2.5 O peration of the machine

2.5.10 Travel and reversing of the machine

The machine may be operated in the transport or operating mode. The transport or operating mode are set by the switch of the transport and operating mode (15).

The travel of the machine backwards is only possible in the transport mode.

Travel of the machine in the transport mode:

• Check that the emergency switch (1) is not activated.

• Turn the transport and operating mode (15) switch to the transport mode position (rabbit).

• Start the engine according to Chapter 2.5.8.

• Travel control in the neutral position (N). The indicator lamp (23) lights on the display.

• Set the maximum engine speed using the engine speed switch (10).

• Pull the arresting ring of the travel controller (8) up and move the travel controller forward.

• The indicator lamp (25) lights on the display.

• Before reversing, make sure the screed is not on the ground or close to the ground.

• To travel the machine backwards, operate the foot switch (48); the travel control is in the neutral position, the indicator lamp (27) will light up, then pull up the arresting ring of the travel control (8) and move the travel control backwards.

• The indicator lamp (27) lights on the display and the indicator lamp (25) will go out.

• An acoustic signals is emitted by the reversing horn when the machine travels backwards.

• The maximum travel speed forward and backward is 2,2 km/h (1,37 MPH).

• During the travel the front wheel turning angle indicator (4) checks the turning angle.

Travel of the machine in the operating mode:

• Check that the emergency switch (1) is not activated.

• Switch over the transport and operating mode switch (15) to the operating mode position (turtle).

• Set the required speed using the paving speed selector (14),

• Start the engine according to Chapter 2.5.8.

• Travel control in the neutral position (N). The indicator lamp (23) lights on the display.

• Set the maximum engine speed using the engine speed switch (10).

• Pull up the arresting ring of the travel control (8) and move the travel control forward.

• The maximum travel speed forward is 0.7 km/h (0.43 MPH).

• The machine backward travel function cannot be activated in the operating mode.

• During the travel the front wheel turning angle indicator (4) checks the turning angle.

Start the engine only from the driver’s stand! Use the alarm horn to signal the engine starting and check that nobody is endangered by starting the engine!

Caution! The machine starts moving immediately in the operating mode after the forward travel control indicator (25) lights up and the travel control (8) is moved when a speed is pre-set using the paving speed selector (14).

Jumping off the parked or moving machine is prohibited. It is forbidden to get on or off the machine when it is moving.

During the operation of the machine always observe a safe three-point contact with the footboard and the handle.

2.5 O peration of the machine

2.5.11 Stopping the machine and engine

Stopping the machine:

• Stop and brake the machine by changing the travel controller (8) to the neutral position (N). The parking brake indicator lamp (23) lights up.

• Set the engine speed switch (10) to idle speed.

• Switch over the key in the ignition box (11) to the position “0“.

• Remove the key from the ignition box (11) and disconnect the battery disconnecter.

Machine emergency stop

Activation:

• Press the emergency brake button (1).

• The machine brakes, the engine stops, material distribution on the conveyor stops, and vibration units and the screed gas heating stops.

• The battery charging indicator lamp (21), engine lubrication indicator lamp (22) and emergency brake indicator lamp (26) will light up on the display.

Deactivation:

• Pull out the emergency brake button (1) while turning it. Shift the travel controller (8) to the neutral position (N); the machine can be started again in this position.

Use only if a failure occurs when it is impossible to stop the engine with the key in the ignition box or if serious emergency occurs when it is impossible to stop the machine by moving the travel control (8) to the neutral position (N)!

Turn off the battery disconnecter when shutting down the machine.

When the machine is put out of operation, protect the dashboard and the engine compartment from unauthorized access of others by locking the dashboard cover and the engine bonnet.

2.5.12 Machine parking

Shut down the machine on a flat and solid surface where there is no potential natural hazard (e.g. landslides, flooding).

• Stop and brake the machine by changing the travel controller (8) to the neutral position (N). The parking brake indicator lamp (23) lights up.

• Set the engine speed switch (10) to idle speed.

• Switch off the engine by switching over the key in the ignition box (11) to the position “0“.

• Remove the key in the ignition box (11) and close the cap of the ignition box (11).

• Turn off the battery disconnecter.

• Clean the machine from dirt.

• Check the whole machine and repair defects that occurred during operation.

• Lock the safety cover of the dashboard and the engine bonnets with a padlock.

Note

The padlock is not delivered in the machine equipment.

If the machine is equipped with a gas bottle, the gas bottle must be removed from the machine and stored in a special area.

Turn off the battery disconnecter when parking the machine.

When the machine is parked, protect the dashboard and the engine compartment from unauthorized access of others by locking the dashboard cover and the engine bonnet.