Ditch Witch MX15 Mini Excavator Operator’s Manual – PDF DOWNLOAD

MX15

Operator’s Manual

Issue 1.0

054- 109

MX15 Operator’s Manual

Foreword - 1

Foreword 11

MX15 Operator’s Manual Issue number 1.0/OM-4/03 Part number 054-109 Copyright 2003

by The Charles Machine Works, Inc.

, Ditch Witch, AutoCrowd, Modularmatic, Jet Trac, Roto Witch, Subsite, Fluid Miser, Sidekick, Perma-Soil, Power Pipe, Super Witch, Super Witch II, Pierce Airrow, and The Underground are registered trademarks of The Charles Machine Works, Inc. CMW and The Underground Authority Worldwide are pending trademarks of The Charles Machine Works, Inc.

Your Machine Serial Numbers and Dealer Machine serial no.

Engine serial no.

Dealer name Address

Service personnel Phone/fax

MX15 Operator’s Manual

Foreword - 2

This manual provides rules and guidelines which will help you use this machine safely and effectively. The precautions in this manual must be followed at all times when performing operation and maintenance.

Most accidents are caused by the failure to follow fundamental safety rules for the operation and maintenance of machines. Accidents can be prevented by knowing beforehand conditions that may cause a hazard when performing operation and maintenance.

WARNING Before beginning operation or maintenance, operators and maintenance personnel must always observe the following points.

•

Read this manual thoroughly and understand its contents fully.

•

Read the safety messages and safety labels given in this manual carefully so that they should be understood fully.

•

Keep this manual at the storage location for the operator’s manual given below so that all personnel involved in working on the machine can consult it periodically.

•

In case this manual should be lost or damaged, immediately contact The Charles Machine Works, Inc. or your Ditch Witch dealer to obtain a new copy.

•

When you sell the machine, make sure that this manual should be provided to the new owner together with the machine.

•

In this manual, measurements are expressed in international standard units (SI). For the reference purpose, weight units used in the past are also displayed in { }.

Storage location for the operator’s manual: pocket at rear of operator's seat

MX15 Operator’s Manual

Foreword - 3

Safety Information

Safety Information To enable you to use this machine safely, safety precautions and labels are given in this manual and affixed to the machine to give explanations of situations involving potential hazards and of the methods of avoiding such situations.

Signal Words The following signal words are used to inform you that there is a potential hazardous situation that may lead to personal injury or damage.

In this manual and on machine labels, the following signal words are used to express the potential level of hazard.

Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. This word is used also to alert against unsafe practices that may cause property damage.

Example of Safety Message Using Signal Word

WARNING When standing up from the operator’s seat, always place the safety lock lever in the LOCK position.

If you accidentally touch the control levers when they are not locked, this may cause a serious injury or death.

Other Signal Words In addition to the above, the following signal words are used to indicate precautions that should be followed to protect the machine or to give information that is useful to know.

This word is used for precautions that must be taken to avoid actions which could shorten the life of the machine.

This word is used for information that is useful to know.

Foreword - 4

MX15 Operator’s Manual Safety Information

Safety Labels Safety labels are affixed to the machine to inform the operator or maintenance worker on the spot when carrying out operation or maintenance of the machine that may involve hazard.

This machine uses “safety labels using words” and “safety labels using pictograms” to indicate safety procedures.

Example of Safety Label Using Words

Example of Safety Label Using Pictogram Safety pictograms use a picture to express a level of hazardous condition equivalent to the signal word.

These safety pictograms use pictures in order to let the operator or maintenance worker understand the level and type of hazardous condition at all times.

Safety pictograms show the type of hazardous condition at the top or left side, and the method of avoiding the hazardous condition at the bottom or right side. In addition, the type of hazardous condition is displayed inside a triangle and the method of avoiding the hazardous condition is shown inside a circle.

MX15 Operator’s Manual

Foreword - 5

Safety Information The Charles Machine Works, Inc. cannot predict every circumstance that might involve a potential hazard in operation and maintenance. Therefore, the safety messages in this manual and on the machine may not include all possible safety precautions.

If any procedures or actions not specifically recommended or allowed in this manual are used, it is your responsibility to take the necessary steps to ensure safety.

In no event should you engage in prohibited uses or actions described in this manual.

The explanations, values, and illustrations in this manual were prepared based on the latest information available at that time. Continuing improvements in the design of this machine can lead to changes in detail which may not be reflected in this manual. Consult The Charles Machine Works, Inc. or your Ditch Witch dealer for the latest available information for your machine or for questions regarding information in this manual.

The numbers in circles in the illustrations correspond to the numbers in ( ) in the text.

Foreword - 6

MX15 Operator’s Manual Introduction

Introduction This Ditch Witch machine is designed to be used mainly for the following work: •

Digging work

•

Leveling work

•

Ditching work

•

Loading work

•

Demolition work

See “Work Possible Using Compact Hydraulic Excavator” on page 108 for further details.

Directions of Machine

In this manual, the terms front, rear, left, and right refer to the travel direction as seen from the operator's seat when the operator's seat is facing the front and the sprocket is at the rear of the machine.

MX15 Operator’s Manual

Foreword - 7

Product Information

Product Information When requesting service or ordering replacement parts, please inform your Ditch Witch dealer of the following items.

Machine Serial Number Plate and Its Location At the right side of the boom swing mount

Engine Serial Number Plate and Its Location On the upper side of the engine cylinder head cover

Foreword - 8

MX15 Operator’s Manual Product Information

Emission Control Information Label and Its Location Inside surface of the left rear leg of the operator’s seat stand

Service Meter Location On top of the machine monitor.

MX15 Operator’s Manual

Foreword - 9

Contents

Contents Foreword

1

part number, revision level, and publication date of this manual, factory contact information, general safety information, and locations of serial number plates

Safety

11

machine safety alerts and information, safe operation procedures, and safe maintenance procedures

Operation

51

machine controls, operating instructions, transportation instructions, cold weather operation instructions, long-term storage procedures, and troubleshooting

Maintenance

141

general maintenance procedures, recommended lubricants and coolants, and maintenance intervals and procedures

Specifications

189

machine specifications including weights, measurements, power ratings, and working ranges

Attachments and Options

191

general attachment information, available options and attachments, and attachment installation preparation

Support the warranty policy for this machine, and procedures for obtaining warranty consideration and training

209

Foreword - 10

MX15 Operator’s Manual Contents

MX15 Operator’s Manual

Safety - 11

Chapter Contents

Safety 22

WARNING Please read and make sure that you fully understand the precautions described in this manual and the safety labels on the machine. When operating or servicing the machine, always follow these precautions strictly.

Chapter Contents Safety Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 •

Location of Safety Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

•

Safety Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 •

Safety Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

•

If Abnormalities Are Found . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

•

Working Wear and Personal Protective Items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

•

Fire Extinguisher and First Aid Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

•

Safety Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

•

Keep Machine Clean . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

•

Keep Operator's Compartment Clean . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

•

Leaving Operator's Seat with Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

•

Handrails and Steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

•

Mounting and Dismounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

•

No Persons on Attachments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

•

Do Not Get Caught in Articulated Portion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

•

Burn Prevention . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

•

Fire Prevention and Explosion Prevention . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

•

Action if Fire Occurs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

•

Windshield Washer Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

•

Falling Objects, Flying Objects and Intruding Objects Prevention . . . . . . . . . . . . . . . . . . . . . 25

•

Attachment Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

•

Attachment Combinations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

Safety - 12

MX15 Operator’s Manual Chapter Contents

•

Cab Window Glasses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

•

Unauthorized Modifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

•

Safety at Jobsite . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

•

Working on Loose Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

•

Distance to High Voltage Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

•

Ensure Good Visibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

•

Ventilation for Enclosed Area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

•

Signalperson's Signal and Signs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

•

Asbestos Dust Hazard Prevention . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Safe Machine Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 •

Starting Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

•

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

•

Transportation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

•

Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

•

Towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

•

Lifting Objects with Bucket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

MX15 Operator’s Manual

Safety - 13

Chapter Contents

Safe Maintenance Information . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 •

Warning Tag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

•

Keep Work Place Clean and Tidy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

•

Appoint Leader when Working with Others . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43

•

Stop Engine Before Carrying Out Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44

•

Two Workers for Maintenance when Engine Is Running . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

•

Proper Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

•

Personnel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45

•

Attachments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

•

Work Under the Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

•

Noise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

•

When Using Hammer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

•

Welding Works . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

•

Removing Battery Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

•

Safety First when Using High-Pressure Grease to Adjust Track Tension . . . . . . . . . . . . . . . 48

•

Do Not Disassemble Recoil Springs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

•

Safety Rules for High-Pressure Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

•

Safety Handling High-Pressure Hoses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

•

Waste Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

•

Air Conditioner Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

•

Compressed Air . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

•

Periodic Replacement of Safety Critical Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Safety - 14

MX15 Operator’s Manual Safety Labels

Safety Labels The following warning signs and safety labels are used on this machine.

•

Be sure that you fully understand the correct position and content of labels.

•

To ensure that the content of labels can be read properly, be sure that they are in the correct place and always keep them clean. When cleaning them, do not use organic solvents or gasoline. These may cause the labels to peel off.

•

There are also other labels in addition to the warning signs and safety labels. Handle those labels in the same way.

•

If the labels are damaged, lost, or cannot be read properly, replace them with new ones. For details of the part numbers for the labels, see this manual or the actual label, and place an order with your Ditch Witch dealer.

Location of Safety Labels

v

MX15 Operator’s Manual

Safety - 15

Safety Labels

Safety Labels (1) Precautions for operation, inspection and maintenance (p/n 454-409)

(2) Precautions for operation (p/n 454-621)

(3 )Precautions for leaving the operator’s seat (p/n 454-411)

(4 )Precautions for minimum variable gauge (p/n 454-472)

Safety - 16

MX15 Operator’s Manual Safety Labels

(5) Precautions for operating pattern (p/n 454-424)

(6) Precautions for high-temperature hydraulic oil (p/n 454-410)

(7) Precautions for high-temperature coolant (p/n 454-429)

(8) Precautions for handling electric wires (p/n 454-422)

MX15 Operator’s Manual

Safety - 17

Safety Labels (9) Precautions for safety lock operation (p/n 454-786)

(10) Precautions for check and adjust track tension (p/n 454-412)

(11) Precautions for opening engine hood (p/n 454-415)

(12) Prohibited to enter range of swing (p/n 454-447 & 454-448)

(13) Precautions when handling TOPS

Safety - 18

MX15 Operator’s Manual Safety Information

Safety Information Safety Rules •

Only trained and authorized personnel can operate and maintain the machine.

•

Follow all safety rules, precautions and instructions when operating or performing maintenance on the machine.

•

If you are under the influence of alcohol or medication, your ability to safely operate or repair your machine may be severely impaired putting yourself and everyone else on your jobsite in danger.

•

When working with another operator or with a person on worksite traffic duty, be sure that all personnel understand all hand signals that are to be used.

If Abnormalities Are Found If you find any abnormality in the machine during operation or maintenance (noise, vibration, smell, incorrect gauges, smoke, oil leakage, etc., or any abnormal display on the warning devices or monitor), report to the person in charge and have the necessary action taken. Do not operate the machine until the abnormality has been corrected.

Working Wear and Personal Protective Items •

Do not wear loose clothing and accessories. There is a hazard that they may catch on control levers or other protruding parts.

•

If you have long hair and it hangs out from your hard hat, there is a hazard that it may get caught up in the machine, so tie your hair up and be careful not to let it get caught.

•

Always wear a hard hat and safety shoes. If the nature of the work requires it, wear safety glasses, mask, gloves, ear plugs, and safety belt when operating or maintaining the machine.

•

Check that all protective equipment functions properly before using it.

MX15 Operator’s Manual

Safety - 19

Safety Information

Fire Extinguisher and First Aid Kit Always follow the precautions below to prepare for action if any injury or fire should occur.

•

Be sure that fire extinguishers have been provided and read the labels to ensure that you know how to use them in emergencies.

•

Carry out periodic inspection and maintenance to ensure that the fire extinguisher can always be used.

•

Provide a first aid kit at the storage point. Carry out periodic checks and add to the contents if necessary.

Safety Equipment •

Be sure that all guards and covers are in their proper position. Have guards and covers repaired immediately if they are damaged.

•

Understand the method of use of safety features and use them properly.

•

Never remove any safety features. Always keep them in good operating condition.

Keep Machine Clean •

If water gets into the electrical system, there is a hazard that it will cause malfunctions or misoperation. Do not use water or steam to wash the electrical system (sensors, connectors).

•

If inspection and maintenance is carried out when the machine is still dirty with mud or oil, there is a hazard that you will slip and fall, or that dirt or mud will get into your eyes. Always keep the machine clean.

Safety - 20

MX15 Operator’s Manual Safety Information

Keep Operator’s Compartment Clean •

When entering the operator's compartment, always remove all mud and oil from the soles of your shoes. If you operate the pedal with mud or oil affixed to your shoes, your foot may slip and this may cause a serious accident.

•

Do not leave parts or tools lying around the operator's compartment.

•

Do not stick suction pads to the window glass. Suction pads act as a lens and may cause fire.

•

Do not use cellular telephones inside the operator's compartment when driving or operating the machine.

•

Never bring any dangerous objects such as flammable or explosive items into the operator's compartment.

Leaving Operator’s Seat with Lock •

•

Before standing up from the operator's seat (such as when opening or closing the front window, installing or removing the bottom window, or adjusting the operator's seat), always lower the attachment completely to the ground, set safety lock lever (1) securely to the LOCK position, then stop the engine. If you accidentally touch the levers when they are not locked, there is a hazard that the machine may suddenly move and cause serious injury or property damage.

When leaving the machine, always lower the attachment completely to the ground, set safety lock lever (1) securely to the LOCK position, then stop the engine. Use the key to lock all the equipment. Always remove the key, take it with you, and keep it in a specified place.

Lock Free

MX15 Operator’s Manual

Safety - 21

Safety Information

Handrails and Steps To prevent personal injury caused by slipping or falling off the machine, always do as follows.

•

Use the handrails and steps marked by arrows in the diagram on the right when getting on or off the machine.

•

To ensure safety, always face the machine and maintain three-point contact (both feet and one hand, or both hands and one foot) with the handrails and steps (including the track) to ensure that you support yourself.

•

Do not grip the control levers when getting on or off the machine.

•

Never climb on the engine hood or covers where there are no non-slip pads.

•

Before getting on or off the machine, check the handrails and steps (including the track). If there is any oil, grease, or mud on the handrails or steps (including the track), wipe it off immediately. Always keep these parts clean. Repair any damage and tighten any loose bolts.

•

Do not get on or off the machine while holding tools in your hand.

Crushing or Cutting Prevention Do not put your hand, arm or any other part of your body between movable parts such as the backhoe and cylinders, or between the machine and backhoe. When the backhoe is operated, the clearance will change and this may lead to serious damage or personal injury.

Mounting and Dismounting •

Never jump on or off the machine. Never get on or off a moving machine.

•

If the machine starts to move when there is no operator on the machine, do not jump on to the machine and try to stop it.

Safety - 22

MX15 Operator’s Manual Safety Information

No Persons on Attachments Never let anyone ride on the backhoe or other attachments. There is a hazard of falling and suffering serious injury.

Burn Prevention Hot Coolant •

To prevent burns from hot water or steam spurting out when checking or draining the coolant, wait for the water to cool to a temperature where it is possible to touch the radiator cap by hand before starting the operation. Even when the coolant has cooled down, loosen the cap slowly to relieve the pressure inside the radiator before removing the cap.

Hot Oil •

To prevent burns from hot oil spurting out when checking or draining the oil, wait for the oil to cool to at temperature where it is possible to touch the cap or plug by hand before starting the operation. Even when the oil has cooled down, loosen the cap or plug slowly to relieve the internal pressure before removing the cap or plug.

MX15 Operator’s Manual

Safety - 23

Safety Information

Fire Prevention and Explosion Prevention Fire Caused by Fuel or Oil Fuel, oil, coolant, and window washer liquid are particularly flammable and can be hazardous. To prevent fire, always observe the following: •

Do not smoke or use any flame near fuel or oil.

•

Stop the engine before refueling.

•

Do not leave the machine while adding fuel or oil.

•

Tighten all fuel and oil caps securely.

•

Do not spill fuel on overheated surfaces or on parts of the electrical system.

•

Use well-ventilated areas for adding or storing oil and fuel.

•

Keep oil and fuel in the determined place and do not allow unauthorized persons to enter.

•

After adding fuel or oil, wipe up any spilled fuel or oil.

•

When carrying out grinding or welding work on the chassis, move any flammable materials to a safe place before starting.

•

When washing parts with oil, use a non-flammable oil. Diesel oil and gasoline may catch fire, so do not use them.

•

Put greasy rags and other flammable materials into a safe container to maintain safety at the work place.

•

Do not weld or use a cutting torch to cut any pipes or tubes that contain flammable liquids.

Fire Caused by Accumulation of Flammable Material Remove any dry leaves, chips, pieces of paper, dust, or any other flammable materials accumulated or affixed around the engine, exhaust manifold, muffler, or battery, or inside the undercovers.

Safety - 24

MX15 Operator’s Manual Safety Information

Fire Coming from Electric Wiring Short circuits in the electrical system can cause fire.

•

Always keep electric wiring connections clean and securely tightened.

•

Check the wiring every day for looseness or damage. Tighten any loose connectors or wiring clamps.

Repair or replace any damaged wiring.

Fire Coming from Hydraulic Line Check that all the hose and tube clamps, guards, and cushions are securely fixed in position. If they are loose, they may vibrate during operation and rub against other parts. This may lead to damage to the hoses, and cause high-pressure oil to spurt out, leading to fire damage or serious injury.

Explosion Caused by Lighting Equipment •

When checking fuel, oil, battery electrolyte, window washer fluid, or coolant, always use lighting with anti-explosion specifications. If such lighting equipment is not used, there is danger of explosion that may cause serious injury.

•

When taking the electrical power for the lighting from the machine itself, follow the instructions in this manual.

Action if Fire Occurs If a fire occurs, escape from the machine as follows.

•

Turn the start switch OFF to stop the engine.

•

Use the handrails and steps to get off the machine.

Windshield Washer Fluid Use an ethyl alcohol base washer liquid. Methyl alcohol base washer liquid may irritate your eyes, so do not use it.

MX15 Operator’s Manual

Safety - 25

Safety Information

Falling Objects, Flying Objects and Intruding Objects Prevention On jobsites where there is a hazard that falling objects, flying objects, or intruding objects may hit or enter the operator’s cab, consider the operating conditions and install the necessary guards to protect the operator.

•

When carrying out demolition or breaker operations, install a front guard and use a laminated coating sheet on the front glass.

•

When working in mines or quarries where there is a hazard of falling rock, install FOPS (Falling Objects Protective Structure) and a front guard, and use a laminated coating sheet on the front glass.

•

When carrying out the above operations, always close the front window. In addition, always ensure that bystanders are a safe distance away and are not in hazard from falling or flying objects.

•

The above recommendations assume that the conditions are for standard operations, but it may be necessary to add additional guards according to the operating conditions on the jobsite. Always contact your Ditch Witch dealer for advice.

Attachment Installation •

When installing optional parts or attachments, there may be problems with safety or legal restrictions.

Therefore contact your Ditch Witch dealer for advice.

•

Any injuries, accidents, or product failures resulting from the use of unauthorized attachments or parts will not be the responsibility of The Charles Machine Works, Inc.

•

When installing and using optional attachments, read the instruction manual for the attachment, and the general information related to attachments in this manual.

Attachment Combinations Depending on the type or combination of attachments, there is a hazard that the attachments may hit the cab or other parts of the machine. Before using unfamiliar attachments, check if there is any hazard of interference, and operate with caution.

Safety - 26

MX15 Operator’s Manual Safety Information

Cab Window Glasses If the cab glass on the backhoe side is broken, there is a hazard that the backhoe may contact the operator’s body directly. Stop operation immediately and replace the glass.

Unauthorized Modifications Any modification made without authorization from The Charles Machine Works, Inc. can create hazards.

Before making a modification, consult your Ditch Witch dealer.

•

The Charles Machine Works, Inc. will not be responsible for any injuries, accidents, product failures or other property damages resulting from modifications made without authorization from The Charles Machine Works, Inc.

Safety at Jobsite Before starting operations, thoroughly check the area for any unusual conditions that could be dangerous.

•

When carrying out operations near combustible materials such as thatched roofs, dry leaves or dry grass, there is a hazard of fire, so be careful when operating.

•

Check the terrain and condition of the ground at the worksite, and determine the safest method of operation. Do not carry out operations at places where there is a hazard of landslides or falling rocks.

•

If water lines, gas lines, or high-voltage electrical lines may be buried under the worksite, contact each utility and identify their locations. Be careful not to sever or damage any of these lines.

•

Take action to prevent unauthorized people from approaching the jobsite.

•

When traveling or operating in shallow water or on soft ground, check the shape and condition of the bedrock, and the depth and speed of flow of the water before starting operations.

Working on Loose Ground •

Avoid traveling or operating your machine too close to the edge of cliffs, overhangs, and deep ditches.

The ground may be weak in such areas. If the ground should collapse under the weight or vibration of the machine, there is a hazard that the machine may fall or tip over. Remember that the soil after heavy rain or blasting or after earthquakes is weak in these areas.

•

When working on embankments or near excavated ditches, there is a hazard that the weight and vibration of the machine will cause the soil to collapse. Before starting operations, take steps to ensure that the ground is safe and to prevent the machine from rolling over or falling.

MX15 Operator’s Manual

Safety - 27

Safety Information

Distance to High Voltage Cables Do not travel or operate the machine near electric cables. There is a hazard of electric shock, which may cause serious injury or property damage. On jobsites where the machine may go close to electric cables, always do as follows.

•

Before starting work near electric cables, inform the local power company of the work to be performed, and ask them to take the necessary action.

•

Even going close to high-voltage cables can cause electric shock, which may cause serious burns or even death. Always maintain a safe distance (see the table on the right) between the machine and the electric cable. Check with the local power company about safe operating procedure before starting operations.

•

•

To prepare for any possible emergencies, wear rubber shoes and gloves. Lay a rubber sheet on top of the seat, and be careful not to touch the chassis with any exposed part of your body.

Use a signalperson to give warning if the machine approaches too close to the electric cables.

Voltage of Cables

Safety Distance

100 V - 200 V

Over 2 m (7’)

6,600 V

Over 2 m (7’)

22,000 V

Over 3 m (10’)

66,000 V

Over 4 m (14’)

154,000 V

Over 5 m (17’)

187,000 V

Over 6 m (20’)

275,000 V

Over 7 m (23’)

500,000 V

Over 11 m (36’)

•

When carrying out operations near high voltage cables, do not let anyone come close to the machine.

•

If the machine should come too close or touch the electric cable, to prevent electric shock, the operator should not leave the operator's compartment until it has been confirmed that the electricity has been shut off. Also, do not let anyone come close to the machine.

Ensure Good Visibility Check for any persons or obstacles in the area around the machine and check the conditions of the jobsite to ensure that operations and travel can be carried out safely. Always do as follows.

•

Position a signalperson if there are areas at the rear of the machine where the visibility is not good.

•

When working in dark places, turn on the working lamp and front lamps installed to the machine, and set up additional lighting in the work area if necessary.

•

Stop operations if the visibility is poor, such as in mist, snow, rain, or dust.

Safety - 28

MX15 Operator’s Manual Safety Information

Ventilation for Enclosed Area Exhaust fumes from the engine can kill.

•

If it is necessary to start the engine within an enclosed area, or when handling fuel, flushing oil, or paint, open the doors and windows to ensure that adequate ventilation is provided to prevent gas poisoning.

Signalperson’s Signal and Signs •

Set up signs to inform of road shoulders and soft ground. If the visibility is not good, position a signalperson if necessary. Operators should pay careful attention to the signs and follow the instructions from the signalperson.

•

Only one signalperson should give signals.

•

Make sure that all workers understand the meaning of all signals and signs before starting work.

Asbestos Dust Hazard Prevention Asbestos dust in the air can cause lung cancer if it is inhaled. There is danger of inhaling asbestos when working on jobsites handling demolition work or work handling industrial waste. Always observe the following.

•

Spray water to keep down the dust when cleaning.

Do not use compressed air for cleaning.

•

If there is danger that there may be asbestos dust in the air, always operate the machine from an upwind position. All workers should use an approved respirator.

•

Do not allow other persons to approach during the operation.

•

Always observe the rules and regulations for the work site and environmental standards.

This machine does not use asbestos, but there is a danger that imitation parts may contain asbestos, so always use genuine Ditch Witch parts.

MX15 Operator’s Manual

Safety - 29

Safe Machine Operation

Safe Machine Operation Starting Engine If there is a warning tag hanging from the attachment control lever, do not start the engine or touch the levers.

Checks Before Starting Engine Carry out the following checks before starting the engine at the beginning of the day’s work.

•

Remove all dirt from the surface of the window glass to ensure a good view.

•

Remove all dirt from the surface of the lens of the working lamps, and check that they light up correctly.

•

Check the coolant level, fuel level, and oil level in engine oil pan, check for clogging of the air cleaner, and check for damage to the electric wiring.

•

Adjust the operator's seat to a position where it is easy to carry out operations, and check that there is no damage or wear to the seat belt or mounting clamps.

•

Check that the gauges work properly, check the angle of the lights and working lamps, and check that the control levers are all at the neutral position.

•

Before starting the engine, make sure that the safety lock lever is in the LOCK position.

•

Check that there are no persons or obstacles above, below, or in the area around the machine.

Safety - 30

MX15 Operator’s Manual Safe Machine Operation

Safety Rules for Starting Engine •

When starting the engine, sound the horn as a warning.

•

Start and operate the machine only while seated.

•

Do not allow anyone apart from the operator to ride on the machine.

•

Do not short circuit the starting motor circuit to start the engine. Short circuit can cause fire.

Starting Engine in Cold Weather •

Carry out the warm-up operation thoroughly. If the machine is not thoroughly warmed up before the control levers are operated, the reaction of the machine will be slow, and this may lead to unexpected accidents.

•

If the battery electrolyte is frozen, do not charge the battery or start the engine with a different power source. There is a hazard that this will ignite the battery and cause the battery to explode.

Before charging or starting the engine with a different power source, melt the battery electrolyte and check that there is no leakage of electrolyte before starting.

Operation Checks Before Operation When carrying out the checks, move the machine to a wide area where there are no obstructions, and operate slowly. Do not allow anyone near the machine.

•

Always fasten your seat belt.

•

Check that the movement of the machine matches the display on the control pattern card. If it does not match, replace it immediately with the correct control pattern card.

•

Check the operation of the attachment, travel system and swing system.

•

Check for any abnormality in the sound of the machine, vibration, heat, smell, or gauges; check also that there is no leakage of oil or fuel.

•

If any abnormality is found, carry out repairs immediately.

MX15 Operator’s Manual Safe Machine Operation Safety Rules for Changing Machine Directions •

Before traveling, position the upper structure so that the sprocket is at the rear of the operator's cab.

If the sprocket is at the front of the operator's cab, the machine makes a movement reverse to the control lever movement (for example, forward becomes reverse, and left becomes right). Be careful to avoid such a reverse movement of the machine.

•

Before traveling, check again that there is no one in the surrounding area, and that there are no obstacles.

•

Before traveling, sound the horn to warn people in the area.

•

Always operate the machine only when seated.

•

Do not allow anyone apart from the operator to ride on the machine.

•

Always fasten your seat belt.

•

If there is an area to the rear of the machine that cannot be seen, position a signalperson. Take special care not to hit other machines or people when turning or swinging the machine.

•

Always lock the door and windows of the operator's compartment in position (open or closed).

•

On jobsites where there is a hazard of flying objects or of objects entering the operator's compartment, check that the door and windows are securely closed.

Always be sure to carry out the above precautions even when the machine is equipped with mirrors.

Safety - 31

Safety - 32

MX15 Operator’s Manual Safe Machine Operation

Safety Rules for Traveling •

It is dangerous to drive too fast, or to start suddenly, stop suddenly, or to turn sharply.

•

When traveling on level ground, keep the attachment at a height of 40-50 cm (1.6-2.0”) from the ground.

•

When traveling on rough ground, travel at low speed and do not operate the steering suddenly.

There is danger that the machine may turn over.

The attachment may hit the ground surface and cause the machine to lose its balance, or may damage the machine or structures in the area.

•

When traveling on rough ground or steep slopes, if the machine is equipped with auto-deceleration, always turn auto-deceleration switch OFF (cancel).

If the auto-deceleration is ON, the engine speed may rise and the travel speed may suddenly increase.

•

Avoid traveling over obstacles when possible. If the machine has to travel over an obstacle, keep the attachment close to the ground and travel at low speed. Never travel over obstacles which make the machine tilt strongly to one side.

•

When traveling or carrying out operations, always keep a safe distance from people, structures, or other machines to avoid coming into contact with them.

•

When passing over bridges or structures, check first that the structure is strong enough to support the weight of the machine. When traveling on public roads, check first with the relevant authorities and follow their instructions.

•

When operating in tunnels, under bridges, under electric wires, or other places where the height is limited, operate slowly and be extremely careful not to let the attachment hit anything.

•

For machines with the canopy specification, when the attachment is operated to the maximum left boom swing with the attachment in the minimum swing posture, soil may spill from the bucket and fall on to the floor. Be extremely careful when operating in this position.

MX15 Operator’s Manual Safe Machine Operation Traveling on Slopes To prevent the machine from tipping over or slipping to the side, always do as follows.

•

Keep the attachment approx. 20-30 cm (8-12”) above the ground. In case of emergency, lower the attachment to the ground immediately to help stop the machine.

•

When traveling up slopes, set the operator's cab facing uphill, when traveling down slopes, set the operator's cab facing downhill. Always check the firmness of the ground under the front of the machine when traveling.

•

When traveling up a steep slope, extend the attachment to the front to improve the balance, keep the attachment approximately 20-30 cm (8-12”) above the ground, and travel at low speed.

•

When traveling downhill, lower the engine speed, keep the travel lever close to the neutral position, and travel at low speed.

•

Always travel straight up or down a slope. Traveling at an angle or across the slope is extremely dangerous.

•

Do not turn on slopes or travel across slopes.

Always go down to a flat place to change the position of the machine, then travel on to the slope again.

•

Travel on grass, fallen leaves, or wet steel plates with low speed. Even with slight slopes there is a hazard that the machine may slip.

•

If the engine stops when the machine is traveling on a slope, move the control levers immediately to the neutral position and start the engine again.

Safety - 33

Safety - 34

MX15 Operator’s Manual Safe Machine Operation

Operations on Slopes •

When working on slopes, there is a hazard that the machine may lose its balance and turn over when the swing or backhoe are operated. This may lead to serious injury or property damage, so always provide a stable place when carrying out these operations, and operate carefully.

•

Do not swing the backhoe from the uphill side to the downhill side when the bucket is loaded. This operation is dangerous, and may cause the machine to tip over.

•

If the machine has to be used on a slope, pile the soil to make a platform that will keep the machine as horizontal as possible.

Prohibited Operations •

Never dig the work face under an overhang. There is a hazard that rocks may fall or that the overhang may collapse and fall on top of the machine.

•

Do not excavate too deeply under the front of the machine. The ground under the machine may collapse and cause the machine to fall.

MX15 Operator’s Manual Safe Machine Operation •

To make it easier to escape if there is any problem, set the tracks at right angles to the road shoulder or cliff with the sprocket at the rear when carrying out operations.

•

Do not carry out demolition work under the machine. There is a hazard that the machine may become unstable and tip over.

•

When working on or from the top of buildings or other structures, check the strength and the structure before starting operations. There is a hazard of the building collapsing and causing serious injury or damage.

•

When carrying out demolition work, do not carry out demolition above your head. There is a hazard of broken parts falling or of the building collapsing and causing serious injury or property damage.

•

Do not use the impact force of the backhoe for breaking work. There is a hazard of damage to the backhoe or a hazard of serious personal injury being caused by flying pieces of broken materials or the machine tipped over due to reaction from the impact.

•

Generally speaking, the machine is more liable to overturn when the backhoe is at the side than when it is at the front or rear.

Safety - 35

Safety - 36

MX15 Operator’s Manual Safe Machine Operation

•

•

When using a breaker or other heavy attachment, there is a hazard of the machine losing its balance and tipping over. When operating on flat ground as well as on slopes.

•

Do not suddenly lower, swing, or stop the attachment.

•

Do not suddenly extend or retract the boom cylinder. There is a hazard that impact will cause the machine to tip over.

Do not pass the bucket over any worker's head or over the operator's cab of the truck or hauling machine. The load may fall or the bucket may come into contact and cause serious personal injury or property damage.

Operations on Snow •

Snow-covered or frozen surfaces are slippery, so be extremely careful when traveling or operating the machine, and do not operate the levers suddenly. Even a slight slope may cause the machine to slip, so be particularly careful when working on slopes.

•

With frozen ground surfaces, the ground becomes soft when the temperature rises, and this may cause the machine to tip over.

•

If the machine enters deep snow, there is a hazard that it may tip over or become buried in the snow.

Be careful not to leave the road shoulder or to get trapped in a snow drift.

•

When clearing snow, the road shoulder and objects placed beside the road are buried in the snow and cannot be seen. There is a hazard of the machine tipping over or hitting covered objects, so always carry out operations carefully.

Parking Machine •

Park the machine on firm, level ground.

•

Select a place where there is no hazard of falling rocks or landslides, or of flooding if the land is low.

•

Lower the attachment completely to the ground.

MX15 Operator’s Manual

Safety - 37

Safe Machine Operation •

When leaving the machine, set safety lock lever (1) to the LOCK position, then stop the engine.

•

Always close the operator's cab door, and use the key to lock all the equipment in order to prevent any unauthorized person from moving the machine.

Always remove the key, take it with you, and leave it in a specified place.

•

If it is necessary to park the machine on a slope, always do as follows.

•

Set the bucket on the downhill side, then dig it into the ground.

•

Put blocks under the tracks to prevent the machine from moving.

Lock Free

Safety - 38

MX15 Operator’s Manual Safe Machine Operation

Transportation Loading and Unloading When loading or unloading the machine, mistaken operation may bring the hazard of the machine tipping over or falling, so particular care is necessary. Always do as follows.

•

Perform loading and unloading on firm, level ground only. Maintain a safe distance from the edge of the road or cliff.

•

Never use the backhoe to load or unload the machine. There is danger that the machine may fall or tip over.

•

Always use ramps of adequate strength. Be sure that the ramps are wide, long, and thick enough to provide a safe loading slope. Take suitable steps to prevent the ramps from moving out of position or coming off.

•

Be sure the ramp surface is clean and free of grease, oil, ice and loose materials. Remove dirt from machine tracks. On a rainy day, in particular, be extremely careful since the ramp surface is slippery.

•

Run the engine at low speed and travel slowly.

•

When on the ramps, do not operate any lever except for the travel lever.

•

Never correct your steering on the ramps. If necessary, drive off the ramps, correct the direction, then enter the ramps again.

•

The center of gravity of the machine will change suddenly at the joint between the ramps and the track or trailer, and there is danger of the machine losing its balance. Travel slowly over this point.

•

When loading or unloading to an embankment or platform, make sure that it has suitable width, strength, and grade.

•

When swinging the upper structure on the trailer, the trailer is unstable, so pull in the backhoe and swing slowly. And turn swing lock switch ON to apply swing lock after loading machine.

•

For machines equipped with a cab, always lock the door after boarding the machine. If this is not done, the door may suddenly open during transportation. Refer to “Transportation” on page 120.

MX15 Operator’s Manual

Safety - 39

Safe Machine Operation Shipping the Machine When shipping the machine on a trailer, do as follows.

•

The weight, transportation height, and overall length of the machine differ according to the attachment, so be sure to confirm the dimensions.

•

When passing over bridges or structures on private land, check first that the structure is strong enough to support the weight of the machine. When traveling on public roads, check first with the relevant authorities and follow their instructions.

•

For details of the shipping procedure, see “Transportation” on page 120.

Battery Battery Hazard Prevention Battery electrolyte contains sulfuric acid, and batteries generate flammable hydrogen gas, which may explode. Mistaken handling can lead to serious injury or fire. For this reason, always observe the following precautions.

•

Do not use or charge the battery if the battery electrolyte level is below the LOWER LEVEL line. This may cause an explosion. Always check the battery electrolyte level periodically and add distilled water to bring the electrolyte level to the UPPER LEVEL line.

•

When working with batteries, always wear safety glasses and rubber gloves.

•

Never smoke or use any flame near the battery.

•

If you spill acid on your clothes or skin, immediately flush the area with large amount of water.

•

If acid gets into your eyes, flush them immediately with large amount of water and seek medical attention.

•

Before working with batteries, turn the starting switch to the OFF position.

Safety - 40

MX15 Operator’s Manual Safe Machine Operation

As there is a hazard that sparks will be generated, always do as follows.

•

Do not let tools or other metal objects make any contact between the battery terminals. Do not leave tools or other metal objects lying around near the battery.

•

Always disconnect the negative (-) terminal (ground side) first when removing the battery; when installing the battery, connect the positive (+) terminal first, and connect the ground last. Tighten the battery terminals securely.

•

Flammable hydrogen gas is generated when the battery is charged, so remove the battery from the chassis, take it to a well-ventilated place, and remove the battery caps before charging it.

•

Tighten the battery caps securely.

•

Install the battery securely to the determined place.

Starting Engine with Jumper Cables If any mistake is made in the method of connecting the jumper cables, it may cause the battery to explode, so always do as follows.

•

When starting with a jumper cable, carry out the starting operation with two workers (one worker sitting in the operator's seat and the other working with the battery).

•

When starting from another machine, do not allow the two machines to touch.

•

When connecting the jumper cables, turn the starting switch OFF for both the normal machine and problem machine. There is a hazard that the machine will move when the power is connected.

•

Be sure to connect the positive (+) cable first when installing the jumper cables. Disconnect the negative (-) cable (ground side) first when removing them.

•

When removing the jumper cables, be careful not to let the jumper cable clips touch each other or to let the clips touch the machine.

•

Always wear safety goggles and rubber gloves when starting the engine with jumper cables.

•

When connecting a normal machine to a problem machine with jumper cables, always use a normal machine with the same battery voltage as the problem machine.

•

For details of the starting procedure when using jumper cables, see “Starting Engine with Jumper Cables” on page 135.

MX15 Operator’s Manual

Safety - 41

Safe Machine Operation

Towing Safety Rules for Towing Serious injury or death could result if a disabled machine is towed incorrectly or if there is a mistake in the selection or inspection of the wire rope.

For towing, see “Towing the Machine” on page 132.

•

Always wear leather gloves when handling wire rope.

•

Fix the wire rope to the track frame.

•

During the towing operation, never stand between the towing machine and the machine being towed.

•

Never tow a machine on a slope.

•

Never use a wire rope which has cut strands (A), reduced diameter (B), or kinks (C). There is danger that the rope may break during the towing operation.

Safety - 42

MX15 Operator’s Manual Safe Machine Operation

Lifting Objects with Bucket Safety Rules for Lifting Objects •

Do not carry out lifting work on slopes, soft ground, or other places where the machine is not stable.

•

Use wire rope that conforms to the specified standard.

•

Do not exceed the specified lifting load. For details of the maximum lifting load permitted for this machine, see “Bucket with Hook” on page 195.

•

It is dangerous if the load hits any worker or structure. Always check carefully that the surrounding area is safe before swinging or turning the machine.

•

Do not start, swing, or stop the machine suddenly. There is a hazard that the lifted load will swing.

•

Do not pull the load to the side or in toward the machine.

•

Do not leave the operator's seat when there is a raised load.

MX15 Operator’s Manual

Safety - 43

Safe Maintenance Information

Safe Maintenance Information Warning Tag •

Always attach the “DO NOT OPERATE“ warning tag to the attachment control lever in the operator's cab to alert others that you are performing service or maintenance on the machine. Attach additional warning tags around the machine if necessary.

•

Warning tag P/N 453-992

•

Keep this warning tag in the tool box while it is not used. If there is no toolbox, keep the tag in the operation manual pocket.

•

If others start the engine, or touch or operate the attachment control lever while you are performing service or maintenance, you could suffer serious injury or property damage.

Keep Work Place Clean and Tidy Do not leave hammers or other tools lying around in the work place. Wipe up all grease, oil, or other substances that will cause you to slip. Always keep the work place clean the tidy to enable you to carry out operations safely. If the work place is not kept clean and tidy, there is the danger that you will trip, slip, or fall over and injure yourself.

Appoint Leader When Working with Others When repairing the machine or when removing and installing the attachment, appoint a leader and follow his instructions during the operation. When working with others, misunderstandings between workers can lead to serious accidents.

Safety - 44

MX15 Operator’s Manual Safe Maintenance Information

Stop Engine Before Carrying Out Maintenance •

Stop the machine on firm, level ground.

•

Select a place where there is no hazard of falling rocks or landslides, or of flooding if the land is low.

•

Lower the attachment completely to the ground and stop the engine.

•

Place the attachment control lever to the HOLD position and set safety lock lever (1) to the LOCK position.

•

Stop the engine.

Lock Free

•

Put blocks under the track to prevent the machine from moving.

MX15 Operator’s Manual

Safety - 45

Safe Maintenance Information Two Workers for Maintenance When Engine is Running To prevent injury, do not carry out maintenance with the engine running. If maintenance must be carried out with the engine running, carry out the operation with at least two workers and do as follows.

•

One worker must always sit in the operator's seat and be ready to stop the engine at any time. All workers must maintain contact with the other workers.

•

Set safety lock lever (1) to the LOCK position.

•

When carrying out operations near the fan, fan belt, or other rotating parts, there is a hazard of being caught in the parts, so be careful not to come close.

•

Do not touch any control levers. If any control lever must be operated, give a signal to the other workers to warn them to move to a safe place.

•

Lock Free

Never drop or insert tools or other objects into the fan or fan belt. Parts may break or be sent flying.

Proper Tools Use only tools suited to the task and be sure to use the tools correctly. Using damaged, low quality, faulty, makeshift tools or improper use of the tools could cause serious personal injury.

Personnel Only authorized personnel can service and repair the machine. Do not allow unauthorized personnel into the area. If necessary, employ an observer.

Safety - 46

MX15 Operator’s Manual Safe Maintenance Information

Accumulator The accumulator is charged with high-pressure nitrogen gas. When handling the accumulator, careless procedure may cause an explosion which could lead to serious injury or property damage. For this reason, always observe the following precautions.

•

Do not disassemble the accumulator.

•

Do not bring it near flame or dispose of it in fire.

•

Do not make holes in it, weld it, or use a cutting torch.

•

Do not hit or roll the accumulator, or subject it to any impact.

•

When disposing of the accumulator, the gas must be released. Please contact your Ditch Witch dealer to have this work performed.

Attachments •

Appoint a leader before starting removal or installation operations for attachments.

•

Place attachments that have been removed from the machine in a stable condition so that they do not fall and take steps to prevent unauthorized persons from entering the storage area.

Work Under the Machine •

If it is necessary to go under the backhoe or the machine to carry out service and maintenance, support the backhoe and machine securely with blocks and stands strong enough to support the weight of the backhoe and machine.

•

It is extremely dangerous to work under the machine if the tracks are lifted off the ground and the machine is supported only with the backhoe. If any of the control levers is touched by accident, or there is damage occurring to the hydraulic hoses, the backhoe or the machine will suddenly drop.

This is extremely dangerous. Never work under the backhoe or the machine.

MX15 Operator’s Manual

Safety - 47

Safe Maintenance Information Noise When carrying out maintenance of the engine and you are exposed to noise for long periods of time, wear ear covers or ear plugs while working. If the noise from the machine is too loud, it may cause temporary or permanent hearing problems.

When Using Hammer When using a hammer, pins may fly out or metal particles may be scattered. This may lead to serious injury. Always do as follows.

•

If hard metal parts such as pins, bucket teeth, cutting edges, or bearings are hit with a hammer, there is a hazard that pieces might be scattered and cause injury. Always wear safety goggles and gloves.

•

When hitting pins or bucket teeth, there is a hazard that broken pieces might be sent flying and injure people in the surrounding area. Always check that there is no one in the surrounding area.

•

There is a hazard that the pin hit with strong force may fly out and injure people in the surrounding area.

Welding Works Welding operations must always be carried out by a qualified welder and in a place equipped with proper equipment. There is a hazard of gas, fire, or electrocution when carrying out welding, so never allow any unqualified personnel to carry out welding.

Removing Battery Terminals When repairing the electrical system or when carrying out electrical welding, remove the negative (-) terminal of the battery to prevent the flow of current.

Safety - 48

MX15 Operator’s Manual Safe Maintenance Information

Safety First When Using High-Pressure Grease to Adjust Track Tension •

Grease is pumped into the track tension adjustment system under high pressure. If the specified procedure for maintenance is not followed when making adjustment, grease drain plug (1) may fly out and cause serious injury or property damage.

•

When loosening grease drain plug (1) to loosen the track tension, never loosen it more than one turn.

Loosen the grease drain plug slowly.

•

Never put your face, hands, feet, or any other part of your body close to grease drain plug (1).

Do Not Disassemble Recoil Springs Never attempt to disassemble the recoil spring assembly. It contains a spring under high pressure which serves as a shock absorber for the idler. If it is disassembled by mistake, the spring will fly out and cause serious injury. When it becomes necessary to disassemble it, ask your Ditch Witch dealer to do the work.

MX15 Operator’s Manual

Safety - 49

Safe Maintenance Information Safety Rules for High-Pressure Oil The hydraulic system is always under internal pressure. When inspecting or replacing hoses, always check that the pressure in the hydraulic circuit has been released. If the circuit is still under pressure, it will lead to serious injury, so always do as follows.

•

Always release the pressure before starting any inspection or replacement operation.

•

If there is any leakage from the hoses, the surrounding area will be wet, so check for cracks and swelling in the hoses. When carrying out inspection, wear safety glasses and leather gloves.

•

There is a hazard that high-pressure oil leaking from small holes may penetrate your skin or cause blindness if it contacts your eyes directly. If you are hit by a jet of high-pressure oil and suffer injury to your skin or eyes, wash the place with clean water, and consult a doctor immediately for medical attention.

Safety Handling High-Pressure Hoses If oil or fuel leaks from high-pressure hoses, it may cause fire or defective operation, which may lead to serious injury. If any loose bolts are found, stop work and tighten to the specified torque. If any damaged hoses are found, stop operations immediately and contact your Ditch Witch dealer.

Replace the hose if any of the following problems are found.

•

Damaged or leaking hydraulic fitting

•

Frayed or cut covering or exposed reinforcement wire layer

•

Covering swollen in places

•

Twisted or crushed movable portion

•

Foreign material embedded in covering

Safety - 50

MX15 Operator’s Manual Safe Maintenance Information

Waste Materials To prevent pollution, pay careful attention to the method of disposing of waste materials.

•

Always put oil drained from your machine in containers. Never drain oil directly onto the ground or dump into the sewage system, rivers, the sea, or lakes.

•

Obey appropriate laws and regulations when disposing of harmful objects such as oil, fuel, coolant, solvent, filters, and batteries.

Air Conditioner Maintenance If air conditioner refrigerant gets into your eyes, it may cause blindness; if it touches your skin, it may cause frostbite. Never touch refrigerant.

Compressed Air •

When carrying out cleaning with compressed air, there is a hazard of serious injury caused by flying particles.

•

When using compressed air to clean elements or the radiator, always wear safety goggles, dust mask, gloves, and other protective equipment.

Periodic Replacement of Safety Critical Parts •

For using the machine safely for an extended period of time, replace safety-critical parts like hoses and seat belts periodically.

•

The material of these components naturally changes over time, and repeated use causes deterioration, wear, and fatigue. As a result, there is a hazard that these components may fail and cause serious injury or death. It is difficult to judge the remaining life of these components from external inspection or the feeling when operating, so always replace them at the specified interval.

•

Replace or repair safety-critical parts if any defect is found, even when they have not reached the time specified interval.

MX15 Operator’s Manual

Operation - 51

Operation Chapter Contents Machine View Illustration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 •

Overall Machine View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53

•

Controls and Gauges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Detailed Controls and Gauges . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 •

Monitoring System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

•

Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

•

Control Levers and Pedals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

•

Cover with Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

•

Engine Hood . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

•

Fuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

•

In-Line Fuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

•

Operator’s Manual Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

•

Tipping Operator’s Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

Machine Operations and Controls . . . . . . . . . . . . . . . . . . . . . . . . 73 •

Before Starting Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

•

Starting Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

•

After Starting Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88

•

Stopping the Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

•

Check After Engine Shutoff . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92

•

Machine Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92

•

Steering the Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96

•

Swinging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98

•

Backhoe Controls and Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99

•

Prohibited Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101

•

General Operation Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .104

•

Traveling on Slopes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105

•

Escape from Mud . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107

•

Work Possible Using Compact Hydraulic Excavator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108

•

Bucket Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110

Operation - 52

MX15 Operator’s Manual

•

Parking Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111

•

Machine Inspection After Daily Work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113

•

Locking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113

•

Rubber Tracks and Turf-Friendly Tracks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114

Transportation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 •

Loading and Unloading with Trailer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120

•

Lifting Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124

Cold Weather Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126 •

Cold Weather Operation Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126

•

After Daily Work Completion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128

•

After Cold Weather Season . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128

Long-Term Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129 •

Before Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129

•

During Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129

•

After Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130

Troubles and Actions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131 •

Running Out of Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131

•

Phenomena That Are Not Failures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .131

•

Towing the Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132

•

Severe Job Condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132

•

Discharged Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133

•

Other Trouble . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .137

MX15 Operator’s Manual

Operation - 53

Machine View Illustrations

Machine View Illustrations Overall Machine View

(1) Bucket

(7) Track shoe

(2) Bucket cylinder

(8) Sprocket

(3) Arm

(9) Track frame

(4) Arm cylinder

(10) Idler

(5) Boom

(11) Blade cylinder

(6) Boom cylinder

(12) Blade

MX15 Operator’s Manual

Operation - 54

Machine View Illustrations

Controls and Gauges

(1) Operator’s seat

(12) Pedal lock

(2) Safety lock levers

(13) Boom swing control pedal

(3) Left attachment control lever

(14) Blade control/track width lever

(4) Travel levers

(15) Traveling accelerator pedal

(5) Horn switch

(16) Service meter

(6) Right attachment control switch

(17) Engine coolant temperature gauge

(7) Blade control lever

(18) Fuel gauge

(8) Monitor panel

(19) Engine oil pressure monitor

(9) Fuel control lever

(20) Engine pre-heating monitor

(10) Starting switch

(21) Charge level monitor

(11) Lamp switch

MX15 Operator’s Manual

Operation - 55

Detailed Controls and Gauges

Detailed Controls and Gauges The following is an explanation of the devices needed for operating the machine.

To carry out suitable operations correctly and safely, it is important to understand fully the methods of operating the equipment and the meanings of the displays.

Machine Monitor

A: Emergency stop items

B: Meter display portion

MX15 Operator’s Manual

Operation - 56

Detailed Controls and Gauges Emergency Stop Items

CAUTION If the monitor flashes, stop the engine immediately or run at low idle, then inspect the problem point immediately and repair the problem.

These are items that should be watched when the engine is running. If any abnormality occurs, the monitor for the problem point lights up and the buzzer sounds. Take action immediately.

(1) Engine oil pressure monitor

(2) Charge level monitor

Engine Oil Pressure Monitor This monitor (1) flashes and buzzer sounds if the engine lubricating oil pressure goes below the specified level. If it flashes, stop the engine and check the oil level.

REMARK • While the starting switch is ON, the lamp will remain lit and will go off once the engine is started. •

When the engine is started or stopped with the starting switch in the ON position, the lamp may light up and the buzzer may sound momentarily, but this does not indicate any abnormality.

MX15 Operator’s Manual

Operation - 57

Detailed Controls and Gauges Charge Level Monitor This monitor (2) indicates an abnormality in the charging system while the engine is running.

If the monitor lamp flashes, stop the engine and check the V-belt tension. If any abnormality is found, see “Other Trouble� on page 137.

REMARK While the starting switch is ON, the lamp will remain lit and will go off once the engine is started.

Meter Display Portion

(1) Service meter (2) Engine coolant temperature gauge

(3) Fuel gauge (4) Engine pre-heating monitor

Service Meter This meter (1) indicates the total number of hours that the machine has been operated.

Set the intervals for periodic maintenance according to the time display. The service meter advances while the starting switch is on even if the machine is not moving.

While the engine is running, operation display (A) under the meter will light to show that the meter is advancing.

The meter will advance by 1 for each hour of operation regardless of the engine speed.

Operation - 58

MX15 Operator’s Manual Detailed Controls and Gauges

Engine Coolant Temperature Gauge This monitor (2) lights up if the engine coolant temperature goes above the specified level. If it lights up, run the engine at low idle and wait until the monitor goes out (until the engine coolant temperature goes down).

Fuel Gauge This meter (3) shows the fuel level in the fuel tank.

During normal operation, the lamp should light up in the green range.

If the indicator goes down to the E range during operation, there is less than 3.5 L (0.9 gal) of fuel remaining, so check and add fuel.

The correct level may not be displayed for a short time after the starting switch is turned to the ON position, but this is not an abnormality.

Engine Pre-Heating Monitor This monitor lamp (4) indicates the pre-heating time required when starting the engine an ambient temperature below 0°C (32°F).

This monitor lamp lights when the starting switch is turned to the HEAT position and goes off after about 18 seconds.

MX15 Operator’s Manual

Operation - 59

Detailed Controls and Gauges

Switches

(1) Starting switch (2) Horn switch

(3) Lamp switch

Operation - 60

MX15 Operator’s Manual Detailed Controls and Gauges

Starting Switch This switch (1) is used to start or stop the engine.

•

OFF position: The key can be inserted or withdrawn. The switches for the electric system are all turned off and the engine is stopped.

•

ON position: Electric current flows in the charging and lamp circuits. Keep the starting switch key at the ON position while the engine is running.

•

START position: This is the engine start position.

Keep the key at this position during cranking.

Immediately after starting the engine, release the key. It will automatically return to the ON position.

•

HEAT (pre-heat) position: When starting the engine in cold weather, turn the key to this position. When the key is set to the HEAT position, the preheating monitor lights up. Keep the key at this position until the preheating monitor goes out. When the preheating monitor goes out, release the key. When the key is released, it will return to the OFF position, so turn it immediately to START and start the engine.

Horn Switch Press switch (2) at the center of the knob of the right attachment lever to sound the horn.

Lamp Switch This switch (3) lights up the head lamps and the panel lamp.

•

ON position: Head lamp and panel lamp light up.

•

OFF position: Lamps go off.

MX15 Operator’s Manual

Operation - 61

Detailed Controls and Gauges

Control Levers and Pedals

(1) Safety lock lever (for left and right attachment control levers)

(6) Travel levers (7) Pedal lock (for boom swing control pedal)

(2) Left attachment control lever (8) Boom swing control pedal (3) Right attachment control lever (9) Traveling accelerator pedal (4) Fuel control lever (10) Track width/blade selector control lever (5) Blade control/track width lever

MX15 Operator’s Manual

Operation - 62

Detailed Controls and Gauges Safety Lock Lever (For left and right attachment control levers)

WARNING •

When leaving the operator's compartment, set the safety lock lever securely to the LOCK position. If the safety lock lever is not at the LOCK position and the control levers are touched by mistake, it may lead to serious personal injury.

•

If the safety lock lever is not placed securely at the LOCK position, the control lever may move and cause a serious accident or injury. Check that the condition of the lever is as shown in the diagram.

•

Even if the safety lock lever is set to the LOCK position, the travel, blade, and boom swing controls are not locked.

•

When pulling the safety lever up, be careful not to touch the attachment control lever.

•

When pushing the safety lever down, be careful not to touch the attachment control lever.

This lever (1) is a device to lock the backhoe and upper structure.

When the lever is pulled up, the lever stand springs up and is locked.

This safety lock lever is hydraulically actuated. When it is in the LOCK position, the attachment control lever and travel control lever are still movable, but none of the attachment, swing and travel motors works.

MX15 Operator’s Manual

Operation - 63

Detailed Controls and Gauges Attachment Control Lever (with auto-deceleration device) This left attachment control lever (2) is used to operate the arm and upper structure.

Swing operation •

(a) Swing to right

•

(b) Swing to left

Arm operation •

(c) Arm IN

•

(d) Arm OUT

N (Neutral): The upper structure and arm are held in that position when they come to a stop and do not move.

This right attachment control lever (3) is used to operate the boom and bucket.

Boom operation •

(e) RAISE

•

(f) LOWER

Bucket operation •

(g) DUMP

•

(h) CURL

N (Neutral): The boom and bucket are held in that position when they come to a stop and do not move.

MX15 Operator’s Manual

Operation - 64

Detailed Controls and Gauges Fuel Control Lever This lever (4) is used to control the engine speed and output.

•

(a) Low idle: Push the lever fully.

•

(b) High idle: Pull the lever fully.

Blade Control/Track Width Lever NOTICE • This lever is not locked even when the safety lock lever is at the LOCK position, so when not operating the blade, be careful not to touch this lever.

•

When digging operations using the blade are continued for more than one hour, pay careful attention to the rise in the coolant temperature.

•

Before starting operations, check the setting of the track width/blade selector control lever.

This lever (5) is used to control the blade and track width.

Lever position

(a)

(b)

Blade movement

lower

raise

Track movement

close

open

MX15 Operator’s Manual

Operation - 65

Detailed Controls and Gauges Travel Levers

WARNING •

If the track frame is facing the rear, the direction of travel operations will be reversed.

•

When operating the travel levers, check if the track frame is facing the front or the rear. (If sprocket [A] is at the rear, the track frame is facing the front.)

This lever (6) is used to change the direction of travel.

•

(a) Forward: The lever is pushed forward.

•

(b) Reverse: The lever is pulled back.

•

N (Neutral): The machine stops.

REMARK If the lever is shifted to the forward or reverse position from the neutral position, the alarm sounds to warn that the machine is starting to advance.

MX15 Operator’s Manual

Operation - 66

Detailed Controls and Gauges Pedal Lock (For boom swing control pedal)

WARNING When boom swing operation is not required, lock the boom with the pedal lock. If the operation pedal is accidentally pressed while it is not lock, a serious accident or injury could occur.

This pedal (7) is used to lock the boom swing control pedal. The pedal is locked by fitting the plate over the pedal.

Boom Swing Control Pedal

WARNING If the bucket is wider than the standard bucket, there is danger that the bucket will contact the operator’s cab when swinging the boom to the left with the backhoe pulled in. Check the distance between the bucket and the cab during the operation and operate the backhoe slowly.

This pedal (8) is used to swing the boom.

•

(a) Boom swings to the right.

•

(b) Boom swings to the left.

•

N (Neutral): Boom is stopped and held in this position.

MX15 Operator’s Manual

Operation - 67

Detailed Controls and Gauges Traveling Accelerator Pedal If the pedal (9) is depressed, the machine speed will increase.

3.2-4.3 km/h (2.0-2.7mph) when engine is at full throttle.

Track Width/Blade Selector Control Lever

WARNING •

Adjust to the narrow gauge only when traveling or digging in confined spaces. In all other travel or digging operations, always set to the broad gauge.

•

Do not change the track width on slopes. There is danger that the left-to-right stability may change.

•

Always operate the track width on flat ground.

When operating the blade control lever, check the position of the selector lever before operating.

This lever (10) switches between the track width and blade control.

•

To control track width, move to position a.

•

To control blade, move to position b.

For details of the method of operating the track width and blade, see the section on the “Blade Control/Track Width Lever” on page 64.

Operation - 68

MX15 Operator’s Manual Detailed Controls and Gauges

Variable Blade NOTICE •

Use the same width for the track width and blade.

•

Operate the variable blade only when the track width is fully retracted. If the variable blade is operated when the track width is extended, the blade will contact the track and stop it from rotating.

Setting Blade to Minimum Width Remove pin (1), turn blade (2) to align pin hole (3) and the hole in blade (2), then insert pin (1) again.

Setting Blade to Maximum Width Remove pin (1), turn blade (2) to align pin hole (3) and the hole in blade (2), then insert pin (1) again.

MX15 Operator’s Manual

Operation - 69

Detailed Controls and Gauges

Cover with Lock Locks are installed to the cover on the right side of the machine, the operator’s cab, engine hood, and tool box. Use the starting switch key to lock or unlock these places.

Opening and Closing Covers with Lock Insert the key as far as it will go to the shoulder. If the key is turned before it is inserted all the way, it may break.

Opening the Cover 1. Insert the key into the cap.

2. Turn the key clockwise and open the cover.

Locking the Cover 1. Turn the cap into place.

2. Turn the key counterclockwise and take the key out.

MX15 Operator’s Manual

Operation - 70

Detailed Controls and Gauges

Engine Hood

CAUTION When carrying out inspection or maintenance inside the engine hood, raise the hood fully and be sure to fix it in position with the hood support lever.

NOTICE Always keep the hood locked except when opening the hood. It is possible to check open or lock positions by looking at the direction of the key groove in the open knob.

1. To open hood, pull engine hood knob (1) to release the lock.

2. To close hood, push hood (2) down fully.

MX15 Operator’s Manual Detailed Controls and Gauges

Fuse NOTICE Before replacing a fuse, be sure to turn off the starting switch.

The fuse box is under the seat.

The fuses protect the electrical equipment and wiring from burning out.

If the fuse becomes corroded, white powder can be seen, or the fuse is loose in the fuse holder, replace the fuse. Replace the fuse with another of the same capacity.

Fuse Capacities and Circuit Names

No.

Fuse capacity

Name of circuit

(1)

30A

Room lamp, radio (back-up), starting motor terminal B (stop solenoid)

(2)

20A

Alarm buzzer, monitor panel, solenoid, pump adjuster

(3)

5A

Wiper, radio, horn, window washer, throttle actuator

(4)

30A

Stop solenoid, stop relay, timer

(5)

5A

Spare fuse

In-Line Fuse If the starting motor does not turn even when the starting switch is turned to the ON position, in-line fuse (1) is probably blown, so open the cover at the right side of the machine and check or replace the fuse.

This is at the top surface of the battery.

REMARK An in-line fuse is a large fuse wire installed to the circuit where a large-capacity current is flowing. It acts in the same way as a normal fuse to protect the electrical equipment and wiring from burning out under abnormal current.

Operation - 71

Operation - 72

MX15 Operator’s Manual Detailed Controls and Gauges

Operator’s Manual Storage There is a box provided in the rear of the operator’s seat to keep the operator’s manual. Keep the operator’s manual in this box so that you can read it when you need it.

Tipping Operator’s Seat When carrying out inspection or maintenance, tip the operator’s seat as follows.

1. Move the operator’s seat to the front, then remove butterfly nut (1) under the seat.

2. Tip operator’s seat (2) up and over to the front and lock it in position.

MX15 Operator’s Manual

Operation - 73

Machine Operations and Controls

Machine Operations and Controls Before Starting Engine Walk-Around Checks Before starting the engine, look around the machine and under the machine to check for loose nuts or bolts, or leakage of oil, fuel, or coolant, and check the condition of the attachment and hydraulic system.

Check also for loose wiring, play, and accumulation of dust at places which reach high temperatures.

WARNING •

If you open the engine hood, then fix the hood in position with hood stopper.

•

Remove any flammable materials from around the battery or engine muffler or other high temperature engine parts. Leakage of fuel or oil will cause the machine to catch fire. Check carefully, and be sure to repair any abnormalities, or please contact your Ditch Witch dealer.

Carry out the following inspections and cleaning every day before starting the engine for the day's work.

1. Check for damage, wear, play in attachment, cylinders, linkage, hoses. Check that there are no cracks, excessive wear, or play in the attachment, cylinders, linkage, or hoses. If any abnormality is found, repair it.

2. Remove dirt and dust from around engine, battery, and radiator. Check that there is no dirt or dust accumulated around the engine or radiator. Check also that there is no flammable material (dry leaves, twigs, etc.) accumulated around the engine muffler or high temperature parts of the engine, or around the battery. Remove all dirt, dust, and flammable materials.

3. Check for leakage of coolant or oil around engine. Check that there is no leakage of oil from the engine or leakage of coolant from the cooling system. If any abnormality is found, repair it.

4. Check for oil leakage from hydraulic equipment, hydraulic tank, hoses, joints. Check that there is no oil leakage. If any abnormality is found, repair the place where the oil is leaking.

5. Check the undercarriage parts. Check track, sprocket, idler, guard for damage, wear, loose bolts, or leakage of oil from rollers, etc. Repair them if any trouble is found.

6. Check the handrails and steps. Check the handrails and steps for any damage or loosened bolts, and repair the damaged part and tighten the loosened bolts, if any.

7. Check for abnormality in gauges and monitor. Check that there is no abnormality in the gauges and monitor in the operator's cab. If any abnormality is found, replace the parts. Clean off any dirt on the surface.

8. Check that there is no abnormality in the seat belt or mounting clamps. If there is any damage, replace with new parts.

MX15 Operator’s Manual

Operation - 74

Machine Operations and Controls Checks Before Starting Always carry out the items of the checks in this section before starting the engine each day.

Check Coolant Level, Add Coolant

WARNING •

Do not open the radiator cap unless necessary. When checking the coolant, always wait for the engine to cool down and check the sub tank.

•

Immediately after the engine is stopped, the coolant is at a high temperature and the radiator is under high internal pressure. If the cap is removed to check the coolant level in this condition, there is a hazard of burns. Wait for the temperature to go down, then turn the cap slowly to release the pressure before removing it.

1. Open the engine hood and check that the coolant level is between the FULL and LOW marks on radiator reserve tank (1, shown). If the coolant level is low, add clean and soft water through the coolant filler of reserve tank (1) to the FULL level.

2. After adding coolant, tighten the cap securely.

3. If the reserve tank is empty, check for leakage of coolant, then check the radiator coolant level. Add coolant to the radiator if necessary, then add coolant to the reserve tank.

MX15 Operator’s Manual

Operation - 75

Machine Operations and Controls Check Oil Level in Engine Oil Pan, Add Oil

WARNING The parts and oil are at high temperature immediately after the engine is stopped, and may cause serious burns. Wait for the temperature to go down before starting the operation.

1. Open engine hood.

2. Remove dipstick (G) and wipe the oil off with a cloth.

3. Insert dipstick (G) fully in the oil filler pipe, then take it out again.

4. The oil level should be between the H and L marks on dipstick (G).

•

If the oil level is below the L mark, add engine oil through oil filler (F).

•

If the oil is above the H mark, drain the excess engine oil from drain plug (P), and check the oil level again.

•

If the oil level is correct, tighten the oil filler cap securely and close the engine hood.

REMARK • When checking the oil level after the engine has been operated, wait for at least 15 minutes after stopping the engine before checking.

•

If the machine is at an angle, make it horizontal before checking.

MX15 Operator’s Manual

Operation - 76

Machine Operations and Controls Check Fuel Level, Add Fuel

WARNING •

When adding fuel, never spill the fuel or let it overflow. It will cause fire. If any fuel has spilled, wipe it up completely. If fuel has spilled over soil or sand, remove that soil or sand.

•

Fuel is highly flammable and dangerous. Never bring flames near fuel.

1. Insert the key in starting switch (1) and turn in to the ON position to light up the monitor.

2. Check the remaining fuel level with fuel gauge (2).

If the level is low, open the cover on the right side, and watch level gauge (G) while adding fuel through fuel filler port (F).

Fuel capacity: 19 L (5 gal) 3. After adding fuel, tighten the cap securely.

REMARK If breather hole on the cap is clogged, the pressure in the tank will drop and fuel will not flow. Clean the hole from time to time.

MX15 Operator’s Manual

Operation - 77

Machine Operations and Controls Check Oil Level In Hydraulic Tank, Add Oil

WARNING When removing the oil filler cap, oil may spurt out, so turn the cap slowly to release the internal pressure before removing the cap.

1. If the backhoe is not in the condition shown in the diagram on the right, start the engine, run the engine at low speed, retract the arm and bucket cylinder rods fully, then lower the boom, set the bucket teeth in contact with the ground, and stop the engine.

2. Open the door of the pump room on the right side of the machine and check sight gauge (G). The oil level should be between the H and L lines.

NOTICE Do not add oil if the level is above the H line. This will damage the hydraulic equipment and cause the oil to spurt out.

3. If the level is below that L mark, add oil through oil filler (F) at the top of the hydraulic tank.

REMARK The oil level will vary depending upon the oil temperature. Accordingly, use the following as the guide: • Before operation: around L level (Oil temperature 10-30°C/50-86°F) •

Normal operation: around H level (Oil temperature 50-80°C/122-176°F)

MX15 Operator’s Manual

Operation - 78

Machine Operations and Controls Check, Clean Fuel Filter Element If red ring (1) of the water separator is at the bottom of case (2), there is no water. If the ring (1) is floating, there is water up to the bottom of the ring, so drain the water as follows.

Prepare the filter wrench for fuel filter.

1. Open the engine hood and set handle to the LOCK position. See “Engine Hood” on page 70.

2. Using the filter wrench, loosen ring (4), then remove case (2) and throw out the water inside it.

3. Set case (2) in position, then tighten ring (4) to install it.

4. Set handle (3) to the OPEN position.

5. Drain any water or sediment from the fuel tank. For details, see “Drain Water and Sediment from Fuel Tank” on page 172.

Check Electric Wiring

WARNING •

If the fuses frequently blow or if there are traces of short circuits on the electrical wiring, locate the cause immediately and carry out repairs, or contact your Ditch Witch dealer for repairs.

•

If flammable materials (dead leaves, twigs, dry grass, etc.) accumulate around the battery, they will cause fire, so always remove such material immediately.

•

Keep the top surface of the battery clean and check the breather hole in the battery cap. If it is clogged with dirt or dust, wash the battery cap to clean the breather hole.

Check that there is no damage to the fuses, that fuses of the specified capacity are used, that there is no disconnection or trace of short-circuiting on the electric wiring and no damage to the covering. Check also that there is no loosened terminal. If so, tighten it.

Moreover, pay particular attention to the electric wiring when checking the battery, engine starting motor and alternator.

Be sure to check that there is no flammable material accumulated around the battery. If present, remove it without fail.

MX15 Operator’s Manual

Operation - 79

Machine Operations and Controls Check Function of Horn 1. Turn the starting switch to the ON position.

2. Confirm that the horn sounds immediately when the horn button is pressed. If the horn does not sound, please contact your Ditch Witch dealer for repair.

Adjustment

WARNING •

Adjust the seat position before starting operations or after changing the operator.

•

Adjust the seat so that the control levers and switches can be operated freely and easily with the operator back against the backrest.

Seat Adjustment (A) Fore-and-Aft Adjustment: Pull lever (1) up, set the operator's seat at the desired position, then release the lever. Adjust the position of the operator's seat to match the operation. For example, when carrying out deep digging operations, slide the seat to the front to improve the view below the front of the machine.

Fore-and-aft adjustment: 100 mm (3.9”) in 5 stages (B) Recline Adjustment: Pull up lever (2) and set the seat back to a position which is comfortable for operation, then release the lever. Sit with your back against the seat back when adjusting. If your back is not touching the seat back, the seat back may suddenly move forward.

(C) Suspension Adjustment: Pull lever (3) up, then move it to the left to make the suspension harder or move it to the right to make the suspension softer. Adjust the lever position to match the weight of the operator and provide the optimal suspension.

Suspension adjustment: 50-120 kg (110-265 lb) in 5 stages.

MX15 Operator’s Manual

Operation - 80

Machine Operations and Controls Seat Belt (Machine equipped with operator’s cab)

WARNING •

Before fastening the seat belt, check that there is no abnormality in the securing brackets or belt. If there is any wear or damage, replace.

•

Even if there appears to be no abnormality in the seat belt, replace the seat belt once every 3 years.

The date of manufacture is woven on the reverse side of the belt.

•

Adjust and fasten the seat belt before operating the machine.

•

Always use the seat belt when operating the machine.

•

Do not use the seat belt with either half of the belt twisted.

Fastening and Removing Check the mounting bolts of the belt fitting on the machine body for looseness, and re-tighten them if necessary. The tightening torque for the mounting bolt is 24.5 ± 4.9 N•m (2.5 ± 0.5 kgf•m,18.1 ± 3.6 lb•ft).

If the belt surface is scratched or frayed or if the fittings are broken or deformed, replace the seat belt unit.

1. Adjust the seat so that the operator still feels that there is sufficient knee room when fully depressing the pedal while seated, with the operator's back against the backrest.

2. After adjusting the seat position, sit in the seat. Grip buckle (1) and tongue (2) in each hand and insert tongue (2) into buckle (1). Confirm by pulling the belt that the tongue is securely locked to the buckle.

3. When removing the belt, raise the tip of buckle (1) lever to release it.

Fasten belt along your body without kinking it.

Adjust the lengths of the belt on the tongue sides.

MX15 Operator’s Manual

Operation - 81

Machine Operations and Controls Seat Belt Adjustment Shortening: Pull the free end on the tongue side.

Lengthening: Pull the fixed end on the tongue side, at right angles to the buckle and tongue.

Operations Before Starting Engine

WARNING •

When starting the engine, check that the safety lock lever is securely at the LOCK position. If the control levers are not locked and they are touched by accident when starting the engine, the backhoe may move unexpectedly, and this may lead to a serious accident.

•

When standing up from the operator’s seat, always set the safety lock lever to the LOCK position, regardless of whether the engine is running or stopped.

Operation - 82

MX15 Operator’s Manual Machine Operations and Controls

1. Check that the safety lock lever (1) is at the LOCK position.

2. Check the position of each lever.

Set the control lever to the NEUTRAL position.

3. Insert the key in starting switch (2), turn the key to the ON position, then carry out the following checks.

The buzzer will sound for approx. 1 second, and the following monitors and gauges will light up for approx. 3 seconds.

•

Charge level monitor (3)

•

Engine coolant temperature gauge (4)

•

Fuel gauge (5)

If the monitors or gauges do not light up or the buzzer does not sound, there is probably a blown bulb or disconnection, so please contact your Ditch Witch dealer for repair.

After approx. 3 seconds, the following gauges will remain on and the other monitors will go out.

•

Engine coolant temperature gauge (4)

•

Fuel gauge (5)

MX15 Operator’s Manual Machine Operations and Controls Turn the lamp switch (6) to the working lamps on position. If it does not light up, there is probably a blown bulb or disconnection, so please contact your Ditch Witch dealer for repair.

Press horn switch (7) to confirm that the horn will sound.

Operation - 83

Operation - 84

MX15 Operator’s Manual Machine Operations and Controls

Starting Engine Normal Starting

WARNING •

Check that there are no persons or obstacles in the surrounding area, then sound the horn and start the engine.

•

Exhaust gas is toxic. When starting the engine in confined spaces, be particularly careful to ensure good ventilation.

NOTICE Do not keep the starting motor rotating continuously for more than 20 seconds. If the engine will not start, wait for at least 2 minutes before trying to start the engine again.

1. Pull fuel control lever (1) slightly from the LOW IDLE position toward the FULL position.

MX15 Operator’s Manual Machine Operations and Controls 2. Turn the key in starting switch (2) to the START position. The engine will start.

3. When the engine starts, release the key in starting switch (2). The key will return automatically to the ON position.

Operation - 85

MX15 Operator’s Manual

Operation - 86

Machine Operations and Controls Starting Engine In Cold Weather

WARNING •

Check that there are no persons or obstacles in the surrounding area, then sound the horn and start the engine.

•

Never use starting aid fluids as they may cause explosions.

NOTICE Do not keep the starting motor rotating continuously for more than 20 seconds. If the engine will not start, wait for at least 2 minutes before trying to start the engine again.

When starting in low temperatures, do as follows.

1. Pull fuel control lever (1) to the center position between LOW IDLE and HIGH IDLE.

2. Hold the key in starting switch (2) at the HEAT position, and check that pre-heating monitor (3) lights up.

After approx. 30 seconds, pre-heating monitor lamp (3) goes off to inform that the preheating is completed.

REMARK The monitor and gauge also light up when the key is at the HEAT position, but this does not indicate any abnormality.

MX15 Operator’s Manual Machine Operations and Controls 3. When pre-heating monitor (3) goes off, turn the key in starting switch (2) to the START position to start the engine.

4. When the engine starts, release the key in starting switch (2). The key will return automatically to the ON position.

5. Continue idling for 15 seconds after the engine starts. During this time, do not operate the control levers or fuel control dial.

Operation - 87

MX15 Operator’s Manual

Operation - 88

Machine Operations and Controls

After Starting Engine

WARNING •

Emergency stop: If there has been any abnormal action or trouble, turn the starting switch key to the OFF position.

•

If the backhoe is operated without warming the machine up sufficiently, the response of the backhoe to the movement of the control lever will be slow, and the backhoe may not move as the operator desires, so always carry out the warm-up operation, Particularly in cold areas, be sure to carry out the warm-up operation fully.

Breaking in the New Machine

CAUTION Your machine has been thoroughly adjusted and tested before shipment. However, operating the machine under severe conditions at the beginning can adversely affect the performance and shorten the machine life.

• Be sure to break in the machine for the initial 100 hours (as indicated by the service meter).

•

During breaking-in operations, follow the precautions described in this manual.

•

Idle the engine for 5 minutes after starting it up.

•

Avoid operation with heavy loads or at high speeds.

•

Immediately after starting the engine, avoid sudden starts, sudden acceleration, unnecessary sudden stops, and sudden changes in direction.

MX15 Operator’s Manual

Operation - 89

Machine Operations and Controls Warm-Up Operation NOTICE • When the hydraulic oil is at a low temperature, do not carry out operations or move the lever suddenly. Always carry out the warm-up operation. This will help to extend the machine life.

•

Do not suddenly accelerate the engine before the warm-up operation is completed.

•

Do not run the engine at low idle or high idle continuously for more than 20 minutes. If it is necessary to run the engine at idle, apply a load from time to time or run the engine at a midrange speed.

After starting the engine, do not immediately start operations. First, carry out the following operations and checks.

1. Pull fuel control lever (1) to the center position between LOW IDLE and HIGH IDLE and run the engine at medium speed for about 5 minutes with no load.

REMARK When the ambient temperature is below 0°C (32°F), keep the fuel control lever close to the 1/4 position when carrying out the warm-up operation.

2. Set the safety lock lever (2) to the FREE position, and raise the bucket from the ground.

Operation - 90

MX15 Operator’s Manual Machine Operations and Controls

3. Operate bucket control lever (3) and arm control lever (4) slowly to move the bucket cylinder and arm cylinder to the end of the stroke.

4. After carrying out the warm-up operation, check that each gauge and monitor lamp is in the following condition.

If there is any abnormality, carry out maintenance and repair.

•

Engine coolant temperature gauge (4): Inside green range

•

Fuel gauge (5): Inside green range

•

Engine oil pressure monitor (6): OFF

•

Charging monitor (7): OFF

•

Pre-heating monitor (8): OFF

5. Check that there is no abnormal exhaust gas color, noise or vibration. If any abnormality is found, contact your Ditch Witch dealer.

6. Set the safety lock lever (2) to the LOCK position and check that it is impossible to operate the swing and backhoe with the left and right attachment control levers.

MX15 Operator’s Manual Machine Operations and Controls

Stopping the Engine NOTICE If the engine is stopped abruptly, service life of component parts of the engine may be considerably reduced. Hence do not stop the engine abruptly except in an emergency. If the engine has overheated, do not try to stop it abruptly but run it at medium speed to allow it to cool down gradually, and then stop it.

1. Run the engine at low idle for about 5 minutes to cool down gradually.

2. Turn the key of starting switch (1) to the OFF position to stop the engine.

3. Remove the key from starting switch (1).

Operation - 91

MX15 Operator’s Manual

Operation - 92

Machine Operations and Controls

Check After Engine Shutoff 1. Walk around the machine and check the backhoe, machine exterior, and undercarriage, and check also for leakage of oil or coolant. If any abnormalities are found, repair them.

2. Fill the fuel tank.

3. Check the engine compartment for paper and debris. Clean out any paper and debris to avoid a fire hazard.

4. Remove any mud stuck to the undercarriage.

Machine Operation Preparations for Moving the Machine Off

WARNING •

Before operating the travel levers, check the direction of the track frame. If the sprocket is at the front, the operation of the travel levers is reversed.

•

When moving off, check that the area around the machine is safe, and sound the horn before moving.

•

Clear all personnel from the machine and the area.

•

Clear all obstacles from the path of the machine.

Pull fuel control lever (1) toward the high idle position to increase the engine speed.

MX15 Operator’s Manual Machine Operations and Controls Moving Machine Forward 1. Set safety lock lever (4) to the FREE position, fold the backhoe, and raise it 40-50 cm (1.6-2.0”) from the ground.

2. Raise the blade.

3. Operate both travel levers (3) as explained below.

When the sprocket (A) is at the rear of the machine: •

Push levers (3) forward slowly to move the machine off.

When the sprocket (A) is at the front of the machine: •

Pull levers (3) backward slowly to move the machine off.

4. When travel accelerator pedal (4) depressed, the speed will increase.

For details if the speed, see “Specifications” on page 189.

Operation - 93

Operation - 94

MX15 Operator’s Manual Machine Operations and Controls

Moving Machine Backward 1. Set safety lock lever (2) to the FREE position, fold the backhoe, and raise it 40-50 cm (1.6-2.0”) from the ground.

2. Raise the blade.

3. Operate both travel levers (3) as explained below.

When the sprocket (A) is at the rear of the machine: •

Pull levers (3) backward slowly to move the machine off.

When the sprocket (A) is at the front of the machine: •

Push levers (3) forward slowly to move the machine off.

4. When travel accelerator pedal (4) depressed, the speed will increase.

For details if the speed, see “Specifications” on page 189.

MX15 Operator’s Manual

Operation - 95

Machine Operations and Controls Stopping Machine

WARNING Avoid stopping suddenly. Give yourself ample room when stopping.

Put the left and right travel levers (1) in the neutral position, then stop the machine.

MX15 Operator’s Manual

Operation - 96

Machine Operations and Controls

Steering the Machine Steering

WARNING Before operating the travel control levers, check the direction of the track frame (i.e. position of the sprocket) first. If the sprocket is at the front, the machine moves in the reverse direction to the operation of the travel lever.

Use the travel levers to change direction.

Avoid sudden changes of direction as far as possible. In particular, when carrying out counter-rotation (spin turn), stop the machine first before turning.

Operate two travel levers (1) as follows.

Steering the Machine when Stopped When turning to the left: Push the right travel lever forward to travel left when traveling forward, and pull it back to turn left when traveling in reverse.

REMARK When turning to the right, operate the left travel lever in the same way.

MX15 Operator’s Manual Machine Operations and Controls Steering when Traveling When turning to the left: If the left travel lever is returned to the neutral position, the machine will turn to the left.

REMARK When turning to the right, operate the right travel lever in the same way.

Counter-Rotation Turn (Spin Turn) When using counter-rotation (spin turn) to turn left, pull the left travel lever back and push the right travel lever forward.

REMARK When using counter-rotation (spin turn) to turn right, pull the right travel lever back and push the left travel lever forward.

Operation - 97

MX15 Operator’s Manual

Operation - 98

Machine Operations and Controls

Swinging

WARNING •

The rear of the machine extends outside the track width. Check that the surrounding area is safe before swinging the upper structure.

•

Check that swing lock monitor is not lit up.

•

If the swing control lever is operated quickly, the upper structure will move quickly; if it is operated slowly, the upper structure will move slowly.

1. Operate left attachment control lever (1) to swing the upper structure.

2. When not using the swing, set left attachment control lever (1) to the N position. The swing holding brake will be applied.

REMARK • When using the swing on a slope, run the engine at low idle and operate the swing lever extremely slowly. Be particularly careful to avoid sudden movement when the bucket is loaded.

•

When the bucket is loaded and the left attachment control lever is operated, the swing holding brake is released, so the upper structure may swing momentarily, but this is not an abnormality.

MX15 Operator’s Manual

Operation - 99

Machine Operations and Controls

Backhoe Controls and Operations

WARNING If the attachment control lever is operated quickly, the backhoe will move quickly; if it is operated slowly, the backhoe will move slowly.

Use the control levers to operate the backhoe. Note that when the levers are released, they return to the HOLD position and the backhoe is held in that position.

Arm Control Move the left attachment control lever to the front or rear to operate the arm.

Swing Control Move the left attachment control lever to the left or right to swing the upper structure.

Boom Control Move the right attachment control lever to the front or rear to operate the boom.

Operation - 100

MX15 Operator’s Manual Machine Operations and Controls

Bucket Control Move the right attachment control lever to the left or right to operate the bucket.

Boom Swing Operation The boom swing operation can be carried out with the boom swing control pedal.

Blade Control Move the lever on the right side of the operator’s seat to the front or rear to operate the blade.

MX15 Operator’s Manual

Operation - 101

Machine Operations and Controls

Prohibited Operations

WARNING Do not attempt to operate the attachment control lever while the machine is traveling.

Operations Using Swing Force Do not use the swing force to compact soil or break earth mounds or walls.

When swinging, do not dig the bucket teeth into the soil.

These operations will damage the backhoe.

Operations Using Travel Force Do not dig the bucket into the ground and use the travel force to carry out excavation. This will damage the machine or backhoe.

Prohibition of Operations Using Hydraulic Cylinders to Stroke Ends When operating the cylinder, do not operate it to the end of its stroke. Always leave a small margin.

If the cylinder is operated to the end of its stroke, force will be brought to bear on the cylinder, and this may cause damage to the pins, boom, arm, and frame.

Operation - 102

MX15 Operator’s Manual Machine Operations and Controls

Operations Using Bucket Dropping Force Do not use the dropping force of the machine for digging, or use the dropping force of the bucket as a pickax, breaker, or pile driver.

This will markedly reduce the life of the machine.

Operations Using Machine Dropping Force Do not use the dropping force of the machine for digging.

Avoid Hitting Blade Be careful not to hit the blade against rocks or boulders.

This will cause premature damage to the blade or cylinders.

MX15 Operator’s Manual Machine Operations and Controls Folding in Backhoe When folding in the backhoe to the travel or transportation position, be careful not to let the bucket hit the blade.

Support Blade on Both Sides When using the blade as an outrigger, never support the machine with only one end of the blade.

Blade During Backhoe Operations When carrying out deep digging operations with the blade at the front, be careful not to the boom cylinder hit the blade. Always position the blade at the back unless it is needed at the front.

Operation - 103

MX15 Operator’s Manual

Operation - 104

Machine Operations and Controls

General Operation Information Traveling When traveling over obstacles such as boulders or tree stumps, the machine (in particular, the undercarriage) is subjected to a large shock, so reduce the travel speed and travel over the obstacle at the center of the tracks.

As far as possible, remove such obstacles or avoid traveling over them.

When the track width is fully retracted, there is particular danger of the machine tipping over to the left or right if the rubber crawler on one side travels over obstacles such as boulders or tree stumps or goes into a ditch or hole. In such places, lower the travel speed and be extremely careful to maintain the machine balance when traveling.

Permissible Water Depth

CAUTION When driving the machine out of water, if the angle of the machine exceeds 15°, the rear of the upper structure will go under water, and water will be thrown up by the radiator fan. This may cause the fan to break.

Be extremely careful when driving the machine out of water.

Do not drive the machine in water deeper than the center of carrier roller (1).

In addition, for parts that have been immersed in water for a long time, pump in grease until the old grease comes out from the bearings (around the bucket pins).

MX15 Operator’s Manual

Operation - 105

Machine Operations and Controls

Traveling on Slopes

WARNING •

When traveling, raise the bucket approx. 20-30 cm (8-12”) from the ground.

•

Do not travel downhill in reverse.

•

Never turn on slopes or travel across slopes.

Always go down to a flat place to perform these operations. It may be longer, but it will ensure safety.

•

Always operate or travel in such a way that it is possible to stop safely at any time if the machine slips or becomes unstable.

•

Turning or operating the backhoe when working on slopes may cause the machine to lose its balance and turn over, so avoid such operations.

It is particularly dangerous to swing downhill when the bucket is loaded.

•

If such operations have to be carried out, pile soil to make a platform on the slope so that the machine can be kept horizontal when operating.

•

Do not travel up or down steep slopes. There is danger that the machine may turn over.

•

When traveling uphill, if the tracks slip or it is impossible to travel uphill using only the force of the tracks, do not use the pulling force of the arm to help the machine travel uphill. There is danger that the machine may turn over.

1. When traveling down steep hills, use the travel lever and fuel control lever to keep the travel speed low.

When traveling down a steep hill of more than 15°, set the backhoe to the position shown in the diagram on the right, and lower the engine speed.

Operation - 106

MX15 Operator’s Manual Machine Operations and Controls

REMARK Travel down hills with the sprocket (1) side down.

If the machine travels down with the sprocket (1) side up, the track tends to become loose, and that can cause the track to slip.

2. When traveling up a steep hill of more than 15°, set the backhoe to the position shown in the diagram on the right.

Traveling Downhill Put the travel lever in the neutral position. This will cause the brake to be automatically applied.

Engine Stopped on Slope If the engine stops when traveling uphill, move the travel levers to the neutral position, lower the bucket to the ground, stop the machine, then start the engine again.

Precautions on Slope •

Do not open or close the sliding door when traveling or operating on slopes. The operating effort may change suddenly.

•

Always keep the sliding door locked.

MX15 Operator’s Manual

Operation - 107

Machine Operations and Controls

Escape from Mud Always operate carefully to avoid getting stuck in mud. If the machine does get stuck in mud, do as follows to get the machine out.

Stuck One Side of Track NOTICE When using the boom or arm to raise the machine, always have the bottom of the bucket in contact with the ground. (Never push with the teeth.) The angle between the boom and arm should be 90° to 110°. The same applies when using the inverted bucket.

When only one side is stuck in mud, use the bucket to raise the track, then lay boards or logs and drive the machine out. If necessary, put a board under the bucket also.

Stuck Both Sides of Tracks If the track on both sides are in mud and the machine slips and cannot move, use the procedure given above to lay logs or timber. Dig the bucket into the ground at the front, operate the arm in the same way as when digging, and set the travel lever to FORWARD to pull the machine out.

Operation - 108

MX15 Operator’s Manual Machine Operations and Controls

Work Possible Using Compact Hydraulic Excavator In addition to the following, it is possible to further increase the range of applications by using various attachments.

Backhoe Work A backhoe is suitable for excavating at a position lower than the machine.

When condition of the machine is as shown in the diagram at right, each cylinder’s maximum pushing excavation force is obtained when the bucket cylinder and link, arm cylinder and arm are at 90°.

When excavating, use this angle effectively to optimize your work efficiency.

The range for excavating with the arm is from a 45° angle away from the machine to a 30° angle toward the machine.

There may be some differences depending on the digging depth, not try to keep within the above range rather than operating to the end of the cylinder stroke.

Ditching Work Ditching work can be performed efficiently by attaching a bucket which matches the digging operation and then setting the tracks parallel to the line of the ditch to be excavated.

To excavate a wide ditch, first dig both sides and then finally remove the center portion.

MX15 Operator’s Manual Machine Operations and Controls Loading Work In places where the swing angle is small, work efficiency can be enhanced by locating the dump truck in a place easily visible to the operator.

Loading dump trucks is easier and the loading capacity is greater if the hydraulic excavator loads from the rear of the dump truck rather than from the side.

Smoothing Work When refilling after excavation and when smoothing the ground surface, use the blade.

Side Ditching Work The machine can be used for side ditching in a confined worksite by combining the swing and boom swing operations.

Operation - 109

MX15 Operator’s Manual

Operation - 110

Machine Operations and Controls

Bucket Replacement

WARNING •

When pins are knocked in with a hammer, pieces of metal may fly and cause serious injury.

•

When carrying out this operation, always wear goggles, hard hat, gloves, and other protective equipment.

•

When the bucket is removed, place it in a stable condition.

•

If pins are hit with a strong force, there is a hazard that the pin may fly out and injure people in the surrounding area. Make sure that there is no one in the surrounding area before starting the operation.

•

When removing the pins, do not stand behind the bucket. In addition, be extremely careful not to put your foot under the bucket while standing at the side for the work.

•

When removing or inserting pins, be extremely careful not to get your fingers caught.

•

Never insert your fingers into the pin holes when aligning the holes.

NOTICE After removing the pins, make sure that mud or sand does not get on them. Dust seals are fitted at both ends of the bushings, so be careful not to damage them.

Stop the machine on a firm and flat surface and do the work. When performing joint work, appoint a conductor and follow that person's instructions and signals.

1. Place the bucket in contact with a flat surface.

REMARK When removing the pins, place the bucket so that it is in light contact with the ground. If the bucket is lowered strongly to the ground, the resistance will be increased and it will be difficult to remove the pins.

2. Remove the stopper bolts and nuts, then remove pins (A) and (B), and remove the bucket.

3. Align the arm with holes (1) and the link with holes (2), then coat with grease and install pins (A) and (B).

MX15 Operator’s Manual

Operation - 111

Machine Operations and Controls REMARK When installing the bucket, the O-rings are easily damaged, so fit the O-rings on the boss of the arm end as shown in the diagram. When knocking the pin, move the O-ring down to the regular groove.

4. Install the stopper bolts and nuts for each pin, then grease the pin.

Parking Machine

WARNING •

Avoid stopping suddenly. Give yourself ample room when stopping.

•

Park the machine on the firm, level ground. Avoid parking the machine on slopes. If it is unavoidably necessary to park the machine on a slope, put blocks under the tracks and dig the backhoe into the ground surface to stop the machine from moving.

•

If the control levers are touched by accident, the backhoe or machine may move suddenly, and this may lead to a serious accident. Before standing up from the operator's seat, always set the safety lock lever securely to the LOCK position.

1. Put the left and right travel levers (1) in the neutral position, then stop the machine.

Operation - 112

MX15 Operator’s Manual Machine Operations and Controls

2. Lower the engine speed to LOW IDLE by fuel control lever (2).

3. Lower the bucket horizontally until the bottom touches the ground.

4. Lower the blade to the ground.

5. Set safety lock lever (3) in the LOCK position.

MX15 Operator’s Manual Machine Operations and Controls

Machine Inspection After Daily Work Check the engine coolant temperature (1), engine oil pressure (2), and fuel level (3) on the machine monitor.

Locking Always lock the following places.

•

(1) Fuel tank filler port

•

(2) Engine hood

REMARK Use the starting switch key to open and close all these places.

Operation - 113

MX15 Operator’s Manual

Operation - 114

Machine Operations and Controls

Rubber Tracks Rubber Tracks Information Rubber tracks have excellent properties that are not found in steel tracks. However, if they are used in the same way as steel tracks, full use cannot be made of their advantages.

Be sure to operate without straining the rubber tracks in a way that matches the condition of the jobsite and the nature of the work.

Rubber Tracks Rubber track Little vibration

Excellent

Smooth travel (no creaks)

Excellent

Little noise

Excellent

No damage to paved surface

Excellent

Easy to handle

Excellent

Easily damage

Average

Strong drawbar pull

Excellent

Considering the properties of the material used, rubber tracks offer various advantages. However, their weak point is lack of strength. Therefore, it is important to understand the advantages of rubber tracks, and to follow the precautions regarding handling and prohibited work. This will extend the life of the rubber tracks and will enable the machine to display the advantages of rubber tracks to the maximum. Before using rubber tracks, always read “Using Rubber Tracks” on page 115.

Warranty For Rubber Tracks It is important to inspect and maintain the tracks at the correct tension. Furthermore, these tracks must not be used near objects where they are likely to suffer damage, such as the corners of steel plates, U-shaped ditch liners, blocks, on crushed rock or the sharp edges of rocks, iron beams, or scrap iron.

Any damage resulting from the customer's mistaken use of the machine shall not be included in the scope of the warranty.

MX15 Operator’s Manual

Operation - 115

Machine Operations and Controls Using Rubber Tracks Prohibited Works Do not carry out the following types of work.

•

Carrying out operations and steering on crushed rock, extremely rough hard rock, steel beams, scrap iron, or near the edges of steel plates will cause damage to the rubber tracks and turf-friendly tracks.

•

In places such as river beds where there are large numbers of large and small boulders, the stones may get caught and damage the rubber tracks or make the tracks come off. If dozing operations are carried out when the tracks are slipping, this will reduce the life of the rubber tracks.

•

Be careful not to get oil, fuel, or chemical solvent on the rubber tracks. If such a substance should get on the tracks, remove it immediately. Furthermore, do not travel on road surfaces where oil has collected.

•

When putting the machine into long-term storage (3 months or more), store the machine indoors where it is protected from direct sunlight or rain.

•

Do not use the machine in high-temperature areas, such as areas where there is burning wood, steel plates that have been left under the hot sun, or places where asphalt has been laid.

•

Do not move the machine with the crawler on one side raised using the backhoe. This will cause damage to the rubber tracks and may cause the rubber tracks to come off.

MX15 Operator’s Manual

Operation - 116

Machine Operations and Controls Long Life Operations Be careful of the following points when carrying out work.

•

Avoid carrying out counter-rotation turns on concrete surfaces. There is danger that the concrete surface will scrape off the rubber from the track.

•

Avoid making sudden changes in direction. This may cause premature wear or damage to the rubber tracks.

•

Avoid operating the steering when traveling over places where there is a big difference in height. When traveling over obstacles or places where there is a difference in height, drive the machine at right angles to the obstacle to prevent the tracks from coming off.

•

If the machine has been raised using the bucket, lower it slowly.

•

Avoid doing work with materials that produce oil when crushed (soy beans, corn, or remains of vegetables squeezed for oil), or wash the machine after use.

•

Avoid handling materials that will attack the adhesion of the steel core, such as salt, ammonium sulphate, potassium chloride, potassium sulphate, or calcium superphosphate; or wash the machine after use.

•

The adhesion of the core will be attacked by salt, so avoid using the machine in coastal areas.

•

When handling salt, sugar, wheat, or soy beans, if there is any deep cut in the rubber tracks, these substances may get into the lugs or cut portion of the rubber. Always repair the rubber before use.

•

Do not carry out work that involves scraping against walls or concrete embankments.

•

Rubber tracks slip extremely easily on snow or frozen roads. Be careful not to slip when traveling or working on slopes.

•

The properties of rubber tracks change when working in extremely cold places, and this will reduce the life of the rubber tracks.

•

Because of the properties of rubber, use the rubber tracks within a range of -25°C to +55°C (-13°F to +131°F).

•

When carrying out bucket operations, be careful not to damage the rubber tracks with the bucket.

MX15 Operator’s Manual

Operation - 117

Machine Operations and Controls Always maintain the rubber tracks at the proper tension to prevent them from coming off. If the tension is low, the rubber tracks will come off under the following conditions. Even if the tension is correct, be extremely careful when carrying out operations.

1. Avoid operating the steering when traveling over curbs, rocks, or places where there is a big difference in height (more than approx. 20 cm/8�).

When traveling over such objects, always travel at right angles to the object.

2. When traveling in reverse up a slope, do not turn when moving from flat ground onto the slope.

If it is necessary to turn on slopes, be sure to turn gradually.

3. Avoid traveling along the edge of slopes or on rough groundwith the track on one side raised (with the machine tilting at an angle of more than approx.

10°) and with the track on the other side on flat ground. To avoid damage to the rubber tracks, travel with the tracks on both sides on flat ground.

Operation - 118

MX15 Operator’s Manual Machine Operations and Controls

Mechanism of Track Shoe Coming Off Track 1. When traveling over an obstacle, a gap is formed between the track roller and the track shoe. In this condition, the track shoe may come off.

2. Furthermore, if the machine travels in reverse, a gap is formed between the track roller, idler, and track shoe.

Why Track Shoe Might Come Off Track •

When turning in a condition where the track shoe cannot move to the side because of the object it is passing over, or because of some other objec.

•

When the track shoe has moved out of alignment and the idler or track roller are not aligned with the core

MX15 Operator’s Manual Machine Operations and Controls •

If the machine travels in reverse in this condition, the track shoe will come off.

•

If the machine is turned in this condition, the track shoe will come off.

Operation - 119

MX15 Operator’s Manual

Operation - 120

Transportation

Transportation When transporting the machine, observe all related laws and regulations, and be careful to ensure safety.

As a basic rule, transport the machine by trailer. Select the trailer to match the weight and dimensions given in “Specifications” on page 189. Note that the value for the weight and transportation dimensions given in Specifications may differ according to the type of shoe or type of arm or other attachments.

Loading and Unloading with Trailer

WARNING •

When loading or unloading, always drive at low speed and do not operate the traveling accelerator pedal.

•

When loading or unloading, run the engine at low speed and operate slowly.

•

When loading or unloading the machine, park the trailer on a flat firm roadbed. Keep a fairly long distance between the road shoulder and the machine.

•

Use ramps with ample width, length, thickness, and strength and install them at a maximum slope of 15°. When using piled soil, compact the piled soil fully and prevent the slope face from collapsing.

•

Remove the mud from the undercarriage to prevent the machine from slipping to the side on the ramps.

Remove any water, snow, grease, oil, or other substances stuck to the ramps.

•

Never correct your steering on the ramps. There is danger that the machine may turn over. If necessary, drive off the ramps, correct the direction, then enter the ramps again.

•

It is dangerous to use the backhoe for the loading or unloading operation.

•

Never operate any lever other than the travel lever on the ramps.

•

The center of gravity of the machine will change suddenly at the joint between the ramps and the track or trailer, and there is a hazard of the machine losing its balance. Travel slowly over this point.

•

When swinging the upper structure on the trailer or truck, the machine is unstable, so pull in the backhoe and swing slowly.

•

Extend the track width before starting the operation.

MX15 Operator’s Manual

Operation - 121

Transportation When loading or unloading, always use ramps or a platform and carry out the operation as follows.

Loading 1. Perform loading and unloading on firm, level ground only. Maintain a safe distance from the edge of a road.

2. Properly apply the brakes on the trailer and put blocks under the tires to ensure that the trailer does not move.

•

Then fix the ramps in line with the centers of the trailer and the machine.

•

Be sure that the two sides are at the same level as one another.

•

Make the slope of the ramps a maximum of 15º.

•

Set the distance between the ramps to match the center of the tracks.

3.

Run the engine at low speed.

4. When loading, set the backhoe at the front and the blade at the rear, with the undercarriage and upper structure set parallel.

5. Align the direction of travel with the ramps and travel slowly.

•

Lower the backhoe as far as possible without causing interference.

•

When on the ramps, operate only the travel lever. Do not operate any other lever or pedal.

Operation - 122

MX15 Operator’s Manual Transportation

6. Do not operate the travel boost pedal.

7. Stop the machine at the specified place, then swing the upper structure slowly 180°.

8. Stop the machine at the specified position on the trailer.

MX15 Operator’s Manual

Operation - 123

Transportation Securing Machine

WARNING Load the machine on a level and hard place. Secure a sufficient distance between the road shoulder and the machine.

NOTICE To prevent damage to the bucket cylinder during transportation, fit a wooden block at one end of the bucket cylinder to prevent it from touching the floor.

After placing the machine on the specified position of the trailer, secure it according to the following procedure.

1. Lower the blade.

2. Extend the bucket and arm cylinders fully, then lower the boom slowly.

3. Stop the engine, then remove the key from the starting switch.

4. Lock each control lever with the safety lock lever securely.

5. Put blocks under both ends of the tracks to prevent the machine from moving during transportation, and tie the machine down securely with chains or wire rope of suitable strength.

Be particularly careful to fix the machine in position securely so that it does not slip to the side.

MX15 Operator’s Manual

Operation - 124

Transportation

Lifting Machine

WARNING •

Never raise the machine with any worker on it.

•

Always make sure that the wire rope used for lifting the machine is of ample strength for the weight of the machine.

•

Never lift the machine with the upper structure swung to the side. Swing the backhoe so that it is at the sprocket end and set the undercarriage and upper structure parallel before lifting.

•

When lifting, keep the machine horizontal.

•

Never go under the machine when it is raised.

•

Never try to lift the machine in any position other than the position given in the procedure below. There is a hazard that the machine may lose its balance.

•

Extend the variable blade and insert the pin securely.

NOTICE • For the details on the machine weight, see the section of “Specifications” on page 189.

•

The lifting procedure applies to machines with standard specifications.

•

The method of lifting differs according to the attachments and options actually installed. In such cases, please contact your Ditch Witch dealer for information.

When lifting the machine, carry out the operation on flat ground as follows.

1. Stop the engine, swing the upper structure so that the blade is at the rear of the machine (set the upper structure parallel to the track frame).

2. Raise the blade fully.

3. Extend the bucket cylinder and arm cylinder fully, operate the attachment control lever so that the boom cylinder is perpendicular to the ground, then set the safety lock lever to the LOCK position.

4. Set the boom swing pedal to the neutral position without swinging the boom at all, then set the pedal lock to the LOCK position.

5. Stop the engine and confirm that there is nothing around the operator’s seat, then get off the machine.

6. Extend the variable blade and insert the pin securely.

MX15 Operator’s Manual Transportation 7. Install shackles to the lifting holes (2 places) on both ends of the blade, then install the wire ropes.

8. Pass the wire rope through the bracket on the boom (see diagram on right).

NOTICE • Be sure to use the three brackets.

•

Do not lift the machine with the boom or the upper structure swung.

•

Be careful not to get the hoses caught.

9. Set the lifting angle of the wire rope to 30° to 40°, then lift the machine slowly.

10. After the machine comes off the ground, check the hook condition and the lifting position, and then lift slowly.

Operation - 125

MX15 Operator’s Manual

Operation - 126

Cold Weather Operation

Cold Weather Operation Cold Weather Operation Information If the temperature becomes low, it becomes difficult to start the engine, and the coolant may freeze, so do as follows.

Fuel and Lubricants Change to fuel and oil with low viscosity for all components. For details of the specified viscosity, see “Lubricants, Fuel, and Coolant Specifications” on page 148.

Cooling System Coolant

WARNING •

Coolant is toxic. Be careful not to get it into your eyes or on your skin. If it should get into your eyes or on your skin, wash it off with large amount of fresh water and see a doctor at once.

•

When changing the coolant or when handling coolant that has been drained when repairing the radiator, please contact your Ditch Witch dealer. Coolant is toxic, so do not let it flow into drainage ditches or spray it on to the ground surface.

•

Coolant is flammable, so do not bring any flame close. Do not smoke when handling coolant.

NOTICE • Never use methanol, ethanol, or propanol-based coolant.

•

Never use any water-leakage prevention agent or any coolant containing such an agent.

•

Do not mix different types of coolant.

For details of the coolant mixture when changing the coolant, see “Clean Inside of Cooling System” on page 159. Use a permanent coolant (ethylene glycol mixed with corrosion inhibitor, antifoam agent, etc.) meeting the standard requirements as shown below. With permanent coolant, no change of coolant is required for a year. If it is doubtful that an available coolant meets the standard requirements, ask the supplier of that coolant for information.

Standard requirements for permanent coolant •

SAE

J1034

•

FEDERAL STANDARD O-A-548D

REMARK In areas where permanent coolant is not available, it is possible to use coolant whose main component is ethylene glycol and does not contain any corrosion inhibitor. (Such coolant can be used for the winter season only.) However, in such a case, the coolant must be changed twice a year (spring and fall), so use permanent coolant as far as possible.

MX15 Operator’s Manual

Operation - 127

Cold Weather Operation Battery

WARNING •

The battery generates flammable gas, so do not bring fire or sparks near the battery.

•

Battery electrolyte is dangerous. If it gets in your eyes or on your skin, wash it off with a large amount of water and consult a doctor.

•

Battery electrolyte dissolves paint. If it gets on to the bodywork, wash it off immediately with water.

•

If the battery electrolyte is frozen, do not charge the battery or start the engine with a different power source. There is danger that the battery may explode.

When the ambient temperature drops, the capacity of the battery will also drop. If the battery charge ratio is low, the battery electrolyte may freeze. Maintain the battery charge as close as possible to 100%, and insulate it against cold temperature so that the machine can be started easily the next morning.

REMARK Measure the specific gravity and calculate the rate of charge from the following conversion table.

Temperature (°C) 20

Charging Rate(%)

0

-10

-20

100

1.28

1.29

1.30

1.31

90

1.26

1.27

1.28

1.29

80

1.24

1.25

1.26

1.27

75

1.23

1.24

1.25

1.26

•

As the battery capacity drops markedly in low temperatures, cover the battery or remove it from the machine, keep it in a warm place, and install it again the next morning.

•

If the electrolyte level is low, add distilled water in the morning before beginning work. Do not add the water after the day's work so as to prevent fluid in the battery from freezing in the night.

Operation - 128

MX15 Operator’s Manual Cold Weather Operation

After Daily Work Completion

WARNING •

Performing idle-running of the tracks is dangerous, so stay well away from the tracks.

•

After completion of operations, fill the fuel tank to prevent the formation of water caused by condensation of moisture in the empty space in the tank when the temperature goes down.

To prevent mud, water, or the undercarriage from freezing and making it impossible for the machine to move on the following morning, always observe the following precautions.

•

Remove all the mud and water from the machine body. In particular, wipe the hydraulic cylinder rod clean to prevent damage to the seal caused by mud or dirt on the rod surface getting inside the seal together with drops of water.

•

Park the machine on hard, dry ground. If this is impossible, park the machine on wooden boards. The boards help protect the tracks from being frozen in soil and the machine can start the next morning.

•

Open the drain valve and drain any water collected in the fuel system to prevent it from freezing.

•

After operation in water or mud, remove water from undercarriage as described below to extend undercarriage service life.

After Cold Weather Season When season changes and the weather becomes warmer, do as follows.

•

Replace the fuel and oil for all parts with oil of the viscosity specified. For details, see “Lubricants, Fuel, and Coolant Specifications” on page 148.

•

If for any reason permanent coolant cannot be used, and an ethyl glycol base coolant (winter, one season type) is used instead, or if no coolant is used, drain the cooling system completely, then clean out the inside of the cooling system thoroughly, and fill with fresh soft water.

MX15 Operator’s Manual

Operation - 129

Long-Term Storage

Long-Term Storage Before Storage NOTICE When storing the machine, set the machine in the position shown in the diagram on the right to protect the cylinder rod from rusting.

When putting the machine in storage for a long time, do as follows.

•

After every part is washed and dried, the machine shall be housed in a dry building. In case it is unavoidable to leave it outdoors, park the machine on flat ground free from flooding or other disaster and cover it with canvas.

•

Completely fill the fuel tank, lubricate and change the oil before storage.

•

Apply a thin coat of grease to the metal surface of the hydraulic piston rods.

•

Disconnect the negative terminals of the battery and cover it, or remove it from the machine and store it separately.

•

Lock each control lever and pedal with the safety lock lever and pedal lock.

•

Set the stop valve to the LOCK position on machines ready for attachments. Install the plugs to the elbows.

During Storage

WARNING If it is unavoidably necessary to carry out the rust-preventive operation while the machine is indoors, open the doors and windows to improve ventilation and prevent gas poisoning.

Operate the engine and move the machine for a short distance once a month so that a new film of oil will be coated over movable parts and component surfaces. At the same time, also charge the battery.

•

For machines equipped with an air conditioner, run the air conditioner.

•

Rotate the tracks.

Operation - 130

MX15 Operator’s Manual Long-Term Storage

After Storage NOTICE If the machine is to be used when the monthly rust prevention operation has not been carried out, please contact your Ditch Witch dealer.

When using the machine after long-term storage, do as follows before using it.

•

Wipe off the grease from the hydraulic cylinder rods.

•

Add oil and grease to all places.

•

When a machine is stored for a long period, moisture in the air will get into the oil. Check the oil before and after starting the engine. If there is water in the oil, change the oil.

MX15 Operator’s Manual

Operation - 131

Troubles and Actions

Troubles and Actions Running Out of Fuel When starting the engine after running out of fuel, fill with fuel and bleed the air from the fuel system before starting.

Phenomena That Are Not Failures Note that the following phenomena are not failures: •

When the arm is pulled in, the speed of movement will drop momentarily when the arm is more or less vertical.

•

The arm speed will drop momentarily when the bucket teeth are more or less horizontal.

•

When starting or stopping the swing, noise will be emitted from the brake valve.

•

When going down a steep slope at low speed, a noise will be emitted from the travel motor.

•

When the track width is set to CLOSE and the blade is operated, the gauge expands slightly.

•

When the blade is lowered and the track width is operated, the blade moves momentarily.

MX15 Operator’s Manual

Operation - 132

Troubles and Actions

Towing the Machine

WARNING •

When towing the machine, use a wire rope that has ample strength for the weight of the machine that is being towed.

•

Do not apply a sudden load to the wire rope.

If the machine sinks in mud and cannot get out under its own power, or if the drawbar pull of the excavator is being used to tow a heavy object, use a wire rope as shown in the diagram on the right.

Places pieces of wood between the wire ropes and the body to prevent the wire ropes from damaging the body.

Never use the hook for light-weight towing.

Severe Job Conditions •

When digging in water, if the water gets on to the backhoe mounting pins, add grease to bucket links (A), (B), (C), (D), and (E) for each operation.

•

When carrying out heavy duty digging and deep digging operations, add grease to bucket links (A), (B), (C), (D), and (E) (total: 6 points) before each operation.

After greasing, operate the bucket several times, then add grease again.

MX15 Operator’s Manual

Operation - 133

Troubles and Actions

Discharged Battery

WARNING •

It is dangerous to charge the battery while it is still mounted on the machine. Always remove the battery before charging it.

•

When checking or handling the battery, stop the engine and turn the starting switch key to the OFF position.

•

The battery generates hydrogen gas, so there is a hazard of explosion. Do not bring lighted cigarettes near the battery, or do anything that will cause sparks.

•

Battery electrolyte is diluted sulfuric acid, and it will attack your clothes and skin. If it gets on your clothes or on your skin, wash it immediately off with large amount of water. If it gets in your eyes, wash it out with fresh water, and consult a doctor.

•

When handling batteries, always wear protective goggles and rubber gloves.

•

When removing the battery, first disconnect the cable from the ground (normally the negative (-) terminal). When installing, install the positive (+) terminal first.

•

If a tool touches the positive terminal and the chassis, there is danger that it will cause a spark, so be extremely careful.

•

If the terminals are loose, there is danger that the defective contact may generate sparks that will cause an explosion.

•

When removing or installing the terminals, check which is the positive (+) terminal and which is the negative (-) terminal.

•

Corrosion around the terminals is a cause of self-discharge of the battery. Polish the terminals with sandpaper. After removing the rust, coat the terminals thinly with grease before installing.

Operation - 134

MX15 Operator’s Manual Troubles and Actions

Battery Removal and Installation NOTICE After securing the battery, check that it does not move. If it moves, tighten it again securely.

•

Before removing the battery, remove the ground cable (normally connected to the negative (-) terminal).

•

If any tool touches between the positive terminal and the chassis, there is a hazard of sparks being generated.

•

When installing the battery, connect the ground cable last.

•

When replacing the battery, fix the new battery securely in position with battery mounting clamp (2).

Tightening torque of mounting nut (2) Nut and clamp: 2.0 N•m (0.2 kg•m or 1.5 ft•lb).

Double nut: 27-34 N•m (2.8-3.5 kg•m or 19.9-25.1 ft•lb).

Battery Charging When charging the battery, if the battery is not handled correctly, there is a hazard that the battery may explode. Always follow the instructions of “Discharged Battery” on page 133 and the instruction manual accompanying the charger, and do as follows.

•

Set the voltage of the charger to match the voltage of the battery to be charged. If the voltage is not selected correctly, the charger may overheat and cause an explosion.

•

Connect the positive (+) charger clip of the charger to the positive (+) terminal of the battery, then connect the negative (-) charger clip of the charger to the negative (-) terminal of the battery. Be sure to fix the clips securely.

•

Set the charging current to 1/10 of the value of the rated battery capacity; when carrying out rapid charging, set it to less than the rated battery capacity.

If the charger current is too high, the electrolyte will leak or dry up, and this may cause the battery to catch fire and explode.

•

If the battery electrolyte is frozen, do not charge the battery or start the engine with a different power source. There is a hazard that this will ignite the battery electrolyte and cause the battery to explode.

•

Do not use or charge the battery if the battery electrolyte level is below the LOWER LEVEL line. This may cause an explosion. Always check the battery electrolyte level periodically and add distilled water to bring the electrolyte level to the UPPER LEVEL line.

MX15 Operator’s Manual

Operation - 135

Troubles and Actions Starting Engine with Jumper Cables When starting the engine with a jumper cable, do as follows: Connecting and Disconnecting Jumper Cables

WARNING •

When connecting the cables, never contact the positive (+) and negative (-) terminals.

•

When starting the engine with a jumper cable, always wear safety glasses.

•

Be careful not to let the normal machine and problem machine contact each other. This prevents sparks from generating near the battery which could ignite the hydrogen gas given off by the battery. If hydrogen gas explodes, it could cause serious injury.

•

Be careful not to make a mistake when connecting a jumper cable. In the last connection (to the upper structure frame), a spark will be caused, so connect the cable to a spot as far away from the battery as possible. (Avoid the backhoe, however, because it is not a good conductor)

•

When removing the jumper cable, exercise good care so that the jumper cable clips may not contact each other, or they contact the chassis.

NOTICE • The size of the jumper cable and clip should be suitable for the battery size.

•

The battery of the normal machine must be the same capacity as that of the engine to be started.

•

Check the cables and clips for damage or corrosion.

•

Make sure that the cables and clips are firmly connected.

•

Check that the safety lock levers and parking brake levers of both machines are in the LOCK position.

•

Check that each lever is in the NEUTRAL position.

MX15 Operator’s Manual

Operation - 136

Troubles and Actions Jumper Cable Connection Keep the starting switch at the OFF position.

Connect the jumper cable as follows, in the order of the numbers marked in the diagram.

1. Make sure that the starting switches of the normal machine and problem machine are both at the OFF position.

2. Connect one clip of jumper cable (A) to the positive (+) terminal of the problem machine.

3. Connect the other clip of jumper cable (A) to the positive (+) terminal of the normal machine.

4. Connect one clip of jumper cable (B) to the negative (-) terminal of the normal machine.

5. Connect the other clip of jumper cable (B) to the engine block of the problem machine.

Starting the Engine

CAUTION Always check that the safety lock lever is set to the LOCK position, regardless of whether the machine is working normally or has failed. Check also that all the control levers are at the HOLD or neutral position.

1. Make sure the clips are firmly connected to the battery terminals.

2. Start the engine of the normal machine and keep it running at high idle speed.

3. Turn the starting switch of the problem machine to the START position and start the engine. If the engine doesn’t start at first, try again after 2 minutes or so.

Jumper Cable Disconnection After the engine has started, disconnect the jumper cables in the reverse of the order in which they were connected.

1. Remove one clip of jumper cable (B) from the engine block of the problem machine.

2. Remove the other clip of jumper cable (B) from the negative (-) terminal of the normal machine.

3. Remove one clip of jumper cable (A) from the positive (+) terminal of the normal machine.

4. Remove the other clip of jumper cable (A) from the positive (+) terminal of the problem machine.

MX15 Operator’s Manual

Operation - 137

Troubles and Actions

Other Trouble Electrical System •

( ): Always contact your Ditch Witch dealer when dealing with these items.

•

In cases of abnormalities or causes which are not listed below, please contact your Ditch Witch dealer for repairs.

Problem

Main cause

Remedy

Lamp does not glow brightly even when the engine runs at high speed

•

Defective wiring

•

(Check, repair loose terminals, disconnections)

•

Defective adjustment of fan belt tension

•

Adjust fan belt tension For details, see EVERY 250 HOURS SERVICE

Charge level monitor does not go out even when engine is running

•

Defective alternator

•

(Replace)

•

Defective wiring

•

(Check, repair)

Abnormal noise is generated from alternator

•

Defective alternator

•

(Replace)

Starting motor does not turn when starting switch is turned to ON

•

Defective wiring

•

(Check, repair)

•

Insufficient battery charge

•

Charge

•

Defective starting motor

•

(Replace)

Starting motor pinion repeatedly moves in and out (makes rattling sound)

•

Insufficient battery charge

•

Charge

•

Defective safety relay

•

(Replace)

Starting motor turns engine sluggishly

•

Insufficient battery charge

•

Charge

•

Defective starting motor

•

(Replace)

Starting motor disengages before engine starts

•

Defective wiring

•

(Check, repair)

•

Insufficient battery charge

•

Charge

Pre-heating monitor does not light

•

Defective wiring

•

(Check, repair)

•

Defective monitor

•

(Replace)

Oil pressure monitor does not light up when engine is stopped (starting switch at ON position)

•

Defective monitor

•

(Replace)

•

Defective caution lamp switch

•

(Replace)

Lamp flickers while engine is running

MX15 Operator’s Manual

Operation - 138

Troubles and Actions Chassis •

( ): Always contact your Ditch Witch dealer when dealing with these items.

•

In cases of abnormalities or causes which are not listed below, please contact your Ditch Witch dealer for repairs.

Problem

Main cause

Remedy

Speed of travel, swing, boom, arm, bucket is slow

•

Lack of hydraulic oil

•

Add oil to specified level, see CHECK BEFORE STARTING

Pump generates abnormal noise

•

Clogged element in hydraulic tank strainer

•

Clean, see EVERY 2000 HOURS SERVICE

Excessive rise in hydraulic oil temperature

•

Lack of hydraulic oil

•

Add oil to specified level, see CHECK BEFORE STARTING

•

Dirty oil cooler

•

Clean, see EVERY 500 HOURS SERVICE

•

Loose fan belt

•

Adjust fan belt tension, see EVERY 250 HOURS SERVICE

•

Track too loose

•

Adjust track tension, see WHEN REQUIRED

Track comes off Abnormal wear of sprocket

MX15 Operator’s Manual

Operation - 139

Troubles and Actions Engine •

( ): Always contact your Ditch Witch dealer when dealing with these items.

•

In cases of abnormalities or causes which are not listed below, please contact your Ditch Witch dealer for repairs.

Problem

Main cause

Remedy

Engine oil pressure monitor lights up

•

Engine oil pan oil level is low (sucking in air)

•

Add oil specified level, see CHECK BEFORE STARTING

•

Clogged oil filter cartridge

•

Replace cartridge, see EVERY 250 HOURS SERVICE

•

Defective tightening of oil pipe joint, oil leakage from damaged part

•

(Check, repair)

•

Defective engine oil pressure sensor

•

(Replace sensor)

•

Defective monitor

•

(Replace)

•

Coolant level low, coolant leakage

•

Add coolant, repair, see CHECK BEFORE STARTING

•

Loose fan belt

•

Adjust fan belt tension, see EVERY 250 HOURS SERVICE

•

Dirt or scale accumulated in cooling system

•

Change coolant, clean inside of cooling system, see WHEN REQUIRED

•

Clogged radiator fin or damaged fin

•

Clean or repair, see EVERY 500 HOURS SERVICE

•

Defective thermostat

•

(Replace thermostat)

•

Loose radiator filler cap (high altitude operation)

•

Tighten cap or replace packing

•

Defective coolant level sensor

•

(Replace sensor)

Steam is emitted from top part of radiator (pressure valve)

Red range on engine coolant temperature gauge lights up

MX15 Operator’s Manual

Operation - 140

Troubles and Actions Problem

Main cause

Remedy

Engine does not start when starting motor is turned

•

Lack of fuel

•

Add fuel, see CHECK BEFORE STARTING

•

Air in fuel system

•

Repair place where air is sucked in, see EVERY 500 HOURS SERVICE

•

Defective fuel injection pump or nozzle

•

(Replace pump or nozzle)

•

Starting motor cracks engine sluggishly

•

See ELECTRICAL SYSTEM

•

Engine pre-heating monitor does not light up

•

See ELECTRICAL SYSTEM

•

Defective compression defective valve clearance

•

(Adjust valve clearance)

•

Too much oil in oil pan

•

Add oil specified level, see CHECK BEFORE STARTING

•

Improper fuel

•

Change to specified fuel

•

Clogged air cleaner element

•

Clean or replace, see WHEN REQUIRED

•

Defective nozzle

•

(Replace nozzle)

•

Defective compression

•

(See defective compression above)

Combustion noise occasionally makes breathing sound

•

Defective nozzle

•

(Replace nozzle)

Abnormal noise generated (combustion or mechanical)

•

Low grade fuel being used

•

Change to specified fuel

•

Overheating

•

See red range of engine coolant temperature gauge lights up as above

•

Damage inside muffler

•

Replace muffler

•

Excessive valve clearance

•

(Adjust valve clearance)

Exhaust gas is white or blue

Exhaust gas occasionally turns black

MX15 Operator’s Manual

Maintenance - 141

Maintenance Information

Maintenance 34

Maintenance Information Do not carry out any inspection and maintenance operation that is not found in this manual.

Service Meter Reading Check the service meter reading every day to see if the time has come for any necessary maintenance to be carried out.

Genuine Ditch Witch Replacement Parts Use genuine Ditch Witch replacement parts specified in the parts manual.

Genuine Lubricants Use specified oils and grease. Choose oils and grease with proper viscosities specified for ambient temperature.

Windshield Washer Fluid Use automobile window washer fluid and keep foreign materials out of it.

Fresh and Clean Lubricants Use clean oil and grease. Also, keep the containers of the oil and grease clean. Keep foreign materials away from oil and grease.

Check Drained Oil and Used Filter After oil is changed or filters are replaced, check the old oil and filters for metal particles and foreign materials. If large quantity of metal particles or foreign materials are found, always report to the person in charge and carry out suitable action.

Fuel Strainer If your machine is equipped with a fuel strainer, do not remove it while fueling.

Maintenance - 142

MX15 Operator’s Manual Maintenance Information

Welding Instructions •

Turn off the engine starting switch.

•

Do not apply more than 200V continuously.

•

Connect grounding cable within 1 m (3.3’) from the area to be welded. If grounding cable is connected near instruments, connectors, etc., the instruments may have troubles.

•

If a seal or bearing happen to come between the welding part and grounding point, change the grounding point to avoid such parts.

•

Do not use the area around the attachment pins or the hydraulic cylinders as the grounding point.

Do Not Drop Things Inside Machine •

When opening inspection windows or the oil filler port of the tank to carry out inspection, be careful not to drop nuts, bolts, or tools inside the machine.

If such things are dropped inside the machine, it will cause damage and malfunction of the machine and will lead to failure. If you drop anything inside the machine, always remove it immediately.

•

Do not put unnecessary things in your pockets. Carry only things which are necessary for inspection.

Dusty Jobsite When working at dusty worksites, do as follows: •

Inspect the air cleaner clogging monitor frequently to see if the air cleaner is clogged. Clean the air cleaner element at a shorter interval than specified.

•

Clean the radiator core frequently to avoid clogging.

•

Clean and replace the fuel filter frequently.

•

Clean electrical components, especially the starting motor and alternator, to avoid accumulation of dust.

•

When inspecting or changing the oil, move the machine to a place that is free of dust to prevent dirt from getting into the oil.

Avoid Mixing Lubricants If a different type of oil has to be added, drain the old oil and replace all the oil with the new type of oil.

Never mix different kinds of oil.

Locking the Inspection Covers If inspection or maintenance has to be carried out with the inspection cover open, lock it securely in position with the lock bar. If inspection or maintenance is carried out with the inspection cover not locked into position, there is a hazard that it may be suddenly blown shut by the wind and cause injury to the worker.

MX15 Operator’s Manual

Maintenance - 143

Maintenance Information Hydraulic System - Air Bleeding After repairing or replacing the hydraulic equipment or after removing the hydraulic hoses, it is necessary to bleed the air from the circuit. For details, see “Change Oil in Hydraulic Tank, Clean Strainer” on page 186.

Hydraulic Hose Installation •

When removing parts at locations where there are O-rings or gasket seals, clean the mounting surface and replace with new parts. When doing this, be careful not to forget to assemble the O-rings and gaskets.

•

When installing the hoses, do not twist them or bend them into loops with a small radius. This will cause damage to the hose and markedly reduce its service life.

Checks After Inspection and Maintenance Works If you forget carrying out the checks after inspection and maintenance, unexpected problems may occur, and this may lead to serious injury or property damage. Always do as follows.

Checks after operation (with engine stopped) •

Have any inspection and maintenance points been forgotten?

•

Have all inspection and maintenance items been carried out correctly?

•

Have any tools or parts been dropped inside the machine? It is particularly dangerous if parts are dropped inside the machine and get caught in the lever linkage mechanism.

•

Is there any leakage of coolant or oil? Have all the bolts been tightened?

Checks when operating engine •

For details of the checks when operating the engine, see “Two Workers for Maintenance When Engine is Running” on page 45 and pay careful attention to safety.

•

Are the inspection and maintenance items working properly?

•

Is there any leakage of fuel or oil when the engine speed is raised?

Selecting Fuel and Lubricants to Match Ambient Temperature It is necessary to use fuel and lubricants that match the ambient temperature. For details, see “Lubricants, Fuel, and Coolant Specifications” on page 148.

Maintenance - 144

MX15 Operator’s Manual Lubricants, Coolant, and Filters

Lubricants, Coolant, and Filters Handling Oil, Fuel, and Coolant Oil •

Oil is used in the engine and attachments under extremely severe conditions (high temperature, high pressure) and deteriorates with use.

Always use oil that matches the grade and temperature for use given in the operator’s manual.

Even if the oil is not dirty, always change the oil after the specified interval.

•

Oil corresponds to blood in the human body, so always be careful when handling it to prevent any impurities (water, metal particles, dirt, etc.) from getting in. The majority of problems with machines are caused by the entry of such impurities.

Take particular care not to let any impurities get in when storing or adding oil.

•

Never mix oils of different grades or brands.

•

Always add the specified amount of oil. Having too much oil or too little oil are both causes of problems.

•

If the oil in the attachment is not clear, there is probably water or air getting into the circuit. In such cases, please contact your Ditch Witch dealer.

•

When changing the oil, always replace the related filters at the same time.

•

At the time of shipping from the factory, SAE1OWCD is used for hydraulic type of oil. When HO46hydraulic oil is going to be used, change specified amount of oil (whole amount). The hydraulic oil that is not recommended by The Charles Machine Works, Inc. can cause clogging of oil filter, so do not use it. The portion of the oil that remains in the hoses or cylinders will not be a problem even though it will be mixed into new oil.

Fuel •

The fuel pump is a precision instrument, and if fuel containing water or dirt is used, it cannot work properly.

•

Be extremely careful not to let impurities get in when storing or adding fuel.

•

Always use the fuel specified in the operator’s manual.

Fuel may congeal depending on the temperature when it is used (particularly in low temperature below -15°C/5°F). It is necessary to change for the fuel that is suitable for the temperature.

•

To prevent the moisture in the air from condensing and forming water inside the fuel tank, always fill the fuel tank after completing the day's work.

•

Before starting the engine, or when 10 minutes have passed after adding fuel, drain the sediment and water from the fuel tank.

•

If the engine runs out of fuel, or if the filters have been replaced, it is necessary to bleed the air from the fuel system.

MX15 Operator’s Manual

Maintenance - 145

Lubricants, Coolant, and Filters Cooling System Coolant •

River water contains large amount of calcium and other impurities, so if it is used, scale will stick to the engine and radiator, and this will cause defective heat exchange and overheating.

•

Do not use water that is not suitable for drinking.

•

When using coolant, always observe the precautions given in the operator’s manual.

•

Ditch Witch machines are supplied with Komatsu original coolant when the machine is shipped. This coolant is effective in preventing corrosion of the cooling system. The coolant can be used continuously for two years or 4000 hours.

Coolant is flammable, so be extremely careful not to expose it to flame or fire.

•

The proportion of coolant to water differs according to the ambient temperature. For details of the mixing proportions, see “Clean Inside of Cooling System” on page 159.

•

If the engine overheats, wait for the engine to cool before adding coolant.

•

If the coolant level is low, it will cause overheating and will also cause problems with corrosion from the air in the coolant.

Grease •

Grease is used to prevent twisting and noise at the joints.

•

The zerks not included in this section are zerks used when overhauling, so they do not need grease. If any part becomes stiff or generates noise after being used for a long time, grease it.

•

Always wipe off all of the old grease that is pushed out when greasing. Be particularly careful to wipe off the old grease in places where sand or dirt sticking in the grease would cause wear of the rotating parts.

Oil and Fuel Storage •

Keep indoors to prevent any water, dirt, or other impurities from getting in.

•

When keeping drum cans for a long period, put the drum on its side so that the filler port of the drum can is at the side to prevent moisture from being sucked in.

If drum cans have to be stored outside, cover them with a waterproof sheet or take other measures to protect them.

•

To prevent any change in quality during long-term storage, be sure to use in the order of first in-first out (use the oldest oil or fuel first).

Maintenance - 146

MX15 Operator’s Manual Lubricants, Coolant, and Filters

Filters •

Filters are extremely important safety parts. They prevent impurities in the fuel and air circuits from entering important equipment and causing problems. Replace all filters periodically.

However, when working in severe conditions, replace the filters at shorter intervals according to the oil and fuel (sulfur content) being used.

•

Never try to clean the filters (cartridge type) and use them again. Always replace with new filters.

•

When replacing oil filters, check if any metal particles are affixed to the old filter. If any metal particles are found, please contact your Ditch Witch dealer.

•

Do not open packs of spare filters until just before they are to be used.

•

Always use genuine Ditch Witch filters.

Electric System Maintenance •

It is extremely dangerous if the electrical equipment becomes wet or the covering of the wiring is damaged. This will cause an electrical short and may lead to malfunction of the machine. Do not wash the inside of the operator's cab with water. When washing the machine, be careful not to let water get into the electrical components.

•

Service relating to the electric system is check of fan belt tension, check for damage or wear in the fan belt, and check battery fluid level.

•

Never install any electric components other than those specified by The Charles Machine Works, Inc.

•

External electro-magnetic interference may cause malfunction of the control system controller, so before installing a radio receiver or other wireless equipment, please contact your Ditch Witch dealer.

•

When working at the seashore, carefully clean the electric system to prevent corrosion.

•

When installing an operator's cab cooler or any other electrical equipment, connect it to an independent power source connector. The cables to supply power to the optional equipment must never be connected to the fuse, starting switch, or battery relay.

MX15 Operator’s Manual

Maintenance - 147

Lubricants, Coolant, and Filters

Handling Hydraulic System •

During and after operations, the hydraulic system is at high temperature. During operations, it is also under high pressure, so always pay careful attention to the following when carrying out inspection and maintenance of the hydraulic system.

•

Stop the machine on level ground, lower the bucket to the ground, and set so that there is no pressure on the cylinder circuit.

•

Always stop the engine.

•

Immediately after operations, the hydraulic oil and lubricating oil are under pressure and at high temperature, so always wait for the temperature to go down before starting maintenance.

•

Even when the temperature goes down, there may still internal pressure, so when loosening plugs, screws, or hose connections, do not stand directly in front, and loosen gradually to release the internal pressure before removing.

•

When carrying out inspection or maintenance of the hydraulic circuits, always bleed the air to release the internal pressure.

•

Inspection or maintenance consists of checking the hydraulic oil level, replacing the filters, and changing the hydraulic oil.

•

When removing high-pressure hoses, check that the O-ring is not damaged. If it is damaged, replace it.

MX15 Operator’s Manual

Maintenance - 148

Lubricants, Fuel, and Coolant Specifications

Lubricants, Fuel, and Coolant Specifications Proper Selection RESERVOIR

KIND OF FLUID

AMBIENT TEMPERATURE

CAPACITY Specified

ASTM D975 No. 1

Refill

4 liters 1.06 US gal

3 liters 0.79 US gal

0.33 liters 0.09 US gal

0.33 liters 0.09 US gal

24 liters 6.34 US gal

21 liters 4.62 US gal

19 liters 5.02 US gal

-

-

-

3.4 liters 0.90 US gal

-

MX15 Operator’s Manual

Maintenance - 149

Lubricants, Fuel, and Coolant Specifications REMARK • When fuel sulphur content is less than 0.5%, change oil in the oil pan according to every periodic maintenance hours described in this manual.

•

Change oil according to the following table if fuel sulphur content is above 0.5%.

Fuel sulphur content

Change interval of oil in engine oil pan

0.5 to 1.0%

1/2 of regular interval

Above 1.0%

1/4 of regular interval

•

When starting the engine with an ambient temperature of lower than 0°C (32°F), be sure to use engine oil of SAE10W, SAE10W-30 and SAE15W-40, even though the ambient temperature goes up to 10°C (50°F) more or less during the day.

•

Use API classification CD as engine oil and if API classification CC, reduce the engine oil change interval to half.

•

There is no problem if single grade oil is mixed with multigrade oil (SAE10W-30, 15W-40), but be sure to add single grade oil that matches the temperature range in the table.

•

We recommend oil which has been specifically formulated and approved for use in engine and hydraulic attachment applications.

•

Specified capacity: total amount of oil including oil for components and oil in hoses.

•

Refill capacity: amount of oil needed to refill system during normal inspection and maintenance.

ASTM: American Society of Testing and Material SAE: Society of Automotive Engineers API: American Petroleum Institute

MX15 Operator’s Manual

Maintenance - 150

Lubricants, Fuel, and Coolant Specifications

No.

Supplier

Engine Oil

Gear Oil

Grease

[CD or CE] SAE10W, 30, 40; 10W30, 15W40 (The 15W40 oil marked * is CE.)

[GL-4 or GL-5] SAE80, 90, 140

[Lithium-Base] NLGI No.2

Anti-freeze Coolant [Ethylene Glycol Base] Permanent Type

1

KOMATSU

EO10-CD EO30-CD EO10-30CD EO15-40CD

GO90 GO140

G2-LI G2-LI-S

2

AGIP

Diesel sigma S super diesel multigrade *Sigma turbo

Rotra MP

GR MU/EP

-

3

AMOCO

*Amoco 300

Multi-purpose gear oil

PYKON premium grease

-

4

ARCO

*Arcofleet S3 pius

Arco HD gear oil

Litholine HEP 2 Arco EP moly D

-

5

BP

Vanellus C3

Gear oil EP Hypogear EP

Energrease LS-EP2

coolant

6

CALTEX

*RPM delo 400 RPM delo 450

Universal thuban Universal thuban EP

Marfak all purpose 2 Ultra-duty grease 2

AF engine coolant

7

CASTROL

*Turbomax *RX super CRD

EP EPX Hypoy Hypoy B Hypoy C

MS3 Spheerol EPL2

Anti-freeze

8

CHEVRON

*Delo 400

Universal gear

Ultra-duty grease 2

-

9

CONOCO

*Fleet motor oil

Universal gear lubricant

Super-sta grease

-

10

ELF

Multiperformance 3C Performance 3C

11

EXXON (ESSO)

Essolube D3 *Essolube XD-3 *Essolube XD-3 Extra *Esso heavy duty Exxon heavy duty

12

GULF

13

-

AF-ACL AF-PTL AF-PT (Winter, one season type)

Tranself EP Tranself EP type 2

Glacelf

Gear oil GP Gear oil GX

Beacon EP2

All season coolant

Super duty motor oil *Super duty plus

Multi-purpose gear lubricant

Gulfcrown EP2 Gulfcrown EP special

Antifeeze and coolant

MOBIL

Delvac 1300 *Delvac super 10W-30, 15W-40

Mobilube GX Mobilube HD

Mobilux EP2 Mobilgease 77 Mobilgrease special

14

PENNZOIL

*Supreme duty fleet motor oil

Multi-purpose 4092 Multi-purpose 4140

Multi-purpose white grease 705 707L White-bearing grease

Anti-freeze and summer coolant

15

PETROFINE

FINA kappa TD

FINA potonic N FINA potonic NE

FINA marson EPL2

FINA tamidor

-

MX15 Operator’s Manual

Maintenance - 151

Lubricants, Fuel, and Coolant Specifications No.

Supplier

Engine Oil

Gear Oil

Grease

Anti-freeze Coolant

[CD or CE] SAE10W, 30, 40; 10W30, 15W40 (The 15W40 oil marked * is CE.)

[GL-4 or GL-5] SAE80, 90, 140

[Lithium-Base] NLGI No.2

Rimura X

Spirax EP Spirax heavy duty

Albania EP grease

Sunoco GL5 gear oil

Sunoco ultra prestige 2EP Sun prestige 742

Sunoco coolant and summer coolant

[Ethylene Glycol Base] Permanent Type

16

SHELL

17

SUN

18

TEXACO

*Ursa super plus Ursa premium

Multigear

Multifak EP2 Starplex 2

Coda 2055 startex coolant

19

TOTAL

Rubia S *Rubia X

Total EP Total Transmission TM

Multis EP2

Antigal/coolant

20

UNION

*Guardol

MP gear lube LS

Unoba EP

21

VEEDOL

*Turbostar *Diesel star MDC

Multigear Multigear B Multigear C

-

-

-

coolant

MX15 Operator’s Manual

Maintenance - 152

Tightening Torque Specifications

Tightening Torque Specifications Tightening Torque List

CAUTION •

If nuts, bolts, or other parts are not tightened to the specified torque, it will cause looseness or damage to the tightened parts, and this will cause failure of the machine or problems with operation.

•

Always pay careful attention when tightening parts.

Bolts Unless otherwise specified, tighten the metric nuts and bolts to the torque shown in the table below.

If it is necessary to replace any nut or bolt, always use a genuine Ditch Witch part of the same size as the part that was replaced.

Thread diameter of bolt (a) (mm)

Width across flats (b) (mm)

Tightening torque

N•m

kgf•m

lb•ft

N•m

kgf•m

lb•ft

6 8 10 12 14

10 13 17 19 22

13.2 31 66 113 177

1.35 3.2 6.7 11.5 18

9.8 23.1 48.5 83.2 130.2

11.8-14.7 27-34 59-74 98-123 157-196

1.2-1.5 2.8-3.5 6.0-7.5 10.0-12.5 16.0-20.0

8.7-10.8 20.3-25.3 43.4-54.2 72.3-90.4 115.7-144.7

16 18 20 22 24

24 27 30 32 36

279 382 549 745 927

28.5 39 56 76 94.5

206.1 282.1 405.0 549.7 683.5

245-309 343-425 490-608 662-829 824-1030

25.0-31.5 35.0-43.5 50.0-62.0 67.5-84.5 84.0-105.0

180.8-227.8 253.2-314.6 361.7-448.4 488.2-611.2 607.6-759.5

27 30 33 36 39

41 46 50 55 60

1320 1720 2210 2750 3280

135.0 175.0 225.0 280.0 335.0

976.5 1265.8 1627.4 2025.2 2423.1

1180-1470 1520-1910 1960-2450 2450-3040 2890-3630

120.0-150.0 155.0-195.0 200.0-250.0 250.0-310.0 295.0-370.0

868.0-1085.0 1121.1-1410.4 1446.6-1808.3 1808.3-2242.2 2133.7-2676.2

Target value

Service limit

MX15 Operator’s Manual

Maintenance - 153

Tightening Torque Specifications Hydraulic Hoses

Thread diameter of bolt (a) (mm)

Width across flats (b) (mm)

Tightening torque

N•m

kgf•m

lb•ft

N•m

kgf•m

lb•ft

10

14

14.7

1.5

10.8

12.7 - 16.7

1.3 - 1.7

9.4 - 12.3

14

19

29.4

3.0

21.7

27.5 - 39.2

2.8 - 4.0

20.3 - 28.9

18

24

78.5

8.0

57.9

58.8 - 98.1

6.0 - 10.0

43.4 - 72.3

22

27

117.7

12.0

86.6

88.3 - 137.3

9.0 - 14.0

65.1 - 101.3

24

32

147.1

15.0

108.5

117.7 - 176.5

12.0 - 18.0

86.8 - 130.2

30

36

215.7

22.0

159.1

176.5 - 245.2

18.0 - 25.0

130.2 - 180.8

33

41

255.0

26.0

188.1

215.7 - 284.4

22.0 - 29.0

159.1 - 209.8

Target value

Service limit

Maintenance - 154

MX15 Operator’s Manual Maintenance Schedule

Maintenance Schedule If the machine is equipped with a hydraulic breaker, the maintenance schedule for some parts will be different. For details, see “Maintenance Interval for Hydraulic Breaker” on page 155 to confirm the correct maintenance schedule when carrying out maintenance.

Initial 250 Hour Maintenance (Only After the First 250 Hours) 156 When Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156 •

Check, Clean and Replace Air Cleaner Element . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156

•

Clean Inside of Cooling System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159

•

Check Level of Battery Electrolyte . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .162

•

Clean Fuel Filter Element . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165

•

Check and Adjust Track Tension. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166

•

Check Rubber Tracks or Turf-Friendly Tracks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168

•

Replace Bucket Teeth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .171

•

Drain Water and Sediment from Fuel Tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .172

Checks Before Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173 Every 100 Hours Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . 173 •

Lubricating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173

Every 250 Hours Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . 175 •

Replace Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175

•

Check Oil Level in Final Drive Case, Add Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176

•

Replace Hydraulic Filter Element . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177

•

Check and Adjust Cooling Fan Belt Tension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179

MX15 Operator’s Manual

Maintenance - 155

Maintenance Schedule

Every 500 Hours Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . 180 •

Lubricating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180

•

Replace Engine Oil Filter Cartridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181

•

Replace Fuel Filter Element . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181

•

Clean and Inspect Radiator Fins and Oil Cooler Fins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183

•

Replace Fuel Feed Pump Pre-Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184

Every 1000 Hours Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . 185 •

Change Oil in Final Drive Case . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185

Every 2000 Hours Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . 186 •

Change Oil in Hydraulic Tank, Clean Strainer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 186

•

Check Alternator, Starting Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188

•

Check Engine Valve Clearances, Adjust . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188

Maintenance Interval for Hydraulic Breaker For machine equipped with a hydraulic breaker, the hydraulic oil deteriorates faster than for normal bucket digging operations, so set the maintenance intervals as follows.

•

Replace hydraulic filter element.

On a new machine, replace the element after the first 100 to 150 hours, then carry out further replacement of the element according to the table on the right.

•

Change oil in hydraulic tank.

Change the oil according to the table on the right.

MX15 Operator’s Manual

Maintenance - 156

Maintenance Procedure

Maintenance Procedure Initial 250 Hour Maintenance (Only After the First 250 Hours) Carry out the following maintenance only after the first 250 hours.

•

Replace fuel filter cartridge.

•

Replace engine oil filter cartridge.

•

Check engine valve clearance, adjust.

Special tools are needed for inspection and maintenance, so contact your Ditch Witch dealer.

For details of the method of replacing or maintaining, see “Every 500 Hours Maintenance” on page 180 and “Every 2000 Hours Maintenance” on page 186.

When Required Check, Clean, and Replace Air Cleaner Element

WARNING •

If inspection, cleaning, or maintenance is carried out with the engine running, dirt will get into the engine and the engine will suffer damage. Always stop the engine before carrying out these operations.

•

When using compressed air, there is danger that dirt may be blown around and cause serious injury.

Always use safety glasses, dust mask, and other protective equipment.

MX15 Operator’s Manual Maintenance Procedure Cleaning the Outer Element 1. Open the engine hood at the rear of the machine, loosen clip (1), and remove dust cup (2).

2. Throw away the dust inside dust cup (3) and clean the inside of the cup.

3. Take out element (3) and cover the air connector on the inside of the air cleaner body with a clean cloth or adhesive tape.

4. Clean interior of the air cleaner body.

5. Direct dry compressed air (max. 0.69 MPa (7 kgf/ cm2, 99.4 psi) from the inside of the outer element along its folds. Then blow with air along the folds from the outside, and finally blow again from the inside.

•

Replace an element which has been cleaned 6 times repeatedly or used throughout a year.

•

Replace element when the dust indicator red piston appears soon after installing the cleaned element even though it has not been cleaned 6 times.

Maintenance - 157

Maintenance - 158

MX15 Operator’s Manual Maintenance Procedure

6. If small holes or thinner parts are found on the element when it is checked by shining a light through it after cleaning, replace the element.

NOTICE • When cleaning the element, do not hit it or beat it against something.

•

Do not use an element whose folds or gasket or seal are damaged.

•

Wrap unused element and store it in a dry place.

7. Remove the cloth or adhesive tape used to cover the air connector inside the air cleaner body.

8. Set the cleaned element (4) in position.

9. Set dust cup with the arrow pointing up, then set it to the air cleaner body and secure it with clip.

10. Press the dust indicator button to return the red piston to its original position.

MX15 Operator’s Manual

Maintenance - 159

Maintenance Procedure Clean Inside of Cooling System

WARNING •

Immediately after the engine is stopped, the coolant is at a high temperature and the radiator is under high internal pressure. If the cap is removed to drain the coolant in this condition, there is a hazard of burns. Wait for the temperature to go down, then turn the cap slowly to release the pressure before removing it.

•

Cleaning is carried out with the engine running. When standing up or leaving the operator's seat, set the safety lock lever to the LOCK position.

•

For details of starting the engine, see “Before Starting Engine” on page 73 and “Starting Engine” on page 84.

•

There is danger of touching the fan if the undercover is left removed. Never enter behind the machine when the engine is running.

Clean the inside of the cooling system, change the coolant, and replace the corrosion resistor according to the table below.

Kind of coolant

Cleaning inside of cooling system and changing coolant

Adding corrosion resistor agent KI

Permanent type coolant (all season type)

Every year (autumn) or every 2000 hours, whichever comes first

Non-permanent type coolant containing ethylene glycol (winter, one season type)

Every 6 months (drain coolant in spring, add coolant in autumn)

Every 1000 hours and when cleaning the inside of the cooling system and when changing coolant

When not using coolant

Every 6 months or every 1000 hours, whichever comes first

Stop the machine on level ground when cleaning or changing the coolant.

Use a permanent type of coolant. If, for some reason, it is impossible to use permanent type coolant, use a coolant containing ethylene glycol.

Super Coolant (AF-ACL) has an anti-corrosion effect as well as an coolant effect.

The ratio of coolant to water depends on the ambient temperature, but to obtain the corrosion resistance effect, a minimum ratio of 30% by volume is necessary.

In areas where the water is hard, always add corrosion resistor agent KI. One packet of corrosion resistor agent contains 100 g (0.22 lb). The standard density of the mixture should be 7g/L (0.065 oz/gal).

MX15 Operator’s Manual

Maintenance - 160

Maintenance Procedure When deciding the ratio of coolant to water, check the lowest temperature in the past, and decide from the mixing rate table given below. It is actually better to estimate a temperature about 10°C (50°F) lower when deciding the mixing rate.

Mixing Rate of Water and Coolant Min. atmospheric temperature

°C

Above -10

-15

-20

-25

°F

Above 14

5

-4

-13

Amount of coolant

Amount of water

liters

1.1

1.2

1.4

1.6

gal

0.29

0.32

0.37

0.59

liters

2.3

2.2

2.0

1.8

gal

0.61

0.81

0.53

0.48

WARNING •

Coolant is flammable, so keep it away from flame.

•

Coolant is toxic. When removing the drain plug, be careful not to get water containing coolant on you.

If it gets in your eyes, flush your eyes with large amount of fresh water and see a doctor at once.

Use city water for the coolant. If river water, well water, or other such water supply must be used, contact your Ditch Witch dealer.

We recommend use of a coolant density gauge to control the mixing proportions.

•

Prepare a container to catch drained coolant with a minimum 5.6 L (1.48 gal) capacity.

•

Prepare a coolant inlet hose.

1. Remove 2 bolts (1) from the cover on the right side of the machine, then remove the cover above the radiator cap.

MX15 Operator’s Manual

Maintenance - 161

Maintenance Procedure 2. Check that the coolant temperature has gone down enough to make it possible to touch the radiator cap surface by hand, then turn radiator cap (2) slowly until it contacts the stopper to release the pressure.

3. Following this, push radiator cap (2) and turn it until it contacts the stopper. Remove cap.

4. Open the hood (3) at the rear of the machine.

5. Set container to catch the coolant under drain valve (4).

6. Open drain valve (4) to drain the coolant. Remove drain plug to drain the coolant.

7. After draining the coolant, close drain valve (4) and drain plug, and add coolant. When the radiator is full, start the engine and run at low idle. Raise the coolant temperature to above 90°C and run for approx. 10 minutes.

8. Stop the engine, then open drain valve (4) and remove the drain plug to drain the coolant.

9. After draining the coolant, clean the radiator with detergent. For the cleaning method, follow the instruction of detergent.

10. Close drain valve (4), wrap the drain plug with sealing tape, then close it.

11. Decide the proportions of coolant and water according to the table for the mixing rate of water and coolant.

12. After warming up the engine, check that each gauge and caution lamp are in normal condition. If any abnormality is found, carry out adjustment or repairs. Operate the machine under a light load until the engine coolant temperature gauge points to the white range (monitor panel spec.) or the green range (gauge panel spec.). To remove the air in the coolant, remove radiator cap and run the engine for 5 minutes at low idle, then for another 5 minutes at high idle.

Maintenance - 162

MX15 Operator’s Manual Maintenance Procedure

Check Level of Battery Electrolyte Carry out this check before operating the machine.

WARNING •

Do not use the battery if the battery electrolyte level is below the LOWER LEVEL line. This will accelerate deterioration of the inside of the battery and reduce the service life of the battery. In addition, it may also cause an explosion.

•

The battery generates flammable gas and there is danger of explosion, so do not bring fire or sparks near the battery.

•

Battery electrolyte is dangerous. If it gets in your eyes or on your skin, wash it off with a large amount of water and consult a doctor.

•

When adding distilled water to the battery, do not allow the battery electrolyte to go above the UPPER LEVEL line. If the electrolyte level is too high, it may leak and cause damage to the paint surface or corrode other parts.

NOTICE When adding distilled water in cold weather, add it before starting operations in the morning to prevent the electrolyte from freezing.

Inspect the battery electrolyte level at least once a month and follow the basic safety procedures given below.

Remove floor mat (1) and cover (2).

MX15 Operator’s Manual

Maintenance - 163

Maintenance Procedure When Checking Electrolyte Level from Side of Battery If it is possible to check the electrolyte level from the side of the battery, check as follows.

1. Open the cover at the right side of the machine.

2. Use a wet cloth to clean the area around the electrolyte level lines and check that the electrolyte level is between the UPPER LEVEL (U.L.) and LOWER LEVEL (L.L.) lines.

If the battery is wiped with a dry cloth, static electricity may cause a fire or explosion.

3. If the electrolyte level is below the midway point between the U.L. and L.L. lines, remove cap (1) and add distilled water to the U.L. line.

4. After adding distilled water, tighten cap (1) securely.

REMARK If distilled water is added to above the U.L. line, use a pipette to lower the level to the U.L. line.

Neutralize the removed fluid with baking soda (sodium bicarbonate), then flush it away with a large amount of water or consult your Ditch Witch dealer or battery maker.

Maintenance - 164

MX15 Operator’s Manual Maintenance Procedure

When It Is Impossible to Check Electrolyte Level from Side of Battery If it is impossible to check the electrolyte level from the side of the battery, or there is no display of the UPPER LEVEL line on the side of the battery, check as follows.

1. Open the cover at the right side of the machine.

2. Remove cap (1) at the top of the battery, look through the water filler port, and check the electrolyte surface. If the electrolyte does not reach the sleeve, add distilled water so that the level reaches the bottom of the sleeve (UPPER LEVEL line) without fail.

Use the diagram below for reference, and check if the electrolyte reaches the bottom of the sleeve.

3. After adding distilled water, tighten cap (1) securely.

REMARK If distilled water is added to above the bottom of the sleeve, use a pipette to lower the level to the bottom of the sleeve. Neutralize the removed fluid with baking soda (sodium bicarbonate), then flush it away with a large amount of water or consult your Ditch Witch dealer or battery maker.

When It Is Possible to Use Indicator to Check Electrolyte Level If it is possible to use and indicator to check the electrolyte level, follow the instructions given.

MX15 Operator’s Manual

Maintenance - 165

Maintenance Procedure Clean Fuel Filter Element (With water separator)

WARNING •

Engine is at high temperature immediately after the machine has been operated. Wait for engine to cool down before replacing the filter.

•

Do not bring fire or sparks near the fuel.

•

Prepare a filter wrench for fuel filter.

•

Prepare a container to catch the fuel.

1. Open the engine hood and set handle to the LOCK position. See “Engine Hood” on page 70.

2. Using a filter wrench, loosen ring (2), remove case (3), then throw out the water inside.

Be careful not to lose red ring (4) inside the case.

3. Wash element (5) and the inside of the case with diesel fuel.

4. Set case (3) in position, then tighten ring (2) to install.

5. Set handle (1) to the OPEN position.

MX15 Operator’s Manual

Maintenance - 166

Maintenance Procedure Check and Adjust Track Tension

WARNING •

The track tension is checked with the machine raised, so it is extremely dangerous if the machine comes down by mistake during the inspection. Stop the engine and set the safety lock lever to the LOCK position to prevent the machine from moving. Never put any part of your body under the track or track frame while measuring, and be extremely careful when taking the measurements.

•

For details of starting the engine and operating the work equipment, see “Before Starting Engine” on page 73, “Starting Engine” on page 84, “After Starting Engine” on page 88, and “Backhoe Controls and Operations” on page 99.

The wear of the rubber track will vary according to the working conditions and type of soil. Therefore, it is necessary to inspect the wear and track tension frequently.

In particular, after fitting new parts, be sure to carry out the first inspection after 30 hours of use.

Inspection 1. Move the machine to set the connection (M mark) of the track shoe at the top at a point midway between the sprocket and idler.

2. Raise the chassis with the boom and arm. When doing this, operate the levers slowly.

3. Measure the clearance between the bottom of the track frame and the top of the track shoe at a position that is safe even if the chassis should come down.

MX15 Operator’s Manual

Maintenance - 167

Maintenance Procedure 4. The standard clearance is 10-15 mm (0.40-0.60”) between the shoulder of the track shoe and the tread surface of the 2nd track roller from the sprocket.

If operations are carried out with the track shoe loose (when the clearance for the track tension is more than 20 mm/0.8”), it will cause the track to come off, and this will lead to premature wear of the core.

If the track tension is not at the standard value, adjust it in the following manner.

Adjustment

WARNING There is danger of plug (1) flying out under the high internal pressure of the grease. Never loosen plug (1) more than 1 turn.

Never loosen any part other than plug (1). Never put your face in the mounting direction of plug (1).

If the track tension cannot be loosened with the procedure given here, please contact your Ditch Witch dealer.

When Increasing Tension Prepare a grease gun.

1. Pump in grease through grease plug (1) with a grease gun.

2. To check that the tension is correct, move the machine slowly forward and backward.

3. Check the track tension again, and if the tension is not correct, adjust it again.

4. If the track tension is still loose after grease is pumped in, it may be necessary to replace the rubber track or replace the seal inside the cylinder. Please contact your Ditch Witch dealer for replacement.

MX15 Operator’s Manual

Maintenance - 168

Maintenance Procedure When Loosening Tension

WARNING It is extremely dangerous to release the grease by any method except the procedure given below.

If the track tension is not relieved by this procedure, contact your Ditch Witch dealer for repairs.

1. Loosen plug (1) gradually to release the grease.

2. Turn plug (1) a maximum of one turn.

3. If the grease does not come out smoothly, move the machine forward and backward a short distance.

4. Tighten plug (1).

5. To check that the tension is correct, move the machine slowly forward and backward.

6. Check the track tension again, and if the tension is not correct, adjust it again.

Check Rubber Tracks If the rubber tracks are in the following condition, they must be repaired or replaced, so please contact your Ditch Witch dealer for repairs or replacement.

Lug Height •

If lug height “a” is reduced by wear, the drawbar pull will drop.

If “a” is less than 5 mm (0.2”), replace with a new part.

MX15 Operator’s Manual Maintenance Procedure •

If the lug wears and the steel cord inside the shoe is exposed for two links or more, replace with a new part.

Rubber Track Steel Cord Cuts If more than half of the steel cord layer on one side is cut, replace with a new part.

Rubber Track Core Separations If the rubber core has separated at one place or more, replace with a new part.

Maintenance - 169

Maintenance - 170

MX15 Operator’s Manual Maintenance Procedure

Rubber Track Tension If the rubber track is still slack even when grease is pumped in, replace with a new part or replace the seal inside the cylinder.

If the track tension can only be increased to a level where the rubber track may come off, there may be not only elongation of the track shoe but also damage to the grease cylinder.

Rubber Track Cracks If the cracks between the rubber track lugs increase to a size of approx. 60 mm (2.36”) the track must be repaired. Even if the crack is small and short, if the steel cord can be seen inside, carry out repairs immediately.

If the length is less than 30 mm (1.18”) or the depth of the crack is less than 10 mm (0.39”), there is no particular need to carry out repairs.

When making judgement whether to replace, repair, or continue using rubber tracks, please contact your Ditch Witch dealer.

MX15 Operator’s Manual

Maintenance - 171

Maintenance Procedure Replace Bucket Teeth

WARNING •

It is dangerous if the attachment moves by mistake when the teeth are being replaced. Set the attachment in a stable condition, then stop the engine and set the safety lock lever securely to the LOCK position.

•

The pins can be knocked out only with strong force, so there is a hazard that the pin may fly out. Check that there is no one in the surrounding area.

•

There is a hazard that fragments will fly during the replacement work, so always wear protective equipment like safety glasses and gloves.

Replace the bucket teeth before the adapter starts to wear.

1. Set the bottom face of the bucket on a block, and stop the engine. Operate the control lever fully and check that the attachment is in a stable condition, then set the safety lock lever to the LOCK position.

Set so that the bottom face of the bucket is horizontal.

2. Place a bar on the head of pin (1), hit the bar with a hammer to knock out the pin, then remove tooth (2).

Maintenance - 172

MX15 Operator’s Manual Maintenance Procedure

3. Install a new tooth to the bucket.

Bolt tightening torque: 167 ± 20 N•m (17 ± 2 kgm, 123 ± 14 lb•ft) After operating for several hours, retighten the tooth mounting bolt.

Drain Water and Sediment from Fuel Tank NOTICE • Never use trichlene for washing the inside of the tank. Use diesel fuel only.

•

Carry out this procedure before operating the machine as a daily maintenance.

1. Carry out this procedure before operating the machine.

2. Prepare a container to catch the fuel that is drained.

3. Remove the floor mat (1) from the machine.

4. Open the drain valve (2) under the fuel tank on the right side of the machine and drain the sediment and water that has accumulated at the tank bottom together with fuel.

When doing this, be careful not to get fuel on yourself.

5. When only clean fuel comes out, close drain valve (2).

MX15 Operator’s Manual

Maintenance - 173

Maintenance Procedure

Check Before Starting For details of the following items, see “Checks Before Starting” on page 74 in the OPERATION section.

•

Check coolant level, add coolant

•

Check oil level in engine oil pan, add oil

•

Check fuel level, add fuel

•

Check oil level in hydraulic tank, add oil

•

Check electric wiring

•

Check function of horn

•

Check for water and sediment in water separator, drain water

Every 100 Hours Maintenance Lubricating NOTICE • For the first 100 hours on new machines where the parts are settling in, carry out greasing every ten hours.

•

After digging operations under water, be sure to grease the pins which were submerged.

1. Set the machine to the greasing position shown on the right diagram, lower the attachment to the ground, then stop the engine.

2. Using a grease pump, pump in grease through the grease fittings shown by arrows.

3. After greasing, wipe off any old grease that was pushed out.

(1) Swing pinion (1 point) When lubricating the swing pinion, turn the chassis little by little and apply grease through the grease fitting.

(2) Swing circle (1 point)

Maintenance - 174

MX15 Operator’s Manual Maintenance Procedure

(3) Bucket cylinder rod end (1 point) (4) Link coupling pin (1 point) (5) Bucket - Link coupling pin (1 point) (6) Arm - Bucket coupling pin (1 point) (7) Arm - Link coupling pin (1 point)

MX15 Operator’s Manual

Maintenance - 175

Maintenance Procedure

Every 250 Hours Maintenance Replace Engine Oil, Filter

WARNING The parts and oil are at high temperature immediately after the engine is stopped and may cause serious burns. Wait for the temperature to go down before starting the operation.

•

Engine oil catch pan capacity: 4 L (1.06 gal)

•

Refill capacity: 3 L (0.8 gal)

1. Set a container to catch the oil immediately under the drain plug (P) at the bottom of the machine.

2. Remove drain plug (P) slowly to avoid getting oil on yourself, and drain the oil.

3. Check the drained oil, and if there are excessive metal particles or foreign material, please contact your Ditch Witch dealer.

4. Install drain plug (P).

5. Using a filter wrench, turn filter cartridge (1) counterclockwise to remove it.

A large amount of oil will come out if this procedure is carried out immediately after stopping the engine, so wait for 10 minutes before starting the maintenance.

6. Clean the filter holder, fill the new filter cartridge with clean engine oil, coat the thread and packing surface of the new filter cartridge with clean engine oil (or coat it thinly with grease), then install it to the filter holder.

REMARK Confirm that no remnants of old packing still adhere to the filter holder as this may result in oil leakage. Check that there is no old packing affixed to the filter holder. If there is any old packing affixed to the filter, it will cause leakage of oil.

7. When installing, tighten until the packing surface contacts the seal surface of the filter holder, then tighten it up 1/2 to 3/4 of a turn.

8. After replacing the filter cartridge, add engine oil through oil filler (F) until the oil level is between the H and L marks on the dipstick (G).

9. Let the engine idle for a while, then stop the engine and confirm that the oil level is between the H and L lines according to “Check Oil Level in Engine Oil Pan, Add Oil” on page 75.

MX15 Operator’s Manual

Maintenance - 176

Maintenance Procedure Check Oil Level in Final Drive Case, Add Oil

WARNING •

The parts and oil are at high temperature immediately after the engine is stopped and may cause serious burns. Wait for the temperature to go down before starting the operation.

•

If there is still pressure remaining inside the case, the oil or plug may fly out. Loosen the plug slowly to release the pressure.

•

Prepare a container to catch drained oil.

•

Prepare a hexagon wrench.

1. Set so that drain plug (P) is at the bottom.

2. Set a container under plug (G) to catch the oil.

3. Remove level plug (G) with a hexagon wrench (width across flats: 8 mm). Oil level should be near the bottom of the plug hole.

4. If the oil level is still too low, add engine oil through the hole in plug (G) until the oil overflows.

5. After checking, install plug (G).

MX15 Operator’s Manual

Maintenance - 177

Maintenance Procedure Replace Hydraulic Filter Element

WARNING •

The parts and oil are at high temperature after the engine is stopped and may cause serious burns.

Wait for the temperature to go down before cleaning the hydraulic tank strainer.

•

When the oil filler cap is removed, oil may spurt out, so turn the cap slowly to release the pressure before removing the cap.

NOTICE If the machine is equipped with a hydraulic breaker, the hydraulic oil will deteriorate much faster than during normal bucket operations. For details, see “Maintenance Interval for Hydraulic Breaker” on page 155 when carrying out maintenance.

•

Prepare a filter wrench for hydraulic filter cartridge.

1. Tip the operator's seat and remove the toolbox from under the seat. For details, see “Tipping Operator’s Seat” on page 72.

2. Remove cover at the left side of the machine.

3. Remove the cap from oil filler (F), and release the internal pressure.

4. Loosen the clamp of hose (1), then loosen 4 bolts.

5. Take out element assembly (2).

6. Using a filter wrench, turn filter cartridge (3) to the left to remove it.

7. Clean the filter holder, then coat of the seal surface of the new filter cartridge with engine oil (or coat it thinly with grease).

8. When installing, bring the packing surface into contact with the seal surface of the filter holder, then tighten a further 1/2 - 3/4 turns.

Maintenance - 178

MX15 Operator’s Manual Maintenance Procedure

NOTICE Be sure to pressurize the hydraulic tank. If it is not pressurized, the pump will suck in air, and this will adversely affect equipment.

9. Leave hydraulic tank cap (F) removed, and extend the boom, arm, and bucket cylinders fully as shown in the diagram on the right. Then install the cap and pressurize the inside of the tank.

10. Install cover.

MX15 Operator’s Manual

Maintenance - 179

Maintenance Procedure Check and Adjust Cooling Fan Belt Tension Checking The deflection should be 10-15 mm (0.4-0.6”) when the belt is pressed at a point midway between the alternator pulley and fan pulley (A) with a pressure of approx. 58.8 N (6 kgm, 13.2 lb).

Adjustment •

Prepare a pinch bar.

•

Prepare a wooden block.

1. Tip the operator's seat over to the front, then remove the toolbox from under the seat. For details, see “Tipping Operator’s Seat” on page 72.

2. Remove 4 bolts (4) from the panel under the operator's seat, then remove the cover.

3. Insert a bar between alternator (1) and the cylinder block to fix alternator (1) in position. When fixing alternator (1) in position, insert a wooden block between the bar and alternator (1) to prevent damage to the alternator.

4. Loosen bolts and nuts (2), (3) and (4).

5. Move alternator (1) with a bar so that the deflection of the belt is 10-15 mm (0.4-0.6”) (approx. 6 kg/13 lb).

6. Tighten the bolts and nuts (2), (3) and (4) to fix alternator (1) in position.

7. Check each pulley for damage, wear of the V-groove, and wear of the V-belt. In particular, be sure to check that the V-belt is not touching the bottom the V-groove.

8. If the belt is stretched, leaving no allowance for adjustment, or if it is cut or cracked, contact your Ditch Witch dealer for replacement.

Maintenance - 180

MX15 Operator’s Manual Maintenance Procedure

Every 500 Hours Maintenance Maintenance for every 100 and 250 hours should be carried out at the same time.

Lubricating 1. Set the machine to the greasing position shown on the right, lower the backhoe to the ground, then stop the engine.

2. Using a grease pump, pump in grease through the grease fittings shown by arrows.

3. After greasing, wipe off any old grease that was pushed out.

(1) Boom cylinder foot pin (1 point) (2) Boom swing bracket pin (2 points) (3) Boom foot pin (2 points)

(4) Arm cylinder foot pin (1 point) (5) Boom cylinder rod end (1 point) (6) Arm cylinder rod end (1 point) (7) Boom - Arm coupling pin (1 point) (8) Bucket cylinder foot pin (1 point)

MX15 Operator’s Manual

Maintenance - 181

Maintenance Procedure Replace Fuel Filter Element (With water separator)

WARNING •

Engine is at high temperature immediately after the machine has been operated. Wait for engine to cool down before replacing the filter.

•

Do not bring fire or sparks near the fuel.

•

Prepare a filter wrench for fuel filter element.

•

Prepare a container to catch the fuel.

1. Set the container to catch the fuel under the filter element and element cup.

2. Close valve (1) at the top of the filter.

3. Using a filter wrench, turn filter element cup (2) counterclockwise to remove it.

4. Clean the filter holder, fill the new filter element cup with fuel, coat the packing surface with engine oil, then install it to the filter holder.

5. When installing, tighten until the packing surface comes into contact with the seal surface, then tighten approx. 2/3 turn.

NOTICE If the filter element cup is tightened too far, the packing will be damaged and this will lead to leakage of fuel. If the filter element cup is too loose, fuel will also leak from the packing, so always tighten to the correct amount.

6. Set fuel control lever to the low idle position.

7. After replacing the fuel filter element, bleed the air.

For details of the procedure, see the section on bleeding the air on the next page.

8. After replacing the filter element, start the engine and check that there is no leakage of fuel from the filter seal surface. If there is any leakage of fuel, check the tightening of the filter element cup. If there is still leakage of fuel, follow Steps 1 and 3 to remove the filter element cup, then check the packing surface for damage or foreign material. If any damage or foreign material is found in the packing, replace the packing with a new part, then repeat Steps 4 to 7.

Maintenance - 182

MX15 Operator’s Manual Maintenance Procedure

Air Bleeding 1. Fill the fuel tank with fuel until fuel gauge (G) indicates F.

2. Turn and keep the starting switch key at the ON position for 10 to 20 seconds. Air is automatically bled by the automatic air bleeding device.

3. Turn the starting key to the START position to start the engine.

REMARK This air bleeding procedure can also be applied when the fuel has run out.

MX15 Operator’s Manual

Maintenance - 183

Maintenance Procedure Clean and Inspect Radiator Fins

WARNING If compressed air, high-pressure water, or steam hit your body directly, or they cause dirt or dust to be blown up, there is a hazard of serious injury. Always use safety glasses, dust mask, or other protective equipment.

NOTICE • When using compressed air, if the nozzle is brought too near the fins, the fins may be damaged. Carry out the cleaning from a reasonable distance to prevent damage to the fins.

•

Do not direct the jet directly at the core. If the fins are damaged, it will cause leakage of water and overheating. On dusty jobsites, carry out this inspection every day, regardless of the maintenance interval.

1. Remove 3 bolts (1), then remove the grill on the right side of the machine.

2. Use compressed air to blow off the mud, dirt, or leaves clogging radiator fins (1).

MX15 Operator’s Manual

Maintenance - 184

Maintenance Procedure Replace Fuel Feed Pump Pre-Filter

WARNING •

Do not replace the pre-filter just after stopping the engine, since each part is still hot. Wait until each part has cooled down.

•

After replacing the pre-filter, connect the fuel hoses securely so that fuel will not leak.

•

Do not bring fire or spark near the pre-filter.

Prepare a container to catch the fuel.

1. Set the container to catch the fuel under the prefilter (1).

2. Set the fuel control lever to the low idle position.

3. Remove pre-filter (1) from the clamp (2).

4. Loosen clamps (3) and remove fuel hoses (4) from pre-filter (1).

5. Connect fuel hoses (4) to new pre-filter (1), then secure them with clamps (3).

6. Install pre-filter (1) to clamp (2).

7. After replacing the pre-filter, bleed air. For the air bleeding procedure, see “Replace Fuel Filter Element” on page 181.

MX15 Operator’s Manual

Maintenance - 185

Maintenance Procedure

Every 1000 Hours Maintenance Maintenance for every 100, 250 and 500 hours should be carried out at the same time.

Change Oil in Final Drive Case

WARNING •

The parts and oil are at high temperature immediately after the engine is stopped, and may cause serious burns. Wait for the temperature to go down before starting the operation.

•

If there is still pressure remaining inside the case, the oil or plug may fly out. Loosen the plug slowly to release the pressure.

•

Container to catch drained oil: Min. 0.5 L (0.13 gal) capacity

•

Refill capacity: 0.33 L (0.09 gal)

•

Prepare a hexagon wrench; drain plug is 8 mm (0.315”)

1. Set so that drain plug (2) is at the bottom.

2. Set the container to catch the drained oil under drain plug (2).

3. Remove LEVEL plug (1) and DRAIN plug (2) with hexagonal wrench to drain the oil.

4. Tighten drain plug (2).

5. Add oil through the hole of LEVEL plug (1) up to the specified level.

6. When oil flows out from the hole of level plug (1), install level plug (1).

MX15 Operator’s Manual

Maintenance - 186

Maintenance Procedure

Every 2000 Hours Maintenance Maintenance for every 100, 250, 500 and 1000 hours should be carried out at the same time.

Change Oil in Hydraulic Tank, Clean Strainer

WARNING When the oil filler cap is removed, oil may spurt out, so turn the cap slowly to release the pressure before removing the cap.

•

Container to catch drain oil: min. 23 L (6.08 gal) capacity

•

Refill capacity: 21 L (5.54 gal)

•

Prepare a handle (for the socket wrench).

1. Swing the upper structure so that the drain plug under the hydraulic tank will be between both tracks.

2. Retract the arm and bucket cylinders, then lower the boom and put the teeth in contact with the ground.

3. Lower the blade to the ground.

4. Set the safety lock lever to the LOCK position and stop the engine.

MX15 Operator’s Manual Maintenance Procedure 5. Tip the operator’s seat over to the front, then remove the toolbox from under the seat. For details, see “Tipping Operator’s Seat” on page 72.

Use the tool to remove the cap from oil filler (F).

6. Remove 3 bolts (1) under the rear left of the machine, then remove the cover of the drain plug.

7. Set the oil container under the drain plug under the machine. Using the handle, remove drain plug (P) and drain the oil. Check the O-ring installed to plug (P), and if it is damaged, replace the O-ring. After draining the oil, tighten drain plug (P).

Tightening torque: 68.6 ± 9.81N•m (7 ± 1kgm, 50.6 ± 7.2 ft•lb) Take care not to get oil on yourself when you remove drain plug (P).

8. Loosen hose clamp (2) and remove hose (3).

Remove bolt (4) and strainer (5).

9. Remove any dirt stuck to strainer (5), then wash it in clean diesel oil or flushing oil. If strainer (5) is damaged, replace it with a new part.

10. Secure strainer (5) with bolt (4), and insert and secure hose (3) with hose clamp (2).

11. Add the specified amount of new and clean engine oil (for hydraulic system) through oil filler port (F).

Check that the oil level is between H and L on the sight gauge.

Maintenance - 187

Maintenance - 188

MX15 Operator’s Manual Maintenance Procedure

12. Extend the boom, arm, and bucket cylinder fully as shown in the diagram on the right, remove the oil filler cap, then install the cap and pressurize the inside of the tank.

NOTICE Be sure to pressurize the hydraulic tank. If it is not pressurized, the pump will suck in air, and this will adversely affect the equipment.

13. After replacing the oil, set each control lever to the neutral position and run the engine idle at a low speed for 2 to 3 minutes, then start the normal work.

Check Alternator, Starting Motor The brush may be worn or the bearing may have run out of grease. Contact your Ditch Witch dealer for inspection or repair.

If the engine is started frequently, carry out inspection every 1000 hours.

Check Engine Valve Clearance, Adjust As special tool is required for removing and adjusting the parts, contact your Ditch Witch dealer for service.

MX15 Operator’s Manual

Specifications - 189

Specifications

General

Metric

U.S.

Operating weight

1,590 kg

3,506 lb

Bucket capacity

0.044 m3

0.05 yd3

Name of engine

Komatsu 3D68EK-3K diesel engine

Engine power

11.2 kW @ 2600 rpm

15 hp @ 2600 rpm

A

Overall length

3.6 m

11 ft 9 in

B

Overall height

2.4 m

7 ft 12 in

C

Overall width

1 - 1.3 m

3 ft 3 in - 4 ft 1 in

D

Track width

230 mm

9 in

E

Tail swing radius

790 mm

2 ft 7 in

F

Length of track

1.6 m

5 ft 1 in

G

Tumbler center distance

1.2 m

3 ft 12 in

Min. ground clearance

205 mm

8 in

Low

2.3 km/h

1.4 mph

High

4.3 km/h

2.7 mph

Swing speed

8.3 rpm

8.3 rpm

Travel speed

MX15 Operator’s Manual

Specifications - 190

Working Ranges

Metric

U.S.

A

Max. digging reach

3.9 m

12 ft 9 in

B

Max. digging depth

2.2 m

7 ft 1 in

C

Max. digging height

3.5 m

11 ft 7 in

D

Max. vertical wall depth

1.8 m

5 ft 9 in

E

Max. dumping height

2.6 m

8 ft 4 in

F

Max. reach at ground level

3.8 m

12 ft 5 in

G

Max. blade lifting height

280 mm

11 in

H

Max. blade lowering depth

155 mm

6 in

MX15 Operator’s Manual

Attachments and Options - 191

Attachments and Options Chapter Contents General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192 •

Safety First . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192

•

Attachment Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 194

Bucket with Hook . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195 •

Hook Condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195

•

Prohibited Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .195

Machine Ready for Attachment . . . . . . . . . . . . . . . . . . . . . . . . . 196 •

Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196

•

Hydraulic Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 198

•

Attachment Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .200

Attachment Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 202 •

Attachment Combinations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .202

•

Hydraulic Breaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 204 46

Attachments and Options - 192

MX15 Operator’s Manual General Information

General Information Safety First If attachments or options other than those authorized by The Charles Machine Works, Inc. are installed, this will not only affect the life of the machine, but will also cause problems with safety.

When installing attachments not listed in this operator’s manual, contact your Ditch Witch dealer first.

If you do not contact your Ditch Witch dealer, we cannot accept any responsibility for any accidents or failures.

WARNING General Precautions •

Read the instruction manual for the attachment thoroughly, and do not use this attachment unless you are sure that you have understood the guide completely.

•

If you lose the instruction manual, always ask the manufacturer or your Ditch Witch dealer for a new copy.

•

Depending on the attachment, install the necessary front guard to the machine.

•

Depending on the attachment, the impact noise may make it difficult for fellow workers to transmit instructions for the operation. Before starting operation, designate a leader and determine the signals to be used.

•

Do not carry out swinging operations to the side with a heavy load on the attachment. This is particularly dangerous on slopes.

•

Compared with a machine equipped with a bucket, a machine equipped with a breaker has a heavy load at the front of the attachment and is unstable. To avoid a hazard of tipping over, do not carry out operations with the attachment swung to the side.

•

When an attachment is installed, the swing range and center of gravity of the machine are different, and the machine may move in an unexpected way. Be sure that you understand the condition of the machine properly.

•

Before starting operations, set up a fence around the machine to prevent people from entering. Never operate the machine when there are people near the machine.

•

To prevent serious accidents caused by misoperation, do not put your foot on the pedal except when operating the pedal.

MX15 Operator’s Manual

Attachments and Options - 193

General Information

WARNING Precautions for Removal and Installation Operations When removing or installing the attachments, obey the following precautions and take care to ensure safety during the operation.

•

Carry out the removal and installation operation on a flat, firm ground surface.

•

When the operation is carried out by two or more workers, determine the signals and follow these during the operation.

•

When carrying heavy objects (more than 25 kg or 55 lb), use a crane.

•

When removing heavy parts, always support the part before removing it.

•

When lifting heavy parts with a crane, always pay careful attention to the position of the center of gravity.

•

It is dangerous to carry out operations with the load kept suspended. Always set the load on a stand, and check that it is safe.

•

When removing or installing attachments, make sure that it is in a stable condition and will not fall over.

•

Never go under a load suspended from a crane. Always stand in a position that is safe even if the load should fall.

NOTICE • Qualifications are required to operate a crane. Never allow the crane to be operated by an unqualified person.

•

For details of removal and installation operations, contact your Ditch Witch dealer.

MX15 Operator’s Manual

Attachments and Options - 194

General Information

Attachment Installation

WARNING Long or heavy attachments cause the machine to have poor stability, so there is danger of the machine losing its balance and tipping over when traveling down steep hills or when swinging on slopes.

Never do any of the following. They are extremely dangerous.

•

Traveling downhill with the attachment raised

•

Traveling across slopes

•

Swinging upper structure on slopes

•

If heavy-load attachment is installed, there will be excessive overrun when swinging (the distance from operating to stop the swing to the point where the swing stops completely), so there is danger of mistaking the distance and hitting other objects.

Allow a margin to the stopping point when operating.

In addition, the hydraulic drift (the gradual downward movement caused by the weight of the attachment when the attachment is stopped in a raised condition) will also increase.

•

If the correct procedure is not used when installing the boom and arm, it may lead to serious damage.

Please consult your Ditch Witch dealer.

•

When long attachment is installed, the working range will suddenly become larger, so there is danger of mistaking the distance and hitting other objects. Allow an ample margin between the attachment and surrounding obstacles when operating.

MX15 Operator’s Manual

Attachments and Options - 195

Bucket with Hook

Bucket with Hook Hook Condition Check that there is no damage to the hook, stopper, or hook mount. If there is any abnormality, contact your Ditch Witch dealer.

Prohibited Operations Precautions During Operation •

When carrying out lifting operations, reduce the engine speed and use the lifting operation mode.

•

Depending on the operating posture, there is danger that the wire or ring may come off the hook.

To prevent this, pay careful attention to the angle of the hook.

•

Never drive the machine while lifting a load.

•

If the bucket with hook is turned and used for operations, it will hit the arm during dumping operations, so be careful when using it.

•

If you are planning to newly install a hook, contact your Ditch Witch dealer.

Attachments and Options - 196

MX15 Operator’s Manual Machine Ready for Attachment

Machine Ready for Attachment Locations

Stop Valve This valve (1) stops the flow of the hydraulic oil.

•

Position (a): Hydraulic oil stops.

•

Position (b): Hydraulic oil flows.

When removing or installing attachments, set this valve to the position (a).

Width A: 19 mm (0.7”)

MX15 Operator’s Manual Machine Ready for Attachment Selector Valve This valve (2) switches the flow of the hydraulic oil.

•

Position (1): When breaker is used.

•

Position (2): When general attachment (crusher, etc.) is used.

Attachment Control Pedal This pedal (3) is used to operate the attachment.

REMARK When depressing the rear of the pedal (mainly when operating the breaker), put the tip of your foot on plate (1) at the bottom left of the handrail and depress the pedal with your heel. This makes it possible to operate the pedal smoothly.

Attachments and Options - 197

Attachments and Options - 198

MX15 Operator’s Manual Machine Ready for Attachment

Hydraulic Circuit Hydraulic Circuit Connection When connecting the attachment, connect the hydraulic circuit as follows.

1. Check that the stop valve is at the LOCK position, then remove the plug.

Be careful not to lose or damage any part that is removed.

2. Connect the elbow and zerk provided by the attachment maker, then connect the attachment hydraulic hoses.

NOTICE When connecting the hydraulic hoses, operate the bucket fully to the dump position and be careful not to interfere with link (a).

MX15 Operator’s Manual

Attachments and Options - 199

Machine Ready for Attachment Bleeding Air 1. Starting engine Start the engine according to “Starting Engine” on page 84, keep running the engine at low idle for 10 minutes, and carry out the following procedure.

2. Bleeding air from cylinders •

Run the engine at low idle and partially extend and retract each cylinder 4 to 5 times (stop approx.

100 mm (4 in) before the end of the stroke).

•

Next, operate each cylinder to the end of its stroke 3-4 times.

NOTICE If, at first, the engine is run at high speed or the cylinder is operated to the end of its stroke, the air inside the cylinder may cause damage to the piston packing or other parts.

3. Bleeding air from attachment (if equipped) For machine equipped with attachment such as the breaker, actuate the attachment pedal about 10 times to bleed the air completely from the attachment circuit while running the engine at low idle.

NOTICE If the attachment bleeding procedure is specified by the manufacturer, bleed the attachment according to such procedure.

4. Operation •

After bleeding the air, stop the engine and wait for at least 5 minutes before starting operations. In this way, the air bubbles are removed from the oil inside the hydraulic tank.

•

Check for any leakage of oil and wipe off any oil that has been spilled.

MX15 Operator’s Manual

Attachments and Options - 200

Machine Ready for Attachment

Attachment Operation

WARNING Do not carry out operations with your foot on the pedal. If the pedal is depressed by mistake, the attachment may suddenly move and cause a serious accident.

The operation of the attachment is as follows.

When Using Breaker Depress the bottom of the pedal to operate the breaker.

Precautions When Using •

Check that the stopper valve is in the FREE position.

•

Check that the selector valve is in the position for 1WAY (using the breaker).

•

When using the breaker, pull the fuel control lever back fully, then return it slightly and keep it in this position for operations (the position for 80% of engine output).

•

If the breaker is operated with the engine at full throttle, it will lead to failure.

•

When using the breaker, the hydraulic oil deteriorates more, so replace the element at a shorter interval. For details, see “Maintenance Interval for Hydraulic Breaker” on page 155.

•

For details of other precautions when handling the breaker, read and use correctly the instruction manual provided by the breaker manufacturer.

MX15 Operator’s Manual Machine Ready for Attachment When Using General Attachment Such As Crusher When the pedal is depressed, the attachment is actuated.

Precautions When Using •

Check that the stopper valve is in the FREE position.

•

Check that the selector valve is in the position for 2WAY (for crusher and other general attachment).

•

For details of other precautions when handling the breaker, read and use correctly the instruction manual provided by the breaker manufacturer.

Attachments and Options - 201

Attachments and Options - 202

MX15 Operator’s Manual Attachment Guide

Attachment Guide WARNING •

Please read the instruction manual for the attachment and the sections of this manual related to attachments and options.

•

When installing any attachment or option, there may be problems with safety, so please contact your Ditch Witch dealer before installing.

•

Installing attachments or options without consulting your Ditch Witch dealer may not only cause problems with safety, but may also have an adverse effect on the operation of the machine and the life of the equipment.

•

Any injuries, accidents, or damage resulting from the use of unauthorized attachments or options will not be the responsibility of The Charles Machine Works, Inc.

Attachment Combinations

WARNING •

Depending on the type or combination of attachments, there is danger that the attachments may hit the cab or machine body.

•

When using unfamiliar attachments for the first time, check before starting if there is any danger of interference, and operate with caution.

This is the combination table for buckets that can be installed to the standard arm.

•

If a long arm is installed, do not pull the bucket fully in toward the machine. It will hit the machine body.

•

When lowering the boom while digging diagonally, be careful not to let the bucket hit the undercarriage.

MX15 Operator’s Manual

Attachments and Options - 203

Attachment Guide Categories •

For general digging: digging or loading sand, gravel, clay etc.

•

For light duty digging: digging or loading dry, uncaked soil and sand, mud etc.

•

For loading work: loading dry, loose soil and sand

Judgement •

{: Can be used

•

: Can be used only for light duty work

•

[: Cannot be used

Name

Capacity

Outside width

Use

Standard arm

Long arm

Standard bucket

0.044 m3/0.06 yd3

500 mm/19.7”

General digging

{

[

Narrow bucket

0.040 m3/0.05 yd3

250 mm/9.9”

Narrow digging

{

{

Narrow bucket

0.028 m3/0.04 yd3

350 mm/13.8”

Narrow digging

{

{

Attachments and Options - 204

MX15 Operator’s Manual Attachment Guide

Hydraulic Breaker Select the hydraulic breaker matched to the machine body.

•

Install only attachments specified by The Charles Machine Works, Inc. For a list of approved attachments, consult your Ditch Witch dealer.

Main Applications •

Crushed rock

•

Demolition work

•

Road construction

This attachment can be used for a wide range of applications including demolition of buildings, breaking up road surfaces or slag, tunnel work, rock crushing and breaking operations in quarries.

Keep the chisel pushed perpendicularly against the impact surface when carrying out breaking operations.

When applying impact, push the chisel against the impact surface and operate so that the chassis rises approx. 5 cm (2”) off the ground. Do not let the machine come further off the ground than this amount.

MX15 Operator’s Manual Attachment Guide When applying continuous impact to the same impact surface, if the chisel does not penetrate or break the surface within one minute, change the point of impact and carry out breaking operations closer to the edge.

The direction of penetration of the chisel and the direction of the breaker body will gradually move out of line with each other, so always adjust the bucket cylinder to keep them aligned.

Always keep the chisel pressed against the impact surface properly to prevent using the impact force when there is no resistance.

Attachments and Options - 205

Attachments and Options - 206

MX15 Operator’s Manual Attachment Guide

Prohibited Works To ensure that the machine has a long life and to ensure that operations are carried out in safety, do not operate the machine in any of the following ways.

•

Do not operate all cylinders to the end of their strokes. Always leave approx. 5 cm (2”) to spare.

Using the mount to gather in pieces of rock

Operations using the swing force

Moving the chisel while carrying out impacting operations

Applying impact horizontally or in upward direction

MX15 Operator’s Manual Attachment Guide Twisting the chisel when it has penetrated the rock

Pecking operations

Extending the bucket cylinder fully and thrusting to raise the machine off the ground

Attachments and Options - 207

Attachments and Options - 208

MX15 Operator’s Manual Attachment Guide

Greasing Position for Hydraulic Breaker Supply grease in the correct position.

NOTICE If grease is supplied in an incorrect position, the breaker is filled with more grease than necessary.

As a result, soil and sand will enter the hydraulic circuit and can damage the hydraulic devices while the breaker is used. Accordingly, be sure to supply grease in the correct position.

MX15 Operator’s Manual

Support - 209

Procedure

Support Procedure Notify your dealer immediately of any malfunction or failure of Ditch Witch equipment.

Always give model, serial number, and approximate date of your equipment purchase. This information should be recorded and placed on file by the owner at the time of purchase.

Return damaged parts to dealer for inspection and warranty consideration if in warranty time frame.

Order genuine Ditch Witch replacement or repair parts from your authorized Ditch Witch dealer. Use of another manufacturer’s parts may void warranty consideration.

Resources Publications Contact your Ditch Witch dealer for publications and videos covering safety, operation, service, and repair of your equipment.

Ditch Witch Training For information about on-site, individualized training, contact your Ditch Witch dealer.

MX15 Operator’s Manual

Warranty - 210

Warranty Ditch Witch Equipment and Parts Limited Warranty Policy Subject to the limitations and exclusions herein, free replacement parts will be provided at any authorized Ditch Witch dealership for any Ditch Witch equipment or parts manufactured by The Charles Machine Works, Inc. (CMW) that fail due to a defect in material or workmanship within one (1) year of first commercial use (Exception: 2 years for all SK500 attachments). Free labor will be provided at any authorized Ditch Witch dealership for installation of parts under this warranty during the first year following initial commercial use of the serial-numbered Ditch Witch equipment on which it is installed.

Exclusions from Product Warranty •

Wear-related failure of parts subject to ground contact including, but not limited to, digging teeth, digging chains, sprockets, backhoe buckets, plow blades, drill pipe, drill bits, backreamers, and swivels.

•

All incidental or consequential damages.

•

All defects, damages, or injuries caused by misuse, abuse, improper installation, alteration, neglect, or uses other than those for which products were intended.

•

All defects, damages, or injuries caused by improper training, operation, or servicing of products in a manner inconsistent with manufacturer’s recommendations.

•

All engines and engine accessories (these are covered by original manufacturer’s warranty).

•

Tires, belts, and other parts which may be subject to another manufacturer’s warranty (such warranty will be available to purchaser).

•

All implied warranties not expressly stated herein, including any warranty of fitness for a particular purpose and merchantability.

IF THE PRODUCTS ARE PURCHASED FOR COMMERCIAL PURPOSES AS DEFINED BY THE UNIFORM COMMERCIAL CODE, THEN THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE FACE HEREOF AND THERE ARE NO IMPLIED WARRANTIES OF ANY KIND WHICH EXTEND TO A COMMERCIAL BUYER. ALL OTHER PROVISIONS OF THIS LIMITED WARRANTY APPLY INCLUDING THE DUTIES IMPOSED. Ditch Witch products have been tested to deliver acceptable performance in most conditions. This does not imply they will deliver acceptable performance in all conditions. Therefore, to assure suitability, products should be operated under anticipated working conditions prior to purchase.

Defects will be determined by an inspection within thirty (30) days of the date of failure of the product or part by CMW or its authorized dealer. CMW will provide the location of its inspection facilities or its nearest authorized dealer upon inquiry. CMW reserves the right to supply remanufactured replacements parts under this warranty as it deems appropriate.

Extended warranties are available upon request from your local Ditch Witch dealer or CMW. Some states do not allow exclusion or limitation of incidental or consequential damages, so above limitation of exclusion may not apply. Further, some states do not allow exclusion of or limitation of how long an implied warranty lasts, so the above limitation may not apply. This limited warranty gives product owner specific legal rights and the product owner may also have other rights which vary from state to state.

For information regarding this limited warranty, contact CMW’s Product Support department, P.O. Box 66, Perry, OK 73077-0066, or contact your local Ditch Witch dealer.

First version: 1/91; Latest version: 1/03