DOWNLOAD PDF Bobcat 873 Operation & Maintenance Manual SN 514123810 thru 514139999

Operation & Maintenance Manual S/N 514123810 thru 514139999 S/N 514222300 thru 514239999

EQUIPPED WITH BOBCAT INTERLOCK CONTROL SYSTEM (BICSTM) 6900791 (7–99) Revised (9–00)

Printed in U.S.A.

© Bobcat Company 2000

OPERATOR SAFETY WARNINGS CORRECT Operator must have instructions before running the machine.

Untrained operators can cause injury or death.

W–2001–1285 B–10731

Safety Alert Symbol: This symbol with a warning statement, means: “Warning, be alert! Your safety is involved!” Carefully read the message that follows.

Never use the loader without instructions. See machine signs

CORRECT

WRONG

CORRECT

(decals), Operation & Maintenance

Manual and Handbook.

B–7403

B–13552

B–13553

Always use the seat bar and fasten seat belt snugly.

Always keep feet on the pedals or foot rest when operating loader.

Never use loader without operator cab with ROPS and FOPS approval. Fasten your seat belt.

Never use loader as man lift or elevating device for personnel.

WRONG

WRONG

WRONG

B–6578

B–13554

B–13555

Keep bystanders away from work area.

Always carry bucket or attachments as low as possible.

Do not travel or turn with lift arms up.

Load, unload and turn on flat level ground.

WRONG

WRONG

WRONG

B–6587

B–13557

B–13558

Never exceed rated operating capacity.

Never leave loader with engine running or with lift arms up.

To park, engage parking brake and put attachment flat on the ground.

Do not use loader in atmosphere with explosive dust or gas or where exhaust can contact flammable material.

Never carry riders.

Never modify equipment.

Use only attachments approved

by Bobcat Company for this model loader.

SAFETY EQUIPMENT The Bobcat loader must be equipped with safety items necessary for each job. Ask your dealer about attachments and accessories.

1. SEAT BELT: Check belt fasteners and check for damaged webbing or buckle.

2. SEAT BAR: When up, it must lock the pedals.

3. OPERATOR CAB (ROPS and FOPS): It must be on the loader with all fasteners tight.

4. HANDBOOK: Must be in the cab.

5. SAFETY SIGNS (DECALS): Replace if damaged.

6. SAFETY TREADS: Replace if damaged.

7. GRAB HANDLES: Replace if damaged.

8. LIFT ARM SUPPORT DEVICE: Replace if damaged.

9. PARKING BRAKE OSW01–0600 10. BOBCAT INTERLOCK CONTROL SYSTEM (BICS™)

CONTENTS FOREWORD FOREWORD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix OPERATING INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 PREVENTIVE MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 SYSTEMS ANALYSIS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 MACHINE SIGN TRANSLATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89

SAFETY

OPERATING INSTRUCTIONS

CALIFORNIA PROPOSITION 65 WARNING Diesel engine exhaust and some of its constituents are known to the State of California to cause cancer, birth defects and other reproductive harm.

PREVENTIVE MAINTENANCE

REFERENCE INFORMATION Write the correct information for YOUR Bobcat loader in the spaces below.

Always use these numbers when referring to your Bobcat loader.

Loader Serial Number . . . . . . .

Engine Serial Number . . . . . . .

SYSTEMS ANALYSIS

MACHINE SIGN TRANSLATIONS

SPECIFICATIONS

NOTES:

YOUR LOADER DEALER: ADDRESS: PHONE: Bobcat Company P.O. Box 128 Gwinner, ND 58040–0128 Bobcat Company Europe J. Huysmanslaan 59 B–1651 LOT BELGIUM

i

873 Bobcat Loader Operation & Maintenance Manual

Bobcat Company is ISO 9001 certified ISO 9001 is a set of international standards that control the processes and procedures which we use to design, develop, manufacture, distribute, and service Bobcat products.

British Standards Institute (BSI) is the Certified Registrar Bobcat Company chose to assess the Company’s compliance with the ISO 9001 set of standards. The BSI registration certifies that the two Bobcat Company manufacturing plants and the Bobcat Company corporate offices (Gwinner, Bismarck & West Fargo) in North Dakota are in compliance with ISO 9001. Only certified assessors, like BSI, can grant registrations. Since registration requires this third–party auditing, it is irrefutable evidence of conformance. Continued certification is subject to periodic audits.

ISO 9001 means that as a company we say what we do and do what we say. In other words, we have established procedures and policies, and we provide evidence that the procedures and policies are followed.

What does ISO 9001 mean to Bobcat Customers? It means that Bobcat Company produces your Bobcat loader, excavator, and attachments with strict attention to details, using the latest technology and proven techniques.

REGULAR MAINTENANCE ITEMS 6665603

ENGINE OIL FILTER

6667352

FUEL FILTER

6666375

AIR CLEANER, OUTER

6666376

AIR CLEANER, INNER

6661248

HYDROSTATIC FILTER

6665427

BATTERY

6724094

PROPYLENE GLYCOL ANTI–FREEZE, Premixed [–34°F (–37°C)]

6724354

PROPYLENE GLYCOL ANTI–FREEZE, Concentrate

6563328

BLACK GOLD Hydraulic/Hydrostatic Fluid – 5 Gallons

6657299

MOTOR OIL 15W40 CE/SG – 1 Qt.

6657301

MOTOR OIL 10W30 CE/SG – 1 Qt.

6657303

MOTOR OIL 30 CE/SG – 1 Qt.

ii

873 Bobcat Loader Operation & Maintenance Manual

FOREWORD FOREWORD This Operation & Maintenance Manual was written to give the owner/operator instructions on the safe operation and maintenance of the Bobcat loader. READ AND UNDERSTAND THIS OPERATION & MAINTENANCE MANUAL BEFORE OPERATING YOUR LOADER. If you have any questions, see your Bobcat loader dealer.

SERIAL NUMBER LOCATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v DELIVERY REPORT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v BOBCAT LOADER IDENTIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi OPTIONS AND ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii

iii

873 Bobcat Loader Operation & Maintenance Manual

iv

873 Bobcat Loader Operation & Maintenance Manual

SERIAL NUMBER LOCATIONS

A

Always use the serial number of the loader when requesting service information or when ordering parts.

Early or later models (identification made by serial number) may use different parts, or it may be necessary to use a different procedure in doing a specific service operation.

LOADER SERIAL NUMBER The loader serial number plate is located on the outside of the loader frame [A].

Explanation of loader Serial Number: XXXX

P–10085

XXXXX Module 2. – Production Sequence (Series)

B

Module 1. – Model/Engine Combination 1. The four digit Model/Engine Combination Module number identifies the model number and engine combination.

2. The five digit Production Sequence Number identifies the order which the loader is produced.

ENGINE SERIAL NUMBER P–10443

The engine serial number is located on the valve cover at the right side of the engine [B].

DELIVERY REPORT

C

The Delivery Report must be filled out by the dealer and signed by the owner or operator when the Bobcat loader is delivered. An explanation of the form must be given to the owner. Make sure it is filled out completely [C].

v

873 Bobcat Loader Operation & Maintenance Manual

BOBCAT LOADER IDENTIFICATION ◊ FRONT LIGHTS

OPERATOR SEAT

GRAB HANDLES ◊ REAR AUXILIARY QUICK COUPLERS

SEAT BELT

TILT CYLINDER ◊ FRONT AUXILIARY QUICK COUPLERS

BUCKET

SAFETY TREAD BUCKET STEPS OPERATOR CAB (ROPS & FOPS)

LIFT ARM SUPPORT DEVICE

SEAT BAR REAR GRILL

LIFT ARM

LIFT CYLINDER

◊ REAR LIGHT

REAR DOOR

◊ TAIL LIGHT

* TIRES

B–15002 B–15003

◊ OPTIONAL OR FIELD ACCESSORY (Not Standard Equipment) * TIRES – Flotation tires ◊ are shown. The Bobcat loader is factory equipped with standard tires.

BUCKET – Several different buckets and other attachments are available for the Bobcat loader.

ROPS, FOPS – Roll Over Protective Structure, per SAE J1040 and ISO 3471, and Falling Object Protective Structure per SAE J1043 and ISO 3449, Level l. Level ll is available. The Bobcat loader is base–equipped with a standard operator cab as shown. Extra insulated cab is available as an option (Reduced noise level). vi

873 Bobcat Loader Operation & Maintenance Manual

OPTIONS AND ACCESSORIES Model 873 Bobcat loaders are equipped with the following Standard items: Bob–Tach Spark Arrestor Exhaust System (Turbo Charger) Lift Arm Support Device Operator Cab (with ROPS & FOPS Approval) Bobcat Interlock Control System (BICS™) Seat Belt Seat Bar Parking Brake Gauges/Warning Lights Glow Plug Preheat system Tires, 12–16.5, 10PR Bobcat Heavy Duty Below is a list of some equipment available as a Factory Installed Option or as a Field Installed Accessory from your Bobcat Loader dealer. See your Bobcat dealer for other available accessories and attachments.

Tires 31 x 15.5–15, 8PR Ultra Grip Tread . . . . .

8.25 x 15 Air Boss Segmented Tires . . . .

12 x 16.5 Air Boss Segmented Tires . . . .

Instrumentation Opt. & FA FA FA

Opt. FA

Hydraulics

Operator Cab Sound Cab (Reduces Noise at Operator’s Ear) . . . . . . . . . . . . . . . . . . . .

Deluxe Cab . . . . . . . . . . . . . . . . . . . . . . . . . .

Operating Lights (Front & Rear) . . . . . . . .

Horn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Back–up Alarm . . . . . . . . . . . . . . . . . . . . . . .

Top Window . . . . . . . . . . . . . . . . . . . . . . . . .

Rear Window . . . . . . . . . . . . . . . . . . . . . . . .

Cab Enclosure and Heater . . . . . . . . . . . . .

Vinyl Cab Enclosure . . . . . . . . . . . . . . . . . .

Hand Control Conversion . . . . . . . . . . . . . .

Cover Kit (Pedals Area) . . . . . . . . . . . . . . .

Cover Kit (Hydraulic Reservoir Area) . . . .

Fire Extinguisher . . . . . . . . . . . . . . . . . . . . .

Flasher Lights . . . . . . . . . . . . . . . . . . . . . . . .

Strobe or Rotating Beacon Light . . . . . . . .

3’’ Seat Belt . . . . . . . . . . . . . . . . . . . . . . . . .

Special Applications Kit* . . . . . . . . . . . . . . .

Suspension Seat . . . . . . . . . . . . . . . . . . . . .

Rear Window Wiper . . . . . . . . . . . . . . . . . .

Large Operator Seat Bar Kit . . . . . . . . . . .

Bobcat Operation Sensing System (BOSS®) . . . . . . . . . . . . . . . . . .

Keyless Start System . . . . . . . . . . . . . . . . .

Opt. Opt. & FA Opt. & FA FA Opt. & FA FA FA Opt. & FA FA Opt. & FA FA FA FA FA FA FA FA Opt. & FA FA FA

Front Auxiliary Hydraulics . . . . . . . . . . . . .

Rear Auxiliary Hydraulics . . . . . . . . . . . . . .

Hydraulic Bucket Positioning (Includes On/Off Selection) . . . . . . . . . .

Opt. & FA Opt. & FA Opt. & FA

Other Catalytic Exhaust Purifier . . . . . . . . . . . . . .

Engine Heater (Oil Pan) . . . . . . . . . . . . . . .

Four Point Lift . . . . . . . . . . . . . . . . . . . . . . . .

Locking Fuel Cap . . . . . . . . . . . . . . . . . . . . .

Radiator Screen Kit . . . . . . . . . . . . . . . . . . .

Rear Door Bumpers . . . . . . . . . . . . . . . . . .

Tailgate Lock . . . . . . . . . . . . . . . . . . . . . . . .

Tool Box . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Counterweight Kit . . . . . . . . . . . . . . . . . . . .

Opt. & FA FA FA FA FA FA FA FA Opt. & FA

Opt. = Factory Installed Option FA = Field Accessory N/A = Not Available * Includes 1/2 inch Lexan Front Door; 1/4 inch Lexan Top & Rear Windows

Specifications subject to change without notice

vii

873 Bobcat Loader Operation & Maintenance Manual

viii

873 Bobcat Loader Operation & Maintenance Manual

SAFETY SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xi, xii FIRE PREVENTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiii MACHINE SIGNS (DECALS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiv, xv

ix

SAFETY

873 Bobcat Loader Operation & Maintenance Manual

x

873 Bobcat Loader Operation & Maintenance Manual

SAFETY INSTRUCTIONS FOR BOBCAT SKID–STEER LOADERS AND ATTACHMENTS SAFETY IS THE OPERATOR’S RESPONSIBILITY All Bobcat loaders and attachments are designed to give maximum safety, but no machine design can prevent operator error or carelessness.

The Bobcat skid–steer loader is highly maneuverable and compact. It is rugged and useful under a wide variety of conditions.

This presents an operator with hazards associated with off highway, rough terrain applications, common with Bobcat loader usage.

The Bobcat loader has an internal combustion engine with resultant heat and exhaust. All exhaust gases can kill or cause illness so use the loader with adequate ventilation. The loader has a spark arrestor exhaust system or muffler which is required for operation in certain areas.

The dealer explains the capabilities and restrictions of the Bobcat loader and attachments for each application. The dealer demonstrates the safe operation according to Bobcat instructional materials, which are also available to operators. The dealer can also identify unsafe modifications or use of unapproved attachments. The attachments and buckets are designed for a Rated Operating Capacity (some have restricted lift heights) and secure fastening to the Bobcat loader. The user must check with the dealer, or Bobcat literature, to determine safe loads of materials of specified densities for the loader–attachment combination.

The following publications and training materials provide information on the safe use and maintenance of the Bobcat loader and attachments:

• The Delivery Report is used to assure that complete instructions have been given to the new owner and that the Bobcat loader and attachment is in safe operating condition.

• The Operation & Maintenance Manual delivered with the Bobcat loader or attachment gives operating information as well

as routine maintenance and service procedures. It is a part of the machine and can be stored in a container provided inside the cab of the loader. Replacement Operation & Maintenance Manuals can be ordered from your Bobcat dealer.

• Machine signs (decals) instruct on the safe operation and care of your Bobcat loader or attachment. The signs and their locations are shown in the Operation & Maintenance Manual. Replacement signs are available from your Bobcat dealer.

• An Operator’s Handbook is fastened to the operator cab of the loader. Its brief instructions are convenient to the operator.

The Handbook is available from your dealer in an English edition or one of many other languages. See your Bobcat dealer for more information on translated versions.

• The Safety Manual delivered with the Bobcat loader gives general safety information.

• Operator Training Courses are available from your local Bobcat dealer. They provide information for safe and efficient operation of the Bobcat loader and some attachments. The courses are available in English and Spanish versions.

• Service Safety Training Courses are available from your Bobcat dealer. They provide information for safe and correct service procedures.

• See the ADDITIONAL PUBLICATIONS Page in this manual or your Bobcat dealer for Service and Parts Manuals, printed materials, videos, or training courses available. Also check the Bobcat web site www.bobcat.com

The dealer and owner/operator review the recommended uses of the product when delivered. If the owner/operator will be using the machine for a different application(s) he must ask the dealer for recommendations on the new use.

Call Before You Dig 1–888–258–0808 When you call, you will be directed to a location in your state/ city for information about buried lines (telephone, cable TV, water, sewer, gas, etc.)

SI01–0400

xi

873 Bobcat Loader Operation & Maintenance Manual

BEFORE OPERATING THE BOBCAT LOADER Safety Alert Symbol This symbol with a warning statement means: “Warning, be alert! Your safety is involved!” Carefully read the message that follows.

Operator must have instructions before running the machine. Untrained operators can cause injury or death.

W–2001–1285

The Bobcat loader and attachment must be in good operating condition before use.

Check all of the items on the Bobcat Service Schedule Decal under the 8–10 hour column or as shown in this Manual.

SAFE OPERATION NEEDS A QUALIFIED OPERATOR * A QUALIFIED OPERATOR MUST DO THE FOLLOWING: • UNDERSTAND THE WRITTEN INSTRUCTIONS, RULES AND REGULATIONS

This notice identifies procedures which must be followed to avoid damage to the machine.

I–2019–0284

• The written instructions from Bobcat Company

include the Delivery Report, Operation & Maintenance Manual, Operator’s Handbook, Safety Manual and machine signs (decals).

• Check the rules and regulations at your location. The

rules may include an employer’s work safety requirements. Regulations may apply to local driving requirements or use of a Slow Moving Vehicle (SMV) emblem. Regulations may identify a hazard such as a utility line.

Warnings on the machine and in the manuals are for your safety. Failure to obey warnings can cause injury or death.

W–2044–1285

• HAVE TRAINING WITH ACTUAL OPERATION • Operator training must consist of a demonstration and verbal instruction. This training is given by your Bobcat dealer before the product is delivered.

• The new operator must start in an area without bystanders and use all the controls until he can operate the machine and attachment safely under all conditions of the work area. Always fasten seat belt before operating.

• Operator Training Courses are available from your Bobcat dealer in English and Spanish. They provide information for safe and efficient equipment operation. Safety videos are also available.

• Service Safety Training Courses are available from your Bobcat dealer. They provide information for safe and correct service procedures.

• KNOW THE WORK CONDITIONS • Know the weight of the materials being handled. Avoid exceeding the Rated Operating Capacity of the machine. Material which is very dense will be heavier than the same volume of less dense material. Reduce the size of load if handling dense material.

• The operator must know any prohibited uses or work areas, for example, he needs to know about excessive slopes.

• Know the location of any underground lines. Call local utilities or the TOLL FREE phone number found in the SAFETY INSTRUCTIONS Section of this manual.

• Wear tight fitting clothing. Always wear safety glasses when doing maintenance or service. Safety glasses, hearing protection or special applications kit are required for some work. See your dealer about Bobcat Safety equipment.

* For an operator be qualified, he must not use drugs or alcoholic drinks which impair his alertness or coordination while working. An operator who is taking prescription drugs must get medical advice to determine if he can safely operate a machine.

SI02–0400

xii

873 Bobcat Loader Operation & Maintenance Manual

FIRE PREVENTION The machines and some attachments have components that are at high temperatures under normal operating conditions.

The primary source of high temperatures is the engine and exhaust system. The electrical system, if damaged or incorrectly maintained, can be a source of arcs or sparks.

Flammable debris (leaves, straw, etc.) must be removed regularly. If flammable debris is allowed to accumulate, it can cause a fire hazard. Clean often to avoid this accumulation. Flammable debris in the engine compartment is a potential fire hazard.

The spark arrestor exhaust system (if equipped) is designed to control the emission of hot particles from the engine and exhaust system, but the muffler and the exhaust gases are still hot.

• Do not use the machine where exhaust, arcs, sparks or hot components can contact flammable material, explosive dust or gases.

• The operator cab, engine compartment and engine cooling system must be inspected every day and cleaned if necessary to prevent fire hazards and overheating.

• Check all electrical wiring and connections for damage. Keep the battery terminals clean and tight. Repair or replace any damaged part.

• Check fuel and hydraulic tubes, hoses and fittings for damage and leakage. Never use open flame or bare skin to check for leaks. Tighten or replace any parts that show leakage. Always clean fluid spills. Do not use gasoline or diesel fuel for cleaning parts. Use commercial nonflammable solvents.

• Do not use ether or starting fluids on any engine which has glow plugs. These starting aids can cause explosion and injure you or bystanders.

• Always clean the machine, disconnect the battery, and disconnect the wiring from the electronic controllers before welding.

Cover rubber hoses, battery and all other flammable parts. Keep a fire extinguisher near the machine when welding. Have good ventilation when grinding or welding painted parts. Wear dust mask when grinding painted parts. Toxic dust or gas can be produced.

• Stop the engine and let it cool before adding fuel. No smoking!

• Use the procedure in the Operation & Maintenance Manual for connecting the battery and for jump starting.

• Use the procedure in the Operation & Maintenance Manual for cleaning the spark arrestor muffler (if equipped).

• Know where fire extinguishers and first aid kits are located and how to use them. Fire extinguishers are available from your Bobcat dealer.

SI03–0400

xiii

873 Bobcat Loader Operation & Maintenance Manual

MACHINE SIGNS (DECALS) Follow the instructions on all the Machine Signs (Decals) that are on the loader. Replace any damaged machine signs and be sure they are in the correct locations. Machine signs are available from your Bobcat loader dealer.

6703723 (Foot Pedal) 6703724 (Hand Control) 6727452 (Later Models w/Float button) OPERATION INSTRUCTIONS TO OPERATE LOADER: 1. Fasten seat belt and lower seat bar.

2. Start engine.

3. Activate green “PRESS TO OPERATE” button on left instrument panel.

NOTE: Activate “PRESS TO OPERATE” button again if seat bar is raised and lowered or key is turned off.

See Operation & Maintenance Manual and Handbook for more instructions.

6717640

6715944

6705720 6715940 (Advanced Hand Control) 6703724 (Mechanical Hand Control)

6708021 Foot Pedal 6708158 Hand Control

OPERATION INSTRUCTIONS FOR LOADERS WITH ADVANCED HAND CONTROLS (AHC) TO OPERATE LOADER: 1. Fasten seat belt and lower seat bar.

2. Put hand controls in neutral.

3. Start engine.

4. Activate green “PRESS TO OPERATE” button on left instrument panel.

• Both green lights on left hand control must be on.

• If hydraulic functions do not operate, stop engine.

Check that both hand controls are in the neutral position. Re–start engine.

NOTE: Activate “PRESS TO OPERATE” button again if seat bar is raised and lowered or key is turned off.

See Operation & Maintenance Manual and Handbook for more instructions.

6713715 6717639 (Advanced Hand Control Only)

6703726 (Mechanical Hand Control Only)

6577754 (3)

6709452 6711840 6557565

6579510 Foot Pedal 6703725 Hand Control

6561383

*6579528

6710358 6579509

6579639

* Decal located behind lift arm crossmember.

B–15003

xiv

873 Bobcat Loader Operation & Maintenance Manual

MACHINE SIGNS (DECALS) (Cont’d)

863/873

THIS MODEL LOADER IS FACTORY EQUIPPED WITH A U.S.D.A. FORESTRY SERVICEAPPROVEDSPARKARRESTOREXHAUSTSYSTEM. THE TURBOCHARGER MUST OPERATE TO KEEP THE SPARK ARRESTOR EXHAUSTSYSTEM IN WORKING CONDITION. IF THIS MACHINE IS OPERATED ON FLAMMABLE FOREST, BRUSH OR GRASS COVERED LAND, IT MUST BE EQUIPPED WITH A SPARK ARRESTOR ATTACHED TO THE EXHAUST SYSTEM AND MAINTAINEDIN WORKING ORDER. FAILURE TO DO DO WILL BE IN VIOLATION OF CALIFORNIA STATELAW,SECTION4442.PRC REFER TO LOCAL LAWS AND REGULATIONS FOR SPARK ARRESTOR REQUIREMENTS. SEETHE OPERATION ANDMAINTENANCEMANUALFORMOREINSTRUCTIONS.

SW97 6708937

6578368

6708937 6708820

6717343 (2) Under Cab 6595014 (2)

6595014 (2)

6708941

6718398

6707786

Located inside the engine compartment.

B–15002

xv

873 Bobcat Loader Operation & Maintenance Manual

xvi

873 Bobcat Loader Operation & Maintenance Manual

OPERATING INSTRUCTIONS ATTACHMENTS AND BUCKETS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Installing The Bucket Or Attachment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Removing The Bucket Or Attachment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 BOBCAT INTERLOCK CONTROL SYSTEM (BICS™) . . . . . . . . . . . . . . . . . . 6 Auxiliary Hydraulic System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Lift Arm By–Pass Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Traction Lock Override . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 DAILY INSPECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 ENGINE SPEED CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

OPERATING INSTRUCTIONS

GETTING READY FOR OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 HYDRAULIC CONTROLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Advanced Hand Controls (If Equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Attachment Functions Control (If Equipped) . . . . . . . . . . . . . . . . . . . . . . . . . 17 Auxiliary Hydraulics (If Equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Auxiliary Hydraulics Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Continuous Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Disengage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Momentary Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Bucket Position Valve Operation (If Equipped) . . . . . . . . . . . . . . . . . . . 13, 14 Foot Pedals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Lift Arm Float Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Lift Arm Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Tilt Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Front Auxiliary Hydraulics Continuous Operation . . . . . . . . . . . . . . . . . . . . . 16 Front Auxiliary Hydraulics Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Hand Controls (Mechanical And Advanced Hand Controls) . . . . . . . . . . . . 14 Lift Arm Float Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Lift Arm Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Tilt Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Rear Auxiliary Hydraulics Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Relieving Hydraulic Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Quick Couplers (Flush Face) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 BOSS™ Optional Display Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 With BOSS™ Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Side Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Without BOSS™ Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Side Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 LIFTING THE LOADER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Four Point Lift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Continued On Next Page 1

873 Bobcat Loader Operation & Maintenance Manual

OPERATING INSTRUCTIONS (Cont’d) OPERATING PROCEDURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 OPERATING PROCEDURES (FOOT PEDALS) . . . . . . . . . . . . . . . . . . . . . . . 27 Backfilling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Digging Into The Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Emptying The Bucket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Filling The Bucket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Leveling The Ground (Using Lift Arms In Float Position) . . . . . . . . . . . . . . . 28 OPERATING PROCEDURES (HAND CONTROLS) . . . . . . . . . . . . . . . . . . . . 30 Backfilling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Digging Into The Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Emptying The Bucket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Filling The Bucket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Leveling The Ground (Using Lift Arms In Float Position) . . . . . . . . . . . . . . . 31 PARKING BRAKE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 PARKING THE BOBCAT LOADER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29, 32 SEAT BAR RESTRAINT SYSTEM (ADVANCED HAND CONTROLS) . . . . 12 SEAT BAR RESTRAINT SYSTEM (MECHANICAL HAND CONTROLS) . . 11 SEAT BAR RESTRAINT SYSTEM (FOOT PEDALS) . . . . . . . . . . . . . . . . . . . 11 STARTING THE ENGINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Cold Temperature Starting (With BOSS™) . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Cold Temperature Starting (Without BOSS™) . . . . . . . . . . . . . . . . . . . . . . . . 20 Normal Starting (With BOSS™) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Normal Starting (Without BOSS™) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Warming The Hydraulic/Hydrostatic System . . . . . . . . . . . . . . . . . . . . . . . . . 22 STEERING LEVERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Forward Travel, Reverse Travel, Normal Turning, Fast Turning . . . . . . . . . . 9 STOPPING THE BOBCAT LOADER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 STOPPING THE ENGINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 TOWING THE LOADER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 TRACTION LOCK CONTROL SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 TRANSPORTING THE BOBCAT LOADER . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

2

873 Bobcat Loader Operation & Maintenance Manual

INSTRUMENT PANEL 3.

Without BOSS® (Front Panel) [A]

A

1. TRACTION LOCK OVERRIDE BUTTON – (Functions Only When The Seat Bar Raised) Allows you to use the steering levers to move the loader when using the backhoe attachment or for loader service. (See Page 6.)

2. PRESS TO OPERATE BUTTON (Functions Only When The Seat Bar Is Down) – Activates BICS™ System when the Seat Bar is down and operator is seated in the operating position.

3. KEY SWITCH – For starting and stopping the engine.

4. TRANSMISSION WARNING LIGHT – Low transmission charge pressure, hydraulic filter needs replacement or high fluid temperature. Stop the engine if the light comes ON. 5. ENGINE WARNING LIGHT – Low engine oil pressure or high coolant temperature. Stop the engine if the light comes ON. 6. LIGHT SWITCH (Opt./FA) – Controls the available work and travel lights.

7. BUCKET LEVEL SWITCH (Opt./FA) – Controls the ON/OFF function of the available Bucket Position Valve, 8. PREHEAT BUTTON – For preheating the engine (glow plugs) before starting the engine.

9. HOURMETER – Records the total operating hours of the loader.

10. FUEL GAUGE – Shows the amount of fuel in the fuel tank.

11. VOLTMETER – Shows the condition of the battery and the rate of charge.

12. ENGINE TEMPERATURE GAUGE – Shows the engine coolant temperature.

13. AUXILIARY HYDRAULIC SWITCH (Opt./FA) – For engaging the available Auxiliary Hydraulics (front and rear).

6

Without BOSS

11 10

7

8 5

9

4 12

3 1

2

13 N–17061

P–10466

Side Console

B

2

1

3 P–10742

Without BOSS (Side Console•) [B] 1. REAR WIPER/WASHER (FA) – Controls operation of the available rear window wiper and washer.

2. HAZARD SWITCH / HAZARD INDICATORS (Opt./FA) – Controls the available hazard lights.

(Hazard Lights is a separate available accessory.)

Both panel indicators blink for hazard condition when the hazard switch is ON. A red light indicates fuse out for taillights, headlights, worklights, etc.

3. BEACON OR STROBE SWITCH (Opt./FA) – Controls the available flashing beacon or strobe light.

• Available only with Deluxe Cab or with Cab Enclosure

Kit. Opt. – Factory Installed Option FA – Field Installed Accessory – See your Bobcat loader dealer about available Field Accessories.

3

873 Bobcat Loader Operation & Maintenance Manual

INSTRUMENT PANEL 14.

With BOSS® (Front Panel) [A]

A

With BOSS

5 6

1. TRACTION LOCK OVERRIDE BUTTON – (Functions Only When The Seat Bar Is Raised) Allows you to use the steering levers to move the loader when using the backhoe attachment or for loader service. (See Page 6.)

2. PRESS TO OPERATE BUTTON (Functions Only When The Seat Bar Is Down) – Activates BICS™ System when the Seat Bar is down and operator is seated in the operating position.

3. KEY SWITCH – For starting and stopping the engine.

4. BOSS DIAGNOSTIC PORT – Connector for diagnostic tool to make service checks of the system operation unit and other components.

5. LIGHT SWITCH (Opt./FA) – Controls the available work and travel lights.

6. BUCKET LEVEL SWITCH (Opt./FA) – Controls the ON/OFF function of the available bucket Position Valve.

7. BOSS DISPLAY PANEL – Display panel for BOSS system and functions )See Page 5.)

8. AUXILIARY HYDRAULIC SWITCH (Opt./FA) – For engaging the available Auxiliary Hydraulics (front and rear).

4 3

PRESSTO OPERATE

1

7

2

8 N–16962

P–10489

Side Console

B

2

1

3 P–10742

With BOSS (Side Console•) [B] 1. REAR WIPER/WASHER (FA) – Controls operation of the available rear window wiper and washer.

2. HAZARD SWITCH / HAZARD INDICATORS (Opt./FA) – Controls the available hazard lights.

(Hazard Lights is a separate available accessory.)

Both panel indicators blink for hazard condition when the hazard switch is ON. A red light indicates fuse out for taillights, headlights, worklights, etc.

3. BEACON OR STROBE SWITCH (Opt./FA) – Controls the available flashing beacon or strobe light.

• Available only with Deluxe Cab or with Cab Enclosure

Kit. Opt. – Factory Installed Option FA – Field Installed Accessory – See your Bobcat loader dealer about available Field Accessories.

4

873 Bobcat Loader Operation & Maintenance Manual

INSTRUMENT PANEL (Cont’d)

A

BOSS Option Display Panel [A] 4.

1. FUEL LEVEL – Shows the amount of fuel in the tank. Flashing pump symbol indicates low fuel level.

(H2O symbol is non–functional.) (See WARNING SYMBOL) 2. BATTERY VOLTAGE – Shows the condition of the battery and charge rate. It will also indicate a WARNING for high or low voltage (See WARNING SYMBOL).

3. ENGINE OIL PRESSURE – Shows engine oil pressure. Flashing symbol indicates low oil pressure (See WARNING and SHUTDOWN SYMBOL).

4. ENGINE COOLANT TEMPERATURE / LEVEL – Shows engine coolant temperature and/or low coolant level (See WARNING and SHUTDOWN SYMBOL).

5. SHUTDOWN SYMBOL – This symbol is associated with any SHUTDOWN condition. When this symbol comes ON the SHUTDOWN will occur in 30 seconds. During SHUTDOWN the buzzer will sound continuously and the symbol will flash until the key switch is turned OFF.

1

5

NOTE: The engine can be restarted for 30–second periods to move the loader after a SHUTDOWN condition.

6. WARNING SYMBOL – The symbol will be ON when any WARNING or SHUTDOWN is activated.

The warning symbol is also used to indicate a WARNING if there is no related symbol on the display. During a WARNING, the buzzer will beep three times and the symbol will be ON continuously.

7. HOURMETER – Records the total operating hours of the loader. The five character code will display the operating hours to the nearest tenth. When WARNING or SHUTDOWN occurs, an alpha–numeric code will be displayed in the hourmeter area to inform the operator of the problem. (See SYSTEMS ANALYSIS, Page 73.)

During a WARNING or SHUTDOWN the hourmeter symbol is not visible.

8. CHARGE PRESSURE AND FILTER CONDITION – Flashing symbol indicates low fluid charge pressure (See SHUTDOWN SYMBOL). If arrows are ON with gear/drop, it is fluid charge pressure.

This symbol will also indicate a clogged hydraulic fluid filter.

9. AIR FILTER CONDITION – This symbol will indicate a clogged air filter element.

10. GLOW PLUG (Diesel) – The symbol will be ON when the glow plugs are energized. The hourmeter will also contain characters GLOXX where XX indicates the remaining time the glow plugs will be ON. Time remaining will count down in increments.

11. ENGINE SPEED – This symbol will indicate an engine overspeed (See WARNING and SHUTDOWN SYMBOL).

BRAKE INDICATOR LIGHT 12. PARKING (Non–Functional) .

13. HYDRAULIC FLUID TEMPERATURE – This symbol will indicate a high fluid temperature. (See WARNING or SHUTDOWN SYMBOL above).

2

4

3

7

6

8

9

12

13

10

11

MC–02320

5

873 Bobcat Loader Operation & Maintenance Manual

BOBCAT INTERLOCK CONTROL SYSTEM (BICS™)

A

The Bobcat Interlock Control System (BICS™) requires the operator to be seated in the operating position with the Seat Bar fully lowered and the green PRESS TO OPERATE Button activated before the lift, tilt and traction functions can be operated. The Seat Belt must be fastened anytime you operate the loader.

1 2 3 4

NOTE: Press the green PRESS TO OPERATE Button again if Seat Bar is raised and lowered or key is turned off.

5

The BICS controller is located inside the cab; behind and to the right of the operator’s seat [A].

There are five green lights on the BICS controller and all must be ON to operate the loader.

N–17979

The light functions are as follows [A]: 1. SYSTEM ACTIVATED – ON when the green PRESS TO OPERATE Button is activated.

2. SEAT BAR – ON when the seat bar is in down position.

3. VALVE – ON when lift and tilt hydraulic functions can be used.

4. TRACTION – ON when loader can be moved forward or backward.

AVOID INJURY OR DEATH

5. POWER – ON when the controller is operating correctly.

The Bobcat Interlock Control System (BICS) must deactivate the lift, tilt and traction drive functions. If it does not, contact your dealer for service. DO NOT modify the system.

NOTE: If any of the lights are off or blinking, see SYSTEMS ANALYSIS, BICS Troubleshooting Chart Page 77 or see BICS Inspection and Maintenance Instructions Page 48.

W–2151–0394

Lift Arm By–Pass Control

B

The lift arm by–pass control knob (Item 1) [B] is used to lower the lift arms if the lift arms can not be lowered during normal operating conditions.

With the operator in the seat, seat belt fastened and the seat bar fully lowered, turn the lift arm by–pass control knob (Item 1) [B] clockwise 1/4 turn. Then, pull up and hold the lift arm by–pass control until the lift arms slowly lower.

Traction Lock Override 14.

(Functions Only When The Seat Bar Is Raised) There is a traction lock override button (Item 1) [C] on the left hand instrument panel which will allow you to use the steering levers to move the loader forward & backward when using the backhoe attachment or for service.

1

• Press the button once to unlock traction drive (green

P–09707

traction light on BICS controller will be ON).

C • Press the button a second time to lock the traction drive (green traction light on BICS controller will be OFF).

NOTE: The Traction Lock Override button will unlock the traction drive when the operator is NOT in the seat and the seat bar is raised.

1

The Traction Lock Override button will function if brake pedal is in the engaged or disengaged position.

PRESS TO OPERATE

When the Traction Lock Override button is activated, the Traction Lock Control System will NOT engage the Traction Lock if the engine stops.

P–16964

6

873 Bobcat Loader Operation & Maintenance Manual

BOBCAT INTERLOCK CONTROL SYSTEM (BICS™) (Cont’d)

A

With BOSS

Auxiliary Hydraulic System When the operator is seated and raises the seat bar, the Auxiliary Hydraulic System will deactivate. Press the Auxiliary Hydraulics Switch (Item 1) [A] to reselect operating mode. (See HYDRAULIC CONTROLS, Auxiliary Hydraulics Page 18.)

1

P–10487

Before you leave the operator’s seat: • Lower the lift arms, put the attachment flat on the ground.

• Stop the engine.

• Engage the parking brake.

• Raise seat bar.

• (Foot Pedal Controls) Move pedals until both lock.

• (Mechanical Hand Controls) Move the hand controls until both lock.

The seat bar system must lock the lift and tilt controls in neutral when the seat bar is up.

Service the system if hand controls do not lock correctly.

• (Advanced Hand Controls) Move the hand controls to the NEUTRAL POSITION to make sure that both lift and tilt functions are deactivated.

The seat bar system must deactivate the lift and tilt control functions when the seat bar is up. Service the system if hand controls do not deactivate.

W–2323–0698

TRACTION LOCK CONTROL SYSTEM The Traction Lock Control System will lock the traction drive system when the engine stops.

NOTE: When the Traction Lock Override button is activated, the Traction Lock Control System will NOT engage the Traction Lock if the engine stops.

The Traction Lock Control System is incorporated into the BICS system.

See BICS Inspection & Maintenance Page 48.

NOTE: The traction light on the BICS controller will remain OFF until the engine is started and if the parking brake is disengaged.

7

873 Bobcat Loader Operation & Maintenance Manual

ENGINE SPEED CONTROL

A

The lever (Item 1) [A] is at the right side of the operator’s seat. Engine speed is controlled by moving the lever forward to increase the engine RPM and backward to decrease the engine RPM.

1

P–10565

B

PARKING BRAKE Engage the parking brake by pushing down on the top of the pedal [B]. The traction drive system will be locked.

MC–01914

P–03990

To release the parking brake, push down on the bottom of the pedal [C].

C

NOTE: If the loader will not move when operator is in the operating position with brake pedal released or when traction lock override button is pushed, move the steering levers either forward or backward a small amount to unlock the traction drive.

MC–01914

P–03989

8

873 Bobcat Loader Operation & Maintenance Manual

STEERING LEVERS

A 1

Before you leave the operator’s seat: • Lower the lift arms, put the attachment flat on the ground.

• Stop the engine.

• Engage the parking brake.

• Raise seat bar.

• (Foot Pedal Controls) Move pedals until both lock.

• (Mechanical Hand Controls) Move the hand controls until both lock.

The seat bar system must lock the lift and tilt controls in neutral when the seat bar is up.

Service the system if hand controls do not lock correctly.

P–05086

B

FORWARD

REVERSE

• (Advanced Hand Controls) Move the hand

controls to the NEUTRAL POSITION to make sure that both lift and tilt functions are deactivated.

The seat bar system must deactivate the lift and tilt control functions when the seat bar is up. Service the system if hand controls do not deactivate.

W–2323–0698

The steering levers (Item 1) [A] are on the right and left side in front of the seat (loader with foot pedals shown).

Move the levers slowly and smoothly. Avoid sudden starting and stopping.

LEFT TURN

RIGHT TURN

LEFT FAST TURN

RIGHT FAST TURN

The steering levers control forward and reverse travel and turning of the loader [B].

Forward Travel – Push both levers forward.

Reverse Travel – Pull both levers backward.

Normal Turning – Move one lever farther forward than the other.

Fast Turning – Push one lever forward and pull the other lever backward.

For slow travel speed, push the steering levers forward only a small amount.

To increase travel speed, push both levers farther forward.

For maximum pushing force, push the levers forward only a small amount with the engine at full RPM. STOPPING THE BOBCAT LOADER When the steering levers are moved to the neutral position the hydrostatic transmission will act as a service brake to stop the loader.

PI–01849

9

873 Bobcat Loader Operation & Maintenance Manual

SEAT BAR RESTRAINT SYSTEM (FOOT PEDALS)

A

The seat bar restraint system has a pivoting, spring assist seat bar (Item 1) [A] with arm rests and has spring loaded interlocks for the lift and tilt control pedals.

1

The operator controls the use of the seat bar. The seat bar in the down position helps to keep the operator in the seat.

The interlocks require the operator to lower the seat bar in order to operate the foot pedal controls.

When the seat bar is up, the lift and tilt control pedals are locked when returned to the NEUTRAL POSITION.

P–10430

AVOID INJURY OR DEATH

B

When operating the machine: • Keep the seat belt fastened snugly.

• The seat bar must be lowered.

• Keep your feet on the pedal controls.

SEAT BAR DOWN 2

Seat Bar

W–2046–0595

Before you leave the operator’s seat: • Lower the lift arms, put the attachment flat on the ground.

• Stop the engine.

• Engage the parking brake.

• Raise seat bar, move pedals until both lock.

1 Interlock

Pedal Linkage

W–2045–1086

3

The seat bar system must lock the lift and tilt control pedals in neutral when the seat bar is up. Service the system if pedals do not lock correctly.

Interlock Shield

W–2105–1285 MC–01668

The spring loaded interlocks (Item 1) [B] control the locking and unlocking functions of the Foot Pedal controls.

C

SEAT BAR RAISED Seat Bar

The interlocks (Item 1) [B] require the operator to lower the seat bar (Item 2) [B] which allows the operator to move the foot pedals to control the lift and tilt functions.

When the seat bar is lowered, it pushes the interlock (Item 1) [B] down on both sides, releasing the pedal linkages (Item 3) [B] from the interlocks.

Interlock

The pedals will pivot in both directions when the interlock is down.

When the seat bar is raised, spring forces raise the interlocks [C].

Interlock Shield

The foot pedals will not pivot when the interlock is up.

Refer to SEAT BAR RESTRAINT SYSTEM Inspecting and Maintaining The Seat Bar Page 45.

MC–01668

10

873 Bobcat Loader Operation & Maintenance Manual

SEAT BAR RESTRAINT SYSTEM (MECHANICAL HAND CONTROLS)

A

The seat bar restraint system has a pivoting seat bar (Item 1) [A] with arm rests and has spring loaded interlocks for the lift and tilt control functions.

1

The operator controls the use of the seat bar. The seat bar in the down position helps to keep the operator in the seat.

The interlocks require the operator to lower the seat bar in order to operate the hand controls.

When the seat bar is up, the lift and tilt control functions are locked when returned to the NEUTRAL POSITION.

P–03563

SEAT BAR DOWN

B

AVOID INJURY OR DEATH

2

When operating the machine: • Keep the seat belt fastened snugly.

• The seat bar must be lowered.

• Keep your feet on the foot rests.

Seat Bar

W–2179–0694

Before you leave the operator’s seat: • Lower the lift arms, put the attachment flat on the ground.

• Stop the engine.

• Engage the parking brake.

• Raise seat bar, move hand controls until both lock.

The seat bar system must lock the lift and tilt control in neutral when the seat bar is up.

Service the system if hand controls do not lock correctly.

1 Hand Control Linkage

3

Interlock Interlock Shield

W–2153–0594 MC–01950

SEAT BAR RAISED

C

The spring loaded interlocks (Item 1) [B] control the locking and unlocking functions of the hand controls.

Seat Bar

The interlocks (Item 1) [B] require the operator to lower the seat bar (Item 2) [B] which allows the operator to move the hand controls to control the lift and tilt functions.

When the seat bar is lowered, it pushes the interlock (Item 1) [B] down on both sides, releasing the hand control linkages (Item 3) [B] from the interlocks.

The hand controls will pivot in both directions when the interlock is down.

Interlock Shield

When the seat bar is raised, spring forces raise the interlocks [C].

Interlock

The hand controls will not function when the interlock is up.

Refer to SEAT BAR RESTRAINT SYSTEM Inspecting and Maintaining The Seat Bar Page 46.

MC–01950

11

873 Bobcat Loader Operation & Maintenance Manual

SEAT BAR RESTRAINT SYSTEM (ADVANCED HAND CONTROLS)

A

The seat bar restraint system has a pivoting seat bar (Item 1) [A] with arm rests.

The operator controls the use of the seat bar. The seat bar in the down position helps to keep the operator in the seat.

When the seat bar is down, and the green PRESS TO OPERATE Button is activated, the lift, tilt, and traction drive functions can be operated.

1

When the seat bar is up, the lift, tilt, and traction drive functions are deactivated.

P–13721

AVOID INJURY OR DEATH When operating the machine: • Keep the seat belt fastened snugly.

• The seat bar must be lowered.

• Keep your feet on the foot rests.

W–2179–0694

Before you leave the operator’s seat: • Lower the lift arms, put the attachment flat on the ground.

• Stop the engine.

• Engage the parking brake.

• Raise seat bar.

• Move the hand controls to the NEUTRAL POSITION to make sure that both lift and tilt functions are deactivated.

The seat bar system must deactivate the lift and tilt control functions when the seat bar is up.

Service the system if hand controls do not deactivate.

W–2302–0698

Refer to SEAT BAR RESTRAINT SYSTEM Inspecting and Maintaining The Seat Bar Page 47.

12

873 Bobcat Loader Operation & Maintenance Manual

HYDRAULIC CONTROLS

A

Foot Pedals

3

2 P–10170

1

Keep both feet on pedals while operating machine. Failure to do so can cause serious injury.

W–2002–1285 Put your feet on the pedals and KEEP THEM THERE any time you operate the loader.

Two foot pedals (Item 1) [A] control the hydraulic cylinders for the lift and tilt functions.

Lift Arm Operation

B–13559

The left pedal controls the lift arms. Push on the bottom (heel) (Item 2) [A] of the pedal to raise the lift arms.

Push on the top (toe) (Item 3) [A] of the pedal to lower the lift arms.

4

Lift Arm Float Position

5

Push the top (toe) (Item 3) [A] of the pedal all the way forward until it locks into the float position.

1 P–10170

Use the float position of the lift arms to level loose material while driving backward.

Push the bottom (heel) of the lift pedal to unlock from the float position.

Tilt Operation The right pedal controls the action of the bucket. Push the top (toe) (Item 4) [A] of the pedal to tilt the bucket forward.

Push the bottom of the pedal (heel) (Item 5) [A] to tilt the bucket backward.

Bucket Position Valve Operation (If Equipped)

B–13560

The function of the bucket position valve is to keep the bucket in the same approximate position it is placed in, before beginning the upward lift cycle.

Bucket positioning functions automatically during the upward lift cycle only.

The bucket positioning function can be turned OFF with the bucket level switch (See Page 3 & 4).

13

873 Bobcat Loader Operation & Maintenance Manual

HYDRAULIC CONTROLS (Cont’d)

A

Hand Controls

1 5

2

Keep both feet on footrests while operating machine. Failure to do so can cause serious injury.

B–15781

W–2152–0594

Put your feet on the footrests and KEEP THEM THERE for comfort and safety any time you operate the loader.

Two hand levers [A] control the hydraulic cylinders for the lift and tilt functions.

Lift Arm Operation The left hand lever controls the lift arms. Move the left hand lever away (Item 1) [A] from the operator to raise the lift arms.

B–13559

Move the left hand lever toward (Item 2) [A] the operator to lower the lift arms.

Lift Arm Float Position Move the left hand lever all the way toward the operator (Item 2) [A] until it locks into the float position.

3

Later AHC Models With Float Button – Press anbd hold the Float Button (Item 5) [A] before moving the lever.

– Press again to disengage.

4

Use the float position of the lift arms to level loose material while driving backward.

B–15781

Move the left hand lever upward to unlock from the float position.

Tilt Operation The right hand lever controls the action of the bucket.

Move the right hand lever away (Item 3) [A] from the operator to tilt the bucket forward.

Move the right hand lever toward (Item 4) [A] the operator to tilt the bucket backward.

Bucket Position Valve Operation (If Equipped) The function of the bucket positioning valve is to keep the bucket in the same approximate position it is placed in before beginning the upward lift cycle.

B–13560

B

Bucket positioning functions automatically during the upward lift cycle only.

The bucket positioning function can be turned OFF with the bucket level switch. (See Page 3 & 4.)

Advanced Hand Controls (AHC) (If Equipped) AHC operation is the same as mechanical hand controls above.

1

Two lights (Item 1) [B] on the left handle are always ON when the AHC is functioning correctly. If lights are blinking or do not come ON, see Advanced Hand Controls Troubleshooting Chart Page 77.

Left Steering Lever 14

P–13255

873 Bobcat Loader Operation & Maintenance Manual

HYDRAULIC CONTROLS (Cont’d)

A

Auxiliary Hydraulics (If Equipped)

AVOID BURNS Hydraulic fluid, tubes, fittings and quick couplers can get hot when running machine and attachments. Be careful when connecting and disconnecting quick couplers.

P–10359

W–2220–0396

NOTE: The loaders have auxiliary proportional control for front auxiliary hydraulics only.

Proportional control allows for slow–to–fast movement of auxiliary functions. EXAMPLE: If you move the auxiliary switch half way, the auxiliary function will move at approximately one–half speed.

B

Locked

1

2

Quick Couplers (Flush Face) To Connect: Remove any dirt or debris from the surface of both the male and female coupler halves, and from the outside diameter of the male coupler. Visually check the couplers for corroding, cracking, damage, or excessive wear. If any of these conditions exist, the coupler(s) must be replaced [A].

To Release 3 P–10566

Install the male half coupler into the female half coupler. Full connection is established when the ball release sleeve slides forward on the female coupler and the sleeve is rotated so that the locking pins (Item 1) [B] and the groove (Item 2) [B] do NOT align (Locked Position).

NOTE: If the locking pins and groove (Item 3) [B] are aligned, accidental disconnection is possible.

To Disconnect: Rotate the ball release sleeve so that the grooves are aligned with the pins (Item 3) [B] in the female coupler.

Holding the male coupler, retract the sleeve on the female coupler until the couplers disconnect.

NOTE: Caps and plugs are not used with flush face couplers.

15

873 Bobcat Loader Operation & Maintenance Manual

HYDRAULIC CONTROLS (Cont’d.)

A

Auxiliary Hydraulics (If Equipped) (Cont’d)

Without BOSS

Auxiliary Hydraulics Switch • Momentary Operation Press the Auxiliary Hydraulics Switch (Item 1) [A] once.

With BOSS

1

1

The light (Item 2) [A] will be ON. • Continuous Operation Press the Auxiliary Hydraulics Switch (Item 1) [A] a second time.

2

2

Both lights (Items 2 & 3) [A] will be ON.

3

3

• Disengage Press the Auxiliary Hydraulics Switch (Item 1) [A] a third time.

P–10466

TWO–SWITCH HANDLES

B

Both lights (Items 2 & 3) [A] will be OFF. NOTE: When the operator is seated and raises the seat bar, the Auxiliary Hydraulic System (Front and Rear) will deactivate. Press the Auxiliary Hydraulics Switch (Item 1) [A] to reselect operating mode.

P–10489

1

3 Left Steering Lever

FRONT Auxiliary Hydraulics Operation (RIGHT Steering Lever)

2

Right Steering Lever

• Set the Auxiliary Hydraulics Switch for Momentary Operation (See above.)

• Push the switch (Item 1) [B] or [C] to the right or left to change the fluid flow direction to the front quick couplers. (EXAMPLE: Open and close grapple teeth.)

P–02154

C

FRONT Auxiliary Hydraulics Continuous Operation (RIGHT Steering Lever)

3

P–02152

DELUXE HANDLES 1

• Set the Auxiliary Hydraulics Switch for Continuous Operation (See above).

• Push the front switch (Item 2) [B] or [C] to give the front quick couplers a constant flow of fluid (EXAMPLE: Operate a backhoe.)

• To release from continuous flow operation, press the front switch (Item 2) [B] or [C] a second time.

2

REAR Auxiliary Hydraulics Operation (LEFT Steering Lever)

Left Steering Lever

Right Steering Lever

P–13255

• Set the Auxiliary Hydraulics Switch for Momentary or Continuous Operation (See above).

D

• Push the switch (Item 3) [B] or [C] to the right or left to change the fluid flow direction to the rear quick couplers [D]. (EXAMPLE: Raise and lower rear stabilizers.)

P–13254

REAR AUXILIARY QUICK COUPLERS

NOTE: See SYSTEMS ANALYSIS Page 73 for troubleshooting malfunctions with the Auxiliary Hydraulics Operation.

P–09664

16

873 Bobcat Loader Operation & Maintenance Manual

HYDRAULIC CONTROLS (Cont’d.)

A

Attachment Functions Control (If Equipped) (Attachment Control Kit Required) (Item 1) [A] When his kit is installed, you can use other switches on the right and left control handles (Deluxe Handles) for functions such as water spray, left/right turn signals (Europe only), raise/lower the left/right ends of the moldboard on a Grader, etc.

1

The following are examples only, consult Attachment Operation & Maintenance Manual: Switch (Item 1) [B] . . . Left/Right Turn Signals Switch (Item 2) [B] . . . Left Moldboard Up/Down Switch (Item 3) [B] . . . Right Moldboard Up/Down Switch (Item 4) [B] . . . Water Spray

P–09503

B

1

DELUXE HANDLES 2

Diesel fuel or hydraulic fluid under pressure can penetrate skin or eyes, causing serious injury or death. Fluid leaks under pressure may not be visible. Use a piece or cardboard or wood to find leaks. Do not use your bare hand.

Wear safety goggles. If fluid enters skin or eyes, get immediate medical attention from a physician familiar with this injury.

Left Steering Lever

W–2072–0496

P–13255

4

3

Right Steering Lever P–13254

Relieving Hydraulic Pressure 6.

With the engine running, turn the key switch quickly to the left (counterclockwise) past the OFF POSITION. Hold key for at least five seconds after the engine comes to a complete stop. This relieves pressure that can be trapped in the front auxiliary circuit which would make it difficult to engage quick couplers from an attachment.

17

873 Bobcat Loader Operation & Maintenance Manual

DAILY INSPECTION Maintenance work must be done at regular intervals. Failure to do so will result in excessive wear and early failures. The Service Schedule [A] is a guide for correct maintenance of the Bobcat loader. It is located inside the rear door of the loader and also in the Machine Sign Translations Page 79.

A

Daily Inspection and Maintenance: • Engine Oil Level • Hydraulic/Hydrostatic Fluid Level • Engine Air Filter, Air System for Damage or Leaks • Engine Coolant Level, System for Damage or Leaks • Operator Cab, Seat Belt, Seat Bar, Pedal or Hand Control Interlocks & Mounting Hardware • Grease Pivot Pins (Lift Arms, Bob–Tach, Cylinders, Bob–Tach Wedges • Tires for Wear or Damage and Correct Air Pressure • Fuel Filter, Remove Trapped Water • Loose or Broken Parts • Safety Treads and Safety Signs (Decals) • Bobcat Interlock Control System (BICS™) • Lift Arm Support Device

6718398

NOTE: Fluids such as engine oil, hydraulic fluid, coolant, etc. must be disposed of in an environmentally safe manner.

Some regulations require that certain spills and leaks on the ground must be cleaned in a specific manner. See local, state and federal regulations for correct disposal.

GETTING READY FOR OPERATION Read and understand the Operation & Maintenance Manual and the Operator’s Handbook (Item 1) [B] before operating the loader.

Instructions are necessary before operating or servicing machine. Read and understand the Operation & Maintenance Manual, Handbook and signs (decals) on machine. Follow warnings and instructions in the manuals when making repairs, adjustments or servicing.

Check for correct function after adjustments, repairs or service. Untrained operators and failure to follow instructions can cause injury or death.

W–2003–0199

B 1 2

Operator must have instructions before running the machine. Untrained operators can cause injury or death.

W–2001–0596

P–10159

The Operation & Maintenance Manual and other manuals can be kept in a box (Item 2) [B] provided at the right hand side of the operator seat.

C

Use the bucket or attachment steps, grab handles and safety treads (on top of the loader lift arms and frame) to get on and off the loader [C].

Safety treads are installed on the Bobcat loader to provide a slip resistant surface for getting on and off the loader.

Keep safety treads clean and replace when damaged.

Replacement treads are available from your Bobcat loader dealer.

P–10435

18

873 Bobcat Loader Operation & Maintenance Manual

GETTING READY FOR OPERATION (Cont’d.)

A

Pull the seat lever (Item 1) [A] and adjust the seat position for comfortable operation of the loader controls.

1

P–10163

Fasten the seat belt snugly and adjust it so that the buckle is centered between your hips [B].

B

AVOID INJURY OR DEATH When operating the machine: • Keep the seat belt fastened snugly.

• The seat bar must be lowered.

• Keep your feet on the pedal controls or footrests.

Failure to obey warnings can cause injury or death.

W–2261–0397

P–10432

C

Lower the seat bar [C].

Be sure the parking brake is engaged.

All controls must be in the NEUTRAL POSITION before you start the engine.

After you start the engine, press the green PRESS TO OPERATE Button on the left instrument panel to operate lift, tilt and traction functions.

P–10433

D Keep your hands on the steering levers and feet on the foot pedals (or footrests) while seated in the loader [D].

P–10430

19

873 Bobcat Loader Operation & Maintenance Manual

STARTING THE ENGINE

NEUTRAL POSITION

A

Normal Starting (Without BOSS®) 8.

Put the foot pedals (or hand controls) and steering levers in NEUTRAL POSITION (center) (Item 1) [A].

1

Be sure the parking brake is engaged. Set the engine speed control to the 1/2 SPEED position (Item 2) [A].

1/2 SPEED

Turn the key switch to the ON POSITION. The engine and transmission warning lights will be ON when the key switch is on and the engine is stopped (Item 3) [A].

2

Turn the key switch to START POSITION (Item 4) [A] and release it when the engine starts.

ON POSITION

When you release the key, it will return to the RUN POSITION (Item 5) [A].

STOP THE ENGINE IF THE WARNING LIGHTS DO NOT GO OFF.

3 START POSITION

Advanced Hand Controls Only: Make sure both hand controls are in neutral before starting the engine.

Do not move the Advanced Hand Control levers from the neutral position when turning the key ON.

4

If either hand control is moved:

RUN POSITION

a. – The neutral position for the hydraulic valve spool and hand control may not be correctly calibrated. This can result in movement of the lift or tilt hydraulic cylinders when the hand control lever is returned to the neutral position after start– up.

PI–02188 MC–02033

5

OR

B

b. – The hydraulics will not operate (corresponding diagnostic lights on the left handle will blink).

If either condition occurs, turn the key OFF. Put the controls in neutral position and re–start the engine.

Cold Temperature Starting (Without BOSS®) 7. Normal Starting Page 20. Turn the key switch to the See RUN position.

1

Push the preheat switch (Item 1) [A] on the left side of the Instrument Panel.

PRESSTO OPERATE

6713715

The decal (insert) [B] on the left side of the operator cab shows the correct amount of time to hold the preheat switch.

P–16964

Follow the steps under Normal Starting and repeat the Preheat procedure until the engine starts.

Continue to hold the preheat switch after the engine starts to preheat the combustion air as follows: If the temperature is below 32°F. (0°C.), perform the following to make starting the engine easier: Do not engage the starter for longer than 15 seconds at a time. Longer use can damage the starter by overheating. Cool the starter for one minute between uses.

I–2034–0284

• Replace the engine oil with the correct type and viscosity for the anticipated starting temperature. (See Engine Lubrication System Page 55.)

• Make sure the battery is fully charged.

• Install an engine heater, available from your Bobcat loader dealer.

20

873 Bobcat Loader Operation & Maintenance Manual

STARTING THE ENGINE (Cont’d)

A

Normal Starting (With BOSS®) 9.

Put the foot pedals (or hand controls) and steering levers in NEUTRAL POSITION (center) (Item 1) [A].

Be sure the parking brake is engaged.

NEUTRAL POSITION

1 1/2 SPEED

Set the engine speed control to 1/2 SPEED position (Item 2) [A].

Turn the key switch to the ON POSITION, one beep will sound and the display symbols will be ON [B].

2

Turn the key switch to the START POSITION. (See Cold Temperature Starting. Release the key when the engine starts.

PI–02188

B

Advanced Hand Controls Only: Make sure both hand controls are in neutral before starting the engine.

Do not move the Advanced Hand Control levers from the neutral position when turning the key ON. If either hand control is moved: a. – The neutral position for the hydraulic valve spool and hand control may not be correctly calibrated. This can result in movement of the lift or tilt hydraulic cylinders when the hand control lever is returned to the neutral position after start– up.

OR b. – The hydraulics will not operate (corresponding diagnostic lights on the left handle will blink).

If either condition occurs, turn the key OFF. Put the controls in neutral position and re–start the engine.

1

Do not engage the starter for longer than 15 seconds at a time. Longer use can damage the starter by overheating. Cool the starter for one minute between uses.

MC–02320

I–2034–0284

When the key switch is turned ON, watch the alpha numeric display for Service Codes (Item 1) [B]. These codes are from the previous work shift when a WARNING may have occurred. (See SYSTEMS ANALYSIS Page 73.)

The codes may be viewed again by turning the key switch OFF and then ON again without starting the engine.

After the engine has been started, the BOSS controller will clear all codes from memory. The codes will not appear again unless the problem recurs. The alphanumeric display will again show the operating hours.

21

873 Bobcat Loader Operation & Maintenance Manual

STARTING THE ENGINE (Cont’d)

A

Cold Temperature Starting (With BOSS®) 10.

Do not use ether with glow plug (preheat) systems. Explosion can result which can cause injury or death.

W–2071–1285 See Normal Starting Page 21. Turn the key switch to the ON POSITION. The glow plug symbol (preheat) will be ON [A].

NOTE: If the display is showing SERVICE CODES, the timing of the glow plug activation may not be visible on the display. However, the glow plugs will be energized.

Characters on the display will be GLOXX (Item 1) [A] where XX will indicate the remaining time the glow plugs will be energized.

1

Turn the key switch to the START POSITION and release when the engine starts. If the engine does not start, turn the key switch to the OFF POSITION and ON again. This will start the glow plug cycle again. When the engine is running, slowly move the engine speed control forward to increase engine RPM. MC–02042

If the starting temperature is below 32°F. (0°C.), perform the following to make starting easier:

B

• Replace the engine oil with the correct type and viscosity for the anticipated starting temperature. (See ENGINE LUBRICATION SYSTEM Page 55.)

OFF POSITION

• Make sure the battery is fully charged.

• Install an engine heater, available from your Bobcat loader dealer.

PRESSTO OPERATE

NOTE: Advanced Hand Controls Only: The hand controls must be in neutral before starting the engine. If the hand controls are not in neutral, the engine will start but lift and tilt hydraulic functions will not be able to be activated. Turn the key OFF and put hand controls in neutral position. Restart the engine.

N–16961

Warming The Hydraulic/Hydrostatic System Let the engine run for a minimum of 5 minutes to warm the engine and hydrostatic transmission fluid before operating the loader. If the warning light comes ON when operating loader (cold), more warm up time is needed.

When the temperature is below –20°F. (–30°C.), hydrostatic oil must be warmed before starting. The hydrostatic system will not get enough oil at low temperatures and will be damaged. Park the machine in an area where the temperature will be above 0°F. (–18°C.) if possible.

STOPPING THE ENGINE Pull the engine speed control fully backward to decrease the engine speed. Turn the key switch to the OFF POSITION [B].

I–2007–1285

22

873 Bobcat Loader Operation & Maintenance Manual

ATTACHMENTS AND BUCKETS

A

NOTE: Warranty is void if non–approved attachments are used on the Bobcat loader.

WRONG

Never use attachments or buckets which are not approved by Bobcat Company. Buckets and attachments for safe loads of specified densities are approved for each model.

Unapproved attachments can cause injury or death.

W–2052–1285

B–06587

The dealer can identify, for each model loader, the attachments and buckets approved by Bobcat Company.

The buckets and attachments are approved for rated operating capacity and for secure fastening to the Bob–Tach.

The rated operating capacity for this loader is shown on a decal in the operator cab. (See SPECIFICATIONS Page 89.)

AVOID INJURY OR DEATH Do not exceed rated operating capacity.

Excessive load can cause tipping or loss of control.

The rated operating capacity is determined by using a standard dirt bucket, and material of normal density, such as dirt or dry gravel. If longer buckets are used and load center moves forward it reduces the rated operating capacity. If very dense material is loaded, the volume must be reduced.

W–2053–0887

B

Exceeding the rated operating capacity [A] can cause the following problems:

WEIGHT OF LOADS LBS. (KG) (Without counterweights)

1. Steering the loader may be difficult.

3. There will be a loss of stability.

4. The life of the Bobcat loader will be reduced.

Use the correct size bucket for the type and density of material being handled. For safe handling of materials and avoiding machine damage, the attachment (or bucket) should handle a full load without going over the rated operating capacity for the loader. Partial loads make steering more difficult.

1480(670)

1680(760)

2. Tires may wear faster.

15.75 (400)

Maximum load to be carried when using a pallet fork is shown in figure [B]. See your Bobcat loader dealer for more information about pallet forks and other available attachments.

24.00 (610)

CENTER OF LOAD LOCATION Inches (mm) 6712931 6712932

23

873 Bobcat Loader Operation & Maintenance Manual

ATTACHMENTS AND BUCKETS (Cont’d)

A

Installing The Bucket Or Attachment

1

The loader is equipped with the Bob–Tach system. The Bob–Tach is used for fast changing of buckets and attachments. See the Attachment Operation & Maintenance Manual to install other attachments.

Pull the Bob–Tach levers all the way up (Item 1) [A].

Enter the loader.

Fasten the seat belt, lower the seat bar, start the engine and press the green PRESS TO OPERATE Button.

N–17037

Release the parking brake.

Lower the lift arms and tilt the Bob–Tach forward.

Drive the loader forward until the top edge of the Bob–Tach is completely under the top flange of the bucket [A] (or other attachments).

Be sure the Bob–Tach levers do not hit the bucket.

Tilt the Bob–Tach backward until the cutting edge of the bucket (or other attachment) is slightly off the ground [B].

Bob–Tach levers have spring tension. Hold lever tightly and release slowly. Failure to obey warning can cause injury.

Stop the engine and exit the loader.

W–2054–1285

B

Before you leave the operator’s seat: • Lower the lift arms, put the attachment flat on the ground.

• Stop the engine.

• Engage the parking brake.

• Raise seat bar.

• (Foot Pedal Controls) Move pedals until both lock.

• (Mechanical Hand Controls) Move the hand controls until both lock.

The seat bar system must lock the lift and tilt controls in neutral when the seat bar is up.

Service the system if hand controls do not lock correctly.

N–17038

• (Advanced Hand Controls) Move the hand

controls to the NEUTRAL POSITION to make sure that both lift and tilt functions are deactivated.

The seat bar system must deactivate the lift and tilt control functions when the seat bar is up. Service the system if hand controls do not deactivate.

C 1

W–2323–0698

Push down on the Bob–Tach levers until they are fully engaged in the locked position [C].

The levers will contact the frame as shown (Item 1) [C] when locked.

N–17042 N–17041

If the levers do not engage in the locked position, see your Bobcat loader dealer for maintenance.

24

873 Bobcat Loader Operation & Maintenance Manual

ATTACHMENTS AND BUCKETS (Cont’d)

A

The wedges (Item 1) [A] must extend through the holes (Item 1) [B] in the mounting frame of the bucket (or attachment), securely fastening the bucket to the Bob–Tach. The wedge is shown extending through the hole in the bucket [A].

1

N–17043

B Bob–Tach wedges must extend through the holes in attachment. Levers must be fully down and locked. Failure to secure wedges can allow attachment to come off and cause injury or death.

W–2102–0588

1 N–17039

Removing The Bucket Or Attachment

C

Put the attachment flat on the ground and lower or close the hydraulic equipment. If the attachment is hydraulically controlled (ie: combination bucket, backhoe, etc.), stop the engine and relieve hydraulic pressure in the auxiliary circuit. (See Relieving Hydraulic Pressure, Page 17.)

Raise the seat bar, unfasten the seat belt, set the parking brake and exit the loader.

Pull the Bob–Tach levers [C] all the way up.

Disconnect the hydraulic hoses, if necessary.

Enter the loader.

N–17040

Fasten the seat belt, lower the seat bar, start the engine and press the green PRESS TO OPERATE Button.

D

Release the parking brake.

Lower the lift arms and tilt the Bob–Tach forward.

Move the loader backward, away from the bucket or attachment [D].

P–17037

25

873 Bobcat Loader Operation & Maintenance Manual

OPERATING PROCEDURE

A

When operating on a public road or highway, always follow local regulations. For example: Slow Moving Vehicle Sign or direction signals may be required.

WITH BUCKET FULL

Always warm the engine and hydrostatic system before operating the loader.

Going Up Slope

Machines warmed up with moderate engine speed and light load have longer life.

I–2015–0284

B

B–13563

WITH BUCKET FULL

Operate the loader with the engine at full speed for maximum horsepower. Move the steering levers only a small amount to operate the loader slowly.

New operators must operate the loader in an open area without bystanders. Operate the controls until the loader can be handled at an efficient and safe rate for all conditions of the work area.

With a full bucket, go up or down the slope with the heavy end toward the top of the slope [A] & [B].

With empty bucket, go down or up the slope with the heavy end toward the top of the slope [C] & [D].

Going Down Slope

C

B–13563

WITH BUCKET EMPTY

• Keep the lift arms as low as possible.

• Do not travel or turn with the lift arms up.

• Turn on level ground.

• Go up and down slopes, not across them.

• Keep the heavy end of the machine uphill.

• Do not overload the machine.

Failure to obey warnings can cause the machine to tip or roll over and cause injury or death.

Going Down Slope

B–13564

W–2018–1187

D

WITH BUCKET EMPTY

Raise the bucket only high enough to avoid obstructions on rough ground.

Going Up Slope 26

B–13565

873 Bobcat Loader Operation & Maintenance Manual

OPERATING PROCEDURES (FOOT PEDALS)

A

Filling The Bucket Push down on the top of the lift pedal until the lift arms are all the way down.

B–12830

Push the top of the tilt pedal to put the cutting edge of the bucket on the ground [A].

B–13566

Drive slowly forward into the material.

Push the bottom of the tilt pedal to raise the front of the bucket [B].

B B–12830

Load, unload and turn on flat level ground. Do not exceed rated operating capacity shown on sign (decal) in cab. Failure to obey warnings can cause the machine to tip or roll over and cause injury or death.

W–2056–1187

Drive backward away from the material.

Emptying The Bucket Push down on the bottom of the lift pedal to raise the lift arms. Push the top of the tilt pedal while raising the lift arms to level the bucket or attachment and help prevent material from falling off the back of the bucket or attachment.

B–13567

C

Drive forward slowly until the bucket is over the top of the truck box or bin.

Push the top of the tilt pedal until the bucket is empty [C].

B–12830

If all the material is near the side of the truck or bin, push it to the other side with the bucket.

Never dump over an obstruction, such as a post, that can enter the operator cab. The machine could tip forward and cause injury or death.

W–2057–0694 B–13568

27

873 Bobcat Loader Operation & Maintenance Manual

OPERATING PROCEDURES (FOOT PEDALS) (Cont’d)

A

Digging Into The Ground Put the lift arms all the way down.

B–12830

Push the top of the tilt pedal until the cutting edge of the bucket is on the ground.

Drive forward slowly and continue to tilt the bucket down until it enters the ground [A].

Push the bottom of the tilt pedal a small amount to increase traction and keep an even digging depth.

Continue to drive forward until the bucket is full.

When the ground is hard, raise and lower the cutting edge of the bucket with the tilt pedal while driving forward slowly.

B–13569

B

Push the bottom of the tilt pedal to tilt the bucket backward as far as it will go when the bucket is full [B].

B–12830

Leveling The Ground (Using Lift Arms In Float Position) Push the top (toe) of the lift pedal all the way forward until the pedal is in the locked position to put the lift arms in a float position [C].

B–13570

Push the tilt pedal to change the position of the cutting edge on the bucket.

C

With the bucket tilted farther forward, there is more force on the cutting edge and more loose material can be moved.

B–12830

Never drive forward when the hydraulic control for lift arms is in float position.

I–2005–1285

Drive backward to level loose material.

Push the bottom (heel) of the lift pedal to unlock from the float position.

B–13571

28

873 Bobcat Loader Operation & Maintenance Manual

OPERATING PROCEDURES (FOOT PEDALS) (Cont’d)

A

Backfilling Lower the lift arms and put the cutting edge of the bucket on the ground. Drive forward to the edge of the hole to push the material into the hole [A].

B–12830

Tilt the bucket forward as soon as it is past the edge of the hole [A].

If necessary, raise the lift arms to empty the bucket.

PARKING THE BOBCAT LOADER Stop the Bobcat loader on level ground.

Lower the lift arms fully and put the attachment flat on the ground.

Pull the engine speed control lever all the way backward.

Turn the key switch to the OFF POSITION.

B–13572

AVOID INJURY OR DEATH Before you leave the operator’s seat: • Lower the lift arms, put the attachment flat on the ground.

• Stop the engine.

• Engage the parking brake.

• Raise seat bar, move pedals until both lock.

W–2045–1086

Engage the parking brake.

Lift the seat bar and make sure the foot pedals are in the locked position.

Unbuckle the seat belt.

Remove the key from the switch to prevent operation of the loader by unauthorized personnel.

29

873 Bobcat Loader Operation & Maintenance Manual

OPERATING PROCEDURE (HAND CONTROLS)

A

Filling The Bucket Move the left hand lever toward the operator until the lift arms are all the way down. Move the right hand away from the operator to put the cutting edge of the bucket on the ground [A].

B–15781

B–13566

B

Drive slowly forward into the material. Move the right hand lever toward the operator to raise the front of the bucket [B].

B–15781

Load, unload and turn on flat level ground. Do not exceed rated operating capacity shown on sign (decal) in cab. Failure to obey warnings can cause the machine to tip or roll over and cause injury or death.

W–2056–1187

Drive backward away from the material.

Emptying The Bucket

B–13567

Move the left hand lever away from the operator to raise the lift arms. Move the right hand lever away from the operator to level the bucket or attachment and help prevent material from falling off the back of the bucket or attachment.

C

Drive forward slowly until the bucket is over the top of the truck box or bin. Move the right hand lever away from the operator until the bucket is empty [C]. If all the material is near the side of the truck or bin, push it to the other side with the bucket.

B–15781

Never dump over an obstruction, such as a post, that can enter the operator cab. The machine could tip forward and cause injury or death.

W–2057–0694

B–13568

30

873 Bobcat Loader Operation & Maintenance Manual

OPERATING PROCEDURE (HAND CONTROLS) (Cont’d)

A

Digging Into The Ground Put the lift arms all the way down. Move the right hand lever away from the operator until the cutting edge of the bucket is on the ground. Drive forward slowly and continue to tilt the bucket down until it enters the ground [A].

Move the right hand lever toward the operator a small amount to increase traction and keep an even digging depth. Continue to drive forward until the bucket is full.

When the ground is hard, raise and lower the cutting edge of the bucket with the hand lever while driving forward slowly.

B–15781

B–13569

B

Move the right hand lever toward the operator to tilt the bucket backwards as far as it will go when the bucket is full [B].

B–15781

Leveling The Ground (Using Lift Arms In Float Position) Move the left hand lever all the way down and in until the hand lever is in the locked position to put the lift arms in a float position [C].

B–13570

Later AHC Models With Float Button – Press anbd hold the Float Button (Item 1) [C] before moving the lever.

– Press again to disengage.

C

Move the right hand lever to change the position of the cutting edge on the bucket. With the bucket tilted farther forward, there is more force on the cutting edge and more loose material can be moved.

1

B–15781

Never drive forward when the hydraulic control for lift arms is in float position.

I–2005–1285

Drive backward to level loose material. Move the left hand lever upward to unlock from the float position.

B–13571

31

873 Bobcat Loader Operation & Maintenance Manual

OPERATING PROCEDURE (HAND CONTROLS) (Cont’d)

A

Backfilling Lower the lift arms and put the cutting edge of the bucket on the ground. Drive forward to the edge of the hole to push the material into the hole [A].

Tilt the bucket forward as soon as it is past the edge of the hole [A]. If necessary, raise the lift arms to empty the bucket.

B–15781

PARKING THE BOBCAT LOADER Stop the Bobcat loader on level ground.

Lower the lift arms fully and put the edge of the bucket on the ground.

Pull the engine speed control all the way backward. Turn the key switch to the OFF POSITION.

B–12877

AVOID INJURY OR DEATH When operating the machine: • Keep the seat belt fastened snugly.

• The seat bar must be lowered.

• Keep your feet on the foot rests.

W–2179–0694

Before you leave the operator’s seat: • Lower the lift arms, put the attachment flat on the ground.

• Stop the engine.

• Engage the parking brake.

• Raise seat bar.

• (Mechanical Hand Controls) Move the hand controls until both lock.

The seat bar system must lock the lift and tilt controls in neutral when the seat bar is up.

Service the system if hand controls do not lock correctly.

• (Advanced Hand Controls) Move the hand

controls to the NEUTRAL POSITION to make sure that both lift and tilt functions are deactivated.

The seat bar system must deactivate the lift and tilt control functions when the seat bar is up. Service the system if hand controls do not deactivate.

W–2302–0698

Engage the parking brake.

Lift the seat bar and make sure the hand controls are in the locked position (Mechanical Only).

Unbuckle the seat belt. Remove the key from the switch to prevent operation of the loader by unauthorized personnel.

32

873 Bobcat Loader Operation & Maintenance Manual

TRANSPORTING THE BOBCAT LOADER

A

Adequately designed ramps of sufficient strength are needed to support the weight of the machine when loading onto a transport vehicle. Wood ramps can break and cause personal injury.

W–2058–0494

SUPPORT P–10446

A loader with an empty bucket or no attachment must be loaded backward onto the transport vehicle [A].

The rear of the trailer must be blocked or supported [A] when loading or unloading the loader to prevent the front end of the trailer from raising up.

Be sure the transport and towing vehicles are of adequate size and capacity.

B Both Sides

Use the following procedure to fasten the Bobcat loader to the transport vehicle to prevent the loader from moving during sudden stops or when going up or down slopes [B].

Lower the bucket or attachment to the floor. Stop the engine. Engage the parking brake. Install chains at the front and rear loader tie down positions (Inset) [B]. Fasten each end of the chain to the transport vehicle and tighten the chain with a chain tightener.

The Inset [B] shows the decal with attachment points for towing and tie down.

Both Sides P–10440

P–10448

TOWING THE LOADER To prevent damage to the loaders hydrostatic system, the loader must be towed only a short distance at slow speed.

(Example: Moving the loader onto a transport vehicle).

The towing chain (or cable) must be rated at 1–1/2 times the weight of the loader. (See SPECIFICATIONS Page 89.)

• Turn the key switch to ON and press the Traction Lock Override button. This will not work unless the engine is running because of the RPM sesnor.

• Tow the Bobcat loader at 2 MPH (3,2 km/hr) or less for not more than 25 feet (7,6 meters).

If the electrical system is not functioning, contact your Bobcat loader dealer. (Part of the brake system must be disassembled to move the loader.)

6595014

P–10447

Do not push or pull the machine at more than 2 MPH (3,2 km/h) or for a distance of more than 25 feet (7,6 meters) with the towing tool in place.

I–2017–0389

33

873 Bobcat Loader Operation & Maintenance Manual

LIFTING THE LOADER

A

873Operation&MaintenanceManual(S/N514123810&Above)#6900791–OperatingInstructionsSection

Four Point Lift

AVOID INJURY OR DEATH • Before lifting, check fasteners on four point lift.

• Never allow riders in the cab or bystanders within 15 feet (5 meters) while lifting the machine.

MC–02262

W–2160–0694

The loader can be lifted with the four point lift which is available as a kit from your Bobcat loader dealer.

Attach cables or chains to lift eyes as shown [A].

34

873 Bobcat Loader Operation & Maintenance Manual

PREVENTIVE MAINTENANCE AIR CLEANER SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 ALTERNATOR BELT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 Adjusting The Alternator Belt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 BOBCAT INTERLOCK CONTROL SYSTEM (BICS™) . . . . . . . . . . . . . . . . . 47 Additional Inspection For Loaders With AHC . . . . . . . . . . . . . . . . . . . . . . . . . 47 Inspecting The BICS™ System Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Inspecting Deactivation Of The Auxiliary Hydraulics System . . . . . . . . . . . 47 Inspecting The Lift Arm By–Pass Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Inspecting The Seat Bar Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Inspecting The Traction Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 BOB–TACH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 Inspection And Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 DRIVE BELT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 Adjusting The Drive Belt Idler Arm Stop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 Replacing The Drive Belt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

PREVENTIVE MAINTENANCE

ELECTRICAL SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 Electrical System Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 Fuse Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 Removing And Installing The Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 Using A Booster Battery (Jump Starting) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 ENGINE COOLING SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 Cleaning The Cooling System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 ENGINE LUBRICATION SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Checking Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Oil Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Replacing The Oil And Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 FAN GEARBOX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 Checking And Maintaining . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 FINAL DRIVE TRANSMISSION (CHAINCASE) . . . . . . . . . . . . . . . . . . . . . . . 65 Checking And Adding Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 Removing Oil From The Chaincase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 FUEL SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Filling The Fuel Tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Fuel Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Fuel Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Removing Air From The Fuel System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 HYDRAULIC/HYDROSTATIC SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 Checking And Adding Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 Replacing Hydraulic Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 Replacing Hydraulic/Hydrostatic Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Continued On Next Page 35

873 Bobcat Loader Operation & Maintenance Manual

PREVENTIVE MAINTENANCE (Cont’d) LIFT ARM SUPPORT DEVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Installing The Lift Arm Support Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Removing The Lift Arm Support Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 LUBRICATING THE BOBCAT LOADER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 OPERATOR CAB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Emergency Exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Lowering The Operator Cab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Raising The Operator Cab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 REAR DOOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Adjusting The Rear Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Opening The Rear Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 REAR GRILL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 SEAT BAR RESTRAINT SYSTEM (ADVANCED HAND CONTROLS) . . . . 46 Inspecting The Seat Bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Maintaining The Seat Bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 SEAT BAR RESTRAINT SYSTEM (FOOT PEDALS) . . . . . . . . . . . . . . . . . . . 44 Inspecting The Seat Bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Maintaining The Seat Bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 SEAT BAR RESTRAINT SYSTEM (MECHANICAL HAND CONTROLS) . . 45 Inspecting The Seat Bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Maintaining The Seat Bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 SERVICE SCHEDULE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 TIMING BELT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 TIRE MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 Tire Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 Tire Rotation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 Wheel Nuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 TRACTION LOCK CONTROL SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Inspecting The Traction Lock Control System . . . . . . . . . . . . . . . . . . . . . . . . 48 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

36

873 Bobcat Loader Operation & Maintenance Manual

MAINTENANCE SAFETY Instructions are necessary before operating or servicing machine. Read and understand the Operation & Maintenance Manual, Handbook and signs (decals) on machine. Follow warnings and instructions in the manuals when making repairs, adjustments or servicing. Check for correct function after adjustments, repairs or service. Untrained operators and failure to follow instructions can cause injury or death.

W–2003–0199

Safety Alert Symbol: This symbol with a warning statement, means: “Warning, be alert! Your safety is involved!” Carefully read the message that follows.

CORRECT

CORRECT

CORRECT

B–10731

B–13573

B–13561

Never service the Bobcat® Skid Steer Loader without instructions.

Use the correct procedure to lift or lower operator cab.

Cleaning and maintenance are required daily.

WRONG

WRONG

WRONG

B–13574

B–15232

B–15281

Have good ventilation when welding or grinding painted parts.

Wear dust mask when grinding painted parts. Toxic dust and gas can be produced.

Avoid exhaust fume leaks which can kill without warning. Exhaust system must be tightly sealed.

Disconnecting or loosening any hydraulic tubeline, hose, fitting, component or a part failure can cause lift arms to drop. Do not go under lift arms when raised unless supported by an approved lift arm support device. Replace if damaged.

Never work on loader with lift arms up unless lift arms are held by an approved lift arm support device. Replace if damaged.

Never modify equipment or add attachments not approved by Bobcat Company.

WRONG

WRONG

WRONG

B–13576

B–13577

B–6589

Stop, cool and clean engine of flammable materials before checking fluids.

Never service or adjust loader with the engine running unless instructed to do so in the manual.

Avoid contact with leaking hydraulic fluid or diesel fuel under pressure. It can penetrate the skin or eyes.

Never fill fuel tank with engine running, while smoking or when near open flame.

Keep body, jewelry and clothing away from moving parts, electrical contacts, hot parts and exhaust.

Wear eye protection to guard from battery acid, compressed springs, fluids under pressure and flying debris when engines are running or tools are used. Use eye protection approved for type of welding.

Keep rear door closed except for service. Close and latch door before operating the loader.

Lead–acid batteries produce flammable and explosive gases.

Keep arcs, sparks, flames and lighted tobacco away from batteries.

Batteries contain acid which burns eyes or skin on contact.

Wear protective clothing. If acid contacts body, flush well with water. For eye contact flush well and get immediate medical attention.

Maintenance procedures which are given in the Operation & Maintenance Manual can be performed by the owner/operator without any specific technical training. Maintenance procedures which are not in the Operation & Maintenance Manual must be performed ONLY BY QUALIFIED BOBCAT SERVICE PERSONNEL. Always use genuine Bobcat replacement parts. The Service Safety Training Course is available from your Bobcat dealer.

37

MSW03–0600

873 Bobcat Loader Operation & Maintenance Manual

38

873 Bobcat Loader Operation & Maintenance Manual

SERVICE SCHEDULE Maintenance work must be done at regular intervals. Failure to do so will result in excessive wear and early failures. The 5. service schedule is a guide for correct maintenance of the Bobcat loader.

Instructions are necessary before operating or servicing machine.

Read and understand the Operation & Maintenance Manual, Handbook and signs (decals) on machine. Follow warnings and instructions in the manuals when making repairs, adjustments or servicing. Check for correct function after adjustments, repairs or service. Untrained operators and failure to follow instructions can cause injury or death.

W–2003–0199

ITEM Engine Oil Engine Air Cleaner Engine Cooling System Lift Arms, Cyl., Bob–Tach Pivot Pins and Wedges Engine Air System Tires Seat Belt, Seat Bar & Pedal Interlocks or Hand Control Interlocks Bobcat Interlock Control System (BICSTM) Safety Signs and Safety Treads Operator Cab Fuel Filter Traction Lock Control Sys. Hyd. Fluid, Hoses and Tubelines Final Drive Trans.(Chaincase) Battery Foot Pedals or Hand Controls and Steering Wheel Nuts

SERVICE REQUIRED

8–10

50

◊

250 500 1000 3000

Check the oil level and add oil as needed.

Check condition indicator or display panel. Service only when required.

Clean debris from oil cooler radiator & grill.

Lubricate with multi–purpose lithium based grease (12 places).

Check for leaks and damaged components.

Check for damaged tires and correct air pressure.

Check the condition of seat belt. Check the seat bar and foot pedal interlocks or hand control interlocks for correct operation.

Clean dirt and debris from moving parts.

Check BICS™ functions.

Check for damaged signs (decals) and safety treads. Replace any signs or safety treads that are damaged or worn.

Check the fastening bolts, washers and nuts. Check the condition of the cab.

Remove the trapped water.

Check operation and correct as needed.

Check fluid level & add as needed. Check for damage & leaks.

Repair or replace as needed.

Check oil level.

Check cables, connections and electrolyte level. Add distilled water as needed.

Check for correct operation. Repair or adjust as needed.

Check for loose wheel nuts and tighten to 105–115 ft.–lbs.

(142–156 Nm) torque.

Parking Brake Check operation of the brake.

Alternator Belt Check tension and adjust as needed.

Engine/Hydro. Drive Belt * Check for wear or damage. Check idler arm stop.

Fuel Filter Replace filter element.

Steering Shaft Grease three fittings.

Hyd. Res. Breather Cap Replace the reservoir breather cap.

Hyd./ Hydro. Filter Replace the filter element.

Engine Oil and Filter Replace oil and filter. Use CD or better grade oil and Bobcat filter.

Final Drive Trans.(Chaincase) Replace the oil in the chaincase.

Hydraulic Reservoir Clean or replace the fluid.

Case Drain Filters Clean or replace the case drain filters.

Bobcat Interlock Control Check lift arm by–pass control.

System (BICSTM) Fan Drive Gearbox Check gear lube level. ∞ Adjust the engine valves.

Engine Valves Engine Timing Belt ◊ Replace the timing belt and belt tensioner assy.

* ∞ ◊

Check wheel nut torque every 8 hours for the first 24 hours.

Inspect the new belt after first 50 hours.

Also replace hydraulic/hydrostatic filter element when the transmission warning light comes ON. After the first 50 hours.

After the first 500 hours on new engine, adjust engine valves; 1000 hours thereafter. (See Service Manual for procedure.)

Or every 12 months.

Or every 5 years.

873 Bobcat Loader Operation & Maintenance Manual 39

LIFT ARM SUPPORT DEVICE 6.

A 1 1

P–09559

B

Never work on a machine with the lift arms up unless the lift arms are secured by an approved lift arm support device. Failure to use an approved lift arm support device can allow the lift arms or attachment to fall and cause injury or death.

W–2059–0598

1

Service lift arm support device if damaged or if parts are missing. Using a damaged lift arm support or with missing parts can cause lift arms to drop causing injury or death.

W–2271–1197

P–04641

Installing The Lift Arm Support Device Put jackstands under the rear corners of the loader frame.

C

Remove the retainer knobs (Item 1) [A] or [B].

Remove the lift crossmember.

arm

support

device

from

the

One person must stay in the operator seat [C] with the seat belt fastened and the seat bar lowered, while second person installs the lift arm support device.

P–10136

Start the engine, press the green PRESS TO OPERATE Button and raise the lift arms.

Have a second person install the lift arm support device over the rod of one of the lift cylinders [C].

P–10130

The 90° notch should be installed against the outer case of the lift cylinder [C]. (See Inset.)

D

Lower the lift arms slowly until the support device is held between the lift arms and lift cylinder [D].

Removing The Lift Arm Support Device Raise the lift arms while a second person removes the lift arm support device [C].

Stay in the seat until the lift arms are lowered all the way.

Return the lift arm support device to the storage position and secure the retainer knobs (Item 1) [A] or [B].

P–10132

40

873 Bobcat Loader Operation & Maintenance Manual

OPERATOR CAB

A

P–10134

The Bobcat loader has an operator cab (ROPS and FOPS) as standard equipment to protect the operator from rollover and falling objects [A]. Check with your dealer if the operator cab has been damaged.

Use care when raising or lowering the operator cab to prevent damaging the shaft of the lift arm by–pass control.

ROPS/FOPS – Roll Over Protective Structure per SAE J1040 and ISO 3471, and Falling Object Protective Structure per SAE J1043 and ISO 3449, Level l. Level ll is available.

I–2070–0596

Level l – Protection from falling bricks, small concrete blocks and hand tools encountered in operations such as highway maintenance, landscaping, and other construction site services.

Level ll – Protection from falling trees, rocks; for machines involved in site clearing, overhead demolition or forestry.

Never modify operator cab by welding, grinding, drilling holes or adding attachments unless instructed to do so by Bobcat Company.

Changes to the cab can cause loss of operator protection from rollover and falling objects, and result in injury or death.

W–2069–1285

Before the cab or the lift arms are raised for service, jackstands must be put under the rear corners of the frame. Failure to use jackstands can allow the machine to tip backward causing injury or death.

W–2014–0895

41

873 Bobcat Loader Operation & Maintenance Manual

OPERATOR CAB

A

Raising The Operator Cab 7.

Always stop the engine before raising or lowering the cab.

P–10449

Stop the loader on a level surface. Lower the lift arms.

Stop the engine. If the lift arms must be up while raising the operator cab, install the lift arm support device. (See LIFT ARM SUPPORT DEVICE Page 40.)

P–10134

B

Put jackstands under the rear of the loader frame (Inset) [A].

Mechanical Hand Controls Only: Disconnect the control linkage joint from the bottom hole (work position) and move to the TOP hole on the control handle (both sides) [B]. Both control handles must be in the vertical position so there will be no cab interference with the steering levers when the operator cab is raised or lowered.

Advanced Hand Controls Only: Hold the steering levers forward so that the cab does not hit the levers when raising the cab.

Loosen the nut (both sides) at the front corner of the operator cab [C].

P–03470

Remove the nut and plate (both sides) [C].

C

Lift on the grab handle and bottom of the operator cab slowly until the cab latching mechanism engages and the cab is all the way up [A].

P–10086

P–10084

Use care when raising or lowering the operator cab to prevent damaging the shaft of the lift arm by–pass control.

I–2070–0596

42

873 Bobcat Loader Operation & Maintenance Manual

OPERATOR CAB (Cont’d)

A

Lowering The Operator Cab NOTE: Make sure the seat bar is fully raised or lowered when lowering the cab. Always use the grab handles to lower the cab.

Advanced Hand Controls Only: Hold the steering levers forward so that the cab does not hit the levers when lowering the cab.

P–10138

Pull down on the bottom of the operator cab until it stops at the latching mechanism.

Release the latching mechanism and pull the cab all the way down [A].

P–10360

Install the plate and nut (both sides) [B].

B

Tighten the nuts to 40–50 ft.–lbs. (54–68 Nm) torque.

Use care when raising or lowering the operator cab to prevent damaging the shaft of the lift arm by–pass control.

I–2070–0596

P–10084

Mechanical Hand Controls Only: Move the control linkage from the top hole to the BOTTOM hole (work position) on the control handle (both sides) [C].

P–10086

C

P–03561

43

873 Bobcat Loader Operation & Maintenance Manual

OPERATOR CAB (Cont’d)

A

Emergency Exit The front opening on the operator cab and rear window provide exits.

Rear Window: Pull on the tag on the top of the rear window to remove the rubber cord [A].

P–10168

B

Push the rear window out of the rear of the operator cab.

Exit through the rear of the operator cab [B].

P–10434

C

Front Door: (If Equipped) NOTE: When an Operator Cab Enclosure Kit is installed, the window of the front door can be used as an emergency exit. [C] Pull the plastic loop at the top of the window in the front door to remove the rubber cord [C].

P–09216

D

Push the window out with your foot [D].

Exit through the front door.

P–09217

44

873 Bobcat Loader Operation & Maintenance Manual

SEAT BAR RESTRAINT SYSTEM (FOOT PEDALS)

A

The seat bar restraint system has a pivoting, spring assist seat bar with arm rests and has spring loaded interlocks for the lift and tilt control functions.

Clean (Both Sides)

The operator controls the use of the seat bar. The seat bar in the down position helps to keep the operator in the seat.

The interlocks require the operator to lower the seat bar in order to operate the foot pedal controls.

When the seat bar is up, the lift and tilt control functions are locked when returned to the neutral position.

P–10361

AVOID INJURY OR DEATH The Seat Bar System must lock the lift and tilt foot pedals or hand controls in neutral when the Seat Bar is up. Service the system if controls do not lock correctly.

AVOID INJURY OR DEATH Never operate loader without interlock shield 6705474 on both interlocks. Shields prevent foot from unlocking interlocks when leaving loader seat.

W–2263–0597

W–2158–0594

Inspecting The Seat Bar Sit in the seat and fasten the seat belt. Engage the parking brake. Pull the seat bar all the way down. Start the engine. Press the green PRESS TO OPERATE Button.

Operate each foot pedal to check both the lift and tilt functions. Raise the lift arms until the bucket is about 2 feet (600 mm) off the ground.

B

Raise the seat bar. Try to move each foot pedal. Pedals must be firmly locked in neutral position. There must be no motion of the lift arms or tilt (bucket) when the pedals are pushed.

Clean

Pull the seat bar down, press the green PRESS TO OPERATE Button and lower the lift arms. Operate the lift pedal. While the lift arms are going up, raise the seat bar and the lift arms should stop.

Lower the seat bar, Press the green PRESS TO OPERATE Button, lower the lift arms and put the bucket flat on the ground. Stop the engine. Raise the seat bar and operate the foot pedals to be sure that the pedals are firmly locked in the neutral position. Unbuckle the seat belt.

Maintaining The Seat Bar 8.

See the SERVICE SCHEDULE Page 39 and on the loader for correct service interval.

Interlock Shield

Clean any debris or dirt from the moving parts [A] & [B].

Inspect the linkage bolts and nuts for tightness. The correct torque is 25–28 ft.–lbs. (34–38 Nm).

If the seat bar system does not function correctly, check for free movement of each linkage part. Check for excessive wear. Adjust pedal control linkage. Replace parts that are worn or damaged. Use only genuine Bobcat loader replacement parts.

P–10108

45

873 Bobcat Loader Operation & Maintenance Manual

SEAT BAR RESTRAINT SYSTEM (MECHANICAL HAND CONTROLS) 9.

The seat bar restraint system has a pivoting, spring assist seat bar with arm rests and has spring loaded interlocks for the lift and tilt control functions.

A Clean (Both Sides)

The operator controls the use of the seat bar. The seat bar in the down position helps to keep the operator in the seat.

The interlocks require the operator to lower the seat bar in order to operate the hand controls.

When the seat bar is up, the lift and tilt control functions are locked when returned to the neutral position.

P–10361

AVOID INJURY OR DEATH The Seat Bar System must lock the lift and tilt foot pedals or hand controls in neutral when the Seat Bar is up. Service the system if controls do not lock correctly.

AVOID INJURY OR DEATH Never operate loader without interlock shield 6705474 on both interlocks. Shields prevent foot from unlocking interlocks when leaving loader seat.

W–2263–0597

W–2158–0594

Inspecting The Seat Bar Sit in the seat and fasten the seat belt. Engage the parking brake. Pull the seat bar all the way down. Press the green PRESS TO OPERATE Button. Start the engine. Operate each hand control to check both the lift and tilt functions. Raise the lift arms until the bucket is about 2 feet (600 mm) off the ground.

B

Raise the seat bar. Try to move each hand control. The controls must be firmly locked in neutral position. There must be no motion of the lift arms or tilt (bucket) when the controls are pushed.

Clean

Pull the seat bar down, press the green PRESS TO OPERATE Button and lower the lift arms. Operate the lift control. While the lift arms are going up, raise the seat bar and the lift arms should stop.

Lower the seat bar, lower the lift arms, press the green PRESS TO OPERATE Button and put the bucket flat on the ground. Stop the engine. Raise the seat bar and operate the hand controls to be sure that the controls are firmly locked in the neutral position. Unbuckle the seat belt.

Maintaining The Seat Bar See the SERVICE SCHEDULE Page 39 for correct service interval.

Interlock Shield

Clean any debris or dirt from the moving parts [A] & [B].

Inspect the linkage bolts and nuts for tightness. The correct torque is 25–28 ft.–lbs. (34–38 Nm).

If the seat bar system does not function correctly, check for free movement of each linkage part. Check for excessive wear. Adjust hand control linkage. Replace parts that are worn or damaged. Use only genuine Bobcat loader replacement parts.

P–09671

46

873 Bobcat Loader Operation & Maintenance Manual

SEAT BAR RESTRAINT SYSTEM (ADVANCED HAND CONTROLS) 10.

A

The seat bar restraint system has a pivoting seat bar (Item 1) [A] with arm rests.

1

The operator controls the use of the seat bar. The seat bar in the down position helps to keep the operator in the seat.

When the seat bar is down and the green PRESS TO OPERATE Button is activated, the lift, tilt, and traction drive functions can be operated.

P–13721

When the seat bar is up, the lift, tilt, and traction drive functions are deactivated.

B

Inspecting The Seat Bar Sit in the operator’s seat. Turn the key ON, lower the seat bar and press the green PRESS TO OPERATE Button.

Both lights on the left handle should be ON.

Clean (Both Sides)

Move each hand control back and forth. You should hear the zip,zip sound of the lift and tilt actuators moving the control valve spools (under the seat).

Raise the seat bar fully. Both lights on the left handle should be OFF. Move each hand control back and forth. There must be no zip–zip sound of the lift or tilt actuators. If either actuator makes a sound while the seat bar is raised, contact your dealer for service.

P–10361

Maintaining The Seat Bar See the SERVICE SCHEDULE Page 39 for correct service interval.

Clean any debris or dirt from the moving parts [B].

AVOID INJURY OR DEATH

If the seat bar system does not function correctly replace parts that are worn or damaged. Use only genuine Bobcat replacement parts.

When operating the machine: • Keep the seat belt fastened snugly.

• The seat bar must be lowered.

• Keep your feet on the foot rests.

W–2179–0694

Before you leave the operator’s seat: • Lower the lift arms, put the attachment flat on the ground.

• Stop the engine.

• Engage the parking brake.

• Raise seat bar.

• (Advanced Hand Controls) Move the hand controls to the NEUTRAL POSITION to make sure that both lift and tilt functions are deactivated.

The seat bar system must deactivate the lift and tilt control functions when the seat bar is up. Service the system if hand controls do not deactivate.

W–2321–0698

47

873 Bobcat Loader Operation & Maintenance Manual

BOBCAT INTERLOCK CONTROL SYSTEM (BICS™) 11.a Inspecting The BICS™ Controller (Engine STOPPED – Key ON) 13.1. Sit in the operator’s seat. Turn key ON, lower the seat bar and disengage the parking brake. Press the green PRESS TO OPERATE Button. Four (4) BICS controller lights should be ON (Items 1, 2, 3, & 5) [A].

2. Engage the parking brake and raise the seat bar fully. System Activated (Item 1) [A], seat bar light (Item 2) [A], valve light (Item 3) [A] and traction light (Item 4) [A] should be OFF. NOTE: If lights on BICS Controller are blinking, see BICS Troubleshooting Chart, Page 77.)

A

1 2 3 4 5

3. Exit the loader and press traction lock override button. Traction light (Item 4) [A] should be ON. Press override button again and traction light (Item 4) [A] should be OFF.

N–17979

Deactivation Of The Auxiliary Hydraulics System (Engine STOPPED – Key ON) 14.a 4. Sit in the operator’s seat. Lower the Seat Bar. Press the green PRESS TO OPERATE Button. Press the auxiliary hydraulics switch. The auxiliary switch light will come ON. Raise the Seat Bar. The light should be OFF. Inspecting The Seat Bar Sensor (Engine RUNNING) 5. Sit in the operator’s seat. Lower the seat bar. Press the green PRESS TO OPERATE button. Engage the parking brake. Fasten the seat belt.

AVOID INJURY OR DEATH The Bobcat Interlock Control System (BICS™) must deactivate the lift, tilt and traction drive functions. If it does not, contact your dealer for service. DO NOT modify the system.

W–2151–0394

6. Start the engine and operate at low idle. While raising the lift arms, raise the seat bar fully. The lift arms should stop. Repeat using the tilt function.

Inspecting The Traction Lock (Engine RUNNING) 12.

7. Fasten the seat belt, disengage the parking brake, and raise the seat bar fully. Move the steering levers slowly forward and backward. The traction lock should be engaged. Lower the seat bar.

8. Engage the parking brake pedal and move the steering levers slowly forward and backward. The traction lock should be engaged.

Inspecting The Lift Arm By–Pass Control 9. Raise the lift arms 6 feet (2 m) off the ground. Stop the engine. Turn the Lift Arm By–Pass Control Knob clockwise 1/4 turn. Then pull up and hold the Lift Arm By–Pass Control Knob until the lift arms slowly lower.

Additional Inspection For Loaders With Advanced Hand Controls 10. Sit in the operator’s seat and fasten the Seat Belt.

Lower the Seat Bar, start the engine and press the green PRESS TO OPERATE Button.

11. Start the engine and raise the lift arms about 3 feet (1 meter) off the ground.

12. Turn the key OFF and wait for the engine to come to a complete stop.

13. Turn the key ON. Move the left hand control toward the operator. The lift arms should not lower.

14. With the key on and bucket installed, move the right hand control away from the operator. The bucket should not tip forward.

48

873 Bobcat Loader Operation & Maintenance Manual

TRACTION LOCK CONTROL SYSTEM

A

Inspecting The Traction Lock Control System

1 2

1. Sit in the operator’s seat. Turn the key ON, lower the seat bar. Press the green PRESS TO OPERATE Button, and disengage the parking brake. Four (4) of the BICS Controller lights should be ON (Items 1,2,3, and 5) [A]. The Traction light (Item 4) [A] should be OFF.

3 4 5

2. Fasten the Seat Belt, engage the parking brake, start the engine and press the PRESS TO OPERATE Button. Disengage the parking brake and operate at low idle. The Traction light (Item 4) [A] should be ON.

N–17979

Maintenance

B

Check the wire connections at the engine speed sensor (Item 1) [B].

NOTE: When the Traction Lock Override Button is activated, the Traction Lock Override Control System will NOT engage the Traction Lock if the engine stops.

1

P–09440

49

873 Bobcat Loader Operation & Maintenance Manual

REAR DOOR

A

Opening And Closing The Rear Door

1

AVOID INJURY OR DEATH Never service or adjust the machine when the engine is running unless instructed to do so in the manual.

P–10350

W–2012–0497

Put your fingers into the slot in the rear door and pull on the latch handle [A].

Pull the rear door open.

Push the door stop up into the hinge (Item 1) [A], then close the rear door.

Keep the rear door closed when operating the machine. Failure to do so could seriously injure a bystander.

P–10351

W–2020–1285

P–10350

B

Adjusting The Rear Door

2

The door latch catch (Item 1) [B] can be adjusted side to side for alignment with the door latch mechanism.

The door latch mechanism (Item 2) [B] can be adjusted backward or forward for alignment with the door catch.

1

P–10352

50

P–10339

873 Bobcat Loader Operation & Maintenance Manual

REAR GRILL 3.

Open the rear door.

A

Lift the panel over the top of the muffler and put it on top of the rear grill [A].

P–10429

Lift and pull the rear grill and remove it from the loader [B].

B

P–10354

51

873 Bobcat Loader Operation & Maintenance Manual

AIR CLEANER SERVICE

A

Without BOSS® – Condition Indicator: Replace the large (outer) filter element only when the red ring shows in the window of the condition indicator (Item 1) [A].

1

NOTE: Before replacing the filter element, push the button on the condition indicator (Item 1) [A].

Start the engine then stop the engine. If the red ring does not show, do not replace the filter element.

Replace the inner filter every third time the outer filter is replaced or when the red ring still shows in the indicator window after the outer filter has been replaced.

P–10374

With BOSS®: It is important to change the air filter element only when the service codes (on the optional instrument panel) shows the symbols [AF.2] [B].

B

MC–02322

52

873 Bobcat Loader Operation & Maintenance Manual

AIR CLEANER SERVICE (Cont’d)

A

Release the three dust cover fasteners (Item 1) [A].

1

Remove the dust cover.

P–10353

B

Remove the large filter element [B].

NOTE: Make sure all sealing surfaces are free of dirt and debris.

Install the new large filter element.

Align the tab on the cover with the slot on the air cleaner housing.

Push dust cover into place and secure with wire fasteners.

Check the air intake hose for damage. Check the air cleaner housing for damage. Check to make sure all connections are tight.

P–10363

Only replace the inner filter element [C] under the following conditions: •

Replace the inner filter element every third time the outer filter is replaced.

•

When the service codes on the instrument panel shows symbol [AF.2] during full engine speed, replace the inner filter element only after the outer filter element has been changed.

C

P–10362

53

873 Bobcat Loader Operation & Maintenance Manual

FUEL SYSTEM Fuel Specifications Use only clean, high quality diesel fuel, Grade No. 2 or Grade No. 1.

A

The following is one suggested blending guideline which should prevent fuel gelling problems during cold temperatures: Temp. F° (C°) No. 2 No.1 100% 0% +15o(9o) Down to –20o (–29o) 50% 50% Below –20o (29o) 0% 100% Contact your fuel supplier for local recommendations.

1

P–10107

Filling The Fuel Tank

B 2

Stop and cool the engine before adding fuel.

NO SMOKING! Failure to obey warnings can cause an explosion or fire.

W–2063–0887

Remove the fuel fill cap (Item 1) [A].

Use a clean, approved safety container to add fuel of the correct specifications. Add fuel only in an area that has free movement of air and no open flames or sparks. NO SMOKING!.

1

Install and tighten the fuel fill cap [A].

Fuel Filter See the SERVICE SCHEDULE Page 39 for the recommended service interval when to remove the water from the fuel filter.

Loosen the drain (Item 1) [B] at the bottom of the filter element to drain any water from the filter.

3

See the SERVICE SCHEDULE Page 39 for the recommended service interval when to replace the fuel filter.

Remove the filter element [B].

P–10803

Clean the area around the filter housing. Put oil on the seal of the new filter element. Install the fuel filter, and hand tighten. Remove the air from the fuel system.

Removing Air From The Fuel System After replacing the fuel filter element or when the fuel tank has run out of fuel, the air must be removed from the fuel system before starting the engine.

Loosen the air vent plug (Item 2) [B] at the top of the fuel filter.

Always clean up spilled fuel or oil. Keep heat, flames, sparks or lighted tobacco away from fuel and oil. Failure to use care around combustibles can cause explosion or fire which can result in injury or death.

Squeeze the priming bulb (Item 3) [B] until fuel flows from the vent.

W–2103–1285

Tighten the air vent plug.

54

873 Bobcat Loader Operation & Maintenance Manual

ENGINE LUBRICATION SYSTEM 4.

Checking Engine Oil Check the engine oil level every day before starting the engine for the work shift. Open the rear door and remove the dipstick (Item 1) [A].

A

2

4

Keep the oil level between the marks on the dipstick.

Engine oil is also used to provide engine cooling. Check oil level every day for correct engine lubrication and cooling.

1

3

Use a good quality motor oil that meets API Service Classification of CD or better (See Oil Chart, right).

Replacing The Oil And Filter

P–10801

See the SERVICE SCHEDULE Page 39 for the service interval for replacing the engine oil and filter.

B

Run the engine until it is at operating temperature. Stop the engine. Open the rear door.

1

Open the rear door. Remove the drain plug (Item 2) [A].

Drain the oil into container and dispose of used oil in an environmentally safe manner. Reinstall the drain plug.

Remove the oil filter (Item 1) [A].

Clean the filter housing surface. Put clean oil on the new oil filter gasket. Install the filter and hand tighten only.

Use only genuine Bobcat filter.

N–18292

Remove the fill cap (Item 2) [A].

Put 10 qts. (9,5L) of oil in the engine. Start the engine and let it run for several minutes. Stop the engine. Check for leaks and check the oil level.

RECOMMENDED SAE VISCOSITY NUMBER (LUBRICATION OILS FOR DIESEL ENGINE CRANKCASE)

C° –40

–34

–29

–23

–18

–13

–7

–1

+4

+10

+15

Remove the dipstick (Item 3) [A]. Check the oil level.

+21

+27

+32

+38

+43 +49

SAE 40W or 20W–50

Add oil as needed if it is not at the top mark on the dipstick (Item 1) [B].

SAE 10W–30 SAE 15W–40 SAE 30W

* SAE 5W–30 SAE 20W–20

Always clean up spilled fuel or oil. Keep heat, flames, sparks or lighted tobacco away from fuel and oil. Failure to use care around combustibles can cause explosion or fire which can result in injury or death.

SAE 10W SYNTHETIC OIL Use recommendation from Synthetic Oil Mfgr.

W–2103–1285

–40 –30

–20

–10

0

+10

+20

+30

+40

+50

+60

+70

+80

+90 +100 +110 +120

F°

TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE (DIESEL ENGINES MUST USE API CLASSIFICATION CD, CF4, CG4 )

* Can be used ONLY when available with appropriate diesel rating.

55

873 Bobcat Loader Operation & Maintenance Manual

ENGINE COOLING SYSTEM

A

Cleaning Cooling System Check the cooling system every day to prevent overheating, loss of performance or engine damage.

Wear safety glasses to prevent eye injury when any of the following conditions exist: • When fluids are under pressure.

• Flying debris or loose material is present.

• Engine is running.

• Tools are being used.

P–10355

B

W–2019–1285

Remove the rear grill. (See REAR GRILL Page 51.)

Use air pressure or water pressure to clean the top of the oil cooler [A].

1

Remove the hair pin (Item 1) [B] (both sides) from the oil cooler.

P–10137

56

873 Bobcat Loader Operation & Maintenance Manual

ENGINE COOLING SYSTEM (Cont’d)

A

Cleaning The Cooling System (Cont’d) Raise the oil cooler [A].

Use air pressure or water pressure to clean the top of the engine oil cooler.

P–10133

NOTE: The access cover (both sides) must be in place to ensure proper air flow through the oil cooler which will ensure correct cooling for the engine/hydraulic system [B].

B Access Cover

P–10085

ALTERNATOR BELT

C

Adjusting The Alternator Belt Stop the engine.

1

Loosen the alternator mounting and adjustment bolts (Item 1) [C].

2

P–10357

P–10358

Move the alternator until the belt has 5/16 inch (8,0 mm) movement at the middle of the belt span with 15 lbs. (66 N) of force (Item 2) [C].

Tighten the adjustment and mounting bolts.

57

873 Bobcat Loader Operation & Maintenance Manual

TIMING BELT

A

The timing belt (Item 1) [A] MUST be replaced every 3,000 hours or every 5 years.

1

P–05298

ELECTRICAL SYSTEM

B

Description The loader has a 12 volt, negative ground alternator charging system. The electrical system is protected by fuses located in the engine compartment. The fuses will protect the electrical system when there is an electrical overload. The reason for the overload must be found before starting the engine again.

Electrical System Maintenance The battery cables must be clean and tight. Check the water level in the battery. (See the SERVICE SCHEDULE Page 39 for correct interval.) Remove any acid or corrosion from the battery and cables with a sodium bicarbonate (baking soda) and water solution [B].

P–09589

Put Battery Saver (6664458) or grease on the battery terminals and cable ends to prevent corrosion.

Batteries contain acid which burns eyes and skin on contact. Wear goggles, protective clothing and rubber gloves to keep acid off body.

In case of acid contact, wash immediately with water. In case of eye contact get prompt medical attention and wash eye with clean, cool water for at least 15 minutes.

If electrolyte is taken internally drink large quantities of water or milk! DO NOT induce vomiting. Get prompt medical attention.

W–2065–1296

58

873 Bobcat Loader Operation & Maintenance Manual

ELECTRICAL SYSTEM (Cont’d)

A

Fuse Location The electrical system for this model loader is protected by fuses (Item 1) [A] located at the right side of the engine.

2

The fuse capacity and circuits are shown on the decal (Item 2) [A] and below.

1

P–10366

Fuse Capacity

Circuit

10 AMP. 15 AMP. 10 AMP. 15 AMP. (or 25 AMP) 25 AMP. 25 AMP. 25 AMP. 25 AMP.

BICS™ Engine BOSS® P.W.M. (or AHC) Lights Brake Accessory Accessory

B

P–10365

59

873 Bobcat Loader Operation & Maintenance Manual

ELECTRICAL SYSTEM (Cont’d)

A

Using A Booster Battery (Jump Starting) If it is necessary to use a booster battery to start the engine, BE CAREFUL! There must be one person in the operator’s seat and one person to connect and disconnect the battery cables.

2 4

Batteries contain acid which burns eyes and skin on contact. Wear goggles, protective clothing and rubber gloves to keep acid off body.

P–10813

In case of acid contact, wash immediately with water. In case of eye contact get prompt medical attention and wash eye with clean, cool water for at least 15 minutes.

1 3

If electrolyte is taken internally drink large quantities of water or milk. DO NOT induce vomiting. Get prompt medical attention.

W–2065–1296

Keep arcs, sparks, flames and lighted tobacco away from batteries. When jumping from booster battery make final connection (negative) at engine frame.

P–10808

Do not jump start or charge a frozen or damaged battery. Warm battery to 60oF. (16oC.) before connecting to a charger. Unplug charger before connecting or disconnecting cables to battery.

Never lean over battery while boosting, testing or charging.

Battery gas can explode and cause serious injury.

W–2066–1296

Damage to the alternator can occur if:

• Engine is operated with battery cables disconnected.

The ignition must be in the OFF position. The booster battery to be used must be 12 volt.

• Battery cables are connected when using

a fast charger or when welding on the loader (Remove both cables from the battery).

• Extra battery cables (booster cables) are connected wrong.

Connect the end of the first cable (Item 1 [A] to the positive (+) terminal of the booster battery. Connect the other end of the same cable (Item 2) [A] to the positive terminal on the starter.

I–2023–1285

Connect the end of the second cable (item 3) [A] to the negative (–) terminal of the booster battery. Connect the other end of the same cable (Item 4) [A] to the ground cable connection on the engine mounting bracket.

Keep the cables away from moving parts. Start the engine. (See STARTING THE ENGINE, Cold Temperature Starting Page 20 or 22.

After the engine has started, remove the ground (–) cable (Item 4) [A] first.

Remove the cable from the starter.

60

873 Bobcat Loader Operation & Maintenance Manual

ELECTRICAL SYSTEM (Cont’d)

A

Removing And Installing The Battery

1

2 Batteries contain acid which burns eyes and skin on contact. Wear goggles, protective clothing and rubber gloves to keep acid off body.

P–10811

In case of acid contact, wash immediately with water. In case of eye contact get prompt medical attention and wash eye with clean, cool water for at least 15 minutes.

B 1

If electrolyte is taken internally drink large quantities of water or milk. DO NOT induce vomiting. Get prompt medical attention.

W–2065–1296

Open the rear door.

Disconnect the negative (–) cable (Item 1) [A] from the battery.

Disconnect the main frame ground bolt and cable clamp (Item 2) [A]

P–10809

Remove the battery hold down clamp (Item 1) [B].

C

1

Disconnect the positive (+) cable (Item 1) [C] from the battery.

Remove the battery from the loader.

P–10806

61

873 Bobcat Loader Operation & Maintenance Manual

ELECTRICAL SYSTEM (Cont’d)

A

Removing And Installing The Battery (Cont’d) Always clean the terminals and cable ends when installing a new battery [A].

When installing the battery in the loader, do not touch any metal parts with the battery terminals.

Connect and tighten the battery cables.

Install cable clamp and ground bolt (Item 1) [B] as shown for correct ground and cable routing.

Connect the negative (–) cable last to prevent sparks.

P–09589

P–09590

B Keep arcs, sparks, flames and lighted tobacco away from batteries. When jumping from booster battery make final connection (negative) at engine frame.

1

Do not jump start or charge a frozen or damaged battery. Warm battery to 60°F. (16°C.) before connecting to a charger. Unplug charger before connecting or disconnecting cables to battery.

Never lean over battery while boosting, testing or charging.

P–10814

Battery gas can explode and cause serious injury.

W–2066–1296

C

Sight Gauge

HYDRAULIC/HYDROSTATIC SYSTEM Checking And Adding Fluid 5.

Use only recommended fluid in the hydraulic system.

(See SPECIFICATIONS Page 89.)

P–04613

Put the Bobcat loader on a level surface. Lower the lift arms and tilt the Bob–Tach fully back.

Check the fluid level at the sight gauge [C]. The fluid level must show in the sight gauge.

P–10094

If fluid is needed, remove the fill cap (Item 1) [D].

D

Add the fluid as needed to bring the level to the sight gauge.

NOTE: Before installing the fill cap, make sure the rubber gasket is installed on the fill cap [D].

Install the fill cap [D].

1

CD–12250

62

P–10096

873 Bobcat Loader Operation & Maintenance Manual

HYDRAULIC/HYDROSTATIC SYSTEM (Cont’d)

A

Replacing Hydraulic Fluid When replacing the hydraulic fluid, always replace the hydraulic/hydrostatic filter (See Replacing Hydraulic/Hydrostatic Filter Page 64) and also clean the hydraulic fill screen and the case drain filters.

See the SERVICE SCHEDULE Page 39 for the correct service interval.

Replace the fluid if it becomes contaminated or after major repair.

1

Remove the fill cap and raise the operator cab. (See Raising The Operator Cab Page 42.)

N–17717

B

Hydraulic Fill Screen Remove two hose clamps and remove the hose (Item 1) [A].

Remove the hydraulic fill screen (Item 1) [B] and use clean solvent to remove any contamination from the screen.

1

Use air pressure to dry the screen.

Install screen, hose and hose clamps.

N–17718

C

Case Drain Filters

1

Remove the hydrostatic motor covers (Item 1) [C]. (Both sides.)

P–10099

Pull the reservoir drain hose [D] out the left motor cover hole. Remove the plug (Item 1) and drain the fluid into a container.

D

Always clean up spilled fuel or oil. Keep heat, flames, sparks or lighted tobacco away from fuel and oil. Failure to use care around combustibles can cause explosion or fire which can result in injury or death.

1

W–2103–1285 P–10090

63

873 Bobcat Loader Operation & Maintenance Manual

HYDRAULIC/HYDROSTATIC SYSTEM (Cont’d)

RIGHT CASE DRAIN FILTER

A

Case Drain Filters (Cont’d) Disconnect the hoses from the hydrostatic motor case drain filter (Item 1) [A] and [B] Remove the case drain filters (Item 1) [A] and [B] and clean thoroughly with clean solvent.

1

Install the case drain filters and tighten the hoses.

Install the plug in the reservoir drain hose and tighten.

Install the motor covers. (Both sides.)

Add the correct fluid to the reservoir until the fluid level is at the sight gauge. (See Checking And Adding Fluid Page 62.)

N–17751

LEFT CASE DRAIN FILTER

B

Replacing Hydraulic/Hydrostatic Filter 6.

1

See the SERVICE SCHEDULE Page 39 for the correct service interval.

Raise the operator cab (See Raising The Operator Cab Page 42.)

N–17750

Remove the filter (Item 1) [C].

C

Clean the surface of the filter housing where the element seal contacts the housing. Put clean oil on the rubber seal of the filter element.

Install and hand tighten the filter element.

1 Diesel fuel or hydraulic fluid under pressure can penetrate skin or eyes causing serious injury. Fluid leaks under pressure may not be visible. Use a piece of cardboard or wood to find leaks. Do not use your bare hand. Wear safety goggles. If fluid enters skin or eyes, get immediate medical attention.

N–17720

W–2074–1285

Always clean up spilled fuel or oil. Keep heat, flames, sparks or lighted tobacco away from fuel and oil. Failure to use care around combustibles can cause explosion or fire which can result in injury or death.

W–2103–1285

Lower the operator cab. Start the engine and operate the loader hydraulic controls. Stop the engine. Check for leaks. Check the fluid level in the reservoir and add as needed.

64

873 Bobcat Loader Operation & Maintenance Manual

TIRE MAINTENANCE

A

Wheel Nuts See SERVICE SCHEDULE Page 39 for the service interval to check the wheel nuts. The correct torque is 105–115 ft.–lbs. (142–156 Nm) torque [A].

Tire Rotation Check the tires regularly for wear, damage and pressure.

P–10142

B

Inflate tires to the MAXIMUM pressure shown on the sidewall of the tire. DO NOT mix brands of tires used on the same loader.

I–2057–0794

Rear tires usually wear faster than front tires. To keep tire wear even, move the front tires to the rear and rear tires to the front [B].

It is important to keep the same size tires on each side of the loader. If different sizes are used, each tire will be turning at a different rate and cause excessive wear. The tread bars of all the tires must face the same direction.

B–09976

Recommended tire pressure must be maintained to avoid excessive tire wear and loss of stability and handling capability. Check for the correct pressure before operating the loader.

Tire Mounting Tires are to be repaired only by an authorized person using the proper procedures and safety equipment. Tires and rims must always be checked for correct size before mounting. Check rim and tire bead for damage.

Do not inflate tires above specified pressure.

Failure to use correct tire mounting procedure can cause an explosion which can result in injury or death.

W–2078–1285

The rim flange must be cleaned and free of rust. The tire bead and rim flange must be lubricated with a rubber lubricant before mounting the tire, avoid excessive pressure which can rupture the tire and cause serious injury or death. During inflation of the tire, check the tire pressure frequently to avoid over inflation.

65

873 Bobcat Loader Operation & Maintenance Manual

FINAL DRIVE TRANSMISSION (CHAINCASE)

A

Checking And Adding Oil The chaincase contains the final drive sprockets and chains and uses the same type of oil as the hydraulic/hydrostatic system. (See SPECIFICATIONS Page 89 for correct fluid type.)

1

Park the loader on a level surface.

Stop the engine.

Remove the plug (Item 1) [A] from the front of the chaincase housing.

P–10153

If oil can be reached with the tip of the your finger through the hole, the oil level is correct

B

If the level is low, add oil through the check plug hole until the oil flows from the hole.

Install and tighten the plug.

Removing Oil From The Chaincase To drain the oil from the chaincase, remove the cover (Item 1) [B] over the drain plug at the rear of the chain case.

1

P–01616

C

Remove the drain plug (Item 1) [C] and drain the oil into a container.

Dispose of the used oil in an environmentally safe manner.

NOTE: When installing the drain plug into the chaincase, always use a NEW drain plug.

1

P–01619

66

873 Bobcat Loader Operation & Maintenance Manual

FAN GEARBOX

A

Checking And Maintaining See SERVICE SCHEDULE Page 39 for the correct service interval.

Raise the operator cab. (See Raising The Operator Cab Page 42.)

Remove the plug (Item 1) [A].

Be sure the level does not go above the top of the shaft in the gearbox [A].

Gear Lube Level

1

Use SAE 90W gear lube if the level is low.

P–04671

B

DRIVE BELT

2

Adjusting The Drive Belt 7.

The drive belt idler arm stop is located on the left side of the engine below the air cleaner [B].

1

Loosen the two bolts (Item 1) [B] and slide the stop against the idler arm. Tighten the bolts.

There is no adjustment for the spring, just make sure the spring bolt (Item 2) [B] is tight.

P–05554

2

P–10805

67

873 Bobcat Loader Operation & Maintenance Manual

DRIVE BELT (Cont’d)

A

Replacing The Drive Belt Stop the engine.

2

Open the rear door.

Remove the three belt shield fasteners (Item 1) [A].

1

Remove the belt shield (Item 2) [A] from the drive belt housing.

P–10814

B

Loosen the two stop mounting bolts (Item 1) [B].

1

Loosen the spring tension bolt (Item 2) [B].

Remove the fan drive belt from the tensioner pulley.

2

Remove the drive belt from the hydrostatic pump pulley and flywheel pulley.

P–10805

C

Remove the drive belt (Item 1) [C].

Install new drive belt and adjust the drive belt idler arm stop (See Adjusting the Drive Belt Idler Arm Stop Page 67.).

1 P–10804

68

873 Bobcat Loader Operation & Maintenance Manual

LUBRICATING THE BOBCAT LOADER 8.

See the SERVICE SCHEDULE Page 39 for lubrication intervals. Lubricate regularly the best performance of the loader.

A

Record the operating hours each time you lubricate the Bobcat loader.

Always use a good quality lithium based multi–purpose grease when you lubricate the loader. Apply the lubricant until extra grease shows.

1

Lubricate the following locations on the loader: 1. Rod End Lift Cylinder (Both Sides) [A].

P–10097

2. Base End Lift Cylinder (Both Sides) [B].

B

2 P–10098

C

3. Lift Arm Pivot Pin (Both Sides) [C].

3

P–10100

4. Lift Arm Link Pivot (Both Sides) [D].

D 4

P–10102

69

873 Bobcat Loader Operation & Maintenance Manual

LUBRICATING THE BOBCAT LOADER (Cont’d)

A

5. Base End Tilt Cylinder (Both Sides) [A].

5

P–10106

B

6. Rod End Tilt Cylinder (Both Sides) [B].

7. Bob–Tach Pivot Pin (Both Sides [B].

6

7 P–10150

8. Bob–Tach Wedge (Both Sides) [C].

C 8

P–10148

9. Control Link (Both Sides) [D].

D

9

P–10101

70

873 Bobcat Loader Operation & Maintenance Manual

LUBRICATING THE BOBCAT LOADER (Cont’d)

A

10. Control Link (Both Sides) [A]

10

P–10104

.

B

11. 250 Hours: Steering Lever Shaft (3) [B].

11

P–10105

71

873 Bobcat Loader Operation & Maintenance Manual

BOB–TACH

A

873Operation&MaintenanceManual(S/N514123810&Above)#6900791–PreventiveMaintenanceSection

Inspection And Maintenance Move the Bob–Tach levers to engage the wedges [A].

The levers and wedges must move freely.

1

The wedges must extend through the holes in the attachment mounting frame (Item 1) [A].

N–17042 N–17041

Bob–Tach wedges must extend through the holes in attachment. Levers must be fully down and locked. Failure to secure wedges can allow attachment to come off and cause injury or death.

B

W–2102–0588

The spring loaded wedge (Item 1) [A] must contact the lower edge of the hole in the attachment (Item 1) [B] and [C].

If the wedge does not contact the lower edge of the hole [B] and [C], the attachment will be loose and can come off the Bob–Tach.

1

N–17039

C

Bob–Tach Wedge

Wedge Must Contact Lower Edge Of Hole In The Attachment

Inspect the mounting frame on the attachment and the Bob–Tach, linkages and wedges for excessive wear or damage [D]. Replace any parts that are damaged, bent, or missing. Keep all fasteners tight.

D

Look for cracked welds. Contact your Bobcat dealer for repair or replacement parts.

Lubricate the wedges (See SERVICE SCHEDULE, Page 39 and LUBRICATION OF THE BOBCAT LOADER, Page 69).

TS–01062

72

873 Bobcat Loader Operation & Maintenance Manual

SYSTEMS ANALYSIS 12.

ADVANCED HAND CONTROLS Troubleshooting Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77 AUXILIARY HYDRAULICS OPERATION Troubleshooting Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 BOBCAT INTERLOCK CONTROL SYSTEM (BICS™) Troubleshooting Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77 MONITOR SERVICE CODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 SERVICE CODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

SYSTEMS ANALYSIS

73

873 Bobcat Loader Operation & Maintenance Manual

74

873 Bobcat Loader Operation & Maintenance Manual

SERVICE CODES The following list references the defect codes that are transmitted to the instrument panel (BOSS Display).

Some service procedures for correcting the problems can be found in this manual and other procedures must be performed ONLY BY QUALIFIED BOBCAT SERVICE PERSONNEL.

Instructions are necessary before operating or servicing machine. Read Operation & Maintenance Manual, Handbook and signs (decals) on machine. Follow warnings and instructions in the manuals when making repairs, adjustments or servicing. Check for correct function after adjustments, repairs or service. Failure to follow instructions can cause injury or death.

W–2003–0797

SUBJECT Engine Temperature

Engine Oil Pressure

Engine Speed

Air Filter Battery Fuel Level

DISPLAY READS

CONDITION

EC–1.1 EC–2.1 EC 3 EC 4

SHUTDOWN, Engine Temperature WARNING, Engine Temperature Wiring Not Connected Wiring Shorted

EC 5 EC 7 EP 1 EP 2

High Sensor Voltage Sensor Out Of Range SHUTDOWN, Pressure WARNING, Pressure

EP 3 EP 4 EP 5

Wiring Not Connected Wiring Shorted High Sensor Voltage

EP 7 ES 1 ES–2.1 ES–6

Sensor Out Of Range SHUTDOWN, Engine Speed Too High WARNING, Engine Speed Slightly High Sensor No Signal

ES–7 AF 2 AF 6 b–2.1

Sensor Out Of Range WARNING, Restriction Too High Sensor No Signal WARNING, Bad Battery

b–2.2 FUEL2 FUEL3 FUEL4

WARNING, Battery Voltage WARNING, Low Level Wiring Not Connected Wiring Shorted

FUEL5 FUEL7

High Sensor Voltage Sensor Out Of Range

75

873 Bobcat Loader Operation & Maintenance Manual

SUBJECT

DISPLAY READS

Hydrostatic Charge Filter Conditions

Return Filter Condition (853, 863, 873 Only) Hydrostatic Fluid

Hydrostatic Fluid Temperature

CONDITION

HF1–2 HF1–6 HF2–2 HF2–6 HF2–2 HF2–6

WARNING, High Restriction (1st Filter) Sensor No Signal WARNING, High Restriction (2nd Filter) Sensor No Signal WARNING, High Restriction Sensor No Signal

HP 1 HP 2 HP 3 HP 4 HP 5 HP 7 HC 1 HC 2 HC 3 HC 4 HC 5 HC 7

SHUTDOWN, Pressure WARNING, Pressure Wiring Not Connected Wiring Shorted High Sensor Voltage Sensor Out Of Range SHUTDOWN, Temperature WARNING, Temperature Wiring Not Connected Wiring Shorted High Sensor Voltage Sensor Out Of Range

AUXILIARY HYDRAULICS OPERATION Troubleshooting Chart The Auxiliary Hydraulics Control has a built–in diagnostics function.

The two lights will blink in a specific pattern to indicate a problem (See Below).

1 2 P–3272

INDICATIONS Blinking Momentary Light (Item 1) Detent Light (Item 2) Problem

Causes

Check

Off

Blinking

X

Off X

X Base Solenoid

X Rod Solenoid

Blinking

Off

Blinking

X

X

At same time

Alternating

X

X

Diverter Solenoid

Wires Disconnected Wires Shorted Wires Cut Solenoid Failed

Off

Right Handle

Spring in the thumb switch is broken

Check for voltage (1–10 volts) at the solenoid connector.

Check for the thumb switch in centered position. Check for voltage to Dk. Blue & Dk. Blue/White wires.

NOTE: Check all of the above first. Any of the above can also indicate a problem with the Auxiliary Control Module. See your Bobcat dealer for module replacement.

76

873 Bobcat Loader Operation & Maintenance Manual

BOBCAT INTERLOCK CONTROL SYSTEM (BICS™) 14.

Troubleshooting Chart The following list shows the effects which can happen to the loader, and the probable causes when the BICS Controller lights are off or flashing. Have the service procedure performed ONLY BY QUALIFIED BOBCAT SERVICE PERSONNEL.

Indicator Light System Activated

Light ON

PRESS TO OPERATE PRESS TO OPERATE Lift, tilt and traction button is activated button not activated functions will not operate.

Seat Bar Seat Bar Down.

Valve

Traction

Light OFF

Flashing Indicator Means System Problem (See Your Bobcat Dealer for Service) Effect on Operation of Loader When Light Is Number of OFF Flashes Cause

Control Valve Can Be Used.

Loader can be moved forward & backward.

Seat Bar Up.

Control Valve Cannot Be Used.

Lift, tilt and traction functions will not operate.

Lift and tilt functions will not operate.

Loader cannot be Loader cannot be moved forward and moved forward and backward. backward.

2 3 2 3 2 3 3 1 2 3 4 5 6

Power

BICS Controller is operating correctly.

BICS Controller is not operating correctly.

Lift, tilt and traction functions will not operate.

N/A

System Activated circuit shorted to battery voltage*.

System Activated circuit shorted to ground.

Seat bar sensor circuit shorted to battery voltage*.

Seat bar sensor circuit shorted to ground.

Valve output circuit shorted to battery voltage*.

Valve output circuit shorted to ground.

Valve output circuit is not grounded.

Traction lock hold coil circuit is open.

Traction lock hold coil circuit shorted to battery voltage*.

Traction lock hold coil circuit shorted to ground.

Traction lock pull coil circuit is open.

Traction lock pull coil circuit is shorted to battery voltage*.

Traction lock pull coil circuit is shorted to ground.

N/A

* Normal BICS operating voltage is less than the electrical system voltage. If voltage is more, the circuit is shorted to system voltage.

NOTES: (1) If the System Activated and/or seat bar sensor circuits are open, the corresponding lights will be OFF. If one of the lights stay OFF, check the circuit for continuity. See Inspection & Maintenance Instructions in Preventive Maintenance section.

(2) If all five lights flash repeatedly, the voltage supply is greater than 16 volts or less than 9 volts.

(3) Flashing patterns will repeat every 3.25 seconds.

ADVANCED HAND CONTROLS (AHC) 13.

Troubleshooting Chart The AHC has a built–in diagnostic function which uses the two lights on the left handle.

Both lights will be ON when the AHC is functioning correctly. The lights will flash in a specific pattern to indicate a problem (See Below). (See your Bobcat dealer for service information.)

Number of Flashes Left Hand Light (Lift Circuit) Right Hand Light (Tilt Circuit)

1 Handle Not Calibrated

FLASHING LIGHT MEANS SYSTEM PROBLEM (See Your Bobcat Dealer for Service) 2 3 4 Actuator Not Calibrated

Wiring Fault (Handle)

Wiring Fault (Actuator)

5 Actuator Fault

NOTE: Flashing patterns will repeat every six seconds. One blink will occur if Right or Left Hand Control is not in neutral position before key is turned ON or engine is started and green PRESS TO OPERATE button is activated.

77

873 Bobcat Loader Operation & Maintenance Manual

78

873 Bobcat Loader Operation & Maintenance Manual

MACHINE SIGN TRANSLATIONS 15.

IMPORTANT (6708937) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 WARNING (6579510 – Foot Pedal) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82 WARNING (6703725 – Hand Control) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83 SERVICE SCHEDULE (6715563) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84 WARNING (6579528, 6577754, 6579639, 6579509, 6508941) . . . . . . . . . . 86 DANGER (6717343) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87 WARNING (6715944) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

MACHINE SIGN TRANSLATIONS

MACHINE SIGNS (DECALS) Machine signs (decals) are an esential part of the loader. (See Pages xiv & xv.) This section provides French and Spanish translations of the machine signs that are in English.

79

873 Bobcat Loader Operation & Maintenance Manual

80

873 Bobcat Loader Operation & Maintenance Manual

IMPORTANTE (SPANISH) 873 ESTE MODELO DE CARGADOR VIENNE EQUIPADO DE FÁBRICA CON UN SISTEMA DE ESCAPE CON DISPOSITIVO PARACHISPAS APROBADO POR EL SERVICIO FORESTAL DEL MINISTERIO DE AGRICULTURA DE LOS ESTADOS UNIDOS. EL TURBOALIMENTADOR DEBE ESTAR FUNCIONANDO PARA MANTENER OPERANDO EL SISTEMA DE ESCAPE CON DISPOSITIVO PARACHISPAS. SI SE OPERA ESTA MÁQUINA EN BOSQUES INFLAMABLES, MATORRALES O TERRENOS CUBIERTOS DE PASTOS, ÉSTA DEBE ESTAR EQUIPADA CON UN DISPOSITIVO PARACHISPAS CONECTADO AL SISTEMA DE ESCAPE Y DEBE MANTENERSE EN BUENAS CONDICIONES DE FUNCIONAMIENTO. EL NO HAVERLO CONSTITUYE UNA VIOLACIÓN A LA LEY DEL ESTADO DE CALIFORNIA, SECCIÓN 4442. PRC. CONSULTE LAS LEYES Y REGULACIONES LOCALES SOBRE REQUISITOS RELACIONADOS CON LOS DISPOSITIVOS PARACHISPAS. PARA MAS INSTRUCCIONES, CONSULTE EL MANUAL DE OPERACIÓN Y MANTENIMIENTO.

IMPORTANT (FRENCH) 873 LE SYSTÈME D’ÉCHAPPEMENT DE CETTE CHARGEUSE EST ÉQUIPÉ D’UN PARA–ÉTINCELLES INSTALLÉ EN USINE ET APPROUVÉ PAR LE SERVICE DES FORÊTS DU DÉPARTMENT DE L’AGRICULTURE DES ÉTATS–UNIS (U.S.D.A. FORESTRY SERVICE).

LE TURBOCOMPRESSEUR DOIT ÊTRE EN BON ÉTAT DE MARCHE POUR QUE LE SYSTÈME D’ÉCHAPPEMENT À PARE–ÉTINCELLE FONCTIONNE. SI CETTE MACHINE EST UTILISÉE SUR UN TERRAIN COUVERT D’ARBRES, DE BROUSSAILLES, OU D’HERBAGES INFLAMMABLES, SON SYSTÈME D’ÉCHAPPEMENT DOIT ÊTRE ÉQUIPÉD D’UN PARE–ÉTINCELLE ET MAINTENU EN BON ÉTAT DE FONCTIONNEMENT. CETTE EXIGENCE EST IMPOSÉE PAR LA LOI DE L’ÉTAT DE LA CALIFORNIE, SECTION 4442. PRC. CONSULTER LA RÉGLEMENTATION LOCALE RELATIVE AUX PARE–ÉTINCELLES. CONSULTER LE MANUEL DE L’OPÉRATEUR ET D’ENTRETIEN POUR DE PLUS AMPLES RENSEIGNEMENTS.

81

873 Bobcat Loader Operation & Maintenance Manual

Solamente con control de piso

Commande au pied seulement

ADVERTENCIA (SPANISH)

ATTENTION (FRENCH)

EVITE HERIDAS O LA MUERTE

EVITER LES BLESSURES OU LA MORT

NO USE NUNCA EL CARGADOR SIN LEER LAS INSTRUCCIONES. LEA EL MANUAL DEL OPERATIO, EL MANUAL DE SERVICIO Y LA GIA DEL OPERARIO.

NE JAMAIS SE SERVIR DE LA CHARGEUSE SANS INSTRUCTIONS. LIRE LE MANUEL DE L’OPERATEUR EL D’ENTRETIEN AINSI QUE LE GUIDE D’UTILISATION.

NO VIAJE O DE LA VUELTA CON LOS BRAZOS DE ELEVACION ARRIBA. CARGUE, DESCARGUE Y DE LA VUELTA ESTANDO EN UN SITIO PLANO Y NIVELADO. NO EXCEDA LA CAPACIDAD NOMINAL DE FUNCIONAMIENTO (VEA EL AVISO EN EL CARGADOR).

NE PAS SE DEPLACER NI VIRER AVEC LE BRAS RELEVES. CHARGER, DECHARGER ET VIRER SUR UN SOL PLAT ET HORIZONTAL. NE PAS DEPASSER LE CAPACITE NOMINALE (CONSULTER L’AUTOCOLLANT APPOSE SUR LA CARGEUSE).

USE LA BARRA DEL ASIENTO. ASEGURESE BIEN EL CINTURON DE SEGURIDAD.

UTILISER L’ARCEAU DE SECURITE. ATTACHER SOIGNEUSEMENT LA CEINTURE DE SECURITE.

NUNCA MODIFIQUE EL EQUIPO NI USE ADITAMENTOS QUE NO ESTEN APROBADOS POR LA COMPAÑIA BOBCAT.

NE JAMAIS MODIFIER L’EQUIPEMENT NI SE SERVIR D’ACCESSOIRES QUE NE SONT PAS APPROUVES PAR BOBCAT COMPANY.

MANTENGA LOS PIES EN LOS PEDALES. MAINTENIR LES PIEDS SUR LES PEDALES. EN LA PENDIENTES, MANTENGA EL EXTREMO PESADO DE CARGADOR EN POSICION ASCENDENTE.

DANS LES PENTES, TOUJOURS MAINTENIR LA PARTIE LA PLUS LOURDE DE LA CHARGEUSE VERS LE HAUT.

ANTES DE BAJARSE DEL CARGADOR POUR QUITTER LA CHARGEUSE: 1. BAJE LOS BRAZOS DE ELEVACION. COLOQUE EL ADITAMENTO BEIN EN EL SUELO. 2. PARE EL MOTOR

1. ABAISSER LES BRAS DE LEVAGE. POSER L’EQUIPEMENT A PLATE SUR LE SOL. 2. ARRETER LE MOTEUR.

3. PONGA EL FRENO.

3. ENCLENCHER LE FREIN DE STATIONNEMENT.

4. LEVANTE LA BARRA DEL ASIENTO. MUEVA LOS PEDALES HASTA QUE AMBOS SE TRABEN.

4. RELEVER L’ARCEAU DE SECURITE. DEPLACER LES PEDALES JUSQU’A CE QU’ELLES SOIENTE TOUTES DEUX VERROILLEES.

82

873 Bobcat Loader Operation & Maintenance Manual

Solamente con control de mano

Commande à la main seulement

ADVERTENCIA (SPANISH)

ATTENTION (FRENCH)

EVITE HERIDAS O LA MUERTE

EVITER LES BLESSURES OU LA MORT

NO USE NUNCA EL CARGADOR SIN LEER LAS INSTRUCCIONES. LEA EL MANUAL DEL OPERATIO, EL MANUAL DE SERVICIO Y LA GIA DEL OPERARIO.

NE JAMAIS SE SERVIR DE LA CHARGEUSE SANS INSTRUCTIONS. LIRE LE MANUEL DE L’OPERATEUR EL D’ENTRETIEN AINSI QUE LE GUIDE D’UTILISATION.

NO VIAJE O DE LA VUELTA CON LOS BRAZOS DE ELEVACION ARRIBA. CARGUE, DESCARGUE Y DE LA VUELTA ESTANDO EN UN SITIO PLANO Y NIVELADO. NO EXCEDA LA CAPACIDAD NOMINAL DE FUNCIONAMIENTO (VEA EL AVISO EN EL CARGADOR).

NE PAS SE DEPLACER NI VIRER AVEC LE BRAS RELEVES. CHARGER, DECHARGER ET VIRER SUR UN SOL PLAT ET HORIZONTAL. NE PAS DEPASSER LE CAPACITE NOMINALE (CONSULTER L’AUTOCOLLANT APPOSE SUR LA CARGEUSE).

USE LA BARRA DEL ASIENTO. ASEGURESE BIEN EL CINTURON DE SEGURIDAD.

UTILISER L’ARCEAU DE SECURITE. ATTACHER SOIGNEUSEMENT LA CEINTURE DE SECURITE.

NUNCA MODIFIQUE EL EQUIPO NI USE ADITAMENTOS QUE NO ESTEN APROBADOS POR LA COMPAÑIA BOBCAT.

NE JAMAIS MODIFIER L’EQUIPEMENT NI SE SERVIR D’ACCESSOIRES QUE NE SONT PAS APPROUVES PAR BOBCAT COMPANY.

MANTENGA LOS PIES EN LOS PEDALES. MAINTENIR LES PIEDS SUR LES PEDALES. EN LA PENDIENTES, MANTENGA EL EXTREMO PESADO DE CARGADOR EN POSICION ASCENDENTE.

DANS LES PENTES, TOUJOURS MAINTENIR LA PARTIE LA PLUS LOURDE DE LA CHARGEUSE VERS LE HAUT.

ANTES DE BAJARSE DEL CARGADOR POUR QUITTER LA CHARGEUSE: 1. BAJE LOS BRAZOS DE ELEVACION. COLOQUE EL ADITAMENTO BEIN EN EL SUELO. 2. PARE EL MOTOR

1. ABAISSER LES BRAS DE LEVAGE. POSER L’EQUIPEMENT A PLATE SUR LE SOL. 2. ARRETER LE MOTEUR.

3. PONGA EL FRENO.

3. ENCLENCHER LE FREIN DE STATIONNEMENT.

4. LEVANTE LA BARRA DEL ASIENTO. MUEVA LOS PEDALES HASTA QUE AMBOS SE TRABEN.

4. RELEVER L’ARCEAU DE SECURITE. DEPLACER LES PEDALES JUSQU’A CE QU’ELLES SOIENTE TOUTES DEUX VERROILLEES.

83

873 Bobcat Loader Operation & Maintenance Manual

• FILTRO DEL COMBUSTIBLE – quite el agua atrapada.

• BRAZO DE ELEVACIÓN DE LA CARGADORA, UNIONES DE

ADVERTENCIA (SPANISH) EVITE LESIONES O LA MUERTE

• Mantenga la puerta cerrada excepto durante tareas de mantenimiento

•

contactos eléctricos, partes móviles, partes calientes y escapes.

•

• Mantenga el motor libre de material inflamable • Mantenga el cuerpo, objetos sueltos y la vestimenta alejados de • No utilice la cargadora en un espacio con polvos o gases explosivos o con material inflamable cerca de un escape.

• Todos los gases de escape puede provocar la muerte. Siempre • • • • •

ventile.

Jamás utilice éter o fluidos de arranque en un motor diesel con bujías incandescentes. Utilice sólo dispositivos de arranque aprobados por el fabricante del motor.

Los fluidos que gotean bajo presión pueden penetrar en la piel y provocar lesiones graves. En ese caso, obtenga asistencia médica inmediata. Utilice anteojos de seguridad. Utilice un trozo de cartón al verificar la existencia de fugas.

Los ácidos de la batería ocasionan quemaduras graves, utilice anteojos de seguridad. Si el ácido entra en contacto con los ojos, la piel o la vestimenta, enjuague bien con agua. En caso de contacto con los ojos, enjuague y obtenga asistencia médica.

Las baterías producen gases explosivos e inflamables. Aleje arcos, chispas, llamas y tabaco encendido.

Para arranque en puente, conecte el cable negativo al motor de la cargadora en último lugar (jamás en la batería). Luego del arranque en puente, quite la conexión negativa del motor primero.

PROGRAMA DE MANTENIMIENTO (SPANISH)

•

CADA 50 HORAS

• FLUIDO HIDRÁULICO, MANGUERAS Y TUBERÍA – revise el • • •

nivel del fluido. Verifique que no existan daños o fugas. Repare o cambie según sea necesario.

TRANSMISIÓN DE DIRECCIÓN FINAL (caja de cadenas) – revise el nivel del fluido.

CONTROLES HIDRÁULICOS (PEDALES O CONTROLES MANUALES) Y PALANCAS DE DIRECCIÓN – revise la operación. Ajuste según sea necesario.

TUERCAS DE LAS RUEDAS – revise que no existan tuercas sueltas y ajuste según lo indicado en el manual de operación y mantenimiento.

• SILENCIADOR DEL SISTEMA PARACHISPAS – en los modelos 500 y 700 solamente. Vacíe la cámara de chispas.

• ACEITE DEL MOTOR – revise el nivel y agregue según sea •

•

CADA 100 HORAS

CADA 10 HORAS (ANTES DE ARRANCAR LA CARGADORA)

•

•

ELEVACIÓN, CILINDROS, PIVOTES Y CUÑAS DEL ENGANCHE RÁPIDO – lubrique con grasa multiuso a base de litio.

CINTURÓN DE SEGURIDAD, BARRA DE SEGURIDAD Y ENGANCHES DE CONTROL– revise las funciones. Repare o cambie según sea necesario. Limpie las partes móviles.

BICSMR – revise la función. Elimine desperdicios, suciedad u objetos debajo y/o detrás del asiento del operador según sea necesario.

NEUMÁTICOS – verifique la presión de aire. Infle los neumáticos con la presión MÁXIMA que se indica en la pared lateral del neumático.

GENERAL – verifique que no existan partes sueltas o rotas, que la cabina del operador no presente daños, revise la operación de los instrumentos, la existencia de tuercas sueltas, fugas de aceite, rótulos de seguridad dañados o faltantes. Repare o cambie según sea necesario.

necesario. No lo llene en exceso.

FILTRO DE AIRE DEL MOTOR – revise el indicador y/o el visor.

Repare sólo en caso de ser necesario.

SISTEMA DE AIRE DEL MOTOR – verifique que no existan fugas o componentes dañados.

SISTEMA DE REFRIGERACIÓN DEL MOTOR – limpie el refrigerador de aceite y las parrillas.

MODELOS 500 Y 700 – revise el nivel del fluido refrigerante frío, agregue 53% de propilenglicol premezclado con 47% de agua según sea necesario.

84

• BATERÍA – verifique que la batería no presente daños, revise las abrazaderas, las conexiones de los cables y el nivel de electrolito. Agregue agua destilada según sea necesario.

CADA 250 HORAS (O CADA 12 MESES)

• PIVOTES DE LA PALANCA DE DIRECCIÓN – lubrique con grasa multiuso a base de litio (3 lugares).

• CORREA DE DESPLAZAMIENTO DE TRANSMISIÓN –

modelos 700. Verifique que no se encuentre gastada o dañada.

Ajuste o cambie según sea necesario. *Revise las correas de desplazamiento cambiadas después de 50 horas de operación y ajústelas según sea necesario.

873 Bobcat Loader Operation & Maintenance Manual

• LÍNEA DE DESPLAZAMIENTO – modelos 500 solamente. • FILTRE À CARBURANT – Éliminez l’eau retenue.

Lubrique la junta U. • BRAS DE LEVAGE, AXES DE LEVAGE, VÉRINS, PIVOTS • ENGRANAJE DEL VENTILADOR – revise el nivel del fluido.

BOBTACH ET CLAVETTES – Lubrifiez avec une graisse à base de lithium de type universel.

• Revise todas las correas de desplazamiento. Revise el estado y la tensión de la bomba hidrostática y de agua, el alternador y • CEINTURE DE SÉCURITÉ, ARCEAU DE SÉCURITÉ ET •

el desplazamiento del ventilador. Ajuste o cambie según sea necesario.

BICSMR – revise el control de desvío de los brazos de elevación.

CADA 500 HORAS (O CADA 12 MESES)

• SISTEMA HIDRÁULICO/HIDROSTÁTICO – cambie la tapa del respiradero del depósito.

CADA 1000 HORAS (O CADA 12 MESES)

• DEPÓSITO HIDRÁULICO – cambie el fluido.

• TRANSMISIÓN DE DIRECCIÓN FINAL (CAJA DE CADENAS)

• • •

– cambie el fluido.

TOUTES LES 50 HEURES

AVERTISSEMENT (FRENCH)

• FLUIDE

ÉVITEZ DES BLESSURES OU LA MORT

• Gardez la portière fermée, sauf en cas d’intervention de service.

• Gardez la région du moteur exempte de matières inflammables.

• Gardez toute partie du corps, tout objet lâche et toute pièce de

•

•

•

• • • •

• •

ENCLENCHEMENTS SOLIDAIRES – Vérifiez leur bon fonctionnement. Réparez ou remplacez au besoin. Débarrassez les pièces mobiles de toute saleté et de tous débris.

BICSt – Vérifiez le bon fonctionnement. Débarrassez le dessous /ou l’arrière du siège de l’opérateur de tous débris, saletés et objets divers, le cas échéant.

PNEUS – Vérifiez la pression d’air. Gonflez à la valeur de pression MAXIMALE qui est indiquée sur le flanc du pneu.

GÉNÉRAL – Vérifiez si des pièces sont desserrées ou brisées, si la cabine de l’opérateur est en bon état, si les instruments fonctionnent correctement, si les écrous de roue sont bien serrés, s’il y a fuites d’huile, si des enseignes de sécurité sont endommagées ou ont été arrachées. Réparez ou remplacez au besoin.

vêtement à l’écart des points de contact électrique, des pièces en mouvement, des parties chaudes et de l’échappement.

N’utilisez pas la chargeuse dans des espaces contenant des poussières explosives, des gaz explosifs ou des matières inflammables pouvant se trouver à proximité de l’échappement.

Tous les gaz d’échappement peuvent être mortels. Prévoyez toujours une ventilation.

N’utilisez jamais d’éther ni de fluide de démarrage avec un moteur diesel comportant des bougies de préchauffage.

N’utilisez que des auxiliaires de démarrage approuvés par le fabricant du moteur.

Des fluides qui fuient sous pression peuvent pénétrer la peau et provoquer de graves lésions. Consultez un médecin immédiatement. Portez des lunettes de protection. Utilisez des morceaux de carton pour vérifier toute fuite.

L’acide que contiennent les batteries provoque de graves brûlures; portez des lunettes de protection. En cas de contact avec les yeux, la peau ou les vêtements, rincez à grande eau.

S’il y a eu contact avec les yeux, rincez à fond et consultez un médecin.

Les batteries produisent des gaz inflammables et explosifs.

Tenez à distance toute source d’arcs électriques, d’étincelles et de flammes, ainsi que tout produit de tabac allumé.

Pour effectuer des démarrages avec câbles d’appoint, reliez en dernier le câble négatif au moteur de la chargeuse (jamais à la batterie). Après le démarrage, enlevez d’abord la connexion négative au moteur.

CALENDRIER D’ENTRETIEN (FRENCH)

•

TOUTES LES 100 HEURES

• SILENCIEUX PARE–ÉTINCELLES – Modèles 500 et 700 seulement – Videz la chambre d’étincelles.

• BATTERIE – Vérifiez si la batterie est endommagée; vérifiez les

dispositifs de retenue, les câbles, les connexions ainsi que le niveau d’électrolyte. Ajoutez de l’eau distillée au besoin.

TOUTES LES 250 HEURES (OU TOUS LES 12 MOIS)

• AXES DE LEVIER DE DIRECTION – Lubrifiez (trois points de

graissage) avec une graisse à base de lithium de type universel.

• COURROIE DE TRANSMISSION – Modèles 700 – Vérifiez l’état • • • •

TOUTES LES 10 HEURES (AVANT DE DÉMARRER LA CHARGEUSE)

HYDRAULIQUE, TUYAUX SOUPLES ET TUBULURES – Vérifiez le niveau du fluide. Vérifiez s’il y a dommages et fuites. Réparez ou remplacez au besoin.

TRANSMISSION FINALE (CARTER GARDE–CHAÎNE) – Vérifiez le niveau de liquide à transmission.

COMMANDES HYDRAULIQUES (À PÉDALE OU MANUELLES) ET DIRECTION – Vérifiez le bon fonctionnement. Réglez au besoin. ÉCROUS DE ROUE – Vérifiez si des écrous de roue sont desserrés et, le cas échéant, resserrez suivant les indications du Manuel de l’opérateur et d’entretien.

d’usure et d’endommagement. Réglez ou remplacez au besoin. *Vérifiez toute nouvelle courroie de transmission au bout de 50 heures de service, et réglez–la au besoin.

ARBRE DE TRANSMISSION – Modèles 500 seulement – Lubrifiez le joint universel.

CARTER D’ENGRENAGES D’ENTRAÎNEMENT DU VENTILATEUR – Vérifiez le niveau d’huile.

Vérifiez tous les entraînements par courroie. Vérifiez l’état et la tension des entraînements de pompe hydrostatique, de pompe à eau, d’alternateur et de ventilateur. Réglez ou remplacez au besoin.

BICSt – Vérifiez la commande de dérivation du bras de levage.

TOUTES LES 500 HEURES (OU TOUS LES 12 MOIS)

• HUILE MOTEUR – Vérifiez le niveau, et faites l’appoint au • SYSTÈME HYDRAULIQUE/HYDROSTATIQUE – Remplacez besoin. Évitez de remplir à l’excès. le chapeau de reniflard du réservoir.

• FILTRE À AIR DU MOTEUR – Vérifiez la jauge /ou l’affichage.

TOUTES LES 1000 HEURES (OU TOUS LES 12

N’effectuez d’entretien que si nécessaire.

• CIRCUIT D’AIR DU MOTEUR – Vérifiez s’il y a des fuites et si MOIS) des composants sont endommagés.

• RÉSERVOIR HYDRAULIQUE – Remplacez le fluide • CIRCUIT DE REFROIDISSEMENT DU MOTEUR – hydraulique.

Débarrassez le refroidisseur d’huile et les grillages de tous • TRANSMISSION FINALE (CARTER GARDE-CHAÎNE) – débris.

Modèles 500 et 700 – Vérifiez le niveau de liquide de refroidissement, à froid; ajoutez au besoin un mélange préparé constitué de 53 p. 100 de propylène glycol et de 47 p. 100 d’eau.

85

Remplacez le liquide à transmission.

873 Bobcat Loader Operation & Maintenance Manual

*

ADVERTENCIA (SPANISH) EVITE HERIDAS O LA MUERTE LLEVE LA CARGA EN POSICION BAJA EL NO OBEDECER ESTA ADVERTENCIA PUEDE CAUSAR LADEAMIENTO O VUELCOS O PERDIDAD DE LA CARGA Y DE LA VISIBILIDAD.

PELIGRO (SPANISH)

AVERTISSEMENT (FRENCH)

• MANTENGASE RETIRADO DE ESTA AREA CUANDO

EVITER DES BLESSURES OU LA MORT TENIR LA CHARGE VERS LE BAS. LE NON RESPECT PEUT ENTRAINER UN BASCULEMENT OU UN RENVERSEMENT DE LA MACHINE, UNE PERTE DE LA CHARGE OU DE VISIBILITE.

EVITE LA MUERTE LOS BRAZOS DE ELEVACION ESTAN ELEVADOS, A MENOS QUE ESTEN TRABADOS POW EL TOPE. • EL MOVER EL PIE DEL PEDAL O FALLA DE UNA PIEZA PUEDEN CAUSAR LA CAIDA DE LOS BRAZOS DE ELEVACION.

DANGER (FRENCH) EVITER LA MORT

• EVITER CETTER ZONE LORSQUE LES BRAS DE LEVAGE RELEVÉS NE SONT PAS ASSURÉS PAR DES ARRETS DE BRAS DE LEVAGE. • UNE PEDALE ACTIONNÉE OU UNE PICE DEFECTUEUSE. PEUT PROVOQUER L’ABAISSEMENT DES BRAS DE LEVAGE.

ADVERTENCIA (SPANISH) EVITE LESIONES

• El área del motor tiene piezas giratorias.

• Mantenga la cubierta en su sitio.

• Para más instrucciones, consulte el Manual de servicio.

AVERTISSEMENT (FRENCH) EVITER LA MORT

• Le moteur contient des pièces mobiles.

• Garder le couvercle en place.

• Consulter le Manuel de l’opérateur et d’entretien pour de plus amples renseignements.

PELIGRO (SPANISH) EVITE LA MUERTE

• EL FORZAR EL IMPLEMENTO CONTRA EL SUELO

HACE QUE LA RUEDDAS DELANTERAS SE ELEVEN.

• NUNCA SE META DEBAJO NI ALCANCE NADA DEBA-

JO DE LOS BRAZOS DE ELEVACION O DEL CILINDRO DE ELEVACION SIN QUE ESTE INSLADO UN TOPE APROBADO EN LOS BRAZOS DE ELEVACION.

ADVERTENCIA (SPANISH) EL CILINDRO CONTIENE GAS BAJO ALTA PRESION. EL ABNRIR EL CILINDRO PUEDE SOLTAR LA VARILLA Y CAUSAR HERIDAS O LA MUERTE.

DANGER (FRENCH)

AVERTISSEMENT (FRENCH)

• L’ACCESSOIRE PEUT ETRE APPUYE CONTRE LE

LES VERINS RENFERMENT UN GAZ SOUS PRESSION. NE JAMAIS OUVRIR UN VERIN CAR LA TIGE RISQUE DE S’ECHAPPER BRUTALEMENT ET DE CAUSER DES BLESSURES OU MEME LA MORT.

• NE JAMAIS ALLER SOUS NI METTRE LES MAINS

EVITER LA MORT SOL ET SOULEVER LES ROUES AVANT.

86

SOUS LES BRAS OU LE VERIN DE LEVAGE SANS QU’UN ARRET DE BRAS DE LEVAGE APPROUVE SOIT INSTALLE. 873 Bobcat Loader Operation & Maintenance Manual

PELIGRO (SPANISH) EVITE LA MUERTE

• La desconexión o el aflojamiento de cualquier tubería, manguera, conector, componente hidráulico o la falla de una parte puede ocasionar la caída de los brazos de elevación.

• Manténgase alejado del área cuando los brazos de elevación se encuentren elevados, a menos que estén sostenidos por medio de un dispositivo de soporte para brazos de elevación aprobado. Cámbielo si está dañado.

DANGER (FRENCH)

ADVERTENCIA (SPANISH) El movimiento inesperado del cargador, brazo de levantamiento o implementos causado por el contacto de la cabina con las palancas de dirección puede causar lesiones graves o muerte.

ÉVITEZ LA MORT!

• La déconnexion ou le desserrage de toute canalisation,

de tout tuyau, de tout raccord et de tout composant de circuit hydraulique, ainsi qu’une défaillance de pièce connexe peuvent provoquer la chute des bras de levage.

• Tenez-vous à l’écart de cette région lorsque les bras de levage sont en position levée, à moins qu’ils ne soient soutenus par un dispositif de support de bras de levage de type approuvé. Remplacez si endommagé.

ANTES DE LEVANTAR O BAJAR LA CABINA: • Apague el motor

AVERTISSEMENT (FRENCH) Tout déplacement intempestif de la chargeuse, du bras de levage ou de l’accessoire causé par le contact de la cabine avec les leviers de direction peut causer des blessures graves, voire mortelles.

AVANT DE SOULEVER OU D’ABAISSER LA CABINE : • Couper le moteur

87

873 Bobcat Loader Operation & Maintenance Manual

88

873 Bobcat Loader Operation & Maintenance Manual

SPECIFICATIONS 5.

ADDITIONAL PUBLICATIONS AND TRAINING MATERIALS . . . . . . . . . . . 95 CAPACITIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 CONTROLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91 DRIVE SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 ELECTRICAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 ENGINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91 FLOOR PRESSURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 HYDRAULIC SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 BOBCAT CO. APPROVED ATTACHMENTS & ACCESSORIES . . . . . . . . . 93 PERFORMANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91 SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91 TIRES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92

SPECIFICATIONS

89

873 Bobcat Loader Operation & Maintenance Manual

90

873 Bobcat Loader Operation & Maintenance Manual

•

SKID STEER LOADER SPECIFICATIONS ‘‘C”

84.2 (2139)

Dimensions are given for loader equipped with standard tires and dirt bucket and may vary with other bucket types. All dimensions are shown in inches. Respective metric dimensions are given in millimeters enclosed by parentheses.

• Where applicable, specification conform to SAE or ISO standards and are subject to change without notice.

99°

43° 159.1 (4042) 124.3 (3158) 37.7 (957)

97.3 (2470)

78.0 (1981) ‘‘B” 28°

30°

‘‘A” 8.5 (216)

112.1 (2848)

48.8 (1240)

8.3 (211)

140.3 (3562) 6709140 ‘‘B” 12 – 16.5 TIRES – 60.0” (1524 mm) ‘‘A” 12 – 16.5 TIRES – 73.4” (1864 mm) ‘‘C” 72 in. C/I BUCKET – 74.0” (1879 mm) 31 – 15.5 x 15 TIRES – 79.6” (2022 mm) 31 – 15.5 x 15 TIRES – 64.1” (1628 mm) 72 in. L/P BUCKET – 74.0” (1879 mm) 8.25 x 15 TIRES – 68.3’’ (1736 mm) 8.25 x 15 TIRES – 58.7’’ (1492 mm) 66 in. C/I BUCKET – 68.1” (1731 mm) Changes of structure or weight distribution of the loader can cause changes in control and steering response and can cause failure of the loader parts.

PERFORMANCE Rated Operating Capacity (SAE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2400 lbs. (1089 kg) Tipping Load (SAE Rating) . . . . . . . . . . . . . . . . . . . . .

4600 lbs. (2086 kg) Operating Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6885 lbs. (3123 kg) SAE Breakout Force –Lift . . . . . . . . . . . . . . . . . . . . . .

4800 lbs. (21352 N) –Tilt . . . . . . . . . . . . . . . . . . . . . . .

4700 lbs. (20907 N) Axle Torque . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4900 ft.–lbs. (6644 Nm) Travel Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

0–8.1 MPH (13,0 km/hr.)

CONTROLS Vehicle Steering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Loader Hydraulics Lift and Tilt . . . . . . . . . . . . . . . . . .

Front Auxiliary (Option) . . . . . . . . . . . . . . . . . . . . . .

Secondary Brake . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Parking Brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Direction and Speed controlled by two hand levers.

Controlled by separate foot pedals or optional hand controls.

Proportional Controls Controlled by electrical switch on RH steering lever.

Controlled by electrical switch on LH steering lever.

Hand lever throttle: Key–type starter switch and shutdown.

Glow plug– Rocker Switch operated.

BOSS activated glow plug (If so equipped).

Two independent hydrostatic systems controlled by two hand operated steering levers.

One of the hydrostatic transmissions Mechanical Disc, foot operated pedal.

ENGINE Make/Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Fuel/Cooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Horsepower (SAE Net) . . . . . . . . . . . . . . . . . . . . . . . . .

Maximum Governed RPM . . . . . . . . . . . . . . . . . . . . . . .

Torque @ 1800 RPM (SAE Net) . . . . . . . . . . . . . . . . . . . . . .

Number of Cylinders . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Displacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Bore/Stroke . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Crankcase Ventilation . . . . . . . . . . . . . . . . . . . . . . . . . .

Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Ignition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Deutz/BF4M1011F Turbo–Charged Diesel/Oil 73.0 HP (54 kW) 2350 RPM 176 ft.–lbs. (238 Nm) Four 177.7 cu. in. (2912 cu.cm.)

3.58/4.41 (91.112) Pressure System W/Filter Closed Dry replaceable cartridge w/safety element Diesel–Compression

Rear Auxiliary (Option) . . . . . . . . . . . . . . . . . . . . . . .

Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Starting Aid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Service Brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

91

873 Bobcat Loader Operation & Maintenance Manual

SPECIFICATIONS (Cont’d) HYDRAULIC SYSTEM Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Pump Capacity . . . . . . . . . . . . . . . . . . . . . . . .

System Relief at Quick Couplers . . . . . . . . .

Filters (charge & implement) . . . . . . . . . . . . .

Hydraulic Cylinders . . . . . . . . . . . . . . . . . . . . .

Bore Diameter: Lift Cylinder (2) . . . . . . . . . . . . . . . . . . . . . . .

Tilt Cylinder (2) . . . . . . . . . . . . . . . . . . . . . . .

Rod Diameter: Lift Cylinder (2) . . . . . . . . . . . . . . . . . . . . . . .

Tilt Cylinder (2) . . . . . . . . . . . . . . . . . . . . . . .

Stroke: Lift Cylinder (2) . . . . . . . . . . . . . . . . . . . . . . .

Tilt Cylinder (2) . . . . . . . . . . . . . . . . . . . . . . .

Control Valve . . . . . . . . . . . . . . . . . . . . . . . . . .

Fluid Lines . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Fluid Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Engine Driven, Gear Type 18.0 GPM (68 L/min.) @ 2750 RPM 3000 PSI (20685 kPa) Full flow replaceable, 3 micron synthetic media element Doubleacting 2.75 (69,9) 2.50 (63,5) 1.50 (38,1) 1.25 (31,8) 31.0 (787) 18.0 (458) 3–spool, open center type w/float detent on lift and electrically controlled auxiliary spool.

SAE standard tubes, hoses & fittings Bobcat Fluid (P/N 6563328) if fluid is not available, use 10W–30/10W–40 Class SE motor oil for temperature above 0°F (–18°C) 5W–30 Motor Oil for temperatures below 0°F (–18° C).

Hydraulic Function Time Raise Lift Arms . . . . . . . . . . . . . . . . . . . . . . .

Lower Lift Arms . . . . . . . . . . . . . . . . . . . . . . .

Bucket Dump . . . . . . . . . . . . . . . . . . . . . . . . .

Bucket Rollback . . . . . . . . . . . . . . . . . . . . . .

ELECTRICAL Alternator . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Starter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Instrumentation . . . . . . . . . . . . . . . . . . . . . . . .

5.04 Seconds 4.57 Seconds 2.33 Seconds 1.78 Seconds Belt driven, 50 amp, open 12 volt, 1000 cold cranking amps. @ 0°F. (–18°C); 180 minute reserve capacity 12 volt, Direct Drive; 3.62 HP (2,7 kW) Gauges: Hourmeter, Fuel, Voltmeter, Engine Temperature.

Warning Lights: Engine Temperature, Engine Oil Pressure, Hydraulic Oil

Temperature & Pressure, Hydraulic Filter.

Optional BOSS System Monitors; Engine oil Temperature, Engine Oil Pressure, Hydraulic System Temperature & Pressure, Hydraulic & Air Filters, RPM, Battery Condition, Fuel Level & Machine Hours.

Displays visual warnings & sounds audible alarm. Also controls automatic shutdown function and has diagnostic capability.

DRIVE SYSTEM Main Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Transmission . . . . . . . . . . . . . . . . . . . . . . . . . .

Final Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Hydrostatic 4 wheel drive Infinitely variable tandem hydrostatic piston pumps, driving 2 fully reversing hydrostatic motors #100 HS endless roller chain & sprockets in sealed chaincase with oil lubrication

Total Engine to Wheel Reduction . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Axle Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Wheel Bolts . . . . . . . . . . . . . . . . . . . . . . . . . . .

30.35:1 2.0 (50,8) (8) 9/16”

CAPACITIES Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Engine Crankcase and Cooling System . . . .

Engine Crankcase W/Filter . . . . . . . . . . . . . . .

Hydraulic/Hydro. Reservoir . . . . . . . . . . . . . . .

Hydraulic/Hydro. System . . . . . . . . . . . . . . . . .

Chaincase Reservoir . . . . . . . . . . . . . . . . . . . . .

25 gals. (94 L) 16 qts. (9,5 L) 10.0 qts. (15,1 L) 4 gals. (15,2 L) 10 gals. (38 L) 11 gals. (41,6 L)

TIRES Standard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Flotation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Narrow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Recommended Pressure . . . . . . . . . . . . . .

FLOOR PRESSURE 12–16.5 Bobcat Tires – Max. . . . . . . . . . . . .

31–15.5 x 15 Flot. Tires Max. . . . . . . . . . .

8.25 – 15 Narrow Tires – Max. . . . . . . . . . .

12–16.5, 10 ply rating 31–15.5 x 15,8 Ply Rating 8.25 – 15, 6 Ply Rating Inflate tires to MAXIMUM pressure shown on the side wall of the tire. DO NOT mix brands of tires used on the same loader.

W/Rated Load W/Rated Load W/Rated Load

92

52 PSI (359 kPa) 49 PSI (338 kPa) 79 PSI (545 kPa)

873 Bobcat Loader Operation & Maintenance Manual

BOBCAT COMPANY APPROVED ATTACHMENTS & ACCESSORIES These and other attachments are approved for use on this model Bobcat loader. Do not use unapproved attachments.

Attachments not manufactured by Bobcat Company may not be approved.

The versatile Bobcat loader quickly turns into a multi–job machine with a tight–fit attachment hook–up . . . from bucket to grapple to pallet fork to backhoe and a variety or other attachments.

See your Bobcat dealer for more details on the these and other attachments and field accessories.

Increase the versatility of your Bobcat Loader with a variety of bucket styles and sizes.

BUCKETS AVAILABLE Many bucket styles, widths and different capacities are available for a variety of different applications. They include Construction & Industrial, Utility, Fertilizer and Snow, to name a few. See your Bobcat dealer for the correct bucket for your Bobcat loader and application.

ATTACHMENTS Vibratory Roller

Angle Broom

Stump Grinder

Sweeper

Use it to sweep Ideal for flatwork, trenching driveways,sidewalks, and asphalt patchwork parking lot & countless other Sweeps and collects debris with one attachment. contractors. applications.

8709 Backhoe Econo–Grader

Great for high production digging.

Box Scraper

Great for removing stumps from hard to access areas.

Grader

Use it as an economical, but effective Designed for use by landscaping, grader OR a box blade by utilizing asphalt, curb & gutter & flat concrete work. locking end plates.

Landscape Rake Hydraulic Breaker

Break up lumpy soil, pick up rocks. Break up concrete quickly and easily.

APPLICATIONS KIT WHICH INCLUDES A 1/2 INCH LEXAN Great for removing stumps from hard Ground preparation,, for seeding, SPECIAL FRONT DOOR WITH 1/4 INCH TOP AND REAR WINDOWS MUST BE USED WHEN OPERATING THE BOB–TACH MOUNTED HYDRAULIC sodding, leveling.

BREAKER. to access areas.

Longwood Grapple Brushcat Rotary Cutter Scarifier Power Rake

For handling logs.

SPECIAL APPLICATIONS KIT WHICH INCLUDES A 1/2 INCH LEXAN FRONT DOOR WITH 1/4 INCH TOP AND REAR WINDOWS MUST BE USED WHEN OPERATING THE LONGWOOD GRAPPLE.

Tiller

Prepares hard–packed ground for digging or landscaping.

Utility Fork (Grapple Available)

Separate rocks & debris, grade, level, prepare for Great for clearing brush, landscaping. saplings and grass.

Bale Handler Pallet Fork

Great for breaking up Ideal for handling bundled clumps, mixing compost, material, loose straw, and tilling. manure.

Ideal for all kinds of farm chores and fertilizer handling.

93

Manage large round bales easily with the Bale Handler.

873 Bobcat Loader Operation & Maintenance Manual

BOBCAT COMPANY APPROVED ATTACHMENTS & ACCESSORIES (Cont’d) These and other attachments are approved for use on this model Bobcat loader. Do not use unapproved attachments.

Attachments not manufactured by Bobcat Company may not be approved.

See your Bobcat dealer for more details on the these and other attachments and field accessories.

ATTACHMENTS (Cont’d) Auger

Rear Stabilizer

Snow Blower

Angle Blade

(Use with backhoe & transplanter)

Remove heavy snow from Dig 6”–36” holes with ease Increase your backhoe Clear snow from driveways, the surface, before it’s and accuracy. performance and versatility. sidewalks, etc. compacted.

Rake Tree Transplanter Trencher

Dig and load trees for transplanting.

Tracks

Versatile trenching ability for utility lines, etc.

The Rake is a versatile landscape machine.

You’ll get better performance in sand, snow and mud.

94

873 Bobcat Loader Operation & Maintenance Manual

ADDITIONAL PUBLICATIONS and TRAINING MATERIALS The following publications and training materials are also available for your Bobcat Loader. You can order them from your Bobcat dealer.

For the latest information on Bobcat products and the Bobcat Company, visit our website at www.bobcat.com

OPERATOR’S HANDBOOK 6708021–Foot Pedals 6708158–Hand Controls –gives basic operation instruction and safety warnings.

PARTS MICROFICHE OPERATION & MAINTENANCE SERVICE MANUAL MANUAL 6900382 6900791 –complete instruction on the correct operation and the routine maintenance of the BOBCAT loader.

–Up–to–date PARTS information is also available. See your BOBCAT dealer.

–complete maintenance overhaul instructions for BOBCAT loader.

and your

SKID STEER LOADER SERVICE SAFETY TRAINING COURSE 6900641 SKID STEER LOADER OPERATOR TRAINING COURSE 6722720 –Introduces operator to step–by–step basics of Skid–Steer loader operation.

Also available in Spanish P/N 6724036.

–Introduces Service Technicians to step–by–step basics of proper and safe skid–steer loader maintenance and servicing procedures.

OPERATION SAFETY VIDEO 6724793

SAFETY MANUAL 6556500

Skid–Steer Loader

EQUIPMENTMANUFACTURERS INSTITUTE 10S.RIVERSIDEPLAZACHICAGO,ILLINOIS60606–37100

–provides basic safety instructions.

–provides basic safety procedures and warnings for your BOBCAT loader. Also available in Spanish P/N 6724451.

95

873 Bobcat Loader Operation & Maintenance Manual

96

873 Bobcat Loader Operation & Maintenance Manual

WARRANTY Bobcat Loaders Bobcat Company warrants to its authorized dealers and authorized dealers of Bobcat Equipment Ltd., who in turn warrant to the original buyer (owner), that each new Bobcat loader will be free from proven defects in material and workmanship for twelve months after delivery to the original buyer (owner).

During the warranty period, the authorized Bobcat dealer shall repair or replace, at its option, without charge for parts and labor, any part of the Bobcat product which fails because of defects in material or workmanship. The owner shall provide the authorized Bobcat dealer with prompt written notice of the defect and allow reasonable time for replacement or repair. Bobcat Company may, at its option, request failed parts to be returned to the factory. Travel time of mechanics and transportation of the Bobcat product to the authorized Bobcat dealer for warranty work are the responsibility of the owner.

The warranty does not apply to tires or other trade accessories not manufactured

by Bobcat Company. The owner shall rely solely on the warranty, if any, of the respective manufacturers thereof. The warranty does not cover replacement of scheduled service items such as oil, filters, tune–up parts, and other high–wear items. The warranty does not cover damages resulting from abuse, accidents, alterations, use of the Bobcat product with any bucket or attachment not approved

by Bobcat Company, air flow obstructions, or failure to maintain or use the Bobcat product according to the instructions applicable to it.

THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES (EXCEPT THOSE OF TITLE), EXPRESSED OR IMPLIED, AND THERE ARE NO WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL BOBCAT COMPANY OR THE AUTHORIZED BOBCAT DEALER BE LIABLE FOR DOWNTIME EXPENSES, LOSS OF MACHINE USE OR OTHER INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES.

6570162 (5–00)

Printed in U.S.A.