Dynapac WEDA LINE Submersible Pumps WEDA 90 INSTRUCTIONS & SPARE PARTS CATALOGUE Manual 470W367058

WEDA LINE Submersible Pumps WEDA 90

Instructions and spare parts catalog

470W367058_ENG_NO Rev. : G

INSTRUCTIONS MANUAL – WEDA 90

GENERAL SAFETY RULES WARNING

Read and understand all instructions

Failure to follow all instructions listed below, may result in electric shock, fire and/or serious injury.

Before using the machine, read carefully these instructions and keep them in a safe place.

These safety recommendations have been compiled from international safety standards. Local regulations must also be checked and observed.

SAVE THESE INSTRUCTIONS WORK AREA Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents.

Do not operate pumps in explosive atmospheres, such as presence of flammable liquids, gases or dust. Pumps create sparks which may ignite the dust or fumes.

Keep bystanders, children, and visitors away while operating a pump. Distraction can cause you to loose control.

ELECTRICAL SAFETY Pumps must be plugged into an outlet properly installed and grounded in accordance with all codes and ordinances. Never remove the grounding prong or modify the plug in any way. Do not use any adaptor plugs. Check with a qualified electrician if you are in doubt as to whether the outlet in properly grounded. If the pumps should electrically malfunction or break down, grounding provides a low resistance path to carry electricity away from the user.

Avoid body contact with grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increase risk of electric shock if your body is grounded.

Do not abuse the cord. Never use the cord to carry the pumps or pull the plug from an outlet. Keep cord away from heat, oil, sharp edges or moving parts. Damaged cords increase the risk of electric shock.

Use a network protected by a ground fault circuit interrupter.

PERSONAL SAFETY Stay alert, watch what you are doing and use common sense when operating a pump. Do not use pump while tired or under influence of drugs, alcohol or medication. A moment of inattention while operating pumps result in serious personal injury.

Dress properly. Do not wear loose closing or jewellery. Contain long hair. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewellery, or long hair can be caught in moving parts.

Always use approved safety equipment. Always wear eye protection. The following safety equipment applies to operators and other personnel in the immediate vicinity of the working zone.

Safety helmet.

Ear protectors.

Dust mask in dusty environments.

Protective gloves.

Protective shoes.

Goggles.

Remove adjusting keys or switches before turning the pump on. A wrench or a key that is left attached to a rotating part of the pump may result in personal injury.

2/21

INSTRUCTIONS MANUAL – WEDA 90 The admissible sound level of 85 dB (A), can be exceeded because of the machine and/or the application. Long time exposure to loud noise without ear protectors can cause permanent damage to hearing.

PUMP USE AND CARE Never operate the pump without the strainer. It both protects the pumps and the pipes.

Do not force pump. Use the correct pump for your application. The correct pump will do the job better and safer at the rate for which it is designed.

The use of the machine is restricted to the applications specified in the product literature.

Disconnect the plug from the power source before making any adjustments, changing accessories, or storing the pump. Such preventive safety measures reduce the risk of starting the pump accidentally.

Store idle pumps out of reach of children and other untrained persons. Pumps are dangerous in the hand of untrained users.

Maintain pumps with care. Properly maintained pumps are less likely to bind and are easier to control.

Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the pumps operation. If damaged, have the pump serviced before using. Many accidents are caused by poorly maintained pumps.

The machine must not be modified without prior consent of the manufacturer. Use only original parts. If modifications are made without prior consent of the manufacturer there is a risk of serious injury to the personal.

SERVICE Pump service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified personnel could result in a risk of injury.

When servicing a pump, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized parts or failure to follow Maintenance Instructions may create a risk of electric shock or injury.

Make sure that the signs about using, safety, and maintenance are always legible.

Always change damaged parts immediately. Change wear parts in due time.

3/21

INSTRUCTIONS MANUAL – WEDA 90

GENERAL The WEDA submersible drainage pumps are designed for pumping lightly contaminated water.

DESIGN The heavy duty light weight aluminium construction includes a cooling jacket ensuring adequate motor cooling at all times.

The WEDA LINE pumps are in 'plug and pumping design’, with built-in full overheat motor protection.

The versions with NVB allow automatic operation.

The unique cartridge type seal package can be easily replaced on site with only minimum downtime.

For demanding applications as in construction works and mining, the impellers are made for wear resistant Hi-Chrome iron and all other components are rubber lined.

The impeller clearance is easily adjustable to compensate for wear.

TECHNICAL DATA Pump Discharge

WEDA90 100 (4”) 150 (6”) 5-8 40°C 20 Ø7 180 Rectangular holes 7 x 43.5 mm 2850 - (3420) F (155°C)

mm - (in)

Suitable for media with pH Maximum water temperature Maximum submersible depth Maximum solids size Weight (excluding cable ) Strainer Speed rpm Stator insulation class Voltages V

m - (ft) mm – (in) kg - (lb) 50Hz (60Hz)

Phases

220V 380-400 415 440-460 Other voltages upon request

3 3 3 3

Frequency Hz 60 50 50 60

Rated current A L 92 45.3 43.6 45.9

H 47.7 46 45.5

Rated electrical power (kW) L H 32 28.4 30.2 28.4 30.2 32 32.4

IMPORTANT The above information is a general description only, is not guaranteed and contains no warranties of any kind Power cables (50Hz) 20 meters 4x16mm² All cables polychloroprene type HO7RN-F .

Power cables (60Hz) only for CSA approved types 20 meters SOW 4xAWG6

220V

400-415V

440V

300

400

cable section (mm2)

35 25 16 10

100

200

cable length authorized (m)

4/21

500

INSTRUCTIONS MANUAL – WEDA 90

HYDRAULIC CHARACTERISTICS 50Hz

60Hz

Power (hp) Electrical

Power (kW) Electrical

A cco r d ing t o ISO 9 9 0 6 - A N N EX A

A cco r d ing t o ISO 9 9 0 6 - A N N EX A

42

32

1

1

28

2

34

Power (kW)

Power (hp)

38

30 26 22

2

24 20 16

0

200

400

600

800

1000

1200

1400

1600

1800

2000

0

500 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000 6500

Flow (US gpm)

Flow (l/min)

Curve Head x Flow

Curve Head x Flow

A cco r d ing t o ISO 9 9 0 6 - A N N EX A

A cco r d ing t o ISO 9 9 0 6 - A N N EX A

300

90 80

250

1 : High head

60 Head (m)

Head (ft)

1 : High head

70

200 150 100

2 : Low head

50 40 30

2 : Low head

20

50

10 0

0 0

200

400

600

800

1000

1200

1400

1600

1800

2000

0

500 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000 6500

Flow (US gpm)

Flow (l/min)

DIMENSIONS Dimensions in mm / in

DISCHARGES AVAILABLE 4’’ 4’’ 4’’ 6’’ 6’’ 6’’

P/N 470W203564 470W203482 470W203572 470W283166 470W283176 470W283168

Hose standard with 2 clamps BSP - thread NPT - thread Hose standard with 2 clamps BSP - thread NPT - thread

5/21

+ jointing bracket 470W282059

INSTRUCTIONS MANUAL – WEDA 90 The discharges have to be ordered separately .

INSTALLATION The pump must not be used in an explosive / inflammable environment or used to pump inflammable liquids !

Route the cables so that connectors do not lie in the water. Consider the risk of electrical accident.

Never lift the pump by its power cable !

Connect a discharge hose of approved pressure class.

The discharge hose may be thrown off when the pump starts.

No one must be allowed in the water, e.g. swimming pools, when the pump is running.

Check that the pump is standing steady, or suspend it from its lifting ring.

Check the direction of rotation, pointed by the starting kick arrow printed in the outer casing (anticlockwise) The pump will start instantaneously when it is connected to the power supply.

The pump may kick violently when it starts.

In case of wrong direction of rotation two phases should be inverted from the supply (three phases voltage only).

Direction of rotation

ELECTRICAL CONNECTION Check that the details on the pump data plate match with the mains voltage and frequency.

The electrical installation must be carried out by a qualified electrician!

Local installation regulations must be followed!

Make sure that the pump is properly earthed.

The earth conductor must be slightly longer than the phase conductors. If the motor power cable is accidentally pulled off, the earth conductor must be the last conductor to be removed from the terminals.

"USE WITH APPROVED MOTOR CONTROL THAT MATCHES MOTOR INPUT IN FULL LOAD AMPERES WITH OVERLOAD ELEMENTS SELECTED OR ADJUSTED IN ACCORDANCE WITH THE CONTROL INSTRUCTIONS"

BUILT-IN MOTOR PROTECTION Check that the pump is disconnected from the power supply before starting any work !

The pump's built-in motor protection switches off the contactor automatically if the motor overheats. Then, the fault must be identified and corrected.

After cooling to normal working temperature, the motor protection switches on the contactor and the pump starts again.

6/21

INSTRUCTIONS MANUAL – WEDA 90

TROUBLE SHOOTING Fault location Pump will not start.

Cause 1. Fuses blown 2. Broken cable 3. Power failure 4. Jammed impeller 5. Faulty contactor 6. Stator winding burnt-out 7. Incorrect phase sequence (3 phases)

Pump starts, but stops again. 1. Pump runs backwards (3 phases) 2. Pump connected to wrong voltage 3. Phase interruption 4. Strainer blocked 5. Insufficient water level 6. Voltage too low when using an extra cable 7. Water too hot Pump works, but delivers too 1. Impeller worn small water volume .

2. Pump runs backwards (3 phases) 3. Hose dimensions unsuitable 4. Insufficient discharge head

Action 1. Replace fuses 2. Service 3. – 4. Clean bottom of pump 5. Service 6. Service 7. Change 2 phases in plug 1. Change 2 phases in plug 2. Select the right voltage 3. Check fuses 4. Clean strainer 5. Stop the pump 6. Increase the extra cable section 7. Switch off power 1. Adjust pump/replace impeller 2. Change 2 phases in plug 3. Change to suitable hose 4. Select a bigger pump

MAINTENANCE PUMP PERFORMANCE To keep the pump performance, the gaps must be as small as possible. The gap between the impeller and the wear plate is adjustable with trim washers. The gap between the impeller and the diffuser is adjusted by alternatively tightening the nuts fixing the diffuser. After adjustment the impeller must be capable of rotation by hand.

Fig 1 Worn impeller can have very sharp edges . Wear safety gloves !

7/21

INSTRUCTIONS MANUAL – WEDA 90 SEAL UNIT Every six months, check the level and quality of the oil in conjunction with servicing. If the oil is emulsified with water, the seal package must be removed from the rotor shaft for replacement. (See Fig. 2).

Company Oil Statoil Hydra Way HM32 Texaco Ranco Oil HD32 Mobil DTE24 Castrol Hyspin AWS32 Shell Tellus oil32 Quantité : 5,2 L Fig 2

ACCESSORIES SERIAL COUPLING 6" NPT P/N 470W293234 SERIAL COUPLING 6" BSP P/N 470W293232 DISCHARGE 8" FOR HOSE P/N 470W293095 NON RETURN VALVE 6" P/N 470W209751 ZINC ANODES P/N 470W294197 When pumping salt water (which is highly aggressive towards aluminium), the pump should be protected with zinc anodes.

INSTALLATION

8/21

INSTRUCTIONS MANUAL – WEDA 90

ELECTRICAL CONNECTION

CONNECTION ∆ 3 PHASES DELAYED START + OVER CURRENT RELAY

CONNECTION Y 3 PHASES DELAYED START + OVER CURRENT RELAY

9/21

INSTRUCTIONS MANUAL – WEDA 90

Ү / ∆ START

10/21

INSTRUCTIONS MANUAL – WEDA 90

EXTRA EQUIPMENT OVERCURRENT RELAY The WEDA90 Seri pumps are equipped with an over current relay. In this case the pump has a reset button in the contactor cover.

If the relay trips, the cause must first be established before pressing the button to reactivate the relay.

For a direct start the relay is set to the rated current of the motor +10%. For a Y/D start, the setting is the same as the rated current (See pump data plate).

Start

Voltage

P/N

Direct

220V/440V-3-60Hz

470W294155

Direct

500V-3-50Hz

470W743517

Direct

230V/400V-3-50Hz 440V/500V-3-60Hz

470W743549

LEVEL SENSOR NVB The WEDA90L Seri pumps can be equipped with a built-in electronic level sensor, NVB. The pump starts automatically as the rising water reaches the electrodes on the contactor cover. The pump stops again , automatically , once the water level falls to the point at which the pump begin to suck in air through the strainer .

The level sensor can be disconnected by bridging between the probes.

A pump equipped with NVB will not start if the wrong phase sequence is connected, or in case of phase failure.

If the pump does not stop when the water comes to at the strainer level, open the pump cover and adjust the NVB potentiometer to the "-" direction to get the stop.

If the pump stop before the water comes to the strainer level, adjust to the "+" direction.

Note : This function is not working in case of high head pump.

REBUILDING SET NVB (PUMPS MANUFACTURED FROM SERIAL NUMBER 853000).

400V 50Hz 470W740309 BUILT IN LEVEL CONTROL NVB Description The NVB is an electronic device used to control a pumping operation. It is connected to a set of 2 x electrodes located on the pump contactor cover.

Features Pumping control of the pump according to the water level.

Pump protection, the pump will stop face to : o Wrong phase sequence (shift 2 wires in the plug to get the proper sequence).

11/21

o o o o

INSTRUCTIONS MANUAL – WEDA 90 Phase failure.

Overload (clogged strainer, etc…).

Overheating: controlled by thermos-switches inside the motor winding.

Running without water.

Pumping operation The pump starts when the water reaches the electrodes and stops when air is sucked through the strainer.

The water level, for starting, can be moved down using extension wires to connect on the electrodes.

The water level, for stopping, can be adjusted using the NVB potentiometer: o If the pump does not stop, when no water, turn the potentiometer clockwise until it stops. o If the pump stops before air suction, turn the potentiometer anti-clockwise.

NOTE: A jump (4) is delivered with the kit / pump. When connected on the electrode, the water level control is disabled on the pump continuously runs.

ELECTRICAL CONNECTION

ADJUSTMENTS You have 2 different potentiometers for adjustment.

1) Res A on the top of the NVB box 2) Res B in the box on the electronic board

The pump doesn’t stop when the water level sinks below the strainer A) Turn "Res A" clockwise! OK? B) "Res A" back to mid position !

Put the R-phase cable even through the second hole in the NVB-box ! OK ?

C) Turn "Res A" clockwise! OK? D) "Res A" back to mid position Turn "Res B" counter clockwise (on the electronic board - open up the NVB-box -adjust and close the box again) OK ?

E) Turn "Res B" according to D) above until the pump stops. Then fine adjust with "Res A".

The pump stops before the water level sinks below the strainer A) Just 1 cable through one of the holes in the NVB-box !

B) Turn "Res A" counter clockwise ! OK ?

C) "Res A" back to mid position !Turn "Res B" clockwise (on the electronic board - open up the NVB-box adjust and close the box again) OK ?

D) Turn "Res B" according to B) above until the pump stops when the water level sinks down to the strainer. Fine adjust with "Res A".

12/21

INSTRUCTIONS MANUAL – WEDA 90

SPARE PARTS CATALOGUE RESERVDELSTÄLLNING

ORDERING SPARE PARTS

Följande uppgifter ska lämmas vid beställning av reservdelar för att undvika leveransfel : 1. Maskintyp.

2. Maskinens seriunmmer.

3. Antal av önskad reservdel.

4. Reserdelens artikelnummer.

5. Reservedelens benämning.

6. Måttupgifter vid beställning av metervara.

To avoid errors in delivery, please give the following information when ordering spare parts : 1. Type of machine.

2. Machine serial number.

3. Quantity required.

4. Part number.

5. Parts description.

6. Dimensions when ordering per length.

ERSATZTEILBESTELLUNG

ORDINI DI RICAMBI

Zur Vermeidung von Fehllieferungen sind bei der Bestellung von Ersatzteilen folgende Angaben zu machen : 1. Mashinentyp.

2. Herstellungsnummer.

3. Bestellmenge. (Quantity) 4. Ersatzteilbenennung. (Part N°) 5. Ersatzteilbenennung. (Description) 6. Massangaben bei Bestellung von Meterware.

Per evitare errori nelle consegne di ricambi, Vi preghiamo di comunicarci le seguenti informazioni al momento dell ‘ordinazione : 1. Tipo di macchina.

2. Numero di serie della macchina.

3. Quantitá dei pezzi desiderati. (Quantity) 4. Numero di codice del pezzo. (Part N°) 5. Descrizione del pezzo di ricambio. (Description) 6. Misura, in caso di ordine per metro.

PEDIDO DE RECAMBIOS

COMMANDE DE PIECES DE RECHANGE

Para evitar errores en las entregas, deberá indicarse los siguientes datos al hacer un pedido de recambios : 1. Tipo de máquina.

2. Número de serie.

3. Cantidad de piezas deseadas. (Quantity) 4. Número de artículo de la pieza de recambio. (Part N°) 5. Denominación de la pieza. (Description) 6. Indíquese la medida al solicitar un artículo que se expide por metros.

Les indications suivantes doivent être fournies lors de la commande de pièces de rechange, afin d’éviter toute erreur de livraison : 1. Type de machine.

2. Numéro de série.

3. Quantité désirée de pièce de rechange. (Quantity) 4. Numéro de la pièce de rechange. (Part N°) 5. Description de la pièce de rechange. (Description) 6. Longueur en cas de commande par mètre.

13/21

INSTRUCTIONS MANUAL – WEDA 90 SPARE PARTS Note : To place spare parts order, use : - The serial number of the machine - The description and part number; MAINTENANCE KITS Part number 470W294324

Description

Parts included

Gasket set

Parts

470W209540

Start button Y/D

Parts

15, 16, 24, 25, 27, 34, 36, 49, 50, 51, 63, 68, 70, 84, 85 4, 5, 6, 7, 8, 9, 12, 13, 14.

470W209555

Start button direct start

Parts

4, 5, 6, 7, 8, 9, 12, 13, 14.

470W294199

Parts

59, 79, 83, 89, 90.

Parts

59, 79, 83, 89, 90.

Parts

59, 89, 95, 96, 97, 99.

Parts

59, 89, 95, 97, 99.

470W740309

WEDA90L Low Wear part set 50Hz pressure WEDA90L Wear part set Low 60Hz pressure WEDA90H Wear part set High 50Hz pressure WEDA90H Wear part set High 60Hz pressure Rebuilding set NVB direct start 380-460V

Parts

11, 100, 101, 102, 103, 104, 105, 106, 107, 109.

4700W60015

Oil amount 2L

470W294201 470W294200 470W294202

-

14/21

INSTRUCTIONS MANUAL – WEDA 90 SPARE PARTS LIST Ref

Designation

P/N

Qty L

Qty H

1 2 3 4 5 6 7

Handle complete Rivet Data plate Sealing Washer Sealing Piston direct start Piston Y/D start Spring Guide Nut Cover 380-500V Cover for NVB Nut Washer Screw O-ring O-ring Plug Sleeve 380-500V Sleeve220V Y/D Screw Thrust collar Nut Stud bolt Top bracket 220V direct start Top bracket 380-415V Y/D direct start Top bracket 380-415VY/D start Top bracket 230V for external protection Top bracket 230V Top bracket 380-415V external Y/D start without thermal protection O-ring O-ring Stud bolt O-ring Inner casing*** Stud bolt Stator See below Discharge 4" for hose Discharge 4" BSP thread Discharge 4" NPT thread Washer Stud bolt O-ring Jointing bracket Incl pos 12,32,33,36.

Discharge packing Discharge 6" for hose Discharge 6" BSP thread Discharge 6" NPT thread 2 Cable inlet cpl .4x10mm 415-550V Y/D start incl. pos 44,49 .

2 Cable inlet cpl .4x16mm 400V incl. pos 44,49 .

2 Cable inlet cpl .4x25mm 230V incl. pos 44,49 .

2 Cable 4x10mm 415-550V direct start 2 Cable 4x10mm 400V Y/Dstart 415V Y/D start 2 Cable 4x16mm 400V direct start

470W292062 4700W65430 470W743583 470W209428 470W209731 470W209429 470W209647 470W274084 470W209434 470W209435 4700W84211 470W292064 470W292213 4700W84210 470W209438 470W209501 4700W65134 4700W65251 470W294127 470W294164 470W294125 4700W78698 470W294126 4700W84213 4700W69656 470W368263 470W291020 470W292204 470W292312 470W293097 470W730011 4700W65033 4700W65177 470W294123 4700W65143 470W368282 470W293087 470W203564 470W203482 470W203572 4700W51170 4700W69640 470W743466 470W282059 470W284058 470W283166 470W283176 470W283168 470W284103 470W284104

1 4 1 1 1 1 1 1 1 1 6 1 1 7 1 1 3 1 2 2 2 1 2 2 6 1 1 1 1 1 1 1 2 2 1 1 4 1 1 1 6 6 1 1 1 1 1 1 1 1

1 4 1 1 1 1 1 1 1 1 6 1 1 7 1 1 3 1 2 2 2 1 2 2 2 1 1 1 1 1 1 2 2 1 1 4 1 1 1 6 6 1 1 1 1 1 1 1 1

470W209580 470W283105 470W283105 470W284108

1 1 2 1

1 1 2 1

8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23

24 25 26 27 28 29 30 31

32 33 34 35 36 37

38

39

15/21

INSTRUCTIONS MANUAL – WEDA 90 Ref

Designation 2

40 41 42

43 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 79 80 81 82 83 84 85 86 87 89 90 91 92 93 94 95

Cable 4x16mm 400V Y/D start 2 Cable 4x25mm 230V+230/400V Circlip Bearing 2 Cable sleeve 4x10mm 2 Cable sleeve 4x16mm 2 Cable sleeve 4x25mm Rotor*** O-ring O-ring Seal unit cpl Oil plug Screw Wear plate Nut Distance sleeve Connection Trim washer Stop washer Nut Bearing bracket O-ring Circlip Seal holder Upper seal Holder * Holder ** O-ring Distance ring * Distance ring ** O-ring Bearing Bearing cpl Incl pos 69,71 Bearing bracket Washer Lower seal Oil bag Incl. pos 76 Seal clamp Ring for oil bag Impeller 50Hz Impeller 60Hz Washer Impeller nut Protective housing Diffusor O-ring O-ring Diffusor holder Washer Washer Trim washer Diffusor centre Spring washer Strainer Base plate Screw Impeller 50 Hz Impeller 60Hz 16/21

P/N

Qty L

Qty H

470W284108 470W208093 4700W50525 4700W61003 470W284110 470W284100 470W209584 470W368279 4700W65140 4700W65006 470W292054 470W254042 4700W75711 470W291010 4700W84213 470W294041 470W294039 470W294040 470W294038 470W294037 470W291021 4700W65031 4700W50679 470W294109 470W294107 470W294106 470W743506 470W294105 470W294112 470W743531 4700W65112 470W294111 470W294110 470W292055 470W294171 470W294108 470W293088 470W294226 470W294103 470W292043 470W292044 470W294036 470W294035 470W292065 470W291012 4700W65174 4700W65137 470W293080 4700W51181 4700W51176 470W294124 470W291014 4700W58915 470W294102 470W293091 4700W76343 470W292045 470W292046

1 1 1 1 1 1 1 1 1 2 1 2 11 1 8 1 1 10 1 1 1 1 3 1 1 1 1 2 1 1 2 2 1 1 7 1 1 1 1 1 1 1 1 1 1 1 1 1 6 8 20 1 10 1 1 6 -

1 1 1 1 1 1 1 1 1 2 1 2 11 1 8 1 1 10 1 1 1 1 3 1 1 1 1 2 1 1 2 2 1 1 7 1 1 1 1 1 1 1 1 1 1 6 8 20 10 1 1 6 1 1

INSTRUCTIONS MANUAL – WEDA 90 Ref

Designation

96 97 98 99 100 101 102 103 104 105 106 107

Diffusor Spacer Stud bolt Diffusor centre Electrode Washer Nut Flat pin Bracket Wiring diagram Short circuit Electronic unit NVB 400V 50Hz Electronic unit NVB 440V 60Hz Electronic unit NVB 220V 50Hz Electronic unit NVB 240V 60Hz 108 Time relay 220-500V 110 Time relay Y9a 400V 111 Y/D Start cpl 400V 113 Over current relay 114 Bracket 115 Contactor See below 116 Coil See page below 117 Over current relay 220/440V60Hz Over current relay 500V 50Hz Over current relay 230/400V 50Hz and 440/500V60Hz 118 Short circuit 119 Bracket 120 Wiring diagram Wiring diagram Wiring diagram Wiring diagram 220V-3-60Hz 122 Oil 2 l 122 Oil 2 l * Pumps with manufacturing N° below 1971 . ** Pumps with manufacturing N° above 2000 . *** Pumps with manufacturing N° above 2004 .

P/N

Qty L

Qty H

470W291016 470W294191 4700W69656 470W291018 470W208106 470W209673 4700W84205 4700W50331 470W209672 470W209865 470W209674 470W209805 470W367186 470W367192 470W367193 470W743509 470W209783 470W292069 470W299593 470W292061 470W294155 470W743517 470W743549 470W209928 470W214871 470W740049 470W740276 470W740277 470W368264 4700W60015 4700W60015

1 2 4 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 x x

1 4 4 1 1 1 1 1 1 1 1 1 1 1 1 1 1 x x

STATOR and CONTACTOR Part Numbers Power supply

Stator

Contactor complete

Coil for contactor

Stator Unit (28 + 30)

220V – 3 – 60Hz

470W368285

470W368248

470W368265

-

380-400V - 3 - 50Hz

470W368289

470W208125

470W209771

470W137951

*415V – 3 – 50Hz

470W368291

470W208126

470W209772

470W368283

440-460V - 3 - 60Hz

470W368289

470W208125

470W209771

470W137951

500V - 3 - 50Hz

470W368292

470W208127

470W209773

-

* From S/N 890438

17/21

INSTRUCTIONS MANUAL – WEDA 90

18/21

INSTRUCTIONS MANUAL – WEDA 90

WEDA90L, WEDA90H

04/01 /2010

19/21

INSTRUCTIONS MANUAL – WEDA 90

WEDA90L, WEDA90H

04 / 01 /2010

20/21

Factory address : P.O Box 63, Route de Neville, 76460 Saint Valery-en-caux, France, Tel: +33.2.35.57.07.76, Fax: +33.2.35.97.48.82 We reserve the right to change specifications without notice. Photos and illustrations do not always show standard versions of machines.

www.dynapac.com