating trouble free.

All roller chains are at proper tension.

All bolts and fasteners are tight.

All decals are in place and legible.

(Dealer’s Name)

Model Number Serial Number

(Signature of Pre-Delivery Inspector)

(Inspection Date)

DEALER DELIVERY CHECK LIST This check list that follows is an important reminder of valuable information that should be passed on to the customer at the time this Manure Spreader is delivered.

Check off each item as you explain it to the customer.

This delivery check list, when properly filled out and signed assures the customer that the Pre-delivery service was satisfactorily performed.

Explain to the customer that the pre-delivery inspection was made.

Explain to the customer all the safety precautions they must excercise when operating this unit.

Explain recommended loads for different types of materials.

Explain to customer that regular lubrication is required for proper operation and long life of machine. Show customer the lubrication section of Owner’s Manual.

Give the customer Owner’s Manual and make sure he reads and understands all operating and service instructions.

Record Serial Number on page 24 of this Manual.

Date Delivered

Dealer’s Name By Signature of Original Buyer

-3-

FRONTIER MODEL MS1231, MS1237 & MS1243 MANURE SPREADER Your Frontier spreader has been manufactured of the finest quality materials and components. The performance you get from your machine is largely dependent upon how well you read and understand this manual and apply this knowledge. There is a right and a wrong way to do everything. Please do not assume that you know how to operate and maintain your spreader before reading this manual carefully. Keep this manual available for ready reference.

S P E C I F I C AT I O N S MS1231 MS1237 MS1243 Top Flare Width. . . . . . . . . . . . . . . . . . . . . . . . . . . . 68’. . . . . . . . . . . . . . . 68”. . . . . . . . . . . . . . . . . . .68” Inside Width. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59-3/4”. . . . . . . . . . . .59-3/4”. . . . . . . . . . . .59-3/4” Inside Length. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15’7”. . . . . . . . . . . . . .16’6”. . . . . . . . . . . . . . . 16’6” Inside Depth. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28-3/8”. . . . . . . . . . . . 34-3/8”. . . . . . . . . . . .40-3/8” Overall Width w/295/75R22.5 Tires. . . . . . . . . . . . 97”. . . . . . . . . . . . . . . 97”. . . . . . . . . . . . . . . . . .N/A Overall Width w/16.5 x 16.1 Tires. . . . . . . . . . . . . . 107”. . . . . . . . . . . . . . 107”. . . . . . . . . . . . . . . . 107” Overall Length. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21’-11-1/2”. . . . . . . . .23’-2-1/2”. . . . . . . 23’-2-1/2” Overall Loading Height (Top of Flare). . . . . . . . . . 51-1/2”. . . . . . . . . . . . 57-1/2”. . . . . . . . . . . .63-1/2” Overall Height w/Hyd. Endgate. . . . . . . . . . . . . . . . 55”. . . . . . . . . . . . . . . 61”. . . . . . . . . . . . . . . . . . 67” Diameter of Beater. . . . . . . . . . . . . . . . . . . . . . . . . .29”. . . . . . . . . . . . . . . 29”. . . . . . . . . . . . . . . . . . 29” Weight w/295/75R22.5 Tires. . . . . . . . . . . . . . . . . 4190 Lbs. . . . . . . . . .4920 Lbs . . . . . . . . . . . .N/A Weight w/16.5 x 16.1 Tires. . . . . . . . . . . . . . . . . . . 4200 Lbs. . . . . . . . . . 4930 Lbs. . . . . . . .5220 Lbs Capacity (Old Rating). . . . . . . . . . . . . . . . . . . . . . . .310 Bu. . . . . . . . . . . .370 Bu . . . . . . . . . . .430 Bu. Capacity - Cu. Ft. Struck Level. . . . . . . . . . . . . . . . 185. . . . . . . . . . . . . . .235. . . . . . . . . . . . . . . . . 275 Rear Hydraulic Endgate. . . . . . . . . . . . . . . . . . . . . Standard . . . . . . . . . .Standard . . . . . . . .Standard Semi Liquid Rear Pan. . . . . . . . . . . . . . . . . . . . . . . Optional . . . . . . . . . . Optional . . . . . . . . . Optional Upper Beater. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Optional. . . . . . . . . . . Optional . . . . . . . . . Optional Drive. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Two Speed Clutch to Worm Gear All Models Worm Gear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Bronze . . . . . . . . . . . .Bronze . . . . . . . . . . . Bronze Variable Speed Hydraulic Drive. . . . . . . . . . . . . . . Optional . . . . . . . . . . .Optional . . . . . . . . .Optional Front Splash Panel. . . . . . . . . . . . . . . . . . . . . . . . . .Sandard. . . . . . . . . . .Standard . . . . . . . .Standard PTO Speed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 540 RPM. . . . . . . . . .540 RPM . . . . . . . 540 RPM Note: Determine right and left side of spreader by viewing it from the rear. If instructions or parts lists call for hardened bolts see page 6 to identify.

-5-

-6-

BE ALERT!

YOUR SAFETY IS INVOLVED.

THIS SYMBOL IS USED THROUGHOUT THIS BOOK WHENEVER YOUR PERSONAL SAFETY IS INVOLVED. TAKE TIME TO BE CAREFUL. REMEMBER: THE CAREFUL OPERATOR IS THE BEST OPERATOR. MOST ACCIDENTS ARE CAUSED BY HUMAN ERROR. CERTAIN PRECAUTIONS MUST BE OBSERVED TO PREVENT THE POSSIBILITY OF INJURY OR DAMAGE. TRACTORS This operator’s manual uses the term “Tractor” when identifying the power or the towing source.

-7-

RECOGNIZE SAFETY INFORMATION This is the safety-alert symbol. When you see this symbol on your machine or in this manual, be alert to the potential for personal injury.

Follow recommended precautions and safe operating practices.

UNDERSTAND SIGNAL WORDS A signal word- DANGER, WARNING, or CAUTION - is used with the safety-alert symbol.DANGER identifies the most serious hazards.

Safety signs with signal word DANGER or WARNING are typically near specific hazards.

General precautions are listed on CAUTION safety signs.

FOLLOW SAFETY INSTRUCTIONS Carefully read all safety messages in this manual, and all safety signs on your machine. Follow all recommended precautions and safe operating procedures.

Keep signs in good condition. Immediately replace any missing or damaged signs.

OBSERVE MAXIMUM TRANSPORT SPEED The maximum transport speed for this implement is 32 km/h (20 mph).

Some tractors are capable of operating at speeds that exceed the maximum transport speed of this implement. Regardless of the maximum speed capability of the tractor being used to tow this implement, do not exceed the implement’s maximum transport speed.

Exceeding the implements maximum transport speed can result in: � Loss of control of the tractor/implement combination � Reduced or no ability to stop during braking �Implement tire failure � Damage to the implement structure or its components Use additional caution and reduce speed when towing under adverse surface conditions, when turning, and when on inclines.

Do not attempt transport if the fully loaded implement weighs more than 1.5 times the weight of the tractor.

-8-

TRACTORS

This operators manual uses the term “Tractor” when identifying the power or the towing source.

WA R N IN G TO PREVENT SERIOUS INJURY OR DEATH BEFORE YOU ATTEMPT TO OPERATE THIS EQUIPMENT, READ AND STUDY THE FOLLOWING INFORMATION. IN ADDITION, MAKE SURE THAT EVERY INDIVIDUAL WHO OPERATES OR WORKS WITH THIS EQUIPMENT, WHETHER FAMILY MEMBER OR EMPLOYEE, IS FAMILIAR WITH THESE SAFTEY PRECAUTIONS. KNOW HOW TO STOP UNLOADING MECHANISM BEFORE STARTING IT. If the machine becomes clogged, disengage the PTO. Stop the tractor engine, remove ignition key, and allow all mechanisms to stop before cleaning or working on the machine.

Never allow riders in or on the machine.

DO NOT get off the tractor while the spreader is in operation.

DO NOT attempt to perform maintenance or repair with tractor running and PTO hooked up.

DO NOT step up on machine at any time.

NEVER manually feed material into the beaters.

DO NOT allow minors to operate or be near the machine.

DO NOT ALLOW PERSONNEL OTHER THAN THE QUALIFIED OPERATOR NEAR THE MACHINE. Before starting tractor, be sure PTO shields turn freely and PTO is securely locked to tractor.

DO NOT clean, adjust, or lubricate the machine when any part is in operation.

Keep hands, feet, and clothing away from beaters when they are revolving.

Loose or floppy clothing should not be worn by the operator.

Be sure the machine is clear of people, tools, and other objects before engaging PTO. DO NOT step over power take off shaft. Stay clear of PTO at all times.

NEVER start manure spreader until all guards and safety shields are secured in place.

NEVER operate spreader with a PTO speed Greater Than 540 RPM. Stay clear of Hydraulic Lines. They may be under extreme pressure or heat.

Frontier always takes the operator and his safety into consideration and guards exposed moving parts for his protection. However, some areas cannot be guarded or shielded in order to assure proper operation. In addition, the operators manual and decals on the machine itself warn you of further danger and should be read and observed closely.

Study The Above Safety Rules ATTENTION - BE ALERT - YOUR SAFETY IS INVOLVED -9-

DECALS

-10-

DECALS

-11-

1.

2.

3.

4.

5.

6.

OPERATION

Check for proper assembly and adjustment and make sure that all bolts are tightened. Securely retighten after a few hours of operation, as bolts can loosen up on new machinery. Check wheel bolts upon delivery and periodically thereafter. Wheel bolts should be tightened at 85-90 ft/lbs. of torque.

Check the tires and inflate to the recommended pressure(295/75R22.5 tires to 55 pounds 16.5 x 16.1 tires to 36 pounds).

Adjust the tractor hitch and attach the spreader to the tractor as described in the following sections.

Attach the speed control/beater engage and disengage rope to a convenient point on the tractor.

Lubricate the machine completely and check the oil level of both gearboxs.

Before operation, run machine slowly to make sure that the spreader is operating and lubricated properly.

TRACTOR HITCH

The hitch of the spreader is designed for a standardized tractor hitch. Adjust the drawbar so that it is 13 to 17 inches above the ground. Extend or shorten it so that the horizontal distance from the end of the tractor power takeoff shaft to the center of the hitch pin hole is 14 inches, as shown in drawing. An improperly located hitch point may cause damage to the universal joints of the power takeoff. Secure the drawbar so that the hitch pin hole is directly below the power drive line.

If this implement is attached to a tractor with a clevis If this implement is attached to a tractor with an offset in

hitch (hammer-strap) style drawbar, the hammer-strap the drawbar, be certain it is in the down position to must be removed to prevent damage to the IID guarding prevent damage to the IID guarding and the IID telescoping members. [See Figure 2] and the IID telescoping members.[See Figure 1]

ATTACHING TO THE TRACTOR

1.

2.

3.

Fasten the spreader hitch to the drawbar with a hitch pin with a safety locking device. Use 1” diameter hitch pin to pull spreader.

Remove the weight from the jack (jack is not to be used when spreader is loaded). Remove jack from pipe mount and place on convenient storage mount located on top of left hitch channel. This allows protection of jack from tractor tires during turns.

Slide spring loaded locking collar on PTO yoke rearward, and slide it onto the tractor PTO shaft Release spring loaded collar. Be sure the pins fall into the groove of the tractor PTO shaft and collar snaps forward into locking position. CAUTION: Do not use a steel hammer to aid in joining PTO parts.

SERVICING

Be certain to disconnect all sources of power before servicing. Keep pant cuffs and loose clothing away from all chains and drives as well as the other moving parts. Keep off the equipment when is use, and keep all shields in place. Do not attempt to clean, grease or lubricate while the machine is running.

Never allow riders in or on the machine.

When transporting on the highway, regularly clean the reflective tape at the rear of the spreader.

There is a holder provided for your SMV sign.

-12-

LOADING

In freezing weather, make certain that hydraulic tailgate is not frozen to the sides or on the floor of the spreader. Make sure the apron chain is not frozen to the spreader floor or any lumps of manure are frozen to the floor.

Begin loading the spreader at the front end and work toward the rear until loading is completed. Loading this way permits the material to be spread uniformly. Loading front to rear is particularly important when the spreader is loaded by a mechanical loader because this type of load requires more power to spread than others loads.

When hauling extremely heavy materials with a large portion of dirt, it may be necessary to reduce the load size to prevent excessive shear bolt breakage. Never dump material onto the beater. Do not use extra sideboards. Do not overload spreader. Overloading decreases spreading effectiveness. Do not load more than 15 inches above the beater.

SPREADING

NOTE: Two speed drive mechanism and beater engage/disengage are controlleed be one rope leading to the tractor.

1.

When ready to unload, make sure beater is in the engaged position and low speed indicator is visible through low speed hole in panel of spreader.

2.

Raise the hydraulic endgate.

3.

Engage the tractor PTO shaft slowly.

4.

Increased apron speed, if desired, can be accomplished by steadily pulling on the rope until it stops. Speed select indicator should now be visible through the high speed hole. Beater will continue to operate and apron speed will be increased.

5.

When the spreader is almost empty, the bed can be cleaned by shifting into clean out position.

Apply a steady pull on the rope until it stops and speed indicator is visible in the clean out hole. In this position, the beater will stop and the apron will continue to operate at the same speed as in high speed position, thus saving unnecessary driving.

6.

When spreader is empty, shut off tractor PTO. Pull control rope until speed select indicator snaps into low speed. This will re-engage beater for the next load. DO NOT SHIFT FROM CLEAN OUT TO LOW SPEED WITH THE TRACTOR PTO RUNNING. 7.

Do not operate the spreader with a PTO speed greater than 540 RPM’s unless necessary sprocket changes have been made.

Low Speed

High Speed

Clean Out

SPREADING (IF EQUIPPED WITH OPTIONAL HYDRAULIC DRIVE)

1.

2.

3.

4.

5.

Engage tractor PTO shaft slowly. Beater is always in the engaged position, therefore, engaging tractor PTO will automatically start beater.

Raise the hydraulic tailgate.

Open hydraulic valve on tractor connected to speed control valve on spreader.

Control speed of apron by turning speed control handle clockwise to increase speed, counterclockwise to decrease speed.

When spreader is almost empty, the bed can be cleaned out by disengaging tractor PTO (which will stop beater), and increasing apron speed by turning control handle clockwise, thus saving unnecessary driving time.

-13-

ADJUSTMENTS FAILURE TO FOLLOW THE RECOMMENDED ADJUSTMENTS WILL VOID WARRANTY APRON 1.

Adjust the apron by loosening the mounting bolts on the chain slides on the outside of the frame.

Mounting bolts shown in the drawing.

2. Tighten the adjusting bolts until the apron chain clears the under side of the axle by 1 inch.

NOTE: Tighten the adjusting bolts (on each front corner) equally on each side so that the apron slats run parallel with the ends of the bed. The apron will be damaged if the machine is operated with one end of the apron slats running ahead of the opposite end. Do not tighten the apron chains excessively.

MOUNTING BOLTS

ADJUSTING BOLT

DRIVE CHAIN

To adjust front drive chain, turn nut on adjusting rod (located at the right hand front side of spreader) clockwise. There should be 1/2” deflection at the center of the drive chain. Over tightening or too loose of a chain will result in excessive wear on the bearing, chain and sprockets.

TIGHTENER BOLT

ADJUSTING WHEEL HUBS

To adjust wheel hubs, tighten the castellated nut on the spindle to the point where there is no end-play and a slight drag on the bearings. Replace the cotter key with a new one of the correct size.

APRON WORM DRIVE CHAIN

The apron worm drive chains are kept tight with a spring type tightener that does not require adjustment.

However, periodic inspection should be made to check for wear.

SHEAR BOLTS (Apron drive)

The worm gearbox and apron are protected by two shear bolts.

One on the driven high speed sprocket (A) and one on the low speed sprocket (B). Two spare shear bolts are provided (C).

Shearing of these bolts is normally due to the apron being frozen fast to the floor, or catching on frozen “chunks”. Occasionally the shear bolts will shear due to the spreader being overloaded. Always determine the cause of failure, and eliminate the cause before replacing the shear bolt, using Frontier part number HP23N223.

NOTE: Normal apron speeds at 540 RPM are: low speed 4-1/2 fpm, high speed and clean out position 8-1/2 fpm. If the apron is not moving at these speeds, especially in high or clean out, check and replace the high speed shear bolt (A). Failure to do so will result in serious damage to the sprocket and shaft.

A SHEAR BOLTS B REPLACEMENT SHEAR BOLTS C

-14-

Shields Removed for Clarity

ADJUSTMENTS SHEAR BOLTS (Main Drive)

The beater and the apron drive are protected by one shear bolt located on the front end of the side drive shaft (left side of spreader).

Two spare shear bolts are provided. Shearing of the bolts is normally due to foreign objects in the manure or starting the spreader PTO too quickly with high tractor RPM’s. Always use Frontier shear bolts, part number HPD31, when replacing shear bolts.

SHEAR BOLT

Shields Removed for Clarity

SPARE SHEAR BOLTS

APRON SPEED AND BEATER CONTROL

One cable controls both the beater clutch and two speed clutch. To compensate for wear or stretching of this cable, adjust the turnbuckle behind shield at the front of the spreader.

TWO SPEED CLUTCH

If clutch control yoke becomes worn, it may be necessary to adjust the high speed clutch so it engages and disengages completely. Adjustment to compensate for this wear is made by sliding spring stop (A) on control rod closer to the clutch engaging lever. Initial adjustment should be made as follows: Distance (B) between spring stop and jam nut is seven (7”) inches. Distance (C) between jam nut and shifting rod bracket is one-eighth (1/8”) inches. This distance may be achieved by adjusting the turnbuckle at front of spreader.

-15-

Turnbuckle Shields Removed for Clarity

BEATER CLUTCH ADJUSTMENT

It may be necessary to compensate for wear in the beater clutch and clutch control yoke. When properly adjusted the moveable jaw clutch should have one-quarter (1/4”) inch (distance C) between clutches when disengaged. To adjust, loosen jam nut (A) holding spring bracket. With beater disengaged (clean out position), tighten nut (B) against shifter lever bracket until the proper distance between clutch jaws is reached. Overtightening will cause beater not to fully engage and cause excess tension on cable. Tighten lock nut (D) so there is one thirty-second (1/32”) inch clearence betweeen clutch jaws (E).

LUBRICATION GUIDE

The operator should become familiar with all lubrication points and establish a systematic routine to insure complete and quick lubrication of the machine.

GEARBOX- Before using your new machine, check the oil in the main apron drive and beater drive gearbox.

Keep the gearbox filled to the oil plug on the side of the gearbox as shown with Mobilube SHC 75W90 (or equivilant) gear lube.

DRIVE CHAINS- Lubricate the drive chains with a light machine oil. Keep chains aligned with sprockets, this will lengthen the life of the sprockets and chain. Lubricate chains often.

OIL LEVEL

OIL LEVEL

-16-

LUBRICATION GUIDE GREASE FITTINGS

There are numerous grease fittings on the spreader. If these are lubricated properly and often enough, it will prolong the life of the spreader. (Grease every 20 hours, also before and after power washing.) Make certain that the grease fittings are free of paint and dirt, force a high-quality grease into them until the grease comes out around the shaft on the sleeve-type bearings. On the sealed ball bearings, grease should be added slowly until a slight bead forms at the seals indicating the correct amount of lubricant.

Wipe off excess grease to prevent the accumulation of chaff and grit around the bearings. .

GREASE ZERK LOCATION

A. (3) PTO Shaft B. (2) Front jack shaft bearings.

C. (2) Drive Shaft D. (1) Beater E. (2) Worm Drive Gearbox F. (4) Side Shaft (Model MS1237 & MS1243) G. (3) Side Shaft (Model MS1231)

H. I. J. K. L. M. N.

(2) Tailgate Arms (2) Axle Pivot (Model MS1231 Only) (4) Axle Pivot (Model MS1237 & MS1243 Only) (1) Beater Clutch Control Yoke (1) Two Speed Clutch Control Yoke (1)Two Speed Clutch Throwout (1) Rear Support Bearing

NOTE: Shields removed in some pictures for clarity. DO NOT OPERATE WITH SHIELDS REMOVED M

L

N

K

Shields Removed for Clarity

E

A

B

H

F-G Shields Removed for Clarity

I-J

C

-17-

D

LUBRICATION GUIDE

PTO ASSEMBLY- Care must be taken to keep the male and female driving elements well lubricated and free sliding.

Failure to observe this precaution will result in excessive pressure being required to collapse or extend the assembly while subject to operating torque. This excessive force may damage or displace the jackshaft bearings. DO NOT lubricate the shield surfaces. The shield surfaces must be kept dry, as dirt accumulation on them will quickly cause these units to bind and not rotate. Care should also be taken to be certain that the rotating integral shields are not dented or damaged, as this also will result in excessive force being applied against the jackshaft. Damaged shields also cause obvious difficulties when installing the assembly. If at any time the shields do not turn freely, they should be checked to determine the cause, and repaired or cleaned. To avoid damage to the main drive bearings, avoid turning sharp corners while PTO is running.

Start and Stop PTO slowly to avoid damage to the drive line.

BEATER When replacing beater paddles, the sharp edges of the teeth must lead in the direction of beater travel. On the right half of the beater the teeth must point to the right side of the spreader. On the left half of the beater the teeth must point to the left side of the spreader. Always use Frontier special grade 5 bolts, washers, and nuts when replacing tips. Use Frontier part number HPR10 (1/2” special bolt), HPR35 (1/2” lock washer), HPR11 (1/2” special nut), torque to 60 foot lbs.

When transporting on the highway, regulary clean the reflective tape at the rear of the spreader There is a holder provided for your SMV sign.

-18-

TROUBLE SHOOTING WARNING MAKE SURE THAT THE TRACTOR IS SHUT OFF AND THE SPREADER CAN NOT MOVE BEFORE SERVICING THE MANURE SPREADER. MAINTENANCE AND REPAIR SERVICE WORK TO BE PERFORMED BY A QUALIFIED SERVICE PERSON ONLY.

TROUBLE...

POSSIBLE CAUSE...

POSSIBLE REMEDY...

Beater Does Not Turn

PTO Not Turning

Engage Tractor PTO

Beater Not Engaged

Engage Beater (See page #15)

Main Drive Shear Bolt Sheared

Replace Main Drive Shear Bolt (See page #14)

Beater Will Not Disengage

Front Drive Chain Off,

Replace or Repair Front Drive Chain

Broken, or Missing

(See page #14)

Control Cable out of Adjustment

Adjust Control Cable (See page #15)

Splined Beater Insert Worn or

Replace Splined Beater Insert and

Splines Sheared Off

Gearbox Output Shaft

Control Cable Out of Adjustment

Adjust Control Cable (See page #15)

Control Linkage Binding

Check Control Linkage, Make Sure It Is Free Moving

Apron Does Not Turn

PTO Not Turning

Engage Tractor PTO

Main Drive Shear Bolt Sheared

Replace Main Drive Shear Bolt (See page #14)

Apron Only Drives In Low

Apron only Drives in High

Front Drive Chain Off, Broken,

Replace or Repair Front Drive Chain

or Missing

(See page #14)

High Speed Shear Bolt

Replace Sheared or Missing

Sheared or Missing

Shear Bolt (See Page # 14)

Low Speed Shear Bolt

Replace Sheared or Missing

Sheared or Missing

Shear Bolt (See Page #14)

Dog or Dog Spring Worn,

Replace Worn, Broken or Missing

Broken or Missing

Dog or Dog Spring

Shear Plate Worn

Replace Shear Plate

-19-

OPTIONAL EQUIPMENT

DOUBLE CYLINDER

Frontier Model MS1231 manure spreader is equipped with brackets to accept an optional second cylinder to raise and lower the hydraulic endgate. Optional cylinder is located on right hand side of spreader.

Optional kit includes cylinder, brace, hoses, and connectors to attach to existing cylinder.

NOTE: DOUBLE CYLINDER FOR HYDRAULIC ENDGATE IS STANDARD EQUIPMENT FOR MODELS MS1237 & MS1243 HYDRAULIC DRIVE

An optional hydraulic drive unit is available to convert Models MS1231, MS1237 and MS1243 from two speed to variable speed hydraulic drive. Hydraulic drive may be used as a two or four hose tractor hook-up.

Front Control Panel

Hydraulic Motor Shields Removed for Clarity

-20-

OPTIONAL EQUIPMENT REAR PAN/SEMI-LIQUID HYDRAULIC ENDGATE

The rear pan shown below is optional equipment on Models MS1231, MS1237 & MS1243. Semi-liquid hydraulic endgate (pictured below right) is standard equipment on Models MS1231, MS1237 & MS1243. Rear pan and hydraulic endgate may be used together on all three Models.

REAR PAN

HYDRAULIC ENDGATE

TOP BEATER

UPPER BEATER

Optional upper beater available on all three models will provide more uniform spreading in heaped and heavily matted material. Upper beater may be used with hydraulic endgate.

When transporting on the highway, regularly clean the reflective tape at the rear of the spreader.

There is a holder provided for your SMV sign.

-21-

DECAL LOCATION

Your Frontier Manure Spreader was manufactured with operator safety in mind. Located on the manure spreader are various decals to aid in operation, and warn of danger or caution areas. Pay close attention to all decals on your Manure Spreader.

DO NOT REMOVE ANY OF THESE DECALS. IF DECALS ARE LOST, DAMAGED,OR IF MANURE SPREADER IS REPAINTED, REPLACE DECALS. REMEMBER: DECALS ARE FOR YOUR PROTECTION AND INFORMATION. Listed below are the decals on your Manure Spreader. These decals may be ordered individually by part number or by ordering a complete set.

ITEM PART NO. DESCRIPTION A HP1231 (2) Frontier MS1231 Model Decal HP1237 (2) Frontier MS1237 Model Decal HP1243 (2) Frontier MS1243 Model Decal B HP2X9AMBER Amber Reflector (1) MS1231 (5) MS1237 & MS1243 C HP1494K (2) Warning - Do Not Remove Shields D HPFRON1 Warning - Help Avoid Injury E HP9194B Danger - Never Allow Riders F HP1494L Danger - Rotating Driveline G HP9194A (2) Danger - No Step H Serial Number I HP1494B (2) Warning - Do Not Remove Shields J HP71188H Beater/Apron Control K HP1494J (2) Warning - Do Not Clean or Work L HPFRONTIER19 (3) Frontier Decal M HP1494A (3) Warning - Do Not Operate N HP11211176 (2) Shear Bolts O HP71188B Jack Storage Position P HP111593C (2) Warning - Stay Clear of Endgate Q HP111593A (2) Danger - Stay Clear of Beater R HP12794 (3) Warning - Do Not Remove Shields S HP093020 (2) Grease (MS1237 & MS1243 Only) T HP2X9RED (2) Red Reflectors U HP71494A (3) Warning Do Not Operate V HP11599 Warning - Stay Clear of Leaks W HP3494A (2) Remote Grease - Axle Pivot X HP82602 Warning - Crushing Hazard Y HPHS404 Patent Number Z HP92606 WARNING - Do Not Exceed Transport Speed 5HP729031231 Complete Set of Decals for MS1231 5HP729031237 Complete Set of Decals for MS1237 5HP729031243 Complete Set of Decals for MS1243 Y L K V E D C

N (Behind Shield) I

L

A

F

H U

X Z G

-22-

O

J

I

B

DECAL LOCATION B

R

P

B

U (Behind Shield)

S

U (Behind Shield) R

W

K C Q

T

M

G

U X G O Shields Removed for Clarity

P

Q

T

B

N

M Shields Removed for Clarity

-23-

INSTRUCTIONS FOR ORDERING PARTS All service parts should be ordered through your authorized Frontier dealer.He will be able to give you faster service if you will provide them with the following: 1. Model & Serial Number - Both can be located on the front center bearing post below the PTO shaft.

2. All references to left or right apply to the machine as viewed from the rear.

3. Parts should not be ordered from illustration only. Please order complete part number.

4. If your dealer has to order parts - give shipping instructions: VIA truck - large pieces (please specify local truck lines) VIA United Parcel Service (include full address)

PLEASE RECORD NUMBERS FOR YOUR UNIT FOR QUICK REFERENCE

ABOUT IMPROVEMENTS FRONTIER IS CONTINUALLY STRIVING TO IMPROVE IT’S PRODUCTS We must therfore, reserve the right to make improvements or changes whenever it becomes practical to do so, without incurring any obligation to make changes or additions to the equipment previously sold.

-24-

SERVICE AND PARTS NOTES

-25-

FIGURE 1

-26-

FIGURE 1 FRONTIER MODELS MS1231, MS1237 & MS1243 BEATER AND PAN ASSEMBLY ITEM MS1231 MS1237 MS1243 1.

5HPYBHH10130 “ “ 2.

5HP23N2 “ “ 3.

5HP23N3 “ “ 4.

5HP23N4 “ “ 5.

5HP23N276 “ “ 6.

5HP23N277 “ “ 7.

5HP23N7 “ “ 8.

5HP23N8 “ “ 9.

5HPYBHH16045 “ “ 10.

5HPYWLO16005 “ “ 11.

5HPYNTL16005 “ “ 12.

5HP23N9 “ “ 13.

5HP5B9 “ “ 14.

5HP23N10 “ “ 15.

5HP23N11 “ “ 16.

5HPF116 “ “ 17.

5HPF115 “ “ 18.

5HPF114A “ “ 19.

5HPF16 “ “ 20.

5HP23N12 “ “ 21.

5HP23N13 5HP37N1 5HP37N1 22.

5HP23N14 5HP37N2 5HP37N2 23.

5HP23N175 5HP37N50 5HP37N50 24.

5HP23N16 5HP37N4 5HP37N4 25.

5HP23N17 “ “ 26.

5HP37N78 “ “ 27.

5HP23N19 “ “ 28.

5HP31N1 5HP37N5 5HP37N5 29.

5HPR31 “ “ 30.

5HP23N21 “ “ 31.

5HPR27 “ “ 32.

5HPYBCR16010 “ “ 33.

5HP23N23 “ “ 34.

5HPYWFL16005 “ “ 35.

5HPYPCT06020 “ “ 36.

5HPF112 “ “ 37.

5HP23N24 “ “ 38.

5HP23N25 “ “ 39.

5HP23N26 “ “ 40.

5HP23N27 “ “ 41.

5HP23N28 “ “ 42.

5HP23N29 “ “ 43.

5HP23N30 “ “ NOTE: “ (SAME PART NO. AS MODEL MS1231)

-27-

DESCRIPTION 5/16” x 5” GR.5 Bolt Splined Beater Insert Beater Blade Holder LH Beater Blade Holder RH Beater Blade - Hardened Beater Blade - Hardened Beater Blade Wiper LH Beater Blade Wiper RH 1/2” x 1-1/4” Bolt GR.5 1/2” Lock Washer 1/2” Lock Nut Beater 3/8” x 1-1/4” Woodruff Key Beater Shaft Support Beater Stub Shaft Bearing Flange (Heavy Duty) Bearing (Grease Type) Bearing Flange w/Zerk 45° Lock Collar Bearing Flange Guard RH Side Poly Hold Down LH Side Poly Hold Down LH Main Panel RH Main Panel Drive Shaft Bushing Drive Shaft Bracket LH Drive Shaft Bracket RH Pan Trip Rope Clip Pan Trip Lever Spring 1/2” x 1-1/2” Carriage Bolt Trip Lever Spacer 1/2” Flat Washer Cotter Pin Spacer Pan Rubber Flap Pan Strap Pan Brace Angle Pan Support Brace LH Pan Support RH Pan Support Pan

FIGURE 2

-28-

FIGURE 2 FRONTIER MODELS MS1231, MS1237 & MS1243 SPINDLE, HUB AND BOX PARTS ITEM 1.

2.

3.

4.

5.

6.

7.

7A. 7B. 8.

9.

10.

11.

12.

13.

14.

Not Shown 15.

16.

17.

18.

19.

20.

21.

22.

23.

24.

25.

26.

27.

28.

29.

30.

31.

32.

33.

34.

35.

38.

39.

40.

41.

42.

43.

44.

45.

46.

Not Shown Not Shown Not Shown Not Shown Not Shown

MS1231 5HP23N31 5HP23N32 5HPB8 5HPB7 5HPB7A 5HPB6 5HPB32 5HPB5A 5HPB5 5HPB4 5HPB31 5HPB3 5HPB2 5HP31N2 5HP31N48 5HPYPEX16020 5HP31N5 5HP31N6 5HPYNTL16005 5HPB60 5HPYBHH16155 5HPB58 5HP23N34 5HPF33 5HPYBPU08005 5HP23N35 5HP23N36 5HP23N176 5HP23N270 5HP23N40 5HP23N41 5HP23N42 5HP23N43 5HP31N24 5HP31N25 5HP31N49 5HP31N31 5HP31N32 5HPS47 5HP31N43 5HP16V9 5HP12V36 5HP23N54 5HP23N179A 5HPMSO8C 5HP31N26

MS1237 5HP37N6 5HP37N7 5HPB90 5HPB91 5HPB91A 5HP26G4A 5HPYBSD20010 5HPYNWL20005 5HPB94A 5HPB94 “ “ “ “ 5HP37N8 5HP16SV203 “ 5HP37N10 5HP37N11 “ “ “ “ “ “ “ 5HP37N12 5HP37N13 “ 5HP37N65 “ “ “ “ 5HP37N16 5HP37N17 5HP37N81 5HP37N67 5HP37N68 5HP37N51 5HPB111 “ “ “ “ “ “ “ 5HP37N52

NOTE: “ (SAME PART NO. AS MODEL MS1231) * (SAME PART NO. AS MODEL MS1237)

-29-

MS1243 DESCRIPTION 5HP37N6 RH Side Stake 5HP37N7 LH Side Stake 5HPB90 Seal 5HPB91 Inner Bearing 5HPB91A Inner Race 5HP26G4A Hub Hub Bolt * Stud Bolt 5/8” * Lug Nut 5/8” 5HPB94A Outer Race 5HPB94 Outer Bearing “ Washer “ Cotter Pin “ Nut “ Hub Cap 5HP16SV203 Spindle 5HP16SV203 Spindle for 16.1 x 14 Wheel “ Roll Pin 1/2” x 4” 5HP37N10 Tandem Beam LH 5HP37N11 Tandem Beam RH “ 1/2” Lock Nut “ Ring “ 1/2” x 5” Bolt GR.5 “ Bushing for Tandem Axle “ Front Flare “ Rope Guide “ U-Bolt 5HP37N12 RH Gate Angle 5HP37N13 LH Gate Angle “ Front Flare Support 5HP43N1 Side Extension LH 5HP37N65 Front Gate Plywood with Poly “ Strap for Rubber “ Front Gate Rubber “ Splash Guard Side LH “ Splash Guard Side RH 5HP43N3 RH Side Flare 5HP43N4 LH Side Flare 5HP43N2 Side Extension RH 5HP37N81 Poly Floor 5HP37N67 RH Side Plywood with Poly 5HP37N68 LH Side Plywood with Poly 5HP37N51 Front Panel 5HPB111 Outer Bushing for Tandem Axle “ Grease Line Fitting “ Grease Line “ Grease Line Bracket “ Wheel 16.1 x 14 (STD. MS1243) “ Tire 16.5 x 16.1 (STD. MS1243) Wheel 22.5 x 8.25 Tire 295/75R22.5 5HP37N52 Complete Frame - (PART IS NOT USED ON THIS MODEL)

FIGURE 3

-30-

FIGURE 3 FRONTIER MODELS MS1231, MS1237 & MS1243 FRONT SHIELDS AND DRIVE ASSEMBLY ITEM 1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

11.

12.

13.

14.

15.

16.

17.

18.

20.

21.

22.

23.

24. * 25.

26.

27.

28.

29.

30.

31.

32.

33.

34.

35.

36. * 37.

38.

39.

40.

MS1231 MS1237 5HPF33 “ 5HP23N182 “ 5HP23N183 “ 5HPYNTL12005 “ 5HP23N184 “ 5HPYBHH12035 “ 5HP23N185 “ 5HPYWFL12005 “ 5HP23N186 “ 5HPYBHH12010 “ 5HPD107 “ 5HPX79 “ 5HP23N187 “ 5HPYNHX16005 “ 5HP23N188 “ 5HPYBHH16045 “ 5HP23N63 “ 5HPF129 “ 5HPF92 “ 5HPYPLY08010 “ 5HP23N305 “ 5HP23N66 “ 5HP23N67 “ 5HPHE42 “ 5HPF54 “ 5HP12N29 “ 5HPF73 “ 5HP5B10 “ 5HP5B9 “ 5HPF114 “ 5HPF115 “ 5HPF14 “ 5HPF16 “ 5HP23N68 “ 5HP23N69 “ 5HP23N70 “ 5HP37N72 “ 5HP23N71 “ 5HP23N72 “ 5HPYPEX10020 “ 5HP27N49 “

MS1243 “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “

NOTE: “(SAME PART NO. AS MODEL MS1231) *(MEANS NOT SHOWN)

-31-

DESCRIPTION Cable Guide Bracket Rope 3/8” Lock Nut Bracket 3/8” x 1-1/4” Bolt Spring Bracket 3/8” Flat Washer Dog Spring 3/8” x 1” Bolt Spacer S-Hook Spring HEX Nut, 1/2” Shifter Bracket Bolt, 1/2” X 1-1/4” GR.5 Tightener Rod Washer Shield Bracket Clip Pin Front Shield Shield Tailgate Hose Bracket Hydraulic Drive Bracket Shield Bearing Snap Ring 1/4” x 1” Key 3/8” x 1-1/4” Key Flange w/Zerk Bearing (Grease Type) Bearing Flange Lock Collar Front Adjustment Plate Spacer 25T Sprocket 16T Sprocket (Optional 1,000 RPM) #60 Roller Chain 122 Pitches Front Shaft 5/16” x 2-1/4” Roll Pin Jack

FIGURE 3

-32-

FIGURE 3 FRONTIER MODELS MS1231, MS1237 & MS1243 FRONT SHIELDS AND DRIVE ASSEMBLY ITEM * 41.

42.

43. * 44.

45.

46.

47.

48.

49.

50.

51.

52.

53.

54.

55.

56.

57.

58.

59.

60.

61.

62.

63.

64.

65.

66.

67.

68.

69.

70.

71.

MS1231 5HP12N120 5HP27N51 5HP27N50 5HP12N119 5HP12N118 5HP23N74 5HPF114A 5HP23N189 5HPD81 5HPD31 5HP23N190 5HP23N191 5HP31N17 5HP23N79 5HP23N80 5HP23N192 5HPK68 5HP23N193 5HP23N194 5HP23N195 5HP23N196 5HPX43 5HP23N197 5HPF84 5HPF44 5HP23N198 5HP31N27 5HP23N242 5HP23N278 5HP37N74 5HP23N306 5HPS522 5HPC112G01

MS1237 MS1243 “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ 5HP37N27 5HP37N27 “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ 5HP37N64 5HP37N64 5HP37N53 5HP37N53 5HPF92 5HPF92 “ “ “ “ “ “ “ “ “ “

NOTE: “(SAME PART NO. AS MODEL MS1231) *(MEANS NOT SHOWN)

-33-

DESCRIPTION Jack Gear Repair Kit Jack Mount Jack Pin & Chain Handle Replacement Bearing Bearing Plate Flange Snap Ring Lock Nut Shear Bolt Shear Hub 30T Sprocket Side Shield Bracket Shield Front Shifter Arm Washer Dog Bolt Shifter Panel Speed Selector Cotter Pin Shifter Arm Turnbuckle Cable Loop Cable Chain Cable Shield Bracket Spacer Front Shaft Guard Front Shield LH Manual Holder Shear Hub Spacer

FIGURE 4

-34-

FIGURE 4 FRONTIER MODELS MS1231, MS1237 & MS1243 BACK SHIELDS AND DRIVE ASSEMBLY ITEM 1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

11.

12.

13.

14.

15.

16.

17.

18.

19.

20.

21.

22.

23.

24.

25.

26.

27.

28.

29.

30.

31.

32.

33.

34.

35.

36.

37.

38.

39.

40.

41.

42.

43.

44.

45.

46.

MS1231 MS1237 5HP23N200 “ 5HP23N79 “ 5HP31N28 HP37N54 5HP23N201 HP37N55 5HP23N202 HP37N56 5HP23N203 HP37N57 5HP23N204 “ 5HP23N96 “ HPF92 5HPYPLY08010 “ 5HP23N205 “ 5HP23N206 “ 5HPYNHX12005 “ 5HP23N207 “ 5HPK103 “ 5HPYBTE08005 “ 5HP23N85 “ 5HP23N86 “ 5HPD57 “ 5HP23N208 “ 5HP23N209 “ 5HPYNTL08005 “ 5HP23N210 “ 5HP23N211 “ 5HPYWFL12005 “ 5HP23N206 “ 5HP23N212 “ 5HPYBTE12005 “ 5HPF44 “ 5HP31N27 HP37N53 5HP5B9 “ 5HP5B10 “ 5HP23N97 “ 5HP31N29 HP37N58 5HPF6 “ 5HP23N215 “ 5HP23N93 “ 5HP23N216 “ 5HP31N33 “ 5HP23N218 “ 5HP3G19 “ 5HP31N36 “ 5HPF16 “ 5HP10R11 “ 5HP23N220 “ 5HPF114A “

MS1243 “ “ HP37N54 HP37N55 HP37N56 HP37N57 “ “ HPF92 “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ HP37N53 “ “ “ HP37N58 “ “ “ “ “ “ “ “ “ “ “ “

NOTE; -(PART IS NOT USED ON THIS MODEL)

-35-

DESCRIPTION Cable Guard Side Shield Bracket Side Shield Shield Back Shield top Back Shield Cover Shield Bracket Angle Lynch Pin, 1/4” X 1-1/2” Clutch Rod Shifting Rod Bracket Nut 3/8”- 16 Spring Bracket Spring Eye Bolt, 1/4”X 1” Full Thread Top Angle Shifter Bracket Shifter Lever Yoke w/Zerk Collar Top Lock Nut, 1/4”-20 Shifting Rod Spring Flat Washer, 3/8” USS Shifting Rod Bracket Coupling Nut Eye Bolt, 3/8” X 1” Cable Loop Cable 1/4” x 1-1/4” Woodruff Key 3/8” x 1” Woodruff Key Side Bearing Bracket Side Shaft Collar Clutch Throw-Out #50 Roller Chain 60 Pitches Clutch Sprocket Spring Tightener Bearing Snap Ring Tightener Bracket Lock Collar 13T Sprocket # 50 Roller Chain 59 Pitches Flange

FIGURE 4

-36-

FIGURE 4

ITEM 47.

48.

49.

50.

51.

52.

53.

54.

55.

56.

57.

58.

59 60.

61.

62.

63.

64.

65.

66.

67.

68.

69.

70.

71.

72.

73.

74.

75.

76.

77.

78.

79.

80.

81.

82. * * * 83.

84.

85.

86.

87.

FRONTIER MODELS MS1231, MS1237 & MS1243 BACK SHIELDS AND DRIVE ASSEMBLY

MS1231 MS123 5HPF115 “ 5HPF14 “ 5HP23N174 “ 5HP23N241 “ 5HPD68 “ 5HP23N90 “ 5HP23N89 “ 5HP23N88 “ 5HP23N95 “ 5HP23N94 “ 5HPX85 “ 5HP23N221 “ 5HP23N222 “ 5HPYNTL08005 “ 5HPYBHH08035 “ 5HP23N224 “ 5HP23N225 “ 5HPF157 “ 5HP23N226 “ 5HP23N227 “ 5HPYBHH08035 “ 5HP23N228 “ 5HPYPCT04005 “ 5HP23N229 “ 5HPD64 “ 5HPD63 “ 5HP23N230 “ 5HP12N34 “ 5HP12N33 “ 5HP12N35 “ 5HP12N36 “ 5HP23N239 “ 5HPYSFD12005 “ 5HP31N34 “ 5HP31N35 “ 5HPYPCT04005 “ 5HPX60 “ 5HPX61 “ 5HP31N38 “ 5HP31N44 5HP37N76 5HP31N45 5HP37N75 5HP37N76 5HP31N46 5HP37N77 5HPF33 “

MS1243 “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ 5HP37N76 5HP37N75 5HP37N76 5HP37N77 “

NOTE; “(SAME PART NO. AS MS1231) *(MEANS NOT SHOWN)

-37-

DESCRIPTION Bearing Flange Flange Spacer Clutch Bronze Bushing Clutch Spring Bottom Angle Worm Box Holder Spacer Flange Bearing with Setscrews Shear Plate Top Lock Nut, 1/4” - 20 Shear Bolt, 1/4” X 1-1/4” Gr.5 Shear Hub Bronze Ring Connector Link w/Pins 30T Sprocket Snap Ring Shear Bolt,1/4” X 1-1/4” Gr.5 Spacer Cotter Pin, 1/8” X 1” Dog Spring 25T Sprocket Shear Hub Bearing Panel Bearing Cover Bearing Holder Bearing Shifter Support Set Screw, 3/8” - 16 X 3/4”Socket Pt. LH Tightener Bar RH Tightener Bar Cotter Pin, 1/8” X 1” #50 Offset Link #50 Conn. Link Chain Tightener Assembly #2 Side Shaft Guard #1 Side Shaft Guard #4 Side Shaft Guard #3 Side Shaft Guard Cable Guide

FIGURE 5

-38-

FIGURE 5 FRONTIER MODELS MS1231, MS1237 & MS1243 HYDRAULIC TAILGATE ASSEMBLY ITEM 1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

11.

12.

13.

14.

15.

16.

MS1231 5HP23N298 5HP23N99 5HP23N100 5HP31N37 5HP23N104 5HP23N105 5HP23N67 5HPK132 5HP23N107 5HPYPCT07005 5HPYPEX10015 5HP23N109 5HP23N299 5HP23N111A

MS1237 5HP37N79 5HP37N35 5HP37N36 5HP37N69 “ “ “ “ “ “ “ “ “ “

MS1243 5HP37N34 5HP37N35 5HP37N36 5HP43N5 5HP37N69 5HP43N6 “ “ “ “ “ “ “ “ 5HP23N110 “

17.

18.

5HP23N231 5HP23N113

5HP37N59 5HP37N60

5HP37N59 5HP37N60

19.

5HP23N114

5HP37N61

5HP37N61

20.

5HP23N300 “ 5HP23N115 21.

5HP23N116 “ “ 22.

5HP23N117 “ “ 23.

5HP31N50 5HP37N83 5HP37N83 24.

5HP23N163 “ “ 25.

5HP23N232 “ “ 26 5HP23N233 5HP37N62 5HP37N62 27.

5HP23N234 “ “ 28.

5HP12V3 29.

5HP23N301 “ “ NOTE: “(SAME PART NO. AS MODEL MS1231) -(PART IS NOT USED ON THIS MODEL)

-39-

DESCRIPTION Tailgate Frame RH Side Rubber LH Side Rubber Back Extension Tailgate Plywood with Poly Extension Angle Tailgate Corner Bottom Rubber Hose Bracket Spacer Cylinder Pin Cotter Pin,7/32” X 2” Roll Pin 5/16” x 1-3/4” Washer RH Tailgate Mount Hydraulic Cylinder (1 Standard on MS1231 2nd Optional) Brace Hose (HP23N113-96”/HP37N60-108”) Optional on MS1231 Hose (HP23N114-138”/HP37N61-152”) Optional on MS1231 LH Tailgate Mount Tee Hose Holder Hose (HP31N50-316”/HP37N83-328”) Tailgate Poly Hold Down Tailgate Bracket Brace Brace 90° Street Elbow 3/8” Self Tapping Bolt Cylinder Pin

FIGURE 6

FRONTIER MODEL MS1231, MS1237 &MS1243 APRON CHAIN ASSEMBLY ITEM 1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

11.

12.

13.

14.

15.

16.

17.

18.

19.

MS1231 MS1237 MS1243 5HP37N82 “ “ 5HP23N303 “ “ 5HP27N19 “ “ 5HPS138 “ “ 5HP23N121 “ “ 5HP23N122 “ “ 5HP31N21 5HP37N42 5HP37N42 5HP23N124 “ “ 5HPS55 “ “ 5HPS55 “ “ 5HP31N22 5HP37N43 5HP37N43 5HPA30 “ “ 5HP23N126 “ “ 5HP23N127 “ “ 5HP23N128 “ “ 5HPYBCR16045 “ “ 5HPYBHH16145 “ “ 5HPA29 “ “ 5HP23N266 “ “ NOTE: “ (SAME PART NO. AS MODEL MS1223) - (PART IS NOT USED ON THIS MODEL)

-40-

DESCRIPTION Drive Shaft Shield 3/8” x 1-3/4” Square Key Drive Shaft 3/8” x 2-3/8” Sq.Key w/Round Ends Spacer 5/8” Drive Sprocket 6T Apron Chain 26 Slats, 262 Links Apron Chain 28 Slats, 280 Links Slat w/Attachment Links T-Rod Standard Link T-Rod Standard Link Apron Chain Side Spacers Chain Slide Plate LH Chain Slide Spacer T-Rod Slide LH T-Rod Slide RH 1/2” x 4” Carriage Bolt GR.5 1/2” x 4-1/2” Bolt GR.5 Chain Slide Plate RH Spacer 5/16”

FIGURE 7

FRONTIER MODEL MS1231, MS1237 & MS1243 OPTIONAL HYDRAULIC DRIVE ASSEMBLY

ITEM MS1231 MS1237 MS1243 1.

5HPHE58 “ “ 2.

5HPDF15 “ “ 3.

5HPDF18 “ “ 4.

5HPDF7 “ “ 5.

5HPDF8 “ “ 6.

5HPHE14 “ “ 7.

5HP23N131 “ “ 8.

5HP11S19 “ “ 9.

5HP5B10 “ “ 10 5HPDF1 “ “ 11.

5HP23N117 “ “ 12.

5HP23N132 “ “ 13.

5HPDF21 “ “ 14.

5HP23N133 “ “ 15.

5HPDF9 “ “ 16.

5HPYNTL12005 “ “ 17.

5HPDF12 “ “ 18.

5HPDF11 “ “ 19.

5HPDF10 “ “ 20.

5HPDF14 “ “ 21.

5HPDF22 “ “ 22.

5HP31N23 “ “ 23.

5HPHE12 “ “ 24.

5HP10R32 “ “ 25.

5HP23N238 “ “ 26.

5HPL10R35 “ “ NOTE: “(SAME PART NO. AS MODEL MS1231)

-41-

DESCRIPTION 90° Street Elbow Speed Control Check Valve Nipple Tee Hose Bracket #50 Roller Chain 40 Pitches 20T Sprocket 1/4” x 1” Woodruff Key Hydraulic Motor Hose Holder Hydraulic Motor Hose Reducer Control Panel Hose for Handle Top Lock Nut, 3/8” - 16 Washer Handle Handle Bracket Strap Ring for Strap Coupling Hose Snap Ring Chain Tightener Roller Tightener Bracket

FIGURE 8

-42-

FIGURE 8 FRONTIER MODELS MS1231, MS1237 & MS1243 WORM GEARBOX ASSEMBLY ITEM MS1231 MS1237 MS1243 1.

5HPG114 “ “ 2.

5HPG116 “ “ 3.

5HPG76 “ “ 4.

5HPG77 “ “ 5.

5HPG78 “ “ 6.

5HPG79 “ “ 7.

5HPX8 “ “ 8.

5HPG81 “ “ 9.

5HPG82 “ “ 10.

5HPYSKP12025 “ “ 11.

5HPYSKP12005 “ “ 12.

5HPG122 “ “ 13.

5HPG123 “ “ 14.

5HP17G133 “ “ 15.

5HPG65 “ “ 16.

5HPG117 “ “ 17.

5HPG89 “ “ 18.

5HPG90 “ “ 19.

5HPG91 “ “ 20.

5HPG92 “ “ 21.

5HPG93 “ “ 22.

5HP23N236 “ “ 23.

5HP5B10 “ “ NOTE: “(SAME PART NO. AS MODEL MS1231)

-43-

DESCRIPTION Housing Cover Worm Worm Gear Bearing #15101 Bearing Cup #15245 Bearing - Oil Lite Bearing - Oil Lite Snap Ring Setscrew 3/8” NC x 3/8” Long Capscrew 3/8” NC x 1” Long Worm Gearbox Complete Seal Seal Plug 3/8” NPT Cap 1-7/8” Zerk 1/4”-28 Cap Vent Plug 3/8” NPT Shim Spacer Worm Gear Shaft 1/4” x 1” Woodruff Key

FIGURE 9

-44-

FIGURE 9 FRONTIER MODELS MS1231, MS1237 & MS1243 BEVEL GEARBOX ITEM MS1231 MS1237 MS1243 1.

5HPG50 “ “ 2.

5HPG51 “ “ 3.

5HP23N136 “ “ 4.

5HPG53 “ “ 5.

5HPG54 “ “ 6.

5HPG55 “ “ 7.

5HPYBHH10132 “ “ 8.

5HPG57 “ “ 9.

5HP31N39 “ “ 10.

5HP23N137 “ “ 11.

5HP31N40 “ “ 12.

5HPG61 “ “ 13.

5HPG63 “ “ 14.

5HPG64 “ “ 15.

5HPG65 “ “ 16.

5HPG66 “ “ 17.

5HPG67 “ “ 18.

5HPG68 “ “ 19.

5HPG69 “ “ 20.

5HPYBHH10130 “ “ 21.

5HP31N41 “ “ 22.

5HP31N42 “ “ NOTE; “(SAME PART NO. AS MODEL MS1231)

-45-

DESCRIPTION Housing Cover Bevel Gear 24T Bearing #14137A Bearing Cup #14276 Snap Ring Capscrew, 5/16” X 5/8” Stake Nut 1-1/2” Stake Nut 1-1/8” Shaft - Output Shaft - Input Double Splined “E” (1210) Woodruff Key (Hard5) Seal - Output Seal - Input Plug 1/8” NPT Gasket Plug 1/8” NPT Cap Shim 5/16” x 5” Bolt GR.5 Bevel Gear 16T-Splined Bevel Gearbox Complete

FIGURE 10

FRONTIER MODELS MS1231, MS1237 & MS1243 HYDRAULIC CYLINDER ITEM MS1231 MS1237 MS1243 1.

5HP23N142A “ “ 2.

5HP23N143A “ “ 3.

5HP23N144 “ “ 4.

5HP23N145A “ “ 5.

5HP23N146 “ “ 6.

5HP23N147 “ “ 7.

5HP23N148 “ “ 8.

5HP23N149 “ “ 9.

5HP23N150A “ “ 10.

5HP23N151 “ “ 11.

5HP23N111A “ “ NOTE “(SAME PART NO, AS MODEL MS1231)

-46-

DESCRIPTION Clevis Cap Rod Cap Piston Rod Cylinder Tube Tie Rod Piston Nut Plug Rod Clevis Seal Kit Hydraulic Cylinder

FIGURE 11

FRONTIER MODELS MS1232, MS1237 & MS1243 PTO ASSEMBLY ITEM MS1231 MS1237 MS1243 1000 RPM 1.

5HP23N152 “ “ 5HP23N313 2.

5HP23N153 “ “ “ 3.

5HPG1R35 “ “ “ 4.

5HP14NWKIT “ “ “ 5.

5HP23N155 “ “ “ 6.

5HP24N26 “ “ “ 7.

5HP4N20 “ “ “ 8.

5HP23N156 “ “ “ 9.

5HP23N157 “ “ 5HP23N314 10.

5HP23N158 “ “ 5HP23N315 11.

5HP23N159 “ “ “ 12.

5HP23N162 “ “ “ * 5HP37N73 “ “ 5HP37N73 13.

5HPS225 “ “ “ 14.

5HPS226 “ “ “ 15.

5HPS212 “ “ “ 16.

5HPS227 “ “ “ 17.

5HPS228 “ “ “ 18.

5HPS229 “ “ “ 19.

5HPS215 “ “ “ * 5HPS402 “ “ “ NOTE: “(SAME PART NO. AS MODEL MS1231) *(MEANS NOT SHOWN)

-47-

DESCRIPTION PTO Assembly Complete w/Shields Machine Half PTO w/Shield End Yoke Machine Half Repair Kit Yoke and Tube Bearing Retainer Nylon Bearing Inner Guard Including Item #6 & #7 Tractor Half PTO w/Shield Outer Guard Including Item #6 & #7 Yoke and Shaft Lock Yoke Assembly Optional 1000 RPM Yoke (1-3/8”) Spring Lock Repair Kit Cover Stainless Ball Washer Spring Collar Assembly Retaining Ring PTO Saftey Manual

FIGURE 12

FRONTIER MODELS MS1231, MS1237 & MS1243 OPTIONAL 2ND BEATER ITEM 1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

11.

MS1231 5HP23N308 5HPF114A 5HPF115 5HPF14 5HPF16 5HP23N164 5HP23N165 5HP23N166 5HPG23 5HPD18 5HP23N167

MS1237 “ “ “ “ “ “ “ “ “ “ 5HP37N49

MS1243 “ “ “ “ “ “ “ “ “ “ 5HP37N49

12.

5HP12N42 “ “ 13.

5HP23N168 14.

5HPF13 “ “ 15.

5HP5B9 “ “ 16.

5HPF56 “ “ 17.

5HP23N169 “ “ 18.

5HP23N170 5HP37N48 5HP37N48 19.

5HP23N171 5HP37N45 5HP37N45 20.

5HP23N172 5HP37N46 5HP37N46 21.

5HP23N173 5HP37N47 5HP37N47 22.

5HPF73 “ “ 23.

5HPF114 “ “ 24.

5HPYBCR16040 * 5HPYBCR16030 5HPYBCR16030 NOTE: “(SAME PART NO. AS MODEL MS1231) -(PART IS NOT USED ON THIS MODEL)

-48-

DESCRIPTION Bearing Flange Guard Bearing Flange w/Zerk Bearing Bearing Flange Lock Collar LH Stub Shaft RH Stub Shaft 2nd Beater 5/16” x 1-3/8” Square Key Sprocket #60 Roller Chain MS1231 81 Pitches MS1237 & MS1243 79 Pitches Idler Sprocket Spacer Sprocket 3/8” x 1-1/4” Key Clip Pin Cover Shield Shield RH Panel LH Panel Snap Ring Flange w/Straight Zerk 1/2” x 3-1/2” Carriage Bolt GR.5 1/2” x 2-1/2” Carriage Bolt GR.5

FIGURE 13

FRONTIER MODELS MS1231, MS1237 & MS1243 OPTIONAL ELECTRIC CONTROL FOR HYDRAULIC DRIVE ITEM ITEM MS1231 MS1237 MS1243 DESCRIPTION 22.

1. 5HP43H1 “ “ Motor Shield/Holder 23.

2. 5HP43H3 “ “ Shield Bolt 24.

3. 5HPYWLO08005 “ “ Lockwasher, 1/4” 25.

4. 5HPYNTL08005 “ “ Top Lock Nut, 1/4” 5. 5HPYBCR08025 “ “ Carr. Bolt,1/4”X2 1/2 27.

28.

6. 5HPYNTL12005 “ “ Top Lock Nut, 3/8” 29.

7. 5HP43H5 “ “ Flow Indicator 30.

8. 5HPDF15A “ “ Flow Control 31.

9. 5HPDF18 “ “ Check Valve 32.

10. 5HPHE58 “ “ Elbow 33.

11. 5HPDF4 “ “ Nipple 34.

12. 5HPDF8 “ “ Tee 35.

13. 5HP16SV246 “ “ Gear Motor 36.

14. 5HP23N133 “ “ Control Panel 15. 5HP16SV272 “ “ Spreader Control Cord 37.

16. 5HP16SV321 “ “ Control End Complete 38.

17. 5HP16SV270 “ “ Tractor Power Supply 39.

18. 5HP16SV271 “ “ Cont. Box Power Supply 40.

41.

19. 5HP16SV316 “ “ Control Box 42.

20. 5HP16SV317 “ “ Control Box Gasket 43.

21. 5HP16SV318 “ “ Control Box Cover 44.

NOTE: “ (SAME PART NO. AS MODEL MS1231) 45.

- (PART IS NOT USED ON THIS MODEL)

-49-

MS1231 MS1237 MS1243 DESCRIPTION 5HP16SV319 “ “ Apron Speed Switch 5HP16SV235 “ “ Flow Control Switch Boot 5HP16SV231 “ “ Fuse Holder 5HP16SV232 “ “ Fuse 5 Amp (AGC-5) 5HPHE12 “ “ Hose Extension 5HP31N23 “ “ 3/8” Coupling 5HP23N132 “ “ Hydraulic Motor Hose 5HPDF1 “ “ Hydraulic Motor 5HP11S19 “ “ Drive Sprocket 5HPYSKP10010 “ “ Setscrew (5/16”-18) 5HPL10R35 “ “ Tightner Bracket 5HP23N238 “ “ Tightner Roller 5HP10R32 “ “ Snap Ring 5HPX61 “ “ #50 Chain Connector 5HP23N131 “ “ #50 Chain (40 Pitches) 5HPX60 “ “ #50 Chain Offset 5HPHE14 “ “ Hose Bracket 5HP23N117 “ “ Hose Holder 5HP5B10 “ “ 1/4” x 1” Woodruff Key 5HPBFR320 “ “ Flag Electrical Connector 5HP16SV269 “ “ Tractor Power Supply Cord 5HP23N309 “ “ Hydraulic Hose 5HPDWM205 “ “ Male Hydraulic Tip

SERVICE / MAINTENANCE RECORD DATE

DESCRIPTION

NOTES

-50-