DOWNLOAD PDF : John Deere DB66 Planters Installation Instructions Manual (1)

*A109654E*

Individual Row Hydraulic Downforce for DB66 Planters

PREDELIVERY INSTRUCTIONS Individual Row Hydraulic Downforce (IRHD) A109654E ISSUE A0

John Deere Seeding Group North American Edition PRINTED IN U.S.A.

(ENGLISH)

Introduction Introduction IMPORTANT: Read through this instruction thoroughly and familiarize yourself with the machine before performing the procedure. Do not skip steps or perform them out of order.

NOTE: The acronym IRHD stands for: Individual Row Hydraulic Downforce.

The graphics shown in this procedure have parts removed for clarity.

Right-hand and left-hand sides are determined by facing in the direction of forward travel.

This instruction demonstrates the proper procedure for removing the existing pneumatic downforce system and installing the supplied hydraulic downforce system on the following planters.

• DB66 36 Row 56 cm (22 in) LM78752,0000631 -19-22MAR18-1/1

Instructions by Planter Model

• 1775NT— A109654A • 1795— A109654B • DB44— A109654C • DB60— A109654D • DB66— A109654E • DB80— A109654F • DB88— A109654G • DB90— A109654H • 1725— A109654I

A95278 —UN—23FEB17

Instruction Identification for the Planter Models of These Instructions

LM78752,0000654 -19-16SEP19-1/1

020320

PN=2

Introduction

A79309 —UN—15NOV13

TS1680 —UN—09DEC03

Install Retrofit Serial Number Decal

DB Series

Locate the original serial number (A) near the hitch on the planter frame.

A82412 —UN—21APR14

At the end of the retrofit process, install the new serial number decal from the retrofit kit near the original serial number decal (A) location.

Do not conceal or cover-up the original serial number decal when installing the new serial number decal. Record the new serial number in the spaces provided and give this page of information to the customer after the retrofit is finished.

In a separate and secure location, maintain an up-to-date inventory of all the product and component serial numbers.

Regularly verify that the identification plates have not been removed. Report any evidence of tampering to law enforcement agencies and order duplicate plates.

Other steps you can take: 1. Mark your planter with your own numbering system.

2. Take color photographs from several angles of each planter.

DB Series A—Serial Number

Machine Serial Number

SH27916,00002A8 -19-04NOV19-1/1

020320

PN=3

Introduction

Initial Software Instructions

A95278 —UN—23FEB17

IMPORTANT: DO NOT SKIP THIS STEP. Before proceeding with the instructions in this manual, complete the initial task required for the software payload.

Before starting the retrofit installation on the planter, place a DTAC case to request the correct software payload for the planter being retrofitted. The following information must be provided in addition to the field requirements of the DTAC case: Model:____________ Original Planter Serial Number:____________ Number of Rows and Row Spacing:____________ Drawbar or 2-point Hitch:____________

□ MaxEmerge™ 5e (ME5e) Serial Number:____________ □ ExactEmerge™ (EE) Serial Number:____________ □ Individual Row Hydraulic Downforce (IRHD) Serial Number:____________ NOTE: Reference DTAC solution 104712 for more information.

The software package takes a few days to be processed and sent out.

After all the software is available, connection to the planter at the rear diagnostic connector and programming of all the control units is possible.

Once the programming is finished, do the following procedures and enter the information into the display:

• Height sensor calibration • Gauge-wheel downforce sensor calibration • Pneumatic downforce to zero • Downforce sensors to zero • Enter the number of fertilizer sensors

The package is for updating the Planter Master Controller (PMC), Row Unit Controllers (RUC), and Electric Power Generation (EPG) system.

After the planter has been upgraded, start the download of software payload from the John Deere Custom Performance site.

Make sure to download and install the software for all the control units: Once the files for the PMC-A, PMC-B, RUC, and EPG are available, prepare to install the software for all the control units.

MaxEmerge is a trademark of Deere & Company ExactEmerge is a trademark of Deere & Company LM78752,000040E -19-19SEP19-1/1

020320

PN=4

Contents Page Page

Safety

BA33367 — Install the Priority Valve (Implement Power Generation) ....................15-17

Recognize Safety Information ............................05-1 Understand Signal Words...................................05-1 Park Machine Safely...........................................05-1 Follow Safety Instructions...................................05-2 Replace Safety Signs .........................................05-2 Work in Clean Area ............................................05-2 Avoid High-Pressure Fluids ................................05-3 Live With Safety..................................................05-3 Support Machine Properly ..................................05-3 Protect Against Noise .........................................05-4 Use Proper Tools ................................................05-4 Wear Protective Clothing....................................05-4 Use Proper Lifting Equipment.............................05-5 Precautions for Welding .....................................05-5 Welding...............................................................05-6

BA33370 — Install the Actuator Fittings.............20-1 BA33374, BA33375, BA33377 — Install the Actuator Fittings.............................20-2 BA33376 — Install the Actuator Fittings.............20-3 BA33366 — Install the Combination Valve Block.....................................................20-5 BA33393 — Install the Supply Hoses (Tractor Power Generation)............................20-7 BA33394 — Install the Supply Hoses (Planter Power Generation) .........................20-12 BA33395 — Install the Row Unit Hoses ...........20-25

General

System Startup

Face-Seal-Fitting Assembly and Installation—All Pressure Applications...........10-1 Metric Face Seal and O-Ring Stud End Fitting Torque Chart—Standard Pressures ....10-2 SAE Face Seal and O-Ring Stud End Fitting Torque Chart—Standard Pressures ....10-4 Service Recommendations for Fittings Flare-Type ......................................................10-5 Service Recommendations For SAE Series Four Bolt Flange Fittings.....................10-6 Service Recommendations for Metric Series Four Bolt Flange Fitting.......................10-7 Unified Inch Bolt and Screw Torque Values........10-8 Metric Bolt and Screw Torque Values.................10-9 Recommendations for Hydraulic Connections ..10-10

IRHD Configuration Setup ..................................25-1 Parallel Arm Setup..............................................25-3 Gauge Wheel Downforce Setup .......................25-10 Individual Row Hydraulic Downforce (IRHD) Initial Flush and Test ........................ 25-11 Valve Test (IRHD System Only)........................25-12 Valve Flush Test (IRHD System Only)..............25-13 Air Purge Test (IRHD System Only) .................25-15 Accumulator Test (IRHD System Only) ............25-16

Hoses and Fittings

Part Number Index Adapters .............................................................30-1 Connectors .........................................................30-2 Elbows ................................................................30-3 Plugs...................................................................30-7 Quick Couplers ...................................................30-8 Reducers ............................................................30-9 T-Fittings...........................................................30-10 Unions ..............................................................30-13 Brackets............................................................30-14

Row Unit Updates Depressurize the Pneumatic Downforce System .........................................15-1 Remove the Existing Pneumatic Downforce Springs.........................................15-2 Replace the Parallel Arm Hardware ...................15-3 BA33641 — Install the Actuators........................15-5 BA33646 — Install the ExactEmerge™ Row Unit Harness ..........................................15-9 BA33647 — Install the MaxEmerge™ 5e Row Unit Harness ................................... 15-11 BA32946 and BA33294 — Remove and Install the Downforce Sensor ................15-15 BA33644 — Install the Safety Decals...............15-16

Original Instructions. All information, illustrations and specifications in this manual are based on the latest information available at the time of publication.

The right is reserved to make changes at any time without notice.

COPYRIGHT © 2020 DEERE & COMPANY Moline, Illinois All rights reserved.

A John Deere ILLUSTRUCTION ™ Manual

i

020320

PN=1

Contents

ii

020320

PN=2

Safety Recognize Safety Information This is a safety-alert symbol. When you see this symbol on your machine or in this manual, be alert to the potential for personal injury.

T81389 —UN—28JUN13

Follow recommended precautions and safe operating practices.

DX,ALERT -19-29SEP98-1/1

Understand Signal Words DANGER; The signal word DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury.

TS187 —19—30SEP88

WARNING; The signal word WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION; The signal word CAUTION indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. CAUTION may also be used to alert against unsafe practices associated with events which could lead to personal injury.

A signal word—DANGER, WARNING, or CAUTION—is used with the safety-alert symbol. DANGER identifies the most serious hazards. DANGER or WARNING safety signs are located near specific hazards. General

precautions are listed on CAUTION safety signs.

CAUTION also calls attention to safety messages in this manual.

DX,SIGNAL -19-05OCT16-1/1

Park Machine Safely

• Lower all equipment to the ground.

• Stop the engine and remove the key.

• Disconnect the battery ground strap.

• Hang a "DO NOT OPERATE" tag in operator station.

TS230 —UN—24MAY89

Before working on the machine:

DX,PARK -19-04JUN90-1/1

05-1

020320

PN=7

Safety

Carefully read all safety messages in this instruction. Read the product operators manual for operating instructions and safety messages. Do not let anyone operate without instruction. (A copy of the operators manual may also be available from the Service ADVISOR™ application.)

TS201 —UN—15APR13

Follow Safety Instructions

Service ADVISOR is a trademark of Deere & Company DX,READ,INS -19-23JUN09-1/1

Replace Safety Signs

TS201 —UN—15APR13

Replace missing or damaged safety signs. See the machine operator’s manual for correct safety sign placement.

DX,SIGNS1 -19-04JUN90-1/1

Work in Clean Area

• Clean work area and machine.

• Make sure you have all necessary tools to do your job.

• Have the right parts on hand.

• Read all instructions thoroughly; do not attempt shortcuts.

T6642EJ —UN—18OCT88

Before starting a job:

DX,CLEAN -19-04JUN90-1/1

05-2

020320

PN=8

Safety

Avoid High-Pressure Fluids

X9811 —UN—23AUG88

Inspect hydraulic hoses periodically – at least once per year – for leakage, kinking, cuts, cracks, abrasion, blisters, corrosion, exposed wire braid or any other signs of wear or damage.

Replace worn or damaged hose assemblies immediately with John Deere approved replacement parts.

Escaping fluid under pressure can penetrate the skin causing serious injury.

Avoid the hazard by relieving pressure before disconnecting hydraulic or other lines. Tighten all connections before applying pressure.

Search for leaks with a piece of cardboard. Protect hands and body from high-pressure fluids.

If an accident occurs, see a doctor immediately. Any fluid injected into the skin must be surgically removed within a few hours or gangrene may result. Doctors unfamiliar

with this type of injury should reference a knowledgeable medical source. Such information is available in English from Deere & Company Medical Department in Moline, Illinois, U.S.A., by calling 1-800-822-8262 or +1 309-748-5636.

DX,FLUID -19-12OCT11-1/1

Live With Safety

TS231 —19—07OCT88

Before returning machine to customer, make sure machine is functioning properly, especially the safety systems. Install all guards and shields.

DX,LIVE -19-25SEP92-1/1

Always lower the attachment or implement to the ground before you work on the machine. If the work requires that the machine or attachment be lifted, provide secure support for them. If left in a raised position, hydraulically supported devices can settle or leak down.

Do not support the machine on cinder blocks, hollow tiles, or props that may crumble under continuous load. Do not work under a machine that is supported solely by a jack.

Follow recommended procedures in this manual.

When implements or attachments are used with a machine, always follow safety precautions listed in the implement or attachment operator's manual.

TS229 —UN—23AUG88

Support Machine Properly

DX,LOWER -19-24FEB00-1/1

05-3

020320

PN=9

Safety

There are many variables that affect the sound level range, including machine configuration, condition and maintenance level of the machine, ground surface, operating environmental, duty cycles, ambient noise, and attachments.

Exposure to loud noise can cause impairment or loss of hearing.

Always wear hearing protection. Wear a suitable hearing protective device such as earmuffs or earplugs to protect against objectionable or uncomfortable loud noises.

TS207 —UN—23AUG88

Protect Against Noise

DX,NOISE -19-03OCT17-1/1

Use Proper Tools Use tools appropriate to the work. Makeshift tools and procedures can create safety hazards.

For loosening and tightening hardware, use the correct size tools. DO NOT use U.S. measurement tools on metric fasteners. Avoid bodily injury caused by slipping wrenches.

Use only service parts meeting John Deere specifications.

TS779 —UN—08NOV89

Use power tools only to loosen threaded parts and fasteners.

DX,REPAIR -19-17FEB99-1/1

Wear Protective Clothing Wear close fitting clothing and safety equipment appropriate to the job.

Wear a suitable hearing protective device such as earmuffs or earplugs to protect against objectionable or uncomfortable loud noises.

Operating equipment safely requires the full attention of the operator. Do not wear radio or music headphones while operating machine.

TS206 —UN—15APR13

Prolonged exposure to loud noise can cause impairment or loss of hearing.

DX,WEAR -19-10SEP90-1/1

05-4

020320

PN=10

Safety

Use Proper Lifting Equipment Lifting heavy components incorrectly can cause severe injury or machine damage.

TS226 —UN—23AUG88

Follow recommended procedure for removal and installation of components in the manual.

DX,LIFT -19-04JUN90-1/1

Precautions for Welding

CAUTION: Avoid potentially toxic fumes and dust.

Hazardous fumes can be generated when paint is heated by welding, soldering, or using a torch.

Do all work outside or in a well ventilated area.

Dispose of paint and solvent properly. If you sand or grind paint, avoid breathing the dust by wearing an approved respirator. If you use solvent or paint stripper, remove with soap and water before welding. Remove solvent or paint stripper containers and other flammable material from area before welding. Allow fumes to disperse at least 15 minutes before welding or heating.

IMPORTANT: Welding on the engine is NOT ALLOWED. If welding must be performed on the machine, follow these precautions.

IMPORTANT: High currents or electrostatic discharge into electronic components from welding may cause permanent damage.

TS953 —UN—15MAY90

Remove paint before welding or heating (see Safety Section in this manual for more information on paint removal and high-pressure lines).

3. Disconnect the positive (+) battery cable(s) or open battery (+) switch if equipped.

4. Clear or move any wiring harness sections away from the welding area.

5. Welding on engine components is not allowed.

6. Never connect the welder ground to any engine component or engine driven components that may be connected to the engine.

7. After welding, reverse steps 2—3.

1. Remove paint from the area to be welded and ground cable clamp location.

2. Disconnect the negative (-) battery cable(s) or open battery (-) switch if equipped.

DX,WELDING,PRECAUTIONS -19-06DEC10-1/1

05-5

020320

PN=11

Safety

Welding CAUTION: When welding, always follow all safety precautions. Avoid fire by removing all flammable materials. When not possible, shield the flammable material; then, always post a fire guard with an adequate extinguisher.

If possible, lower the planter to the ground, before welding.

Avoid potentially toxic fumes or dust. Hazardous fumes can be generated when paint is heated.

Remove paint before welding.

If a paint stripper or solvent was used, remove it with soap and water. Remove the material containers from the area and allow fumes to disperse.

Work outside or in a well ventilated area.

IMPORTANT: When welding near electronic components such as the planter monitor (control unit), unplug all connectors and remove the control units from the planter to prevent possible damage to the microprocessors within the boxes.

When sanding or grinding paint, avoid breathing the dust by wearing an approved respirator.

OUO6045,00009A3 -19-05DEC16-1/1

05-6

020320

PN=12

General Face-Seal-Fitting Assembly and Installation—All Pressure Applications Face-Seal O-Ring to Stud End Installation

4. Remove thimble.

1. Inspect the fitting surfaces. They must be free of dirt and/or defects.

Face-Seal Straight Stud End O-Ring Installation

2. Inspect the O-ring. It must be free of damage and/or defects.

3. Lubricate O-rings using system oil, and install into groove.

4. Push O-ring into groove so O-ring is not displaced during assembly.

5. Index angle fittings and tighten by hand pressing joint together to insure O-ring remains in place.

1. Install a thimble over the fitting threads to protect the O-ring from nicks.

2. Slide the O-ring over the thimble into the turned down section of the fitting.

3. Remove thimble.

Fitting Installation 1. Install fitting by hand until snug.

2. Position adjustable fittings by unscrewing the fitting no more than one turn.

6. Tighten fitting or nut to torque value shown on the chart per dash size stamped on the fitting. DO NOT allow hoses to twist when tightening fittings.

3. Apply assembly torque per table.

Face-Seal Adjustable Stud End O-Ring Installation

Assembly Torque

1. Back off the lock nut and washer to full exposed turned down section of the fitting.

1. Use one wrench to hold the connector body and one wrench to tighten nut.

2. Install a thimble over the fitting threads to protect the O-ring from nicks.

2. For a hydraulic hose, it may be necessary to use three wrenches to prevent twist; one on the connector body, one on the nut, and one on the body of the hose fitting.

3. Slide the O-ring over the thimble into the turned down section of the fitting.

BB83525,00002A1 -19-09MAR17-1/1

10-1

020320

PN=13

General

Metric Face Seal and O-Ring Stud End Fitting Torque Chart—Standard Pressures N79757 —UN—13FEB08

H

G

I

F

C

G A

A—Stud Straight and Tube Nut B—Bulkhead Union and Bulkhead Lock Nut

B

E

F D E—Port Plug F— Stud End G—Tube Nut H—Swivel Nut

C—90° Swivel Elbow and Tube Nut D—90° Adjustable Stud Elbow

I— Lock Nut

Metric Face Seal and O-Ring Stud End Fitting Torque Chart—Standard Pressure-Below 27.6 MPA (4000 psi) Nominal Tube OD Hose ID Metric Tube OD

Inch Tube OD

mm

Dash Size

in

4

-2

5

Bulkhead Jam Nut TorqueA

O-Ring Face Seal/ Tube Swivel Nut Thread Size

Swivel Nut Hex Size

Tube Nut and Swivel Nut Torque

Jam Nut Hex Size

Jam Nut Torque

mm

in

mm

N· m

lb· ft

mm

N· m

0.1 25

3.18

—

—

—

—

—

-3

0.1 88

4.76

—

—

—

—

6

-4

0.2 50

6.35

9/16-18

17

16

8

-5

0.3 12

7.92

—

—

10

-6

0.3 75

9.53

11/16-1 6

12

-8

0.5 00

12.7 0

16

-1 0

0.6 25

20

-1 2

22

O-Ring Straight, Adjustable, and External Port Plug Stud EndsA Thread Size

Straight Hex SizeB

Adj Lock Nut Hex Size

Steel or Gray Iron Torque

Aluminum or Brass TorqueC

lb·ft

mm

mm

mm

N· m

lb·ft

N· m

lb·ft

—

—

M8 X 1

12

12

8

6

5

4

—

—

—

M10 X 1

14

14

15

11

10

7

12

22

32

24

M12 X 1.5

17

17

25

18

17

12

—

—

—

—

—

M14 X 1.5

19

19

40

30

27

20

22

24

18

27

42

31

M16 X 1.5

22

22

45

33

30

22

13/16-1 6

24

50

37

30

93

69

M18 X 1.5

24

24

50

37

33

25

15.8 8

1-14

30

69

51

36

118

87

M22 X 1.5

27

27

69

51

46

34

0.7 50

19.0 5

1-3/1 6-12

36

102

75

41

17 5

12 9

M27 X 2

32

32

100

74

67

49

-1 4

0.8 75

22.2 3

1-3/1 6-12

36

102

75

41

17 5

12 9

M30 X 2

36

36

130

96

87

64

25

-1 6

1.0 00

25.4 0

1-7/1 6-12

41

142

10 5

46

24 7

18 2

M33 X 2

41

41

160

118

10 7

79

28

—

—

—

—

—

—

—

—

—

—

M38 x 2

46

46

176

130

117

87

32

-2 0

1.2 50

31.7 5

1-11/1 6-12

50

190

14 0

50

32 8

24 2

M42 X 2

50

50

210

155

14 0

103

38

-2 4

1.5 00

38.1 0

2-12

60

217

16 0

60

37 4

27 6

M48 X 2

55

55

260

192

17 3

128

50

-3 2

2.0 00

50.8 0

—

—

—

—

—

—

—

M60 X 2

65

65

315

232

21 0

155

A

Tolerance is plus 15%, minus 20% of mean tightening torque unless otherwise specified.

Continued on next page

10-2

SH27916,00002AA -19-18NOV19-1/2

020320

PN=14

General B

The straight hex key wrench sizes listed apply to connectors only and may not be the same as the corresponding plug of the same thread size.

C

These torques were established using steel plated connectors in aluminum and brass.

SH27916,00002AA -19-18NOV19-2/2

10-3

020320

PN=15

General

SAE Face Seal and O-Ring Stud End Fitting Torque Chart—Standard Pressures N79757 —UN—13FEB08

H

G

I

F

C

G A

A—Stud Straight and Tube Nut B—Bulkhead Union and Bulkhead Lock Nut

B

E

F D

C—90° Swivel Elbow and Tube Nut D—90° Adjustable Stud Elbow

E—Port Plug F— Stud End G—Tube Nut H—Swivel Nut

I— Lock Nut

SAE Face Seal and O-Ring Stud End Fitting Torque Chart—Standard Pressure-Below 27.6 MPA (4000 psi) Nominal Tube OD Hose ID Metric Tube OD

O-Ring Face Seal/ Tube Swivel Nut

Inch Tube OD

Thread Size

Swivel Nut Hex Size

Tube Nut and Swivel Nut Torque

mm

Dash Size

in

mm

in

in

N· m

lb· ft

5

-3

0.188

4.78

—

—

—

—

6

-4

0.250

6.35

9/16-18

11/16

1 6

8

-5

0.312

7.92

—

—

10

-6

0.375

9.53

11/16-16

12

-8

0.500

12.70

16

-10

0.625

20

-12

22

Bulkhead Jam Nut TorqueA

O-Ring Straight, Adjustable, and External Port Plug Stud EndsA

Jam Nut Hex Size

Thread Size

Straight Hex SizeB

Adj Lock Nut Hex Size

Steel or Gray Iron Torque

Aluminum or Brass TorqueC

Jam Nut Torque

N· m

lb· ft

in

in

in

N·m

lb·ft

N·m

lb· ft

—

—

—

3/8-24

5/8

9/16

12

9

8

6

12

13/1 6

3 2

2 4

7/16-20

5/8

5/8

16

12

11

8

—

—

—

—

—

1/2-20

3/4

11/16

24

18

16

12

13/16

2 4

18

1

4 2

3 1

9/16-18

3/4

3/4

37

27

25

18

13/16-1 6

15/16

5 0

37

1-1/8

9 3

6 9

3/4-16

7/8

15/16

50

37

33

25

15.88

1-14

1-1/8

6 9

51

1-5/ 16

11 8

8 7

7/8-14

1-1/16

1-1/1 6

69

51

46

34

0.750

19.05

1-3/16-1 2

1-3/8

1 0 2

75

1-1/2

1 7 5

1 2 9

1-1/16-12

1-1/4

1-3/8

102

75

68

50

-14

0.875

22.23

1-3/16-1 2

—

1 0 2

75

—

1 7 5

1 2 9

1-3/16-12

1-3/8

1-1/2

122

90

81

60

25

-16

1.000

25.40

1-7/16-1 2

1-5/8

1 4 2

10 5

1-3/4

2 4 7

1 8 2

1-5/16-12

1-1/2

1-5/8

142

105

95

70

32

-20

1.25

31.75

1-11/1 6-12

1-7/8

1 9 0

14 0

2

3 2 8

2 4 2

1-5/8-12

1-3/4

1-7/8

190

140

127

93

38

-24

1.50

38.10

2-12

2-1/4

2 1 7

16 0

2-3/8

3 7 4

2 7 6

1-7/8-12

2-1/8

2-1/8

217

160

145

10 7

50.8

-32

2.000

50.80

—

—

—

—

—

—

—

2-1/2-12

2-3/4

2-3/4

311

229

207

15 3

A

Tolerance is plus 15%, minus 20% of mean tightening torque unless otherwise specified.

B

The straight hex key wrench sizes listed apply to connectors only and may not be the same as the corresponding plug of the same thread size.

C

These torques were established using steel plated connectors in aluminum and brass.

SH27916,00002A9 -19-18NOV19-1/1

10-4

020320

PN=16

General

Service Recommendations For Flare-Type Tube Fittings

4. To prevent twisting the tubes, use two wrenches.

Place one wrench on the connector body and with the second, tighten the swivel nut to the torque shown in this chart.

1. Check flare and flare seat for defects that cause leakage.

2. Align tube with fitting before tightening.

3. Lubricate connection and hand tighten swivel nut until snug.

Tube Size OD

Nut Size Across Flats

Torque Value a

Recommended Turns To Tighten (After Finger Tightening)

(in)

(in)

N·m (lb·ft)

(Flats)

(Turns)

3/16

7/16

8 (6)

1

1/6

1/4

9/16

12 (9)

1

1/6

5/16

5/8

16 (12)

1

1/6

3/8

11/16

24 (18)

1

1/6

1/2

7/8

46 (34)

1

1/6

5/8

1

62 (46)

1

1/6

3/4

1-1/4

102 (75)

3/4

1/8

7/8

1-3/8

122 (90)

3/4

1/8

a

The torque values shown are based on lubricated fittings.

AG,OUOMX005,246 -19-19JAN16-1/1

10-5

020320

PN=17

General

T6890BB —UN—15APR13

Service Recommendations For SAE Series Four Bolt Flange Fittings

A—Sealing Surface B—Split Flange

C—Pinched O-ring D—Single Piece Flange

1. Clean sealing surfaces (A). Inspect. Scratches cause leaks. Roughness causes seal wear. Out-of-flat causes seal extrusion. If defects cannot be polished out, replace component.

2. Install O-ring (and backup washer if necessary) into groove using petroleum jelly to hold it in place.

3. Split flange: Loosely assemble split flange (B) halves. Make sure that split is centrally located and perpendicular to port. Hand tighten cap screws to hold parts in place. Do not pinch O-ring (C).

4. Single piece flange (D): Place hydraulic line in center of flange and install cap screws. Flange must be centrally located on port. Hand tighten cap screws to hold flange in place. Do not pinch O-ring.

5. Tighten one cap screw, then tighten the diagonally opposite cap screw. Tighten two remaining cap screws.

Tighten all cap screws as specified in the chart below.

DO NOT use air wrenches. DO NOT tighten one cap screw fully before tightening the others. DO NOT over tighten.

TORQUE CHART N·m Nominal Flange Size

Cap Screw Size

1/2

lb·ft

Min

Max

Min

Max

5/16-18 UNC

20

31

15

23

3/4

3/8-16 UNC

28

54

21

40

1

3/8-16 UNC

37

54

27

40

1-1/4

7/16-14 UNC

47

85

35

63

1-1/2

1/2-13 UNC

62

131

46

97

2

1/2-13 UNC

73

131

54

97

2-1/2

1/2-13 UNC

107

131

79

97

3

5/8-11 UNC

158

264

117

195

3-1/2

5/8-11 UNC

158

264

117

195

4

5/8-11 UNC

158

264

117

195

5

5/8-11 UNC

158

264

117

195

BB83525,00001BA -19-02SEP15-1/1

10-6

020320

PN=18

General

T6890BB —UN—15APR13

Service Recommendations for Metric Series Four Bolt Flange Fitting

A—Sealing Surface B—Split Flange

C—Pinched O-Ring D—Single Piece Flange

1. Clean sealing surfaces (A). Inspect. Scratches cause leaks. Roughness causes seal wear. Out-of-flat causes seal extrusion. If defects cannot be polished out, replace component.

DO NOT use air wrenches. DO NOT tighten one cap screw fully before tightening the others. DO NOT over tighten.

TORQUE CHARTa

2. Install the correct O-ring (and backup washer if required) into groove using petroleum jelly to hold it in place.

b

3. Split flange: Loosely assemble split flange (B) halves.

Make sure split is centrally located and perpendicular to the port. Hand tighten cap screws to hold parts in place. Do not pinch O-ring (C).

4. Single piece flange (D): Place hydraulic line in center of flange and install four cap screws. Flange must be centrally located on port. Hand tighten cap screws to hold flange in place. Do not pinch O-ring.

5. After components are properly positioned and cap screws are hand tightened, tighten one cap screw, then tighten the diagonally opposite cap screw.

Tighten two remaining cap screws. Tighten all cap screws as specified in the chart below.

Thread

N·m

lb-ft

M6

12

9

M8

30

22

M10

57

42

M12

95

70

M14

157

116

M16

217

160

M18

334

246

M20

421

318

a

Tolerance ± 10%. The torques given are enough for the given size connection with the recommended working pressure. Increasing cap screw torque beyond these amounts will result in flange and cap screw bending and connection failures. b Metric standard thread.

NM95233,000021D -19-11MAR14-1/1

10-7

020320

PN=19

General

Unified Inch Bolt and Screw Torque Values TS1671 —UN—01MAY03

SAE Grade 1a Bolt or Screw Size

1/4

Hex Head

c

SAE Grade 2b

Flange Headd

Hex Head

c

SAE Grade 5, 5.1 or 5.2

Flange Headd

c

Hex Head

Flange Headd

SAE Grade 8 or 8.2 Hex Headc

Flange Headd

N·m

lb·in

N·m

lb·in

N·m

lb·in

N·m

lb·in

N·m

lb·in

N·m

lb·in

N·m

lb·in

N·m

lb·in

3.1

27.3

3.2

28.4

5.1

45.5

5.3

47.3

7.9

70.2

8.3

73.1

11.2

99.2

11.6

103

N·m

lb·ft

N·m

lb·ft

22.2

16.4

23.7

17.5

5/16

6.1

54.1

6.5

57.7

10.2

90.2

10.9

96.2

15.7 N·m

lb·ft

N·m

lb·ft

3/8

10.5

93.6

11.5

102

17.6

156

19.2

170

27.3

20.1

29.7

21.9

38.5

28.4

41.9

30.9

N·m

lb·ft

N·m

lb·ft

27.8

20.5

30.6

22.6

43

31.7

47.3

34.9

60.6

44.7

66.8

49.3

7/16

16.7 N·m

1/2

25.9

9/16

36.7

5/8

51

3/4

89.5

7/8

144

1

216

1-1/8

148

139

16.8

149

18.4

163

lb·ft

N·m

lb·ft

19.1

28.2

20.8

43.1

31.8

47

34.7

66.6

49.1

72.8

53.7

94

69.3

103

75.8

27.1

40.5

29.9

61.1

45.1

67.5

49.8

94.6

69.8

104

77

134

98.5

148

109

37.6

55.9

41.2

85

62.7

93.1

68.7

131

96.9

144

106

186

137

203

150

66

98

72.3

149

110

164

121

230

170

252

186

325

240

357

263

106

157

116

144

106

157

116

370

273

405

299

522

385

572

422

159

236

174

216

159

236

174

556

410

609

449

785

579

860

634

305

225

335

247

305

225

335

247

685

505

751

554

1110

819

1218

898

1-1/4

427

315

469

346

427

315

469

346

957

706

1051

775

1552

1145

1703

1256

1-3/8

564

416

618

456

564

416

618

456

1264

932

1386

1022

2050

1512

2248

1658

1-1/2

743

548

815

601

743

548

815

601

1665

1228

1826

1347

2699

1991

2962

2185

The nominal torque values listed are for general use only with the assumed wrenching accuracy of 20%, such as a manual torque wrench.

DO NOT use these values if a different torque value or tightening procedure is given for a specific application.

For lock nuts, for stainless steel fasteners, or for nuts on U-bolts, see the tightening instructions for the specific application.

Replace fasteners with the same or higher property class. If higher property class fasteners are used, tighten these to the strength of the original.

• Make sure that fastener threads are clean.

• Apply a thin coat of Hy-Gard™ or equivalent oil under the head and on the threads of the fastener, as shown in the following image.

• Be conservative with the amount of oil to reduce the potential for hydraulic lockup in blind holes due to excessive oil.

• Properly start thread engagement.

TS1741 —UN—22MAY18

a

Grade 1 applies for hex cap screws over 6 in (152 mm) long, and for all other types of bolts and screws of any length.

Grade 2 applies for hex cap screws (not hex bolts) up to 6 in (152 mm) long. c Hex head column values are valid for ISO 4014 and ISO 4017 hex head, ISO 4162 hex socket head, and ISO 4032 hex nuts. d Hex flange column values are valid for ASME B18.2.3.9M, ISO 4161, or EN 1665 hex flange products.

b

DX,TORQ1 -19-30MAY18-1/1

10-8

020320

PN=20

General

Metric Bolt and Screw Torque Values TS1742 —UN—31MAY18

4.8

8.8

9.8

10.9

12.9

4.8

8.8

9.8

10.9

12.9

Class 4.8 Bolt or Screw Size

M6

Hex Head

a

Class 8.8 or 9.8

Flange Headb

Hex Head

a

Class 10.9

Flange Headb

a

Hex Head

Class 12.9

Flange Headb

Hex Heada

Flange Headb

N·m

lb·in

N·m

lb·in

N·m

lb·in

N·m

lb·in

N·m

lb·in

N·m

lb·in

N·m

lb·in

N·m

lb·in

3.6

31.9

3.9

34.5

6.7

59.3

7.3

64.6

9.8

86.7

10.8

95.6

11.5

102

12.6

112

N·m

lb·ft

N·m

lb·ft

N·m

lb·ft

N·m

lb·ft

23.8

17.6

25.9

19.1

27.8

20.5

30.3

22.3

M8

8.6

76.1

9.4

83.2

16.2

143

17.6

156

N·m

lb·ft

N·m

lb·ft

N·m

lb·ft

M10

16.9

150

18.4

13.6

31.9

23.5

34.7

25.6

46.8

34.5

51

37.6

55

40.6

60

44.3

N·m

lb·ft

M12

—

—

—

—

55

40.6

61

45

81

59.7

89

65.6

95

70.1

105

77.4

M14

—

—

—

—

87

64.2

96

70.8

128

94.4

141

104

150

111

165

122

M16

—

—

—

—

135

99.6

149

110

198

146

219

162

232

171

257

190

M18

—

—

—

—

193

142

214

158

275

203

304

224

322

245

356

263

M20

—

—

—

—

272

201

301

222

387

285

428

316

453

334

501

370

M22

—

—

—

—

365

263

405

299

520

384

576

425

608

448

674

497

M24

—

—

—

—

468

345

518

382

666

491

738

544

780

575

864

637

M27

—

—

—

—

683

504

758

559

973

718

1080

797

1139

840

1263

932

M30

—

—

—

—

932

687

1029

759

1327

979

1466

1081

1553

1145

1715

1265

M33

—

—

—

—

1258

928

1398

1031

1788

1319

1986

1465

2092

1543

2324

1714

M36

—

—

—

—

1617

1193

1789

1319

2303

1699

2548

1879

2695

1988

2982

2199

The nominal torque values listed are for general use only with the assumed wrenching accuracy of 20%, such as a manual torque wrench.

DO NOT use these values if a different torque value or tightening procedure is given for a specific application.

For lock nuts, for stainless steel fasteners, or for nuts on U-bolts, see the tightening instructions for the specific application.

Replace fasteners with the same or higher property class. If higher property class fasteners are used, tighten these to the strength of the original.

• Make sure that fastener threads are clean.

• Apply a thin coat of Hy-Gard™ or equivalent oil under the head and on the threads of the fastener, as shown in the following image.

• Be conservative with the amount of oil to reduce the potential for hydraulic lockup in blind holes due to excessive oil.

• Properly start thread engagement.

TS1741 —UN—22MAY18

a

Hex head column values are valid for ISO 4014 and ISO 4017 hex head, ISO 4162 hex socket head, and ISO 4032 hex nuts.

Hex flange column values are valid for ASME B18.2.3.9M, ISO 4161, or EN 1665 hex flange products.

b

DX,TORQ2 -19-30MAY18-1/1

10-9

020320

PN=21

General

A94532 —UN—25SEP18

Recommendations for Hydraulic Connections The extend (A) and retract (B) symbols are on the tractor selective control valve (SCV).

Refer to the tractor Operator's Manual for specific hydraulic operational details.

Each time the implement hydraulics are connected to a tractor, the operator must do the following in order: 1. Use the bypass hose to flush the hydraulic hoses and perform the air purge test in the SeedStar™ Operator’s Manual.

2. After the air purge test is finished, perform the valve flush test in the SeedStar™ Operator’s Manual on the IRHD system.

A96251 —UN—18APR17

Tractor Valves

CAUTION: Avoid injury due to hydraulic hose failure. Inspect the hoses regularly.

Replace damaged hoses.

IMPORTANT: Avoid motor seal damage. Connect the case drain hose before any other hose.

Connect return hoses for hydraulic motors to a tractor extend (A) SCV.

Extend and Retract Lever Position

A82587 —UN—15MAY14

To turn off the hydraulic motors, move the tractor SCV to the float (not neutral) position.

NOTE: Functions connected to power beyond are active when the tractor engine is running. Port locations for pressure, return, and load sense vary by tractor model. (See the tractor Operator’s Manual for additional information.)

NOTE: Each vacuum blower must be connected to a separate SCV when using vacuum automation.

When not using the vacuum automation and the vacuum blower is connected to the power beyond circuit, use in-line flow control valves.

Float Lever Position A—Extend

9R Tractors (up to model year 2014)

B—Retract

9R Tractors (model year 2014 and up)

When attaching the implement to a tractor with dual hydraulic pumps, connect as many of the blowers as possible to the high flow pump.

The hydraulic system uses two hydraulic pumps providing up to 295 L/min (78 gal/min) of hydraulic flow. SCVs I, II, and III are powered by a pump providing 182 L/min (48 gal/min) of hydraulic flow. SCVs IV and V are powered by a pump providing 114 L/min (30 gal/min) of hydraulic flow.

The hydraulic system uses two hydraulic pumps providing up to 435 L/min (115 gal/min) of hydraulic flow. SCVs I, II, III, IV, and V are powered by a pump providing 218 L/min (57.5 gal/min) of hydraulic flow.

Hose Connections for Non-Fold Assist Machines SCV Symbol

Extend (A)

Function Settings for John Deere Tractors

Hose Tag

Implement Function

Flow

“Case Drain”

Hydraulic Motor Return (Connect case drain before any other hose.)

Non-Pressurized Return

“Lift Press”

CCS™ Activate Plant Frame Lift Wing Wheels Lift

“Lift Ret”

CCS™ Deactivate Plant Frame Lower Wing Wheel Lower

Detent (time)

3—10 seconds depending on the target lift height.

Adjust for the preferred raise and lower rate.

Retract (B)

Continuous “C” Continued on next page

10-10

CR53390,0000161 -19-24JUL19-1/3

020320

PN=22

General Hose Connections for Non-Fold Assist Machines SCV Symbol

Extend (A)

Hose Tag

Implement Function

“Mark/Fold”

Hitch Latch Tongue Lift Transport Frame Lift Fold Independent Marker Raise (if equipped)

Retract (B)

“Mark/Fold Ret”

Flow

Detent (time)

Start at 5 and adjust as necessary

10 seconds or as required for full extend and retract.

Start at 3 and adjust as necessary.

Do Not Use

When using vacuum automation, set flow at 7.

During manual vacuum operation, set flow at 4 and adjust as necessary.

Continuous “C”

Hitch Unlatch Tongue Lower Transport Frame Lower Unfold Independent Marker Lower (if equipped)

Extend (A)

“Press”

Rear Steer Left

Retract (B)

“Ret”

Rear Steer Right

Extend (A)

“Vac Ret”

Vacuum, Hydraulic Return

Retract (B)

“Vac Press”

Vacuum, Activate

Float

Function Settings for John Deere Tractors

Vacuum, Deactivate

Power Beyond Connections Hydraulic Function

Tag Color

Tractor Port

Red

“P” Pressure

Black

“R” Return

Implement Function Frame Weight Distribution (if equipped) Implement Power Generation (if equipped) Individual Row Hydraulic Downforce (if equipped) Fertilizer Pump with Load Sense (if equipped) a

NOTE: Do not connect hoses with power beyond couplers to an SCV.

Power Beyond Orange

“LS” Load Sense

If the IRHD is the only function on the power beyond, it does not have a load sense hose. If the IRHD is the only power beyond function, an SCV must be set to maximum flow and in the continuous detent position.

Each time the implement hydraulics are connected to a tractor, the operator must use the bypass hose to flush the hydraulic hoses when performing the air purge and valve flush tests.

a

On tractors with separate SCVs for high and low volume, connect to the high volume pump.

CCS™ control valve is used to control the CCS™ tank pressure.

SeedStar™ system is used to control the electric drives.

Hose Connections for Fold Assist Machines SCV Symbol

Extend (A)

Function Settings for John Deere Tractors

Hose Tag

Implement Function

Flow

“Case Drain”

Hydraulic Motor Return (Connect case drain before any other hose.)

Non-Pressurized Return

“Lift Press”

CCS™ Activate Plant Frame Lift Wing Wheels Lift

“Lift Ret”

CCS™ Deactivate Plant Frame Lower Wing Wheel Lower

Detent (time)

3—10 seconds depending on the target lift height.

Adjust for the preferred raise and lower rate.

Retract (B)

Continuous “C”

Continued on next page

10-11

CR53390,0000161 -19-24JUL19-2/3

020320

PN=23

General Hose Connections for Fold Assist Machines SCV Symbol

Extend (A)

Hose Tag

Implement Function

“Mark/Fold”

Activate Fold Assist Hitch Latch Transport Frame Lift Fold Independent Marker Raise (if equipped)

Retract (B)

“Mark/Fold Ret”

Release Fold Assist Hitch Unlatch Transport Frame Lower Unfold Independent Marker Lower (if equipped)

Extend (A)

“TNG CYL Press”

Tongue Lift

Retract (B)

“TNG CYL Ret”

Tongue Lower

Extend (A)

“Press”

Rear Steer Left

Retract (B)

“Ret”

Rear Steer Right

Extend (A)

“Vac Ret”

Vacuum, Hydraulic Return

Retract (B)

“Vac Press”

Vacuum, Activate

Float

Function Settings for John Deere Tractors

Vacuum, Deactivate

Flow

Detent (time)

Start at 5 and adjust as necessary.

10 seconds or as required for full extend and retract.

Start at 5 and adjust as necessary.

10 seconds or as required for full extend and retract.

Start at 3 and adjust as necessary.

Do Not Use

When using vacuum automation, set flow at 7.

During manual vacuum operation, set flow at 4 and adjust as necessary.

Continuous “C”

Power Beyond Connections Hydraulic Function

Tag Color

Tractor Port

Red

“P” Pressure

Implement Function Frame Weight Distribution (if equipped) Implement Power Generation (if equipped) Individual Row Hydraulic Downforce (if equipped) Fertilizer Pump with Load Sense (if equipped) a

Black

“R” Return

NOTE: Do not connect hoses with power beyond couplers to an SCV.

Power Beyond Orange

“LS” Load Sense

If the IRHD is the only function on the power beyond, it does not have a load sense hose. If the IRHD is the only power beyond function, an SCV must be set to maximum flow and in the continuous detent position.

Each time the implement hydraulics are connected to a tractor, the operator must use the bypass hose to flush the hydraulic hoses when performing the air purge and valve flush tests.

a

On tractors with separate SCVs for high and low volume, connect to the high volume pump.

CCS™ control valve is used to control the CCS™ tank pressure.

SeedStar™ system is used to control the electric drives.

SeedStar is a trademark of Deere & Company CCS is a trademark of Deere & Company CR53390,0000161 -19-24JUL19-3/3

10-12

020320

PN=24

Row Unit Updates

CAUTION: Escaping fluid under pressure can penetrate the skin causing serious injury.

Avoid the hazard by relieving pressure before disconnecting hydraulic or other lines. Tighten all connections before applying pressure. Search for leaks using a piece of cardboard. Protect hands and body from high-pressure fluids.

If an accident occurs, see a doctor immediately.

Any fluid injected into the skin must be surgically removed within a few hours or gangrene can result. Doctors unfamiliar with this type of injury, call the Deere & Company Medical Department in Moline, Illinois, or another knowledgeable medical source.

TS230 —UN—24MAY89

X9811 —UN—23AUG88

Depressurize the Pneumatic Downforce System

1. Park the planter on a flat level surface.

2. Stop the engine and turn the key switch to the OFF position.

3. Turn the key switch to the ON position, DO NOT start the engine. Place the SCV lever in the float position.

Place the frame control box in the PLANT position.

Activate all the frame functions in each direction.

4. Place the frame control box in the TRANS position.

Activate all the frame functions in each direction.

LM78752,0000494 -19-31JAN18-1/3

NOTE: The location and orientation of the air reservoir varies based on the planter model. This procedure is similar for all models.

A86699 —UN—09JUN15

5. Release all of the air pressure from the pneumatic system using the following procedure: 6. On the SeedStar™ monitor, reduce the downforce pressure to 66 N (15 lb).

7. Release the residual air pressure from the air springs by pressing the manual override button (A).

A—Manual Override Button

Rear Side of Valve Stack Shown

SeedStar is a trademark of Deere & Company Continued on next page

15-1

LM78752,0000494 -19-31JAN18-2/3

020320

PN=25

Row Unit Updates

8. Release the reservoir air pressure by opening the drain valve (A).

A68065 —UN—07JUL10

A—Drain Valve

LM78752,0000494 -19-31JAN18-3/3

Remove the Existing Pneumatic Downforce Springs 1. Disconnect the hoses (B) from the fitting (A).

B—Hoses A92495 —UN—26SEP16

A—Fitting

LM78752,0000495 -19-31JAN18-1/3

2. Remove and discard the cap screws (A), lock nuts (B), and the spacers (C).

C—Spacer (2 used)

A92648 —UN—05OCT16

A—Cap Screw (3 used) B—Lock Nut (3 used)

Continued on next page

15-2

LM78752,0000495 -19-31JAN18-2/3

020320

PN=26

Row Unit Updates

3. Remove and discard the cap screws (A and B), lock nuts (C and D), and the air spring (E).

4. Remove and discard all of the pneumatic air lines and fittings.

A—Cap Screw B—Cap Screw (2 used) C—Lock Nut (2 used)

A92560 —UN—27SEP16

5. Repeat on the remaining row units.

D—Lock Nut E—Air Spring

LM78752,0000495 -19-31JAN18-3/3

A93746 —UN—16NOV16

Replace the Parallel Arm Hardware

A—Cap Screw

B—Nut

1. Remove and discard the existing cap screws (A) and nuts (B).

CAUTION: DO NOT remove all of the hardware at once. Doing so causes the row unit to fall.

Replace one set of hardware at a time.

NOTE: Retain the existing washers and spacers for reuse.

Continued on next page

15-3

LM78752,0000496 -19-31OCT19-1/2

020320

PN=27

A93747 —UN—16NOV16

Row Unit Updates

A—Cap Screw, M16 x 45 (4 used) B—Nut, M16 (4 used) D—Nut, M16 (4 used) C—Cap Screw, M16 x 55 (4 used)

NOTE: If an electric drive kit was ordered along with the IRHD kit, use the row unit hardware provided in the electric drive kit.

Specification Nuts (B and D)—Torque (dry).............................................................................................250 N·m (184 lb·ft)

NOTE: Install the previously retained washers and spacers.

3. Repeat on the remaining row units.

2. Install the cap screws (A and C) and nuts (B and D).

Tighten to specification.

LM78752,0000496 -19-31OCT19-2/2

15-4

020320

PN=28

Row Unit Updates

BA33641 — Install the Actuators NOTE: Use the hardware kit BA33360.

Parts List Part Number

Description

Quantity

AA96048

Actuator

1

A105601

Upper Bracket

1

A105603

Lower Bracket

1

AA92059

Flag Pin

2

24M7053

Washer, 17 mm

2

11M7021

Cotter Pin

2

19M7658

Cap Screw, M10 x 50

2

19M7396

Cap Screw, M16 x 45

1

14M7274

Nut, M10

2

A31869

Lock Nut, M16

1

19M7638

a

Cap Screw, M10 x 130

2

19M6824

Cap Screw, M16 x 120a

1

24M7239

Washer, 11 mm a

2

19M7362

Cap Screw, M12 x 55

2

19M8348

Cap Screw, M12 x 65

2

A55881

Bushing, 13 mm

4

A31867

Lock Nut, M12

4

a

Used with long parallel arms and spacer.

A—Upper Bracket B—Actuator

C—Lower Bracket D—Flag Pin (2 used)

A98275 —UN—10OCT17

A98274 —UN—10OCT17

Assemble Actuator

E—Washer, 17 mm (2 used) F— Cotter Pin (2 used)

1. Attach the upper bracket (A) and lower bracket (C) to actuator (B) using flag pins (D), washers (E), and cotter pins (F).

2. Repeat step 1 on the remaining actuators.

Continued on next page

15-5

LM78752,00005A4 -19-13JAN20-1/7

020320

PN=29

Row Unit Updates

A92561 —UN—10OCT17

Install Actuator — Regular Parallel Arms

A—Actuator D—Cap Screw, M12 x 65 (2 used) F— Nut, M10 (2 used) B—Cap Screw, M10 x 50 (2 used) E—Cap Screw, M12 x 55 (2 used) G—Lock Nut, M16 C—Cap Screw, M16 x 45 H—Lock Nut, M12 (4 used)

I— Bushing, 13 mm (4 used)

1. Gather the actuator (A), cap screws (B—E), nuts (F), lock nuts (G and H), and bushings (I).

A92563 —UN—27SEP16

A92562 —UN—27SEP16

LM78752,00005A4 -19-13JAN20-2/7

A—Cap Screw, M10 x 50 (2 used) B—Cap Screw, M16 x 45

C—Nut, M10 (2 used) D—Nut, M16

NOTE: Verify that the cap screws are oriented as shown.

Nut (D)—Torque (dry)..................................................................240 N·m (175 lb·ft)

2. Install the actuator assembly on the mounting bracket using cap screws (A and B) and nuts (C and D).

Tighten to specification.

Specification Nuts (C)—Torque (dry)..................................................................80 N·m (59 lb·ft) Continued on next page

15-6

LM78752,00005A4 -19-13JAN20-3/7

020320

PN=30

A92564 —UN—10OCT17

Row Unit Updates

Top View of Row Unit A—Cap Screw, M12 x 55 (2 used) B—Cap Screw, M12 x 65 (2 used) C—Bushing, 13 mm (4 used) D—Lock Nut, M12 (4 used)

3. Attach the actuator assembly to the parallel arms using cap screws (A and B), bushings (C), and lock nuts (D). Tighten to specification.

4. Repeat on the remaining row units.

Specification Lock Nuts (D)—Torque (dry)............................................................................................. 110 N·m (81 lb·ft) Continued on next page

15-7

LM78752,00005A4 -19-13JAN20-4/7

020320

PN=31

Row Unit Updates

A98289 —UN—18OCT17

Install Actuator — Long Parallel Arms

A—Actuator D—Cap Screw, M12 x 65 (2 used) G—Lock Nut, M16 B—Cap Screw, M10 x 130 (2 used) E—Cap Screw, M12 x 55 (2 used) H—Lock Nut, M12 (4 used) C—Cap Screw, M16 x 120 F— Nut, M10 (2 used) I— Bushing, 13 mm (4 used)

NOTE: The spacer (J) was previously retained when removing the pneumatic downforce springs.

J— Spacer K—Washer, 11 mm (2 used)

1. Gather the actuator (A), cap screws (B—E), nuts (F), lock nuts (G and H), bushings (I), spacer (J), and washers (K).

A—Spacer B—Actuator Bracket C—Washer, 11 mm (2 used)

A105987 —UN—13NOV19

A105986 —UN—13NOV19

LM78752,00005A4 -19-13JAN20-5/7

D—Cap Screw, M10 x 130 (2 used) F— Nut, M10 (2 used) E—Cap Screw, M16 x 120 G—Lock Nut, M16

2. Install the actuator bracket (B) on the mounting bracket using spacer (A), washers (C), cap screws (D and E), and nuts (F and G). Tighten to specification.

Lock Nut (G)—Torque (dry).............................................................................................240 N·m (175 lb·ft)

Specification Nuts (F)—Torque (dry)..................................................................80 N·m (59 lb·ft) Continued on next page

15-8

LM78752,00005A4 -19-13JAN20-6/7

020320

PN=32

A93071 —UN—10OCT17

Row Unit Updates

Top View of Row Unit A—Cap Screw, M12 x 55 (2 used) B—Cap Screw, M12 x 65 (2 used) C—Bushing, 13 mm (4 used) D—Lock Nut, M12 (4 used)

3. Attach the actuator to the parallel arms using the supplied cap screws (A and B), bushings (C), and lock nuts (D).Tighten to specification.

4. Repeat on the remaining row units.

Specification Lock Nuts (D)—Torque (dry)............................................................................................. 110 N·m (81 lb·ft) LM78752,00005A4 -19-13JAN20-7/7

BA33646 — Install the ExactEmerge™ Row Unit Harness A

B

NOTE: If an electric drive performance upgrade was ordered with the IRHD kit, the row unit harness is not installed. Skip the removal procedure and continue on to the installation of the row unit harness.

C

NOTE: The standard row unit harness is shown. The harness varies from machine to machine.

A105984 —UN—16DEC19

Remove the Existing Row Unit Harness

1. Remove and discard the nut (A) and lock washer (B).

2. Remove the row unit harness (C) from the bracket.

A—Nut B—Lock Washer Continued on next page

15-9

C—Row Unit Harness

LM78752,00005BF -19-17DEC19-1/5

020320

PN=33

Row Unit Updates

NOTE: Disconnect all other connections, including the row unit controller.

3. Remove and discard the row unit harness (A).

A A105982 —UN—16DEC19

4. Repeat on the remaining row units.

A—Standard Row Unit Harness

LM78752,00005BF -19-17DEC19-2/5

Install the Row Unit Harness — ExactEmerge™ 1. Install the supplied ExactEmerge™ harness (A).

A A105983 —UN—16DEC19

A—ExactEmerge™ Harness (AA89548)

ExactEmerge is a trademark of Deere & Company LM78752,00005BF -19-17DEC19-3/5

2. Install the ExactEmerge™ harness (C) using the supplied nut (A) and lock washer (B). Tighten the nut (A) to specification.

A—Nut (1-1/2 in) B—Lock Washer (1-1/2 in)

A

B

C—ExactEmerge™ Harness

C

Continued on next page

15-10

A105984 —UN—16DEC19

Specification Nut (A)—Torque (dry)....................................................................85 N·m (75 lb·in)

LM78752,00005BF -19-17DEC19-4/5

020320

PN=34

Row Unit Updates

3. Connect the ExactEmerge™ harness (A) to the previously installed actuator (B).

A

4. Connect all other harnesses on the row unit.

B

A—ExactEmerge™ Harness

A105985 —UN—16DEC19

5. Repeat on the remaining row units.

B—Actuator

A

LM78752,00005BF -19-17DEC19-5/5

BA33647 — Install the MaxEmerge™ 5e Row Unit Harness A

B

NOTE: If an electric drive performance upgrade was ordered with the IRHD kit, the row unit harness is not installed. Skip the removal procedure and continue on to the installation of the row unit harness.

C

NOTE: The standard row unit harness is shown. The harness varies from machine to machine.

A105984 —UN—16DEC19

Remove the Existing Row Unit Harness

1. Remove and discard the nut (A) and lock washer (B).

2. Remove the row unit harness (C) from the bracket.

A—Nut (1-1/2 in) B—Lock Washer (1-1/2 in)

C—Row Unit Harness

LM78752,00005C0 -19-17DEC19-1/6

NOTE: Disconnect all other connections, including the row unit controller (RUC).

3. Remove and discard the row unit harness (A).

A A105982 —UN—16DEC19

4. Repeat on the remaining row units.

A—Standard Row Unit Harness

Continued on next page

15-11

LM78752,00005C0 -19-17DEC19-2/6

020320

PN=35

Row Unit Updates Install the Row Unit Harness — MaxEmerge™ 5e 1. Install the MaxEmerge™ 5e harness (A).

A

A106196 —UN—16DEC19

A—MaxEmerge™ 5e Harness (AA96753)

MaxEmerge is a trademark of Deere & Company Continued on next page

15-12

LM78752,00005C0 -19-17DEC19-3/6

020320

PN=36

Row Unit Updates

C

A105988 —UN—16DEC19

B

A106197 —UN—16DEC19

A

D

H

E

A—Nut (1-1/2 in) B—Lock Washer (1-1/2 in) C—MaxEmerge™ 5e Harness (AA96753)

D—Tie Band (2 used) E—Tie Band F— Tie Band

A106195 —UN—16DEC19

A105989 —UN—16DEC19

I

F G J

G—Connector H—Connector I— Actuator J— Tie Band

2. Install the MaxEmerge™ 5e harness (C) using the supplied nut (A) and lock washer (B). Tighten the nut (A) to specification.

5. Push the tie band (F) into the side of the actuator (I).

6. Attach the connectors (G and H).

Specification Nut (A)—Torque (dry)....................................................................85 N·m (75 lb·in)

NOTE: Attach all other connections, including the row unit controller.

7. Secure the harness with the tie band (J).

3. Push the tie bands (D) into the holes in the bracket.

4. Secure the wiring harness to the bracket using the tie band (E).

Continued on next page

15-13

LM78752,00005C0 -19-17DEC19-4/6

020320

PN=37

A98287 —UN—13OCT17

A98286 —UN—12OCT17

Row Unit Updates

DB Splitter Row Unit Shown

MaxEmerge™ 5e Row Unit A—CCS™ Hose

B—Angled Coupler

IMPORTANT: Avoid wiring harness and pressure sensor damage on the MaxEmerge™ 5e row units with regular parallel arms.

NOTE: If an angled coupler (B) is used, install the coupler angled to the right.

8. Always install the CCS™ hose (A) to the right of the harnesses and hoses.

Route the CCS™ hose away from the pressure sensor.

MaxEmerge is a trademark of Deere & Company CCS is a trademark of Deere & Company

LM78752,00005C0 -19-17DEC19-5/6

9. Secure the pneumatic hoses to the RUC bracket using the tie band (A).

10. Repeat on the remaining row units.

A98288 —UN—12OCT17

A—Tie Band

LM78752,00005C0 -19-17DEC19-6/6

15-14

020320

PN=38

Row Unit Updates

BA32946 and BA33294 — Remove and Install the Downforce Sensor

A98291 —UN—23OCT17

A98290 —UN—23OCT17

NOTE: Use BA33294 for MY14 and older machines (S.N.—755100).

Left-Hand Rear View of Row Unit

NOTE: When upgrading an ExactEmerge™ machine, the motor mounting bracket must be removed from the top of the shank in order to route the downforce sensor harness.

A98292 —UN—23OCT17

Route the downforce sensor harness along the groove on the left-hand side of the shank.

1. Remove and discard the existing walking depth gauge wheel stop, snap ring, and pin.

2. Install the downforce sensor (A) in the shank.

3. Retain the sensor with the pin (B) and snap ring (C).

Right-Hand Rear View of Row Unit

4. Retain the sensor harness using the clips (D).

5. Repeat this procedure on all of the row units. IRHD requires a downforce sensor on every row unit.

A—Downforce Sensor B—Pin

C—Snap Ring D—Clip (2 used)

ExactEmerge is a trademark of Deere & Company LM78752,00005A3 -19-13JAN20-1/1

15-15

020320

PN=39

Row Unit Updates

Rear View

A99151 —UN—23JAN18

A99150 —UN—23JAN18

BA33644 — Install the Safety Decals

Left-Hand Rear View

A99152 —UN—23JAN18

IMPORTANT: Ensure decal adhesion. Before applying new decals, clean all dirt, grease, oil, and moisture from the application area.

Surface temperature must be greater than 15°C (60°F) for best adhesion.

NOTE: For French decals: Place the decal on top of the English decal.

For Spanish decals: Place the decal next to the English decal. Both of the decals must be visible. If additional application area is not available, place the decal as close to the English decal as possible.

Right-Hand Rear View

The images in this procedure have parts removed for clarity.

A—Safety Decal (2 used)

1. Install the safety decals (A) between the last two-row units on each end of the frame.

5. Verify that the decal is securely applied.

2. Remove the paper backing from the new decal.

3. Press one edge of the new decal to the tool bar.

4. Smooth out the air pockets while slowly pressing across the decal to the opposite edge.

LM78752,0000633 -19-02MAR18-1/1

15-16

020320

PN=40

Row Unit Updates

BA33367 — Install the Priority Valve (Implement Power Generation) Parts List Description

Quantity

A107104

Plate

1

19M7784

Cap Screw, M10 x 20

2

19M7868

Cap Screw, M8 x 30

2

AA93152

Priority Valve

1

14M7298

Nut, M8

2

A98026 —UN—04DEC17

Part Number

A—Priority Valve

B—Plate C—Cap Screw, M10 x 20 (2 used)

1. Attach the priority valve (A) to the plate (B) using the cap screws (C).

Continued on next page

15-17

LM78752,0000634 -19-08AUG18-1/2

020320

PN=41

A98029 —UN—04DEC17

A98028 —UN—04DEC17

Row Unit Updates

A—Priority Valve Assembly

B—Cap Screw, M8 x 30 (2 used)

C—Nut, M8 (2 used)

2. Attach the priority valve assembly (A) using the cap screws (B) and nuts (C).

LM78752,0000634 -19-08AUG18-2/2

15-18

020320

PN=42

Hoses and Fittings BA33370 — Install the Actuator Fittings NOTE: See the Part Number Index at the end of this instruction for images of each part.

Parts List Part Number

Description

Quantity

61H1023

T-Fitting (with 9/16; 11/16; 11/16-in ports)

1

61H1160

Adapter (with 9/16; 11/16-in ports)

1

61H1030

Swivel T-Fitting (with three 11/16-in ports)

1

AA89749

Quick Coupler (11/16 in)

2

A107718

Dust Cap (1-1/8 in)

2

Row Unit Configurations

DB66 36-Row 56 cm (22 in)

6, 13, 23, 24, 30, 36

A—T-Fitting (61H1023) B—Adapter (61H1160)

C—Swivel T-Fitting (61H1030) D—Dust Cap (A107718) (2 used)

A98451 —UN—02NOV17

A98450 —UN—02NOV17

A98449 —UN—02NOV17

Row Units

A98320 —UN—02NOV17

Machine

E—Quick Coupler (AA89749) (2 used) F— Quick Coupler Assembly (2 used)

IMPORTANT: Orient the fittings as shown.

3. Install the dust cap (D) on the quick coupler (E).

1. Install the T-fitting (A) and adapter (B). Tighten to specification.

4. Install the quick coupler assemblies (F). Tighten to specification.

2. Install the swivel T-fitting (C) on the adapter (B).

Tighten to specification.

Continued on next page

20-1

LM78752,0000632 -19-29AUG18-1/2 020320

PN=43

Hoses and Fittings Swivel T-Fitting (C)—Torque (lubricated)................................................................24 N·m (18 lb·ft) Quick Coupler Assembly (F)—Torque (lubricated)................................................................24 N·m (18 lb·ft)

5. Repeat on the remaining row units.

Specification T-Fitting (A)—Torque (lubricated)....................................................................................37 N·m (27 lb·ft) Adapter (B)—Torque (lubricated)....................................................................................37 N·m (27 lb·ft)

LM78752,0000632 -19-29AUG18-2/2

BA33374, BA33375, BA33377 — Install the Actuator Fittings Parts Used in the Following Procedure Part Number

Description

61H1023

T-Fitting (with 9/16; 11/16-in ports)

1

61H1160

Adapter (with 9/16; 11/16-in ports)

1

61H1030

Swivel T-Fitting (with three 11/16-in ports)

1

Quantity

Row Unit Configurations

DB66 36-Row 56 cm (22 in)

2, 3, 4, 5, 8, 9, 10, 11, 12, 15, 16, 17, 18, 19, 20, 21, 22, 25, 26, 27, 28, 29, 32, 33, 34, 35

A—T-Fitting (61H1023)

B—Adapter (61H1160)

A98454 —UN—02NOV17

Row Units

A98453 —UN—02NOV17

Machine

C—Swivel T-Fitting (61H1030)

IMPORTANT: Orient the fittings as shown.

1. Install the T-fitting (A) and adapter (B) on the actuator.

Tighten to specification.

2. Install the swivel T-fitting (C) on the adapter (B).

Tighten to specification.

Adapter (B)—Torque (lubricated)....................................................................................37 N·m (27 lb·ft) Swivel T-Fitting (C)—Torque (lubricated)................................................................24 N·m (18 lb·ft)

3. Repeat on the remaining row units.

Specification T-Fitting (A)—Torque (lubricated)....................................................................................37 N·m (27 lb·ft) NL54298,00000ED -19-20NOV19-1/1

20-2

020320

PN=44

Hoses and Fittings

BA33376 — Install the Actuator Fittings Parts List Part Number

Description

Quantity

61H1023

T-Fitting (with 9/16; 11/16; 11/16-in ports)

1

61H1030

Swivel T-Fitting (with three 11/16-in ports)

1

61H1160

Adapter (with 9/16; 11/16-in ports)

1

61H1094

90° Swivel Elbow (with 11/16-in ports)

2

A107718

Dust Cap (1-1/8 in)

2

AA89749

Quick Coupler (11/16 in)

2

Row Unit Configurations Machine

Row Units

DB66 36-Row 56 cm (22 in)

1, 7, 14, 31

1. Install the dust caps (A) on the quick couplers (B).

B—Quick Coupler (AA89749) (2 used)

A99162 —UN—25JAN18

A—Dust Cap (A107718) (2 used)

Continued on next page

20-3

NL54298,00000EE -19-29AUG18-1/2

020320

PN=45

A—T-Fitting (61H1023) B—Adapter (61H1160)

C—Swivel T-Fitting (61H1030) D—90° Swivel Elbow (61H1094) (2 used)

IMPORTANT: Orient the fittings as shown.

2. Install the T-fitting (A) and adapter (B). Tighten to specification.

3. Install the swivel T-fitting (C) on the adapter (B).

Tighten to specification.

4. Install the 90° swivel elbows (D). Tighten to specification.

5. Install the quick coupler assemblies (E). Tighten to specification.

A98876 —UN—19JAN18 A98880 —UN—24JAN18

A98877 —UN—19JAN18

A98878 —UN—22JAN18

Hoses and Fittings

E—Quick Coupler Assembly (AA89749) (2 used)

Adapter (B)—Torque (lubricated)....................................................................................37 N·m (27 lb·ft) Swivel T-Fitting (C)—Torque (lubricated)................................................................24 N·m (18 lb·ft) 90° Swivel Elbow (D)—Torque (lubricated)................................................................24 N·m (18 lb·ft) Quick Coupler Assembly (E)—Torque (lubricated)................................................................24 N·m (18 lb·ft)

6. Repeat steps on the remaining row units.

Specification T-Fitting (A)—Torque (lubricated)....................................................................................37 N·m (27 lb·ft) NL54298,00000EE -19-29AUG18-2/2

20-4

020320

PN=46

Hoses and Fittings

BA33366 — Install the Combination Valve Block Parts List Part Number

Description

Quantity

A106145

Combination Valve Block

1

TA13467

Pressure Sensor

1

A107254

Bracket

1

19M7898

Cap Screw, M10 x 130

4

14M7274

Nut, M10

4

A68785

U-Bolt, M20 x 361

2

14M7474

Nut, M20

4

N380408

Clamp

1

1. Install the pressure sensor (A) on the combination valve block (B). Tighten to specification.

A—Pressure Sensor (TA13467)

A94495 —UN—18JAN17

Specification Pressure Sensor (A)—Torque (lubricated)................................................................37 N·m (27 lb·ft) B—Combination Valve Block (A106145)

NL54298,00000EF -19-20JAN20-1/3

NOTE: Verify that the clamp (D) is installed.

A—Combination Valve Block (A106145) B—Bracket (A107254) C—Cap Screw, M10 x 130 (19M7898) (4 used)

D—Clamp (N380408) E—Nut, M10 (14M7274) (4 used)

Continued on next page

20-5

A94496 —UN—04OCT17

2. Attach the combination valve block (A) to the bracket (B) using cap screws (C) and the supplied nuts (E).

NL54298,00000EF -19-20JAN20-2/3

020320

PN=47

A94498 —UN—19JAN17

A94497 —UN—18JAN17

Hoses and Fittings

View of Assembly Location on Frame A—Combination Valve Block Assembly

B—U-Bolt, M20 x 361 (A68785) (2 C—Nut, M20 (14M7474) (4 used) used) D—Distance, 508 mm (20 in)

3. Install the combination valve block assembly (A), at the recommended distance (D), using U-bolts (B) and nuts (C).

NL54298,00000EF -19-20JAN20-3/3

20-6

020320

PN=48

Hoses and Fittings

BA33393 — Install the Supply Hoses (Tractor Power Generation)

that the heading of this procedure exactly matches the configuration of the machine being upgraded.

NOTE: Use the fitting kit BA33619.

NOTE: A load sense hose is only necessary if the planter is equipped with planter power generation. Verify Parts List Part Number

Description

Quantity

61H1007

90° Elbow (with 1-1/16-in ports)

1

61H1163

Adapter (with 1-1/16; 1-3/16-in ports)

1

61H1174

Adapter (with 13/16; 7/8-in ports)

4

61H1175

Adapter (with 13/16; 1-1/16-in ports)

2

64H5017

Drain Plug (9/16 in)

1

AA83767

Quick Coupler (1-1/16 in)

1

AT361540

Fitting Plug (7/8 in)

1

H77698

Tie Band, 381 mm (15 in)

3

R27390

Nut (1-1/16 in)

4

R37145

45° Swivel Elbow (with 1-1/16-in ports)

2

R47876

Union (1-1/16 in)

4

RE207298

Quick Coupler (1-1/16 in)

1

AA85322

Hydraulic Hose

1

AA85323

Hydraulic Hose

1

AA87847

Hydraulic Hose

1

AA87848

Hydraulic Hose

1

AA88657

Hydraulic Hose

1

AA88658

Hydraulic Hose

1

AA89370

Hydraulic Hose

1

AA89371

Hydraulic Hose

1

A—Adapter (61H1175) (2 used) B—Adapter (61H1174) (2 used)

C—Fitting Plug (AT361540) D—Adapter (61H1163)

A94679 —UN—07FEB17

A94678 —UN—19JAN17

Install the Fittings

E—Adapter (61H1174) (2 used) F— 90° Elbow (61H1007)

Continued on next page

20-7

NL54298,00000F0 -19-31JAN20-1/11 020320

PN=49

Hoses and Fittings 1. Install the adapters (A, B, D, and E), plug (C), and 90° elbow (F). Tighten to specification.

Plug (C)—Torque (lubricated)....................................................................................69 N·m (51 lb·ft) Adapter (D)—Torque (lubricated)..................................................................................102 N·m (75 lb·ft) 90° Elbow (F)—Torque (lubricated)..................................................................................102 N·m (75 lb·ft)

Specification Adapters (A)—Torque (lubricated)..................................................................................102 N·m (75 lb·ft) Adapters (B and E)—Torque (lubricated).................................................................69 N·m (51 lb·ft)

A99200 —UN—31JAN18

A94683 —UN—20JAN17

NL54298,00000F0 -19-31JAN20-2/11

A99201 —UN—31JAN18

A94685 —UN—20JAN17

Left-Hand Bulkhead Location

Right-Hand Bulkhead Location A—Union (R47876)

B—Nut (R27390)

C—45° Swivel Elbow (R37145)

NOTE: MY12—MY14 (S.N. 745101—760100) DB planters do not have the necessary holes to install the unions as shown. To install the unions, drill 28.6 mm (1-1/4 in) holes on the wing bulkheads.

Fabricate as necessary to avoid hose damage.

Specification 45° Swivel Elbow (C)—Torque (lubricated)..............................................................102 N·m (75 lb·ft)

2. Install the union (A), nut (B), and 45° swivel elbow (C) on the left-hand and right-hand bulkheads. Tighten the 45° swivel elbow (C) to specification.

Continued on next page

20-8

NL54298,00000F0 -19-31JAN20-3/11

020320

PN=50

A94690 —UN—19JAN17

A94691 —UN—19JAN17

Hoses and Fittings

Front Bulkhead A—Union (R47876) (2 used)

Front View of Bulkhead

B—Nut (R27390) (2 used)

NOTE: MY12—MY14 (S.N. 745101—760100) DB planters do not have the necessary holes to install the unions as shown. To install the unions, drill 28.6 mm (1-1/4 in) holes on the center bulkhead.

Fabricate as necessary to avoid hose damage.

3. Install the unions (A) and nuts (B) on the front bulkhead.

NL54298,00000F0 -19-31JAN20-4/11

Install the Hoses 1. Connect the hoses (A and B). Tighten to specification.

A—Return Hose (AA89371)

A94680 —UN—19JAN17

Specification Hoses (A and B)—Torque (lubricated)..................................................................................102 N·m (75 lb·ft) B—Pressure Hose (AA89370)

NL54298,00000F0 -19-31JAN20-5/11

2. Route the hoses (A and B) along the wings.

B—Pressure Hose (AA89370)

A99202 —UN—31JAN18

A—Return Hose (AA89371)

Front View on the Center Frame Continued on next page

20-9

NL54298,00000F0 -19-31JAN20-6/11

020320

PN=51

A99204 —UN—31JAN18

A99203 —UN—31JAN18

Hoses and Fittings

Right-Hand Bulkhead A—Return Hose (AA89371)

Left-Hand Bulkhead

B—Pressure Hose (AA89370)

3. Connect the hoses (A and B). Tighten to specification.

Specification Hoses (A and B)—Torque (lubricated)..................................................................................102 N·m (75 lb·ft)

A99206 —UN—31JAN18

A99205 —UN—31JAN18

NL54298,00000F0 -19-31JAN20-7/11

Right-Hand Bulkhead A—Return Hose (AA87848)

Left-Hand Bulkhead

B—Pressure Hose (AA87847)

NOTE: Route the hoses (A and B) through the hitch tubes BEFORE connecting them to the wing bulkhead.

4. Route the hoses (A and B) through the hitch tubes.

Specification Hoses (A and B)—Torque (lubricated)..................................................................................102 N·m (75 lb·ft)

5. Connect the hoses (A and B) to the wing bulkheads.

Tighten to specification.

Continued on next page

20-10

NL54298,00000F0 -19-31JAN20-8/11

020320

PN=52

Hoses and Fittings

6. Connect the hoses (A and B) to the front bulkhead.

Tighten to specification.

A—Return Hose (AA87848)

A94692 —UN—19JAN17

Specification Hoses (A and B)—Torque (lubricated)..................................................................................102 N·m (75 lb·ft) B—Pressure Hose (AA87847)

Rear View of Front Bulkhead NL54298,00000F0 -19-31JAN20-9/11

7. Connect the hoses (A and B). Tighten to specification.

A—Return Hose (AA85323)

A94693 —UN—19JAN17

Specification Hoses (A and B)—Torque (lubricated)..................................................................................102 N·m (75 lb·ft) B—Pressure Hose (AA85322)

Front View of the Hitch NL54298,00000F0 -19-31JAN20-10/11

8. Connect the hoses (A and B). Tighten to specification.

A—Pressure Hose (AA88657)

A94694 —UN—19JAN17

Specification Hoses (A and B)—Torque (lubricated)....................................................................................50 N·m (37 lb·ft) B—Return Hose (AA88658)

Valve Block on the Center Frame NL54298,00000F0 -19-31JAN20-11/11

20-11

020320

PN=53

Hoses and Fittings

BA33394 — Install the Supply Hoses (Planter Power Generation)

that the heading of this procedure exactly matches the configuration of the machine being upgraded.

NOTE: Use the fitting kit BA33628.

NOTE: A load sense hose is only necessary if the planter is equipped with planter power generation. Verify Parts List Part Number

Description

Quantity

61H1007

90° Elbow (with 1-1/16-in ports)

1

61H1163

Adapter (with 1-1/16; 1-3/16-in ports)

1

61H1174

Adapter (with 13/16; 7/8-in ports)

4

61H1175

Adapter (with 13/16; 1-1/16-in ports)

2

AA83767

Quick Coupler (1-1/16 in)

1

64H5017

Drain Plug (9/16 in)

1

H77698

Tie Band, 381 mm (15 in)

3

R27390

Nut (1-1/16 in)

4

R37145

45° Swivel Elbow (with 1-1/16-in ports)

2

R47876

Union (1-1/16 in)

4

RE207298

Quick Coupler (1-1/16 in)

1

61H1052

90° Elbow (with 1-5/16-in ports)

1

61H1162

Adapter (with 7/8; 1-in ports)

1

61H1147

Fitting Plug (13/16 in)

1

AN33434

Swivel T-Fitting (with three 3/4-in ports)

1

14H847

Nut (7/8 in)

2

R27238

Union (9/16 in)

2

AH220366

Quick Coupler (9/16 in)

1

AA85322

Hydraulic Hose

1

AA85323

Hydraulic Hose

1

AA85328

Hydraulic Hose

1

AA87847

Hydraulic Hose

1

AA87848

Hydraulic Hose

1

AA87849

Hydraulic Hose

1

AA88657

Hydraulic Hose

1

AA88658

Hydraulic Hose

1

AA88984

Hydraulic Hose

1

AA88985

Hydraulic Hose

1

AA88987

Hydraulic Hose

1

AA89371

Hydraulic Hose

1

AA89372

Hydraulic Hose

1

AA89373

Hydraulic Hose

1

AA93517

Hydraulic Hose

1

Continued on next page

20-12

NL54298,00000F1 -19-31JAN20-1/29 020320

PN=54

Hoses and Fittings Install the Fittings 1. Install the adapters (A—D). Tighten to specification.

A94887 —UN—30JAN17

Specification Adapters (A)—Torque (lubricated)..................................................................................102 N·m (75 lb·ft) Adapters (B)—Torque (lubricated)....................................................................................69 N·m (51 lb·ft) Adapter (C)—Torque (lubricated)....................................................................................69 N·m (51 lb·ft) Adapter (D)—Torque (lubricated)..................................................................................102 N·m (75 lb·ft)

A—Adapter (61H1175) (2 used) B—Adapter (61H1174) (2 used)

C—Adapter (61H1162) D—Adapter (61H1163) NL54298,00000F1 -19-31JAN20-2/29

2. Install the adapters (A) and 90° elbow (B). Tighten to specification.

A—Adapter (61H1174) (2 used)

A94888 —UN—30JAN17

Specification Adapters (A)—Torque (lubricated)....................................................................................69 N·m (51 lb·ft) 90° Elbow (B)—Torque (lubricated)..................................................................................102 N·m (75 lb·ft) B—90° Elbow (61H1007)

Continued on next page

20-13

NL54298,00000F1 -19-31JAN20-3/29

020320

PN=55

A99201 —UN—31JAN18

A94895 —UN—30JAN17

Hoses and Fittings

Rear View of Right-Hand Bulkhead

Right-Hand Bulkhead Location A—Union (R27238) B—Nut (14H847)

C—Union (R47876) D—Nut (R27390)

E—45° Swivel Elbow (R37145)

NOTE: MY12—MY14 (S.N. 745101—760100) DB planters do not have the necessary hole to install the union as shown. To install the union, drill a 28.6 mm (1-1/4 in) hole on the wing bulkhead. Fabricate as necessary to avoid hose damage.

Specification 45° Swivel Elbow (E)—Torque (lubricated)..............................................................102 N·m (75 lb·ft)

3. Install the union (A), nut (B), union (C), nut (D), and 45° swivel elbow (E) on the right-hand bulkhead.

Tighten the 45° swivel elbow to specification.

A99200 —UN—31JAN18

A94897 —UN—31JAN17

NL54298,00000F1 -19-31JAN20-4/29

Rear View of Left-Hand Bulkhead

Left-Hand Bulkhead Location A—Union (R47876)

B—Nut (R27390)

C—45° Swivel Elbow (R37145)

NOTE: MY12—MY14 (S.N. 745101—760100) DB planters do not have the necessary hole to install the union as shown. To install the union, drill a 28.6 mm (1-1/4 in) hole on the wing bulkhead. Fabricate as necessary to avoid hose damage.

Specification 45° Swivel Elbow (C)—Torque (lubricated)..............................................................102 N·m (75 lb·ft)

4. Install the union (A), nut (B), and 45° swivel elbow (C) on the left-hand bulkhead. Tighten the 45° swivel elbow to specification.

Continued on next page

20-14

NL54298,00000F1 -19-31JAN20-5/29

020320

PN=56

A94898 —UN—31JAN17

A94691 —UN—19JAN17

Hoses and Fittings

Front Bulkhead Location A—Union (R47876) (2 used)

Front View of Front Bulkhead

B—Nut (R27390) (2 used)

C—Union (R27238) D—Nut (14H847)

NOTE: MY12—MY14 (S.N. 745101—760100) DB planters do not have the necessary holes to install the unions as shown. To install the unions, drill 28.6 mm (1-1/4 in) holes on the center bulkhead.

Fabricate as necessary to avoid hose damage.

5. Install the unions (A and C) and nuts (B and D).

A99207 —UN—01FEB18

A95114 —UN—06FEB17

NL54298,00000F1 -19-31JAN20-6/29

Front Right-Hand Side of Center Frame

Front Right-Hand View of Center Frame A—Swivel T-Fitting (AN33434)

6. Connect the swivel T-fitting (A). Tighten to specification.

Specification Swivel T-Fitting (A)—Torque (lubricated)................................................................50 N·m (37 lb·ft) Continued on next page

20-15

NL54298,00000F1 -19-31JAN20-7/29

020320

PN=57

A99208 —UN—31JAN18

A95115 —UN—06FEB17

Hoses and Fittings

Rear View of Priority Valve

Priority Valve Location A—90° Elbow (61H1052)

7. Install the 90° elbow (A). Tighten to specification.

Specification 90° Elbow (A)—Torque (lubricated)..................................................................................142 N·m (105 lb·ft) NL54298,00000F1 -19-31JAN20-8/29

Install the Hoses 1. Connect the hoses (A and B). Tighten to specification.

A—Return Hose (AA89371)

A94889 —UN—30JAN17

Specification Hoses (A and B)—Torque (lubricated)..................................................................................102 N·m (75 lb·ft) B—Pressure Hose (AA88984)

NL54298,00000F1 -19-31JAN20-9/29

2. Route the hoses (A and B) along the right-hand wing.

B—Pressure Hose (AA88984)

A94890 —UN—30JAN17

A—Return Hose (AA89371)

Front View of Center Frame Continued on next page

20-16

NL54298,00000F1 -19-31JAN20-10/29

020320

PN=58

Priority Valve Location

A99209 —UN—31JAN18

A99208 —UN—31JAN18

Hoses and Fittings

Front View of Right-Hand Wing

3. Continue routing hose (A) along the right-hand wing.

4. Route and connect hose (B). Tighten to specification.

A—Return Hose (AA89371)

A94892 —UN—30JAN17

Specification Hose (B)—Torque (lubricated)..................................................................................102 N·m (75 lb·ft) B—Pressure Hose (AA88984)

Front View of Right-Hand Wing

A99211 —UN—31JAN18

A99210 —UN—31JAN18

NL54298,00000F1 -19-31JAN20-11/29

Front View of Right-Hand Wing

A—Return Hose (AA89371)

5. Continue routing the hose (A) along the right-hand wing.

Continued on next page

20-17

NL54298,00000F1 -19-31JAN20-12/29

020320

PN=59

Hoses and Fittings

6. Connect the hose (A). Tighten to specification.

Specification Hose (A)—Torque (lubricated)..................................................................................102 N·m (75 lb·ft) A99212 —UN—31JAN18

NOTE: Route the hose (B) through the hitch tube BEFORE connecting it to the union.

7. Connect the hose (B). Tighten to specification.

Specification Hose (B)—Torque (lubricated)..................................................................................102 N·m (75 lb·ft)

Right-Hand Bulkhead A—Return Hose (AA89371)

B—Return Hose (AA87848) NL54298,00000F1 -19-31JAN20-13/29

8. Connect the hose (A). Tighten to specification.

A94899 —UN—31JAN17

Specification Hose (A)—Torque (lubricated)..................................................................................102 N·m (75 lb·ft) A—Return Hose (AA87848)

Front View of Front Bulkhead NL54298,00000F1 -19-31JAN20-14/29

9. Connect the hose (A). Tighten to specification.

A94900 —UN—31JAN17

Specification Hose (A)—Torque (lubricated)..................................................................................102 N·m (75 lb·ft) A—Return Hose (AA85323)

Front View of Front Bulkhead Continued on next page

20-18

NL54298,00000F1 -19-31JAN20-15/29

020320

PN=60

Priority Valve Location

A99213 —UN—31JAN18

A99208 —UN—31JAN18

Hoses and Fittings

Rear View of Priority Valve

10. Connect the hose (A) to the priority valve. Tighten to specification.

A94902 —UN—31JAN17

Specification Hose (A)—Torque (lubricated)....................................................................................42 N·m (31 lb·ft)

11. Route and connect to the other end of the hose (A).

Tighten to specification.

Specification Hose (A)—Torque (lubricated)....................................................................................42 N·m (31 lb·ft)

Front View of Priority Valve

A—Load Sense Hose (AA88987) NL54298,00000F1 -19-31JAN20-16/29

12. Connect the hose (A). Tighten to specification.

A94903 —UN—31JAN17

Specification Hose (A)—Torque (lubricated)....................................................................................42 N·m (31 lb·ft) A—Load Sense Hose (AA89373)

Front View of Priority Valve Continued on next page

20-19

NL54298,00000F1 -19-31JAN20-17/29

020320

PN=61

A99215 —UN—31JAN18

A99214 —UN—31JAN18

Hoses and Fittings

Front View of Right-Hand Wing

Front View of Right-Hand Wing

A—Load Sense Hose (AA89373)

13. Route the hose (A) along the right-hand wing.

NL54298,00000F1 -19-31JAN20-18/29

14. Connect the hose (A). Tighten to specification.

Specification Hose (A)—Torque (lubricated)....................................................................................42 N·m (31 lb·ft) A99216 —UN—31JAN18

NOTE: Route the hose (B) through the hitch tube BEFORE connecting it to the union.

15. Connect the hose (B). Tighten to specification.

Specification Hose (B)—Torque (lubricated)....................................................................................42 N·m (31 lb·ft)

Front View of Right-Hand Bulkhead A—Load Sense Hose (AA89373)

B—Load Sense Hose (AA87849) NL54298,00000F1 -19-31JAN20-19/29

16. Connect the hose (A). Tighten to specification.

A94907 —UN—31JAN17

Specification Hose (A)—Torque (lubricated)....................................................................................42 N·m (31 lb·ft) A—Load Sense Hose (AA87849)

Front View of Front Bulkhead Continued on next page

20-20

NL54298,00000F1 -19-31JAN20-20/29

020320

PN=62

Hoses and Fittings

17. Connect the hose (A). Tighten to specification.

A94908 —UN—31JAN17

Specification Hose (A)—Torque (lubricated)....................................................................................42 N·m (31 lb·ft) A—Load Sense Hose (AA93517)

Front View of Front Bulkhead

A99208 —UN—31JAN18

A94910 —UN—01FEB17

NL54298,00000F1 -19-31JAN20-21/29

Left-Hand View of Priority Valve

Priority Valve Location A—Pressure Hose (AA88985)

B—Pressure Hose (AA89372)

18. Connect both ends of the hose (A). Tighten to specification.

19. Connect the hose (B). Tighten to specification.

Specification Hose (B)—Torque (lubricated)..................................................................................102 N·m (75 lb·ft)

Specification Hose (A)—Torque (lubricated)..................................................................................102 N·m (75 lb·ft)

Continued on next page

20-21

NL54298,00000F1 -19-31JAN20-22/29

020320

PN=63

A99218 —UN—31JAN18

A99217 —UN—31JAN18

Hoses and Fittings

Rear View of Left-Hand Wing

Front View of Left-Hand Wing

20. Route the hose (A) along the left-hand wing.

21. Connect the hose (A). Tighten to specification.

A99219 —UN—31JAN18

Specification Hose (A)—Torque (lubricated)..................................................................................102 N·m (75 lb·ft)

NOTE: Route the hose (B) through the hitch tube BEFORE connecting it to the union.

22. Connect the hose (B). Tighten to specification.

Specification Hose (B)—Torque (lubricated)..................................................................................102 N·m (75 lb·ft)

Front View of Left-Hand Bulkhead A—Hydraulic Hose (AA89372)

B—Hydraulic Hose (AA87847) NL54298,00000F1 -19-31JAN20-23/29

23. Connect the hose (A). Tighten to specification.

A95009 —UN—31JAN17

Specification Hose (A)—Torque (lubricated)..................................................................................102 N·m (75 lb·ft) A—Hydraulic Hose (AA87847)

Front View of Left-Hand Hitch Tube Continued on next page

20-22

NL54298,00000F1 -19-31JAN20-24/29

020320

PN=64

Hoses and Fittings

24. Connect the hose (A). Tighten to specification.

A95027 —UN—01FEB17

Specification Hose (A)—Torque (lubricated)..................................................................................102 N·m (75 lb·ft) A—Hydraulic Hose (AA85322)

Front View of Left-Hand Hitch Tube

A99220 —UN—31JAN18

A95011 —UN—31JAN17

NL54298,00000F1 -19-31JAN20-25/29

A99208 —UN—31JAN18

A95013 —UN—31JAN17

Rear View of Center Frame

Rear View of Priority Valve

Priority Valve Location A—Hydraulic Hose (AA93517)

25. Connect the hose (A). Tighten to specification.

27. Connect the hose (A). Tighten to specification.

Specification

Specification Hose (A)—Torque (lubricated)..................................................................................102 N·m (75 lb·ft)

Hose (A)—Torque (lubricated)..................................................................................102 N·m (75 lb·ft)

26. Route the hose (A) along the center frame.

Continued on next page

20-23

NL54298,00000F1 -19-31JAN20-26/29

020320

PN=65

Hoses and Fittings

28. Connect the hose (A). Tighten to specification.

A95014 —UN—31JAN17

Specification Hose (A)—Torque (lubricated)....................................................................................50 N·m (37 lb·ft) A—Hydraulic Hose (AA85328)

Front View of Priority Valve

Front View of Center Frame

A99222 —UN—31JAN18

A99221 —UN—31JAN18

NL54298,00000F1 -19-31JAN20-27/29

Front View of Center Frame

A—Hydraulic Hose (AA85328)

29. Route and connect the hose (A). Tighten to specification.

Specification Hose (A)—Torque (lubricated)....................................................................................50 N·m (37 lb·ft) NL54298,00000F1 -19-31JAN20-28/29

30. Connect the hoses (A and B). Tighten to specification.

A—Pressure Hose (AA88657)

A94694 —UN—19JAN17

Specification Hoses (A and B)—Torque (lubricated)....................................................................................50 N·m (37 lb·ft) B—Return Hose (AA88658)

Left-Hand View of Center Frame NL54298,00000F1 -19-31JAN20-29/29

20-24

020320

PN=66

Hoses and Fittings

BA33395 — Install the Row Unit Hoses NOTE: Use the fitting kit BA33638.

Parts List Part Number

Description

Quantity

14M7276

Nut, M16

8

38H5092

Nut (13/16 in)

10

61H1505

T-Fitting (with three 13/16-in ports)

6

A107209

Bracket

4

H77698

Tie Band, 381 mm (15 in)

70

A100469

U-Bolt, M16 x 170

4

KK21790

Cross Fitting (with four 13/16-in ports)

4

A99223 —UN—05FEB18

A99164 —UN—02FEB18

Install the Hardware

Rear View of Left-Hand Wing

A99310 —UN—08FEB18

A99167 —UN—06AUG18

Inner Bracket Locations

Rear View of Right-Hand Wing A—Bracket (A107209) (2 used) B—U-Bolt, M16 x 170 (2 used)

Rear View

C—Nut, M16 (4 used) E—Distance, 7400 mm (24 ft 3 in) D—Distance, 7600 mm (24 ft 11 in)

NOTE: Install the brackets at the recommended distances (D and E).

1. Install the brackets (A) using U-bolts (B) and nuts (C).

Continued on next page

20-25

NL54298,00000F2 -19-13JAN20-1/18

020320

PN=67

A99311 —UN—08FEB18

A99312 —UN—08FEB18

Hoses and Fittings

Rear View of Left-Hand Wing A—Cross Fitting (KK21790) (4 used)

Rear View of Right-Hand Wing

B—Nut (38H5092) (4 used)

2. Install the cross fittings (A) and the nuts (B) on the brackets.

A99313 —UN—08FEB18

A99229 —UN—05FEB18

NL54298,00000F2 -19-13JAN20-2/18

A99315 —UN—08FEB18

Rear View of Left-Hand Wing

A99314 —UN—08FEB18

Outer Bracket Locations

Rear View of Right-Hand Wing A—Bracket (A107209) (2 used) B—U-Bolt, M16 x 170 (2 used)

Rear View

C—Nut, M16 (4 used) D—Distance, 2200 mm (7 ft 3 in)

E—Distance, 2300 mm (7 ft 7 in)

NOTE: Install the brackets at the recommended distances (D and E).

3. Install the brackets (A) using U-bolts (B) and nuts (C).

Continued on next page

20-26

NL54298,00000F2 -19-13JAN20-3/18

020320

PN=68

Outer Bracket Locations

A99316 —UN—08FEB18

A99229 —UN—05FEB18

Hoses and Fittings

Rear View of Left-Hand Wing

4. Install the cross fittings (A) and nuts (B) on the brackets.

B—Nut (38H5092) (4 used)

A99317 —UN—08FEB18

A—Cross Fitting (KK21790) (4 used)

Rear View of Right-Hand Wing

Fitting Location A—T-Fitting (61H1505) (2 used)

A99233 —UN—05FEB18

A99232 —UN—05FEB18

NL54298,00000F2 -19-13JAN20-4/18

Rear Left-Hand View of Center Frame

B—Nut (38H5092) (2 used)

5. Install the T-fittings (A) and nuts (B) on the bulkhead.

Continued on next page

20-27

NL54298,00000F2 -19-13JAN20-5/18

020320

PN=69

Hoses and Fittings Install the Hoses Parts List Part Number

Description

Quantity

AA89578

Hydraulic Hose

20

AA89579

Hydraulic Hose

20

AA89893

Hydraulic Hose

10

AA89899

Hydraulic Hose

10

AA89996

Hydraulic Hose

2

AA89997

Hydraulic Hose

2

AA90040

Hydraulic Hose

1

AA90044

Hydraulic Hose

1

AA90392

Hydraulic Hose

1

AA90393

Hydraulic Hose

1

AA90395

Hydraulic Hose

1

AA90396

Hydraulic Hose

1

AA90425

Hydraulic Hose

1

AA90430

Hydraulic Hose

1

AA90519

Hydraulic Hose

1

AA90520

Hydraulic Hose

1

AA92027

Hydraulic Hose

2

AA92028

Hydraulic Hose

2

AA92093

Hydraulic Hose

1

AA92094

Hydraulic Hose

1

AA92020

Hydraulic Hose

2

AA92021

Hydraulic Hose

2

AA94367

Hydraulic Hose

8

AA94368

Hydraulic Hose

8

AA94369

Hydraulic Hose

1

AA94370

Hydraulic Hose

1

AA94394

Hydraulic Hose

1

AA94395

Hydraulic Hose

1

1. Connect the previously installed hoses (A and B) to the T-fittings.

B—Pressure Hose (AA88657)

A99234 —UN—05FEB18

A—Return Hose (AA88658)

Left-Hand Side of Center Frame Continued on next page

20-28

NL54298,00000F2 -19-13JAN20-6/18

020320

PN=70

A99235 —UN—05FEB18

A95124 —UN—07FEB17

Hoses and Fittings

Right-Hand Side of Combination Valve Block

Left-Hand Side of Combination Valve Block A—Pressure Hose (AA89426)

B—Return Hose (AA89427) C—Pressure Hose (AA89432)

D—Return Hose (AA89433)

2. Connect the hoses (A—D). Tighten to specification.

Specification Hoses (A—D)—Torque (lubricated)....................................................................................50 N·m (37 lb·ft)

A99236 —UN—05FEB18

A99195 —UN—09FEB18

NL54298,00000F2 -19-13JAN20-7/18

Front View of Left-Hand Wing

Top Front View of Center Frame

3. Route the hoses (A—D) along the left-hand and right-hand wings.

C—Pressure Hose (AA89432) D—Return Hose (AA89433) A99196 —UN—09FEB18

A—Pressure Hose (AA89426) B—Return Hose (AA89427)

Front View of Right-Hand Wing Continued on next page

20-29

NL54298,00000F2 -19-13JAN20-8/18

020320

PN=71

Front View of Left-Hand Inner Bracket A—Pressure Hose (AA89426)

A99198 —UN—09FEB18

A99197 —UN—09FEB18

Hoses and Fittings

Front View of Right-Hand Inner Bracket

B—Return Hose (AA89427) C—Pressure Hose (AA89432)

D—Return Hose (AA89433)

4. Connect the hoses (A—D) to the previously installed T-fittings. Tighten to specification.

Specification Hoses (A—D)—Torque (lubricated)....................................................................................50 N·m (37 lb·ft)

Front View of Left-Hand Inner Bracket A—Pressure Hose (AA89422)

A99464 —UN—09FEB18

A99199 —UN—09FEB18

NL54298,00000F2 -19-13JAN20-9/18

Front View of Right-Hand Inner Bracket

B—Return Hose (AA89423) C—Pressure Hose (AA86590)

D—Return Hose (AA86591)

5. Install the hoses (A—D). Tighten to specification.

Specification Hoses (A—D)—Torque (lubricated)....................................................................................50 N·m (37 lb·ft) Continued on next page

20-30

NL54298,00000F2 -19-13JAN20-10/18

020320

PN=72

A99466 —UN—09FEB18

A99465 —UN—09FEB18

Hoses and Fittings

Front View of Left-Hand Wing A—Pressure Hose (AA89422)

Front View of Right-Hand Wing

B—Return Hose (AA89423) C—Pressure Hose (AA86590)

D—Return Hose (AA86591)

6. Route the hydraulic hoses (A—D) along the left-hand and right-hand wings.

Front View of Left-Hand Outer Bracket A—Pressure Hose (AA89422)

A99468 —UN—09FEB18

A99467 —UN—09FEB18

NL54298,00000F2 -19-13JAN20-11/18

Front View of Right-Hand Outer Bracket

B—Return Hose (AA89423) C—Pressure Hose (AA86590)

D—Return Hose (AA86591)

7. Install the hoses (A—D). Tighten to specification.

Specification Hoses (A—D)—Torque (lubricated)....................................................................................50 N·m (37 lb·ft) Continued on next page

20-31

NL54298,00000F2 -19-13JAN20-12/18

020320

PN=73

A99241 —UN—05FEB18

Hoses and Fittings

Row Units 1—6

NOTE: Pressure ports (E) are on the left-hand side.

Return ports (F) are on the right-hand side.

Pressure hoses always connect to pressure ports, and return hoses always connect to return ports.

A106198 —UN—25NOV19

Use the provided tables to determine row unit-specific hoses.

Right-hand and left-hand sides are determined by facing in the direction of forward travel.

8. Install the hoses on row units (1—6). Tighten to specification.

Top of Hydraulic Downforce Actuator

Specification Row Unit Hoses—Torque (lubricated)....................................................................................24 N·m (18 lb·ft)

A—Pressure Hose (AA94368) B—Return Hose (AA94367) C—Return Hose (AA94367)

D—Pressure Hose (AA94368) E—Pressure Port F— Return Port

Row Unit Hoses Location

Pressure Hose

Return Hose

Row 1 to Row 2

AA88935

AA88936

Row 2 to Row 3

AA89899

AA89893

Row 3 to T-Fitting

AA94368

AA94367

T-Fitting to Row 4

AA94368

AA94367

Row 4 to Row 5

AA88935

AA88936

Row 5 to Row 6

AA88935

AA88936

Continued on next page

20-32

NL54298,00000F2 -19-13JAN20-13/18

020320

PN=74

A99323 —UN—14FEB18

Hoses and Fittings

Row Units 7—13

NOTE: Pressure ports (E) are on the left-hand side.

Return ports (F) are on the right-hand side.

Pressure hoses always connect to pressure ports, and return hoses always connect to return ports.

A106198 —UN—25NOV19

9. Install the hoses on row units (7—13). Tighten to specification.

Specification Row Unit Hoses—Torque (lubricated)....................................................................................24 N·m (18 lb·ft) Top of Hydraulic Downforce Actuator A—Pressure Hose (AA94368) B—Return Hose (AA94367) C—Return Hose (AA94367)

D—Pressure Hose (AA94368) E—Pressure Port F— Return Port

Row Unit Hoses Location

Pressure Hose

Return Hose

Row 7 to Row 8

AA88935

AA88936

Row 8 to Row 9

AA88935

AA88936

Row 9 to Row 10

AA88935

AA88936

Row 10 to T-Fitting

AA94368

AA94367

T-Fitting to Row 11

AA94368

AA94367

Row 11 to Row 12

AA89428

AA89429

Row 12 to Row 13

AA89716

AA89717

Continued on next page

20-33

NL54298,00000F2 -19-13JAN20-14/18

020320

PN=75

A99320 —UN—08FEB18

Hoses and Fittings

Row Units 14—23

NOTE: Pressure ports (E) are on the left-hand side.

Return ports (F) are on the right-hand side.

Pressure hoses always connect to pressure ports, and return hoses always connect to return ports.

A106198 —UN—25NOV19

10. Install the hoses on row units (14—23). Tighten to specification.

Specification Row Unit Hoses—Torque (lubricated)....................................................................................24 N·m (18 lb·ft) Top of Hydraulic Downforce Actuator A—Pressure Hose (AA94370) B—Return Hose (AA94369) C—Return Hose (AA94369)

D—Pressure Hose (AA94370) E—Pressure Port F— Return Port

Row Unit Hoses Location

Pressure Hose

Return Hose

Row 14 to Row 15

AA89899

AA89893

Row 15 to Row 16

AA89899

AA89893

Row 16 to Row 17

AA92028

AA92027

Row 17 to Row 18

AA89899

AA89893

Row 18 to T-Fitting

AA94370

AA94369

T-Fitting to Row 19

AA94370

AA94369

Row 19 to Row 20

AA89899

AA89893

Row 20 to Row 21

AA92028

AA92027

Row 21 to Row 22

AA89899

AA89893

Row 22 to Row 23

AA89899

AA89893

Continued on next page

20-34

NL54298,00000F2 -19-13JAN20-15/18

020320

PN=76

A99324 —UN—14FEB18

Hoses and Fittings

Row Units 24—30

NOTE: Pressure ports (E) are on the left-hand side.

Return ports (F) are on the right-hand side.

Pressure hoses always connect to pressure ports, and return hoses always connect to return ports.

A106198 —UN—25NOV19

11. Install the hoses on row units (24—30). Tighten to specification.

Specification Row Unit Hoses—Torque (lubricated)....................................................................................24 N·m (18 lb·ft) Top of Hydraulic Downforce Actuator A—Pressure Hose (AA94368) B—Return Hose (AA94367) C—Return Hose (AA94367)

D—Pressure Hose (AA94368) E—Pressure Port F— Return Port

Row Unit Hoses Location

Pressure Hose

Return Hose

Row 24 to Row 25

AA89716

AA89717

Row 25 to Row 26

AA89899

AA89893

Row 26 to Row 27

AA88935

AA88936

Row 27 to T-Fitting

AA94368

AA94367

T-Fitting to Row 28

AA94368

AA94367

Row 28 to Row 29

AA88935

AA88936

Row 29 to Row 30

AA88935

AA88936

Continued on next page

20-35

NL54298,00000F2 -19-13JAN20-16/18

020320

PN=77

A99245 —UN—05FEB18

Hoses and Fittings

Row Units 31—36

NOTE: Pressure ports (E) are on the left-hand side.

Return ports (F) are on the right-hand side.

Pressure hoses always connect to pressure ports, and return hoses always connect to return ports.

A106198 —UN—25NOV19

12. Install the hoses on row units (31—36). Tighten to specification.

Specification Row Unit Hoses—Torque (lubricated)....................................................................................24 N·m (18 lb·ft) Top of Hydraulic Downforce Actuator A—Pressure Hose (AA94368) B—Return Hose (AA94367) C—Return Hose (AA94367)

D—Pressure Hose (AA94368) E—Pressure Port F— Return Port

Row Unit Hoses Location

Pressure Hose

Return Hose

Row 31 to Row 32

AA88935

AA88936

Row 32 to Row 33

AA88935

AA88936

Row 33 to T-Fitting

AA94368

AA94367

T-Fitting to Row 34

AA94368

AA94367

Row 34 to Row 35

AA89899

AA89893

Row 35 to Row 36

AA88935

AA88936

Continued on next page

20-36

NL54298,00000F2 -19-13JAN20-17/18

020320

PN=78

A94497 —UN—18JAN17

A106199 —UN—25NOV19

Hoses and Fittings

Combination Valve Block Location

Combination Valve Block Shown

A—Pressure Sensor

13. Locate the pressure sensor harness connector on the center frame harness. Connect the pressure sensor

harness to the previously installed pressure sensor (A) on the combination valve block.

NL54298,00000F2 -19-13JAN20-18/18

20-37

020320

PN=79

System Startup IRHD Configuration Setup A59325 —UN—19FEB07

1. Select Menu.

Menu WP29706,0000B03 -19-30JAN18-1/5

A94029 —UN—11OCT17

2. Select Message Center.

Message Center WP29706,0000B03 -19-30JAN18-2/5

A94030 —UN—11OCT17

3. Select Addresses.

Addresses Continued on next page

25-1

WP29706,0000B03 -19-30JAN18-3/5

020320

PN=80

System Startup

A94031 —UN—01DEC16

Enter

A93817 —UN—30NOV16

A

T

T D

C

B

A—Address Button B—T-Icon

A93819 —UN—30NOV16

A93818 —UN—30NOV16

E

D—100 Input E—Number

C—MMC.001 Implement

4. After the Device drop-down list appears, select and hold the Addresses softkey (A) for ten seconds.T-icon (B) appears indicating technician mode is active.

NOTE: The 100 Input page opens with a diagnostic value (E) displayed in the center of the screen.

5. Scroll to MMC.001 Implement (C) and select it.

7. Select the Enter button.

8. Enter 1 on the keypad and select Enter/Accept .

6. Scroll to 100 Input (D) and select it.

Continued on next page

25-2

WP29706,0000B03 -19-30JAN18-4/5

020320

PN=81

System Startup

A94031 —UN—01DEC16

T

Enter

A93820 —UN—30NOV16

A

A—Diagnostic Value

9. The diagnostic value (A) updates to a 1 . Save the changes by selecting the Enter button.

11. Proceed to Gauge Wheel Downforce Setup.

10. Close the technician mode. Hold the Addresses softkey for ten seconds and verify that the T-icon disappears.

WP29706,0000B03 -19-30JAN18-5/5

A—Menu

A94481 —UN—21DEC16

A94480 —UN—21DEC16

Parallel Arm Setup

B—Message Center

IMPORTANT: Complete the IRHD Configuration Setup BEFORE setting up the parallel arms.

1. Write down the length of the parallel arms (regular or long) for each row.

2. Select Menu (A).

Avoid machine damage. The standby pressure varies. Input the correct parallel arm length for each row.

3. Select Message Center (B).

Continued on next page

25-3

LM78752,00003D3 -19-27FEB18-1/12

020320

PN=82

System Startup

4. Select Addresses (A).

A—Addresses

A93816 —UN—30NOV16

A

LM78752,00003D3 -19-27FEB18-2/12

A94140 —UN—21DEC16

A93817 —UN—30NOV16

A

5. The Device drop-down list appears. Select and hold Addresses (A) for up to 10 seconds until a T-icon (B) appears.

6. Scroll through the drop-down list until MMC.001 Implement (C) appears and select it.

7. The MMC.001 Inputs list appears. Use the arrows to find the diagnostic address 137 Input (D) and select it.

A94472 —UN—03JAN17

NOTE: The 137 Input page shows the Pneumatic System Configuration. Note the number (E) displayed in the center of the screen.

8. Select Enter (F).

A—Addresses B—T-Icon C—MMC.001 Implement

D—137 Input E—Number F— Enter Continued on next page

25-4

LM78752,00003D3 -19-27FEB18-3/12

020320

PN=83

System Startup

9. Enter the value that applies to the current pneumatic configuration using the number pad.

• 0 = No air system is installed.

• 1 = The air system is used to control the row cleaners or closing wheels.

• 2 = The air system is only used to control the tank pressure for non-Deere pneumatic components.

10. Select Accept (A) on the number pad.

A94473 —UN—21DEC16

A—Accept

Number Pad LM78752,00003D3 -19-27FEB18-4/12

11. Verify that the correct configuration value (A) appears on the 137 input page.

12. Save the change by selecting Enter (B).

B—Enter

A94482 —UN—03JAN17

A—Configuration Value

Continued on next page

25-5

LM78752,00003D3 -19-27FEB18-5/12

020320

PN=84

A—050 Input

B—Number

A94475 —UN—03JAN17

A94474 —UN—21DEC16

System Startup

C—Enter

13. Use the arrows to find the diagnostic address 050 Input (A) and select it.

14. Select Enter (C).

NOTE: The 050 Input page is the row number index. It opens with a number (B) displayed in the center of the screen.

LM78752,00003D3 -19-27FEB18-6/12

15. Verify the parallel arm configuration on a single row by entering the row number.

16. Select Accept (A).

A94473 —UN—21DEC16

A—Accept

Number Pad Continued on next page

25-6

LM78752,00003D3 -19-27FEB18-7/12

020320

PN=85

System Startup

17. The selected row number (A) appears.

18. Save the choice by selecting Enter (B).

B—Enter

A94479 —UN—03JAN17

A—Row Number

A—159 Input

B—Number

A94483 —UN—03JAN17

A94476 —UN—03JAN17

LM78752,00003D3 -19-27FEB18-8/12

C—Enter

19. Use the arrows to find the diagnostic address 159 Input (A) and select it.

20. Select Enter (C).

NOTE: The 159 Input page is for parallel arm configuration. It opens with a number (B) displayed in the center of the screen.

Continued on next page

25-7

LM78752,00003D3 -19-27FEB18-9/12

020320

PN=86

System Startup

21. Enter a 0 for regular parallel arms or a 1 for long parallel arms using the number pad.

22. Select Accept (A).

A94473 —UN—21DEC16

A—Accept

Number Pad LM78752,00003D3 -19-27FEB18-10/12

23. Verify that the 159 input page has the correct parallel arm configuration (A).

24. Save the change by selecting Enter (B).

B—Enter

A94484 —UN—03JAN17

A—Parallel Arm Configuration

Continued on next page

25-8

LM78752,00003D3 -19-27FEB18-11/12

020320

PN=87

A94477 —UN—21DEC16

A94478 —UN—21DEC16

System Startup

A—172 Input

25. Use the arrows to find the diagnostic address 172 Input (A) and select it.

26. Confirm that the value in 172 Input is correct for the 159 Input verified:

• If address 159 Input is 0, then address 172 Input

a. Select address 172 Input. b. Select Enter. c. Enter the correct number for regular or long parallel arms.

must be 5044 (regular parallel arms).

d. Select Accept.

must be 6206 (long parallel arms).

e. Select Enter.

• If address 159 Input is 1, then address 172 Input 27. If address 172 Input is incorrect, reverify address 159 Input.

28. If all settings are correct, repeat the steps for address 159 Input and 172 Input for every row number.

If address 159 Input is verified and address 172 Input is incorrect, manually change address 172 Input.

LM78752,00003D3 -19-27FEB18-12/12

25-9

020320

PN=88

System Startup

A79863 —UN—29JAN14

A59325 —UN—19FEB07

Gauge Wheel Downforce Setup

Menu

Planter Setup Button

A59377 —UN—23FEB07

A

A93813 —UN—30NOV16

A59172 —UN—29JAN07

Planter Button

A93814 —UN—30NOV16

Settings Button

A—Zero Sensor

1. Select the Menu button>> then the Planter button>> then the Planter Setup button>> then the Frame tab.

5. Verify that the frame tab page now shows that all active row sensors are enabled.

2. The display now shows that All Rows are enabled.

NOTE: To zero the downforce sensors, the planter must be raised and stopped.

3. If the display does not show that all rows are enabled, select the Settings button.

4. Select All Rows enabled from the options and save your changes by selecting the Enter button.

6. Select the Zero Sensor button (A).

WP29706,0000B02 -19-06APR17-1/1

25-10

020320

PN=89

System Startup

Individual Row Hydraulic Downforce (IRHD) Initial Flush and Test

X9811 —UN—23AUG88

To warm the hydraulic fluid and remove particulates from the hoses, use the bypass hose (B). To remove air from the system, flush particulates from the valves, and test the accumulators, use on-screen procedures.

CAUTION: Avoid serious injury from fluid injection. Do not connect or disconnect hoses with the tractor engine running. (See Avoid High-Pressure Fluids.)

Fluid Injection Hazard

1. Turn off the tractor.

2. There are couplers (A) on one end of each IRHD section. Locate a set of couplers, remove the coupler caps, and attach the bypass hose (B).

A89119 —UN—23DEC15

3. Keep bystanders clear and start the tractor.

NOTE: See the tractor Operator’s Manual for oil temperature specifics.

4. Continue the hydraulic flow until the oil is approximately 50°C (120°F) (hoses are warm when touched).

5. Turn off the tractor.

6. Remove the bypass hose and replace the coupler caps.

Bypass Hose and Row Unit with IRHD Couplers

NOTE: An unused selective control valve (SCV) is needed for the valve and accumulator procedures.

A100619 —UN—23MAY18

7. If all SCVs are in use, remove the hoses from one.

(See the Recommendations for Hydraulic Connections for additional information.)

8. Start the tractor.

NOTE: Set a low idle and deactivate all SCVs for low hydraulic pressure during the air purge test.

9. Perform the Air Purge Test procedure twice using the SeedStar™ application software (see the Planter Diagnostics Procedures).

10. To cycle the actuator cylinders and help discharge air, raise and lower the planter frame four times.

NOTE: Set a low idle and deactivate all SCVs for low hydraulic pressure during the air purge test.

11. Perform the Air Purge Test procedure. Verify that all rows on the display show green bars and that the procedure is successful.

NOTE: Set a high idle and set an unused SCV to continuous detent for high hydraulic pressure during the valve tests.

Steel Tube with IRHD Couplers A—Couplers

B—Bypass Hose

12. Force the power beyond into high-pressure mode.

Place an unused SCV into a continuous detent.

13. Perform the Valve Flush Test procedure. Verify that all rows on the display show green bars and that the procedure is successful.

14. Perform the Valve Test procedure. Verify that all rows on the display show green bars and that the procedure is successful.

15. Perform the Accumulator Test procedure. Verify that all rows on the display show green bars and that the procedure is successful.

SeedStar is a trademark of Deere & Company OUO6074,0001122 -19-22NOV19-1/1

25-11

020320

PN=90

System Startup

A79863 —UN—29JAN14

A59567 —UN—08MAR07

Valve Test (IRHD System Only)

Diagnostic Button

A—Tests Tab B—Drop-Down Box

A91231 —UN—29JUN16

A91232 —UN—29JUN16

Planter Button

E—End Row Input Box F— Start / Stop Button

C—Valve Test D—Start Row Input Box

Reasons for running this test:

• Performance bars are showing red instead of black • Valves are not meeting performance requirements IMPORTANT: Before running the valve test, Individual Row Hydraulic Downforce (IRHD) circuit must be connected to the tractor power beyond.

At least one SCV must be in continuous detent position in order to provide high pump pressure during the test.

1. Use the following test for checking the functionality of the actuator control valve.

2. Select IRHD Tests from the drop-down box (B).

3. Select Valve Test (C) from the drop-down list.

4. Input selected row units for the valve test using input boxes (D and E).

5. To start the valve test, select the start/stop button (F).

NOTE: To stop valve test at any time, select button (F).

Test Complete appears on-screen when valve test is completed without failures.

If the valve test fails, perform valve flush test. (See Valve Flush Test in this section.)

Select Menu >> Planter button >> Diagnostics button >> Tests tab (A).

BB83525,00002F8 -19-06APR17-1/1

25-12

020320

PN=91

System Startup

A79863 —UN—29JAN14

A59567 —UN—08MAR07

Valve Flush Test (IRHD System Only)

Diagnostic Button

A—Tests Tab B—Drop-Down Box

A91237 —UN—29JUN16

A91235 —UN—29JUN16

Planter Button

E—End Row Input Box F— Start / Stop Button

C—Valve Flush D—Start Row Input Box

Reasons for running this test:

• Anytime work has been done on the hydraulic circuit • If valve is sticking • Display performance bars are red or maximum pressure is not being achieved

IMPORTANT: Before running the valve flush test, Individual Row Hydraulic Downforce (IRHD) circuit must be connected to the tractor power beyond. At least one SCV must be in continuous detent position in order to provide high pump pressure during the test.

4. Input selected row units for the valve flush test using the input boxes (D and E).

5. To start the valve flush test, select the start/stop button (F).

NOTE: To stop valve flush test at any time, select button (F).

Test Complete appears on-screen when valve flush test is completed without failures.

If test fails, repeat the test up to three times.

1. Use the following test to remove hydraulic contamination from the valve and actuator assembly.

If test failure or performance is still an issue, have a John Deere™ dealer remove and clean the valve cartridge with approved hydraulic parts cleaner.

Select Menu >> Planter button >> Diagnostics button >> Tests tab (A).

If performance and test results do not improve after parts cleaning, have John Deere™ dealer replace valve cartridge assembly.

2. Select IRHD Tests from the drop-down box (B).

3. Select Valve Flush (C) from the drop-down list.

Continued on next page

25-13

BB83525,00002F7 -19-06APR17-1/2 020320

PN=92

System Startup John Deere is a trademark of Deere & Company BB83525,00002F7 -19-06APR17-2/2

25-14

020320

PN=93

System Startup

A79863 —UN—29JAN14

A59567 —UN—08MAR07

Air Purge Test (IRHD System Only)

Diagnostic Button

A—Tests Tab B—Drop-Down Box

A91233 —UN—29JUN16

A91234 —UN—29JUN16

Planter Button

E—End Row Input Box F— Start / Stop Button

C—Air Purge D—Start Row Input Box

Reason for running this test: Anytime air has been allowed into the hydraulic circuit when switching tractors or changing hydraulic hoses.

IMPORTANT: Before running the air purge test, Individual Row Hydraulic Downforce (IRHD) circuit must be connected to the tractor power beyond. The test must be performed at idle with all the other SCVs disengaged.

This test must be run at least two times.

1. Use the following test to remove air from the hydraulic circuits.

Select Menu >> Planter button >> Diagnostics button >> Tests tab (A).

3. Select Air Purge (C) from the drop-down list.

4. Input selected row units for the air purge test using the input boxes (D and E).

5. To start air purge test, select the start/stop button (F).

NOTE: To stop valve test at any time, select button (F).

6. Repeat this test 1 time.

Test Complete appears on-screen when air purge test is completed without failures.

The length of timer for the air purge procedure varies by the number of rows being flushed.

7. Check and fill the hydraulic reservoir in the tractor.

2. Select IRHD Tests from the drop-down box (B).

BB83525,00002F6 -19-06APR17-1/1

25-15

020320

PN=94

System Startup

A79863 —UN—29JAN14

A59567 —UN—08MAR07

Accumulator Test (IRHD System Only)

Diagnostic Button

Planter Button

A B

E

F

A—Tests Tab B—Drop-Down Box

A91883 —UN—19AUG16

A91882 —UN—19AUG16

D

E—End Row Input Box F— Start/Stop Button

C—Accumulator Test D—Start Row Input Box

Reason for running this test:

2. Select IRHD Tests from the drop-down box (B).

• Displayed downforce showing erratic peak highs • Ride quality is degrading • Suspected accumulator leaks

3. Select Accumulator Test (C) from the drop-down list.

IMPORTANT: Before running the accumulator test, IRHD circuit must be connected to tractor power beyond. Test must be performed with at least one SCV in continuous detent position in order to provide high pump pressure.

5. To start or stop the test, select the Start/Stop button (F).

1. Use the following test for verifying the accumulator pressure on each row unit.

Select Menu >> Planter button >> Diagnostics button >> Tests tab (A).

4. Input selected row units for the accumulator test using the input boxes (D and E).

Test Complete appears on-screen when the accumulator test is completed without failures.

If a row unit fails the test, have your John Deere™ dealer replace the accumulator within the IRHD actuator.

John Deere is a trademark of Deere & Company WP29706,0000A2B -19-06APR17-1/1

25-16

020320

PN=95

Part Number Index

Adapter (61H1175) A—Thread Size

A95987 —UN—11APR17

Adapter (61H1174)

A95986 —UN—11APR17

Adapter (61H1163)

A95985 —UN—11APR17

Adapter (61H1162)

A95984 —UN—11APR17

Adapter (61H1160)

A95983 —UN—11APR17

A95982 —UN—11APR17

Adapters

Adapter (61H1178)

B—Thread Size

NOTE: Reference the provided table for the fitting thread sizes.

Thread Size Part Number

A (in)

B (in)

61H1160

9/16

11/16

61H1162

7/8

1

61H1163

1-1/16

1-3/16

61H1174

13/16

7/8

61H1175

13/16

1-1/16

61H1178

3/4

1-3/16

Continued on next page

30-1

LM78752,0000485 -19-30SEP19-1/3

020320

PN=96

Part Number Index

Adapter (61H1276) A—Thread Size

A105733 —UN—12SEP19

A95988 —UN—11APR17

LM78752,0000485 -19-30SEP19-2/3

Adapter (61M5013)

B—Thread Size Thread Size Part Number

A (in)

B (in)

61H1276

1-3/16

1-3/16

61M5013

1-3/16

1-3/16 LM78752,0000485 -19-30SEP19-3/3

45° Connector (61H1048) A—Thread Size

A95990 —UN—11APR17

A95989 —UN—11APR17

Connectors

45° Connector (61H1556)

B—Thread Size

NOTE: Reference the provided table for fitting thread sizes.

Thread Size Part Number

A (in)

B (in)

61H1048

1-3/16

1-1/16

61H1556

7/8

13/16 LM78752,0000486 -19-11APR17-1/1

30-2

020320

PN=97

Part Number Index

A99903 —UN—07MAR18

90° Elbow (61H1013)

A95971 —UN—10APR17

90° Elbow (61H1007)

A95970 —UN—10APR17

A95969 —UN—10APR17

Elbows

90° Swivel Elbow (61H1094)

90° Swivel Elbow (61H1095)

A105732 —UN—12SEP19

A95972 —UN—10APR17

90° Elbow (61H1052)

90° Swivel Elbow (61H1097) A—Thread Size

A95974 —UN—10APR17

A95973 —UN—10APR17

90° Swivel Elbow (61H1096)

45° Elbow (61H1312)

B—Thread Size Continued on next page

30-3

LM78752,0000483 -19-30SEP19-1/4

020320

PN=98

Part Number Index NOTE: Reference the provided table for fitting thread sizes.

Thread Sizes Part Number

A (in)

B (in)

61H1007

1-1/16

1-3/16

61H1013

1-1/16

13/16

61H1052

1-5/16

13/16

61H1094

11/16

11/16

61H1095

13/16

13/16

61H1096

1

1

61H1097

1-3/16

1-3/16

61H1312

11/16

11/16

Continued on next page

30-4

LM78752,0000483 -19-30SEP19-2/4

020320

PN=99

45° Elbow (A90125) A—Thread Size

A95980 —UN—11APR17

90° Elbow (61H3012)

A95979 —UN—11APR17

45° Elbow (61H1490)

A95978 —UN—11APR17

90° Elbow (61H1393)

A95977 —UN—11APR17

90° Elbow (61H1323)

A95976 —UN—11APR17

A95975 —UN—11APR17

Part Number Index

45° Elbow (A90850)

B—Thread Size Thread Sizes Part Number

A (in)

B (in)

61H1323

13/16

13/16

61H1393

11/16

11/16

61H1490

1-3/16

1-3/16

61H3012

7/8

13/16

A90125

7/8

7/8

A90850

3/4

3/4

Continued on next page

LM78752,0000483 -19-30SEP19-3/4

30-5

020320

PN=100

Part Number Index

B—Thread Size

A95981 —UN—11APR17

A—Thread Size

90° Swivel Elbow (AH89069) Thread Sizes Part Number

A (in)

B (in)

AH89069

7/16

7/16 LM78752,0000483 -19-30SEP19-4/4

30-6

020320

PN=101

Part Number Index

A95992 —UN—12APR17

A95991 —UN—12APR17

Plugs

Plug (61H1147)

Plug (64H5017)

A95993 —UN—12APR17

NOTE: Reference the provided table for fitting thread sizes.

Plug (AT361540) A—Thread Size

Part Number

Thread Size A (in)

61H1147

13/16

64H5017

9/16

AT361540

7/8 LM78752,0000487 -19-12APR17-1/1

30-7

020320

PN=102

Part Number Index

A95995 —UN—12APR17

A95994 —UN—12APR17

Quick Couplers

A95997 —UN—12APR17

Quick Coupler (AA59671)

A95996 —UN—12APR17

Quick Coupler (AA59411)

Quick Coupler (AH220366)

Quick Coupler (AA89749)

A95998 —UN—12APR17

NOTE: Reference the provided table for fitting thread sizes.

Quick Coupler (AR94522) A—Thread Size

Part Number

Thread Size A (in)

AA59411

3/4

AA59671

3/4

AH220366

9/16

AA89749

11/16

AR94522

3/4 LM78752,0000488 -19-17AUG18-1/1

30-8

020320

PN=103

Part Number Index

Reducers

A95999 —UN—12APR17

NOTE: Reference the provided table for fitting thread sizes.

Reducer (61H1481) A—Thread Size

Thread Size Part Number

A (in)

B (in)

61H1481

11/16

13/16 LM78752,0000489 -19-12APR17-1/1

30-9

020320

PN=104

Part Number Index

A96099 —UN—12APR17

A96098 —UN—12APR17

T-Fittings

A96101 —UN—12APR17

T-fitting (61H1030)

A96100 —UN—12APR17

T-fitting (61H1023)

A96103 —UN—12APR17

T-fitting (61H1291)

A96102 —UN—12APR17

T-fitting (61H1205)

T-fitting (61H1292)

T-fitting (61H1496)

NOTE: Reference the provided table for fitting thread sizes.

Thread Size Part Number

A (in)

B (in)

C (in)

61H1023

9/16

11/16

11/16

61H1030

11/16

11/16

11/16

61H1205

11/16

11/16

11/16

61H1291

11/16

11/16

11/16

61H1292

13/16

13/16

13/16

61H1496

11/16

13/16 Continued on next page

30-10

11/16 LM78752,0000484 -19-07MAR18-1/4

020320

PN=105

A96104 —UN—12APR17

A99904 —UN—07MAR18

Part Number Index

A96105 —UN—12APR17

T-fitting (A88948)

A96108 —UN—12APR17

T-fitting (61M5416)

A96107 —UN—12APR17

T-fitting (61H1554)

A96106 —UN—12APR17

T-Fitting (61H1505)

T-fitting (61H1503)

T-fitting (A88950)

A96109 —UN—12APR17

NOTE: Reference the provided table for fitting thread sizes.

T-fitting (AE45056)

Continued on next page

30-11

LM78752,0000484 -19-07MAR18-2/4

020320

PN=106

Part Number Index Thread Size Part Number

A (in)

B (in)

C (in)

11/16

11/16

11/16

61H1505

13/16

13/16

13/16

61H1554

13/16

11/16

11/16

61M5416

11/16

11/16

13/16

A88948

3/4

9/16

3/4

A88950

3/4

9/16

9/16

AE45056

7/16

7/16

7/16

Cross Fitting (KK21790)

A96113 —UN—12APR17

T-fitting (H75415)

A96112 —UN—12APR17

T-fitting (AN33434)

A96111 —UN—12APR17

A96110 —UN—12APR17

61H1503

Cross Fitting (61H1504)

A99905 —UN—07MAR18

NOTE: Reference the provided table for fitting thread sizes.

T-Fitting (AA82786)

Continued on next page

30-12

LM78752,0000484 -19-07MAR18-3/4

020320

PN=107

Part Number Index Thread Size Part Number

A (in)

B (in)

C (in)

AN33434

3/4

3/4

3/4

H75415

7/8

3/4

3/4

AA82786

9/16

9/16

3/4

KK21790

13/16

13/16

13/16

61H1504

13/16

13/16

13/16

D (in)

13/16 13/16 LM78752,0000484 -19-07MAR18-4/4

A96096 —UN—12APR17

A96000 —UN—12APR17

Unions

Union (61H1275)

Union (61H1285)

A96097 —UN—12APR17

NOTE: Reference the provided table for fitting thread sizes.

Union (R27238) A—Thread Size

B—Thread Size

Thread Size Part Number

A (in)

B (in)

61H1275

13/16

13/16

61H1285

11/16

11/16

R27238

9/16

9/16 LM78752,000048A -19-12APR17-1/1

30-13

020320

PN=108

Part Number Index

A96118 —UN—13APR17

Plate (A106002)

A105734 —UN—12SEP19

Plate (A105998)

A96117 —UN—13APR17

Plate (A104518)

A96116 —UN—13APR17

Bracket (A91622)

A96115 —UN—13APR17

A96114 —UN—13APR17

Brackets

A105751 —UN—01OCT19

A96119 —UN—13APR17

Plate (A106542)

Bracket (A116901)

Plate (A106825)

Bracket (A122225) Continued on next page

30-14

LM78752,000048B -19-01OCT19-1/2

020320

PN=109

Bracket (AA87147)

A96125 —UN—13APR17

Bracket (AA87146)

A96124 —UN—13APR17

Plate (A107255)

A96123 —UN—13APR17

Plate (A106827)

A96122 —UN—13APR17

Plate (A106826)

A96121 —UN—13APR17

A96120 —UN—13APR17

Part Number Index

Plate (AA89168) LM78752,000048B -19-01OCT19-2/2

30-15

020320

PN=110

Part Number Index

30-16

020320

PN=111

Part Number Index

30-17

020320

PN=112