CLAAS ROLLANT 250 ROLLANT 250 ROTO CUT REPAIR MANUAL - PDF DOWNLOAD

REPAIR MANUAL

CLAAS ROLLANT 250 ROLLANT 250 ROTO CUT

Re ad an df oll o w sa f et yi ns

t ru

cti

on

s!

Contents CONTENTS Contents ................................................................................ 0.1.1

1. General information General .................................................................................. 1.1.1 Introduction ...................................................................... 1.1.1 Introduction to the CLAAS REPAIR MANUAL ................. 1.1.2 Key to symbols ................................................................ 1.1.3 Safety rules ............................................................................ 1.2.1 Important information ....................................................... 1.2.1 Identification of warning and danger signs ...................... 1.2.2 Correct use of the round baler ......................................... 1.2.2 General safety and accident prevention regulations ....... 1.2.2 Leaving the round baler ................................................... 1.2.2 Service ............................................................................. 1.2.3 Basic rule ......................................................................... 1.2.3 General repair information ..................................................... 1.3.1 Reason of damage .......................................................... 1.3.1 Spare parts ...................................................................... 1.3.1 Transmission ................................................................... 1.3.1 Tensioning the steel roller chains .................................... 1.3.1 Taper ring fasteners ........................................................ 1.3.1 Self-locking bolts ............................................................. 1.3.1 Liquid locking compound ................................................. 1.3.1 Correct installation of lock collar bearings ....................... 1.3.2 Correct installation of adapter sleeve bearings ................ 1.3.2 Ferrule fittings on hydraulic lines ..................................... 1.3.2 Progressive ring fittings on hydraulic lines ....................... 1.3.3 Taper fittings on hydraulic lines ....................................... 1.3.3 Welding ............................................................................ 1.3.3 Some advice for speedy and correct repair work: ........... 1.3.4 Tightening torques ................................................................. 1.4.1 Bolts ................................................................................. 1.4.1 Hydraulic screw fittings .................................................... 1.4.2 Specifications ......................................................................... 1.5.1 Lubricants chart ............................................................... 1.5.1

2. Drives Universal Drive Shaft ............................................................. 2.1.1 Disassembling the universal drive shaft half (tractor side) .................................................................... 2.1.1 Assembling the universal drive shaft half on the tractor side ....................................................................... 2.1.4 Disassembling the universal drive shaft half (machine side) ................................................................. 2.1.7 Assembling the universal drive shaft half (machine side) ................................................................. 2.1.8 Disassembling the cam-type cut-out clutch ................... 2.1.11 Assembling the cam-type cut-out clutch ........................ 2.1.12 Angle drive, intermediate drive .............................................. 2.2.1 Removing the angle drive ................................................ 2.2.1 Disassembling the angle drive ......................................... 2.2.2 Assembling the angle drive ............................................. 2.2.7 Installing the angle drive ................................................ 2.2.14 Drive Diagram ........................................................................ 2.3.1 Drives, left-hand side ....................................................... 2.3.1 Drives, right-hand side ..................................................... 2.3.2

298 332.0 - RHB ROLLANT 250 / 250 RC

Drive chains, left-hand side ................................................... 2.4.1 Removing the roller drive (top) ........................................ 2.4.1

Installing and tensioning the roller drive (top) ................. 2.4.3 Removing the roller drive (front) ...................................... 2.4.6 Installing the roller drive (front) ........................................ 2.4.7 Removing the cutting rotor/feed rotor drive ..................... 2.4.9 Installing and adjusting the cutting rotor/ feed rotor drive .............................................................. 2.4.10 Removing the drive of rollers 1, 2 and 16 ..................... 2.4.11 Installing and adjusting the drive of rollers 1, 2 and 16 . 2.4.12 Removing the pick-up drive (left) .................................. 2.4.13 Installing the pick-up drive (left) .................................... 2.4.14 Removing the intermediate drive of pick-up drive on rotor machines ......................................................... 2.4.17 Installing the intermediate drive of pick-up drive on rotor machines ......................................................... 2.4.18 Drive chains/drive belts on right-hand side ........................... 2.5.1 Removing the feed auger drive (right) ............................. 2.5.1 Installing the feed auger drive (right) ............................... 2.5.1 Removing the tailgate roller drive .................................... 2.5.2 Installing the tailgate roller drive ...................................... 2.5.3 Removing and disassembling the tying drive .................. 2.5.6 Assembling and mounting the tying drive ....................... 2.5.8 Removing and installing the net wrapping/ twine wrapping drives .................................................... 2.5.11

3. Pick-up / Rollers Pick-up lift .............................................................................. 3.1.1 Removing the hydraulic pick-up lift ................................. 3.1.1 Installing the hydraulic pick-up lift ................................... 3.1.2 Pick-up .................................................................................. 3.2.1 Removing the gauge wheel ............................................. 3.2.1 Disassembling the gauge wheel ..................................... 3.2.1 Gauge wheel, disassembled ........................................... 3.2.3 Assembling the gauge wheel .......................................... 3.2.4 Removing the short crop baffle ....................................... 3.2.5 Installing the short crop baffle ......................................... 3.2.6 Replacing the spring tine ................................................. 3.2.6 Removing the pick-up and auger .................................... 3.2.6 Pick-up and auger, disassembled ................................... 3.2.7 Installing the pick-up and auger ...................................... 3.2.8 Replacing the left-hand drive shaft lock collar bearing .... 3.2.9 Replacing the right-hand drive shaft lock collar bearing 3.2.10 Removing the pick-up ................................................... 3.2.11 Mounting the pick-up ..................................................... 3.2.12 Removing the cam track ............................................... 3.2.13 Removing the guide rollers ........................................... 3.2.15 Removing the tine carrier .............................................. 3.2.16 Removing the drive shaft .............................................. 3.2.16 Pick-up, disassembled .................................................. 3.2.17 Mounting the tine carrier ............................................... 3.2.19 Mounting the cam track ................................................. 3.2.19 Cutting/feed unit .................................................................... 3.3.1 Removing the cutting rotor/feed rotor .............................. 3.3.1 Disassembling the cutting rotor/feed rotor ...................... 3.3.2

0.1.1

Contents Cutting rotor/feed rotor, disassembled ............................. 3.3.4 Assembling the cutting rotor/feed rotor ............................ 3.3.5 Installing the cutting rotor/feed rotor ................................ 3.3.5 Removing the scraper of cutting rotor/feed rotor ............. 3.3.8 Installing the scraper of cutting rotor/feed rotor ............... 3.3.8 Removing the knife shaft ................................................. 3.3.9 Knife shaft, disassembled .............................................. 3.3.11 Installing the knife shaft ................................................. 3.3.12 Rollers .................................................................................... 3.4.1 Removing roller 3 ............................................................. 3.4.1 Roller 3, disassembled .................................................... 3.4.5 Installing roller 3 ............................................................... 3.4.6 Removing roller 11 ........................................................... 3.4.9 Remove tailgate. .............................................................. 3.4.9 Roller 11, disassembled ................................................ 3.4.11 Installing roller 11 ........................................................... 3.4.12 Swinging segment .................................................................. 3.5.1 Removing the swinging segment ..................................... 3.5.1 Disassembling the swinging segment .............................. 3.5.2 Assembling the swinging segment .................................. 3.5.4 Installing the swinging segment ....................................... 3.5.9 Removing the hydraulic backwinder ...................................... 3.6.1 Hydraulic backwinder, disassembled ............................... 3.6.2 Mounting the hydraulic backwinder ................................. 3.6.3 Replacing the mechanical backwinder ............................ 3.6.7

Disassembling the 4/3-way valve with circulation shut-off valve ................................................................... 6.1.6 Assembling the 4/3-way valve with circulation shut-off valve ................................................................... 6.1.7 Mounting the 4/3-way valve with circulation shut-off valve ................................................................... 6.1.8 Removing the NG2 solenoid valve .................................. 6.1.9 Disassembling the NG2 solenoid valve ........................... 6.1.9 NG 2 solenoid valve, disassembled .............................. 6.1.11 Assembling the NG2 solenoid valve .............................. 6.1.12 Mounting the NG2 solenoid valve ................................. 6.1.14 Hydraulic cylinders ................................................................ 6.2.1 Removing and installing the hydraulic cylinders .............. 6.2.1 Disassembling the hydraulic cylinders ............................ 6.2.2 Assembling the hydraulic cylinders ................................. 6.2.4 Disassembling the hydraulic cylinder (knife lift) ............... 6.2.6 Assembling the hydraulic cylinder (knife lift) ................... 6.2.6

7. Index

4. Twine and net wrapping Twine Wrapping ..................................................................... 4.1.1 Removing the twine wrapping unit ................................... 4.1.1 Removing the cutting unit ................................................ 4.1.2 Removing the deflector .................................................... 4.1.3 Disassembling the twine wrapping unit ............................ 4.1.3 Disassembling the cutting unit ......................................... 4.1.6 Assembling the cutting unit ............................................ 4.1.13 Assembling the twine wrapping unit .............................. 4.1.14 Installing the deflector .................................................... 4.1.19 Installing the cutting unit ................................................ 4.1.21 Mounting the twine wrapping unit .................................. 4.1.23 Net wrapping .......................................................................... 4.2.1 Removing the net wrapping unit ...................................... 4.2.1 Disassembling the net wrapping unit ............................... 4.2.3 Assembling the net wrapping unit .................................. 4.2.13 Mounting the net wrapping unit ...................................... 4.2.20

5. Machine housing Tailgate .................................................................................. 5.1.1 Removing the tailgate ...................................................... 5.1.1 Mounting the tailgate ....................................................... 5.1.3

6. Hydraulic system – Electric system Valve combination .................................................................. 6.1.1 Checking the tightness of tailgate valve combination and hydraulic cylinder ............................................................. 6.1.1 Removing the valve combination ..................................... 6.1.2 Disassembling the valve combination .............................. 6.1.3 Valve combination, disassembled ................................... 6.1.4 Assembling the valve combination .................................. 6.1.5 Removing the 4/3-way valve with circulation shut-off valve ................................................................... 6.1.6

0.1.2

RHB ROLLANT 250 / 250 RC - 298 332.0

1 General information

General GENERAL Introduction This CLAAS REPAIR MANUAL is to assist in preserving the permanent working order and therefore the high value of your CLAAS round baler by careful maintenance and service.

Experience gathered by both our service engineers and factory staff has been compiled in this REPAIR MANUAL. The figures explain the procedure of repairs and the text describes the different adjustments to be made, the use of CLAAS special tools etc.

The illustrations included in support to the explanations show the sequence of major repairs so that minor repairs can easily be followed.

The CLAAS REPAIR MANUAL is filed in a folder which allows to insert supplementary pages as issued following technical developments and to always have an updated manual at hand for reference.

To be sure, always compare settings and filling capacities with specifications stated in the current Operator’s Manual which applies to the machine.

CLAAS KGaA mbH Service Department

298 332.0 - RHB ROLLANT 250 / 250 RC

1.1.1

General Introduction to the CLAAS REPAIR MANUAL The CLAAS REPAIR MANUAL is divided into main groups and subgroups.

Pages and illustrations are numbered consecutively throughout each main group. The first figure at the bottom of each page refers to the main group whereas the second figure following the point indicates the subgroup; the figure behind the second point indicates the page number. In each subgroup, the figures and pages are numbered consecutively, starting at 1.

Where differences between the machine types must be observed, this is indicated in headings. Where a service procedure applies to all machines covered by this book, the machine names are not specifically given.

When supplements are to be added, the subgroups are supplemented or exchanged. All supplements are inserted into the respective main group / subgroup and the table of contents is updated.

The symbols communicate brief messages when recurring service procedures are described. Their meaning is explained at the beginning of this manual.

The section “GENERAL REPAIR INSTRUCTIONS” at the beginning of this manual contains useful practical hints. Read and follow these fundamental instructions.

They are the basis for reliable service and durability of parts after repairs have been carried out.

The description of a particular service procedure can easily be found by checking the table of contents of the appropriate main group / subgroup.

1.1.2

RHB ROLLANT 250 / 250 RC - 298 332.0

General Key to symbols This CLAAS REPAIR MANUAL uses some symbols as defined in the “DIN 30600 Symbol summary” by the German Standardisation Institute (DIN).

The meaning of these symbols will be easily recognised and remembered by the user. These symbols are to help to quickly recognise recurring service procedures and they also help to communicate information shown on the illustrations.

Dismantle, remove

Grease

Prevent damage to materials

Disassemble

Oil

Special tools

Assemble

Adjust/set

Drain, outlet

Install, mount on

Check visually

Fill, filler opening

Mark

Unlock, release, secure

Overflow

Balance

Lock by means of liquids, glue, seal

Bleed

Possibly reuseable

Underprop, support

Renew on each assembly

Observe direction of installation

298 332.0 - RHB ROLLANT 250 / 250 RC

1.1.3

Safety rules SAFETY RULES

Important information The instructions contained in this manual should be carefully read and observed by all persons who are concerned with the operation, maintenance and inspection of this machine in order to prevent accidents. In particular, read the section “Safety rules”.

The use of spare parts, accessories and ancillary equipment other than genuine CLAAS products or those which have been tested and approved by CLAAS, may change the specified design characteristics of this CLAAS machine or detract from its functional performance, with a possible adverse effect on the active and/or passive operational safety of the machine and its occupational safety standards (accident prevention).

CLAAS is in no way liable for any damage or personal injury caused through the use of other than original or approved CLAAS parts, accessories and ancillary equipment.

Technical data, dimensions and weights are given as an indication only. CLAAS reserve the right to make changes subsequently as technical developments continue. Responsibility for errors and omissions not accepted.

IMPORTANT: Front, rear, right and left refer to the direction of forward travel.

298 332.0 - RHB ROLLANT 250 / 250 RC

1.2.1

Safety rules Identification of warning and danger signs

Correct use of the round baler

All parts of this manual having to do with your safety or the safe operation of the machine are marked with the following signs. Please pass all safety instructions on to other users, too.

Fitting and retrofitting of ancillary equipment which is not originally manufactured by CLAAS, and, in addition, also modifications and changes may only be carried out with the consent of CLAAS, as any such actions may have considerable adverse effects on the safety and operational function of the machine.

Danger!

Sign to indicate instructions which must be observed. Failure to do so would cause danger to life and limb to the operator and the people around him.

Any arbitrary modifications carried out on the round baler will relieve the manufacturer of all liability for any resulting damage or injury.

☞ Preventive measures

General safety and accident prevention regulations

Caution!

1. In addition to the instructions contained in this manual, also observe the general safety and accident prevention regulations.

Sign to indicate instructions which must be observed. Failure to do so could result in damage to the machine.

2. Always comply with local traffic regulations when driving on public roads!

☞ Measures to prevent damage to the

3. Clothing worn by the fitter must be close-fitting.

Avoid wearing loose jackets and shirts.

machine

4. Prevent fires by keeping the machine clean!

Note!

Sign to indicate instructions for a more efficient and economic use of the machine.

Important!

Sign to indicate instructions to be followed during disassembly / assembly.

Leaving the round baler 1. Repair, service and cleaning work and the elimination of malfunctions should only be performed with the drive and the tractor engine switched off – remove the ignition key!

2. Escaping fluid (fuel or hydraulic oil) under high pressure can penetrate the skin and cause serious injury. In such a case, consult a doctor immediately as otherwise serious infections may result!

Environment!

Sign to indicate instructions which must be observed in order to avoid damage to the environment.

Danger to the environment is caused by irregular handling and incorrect disposal of toxic material (e.g. used oil).

The warning and instruction signs placed on the round baler provide recommendations for safe operation. These instructions involve your safety – observe them at all times!

1.2.2

RHB ROLLANT 250 / 250 RC - 298 332.0

Safety rules Service 1. Repair, service and cleaning work and the elimination of malfunctions should only be performed with the drive and the tractor engine switched off – remove the ignition key!

2. Escaping fluid (fuel or hydraulic oil) under high pressure can penetrate the skin and cause serious injury. In such a case, consult a doctor immediately as otherwise serious infections may result!

3. Dispose of oil, fuel and filters in a way that is harmless to the environment and in accordance with existing anti-pollution regulations.

4. Do not attempt to mount a tyre unless you have the proper equipment and experience to perform the job safely.

5. Retighten the wheel nuts regularly.

6. Only have qualified workshops carry our repair work on the hydraulic system.

Basic rule Always check the operating and road safety of the round baler before using it!

298 332.0 - RHB ROLLANT 250 / 250 RC

1.2.3

General repair information GENERAL REPAIR INFORMATION

Removal:

Reason of damage

After loosening the axial clamping, loosen the taper ring fasteners with a sharp blow, using a block-ended tube.

Identify reason of damage, limit the case of damage and safeguard the machine.

Spare parts Use genuine CLAAS spare parts and corresponding CLAAS special tools.

Indicate the machine number of the round baler and also the respective serial numbers when ordering spare parts and in case of technical questions. This is necessary as otherwise, incorrect spare part deliveries may result.

Transmission When removing the transmission, first drain the oil and then remove the transmission. Separate parts which are firmly connected with each other by means of a soft metal-tip or plastic-tip hammer.

Tensioning the steel roller chains Find the centre point in the slack span between sprockets. With the tight span slightly under load, push in the centre point of the slack span with the thumb.

The chain tension is correct when its slack span deflects about 2% of the centre distance between shafts. Check chain tension more frequently when using new chains.

Example: For a distance between centres of shafts of 500 mm, the slack span of the chain should deflect about 10 mm.

Taper ring fasteners Taper ring fasteners provide a safe mechanical connection, even when transmitting high forces from the driving element on the shaft and vice versa, if they are properly prestressed.

Caution!

The inside diameter of the block-ended tube must be large enough to extend over the tapered ring.

Self-locking bolts (with microencapsulated adhesive) Replace self-locking bolts, e.g. Verbus-Plus / Imbus-Plus and similar types every time such bolts are removed. In exceptional cases, they may be reused up to three times. Always observe the specified tightening torque.

Always tighten self-locking bolts with microencapsulated adhesive rapidly to the specified tightening torque. When removing these bolts, quickly unscrew them completely. These self-locking bolts must not come into contact with sealing compound (e.g.

“Epple 33” or similar products).

In individual cases, bolts with liquid locking compound can be used instead of self-locking bolts only where these bolts can be heated up to approx. 200 °C for removing them. Ensure that the specified quality grade of bolts (8.8/10.9 or similar grades) is observed here as well.

Self-locking bolts with microencapsulated adhesive may be used only where operating temperatures will not exceed +90 °C max. These bolts can be subjected to full stress after 24 hours at +20 °C. To speed up the curing time, heating may be applied (e.g. to 15 minutes at +70 °C).

Installation:

Liquid locking compound

When installing taper ring fasteners, it is important that the shaft, hub, parallel key and the taper rings have been thoroughly cleaned, that semi-fluid lubricant of NLGI class 00 (e.g. Shell Retinax G or similar brands) is applied and that the components are tightened to the specified torque in the correct order of assembly.

(e.g. Delo-ML 187 / Loctite 242 or similar types)

Caution!

Use liquid locking compound only where specified by the manufacturer.

Correct application: Metal surfaces where liquid locking compound is to be applied must be absolutely free from grease. Use the “Aktivator” included in the workshop package for cleaning.

No solid grease must be used when assembling the parts.

298 332.0 - RHB ROLLANT 250 / 250 RC

1.3.1

General repair information Before applying the liquid locking compound, the metal surfaces where Aktivator has been applied must have dried. Especially in blind holes, no Aktivator (cleaning agent) residues are allowed.

When installing bolts, apply the liquid locking compound only to the internal thread (nut) if possible in small quantities (drops). In blind holes only wet approx. 1d (d = nominal diameter of bolt) at the thread bottom. The same applies to any extra-long female threads. When applying the liquid locking compound to the bolt or at the top end of a female thread, the liquid locking compound will spread over the entire thread length when screwing the bolt in. As a result, too much break-away torque is required to remove the bolt – Danger of breaking!

Threaded assemblies secured with liquid locking compound can be easily unscrewed by heating them up to approx. 200 °C.

Correct installation of lock collar bearings Lock collar bearings are tightened on the shaft by rotating the eccentric ring over the inside bearing ring.

Prior to installation, apply semi-fluid lubricant of NLGI class 00 (e.g. Shell Retinax G or similar brands) to the inside ring and the shaft to make bearing removal easier during future repairs.

Always fasten the eccentric ring moderately in the direction of rotation of the shaft and lock by means of a set screw. To remove the bearing, loosen the eccentric ring in opposite direction of rotation of the shaft.

Correct installation of adapter sleeve bearings Adapter sleeve bearings do not require a specially machined bearing seat. They may be mounted on any drawn or scalped shaft. This is an advantage because it allows the shaft to be axially moved as required to obtain correct alignment.

Always install adapter sleeve bearings according to the conical inside ring. Clean the taper lock adapter sleeve and the shaft and check that the sleeve nut runs easily so the taper lock adapter sleeve will not turn on the shaft when tightening.

Tightening the bearing: First tighten the sleeve nut to the point where the taper lock adapter sleeve has no more play and is under slight preload. Now tighten the nut by approx. 90° and continue turning until the next nearest slot fits the tab.

Secure sleeve nut with the tab.

Loosening the bearing: Bend up the tab which secures the sleeve nut and first back off the nut a few turns only (the thread must still fully grip). Loosen the taper lock adapter sleeve with a sharp blow, using a block-ended tube.

Ferrule fittings on hydraulic lines When pre-assembling the unit and for pre-assembled factory-delivered ferrule fittings, the following applies: installation is in the associated, well-oiled threaded joint with half a turn of the union nut beyond the point where resistance is felt.

Pre-assembly: 1. Cut off the tube at right angles. Do not use a pipe cutter because this will slant the tube wall, causing heavy inside and outside burrs. Slightly deburr the tube end on the inside and outside (do not chamfer!) and clean it. In case of tube bends, the straight tube end up to where the bending radius starts must be at least twice the height of the union nut.

2. Push the union nut and the ferrule on the tube.

3. Push the tube against the stop in the union and tighten union nut until the ferrule grips the tube (the tube must not rotate with the nut). This point can be felt because increase power is needed from here.

4. Tighten the union nut half a turn beyond the point where resistance is felt.

5. Check the cut made by the ferrule edge: A visible shoulder must fill the space before the ferrule front end. The ferrule may rotate, but axial displacement must not be possible.

Installation: Insert the pre-assembled tube into the well-oiled threaded joint, tighten the union nut up to the point where resistance is felt and then half a turn beyond this point.

1.3.2

RHB ROLLANT 250 / 250 RC - 298 332.0

General repair information Re-installation:

Re-installation:

Every time the ferrule fitting has been loosened, retighten the union nut without using increased force.

Every time the progressive ring fitting has been loosened, retighten the union nut until resistance is felt and then continue for half a turn beyond that point.

Ferrule fitting leaks: If a ferrule fitting leaks, first loosen the union nut until some oil escapes and then tighten it as specified.

Important: Back up the threaded joint with a wrench!

Progressive ring fitting leaks:

Progressive ring fittings on hydraulic lines When pre-assembling the unit and for pre-assembled factory-delivered progressive ring fittings, the following applies: installation is in the associated, well-oiled threaded joint with half a turn of the union nut beyond the point where resistance is clearly felt.

If a progressive ring fitting leaks, first loosen the union nut until some oil escapes and then tighten it as specified.

Caution!

Failure to observe the tightening torques reduces the nominal power and the service life of the fitting, resulting in leaks and in the tube slipping out.

Pre-assembly: 1. Cut off the tube at right angles. Do not use a pipe cutter because this will slant the tube wall, causing heavy inside and outside burrs. Slightly deburr the tube end on the inside and outside (do not chamfer!) and clean it. In case of tube bends, the straight tube end up to where the bending radius starts must be at least twice the height of the union nut.

2. Push the union nut and the progressive ring on the tube.

3. Push the tube against the stop in the union and tighten union nut until the progressive ring grips the tube (the tube must not rotate with the nut).

This point can be felt because increase power is needed from here.

Taper fittings on hydraulic lines Montage: Apply oil to the O-ring on the taper. Tighten the union nut a third of a turn beyond the point where resistance is felt.

Important: Back up the threaded joint with a wrench!

Caution!

Failure to observe the tightening torques reduces the nominal power and the service life of the fitting, resulting in leaks and in the tube slipping out.

4. Tighten the union nut half a turn beyond the point where resistance is felt.

5. Check the cut made by the progressive ring edge: A visible shoulder must fill the space before the progressive ring front end. The progressive ring may rotate, but axial displacement must not be possible.

Installation: Insert the pre-assembled tube into the well-oiled threaded joint, tighten the union nut up to the point where resistance is felt and then half a turn beyond this point.

Important: Back up the threaded joint with a wrench!

Welding Caution!

When carrying out electric welding work on the machine, proceed as follows: 1. Turn off the battery isolating switch!

2. Disconnect the connector to the display monitor.

3. Pull out the electrical plug-in modules in the central terminal compartment.

4. Always connect the earth clamp of the welder in the near vicinity of the area where the welding is being carried out.

298 332.0 - RHB ROLLANT 250 / 250 RC

1.3.3

General repair information Some advice for speedy and correct repair work: – Mark machine parts prior to disassembly to ensure their correct left-to-right positions and balance when reassembled.

– Fit expansion pins with the slot facing the side under load. When fitted with a quarter turn from this position, they will get loose, fall out or shear off.

– Replace cotter pins, locking wires, locking plates, tab washers and lock washers when carrying out repairs.

– Fit lubricated ball and slide bearings with high-quality grease.

– Align chain wheels and V-belt pulleys towards each other.

– Care for strict cleanliness when working on hydraulic systems.

– Never mix different oil types.

– Run the machine or operate machine assemblies at low speed after any repair.

1.3.4

RHB ROLLANT 250 / 250 RC - 298 332.0

Tightening torques TIGHTENING TORQUES Bolts Tightening torques (in Nm) of hexagon bolts, cheese-head screws and hexagon nuts Bolts and nuts Strength class

blackened, phosphatised or galvanized 8.8

Dimensions

Hexagon bolts DIN 931 DIN 933

Cheese-head screws DIN 912

Hexagon nuts DIN 934

Hexagon nuts DIN 934

12.9

Metric thread

M4

2.7

3.8

4.6

M5

5.5

8.0

9.5

M6

10.0

14.0

16.0

M8

23.0

33.0

40.0

M 10

45.0

63.0

75.0

M 12

78.0

110.0

130.0

M 14

122.0

175.0

210.0

M 16

195.0

270.0

325.0

M 18

260.0

370.0

440.0

M 20

370.0

525.0

630.0

M 22

510.0

720.0

870.0

M 24

640.0

900.0

1080.0

M 27

980.0

1400.0

1650.0

M 30

1260.0

1800.0

2160.0

Dimensions

Hexagon bolts DIN 960 DIN 961

10.9

Metric fine thread

M8x1

25

35

42

M 10 x 1.25

48

67

80

M 12 x 1.25

88

125

150

M 12 x 1.5

82

113

140

M 14 x 1.5

135

190

225

M 16 x 1.5

210

290

345

M 18 x 1.5

300

415

505

M 20 x 1.5

415

585

700

M 22 x 1.5

560

785

945

M 24 x 2

720

1000

1200

M 27 x 2

1050

1500

1800

M 30 x 2

1450

2050

2500

CAUTION! Cadmium-plated and copper-plated bolts and nuts must be tightened with tightening torques 25% below the specified values.

298 332.0 - RHB ROLLANT 250 / 250 RC

1.4.1

Hydraulic screw fittings Tightening torques for hydraulic screw fittings with O-ring according to ISO 6149

1.4.2

Dimensions

Tightening torque according to ISO 6149

M8x1

7+2 Nm

M 10 x 1

11+4 Nm

M 12 x 1,5

16+5 Nm

M 14 x 1,5

23+8 Nm

M 16 x 1,5

29+10 Nm

M 18 x 1,5

38+13 Nm

M 20 x 1,5

46+15 Nm

M 22 x 1,5

67+22 Nm

M 24 x 1,5

86+29 Nm

M 26 x 1,5

103+34 Nm

M 27 x 2

103+34 Nm

M 30 x 2

170+57 Nm

M 33 x 2

200+67 Nm

M 36 x 2

245+82 Nm

M 38 x 2

245+82 Nm

M 39 x 2

310+103 Nm

M 42 x 2

380+127 Nm

M 45 x 2

440+147 Nm

RHB ROLLANT 250 / 250 RC - 298 332.0

Specifications SPECIFICATIONS Lubricants chart Transmission

Oil type

Capacity

Transmission 540/min Transmission 1000/min

SAE 90 API-GL-5 SAE 90 API-GL-5

1.2 l 1.6 l

Spur gear in swinging segment

Semi-fluid lubricant 500 G

0.8 kg

298 332.0 - RHB ROLLANT 250 / 250 RC

1.5.1

2 Drives

Drives UNIVERSAL DRIVE SHAFT Disassembling the universal drive shaft half (tractor side) Unscrew all cheese-head sheet metal screws from the universal drive shaft guard (A).

A

Remove universal drive shaft guard.

(Fig. 1)

1 Remove slide ring (B) from the double yoke.

(Fig. 2) B

2 Unscrew the cheese-head sheet metal screw and rotate guard half (D) until the relief is aligned with the peg at the slide ring (C).

C

Remove guard half (D) from the lemon tube.

Remove slide ring (C).

(Fig. 3)

D 3 Clean the receivers in the grooved yoke and in the double yoke from dirt and rust.

E

Remove the circlips (E) from the receivers of the grooved yoke.

(Fig. 4)

4

298 332.0 - RHB ROLLANT 250 / 250 RC

2.1.1

Drives

H

Force one bushing in the double yoke (H) through on one side, using a tube, far enough for the grooved yoke to make contact.

F

Important!

The tube must be 1 mm smaller than the bushing diameter.

(Fig. 5) 5 Clamp the forced-out bushing (G) in a vise and drive it out by light blows against the double yoke.

(Fig. 6)

G 6 Push the centre cross assembly (K) downward to the stop, at the same time pushing the second bushing a little out of the double yoke.

K

(Fig. 7)

7 Remove centre cross assembly (K) from the double yoke (H) and the bushing.

H

(Fig. 8)

K 8

2.1.2

RHB ROLLANT 250 / 250 RC - 298 332.0

Drives Drive bushing (G) out of the double yoke (H).

(Fig. 9) H

G 9 Force a bushing (M) in the grooved yoke (N) through far enough, using a tube (R), until the centre cross assembly (K) makes contact.

R

N

Important!

The tube (R) must be 1 mm smaller than the bushing diameter.

K

(Fig. 10, 11) 10 Clamp the forced-out bushing (M) in a vise and drive it out by light blows against the grooved yoke (N).

N

(Fig. 11)

M 11 Push the centre cross assembly (K) downward to the grooved yoke (N) until the stop is reached.

N

(Fig. 12)

K 12

298 332.0 - RHB ROLLANT 250 / 250 RC

2.1.3

Drives Remove the centre cross assembly (K) from the bushing (M) and the grooved yoke (N).

N

(Fig. 13)

K

M

13 In the same way, remove the centre cross assembly (P) from the double yoke (H) and the slip-on yoke (O).

(Fig. 14)

O

H

P 14 Z

S

To replace the grooved yoke (Z), drive out the expansion pin (S) and pull grooved yoke off of lemon tube (T).

T

(Fig. 15)

15

Assembling the universal drive shaft half (tractor side)

L

Pull off the bushings (G) and (M) from the new centre cross assembly.

Important!

G

The inside of the bushings must be fully covered with needles (L). Grease needles if required.

The seals must be correctly inserted into the bushings.

M 16

(Fig. 16)

2.1.4

RHB ROLLANT 250 / 250 RC - 298 332.0

Drives Insert centre cross assembly (K) into the grooved yoke (N).

M

Place the bushing (M) in position on one side and push it in far enough to allow the circlip to be installed.

Important!

To prevent the needles from falling out when pushing the bushing in, lift centre cross assembly into the bushing.

K

N 17

(Fig. 17) Insert circlip (E).

(Fig. 18)

E

18 Push in bushing (M) from the other side. Insert circlip.

Important!

The entire circumference of the circlip must be placed inside the groove.

M

(Fig. 19)

19 Insert the cog of the centre cross assembly (K) into the receivers of the double yoke (M).

H K

Important!

The ball head (U) on the grooved yoke must be placed in the ball receiver at the double yoke.

(Fig. 20) U

298 332.0 - RHB ROLLANT 250 / 250 RC

20

2.1.5

Drives Place bushing (G) in position on one side and push in far enough until the washer and the circlip can be installed.

G

Important!

To prevent the needles from falling out when pushing the bushing in, lift centre cross assembly into the bushing.

21

In the same way, push in the bushing on the other side.

Install washer (I) and circlip (Q).

Q

I

Important!

The entire circumference of the circlip must be placed inside the groove.

(Fig. 21, 22)

22 Grease the groove in the grooved yoke and install slide ring (C).

(Fig. 23)

C

23 Push guard half (D) over the lemon tube, rotate by a quarter turn and screw cheese-head sheet metal screw C 4.2 x 9.5 into the slide ring (C).

(Fig. 23, 24)

D 24

2.1.6

RHB ROLLANT 250 / 250 RC - 298 332.0

Drives Grease the groove in the double yoke and install slide ring (B).

(Fig. 25) B

25 Slide on universal drive shaft guard (A) and fasten to the slide ring (B) with cheese-head sheet metal screws C 4.2 x 9.5.

A

(Fig. 26)

26

Disassembling the universal drive shaft half (machine side) Unscrew the cheese-head sheet metal screw from the slide ring.

E

Rotate the guard half (F) until the relief is aligned with the peg at the slide ring (E).

Remove guard half from the lemon tube.

Remove slide ring (E).

F

(Fig. 27) 27 Remove circlip (G) from the clutch housing.

Pull the hub with built-on lemon tube out of the clutch housing.

(Fig. 28)

G

28

298 332.0 - RHB ROLLANT 250 / 250 RC

2.1.7

Drives Remove lock wedges and leaf springs from the hub (N).

To replace the lemon tube (P), drive out expansion pin (S) and force lemon tube out of the hub.

S

Remove supporting ring (T) and circlip (V).

(Fig. 29)

N

T

P V

29 Remove dirt and rust from receivers in clutch housing (K) and shear pin clutch and/or cam-type cut-out clutch (R).

R K

Remove circlips and remove centre cross assembly in the same way as on the universal drive shaft half (tractor side).

(Fig. 30)

30

Assembling the universal drive shaft half (machine side) Pull off the bushings (A) from the new centre cross assembly.

Important!

The inside of the bushings must be fully covered with needles (L). Grease needles if required.

The seals (D) must be installed in the bushings, install if necessary.

D A 31

Install centre cross assembly in the clutch housing.

Push in bushings and install circlips.

(Fig. 31)

2.1.8

RHB ROLLANT 250 / 250 RC - 298 332.0

Drives Install the stub of the centre cross assembly (E) in the receivers of the shear pin clutch (B) and/or the cam-type cut-out clutch (R).

E

(Fig. 32, 33)

B 32

R 33 Place the bushing (A) in position on one side and push in far enough to allow installation of the washer and the circlip.

A

Important!

To prevent the needles from falling out when pushing the bushing in, lift centre cross assembly into the bushing.

(Fig. 34) 34 In the same way, push the bushing in on the other side.

Install washer and circlip (M).

Important!

M

The entire circumference of the circlip must be placed inside the groove.

(Fig. 35) 35

298 332.0 - RHB ROLLANT 250 / 250 RC

2.1.9

Drives Place circlip (V) and supporting ring (T) over the lemon tube (P).

Force on hub (N) and secure with expansion pin (S).

(Fig. 36, 37)

P V

N

T

36 Apply Klueber grease to the grooves in the hub.

Place the leaf spring (B) on the right-hand groove side (as viewed) and the lock wedge (O) in position.

Proceed in the same way on the other side..

(Fig. 37)

B O

S 37

N

Hold the lock wedges tight and push hub (N) into the clutch housing (K).

K

(Fig. 38)

38 To secure the hub, install circlip (G) in the clutch housing.

(Fig. 39) G

39

2.1.10

RHB ROLLANT 250 / 250 RC - 298 332.0

Drives Grease the groove in the retainer on the lemon tube and install slide ring (E).

(Fig. 40)

E

40 Push guard half (F) over the lemon tube, rotate a quarter turn and screw cheese-head sheet metal screw C 4.2 x 9.5 into the slide ring (E).

(Fig. 40, 41)

F 41

Disassembling the cam-type cut-out clutch Remove seal (D) from the clutch housing.

(Fig. 42)

D 42 Remove circlip (S) and supporting ring from the clutch housing.

Pull out hub (N).

(Fig. 43)

N

S 43

298 332.0 - RHB ROLLANT 250 / 250 RC

2.1.11

Drives Pull cam (A) out of the hub, then pull out spring assembly (B).

Check bushings in the hub and drive out carefully if necessary.

(Fig. 44)

A

B

A 44 To replace the clutch housing (G), remove guard half (F), force out bushings (T) of the centre cross assembly and remove clutch housing from the pegs.

G

(Fig. 27, 34, 45)

F T 45

Assembling the cam-type cut-out clutch If previously removed, force the bushings (C) into the hub so they are flush.

C

(Fig. 46)

46 Apply Klueber grease to spring assembly (B) and install it.

Important!

Install the correct spring assembly, matching the 540 rpm (1750 Nm) and/or 1000 rpm (1200 Nm) transmission.

B

(Fig. 47) 47

2.1.12

RHB ROLLANT 250 / 250 RC - 298 332.0

Drives Apply Klueber grease to the cam (A) and install it with the narrower peg facing forward so that the rectangular surfaces at the wider peg face each other as shown in the figure.

A

(Fig. 48)

A

48 Apply Klueber grease to the hub (N) and push it into the clutch housing (G).

(Fig. 49)

G N 49 Install supporting ring (E) and circlip (S).

(Fig. 43, 50)

E 50 Place the seal (D) in position and press it into the clutch housing.

D

(Fig. 51)

51

298 332.0 - RHB ROLLANT 250 / 250 RC

2.1.13

Drives ANGLE DRIVE, INTERMEDIATE DRIVE Removing the angle drive Remove universal drive shaft.

Remove pick-up crop guard.

Slightly raise the pick-up and support safely.

A

Remove panel (A) on the left-hand side.

C B

Remove the brace (B) from the shaft of the pick-up lift.

D

Loosen the bolt (E) and remove roller chains (C) and (D).

E 1

Important!

The roller chain (D) and the chain wheel are not provided on feed rake machines.

(Fig. 1) Unscrew bolt (E).

Pull chain wheel and/or chain wheels (F) off of the shaft.

F

(Fig. 1, 2) E

2 Suspend angle drive in lifting device. Pull bearing housing (L) off of the shaft.

Check bearing and force out of the bearing housing if required.

(Fig. 3) L

3

298 332.0 - RHB ROLLANT 250 / 250 RC

2.2.1

Drives Unscrew top and bottom bolts (S) from the angle drive (G).

Carefully lower the angle drive and remove it.

(Fig. 4)

G S

4 Disassembling the angle drive Important!

The 540 rpm angle drive is described here. The 1000 rpm angle drive must be disassembled in the same way. Any deviations are pointed out separately.

19

Drain transmission oil 5

Environment!

Collect transmission oil and dispose of properly!

Pull guard off of the shaft and remove guard from the transmission.

Remove the cover from the housing. Unscrew the bleed valve. Cut the slotted nut (19) open with a chisel and remove it.

(Fig. 5) Remove the cap (16) from the housing.

(Fig. 6)

16

6

2.2.2

RHB ROLLANT 250 / 250 RC - 298 332.0

Drives Force the shaft (25) out of the crown wheel (21).

Remove crown wheel, slotted nut and taper roller bearing from the housing.

(Fig. 7)

21

25 7 Drive the outer rings of the taper roller bearings (11) and (22) out of the housing and remove shims.

Important!

Note thickness of shims.

(Fig. 8) 22

11

8 Remove shaft seal (9) from the housing.

(Fig. 9)

9

9 Release slotted nut (10) (using an obliquely ground chisel).

Arrest the bevel gear shaft with a holder-up and remove slotted nut with slotted nut wrench.

Important!

10

10

To prevent chips from the released spot from entering the threads during removal (the slotted nut would jam and would have to be cut open), remove the slotted nut by rotating forward and backward.

(Fig. 10)

298 332.0 - RHB ROLLANT 250 / 250 RC

2.2.3

Drives Drive out the bevel gear shaft (15) to the inside and remove outside taper roller bearing (11).

15

Pull inside taper roller bearing (14) off of the bevel gear shaft.

(Fig. 11, 12)

11 Drive outer rings of the taper roller bearing (11) and (14) out of the housing and remove shims.

14

Important!

Note thickness of shims.

11

(Fig. 12)

12 Press shaft seal (24) out of the housing.

24

Clean all parts thoroughly and check their re-usability.

Clean sealing faces thoroughly.

(Fig. 13)

13

2.2.4

RHB ROLLANT 250 / 250 RC - 298 332.0

Drives

1 6 2

7

5

4

8 3 16

24

17 14

25

15

13 12 11 10 9

11 19 3

20

18

21 22 23

204388

14 Angle drive (540 rpm), disassembled: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25

298 332.0 - RHB ROLLANT 250 / 250 RC

Transmission Bleed valve Seal Screw plug Housing cover Detent edged ring VSKZ 8 Hexagon bolt M 8 x 20 8.8 A3C Identification plate Shaft seal AS 35 x 80 x 10 Slotted nut Taper roller bearing 302 09 Shim 65 x 85 x 1 Shim 65 x 85 x 0.1 Taper roller bearing 322 09 Bevel pinion Cap Transmission housing Screw plug M 16 x 1.5 Slotted nut Bushing Bevel gear Taper roller bearing 302 12 Shim 90 x 110 x 1 Shaft seal AS 60 x 85 x 8 Shaft

2.2.5

Drives

540/min 15 9 10 11 12 13 25

24

14

21

17 19

16

11 +

23

204389

22

7

5

15

1000/min 4 12 13 14 6 19

18

15

4

17 3

11

2

204452

6

5

7

8

16

2.2.6

RHB ROLLANT 250 / 250 RC - 298 332.0

Drives Assembling the angle drive Important!

Due to the helical gearing of the 1000 rpm angle drive, only a crown wheel and a bevel gear shaft of the same pair number (e.g. 38) may be installed.

(Fig. 17) 17

14

Danger!

15

Danger of burns!

☞ Wear protective gloves.

Heat up taper roller bearing (14) to approx. 100 °C and push it on the bevel gear shaft (15) up to the stop.

(Fig. 18) 18 Figure 19 shows the taper roller bearing (15) on the bevel gear shaft (4) of the 1000 rpm angle drive.

15

(Fig. 19) 4

19

298 332.0 - RHB ROLLANT 250 / 250 RC

2.2.7

Drives Insert the shims (12) removed when disassembling into the housing.

12 Important!

The thickness of shims may be 1.0 mm max. (target value).

In case of the 1000 rpm angle drive, the target value is 1.25 mm.

20

If “+0.15” is written behind the pair number on the crown wheel, 0.15 mm must be subtracted from the target value and in case of “-0.15”, 0.15 mm must be added.

(Fig. 20, 21)

21 Drive in the outer ring (14) of the taper roller bearing over the shims up to the stop.

11

Drive in the outer ring (11) of the taper roller bearing up to the stop from the other side.

(Fig. 22, 23)

22 Install bevel gear shaft (15) in the housing.

14

(Fig. 23)

15

23

2.2.8

RHB ROLLANT 250 / 250 RC - 298 332.0

Drives Turn housing upside down and support bevel gear shaft from the bottom.

11

Place taper roller bearing (11) in position and drive in up to the stop.

(Fig. 24)

24 Install new slotted nut with liquid locking compound (DELO-ML5249) and tighten it with slotted nut wrench (N) and holder-up (G).

G N

Important!

Use slotted nut wrench for 1000 rpm angle drive.

Secure slotted nut only after adjusting the backlash and the contact pattern.

25

Check the drag torque and tighten the slotted nut further or loosen it if necessary. for 540 rpm = 500 ... 600 Nmm for 1000 rpm = 1300 ...1400 Nmm (Fig. 25, 26)

26 Grease dust lips of the shaft seal (24) and push shaft seal over the shaft (25) up to the stop, with the dust lips pointing upwards.

25

P

Important!

To protect the dust lips, protect shaft with a plastic cover (P) or a similar protection.

24

(Fig. 27) 27

298 332.0 - RHB ROLLANT 250 / 250 RC

2.2.9

Drives Install the shims (23) removed during disassembly in the housing.

Important!

The shim thickness may be 1.3 mm max. (target value).

In case of the 1000 rpm angle drive, the target value is 1.25 mm.

23 28

(Fig. 28) Drive in the outer ring (22) of the taper roller bearing over the shims up to the stop.

(Fig. 29)

22

29 Drive in the outer ring (11) of the taper roller bearing up to the stop on the opposite side.

Apply pattern identification paste to the tooth flanks of the bevel gear shaft.

(Fig. 30) 11

30

Danger!

Danger of burns!

☞ Wear protective gloves!

22

Heat up taper roller bearing (22) to approx. 100 °C and insert into the outer ring.

(Fig. 31) 31

2.2.10

RHB ROLLANT 250 / 250 RC - 298 332.0

Drives

Danger!

Danger of burns!

11

☞ Wear protective gloves

19 21

Heat up crown wheel (21) and taper roller bearing (11) to approx. 100 °C. Place crown wheel on the taper roller bearing (22).

32

Place slotted nut (19) and taper roller bearing (11) on the crown wheel.

(Fig. 31, 32) Slide housing (17) over the shaft and slide on the heated components at the same time.

17

(Fig. 33)

33

Important!

If required, drive in the crown wheel with a brass punch up to the stop.

(Fig. 34)

34 On the 540 rpm angle drive, tighten slotted nut with slotted nut wrench 68/75.

Check drag torque 1200...1350 Nmm and if necessary tighten the slotted nut further or loosen it.

(Fig. 35)

35

298 332.0 - RHB ROLLANT 250 / 250 RC

2.2.11

Drives On the 1000 rpm angle drive, tighten the slotted nut in the same way and check drag torque of 900...1400 Nmm; if necessary tighten the slotted nut further or loosen it.

(Fig. 36)

36 Check if the backlash is 0.1...0.2 mm from the centre of the pinion shaft up to the measuring point (X) 42 mm. Correct by means of shims (6).

X

(Fig. 28, 37)

37

A

B

Rotate the shaft several times and check contact pattern (A). The tooth flanks shall be load-bearing at the centre and crown (C).

C

Make corrections (B) at the shims (14 and 6). After completing the correction, check backlash and correct if necessary.

(Fig. 14, 38)

204110

38 Secure the slotted nut (10), using an oblique punch, by forcing the shoulder into the groove of the bevel gear shaft.

10

(Fig. 39)

39

2.2.12

RHB ROLLANT 250 / 250 RC - 298 332.0

Drives Grease the dust lips of the shaft seal (9) and install shaft seal in the housing so it is flush.

(Fig. 40) 9

40 Secure the slotted nut (19), using an oblique punch, at three spots by forcing the shoulder into the respective groove of the shaft.

(Fig. 41)

19

41 Drive the cap (16) into the housing so it is flush.

16

(Fig. 42)

42 Drive the shaft seal (24) into the housing up to the stop.

24

(Fig. 43)

43

298 332.0 - RHB ROLLANT 250 / 250 RC

2.2.13

Drives Screw in the bleed valve.

5

7

Fill in the corresponding oil quantity.

Apply sealing compound (e.g. Atmosit) to the sealing face at the housing, put cover (5) in place, screw in bolts (7) and tighten them.

(Fig. 44)

44 Push guard (R) on the shaft. Mount guard (T) to the transmission with hexagon bolts M 8 x 16 8.8 and contact washers.

R

(Fig. 45)

T 45

Installing the angle drive Ensure the bushings (B) are in place in the bracket and insert bushings from the outside if necessary.

B

(Fig. 46) B

46 Suspend angle drive (G) in a lifting device and carefully lift it into the baler from below.

(Fig. 47)

G

2.2.14

47

RHB ROLLANT 250 / 250 RC - 298 332.0

Drives Insert the angle drive (G) into the bracket and fasten with hexagon bolts (S) M 12 x 40 10.9 from serial no. 725 01 596 and M 12 x 40 8.8 up to serial no. 725 01 595 and contact washers.

G

(Fig. 48) S

48 Press a new deep groove ball bearing (A), if previously removed, into the bearing housing (C) and install circlip (B).

A B

(Fig. 49) C

49 Place bearing housing (C) in position and drive it on the shaft up to the stop.

C Important!

The guard on the shaft must not be jammed.

(Fig. 50)

50

F

Check bushings (E) in chain wheel (F) and press in new bushings if necessary.

E

(Fig. 51)

51

298 332.0 - RHB ROLLANT 250 / 250 RC

2.2.15

Drives Slide on chain wheel (F) up to the stop.

(Fig. 52) F

52

Important!

On feed rake machines, slide on only one chain wheel (K) up to the stop.

(Fig. 53) K

53 Push chain wheel (H) on the shaft until it makes contact with chain wheel (F).

F

(Fig. 54)

H

54 Screw in hexagon bolt (N) M 16 x 40 8.8 with contact washer and washer (T) and tighten it. Install and tension roller chains (R), see section “Installing the roller drive (front)” and “Installing and tensioning the roller drive (top)”.

T N

(Fig. 55)

R 55

2.2.16

RHB ROLLANT 250 / 250 RC - 298 332.0

Drives Install brace (B) with bushing, hexagon bolt M 12 x 65 8.8, washer and new lock nut.

Install panel (A) and lower pick-up.

(Fig. 56) A

B 56

298 332.0 - RHB ROLLANT 250 / 250 RC

2.2.17

Drives DRIVE DIAGRAM Drives, left-hand side

2

1

6

7

8

204465

1 1 Roller drive, top 2 Roller drive, front 6 Pick-up drive 7 Cutting rotor/feed rotor drive 8 Drive for rollers 1, 2 and 16

298 332.0 - RHB ROLLANT 250 / 250 RC

2.3.1

Drives Drives, right-hand side

3

5

4

9

10

11

204466

2 3 Roller drive for tailgate 4 Twine wrapping drive 5 Net and twine wrapping drive 9 Wrapping drive 10 Twine wrapping drive 11 Feed auger drive

2.3.2

RHB ROLLANT 250 / 250 RC - 298 332.0

Drives DRIVE CHAINS, LEFT-HAND SIDE Removing the roller drive (top) Loosen lock nut (A).

A

Remove spring guide from the threaded rod and remove compression spring (B).

C

Remove chain-connect link and roller chain (C).

(Fig. 1) B

1 Drive gib head keys out of the chain wheels of roller 12 (G), roller 14 (E) and roller 15 (D).

F

Important!

G

The double chain wheel of roller 13 (F) can be removed only after removing roller chain (H) for “Roller drive (front)”.

H

E

(Fig. 2) D 2 Pull off corresponding chain wheel (G), (E) or (D).

(Fig. 2, 3)

E 3 Remove circlip located in front of the jockey sprocket (J).

Pull off jockey sprocket (J).

J

(Fig. 4)

4

298 332.0 - RHB ROLLANT 250 / 250 RC

2.4.1

Drives If required, remove circlip (L) and push deep groove ball bearing (K) out of the jockey sprocket.

L

K

(Fig. 5)

5 Unscrew the bolt located in front of the lever (M).

N

Pull off lever (M) along with jockey sprocket (N) and threaded rod (O).

M

(Fig. 6)

O 6 Remove circlip and washer located in front of the jockey sprocket.

Pull off jockey sprocket (N) and remove supporting ring.

(Fig. 7)

N 7 Remove circlip, spacer ring, washer and threaded rod (O) from lever (M).

(Fig. 8)

M O 8

2.4.2

RHB ROLLANT 250 / 250 RC - 298 332.0

Drives If required, push bushings (R) out of the lever (M) and press in new bushings.

(Fig. 9)

R M

R 9

Installing and tensioning the roller drive (top) S

Slide on the threaded rod (O), washer (T) and spacer ring (S).

T

Install circlip.

O

(Fig. 10)

10 Press on the jockey sprocket (N).

W

V

Place the washer (V) in position and install circlip (W).

N

(Fig. 11)

11 Slide on any removed chain wheels and insert gib head keys a little.

G

Align the chain wheels (G), (E) and (D) so that they are aligned with the double chain wheel (F) and drive in the gib head keys in this position.

F E

(Fig. 12)

D 12

298 332.0 - RHB ROLLANT 250 / 250 RC

2.4.3

Drives Slide washer (R) over the threaded rod (O).

Slide any removed washers and lever (M) on the stub and at the same time install the threaded rod in the bracket.

M

(Fig. 13)

O R 13 Check if the jockey sprocket is aligned with the chain wheels.

(Fig. 14)

14 If required, pull off lever (M) and change position by means of corresponding washers (Z).

Reinstall lever and check alignment one more time.

Z

Secure lever with bolt M 8 x 16 8.8, washer and contact washers.

(Fig. 13, 15)

15 Slide on jockey sprocket (J) and check alignment with the chain wheel, if necessary pull off jockey sprocket and change position by means of corresponding washers.

J

(Fig. 16)

16

2.4.4

RHB ROLLANT 250 / 250 RC - 298 332.0

Drives Secure jockey sprocket with washer and circlip.

(Fig. 17)

17 Slide compression spring (B) over the threaded rod and bolt on spring guide (F).

(Fig. 18)

B

F 18 Place roller chain (C) in position and join it with the chain-connect link.

(Fig. 19)

C

19 Tighten the spring guide (F) until the compression spring has reached the dimension (X) 140 mm.

Tighten lock nut (A).

(Fig. 20)

A X

F 20

298 332.0 - RHB ROLLANT 250 / 250 RC

2.4.5

Drives Removing the roller drive (front)

A

Loosen the set screw in the lock collar (A).

Loosen lock nut (B) and turn fully downwards.

Turn spring guide fully downwards.

Remove roller chain (C).

B

(Fig. 21)

C

21 Unscrew bolt (F) and remove lever (E).

Remove compression spring (D) and, if required, remove spring guide from the threaded rod.

D

To replace the jockey sprocket, the deep groove ball bearing and/or the bushings, see section “Roller drive (top)”.

(Fig. 22)

F E 22

Drive gib head key out of the chain wheel (G) and remove chain wheel.

(Fig. 23) G

23

Important!

The double chain wheel of roller 13 (H) and of roller 16 can only be removed after removing roller chain (J) of “Roller drive (top)”.

H J

(Fig. 24)

24

2.4.6

RHB ROLLANT 250 / 250 RC - 298 332.0

Drives To replace the chain wheel (K) on the transmission shaft of feed rake machines, unscrew the bolt and remove chain wheel.

(Fig. 25)

K 25 K

Important!

To replace the chain wheel (K) on the transmission shaft of rotor machines, remove roller chain (L) and chain wheel (M).

L

(Fig. 26) M

26

Installing the roller drive (front) H

Slide on chain wheel (G) and insert gib head key a little, but not entirely.

Align the chain wheel (G) with the chain wheel of roller 13 (H) and after obtaining this position, drive in gib head key.

(Fig. 27)

G

27 Slide lever (E) with the built-on threaded rod and jockey sprocket on the bearing pin.

E

N

Check alignment of the jockey sprocket with the chain wheels (N) and (K) and change position of set collar with corresponding washers if necessary.

K

Screw in bolt M 8 x 16 8.8 (P) with washer and contact washer and tighten it.

P

(Fig. 28)

28

298 332.0 - RHB ROLLANT 250 / 250 RC

2.4.7

Drives Screw the spring guide (T) on the threaded rod a little.

T

Slide the compression spring (D) over the spring guide.

(Fig. 29)

D

29 Place roller chain (C) in position and join with chain-connect link.

C

(Fig. 30)

30 Turn lock nut (B) upwards until the spring length has reached a dimension (X) = 290 mm.

T

Turn spring guide (T) down until it reaches the lock nut and tighten it.

(Fig. 31) X

B 31 Slide on set collar (A) and fasten it at a spacing (Y) of 35 mm from the mounting plate (L).

(Fig. 32) A Y

32

2.4.8

RHB ROLLANT 250 / 250 RC - 298 332.0

Drives Removing the cutting rotor/feed rotor drive Remove the cover.

Loosen lock nut (E).

Unscrew the spring guide from the threaded rod and remove compression spring (F).

(Fig. 33)

E F 33

Remove roller chain (G).

(Fig. 34)

G

34 To remove the lever (J) with jockey sprocket, remove roller chain (M), see section “Drive of rollers 1, 2 and 16”.

H

M

Unscrew bolt (H) and remove lever (J).

To replace the jockey sprocket, the deep groove ball bearing and/or the bushings, see sections “Removing the roller drive (top)” and “Installing and tensioning the roller drive (top)”.

J

(Fig. 35) 35 To replace the chain wheel (K), remove bracket (L) with pick-up, see section “Removing the pick-up”.

(Fig. 36) K

L

36

298 332.0 - RHB ROLLANT 250 / 250 RC

2.4.9

Drives To replace the chain wheel (C), unscrew bolt (D) M 16 x 40 8.8 and remove chain wheel.

C

(Fig. 37)

D

37

Installing and adjusting the cutting rotor/feed rotor drive Slide washer (B) over the threaded rod (A).

M

Slide lever (J) on the stub and at the same time insert the threaded rod (A) into the bracket.

J

(Fig. 38)

A

B 38 Check alignment of jockey sprocket with the chain wheel (K), and change position with corresponding washers if necessary.

Secure lever with bolt M 8 x 16 8.8, washer and contact washer.

Install roller chain (M).

K

(Fig. 38, 39)

39 Place roller chain (G) in position and join it with chain-connect link.

(Fig. 40)

G

40

2.4.10

RHB ROLLANT 250 / 250 RC - 298 332.0

Drives Slide on compression spring (F) and screw spring guide (T) on the threaded rod (A) until the spring length has reached the dimension (X) 140 mm.

E

Tighten lock nut (E).

T

(Fig. 41) X A F

41 Install cover (V).

(Fig. 42)

V

42

Removing the drive of rollers 1, 2 and 16 Remove cover.

Turn lock nut fully downwards.

R

Remove roller chain (R).

(Fig. 43)

43 Drive gib head key out of the chain wheels of roller 1 (D) and roller 2 (G) and pull off chain wheels.

B Important!

The double chain wheel of roller 16 (B) can only be removed after removing roller chain (C) of “Roller drive (front)”.

C

G

(Fig. 44)

D 44

298 332.0 - RHB ROLLANT 250 / 250 RC

2.4.11

Drives Remove spring guide (A) from the threaded rod (H) and remove compression spring (E).

Unscrew bolt ahead of the lever (F) and remove lever.

To replace the jockey sprocket (J), the deep groove ball bearing, the threaded rod (H) and the bushings, see section “Roller drive (top)”.

A

(Fig. 45)

E

H J

F 45

Installing and adjusting the drive of rollers 1, 2 and 16 Slide on chain wheels (D) and (G) and insert gib head keys a little.

B

Align chain wheels with the double chain wheel (B) and drive in gib head key in this position.

(Fig. 46)

G

D 46 Slide on lever (F) and check alignment of jockey sprocket (J) with double chain wheel (B) and chain wheel (G), change position by corresponding washers if necessary. Secure lever with bolt M 8 x 16 8.8, washer and contact washer

B J

F

(Fig. 47) G

47 Slide compression spring (E) on the threaded rod and turn on spring guide (A) to roughly half of its length.

(Fig. 48) A E

48

2.4.12

RHB ROLLANT 250 / 250 RC - 298 332.0

Drives Place roller chain (R) in position and join with chain-connect link.

(Fig. 49)

R

49 Turn lock nut (K) upwards until the spring length has reached the dimension (X) 140 mm.

Turn spring guide (A) down until it reaches the lock nut and tighten it.

A

(Fig. 50)

X

K 50 Install cover (V).

(Fig. 51)

E V

51

Removing the pick-up drive (left) F

Remove the guard.

D

Loosen the block tensioner (E) and remove roller chain (B).

Remove free wheel mechanism (C), chain wheel (F) and clutch with catch (D).

C

(Fig. 52) E B 52

298 332.0 - RHB ROLLANT 250 / 250 RC

2.4.13

Drives To replace the plain bearings (G) in the clutch (K), remove catch.

K

(Fig. 53)

G

53

H

To disassemble the free wheel mechanism, remove bolts (H) after unscrewing the nuts.

S

Remove disk (S) and remove hub (N) from the chain wheel (O).

H

(Fig. 54)

N H O 54

Installing the pick-up drive (left)

N

Insert hub (N) into the disk (S).

Insert pawl (P) and compression spring (M) and fill space with grease.

(Fig. 55)

P

M

S 55 Place chain wheel (O) over the hub (N).

O

(Fig. 56)

N

56

2.4.14

RHB ROLLANT 250 / 250 RC - 298 332.0

Drives Put disk (S) in place and fasten with hexagon bolts M 8 x 35 8.8 (H), contact washers and nuts.

S

H

(Fig. 57) H

H 57 Fasten catch (D) to the clutch (K) with hexagon bolt M x 60 8.8 (L), contact washer and lock nut.

L D

(Fig. 58)

K

58 Slide on clutch (K) with catch (D) and fasten with hexagon bolt M 10 x 25 8.8 (R) and contact washer (Fig. 59) K D

R

59 Slide on chain wheel (F) and fasten with disk 11 x 40 x 4 (T), contact washer and hexagon bolt M 10 x 25 (A).

F

(Fig. 60)

T A

60

298 332.0 - RHB ROLLANT 250 / 250 RC

2.4.15

Drives Check if bushing (P) and supporting rings (M) are in place on the drive shaft and slide on if necessary.

(Fig. 61) P M

61 Slide on free wheel mechanism (C) and fasten with disk 11 x 40 x 4 (H), contact washer and hexagon bolt M 10 x 30 8.8 (G).

C

(Fig. 62)

G H

62 Place roller chain (B) in position and join with chain-connect link.

Tension roller chain with block tensioner (E).

B

(Fig. 63)

E

63 Put guard (J) in place and fasten with hexagon bolts M 8 x 16 8.8 and contact washers.

(Fig. 64)

J 64

2.4.16

RHB ROLLANT 250 / 250 RC - 298 332.0

Drives Removing the intermediate drive of pick-up drive on rotor machines

R

Remove roller chain of pick-up drive.

Remove cover.

Remove roller chain (R) of cutting rotor/feed rotor drive and guide plate (A).

A

Remove clutch (B) with catch.

B

(Fig. 65) 65 Unscrew bolt of spur gear (D) and remove along with washer and supporting ring.

D

Drive the expansion pins out of the set collar (L).

Loosen the set screw in the lock collar (G) and drive off lock collar.

(Fig. 66) L

G 66 Loosen set screw in the lock collar (C) and drive off lock collar counter clockwise.

Remove lock collar bearing (E).

(Fig. 67) C

E 67 Pull shaft (W) far enough out of the rear lock collar bearing until spur gear (D), bushing and set collar can be removed.

H

F

D

Pull out shaft entirely and remove lock collar (H).

Remove lock collar bearing (F).

W

(Fig. 68)

68

298 332.0 - RHB ROLLANT 250 / 250 RC

2.4.17

Drives Installing the intermediate drive of pick-up drive on rotor machines Install new lock collar bearing (F) with mushroom head bolts M 10 x 20 x 12 8.8 (K), contact washers and nuts on the bracket.

K F

(Fig. 69)

69 Slide lock collar (D) on the shaft (W) and slide shaft into the lock collar bearing (F).

(Fig. 70) F

D W 70 Slide set collar (L), bushing (M) and spur gear (D) on the shaft.

D

(Fig. 71)

M L 71 Turn hexagon bolt M 10 x 25 8.8 (O) with contact washer, disk 11 x 40 x 4 (S) and supporting ring S 35 x 45 (J) into the shaft.

S J

Arrest spur gear and tighten hexagon bolt.

O

(Fig. 72)

72

2.4.18

RHB ROLLANT 250 / 250 RC - 298 332.0

Drives Attach set collar to the shaft using expansion pin (T).

Move shaft so that spur gear (D) is centred with spur gear (P).

P

Lock lock collar (G) and tighten set screw.

(Fig. 73) D

G

T 73 Slide lock collar (C), sheet-metal flanges (U) and lock collar bearing (E) on the shaft.

U E

(Fig. 74)

C

74 Fasten sheet-metal flanges with mushroom head bolts M 10 x 20 x 12 8.8 (Z), contact washers and nuts.

Z

Lock lock collar (C) and tighten set screw.

(Fig. 74, 75)

75 Install clutch (B) with catch.

Install roller chain (R), see section “Installing and adjusting the cutting rotor/feed rotor drive”.

R

Install guide plate (A).

Install roller chain for pick-up drive.

A

(Fig. 76) B

76

298 332.0 - RHB ROLLANT 250 / 250 RC

2.4.19

Drives DRIVE CHAINS/DRIVE BELTS ON RIGHT-HAND SIDE Removing the feed auger drive (right) C

Remove guard.

D

Loosen the block tensioner (D) and remove roller chain (H).

H

Remove chain wheels (C) and (E) and take off washer and bushings.

(Fig. 1) E 1

Installing the feed auger drive (right) Slide on bushings (F) and washer (G).

(Fig. 2)

F G

2 Slide on chain wheel (E).

E

Place washer (J) in position.

J

Screw in hexagon bolt M 10 x 25 8.8 (L) with contact washer and disk 11 x 40 x 4 (K) and tighten it.

(Fig. 3) K

L 3 Slide on chain wheel (C) and fasten it with hexagon bolt M 10 x 25 8.8 (P), disk 11 x 40 x 4 (N) and contact washer.

C

(Fig. 4) N P

4

298 332.0 - RHB ROLLANT 250 / 250 RC

2.5.1

Drives Install roller chain (H) and tension it with block tensioner (D).

D

(Fig. 5) H

5 Install guard (M) with hexagon bolts M 8 x 16 8.8 and contact washers.

(Fig. 6)

M 6

Removing the tailgate roller drive Remove guard and chain guard.

A

Loosen lock nut (A).

Remove spring guide from the threaded rod and remove compression spring (B).

B

Remove roller chain (C).

(Fig. 7)

C

7 Unscrew bolt (J) and pull off lever (D).

D

Remove jockey sprocket (E) if required.

E

To replace the jockey sprocket, threaded rod (K), deep groove ball bearing and/or the bushings, see sections “Removing the roller drive (top)” and “Installing and tensioning the roller drive (top)”.

J

(Fig. 8)

K

8

2.5.2

RHB ROLLANT 250 / 250 RC - 298 332.0

Drives To replace the corresponding chain wheel (F) e.g. of roller 5, drive out gib head key and pull off chain wheel.

(Fig. 9) F

9 To replace the chain wheel (G) on roller 8, unscrew bolt, pull off chain wheel and remove shims.

G Important!

Note thickness of shims.

(Fig. 10)

10

Installing the tailgate roller drive Slide on the removed chain wheels and insert gib head keys a little.

Align the chain wheels to each other and drive in gib head keys in this position.

(Fig. 11)

11 Slide on shims (H) removed from roller 8 and chain wheel (G).

G

Screw in hexagon bolt M 12 x 35 8.8 with washer 13 x 62 x 6 and contact washer and tighten it.

H

(Fig. 12)

12

298 332.0 - RHB ROLLANT 250 / 250 RC

2.5.3

Drives Slide washer over the threaded rod (K).

Slide removed washers and lever (D) on the stub.

D

Insert threaded rod into the bracket.

E

Slide on removed washers and jockey sprocket (E).

(Fig. 13)

K 13 Check alignment of chain wheel (G) and of jockey sprocket (M) with the chain wheels (L) and (N) and change the position by corresponding washers if necessary.

G L

Secure chain wheel (G) with hexagon bolt M 12 x 35 8.8, disk 13 x 62 x 6 and contact washer.

(Fig. 14) M N 14 Check alignment of jockey sprocket (E) with the chain wheel (L), and change the position by corresponding washers if necessary.

Secure jockey sprocket with circlip.

L

(Fig. 15)

E 15 Place roller chain (C) in position and join with chain-connect link.

(Fig. 16) C

16

2.5.4

RHB ROLLANT 250 / 250 RC - 298 332.0

Drives Slide compression spring (B) over the threaded rod and screw on spring guide (O) until the compression spring has reached the dimension (X) 140 mm.

A

Tighten lock nut (A).

(Fig. 17)

X B O

17 Install chain guard (P).

Danger!

P

Before screwing in the two front hexagon bolts M 8 x 20 8.8 with contact washers, open tailgate approx. 10 cm.

☞ Set the lever of the tailgate safety lock to the end position (to the rear).

18

(Fig. 18) Install guard (R).

(Fig. 19)

R

19

Important!

Fasten the brace on the guard to the frame with hexagon bolts M 8 x 16 8.8, contact washer and nut.

(Fig. 20)

20

298 332.0 - RHB ROLLANT 250 / 250 RC

2.5.5

Drives Removing and disassembling the tying drive Danger!

Pinch point!

☞ Whenever working on the open tailgate

H

and in the bale chamber, set the lever (H) of the tailgate safety lock to the end position (Z).

O Z 21

Before closing the tailgate, set the lever (H) to end position (O).

Open tailgate.

(Fig. 21)

Remove V-belt from the front V-belt pulleys.

Remove the earth cable (A) and the pipe clamp (B) from the support.

A

Pull electro-magnetic clutch cable out of the bar and disconnect connector.

(Fig. 22)

B

22 Hang out hook of the tension spring (D) from the jockey pulley bracket.

Remove V-belt (C).

C

(Fig. 23)

D

23

2.5.6

RHB ROLLANT 250 / 250 RC - 298 332.0

Drives Unscrew the nuts from the mushroom head bolts and remove support (E).

If required, remove V-belt pulley (K) from roller 13.

K

(Fig. 24)

E

24 Remove bracket (P) with jockey pulley mounted to it and remove deep groove ball bearing in the jockey pulley.

N

(Fig. 25)

D

25 Remove V-belt pulley (F) and jockey pulley (G).

K

If required, remove deep groove ball bearing from the jockey pulley (G).

Pull off V-belt pulley (K) of electro-magnetic clutch.

Carefully drive cone shaft out of the V-belt pulley (F).

(Fig. 26)

F G

26 Remove electro-magnetic clutch (J) and pull cable out of the rubber sleeve.

(Fig. 27)

J 27

298 332.0 - RHB ROLLANT 250 / 250 RC

2.5.7

Drives Pull both deep groove ball bearings (M) out of the bearing housing (L).

Remove bearing housing (L) if required.

(Fig. 28)

L M 28

Assembling and mounting the tying drive Push new deep groove ball bearing (W) into the jockey pulley (G) and secure with circlip (V).

G

W

(Fig. 29)

V

29 Insert hexagon bolt M 10 x 70 8.8 (T) with disk 13 x 40 x 6 (S) into the support.

T G

Slide on disk 13 x 40 x 6 (S), spacer tube (R) and jockey pulley (G).

Screw on new lock nut and tighten it.

(Fig. 30)

S S R 30

Insert hexagon bolt M 10 x 70 8.8 (T) with disk 13 x 40 x 6 (S) into the support.

H

Slide on disk 13 x 40 x 6 (S), spacer tube (R) and jockey pulley (G).

Screw on new lock nut and tighten it.

H

(Fig. 31) U L

Q 31

2.5.8

RHB ROLLANT 250 / 250 RC - 298 332.0

Drives Push the cables of the electro-magnetic clutch (J) through the rubber sleeve.

Install four hexagon bolts M 6 x 16 8.8 (O) and slide on washers (Y).

Place electro-magnetic clutch (J) in position on the support, screw on nuts and tighten them.

Y

(Fig. 32) J O 32 Install cone shaft (X) in the V-belt pulley (K).

(Fig. 33) K

X

33 Slide V-belt pulley (K) over the electro-magnetic clutch (J).

(Fig. 34)

J K 34 Slide on bushing (L) and insert parallel key (P).

Install hexagon bolt M 10 x 120 8.8 (Z). Slide on V-belt pulley (F), with the convex centre part facing outside and fasten with washer, contact washer and nut.

Z

L

(Fig. 35)

P F 35

298 332.0 - RHB ROLLANT 250 / 250 RC

2.5.9

Drives

A

Mount jockey pulley (N) to the bracket with hexagon bolt M 12 x 55 8.8 (A), bushing (B), washer and new lock nut.

B

(Fig. 36)

N 36 Insert flange sleeve (M) into the bracket (P).

Mount bracket with hexagon bolt M 10 x 28 8.8 (G), washer (R) and contact washer.

(Fig. 37)

P

M

G R

37 Mount V-belt pulley (K) to roller 13 with hexagon bolt M 10 x 90 8.8 (Q), contact washer and disk 10.5 x 40 x 6 (O) if previously removed.

K

(Fig. 38)

Q

W13 O

38 Mount the pre-assembled support (E) with mushroom head bolts M 10 x 25 8.8 (S), contact washers and nuts.

E

Important!

H

On standard version balers, also install bracket (H) with bale counter.

(Fig. 39) S 39

2.5.10

RHB ROLLANT 250 / 250 RC - 298 332.0

Drives Place V-belt (C) in position and hang in hook (H) of tension spring (D).

(Fig. 40) C

D

H

40 Connect the connector halves (L) on the cables of the electro-magnetic clutch.

Push the cable into the bar so it will not chafe.

L

(Fig. 41)

41 Attach cable with pipe clamp (B) at the side and with ring of earth cable (A) at the front of support.

Install V-belt on the front V-belt pulleys.

A

Close tailgate.

(Fig. 42) B

42

Removing and installing the net wrapping/ twine wrapping drives Net wrapping drive on standard version machines.

(Fig. 43)

43

298 332.0 - RHB ROLLANT 250 / 250 RC

2.5.11

Drives Net wrapping drive on comfort version machines.

(Fig. 44)

44

Important!

Only on comfort version machines: Slide the V-belt pulley (H) with free wheel mechanism so on the shaft of the pressure roller (G) that the free wheel mechanism rotates clockwise.

G H

Screw in hexagon bolt M 10 x 30 8.8 (S) with two contact washers and tighten it (hold the pressure roller tight while tightening).

S 45

(Fig. 45) Twine wrapping drive on standard version machines.

(Fig. 46)

46 Twine wrapping drive on comfort version machines.

Important!

M

To replace the V-belt pulley (M) with clutch, see section “Twine wrapping”.

Fasten V-belt pulley (N) with hexagon bolt M 10 x 30 8.8, contact washer and disk 11 x 40 x 4.

N 47

2.5.12

(Fig. 47)

RHB ROLLANT 250 / 250 RC - 298 332.0

Drives Net and twine wrapping drive on standard version machines.

Remove jockey pulleys (L), (A) and (B) if required.

L

For removing these V-belt pulleys, see corresponding section.

A

(Fig. 48)

B 48

Q

R

T

Insert bolt (Q) M 12 x 110 8.8 with washer 13 x 40 x 6 from the inside into the net wrapping side wall. Slide on washer 13 x 40 x 6 (T) and tube (R) from the outside.

L

Slide on jockey pulley (L) and fasten with washer and new lock nut.

(Fig. 49)

49 Mount jockey pulley (A) on the bracket (E) with hexagon bolt M 12 x 65 8.8 (K), joint tube (C), washer and new lock nut.

C A

K

B

Place jockey pulley (B) in position at the bracket with hexagon bolt M 12 x 60 8.8 (F), spacer tube (G) and washer 12.2 x 30 x 5 (D).

E

(Fig. 50) D F G

50 Mount bracket (E) with V-belt pulleys to bracket (O), using hexagon bolt (F).

(Fig. 50, 51)

F

O

E

51

298 332.0 - RHB ROLLANT 250 / 250 RC

2.5.13

Drives Hang tension spring (Z) into the bracket.

Hang hook (H) into the tension spring and into the rear bracket.

L

Tension V-belt by displacing the jockey pulley (L).

(Fig. 52)

H Z

52

2.5.14

RHB ROLLANT 250 / 250 RC - 298 332.0

3 Pick-up / Rollers

Pick-up / Rollers PICK-UP LIFT Removing the hydraulic pick-up lift Removing the hydraulic pick-up lift B

Slightly raise the pick-up and support safely.

A

In case of net wrapping, remove right-hand filler plate (A) in the net trough.

Remove bracket (B) with mounted net ramp.

(Fig. 1)

1 Only on comfort version machines: Remove twine wrapping drive V-belt (C).

(Fig. 2)

C

2 Loosen lock nut of hexagon bolt (D) and unscrew hexagon bolt from tension spring (E).

(Fig. 3)

D

E 3 Remove support tube (G) from lever.

Remove brace (F) on the right-hand and left-hand side from the respective lever.

(Fig. 4) F G

4

298 332.0 - RHB ROLLANT 250 / 250 RC

3.1.1

Pick-up / Rollers Drive expansion pins out of the lever (H) and pull off lever from the shaft.

Loosen the set screw in the set collar (J) and pull off set collar from the shaft.

J

Pull out shaft and remove plastic bearing.

(Fig. 5) H

5 To remove the tension spring (Z) and the hydraulic cylinder with support tube, remove support (K). To do this, remove module and/or modules and disconnect corresponding hydraulic lines from the ports.

Z D

Environment!

Collect leaking hydraulic oil and dispose of properly!

K

Important!

6

Pay attention to the orifice plate in the hydraulic line at the pressure relief valve (D).

(Fig. 6)

Installing the hydraulic pick-up lift Z

Hang in the tension spring (Z) if required.

Slide hydraulic cylinder (P) on the pin and connect hydraulic hose.

(Fig. 7)

P

7

3.1.2

RHB ROLLANT 250 / 250 RC - 298 332.0

Pick-up / Rollers Insert plastic bearing (A) so on the right-hand side that the thinner face faces forward.

A

(Fig. 8)

8 Slide in the shaft (W) from the right-hand side up to the stop.

(Fig. 9)

W

L 9 Insert plastic bearing (B) on the left-hand side so that the thinner face faces forward.

(Fig. 10)

B 10 Slide on set collar (J) and fasten it so that the shaft has no play, but can still be rotated.

Rotate shaft so that the mounting plate (L) faces the front.

J

Slide the lever (H) on the shaft, facing forward, and fasten with expansion pins on the shaft.

(Fig. 9, 11) H

11

298 332.0 - RHB ROLLANT 250 / 250 RC

3.1.3

Pick-up / Rollers Fasten the right-hand and left-hand brace (F) to the lever with hexagon bolt M 12 x 45 8.8 (T), bushing (R), washer and lock nut.

F T

(Fig. 12) R

12 Mount the cylinder support tube (S) to the lever.

Screw the hexagon bolt (D) into the tension spring (E).

D

Tension the relief tension spring. To do this, raise the pick-up fully.

M

Tension the tension spring until dimension (X) from the centre of pin to the top edge of the spring insert has been reached.

X

from machine serial no. 725 01 596 = 110 mm

E

S

up to machine serial no. 725 01 595 = 125 mm 13

Tighten lock nut (M).

(Fig. 13) On comfort version machines: Install V-belt (C) in case of twine wrapping.

(Fig. 14)

C

14 Hang the tension spring (Z) into the jockey pulley bracket.

(Fig. 15) Z

15

3.1.4

RHB ROLLANT 250 / 250 RC - 298 332.0

Pick-up / Rollers In case of net wrapping, install bracket (B) with mounted net ramp.

F

Insert right-hand filler plate (F) and fasten with wing-nuts.

(Fig. 16)

B

16 Mount support (K) on right-hand side if previously removed and connect the corresponding hydraulic lines.

K

A D

Caution!

Insert the orifice plate (D) previously removed into port (A) of the hydraulic line (C) from the pressure gauge.

C

Connect hydraulic line (C).

Install module and/or modules.

17 (Fig. 16, 17)

298 332.0 - RHB ROLLANT 250 / 250 RC

3.1.5

Pick-up / Rollers PICK-UP Removing the gauge wheel Unscrew bolt (7).

2

Pull the stub of supporting arm (2) out of the retainer in the pick-up.

(Fig. 1)

7 1 Disassembling the gauge wheel Unscrew the bolt (17) from the shaft on both sides.

Remove the wheel from the bracket.

(Fig. 2)

17

2 Remove circlip, washers and shims on the side ahead of the shaft (14).

14

Pull shaft with washers and shims out of the bearing.

Remove circlip, washers and shims from the shaft.

(Fig. 3)

3 Pull both deep groove ball bearings (13) out of the rim and remove spacer bushing.

(Fig. 4)

13 4

298 332.0 - RHB ROLLANT 250 / 250 RC

3.2.1

Pick-up / Rollers Unscrew bolt from the stub of the bracket (9).

2

R

Drive stub of the bracket out of the supporting arm (2) bearing with a suitable tube (R).

9

(Fig. 5)

5 Pull both deep groove ball bearings (3) out of the supporting arm.

(Fig. 6)

3

6

3.2.2

RHB ROLLANT 250 / 250 RC - 298 332.0

Pick-up / Rollers

5 2 1

4

7 8

6

3

3 9

15 16 17

12

10 11

14

10

12

19 18

13

11

13

204486

7 Gauge wheel, disassembled 1 Tyre with inner tube 16 x 6.50-8 6PR C 2 Right-hand supporting arm Left-hand supporting arm 3 Deep groove ball bearing 6005-2RS 4 Washer 5 Hexagon bolt M 12 x 20 8.8 A3C 6 Contact washer A 12 7 Hexagon bolt M 12 x 25 8.8 A3C 8 Contact washer B 12 9 Bracket 10 Circlip 25 x 1.2 11 Washer 12 Shim 25 x 35 x 0.5 13 Deep groove ball bearing 6205-2RS 14 Shaft D 25 x 193 15 Washer 16 Contact washer A 12 17 Hexagon bolt M 12 x 20 8.8 A3C 18 Rim 5.50 A x 8 19 Spacer bushing

298 332.0 - RHB ROLLANT 250 / 250 RC

3.2.3

Pick-up / Rollers Assembling the gauge wheel Push the deep groove ball bearing (13) into the rim up to the stop on one side.

13

Insert the spacer bushing (19) from the other side and push in deep groove ball bearing (13) up to the stop.

19

(Fig. 8)

8 Install circlip (10) on one side in the groove of shaft (14).

11 12

14

Slide on washers (11) and shims (12).

Slide shaft into the deep groove ball bearings in the rim.

(Fig. 9)

10 9 Slide shims (12) and washers (11) over the shaft on the other side.

(Fig. 10)

11 12

10 Insert circlip (10) into the groove of the shaft.

(Fig. 11)

10

11

3.2.4

RHB ROLLANT 250 / 250 RC - 298 332.0

Pick-up / Rollers Push both deep groove ball bearings (3) into the supporting arm (2) up to the stop.

3

2

(Fig. 12)

12 Push the stub on bracket (9) into the deep groove ball bearings of the supporting arm (2).

5

4

Important!

9

Observe correct installation position!.

2 Screw in bolt (5) with washer (4) and contact washer and tighten it.

(Fig. 13) 13 Insert rim into the bracket.

Screw in bolt (17) with washer and contact washer on both sides and tighten it.

(Fig. 14)

17

14

Removing the short crop baffle A

Remove pick-up crop guard.

C

Unscrew the nuts and pull out hexagon bolts (A).

Remove short crop baffle (B).

B

(Fig. 15) D

15

298 332.0 - RHB ROLLANT 250 / 250 RC

3.2.5

Pick-up / Rollers Installing the short crop baffle Check supports (C) and install new supports with mushroom head bolts M 8 x 25 8.8 (D), contact washers and nuts if necessary.

Install bushings (E) into the levers of the short crop baffle (B) from the inside.

Place short crop baffle in position and fix it to the pick-up frame with hexagon bolts M 10 x 30 8.8 (A), contact washers and nuts.

E

B

Install pick-up crop guard.

16

(Fig. 15, 16)

Replacing the spring tine Unscrew top and bottom fastening bolts of the corresponding stripper loop (G).

Pull stripper loop out of the bottom fastening, unhook from the top fastening and remove to the front.

G

(Fig. 17)

17 Unscrew the fastening bolt (S) while backing up the nut and remove spring tine (F).

(Fig. 18) F

S

18

Removing the pick-up and auger Remove guard and roller chain on the corresponding side.

Remove chain wheel.

Drive auger out of the deep groove ball bearing with a plastic-tip hammer.

Lift auger out of the feed channel.

(Fig. 19) 19

3.2.6

RHB ROLLANT 250 / 250 RC - 298 332.0

Pick-up / Rollers Remove circlip (1) ahead of the outside deep groove ball bearing.

(Fig. 20)

1

20 Pull out outside deep groove ball bearing (2).

(Fig. 21) 2

21 Remove the inside deep groove ball bearing (2) in the same way.

(Fig. 22) 2

22 Pick-up and auger, disassembled 5

1

2

3 2

1 2 3 4 5 6

1

Circlip 62 x 2 Deep groove ball bearing 6206-2 RS Bushing Auger, left Shim 30 x 42 x 0.5 Shim 30 x 42 x 1.0

(Fig. 23)

6 204596

298 332.0 - RHB ROLLANT 250 / 250 RC

7

23

3.2.7

Pick-up / Rollers Installing the pick-up and auger Install inside deep groove ball bearing (2) and circlip (1).

2

1

Drive the deep groove ball bearing carefully up to the circlip from the outside.

(Fig. 24)

24 Install bushing (3) and outside deep groove ball bearing (2) and secure with circlip.

3

(Fig. 25)

2

25 Install auger (5) from the inside and drive it into the deep groove ball bearing with a plastic-tip hammer up to the stop.

(Fig. 26) 5

26 Slide on chain wheel (A) and fasten with hexagon bolt M 10 x 25 8.8 (C), contact washer and washer 11 x 40 x 4 (K).

(Fig. 27)

A K C

27

3.2.8

RHB ROLLANT 250 / 250 RC - 298 332.0

Pick-up / Rollers Install roller chain (B) and join with chain-connect link.

Tension roller chain with block tensioner (E).

B

(Fig. 28)

E

28 Place guard (J) in position and fasten with hexagon bolts M 8 x 16 8.8 and contact washers.

If the right-hand auger has been replaced, install roller chain and guard in the same way.

(Fig. 29)

J 29

Replacing the left-hand drive shaft lock collar bearing 13

Remove roller chain and free wheel mechanism.

22

Loosen set screw in lock collar (22), drive off lock collar counter clockwise and remove it.

Unscrew bolts, pull off bearing shell (13) with lock collar bearing and remove supporting ring.

Remove lock collar bearing from the bearing shell.

30

Important!

The bolts have been installed with liquid locking compound and are therefore tightly seated.

(Fig. 30, 57)

298 332.0 - RHB ROLLANT 250 / 250 RC

3.2.9

Pick-up / Rollers Slide on supporting ring (24).

(Fig. 31, 57) 24

31 Slide on lock collar bearing with bearing shell (13).

13

Install bolts (14) of lock collar bearing flange with liquid locking compound (DELO-ML 187) and tighten them, install lock collar (22).

22

Install free wheel mechanism and roller chain.

(Fig. 32, 57)

14 32

Replacing the right-hand drive shaft lock collar bearing 3

Remove roller chain for feed auger and chain wheel.

Loosen set screw in lock collar (3), drive off lock collar clockwise and remove it.

(Fig. 33, 57)

33 Remove outside sheet metal plate (4) (four bolts on the inside and eight on the outside).

(Fig. 34, 56)

4

34

3.2.10

RHB ROLLANT 250 / 250 RC - 298 332.0

Pick-up / Rollers Spannringlager (4) abbauen.

Stützscheibe bei Bedarf von der Welle ziehen.

4

(Fig. 35, 57)

35 Slide on supporting ring.

Install lock collar bearing and lock collar (3).

2

Fix outside sheet metal plate (4) with eight mushroom head bolts (2) on the outside and with four hexagon bolts (A) on the inside.

A

Install feed auger chain wheel and roller chain.

4

3

(Fig. 36, 56)

36

Removing the pick-up Lower the pick-up fully.

Remove short crop baffle if fitted.

Unscrew hexagon bolt (C) on the cutting rotor/feed rotor drive.

(Fig. 37) C

37 Unscrew three nuts (D) of the mushroom head bolts and unscrew two hexagon bolts (E) on the right-hand bracket.

D

Important!

The two hexagon bolts have been installed with liquid locking compound and are therefore tightly seated.

E

(Fig. 38) 38

298 332.0 - RHB ROLLANT 250 / 250 RC

3.2.11

Pick-up / Rollers Support pick-up with a pallet truck or a similar vehicle.

Remove brace (F) on the left-hand and right-hand side from the transverse tube (G).

F

(Fig. 39)

G

39 Pull complete pick-up away from under the baler to the left.

(Fig. 40)

40

Mounting the pick-up Place complete pick-up in position above the cutting rotor/feed rotor drive.

Screw in hexagon bolt M 16 x 75 8.8 (C) with contact washer (H) and washer (I) and tighten it.

(Fig. 41)

C

H

I

41 Place right-hand bracket (J) in position on the pick-up.

J

Install hexagon bolts M 10 x 20 8.8 (E) with liquid locking compound (DELO-ML 187) and contact washer (K) and tighten it. To do this, align threaded plate.

K

(Fig. 42) E

42

3.2.12

RHB ROLLANT 250 / 250 RC - 298 332.0

Pick-up / Rollers Insert plate (L) and fasten mushroom head bolts M 10 x 25 8.8 (D) with contact washers and nuts.

(Fig. 43) D L

43 Fasten right-hand and left-hand brace (F) to the transverse tube (G) with hexagon bolt M 12 x 25 8.8 (M), bushing (N), washer and lock nut.

F

M

(Fig. 44)

N G

44

Removing the cam track Remove pick-up.

Remove pick-up drive (left-hand).

Remove feed auger drive (right-hand).

Remove outside sheet metal plate on right-hand (4) and left-hand side (6) (eight bolts on the outside and four on the inside each).

4

(Fig. 45, 56)

45

298 332.0 - RHB ROLLANT 250 / 250 RC

3.2.13

Pick-up / Rollers Unscrew the top and bottom fastening bolts of all stripper loops (5).

Pull stripper loops out of their bottom fastening, hook out of the top fastening and remove to the front.

(Fig. 46, 56)

5 46 Hang drive shaft into a suitable lifting device.

Unscrew the nuts (G) from all bottom fastening bolts of the pick-up frame and remove bolts.

G

(Fig. 47)

47 Unscrew the nuts (H) from all fastening bolts of the pick-up frame on the left-hand side and remove fastening bolts.

H

(Fig. 48)

48 Unscrew the nuts (O) from all fastening bolts of the pick-up frame on the right-hand side and remove fastening bolts.

O

(Fig. 49)

49

3.2.14

RHB ROLLANT 250 / 250 RC - 298 332.0

Pick-up / Rollers Lift pick-up frame with mounted drive shaft out of the base frame and lower to the ground.

Remove lock collar (3) and lock collar bearing (5) on the right-hand side.

(Fig. 50, 57) 5

3 50 Remove lock collar and bearing shell (13) with lock collar bearing on the left-hand side.

Important!

13

The bolts have been installed with liquid locking compound and are therefore tightly seated.

Lift drive shaft out of the pick-up frame with a suitable lifting device.

51

(Fig. 51, 57) Remove cam track (12) from the guide rollers.

(Fig. 52, 57)

12

52

Removing the guide rollers 19

Remove cam track.

20

Remove circlip (20) ahead of guide roller (19).

Pull off guide roller.

(Fig. 53, 57)

53

298 332.0 - RHB ROLLANT 250 / 250 RC

3.2.15

Pick-up / Rollers Removing the tine carrier Remove cam track.

Unscrew fastening bolts of flange bearings (6) on the right-hand and left-hand side.

6

Important!

The fastening bolts have been installed with liquid locking compound and are therefore tightly seated.

16 54

Remove tine carrier (16).

(Fig. 54, 57)

Pull off flange bearing (6) on both sides.

To replace the tine carrier, remove guide roller (19) and all spring tines (18).

18

(Fig. 55, 57) 6 19

55

Removing the drive shaft Remove all tine carriers.

Pull off supporting ring from the drive shaft on both sides.

3.2.16

RHB ROLLANT 250 / 250 RC - 298 332.0

Pick-up / Rollers

1

2 3 3 3

4

6 3 5

3

3 205141

56 Pick-up, disassembled 1 Pick-up frame 2 Mushroom head bolt M 8 x 20 x 13 8.8 A3C Mushroom head bolt M 8 x 25 8.8 A3C Hexagon nut M 8 Contact washer B 8 3 Hexagon bolt M 8 x 20 8.8 A3C 4 Outside sheet metal plate, right 5 Stripper loop 6 Outside sheet metal plate, left

298 332.0 - RHB ROLLANT 250 / 250 RC

3.2.17

Pick-up / Rollers

1

2

24

5

3 4

4

6

8 7 7

6 8

9

10

12

13

14

11

15

10 25 26

16 24

18

22

19 17

23

21

20

205142

57 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

16 17

18 19 20 21 22 23 24

Flange ball bearing PEA 207 Set screw M 8 x 10 Lock collar 35 Sheet-metal flange RB Y 207 Lock collar bearing YEN 207 Flange bearing Contact washer A 8 Hexagon bolt M 8 x 20 8.8 A3C Drive shaft Contact washer A 10 Hexagon bolt M 10 x 25 8.8 A3C Cam track Bearing shell Hexagon bolt M 10 x 45 10.9 A3C Hexagon bolt M 10 x 25 8.8 A3C Hexagon nut M 10 8 A3C Contact washer A A 10 Tine carrier Cheese-head screw M 8 x 25 10.9 A3C Cheese-head screw M 8 x 35 10.9 Lock nut VM 8 Contact washer A 8 Spring tine Guide roller 12 x 35 x 15 Circlip 12 x 1 Lock collar bearing YEN 207 Lock collar 35 Set screw M 8 x 10 Supporting ring S 35 x 45

3.2.18

25 Inside ring IR 25 x 30 x 26,5 26 Snap ring A 25

RHB ROLLANT 250 / 250 RC - 298 332.0

Pick-up / Rollers Mounting the tine carrier 16

nstall tine carrier (16) with flange bearing (6).

6

Screw in bolts with liquid locking compound (DELO-ML 118) and tighten them.

(Fig. 57, 58)

58 Slide supporting ring (24) over the drive shaft on both sides.

(Fig. 57, 59)

24 59

Mounting the cam track 19

H

Grease contact face (H) of the cam track (12).

Install cam track so that the guide rollers (19) are in the contact face.

(Fig. 57, 60) 12

19 19 60 Insert the pre-assembled drive shaft (9) with the cam track into the pick-up frame (1), using a suitable lifting device.

(Fig. 56, 57, 61)

9

1

298 332.0 - RHB ROLLANT 250 / 250 RC

61

3.2.19

Pick-up / Rollers Install lock collar bearing and lock collar on the right-hand side.

Place bearing shell (13) with lock collar bearing in position on the left-hand side.

13

Screw in bolts with liquid locking compound (DELO ML 118) and tighten them.

Mount lock collar.

(Fig. 62)

62 Hang pick-up frame in suitable lifting device at the drive shaft.

Insert pick-up frame (1) into the base frame (B).

Fasten the pick-up frame to the bottom of the base frame with mushroom head bolts, contact washers and nuts and at the side with hexagon bolts, contact washers and nuts.

1

(Fig. 63)

B

63 4

Mount all stripper loops (5) and outside sheet metal plate (4) on the right-hand and left-hand side.

5

Mount free wheel mechanism to the drive shaft on the left-hand side.

Slide the bushings on the drive shaft on the right-hand side and mount chain wheel and roller chain.

Mount pick-up.

(Fig. 64)

64

3.2.20

RHB ROLLANT 250 / 250 RC - 298 332.0

Pick-up / Rollers CUTTING/FEED UNIT Removing the cutting rotor/feed rotor Remove the pick-up.

Remove the cutting rotor/feed rotor drive.

Remove mechanical or hydraulic backwinder.

Remove bushing (B), chain wheel (K) and spur gear (S) with shims.

S

Unscrew nuts from the bolts and remove angle plate (W).

B

(Fig. 1)

W

K 1 Loosen both set screws in the lock collar bearing (13).

(Fig. 2, 9)

13

2 On balers with lubricating bearings, remove blue lubrication line (V).

14

Unscrew fastening bolts (14) and remove bearing (12).

(Fig. 3, 9)

12 V 3

298 332.0 - RHB ROLLANT 250 / 250 RC

3.3.1

Pick-up / Rollers Loosen set screw in lock collar (T), drive off lock collar counter clockwise and remove it.

N T

Remove lock collar bearing (N) and pull off sheet-metal flange with bracket (H).

(Fig. 4)

H 4

L

Remove black lubrication line (L) on balers with lubricating bearings.

3

Loosen the set screw in lock collar (1), drive off lock collar counter clockwise and remove it.

Remove lock collar bearing (3).

1

(Fig. 5, 9)

5 Place a suitable tube on the right-hand and left-hand rotor shaft, lift cutting rotor/feed rotor out of its brackets and remove from under the baler.

Important!

Lift evenly on both sides in order to avoid jamming.

(Fig. 6) 6 Disassembling the cutting rotor/feed rotor Remove the anti-wrapping guard on the left-hand side (9) and the ring (10).

9

(Fig. 7, 9)

10

7

3.3.2

RHB ROLLANT 250 / 250 RC - 298 332.0

Pick-up / Rollers Remove anti-wrapping guard on right-hand side (5).

(Fig. 8, 9)

5 8

298 332.0 - RHB ROLLANT 250 / 250 RC

3.3.3

Pick-up / Rollers

2

1

3

2

4

5

8

6

7 9

10 11

12

13

7 14

205158

9 Cutting rotor/feed rotor, disassembled 1 Lock collar 50 2 Flange housing Elbow union Ferrule Threaded stub Flange Sheet-metal flange RB Y 210 3 Lock collar bearing YEN 210-S 4 Disk 5 Anti-wrapping guard 6 Locking bolt M 12 x 30 8.8 A3C 7 Contact washer A 12 8 Rotor 9 Anti-wrapping guard 10 Ring 11 Shim 63 x 80 x 1 12 Bearing Elbow union Ferrule Threaded stub Bearing shell 13 Clamping bearing PSD212-S 14 Locking bolt M 12 x 50 8.8 A3C

3.3.4

RHB ROLLANT 250 / 250 RC - 298 332.0

Pick-up / Rollers Assembling the cutting rotor/feed rotor Slide right-hand anti-wrapping guard (5) over the shaft.

(Fig. 9, 10)

5 10 Slide ring (10) on the rotor with the convex side up to the stop.

Slide left-hand anti-wrapping guard (9) over the shaft.

9

(Fig. 9, 11)

10 11

Installing the cutting rotor/feed rotor Position the pre-assembled cutting rotor/feed rotor in front of the feed channel.

Place a suitable tube over the rotor shaft on the right-hand and left-hand side.

Lift cutting rotor into the receivers of the feed channel.

Important!

12

Lower evenly on both sides in order to avoid jamming.

(Fig. 12)

298 332.0 - RHB ROLLANT 250 / 250 RC *

3.3.5

Pick-up / Rollers Install disk (4) on right-hand side.

Mount lock collar bearing (3).

4

(Fig. 9, 13)

3 13 Arrest lock collar (1) clockwise and tighten set screw.

L

On balers with lubricating bearings fasten black lubricating line (L).

1

(Fig. 14)

14 Slide on bracket (H) with lock collar bearing (N).

N

Arrest lock collar clockwise and tighten set screw.

(Fig. 15)

H 15 Slide on lock collar bearing with bearing (12).

14

Install hexagon bolts (14) and tighten them.

Tighten both set screws.

On balers with lubricating bearings mount blue lubricating line (V).

(Fig. 9, 16)

12

V

16

3.3.6

RHB ROLLANT 250 / 250 RC - 298 332.0

Pick-up / Rollers Slide on removed shim (P) and spur gear (S).

(Fig. 17)

P

S 17 Slide on removed shim (M) and chain wheel (K).

(Fig. 18)

M

K 18 Check alignment of chain wheel (K) with chain wheel (R) and change position by corresponding washers if necessary.

(Fig. 19)

K

R

19 Fasten angle plate (W) with five mushroom head bolts M 8 x 24, contact washers and hexagon nuts.

Slide on removed shims (O) with bushing (B).

O

Mount mechanical or hydraulic backwinder.

Mount cutting rotor/feed rotor drive.

Mount pick-up.

(Fig. 20)

W B 20

298 332.0 - RHB ROLLANT 250 / 250 RC *

3.3.7

Pick-up / Rollers Removing the scraper of cutting rotor/feed rotor Danger!

Whenever working on the open tailgate and in the bale chamber, set the lever (H) of the tailgate safety lock to end position (Z).

H O

Before closing the tailgate, set lever (H) to end position (O).

Z

Open tailgate.

21 (Fig. 21) Unscrew all bolts (S).

Remove scraper and shimmings.

S

(Fig. 22)

S

22

Installing the scraper of cutting rotor/feed rotor

A

Install scraper (A). Using the shimmings (B), align the scraper to be centred with the rotor tines.

B

Fasten scraper with hexagon bolts M 12 x 35 8.8 and contact washers.

(Fig. 23)

23

3.3.8

RHB ROLLANT 250 / 250 RC - 298 332.0

Pick-up / Rollers Removing the knife shaft Danger!

Danger of injury when working on the cutting unit! Always wear gloves!

Pull the lever (21) out of its holder on the right-hand side and swing to the front.

21

(Fig. 24, 32) 24 Remove the knives from the rear or from the front.

Important!

When removing the knives from the front, remove pick-up crop guard.

(Fig. 25)

25 Unscrew lock nut and remove hexagon bolt (25) with washer (26).

(Fig. 26, 32) 26

25

26 Pull out eccentric shaft (22) to the right-hand side.

(Fig. 27, 32) 22

27

298 332.0 - RHB ROLLANT 250 / 250 RC *

3.3.9

Pick-up / Rollers Pull out top and bottom cotter pin (18) on the left-hand and right-hand side.

Remove washers (17) and hydraulic cylinder (15).

(Fig. 27, 32)

17 15

18

28 Unscrew nut (M) on the right-hand and left-hand side and remove washer with bushing, at the same time lowering the knife carrier.

(Fig. 29) M

29 Support knife shaft in the centre (e.g. pallet truck).

27

4

Unscrew nut (N) on the right-hand and left-hand side.

N

Remove bracket (27) on right-hand side.

Unscrew bolts (4) on the right-hand and left-hand side and lower knife shaft with mounted parts.

Pull out knife shaft with knife carrier and springs from below the baler to the side.

(Fig. 30, 32)

30 Hang out tension springs (14) at the knife carrier (1) and knife lever (13).

1

Unscrew the hexagon bolt on left-hand and right-hand side and remove both flanges.

14

Pull off knife lever and tube from the shaft.

(Fig. 31, 32)

13 31

3.3.10

RHB ROLLANT 250 / 250 RC - 298 332.0

Pick-up / Rollers

2

3

27

4

7

1

8

15 14

10 11 12 13 14

5 6

16 2

3 18

8 9

17

4 7

19 20 26 21

5

22

6

23 24 26

25

205179

Knife shaft, disassembled 1 Knife carrier 2 Bushing 3 Hexagon bolt M 12 x 30 8.8 A3C Contact washer A 12 4 Hexagon bolt M 12 x 20 8.8 A3C Hexagon nut M 12 Contact washer A 12 5 Hexagon bolt M 16 x 25 8.8 A3C 6 Contact washer A 16 7 Flange 8 Tube 9 Shaft D50 x 1188 10 Hexagon bolt M 12 x 45 8.8 A3C 11 Lock nut VM 12 12 Roller 13 Knife lever 14 Tension spring 15 Hydraulic cylinder 16 Non-return valve 17 Washer 18 Cotter pin 4 x 22 19 Hexagon bolt M 8 x 70 8.8 A3C Lock nut VM 8 Washer 8.5 x 30 x 5 20 Compression spring 21 Lever 22 Eccentric shaft

298 332.0 - RHB ROLLANT 250 / 250 RC

23 Dummy knife Retrofit kit 24 Knife 25 Hexagon bolt M 8 x 25 8.8 A3C Lock nut VM 8 Washer 8.5 x 30 x 5 26 Washer 8.5 x 30 x 3 27 Stop

32

3.3.11

Pick-up / Rollers Installing the knife shaft 7

Slide tube (8) on shaft (9) and mount right-hand flange (7) with contact washer (6) and hexagon bolt (5).

8 6

5

(Fig. 32, 33)

9

33 Slide on all knife levers (13) in the correct order and mount tube (8) and left-hand flange with contact washer and hexagon bolt (25).

8

Important!

When tightening the hexagon bolt, ensure that both flanges have the same position.

13 (Fig. 32, 34) 34 Hang tension springs (14) in at knife carrier (1) and knife lever (13).

(Fig. 32, 34, 35) 1 14

35 Roll the shaft with knife carrier below the baler (e.g. using a pallet truck) and lift it to the receiver of the rotor housing.

Insert two hexagon bolts (4) on the left-hand side and fasten with contact washers and hexagon nut.

4

(Fig. 32, 36)

36

3.3.12

RHB ROLLANT 250 / 250 RC - 298 332.0

Pick-up / Rollers Install two hexagon bolts (4) on the right-hand side and fasten with contact washers and hexagon nuts. Mount the stop (27) as well at the front hexagon bolt.

27

4

(Fig. 32, 37)

37 Raise the knife carrier and fasten on the right-hand and left-hand side with hexagon bolts (3), bushings (2), contact washers and hexagon nuts.

3

(Fig. 32, 38) 2

38 Mount hydraulic cylinder (15) and secure with washer and new cotter pin.

(Fig. 32, 39)

15

39 Install eccentric shaft (22) from the right-hand side.

(Fig. 32, 40)

22

40

298 332.0 - RHB ROLLANT 250 / 250 RC

3.3.13

Pick-up / Rollers Install hexagon bolt (25) with washer (26) on the left-hand side and fasten with washer and hexagon nut.

(Fig. 32, 41) 26

25

41 Install knife, swing the lever (21) to the rear and let it catch.

To adjust the knife height, please refer to the Operator’s manual.

21

(Fig. 32, 42)

42

3.3.14

RHB ROLLANT 250 / 250 RC - 298 332.0

Pick-up / Rollers ROLLERS 12

13

11

Removing roller 3

10

14

9 8

15

Important!

7

The rollers 1, 2, 4, 5, 6, 7, 12, 13, 14, 15 and 16 must be replaced in the same way.

6

16

Any deviations are pointed out separately.

5 1 2 205223

3

Replacing the rollers 8, 9 and 10 is described in section ìSwinging segmentî.

4

1

Roller 11 is described separately.

Danger!

Whenever working on the open tailgate and in the bale chamber, set the lever (H) of the tailgate safety lock to end position (Z).

H

Before closing the tailgate, set the lever (H) to end position (O).

O Z

Open tailgate approx. three quarters.

2

Remove “Tailgate roller drive” and “Roller drive, front” roller chains.

Important!

To remove other rollers, remove corresponding roller chain on the left-hand side.

(Fig. 1, 2)

To remove and install roller 13, remove V-belt pulley (A) and for roller 14, remove support (B).

(Fig. 3) A

B

298 332.0 - RHB ROLLANT 250 / 250 RC

3

3.4.1

Pick-up / Rollers To remove and install roller 15 on comfort version machines with twine wrapping, remove V-belt pulley (D) and for roller 16, remove support (E).

D

Caution!

F

E

Before removing support (E), support the raised tailgate safely.

4

To remove support (E), dismantle modules and disconnect corresponding hydraulic lines from the connections. Plug connections with plugs.

Environment!

Collect leaking hydraulic oil and dispose of properly.

Important!

Pay attention to orifice plate in the L-shaped line (F).

(Fig. 4)

Remove roller guard.

Drive gib head key out of the chain wheel (G) and pull chain wheel (G) off of the roller.

G

(Fig. 5)

5 On round balers with central lubrication system, remove lubricating line (J).

3

Loosen the set screw in lock collar (1), drive off and remove lock collar.

Remove lock collar bearing (3).

1

(Fig. 6)

J 6

3.4.2

RHB ROLLANT 250 / 250 RC - 298 332.0

Pick-up / Rollers Remove cover (19) and washer on the non-drive side.

Important!

Note thickness of possibly mounted washers.

14 (Fig. 7) 19

7 If a central lubrication system is provided, remove lubricating line as well as closed cover (19) and washer (12).

12

Unscrew bolt (14) from the roller.

19

(Fig. 7, 8)

14

8 Pull roller (8) to the rear on the non-drive side and remove roller completely.

(Fig. 9)

8

9 Remove anti-wrapping guard on the drive side.

Force off the anti-wrapping guard (15) with two bolts on the other side (the deep groove ball bearing (10) and the seal will also be forced off by this operation).

10

Clean roller thoroughly from inside, using a steam cleaner.

15

(Fig. 10)

10

298 332.0 - RHB ROLLANT 250 / 250 RC

3.4.3

Pick-up / Rollers Straighten both ends of the roller body. To do this, drive straightening plate (P) (self-manufactured) in up to the stop.

P

Push out the straightening plate with bolts M 16 x 60 if required via two opposed threaded bores.

(Fig. 11, 12)

11 Straightening plate (self-manufactured).

(Fig. 12) 4x M16

R

10

0

00

ø2

P

34

5

290

310

ø 70x ø 65

ø 70 ø 246 ø 248.5 205230

3.4.4

12

RHB ROLLANT 250 / 250 RC - 298 332.0

Pick-up / Rollers

1

6

2

3

4

3

5

7 8

17 18

9

13

12

10 11

19

14

15 13 16 205232

13 Roller 3, disassembled 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19

Lock collar 50 Set screw M 8 x 10 Sheet-metal flange RB Y 210 Lock collar bearing YEN 210-S Anti-wrapping guard Hexagon bolt M 12 x 35 8.8 A3C Contact washer A 12 Roller 3 Seal Deep groove ball bearing 6206-2RS C3 Deep groove ball bearing 6206-RS C3 Washer 11 x 40 x 4 Washer Contact washer A 10 Hexagon bolt M 10 x 25 8.8 A3C Anti-wrapping guard Hexagon bolt M 10 x 30 8.8 A3C Flange * Flange housing * Cover * Elbow union Ferrule Threaded stub

*May be lubricated

298 332.0 - RHB ROLLANT 250 / 250 RC

3.4.5

Pick-up / Rollers Installing roller 3 Place anti-wrapping guard (5) in the roller on the drive side.

(Fig. 14)

5

14 Install new seal (9) with grease and new deep groove ball bearing (10) in the new anti-wrapping guard (15).

15

10

(Fig. 15) 9

15 Drive deep groove ball bearing (10) on the roller on the non-drive side and push anti-wrapping guard (15) into the roller up to the stop.

(Fig. 16) 15

10 16 Insert shaft (W) of roller 3 into the right-hand receiver.

Important!

3

Insert stubs of rollers 4, 5, 6 and 7 also into the right-hand receiver.

W

Insert stubs of rollers 1, 2, 12, 13, 14, 15 and 16 into the left-hand receiver.

(Fig. 17) 17

3.4.6

RHB ROLLANT 250 / 250 RC - 298 332.0

Pick-up / Rollers Screw in the hexagon bolt (14) with washer (11) and contact washer (13) on the non-drive side until the bolt holds the roller.

(Fig. 13, 18)

14

18 Raise the roller slightly, screw two threaded pins M 10 x 90 (B) into the anti-wrapping guard and pull anti-wrapping guard to the outside, now tighten bolt (14).

12 14

19

Place washer (12) and cover (19) in position and fasten with bolts (16) and contact washers.

Important!

B

In case of lubricating bearings, fill cover with grease K2K (177 554 0).

19 In case of lubricating bearings, remove guard ring (A) out of the deep groove ball bearing.

Caution!

In case of non-lubricating bearings, the guard ring (A) must not be removed.

Install the washers (C) possibly removed previously at the same place.

A

16 20

If a central lubrication system is provided, mount lubricating line.

(Fig. 13, 19, 20, 21)

19 C 12

21

298 332.0 - RHB ROLLANT 250 / 250 RC

3.4.7

Pick-up / Rollers Fasten anti-wrapping guard with threaded pin M 12 x 90 on the drive side.

3

Mount flange (3) and/or flange housing (18), lock collar bearing (4) and flange (3) or flange (17) with bolts (6) and contact washers.

1

J 22

Important!

Also mount bracket (H) along with lubricating brush to the top rear bolt of the flange of roller 2.

H

J

Check free wheel mechanism of roller and align if necessary.

1

Arrest lock collar (1) and secure with set screw.

23

If a central lubrication system is provided, mount lubricating line (J).

(Fig. 13, 22, 23) Slide chain wheel (F) on the roller shaft and insert gib head key a little.

Align chain wheel (F) with the next chain wheel (B).

B

Drive in gib head key in this position.

(Fig. 24)

F 24 Mount support (K) and V-belt pulleys if previously removed.

K

A D

Caution!

Insert the orifice plate (D) removed when dismantling into the connection (A) of the hydraulic line (C) from the pressure gauge.

C

Install removed roller chains.

(Fig. 25) 25

3.4.8

RHB ROLLANT 250 / 250 RC - 298 332.0

Pick-up / Rollers Removing roller 11 Remove tailgate K Important!

The lock collar bearings can be replaced without removing the tailgate.

Remove chain wheel (K) on right-hand side.

(Fig. 26) 26 Remove pipe clamp (A) and mounting plate (L).

If a central lubrication system is provided, remove lubricating line (S).

S

Loosen set screw in lock collar (E), drive off and remove lock collar.

A

(Fig. 27)

L E

27 Unscrew hexagon bolts and remove flanges (B) and (C) as well as bearing plate (D).

B

(Fig. 28) D

C

28 Remove wear ring (V) and pull off lock collar bearing (4).

(Fig. 29) V

4

29

298 332.0 - RHB ROLLANT 250 / 250 RC

3.4.9

Pick-up / Rollers Remove lock collar bearing (4) on the left-hand side in the same way.

W11

Remove roller 11 from the tailgate.

Remove anti-wrapping guard from the roller on the right-hand and left-hand side.

4

Clean roller thoroughly from inside with a steam cleaner.

(Fig. 30)

30 Straighten both ends of the roller body. To do this, drive straightening plate (P) (self-manufactured) in up to the stop.

P

Push out the straightening plate with bolts M 16 x 60 if required via two opposed threaded bores.

(Fig. 31)

31

3.4.10

RHB ROLLANT 250 / 250 RC - 298 332.0

Pick-up / Rollers

1

2

3

4

3

5

6 7

8 9 10

3

5

10

9

3

4

7

2

1

6

205263

32 Roller 11, disassembled 1 2 3 4 5 6 7 8 9

Lock collar 50 Set screw M 10 x 8 Sheet-metal flange RB Y 210 Lock collar bearing YEN 210 S Anti-wrapping guard Hexagon bolt M 12 x 40 MK 8.8 A3C Contact washer A 12 Roller 11 Flange * Elbow union Ferrule Threaded stub Stub 10 Flange-housing * * May be lubricated

298 332.0 - RHB ROLLANT 250 / 250 RC

3.4.11

Pick-up / Rollers Installing roller 11 Install anti-wrapping guard (5) in the roller on both sides.

Install roller in the tailgate.

(Fig. 33)

5

33 Slide on inside flange (3) and/or flange housing (10) and lock collar bearing (4).

Place outside flange (3) and/or (9) in position and screw two spacer studs M 12 x 90 into two threaded holes to make installation easier.

3 10

(Fig. 34) 4

34

Important!

If a central lubrication system is provided and a new outside flange (9) is used, screw in lubricating nipple (F) with two serrated lock washers.

D

9

E Using a piece of lubricating line (H) as a guide, insert ferrule (D) and screw in threaded stub (E) hand-tight.

F

(Fig. 35)

H 35

Place wear ring (V) on the flange bearing with grease.

(Fig. 36) V

36

3.4.12

RHB ROLLANT 250 / 250 RC - 298 332.0

Pick-up / Rollers Install bearing plate (D).

Important!

D

When installing, ensure that the wear ring remains on the flanges.

(Fig. 37)

37 Slide on flanges (B) and (C).

(Fig. 38)

B

C

38 Screw in hexagon bolts (6) with contact washers and Loctite 270.

Install bearing on the left-hand side in the same way.

6

Check free wheel mechanism of roller 11 and align if necessary, then tighten all bolts.

Arrest right-hand and left-hand lock collars (1) and secure them.

1

(Fig. 39, 40)

39

6

1

G 40

298 332.0 - RHB ROLLANT 250 / 250 RC

3.4.13

Pick-up / Rollers Connect lubricating line (S) on right-hand side.

Fasten protective conduit (T) with pipe clamp (A) to the bearing plate.

T A

Install mounting plate (L).

S L

Important!

The protective conduit (T) and the lubricating line (S) must be installed behind the mounting plate (L) so there are neither kinks nor chafing.

G

41

Press grease into the lubricating nipple (G) until grease leaks out between bearing plate and tailgate.

(Fig. 40, 41) Slide chain wheel (K) on the left-hand shaft of roller 11 and insert gib head key 14 x 9 x 75 (P) a little.

R

Align chain wheel (K) with jockey sprocket (R).

Drive in gib head key in this position.

Install tailgate.

(Fig. 42) K

P

42

3.4.14

RHB ROLLANT 250 / 250 RC - 298 332.0

Pick-up / Rollers SWINGING SEGMENT Removing the swinging segment Remove roller chain on right-hand side.

A

Remove rear left side panel and panels (A) and (B) from the tailgate.

C

Remove tension springs (C) on right-hand and left-hand side.

B

(Fig. 1)

1 Remove chain wheel (D) from roller 8 and remove washers.

D Important!

Note number of washers for installation.

(Fig. 2)

2 Remove angle plates (E) and (F) from the tailgate on both sides.

E

(Fig. 3)

F

3 Loosen set screw in the lock collar (H) on the left-hand side and drive off lock collar counter clockwise.

If a central lubrication system is provided, remove lubricating line (J) and dismantle clamping bearing (G) of roller 8.

G

(Fig. 4) H J

4

298 332.0 - RHB ROLLANT 250 / 250 RC

3.5.1

Pick-up / Rollers Remove lock collar bearing (L) from roller 8 on right-hand side.

In case of lubricating bearings, remove lubricating line (K) beforehand.

L

(Fig. 5)

K

5

Danger!

Never walk under suspended loads!

Suspend the swinging segment in a suitable lifting device and carefully lift it out of the tailgate.

(Fig. 6)

6 Disassembling the swinging segment Important!

W10

The rollers 8, 9 and 10 have their bearing in the swinging segment; these rollers can only be replaced after disassembling the swinging segment.

W9 W8

(Fig. 7) 7 Remove circlip (S), shim (P) and V-ring (V) from roller 8.

(Fig. 8) V P S

8

3.5.2

RHB ROLLANT 250 / 250 RC - 298 332.0

Pick-up / Rollers Remove guard (A) on right-hand side.

Environment!

Collect leaking semi-fluid lubricant and dispose of properly.

(Fig. 9) A 9 Remove V-ring from spur gear (B), then remove spur gear (B).

S F

E

Pull off spur gears (C), (D), (E) and (F) after unscrewing the bolts, using a puller.

R

Remove deep groove ball bearing from the spur gears (E) and (F) if required.

Remove bolts of tube (R) from the right-hand rocker arm (S).

B

(Fig. 10)

D

C

10 Pull off right-hand rocker arm (S) from the rollers.

Remove washers from the rollers 9 and 10.

S

Remove deep groove ball bearing (G), (H) and (J) from the rocker arm (S) and remove anti-wrapping guards.

(Fig. 11)

G H

J 11 Loosen the set screws, then remove lock collars from rollers 8, 9 and 10.

Remove bolts of tube (R) from the left-hand rocker arm (K) and remove tube.

R

Unscrew bolts of lock collar bearings and pull off left-hand rocker arm (K).

K

(Fig. 12) W10 W9 W8

298 332.0 - RHB ROLLANT 250 / 250 RC

12

3.5.3

Pick-up / Rollers Force the anti-wrapping guard (W) and the lock collar bearing (L) off of the roller, using three bolts.

W

Important!

Clean rollers thoroughly from inside with a steam cleaner.

L

(Fig. 13)

13 Assembling the swinging segment A

Prepare rollers, see section “Removing roller 3”.

A

Place rollers 8, 9 and 10 in correct order and position.

Slide four washers 35 x 55 x 3 (A) on each of the rollers 9 and 10 on the right-hand side.

W10

(Fig. 14) W9 W8

14 Place right-hand rocker arm (S) on the anti-wrapping guard (B) for roller 10, anti-wrapping guard (C) for roller 9 and anti-wrapping guard (D) for roller 8.

(Fig. 15) S B C D 15 Place the bottom sheet-metal flanges (E) and new deep groove ball bearings (F) in position on the other side.

E F

(Fig. 16)

F E

F

16

3.5.4

RHB ROLLANT 250 / 250 RC - 298 332.0

Pick-up / Rollers

G

Place top sheet-metal flanges (H) in position and turn in hexagon bolts M 12 x 35 8.8 (G) with contact washers hand-tight.

G

(Fig. 17)

H H

G

H

17 Place pre-assembled right-hand rocker arm (S) in position at the rollers.

(Fig. 18)

S

18 Drive spur gears (C) and (D) on rollers 9 and 10.

(Fig. 19) C D

19 Slide spur gear (B) on roller 8.

(Fig. 20) B

20

298 332.0 - RHB ROLLANT 250 / 250 RC

3.5.5

Pick-up / Rollers Install corresponding anti-wrapping guard (W) in the roller on the other side.

W

Install seal (Z) with grease into the respective anti-wrapping guard.

Z

(Fig. 21)

21 Place new lock collar bearings (L) in position and drive into the anti-wrapping guard up to the stop.

L

(Fig. 22) L L

22

O

Place left-hand rocker arm (K) in position, turn in and tighten all hexagon bolts M 10 x 28 8.8 (O) with contact washers.

K O

(Fig. 23) O

23 Place tube (R) in position and fasten to the rocker arms with hexagon bolts M 10 x 30 8.8, contact washers and nuts.

R

(Fig. 24)

24

3.5.6

RHB ROLLANT 250 / 250 RC - 298 332.0

Pick-up / Rollers Insert circlip into spur gear (F/E) on one side.

K

Press new deep groove ball bearing (K) to the circlip up to the stop.

N

Insert second circlip (N).

(Fig. 25) F

E

25 Place spur gears (E) and (F) in position and drive on up to the stop.

E F

C

A

A

Important!

When driving on the spur gears, ensure that the teeth engage.

D

B B 26

Turn hexagon bolts M 10 x 25 8.8 (B) with liquid locking compound (DELO-ML 118), washers 11 x 40 x 3 and contact washers into the spur gears (C) and (D) and tighten them.

Turn hexagon bolts M 8 x 20 8.8 (A) with washers 8.5 x 40 x 3 and contact washers into spur gears (E) and (F) and tighten them.

(Fig. 26) Rotate rollers until the bores in the respective spur gear are above the hexagon bolts. Tighten hexagon bolts of the respective deep groove ball bearing.

Important!

The corresponding roller must rotate easily and without chafing (Fig. 27)

27

298 332.0 - RHB ROLLANT 250 / 250 RC

3.5.7

Pick-up / Rollers Slide new V-ring (V) with the dust lip facing the outside on the spur gear of roller 8.

(Fig. 28)

V

28 If required, put new seal (D) on the right-hand guard (A).

Important!

D

The joint must be in the centre of the straight edge.

Fill the guard with approx. 0.8 kg of grease.

(Fig. 29) A 29 Place the guard (A) in position.

Slide guard on the hexagon bolts M 8 x 16, washer 8.5 x 17 x 1 and new seal A 8 x 14.

Turn in hexagon bolts with liquid locking compound (DELO-ML 118) and tighten them.

A

(Fig. 30)

30 Slide new V-ring (V) on the roller stub with the dust lip facing inside.

V

(Fig. 31)

31

3.5.8

RHB ROLLANT 250 / 250 RC - 298 332.0

Pick-up / Rollers Install shim (P) and circlip (S).

(Fig. 32) P S

32 Slide on lock collars (R) on the left-hand side, drive on and secure with set screws.

(Fig. 33) R R R

33 Installing the swinging segment Danger!

Never walk under suspended loads!

Install swinging segment in the tailgate.

(Fig. 34)

34 Mount lock collar bearing (G) with hexagon bolts M 10 x 20 8.8 (K) and contact washers on the left-hand side.

G

K

Slide on lock collar (H), arrest it and secure with set screw.

(Fig. 35)

H

35

298 332.0 - RHB ROLLANT 250 / 250 RC

3.5.9

Pick-up / Rollers On round balers with central lubrication system, connect black lubricating line (J).

(Fig. 36)

J 36 Mount lock collar bearing (Q) with hexagon bolts M 12 x 25 8.8 (T) and contact washers on the right-hand side.

T Q

(Fig. 37)

37 On round balers with central lubrication system, connect blue lubricating line (P).

(Fig. 38)

P 38 Mount bottom angle plates (F) to the tailgate with hexagon bolts M 10 x 20 8.8 (A), contact washers and nuts.

F

(Fig. 39)

A

39

3.5.10

RHB ROLLANT 250 / 250 RC - 298 332.0

Pick-up / Rollers Mount the top angle plates (E) to the tailgate with hexagon bolts M 10 x 20 8.8 (B), contact washers and nuts.

E

(Fig. 40)

B 40 Slide removed shims (H) and chain wheel (D) on the stub of roller 8.

D

(Fig. 41)

H

41 Check alignment of chain wheel (D) with chain wheel (C) (roller 7) and adapt with washers (H) if necessary.

D

Fasten chain wheel (D) with hexagon bolt M 12 x 35 8.8, contact washer and washer 13 x 62 x 6.

(Fig. 42)

C

42 Install panel (G) over the swinging segment to the tailgate.

(Fig. 43)

G

43

298 332.0 - RHB ROLLANT 250 / 250 RC

3.5.11

Pick-up / Rollers Place tension spring (M) at the top on roller of swinging segment tube.

(Fig. 44)

M

44 Hang tension spring (M) into the mounting plate at the bottom.

M

Screw on nut and turn up until dimension (X) has been reached.

X = 79 mm for “soft bales” X = 139 mm for “hard bales” (normal position) Secure nut with lock nut.

X

(Fig. 45)

45 Mount roller chain on right-hand side.

Mount roller guard (C) and side panels (A).

(Fig. 46)

A C 46

3.5.12

RHB ROLLANT 250 / 250 RC - 298 332.0

Pick-up / Rollers REMOVING THE HYDRAULIC BACKWINDER A

Remove cover plate.

B

Screw out nut, then pull out bolt (14) of cylinder (37).

Screw out bolt (13) and remove along the with washer (B) and welded bushing (C).

13

Pull off backwinder (A).

(Fig. 1) C 37

14 1

9

7

Remove bolt (4) and pawl (9).

10

Remove bolt (14) and remove lever (7) from pawl wheel (10) and block (26) from lever. Dismantle leaf spring. Force deep groove ball bearing (8) out of the levers (7).

26

(Fig. 2)

4

8

7

14 2 Remove limit switch (34).

Remove lever (19).

If required, remove bracket (33) and mounting plate (21) from lever (19).

19

Remove guide roller (24) from mounting plate (21).

(Fig. 3)

21

34

33

24 3 Remove hydraulic oil hoses (H) from the cylinder.

Important!

Collect leaking hydraulic oil and dispose of properly.

H

Remove bracket (16).

16

Dismantle cylinder (37) from bracket.

37

(Fig. 4) 4

298 332.0 - RHB ROLLANT 250 / 250 RC

3.6.1

Pick-up / Rollers

1 2 4

3

5

6

8

7

9 10

14

8

15 16

17

17

18

41

7 40

19

11 12

13

20 21 22 23 24 25

30 26

28 27

29 31 32

33 34 35

36

37

36

38

39

205062

Hydraulic backwinder, disassembled 1 Cover plate 2 Hexagon bolt M 8 x 20 8.8 A3C Hexagon nut M 8 Contact washer A 8 3 Hexagon bolt M 12 x 30 8.8 A3C Hexagon nut M 12 Contact washer A 12 4 Hexagon bolt M 8 x 70 8.8 A3C Lock nut VM 8 5 Washer Shear bolt 6 Shim 51 x 71.5 x 1 7 Lever, left-hand 8 Deep groove ball bearing 6012-2RS* C3 9 Pawl 10 Pawl wheel 11 Washer 12 Contact washer A 16 13 Hexagon bolt M 16 x 55 8.8 A3C 14 Hexagon bolt M 10 x 90 8.8 A3C Hexagon nut M 10 Lock nut VM 10 Contact washer A 10 15 Expansion pin 4 x 30 16 Bracket 17 Mushroom head bolt M 10 x 25 8.8 A3C Hexagon nut M 10 Contact washer A 10

3.6.2

18 Hexagon bolt M 10 x 30 8.8 A3C Hexagon nut M 10 Contact washer B 10 19 Lever 20 Lock nut VM 10 21 Mounting plate 22 Hexagon bolt M 12 x 80 10.9 A3C 23 Guide bushing 24 Guide roller 12 x 35 x 15 25 Pin 26 Block 27 Leaf spring 28 Compression spring 29 Contact washer B 6 30 Hexagon bolt M 6 x 25 8.8 A3C 31 Angle plate 32 Lock nut VM 12 33 Bracket 34 Limit switch 35 Hexagon bolt M 6 x 16 8.8 A3C Hexagon nut M 6 Contact washer B 6 36 Washer 37 Hydraulic cylinder 38 Cotter pin 4 x 32 39 Bushing 40 Washer 16.5 x 33 X1 41 Bushing

5

RHB ROLLANT 250 / 250 RC - 298 332.0

Pick-up / Rollers Mounting the hydraulic backwinder Press new deep groove ball bearings (8) into the respective lever (7) up to the stop.

(Fig. 6)

8 7 6 Press both levers (7) on the pawl wheel (10) up to the stop.

10

(Fig. 7)

7

7

7 Mount leaf spring (27) to block (26) with bolts (30), contact washers (29) and compression springs (28).

29

(Fig. 8) 30

28

27

29 26 8 Drive expansion pin (15) into the block.

Place block (26) in position at the lever (7) so that the expansion pin is in the bore.

26

(Fig. 9)

15 7 9

298 332.0 - RHB ROLLANT 250 / 250 RC

3.6.3

Pick-up / Rollers Install pawl (9) between the levers with bolt (4), washer (5) and nut.

(Fig. 10) 5

4

9

10 Push bolt (14) through lever and block, slide on mounting plate (31) and fasten with contact washer and nut.

Slide chain (K) on the bolt (14) and turn on new lock nut (S).

(Fig. 11) K 14 31 S 11 25

Mount guide roller (24) to the mounting plate (21) with bolt (25), guide bushing and nut.

24

Assemble lever (19), mounting plate (21) and bracket (33) with bolts (18), contact washers and nuts (tighten the nuts only hand-tight).

21

(Fig. 12)

18

33 19 12 Mount pre-assembled lever (19) to the side wall with bolts (18), contact washers and nuts.

Mount limit switch (34) (tighten bolts only hand-tight).

(Fig. 13) 19 18

34

3.6.4

13

RHB ROLLANT 250 / 250 RC - 298 332.0

Pick-up / Rollers Mount rear bracket (16) to the side wall with mushroom head bolts (17), contact washers and nuts.

(Fig. 14)

17 17

16 14 Slide cylinder (37) on the pin of the bracket, slide on washer (36) and secure with new cotter pin (38).

(Fig. 15)

38

36

37 15 Slide two shims (6) on the axle journal.

(Fig. 16) 6

16 Slide on pre-assembled backwinder (R).

(Fig. 17)

R

17

298 332.0 - RHB ROLLANT 250 / 250 RC

3.6.5

Pick-up / Rollers Mount welded bushing (C) with contact washer (12), bolt (13) and washer (40).

8

40 Important!

C

Insert as many washers (40) as needed until an air gap of 1 mm is obtained between deep groove ball bearing (8) and welded bushing (C).

12

The space between axle journal and welded bushing must be completely filled.

13 18

(Fig. 18) Insert bushing (39) into the connecting rod of the cylinder.

Mount connecting rod with bolt (22) and new lock nut (32) to the backwinder levers.

(Fig. 19, 20)

39

19

32

22 20

3.6.6

RHB ROLLANT 250 / 250 RC - 298 332.0

Pick-up / Rollers Push connecting rod entirely into the cylinder.

Move the mounting plate (21) with guide roller (24) until dimension (X) 7 ± 1 mm has been reached.

Tighten bolts of mounting plate (21).

21 24

(Fig. 21)

X 21 Connect plug to limit switch (34).

Adjusting the limit switch: A clearance of 2 mm must be provided between angle plate (31) and pressed limit switch (34). Tighten bolts (35).

35

34

(Fig. 22)

31 22 Mount cover plate (1) above the backwinder.

(Fig. 23) 1

23

Replacing the mechanical backwinder Remove guard (T) above the stub.

(Fig. 24)

T 24

298 332.0 - RHB ROLLANT 250 / 250 RC

3.6.7

Pick-up / Rollers Loosen set screw and pull stub (Z) off of the axle journal.

Slide on new stub up to the stop and tighten set screws.

Z

Mount guard.

(Fig. 25)

25

3.6.8

RHB ROLLANT 250 / 250 RC - 298 332.0

4 Twine and net wrapping

Twine and net wrapping TWINE WRAPPING Removing the twine wrapping unit Remove V-belt.

Remove left-hand and right-hand panel (B).

Important!

B

Pay attention to the orifice plate in the pressure relief valve port.

B 5

Remove cover plate (5).

1

(Fig. 1, 25) Only on comfort version machines, pull connector (S) of clutch (K) out of the bar, disconnect connector and pull cable out of the bar with the connector facing upwards.

K 29

21

Remove ropes (28) and (29) from the pin (21).

(Fig. 2, 28)

28

S

2 Disconnect connector (C) from the limit switch (A) of the tying unit.

A

C

Remove pipe clamp (D) and pull out protective conduit to the side.

(Fig. 3)

D

3 On comfort version machines, remove bolt (E) from the mounting plate of clutch (K).

E

(Fig. 4)

K 4

298 332.0 - RHB ROLLANT 250 / 250 RC

4.1.1

Twine and net wrapping On comfort version machines, disconnect connectors (F) and (H) leading to the slot-type switches and remove bracket (21) with mounted rollers (12).

F 21

(Fig. 5, 26, 27)

12 H 5 Suspend twine wrapping unit (G) in lifting device.

Danger!

Never walk and/or work under suspended loads.

Remove right-hand and left-hand bolts, lift out twine wrapping unit and put safely on the ground.

G

(Fig. 6) 6

Removing the cutting unit Remove twine wrapping unit.

3

Unscrew the nut and pull out bolt (3), then remove roller (2).

2

Pull ropes (28) and (29) out of the eyelets to the inside.

29

(Fig. 7, 28)

28 7 Remove cover plate (37) above the cutting unit.

Remove bolts of cutting unit and take out transverse plate (12) with mounted cutting unit.

37

Important!

Remove bracket from the bolts on the right-hand side.

12 (Fig. 8, 28) 8

4.1.2

RHB ROLLANT 250 / 250 RC - 298 332.0

Twine and net wrapping Removing the deflector Unhook tension spring (13).

(Fig. 9, 29)

13

9 Unscrew lock nut from bolt (15) and remove washer and compression spring (14).

Remove bolts (8) and (9) on right-hand side.

14

(Fig. 10, 29)

8 9 15

10 Remove bolts (8) and (9) on the left-hand side.

Remove deflector tube (16) and deflector (4).

(Fig. 11, 29)

16 4

8 9

11 Disassembling the twine wrapping unit Remove yoke (8) from lever.

Remove circlip (12) and pull off cam track (11).

11

8

(Fig. 12, 25)

12

12

298 332.0 - RHB ROLLANT 250 / 250 RC

4.1.3

Twine and net wrapping On standard version machines, remove V-belt pulley, shaft and bushing from the auger transmission if required.

W K

On comfort version machines, remove clutch (K) and shaft (W).

(Fig. 13)

13 Unscrew bolts (7) and remove auger transmission (4).

4

(Fig. 14, 25)

7

14 Unhook hook (17) of tension spring (18) and remove tension spring.

18

(Fig. 15, 27)

17

15 Unscrew nut from bolt (22), pull off compression spring (9) and pull out bolt.

19 22

Remove twine brake (8) and tubing (19).

Unscrew bolts (25) and remove bracket (18).

18

(Fig. 16, 26)

9 25 8

16

4.1.4

RHB ROLLANT 250 / 250 RC - 298 332.0

Twine and net wrapping Unscrew bolts (30) and remove spacer washers.

8

25

Pull off twine tubes (21) and (29). If required, pull off slide tube (16) and remove rod (25) from slide tube.

30 25

Force bushings out of the twine tubes.

Remove yoke (8) of linkage.

(Fig. 17, 27)

16

29 21

16 17

1

Unhook hook (15) and remove tension spring (14).

13 4

14

Release ball receivers of rod (4) and remove from the ball heads.

15

Remove bearing shells (5) and remove angle lever (17).

Unscrew the lubricating nipple (1).

Remove circlip and pull off lever (13).

5

Force out bushings in lever (13) if required.

17

(Fig. 18, 25, 26) 18 Remove circlip, pull out lever (5) and force out bushings (8).

2

5 Important!

Note thickness of possibly fitted supporting rings.

8 Remove guide roller (2) from the lever if required.

(Fig. 19, 25, 27) 19

298 332.0 - RHB ROLLANT 250 / 250 RC

4.1.5

Twine and net wrapping Remove circlip, pull off angle lever (23) and force out bushings.

Remove limit switch (S) if required.

(Fig. 20, 28)

S

23

20

12

Only on comfort version machines, remove rollers (12) from bracket (21) by unscrewing the nuts and pulling out the bolts (13).

12

A

A

Remove slot-type switch (A) if required.

(Fig. 21, 26, 27)

13

21

13 21

Important!

12

If bearing (L) is defective, roller (12) must be replaced.

L

(Fig. 22, 27)

22 Disassembling the cutting unit Unhook hook (14) of tension spring.

Remove twine guides (5) and (6) and knife (8).

14

(Fig. 23, 28)

8 5 23

4.1.6

RHB ROLLANT 250 / 250 RC - 298 332.0

Twine and net wrapping Unhook tension spring (13) from mounting plate (10).

Remove knife (8) and/or (30) and rope (28) and/or (29).

(Fig. 24, 28) 28 29

10

13

8 30 24

298 332.0 - RHB ROLLANT 250 / 250 RC

4.1.7

Twine and net wrapping

2 3 4 5 1

6 7

2 8

3

9 19 19 8

13

10 11 12

18 14

15

16 17

20

205367

25 Twine wrapping unit, disassembled (layout and control): 1 2 3 4 5 6 7 8 9 10 11 12 13

14

15 16

17 18 19 20

4.1.8

Lubricating nipple CS 6 x 1 Hexagon bolt Contact washer A 6 Auger transmission Cover plate Contact washer A 10 Hexagon bolt M 10 x 25 8.8 A3C 8Bushing Bracket Parallel key A 8 x 7 x 32 Cam track Circlip 25 x 1.2 Hexagon bolt M 8 x 20 8.8 A3C Hexagon nut M 10 Contact washer A 10 Mushroom head bolt M 6 x 20 x 15 8.8 A3C Hexagon nut M 6 Contact washer A 6 Flap Hexagon bolt M 8 x 55 8.8 A3C Hexagon nut M 8 Contact washer A 8 Blind rivet A 4.8 x 10 Rail Lubricating nipple AS 6 x 1 Deflector, complete

RHB ROLLANT 250 / 250 RC - 298 332.0

Twine and net wrapping

3

1 2

4

2

1

5

2

9

10

6

7

8

11 12

14

15

13 18 12

19 20 16

5

17

21

24 22

6

23

25

205368

26 Twine wrapping unit, disassembled (twine brake): 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

17 18 19 20

21

Angle joint CS 13 Hexagon nut M 8 Contact washer A 8 Rod Bearing shell Circlip 25 x 1.2 Twine eye Twine brake Compression spring Circlip 15 x 1 Supporting ring S 15 x 21 x 1.5 Bushing Lever Tension spring Hook Hexagon bolt M 8 x 100 8.8 A3C Lock nut VM 8 Contact washer A 8 Angle lever Bracket Tubing Hexagon bolt M 8 x 16 8.8 A3C Lock nut M 8 Contact washer A 8 Bracke

298 332.0 - RHB ROLLANT 250 / 250 RC

22 Hexagon bolt M 6 x 250 x 50 8.8 A3C Lock nut VM 6 Washer 6.4 23 Steel twine eye 24 Contact washer B 8 25 Hexagon bolt M 8 x 16 8.8 A3C

4.1.9

Twine and net wrapping

8

6

11 12

10

31 13

9

7

14

1 2

31

3 4

12

5 9

17

6

18 21 22 23

15

11

16

7

19

8

20 17

24

30

26

24

25

20

20 19 27 32

28

22

20

33

22

23

16 29

23

205369

27 Garnbindung zerlegt (Garnführung): 1 2 3 4 5 6 7 8 9 10 11 12 13

14

15 16 17 18 19 20 21 22

Circlip 12 x 1 Guide roller 12 x 35 x 15 Circlip 15 x 1 Supporting ring S 15 x 21 x 1.5 Lever Pin B 10 A 12 x 28 Cotter pin 4 x 22 Yoke Hexagon nut M 12 Rod Spacer tube Roller Hexagon bolt M 12 x 45 8.8 A3C Lock nut VM 12 Contact washer A 12 Hexagon bolt M 12 x 60 8.8 A3C Lock nut VM 12 Contact washer A 12 Twine threader Slide tube Slide tube Hook Tension spring Lubricating nipple AS 6 x 1 Bushing Twine tube, right-hand Circlip 25 x 1.2

4.1.10

23 24 25 26 27 28 29 30

Steel twine eye Spacer tube Rod Washer 8.5 x 30 x 3 Contact washer A 8 Hexagon bolt M 8 x 20 8.8 A3C Twine tube, left-hand Hexagon bolt M 8 x 20 8.8 A3C Hexagon nut M 8 Contact washer A 8 31 Washer 32 Hexagon bolt M 8 x 20 8.8 A3C Lock nut VM 8 Contact washer A 8 33 Bracket

RHB ROLLANT 250 / 250 RC - 298 332.0

Twine and net wrapping

8

9

11

12

38

7 2 1

4

5

37

6

3

10 38 13 14

7

14 13

15 16

21

10

11

9

17 22 15

7

23 19

22

20

24

26 27

28

25

7 30

29 11 31 32

34 33

36

5

6

35

205370

28 Twine wrapping unit, disassembled (cutting unit): 1 2 3 4 5 6 7 8 9

10 11

12 13 14 15 16

Bracket Roller Hexagon bolt M 8 x 80 8.8 A3C Lock nut VM 8 Twine guide Twine guide Roller Knife left Mushroom head bolt M 8 x 30 8.8 A3C Hexagon nut M 8 Contact washer A 8 Mounting plate Hexagon bolt M 6 x 16 8.8 A3C Hexagon nut M 6 Contact washer B 6 Transverse plate Tension spring Hook Hexagon nut M 6 Hexagon bolt M 6 x 25 8.8 A3C Lock nut VM 6 Washer Stop

17 18 19 Hexagon bolt M 6 x 16 8.8 A3C Hexagon nut M 6 Contact washer B 6

298 332.0 - RHB ROLLANT 250 / 250 RC

20 Mounting clamp 1 x 12-6.2 Limit switch 21 Pin 22 Bushing 23 Angle lever 24 Supporting ring S 15 x 21 x 1.5 25 15 x 1 26 Steel twine eye 27 Circlip 25 x 1.2 28 Rope 29 Rope 30 Knife, right-hand 31 Washer 10.5 32 Spacer tube 33 Roller 34 Spacer tube 35 Bracket 36 Mushroom head bolt M 10 x 45 8.8 A3C Hexagon nut M 10 Contact washer A 10 37 Sheet metal plate 38 Hexagon bolt M 10 x 20 8.8 A3C Hexagon nut M 10 Contact washer A 10

4.1.11

Twine and net wrapping

4

1

5

6

7

3 16

2 15 8

9

5 10

11

12

14

13

8

6

7

9

205371

29 Twine wrapping unit, disassembled (deflector): 1 2 3 4 5 6 7

8 9

10

11 12 13 14 15

16

Hexagon bolt M 8 x 20 8.8 A3C Contact washer B 8 Sheet metal plate Deflector Flap Bar Hexagon bolt M 6 x 20 8.8 A3C Lock nut VM 6 Contact washer A 6 Hexagon bolt M 8 x 20 8.8 A3C Hexagon bolt M 8 x 25 8.8 A3C Lock nut VM 8 Contact washer A 8 Hexagon bolt M 10 x 65 8.8 A3C Hexagon nut M 10 Contact washer A 8 Angle plate Lever Tension spring Compression spring Hexagon bolt M 8 x 55 8.8 A3C Lock nut VM 8 Washer 8.5 x 30 x 5 Deflector tube Deflector tube

4.1.12

RHB ROLLANT 250 / 250 RC - 298 332.0

Twine and net wrapping Assembling the cutting unit 28 29

11

Mount rope (28) and/or (29) to mounting plate (10) with bolt (11), contact washer and nut.

10

11

Mount knife (8) and/or (30) to mounting plate (10) with bolt (11), contact washer and nut.

(Fig. 28, 30)

8 30 30 Place bracket (35) over the bolt (36).

32

33

Place spacer washer (34), spacer tube (32), roller (33) and washer in position.

Screw on nut with contact washer and tighten it.

Important!

12 36 34

The bracket (35) must be parallel to the angled end of the transverse plate (12).

35

31

(Fig. 28, 31) Place bottom twine guide (6) over the bolts (9) and place rollers (7) on the twine guide.

(Fig. 28, 32)

9 7

7

6 32 Place pre-assembled knife (30) and top twine guide (5) in position and fasten with contact washers and nuts.

Important!

5

Mount twine guides and knives in the same way on the other side.

(Fig. 28, 33)

30 33

298 332.0 - RHB ROLLANT 250 / 250 RC

4.1.13

Twine and net wrapping Place rope (29) in the roller (33).

(Fig. 28, 34) 33

29

34 Hang in tension springs (13) and hooks (14).

(Fig. 28, 35) 13

14

13

14

35 Assembling the twine wrapping unit Install new bushings (22) into the angle lever (23).

Slide on angle lever and secure with supporting ring (24) and circlip (25).

25

(Fig. 28, 36)

22

23

36 Press guide roller (2) on the pin of lever (5) and secure with circlip (1).

(Fig. 27, 37) 2

1

5

37

4.1.14

RHB ROLLANT 250 / 250 RC - 298 332.0

Twine and net wrapping Install new bushings (8) into the bracket (9).

Install lever (5) with removed supporting rings (4) and secure with circlip (3).

4

5

(Fig. 25, 27, 38)

8

4 9 38 Force new bushings (12) into lever (13).

Slide on lever and secure with supporting ring (11) and circlip (10).

1

Screw in lubricating nipple (1) and align towards the bore.

12

13

10

(Fig. 25, 26, 39)

11

39 Check length of rod (4), the dimension (X) from the centre of ball receiver to the centre of ball receiver must be 395 mm.

(Fig. 26, 40) 4

X

40

4

14

Mount angle lever (17) to the bracket (9) with bearing shells (5), bolts (16), contact washers and new self-locking nuts.

15

Hang in tension spring (14) and hook (15).

17

Mount rod (4).

5

(Fig. 25, 26, 41) 9 16 41

298 332.0 - RHB ROLLANT 250 / 250 RC

4.1.15

Twine and net wrapping Check length of rod (10), the dimension (Y) from the centre of bore to the centre of bore of the yokes must be 510 mm.

10

(Fig. 27, 42)

Y

42 Install bushings (20) in the twine tubes (21) and (29).

20

20

Mount yoke (8) of rod (10) to the left-hand twine tube (29) with pin (6) and cotter pin.

(Fig. 27, 43)

6 29

8 21

10

43 Slide twine tubes (21) and (29) on the pin of the bracket (9).

21

Important!

Slide on the right-hand twine tube (21) on the side of the auger transmission.

For position of gearing see figure 46..

(Fig. 27, 44, 46)

29 44

Mount rod (25) to the slide tube (16) with bolt (30), spacer tube (24), contact washer and nut if previously removed.

16

Slide slide tubes (16) on the twine tubes.

(Fig. 27, 45)

30

25 45

4.1.16

RHB ROLLANT 250 / 250 RC - 298 332.0

Twine and net wrapping Mount both rods (25) with spacer tube (24), washer (26), contact washer and bolt (28).

26 25

(Fig. 27, 46)

25 26

28

24

46 Mount bracket (18) with bolts (25) and contact washers.

Slide tubing (19) into bracket (18), insert twine brake (8) and slide in bolt (22).

22 8

(Fig. 26, 47) 19 25 18 47 22

Slide compression spring (9) on the bolt (22), place washer in position and screw on new lock nut until dimension (X) 95 mm has been reached (the twine tubes are parallel with the bracket tube).

9

(Fig. 26, 48)

X

48 Hang tension spring (18) into the hook (17) and hang hook into the lever at the twine tube.

(Fig. 27, 49)

18

17 49

298 332.0 - RHB ROLLANT 250 / 250 RC

4.1.17

Twine and net wrapping Hang hook (17) into the tension spring (18) on the other side and hang hook into the bracket tube.

18

(Fig. 27, 50)

17

50 Place auger transmission (4) in position, screw in bolts (7) with contact washers and tighten them.

4 7

Ensure that the parallel key (10) is in place.

(Fig. 25, 51)

10

51 Slide on cam track (11) and secure with circlip (12).

11

12

(Fig. 25, 52)

52

10

8

Fasten yoke (8) of rod (10) to lever (5) with pin (6) and cotter pin (7).

6

(Fig. 27, 53) 7

5

53

4.1.18

RHB ROLLANT 250 / 250 RC - 298 332.0

Twine and net wrapping On standard version machines, insert shaft (C) into the bushing (B) and secure with expansion pins.

Slide bushing (B) over the shaft at the auger transmission (4) and secure with expansion pins.

D

Slide V-belt pulley (D) on shaft (W) and secure with set collar (A).

A

(Fig. 25, 54) 4

B

C

54 On comfort version machines, fasten shaft (W) to the auger transmission with expansion pins.

K

W

Slide on clutch (K) and fasten with hexagon bolt M 10 x 45 8.8 (F), contact washer and washer 11 x 40 x 4 (E).

E F

(Fig. 55)

55

Installing the deflector Insert a bolt (15) into the right-hand outside mounting plate of the deflector tube.

16

Install deflector tube (16) (front part) beneath the drawbar and mount hand-tight with bolts (8), contact washers and self-locking nuts.

L 8 15

Important!

56

Mount the right-hand mounting plate (L) from outside and the left-hand mounting plate from inside to the bracket.

(Fig. 29, 56)

298 332.0 - RHB ROLLANT 250 / 250 RC

4.1.19

Twine and net wrapping If previously removed, mount flap (5) and bar (6) to the deflector (4) with bolts (7), contact washers and self-locking nuts. Install deflector (4) (rear part) beneath the drawbar and mount hand-tight to the deflector tube (16) with bolts (9), contact washers and self-locking nuts.

16

(Fig. 29, 57) 9 4

57 Place lever (12) in position at the deflector tube and introduce bolt (15) into the bore at the same time.

Place compression spring (14) in position and tension to dimension (X) 30 mm with washer 8.5 x 30 x 5 and lock nut.

14

15

(Fig. 29, 58)

X

12

58 Two angled 3 mm sheet metal plates (self-manufactured) are required to adjust the deflector.

110

110

100

(Fig. 59)

90° 59 Insert self-manufactured sheet metal plates (V) on left-hand and right-hand side between roller and deflector.

(Fig. 60)

V

60

4.1.20

RHB ROLLANT 250 / 250 RC - 298 332.0

Twine and net wrapping Place lever (12) on the angle plate (11) and loosen bolt (10).

Press deflector against the inserted sheet metal plates (V) and tighten bolts (8) and (9) on both sides.

8

Tighten bolt (10) and remove inserted sheet metal plates (V).

9

10

(Fig. 29, 60, 61) 12

11

61 Loosen bolts (1) and place lever (12) on the plate (3).

Push plate up until deflector is in its end position.

Tighten bolts (1) in this position.

Hang in tension spring (13).

(Fig. 29, 62) 1 13

3 12

62

Installing the cutting unit Place cutting unit in position and install hexagon bolts M 10 x 20 8.8 (A).

Slide on contact washers on the left-hand side and tighten nuts hand-tight.

A

(Fig. 63)

63 Slide on bracket (1) and contact washers on the right-hand side and tighten nuts hand-tight.

(Fig. 28, 64) 1

64

298 332.0 - RHB ROLLANT 250 / 250 RC

4.1.21

Twine and net wrapping Guide ropes to the outside through the eyes on right-hand side.

29

Important!

Guide the long rope (29) through the top eye and the short rope (28) through the bottom eye.

(Fig. 28, 65)

28 65

Install roller (2) so in bracket that the wire ropes (28) and (29) are between bracket and roller.

3

Install bolt (3) and tighten new lock nut enough to still allow the roller to rotate.

2

Align cutting unit and tighten lateral bolts.

29

(Fig. 28, 66)

28 66 Align cutting unit (12) and tighten lateral bolts.

Install sheet metal plate (37) with bolts (38), contact washers and nuts.

(Fig. 28, 67)

37

12 67

4.1.22

RHB ROLLANT 250 / 250 RC - 298 332.0

Twine and net wrapping Mounting the twine wrapping unit Suspend twine wrapping unit in lifting device and carefully place it in position.

E

Important!

Never walk and/or work under suspended loads!

K 68

On comfort version machines, insert a hexagon bolt M 8 x 50 8.8 (E) with contact washer and nut into the mounting plate of clutch (K), insert it into the bore as a anti-twist protection and tighten nut.

Guide cable (A) from the clutch behind the bar and take connector (B) out of the bottom opening.

A

Connect connectors (B) and (C).

At the bottom, mount one bolt (13) with contact washer and nut on each side.

(Fig. 25, 68, 69) 13 C B 69

A

Guide connector (C) of limit switch (A) of the twine wrapping unit through the opening of the bracket and connect it to the limit switch.

C

Fasten protective conduit with pipe clamp (D) so it will not chafe.

(Fig. 70) D

70 Mount ropes (28) and (29) for twine knife control to the angle lever with pin (21) and nuts and adjust them.

(Fig. 28, 71) 29

21

28 71

298 332.0 - RHB ROLLANT 250 / 250 RC

4.1.23

Twine and net wrapping Adjusting the ropes for twine knife control: Rotate V-belt pulley and/or clutch at the twine wrapping unit manually counterclockwise until it can be heard that the twine knives (8) and/or (30) have fallen down (one cycle, the pull plates (10) lie on the twine guides (5)).

10

In this position, twist the nuts of the ropes at the angle lever until the ropes are slightly tensioned.

5

8 Important!

72

Both ropes must have the same tension.

Turn another cycle and check settings, if necessary correct tension and tighten the rope lock nuts.

(Fig. 28, 72)

On comfort version machines, place rollers (12) in position at the bracket with bolt (13), washer and spacer tube (11) and fasten with contact washer and lock nut.

12 14

Important!

11

12

Mount the roller (12) with two spacer tubes (11) and bolt (14) on the side with the longer, angled end for the slot-type switch.

13 11 73

(Fig. 27, 73)

Mount bracket (21) with mounted rollers with bolts (20), contact washers and nuts.

(Fig. 26, 74) 20

21 74

4.1.24

RHB ROLLANT 250 / 250 RC - 298 332.0

Twine and net wrapping Connect connectors (F) and (H) from the slot-type switches with the connectors of the wiring loom.

(Fig. 75)

F

H 75 Mount cover plate (5) with bolts (2) and contact washers over the twine wrapping unit.

(Fig. 25, 76)

2 5 76 Mount panel (B) on right-hand and left-hand side with hexagon bolts M 8 x 20 8.8 (S), contact washers and nuts.

(Fig. 77)

S

B

77

K

A

Caution!

D Install orifice plate (D) into port (A) of the pressure relief valve before connecting the hydraulic line (C)!

C (Fig. 78)

78

298 332.0 - RHB ROLLANT 250 / 250 RC

4.1.25

Twine and net wrapping NET WRAPPING Removing the net wrapping unit The removal of the net wrapping unit on round baler comfort version machines is described here. Removal on standard version machines is analogously, deviations are pointed out separately.

2

Remove gas struts on the net wrapping unit hood and fold back hood to the rear.

A

Remove right-hand filler plate (2) in the net trough.

Remove bracket (A) with mounted net ramp.

(Fig. 1, 27) 1 Remove V-belt (D).

Unhook tension springs (B) and (C).

Relieve the tension of tension spring (8) and unhook it.

(Fig. 2, 27)

D

8

C B 2 Disconnect connector (E) of electric line from the slot-type switch (only on comfort version machines).

(Fig. 3)

E

3

298 332.0 - RHB ROLLANT 250 / 250 RC

4.2.1

Twine and net wrapping Relieve the tension of knife.

Remove spring-loaded cylinder (21/26) from pin of knife carrier and remove set collar.

(Fig. 4, 30, 31)

21 26

4 Relieve tension of tension springs (22) and (31) of net brake and remove tension springs.

(Fig. 5, 27) 22 31

5 Disconnect plug (G) from motor (24) (only on comfort version machines). Remove protective conduit from cable clamps (H).

24 Important!

G

Another three cable clamps are provided on the net trough.

30

H Remove protective conduit to the right-hand side.

6

Remove baffle plate (30).

(Fig. 6, 28) Remove tube (R) from net trough.

(Fig. 7)

R 7

4.2.2

RHB ROLLANT 250 / 250 RC - 298 332.0

Twine and net wrapping Unscrew the nuts and pull out all fastening bolts (1) on the right-hand and left-hand side.

(Fig. 8)

1

8 Suspend net wrapping unit (N) in lifting device.

N Danger!

Never walk and/or work under suspended loads!

Lift out net wrapping unit and put safely on the ground.

(Fig. 9) 9 If required, remove baffle plate (32) between roller 12 and roller 13. To do this, open and secure tailgate.

(Fig. 10, 28)

32

10 Disassembling the net wrapping unit Remove net trough (3).

(Fig. 11, 27)

3

11

298 332.0 - RHB ROLLANT 250 / 250 RC

4.2.3

Twine and net wrapping Unscrew the nut and pull out bolt (18), then remove spacer bushing (19).

Pull cotter pins out of the net brake (32) on the right-hand and left-hand side.

Pull off mounting plate (30) and angle plate (29) and pull out net brake.

19

32

(Fig. 12, 27)

18

30

29

12 Remove bracket (27) with mounted motor (24) from left-hand side panel (29) (only on comfort version machines).

29

(Fig. 13, 28)

27 24

13 Remove mounting plate (26) (left-hand thread) (only on comfort version machines) and remove lock washer (11) and/or (12) and spacer ring (12) and/or (13).

12 13

(Fig. 14, 30, 31)

11 12 26

14 On standard version machines, pull off stepped gearwheel (3) from outside.

13 14

Remove circlip (13) and/or (14) and force out pin (16) and/or spur gear (17).

16 17

Pull off or force out deep groove ball bearing (14) and/or (15) .

(Fig. 15, 30, 31)

15

4.2.4

RHB ROLLANT 250 / 250 RC - 298 332.0

Twine and net wrapping On comfort version machines, unhook tension spring (F) and remove bracket (H) with mounted jockey pulley (S) from the right-hand side panel.

F

(Fig. 16) H

S 16 On standard version machines, unscrew the nut and pull off jockey pulley (A) from the hexagon bolt.

(Fig. 17)

A

17 Unscrew nut from bolt (14).

Unscrew bolts (6) and pull off brake lever (7).

Important!

6

14

The bolts (6) have been installed with liquid locking compound and are therefore tightly seated.

7 (Fig. 18, 27) 18 Unscrew nut from bolt (14) on the other side and pull out brake shafts with mounted bracket (21).

(Fig. 19, 27)

14

21

19

298 332.0 - RHB ROLLANT 250 / 250 RC

4.2.5

Twine and net wrapping Remove bracket (26) with mounted slot-type switch (25) (only on comfort version machines).

25

Remove V-belt pulley (K) with free wheel mechanism from the rubber-coated roller.

26

Force free wheel mechanism out of the V-belt pulley if required.

R

Loosen set screw in set collar (R) and pull off set collar (only on comfort version machines).

K

(Fig. 20, 29) 20 Remove cover plate (11) from the angle plates.

(Fig. 21, 28)

11

21 Remove bolt (4) from the pressure roller (10) and bolts (13) from the stripper loop (21) on both sides.

6

Remove pressure roller with stripper loop and angle plate (6).

10

Remove circlip from the shaft if required and take shaft and deep groove ball bearing out of the pressure roller.

4

(Fig. 22, 28) 13

21 13 22 Pull cotter pins (14) out of the tensioning lever.

Unscrew bolts (5), remove circlips (7) and remove side panels.

14

5

(Fig. 23, 28, 29)

7

23

4.2.6

RHB ROLLANT 250 / 250 RC - 298 332.0

Twine and net wrapping Pull off hook (23) from knife carrier (5).

Danger!

The knife on the knife carrier is very sharp.

(Fig. 24, 29) 5 23

24 Pull plastic bushing (12) out of the knife carrier (5) on right-hand and left-hand side and lift out roller (6).

6

Remove knife (21) from knife carrier.

5

(Fig. 25, 29)

12

21 25 On standard version machines, remove spur gear from roller (6).

6

11

If required, remove circlip (8), pull off bearing (11), take out circlip (9) and force out deep groove ball bearing (10).

10

(Fig. 26, 29)

9 8 26

298 332.0 - RHB ROLLANT 250 / 250 RC

4.2.7

Twine and net wrapping

37 4 38

5 2 1

3

1

7

8

6

9 10

4

17

35 16

17 16

16

13 14

11 12

15 34 18

33

5

4 10 36

20

19 14 13 21 28 29

1

32

6

22

27 23 24 25 26

4

30 27

31

20 10

28 205298

27 Net wrapping unit, disassembled (net roll brake): 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18

19 20 21 22 23

Wing nut M 8 Filler plate, right-hand Trough Contact washer A 10 Hexagon bolt M 10 x 16 8.8 A3C Hexagon bolt M 10 x 25 8.8 A3C Brake lever Tension spring Eyebolt Hexagon nut M 10 Cotter pin M 5 x 36 Washer Bushing Mushroom head bolt M 10 x 40 8.8 A3C Filler plate, left-hand Short brake shaft D 22 x 1300 Long brake shaft D 22 x 1335 Hexagon bolt M 10 x 80 8.8 A3C Lock nut VM 10 Washer Spacer bushing Eyebolt Bracket Tension spring Hexagon bolt M 8 x 25 8.8 A3C Hexagon nut M 8 Lock nut VM 8

4.2.8

24 Catch hook 25 Tension spring 26 Hexagon bolt M 6 x 20 8.8 A3C Lock nut VM 6 27 Cotter pin 3.2 x 22 28 Washer 29 Angle plate 30 Mounting plate 31 Tension spring 32 Net brake 33 Hexagon bolt M 8 x 20 8.8 A3C Hexagon nut M 8 Contact washer A 8 34 Hexagon nut M 8 35 Rollatex net 36 Contact washer B 10 37 Hexagon bolt M 10 x 25 8.8 A3C Hexagon nut M 10 Contact washer A 10 38 Stop

RHB ROLLANT 250 / 250 RC - 298 332.0

Twine and net wrapping

9 4

1 2

11

10

5 6 7

3

8

13 12

16

14 15

17 18

19 20

13 21

24

22 25

23

26 27

29 1

28 33

8 7

12

4

6 5

14 19

30

34

13 12 23 31 32 22

205299

28 Net wrapping unit, disassembled (layout and pressure roller): 1 Hexagon bolt M 8 x 20 8.8 A3C Hexagon nut M 8 Contact washer A 8 2 Side panel, right-hand 3 Bracket 4 Hexagon bolt M 10 x 16 8.8 A3C 5 Contact washer B 10 6 Angle plate 7 Circlip 20 x 1.2 8 Deep groove ball bearing 6204-2RS 9 Shaft D 20 x 1300 10 Pressure roller 11 Cover plate 12 Contact washer B 8 13 Hexagon bolt M 8 x 16 8.8 A3C 14 Cotter pin 15 Tensioning lever 16 Hook bolt 17 Expansion pin 3.5 x 24-N 18 Compression spring 19 Washer 10.5 20 Hexagon nut M 10 21 Stripper loop 22 Hexagon bolt M 10 x 16 8.8 A3C 23 Contact washer A 10

298 332.0 - RHB ROLLANT 250 / 250 RC

24 Wiper motor* Hexagon nut* BM 14 x 1 Washer* 25 Catch* 26 Mounting plate* 27 Bracket* 28 Washer* 5.3 Spring washer* 5 Hexagon nut* M 5 29 Side panel, left-hand 30 Baffle plate 31 Hexagon bolt M 8 x 20 8.8 A3C Hexagon nut M 8 Contact washer A 8 32 Baffle plate 33 Washer 34 Hexagon bolt M 8 x 20 8.8 A3C Hexagon nut M 8 Contact washer A 8 * only on comfort version machines

4.2.9

Twine and net wrapping 10 7

9

11 9

12

8 5

6 12 11 9 10

25 28

8

26 9

27

18

4

2

1

3

15

13 7

14

24

19 20 21

22

17

16 23

205300

29 Net brake unit, disassembled (roller and knife): 1 Guide roller 12 x 35 x 15 2 Hexagon bolt M 12 x 35 8.8 A3C Hexagon nut M 12 Contact washer A 12 Washer 13 3 Stop 4 Countersunk head bolt M 8 x 30 8.8 A3C Hexagon nut M 8 Contact washer A 8 5 Knife carrier 6 Roller 7 Circlip 65 x 2.5 8 Circlip 25 x 1.2 9 Circlip 52 x 2 10 Deep groove ball bearing 6205-2RS 11 Bearing 12 Plastic bushing 13 Spur gear** 14 Detent edged ring** VSKZ 10 15 Hexagon bolt** M 10 x 35 A3C 16 Mushroom head bolt M 8 x 25 8.8 A3C Hexagon nut M 8 Contact washer B 8 17 Stop 18 Washer 16.5 x 33 x 1 19 Contact washer A 6 20 Hexagon bolt M 6 x 12 8.8 A3C

4.2.10

21 22 23 24 25 26 27

Knife Angle plate Hook Talcum powder Slot-type switch* Bracket* Cheese-head screw* M 5 x 20 Hexagon nut* M 5 Serrated lock washer* A 5,3 28 Hexagon bolt* M 6 x 16 8.8 A3C Hexagon nut* M 6 Contact washer* A 6 * only on comfort version machines ** only on standard version machines

RHB ROLLANT 250 / 250 RC - 298 332.0

Twine and net wrapping

9

3

2

1

4

5

7

10

8

11

6

9

10 19

20 18

14

12 13

16

11

22 10

17 15

15

9

21

23

18

11 24

7 25

26

205301

30 Net wrapping unit, disassembled (knife pre-stressing – standard version): 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

Hexagon bolt* M 8 x 12 Pin* Stepped gearwheel* Washer* 16 x 24 x 3 Spring clip* Cotter pin* 3.2 x 28 Cotter pin 5 x 32 Washer Expansion pin 3 x 30-N Expansion pin 5 x 30-N Set collar Lock washer 8 Spacer ring Circlip 12 x 1 Deep groove ball bearing 6201-2RS Circlip 32 x 1.5 Spur gear*

18 19 20 21 22 23 24 25 26

Stop washer Rod Compression spring Circlip 40 x 1.75 Pin Cheese-head screw M 10 x 30 Hexagon nut M 10 Washer Spring-loaded cylinder

* only on standard version machines

298 332.0 - RHB ROLLANT 250 / 250 RC

4.2.11

Twine and net wrapping

3 1

4 5

2

3

4

6

7

8

11

3

10

16

15

13 12

4

5 9

14

14

17

18

1

5 19

20

21

205302

31 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

Cotter pin 5 x 32 Washer Expansion pin 3 x 30-N Expansion pin 5 x 30-N Set collar Rod Compression spring Stop washer Circlip 40 x 1.75 Pin Lock washer 8 Spacer ring Circlip 12 x 1 Deep groove ball bearing 6201-2RS Circlip 32 x 1.5 Pin* Stop washer Cheese-head screw M 10 x 30 Hexagon nut M 10 Washer Spring-loaded cylinder

* only on comfort version machines

4.2.12

RHB ROLLANT 250 / 250 RC - 298 332.0

Twine and net wrapping Assembling the net wrapping unit Mount angle plate (22) and knife (21) to the knife carrier (5) with bolts (20) and contact washers.

22

5

(Fig. 29, 32)

21

20

32 Install circlip (9) in the bearing (11) on one side, force in deep groove ball bearing (10) and install second circlip (9).

6

11

Force bearing (11) with installed deep groove ball bearing (10) on roller 6 and secure with circlip (8).

10

On standard version machines, slide on spur gear (13) and secure with bolt (15) and contact washer.

(Fig. 29, 33)

9 8 33

Install roller (6) in knife carrier (5) and slide plastic bushing over the bearing and install it in the knife carrier.

6

(Fig. 29, 34) 5 12

34 Slide washer (18), hook (23) and washer (18) on the knife carrier.

23

(Fig. 29, 35)

18

18 35

298 332.0 - RHB ROLLANT 250 / 250 RC

4.2.13

Twine and net wrapping Install pre-assembled roller in a side panel and insert circlip (7) into the bearing groove.

7

Important!

The entire circumference of the circlip must be placed inside the groove.

(Fig. 29, 36)

36 Install tensioning lever (15) and secure with washer and cotter pin (14).

15 16

Place brake shafts (16) in position and fasten to the side panel with contact washers and bolts (5).

14

(Fig. 27, 28, 37) 5

37 If previously removed, mount bracket (21) to the brake shafts (17) with contact washers and bolts (6), using liquid locking compound (DELO-ML 118).

17

Install mushroom head bolt (14) in the side panel and slide on bushing (13).

6

Slide in brake shafts (17) and slide contact washer on mushroom head bolt, then screw on nut.

17

Place side panel in position on the other side and secure tensioning lever with washer and cotter pin.

13

21 38

Fasten brake shafts (16) with contact washers and bolts (6).

(Fig. 27, 28, 38)

4.2.14

RHB ROLLANT 250 / 250 RC - 298 332.0

Twine and net wrapping Install mushroom head bolt (14) and slide on bushing (13).

14 17

Place brake lever (7) in position at the brake shafts (17).

13

Screw in bolts (6) with contact washers and liquid locking compound (DELO-ML 118) and tighten on both sides.

(Fig. 27, 39) 7 39 Install shaft (9) and deep groove ball bearing (8) in the pressure roller (10) and secure with circlip (7).

9

(Fig. 28, 40) 8

7 10 40 Slide angle plate (6) on the pressure roller (10) and the stripper loop (21) on the right-hand and left-hand side and install between the side panels.

21

(Fig. 28, 41)

10 6 41 Screw bolt (4) into the pressure roller with contact washers on the right-hand and left-hand side and tighten it.

4

Screw in bolts (13) with contact washers and tighten them.

(Fig. 28, 42)

13 13 42

298 332.0 - RHB ROLLANT 250 / 250 RC

4.2.15

Twine and net wrapping Mount cover plate (11) to the angle plates with hexagon bolts M 8 x 20 8.8, contact washers and nuts.

(Fig. 28, 43) 11

43 Slide on set collar (R) up to dimension (X) 38 mm and secure with set screw.

Important!

Mount set collar only on comfort version machines.

X R

(Fig. 44)

44 Force free wheel mechanism (F) into V-belt pulley (K) so it is flush.

K

(Fig. 45)

F

45 Slide V-belt pulley (K) with free wheel mechanism so on the pressure roller shaft that the free wheel mechanism rotates clockwise.

K

Screw in hexagon bolt M 10 x 30 8.8 (B) with contact washer and washer 25 x 11 x 6 (A) and tighten it (hold pressure roller tight while tightening).

A

(Fig. 46)

B

46

4.2.16

RHB ROLLANT 250 / 250 RC - 298 332.0

Twine and net wrapping Install bracket (26) with mounted slot-type switch (25), using bolts (28).

26

Fasten cable of slot-type switch to the side panel with clamp (K).

28 25

(Fig. 29, 47)

K

47 Place stop (A) in position on the right-hand side panel from inside with hexagon bolt M 10 x 65 8.8 (S).

A S

Important!

On standard version machines, fasten stop to the side panel with hexagon bolt M 10 x 25 8.8, contact washer and nut.

(Fig. 48) 48

B

Slide on bushing (B), flange sleeve (C), bracket (D) with mounted jockey pulley and washer 10.5 x 40 x 5 (E) from outside.

C

Screw on nut and tighten it.

D E

(Fig. 49)

49

L

If previously removed, insert hexagon bolt M 8 x 70 8.8 (L) with washer 8.5 x 30 x 5 from inside, slide on washer 8.5 x 30 x 5 (G) and tighten with nut (H).

G H F

J

Slide on tension spring (F) and screw on lock nut (J).

Hang hook (M) into tension spring and bracket.

M

(Fig. 50)

50

298 332.0 - RHB ROLLANT 250 / 250 RC

4.2.17

Twine and net wrapping

Important!

R

N

On standard version machines, insert hexagon bolt M 12 x 110 8.8 (N) and slide on washer 13 x 40 x 6 (T) and tube (R).

P

T

Slide on jockey pulley (P) and fasten with washer and new lock nut.

(Fig. 51) 51 Install circlip (15) and/or (16) into the inside groove of the left-hand side panel.

15 16

(Fig. 30, 31, 52)

52 Push in deep groove ball bearing (14) and/or (15) from inside up to the stop at the circlip.

Slide second deep groove ball bearing on the pin or, on standard version machines, on the spur gear.

14 15

Install pin and/or spur gear in the deep groove ball bearing from outside.

(Fig. 30, 31, 53, 54)

53 Install circlip (13) and/or (14) into the groove of pin (16) or of spur gear (17).

13 14

(Fig. 30, 31, 54) 16 17

54

4.2.18

RHB ROLLANT 250 / 250 RC - 298 332.0

Twine and net wrapping Slide on spacer ring (12) and/or (13) and insert lock washer (11) and/or (12).

12 13

Only on comfort version machines, screw on catch (25).

11 12

(Fig. 30, 31, 55)

26

55 Install bracket (27) with mounted motor (24) to the side panel, using bolts (34).

24 Important!

Also install washers (33) between side panel and bracket.

25

27

The pegs on the catch (25) must be in the bores of the mounting plate (26).

26 33

34 56

(Fig. 28, 56) Slide net brake (32) into the net trough and fasten with washers (12) and cotter pins (11) on the right-hand side.

(Fig. 27, 57)

11 11

12

12

32

57 On the other side, install mounting plate (30) and bracket (29) with washers and cotter pins to the net brake.

Fasten mounting plate (30) with screw (18), distance bushing (19), contact washer and now lock nut to the net trough.

19

32

(Fig. 27, 58)

29

30

18 58

298 332.0 - RHB ROLLANT 250 / 250 RC

4.2.19

Twine and net wrapping Mount net trough (3) to the net wrapping unit with bolts (33), contact washers and nuts.

(Fig. 27, 59)

33 3 59

Mounting the net wrapping unit Suspend the net wrapping unit in lifting device and place it on the housing.

Danger!

Never walk or work under suspended loads.

31 30

Place baffle plate (30) in position and insert bolts (1) and (31).

60

On the front right-hand bolts, mount bracket (H) as well.

Slide on contact washers, screw on nuts and tighten them.

1

Move head of bolt M 8 x 55 (A) up to the stop at the side wall and tighten lock nut.

Hang in tension spring (Z) with hook.

H

A

(Fig. 28, 60, 61)

Z 61 Connect connectors (E) of the electrical line from the slot-type switch (only on comfort version machines).

(Fig. 62)

E

62

4.2.20

RHB ROLLANT 250 / 250 RC - 298 332.0

Twine and net wrapping Hang in tension spring (8) for net brake at the brake lever (7).

(Fig. 27, 63)

8

7

63 Insert eyebolt (9) into the bracket (3) and hang into tension spring (8).

Adjust the eyebolt so that the dimension (X) from bracket up to the end of the eyebolt is approx. 70 mm.

3 9

Tighten lock nut.

X

Fasten cable (K) to the eyebolt so it will not chafe.

(Fig. 27, 28, 64) 8 K 64 Install V-belt.

On standard version machines with twine and net wrapping, hang tension spring (Z) into the bracket of the jockey pulleys. Hang hook (H) into the tension spring and in the rear bracket.

(Fig. 65)

H Z

65 Install bracket (B) with mounted net ramp at the top with hexagon bolts M 8 x 20 8.8 and at the bottom with hexagon bolts M 8 x 60 8.8, contact washers and nuts.

2

Install right-hand filler plate (2).

(Fig. 27, 66)

B

66

298 332.0 - RHB ROLLANT 250 / 250 RC

4.2.21

Twine and net wrapping Only on comfort version machines lay cable to the left so it will not chafe as shown in the figure and press into the cable clamps on the net trough.

(Fig. 67)

67 Mount tube (R) to the net trough with hexagon bolt M 8 x 25 8.8, contact washer and nut.

(Fig. 68)

R 68 Only on comfort version machines, push protective conduit into the cable clamp (H) and connect plug (G) to motor (24).

(Fig. 28, 69)

24 G

H

69 Mount eyebolts (20) to the brackets and hang in tension springs (22) and (31).

20 22

Tension tension spring (31) for net roll tensioning clamp so that dimension (X) is 345 mm. Tension tension spring (22) so that dimension (Y) is 250 mm.

Y

(Fig. 27, 70) X

20 31

70

4.2.22

RHB ROLLANT 250 / 250 RC - 298 332.0

Twine and net wrapping Slide set collar (5) and/or (11) on the stub of the knife carrier.

(Fig. 30, 31, 71) 5 11

71 Slide on spring-loaded cylinder (21) and/or (26) of net cutter tensioning device and secure with washer and cotter pin.

(Fig. 30, 31, 72)

21 26

72

Danger!

Danger from pinch points!

☞ Whenever working on the open tailgate H

and in der bale chamber, set the levers (H) of the tailgate safety lock to end position (Z).

O Z

Before closing the tailgate, set lever (H) to end position (O).

73

(Fig. 73) Check if hook (23) falls behind the spacer ring (12) with an overstroke of 5 mm min. and adjust if necessary.

23

(Fig. 29, 31, 74)

12

74

298 332.0 - RHB ROLLANT 250 / 250 RC

4.2.23

Twine and net wrapping

Important!

23

Figure 75 shows the hook (23) on standard version machines.

(Fig. 29, 75)

75 To adjust, loosen lock nut (19) and/or (24) on the spring-loaded cylinder (21) and/or (26) and turn adjusting bolt (18) and/or (23) correspondingly.

Tighten lock nut.

21

Important!

Figure 77 shows the standard version.

19

18

(Fig. 30, 31, 76, 77) 76

24

26

23

77 Check setting of compression springs (18) for pressure roller. To do this, place tensioning arms (16) on tensioning arm (15), but do not tension.

16

18

The spring length (X) must be 60 mm, adjust if necessary by turning the nuts.

(Fig. 28, 78)

15 16

X 18

4.2.24

78

RHB ROLLANT 250 / 250 RC - 298 332.0

Twine and net wrapping If previously removed, insert baffle plate (32) between the 12th and 13th roller from the inside, with the double-bent side facing forward.

(Fig. 28, 79)

32

79 Screw bolts (22) into the baffle plate from outside with contact washers and tighten them.

(Fig. 28, 80) 22

80 Mount gas struts (G) of the hood to the mounting plates of the side panels on both sides with hexagon bolts M 8 x 25 8.8.

G

Important!

Mount the gas strut to the mounting plate from outside.

(Fig. 81) 81

298 332.0 - RHB ROLLANT 250 / 250 RC

4.2.25

5 Machine housing

Machine housing TAILGATE Removing the tailgate Remove right-hand roller chain.

Remove “Roller drive front” roller chain.

Relieve the tension of tension spring (M) of swinging segment on both sides and remove it.

(Fig. 1)

M

1 Remove hydraulic cylinder (Z) on the right and left from the pins of the tailgate.

Important!

Do not remove the hydraulic hoses!

Z (Fig. 2)

2 In case of net wrapping, relieve tension of net wrapping knife.

Caution!

F When failing to relieve the tension of knives, the spring-loaded cylinder is under tension.

Remove spring-loaded cylinder (F) of knife pre-tensioning.

3

(Fig. 3) Remove protective hose (A) out of the cable clamps on right-hand side.

A

Disconnect plug (S) from bale ejector limit switch (G).

S

(Fig. 4) G

4

298 332.0 - RHB ROLLANT 250 / 250 RC

5.1.1

Machine housing Pull plug (C) out of the brace (B) to the bottom and disconnect it.

B

Pull plug housing out of the brace to the top.

(Fig. 5)

C

5 Remove left-hand side cover and bracket (D).

Pull out gib head key (N) and pull off chain wheel (K).

(Fig. 6) N D

K 6 Suspend tailgate in lifting device.

If a central lubrication system is fitted, remove lubricating line (E) on the left-hand side.

Unscrew the nuts the pull out the bolts (H) on the right-hand and left-hand side.

E

Danger!

Never walk and/or work under suspended loads.

H

7 Lift off tailgate and put safely on the ground.

(Fig. 7, 8)

H

8

5.1.2

RHB ROLLANT 250 / 250 RC - 298 332.0

Machine housing Mounting the tailgate Danger!

Never walk and/or work under suspended loads.

Suspend tailgate in lifting device and place in position at the chassis.

(Fig. 9) 9 Insert hexagon bolts M 12 x 100 8.8 (H) on the right-hand and left-hand side and fasten with contact washers and new self-locking nuts.

T E

Important!

Also fasten mounting plate (T) to the top bolt on the left-hand side.

H

If a central lubrication system is provided, install lubricating line (E).

10

(Fig. 10)

Slide on chain wheel (K) and insert gib head key 14 x 9 x 75 a little.

Align chain wheel with double chain wheel of roller 13 and drive in gib head key in this position.

(Fig. 11) N

K 11

298 332.0 - RHB ROLLANT 250 / 250 RC

5.1.3

Machine housing Guide plug housing (R) downward behind the brace (B).

Connect plug and place in the brace.

(Fig. 12) B R

12 Connect plug (S) to the bale ejector limit switch (G).

A

Lay protective hose (A) so it will not chafe and install it in the cable clamps (M).

S

(Fig. 13, 14) G

13

M

M A 14 Slide tailgate cylinder (Z) on the pin on the right-hand and left-hand side and secure with washer (D) and expansion pin (T).

(Fig. 15) Z D T

15

5.1.4

RHB ROLLANT 250 / 250 RC - 298 332.0

Machine housing Slide set collar (L) on the stub (P) of knife carrier.

(Fig. 16)

P

L

16 Slide on spring-loaded cylinder (F) of net cutter tensioning device and secure with washer and cotter pin.

(Fig. 17)

F 17 Insert pin (E) into bracket on the tailgate on the other side of the spring-loaded cylinder and secure with washer and cotter pin.

D

Install bracket (D) for left-hand side door.

(Fig. 18) E

18 Install roller chains.

M

Hang in tension springs (M) of swinging segment and turn up nut until dimension (X) has been reached.

X = 79 mm for “soft bales” X = 139 mm for “hard bales”(normal position) Secure nut with lock nut.

(Fig. 19)

X

19

298 332.0 - RHB ROLLANT 250 / 250 RC

5.1.5

Machine housing Adjustment Open tailgate halfway.

Adjust stop bolt (C) so that the tailgate sensor (S) is pushed in 5 mm.

S

(Fig. 20) C

20 Hold a square tube (V) (! 30 mm) against the frame at the centre point of roller 2 (W).

Carefully close tailgate (up to the stop at the square tube).

(Fig. 21) W

V 21 In this position, the lever (B) must make contact with the stop bolt (C). If necessary loosen lock nuts of stop bolt (D), adjust stop bolt correspondingly and tighten lock nuts.

Open tailgate slightly, remove square tube and close tailgate.

B C

(Fig. 22)

D

22

5.1.6

RHB ROLLANT 250 / 250 RC - 298 332.0

6 Hydraulic system – Electric system

Hydraulic system – Electric system VALVE COMBINATION Checking the tightness of tailgate valve combination and hydraulic cylinder The following items are required for this check:

C

N

Hand pump (P), ball valves (C) and (E), L-type union (M), union (N) and hose (F).

(Fig. 1, 3)

N

M E

Close tailgate if open.

Mount union (N) to the ball valve (C) at the L-type union of the valve combination.

F 1

Environment!

A

C

Collect leaking hydraulic oil and dispose of properly!

B Connect hydraulic hose (F) from ball valve (E) to the L-type union (K).

D

Connect hydraulic hose (D) from a hand pump to the tee (between the ball valves).

E

Remove hydraulic line (B) to the pressure gauge at the L-type union and plug port with a plug (A).

F

K

2

Important!

Pay attention to the orifice plate in the port!

G

Open both ball valves.

To remove any air contained in the system, open and close tailgate.

P

Checking the cylinders: H

Important!

Perform check only when hydraulic oil is cold 3 Close ball valve (C) and open ball valve (E).

Apply a pressure of 230 bar (G) to the cylinders, using the hand pump (P); this pressure may fall by 5 bar max. within 30 seconds.

No oil may leak from the cylinders.

If oil leaks out, replace seals in the cylinder.

When finished, release the pressure with the handwheel (H).

298 332.0 - RHB ROLLANT 250 / 250 RC

6.1.1

Hydraulic system – Electric system Checking the valve combination Important!

Perform check only when hydraulic oil is cold!

Close ball valve (E) and open ball valve (C).

Apply a pressure of 230 bar to the valve combination, using the hand pump.

The pressure may fall by 10 bar max. within 30 seconds, if necessary replace valve combination.

When finished, release the pressure with the handwheel (H).

Remove ball valves (C) and (E) and plug (A).

Re-fit hydraulic line to the L-type union of valve combination and to L-type union (K).

Important!

Pay attention to the orifice plate in the L-type union on the valve combination.

(Fig. 2, 3)

Removing the valve combination Ü

Clean surroundings of valve combination.

Remove union nuts (Ü) of hydraulic lines, plug ports with plugs.

S Environment!

1

Collect leaking hydraulic oil and dispose of properly! Ü 4

Unscrew nuts and pull out bolts M 8 x 50 8.8 (S), then remove valve combination (1).

(Fig. 4, 6)

6.1.2

RHB ROLLANT 250 / 250 RC - 298 332.0

Hydraulic system – Electric system Disassembling the valve combination Unscrew pressure relief valve (6) and remove compression spring and valve needle.

6

Important!

The valve body (11) has been screwed in with liquid locking compound and can only be removed with a special tool.

22 16 5

Unscrew screw plug (22) and remove spring guide, compression spring and non-return valve.

Unscrew valve cartridge (16) and remove piston.

(Fig. 5, 6)

298 332.0 - RHB ROLLANT 250 / 250 RC

6.1.3

Hydraulic system – Electric system

12 15

13

2 4

5

6

7

8

9

13

20

10 3

19

11

21

22

1

17 18 16 13 14

205416

6 Valve combination, disassembled 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22

6.1.4

Valve combination Cap Hexagon nut M 10 Twist grip O-ring 19 x 3.5 -N Cap Piston O-ring 12.37 x 2.62-N Compression spring Valve needle Valve body Male connector L 10F-M O-ring Male connector L 8F-M14 x 1.5 Piston Valve cartridge O-ring 13.94 x 2.62-N O-ring 19.3 x 2.2 -N Non-return valve Compression spring Spring guide Screw plug VSTI M14 x 1.5-OR

RHB ROLLANT 250 / 250 RC - 298 332.0

Hydraulic system – Electric system Assembling the valve combination Important!

15

17

18

Ensure absolute cleanliness during assembly.

19 20

21 Insert piston (15).

Install new O-rings (17) and (18) on valve cartridge (16) and screw in valve cartridge.

16 13

22 7

Insert non-return valve (19), compression spring (20) and spring guide (21).

Screw in screw plug (22) with new O-ring (13) and tighten it.

(Fig. 6, 7)

Loosen lock nut of piston (7) in twist grip (4) and fully screw on twist grip.

Insert valve needle (10) and compression spring (9).

Screw in pressure relief valve (6) and tighten it.

10 6

4

Connect port “A1” of valve combination (1) to a nozzle tester (P).

9

Fill tank with clean hydraulic oil.

Build up pressure with the hand lever.

8

At 230 bar, hydraulic oil must leak from the ports “B1” and “B”.

If hydraulic oil leaks before that point or later, loosen lock nut on piston (7) and turn piston correspondingly.

Now tighten lock nut and secure with safety paint.

P

Remove valve combination (1) from tester.

(Fig. 6, 8, 9)

7 1 7 9

298 332.0 - RHB ROLLANT 250 / 250 RC

6.1.5

Hydraulic system – Electric system Removing the 4/3-way valve with circulation shut-off valve Clean surroundings of 4/3-way valve.

S S

Remove all angle plugs (W) from the solenoid valves.

Unscrew union nuts (Ü) of hydraulic lines from their ports and plug ports with plugs.

Ü

A Environment!

Collect leaking hydraulic oil and dispose of properly!

W 10

Unscrew the nuts and pull out bolts (S) and remove 4/3-way valve (A).

(Fig. 10)

Disassembling the 4/3-way valve with circulation shut-off valve

V

Unscrew bolts and remove 4/3-way valve (A) from circulation shut-off valve (V).

(Fig. 11)

A 11 Unscrew union nuts (B) and pull solenoids (C) off of the coil cores.

B

C

A

C

Turn out the coil cores and remove compression spring, spring guides and spool out of the 4/3-way valve (A).

B

(Fig. 12)

12

6.1.6

RHB ROLLANT 250 / 250 RC - 298 332.0

Hydraulic system – Electric system Unscrew union nut (D) and pull off solenoid (E) from the coil core.

V

Unscrew coil core and remove compression spring and spool from the circulation shut-off valve (V).

(Fig. 13)

D

E

13

Assembling the 4/3-way valve with circulation shut-off valve Important!

Ensure absolute cleanliness during assembly.

F G

Insert compression spring (F) and spool (G) into the circulation shut-off valve (V).

V

(Fig. 14) 14 Screw in coil core (H) with new O-ring and tighten it.

Slide solenoid (E) over the coil core, slide on new O-ring (I) and screw on union nut (D) (tighten only after mounting the angle plugs).

(Fig. 13, 15)

I

E H

15 Insert spool (O) so into the 4/3-way valve (A) that the side with the circular groove faces the port side “B”.

Insert spring guides (N) and compression springs (M).

A

Screw in coil cores (K) with new O-rings (L) and tighten them.

Important!

K

L

N M

O

L

N

Coil core 0003 on port side “B” and 0002 on port side “A”.

K

M 16

(Fig. 16)

298 332.0 - RHB ROLLANT 250 / 250 RC

6.1.7

Hydraulic system – Electric system Slide solenoids (C) over the coil cores, slide on new O-rings (P) and screw on union nut (tighten only after mounting the angle plugs).

C

(Fig. 17)

C

P

17 Insert new seals (R) into the grooves on the 4/3-way valve.

R

(Fig. 18)

R

18 Mount 4/3-way valve (A) to the circulation shut-off valve (V) with cheese-head screws M 5 x 30 8.8.

(Fig. 19) V

S A

S 19

Mounting the 4/3-way valve with circulation shut-off valve Mount 4/3-way valve with hexagon bolts M 8 x 70 8.8 (S), contact washers and nuts.

Screw on union nuts (Ü) of hydraulic lines.

(Fig. 20)

S Ü

20

6.1.8

RHB ROLLANT 250 / 250 RC - 298 332.0

Hydraulic system – Electric system Mount all angle plugs (W) to the solenoid valves with seal (Z). Tighten all union nuts (B).

Check function of 4/3-way valve with circulation shut-off valve and tightness of ports.

(Fig. 21)

B

Z W 21

Removing the NG2 solenoid valve A

1

Important!

Only on comfort version machines!

C

Clean the surroundings of the solenoid valve thoroughly.

Remove all angle plugs (C) from the solenoid valves.

22

Unscrew all union nuts (A) of hydraulic lines from the ports and plug ports with plugs.

Environment!

Dispose of hydraulic oil properly!

Unscrew the nuts and pull out the bolts, then remove solenoid valve.

(Fig. 22, 25)

Disassembling the NG2 solenoid valve D

Unscrew all union nuts (D) and pull off solenoids (19) and (27) from the coil cores.

19

27

(Fig. 23, 25)

27 23

298 332.0 - RHB ROLLANT 250 / 250 RC

6.1.9

Hydraulic system – Electric system Unscrew coil cores (19) and (27) and remove valve cartridges.

Unscrew male connectors (7) and remove spring guide, compression spring and lowering valve.

19 27

Unscrew threaded insert (11) and remove cylinder rollers.

(Fig. 24, 25) 27 7

6.1.10

11

11

7 24

RHB ROLLANT 250 / 250 RC - 298 332.0

Hydraulic system – Electric system

1

3

2

13 17

18 19

4

20

5

20

12 11 6

10 9 8

25

7

26 21

28 27 205492

25 NG 2 solenoid valve, disassembled 1 Valve block 2 Male connector L 10F-M O-ring 3 Male connector L 10F-M Male connector L 8F-M 14 x 1.5 4 Plug 5 Cylinder roller 15 x 15SORT.M 1-M 6 6 Valve cartridge 7 Male connector L 10F-M 12 x 1.5 8 Spring guide 9 Compression spring 10 Lowering valve 11 Threaded insert 12 O-ring 15.3 x 2.2-N 13 Insert M 14 Seal 15 Spool D 5.5 16 Solenoid 3MM 12V 60% FED 17 O-ring 22X2-N 18 Valve cartridge 19 Seal 20 Spool 21 Solenoid 3MM 12V 60% 22 Cheese-head screw M 8 x 60 8.8

298 332.0 - RHB ROLLANT 250 / 250 RC

6.1.11

Hydraulic system – Electric system Assembling the NG2 solenoid valve 12

11

7

A

8

9

Important!

10

Ensure absolute cleanliness during assembly!

Insert lowering valve (10), compression spring (9) and spring guide into the threaded insert (11).

Place new O-ring (A) over the male connector and screw male connector into the threaded insert (11).

26

Place new O-ring (12) over the threaded insert.

(Fig. 25, 26)

Install cylinder rollers (5) into the housing and screw in pre-assembled valve cartridge (6).

(Fig. 25, 27)

6

6

5

5

27 Insert spool (26) into the valve cartridge (21) if it previously has fallen out.

(Fig. 25, 28) 21 26

28

6.1.12

RHB ROLLANT 250 / 250 RC - 298 332.0

Hydraulic system – Electric system Insert new seals (25) and valve cartridges (21) into the threaded bores marked with an arrow.

Screw in coil cores (E440140) (C) with new O-rings and tighten them.

(Fig. 25, 29)

25 21 B C 29

Insert spool (18) into the valve cartridge (13) if it previously has fallen out.

(Fig. 25, 30)

18

13

30 Insert new seals (17) and valve cartridges (13) into the threaded bores marked with an arrow.

Screw in coil cores (E441140) (E) with new O-rings (F) and tighten them.

(Fig. 25, 31)

17 13 F E 31

Slide solenoids (19) and (27) over the coil cores and slide on new O-rings (20).

19

Screw on union nuts (D) (tighten only after mounting the angle plugs).

D

(Fig. 25, 32)

20 27

27 32

298 332.0 - RHB ROLLANT 250 / 250 RC

6.1.13

Hydraulic system – Electric system Mounting the NG2 solenoid valve 1

Place solenoid valve (1) in position, screw in cheese-head screw (28) and tighten it.

(Fig. 25, 33)

28

33 Mount hydraulic lines (G) and hydraulic hoses (H) to the connecting ports.

G

(Fig. 34) H H G

34 Fit all angle plugs (C) with seals (I) to the solenoid valves.

D

Tighten all union nuts (D).

I

Check function of NG2 solenoid valve and tightness of ports.

(Fig. 35)

C

35

6.1.14

RHB ROLLANT 250 / 250 RC - 298 332.0

Hydraulic system – Electric system HYDRAULIC CYLINDERS Removing and installing the hydraulic cylinders D

Important!

The hydraulic tailgate cylinder is described here.

To remove the hydraulic pick-up lift cylinder, remove support (K) (pay attention to the orifice plate on the pressure relief valve (D)).

K

1

To remove the left-hand hydraulic tailgate cylinder, remove rear guard and tension spring of swinging segment.

Close tailgate.

Remove hydraulic hoses (A) from their ports.

Z Environment!

Collect leaking hydraulic oil and dispose of properly!

A A

Drive out expansion pins and remove hydraulic cylinder.

(Fig. 1, 2) 2 Slide on hydraulic cylinder (Z) and secure with washer (C) and expansion pin (B).

C

B

Z Important!

Secure hydraulic pick-up lift cylinder (P) with washer and cotter pin.

Connect hydraulic hoses.

A

Check tightness of connections.

3

(Fig. 3, 4)

P

4

298 332.0 - RHB ROLLANT 250 / 250 RC

6.2.1

Hydraulic system – Electric system Disassembling the hydraulic cylinders 8 Important!

The hydraulic tailgate cylinder is described here.

The hydraulic backwinder and pick-up lift cylinders must be disassembled analogously.

Chuck cylinder tube.

6

5

Turn cylinder head (6) counterclockwise until the safety wire (8) has fully come out of the slot in the cylinder tube.

Pull out cylinder head with connecting rod.

13

12

Chuck connecting rod (3) and remove rod guide ring (13), piston seal (12) and O-ring from the piston (11).

3

11

Important!

The piston has been mounted with liquid locking compound and is therefore tightly seated.

Heat up piston (11) with a hot-air gun and unscrew it from the connecting rod.

6

Pull off cylinder head from the connecting rod.

Remove seals in and on the cylinder head.

(Fig. 5, 6, 7)

6.2.2

RHB ROLLANT 250 / 250 RC - 298 332.0

Hydraulic system – Electric system

1 14

15

12 13 10 11

7 6 4

9

8

5 16

2

17

3

16 17

205509

7 Hydraulic cylinder, disassembled: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

Hydraulic cylinder Lubricating nipple AS 6 x 1 Connecting rod Scraper ring Seal Cylinder head Male connector L 8F-M 14 x 1.5 Safety wire O-ring 34.2 x 3 -N Back-up ring Piston Piston seal Rod guide ring Cylinder tube Restrictor Union Orifice plate Orifice plate 16 Washer 17 Expansion pin 6 x 40-N

298 332.0 - RHB ROLLANT 250 / 250 RC

6.2.3

Hydraulic system – Electric system Assembling the hydraulic cylinders 6

Apply a little oil to the groove (A) and insert back-up ring (10) into the groove of the cylinder head (6).

10

(Fig. 7, 8)

A

8 Install seal (5) into the cylinder head with the dust lip facing the inside and the scraper ring (4) with the stepped edge facing the outside.

4 5

(Fig. 7, 9)

9 Apply a little oil to the seal and the scraper ring in the cylinder head.

3

6

Slide cylinder head (6) on the connecting rod (3).

(Fig. 7, 10)

10 Screw piston (11) on the connecting rod (3), using liquid locking compound (DELO-ML 118).

11

(Fig. 7, 11)

3

11

6.2.4

RHB ROLLANT 250 / 250 RC - 298 332.0

Hydraulic system – Electric system Apply a little oil to the piston and insert O-ring (9) into the groove (C), then install the piston seal (12) above it.

13 B

C

9

12

Insert rod guide ring (13) into the groove (B).

(Fig. 7, 12)

12 Apply oil to the back-up ring on the cylinder head and to the contact face in the cylinder tube (14).

14

Slide connecting rod and cylinder head into the cylinder tube.

(Fig. 7, 13)

13 Turn cylinder head so that the bore (E) in der cylinder head groove is in the centre of the cylinder tube slot.

8

Hang hook (D) of the safety wire (8) into the bore.

Turn cylinder head clockwise until the safety wire has completely disappeared.

D

(Fig. 7, 14)

E

14

298 332.0 - RHB ROLLANT 250 / 250 RC

6.2.5

Hydraulic system – Electric system Disassembling the hydraulic cylinder (knife lift) Unscrew non-return valve from the threaded bore and drain hydraulic oil.

Environment!

Collect hydraulic oil and dispose of properly!

Push snap ring (5) through the threaded bore of the rear groove (A) and rotate piston (2) at the same time.

15

Important!

For more clarity, figure 16 shows the piston (2) when removed.

6 Pull out piston (2).

Remove scraper ring and seal from the hydraulic cylinder (6).

(Fig. 15, 16, 17) A

2

5 16 Hydraulic cylinder, disassembled:

1 2

3

4

5

1 2 3 4 5 6

6

Hydraulic cylinder Piston Scraper ring Seal Snap ring A 22 Hydraulic cylinder

(Fig. 17)

205519

17

Assembling the hydraulic cylinder (knife lift) 6

If previously removed, insert snap ring into the hydraulic cylinder.

Insert seal (4) with the dust lip facing inside and scraper ring (3) into the grooves of the hydraulic cylinder (6).

3

(Fig. 17, 18)

4

18

6.2.6

RHB ROLLANT 250 / 250 RC - 298 332.0

Hydraulic system – Electric system Rub seal, scraper ring and piston with hydraulic oil.

Slide piston (2) into the hydraulic cylinder (6).

Slide snap ring (5) so on the front groove that the opening of the snap ring stands at an angle of 90 degrees to the slot in the piston.

Important!

6

For more clarity, figure 20 shows the correct position of the snap ring on the front groove with the piston removed.

2 19

(Fig. 17, 19, 20)

2

A

5 20 Turn piston so that the slot in the piston is aligned with the threaded bore.

Hold a screwdriver or a punch in front of the slot and force piston into the hydraulic cylinder until the snap ring (5) is located in the rear groove (A).

Screw in non-return valve.

(Fig. 17, 20, 21)

21

298 332.0 - RHB ROLLANT 250 / 250 RC

6.2.7

7 Index

Index INDEX A

F

Adjustment ...............................................................5.1.6 Angle drive, intermediate drive .....................................2.2.1 Assembling and mounting the tying drive ........................2.5.8 Assembling the 4/3-way valve with circulation shut-off valve ............................................................6.1.7 Assembling the angle drive ..........................................2.2.7 Assembling the cam-type cut-out clutch ........................2.1.12 Assembling the cutting rotor/feed rotor ...........................3.3.5 Assembling the cutting unit ........................................4.1.13 Assembling the gauge wheel ........................................3.2.4 Assembling the hydraulic cylinder (knife lift) .....................6.2.6 Assembling the hydraulic cylinders ................................6.2.4 Assembling the net wrapping unit ................................4.2.13 Assembling the NG2 solenoid valve .............................6.1.12 Assembling the twine wrapping unit .............................4.1.14 Assembling the universal drive shaft half (machine side) ....2.1.8 Assembling the universal drive shaft half (tractor side) .......2.1.4 Assembling the valve combination .................................6.1.5

Ferrule fittings on hydraulic lines ...................................1.3.2

B Basic rule ................................................................1.2.3 Bolts .......................................................................1.4.1

C Checking the tightness of tailgate valve combination and hydraulic cylinder .................................................6.1.1 Checking the valve combination ........................................................................6.1.2 Contents .................................................................0.1.1 Correct installation of adapter sleeve bearings .................1.3.2 Correct installation of lock collar bearings ........................1.3.2 Correct use of the round baler ......................................1.2.2 Cutting rotor/feed rotor, disassembled ............................3.3.4 Cutting/feed unit ........................................................3.3.1

D Disassembling the 4/3-way valve with circulation shut-off valve ............................................................6.1.6 Disassembling the angle drive ......................................2.2.2 Disassembling the cam-type cut-out clutch ....................2.1.11 Disassembling the cutting rotor/feed rotor .......................3.3.2 Disassembling the cutting unit ......................................4.1.6 Disassembling the gauge wheel ....................................3.2.1 Disassembling the hydraulic cylinder (knife lift) .................6.2.6 Disassembling the hydraulic cylinders ............................6.2.2 Disassembling the net wrapping unit ..............................4.2.3 Disassembling the NG2 solenoid valve ...........................6.1.9 Disassembling the twine wrapping unit ...........................4.1.3 Disassembling the universal drive shaft half (machine side) 2.1.7 Disassembling the universal drive shaft half (tractor side) ...2.1.1 Disassembling the valve combination .............................6.1.3 Drive chains, left-hand side ..........................................2.4.1 Drive chains/drive belts on right-hand side ......................2.5.1 Drive Diagram ..........................................................2.3.1 Drives, left-hand side ..................................................2.3.1 Drives, right-hand side ................................................2.3.2

298 332.0 - RHB ROLLANT 250 / 250 RC

G Gauge wheel, disassembled ........................................3.2.3 General ...................................................................1.1.1 General repair information ...........................................1.3.1 General safety and accident prevention regulations ...........1.2.2

H Hydraulic cylinder, disassembled ..................................6.2.6 Hydraulic cylinders .....................................................6.2.1 Hydraulic screw fittings ...............................................1.4.2

I Identification of warning and danger signs .......................1.2.2 Important information ..................................................1.2.1 Installing and adjusting the cutting rotor/feed rotor drive ...2.4.10 Installing and adjusting the drive of rollers 1, 2 and 16 ......2.4.12 Installing and tensioning the roller drive (top) ...................2.4.3 Installing roller 11 ....................................................3.4.12 Installing roller 3 ........................................................3.4.6 Installing the angle drive ............................................2.2.14 Installing the cutting rotor/feed rotor ...............................3.3.5 Installing the cutting unit ............................................4.1.21 Installing the deflector ...............................................4.1.19 Installing the feed auger drive (right) ..............................2.5.1 Installing the hydraulic pick-up lift ..................................3.1.2 Installing the intermediate drive of pick-up drive on rotor machines ....................................................2.4.18 Installing the knife shaft .............................................3.3.12 Installing the pick-up and auger ....................................3.2.8 Installing the pick-up drive (left) ...................................2.4.14 Installing the roller drive (front) ......................................2.4.7 Installing the scraper of cutting rotor/feed rotor .................3.3.8 Installing the short crop baffle .......................................3.2.6 Installing the swinging segment ....................................3.5.9 Installing the tailgate roller drive ....................................2.5.3 Introduction ..............................................................1.1.1 Introduction to the CLAAS REPAIR MANUAL ..................1.1.2

K Knife shaft, disassembled ..........................................3.3.11

L Leaving the round baler ..............................................1.2.2 Liquid locking compound .............................................1.3.1 Lubricants chart ........................................................1.5.1

M Mounting the 4/3-way valve with circulation shut-off valve ...6.1.8 Mounting the cam track .............................................3.2.19 Mounting the hydraulic backwinder ................................3.6.3 Mounting the net wrapping unit ...................................4.2.20 Mounting the NG2 solenoid valve ................................6.1.14 Mounting the pick-up ................................................3.2.12 Mounting the tailgate ..................................................5.1.3 Mounting the tine carrier ............................................3.2.19 Mounting the twine wrapping unit ................................4.1.23

7.1.1

Index N

S

Net wrapping ........................................................... 4.2.1

Safety rules ............................................................. 1.2.1 Self-locking bolts ...................................................... 1.3.1 Service ................................................................... 1.2.3 Some advice for speedy and correct repair work .............. 1.3.4 Spare parts ............................................................. 1.3.1 Specifications ........................................................... 1.5.1 Swinging segment ..................................................... 3.5.1

P Pick-up ................................................................... 3.2.1 Pick-up lift ............................................................... 3.1.1 Progressive ring fittings on hydraulic lines ...................... 1.3.3

R Reason of damage .................................................... 1.3.1 Remove tailgate. ...................................................... 3.4.9 Removing and disassembling the tying drive ................... 2.5.6 Removing and installing the hydraulic cylinders ............... 6.2.1 Removing and installing the net wrapping/ twine wrapping drives .............................................. 2.5.11 Removing roller 11 .................................................... 3.4.9 Removing roller 3 ..................................................... 3.4.1 Removing the 4/3-way valve with circulation shut-off valve ........................................................... 6.1.6 Removing the angle drive ........................................... 2.2.1 Removing the cam track ........................................... 3.2.13 Removing the cutting rotor/feed rotor ............................. 3.3.1 Removing the cutting rotor/feed rotor drive ..................... 2.4.9 Removing the cutting unit ........................................... 4.1.2 Removing the deflector .............................................. 4.1.3 Removing the drive of rollers 1, 2 and 16 ..................... 2.4.11 Removing the drive shaft .......................................... 3.2.16 Removing the feed auger drive (right) ............................ 2.5.1 Removing the gauge wheel ......................................... 3.2.1 Removing the guide rollers ....................................... 3.2.15 Removing the hydraulic pick-up lift ................................ 3.1.1 Removing the intermediate drive of pick-up drive on rotor machines ................................................... 2.4.17 Removing the knife shaft ............................................ 3.3.9 Removing the net wrapping unit ................................... 4.2.1 Removing the NG2 solenoid valve ................................ 6.1.9 Removing the pick-up .............................................. 3.2.11 Removing the pick-up and auger .................................. 3.2.6 Removing the pick-up drive (left) ................................ 2.4.13 Removing the roller drive (front) ................................... 2.4.6 Removing the roller drive (top) ..................................... 2.4.1 Removing the scraper of cutting rotor/feed rotor ............... 3.3.8 Removing the short crop baffle .................................... 3.2.5 Removing the swinging segment .................................. 3.5.1 Removing the tailgate ................................................ 5.1.1 Removing the tailgate roller drive ................................. 2.5.2 Removing the tine carrier .......................................... 3.2.16 Removing the twine wrapping unit ................................ 4.1.1 Removing the valve combination .................................. 6.1.2 Replacing the left-hand drive shaft lock collar bearing ....... 3.2.9 Replacing the mechanical backwinder ........................... 3.6.7 Replacing the right-hand drive shaft lock collar bearing ... 3.2.10 Replacing the spring tine ............................................ 3.2.6

7.1.2

T Taper fittings on hydraulic lines .................................... 1.3.3 Taper ring fasteners .................................................. 1.3.1 Tensioning the steel roller chains .................................. 1.3.1 Tightening torques .................................................... 1.4.1 Transmission ........................................................... 1.3.1

U Universal Drive Shaft ................................................. 2.1.1

W Welding .................................................................. 1.3.3

RHB ROLLANT 250 / 250 RC - 298 332.0

Following the policy of CLAAS KGaA mbH to improve their products as technical developments continue, CLAAS reserve the right to make alterations which must not necessarily correspond to text and illustrations contained in this publication, and without incurring obligation to alter any machines previously delivered.

Technical data, dimensions and weights are given as an indication only. Responsibility for errors and omissions not accepted.

Reproduction or tanslation of this publication, in whole or in part, is not permitted without the written consent of CLAAS KGaA mbH. All rights under the provision of the Copyright Act are reserved.

CLAAS KGaA mbH D - 33426 HARSEWINKEL Germany

Our contribution to the environment: CLAAS have printed this manual on 100% chlorine free paper.

298 332.0 CLAAS KGaA mbH D - 33426 HARSEWINKEL Germany

RHB ROLLANT 250 / 250 RC GB - 07.02 - 100 - BO Printed in Germany