CAT Bucyrus RH 170B Hydraulic Excavator Operating Instruction Manual 3725013 - PDF DOWNLOAD

OPERATING INSTRUCTIONS RH170B Electric

Hydraulic Excavator RH170B Electric No. Bucyrus HEX GmbH

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric

Published by:

Bucyrus HEX GmbH Dept. 2470 – Documentation D-44149 Dortmund, Karl-Funke-Straße 36 Tel. 49 (0) 231 922-4340 Fax 49 (0) 231 922-5340 www.bucyrus.com www.bucyrus-hex.com

© Copyright Bucyrus HEX GmbH 2011. The reproduction, distribution and utilization of this manual / file as well as the communication of its content to others without express authorization is prohibited. Offenders will be held liable for the payment of damages. All rights reserved in the event of the grant of a patent, utility model or design.

Printed in Germany

ii

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric

The Bucyrus HEX operating manual is in 6 sections; the sections are designed for different target groups: Operating instructions

Target group

Part 1 INTRODUCTION FUNDAMENTAL SAFETY INSTRUCTIONS

Operating personnel + Inspection and servicing personnel + Repair personnel

Part 2 OPERATION

Operating personnel The operating personnel must have knowhow relevant to the operation and the application of this or comparable machines.

Part 3 INSPECTION AND SERVICING Part 4 REPAIR WORK

Inspection and servicing personnel The inspection and servicing personnel must have know-how relevant to the inspection and servicing of this or comparable machines.

Repair personnel The repair personnel must have know-how and experience relevant to the repair of this or comparable machines.

Part 5 ANNEX

Part 6 INDEX

BA RH170B(3 725 013.00)-EN

Operating personnel + Inspection and servicing personnel + Repair personnel Operating personnel + Inspection and servicing personnel + Repair personnel

iii

OPERATING INSTRUCTIONS RH170B Electric

iv

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Table of contents TABLE OF CONTENTS 1 INTRODUCTION __________________________________________________________________ 1-1 PREFACE _______________________________________________________________________ 1-3 WARRANTY______________________________________________________________________ 1-4 FUNDAMENTAL SAFETY INSTRUCTIONS _____________________________________________ 1-5 Warnings and symbols ____________________________________________________________ 1-5 DESIGNATED USE ________________________________________________________________ 1-6 ORGANIZATIONAL MEASURES _____________________________________________________ 1-7 Selection and qualification of personnel; basic responsibilities______________________________ 1-8 Safety instructions governing specific operational phases _________________________________ 1-8 Special work in conjunction with utilization of the machine and maintenance and repairs as well as troubleshooting during work; disposal of parts and consumables____________________________ 1-9 Warning of special dangers________________________________________________________ 1-10 Transporting and recommissioning __________________________________________________ 1-11 ACCIDENT PREVENTION REGULATIONS FOR ELECTRICALLY POWERED EXCAVATORS____ 1-12 Safety instructions for excavators with electric motor ____________________________________ 1-13 FIRE AND EXPLOSION HAZARD____________________________________________________ 1-14 NOTES_________________________________________________________________________ 1-15 2 OPERATION _____________________________________________________________________ 2-1 OPERATION - SAFETY INSTRUCTIONS _______________________________________________ 2-3 Operating Instructions, where to store it in the driver’s cab ________________________________ 2-4 FIRE AND EXPLOSION HAZARD_____________________________________________________ 2-5 DESCRIPTION OF THE EXCAVATOR _________________________________________________ 2-6 Excavator layout _________________________________________________________________ 2-7 Undercarriage ___________________________________________________________________ 2-8 Superstructure___________________________________________________________________ 2-8 Drive __________________________________________________________________________ 2-8 Hydraulic system _________________________________________________________________ 2-8 Pump Managing System (PMS) _____________________________________________________ 2-8 Stored Program Control (SPC) ______________________________________________________ 2-8 Control Management System (CMS) _________________________________________________ 2-8 Demand control / Zero-flow regulation ________________________________________________ 2-9 Board-Control-System (BCS) _______________________________________________________ 2-9 Electrical system _________________________________________________________________ 2-9 Signs _________________________________________________________________________ 2-11 Entering and leaving the machine, Safety instructions ___________________________________ 2-24 Access lighting _________________________________________________________________ 2-24 Swinging ladder_________________________________________________________________ 2-25 Folding ladder (optional) __________________________________________________________ 2-26 Escape ladder (optional) __________________________________________________________ 2-27 Cab interior lamp ________________________________________________________________ 2-28 Servicing lighting ________________________________________________________________ 2-29 Illuminating the control column _____________________________________________________ 2-29

BA RH170B(3 725 013.00)-EN

v

OPERATING INSTRUCTIONS RH170B Electric Table of contents EMERGENCY STOP switch _______________________________________________________ 2-30 Servicing switch_________________________________________________________________ 2-31 Windscreen washer______________________________________________________________ 2-31 Driver's seat ___________________________________________________________________ 2-32 Fire extinguisher ________________________________________________________________ 2-34 Automatic fire-extinguishing system (optional) _________________________________________ 2-35 Trainer's / instructor's seat ________________________________________________________ 2-35 Emergency escape device (optional) ________________________________________________ 2-36 MONITORING, WARNING AND CONTROL ELEMENTS __________________________________ 2-40 PUTTING THE MACHINE INTO OPERATION __________________________________________ 2-62 Service station (tanklift) ___________________________________________________________ 2-62 Battery main switch, switching on and off _____________________________________________ 2-65 Electrical system (24V), switching on and off __________________________________________ 2-65 Switching the electric motor on and off _______________________________________________ 2-66 Time-out before restart ___________________________________________________________ 2-67 Electric motor can not be switched on________________________________________________ 2-68 In case of failure ________________________________________________________________ 2-68 Circuit breaker, switching on and off _________________________________________________ 2-69 Motor protection relay, function _____________________________________________________ 2-71 Air conditioner (optional) __________________________________________________________ 2-73 TRAVELLING THE MACHINE _______________________________________________________ 2-74 Travelling, Safety Instructions ______________________________________________________ 2-74 Travelling______________________________________________________________________ 2-75 Superstructure holding brake ______________________________________________________ 2-79 Track parking brake _____________________________________________________________ 2-79 TRANSPORTING THE MACHINE____________________________________________________ 2-80 Transport - Safety instructions _____________________________________________________ 2-80 WORKING OPERATION ___________________________________________________________ 2-81 Safety instructions _______________________________________________________________ 2-81 Working equipment, avoid extreme positions __________________________________________ 2-82 WORKING OPERATION ___________________________________________________________ 2-83 Before starting work _____________________________________________________________ 2-83 Swinging the superstructure _______________________________________________________ 2-83 Braking the superstructure ________________________________________________________ 2-83 Working _______________________________________________________________________ 2-84 Emergency lowering of the working equipment_________________________________________ 2-85 After daily operation _____________________________________________________________ 2-85 ASSEMBLING WORKING EQUIPMENT - SAFETY INSTRUCTIONS ________________________ 2-86 Securing the machine ____________________________________________________________ 2-87

vi

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Table of contents CORROSION PROTECTION FOR PINS AND BEARINGS (BUSHINGS AND HUBS)____________ 2-88 NOTES_________________________________________________________________________ 2-89 3 INSPECTION AND SERVICING ______________________________________________________ 3-1 SAFETY INSTRUCTIONS FOR EXCAVATORS WITH ELECTRIC MOTOR ____________________ 3-3 INSPECTION AND SERVICING - SAFETY INSTRUCTIONS________________________________ 3-5 FIRE AND EXPLOSION HAZARD____________________________________________________ 3-11 INSPECTION AND SERVICING PLANS - INSTRUCTIONS ________________________________ 3-13 Intervals_______________________________________________________________________ 3-13 Oils / Greases __________________________________________________________________ 3-13 Cleaning jobs __________________________________________________________________ 3-13 Components ___________________________________________________________________ 3-13 Plan V ________________________________________________________________________ 3-15 Plan N ________________________________________________________________________ 3-17 Plan T and W___________________________________________________________________ 3-19 Plan A – E _____________________________________________________________________ 3-21 LUBRICATING CHART – GREASE___________________________________________________ 3-26 Lubricating chart – Grease (legend) _________________________________________________ 3-26 Filling quantities - Grease _________________________________________________________ 3-27 INSPECTION PLAN - OIL __________________________________________________________ 3-28 Inspection plan – Oil (legend) ______________________________________________________ 3-29 Filling quantities - oil _____________________________________________________________ 3-30 Filling quantities - other ___________________________________________________________ 3-30 LUBRICANTS ___________________________________________________________________ 3-31 Notes on the selection of oils and greases ____________________________________________ 3-31 Avoid mixing of different hydraulic fluids ______________________________________________ 3-31 I. Oils for combustion engines (On-Board Crane, optional) ______________________________ 3-32 II. Oil for hydraulic system ______________________________________________________ 3-33 III.a Oils for pump gearbox _____________________________________________________ 3-34 III.b Oils for swing gearboxes ___________________________________________________ 3-35 III.c Oils for travel gearboxes ___________________________________________________ 3-36 V. Greases for bearings and slewing rings _________________________________________ 3-37 SERVICING WORK _______________________________________________________________ 3-38 Hose line for oil change___________________________________________________________ 3-38 ELECTRIC MOTOR _______________________________________________________________ 3-39 Electric motor - Safety instructions __________________________________________________ 3-39 Cleaning the electric motor ________________________________________________________ 3-39 Electric motor, greasing___________________________________________________________ 3-40 ELECTRICAL SYSTEM ____________________________________________________________ 3-41 Electrical system - Safety instructions________________________________________________ 3-41 Battery ________________________________________________________________________ 3-42 Battery main switch, switching on and off _____________________________________________ 3-43 Removing and installing the battery _________________________________________________ 3-44 Switchgear cabinet ______________________________________________________________ 3-45 Slip ring maintenance ____________________________________________________________ 3-48

BA RH170B(3 725 013.00)-EN

vii

OPERATING INSTRUCTIONS RH170B Electric Table of contents Floodlight projector, replacing the lamp ______________________________________________ 3-49 HYDRAULIC SYSTEM_____________________________________________________________ 3-51 Hydraulic system - Safety instructions _______________________________________________ 3-51 Depressurizing the hydraulic system_________________________________________________ 3-51 Checking the hydraulic oil level _____________________________________________________ 3-52 Replacing the hydraulic oil return-flow filters (hydraulic oil reservoir) ________________________ 3-54 Bypass valves (hydraulic oil reservoir) _______________________________________________ 3-56 Breather filter, replace ____________________________________________________________ 3-57 Filter (control circuit) _____________________________________________________________ 3-58 High-pressure filter for working hydraulics ____________________________________________ 3-59 High-pressure filters for the servo circuit______________________________________________ 3-60 High-pressure filters for swinging circuits _____________________________________________ 3-61 Changing the hydraulic oil _________________________________________________________ 3-62 Venting the hydraulic system ______________________________________________________ 3-66 Cleaning the hydraulic oil cooler ____________________________________________________ 3-67 Electronic excavator control _______________________________________________________ 3-68 Pressure accumulator - Emergency lowering __________________________________________ 3-69 PUMP TRANSFER GEARBOX ______________________________________________________ 3-70 Checking the gearbox oil level / Topping up with oil _____________________________________ 3-70 Pump transfer gearbox, checking pre chambers oil level _________________________________ 3-71 Pump transfer gearbox, changing oil_________________________________________________ 3-72 Pump transfer gearbox, venting ____________________________________________________ 3-72 Pre-chambers working pumps, draining oil, changing oil _________________________________ 3-73 Pre-chambers swing pumps, draining oil, changing oil ___________________________________ 3-73 Pump transfer gearbox lube oil filter, replace __________________________________________ 3-74 SLEWING GEARBOX _____________________________________________________________ 3-75 Gearbox - Checking the oil level / Topping up with oil ___________________________________ 3-75 Changing the gearbox oil _________________________________________________________ 3-75 Gearbox venting ________________________________________________________________ 3-76 SWING GEARBOX _______________________________________________________________ 3-77 Gearbox - Checking the oil level / Topping up with oil ___________________________________ 3-77 Changing the gearbox oil _________________________________________________________ 3-78 Gearbox venting ________________________________________________________________ 3-79 TRAVEL GEARBOX ______________________________________________________________ 3-80 Gearbox - Checking the oil level / Topping up with oil ___________________________________ 3-80 Pre-chamber / spur wheel section, Check the oil level / Top up with oil ______________________ 3-80 Hydraulic motor chamber - Check the oil level / Top up with oil ____________________________ 3-80 Travel gearbox, Changing oil ______________________________________________________ 3-81 Pre-chamber / spur wheel section, Changing oil________________________________________ 3-81 Hydraulic motor chamber, Changing oil ______________________________________________ 3-82 Breather filter, Clean / Replace _____________________________________________________ 3-82 CRAWLER TRACKS ______________________________________________________________ 3-83 Track / support rollers, greasing ____________________________________________________ 3-84 Track roller / support roller, fastening ________________________________________________ 3-84 Track tensioner _________________________________________________________________ 3-85 Pressure-accumulator inspection regulations __________________________________________ 3-86 Checking the gas charging pressure in the pressure accumulator __________________________ 3-86

viii

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Table of contents SWING RING ____________________________________________________________________ 3-87 Swing ring - Instructions __________________________________________________________ 3-87 Bearing races __________________________________________________________________ 3-87 CENTRAL LUBRICATING __________________________________________________________ 3-89 Design and function______________________________________________________________ 3-89 Function ______________________________________________________________________ 3-90 Filling up the grease container _____________________________________________________ 3-91 Breather filter___________________________________________________________________ 3-91 Checking the greasing pressure ____________________________________________________ 3-92 Checking the greasing pressure ____________________________________________________ 3-93 Unblocking a grease line. _________________________________________________________ 3-94 Unblocking a grease line. _________________________________________________________ 3-94 Oilfilter (hydraulic circuit grease pump) )______________________________________________ 3-95 Grease filter (Filling the grease container) ____________________________________________ 3-96 Grease filter (Grease lines) ________________________________________________________ 3-97 OTHER MAINTENANCE ___________________________________________________________ 3-98 Air intake filters _________________________________________________________________ 3-98 HYDRAULIC LADDER (OPTIONAL) _________________________________________________ 3-100 Pressure-accumulator inspection regulations _________________________________________ 3-101 Extract from the German regulations _______________________________________________ 3-101 Checking the gas charging pressure in the pressure accumulator _________________________ 3-101 PUTTING THE EXCAVATOR OUT OF OPERATION AND RECOMMISSIONING ______________ 3-102 Putting the excavator out of operation_______________________________________________ 3-105 Battery storage ________________________________________________________________ 3-105 Recommissioning ______________________________________________________________ 3-105 NOTES________________________________________________________________________ 3-107 4 REPAIR WORK ___________________________________________________________________ 4-1 SAFETY INSTRUCTIONS FOR EXCAVATORS WITH ELECTRIC MOTOR ____________________ 4-3 REPAIR WORK - SAFETY INSTRUCTIONS_____________________________________________ 4-5 FIRE AND EXPLOSION HAZARD_____________________________________________________ 4-7 HYDRAULIC SYSTEM______________________________________________________________ 4-8 Repair instructions _______________________________________________________________ 4-8 Hydraulic hoses – Instructions ______________________________________________________ 4-8 PRESSURE ACCUMULATORS - SAFETY INSTRUCTIONS ________________________________ 4-9 WELDING OPERATIONS - SAFETY INSTRUCTIONS____________________________________ 4-10 NOTES_________________________________________________________________________ 4-11 5 ANNEX__________________________________________________________________________ 5-1 TROUBLESHOOTING ______________________________________________________________ 5-3 Instructions on troubleshooting ______________________________________________________ 5-3 Layout of the fault table ____________________________________________________________ 5-3 Possible causes _________________________________________________________________ 5-3 Measures ______________________________________________________________________ 5-3

BA RH170B(3 725 013.00)-EN

ix

OPERATING INSTRUCTIONS RH170B Electric Table of contents Section ________________________________________________________________________ 5-3 FAULT TABLES ___________________________________________________________________ 5-4 Working hydraulics – Fault table _____________________________________________________ 5-4 Track drive – Fault table ___________________________________________________________ 5-5 Slewing mechnism – Fault table _____________________________________________________ 5-6 Central lubricating system – Fault table _______________________________________________ 5-7 HYDRAULIC CIRCUIT DIAGRAM _____________________________________________________ 5-8 ABBREVIATIONS _________________________________________________________________ 5-9 ABBREVIATIONS ________________________________________________________________ 5-10 TECHNICAL DATA _______________________________________________________________ 5-11 6 INDEX __________________________________________________________________________ 6-1

x

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Introduction 1 INTRODUCTION Operating instructions

Target group

Part 1 INTRODUCTION FUNDAMENTAL SAFETY INSTRUCTIONS

Operating personnel + Inspection and servicing personnel + Repair personnel

Part 2 OPERATION

Operating personnel The operating personnel must have knowhow relevant to the operation and the application of this or comparable machines.

Part 3 INSPECTION AND SERVICING Part 4 REPAIR WORK

Inspection and servicing personnel The inspection and servicing personnel must have know-how relevant to the inspection and servicing of this or comparable machines.

Repair personnel The repair personnel must have know-how and experience relevant to the repair of this or comparable machines.

Part 5 ANNEX

Part 6 INDEX

BA RH170B(3 725 013.00)-EN

Operating personnel + Inspection and servicing personnel + Repair personnel Operating personnel + Inspection and servicing personnel + Repair personnel

1-1

OPERATING INSTRUCTIONS RH170B Electric Introduction

1-2

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Introduction PREFACE These operating instructions are designed to familiarize the operator with the machine and its designated use.

The operating instructions contain important information on how to operate the machine safely, properly and with maximum efficiency. Observing these instructions helps to prevent hazardous situations, to reduce repair costs and downtimes and to increase the reliability and service life of the machine.

The operating instructions must be supplemented by the respective national rules and regulations for accident prevention and environmental protection.

The operating instructions must always be available in the driver's cab of the machine.

All Bucyrus HEX operating manuals are issued in German and then translated. Even a good translation may give rise to questions which Bucyrus HEX will be pleased to answer.

The operating instructions are not work instructions for carrying out major repairs. Such work is willingly done for you by the responsible service personal.

The documentation relating to the machine is listed according to scope, quantity and language in the shipping note of the machine or in the covering letter if supplied separately. The operating instructions and spare-parts list are marked with the serial number of the machine.

On taking receipt of the consignment, please check that the documentation is complete and in the language requested by you.

The operating instructions must be read and put into practice by any person in charge of carrying out work with or on the machine, such as  operation, including setting-up, troubleshooting in the course of work, care, evacuation of production waste and disposal of fuels and consumables, 

maintenance (inspection, servicing, repair) and / or



transport.

In addition to the operating instructions and the mandatory rules and regulations for accident prevention and environmental protection in the user's country and at the place where the machine is to be used, the generally recognized technical rules 1 for safe and proper working must be observed The operating instructions are directed to the mining-machine specialist. They cannot provide basic know-how. This can be acquired, for example, in several days' instruction by a qualified Bucyrus HEX mechanic or by attending an Bucyrus HEX training course for operators or maintenance personnel.

The service personal responsible for you will be pleased to deal with any queries you may have after reading through the operating instructions.

1

Complies with VDMA recommendation "Operating instructions"

BA RH170B(3 725 013.00)-EN

1-3

OPERATING INSTRUCTIONS RH170B Electric Introduction WARRANTY The warranty of Bucyrus HEX presupposes among other things that the servicing works as described in the operating instructions have been performed:

Do not operate the machine  when components / assemblies are defective or missing,



by the Bucyrus HEX Service



in a workshop authorized in writing by Bucyrus HEX,

In cases of doubt seek advice from the Bucyrus HEX Service.

by using the original spare parts of Bucyrus HEX.

Bucyrus HEX refuses to assume the guaranteee for damage and consequential damage caused by an abusive utilization of the machine.

or  and 

The proper execution of the servicing works must be documented on the Bucyrus HEX Service checklists.

if one or several of such components of which more than one are installed in the machine have been removed.

Therefore: Do not operate the machine,  when several track rollers or support rollers have been removed; 

when one or several slewing gearboxes have failed or been removed;



when one or several teeth on the backhoe or on the shovel are worn or missing;



when parts of the hardfacing layer on the backhoe or on the shovel are worn or missing.

Working under these circumstances results in heavy wear and possibly in severe damage and thus in high repair costs.

Such circumstances are considered by Bucyrus HEX as "abusive utilization".

Why? The machines have been designed and built on the basis of detailed calculations and so that all of the components installed absorb the occurring forces and are thus loaded to an equal extent.

Example: If the machine is used for working with, for instance, one or even several track rollers removed, the forces must be absorbed by the remaining track rollers. These are then overloaded or loaded to a greater extent than calculated.

The consequences are higher wear and consequential damage to the track rollers, but also to other components of the machine: chassis, travel gearbox and crawler track.

1-4

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Introduction FUNDAMENTAL SAFETY INSTRUCTIONS Complies with VDMA recommendation "Operating Instructions"

Warnings and symbols The following signs are used in the operating instructions to designate instructions of particular importance: Precautionary rules and measures designed to protect the machine operator and other persons from lifethreatening danger or injuries and to prevent extensive damage.

Information and precautionary measures designed to prevent damage to the machine or other property.

BA RH170B(3 725 013.00)-EN

1-5

OPERATING INSTRUCTIONS RH170B Electric Introduction DESIGNATED USE The machine has been built in accordance with state-of-art standards and the recognized safety rules. Nevertheless, its use may constitute a risk to life and limb for the user or third parties or cause damage to the machine and to other material property (acceptable risk) An acceptable risk is present, e.g.: loose material or material to be loaded may drop out of the bucket or backhoe while the working equipment is being swivelled.

The machine must be used only in technically perfect condition in accordance with its designated use and the instructions set out in the operating instructions, and only by safety-conscious persons who are fully aware of the risks involved in operating the machine. Any functional disorders, especially those affecting the safety of the machine, should therefore be rectified immediately.

The excavator with loading bucket attachment is designed solely for excavating and loading:  excavated soils, 

sand,



gravel,



blasted rock,



ore,



coal,

and other raw materials.

Operating the machine within the limits of the desigated use also involves observing the instructions set out in the operating instructions and complying with the inspection and maintenance directives.

Using the excavator or its attachments for purposes other than or extending beyond those stated above, e.g.:  for lifting or transporting persons, 

as a working platform,



for lifting crane loads without the equipment being approved for this purpose,



for driving in posts, sheetpiles supports, etc. without the equipment being approved for this purpose,



for towing machines

is considered contrary to the designated use.

Lifting eyes on the lower carriage -

are settled for transporting with a crane only.

-

must not be used for towing a machine.

Improper use may involve a life-threatening risk for operators or other personnel or may cause injury or extensive damage.

The manufacturer/supplier cannot be held liable for any damage resulting from other than the designated use. The risk involved in such misuse lies with the user.

Noise emission specifications in acc. with the 3rd Ordinance of the Machine Safety Act of 18th January 1991 resp. with EC Machine Directive, Annex I, para. 1.7.4 f.

If the earth-moving machine is operated in accordance with the designated use, the installation of driver´s seats complying with ISO 7096 ensures that the considered vibration accelerations azw (measured as per ISO 2631, Part 1) fulfill the requirements of protecting the driver against wholebody vibration acc. to directive 2002/44/EG.

1-6

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Introduction ORGANIZATIONAL MEASURES The operating instructions must always be at hand at the place of use of the machine, e.g. by stowing them in the place provided for such purpose.

In addition to the operating instructions, observe and instruct the user in all other generally applicable legal and other mandatory regulations relevant to accident prevention and environmental protection.

Personal protective equipment and the working clothing Depending on the cleaning, servicing and/or repair activities to be performed, the personal protective equipment and the working clothing may consist of the following items: 

fall arresters



protective suit

These compulsory regulations may also deal with the handling of hazardous substances, issuing and/or wearing of personal protective equipment or traffic regulations.



helmet



goggles - e. g. for cleaning work - or for welding work

The operating instructions must be supplemented by instructions covering the duties involved in supervising and notifying special organizational features, such as job organization, working sequences or the personnel entrusted with the work.



protective gloves - e.g. for work on hot units - for grinding and welding work



protective working gloves - e.g. for fitting work - for grinding and welding work



ear protectors

Personnel entrusted with work on the machine must have read the operating instructions and in particular the chapter on safety before beginning work. Reading the operating instructions after work has begun is too late. This applies especially to persons working only occasionally on the machine, e.g. during setting up or maintenance.

Check - at least from time to time - whether the personnel is carrying out the work in compliance with the operating instructions and paying attention to risks and safety factors.

For reasons of security, long hair must be tied back or otherwise secured, garments must be close-fitting and no jewellery, such as rings, may be worn. Injury may result from being caught up in the machinery or from rings catching on moving parts.

Use protective equipment wherever required by the circumstances or by law.

Observe all safety instructions and warnings attached to the machine.

See to it that safety instructions and warnings attached to the machine are always complete and perfectly legible.

In the event of safety-relevant modifications or changes in the behaviour of the machine during operation, stop the machine immediately and report the malfunction to the competent authority/person.

Never make any modifications, additions or conversions which might affect safety without the supplier's approval. This also applies to the installation and adjustment of safety devices and valves as well as to welding work on load-bearing elements.

Use only the original sparts parts of Bucyrus HEX. They are the only ones to fulfill the technical specifications of the machine.

Replace hydraulic hoses within stipulated and appropriate intervals, even if no safety-relevant defects have been detected.

Adhere to prescribed intervals or those specified in the operating instructions for routine checks and inspections.

For the execution of maintenance work, tools and workshop equipment adapted to the task on hand are absolutely indispensable.

The personnel must be familiar with the location and operation of fire extinguishers.

Observe all fire-warning and fire-fighting procedures.

BA RH170B(3 725 013.00)-EN

1-7

OPERATING INSTRUCTIONS RH170B Electric Introduction Selection and qualification of personnel; basic responsibilities

Safety instructions governing specific operational phases

Any work on and with the machine must be executed by reliable personnel only. Statutory minimum age limits must be observed.

Standard operation

Employ only trained or instructed staff and set out clearly the individual responsibilities of the personnel for operation, set-up, maintenance and repair.

Make sure that only authorized personnel works on or with the machine.

Define the machine operator's responsibilities giving the operator the authority to refuse instructions by third parties that are contrary to safety.

Do not allow persons to be trained or instructed or persons taking part in a general training course to work on or with the machine without being permanently supervised by an experienced person.

Work on the electrical system and equipment of the machine must be carried out only by a skilled electrician or by instructed persons under the supervision and guidance of a skilled electrician and in accordance with electrical engineering rules and regulations.

Work on chassis and brake systems must be performed by skilled personnel only, which has been specially trained for such work.

Work on hydraulic systems must be carried out only by personnel with special knowledge and experience of hydraulic equipment.

Avoid any operational mode that might be prejudicial to safety.

Before beginning work, familiarize yourself with the surroundings and circumstances of the site, such as obstacles in the working area and the bearing capacity of the soil.

Take the necessary precautions to ensure that the machine is in a safe and reliable state.

Operate the machine only if all protective and safety-oriented devices, such as removable safety devices, emergency shut-off equipment, soundproofing elements and exhausters, are in place and fully functional.

Check the machine at least once per working shift for obvious damage and defects. Report any changes (incl. changes in the machine's working behaviour) to the competent organization/person immediately. If necessary, stop the machine immediately and lock it.

In the event of malfunction, stop the machine immediately and lock it. Have any defects rectified immediately.

Start the machine from the driver's seat only.

During start-up and shut-down procedures always watch the indicators in accordance with the operating instructions.

Before setting the machine in motion, make sure that nobody is at risk.

Before starting work or travelling with the machine, check that braking, signalling and lighting systems are fully functional.

Before setting the machine in motion always check that the accessories have been safely stowed away.

In conditions of poor visibility and after dark always switch on the lighting system.

Persons accopanying the driver must be seated on the passenger seat provided for this purpose.

When crossing underpasses and bridges or when passing under overhead lines always make sure that there is sufficient clearance.

Always keep a distance from the working face and from slopes.

Avoid any operation that might be a risk to machine stability.

Never travel across slopes; always keep the working equipment and the load close to the ground, especially when travelling downhill.

On sloping terrain always adapt your travelling speed to the prevailing ground conditions.

1-8

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Introduction Before leaving the driver's seat always secure the machine against inadvertent movement and unauthorized use. Shut off the electric motor.

Special work in conjunction with utilization of the machine and maintenance and repairs as well as troubleshooting during work; disposal of parts and consumables Observe the adjusting, maintenance and inspection activities and intervals set out in the operating instructions, including information on the replacement of parts and equipment. These activities may be executed by skilled personnel only.

Brief operating personnel before beginning special operations and maintenance work, and appoint a person to supervise the activities.

In any work concerning the operation, conversion or adjustment of the machine and its safetyoriented devices or any work related to maintenance, inspection and repair, always observe the start-up and shut-down procedures set out in the operating instructions and the information on maintenance work.

Ensure that the maintenance area is adequately secured.

If the machine is completely shut down for maintenance and repair work, it must be secured against inadvertent starting by:  removing the ignition key and  attaching a warning sign.

Carry out maintenance and repair work only if the machine is positioned on stable and level ground and has been secured against inadvertent movements.

To avoid the risk of accidents, individual parts and large assemblies being moved for replacement purposes should be carefully attached to lifting tackle and secured. Use only suitable and technically perfect lifting gear and suspension systems with adequate lifting capacity. Never work or stand under suspended loads.

The fastening of loads and the instructing of crane operators should be entrusted to experienced persons only. The marshaller giving the instructions must be within sight or sound of the operator.

For carrying out overhead assembly work always use specially designed or otherwise safetyoriented ladders and working platforms. Never use machine parts as a climbing aid Wear a safety harness when carrying out maintenance work at heights above 1 m.

Wear an approved harness equipped with fall arresters and safety lines.

BA RH170B(3 725 013.00)-EN

1-9

OPERATING INSTRUCTIONS RH170B Electric Introduction Keep all handles, steps, handrails, platforms, landings and ladders free from dirt, snow and ice.

Clean the machine, especially connections and threaded unions, of any traces of oil, fuel or preservatives before carrying out maintenance/repair.

Never use aggressive detergents. Use lint-free cleaning rags.

Before cleaning the machine with water, steam jet (high-pressure cleaning) or detergents, cover or tape up all openings which - for safety and functional reasons - must be protected against water, steam or detergent penetration. Special care must be taken with electric motors and switch-gear cabinets.

Ensure during cleaning of the machine that the temperature sensors of the fire-warning and firefighting systems do not come into contact with hot cleaning agents as this might activate the firefighting system.

After cleaning remove all covers and tapes applied for that purpose.

After cleaning, examine all fuel, lubricant, brake and hydraulic fluid lines for leaks, loose connections, chafe marks and damage. Any defect found must be rectified without delay.

Always tighten any screwed connections that have been loosened during maintenance and repair.

Any safety devices removed for set-up, maintenance or repair purposes must be refitted and checked immediately upon completion of maintenance and repair work.

Ensure that all consumables and replaced parts are disposed of safely and with minimum environmental impact.

Warning of special dangers Electric energy Use only original fuses with the specified current rating. Switch off the machine immediately if trouble occurs in the electrical system.

When working with the machine, maintain a safe distance from overhead electric lines. If work is to be carried out close to overhead lines, the working equipment must be kept well away from them.

Caution, danger! Check out the prescribed safety distances.

If your machine comes into contact with a live wire  do not leave the machine  drive the machine out of the hazard zone; warn others against approaching and touching the machine  have the live wire de-energized  do not leave the machine until the damaged or contacted line has been safely de-energized.

The electrical equipment of machines is to be inspected and checked at regular intervals. Defects such as loose connections or scorched cables must be rectified immediately.

High-voltage system Floodlamps equipped with gaz discharge lamps require a high-voltage supply (ca. 25 kV).

The high voltage is generated by a ballast unit.

Switch off the electrical system of the excavator before touching the lamp or the ballast unit.

Battery Warning! Battery Posts, terminals and related accessories contain lead and lead compounds, chemicals known to cause cancer and reproductive harm. Wash hands after handling

1-10

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Introduction Gas, dust, steam and smoke

Noise

Always start and operate the engine in a wellvented area;

During operation, all sound baffles of the machine must be closed.

If in an enclosed area, vent the exhaust to the outside;

Always wear the prescribed ear protectors.

Do not modify or tamper with the exhaust system

Oil, grease and other chemical substances

Diesel engine exhaust and some of its constituents are known to cause cancer, birth defects, and other reproductive harm Operate fuel-operated heating systems only on adequately ventilated premises. Before starting the machine on enclosed premises, make sure that there is sufficient ventilation.

Observe the regulations in force at the respective site.

Carry out welding, flame-cutting and grinding work on the machine only if this has been expressly authorized, as there may be a risk of explosion and fire.

Before carrying out welding, flame-cutting and grinding operations, clean the machine and its surroundings from dust and other inflammable substances and make sure that the premises are adequately ventilated (risk of explosion).

When handling oil, grease or other chemical substances, observe the product-related safety regulations (see safety specifications).

Be careful when handling hot consumables (risk of burning or scalding).

Transporting and recommissioning The machine must be loaded and transported only in accordance with the operating instructions.

Use only appropriate means of transport and lifting gear of adequate capacity.

The recommisioning procedure must be strictly in accordance with the operating instructions.

Hydraulic equipment Check all lines, hoses and screwed connections regularly for leaks and obvious damage. Repair damage immediately. Splashed oil may cause injury and fire.

Depressurize all system sections and pressure pipes to be removed in accordance with the specific instructions for the unit concerned before carrying out any repair work.

Hydraulic lines must be laid and fitted properly.

Ensure that no connections are interchanged. The fittings, lengths and quality of the hoses must comply with the technical requirements.

BA RH170B(3 725 013.00)-EN

1-11

OPERATING INSTRUCTIONS RH170B Electric Introduction ACCIDENT PREVENTION REGULATIONS FOR ELECTRICALLY POWERED EXCAVATORS The safety and accident-prevention regulations valid in the respective country must be observed.

The following requirements are based on extracts from the German accident prevention regulations "Electrical Systems and Equipment (BGVA 3, former VBG 4)".

The installation, modification and repair of the electromechanical component of electrical systems and components must be delegated only to qualified electricians or firms employing such experts.

A "qualified electrician" in the context of this regulation is a person who, on the basis of specialized training, know-how and experience as well as knowledge of the relevant regulations, is in a position to judge the extent of the work assigned to him and to recognize any potential hazards.

The machine owner/contractor must inform all persons working on electrical installations and components or in the vicinity of components conducting electricity during operation, or who are responsible for the operation of electrical systems, of the potential danger of electricity and must instruct them on the accident prevention regulations relevant to their work. Instruction in safety measures is to be repeated at intervals appropriate to the operating conditions. If necessary, special working regulations must be displayed.

The excavator and its electrical systems must be adequately protected against other potential hazards of electricity, e.g. fire and explosion.

Electrical systems and components must be protected against electric shock in the case of a fault, e.g. short circuit to exposed conductive part.

Any parts of the electrical system conducting current when in operation must be housed in lock-up switchgear cabinets. Hazard warning signs are displayed on these lock-up cabinets.

VOLTAGE HAZARD The switchgear cabinets must be secured against unauthorized opening. The key must be kept by the electrician in charge.

Electrical systems and components must not be used unless they comply with the operational and local safety requirements. They must be in an orderly state and must be kept in such a state.

Any defects or malfunctions occurring in electrical systems or components must be reported to the electrician in charge.

Before switching on any systems, the excavator operator must check that no one is working on the machine or its electrical systems.

The heavy-duty power cable must never be driven over, buried or ripped away. The excavator equipment must never be set down on the power cable.

When the excavator is being moved, the cable must never be pulled or dragged over the ground.

Whenever work is being carried out on electrically powered excavators, the general rules of engineering - especially those concerning low and medium voltage - must be observed. Regulations such as those issued by the German VDE, e.g. specification VDE 0100, should be observed.

Observe all relevant laws and provisions in your country.

Before commencing any work on electrical systems and components, the electrician in charge (or an electrician appointed by him) must switch the power off all circuits and lock them in the OFF state as follows:  Switch voltage OFF all systems.  Check with voltage detectors that all systems are voltage-free.  Lock switches/systems to prevent them from being switched ON. The above procedures must be carried out in the given sequence.

1-12

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Introduction The machine contractor must provide all the necessary protective equipment and adopt the necessary safety procedures. He must ensure that the safety equipment is used and the safety procedures observed.

The excavator operator and all personnel working on the excavator must use the protective equipment and carry out the specified safety procedures.

It is absolutely forbidden to work on any systems or components while they are conducting current.

Fatal injury can occur.

If work has to be done in special cases on systems or components conducting current, appropriate safety measures must be taken. Work must not be done on "live" systems and components except by the electrician in charge. The machine contractor must also be notified.

The excavator and its electrical systems must not be switched on again until the above safety procedures have been cancelled and all working areas are prepared for the resumption of operations.

Start-up can be ordered only by the person in charge (qualified electrician). Time-based switchon agreements are absolutely forbidden.

Safety instructions for excavators with electric motor Before carrying out any maintenance and repair work on the electrical system, the following precautions must be taken:

In the transformer station  Switch off the supply voltage.  Lock the safety device preventing switch-on; apply a warning sign.  Check that the electrical system is off circuit and dead.  Connect to earth and short-circuit.  Protect adjacent and live parts against accidental contact.

On the excavator  Switch off the switch-disconnector.  Lock the safety device preventing switch-on; apply a warning sign.  Remove the cover.  Check that the electrical system is off circuit and dead.  Connect to earth and short-circuit.  Slide the partition into the disconnector housing.

BA RH170B(3 725 013.00)-EN

1-13

OPERATING INSTRUCTIONS RH170B Electric Introduction FIRE AND EXPLOSION HAZARD Safety instructions

Place suitable fire guardings (fire barriers) if open fire or flying sparks cannot be avoided during repair work.

Prior to commencing work, obtain information on the national and corporate rules for the prevention of accidents.

Apply special protection to cables, cable ducts as well as to hose and pipe lines.

Pay particular attention to hazards caused by combustible and easily flammable substances.on the safe handling of the fire extinguishers to be used.

Ensure sufficient ventilation.

Avoid smoking and open fire on, next to and below the excavator.

Combustible and easily flammable substances or liquids increase the fire and explosion hazard.

Do not store or handle any flammable substances during operation.

Clean the excavator thoroughly, if possible, with a steam jet (rubber parts and electric components with compressed air - refer to information label), when, for example, oil, grease, solvent or cleaner was spilled.

Such substances may spontaneously ignite if they get into the vicinity of hot units or objects.

Even battery gases can ignite in open flames or fire.

If necessary, also cover the ground with fireprotective blankets.

Clean the excavator before starting a job.

Do not keep any fire extinguishers that are not suitable or have not been tested.

Do not extinguish flammable liquids with water.

Use:  dry-powder, 

carbon-dioxide or



foam extinguishing compounds.

When getting into contact with burning substances, the fire-fighting water would abruptly evaporate and distribute the substance such as burning oil over a wide area. Water causes short-circuits in the electrical system thus possibly entailing new hazards.

DANGER TO LIFE Call the fire brigade.

Have all your welding, flame cutting and grinding work approved.

Avoid parking the excavator in places where  combustible substances such as coal dust or tar are present. 

open or smouldering fire may occur.

Remove the excavator from such an area where combustible or easily flammable liquids have spilled from the excavator onto the ground.

Flying sparks (caused by welding, flame cutting, grinding, electrical short-circuit) may cause fire on the ground that can spread to the excavator.

1-14

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Introduction NOTES ................................................................................................................................................................... ................................................................................................................................................................... ................................................................................................................................................................... ................................................................................................................................................................... ................................................................................................................................................................... ................................................................................................................................................................... ................................................................................................................................................................... ................................................................................................................................................................... ................................................................................................................................................................... ................................................................................................................................................................... ................................................................................................................................................................... ................................................................................................................................................................... ................................................................................................................................................................... ................................................................................................................................................................... ................................................................................................................................................................... ................................................................................................................................................................... ................................................................................................................................................................... ................................................................................................................................................................... ................................................................................................................................................................... ................................................................................................................................................................... ................................................................................................................................................................... ................................................................................................................................................................... ................................................................................................................................................................... ................................................................................................................................................................... ................................................................................................................................................................... ................................................................................................................................................................... ................................................................................................................................................................... ................................................................................................................................................................... ...................................................................................................................................................................

BA RH170B(3 725 013.00)-EN

1-15

OPERATING INSTRUCTIONS RH170B Electric Introduction

1-16

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Operation 2 OPERATION Operating instructions

Target group

Part 1 INTRODUCTION FUNDAMENTAL SAFETY INSTRUCTIONS

Operating personnel + Inspection and servicing personnel + Repair personnel

Part 2 OPERATION

Operating personnel The operating personnel must have knowhow relevant to the operation and the application of this or comparable machines.

Part 3 INSPECTION AND SERVICING Part 4 REPAIR WORK

Inspection and servicing personnel The inspection and servicing personnel must have know-how relevant to the inspection and servicing of this or comparable machines.

Repair personnel The repair personnel must have know-how and experience relevant to the repair of this or comparable machines.

Part 5 ANNEX

Part 6 INDEX

BA RH170B(3 725 013.00)-EN

Operating personnel + Inspection and servicing personnel + Repair personnel Operating personnel + Inspection and servicing personnel + Repair personnel

2-1

OPERATING INSTRUCTIONS RH170B Electric Operation

2-2

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Operation OPERATION - SAFETY INSTRUCTIONS Operating instructions Never operate the machine before having read and understood the operating instructions.

Safety belt For machines with a safety belt for operating personnel: Check the safety belt attached to the driver's seat.

In the event of damage or after an accident, have it replaced immediately.

Apply the safety belt before starting work.

State of the machine Pay special attention to the "Fundamental Safety Instructions" and to all warning and instruction signs attached to the machine.

Familiarize yourself with the layout, the functioning and the sense of actuation of the control elements prior to starting up the machine.

Activate the control elements from the driver's seat only.

Operate the machine only in a safe state and only in accordance with its designated use. Always observe the safety instructions.

Always have inspection and maintenance work carried out on schedule.

Operate the machine only with the equipment and component combinations approved by Bucyrus HEX. Clear-cut data are given in the technical specification.

Keep the operating instructions with the machine at all times.

Never install and commission other equipment and component combinations without Bucyrus HEX having first inspected and approved the project.

Operating personnel

Before starting work or travelling with the machine, check that the braking, signalling and lighting systems are fully functional.

The operating personnel must be fully informed of the operation and application of this or comparable machines.

The necessary know-how can be acquired in several days' instruction, e.g. by an Bucyrus HEX mechanic or by attending an Bucyrus HEX operator's training course.

Personal protective gear and working clothing

Poor visibility may result in accidents. Always clean the windows and the glass covers of all lamps before starting the machine.

Check that all warning and instruction signs attached to the machine are present and legible.

Entering and leaving the machine Always face the machine when entering or leaving it.

Wear a safety helmet and working footwear with non-slip soles. Smooth soles may slip from steps and pedals resulting in injury or incorrect operation.

Use only the ladders, steps, platforms and grab handles provided when entering and leaving the machine.

Wear closely fitting working clothing when operating the machine. Loose, wide garments may result in control levers being inadvertently activated

Always keep ladders, steps and platforms in a non-slip, safe state and remove any oil, grease, soil, snow, ice and other foreign matter immediately.

BA RH170B(3 725 013.00)-EN

2-3

OPERATING INSTRUCTIONS RH170B Electric Operation Hazard range The hazard range is that zone around the machine in which persons are within reach of loads or attachments falling as a result of operational movements by the machine, of its equipment and attachments or of swinging loads.

Operating Instructions, where to store it in the driver’s cab One copy of the Operating Instructions for the machine must be available in the driver’s cab during operation.

The binder with the Operators Instructions can be stored in the tray (Fig. 2-1:).

Persons within the hazard zone Always use the horn to warn persons in the immediate vicinity of the machine before starting up the machine.

Ensure that no one sets foot in the hazard zone of the machine. Interrupt work until such persons have left the hazard zone.

Marshallers The marshaller must keep outside the hazard zone.

Have a marshaller to assist you:  when you have no clear overview over the hazard zone of the machine, 

when reversing,



when shunting.

Fig. 2-1:

Use only those communication signals which you and the marshaller understand, or use aids for communication (e.g. walkie-talkie/camera).

Calls cannot be understood by the marshaller because of the noise made by the machine during operation.

Keep in constant contact with the marshaller.

Stop the machine immediately if you lose contact with the marshaller.

Securing the machine Secure the machine as described under "Securing the machine" before:  mounting or dismantling the attachment, 

parking the machine after daily operation,



carrying out any servicing or repair work.

2-4

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Operation FIRE AND EXPLOSION HAZARD Safety instructions

Place suitable fire guardings (fire barriers) if open fire or flying sparks cannot be avoided during repair work.

Prior to commencing work, obtain information on the national and corporate rules for the prevention of accidents.

Apply special protection to cables, cable ducts as well as to hose and pipe lines.

Pay particular attention to hazards caused by combustible and easily flammable substances.on the safe handling of the fire extinguishers to be used.

Ensure sufficient ventilation.

Avoid smoking and open fire on, next to and below the excavator.

Combustible and easily flammable substances or liquids increase the fire and explosion hazard.

Do not store or handle any flammable substances during operation.

Clean the excavator thoroughly, if possible, with a steam jet (rubber parts and electric components with compressed air - refer to information label), when, for example, oil, grease, solvent or cleaner was spilled.

Such substances may spontaneously ignite if they get into the vicinity of hot units or objects.

Even battery gases can ignite in open flames or fire.

If necessary, also cover the ground with fireprotective blankets.

Clean the excavator before starting a job.

Do not keep any fire extinguishers that are not suitable or have not been tested.

Do not extinguish flammable liquids with water.

Use:  dry-powder, 

carbon-dioxide or



foam extinguishing compounds.

When getting into contact with burning substances, the fire-fighting water would abruptly evaporate and distribute the substance such as burning oil over a wide area. Water causes short-circuits in the electrical system thus possibly entailing new hazards.

DANGER TO LIFE Call the fire brigade.

Have all your welding, flame cutting and grinding work approved.

Avoid parking the excavator in places where  combustible substances such as coal dust or tar are present. 

open or smouldering fire may occur.

Remove the excavator from such an area where combustible or easily flammable liquids have spilled from the excavator onto the ground.

Flying sparks (caused by welding, flame cutting, grinding, electrical short-circuit) may cause fire on the ground that can spread to the excavator.

BA RH170B(3 725 013.00)-EN

2-5

OPERATING INSTRUCTIONS RH170B Electric Operation DESCRIPTION OF THE EXCAVATOR

Fig. 2-2:

2-6

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Operation Excavator layout see Fig. 2-2:

Undercarriage 1 - Track drive 2 - Idler 3 - Track roller 4 - Support roller 5 - Crawler track 6 - Track tensioner 7 - Slewing ring 8 – Emergency Ladder 9 - Slip ring assembly 10 - Cable guide for drag cable

Superstructure 11 - Elektric motor 12 - Switchgear cabinets (DER I and II, medium voltage, circuit breaker) 13 - Switchgear cabinet 14 – Electric motor connection box 15 - Switchgear cabinet and battery charger 16 – Switchgear cabinet power factor correction 17 - Hydraulic oil reservoir 18 - Hydraulic oil cooler 20 - Pump transfer gearbox 21 - Working pump

35 - Fire-extinguisher 36 - Batteries 37 - Control-cabinet with CMS 38 - Control-cabinet (24 V) with battery main switch 39 – On-board crane (optional) 40 – Power station for on-board-crane 41 - Service station (tanklift) 44 - Grease container of central lubricating system 46 – Hydraulic ladder 47 - Ladder 49 – Counterweight 50 – Tool cabinet (optional)

Loading bucket 51 - Boom 52 - TriPower linkage 53 - Stick 54 - Bottom-dump bucket 55 - Boom cylinder 56 - Stick cylinder 57 - Tipping cylinder 58 - Bottom-dump cylinder 64 - Control valves 65 - Quick-action valve

22 - Cooling oil pump 23 - Servo system pump 24 - Gearbox circulating pump 25 – Fan drive (hydraulic oil cooler) 27 - Slewing pump 28 – Filling pump (slewing circuit) 29 - Slewing gear 30 - Travel block and rotor 31 - Driver's cab 32 - Control stand with BCS 34 - Air conditioner under roof

BA RH170B(3 725 013.00)-EN

2-7

OPERATING INSTRUCTIONS RH170B Electric Operation Undercarriage

Stored Program Control (SPC)

The undercarriage of the hydraulic excavator serves as a stable base and for travelling. The crawler tracks are driven hydraulically with oil motors and travel gearboxes. Undercarriage and superstructure are connected by means of a slewing ring.

The SPC controls the functions:  Switch on electric motor,

Superstructure

Further information is given in the Technical Handbook “Stored-program control”.

The superstructure accommodates the drive and part of the hydraulic and electrical equipment.

Drive



Switch off electric motor Stop,



Central lubricating system,



Further auxiliary functions.

Control Management System (CMS)

The drive unit comprises electric motor, pump transfer gearboxes, hydraulic pumps, hydraulic cylinders and hydraulic motors.

The CMS is an electrohydraulic servocontrol. Together with the PMS, it provides for optimum interaction between drive hydraulic circuit and working movements.

Hydraulic system

The required working movements are recognized by microcontroller-assisted scanning of the operating elements (hand levers, pedals) and transmitted to electrohydraulic valves.

All working and travelling movements are performed hydraulically. The movements are controlled by servovalves. The working commands are initiated by hand and transmitted to the valves via control circuits. The oil supply from the superstructure to the undercarriage is ensured by the rotor.

The hydraulic system is overload-protected by pressure-relief valves. The hydraulic pumps are supplied with oil from a hydraulic reservoir.

In the system sequence, the drive regulation is first activated to provide hydraulic working energy. Only then are working movements enabled.

Further information is given in the Technical Handbook.

Pump Managing System (PMS) The Pump Managing System (PMS) with overlimit regulation ensures optimum utilization of the installed or preset engine power. The electronic pump demand control prevents the machine from demanding more hydraulic power than the electric motor can furnish. A microprocessor ensures that the hydraulic output power of the pump is optimally suited to the actual operation conditions.

The PMS box (load-limit regulator) is installed in a control cabinet in the driver's cab.

2-8

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Operation Demand control / Zero-flow regulation In the fine-control range, swivelling of the hydraulic pumps, and thus the variation of oil flow, are proportional to control lever and pedal valve travel.

This means that during the work, the pumps supply only as much hydraulic oil as required to perform the working movement. In the neutral position of the control levers, the pumps are automatically swivelled to zeroflow.

These special features offer the following advantages:  minimum power losses, 

reduced temperature of the hydraulic oil and



greater service life of hydraulic pumps and electric motor.

BA RH170B(3 725 013.00)-EN

Board-Control-System (BCS) The BCS is a data-evaluating and data-processing system whose function is to collect, evaluate and store data about the excavator's operating status and to display these to the operator.

The BCS is based on a micro-processor. The measured values (actual values) supplied by sensors and transducers installed in the excavator are compared to preset nominal values. Out-of-limit conditions are displayed in the form of error messages in the cab.

Critical operating conditions are additionally indicated by optical and acoustic warning signals.

Further dedails are set out in the Board-ControlSystem operating instructions.

Electrical system Supply voltage (medium voltage)

7200 V 60 Hz

Control voltage (low voltage)

400/230 V

Lighting voltage

24 V

Emergency voltage

24 V

Control voltage

24 V

2-9

OPERATING INSTRUCTIONS RH170B Electric Operation Power supply The electric power is supplied to the excavator through the drag cable (1, Fig. 2-3:) and connection box (3).

The drag cable is guided by a cable guide (2).

The power is then transmitted via the slip ring assembly (4) to the circuit breaker in the switchgear cabinet (Fig. 2-4:).

The drag cable can be wound on a cable reel (optional).

Fig. 2-3:

Fig. 2-4:

2-10

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Operation Signs Warning and instruction signs Observe the warning and instruction signs attached to the machine.

Keep the signs legible and clean.

Replace signs immediately if they have become illegible.

New warning and instruction signs can be ordered from the Bucyrus HEX Spare Parts Service. The ordering part numbers are set out in the spareparts list of the machine.

Fig. 2-5: up to Fig. 2-15: show the location of warning and instruction signs on the machine.

BA RH170B(3 725 013.00)-EN

2-11

OPERATING INSTRUCTIONS RH170B Electric Operation

Fig. 2-5:

2-12

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Operation

Fig. 2-6:

BA RH170B(3 725 013.00)-EN

2-13

OPERATING INSTRUCTIONS RH170B Electric Operation

Fig. 2-7:

2-14

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Operation

Fig. 2-8:

BA RH170B(3 725 013.00)-EN

2-15

OPERATING INSTRUCTIONS RH170B Electric Operation

Fig. 2-9:

2-16

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Operation

Fig. 2-10:

BA RH170B(3 725 013.00)-EN

2-17

OPERATING INSTRUCTIONS RH170B Electric Operation

Fig. 2-11:

2-18

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Operation

Fig. 2-12:

BA RH170B(3 725 013.00)-EN

2-19

OPERATING INSTRUCTIONS RH170B Electric Operation

Fig. 2-13:

2-20

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Operation

Fig. 2-14:

BA RH170B(3 725 013.00)-EN

2-21

OPERATING INSTRUCTIONS RH170B Electric Operation

Fig. 2-15:

2-22

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Operation

Machine number The identification plate (Fig. 2-17:) with the machine number is attached to the front side of the Aframe (arrow, Fig. 2-16:).

Fig. 2-17:

Electric motor number Fig. 2-16:

The serial number plate (1, Fig. 2-18:) for the electric motor is located on the electric motor.

Fig. 2-18:

Component numbers Other larger units also have identification plates indicating, among other things, their serial number.

On steel components, the Bucyrus HEX part number or the serial number may be stamped into the metal at a clearly visible place.

BA RH170B(3 725 013.00)-EN

2-23

OPERATING INSTRUCTIONS RH170B Electric Operation Entering and leaving the machine, Safety instructions Risk of injury due to slipping.

Clean off oil, grease, soil, mud, snow, ice and other substances from footwear, grab handles, ladders and steps.

Keep ladders, steps, platforms and grab handles in a non-slippery condition.

For entering and leaving use only the ladders, steps, platforms and grab handles provided (cf. illustration in Fig. 2-19:).

Access lighting The access can be illuminated in the dark. The access lighting is switched on:  When you stand beside the excavator: By a pull switch (2, Fig. 2-20:) operated with a string from the ground. The lighting system switch is located under the counterweight.  When you are in the cab: With switch (5, Fig. 2-21:).

The access lighting is activated for three minutes and then switched off automatically.

Always face the machine when entering or leaving it.

Fig. 2-20:

Fig. 2-19:

Fig. 2-21:

2-24

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Operation Swinging ladder Raising resp. lowering the swinging ladder (Fig. 2-22:).

Lowering the swinging ladder (from the upper carriage)  Start electric motor.  Push lever (1, Fig. 2-23:) on control valve (2) downwards to position “ II “.

The swinging ladder is lowered (Fig. 2-22:).

The swinging ladder can also be lowered when the electric motor ist stopped.

Fig. 2-22:

Raising the swinging ladder (from the upper carriage)  Start electric motor.  Pull lever (1, , Fig. 2-23:) on control valve (2) upwards to position “ I “.

The swinging ladder is raised (Fig. 2-24:).

Fig. 2-24:

Lowering the swinging ladder (from the bottom)  Pull down rope (3, Fig. 2-25:).

The swinging ladder is lowered (Fig. 2-22:).

Fig. 2-23:

The upper carriage can only be swung when the folding ladder is raised completely (Fig. 2-24:).

BA RH170B(3 725 013.00)-EN

Fig. 2-25:

2-25

OPERATING INSTRUCTIONS RH170B Electric Operation Folding ladder (optional) Raising resp. lowering the folding ladder (Fig. 2-26:).

Lowering the folding ladder (from the upper carriage)  Start electric motor.  Push lever (1, Fig. 2-27:) on control valve (2) downwards to position “ II “.

The folding ladder is lowered (Fig. 2-26:).

The folding ladder can also be lowered when the electric motor is stopped.

Fig. 2-26:

Raising the folding ladder (from the upper carriage)  Start electric motor.  Pull lever (1, Fig. 2-27:) on control valve (2) upwards to position “ I “.

The folding ladder is raised (Fig. 2-28:).

Fig. 2-28:

Lowering the folding ladder (from the bottom)  Pull down rope (3, Fig. 2-29:).

The folding ladder is lowered (Fig. 2-26:).

Fig. 2-27:

The upper carriage can only be swung when the folding ladder is raised completely (Fig. 2-28:).

2-26

Fig. 2-29:

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Operation Escape ladder (optional) The escape ladder (arrow, Fig. 2-30:) is located beside the driver´s cab.

Function of ladder locking as well as free movement of the ladder must be regularly checked accordiing to the maintenance plans.  Kick down locking lever (2, Fig. 2-31:). The escape ladder is now unlocked and moves down quickly to the ground.  Swing barrier (1, Fig. 2-31:) to the right and use the ladder to escape downwards.

Fig. 2-30:

Fig. 2-31:

BA RH170B(3 725 013.00)-EN

2-27

OPERATING INSTRUCTIONS RH170B Electric Operation Cab interior lamp The interior lamp is switched on and off with switch (Fig. 2-32:).

Switch position 0 - lamp off, 1 - lamp on.

The interior lamp is also switched on and off with switches (arrow, Fig. 2-33:) and / or (96, Fig. 2-34:).

The interior lamp can be used even if the electrical system is switched off.

Therefore, switch off the interior lamp when leaving the machine. The batteries may be discharged if the interior lamp is left on for prolonged periods.

Fig. 2-32:

Fig. 2-33:

Fig. 2-34:

2-28

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Operation Servicing lighting

Illuminating the control column

Switch on the lamps in the modules with switches (95, Fig. 2-35: and arrow, Fig. 2-36:).

The control column front could be illuminated with a lamp (30, Fig. 2-37:).

Switch (95, Fig. 2-36:) is located in the control column in the driver's cab.

Turn lamp head from "0" to "I" to switch the lamp on.

Switch (arrow, Fig. 2-36:) is located beside the cab door.

There are also switches build in the modules.

Fig. 2-37:

Fig. 2-35:

Fig. 2-36:

BA RH170B(3 725 013.00)-EN

2-29

OPERATING INSTRUCTIONS RH170B Electric Operation EMERGENCY STOP switch The entire electrical system beginning at the output side of the circuit breaker switch is switched off by the EMERGENCY STOP switches. The electric motor wil be shut off.

Medium voltage 7.2 kV is still alive at the input side of the circuit breaker switch (in control column medium voltage 7.2 kV).

To switch off the whole machine from any electric power, electric power must be switched off at the power supply station where the supply cable is connected.

Fig. 2-38:

The battery voltage of 24V still remain, it can be switched off with the key operated switch in the control column or with the battery main switch (see "Electrical system (24V) switching on / off" and "Battery main switch").

In an emergency, actuate one of the EMERGENCY STOP switches.

The EMERGENCY STOP switches are located  in the control column in the driver's cab (31, Fig. 2-38:), 

in the front of the 400V control cabinet in the counterweight (3, Fig. 2-39:),



near the service lift (6, Fig. 2-40:). The pull switch is is operated by a string (5).

The electrical system can be switched on after the EMERGENCY STOP switches are activated, to do so, pull out switches (Pull switch shown in Fig. 2-40: must be pushed in).

Fig. 2-39:

Fig. 2-40:

2-30

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Operation Servicing switch

Windscreen washer

Before starting live-line servicing work e.g. measuring and testing with voltage applied, press switch (4, Fig. 2-41:) and secure it with a padlock.

The reservoir of the windscreen washing system (1, Fig. 2-42:) is installed in the cab module. For the reservoir capacity refer to the "Refilling quantities Other" table.

Pressing the switch transmits a signal to the PLC. The electric motor can not be switched on.

Fig. 2-42:

Fig. 2-41:

BA RH170B(3 725 013.00)-EN

2-31

OPERATING INSTRUCTIONS RH170B Electric Operation Driver's seat The driver's seat (Fig. 2-43: and Fig. 2-44:) can be adjusted in several positions.

Never adjust the seat while driving.

Concentrate on the road to avoid accidents.

Before carrying out any seat adjustments stop the machine and set the control levers to "0"

Fig. 2-43:

2-32

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Operation

Fig. 2-44:

BA RH170B(3 725 013.00)-EN

2-33

OPERATING INSTRUCTIONS RH170B Electric Operation Fire extinguisher

Handling

The excavator is equipped with two four extinguishers. The conventional one is located near the drivers cab (Fig. 2-45:), the carbon dioxide fire extinguishers are located near the electric motor and switching cabinets.

Fig. 2-46:

 Pull out securing pin (2, Fig. 2-46:).  Strike knob (3) hard, then release again.

Fig. 2-45:

 Operate the extinguishing gun.

The excavator driver and the maintenance personnel must informthemselves about how to handle the fire-extinguisher in order to be able to act fast and efficiently in case of beginning fires. Such instruction should be given by a qualified instructor.

After fire-fighting, the extinguisher must be refilled Immediately and prepared ready for use.

Extinguishing agent

Have the extinguisher inspected at regular intervals by an expert. This is required by local authorities and insurance companies and is in the interest of your own safety.

The conventional fire-extinguisher is filled with 12 kg (26.4lb) Glutex. This extinguishing agent is used for fighting fires of classes A, B and C. Fires are extinguished fast, perfectly and without residues.

The carbon dioxide fire extinguishers are intended for fighting fires of electrical parts.

2-34

Inspection

Have the fire-extinguisher checked at the prescribed intervals by authorized testing agencies.

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Operation Automatic fire-extinguishing system (optional) The automatic fire-extinguishing system prevents fire from spreading.

It is, however, assumed that the machine is thoroughly cleaned of combustible and easily flammable substances.

The excavator operator and the maintenance personnel must familiarize themselves with the automatic fire-extinguishing system.

Such instruction should be given by a qualified instructor.

The fire-extinguishing system is activated automatically in an emergency.

Trainer's / instructor's seat For driver training / instructing purposes it is often required that a trainer / instructor accompanies the driver in the cab.

For the safety of the trainer / instructor during excavator operation the cab is equipped with a second seat. This seat is installed behind the driver's seat (arrow, Fig. 2-47:).  Sit down on this seat and do not forget to fasten the seat-belt (if installed).  Do not leave this seat during the training / instruction session and /or as long as the machine is in operation.

Individual extinguishing circuits can be activated manually.

Inspection Have the extinguishing system inspected regularly by an expert. This is required by authorities and insurance companies and is in the interest of your own safety.

Fig. 2-47:

BA RH170B(3 725 013.00)-EN

2-35

OPERATING INSTRUCTIONS RH170B Electric Operation Emergency escape device (optional) Elements of the harness (Fig. 2-48:- Fig. 2-50:) Pos. Designation Back support 1 Shoulder belt 2 Shoulder belt 3 Loop (chest belt) 4 Loop (chest belt) 5 Loop (back support) 6 11 Holding device 12 Fall arrester 13 Guidance line 14 Hanging up line 15 Handbag with harness 16 Snap hook 17 Hook safety device

Fig. 2-49:

Fig. 2-50:

See Description of the supplier.

Fig. 2-48:

Important hints Before using operator shall have received adequate training.

The harness must be used by one person only.

He is responsible for the appropriate use and maintenance.

Visual inspection is recommended prior to each use; if necessary it must be checked by an expert.

Harness must be checked annualy (every 12 month) by an expert.

2-36

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Operation Taking on harness  Take harness out of handbag (15, Fig. 2-51:).

 Pull loop (6) of the back support (1) between your legs to the front (Fig. 2-53:).  Pull loop (5, Fig. 2-54:) through loop (6).

Fig. 2-51:

 Take on shoulder belts (2 and 3, Fig. 2-52:).

Fig. 2-54:

 Pull loop (4, Fig. 2-54:) through loop (5).  Press the hooking safety device (17, Fig. 2-54:) of the snap hook (16).

Fig. 2-52:

 Pull back support (1, Fig. 2-52:) behind your body (Fig. 2-53:). The loops (4 and 5) are in front of your body.

Fig. 2-55:

Fig. 2-53:

BA RH170B(3 725 013.00)-EN

2-37

OPERATING INSTRUCTIONS RH170B Electric Operation  Hang up loop (4, Fig. Fig. 2-56:) into snap hook (16).

Fig. 2-56:

If you have the harness put on in such a way in case of danger you can escape from the excavator (Fig. Fig. 2-58:).

Fig. 2-58:

 Release hooking safety device (17, Fig. 2-57:).

Fig. 2-57:

2-38

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Operation

BA RH170B(3 725 013.00)-EN

2-39

OPERATING INSTRUCTIONS RH170B Electric Operation MONITORING, WARNING AND CONTROL ELEMENTS

Fig. 2-59:

2-40

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Operation (Fig. 2-59:) No.

Element

Function

1

BCS

Electronic measuring-data collection and processing system

Board Control System, acquisition and display of important operating data of the excavator.

2

Monitor

BCS

Displays the data collected.

Gives warnings and provides help, if desired.

3

UP button

Selects the BCS program; Positions the Cursor.

4

DOWN button

Selects the BCS program; Positions the Cursor.

5

ENTER button

Confirms a program; Activates a desired program.

6

BACK button

Recalls the Service Menu.

7

HOLD button

Freezes actual service data.

8

Print button

Recalls the Print Menu.

9

SERV. button

Recalls the Service Menu.

10

HELP button

Recalls the Help Menu.

11

BL + button

Adjusts BCS monitor background lighting brighter.

12

BL - button

Adjusts BCS monitor background lighting darker.

BA RH170B(3 725 013.00)-EN

Symbol

2-41

OPERATING INSTRUCTIONS RH170B Electric Operation

Fig. 2-60

2-42

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Operation (Fig. 2-60) No.

Element

Function

30

Lamp

Illuminates the front side of the control column.

31

Pushswitch

Emergency OFF

Symbol

The entire electrical system is interrupted in all poles by the on-board circuit breaker.

Even after actuation of the EMERGENCY STOP switch, medium voltage (7.2 KV) is present (primarily) from the transformer station via drag cable and slip ring assembly to the circuit breaker.

32

Key-switch

Switches the low voltage system on and off.

33

Buzzer

Gives an acoustic warning signal if a fault is reported: 

Electric motor – winding temperature too high – bearing temperature too high



bord transformer temperature too high



Hydraulic oil level too low



Distributor gearbox temperature too high



Swing pump temperature (1 and / or 2; too high



Swing gearbox temperature (1 and / or 2) too high



Fault in lubricating system

Lower the equipment to the ground and switch off electric motor immediately if the buzzer (33) sounds and the BCS indicates a fault. The buzzer (33) continues to sound until the fault has been retified.

BA RH170B(3 725 013.00)-EN

2-43

OPERATING INSTRUCTIONS RH170B Electric Operation

Fig. 2-61:

2-44

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Operation (Fig. 2-61:) No.

Element

Function

33

Buzzer (continued)

Gives an acoustic warning signal if a fault is reported: 

Distributor gearbox contaminated



Working pump (1, 2, 3, and / or 4; left and / or right) contaminated



Swing motor (1 and / or 2) contaminated



Swing circuit temperature (1 and / or 2) too high



Lubricating system pressure too low



Grease level in lubricating system too low



On-board voltage 24 V too low

Symbol

The buzzer (33) continues to sound until the fault has been retified.

34

Buzzer

Gives an acoutic warning signal when the stick/boom angle to too small.

35

Terminals

For electronic machine diagnostics.

36

Antenna (Optional)

37

Radio (Optional)

BA RH170B(3 725 013.00)-EN

2-45

OPERATING INSTRUCTIONS RH170B Electric Operation

Fig. 2-62:

2-46

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Operation (Fig. 2-62:) No.

Element

Function

41

Indicator lamp

Medium voltage

Lamp is lit up when the circuit breaker is switched on. Medium voltage 7.2 kV applied.

42

Indicator lamp

Rotary field monitoring

Lamp is lit up when the rotary field (phasing) is correct.

51

Button

Electric motor ON

Switches on the electric motor.

52

Button

Electric motor OFF

Switches off the electric motor.

BA RH170B(3 725 013.00)-EN

Symbol

2-47

OPERATING INSTRUCTIONS RH170B Electric Operation

Fig. 2-63:

2-48

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Operation (Fig. 2-63:) No.

Element

Function

71

Switch

Travel motors

Switches on the fast gear (overdrive).

72

Switch

Undercarriage holding brake

CCW: brake permanently applied The excavator can not be driven CW:

Symbol

Every time the excavator stops, the undercarriage brake is automatically applied after approx. 8 sec.

The undercarriage brake is automatically released when the travel function is activated.

Actuate switch only when the excavator is stationary. Do not use as service brake.

Activate after a fault in the central lubricating system.

73

Taster

Reset

74

Switch

Electronic excavator Switches on the electronic servo control. control

75

Switch

Not connected.

76

Cigarette lighter

77

Switch

BA RH170B(3 725 013.00)-EN

Not connected.

2-49

OPERATING INSTRUCTIONS RH170B Electric Operation

Fig. 2-64:

2-50

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Operation (Fig. 2-64:) No.

Element

Function

81

Switch

Not connected.

82

Switch

Superstructure holding brake

Symbol

Blocks the superstructure.

Actuate switch only when the excavator is stationary.

Do not use as service brake.

83

Switch

Windscreen wiper

Activates permanent / intermittent wiping.

84

Switch

Screen washer

Activates the wipe / wash function.

85

Switch

Floodlamps

Switches on the floodlamps on the driver´s cab.

86

Switch

Floodlamps

Switches on the floodlamps on the driver´s cab roof.

87

Switch

Floodlamps

Switches on the floodlamps on the hydraulic oil cooler.

88

Switch

Floodlamps

Switches on the floodlamps on the counterweight.

BA RH170B(3 725 013.00)-EN

2-51

OPERATING INSTRUCTIONS RH170B Electric Operation

Fig. 2-65:

2-52

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Operation (Fig. 2-65:) No.

Element

Function

Symbol

91

Switch

Emergency Operati- Actuate and hold if boom and stick must be lowered in an emergency. on Boom/Stick

92

Button

Dumper count

93

Switch

Activates boom cylinder limit switch (optional)

94

Button

When switched it is possible to swing the uppercarriage and to drive the excavator even when the hydraulic ladder or the service station is in the lower position.

RESET of counter.

Risk of damaging the ladder or the service station!

Be careful and swing the uppercarriage and drive the excavator very slowly and only a short way.

95

Switch

Lighting

Switches on the lighting for servicing work.

96

Switch

Lighting

Switches the cab lighting on and off.

97

Switch

Windscreen wiper rear window (optional)

Activates permanent wiping.

98

Switch

Beacon (optional)

Switches the beacon on and off.

BA RH170B(3 725 013.00)-EN

2-53

OPERATING INSTRUCTIONS RH170B Electric Operation

Fig. 2-66:

2-54

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Operation (Fig. 2-66:) No.

Element

Function

101 Button

Dumper count

To the left – increment count To the right – decrement count

102 Button

Boom floating position (shovel equipment only)

If actuated: stick cylinders are pressurized when retracted.

Symbol

Actuate button (102) only when control lever (115) is in “0“ position.

103 Button

Boom floating position

If actuated: boom cylinders are pressurized when retracted.

Actuate button (103) only when control lever (116) is in “0“ position.

104 Button

Warning signal

Activates the horn.

105 Button inside seat Electronic excavator Switches the electronic excavator control on and off (inside the drivers seat). control ON – driver is sitting on the seat.

OFF – driver stands up.

111 Pedal

Bottom-dump bucket

Opens / closes the bottom-dump bucket.

112 Pedal

Travelling, left track

forwards / reverse

113 Pedal

Travelling, right track

forwards / reverse

115 Control lever

Lifts and lowers the bucket / backhoe bucket stick; Swings and brakes the superstructure.

116 Control lever

Raises and lowers the boom; Tipping and rearward tilting of bucket resp. backhoe bucket.

117 Button

Bottom-dump bucket

118 Button

By-pass for the automatically switch off for stickand /or backhoe cylinders (Option)

BA RH170B(3 725 013.00)-EN

To the left - opens the bottom-dump bucket.

To the right – closes the bottom-dump bucket.

To the left – automatically stopped stickand/or backhoe cylinders can be driven slowly to the limit stopps.

To the right – Not connected.

2-55

OPERATING INSTRUCTIONS RH170B Electric Operation

Fig. 2-67:

2-56

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Operation (Fig. 2-67:) (Options. Depending on the options ordered with the machine, the described elements can be found on different positions on the control column).

Symbol Function Selects the intensity level of the blower (3 levels).

Selects the desired control function (heating, cooling, ventilation, defrosting).

Sets the desired temperature inside the cab.

No.

Element

121

Rotary switch

Fan

122

Rotary switch

Mode

123

Knob

Thermostat

125

Control

Additional heating (optional equipment)

126

Momentary switch

Controlling the additional heating device via touch screen, see Back-up heating manufacturers manual.

Switches additional heating control OFF.

127

Momentary switch

Switches additional heating control ON.

128

Momentary switch

Not used on this machine.

129

Momentary switch

Not used on this machine.

130

Momentary switch

Reset fault monitoring.

140

Switch

Preheating system hydraulic oil

141

Switch

Preheating system pump drive

BA RH170B(3 725 013.00)-EN

Switches the preheating system for hydraulic oil ON and OFF. Monitoring lamp lits up when the system is switched ON. Switches the preheating system for the pump drive gearbox ON and OFF. Monitoring lamp lits up when the system is switched ON.

2-57

OPERATING INSTRUCTIONS RH170B Electric Operation

Fig. 2-68:

2-58

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Operation (Fig. 2-68:) (Options. Depending on the options ordered with the machine, the described elements can be found on different positions on the control column).

No.

Element

Function

151 Warning lamp

Slewing pump 1 contaminated

Lights up when the slewing pump is contaminated with metal particles.

152 Warning lamp

Slewing pump 2 contaminated

Lights up when the slewing pump is contaminated with metal particles.

153 Warning lamp

Slewing pump 3 contaminated

Lights up when the slewing pump is contaminated with metal particles.

154 Warning lamp

Slewing pump 4 contaminated

Lights up when the slewing pump is contaminated with metal particles.

155 Warning lamp

Main pump 1 contaminated

Lights up when the main pump is contaminated with metal particles.

156 Warning lamp

Main pump 2 contaminated

Lights up when the main pump is contaminated with metal particles.

157 Warning lamp

Distributor gearbox contaminated

Lights up when the distributor gearbox is contaminated with metal particles.

158 Warning lamp

Slewing pump 1 temperature

Lights up when the temperature in the slewing pump is too high

159 Warning lamp

Slewing pump 2 temperature

Lights up when the temperature in the slewing pump is too high

160 Warning lamp

Slewing pump 3 temperature

Lights up when the temperature in the slewing pump is too high

161 Warning lamp

Slewing pump 4 temperature

Lights up when the temperature in the slewing pump is too high

162 Warning lamp

Main pump 3 contaminated

Lights up when the main pump is contaminated with metal particles.

163 Warning lamp

Main pump 4 contaminated

Lights up when the main pump is contaminated with metal particles.

164 Warning lamp

Distributor gearbox contaminated

Lights up when the distributor gearbox is contaminated with metal particles.

BA RH170B(3 725 013.00)-EN

Symbol

2-59

OPERATING INSTRUCTIONS RH170B Electric Operation

Fig. 2-69:

2-60

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Operation (Fig. 2-69:) (Options. Depending on the options ordered with the machine, the described elements can be found on different positions on the control column).

No.

Element

Function

165 Warning lamp

Slewing motor 1 contaminated

Lights up when the slewing motor is contaminated with metal particles.

166 Warning lamp

Slewing motor 2 contaminated

Lights up when the slewing motor is contaminated with metal particles.

Symbol

free for optional

167 Warning lamp 168 Warning lamp

Hydraulic oil filter contaminated

Lights up when the flow resistance in the filter is too high. Replace filter elements if the warning lamp fails to go out when the oil is at operating temperature.

169 Warning lamp

Min. hydraulic oil level

Lights up when the hydraulic oil level in the hydraulic tank is too low.

170 Warning lamp

Electronic excavator Lights up when the electronic excavator control is switched on. control ON

171 Indicator light

Hydraulic oil tank

Lights up when one of the shut-off valves of the hydraulic oil tank is closed When the valve is closed, the electric motor cannot be started.

When a shutoff valve is closed with the electric motor running, the motor is stopped.

172 Thermometer

Hydraulic oil

BA RH170B(3 725 013.00)-EN

Indicates hydraulic oil temperature in hydraulic tank.

2-61

OPERATING INSTRUCTIONS RH170B Electric Operation PUTTING THE MACHINE INTO OPERATION Before daily start-up, carry out works in accordance with servicing plan T (cf. Part 3 "Inspection and servicing").

Prior to your dailiy start-up, make sure the machine has been cleaned of combustible and easily flammable substances.

Otherwise, increased fire and explosion hazard will exist.

Service station (tanklift) The excavator is equipped with a central service station (Fig. 2-70:The service station is attached to the frame and accessible from the ground below the uppercarriage. Express couplings are provided for refilling the following consumables (fluids).

Pos. Fig. 2-70: 5

10 11

Fluid

Express coupling for

Gearbox oil for pump transfer gearbox (optional) Hydraulic oil tank

Filling and/or draining

Grease for central greasing system

Filling and/or draining Filling

A service vehicle is needed for filling and/or draining of the fluids.

Lowering the service station Draw out control knob (21, Fig. 2-70:) of valve (22) with rope (25). The service station is brought down to the lower position. Turn knob (21) by 90° and engage.

Note:

Raising the service station

Connections used may vary depending on how the machine is equipped.

Disengage control knob (21) of valve (22), turn by 90° and press in. The service station is raised to the top position.

Refilling and draining For filling in or for draining fluids, unscrew the cap of the corresponding express coupling (Fig. 2-70:).

Attach express coupling of filling hose from the service vehicle to the corresponding express coupling at the service station. Fill in or drain off fluid.

Take off filling hose and refit cap on the express coupling.

Fig. 2-70:

2-62

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Operation

Assemblies resp. Measuring device reservoirs Pump transfer Dipstick (Fig. 2-71:) gearbox

Hydraulic oil tank

Remarks Stop filling when the oil reaches the "max" mark on the dipstick (cf. Part 3, chapter "Pump transfer gearbox Checking the gearbox oil level/Filling in oil").

Inspection glass (1, Fig. Checking the oil level: 2-72:), sign (2. Fig. 2-72: Extend the piston rods of stick and bucket cylinders and Fig. 2-73:) halfway. Stand working equipment on the ground.

Check oil level at an oil temperature of ca. 50 °C (122°F), with the electric motor stationary.

Fill in oil when the oil level in the inspection glass has dropped below the "min" mark. Stop filling if the oil reaches the "max" mark on the inspection glass or the acoustic warning signal "Travel alarm" sounds (cf. chapter "Hydraulic system - Checking the hydraulic oil level / Refilling hydraulic oil").

Fig. 2-71:

Fig. 2-73:

Fig. 2-72:

BA RH170B(3 725 013.00)-EN

2-63

OPERATING INSTRUCTIONS RH170B Electric Operation

Assemblies resp. Measuring device reservoirs

Remarks

Grease container BCS display (Fig. 2-74:) – cental lubricating system

BCS display indicates a warning when the grease container is empty.

Fill in grease using express coupling (11, Fig. 2-75:).

Switch on the display system with the toggle switch (23, Fig. 2-75:). Monitoring lamp (22) lits up.

Stop filling when BCS indicates "Grease container filled". The indicator lamp (24) lights up.

On completion of filling, switch the display system off again with the toggle switch (23). Monitoring lamp (22) is off.

Fig. 2-74:

2-64

Fig. 2-75:

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Operation Battery main switch, switching on and off

Electrical system (24V), switching on and off

When the excavator is disconnected from the medium voltage (7.2 kV) the electrical system (24V) is supplied with voltage by two batteries.

The electrical system is switched on or off with key-switch (32, Fig. 2-77:).

With the battery main switch, the electrical system (24V) is disconnected from the batteries.

The battery main switch is located at the right side wall of the control cabinet (24V). The control cabinet (24V) is mounted in the driver's cab module beneath the driver's cab.

Switching the battery main switch on  Insert switching handle into battery main switch (position "0", Fig. Fig. 2-76:) and turn it to position "I".

Switching the battery main switch off  Turn switching handle from position "I", Fig. Fig. 2-76: to position "0" and withdraw.

Switching the electrical system (24V) on  Insert key into key-switch (32) and turn to the right.

Now all electronical assemblies of the excavator are supplied with voltage, computer systems are started. A selftest is carried out.

The Board Control System (BCS) displays current operating data as well as detected faults.

If there are no critical faults detected BCS enables starting the electric motor.

If there are critical faults or failings detected BCS disables starting the electric motor and displays corresponding explanatory text.

For more information see "Operating Instructions Board-Control-System".

Switching the electrical system (24V) off  Turn key in key-switch (32) to the left and withdraw

Fig. 2-76:

Fig. 2-77:

BA RH170B(3 725 013.00)-EN

2-65

OPERATING INSTRUCTIONS RH170B Electric Operation Switching the electric motor on and off Before switching on the electric motor Before switching on the electric motor, check that nobody is working on the electrical system or on the excavator itself.

Switch on the electric motor only when all these work on the excavator is finished and all persons leave the danger area.  Switch on battery main switch (see: "Battery main switch, switching on and off").  Switch on electrical system (24V) (see: "Electrical system (24V), switching on and off").  Check telltales (14 and 16, Fig. 2-78:), they must lit up in green colour.

If so, electric motor can be switched on (see: "Switching the electric motor on").

Fig. 2-78:

If telltales didn`t lit up in green colour, BCS has detected critical operating conditions or faults which prohibit starting the electric motor. BCS indicates this case with telltales (for instance 15, Fig. 2-78:) as well as by displaying corresponding text.

Switching the electric motor on  Actuate switch-key (51, Fig. 2-79:), the electric motor is switched on.

During starting period the electric motor heavily warm up. Therefore it is not allowed to switch it on and off at will. By means of an electronical time-out circuit (PLC) the electric motor can be switched on only three times a hour (time-out period is 30 minutes).

Fig. 2-79:

2-66

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Operation Switching the electric motor off

Time-out before restart

During breaks in operation and at the end of each shift, the working equipment must be lowered onto the ground.

During starting period the electric motor heavily warms up. Therefore it is not allowed to switch it on and off at will. By means of an electronical timeout circuit (PLC) the electric motor can be switched on only three times a hour (time-out period is 30 minutes).

The electric motor must NOT be switched off until the equipment is resting on the ground.

To avoid straining the vacuum contactor, the electric motor should be shut down only when load-free, i.e. without any of the hydraulic units being activated at the same time via the control valve.  Actuate switch-key (52, Fig. 2-80:). The electric motor starts running down.  Turn key in key-switch (32) counter-clockwise and withdraw.

The control voltage is switched off.

The electric motor only can be switched on again, after the time-out period (30 minutes after last switching on) is over (see: "Time-out before restart", "Before switching on the electric motor" and "Switching on the electric motor").

The 30 minutes period means the time from switching on the electric motor up to the next switching on, e. g.

Electric motor is switched on, runs 20 minutes and then is switched off. Now the time-out period is 10 minutes before restart.

After running more than 30 minutes without interruption the electric motor can be switched on without any time-out period.

PLC prohibits switching on the electric motors until they are cooled down.

Monitoring lamp (14, Fig. 2-81:) on the BCS display is flashing in yellow colour until the time-out period is over. The remaining time is displayed also.

Monitoring lamp lit up in green colour when the time-out period is over and PLC enables switching on the electric motor.

Fig. 2-81: Fig. 2-80:

BA RH170B(3 725 013.00)-EN

2-67

OPERATING INSTRUCTIONS RH170B Electric Operation Electric motor can not be switched on If BCS prohibits switching on the electric motor the operator should check the following:  Time-out before restart period still running? 

EMERGENCY STOP switch in control column unlocked?



EMERGENCY STOP switch in control cabinet (400V) unlocked?



EMERGENCY STOP pullswitch near the service station unlocked?



Servicing switch unlocked?



Monitoring lamps "7.2 kV OK" and "PHASE SEQUENCE OK" on the control cabinet (400V) and on the control column lighting?

If not, the circuit breaker is switched off or the 7.2 kV voltage supply is missing.

 

Shut-off flaps at the hydraulik oil reservoir closed?

Check BCS display: Faults or explanatory text displayed? If so, give information to the electric maintenance personnel.

In case of failure If failures in the electrical systems occur, BCS displayes warnings and corresponding explanatory text Failures in electrical systems may exclusively be removed by specialist personnel for maintenance and service on electrical systems.

The following faults may be responsible:  fault in high-voltage transformer 

7.2 kV/ 400V/ 230V transformer overloaded.



earth fault.

If BCS display shows "Overcurrent", the operator does not know if an "Earth fault" happens. In worst case the excavator may be energized.

The operator must notify the electrician in charge from the excavator superstructure.

The electrician must then cut off the voltage supply from the transformer station and locate and rectify the fault.

If after all of these checks the electric motor cannot be switched on the operator has to inform the specialist personnel for maintenance and service on electric excavators. Only these have the skills to work in a safe way, for trouble shooting and removing the fault.

2-68

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Operation Circuit breaker, switching on and off By means of the circuit breaker the supplied medium voltage 7.2kV can be connected to the excavators electrical system or can be disconnected from it. The circuit breaker is installed in the control cabinet 7.2 kV (Fig. 2-82: and Fig. 2-83:).

Switching the circuit breaker on is possible only when PLC and motor protection relay enable thie function. In this case, monitoring lamp (arrow, Fig. 2-83:) lights up.

The circuit breaker is operated with an actuating lever which is stored in a fixture inside the control cabinet 7.2 kV.

Switching on the circuit breaker  Slip actuating lever (Fig. 2-84:) onto the actuating shaft of the circuit breaker. Pull locking element outwards against spring pressure.  Turn actuating lever by ca. 180° upwards (Fig. 2-84:). This tensions the cut-out spring.  Turn actuating lever (Fig. 2-85:) by 180° downwards.

This tensions the cut-in spring and the circuit breaker is switched on.  Engage locking ring.  The indicator lamps "7.2 kV OK" (1, Fig. 2-86:) and "PHASE SEQUENCE OK" (2) comes on at the control cabinet 400V and at the control column in the driver's cab.  Withdraw the actuating lever and put it into its fixture.

Fig. 2-82:

Fig. 2-84:

Fig. 2-83:

Fig. 2-85:

BA RH170B(3 725 013.00)-EN

2-69

OPERATING INSTRUCTIONS RH170B Electric Operation Switching off the circuit breaker  Slip actuating lever (Fig. 2-87:) onto the actuating shaft of the circuit breaker.  Pull locking element outwards against spring pressure.  Using actuating lever (Fig. 2-87:), turn actuating shaft ca. 20° clockwise.

This releases the cut-out spring. The circuit breaker is switched off.  The indicator lamps "7.2 kV OK" (1, Fig. 2-86:) and "PHASE SEQUENCE OK" (2) goes out at the control cabinet 400V and at the control column in the driver's cab.  Withdraw the actuating lever and put it into its fixture.

Further detailed information is given in the attached leaflet on circuit breakers.

Fig. 2-86:

Fig. 2-87:

2-70

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Operation Motor protection relay, function The electric motor is equipped with a motor protection relay. The relay is located in the 400 V switch cabinet (Fig. 2-88:).

The relay monitors the operating conditions of the electric motor and protects the motor against faults in the electrical system of the motor Depending on the nature of the fault, the motor protection relay switches off  the power supply of the motor via the vacuum contactor or 

the power supply of the machine via the switch-disconnector.

At the factory, the motor protection relay is programmed for the following functions:  protection against overcurrents,

Fig. 2-88:



protection against overloading,



detection of ground faults,



temperature monitoring,



restart inhibit,



protection against undervoltage,



protection against load unbalance (failure of a phase)



phase sequence monitoring,



change of frequency,



run-up period monitoring.

In case a severe fault of the motor system is detected in operation, the motor protection relay is activated and the electric motor shut off automatically.

If the motor protection relay detects a severe fault before or during the starting sequence of the electric motor, it prevents the motor from being started.

Depending on the type of fault detected, one or more LEDs on the front panel light up (9, Fig. 2-89:).

After rectification of the fault press button (7). The LED is extinguished. The motor protection relay is again operational.

For more information please refer to the the manufacturer's description.

BA RH170B(3 725 013.00)-EN

2-71

OPERATING INSTRUCTIONS RH170B Electric Operation Front panel control and monitoring elements See Fig. 2-89:

1 2 3 4 5 6

7 8 9

RUN indicator (LED) Display screen (provides information on states of operation) Display screen navigation keys Function key freely programmable (not used for this machine) Control of other equipment (not used for this machine) USB interface for communication with external devices (only for Bucyrus HEX Service) Reset for LEDs of item 9.

Cover for keypad of item 4.Functional description of the LEDs of item 9.

LEDs G1 – G8, on after detection of a fault: G1 – Overcurrent G2 – Undervoltage/overvoltage G3 – Load unbalance G4 – Frequency change G5 – Overload G6 – Phase sequence fault, ground fault G7 – Run-up monitoring, restart inhibit G8 – Emergency STOP activated

Fig. 2-89:

For more information please refer to the the manufacturer's description.

2-72

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Operation Air conditioner (optional) Ventilation / Heating

Control panel (SIGMA)

The air needed for ventilation and/or heating is sucked in from outside the cab by a blower and ducted to the air outlets.

(see Fig. 2-90: and Fig. 2-91:) 1

Rotary switch

Selects the intensity level of the blower (3 levels).

If necessary, the air in the cab is sucked in through the and recirculated.

2

Rotary switch

The air conditioner control elements are located at the left side of the control column (Fig. 2-90:).

Selects the desired control function (heating, cooling, ventilation, defrosting).

3

Thermostat

The excavator can be equipped with a dual-air conditioning system. The control elements are then installed twice (Fig. 2-91:).

Sets the desired temperature inside the cab.

4

Rotary switch

Selects the intensity level of the blower (3 levels).

5

Rotary switch

Selects the desired control function (heating, cooling, ventilation, defrosting).

6

Thermostat

Sets the desired temperature inside the cab.

Do not switch the air conditioner to "cooling“ when the back-up heating (optional) is on.

Fig. 2-90:

Fig. 2-91:

BA RH170B(3 725 013.00)-EN

2-73

OPERATING INSTRUCTIONS RH170B Electric Operation TRAVELLING THE MACHINE Travelling, Safety Instructions Have the attachment raised only so far as to permit the machine to be driven under overhead power lines without any risk.

Close the cab door.

If the machine is fitted with a safety belt for the operator, fasten the belt.

If the superstructure is turned by more than 90° from the BASIC POSITION, the excavator travels in the opposite direction to that selected.

If the position of the superstructure in relation to the undercarriage is not exactly known, touch the accelerator Lightly to see which direction the machine takes, before initiating the full travelling movement.

Fig. 2-93:

Running-in specifications for components of the crawler tracks:

Warn persons in the immediate vicinity by sounding the horn before setting off.

Prior to initial commissioning and/or after repair work, run in the idlers, track rollers and support rollers as follow:

Never travel across slopes.

 Raise the equipment (Fig. 2-92: and Fig. 2-93:)

Take the utmost care on slippery, greasy ground.

 Travel the excavator in reverse approx. 50 m (164ft).  Travel the excavator in forwards approx. 50 m (164ft).  Stop the excavator.  Measure the temperature at each dler, track roller and support roller with an infrared thermometer. (at a temperature of approx. 100° C (212°F) wait for idlers, track rollers and support rollers to cool down).  Repeat this running-in procedure up to 10x.  Check all idlers, track rollers and support rollers for leaks.

Fig. 2-92:

The electric motor must be at operating temperature before being subjected to full load.

If the machine is to be travelled a longer distance, the superstructure must be secured against turning by means of the superstructure holding brake.

Trailing cable Never touch the trailing cable.

Risk of voltage transfer, if the trailing cable insulation is defective!

Change the position of the trailing cable only by means of a cable hook.

2-74

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Operation Travelling Superstructure basic position Travel direction and sense of actuation of pedals (112 and 113, Fig. 2-95:) are identical only when the excavator is in its BASIC POSITION (Fig. 2-94:).

Travelling forwards/backwards  Travelling forwards: depress pedals (112 and 113) forwards.

The excavator travels in the direction of the idler (2, Fig. 2-94:).  Travelling backwards: depress pedals (112 and 113, Fig. 2-95:) backwards.

The excavator travels in the direction of the drive sprocket (4,Fig. 2-94:).

During travelling, an acoustic warning signal sounds (Travel Alarm).

Fig. 2-94:

If the superstructure is slewed out of its basic position by more than 90° (Fig. 2-96:), the excavator moves in a direction opposite to that expected when pedals (112 and 113, Fig. 2-95:) are depressed.

Fig. 2-96:

The pedals return automatically to their "0" positions when released.

Reverse the excavator only over short distances and with the assistance of marshallers because of restricted rear-view conditions.

Do not travel across slopes.

When travelling uphill or downhill, the travel gears must always be at the rear. Travel only in the basic position of the excavator and only forwards.

Be extremely careful on slippery and greasy ground.

Fig. 2-95:

If the operator is not completely sure of the position of the superstructure with regard to the undercarriage, pedals (112 and 113) should be depressed slightly in order to find out which way the excavator moves before initiating the full travelling movement.

BA RH170B(3 725 013.00)-EN

All instructions with regard to travelling speed regulation and travel direction control are applicable only as long as the crawler tracks have sufficient grip and do not slip.

2-75

OPERATING INSTRUCTIONS RH170B Electric Operation Regulating the travelling speed Travelling on level ground Regulate the travelling speed with  pedals (112 and 113, Fig. 2-97:) and  Switch (71, Fig. 2-98:) to the right (slow gear) All forward/reverse travel movements are possible with this gear.  Switch (71, Fig. 2-98:) to the left (fast gear) The excavator can be travelled only parallel forwards with this fast gear.

The travel gearbox changes automatically into the 1st gear as soon as another travelling function (e.g. reversing, cornering) is initiated.

Change speed range only when the excavator is stationary.

Fig. 2-98:

Travelling uphill and downhill Read and observe the "Travelling Safety instructions" chapter.  Depress pedals (112 and 113, Fig. 2-97:) fully to the limit stop.

When travelling downhill, the travel retarder valve acts as a speed limiter.

The travel retarder valve works correctly only if pedals (112 and 113) are fully depressed down to the limit stop.

Fig. 2-97:

2-76

Should the travelling speed become too high when travelling downhill release pedals (112 and 113) to stop the excavator.

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Operation Cornering  To take a right-hand corner forwards depress only pedal (112, Fig. 2-99:) forwards.

Never use the working equipment to raise one side of the undercarriage and then turn the undercarriage by initiating the slewing and/or the travelling function.

 To take a lefthand corner forwards depress only pedal (113) forwards.

Turning  To turn to the right depress pedal (112) forwards and pedal (113) backwards.  To turn to the left depress pedal (113) forwards and pedal (112) backwards.

This way of working is contrary to the excavator'sdesignated use.

There is a risk of accident. Moreover, the tracks, slewing gear, roller bearing slewing ring or bucket back-wall and the front part of the bucket are subjected to inadmissibly high stresses.

Fig. 2-100: Fig. 2-99:

Note Change the position of the undercarriage - parallel or perpendicular to the working face - only by cornering forwards/backwards (Fig. 2-100:).

Cornering to the left: forwards

from pos. 1 to pos. 2

backwards

from pos. 2 to pos. 3

forwards

from pos. 3 to pos. 4

The same procedure should be adopted if the excavator is to be travelled out of depressions (Fig. 2-101:): Cornering to the left

from pos. 1 to pos. 2

Cornering to the right

from pos. 2 to pos. 3

BA RH170B(3 725 013.00)-EN

Fig. 2-101:

2-77

OPERATING INSTRUCTIONS RH170B Electric Operation Travelling over long distances Travel only forwards with the excavator in its basic position.

Backhoe equipment (Fig. 2-103:):  Fully extend boom cylinder (1).

Travelling backwards over longer distances could result in damaging parts of the undercarriage or the travel gear.

 Retract backhoe cylinder (2).

Read and observe the "Travelling – Safety instructions" chapter.

 Extend backhoe cylinder (2) and stick cylinder (3) to such an extent as to reach the position of the equipment shown in (Fig. 2-103:).

 Retract stick cylinder (3).

When travelling, pay attention to sufficient headroom, e. g. under cable bridges or high-tension cables.

Keep the loading bucket close to the ground. For a more uniform loading of the tracks, the equipment must, however, be kept at a steep angle (Fig. 2-102: and Fig. 2-103:).

Fig. 2-103:

Lower the equipment when travelling underneath obstacles.

If the equipment position must be changed:  stop the excavator, Fig. 2-102:

 change the position, Loading bucket equipment (Fig. 2-102:):  Fully extend boom cylinder (1).  Extend bucket cylinder 2.  Extend stick cylinder 3.  Retract bucket cylinder 2 and stick cylinder (3) to such an extent as to reach the position of the equipment (Fig. 2-102:).

2-78

 continue to travel.

After travelling for 15 minutes without interruption, stop the excavator and check the temperatureof the track rollers.

If the temperature does not exceed approx. 100° C: (212°F) continue travelling.

In case of higher temperatures:  Stop travelling. Resume travelling only after the track rollers have cooled down to approx.

40°C (104°F).

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Operation Superstructure holding brake

Track parking brake

The excavator is equipped with four superstructure holding brakes. The superstructure holding brakes are parts of the swing gears and are used to block the superstructure and the undercarriage.

The excavator is equipped with four track brakes integrated in the track drives.

The superstructure holding brakes are parking brakes.  To activate the holding brakes, press switch (82, Fig. 2-104:): 

when the excavator is parked or



when travelling over longer distances.

The track brakes are parking brakes which relieve the hydro-static travel drives during working operation and which protect the excavator against rolling forwards and backwards.

The brakes are controlled by means of the travel pedals (112 and 113, Fig. 2-105:). In neutral position of the pedals, the brakes are applied and the excavator is braked. During travelling, the brakes are released.

The track brakes can also be activated with switch (72, Fig. 2-104:).

Depending on switch position, the brakes are permanently engaged or are automatically applied after ca. 8 sec. each time the excavator stops.

With this switch position, the brakes are released as soon as the "Travel" function is activated.

Fig. 2-104: Fig. 2-105:

BA RH170B(3 725 013.00)-EN

2-79

OPERATING INSTRUCTIONS RH170B Electric Operation TRANSPORTING THE MACHINE Transport - Safety instructions The machine must be loaded and transported only after all safety regulations have been observed and complied with.

Entrust loading and transporting of the machine to a company experienced in the transport of heavy equipment.

The responsability for loading and transporting lies with the transport company or their representative.

Remove oil, grease, soil, mud, snow, ice and other materials from the excavator's crawler tracks and from ramps and loading platforms of the transport vehicle to minimize slipping.

Transport The dimensions and the service weight of the fully assembled excavator do not allow the excavator to be transported in an undismantled state on a lowbed trailer over public roads.

Therefore, the following components and modules must be dismantled beforehand.

Suspensions points as well as the center of gravity are marked on the modules (see example, Fig. 2-106:).

Dimensions and weights of the machines modules can be found in the annex, chapter “Technical Data” as well as in the “Technical Handbook”.

Secure the transport vehicle against rolling away.

Use only tying equipment of sufficient strength (the weights and dimensions of the excavator are set out in the "Technical specifications").

Fig. 2-106:

2-80

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Operation WORKING OPERATION Safety instructions Read the sections "Fundamental safety instructions" and "Operation, safety instructions" carefully and observe the instructions given in them.

Inspect the site for underground gas, power and water lines before starting work. Any damage to such lines is a risk to life!

Clean off any earth, mud, snow, ice, grease and oil adhering to your working footwear before operating the machine. There is otherwise a risk of slipping off the pedals and initiating inadvertent movements.

Sound the horn to warn persons in the immediate vicinity before starting work.

Running-in instructions for hydraulic cylinders Compression of an oil/air compound in a hydraulic cylinder may result in detonations which might damage pistons and sealing rings.

Prior to initial commissioning and/or after repairs, run in the hydraulic cylinders as follows:  Switch on the electric motor.

The pressure-limiting valve in the hydraulic system must not respond  In the first two working cycles, retract and extend the pistons of the hydraulic cylinders to max. ½ to ¾ (not to the limit stop).

Never change direction suddenly. The waiting time between changes of direction must be at least 4 seconds.

Stop work if anyone is in the hazard range of the machine. Make sure they have left the hazard range before resuming work.

 In the next eight working cycles, retract and extend the pistons of the hydraulic cylinders to the limit stop. The waiting time between changes of direction must be at least 4 seconds.

Never operate the machine unless it is standing on a reasonably horizontal, flat surface. The stability of the machine is otherwise at risk.

 When all hydraulic cylinders have been run in, the excavator can operate.

Ensure that the attachment has adequate clearance below overhead power lines and structures.

Trenches and working faces may give way. Keep well clear of them.

Do not operate the machine, 

when several track rollers or support rollers have been removed;



when one or several slewing gearboxes have failed or been removed;



when one or several teeth on the backhoe or on the shovel are worn or missing;



when parts of the hardfacing layer on the backhoe or on the shovel are worn or missing.

Warming up At low temperatures, switch on the electric motor then activate all hydraulic functions for about 10 minutes (bring to service temperature). For further instructions, see section "Lubricants".

If the BCS indicates problems with the alternator or hydraulic oil filter control (with hydraulic oil at service temperature) light up: Lower the working equipment and switch off electric motor.

Working under these circumstances results in heavy wear and possibly in severe damage and thus in high repair costs.

Such circumstances are considered by Bucyrus HEX as "abusive utilization".

Bucyrus HEX refuses to assume the guaranteee for damage and consequential damage caused by an abusive utilization of the machine.

BA RH170B(3 725 013.00)-EN

2-81

OPERATING INSTRUCTIONS RH170B Electric Operation Working equipment, avoid extreme positions Parts of the attachment may damage the machine if they are moved into extreme positions (see illustrations Fig. 2-107: up to Fig. 2-111:).

Work carefully, avoiding extreme positions of this kind.

Fig. 2-109:

Fig. 2-107:

Fig. 2-110:

Fig. 2-108:

Fig. 2-111:

2-82

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Operation WORKING OPERATION Before starting work Prior to initial commissioning and after repairs on the central lubricating system or the hydraulic cylinders, move the unloaded equipment for abt.

5 minutes.

This is required to ensure an adequate supply of grease to the cylinder bearings when the work starts.

Warming up At low outside temperatures it is necessary to run the hydraulic system up to operating temperature.

The temperatures at which warming up is necessary depend on the type of hydraulic oil used; see also "Oils for hydraulic systems".  Switch on the electric motor and start to perform no-load working movements for abt. 10 minutes with the excavator.

Swinging the superstructure The superstructure can only be swung if the superstructure holding brake is released.  To swing the superstructure to the right: shift control lever (115, Fig. 2-112:) to the right.  To swing the superstructure to the left: shift control lever (115) to the left.

After releasing, the control lever returns automatically to position "0". But the superstructures motion will not be braked automatically then. To bring the superstructure to standstill, shift control lever (115) into the opposite direction of superstructures motion (countering).

Braking the superstructure After releasing, the control lever returns automatically to position "0". But the superstructures motion will not be braked automatically then.

The superstructure is braked only by setting control lever (115, Fig. 2-112:) into the opposite direction (countering).

In an emergency apply parking brake with switch (82, Fig. 2-113:)

Fig. 2-112:

Switching on the electronic excavator control You can only move the working equipment after the electronic excavator control is switched on via switch “SERVO” (74, Fig. 2-113:) and the switch inside the driver’s seat (105, Fig. 2-112:).

Electronic excavator control activated - operator is sitting on his seat.

Electronic excavator control deactivated - driver's seat is empty.

BA RH170B(3 725 013.00)-EN

Fig. 2-113:

2-83

OPERATING INSTRUCTIONS RH170B Electric Operation Working When released, all control levers for working operation return automatically to position "0".

Level a surface only in the bucket's digging direction. Never "beat" or "sweep" with the bucket.

Close bucket completely before beginning to dig. Do not level off a surface with the front shell of the bucket open.

Sound the horn to warn persons in the immediate vicinity before starting work.

Start work after all persons have left the danger area.

Raising and lowering the boom  To raise the boom: pull control lever (116, Fig. 2-114:) backwards.

Fig. 2-114:

Filling and emptying the bucket  To fill/tip back the bucket: shift control lever (116) to the left.  To empty the bucket by dumping/tipping: shift control lever (116) to the right.

 To lower the boom: push control lever (116) forwards.  To lower the boom with pressure: depress button (103) and push control lever (116) forwards.

Extending and retracting the bucket stick  To extend the stick: push control lever (115) forwards.

Opening and closing the bottom-dump bucket  To open the bucket: press pedal (111) forwards / resp. press button (117) to the left.  To close the bucket: press pedal (111) backwards resp. press button (117) to the right.

 To retract the stick: pull control lever (115) backwards.  To retract the stick with pressure: (only on bottom-dump bucket equipment) depress button (102) and push control lever (115) backwards.

2-84

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Operation Emergency lowering of the working equipment

After daily operation

With the electric-motor not functional, the working equipment can be lowered to the ground as follows:  Switch on electrical system (24V) with keyoperated switch (32, Fig. 2-115:).

 Park the machine on level and stable ground. This is particularly important in winter to avoid freezing of the tracks.

 Actuate switch (91) and hold.  Push control lever (116, Fig. 2-116:) forwards.

Parking the machine

 Stand the working equipment on the ground.  Switch off the electric motor.  Shift both control levers into all directions todepressurize the hydraulic cylinders.  Withdraw the key from the electrical systemkey-switch.  Set the battery main switch to OFF.  Close the cab windows.  Lock the cab doors and all lockable hatches and covers on the machine.  Clean the machine of coarse dirt as well as of combustible and easily flammable substances, if possible with a stream jet (rubber parts and electric components with compressed air - refer to information label) Otherwise, the fire and explosion hazard will exist.  Inspect the hydraulic system, the track rollers, support rollers, idlers and gearboxes visually for leaks.

Fig. 2-115:

Escaping oil pollutes the environment.

Repair leaks immediately (or have them repaired).

Report oil accidents to the user of the machine.  Check the superstructure, undercarriage and the working equipment for damage and all steel components for cracks or fractures.  Report detected damage immediately to the user.  Clean off gross dirt, ice and snow from the fins and the fan wheel of the hydraulic oil cooler Fig. 2-116:

BA RH170B(3 725 013.00)-EN

.

2-85

OPERATING INSTRUCTIONS RH170B Electric Operation ASSEMBLING WORKING EQUIPMENT - SAFETY INSTRUCTIONS Personel Assembly work may be carried out only by operating or maintenance personnel who have the necessary know-how at their disposal.

If such know-how is lacking, meticulous instruction must be given by experienced personnel, e.g. from Bucyrus HEX. The operating manual, and in particular the section headed "Fundamental Safety Instructions", must have been read and understood.

Only such persons may start up the machine during assembly work in order to adjust the attachments.

Incorrect operation of the machine or the attachments may give rise to life-threatening situations.

Personal protective gear and working clothes Wear closely fitting working clothing when working on the machine. Loose, wide garments may catch on machine parts and result in injury.

Wear a safety helmet, safety footwear and gloves.

Tools and auxiliaries Tools, hoists, slings, trestles and other devices must be in a reliable, safe state.

Metal splinters may cause injury when accessory bolts are being driven in or out. A brass or copper mandrel should therefore be used for this purpose, and goggles must be worn.

Securing the working equipment Stand working equipment on the ground in such a way that no movements can be made if mechanical or hydraulic connections become detached.

Secure any equipment or component which is to be mounted or dismantled, or whose position is to be changed, with hoists or appropriate slinging/supporting devices to prevent them from moving, slipping or falling inadvertently.

Securing the machine Carry out work on the attachment only if the machine is secured as described in the "Securing the machine" section.

Selecting the attachments The machine can be equipped with various attachments. The components of the attachments are assembled with hydraulic cylinders and connectors. Components can be combined in various ways for optimum adaptation of the attachments to the specific application.

Operate the machine only with the equipment and component combinations expressly approved by Bucyrus HEX for this type of machine.

Never install and commission other equipment and component combinations without Bucyrus HEX first having inspected and approved the project in writing.

Protective roof against falling objects The machine is equipped with an integrated cabprotection roof (FOPS).

Use only the steps, platforms and handrails when climbing onto or off the machine.

Always keep steps and platforms in a non-slip state. Remove any oil, grease, earth, clay, snow, ice and other foreign matter immediately.

2-86

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Operation Securing the machine Risk of injury

Secure the machine as described below:  before carrying out any fitting and modification work on the working equipment,

The machine must not be started by unauthorized persons.



Therefore, secure the machine.

 Park the machine on level and stable ground.

Observe the accident prevention regulations.

Protective shrouds of moving machine parts may only be opened or removed when the drive unit is stationary and protected against inadvertent starting.

Before carrying out fitting works, the machine and the equipment must be protected against inadvertent starting by placing chocks under the tracks and by standing the working equipment on the ground.

before carrying out any servicing and repair work on the machine.

 Lock the superstructure.  Stand the working equipment on the ground.  Switch off the electric motor.  Depressurize the hydraulic system.  Withdraw the key from the key-switch.

Hydraulic and lubricating systems Depressurize pipeline systems, on which work is to be carried out, by appropriate measures.

Close all open bores, pipe and hose connections with pressure-resistant plugs.

Refill collected hydraulic oil back into the hydraulic system only through the return-flow filters. Dispose of non re-usable oils without polluting the environment.

All components of Bucyrus HEX machines have been carefully purpose-coordinated. Trouble-free operation and a long service life can only be achieved with original Bucyrus HEX spare parts.

Respect the sequence of working operations when fitting or replacing the attachments. The sequence has been determined and tested by qualified experts.

BA RH170B(3 725 013.00)-EN

2-87

OPERATING INSTRUCTIONS RH170B Electric Operation CORROSION PROTECTION FOR PINS AND BEARINGS (BUSHINGS AND HUBS) Use GLEITMO 815 anti-corrosive agent only.

Other agents are not approved by Bucyrus HEX. All pins and bearings (bushings and hubs) of the working equipment or in equipment componenents must be treated GLEITMO 815 anti-corrosive agent before fitting.

GLEITMO 815:  permits easy fitting and dismantling, 

protects against rust, oxidation and similar wear,



prevents seizing and fretting corrosion in nonmoving parts of bearings.

This is achieved by aluminium and copper particles forming a protective layer on the metal. This layer removes surface irregularities and does not sweat, seize or harden.

Application of GLEITMO 815  Clean off grease, oil, dirt and corrosion protection agents from pins and bearings using white spirit or diesel fuel.

Rust patches must be thoroughly removed, if any.

All parts must present a dry, bright metal surface.  Apply a thin layer of GLEITMO 815 on pins and all bearings using a brush or a spray can.

Pin shafts and bearings must be completely co-vered by the protective layer.

If the protective layer of a pin already treated with GLEITMO 815 is damaged, these areas must be touched up before fitting the part.  Fitting and securing of pins If the pin is too heavy to be fitted manually, apply GLEITMO 815 at first only on abt. a quarter of the pin's length Then position pin by means of a lifting gearready for fitting.

Apply GLEITMO 815 on the remaining length of pin shaft, fit pin and secure.

Part number of GLEITMO 815 is 2764305. Available from Bucyrus HEX Spare-Parts Service

2-88

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Operation NOTES ................................................................................................................................................................... ................................................................................................................................................................... ................................................................................................................................................................... ................................................................................................................................................................... ................................................................................................................................................................... ................................................................................................................................................................... ................................................................................................................................................................... ................................................................................................................................................................... ................................................................................................................................................................... ................................................................................................................................................................... ................................................................................................................................................................... ................................................................................................................................................................... ................................................................................................................................................................... ................................................................................................................................................................... ................................................................................................................................................................... ................................................................................................................................................................... ................................................................................................................................................................... ................................................................................................................................................................... ................................................................................................................................................................... ................................................................................................................................................................... ................................................................................................................................................................... ................................................................................................................................................................... ................................................................................................................................................................... ................................................................................................................................................................... ................................................................................................................................................................... ................................................................................................................................................................... ................................................................................................................................................................... ................................................................................................................................................................... ...................................................................................................................................................................

BA RH170B(3 725 013.00)-EN

2-89

OPERATING INSTRUCTIONS RH170B Electric Operation

2-90

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing 3 INSPECTION AND SERVICING

Operating instructions

Part 1 INTRODUCTION FUNDAMENTAL SAFETY INSTRUCTIONS Part 2 OPERATION

Target group

Operating personnel + Inspection and servicing personnel + Repair personnel Operating personnel The operating personnel must have knowhow relevant to the operation and the application of this or comparable machines.

Part 3 INSPECTION AND SERVICING Part 4 REPAIR WORK

Inspection and servicing personnel The inspection and servicing personnel must have know-how relevant to the inspection and servicing of this or comparable machines.

Repair personnel The repair personnel must have know-how and experience relevant to the repair of this or comparable machines.

Part 5 ANNEX

Part 6 INDEX

BA RH170B(3 725 013.00)-EN

Operating personnel + Inspection and servicing personnel + Repair personnel Operating personnel + Inspection and servicing personnel + Repair personnel

3-1

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing

3-2

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing SAFETY INSTRUCTIONS FOR EXCAVATORS WITH ELECTRIC MOTOR

Connect the earthing kit (8) to the earthing points (2, 3 and 4) only by means of extension (5).

Maintenance and inspection work on electrical systems may only be performed by qualified electricians or by workshops employing such personnel.

The earthing points may still carry residual voltages.

A qualified electrician for the purpose of this regulation is a person who has the corresponding technical training, know-how and experience as well as knowledge of the pertinent prescriptions and who is therefore in a position to judge the work entrusted to him and the potential dangers in connection therewith.

Before carrying out any maintenance and inspection work on the electrical system, the following precautions must be taken:

In the transformer station  Cut out the supply voltage.  Secure against switching on; apply a warning sign.

Fig. 3-1:

 Check that the electrical system is off circuit.  Connect to earth and short-circuit.  Protect adjacent and live parts against accidental contact.

On the excavator  Cut out the switch-disconnector (see the " Switching off the circuit breaker " chapter in part 2 of the present operating instructions)  Secure the circuit breaker against switching on, e.g. seal in the actuating lever in a cabinet.  Apply a warning sign.  Remove the cover (1, Fig. 3-1:).

Fig. 3-2:

 Check that the electrical system is off circuit and dead. 

Connect to earth and short-circuit: (connect the earthing and short-circuiting line (8, Fig. 3-2:) in the following order to points (1 – 4): first to the fixed point (1), then one after another to the earthing points (2, 3 and 4).

 Slide partition (6, Fig. 3-3:) into guide (7).

Fig. 3-3:

BA RH170B(3 725 013.00)-EN

3-3

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing After inspection and maintenance at the electrical system, the following works must be performed:

On the hydraulic excavator  Disconnect the earthing and short-circuiting line (8, Fig. 3-4:): first from the earthing points (2, 3 and 4) by means of extension (5), then from the fixed point (1).  Withdraw the partition (6, Fig. 3-5:).  Refit the cover (1, Fig. 3-6:).

Fig. 3-6:

In the transformer station  Disconnect the earthing and short-circuiting line.  Unlock the safety device preventing switch-on; remove the warning sign.  Remove the partitions.

Fig. 3-4:

 Switch on the supply voltage.

On the hydraulic excavator  Remove the warning sign.  Cut out the switch-disconnector (see the " Switching off the circuit breaker " chapter in part 2 of the present operating instructions).

Fig. 3-5:

3-4

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing INSPECTION AND SERVICING SAFETY INSTRUCTIONS Operating manual No inspection and servicing work must be carried out until the operating manual has been read and understood.

Pay special attention to: Fundamental safety instructions" and all warnings and safety instructions attached to the machine.

The operating manual lists all jobs to be done. The descriptions of job sequences, however, provide only Experienced personnel with the necessary instructions.

The operating manual must be kept with the machine at all times.

Inspection and servicing personnel Inspection and servicing personnel must have the necessary know-how on the inspection and servicing of this or comparable machines.

The necessary know-how can be acquired in a several day's instruction, e.g. by an Bucyrus HEX mechanic or by attending an Bucyrus HEX training course.

Securing the working equipment Stand working equipment on the ground in such a way that no movements can be made if mechanical or hydraulical connections become detached.

Secure any equipment or component which is to be mounted or dismantled, or whose position is to be changed, with hoists or appropriate slinging / supporting devices to prevent them from moving, slipping or falling inadvertently.

Securing the machine Carry out servicing work only if the machine is secured as described in the section "Securing the machine".

Climbing onto and off the machine Use only the ladders, steps, platforms and handrails provided when climbing onto or off the machine.

Always keep ladders, steps, platforms and handrails in a non-slip, safe state and remove any oil, grease, soil, clay, snow, ice and other foreign matter immediately.

Always face the machine when climbing on and off.

Checking the state of tools Personal protective equipment and working clothing

Use only fully functional, reliable tools.

Wear closely fitting working clothing when working on the machine. Loose, wide garments may catch on machine parts and result in injury.

Wrenches of the wrong size, for example, may slip and cause injury.

Select the right tool for the job.

Wear a safety helmet, safety footwear, gloves and, in the event of high noise levels, ear protectors.

BA RH170B(3 725 013.00)-EN

3-5

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing Cleaning jobs

Fastening and securing elements

Prior to commencing work, clean your working area, if necessary and possible, with a stream jet (rubber parts and electric components with compressed air - refer to information label).

Check fastening and securing elements, e.g. bolts, nuts, washers, before using them again.

Use only lint-free cleaning rags when working on the hydraulic system.

Cleaning agents and solvents may give off harmful, readily flammable vapours. Never work with such agents except on well ventilated premises; never inhale the vapours and never smoke.

Prevent solvents and cleaning agents from coming into contact with your skin.

Wear gloves.

Observe the instructions on the packaging.

Replace any damaged parts.

Spare parts Use only the original sparts parts of Bucyrus HEX. They are the only ones to fulfill the technical specifications of the machine.

Handling oils and greases Hot lubricant or hydraulic oil emerging uncontrolled from the system may result in severe burns.

Never set foot withing reach of the emerging oil jet.

Handling flammable liquids When handling flammable liquids:  never smoke,

Avoid contact with the skin. Wear gloves and firm protective clothing.

Used oil may be harmful to the skin.

keep away from unshielded light sources and naked flames,

Clean soiled skin thoroughly with warm soapy water and apply a barrier cream. Never use fuels or solvents for cleaning the skin.

Consumables often have low flash points and are readily ignited. Never attempt to extinguish burning liquids with water.

If you have swallowed any oil, avoid vomiting but consult a doctor immediately.

Use:  dry powder,

Visisble oil losses



carbon dioxide or

Have any visible leakage repaired immediately.



foam extinguishers.



Water used for extinguishing purposes would vapourize instantaneously on contact with burning substances and spread burning oil, for example, over a wide area. Water generates short circuits in the electrical system, possibly producing hazards.

Escaping oil is an environmental hazard.

Soak up any oil that has escaped with a binding agent.

Sweep up binding agent and dispose of it separately from other waste.

Notify the fire brigade.

3-6

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing Relieving residual pressure in the hydraulic system

Screwed connections, piping, hydraulic hoses

Only unpressurized hydraulic systems may be opened. Even when a machine is parked on a horizontal surface with ist attachments supported on the ground and its electric motor switched off, there may still be substantial residual pressure in parts of the hydraulic system, e.g. primary pressure from the last hydraulic movements prior to stopping the machine.

Repair any leakage in the piping and hose system immediately.

Residual pressure is reduced only gradually. If an intervention into the hydraulic system is to be undertaken

A fine, highly pressurized jet of hydraulic oil can penetrate the skin.

Never search for leakages with the fingers, but use a piece of cardboard and always wear goggles.

If oil has penetrated into the skin, consult a doctor immediately.

Never repair damaged piping; always replace them.

immediately after stopping, the system must be depressurzized:

Replace hydraulic hoses immediately on detecting any damage or moist areas.

(do not leave the driver's seat)  Stand working equipment on the ground

Tighten leaking screw plugs only when the system is depressurized.

Escaping oil is an environmental hazard.

 Switch off the electric motor  Move all control levers and pedals repeatedly into all ndirections.

BA RH170B(3 725 013.00)-EN

3-7

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing Non-polluting disposal

Seals

Dispose of oils, greases, cooling liquids, detergents, solvents and oil-containing components, such as filters, cleaning rags, replaced wearing parts and unusable machine parts, without polluting the environment and separately from other waste.

Individual spares may contain asbestos. Such

Do not dispose of these substances together with household wastes.

Clean sealing faces prior to assembly.

spares or their packaging are marked with: Never process spares containing asbestos mechanically. Inhaling asbestos dust is a health hazard.

Fill these substances into the containers provided for such purposes.

Like any other oil, also bio-degradable, "environmental-friendly" hydraulic oil must be disposed of separately.

Do not allow oils and oily wastes to penetrate into the soil or into water. They are an environmental hazard

3-8

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing Handling batteries Battery Posts, terminals and related accessories contain lead and lead compounds, chemicals known to cause cancer and reproductive harm.

Wash hands after handling

Before working on the electrical system

Batteries give off explosive gases.

Before performing work on the electrical system where tools, spare parts, etc. can come into contact with electrical conductors or contacts, the battery must be disconnected.

Never handle batteries close to naked flames and unshielded light sources, never smoke.

Disconnect first the negative and then the positive terminal.

Battery acid is toxic and corrosive.

After the work:

Avoid any contact with the skin, mouth, eyes and clothing. Avoid spilling battery acid or inhaling the vapours.

Reconnect first the positive and then the negative terminal.

Wear gloves, firm protective clothing and goggles when handling batteries.

If the skin is splashed with acid, rinse thoroughly with running water and consult a doctor.

If the eyes are splashed with acid, rinse thoroughly with running water and consult a doctor immediately.

Never set tools down on the battery. They may induce a short circuit, causing irreparable damage to the battery and injuring persons.

Never wear metal necklaces, bracelets or watchstraps when working on the battery. The metal parts may induce a short-circuit resulting in burns.

Dispose of used batteries separately from other waste in the interests of environmental protection.

BA RH170B(3 725 013.00)-EN

3-9

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing Selecting oils and greases

After servicing

Use the recommended qualities only, matching viscosities with the temperature level.

To prevent corrosion, coat all bright metal parts with a grease film.

Filters

On completing work, re-install all protective devices.

Replace / clean all filter elements or filter cartridges within the specified periods.

All filters are coordinated carefully with the equipment. Original Bucyrus HEX parts must be used to ensure smooth running and a long service life of the electric motor and the hydraulic units.

Never switch on the electric motor while work is being done on the machine.

Carry out performance tests with the machine.

Sealing elements When dismantling parts, watch for sealing elements.

Check sealing elements prior to installation and replace any that are even slightly damaged.

When assembling, ensure a perfect fit.

Oil-level check and oil change Position the machine horizontally.

Change the oil when the machine is at operating temperature. Warm oil flows better and carries suspended particles.

Lubricating Clean the lubricating nipple, then lubricate as scheduled.

3-10

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing FIRE AND EXPLOSION HAZARD Safety instructions

Place suitable fire guardings (fire barriers) if open fire or flying sparks cannot be avoided during repair work.

Prior to commencing work, obtain information on the national and corporate rules for the prevention of accidents.

Apply special protection to cables, cable ducts as well as to hose and pipe lines.

Pay particular attention to hazards caused by combustible and easily flammable substances.on the safe handling of the fire extinguishers to be used.

Ensure sufficient ventilation.

Avoid smoking and open fire on, next to and below the excavator.

Combustible and easily flammable substances or liquids increase the fire and explosion hazard.

Do not store or handle any flammable substances during operation.

Clean the excavator thoroughly, if possible, with a steam jet (rubber parts and electric components with compressed air - refer to information label), when, for example, oil, grease, solvent or cleaner was spilled.

Such substances may spontaneously ignite if they get into the vicinity of hot units or objects.

Even battery gases can ignite in open flames or fire.

If necessary, also cover the ground with fireprotective blankets.

Clean the excavator before starting a job.

Do not keep any fire extinguishers that are not suitable or have not been tested.

Do not extinguish flammable liquids with water.

Use:  dry-powder, 

carbon-dioxide or



foam extinguishing compounds.

When getting into contact with burning substances, the fire-fighting water would abruptly evaporate and distribute the substance such as burning oil over a wide area. Water causes short-circuits in the electrical system thus possibly entailing new hazards.

DANGER TO LIFE Call the fire brigade.

Have all your welding, flame cutting and grinding work approved.

Avoid parking the excavator in places where  combustible substances such as coal dust or tar are present. 

open or smouldering fire may occur.

Remove the excavator from such an area where combustible or easily flammable liquids have spilled from the excavator onto the ground.

Flying sparks (caused by welding, flame cutting, grinding, electrical short-circuit) may cause fire on the ground that can spread to the excavator.

BA RH170B(3 725 013.00)-EN

3-11

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing

3-12

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing INSPECTION AND SERVICING PLANS - INSTRUCTIONS Intervals The inspection and Servicing plan lists all jobs which have to be done on the machine at regular intervals.

The individual inspection and Servicing plans are marked with letters providing a link between the operating hours (OH) recorded by the hours-run meter of the machine and the inspection and sServicing plans.

Plan V N

Do all jobs .... ...once prior to initial commissioning. ...after initial commissioning and during the running-in period (after 100 OH). ...every 10 OH or every working shift 1) T ...every 60 OH or weekly . 2 W ...after every 500 OH. B ...after every 1000 OH. C ...after every 5000 OH. D ...after every 10000 OH. E OH = Bh = Operating hours

Oils / Greases For the specification of oils and greases to be used refer to the "Lubricants" section.

The numerals mentioned in the "Oil / Grease" column in the inspection and sServicing plans have the following meaning: Oils for combustion engines and I compressors Oils for hydraulic systems II IIIa, b, c Oils for gearboxes Greases for bearings and slewing V rings

Cleaning jobs Cleaning jobs, especially on cooling systems, must be done at shorter intervals if the machine is exposed to severe dust build-up.

Components The maintenance intervals for components, e.g. electric motor and gearboxes, are listed in the following Bucyrus HEX maintenance schedules.

It is possible that the manufacturer's documentation for these components states intervals deviating from the above-mentioned intervals.

In such case, only the maintenance intervals specified by Bucyrus HEX shall apply.

2

Whichever comes first.

BA RH170B(3 725 013.00)-EN

3-13

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing

3-14

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing Plan V Plan V - Once prior to initial commissioning Page 1 of 2 Location

Servicing work

Electric motor

Lubricate bearings (Follow instructions on the information signs / plates on the motor) Check direction of rotation (cf. electric motor manufacturer´s servicing instructions)

Electrical system Battery Lighting Terminals Slip ring assembly Switch gear cabinets Monitoring, warning and control elements Button - EMERGENCY OFF Button (servicing works) BCS Hydraulic system

Hydraulic oil reservoir Hydraulic cylinders Pump transfer gearbox - Pre-chambers expansion reservoir Swing gearbox (Gearbox P/N 3692960) Swing gearbox (Gearbox P/N 3676892) - Expansion reservoirs Travel gearbox - Pre-chambers /spur gear section - Hydraulic motor chamber Slewing ring Internal gearing Undercarriage Track roller Support roller Track Idler

3

Check liquid level Check operation Check for tightness Visual inspection Check for condensate, drain condensate Check function of monitoring, warning and control elements Check function Check function Check function Check function of working and travelling movement Check pressure (cf. Technical handbook) Check oil level Vent (cf. chapter “venting hydraulic system“) Check oil level Check oil level Check oil level Check oil levels Check oil level Check oil level Check oil level Check grease filling Check for leaks and free movement Check grease filling, fill with grease 3 Check for leaks and free movement Check grease filling, fill with grease3 Check pressure (see Technical Handbook) Check for leaks and free movement

Quantity/ No. 2

2

3 1 1

1

3 6 2 2x1 2x2 1 2x7 2x2 2 2

Valid only for excavators equipped with automatic greasing system for the undercarriage

BA RH170B(3 725 013.00)-EN

3-15

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing Plan V - Once prior to initial commissioning Page 2 of 2 Location Central lubricating system - Grease container - Greasing and pause cycles - Level gauge Service – Station (tanklift) Air conditioner (optional) - Compressor Hydraulic ladder - central lubricating point All lines, fittings and connections All articutated joints and hinges On-board crane (optional) - Fastening bolts - Bearings - Joint (column / boom) - Cylinder bearing - Swing ring Hydraulic oil reservoir

Crane drive engine

- Battery Escape ladder (optional) - Locking device - Ladder Harness (optional) - Harness holding device on cab roof

3-16

Servicing work

Quantity/ No.

Check filling level Check setting Check function Check operation

1

Check oil level Grease Inspect visually for leaks, wearing marks Grease Check for tightness Lubricate Lubricate Lubricate Grease Check oil level (see: “On-Board Crane“ operating instructions) Check oil level (see: “Crane drive Engine“ operating instructions) Check liquid level Check function Check function Check free movement Check completeness and condition Check for tightness

16 4 2 5 1 1

1

2

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing Plan N Plan N – After initial commissioning and during the running-in period (After 100 OH) Page 1 of 1 Location

Electrical system Medium-voltage cells - mechanical connections - lines - terminals and plug connections Hydraulic system Oil cooler - Bearing - Fastening screws Return-flow filter Magnetic rod Pressure accumulator – emergency lowering Pressure accumulator – hydraulic ladder Pump transfer gearbox - Pre-chambers expansion reservoirs - Fastening screws Swing gearbox (Gearbox P/N 3692960) - Fastening screws Swing gearbox (Gearbox P/N 3676892) - Brake chambers - Fastening screws Travel gearbox - Pre-chambers / spur gear section - Hydraulic motor chambers Fastening screws Swing ring Fastening screws (slewing ring, undercarriage and superstructure) Superstructure Fastening screws, especially at superstructure / pedestal / driver´s cab Cable guide for power supply cable - Fastening screws cable guide / machine All lines, fittings and connections

4

Servicing work

Quantity/ No.

Check for tightness Check for tightness Check for tightness

Check for tightness Replace Clean Check function Check function Change oil Change oil Check for tightness Change oil Check for tightness Change oil Change oil Check for tightness Change oil Change oil Change oil Check for tightness

2x7 1 1 1 14 2x34 34 34 34 24 2x14 2x24

Check for tightness (cf. Technical handbook)

Check for tightness (cf. Technical handbook)

Check for tightness (cf. Technical Handbook) Inspect visually for leaks, wearing marks

cf. “Refilling quantities – Oil“ table

BA RH170B(3 725 013.00)-EN

3-17

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing

3-18

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing Plan T and W Plan T - Every 10 OH or every working shift (whichever comes first) Plan W - Every 60 OH or every week (whichever comes first) Page 1 of 2 Location

Servicing work

Quantity/ No.

Plan T

Electric motor - Cooling fins Electrical system

Listen for unusual machine noise Clean



Plan W  

Lighting

Check operation





Switchgear cabinets

Check for condensate, drain condensate





- Electrical components

Visual check



- Breather filter - Dust trap

Remove dust

3



Buttons - EMERGENCY OFF

Check function

3



Button (servicing works)

Check function

1



Monitoring, warning and control elements BCS

Check function of monitoring, warning and control elements Check function

Hydraulic system

Check function of working and travelling movement Inspect visually for leaks

1

















Hydraulic oil reservoir Oil cooler

Check oil level Check / clean

1 2



 

Fan wheel

Check condition

2





Pump transfer gearbox

Check oil level

1

- Expansion reservoir

Check oil level

1

Oil filter (tell-tale)

Check

1

Swing gearbox (P/N 3692960) Swing gearbox (P/N 3676892) - Expansion reservoirs

Check oil level

3





Check oil level

6





Travel gearbox

Check for leaks

2





Escape ladder (optional) - Locking device - Ladder

Check function Check function Check free movement

  

  

Emergency escape device / seat - Holding device - Harness

Visual condition check Check tightness and fixation on cab Connect to the holding device

  

  



- Pre-chamber

BA RH170B(3 725 013.00)-EN



 

3-19

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing Plan T - Every 10 OH or every working shift (whichever comes first) Plan W - Every 60 OH or every week (whichever comes first) Page 2 of 2 Location

Servicing work

Undercarriage Tracks

Inspect track tension visually

Track roller

Check for leaks and free movement

2x7



Support roller

Check for leaks and free movement

2x2



Idler

Check for leaks and free movement

2



Central lubricating system - Grease container

Check filling level





- Lubricating points

Check visually



Air conditioner (option)

(Carry out all service work described in the “Air Conditioning manual“ of the supplier)

 





 

 





On-board crane (optional) 5 Fastening bolts Crane drive engine

Check for tightness Check oil level (see: “Crane drive Engine“ operating instructions) Check oil level Check

Hydraulic oil reservoir - Reflow filter (contamination indicator) Check condition Fire extinguisher Automatic fire-extinguishing sys- Check control module tem (optional) All lines, fittings and connections Inspect visually for leaks, wearing marks Overall cleaning Excavator

Quantity/ No.

Plan T

Plan W

2





16 1

1 1 4 1



5 Before each deployment of the crane

3-20

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing Plan A – E Plan A - after every 250 OH (at 250, 750, 1250 ... OH) Plan B - after every 500 OH (at 500, 1500, 2500 ... OH)

Plan C - after every 1000 OH (at 1000, 2000, 3000, 4000 ... OH)

Plan D - after every 5000 OH (at 5000, 15000, 25000 ... OH)

Plan E - after every 10000 OH (at 10000, 20000, 30000, ... OH) Page 1 of 5

Location

Servicing work

Menge / No.

Servicing in acc. with W or T Monitoring, warning and control elements - Joystick - Control spool - Pedal - Control spool (machine with loading shovel) Electric motor

Plan Plan Plan Plan Plan A B C D E     

Clean / Grease lightly

2x46







Clean / Grease lightly

3x26







 

 

 





 

 

 

 

Rotor (inside and outside of machine) Terminals

Coupling Screw connections Stator windings

6

Lubricate bearings (Follow instructions on the information signs / plates on the motor as well as the motor manufacturers maintenance instructions) Check for vibration Visual inspect interior of machine for degree of dirt deposits and clean if necessary Visual inspect all accessible places for rust Check tightness Check for degree of dirt deposits Check for alignment and record measurements Check condition and tightness Check insulating resistance Information about further maintenance work cf. Electric motor manufacturer´s servicing instructions



2 1 

 

 

 

apply a thin layer of low temperature grease

BA RH170B(3 725 013.00)-EN

3-21

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing

Plan A – after every 250 OH (at 250, 750, 1250 … OH) Plan B – after every 500 OH (at 500, 1500, 2500 … OH)

Plan C – after every 1000 OH (at 1000, 2000, 3000, 4000 … OH)

Plan D – after every 5000 OH (at 5000, 15000, 25000 … OH)

Plan E – after every 10000 OH (at 10000, 20000, 30000, … OH)

Page 2 of 5 Location Electrical system Battery cable connections Battery Slip ring assembly

Mechanical components Switchgear cabinets - Filter mat - Medium-voltage cells - Electrical components - Breather filter - filter element

3-22

Servicing work

Menge / No.

Plan Plan Plan Plan Plan A B C D E  

  

  

  









Visual inspection Clean/dry Check for tightness

  

  

  

  

Clean Replace



 

 

 

Check for tightness Check fluid level Visual inspection, if necessary clean inside from wear debris and grease.

(C.f. Slip ring manufacturer´s servicing instructions) Check for tightness

2

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing

Plan A - after every 250 OH (at 250, 750, 1250 ... OH) Plan B - after every 500 OH (at 500, 1500, 2500 ... OH)

Plan C - after every 1000 OH (at 1000, 2000, 3000, 4000 ... OH)

Plan D - after every 5000 OH (at 5000, 15000, 25000 ... OH)

Plan E - after every 10000 OH (at 10000, 20000, 30000, ... OH) Page 3 of 5

Location

Servicing work

Hydraulic system

Check pressure (cf. Technical handbook)

Oil cooler - Bearing - Fastening screw - Rubber bearing Return-flow filter Return-flow filter (cooling circuit) Bypass valve Bypass valve (cooling circuit) Magnetic rod High-pressure filter Filter (control circuit) Filter (pump control circuit) Filter (swing pump feeding circuit)

Hydraulic oil reservoir Breather filter Pressure accumulator Cylinder (seals and guide rings)

7

Menge / No.

Check for tightness Check condition Replace Replace

2x7 2

Check / clean filter sieve Check / clean filter sieve Check / clean Check / clean Replace Check / clean Replace Check / clean Replace Check / clean

4 2 2 4 4 1 1 2x1 2x1 2x2

Replace

2x2

Carry out oil analysis Change oil Replace Check pressure (cf. Technical handbook) Replace

1 1

Plan Plan Plan Plan Plan A B C D E   

   

   

   

   

         

         









 

 

   

  



7 8

4 3



cf. “Refilling quantities – Oil“ table

8

Unless it is regulary analyzed, the hydraulic oil must be changed every 5000 OH or after 3 years at the latest BA RH170B(3 725 013.00)-EN

3-23

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing

Plan A - after every 250 OH (at 250, 750, 1250 ... OH) Plan B - after every 500 OH (at 500, 1500, 2500 ... OH)

Plan C - after every 1000 OH (at 1000, 2000, 3000, 4000 ... OH)

Plan D - after every 5000 OH (at 5000, 15000, 25000 ... OH)

Plan E - after every 10000 OH (at 10000, 20000, 30000, ... OH) Page 4 of 5

Location

Servicing work

Pump transfer gearbox

Carry out oil analysis Change oil Clean Change oil

- Breather filter - Pre-chambers expansion reservoir - Breather filter Oil filter

Menge / No. 1 19 1 29

Plan Plan Plan Plan Plan A B C D E             

1 2

 

 

 

    

    

    

    



    

    









































Clean Check for contamination and damage Replace Carry out oil analysis Change oil Replace Change oil

2 3 39 3x1 39

Carry out oil analysis Check oil level Change oil Clean Check oil level

2 2 29 2x6 2x1 2x19 2x1 2x2 2x29 2x1



- Breather filter

Change oil Clean Check oil level Change oil Clean / replace

Swing ring

Check grease filling

1

Swing gearbox - Breather filter - Brake chamber (Gearbox P/N 3676892 only) Travel gearbox

- Magnetic rod - Pre-chambers / spur gear section - Magnetic rod - Hydraulic motor chambers

Gearing / pinion

Check condition

Fastening screws (swing ring, undercarriage and superstructure) Undercarriage

Check for tightness (cf. Technical Handbook)

- Diaphragm

Check wear (cf. Technical Handbook) Check pressure (cf. Technical handbook) Replace

Hydraulic ladder - central greasing nipple

Lubricate

Diaphragm accumulator

9

2



  

 

 



 

 

2x1 

cf. “Refilling quantities – Oil“ table

3-24

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing Plan A - after every 250 OH (at 250, 750, 1250 ... OH) Plan B - after every 500 OH (at 500, 1500, 2500 ... OH)

Plan C - after every 1000 OH (at 1000, 2000, 3000, 4000 ... OH)

Plan D - after every 5000 OH (at 5000, 15000, 25000 ... OH)

Plan E - after every 10000 OH (at 10000, 20000, 30000, ... OH) Page 5 of 5

Location

Servicing work

Central lubricating system

Check function

Oilfilter (hydraulic circuit grease pump)

Check for contamination and damage Replace Check for contamination and damage Replace

Grease filter (grease lines)

Grease filter (filling grease container) Breather filter

On-board crane (optional) - Bearing - Joint (column / boom) – Cylinder bearing – Swing ring Hydraulic system – Return-flow filter – Breather filter

Quant. / No.

Plan A

Plan B 

Plan C 

Plan D 

Plan E 

1







1 1



 

 





















1

Check for contamination and damage Replace

2 2

Check / replace

1

Lubricate Lubricate Lubricate Grease Change oil Replace Replace see: “On-Board Crane“ operating instructions Clean Change oil Replace Check for tightness Replace Replace Check for tightness see: “Crane Drive Engine“ operating instructions

4 2 5 1 1 11 1 1

10

Crane drive engine - Oil filter – Fastening screws – Fuel filter – Air filter – Battery cable connection





















1 1 11 1 1 1 1 2

Air conditioner (optional)

(cf. “Air Conditioning manual)







- Filter mats

Change







Steel components

Visual inspection acc. to “Structural Inspection Report every 500 OH” 12 Inspection with dye penetrant test acc. to “Structural Inspection 12 Report every 5000 OH” Check for tightness Grease











 

 

Modules, fastening screws All articulated joints and hinges



 

10

Do all servicing jobs at least once a year and when necessary see: “Refilling quantities – Oil“ table 12 „Structural Inspection Reports“ for inspections every 500 OH and every 5000 OH can be downloaded from the Bucyrus HEX website, section „Support, Warranty“.

11

BA RH170B(3 725 013.00)-EN

3-25

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing LUBRICATING CHART – GREASE

Fig. 3-7:

Lubricating chart – Grease (legend)

3-26

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing No. Greasing point

Number

Lubricant properties

Grease every .... operating hours 10

1

Central lubricating system – grease container

1

3

Electric motor

2

V 13

5

On-board crane

1000 (refer also to the electric motors type plates and information signs) 250

- Bearing - Joint (column / boom)

4 2

V 13

250 250

- Cylinder bearing

5

- Swing ring

1

6

250

Graphitespray

250

V 13

1000

Monitoring, warning and control elements - Joystick - Pedal

2 x 4 14 3x2

14

1000

All other greasing points are supplied with grease by the central lubricating system.

Filling quantities - Grease Greasing point Central lubricating system – grease container (depends on the type of container built in) Internal gearing – Roller-bearing slewing ring

Lubricant properties

V 13

Idler (permanent grease filling) Track rollers (permanent grease filling) (only when not connected to to the central greasing system) Support rollers (permanent grease filling) (only when not connected to to the central greasing system)

13

cf. "LUBRICANTS" section

14

apply a thin layer of low temperature grease

BA RH170B(3 725 013.00)-EN

Tribol Bucyrus HEX part no.

2764564

Filling quant. in kg lb appr. 180 – 1000 appr. 300

appr. 397 – 1102 appr. 661

2 x appr. 25

2 x appr. 55

14 x appr. 15

14 x appr. 33

4 x appr. 14

4 x appr. 31

3-27

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing INSPECTION PLAN - OIL

Fig. 3-8:

3-28

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing Inspection plan – Oil (legend) No. Location

Change oil every ... OH 10000 16

60

1000

10

1000

10

1000

10 10

1000 1000

I II

10

250 17

10

1000 18

III.c

500

5000

2x1

500

5000

2x2

500

5000

Lubricant properties 15

II III.a

1

Hydraulic system

1

2

Pump transfer gearbox

1

- Pre-chambers expansion reservoir Swing gearbox (Gearbox P/N 3692960) Swing gearbox (Gearbox P/N 3676892) - Expansion reservoir - Expansion reservoir brake chamber On-board crane (optional)

1

3 3

5

3

3x2 3x2

- Crane drive engine

1

- Hydraulic oil reservoir

1

4, 6 Travel gearbox - Pre-chambers spur gear section - Hydraulic motor chambers

15

Check oil level every ... OH 10

Number

2

III.b III.b

cf. "LUBRICANTS" section

16

Change hydraulic oil every 5000 OH unless the oil is analyzed at regular intervals, but not later than every 3 years.

17

Change oil at least once a year.

18

Change hydraulic oil at least once a year.

BA RH170B(3 725 013.00)-EN

3-29

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing Filling quantities - oil Location

Filling quantity

Oil

litres

gal

Hydraulic oil reservoir

appr. 4000

appr. 1057

Hydraulic system

appr. 6400

appr. 1690.7

Pump transfer gearbox

appr. 149

appr. 39.4

- Pre-chambers expansion reservoir

appr. 10

appr. 2.6

Swing gearbox (Gearbox P/N 3692960)

3 x appr. 38

3 x appr. 10

Swing gearbox (Gearbox P/N 3676892) - Brake chambers Travel gearbox - Pre-chambers / spur gear section

3 x appr. 26 3 x appr. 6 2 x appr. 80 2 x appr. 10

2 x appr. 6.9 2 x appr. 1.6 2 x appr. 21.1 2 x appr. 2.6

- Hydraulic motor chambers On-board crane (optional) - Crane drive engine

4 x appr. 0,3

4 x appr. 0.08

approx. 5,5

approx. 1.45

- Hydraulic oil reservoir

approx. 50

approx. 13.2

II III.a III.a III.b III.b III.c I II

Filling quantities - other Location

Filling quantity litres

gal

Screen washer

appr. 13

appr. 3.4

Fuel tank, crane drive engine (optional)

approx. 20

approx. 5.3

3-30

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing LUBRICANTS Notes on the selection of oils and greases Original Bucyrus HEX oils and greases Besides regular and careful maintenance, the quality of the oils and greases used in the machine has a decisive influence on high performance, reliability and long service life of a machine and of its units and assemblies.

The lubricants tables in the Bucyrus HEX Operating Instructions contain specifications for the oils and greases that are approved for use in Bucyrus HEX machines. These oils and greases are especially adapted to Bucyrus HEX machines and their units and assemblies.

Other oils and greases which do not fulfil the requirements of the specifications can be the cause of premature wear or of damage to and failures of machine units and assemblies.

For this reason, Bucyrus HEX only approves the use of the specified oils and greases.

All other qualities are not approved.

Alternative oils and greases The oils and greases filled into the machine must meet at least the specifications mentioned in the lubricants tables of the Bucyrus HEX Operating Instructions.

In the event of damage to the machine or to its units and assemblies caused by the use of alternative oils and greases that are not compatible with Bucyrus HEX specifications, Bucyrus HEX does not assume any responsibility and does not accept any warranty claims.

Avoid mixing of different hydraulic fluids The machine has been run in at the factory with BM Long Term Hydraulic Fluid HSS (Part-No. 2482971). Bucyrus HEX recommends using this high-grade hydraulic fluid also in operation as it has been made especially for use in these machines to which it is also perfectly adapted.

If oil analyses are performed regularly and with positive results, the BM Long Term Hydraulic Fluid can remain in the machine for up to 10 000 operating hours.

If an alternative hydraulic fluid is to be used, it must fulfil the same specifications. Please note that the change interval for alternative fluids is fixed at 5 000 operating hours.

There is an increased risk of damage to hydraulic components, if different hydraulic fluids are mixed during topping up as well as when changing over to a fluid of a different type or from another manufacturer.

For topping up, it is therefore necessary to use only same hydraulic fluid as the one that is already in the hydraulic system.

When changing over to an alternative hydraulic fluid, please observe that there is always a small amount of old fluid remaining in the hydraulic system even after the system has been emptied. The mixing of this residual amount of old fluid with the new alternative fluid reduces the properties of the fluid dramatically and can cause damage to components of the hydraulic system in operation.

To avoid this result, the change-over to the alternative fluid must be performed in strict compliance with the manufacturer's prescriptions. The manufacturer must confirm that his hydraulic fluid is compatible with the BM Long Term Hydraulic Fluid.

The remaining amount of old fluid must not exceed 2% of the total volume. This can only be achieved by repeated flushing with the total fluid volume.

If the remaining amount of fluid exceeds 2% of the total volume, the fluid becomes a detrimental "mixed fluid".

The operation of the system with mixed fluids must by all means be avoided.

Bucyrus HEX assumes no warranty for damage caused as a result of the machine having been operated with consumables of inappropriate specification or with mixed fluids.

BA RH170B(3 725 013.00)-EN

3-31

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing

I.

Oils for combustion engines (On-Board Crane, optional)

Fig. 3-9:

3-32

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing

II.

Oil for hydraulic system

Fig. 3-10:

BA RH170B(3 725 013.00)-EN

3-33

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing

III.a Oils for pump gearbox

Fig. 3-11:

3-34

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing

III.b Oils for swing gearboxes

Fig. 3-12:

BA RH170B(3 725 013.00)-EN

3-35

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing

III.c Oils for travel gearboxes

Fig. 3-13:

3-36

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing

V.

Greases for bearings and slewing rings

Fig. 3-14:

BA RH170B(3 725 013.00)-EN

3-37

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing SERVICING WORK Hose line for oil change Collect escaping oil and cooling liquid and discard without polluting the environment.

The swing gearboxes are moreover equipped with automatic drain valves (1, Fig. 3-16:) These automatic drain valves permit oil changes without polluting the environment.

Carry out oil changes when the machine is at operating temperature; warm oil drains away more easily.

Filling and draining is can be done by means of a hose through the service station (tanklift) (Fig. 3-15:).

For filling and draining, a flexible hose is connected to the express coupling on the service station and to the service vehicle at the other end.

The filling operations require an overpressure, whereas the draining operations require low pressure.

Fig. 3-16:

Change oil as follows:  Place a collecting recipient for used oil under the corresponding automatic drain valve. For the recipient capacity refer to the "Re-filling quantities - Oil" table or to the "Refilling quantities - Other" table.  Unscrew protective cap from automatic drain valve.  Screw on hose line (2) to open the valve, so that the oil or the cooling liquid can flow out.  When the oil has drained away, unscrew hose line to allow the valve to close automatically.  Screw protective cap back in place.

Fig. 3-15:

3-38

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing ELECTRIC MOTOR Electric motor - Safety instructions

Cleaning the electric motor When cleaning with compressed air deposited dust and loose parts can be whirled up and may cause injuries.

Read and observe: "Inspection and Servicing – Safety Instructions" and the electric motor operating instructions.

Always wear your personal protection equipment like protective suit, goggles, respiratory protection, gloves etc.

Use a vacuum cleaner to extract dust.

Secure the machine as described in the "Securing the machine" section.

Wear protective gloves and firm working clothing.  Switch off electric motor, to do so actuate switch (52, Fig. 3-17:).

Clean the electric motor, the cooling fins, bearing shields and ventilators from dust with compressed air, brushes and clothes only.

 Set servicing switch (4, Fig. 3-18:) to locked position and secure in this position with a padlock.

Remove the fan guard before cleaning the ventilator fan. Install it after cleaning.

Don't damage the protective coating while cleaning the electric-motor.

For more information see the manufacturers manual for the electric motor.

It is not permissible to clean the electric motor or any live excavator components with a steam cleaner and steam jet.  After finishing work on the electric motor remove the padlock from servicing switch (4, Fig. 3-18:) and unlock.

Fig. 3-17:

Fig. 3-18:

BA RH170B(3 725 013.00)-EN

3-39

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing Electric motor, greasing Read and observe: "Inspection and Servicing – Safety Instructions" and the electric motor operating and maintenance instructions.

Secure the machine as described in the "Securing the machine" section.

Wear protective gloves and firm working clothing.

During greasing the electric motor must be switched on. Be extremely careful to rotating parts.

Grease chambers at the bearings of the electric motor can carry only a limited amount of used grease.

Check grease chambers before pressing in fresh grease and remove used grease if necessary.

Grease the bearings of the electric motor in regular intervals (see plate on the electric motor for more detailed instruction about greasing procedure).  Press in grease into the grease nipples located at the end shields at the electric motor. The grease nipples are located at the motor housing away from the bearings.  When the electric motor is at standstill, remove the old, used grease from the bearing housing.

Additional information on servicing the electric motor is given in the electric motor operating and maintenance instructions given from the motor manufacturer.

Up to 30 minutes after greasing the temperature of the bearings might heavily increase. Thereafter the temperature decrease to normal. This is normal, the procedure is monitored on the BCS display.

Additional servicing work All servicing and maintenance work not described here are carried out by the Bucyrus HEX after sales service resp. by the Service Dept. of the manufacturer of the electric motor. (see electric motor operating and maintenance instructions).

3-40

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing ELECTRICAL SYSTEM Electrical system - Safety instructions

Interrupt electrical circuits with the circuit breaker before start working on the electrical system. All electric lines upwards from the circuit breaker are then without voltage (refer to the "Safety instructions for excavators with electric motor" at the beginning of this chapter).

Read and observe the "Inspection and servicing – Safety instructions" chapter.

Risk of injury caused by battery acid and gases.

Before starting live-line servicing work e.g. measuring and testing with voltage applied, press switch (4, Fig. 3-19:) and secure it with a padlock.

Now voltage is supplied to the whole system but the electric motor can not be switched on.

This prevents accidents, inadvertent starting of the electric motor, and short circuits.

Wear goggles, working gloves and firm working clothing.

Carry out voltage and continuity checks only by means of a test lamp or a measuring instrument.

Do not check by "touching ground" with a bare wire. The short-circuit thus produced damages the alternator and the electronic modules of the PMS. The electrical circuit diagrams are annexed to the spare-parts list. Further information can be found in the Bucyrus HEX Technical Handbook "Working with circuit diagrams".

The 24V circuits are energized by the two batteries when the circuit breaker is switched off. These lines can also be de-energized with the battery main switch. Shut off the electrical system with the battery main switch when carrying out repair work or during prolonged downtimes of the excavator.

Cables and cable lugs must not get in contact with other metal parts. Replace broken or damaged cables and the respective cable lugs.

If a bulb does not work after replacement, the pertaining fuses, connection cables and contacts must be checked.

Gas-discharge lamps in Xenon working lights are operated with high voltage.

Fig. 3-19:

BA RH170B(3 725 013.00)-EN

3-41

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing Battery Warning Battery Posts, terminals and related accessories contain lead and lead compounds, chemicals known to cause cancer and reproductive harm.

Wash hands after handling.

Checking the battery fluid level (Not applicable in case of maintenance-free batteries)  Unscrew caps (Fig. 3-20:).  If checking inserts are provided, the battery acid must reach up to their bottom.  If no checking inserts are provided, insert a clean wooden rod into the battery until it contacts the upper edge of the cell plates. The rod must be moistened over at least 10 mm (0.4“).  If the fluid level is too low, top up with distilled water only

Checking the charge condition of the battery The acid temperature must be 20 ° C (68°F).  Unscrew caps of the battery (Fig. 3-20:).  Measure the acid density of the battery using a commercial acid tester (Fig. 3-20:).

The acid density measured is in direct correlation with the battery charge.

Acid density kg / dm3 Charge Normal Tropical conditicondition ons 1,28 1,23 fully charged 1,20 1,12 half charged, recharge 1,12 1,08 discharged, recharge immediately

Charging the batteries The batteries are charged by the battery charger only if the electrical system with the circuit breaker is switched on.

The battery main switch must be in position I "ON".

Fig. 3-20:

3-42

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing Battery main switch, switching on and off When the excavator is disconnected from the medium voltage (7.2kV) the electrical system (24V) is supplied with voltage by two batteries.

With the battery main switch, the electrical system (24V) is disconnected from the batteries.

The battery main switch is located at the right side wall of the control cabinet (24V). The control cabinet (24V) is mounted in the driver's cab module beneath the driver's cab.

Switching the battery main switch on  Insert switching handle into battery main switch (position "0", Fig. 3-21:) and turn it to position "I".

Fig. 3-21:

Switching the battery main switch off  Turn switching handle from position "I", Fig. 3-21: to position "0" and withdraw.

BA RH170B(3 725 013.00)-EN

3-43

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing Removing and installing the battery Read and observe the "Inspection and servicing – Safety instructions" chapter.

Wear protective gloves and firm working clothing.

Switch off the electric motor before removing the batteries.

 Turn key in key-switch in the control column to position "0" and withdraw.  Set battery main switch (Fig. 3-21:) to “OFF“ position.  Disconnect and reconnect the terminal clamping lugs in the prescribed order.

Disconnecting and connecting in the wrong order may cause short-circuits.

The batteries (1, Fig. 3-22:) are located in the cab module underneath the drivers cab.

 Detach battery holder (3).

The 12-volt batteries are connected in series and in parallel, so that the system voltage is 24 volts.

 Disconnect the cable lug from the negative terminal of the battery.  Disconnect the cable lug from the positive terminal of the battery.  Insulate the cable lugs.  Lift battery out of battery box.

Before installing new batteries, the contact faces of the battery terminal posts and the cable lugs must be cleaned down to the bright metal.  Install the new batteries.  Connect the cable lug to the positive terminal of the battery. Tighten the clamping screws of the cable lugs. Do not use too much force to avoid deformation.

Fig. 3-22:

 Connect the cable lug to the negative terminal of the battery.  Apply special terminal grease or acid-free vaseline on the battery terminal posts and clamping lugs. Loose or corroded clamping lugs will lead to battery charger overloading.

3-44

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing Switchgear cabinet Breather filter Breather filters are located in the switchgear cabinets:  For the 7.2 kV power supply (2, Fig. 3-23:), 

For the 400 V system (1, Fig. 3-23:),



For the 24 V system (3, Fig. 3-24:).

The air is drawn in and cleaned by a ventilator with air filter.

Fig. 3-23:

Fig. 3-24:

BA RH170B(3 725 013.00)-EN

3-45

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing Emptying dust trap  Press dust trap (14, Fig. 3-25:) and hold until the dust trap is empty.

Emptying the dust collector  Loosen clips (11, Fig. 3-25:).  Remove dust collector (12) and empty.

Filter element, replace  Remove dust collector (12, Fig. 3-25:).  Withdraw filter element (13, Fig. 3-26:).  Replace or clean filter element (13).

Fig. 3-25:

 Refit dust collector (12, Fig. 3-25:).

Fig. 3-26:

3-46

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing Checking and cleaning the filter element Check the filter paper of the element by inserting a lamp into the element (Fig. 3-27:). Any damage can then be seen.

Replace damaged or distorted element immediately.

Check element seal. If damaged, replace filter element too.

Cleaning with compressed air allows the filter element to be re-used immediately.

Blow filter element (Fig. 3-28:) dry with compressed air by moving the compressed-air piston up and down inside it.

Fig. 3-27:

The pressure at the nozzle must not exceed 3 bars (43 psi).

Cleaning is completed when no more dust is seen to leave the filter element.

Never clean filter element by beating it against hard objects.

Replace main filter element after 1000 operating hours or 3 cleaning cycles, but not later than after one year of operation.

Fig. 3-28:

BA RH170B(3 725 013.00)-EN

3-47

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing Replacing filter mats

Slip ring maintenance

A filter mat is installed in the switchgear cabinet (Fig. 3-29:) behind the cover (4).

See (Fig. 3-30:) High tension, Danger to Life.

Check filter mats visually and replace if necessary.

Switch off power supply at the transformer station.

Check that the slip ring assembly is without tension before opening it.

Read and observe the "Inspection and servicing – Safety instructions" chapter as well as the chapter “Electrical system, safety instructions”.

Observe the Servicing Instructions of the slip ring manufacturer.  Remove all tracks of dirt.

Fig. 3-29:

Drain condensate from the switch gear cabinets  Check all cabinets for condensate.  Screw out draining plugs and drain condensate.

Keep the inner of the cabinets dry and clean.

 There is a transparent sideplate at the housing. Check the housing inside for wear debris coming from the brushes and for grease. Remove if necessary.  Clean insulators and check for damage.  Check condition of slip ring contact surfaces; remove any sign of oxydation, "splatter" or burn spots.

Then coat with contact grease.  Check carbon brushes for signs of wear.

(See Servicing Instructions of the slip ring manufacturer).

Fig. 3-30:

3-48

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing Floodlight projector, replacing the lamp Safety instructions The floodlight projectors use xenon technology.

The lamp is not a usual incandescent lamp, but a gas discharge lamp which is operated with a ballast unit. The ballast unit is integrated in the floodlight projector.

When the projector is turned on, the ballast unit generates a high-voltage pulse of more than 25000 volts to start the xenon lamp.

Warning!

This high-voltage pulse can be a lifethreatening risk, if a person comes into contact with any of the live components. This can be the case, for instance,  if the lamp is operated improperly,  

if the projector housing is opened in an inapropriate way or by sticking one's hand into an opened or damaged projector.

Protect yourself from potential risks by reading and by observing the following safety instructions.

Always switch off the projector and disconnect it from its power supply before replacing the Xenon lamp.

Allow the xenon lamp to cool off before removing it from the projector.

Wear googles and safety gloves when replacing the lamp.

Never stick your hand into the lampholder. The contacts may still be live with residual voltage.

Never switch on the projector when the xenon lamp has been removed.

There is a risk of voltage discharge and damage to the lampholder.

The glass body of the xenon lamp is filled with different gases and metal gases and is under gauge pressure (risk of injury from splinters) If the xenon lamp breaks apart in closed room (workshop), all persons must leave the room and the room must be ventilated for at least 20 minutes to exclude any health risks caused by gases.

Further instructions Always hold the xenon lamp by the base. Never touch the glass bulb. Sweat and grease from the skin would evaporate when the lamp is in operation and obscure the reflector.

If the fingers have nevertheless come into contact with the glass bulb, the fingerprints must be removed with a clean cloth and some alcohol.

The replaced Xenon lamp must be disposed of as special waste.

Never switch on projectors when housing or electrical wiring is damaged.

Have damaged projectors be replaced by a qualified electrician as soon as possible.

BA RH170B(3 725 013.00)-EN

3-49

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing Replacing a defective Xenon-lamp Read and observe the: „Floodlight projector, replacing the lamp, Safety instructions“.  Switch off the projector, shut off the electric motor and cut out the battery main switch.  Wait until the housing of the floodlight projector has cooled down.  Withdraw the power supply connector from the projector.

Fig. 3-31

 Remove four screws (1, Fig. 3-31) and withdraw the reflector (2) from the projector housing.  Withdraw connector (Fig. 3-32) from Xenon lamp socket.  Unscrew Xenon lamp holding clamp (Fig. 3-33).  Remove the defective Xenon lamp and replace by a new one. Do not touch the glass bulb of the lamp.  Reinstall the new lamp. Screw lamp holding clamp back in place.  Plug the power supply connector onto the lamp.  Re-assemble the housing.

Fig. 3-32

Fig. 3-33

3-50

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing HYDRAULIC SYSTEM Hydraulic system - Safety instructions Read and observe the "Inspection and servicing – Safety instructions" chapter.

Before working on the hydraulic system, make sure that the system is without pressure and that the residual pressures have also been eliminated.

Switch off the electric motor.

Risk of burning caused by hot hydraulic components (e.g. hydraulic oil reservoir, cylinder, valves).

Depressurizing the hydraulic system Hydraulic systems may only be opened if they are completely depressurized. Even when an excavator is parked on a horizontal surface with the working equipment resting on the ground (Fig. 3-34: / Fig. 3-35:) and with its electric motor switched off, there may still be a considerable amount of residual pressure in parts of the hydraulic system, as e.g. the primary pressure resulting from the last hydraulic movements before the immobilization.

Residual pressures disappear only gradually. If work is to be carried out on the hydraulic system immediately after the immobilization, the system must be freed from pressure, i.e. depressurized:

Secure the machine as described in the "Securing the mmachine section.

Avoid skin contact with hydraulic oil.

Contact with hydraulic oil can cause skin injury.

Wear protective gloves and firm working clothing.

Fig. 3-34:

 Locate the system section to be opened.  Depressurize the section to be opened. If required, the necessary measures described must be combined  Open the depressurized system section with caution.

Fig. 3-35:

BA RH170B(3 725 013.00)-EN

3-51

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing Examples of system sections:

Checking the hydraulic oil level

1) working hydraulics,

 Bring hydraulic oil to operating temperature (abt. 50 °C / 122°F).

2) servo control circuit, 3) precharged return-flow line.

Depressurizing:  Park the excavator on a horizontal surface.  Set the working equipment on the ground.  Switch off the electric motor.

 Park the machine on a horizontal surface.  Bring the working equipment to a stretched out position and put it on the ground (Fig. 3-39:).

The oil level must lie between the “min” and the “max” marks of signs (2) near the inspection glass (1, Fig. 3-37:).

 Do not switch off the electrical system For sections 1 and 2, servo control and working hydraulics:  Shift both control levers repeatedly into all dIrections (Fig. 3-36:).

For section 3, return-flow line: After switching off the electric motor, the precharging pressure decreases rapidly through the precharging valve. No measures are required before opening the return-flow line.

Fig. 3-37:

The hydraulic oil level is monitored by the BCS. The BCS displays a warning on the screen (Fig. 3-38:) if the hydraulic oil level is too low or too high.

Switch off the electric motor, locate cause and rectify.

Fig. 3-36:

Fig. 3-38:

3-52

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing

Fig. 3-41:

Fig. 3-39:

Fill in hydraulic oil through the return-flow filters:  Stand working equipment on the ground as shown on the sign (Fig. 3-39:).

Sign (2, Fig. 3-40:) is attached beside the level inspection glass (1).

Hydraulic oil can also be filled inby means of the service station (Fig. 3-42:).  Unscrew cap of express coupling (10).

Connect filling hose express coupling of the service vehicle.

The use of the hose line is described in the "Hose line for oil change" section.  Fill in hydraulic oil until the oil level lies between the “min” and the “max” marks of the sign near the inspection glass (1, Fig. 3-40:) (oil grade cf. "LUBRICANTS").  Unscrew the hose line; the express coupling closes automatically.  Screw protective cap back in place

Fig. 3-40:

 Remove cover (19, Fig. 3-41:). abnehmen.  Fill in hydraulic oil through the opening until the oil level lies between the “min” and the “max” marks of sign (2) near the inspection glass (oil grade cf. "LUBRICANTS").

Fig. 3-42:

 Before fitting the cover (19), check the sealing ring and replace, if damaged.  Fit cover together with sealing ring.

BA RH170B(3 725 013.00)-EN

3-53

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing Replacing the hydraulic oil return-flow filters (hydraulic oil reservoir) Read and observe the "Inspection and servicing – Safety instructions" chapter.

Switch off the electric motor.

The return-flow filters must be replaced: 

when servicing works in accordance with the servicing plan are carried out;



when the BCS displays a warning on the screen (Fig. 3-43:). In this case, the filter elements (9, Fig. 3-44:) are heavily contaminated;



after repairs on the hydraulic system;



in case of damage.

Risk of scalding caused by hot hydraulic oil.

The hydraulic oil reservoir itself may also be hot.

Avoid skin contact.

Skin contact with hydraulic oil may cause skin injury.

Wear protective gloves and firm working clothing.

Collect escaping hydraulic oil and discard without polluting the environment.

Fig. 3-43:

 Remove cover (3, Fig. 3-44:) together with sealing ring (5) and retaining disk (7).  Remove cap (8, Fig. 3-44:) and sealing ring (10).  Withdraw filter element (9) and sealing ring (11) from basket (12).  Insert a new filter element.

If a filter element (9) is damaged, remove basket (12) and check/clean.

Fig. 3-44:

3-54

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing  Loosen screws (13, Fig. 3-45:) and take off spring clip (14) and disk (15).

If metal filings are detected, locate cause and rectify.

 Remove basket (12) and clean in paraffin oil.

Contact the Bucyrus HEX Service, if required.

 Install basket (12).  Insert filter element (9) together with sealing ring (11) and cap (8) with sealing ring (10).  Refit cover (3).  Clean the magnetic rod The magnetic rod is located under cap (19).

Fig. 3-45:

BA RH170B(3 725 013.00)-EN

3-55

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing Bypass valves (hydraulic oil reservoir)

Cleaning the filter screens

Read and observe the "Inspection and servicing – Safety instructions" chapter.

Switch off the electric motor.

Risk of scalding caused by hot hydraulic oil.

The hydraulic oil reservoir itself may also be hot.

Avoid skin contact.

Skin contact with hydraulic oil may cause skin injury.

Wear protective gloves and firm working clothing.

Fig. 3-47:

Collect escaping hydraulic oil and discard without polluting the environment.

 Remove cover (3, Fig. 3-47:) together with sealing ring. Unscrew screws (25). Withdraw bypass valve. Take off screen (21) together with sealing ring and clean in white spirit or paraffin oil. Replace, if required.

Check sealing ring for damage and replace, if required.

Re-assemble the bypass valve.  Check sealing ring (28) for damage and replace, if required.  Insert bypass valve and fasten with screws (25).

Fig. 3-46:

Replacing the bypass valves and sealing rings  Remove bypass valve as described under "Cleaning the screens".  Re-assemble the bypass valve with a new screen (21, Fig. 3-47:) and a new sealing ring.  Insert bypass valve with new sealing ring (243) and fasten with screws (25).

3-56

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing Breather filter, replace Read and observe the "Inspection and servicing - Safety instructions" chapter.

Replacing the filter elements The breather filters (20, Fig. 3-48:) ensure venting of the hydraulic oil reservoir at varying hydraulic oil levels.

Switch off the electric motor.

Risk of scalding caused by hot hydraulic oil.

The hydraulic oil reservoir itself may also be hot.

Avoid skin contact.

Skin contact with hydraulic oil may cause skin injury.

Wear protective gloves and firm working clothing.

Fig. 3-48:

 Unscrew screws (21). Remove holder (22) and withdraw filter element (20).  Check filter element and replace, if required.

BA RH170B(3 725 013.00)-EN

3-57

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing Filter (control circuit) Read and observe the "Inspection and servicing - Safety instructions" chapter.

Replacing the filter elements To filter the hydraulic oil in the control circuit, the machine is equipped with a high-pressure filter (Fig. 3-49: and 8, Fig. 3-50:).

Change filter element regulary and when the BCS indicates a contamination.

Switch off the electric motor.

Risk of scalding caused by hot hydraulic oil.

The hydraulic oil reservoir itself may also be hot.

Avoid skin contact.

Skin contact with hydraulic oil may cause skin injury.

Wear protective gloves and firm working clothing.

Fig. 3-50:

 Unscrew filter housing (5, Fig. 3-50:).  Withdraw filter element (6) from filter housing (5).  Clean filter housing (5) and the sealing face at the filter head (9) with white spirit or paraffin oil.

Fig. 3-49:

 Check seals (10 and 14) and replace, if required.  Insert new filter element into filter housing (5) and refit to the filter head with new, lightly oiled sealing ring (8).  Check for leaks after putting the filter into operation.

3-58

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing High-pressure filter for working hydraulics To filter the hydraulic oil on the high-pressure side of the working hydraulic system, the machine is equipped with four high-pressure filters (8, Fig. 3-51:).

Checking/cleaning the filter elements  Unscrew drain plug (11, Fig. 3-52:) and drain the hydraulic oil from the filter housing (9).

(Place a suitable resipient under the filter housing).  Unscrew filter housing (9).  Disengage filter element (15) with a slight turn from ist retaining catch and withdraw from filter housing (9).  Clean filter element (15) in white spirit or paraffin oil.  Replace filter element (15) if it is damaged.  Check seals (10 and 14) and replace, if required.  Re-assemble the filter element in reverse order.  Check for leaks after putting the filter into operation.

Fig. 3-51:

Read and observe the "Inspection and servicing – Safety instructions" chapter.

Switch off the electric motor.

Risk of scalding caused by hot hydraulic oil.

The filter housings themselves may also be hot.

Avoid skin contact.

Skin contact with hydraulic oil may cause skin injury.

Wear protective gloves and firm working clothing.

Collect escaping hydraulic oil and discard without polluting the environment.

Fig. 3-52:

Replacing the filter elements  Detach the filter element as described under "Checking the filter elements".  Clean filter housing (9, Fig. 3-52:) and the sealing faces at the filter head with white spirit or paraffin oil.  Insert new filter element into filter housing (9) and refit to the filter head with new, lightly oiled sealing rings (10 and 14) and a new retaining ring (13).

Check high-pressure filter for leaks after putting it into operation.

BA RH170B(3 725 013.00)-EN

3-59

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing High-pressure filters for the servo circuit

Checking/replacing the filter elements

The servo circuit is equipped with two highpressure filters (Fig. 3-53:).

 Remove filter housings and pour out used oil.

The filters are located at the hydraulic oil reservoir.

Read and observe: "Inspection and servicing - Safety instructions".

 Loosen flange (4, Fig. 3-54).

 Withdraw filter element (6) from filter housing (5).  Clean filter housings and sealing faces at filter head with white spirit or paraffin oil.  Insert new filter element (6) together with new sealing ring (7) into filter housing (5) and refit to filter head with a new, lightly oiled sealing ring (8).

Check the high-pressure filter for leaks after putting it into operation.

Fig. 3-53:

Shut off the electric motor.

Risk of scalding from hot hydraulic oil.

The filter housings may also be hot.

Avoid skin contact.

Skin contact with hydraulic oil may cause skin injury.

Wear protective gloves and firm protective clothing.

Collect escaping hydraulic oil and discard without polluting the environment.

Fig. 3-54

3-60

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing High-pressure filters for swinging circuits

Checking/cleaning the filter element

The excavator has three high-pressure filters (Fig. 3-55:) for the swinging circuits. The high-pressure filters are installed at the hydraulic oil reservoir .

 Remove filter housings and pour out used oil.

Read and observe: "Inspection and servicing - Safety instructions".

 Detach flange (4, Fig. 3-56:).

 Withdraw filter element (6) from filter housing (5).  Clean filter housings and sealing faces at filter head with white spirit or paraffin oil.  Insert new filter element (6) together with new sealing ring (7) into filter housing (5) and refit to filter head with a new, lightly oiled sealing ring (8).

Check the high-pressure filter for leaks after putting it into operation.

Fig. 3-55:

Shut off the electric motor.

Risk of scalding from hot hydraulic oil.

The filter housings may also be hot.

Avoid skin contact.

Skin contact with hydraulic oil may cause skin injury.

Wear protective gloves and firm protective clothing.

Collect escaping hydraulic oil and discard without polluting the environment.

Fig. 3-56:

BA RH170B(3 725 013.00)-EN

3-61

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing Changing the hydraulic oil Read and observe the "Inspection and servicing - Safety instructions" chapter.

Switch off the electric motor.

Drawing off hydaulic oil The hydraulic oil can be drawn off by means of the service station (Fig. 3-57:).  Bring hydraulic oil to operating temperature (ca. 50° C / 122°F).  Bring the working equipment to a stretched out position and put it on the ground.

Risk of scalding caused by hot hydraulic oil.

The hydraulic oil reservoir itself may also be hot.

 Switch off the electric motor.

Avoid skin contact.

 Unscrew cap of express coupling (10).

Skin contact with hydraulic oil may cause skin injury.

Wear protective gloves and firm working clothing.

 Connect hose line of the service vehicle.

The hose line and its use are described in the "Hose line for oil change" section.

Collect escaping oil and discard without polluting the environment.

 Draw off hydraulic oil.

(Information about the selection of hydraulic fluids can be found in section “LUBRICANTS”).

 Remove hose line. The coupling closes automatically.

Do not switch on the electric motor when the hydraulic oil reservoir is empty. The hydraulic pumps may be destroyed if they are allowed to run dry.

 Screw on protective cap.

Fig. 3-57:

3-62

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing Cleaning the hydraulic oil reservoir Explosion hazard.

 Drain off hydraulic oil as described under "Drawing off hydraulic oil".

Do not use white spirit, paraffin oil or other solvents for cleaning.

 Remove cap (3, Fig. 3-58:).

Use diesel fuel or a special flushing oil.

Read and observe the "Inspection and servicing - Safety instructions" chapter.

 Detach the return-flow filter.  Place a collecting recipient for the flushing oil under the hydraulic oil reservoir.

Switch off the electric motor.

 Clean the inside of the hydraulic oil reservoir with diesel fuel or flushing oil.

Remove all sediments and also the residues of the cleaning agent thoroughly.

Skin contact with hydraulic oil may cause skin injury.

 Refit cap (3).

Avoid skin contact.

Wear protective gloves and firm working clothing.

Dispose of contaminated hydraulic oil without polluting the environment and separately from other waste.

Fig. 3-58:

BA RH170B(3 725 013.00)-EN

3-63

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing Filling in hydraulic oil Fill in hydraulic oil by means of the service station (Fig. 3-59:).  Unscrew cap of express coupling (10, Fig. 3-59:).  Connect filling hose express coupling from the service vehicle.

The use of the hose line is described under "Hose line for oil change".

 Vent the hydraulic system.  Check the oil level in the hydraulic oil reservoir. Top up with oil, if required.  Unscrew the hose line. The express coupling closes automatically.  Screw protective cap back in place.

 Fill in hydraulic oil until the oil level lies between the “min” and the “max” marks of the sign (2) near the inspection glass (1, Fig. 3-60:).

(Oil grade cf. "LUBRICANTS").  The oil level is also displayed on the BCSscreen (Fig. 3-61:).

Fig. 3-61:

Fig. 3-59:

Fig. 3-60:

3-64

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing Topping up with hydraulic oil Hydraulic oil can be topped up through the returnflow filters.  Remove cap (19, Fig. 3-62:).  Fill in hydraulic oil through the opening until the oil level lies between the “min” and the “max” marks of the decal (2) beside the inspection glass (1, Fig. 3-63:). (oil grade see: "LUBRICANTS").  Vent the hydraulic system.  Check the oil level in the hydraulic oil reservoir. Top up with oil, if required.  Refit cap (19, Fig. 3-62:).

Fig. 3-62:

Fig. 3-63:

BA RH170B(3 725 013.00)-EN

3-65

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing Venting the hydraulic system Hydraulic pumps, hydraulic motors, hydraulic cylinders, travel brake valves, suction lines of hydraulic pumps, oil cooler manifolds and the servo control system must be vented  after assembly on site and prior to initial commissioning, 

before each recommissioning of the excavator, e.g. after extensive repair work to the hydraulic system or after prolonged downtimes,



after each hydraulic oil change,



after replacement of hoses or lines.

Venting the hydraulic components 

Hydraulic pumps and hydraulic motors (with electric motors shut off).

Fig. 3-65:

Always admit oil first to that side of the cylinder where the piston (2) is. This is

Open the highest leakage oil port and fill in clean hydraulic oil up to the lower edge of the opening.

• the piston-side port (3) when the piston rod is retracted (1, Fig. 3-64:), • the rod-side port (4) when the piston rod is extended (1, Fig. 3-65:).

Check the hydraulic system under load. Pay attention to noises produced by the hydraulic pump or the hydraulic motors. Abrupt movements of the working equipment are a sign of entrapped air in the system. Remaining air pockets can be eliminated by actuating all hydraulic functions. 

If, for assembly reasons, the piston rod is inmiddle position, admit oil first to the piston-side port (4).

When oil is admitted for the first time to the cylinder, the oil flow must be reduced. Therefore extend or retract the piston rod as slowly as possible.

Hydraulic cylinder Before the initial admission of the cylinder with oil, the piston must be in either of the two extreme piston positions. In other words, the piston rod (1, Fig. 3-64: and Fig. 3-65:) must be either completely retracted or completely extended.

The screws/nozzles of the following components must be opened until oil emerges bubble-free from the opening: Always vent only the system section that has been opened.



the travel brake valve at the venting screw,



the oil cooler manifold at the mini-measuring ports,



the servo system at the venting screws of the control blocks (under the servo caps),



the intake line at the venting screw (with drive motors stationary).

Fig. 3-64:

3-66

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing Cleaning the hydraulic oil cooler Risk of injury from rotating cooler fan blades.

Cleaning The hydraulic oil coolers are located in the oil cooler module.

Clean the hydraulic oil coolers at regular intervals.  Switch off the electric motor

Switch off the electric motor.

 Remove any accumulated dirt.

Never start cleaning work until the cooler fan blades have stopped turning.

 Clean the fan blades (2, Fig. 3-66:).

The hydraulic oil coolers reach the same temperature as the hydraulic oil. Risk of burning.

 Clean the radiators with a jet of water or compressed air from outside to inside.

Allow the hydraulic oil cooler to cool down.

Wear protective gloves and firm protective clothing.

If the machine is used in places with heavily contaminated ambient air, the hydraulic oil coolers must be cleaned more often than specified in the servicing plan.

 Leave hydraulic oil coolers to dry.  Check the hydraulic motors (1) for free movement.

In winter-time, check that the fans (2) turn freely and that the cooling fins are free from ice and snow.

The speeds of the fan motors (1, Fig. 3-66:) are thermostat-controlled. The fan motors run at maximum speed when the hydraulic oil temperature reaches ca. 60°C / 140°F.

Fig. 3-66:

BA RH170B(3 725 013.00)-EN

3-67

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing Electronic excavator control Joystick At regular intervals acc. to the maintenance plans:  Loosen gaiter and move upwards.  Apply a thin layer of low temperature grease on the control spools, the actuator plate above and the cardan joint of the joysticks (arrows, Fig. 3-67:) to prevent jamming of the joysticks.

Pedal At regular intervals acc. to the maintenance plans:  Remove old grease and dirt from the control spools and the actuator plate of the pedals (arrows, Fig. 3-68:).  Apply a thin layer of low temperature grease on the control spools of the pedals to prevent jamming of the control spools.

 Refit gaiter using a cable strap.

Fig. 3-68:

Fig. 3-67:

3-68

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing Pressure accumulator - Emergency lowering To permit the working equipment to be lowered in an emergency, the machine is equipped with a pressure accumulator (2,Fig. 3-69:).

The pressure accumulator (2) is located in the superstructure and is accessible from the ground.

Extract from the German acceptance regulations Hydraulic accumulators are pressure vessels and are therefore subject to the "Druckbehälterverordnung (DruckbehV)" [Pressure Vessel Regulations].

Their installation, equipment and operation are governed by the "Technische Regeln Druckbehälter (TRB)" [Technical Rules for Pressure Vessels]. The pressure vessels of hydraulic accumulators are classified by the admissible operating pressure p in bars, the capacity l in liters and the product of pressure and capacity p x l. Depending on the class to which the accumulator belongs, the following inspections are mandatory: Checking the gas charging pressure in the pressure accumulator

Fig. 3-69:

Pressure-accumulator inspection regulations The following regulations are applicable only in Germany. Please observe the relevant regulations in force in your own country.

After commissioning (new installation or repair), the gas charging pressure in the pressure vessel must be checked at least once during the first week. If no pressure loss is detected, the second pressure test must be performed after ca. 3 months. If no pressure loss is detected in this test either, the testing interval can be fixed at once pressure test each year.

For measuring the precharge pressure in the pressure accumulator, observe the instructions set out in the booklet "Filling and testing device for pressure accumulators" annexed to this documentation

Extract from the German regulations The accumulator vessel must not be subjected to welding, soldering or any other mechanical work.

Work on systems containing accumulators (repairs, connection of pressure gauges or similar work) may be carried out only when the fluid pressure has been released Group II p ≥ l bar and p·x l ≤ 200

Inspections prior to commissioning at the factory at the place of use Pressure testing Inspection certificate Prototype and pressure test (Check of correctness and certified by the manufacturer correct installation) issued by an expert

BA RH170B(3 725 013.00)-EN

Regular inspections Inspection schedule to be drawn up by end user, based on experience with type of operation and fluid.

3-69

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing PUMP TRANSFER GEARBOX Read and observe: "Inspection and servicing - Safety instructions.

Shut off the electric motor.

Checking the gearbox oil level / Topping up with oil Check oil level when gearbox oil is cold. Checking oil level when gearbox oil is warm may cause incorrect results.

The gearbox housing may be hot, too.

Park the machine as described in the "Securing the machine" section.

Secure the machine as described in the "Securing the machine" section.

 Unscrew dipstick (1, Fig. 3-70: and Fig. 3-71:) and wipe clean.

Protect the skin from contact with gearbox oil.

 Insert dipstick (1) again until the thread lies on top of the dipsticks tube (2, Fig. 3-71:)

Skin contact with cooling liquid is a potential health hazard.

Wear protective gloves and firm working clothing.

 Withdraw dipstick again and check oil level.

Oil level should lie between the two dipstick markers. Top up with gearbox oil if required.

Fig. 3-70:

Fig. 3-71:

3-70

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing Filling in oil  Unscrew breather filter (7, Fig. 3-75:).

Pump transfer gearbox, checking pre chambers oil level

 Fill in fresh gearbox oil through the bore of the breather filter.

(Oil quality see “LUBRICANTS”).

The oil level in all the pre-chambers is visually at the inspection glas (3, Fig. 3-73) in expansion reservoir (1).

 Check oil level.  Screw breather filter back in place.

The oil level should reach up at least to the middle of the inspection glas (3). Top up with gearbox oil, if required through the bore of the breather filter (2).

Fig. 3-72: Fig. 3-73

BA RH170B(3 725 013.00)-EN

3-71

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing Pump transfer gearbox, changing oil Carry out oil change when gearoil is nearly at operating temperature. All suspended particles and contaminations will be rinsed out with the old oil.

Pump transfer gearbox, venting The gearbox is vented through breather valve (7, Fig. 3-75:).

Drawing off oil

Clean breather valve (7) in accordance with the servicing plan.  Unscrew breather filter (7), clean with white spirit or paraffin oil and blow dry with compressed air.

The gearbox oil is drained with the service station (Fig. 3-74:) through express coupling (5). To do so:

 Screw breather filter (7) back in place.

Oil grade see”LUBRICANTS”.

 Unscrew cap of express coupling (5).  Connect hose line of the service vehicle.

The hose line and its use are described in the "Hose line for oil change" section.  Remove hose after the oil has been drawn off.

The coupling closes automatically.  Screw on protective cap.

Filling in oil Fill in oil through express coupling (5, Fig. 3-74:).

To do so:  Unscrew cap of express coupling (5).

Fig. 3-75:

 Connect hose line of the service vehicle.

The hose line and its use are described in the "Hose line for oil change" section.  Fill in gearbox oil, check oil level at dipstick (See: “Checking the gearbox oil level / Topping up with oil”).  Remove hose after the oil has been drawn off.

The coupling closes automatically.  Screw on protective cap.

Fig. 3-74:

3-72

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing Pre-chambers working pumps, draining oil, changing oil

Pre-chambers swing pumps, draining oil, changing oil

Carry out oil change when gearoil is nearly at operating temperature. All suspended particles and contaminations will be rinsed out with the old oil.

Carry out oil change when gearoil is nearly at operating temperature. All suspended particles and contaminations will be rinsed out with the old oil.

Oil grade see”LUBRICANTS”.

Oil grade see”LUBRICANTS”.

Draining oil:

Draining oil:

 Place a suitable receptacle for used oil under the plugs (13, Fig. 3-76:).

The required receptacle capacity is specified in the „Filling quantities – oil“ table.

 Place a suitable receptacle for used oil under the plugs (23, Fig. 3-77:).

The required receptacle capacity is specified in the „Filling quantities – oil“ table.

 Drain oil from the expansion reservoir.

 Drain oil from the expansion reservoir.

 Unscrew plugs (13) and allow oil to drain.

Screw in plugs and fill in oil after repair work has finished.

 Unscrew plugs (23) and allow oil to drain.

Screw in plugs and fill in oil after repair work has finished.

Changing oil:

Changing oil:

 Oil change is necessary only after repairs or after changing a working pump. In this case drain oil and fill in oil as described above.

Oil quantity see „Filling quantities – oil“ table.

 Oil change is necessary only after repairs or after changing a swing pump. In this case drain oil and fill in oil as described above.

Oil quantity see „Filling quantities – oil“ table.

Fig. 3-76:

Fig. 3-77:

BA RH170B(3 725 013.00)-EN

3-73

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing Pump transfer gearbox lube oil filter, replace Check filter tell-tale (1, Fig. 3-78:) regulary - at operating temperature - for indication of contamination.

If the red sector is visible through transparent cap (2), the filter element must be cleaned or changed.  Unscrew filter housing (42, Fig. 3-79:).  Pour oil out of filter housing (42) and remove filter element (43).  Clean filter head and filter housing with white spirit or petroleum.  Place new filter element (43) and new sealing (45) into filter housing and re-assemle with new O-ring (46).

Fig. 3-78:

 Check gearoil filter for leakages after recommencing operation.

If the filter tell-tale (1, Fig. 3-78:) appears, it is possible that the filter is contaminated with metal particles. Inspect the filter element carefully. Trace any cause and remedy.

Fig. 3-79:

3-74

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing SLEWING GEARBOX (For swing gearboxes P/N 3692960) The gearbox housings may be hot, too.

Read and observe: "Inspection and servicing - Safety instructions.

Shut off the electric motor.

Gearbox - Checking the oil level / Topping up with oil  Park the machine as described under "Securing the machine".  Screw out dipstick (1, Fig. 3-80:) and wipe clean.  Insert dipstick (1) fully again (do not screw in) and withdraw a second time.

Secure the machine as described in the "Securing the machine" section.

The oil level must reach up at least to the lower mark on dipstick (1). Top up with gearbox oil, if required.

Protect the skin from contact with gearbox oil.

 Screw dipstick (1) back in place.

Skin contact with cooling liquid is a potential health hazard.

Wear protective gloves and firm working clothing.

Carry out oil change when gearoil is nearly at operating temperature. All suspended particles and contaminations will be rinsed out with the old oil.

Changing the gearbox oil  Prepare a collecting recipient for used oil.

Choose the required capacity in accordance with the "Refilling quantities - Oil" table.

Oil grade see”LUBRICANTS”.

Fig. 3-81:

Fig. 3-80:

Draining off oil  Attach hose (8, Fig. 3-81:) to drain valve (7) and drain off oil completely.

The use of the oil draining hose is described in the "Hose line for oil change" chapter.

The drain valve (7, Fig. 3-81:) is accessible from the undercarriage.  Remove hose. The oil drain valve closes automatically.for oil and cooling liquid change" section.

BA RH170B(3 725 013.00)-EN

3-75

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing Filling in new oil / Topping up

Gearbox venting



The gearbox is vented through breather filter (2, Fig. 3-82:).

Clean breather filter in accordance with the servicing plan.  Unscrew breather filter (2), clean in white spirit or paraffin oil and blow dry with compressed air.

Unscrew plug (4, Fig. 3-82:) and fill in new oil.

 Check oil level with dipstick (1, Fig. 3-82:).  Screw in plug (4) again.

 Screw breather filter (2) back in place.

Fig. 3-82:

3-76

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing SWING GEARBOX (For swing gearbox P/N 3676892) The gearbox housings may be hot, too.

Read and observe: "Inspection and servicing - Safety instructions.

Gearbox - Checking the oil level / Topping up with oil  Check the oil level visually at expansion tanks (5 and 6, Fig. 3-83:). The expansion tanks must be filled with gearbox oil up to abt. 1/3.

The oil level is visible from outside (light/dark area).  If necessary, unscrew cap (7) and fill in oil.

Shut off the electric motor.

Secure the machine as described in the "Securing the machine" section.

Protect the skin from contact with gearbox oil.

Skin contact with cooling liquid is a potential health hazard.

The hoses (4, Fig. 3-83:and Fig. 3-84:) connect the gearboxes (1) with the expansion reservoirs (5 and 6).  Check all threaded joints for leaks.

Wear protective gloves and firm working clothing.

Collect escaping oil carefully and dispose of in an environmentally acceptable manner.

Carry out oil change when gearoil is nearly at operating temperature. All suspended particles and contaminations will be rinsed out with the old oil.

Oil grade see”LUBRICANTS”.

These swing gearboxes have two seperated oil chambers. Each gearbox is connected to two expansion reservoirs for gearoil:  Expansion reservoir for oil in the gearbox housing (5). 

Expansion reservoir for oil in the brake chamber (6).

Fig. 3-84:

Fig. 3-83:

BA RH170B(3 725 013.00)-EN

3-77

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing Changing the gearbox oil Gearbox housing, draining off oil  Prepare a collecting recipient for used oil.

Choose the required capacity in accordance with the "Refilling quantities - Oil" table.  Unscrew caps (7, Fig. 3-87:) from expansion reservoirs (5). Oil will escaping faster then.  Attach hose (3, Fig. 3-85:) to drain valve (2) and drain off oil completely.

The use of the oil draining hose is described in the "Hose line for oil change" chapter.

The drain valve (2, Fig. 3-86:) is accessible from the undercarriage.  Remove oil draining hose. The oil drain valve closes automatically.

Screw on protection cap to the drain valve.

Fig. 3-85:

Gearbox housing, filling in new oil / topping up  Unscrew caps (7, Fig. 3-87:) from expansion reservoirs (5) and fill in new gearbox oil.

The expansion tanks must be filled with oil up to abt. 1/3.

The oil level is visible from outside (light/dark area).  Screw caps (7) back in place.

Fig. 3-86:

Fig. 3-87:

3-78

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing Brake chamber, draining off oil

Gearbox venting

 Prepare a collecting recipient for used oil.

Choose the required capacity in accordance with the "Refilling quantities - Oil" table.

The gearbox is vented through the caps of the expansion reservoirs (7, Fig. 3-89:).

 Unscrew caps (7, Fig. 3-89:) from expansion reservoirs (6). Oil will escaping faster then.  Unscrew plug at the upper edge of the gearbox housing (arrow, Fig. 3-88:).

Oil escapes.  Screw plug (arrow, Fig. 3-88:) back in place.

Brake chamber, filling in new oil / topping up  Fill in new gearbox oil into expansion reservoirs (6, Fig. 3-89:).

The expansion tanks must be filled with oil up to abt. 1/3.

The oil level is visible from outside (light/dark area).

Fig. 3-89:

 Screw caps (7) back in place.

Fig. 3-88:

BA RH170B(3 725 013.00)-EN

3-79

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing TRAVEL GEARBOX The gearbox housings may be hot, too.

Read and observe: "Inspection and servicing - Safety instructions.

Shut off the electric motor.

Pre-chamber / spur wheel section, Check the oil level / Top up with oil  Check oil level at inspection glass (2, Fig. 3-91:). The oil level should reach up to the middle.

If required, screw out plug (4) and top up with oil (oil grade see: "LUBRICANTS").

Secure the machine as described in the "Securing the machine" section.

Protect the skin from contact with gearbox oil.

Skin contact with cooling liquid is a potential health hazard.

Wear protective gloves and firm working clothing.

Carry out oil change when gearoil is nearly at operating temperature. All suspended particles and contaminations will be rinsed out with the old oil.

Oil grade see”LUBRICANTS”.

Gearbox - Checking the oil level / Topping up with oil  Move the excavator into such a position that the screw plugs (1, 2 and 3, Fig. 3-90:) are in the displayed position.  Unscrew checking screw (1).

The oil level should reach up to the lower edge of the opening. Top up with oil, if required. (oil grade see: "LUBRICANTS").

Fig. 3-91:

Hydraulic motor chamber - Check the oil level / Top up with oil  Unscrew checking screw (6, Fig. 3-92:). The oil level should reach up to the lower edge of the opening. If required, screw out plug (5) and top up with oil through the opening.  Screw checking plug (6) back in place.

 Screw checking plug (1) back in place.

Fig. 3-92: Fig. 3-90:

3-80

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing Travel gearbox, Changing oil Draining off oil  Move the excavator into such a position that the screw plugs (1, 2 and 3, Fig. 3-93:) are in the displayed position.  Place a collecting recipient for used oil under the travel gearbox.

Choose the required capacity in accordance with the "Refilling quantities - Oil" table.  Unscrew drain plug (2) and drain off the oil completely.

Slackening plug (3) allows the oil to run out more readily.  Clean screw plugs (2 and 3).  Screw screw plug (2) back in place.

Pre-chamber / spur wheel section, Changing oil Draining off oil  Place a collecting recipient for used oil under the pre-chamber / spur wheel section.

Choose the required capacity in accordance with the "Refilling quantities - Oil" table.  Unscrew drain plug (3, Fig. 3-94:) and drain off the oil completely.

Slackening plug (4) allows the oil to run out more readily.  Clean screw plugs (3 and 4)  Screw screw plug (3) back in place.

Filling in oil (oil grade see: "LUBRICANTS").

Filling in oil

 Unscrew screw plugs (4).

(oil grade see: "LUBRICANTS").  Unscrew screw plug (1 and 3).

 Fill in oil through opening of plug (4) until it reaches the middle of inspection glass (2).

 Fill in oil through opening in plug (3) until it flows out of opening in plug (1).

 Screw plug (4) back in place.

 Screw plugs (1 and 3) back in place.

Fig. 3-94: Fig. 3-93:

BA RH170B(3 725 013.00)-EN

3-81

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing Hydraulic motor chamber, Changing oil Draining off oil

Breather filter, Clean / Replace  Unscrew breather filter (1, Fig. 3-95:) and clean in white spirit or parafin.

Replace according to maintenance plan.

 Place a collecting recipient for used oil under the hydraulic motor chamber.

Choose the required capacity in accordance with the "Refilling quantities - Oil" table.  Unscrew drain plug (7, Fig. 3-95:) and drain off the oil completely.

Slackening plug (5) allows the oil to run out more readily.  Clean screw plug (7).  Screw screw plug (7) back in place.

Filling in oil (oil grade see: "LUBRICANTS").

Fig. 3-96:

 Unscrew screw plug (6).  Fill in oil through opening of plug (5) until it flows out of opening of plug (6).  Screw plugs (5) and (6) back in place.

Fig. 3-95:

3-82

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing CRAWLER TRACKS Cleaning Clean tracks, track and support rollers, sprockets and idlers regularly and whenever required. Cleaning is especially important in winter to prevent  the tracks from being thrown off, 

oil from leaking out of track and support rollers, sprockets and idlers,



excessive wear,



the track from breaking.

To clean the tracks:  raise one side of the excavator with the working equipment and allow track to turn;  clean the side member supporting the track;  clean track and support rollers (1 and 2 ,Fig. 3-97:) thoroughly;  clean the sliding planes on the idler guides.

Fig. 3-97:

BA RH170B(3 725 013.00)-EN

3-83

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing Track / support rollers, greasing The track rollers and support rollers (Fig. 3-98:) have a permanent grease filling. In this case it is necessary to press in grease filling at regular intervals.

It is necessary to be sure that there is always sufficient grease in the roller bearings.

Inspect all track and support rollers visually for leaks and free movement at regular intervals.

The track rollers and support rollers (Fig. 3-98:) can be supported with grease by means of the automatic undercarriage greasing system (optional).

Track roller / support roller, fastening Inspect all track and support rollers visually for leaks and free movement at regular intervals.

Track roller fastening  Check fastening screws (4, Fig. 3-99:) regularly for tightness.  Tighten screws with a torque wrench to the prescribed tightening torque (see Technical Handbook).

Support roller fastening  Check fastening screws (3, Fig. 3-99:) regularly for tightness.  Tighten screws with a torque wrench to the prescribed tightening torque (see Technical Handbook).

Fig. 3-98:

 Unscrew plug (6, Fig. 3-98:) from breather line.

Fig. 3-99:

 Remove dust cap (1) from coupling (2).  Remove dust cap (4) from plug (5).  Connect grease hose (3) to couling (2).  Press in grease as long as used grease emerges from breather line.  Screw on plug (6) to breather line.  Disconnect the grease hose (3).  Fix dust caps (1 and 4) back in place.

3-84

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing Track tensioner Design The tracks are tensioned with the help of the hydraulic pressure created during travelling. Fig. 3-100: and Fig. 3-101: show parts of the tracks and the tensioner:

Techncal data Track tensioning pressure Pressure limiting valve Gas pressure in pressure accumulator (nitrogen filling pressure)

ca. 70 bars / 1015psi 330 bars / 4786psi 50 bars / 725psi

Function The tensioning system is under permanent pressure of ca. 70 bars which keeps both tracks permanently tensioned. Pressure losses are compensated as soon as the electric motor has been started. Retensioning is not required.

For cleaning and servicing work, the tracks can be slackened.

To do so:  Switch off the electric motor.

Fig. 3-100:

1 2 3 4 5 6 7 8 9

Crawler track Idler Drive sprocket Support roller Pressure accumulator Pressure cylinder Pressure limiting valve Track roller Mini- measuring port

 Open both pressure limiting valves (7, Fig. 3-101:) to slacken the tracks.  After the work, screw down the pressure limiting valves (7) to the limit stop.

Fig. 3-101:

The pressure-limiting valves (7) are preset to a pressure of 330 bars and sealed in this position.

The lead seal must not be removed and the pressure setting of 330 bars must not be changed.

The track tensioners are maintenance-free.

BA RH170B(3 725 013.00)-EN

3-85

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing Pressure-accumulator inspection regulations

Checking the gas charging pressure in the pressure accumulator

The following regulations are applicable only in Germany. Please observe the relevant regulations in force in your own country.

After commissioning (new installation or repair), the gas charging pressure in the pressure vessel must be checked at least once during the first week. If no pressure loss is detected, the second pressure test must be performed after ca. 3 months. If no pressure loss is detected in this test either, the testing interval can be fixed at once pressure test each year.

Extract from the German regulations The accumulator vessel must not be subjected to welding, soldering or any other mechanical work.

Work on systems containing accumulators (repairs, connection of pressure gauges or similar work) may be carried out only when the fluid pressure has been relieved.

Extract from the German acceptance regulations Hydraulic accumulators are pressure vessels and are therefore subject to the "Druckbehälterverordnung (DruckbehV)" [Pressure Vessel Regulations].

Their installation, equipment and operation are governed by the "Technische Regeln Druckbehälter (TRB)" [Technical Rules for Pressure Vessels]. The pressure vessels of hydraulic accumulators are classified by the admissible operating pressure p in bars, the capacity l in liters and the product of pressure and capacity p x l. Depending on the class to which the accumulator belongs, the following inspections are mandatory:

The above-mentioned pressure tests are required to ensure the functioning of the track tensioner.

They are no substitute for the inspections as required by the "Pressure Vessel Regulations".

Before checking the gas charging pressure (nitrogen filling pressure) in the pressure accumulator, the track must first be slackened, i.e. the hydraulic part of the tensioning system must be depressurized. Cf. under "Function".

For measuring the precharge pressure in the pressure accumulator, observe the instructions set out in the booklet "Filling and testing device for pressure accumulators" annexed to this documentation.

Tab. 3-1

Group IV p ≥ l bar p·x l ≥ 1000

3-86

Inspections prior to commissioning at the factory at the place of use Preliminary inspection by an Acceptance inspection by an expert expert Prototype and pressure test certified by the manufacturer (type approval) or the expert

Regular inspections Internal inspection: every 10 years for noncorrosive fluids; otherwise pressure testing every 5 years: every 10 years by an expert

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing SWING RING Read and observe: "Inspection and servicing - Safety instructions.

Internal gearing The internal gearing (1, Fig. 3-103:) and the pinion (2) are enclosed in a housing (3, Fig. 3-104:). The housing forms a grease-filled trough in which the pinion of the swing mechanism moves.

Switch off the electric motor.

Wear protective gloves and firm protective clothing.

Swing ring - Instructions The grease filling must be replaced:  when repairs have been carried out on the slewing ring, the slewing ring seals or the slewing ring housing.

Remove old grease completely before filling in new grease.

If greater losses are detected, locate cause immediately to prevent damage to the slewing ring.

Greases and greasy cleaning rags must not be allowed to pollute the environment. Discard grease and greasy cleaning rags separately from other waste without polluting the environment.

Bearing races The central lubricating system supplies grease continuously to the two roller bearing races and the internal gearing .

Fig. 3-103:

The grease is pumped to the greasing port of the grease trough by the distributor (Fig. 3-102:). The amount of grease used up during operation is replenished by the central lubricating system.

The housings have a check opening which is closed with a cover (2, Fig. 3-104:). For checking, the cover must be removed.

The grease is pumped to the greasing points of the bearing races by a distributor (Fig. 3-102:).

Fig. 3-104:

Fig. 3-102:

BA RH170B(3 725 013.00)-EN

3-87

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing Swing ring - Checking the grease filling Read and observe: "Inspection and servicing - Safety instructions.

Swing ring - Filling in grease Prior to initial commissioning, the grease trough of the internal gearing must be filled with grease.

Add grease when  the housing has been replaced,

Switch off the electric motor.

Wear protective gloves and firm protective clothing.

At regular intervals  check internal gearing and teeth of swing mechanism pinion for condition,



old grease has been removed in the course of other work.

Always fill in fresh grease by hand.

Risk of accidents. Never slew the superstructure when refilling grease.

 check that the grease filling is sufficient.

The housing must always contain enough grease for the gearing - measured from its lower edge - to run in at least 20 mm (0.78”) of grease over its whole circumference (Fig. 3-105:).

In the event of greater grease losses, eliminate cause immediately and add grease to prevent the internal gearing and the pinion from being damaged by continued swing movements.

Swing ring - Checking the screws for tightness The fastening screws of the swing ring in the superstructure and the undercarriage are tightened with their respective check torque (see Technical Handbook).

When these values are reached, the fastening screws are perfectly tight.

Loosen slack screws before tightening them with a torque wrench to the prescribed torque (see Technical Handbook).

Fig. 3-105:

3-88

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing CENTRAL LUBRICATING Design and function The excavator is equipped with an automatic central lubricating system which provides grease regularly to all greasing points except those mentioned in the "Lubricating chart - Grease".

The central lubricating system is activated when the electrical system is switched on with the keyswitch and the electric motor is running. All greasing points connected to the system are greased at regular intervals.

The central lubricating system is controlled electrohydraulically by the programmable SPC contoller.

The SPC is located in a switch box underneath the cab.

Fig. 3-107:

If a fault occurs, BCS gives a warning on the screen (Fig. 3-107:).

Actuate the "Reset" button (73, Fig. 3-106:) for 5 seconds to eleminate the fault. Is this is not possible, call in servicing personal.

For further information on the function and setting refer to the TECHNICAL HANDBOOK – PLC (Programmable Logic Controller).

Fig. 3-106:

BA RH170B(3 725 013.00)-EN

3-89

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing Function The grease is pumped by the pump (1, Fig. 3-108:) via greasing lines from the grease container to the main distributors on the superstructure and on the undercarriage.

The control elements of the lubricating system are installed on the panels (3).

Fig. 3-110:

As soon as the grease container is empty, the BCS (Fig. 3-111:) gives a warning signal. In the event of a fault, the "dumping" function is switched off automatically after 15 min.

Fig. 3-108:

Work can be continued when the grease container is filled with grease.

For machines with automatic greasing of the track rollers, optional: The grease is pumped by the pumps (1 and 3, Fig. 3-109:) via greasing lines from the grease container to the main distributors on the superstructure and on the undercarriage.

The control elements of the lubricating system are installed on the panels (3 and 21, Fig. 3-110:).

Fig. 3-111:

Fig. 3-109:

3-90

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing Filling up the grease container

Breather filter

Fill up the grease container through the service station (Fig. 3-112:).

Check/change the breather filter at regular intervals.

The use of the hose is described in the chapter "Flexible hose for the change of oil "

 Unscrew wing nut (10, Fig. 3-113:).

 Switch on the indicator system with toggle switch (23, Fig. 3-112:). Monitoring lamp (22) comes on.  Unscrew the cap of the express coupling (11).

 Withdraw cover (7, Fig. 3-114:) and filter element (8).  Check filter element. Replace if necessary.  Re-install breather filter.

 Connect the filling hose of the service vehicle.  When the grease container is full, the indicator lamp (34) lights up.  Switch off the indicator system with toggle switch (23). Monitoring lamp (22) is off.  Remove the flexible hose.

The express coupling closes automatically.  Refit the protective cap.

Fig. 3-113:

Fig. 3-112:

Fig. 3-114:

BA RH170B(3 725 013.00)-EN

3-91

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing Checking the greasing pressure Check every week, whether the oil pressure indicated by pressure gauge (4, Fig. 3-115:) is 60 bars / 870psi (the pressure is dependind on temperature and viscosity of the oil and may vary).

This oil pressure is reduced so that the pressure indicated by pressure gauge (2) is 47 – 50 bars (681-725psi).

The necessary greasing pressure of 320 bar / 4641psi for the superstructure is generated by means of a pressure translator.

The greasing pressure is indicated by pressure gauge (9).

In the event of deviating pressure values, switch off the electric motor and check the central greasing system.

Higher oil pressure may cause bursting of a greasing line.

Lower oil pressure means that not all of the greasing points are supplied with grease.

Always refill the grease container in time to avoid air from penetrating into the greasing system. Air in the greasing may cause malfunctions.

Fig. 3-115:

3-92

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing Checking the greasing pressure (for machines with automatic greasing of the track rollers, optional) Check every week, whether the oil pressure indicated by pressure gauge (4, Fig. 3-116:) is 60 bars / 870psi (the pressure is depending on temperature and viscosity of the oil and may vary).

The necessary greasing pressure of 320 bar / 4641psi for the superstructure and 180 bar / 2610psi for the lundercarriage is generated by means of a pressure translator.

The greasing pressure for the superstructure is indicated by pressure gauge (9, Fig. 3-116:) and for the undercarriage by pressure gauge (22).

In the event of deviating pressure values, switch off the electric motor and check the central greasing system.

Higher oil pressure may cause bursting of a greasing line.

Lower oil pressure means that not all of the greasing points are supplied with grease.

Always refill the grease container in time to avoid air from penetrating into the greasing system. Air in the greasing may cause malfunctions.

Fig. 3-116:

This oil pressure is reduced so that the pressure indicated by pressure gauge (2, Fig. 3-117:) is 35 – 40 bars (507-580psi) and by pressure gauge (4) is 49 – 51 bar (710-739psi).

Fig. 3-117:

BA RH170B(3 725 013.00)-EN

3-93

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing Unblocking a grease line.

Unblocking a grease line.

Put the excavator back into operation only after the lubricating system works properly and after having actuated the unloaded working equipment for abt.

5 minutes. This is necessary in order to supply sufficient amounts of grease to the cylinder bearings.

(for machnes with automatic greasing of the track rollers, optional)

Check the grease sieve regularly for contamination and clean, if required. The grease sieve must also be cleaned after an obstruction in one of the grease lines.

Cleaning  Loosen nut (6, Fig. 3-118:).  Withdraw sieve and clean with white spirit or paraffin oil.  Re-insert sieve and fasten with nut (6).

Put the excavator back into operation only after the lubricating system works properly and after having actuated the unloaded working equipment for abt.

5 minutes. This is necessary in order to supply sufficient amounts of grease to the cylinder bearings.

Check the grease sieve regularly for contamination and clean, if required. The grease sieve must also be cleaned after an obstruction in one of the grease lines.

Cleaning  Loosen nut (6, Fig. 3-119:).  Withdraw sieve and clean with white spirit or paraffin oil.  Re-insert sieve and fasten with nut (6).

Fig. 3-118: Fig. 3-119:

3-94

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing Oilfilter (hydraulic circuit grease pump) ) Read and observe the "Inspection and servicing - Safety instructions" chapter.

Replacing the filter element Change filter element regulary and when the BCS indicates a contamination.

Switch off the electric motor.

Risk of scalding caused by hot hydraulic oil.

The filter housings may also be hot.

Avoid skin contact.

Skin contact with hydraulic oil may cause skin injury.

Wear protective gloves and firm working clothing.

For filtering of the hydraulic oil, high pressure filter (11, Fig. 3-120:).is installed in the pumping line.

Fig. 3-121:

 Unscrew filter housing (5, Fig. 3-121:).  Withdraw filter element (6) from filter housing (5).  Clean filter housing (5) and the sealing face at the filter head (9) with white spirit or paraffin oil.  Check seals (10 and 14) and replace, if required.  Insert new filter element into filter housing (5) and refit to the filter head with new, lightly oiled sealing ring (8).

Fig. 3-120:

BA RH170B(3 725 013.00)-EN

 Check for leaks after putting the filter into operation.

3-95

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing Grease filter (Filling the grease container) Read and observe the "Inspection and servicing –Safety instructions" chapter.

Switch off the electric motor.

Grease filter (13, Fig. 3-122:) is installed in the greasing line to the grease container.

Checking the filter element  Unscrew filter housing (32, Fig. 3-123:).  Withdraw filter element (33) from housing (32).  Remove the grease.  Clean filter housing and contact faces at the filter head with white spirit or paraffin oil.  Insert filter element into housing (32) and attach to the filter head with a new, slightly oiled sealing ring (36).  Check the high-pressure filter for leaks after the system has been put into operation.

Fig. 3-122:

Fig. 3-123:

Replacing the filter element  Remove filter element as described under "Checking the filter element".  Insert new filter element and reassemble.  Check high-pressure filter for leaks after the system has been put into operation.

3-96

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing Grease filter (Grease lines) Read and observe the "Inspection and servicing –Safety instructions" chapter.

Switch off the electric motor.

Grease filter (12, Fig. 3-124:) is installed in the greasing line to the grease container.

Checking the filter element  Unscrew filter housing (42, Fig. 3-125:).  Withdraw filter element (43) from housing (42).  Remove the grease.  Clean filter housing and contact faces at the filter head with white spirit or paraffin oil.  Insert filter element into housing (42) and attach to the filter head with a new, slightly oiled sealing ring (46).  Check the high-pressure filter for leaks after the system has been put into operation.

Fig. 3-124:

Fig. 3-125:

Replacing the filter element  Remove filter element as described under "Checking the filter element".  Insert new filter element and reassemble.  Check high-pressure filter for leaks after the system has been put into operation.

BA RH170B(3 725 013.00)-EN

3-97

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing OTHER MAINTENANCE Heating and air conditioning Change the filter mats in the air suction regulary.

Air intake filters Empty dust trap of the intake filter (1, Fig. 3-127:) and clean filter element respectively replace.

For servicing works cf. Section „Switchgear cabinet“ in the chapter „Electrical system“.

The filter mats are located in the air conditioner housing (Fig. 3-126:) below the cab roof.  Open housing of air conditioner.  Clean filter mats or replace if necessary.  Close housing.

Fig. 3-127:

Fig. 3-126:

3-98

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing Equipment, check for cracks

Hydraulic oil cooler, cleaning

Check the welded joins of the working equipment regulary.

Serious injuries may happen.

The fans motors can start rotating automatically depending on the temperature of the hydraulic fluid.

Inspections must be carried out acc. to the "Structural Inspection Reports" every 500 OH and every 5000 OH.

Therefore: Let the machine and the whole hydraulic system cool down to ambiant temperature before working at the coolers.

"Structural Inspection Report" forms for those inspections can be downloaded from the Bucyrus HEX website, section "Support, Warranty".

The inside located joins are accessible through the man-holes in stick (arrow, Fig. 3-128:) and boom (arrow, Fig. 3-129:).

Check the radiators regularly.  Shut off the electric motor.  Remove any accumulated dirt.  Clean the fan blades (2, Fig. 3-130:).  Clean the radiators with a jet of water or compressed-air from the outside.  Dry up coolers.  Check hydraulic motors (1) for free movement.  Attach all guards back in place.

Do not clean radiators with a wire brush or similar hard objects.

In case of firmly adhering dirt, remove radiator and clean.

Fig. 3-128:

Fig. 3-130: Fig. 3-129:

BA RH170B(3 725 013.00)-EN

3-99

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing HYDRAULIC LADDER To allow the hydraulic ladder (Fig. 3-131: and Fig. 3-132:) to be lowered in an emergency, the ladder mechanism is equipped with a pressure accumulator (1, Fig. 3-133:).

The pressure accumulator (1) is located in the superstructure and is accessible from the ground.

Check nitrogen pressure inside the pressure accumulator regularly (see Technical Handbook).

Fig. 3-133:

Fig. 3-131:

Fig. 3-132:

3-100

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing Pressure-accumulator inspection regulations

Checking the gas charging pressure in the pressure accumulator

The following regulations are applicable only in Germany. Please observe the relevant regulations in force in your own country.

After commissioning (new installation or repair), the gas charging pressure in the pressure vessel must be checked at least once during the first week. If no pressure loss is detected, the second pressure test must be performed after ca. 3 months. If no pressure loss is detected in this test either, the testing interval can be fixed at once pressure test each year.

Extract from the German regulations The accumulator vessel must not be subjected to welding, soldering or any other mechanical work.

Work on systems containing accumulators (repairs, connection of pressure gauges or similar work) may be carried out only when the fluid pressure has been relieved.

Extract from the German acceptance regulations Hydraulic accumulators are pressure vessels and are therefore subject to the "Druckbehälterverordnung (DruckbehV)" [Pressure Vessel Regulations].

Their installation, equipment and operation are governed by the "Technische Regeln Druckbehälter (TRB)" [Technical Rules for Pressure Vessels]. The pressure vessels of hydraulic accumulators are classified by the admissible operating pressure p in bars, the capacity l in liters and the product of pressure and capacity p x l. Depending on the class to which the accumulator belongs, the following inspections are mandatory: Group III p ≥ l bar and p·x l ≥ 200 bars p·x l ≤ 1000 bars

Inspections prior to commissioning at the factory at the place of use Preliminary inspection by an Acceptance inspection by an expert expert Prototype and pressure test certified by the manufacturer (type approval) or the expert

BA RH170B(3 725 013.00)-EN

Regular inspections Inspection schedule to be drawn up by end user, based on experience with type of operation and operating fluids.

3-101

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing ON-BOARD CRANE (OPTIONAL) On-board crane, monitoring, warning and control elements

On-board crane, checking Extract from the inspection and testing regulations The on-board crane is approved in accordance with the Accident Prevention Regulations for Cranes (BGV D6, applicable only in Germany).

(Fig. 3-134:)

The on-board crane must be inspected regularly in accordance with the regulations in force in the country of use.

The inspections must be requested by the user of the crane. The expert or specialist entrusted with the inspection can be appointed at the user's discretion.

The user must ensure, however, that the appointed person meets the requirements.

Fig. 3-134:

1 2 3 4 5 6 7

Monitoring lamp Warning lamp Warning lamp Monitoring lamp Key-switch Button Monitoring lamp

8 9 10 11 12

Button Monitoring lamp Warning lamp Button Button

21 Control lever 22 Control lever 23 Control lever 24 Control lever

3-102

alternator engine oil pressure engine temperature air filter electrical system ON/OFF engine start preheating system (option) speed variation crane in operation malfunction EMERGENCY STOP emergency lowering of winch extending and retracting of boom extension folding the boom swing the boom winch ON/OFF

The user is obliged to make available all documents required for the inspection and to ensure the smooth running of the inspection. He is furthermore obliged to provide, if required, crane operators and auxiliary personnel and the required test loads.

The result of the inspection is to be documented in an inspection record signed by the inspector.

The inspection record serves as proof on the part of the user that the inspections have been carried out. The inspection record must contain all data required for crane identification and for the performance of further regular inspections.

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing On-board crane, drive unit The drive unit comprises:

Hydraulic system



crane engine,

See crane operating instructions.



hydraulic system.

Crane engine See operating instructions for the crane engine.  Fill up fuel tank through filler (5, Fig. 3-135:) after each deployment.

 Prior to each deployment, check the hydraulic oil level at the inspection glass (12, Fig. 3-135:); top up if necessary.  Check contamination of hydraulic oil filter regularly at contamination indicator (arrow, Fig. 3-135:).

 Prior to each deployment check the engine oil level with the dipstick; top up if necessary.

 Regularly, but at least once a year replace the hydraulic oil filter (14) and the breather filter (13).

 Regularly, at least once a year - change engine oil - replace engine oil filter - check / replace air filter - replace fuel filter

On-board crane, servicing

 Check batteries (7) and cable connections at regular intervals.

Air-intake system Never start up the engine when the air filter is removed.

Servicing  Lubricate all bearings regularly and as required, and spray swing ring with a graphite spray (Fig. 3-136:) 4 lube points 1 - bearing 2 - joint (column/boom) 2 lube points 3 - cylinder bearing 5 lube points 4 - swing ring

Fig. 3-135:

Fig. 3-136:

BA RH170B(3 725 013.00)-EN

3-103

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing On-Board crane, checking tightness of fastening bolts

On-Board crane, – blocking the boom in position of rest

The hydraulic driven on-board crane (Optional) is fixed on the uppercarriage of the machine by means of 16 fastening bolts. The upper and lower fastening bolts (Fig. 3-137:) are important and safety relevant components, they carry all loads and forces of the crane.

Movements and accelerations produced by working operations of the machine can cause damage to the slewing drive of the on-board crane, if the crane is not blocked.

The hydraulic on-board crane must therefore be blocked in its position of rest.

Check tightness of all fastening bolts: 

in regular intervals according to the maintenance plans and



before every start of the on-board crane.

Check tightness of the fastening bolts by means of a torque wrench. The tightening torque for fastening bolts M20, quality 10.9, lightly oiled is: 557 Nm.

Risk of serious injuries due to movements of the crane.

Put the crane into operation only after all persons have left the danger area.

To block the boom: •

Retract the boom completely.

•

Slew the boom in the direction of the blocking device (Fig. 3-138:) and lower it.

•

Withdraw the cotter pin at the tip of the boom.

•

Extend the boom carefully until the tip engages the blocking device (arrow, Fig. 3-138:).

•

Reinsert and lock the the cotter pin.

Fig. 3-137:

Fig. 3-138:

3-104

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing PUTTING THE EXCAVATOR OUT OF OPERATION AND RECOMMISSIONING Putting the excavator out of operation

Battery storage

 Park the excavator on firm and level ground.

 Check the acid density and the electrolyte level of the battery every two weeks.

 Set the working equipment down on the ground, retracting the piston rods of the hydraulic cylinders as far as possible.  Set all control element to "0".  Clean the machine.

During prolonged machine downtimes, remove the batteries and store in a dry room at an ambient temperature of ca. 20°C (68°F). Observe the following points with regard to maintenance:  Clean the batteries.

 Recharge the batteries at the latest, when the acid density has dropped to 1.23 kg/dm³.  Keep the batteries clean and dry on the outside.

 Carry out a visual inspection of the excavator.  Remove coarse dirt, snow and ice from the fins and fan wheel of the hydraulic oil cooler.  Protect all bright metal parts (e.g. piston rods) from rust and dirt.

Recommissioning  Remove the covers.  Degrease / clean all protected components.

 Remove the batteries; cf. "Battery storage".

 Check track tension (visual inspection)

 Secure the machine against unauthorized starting by: withdrawing the key from the key-switch, setting the battery main switch to OFF, setting the main circuit breaker to OFF, locking the cab door, securing all lockable hatches.

 Check grease filling in grease container.

 Cover up all openings.

 Check battery acid density and level.

 Oil level

- slewing gearboxes, - pump transfer gearboxes, - travel gearboxes.

 Check oil level in hydraulic oil reservoir.

 Install batteries and reconnect.  Set battery main switch to ON.  Set the main circuit breaker to ON.  Function checks:

- superstructure holding brake, - track brake, - lighting system, - signalling equipment.

 Vent the hydraulic system.

BA RH170B(3 725 013.00)-EN

3-105

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing

3-106

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing NOTES .............................................................................................................................................................................. .............................................................................................................................................................................. .............................................................................................................................................................................. .............................................................................................................................................................................. .............................................................................................................................................................................. .............................................................................................................................................................................. .............................................................................................................................................................................. .............................................................................................................................................................................. .............................................................................................................................................................................. .............................................................................................................................................................................. .............................................................................................................................................................................. .............................................................................................................................................................................. .............................................................................................................................................................................. .............................................................................................................................................................................. .............................................................................................................................................................................. .............................................................................................................................................................................. .............................................................................................................................................................................. .............................................................................................................................................................................. .............................................................................................................................................................................. .............................................................................................................................................................................. .............................................................................................................................................................................. .............................................................................................................................................................................. .............................................................................................................................................................................. .............................................................................................................................................................................. .............................................................................................................................................................................. .............................................................................................................................................................................. ..............................................................................................................................................................................

BA RH170B(3 725 013.00)-EN

3-107

OPERATING INSTRUCTIONS RH170B Electric Inspection and servicing

3-108

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Repair work 4 REPAIR WORK Operating instructions

Target group

Part 1 INTRODUCTION FUNDAMENTAL SAFETY INSTRUCTIONS

Operating personnel + Inspection and servicing personnel + Repair personnel

Part 2 OPERATION

Operating personnel The operating personnel must have knowhow relevant to the operation and the application of this or comparable machines.

Part 3 INSPECTION AND SERVICING Part 4 REPAIR WORK

Inspection and servicing personnel The inspection and servicing personnel must have know-how relevant to the inspection and servicing of this or comparable machines.

Repair personnel The repair personnel must have know-how and experience relevant to the repair of this or comparable machines.

Part 5 ANNEX

Part 6 INDEX

BA RH170B(3 725 013.00)-EN

Operating personnel + Inspection and servicing personnel + Repair personnel Operating personnel + Inspection and servicing personnel + Repair personnel

4-1

OPERATING INSTRUCTIONS RH170B Electric Repair work

4-2

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Repair work SAFETY INSTRUCTIONS FOR EXCAVATORS WITH ELECTRIC MOTOR

Connect the earthing kit (8) to the earthing points (2, 3 and 4) only by means of extension (5).

Repair work on electrical systems may only be performed by qualified electricians or by workshops employing such personnel.

The earthing points may still carry residual voltages.

A qualified electrician for the purpose of this regulation is a person who has the corresponding technical training, know-how and experience as well as knowledge of the pertinent prescriptions and who is therefore in a position to judge the work entrusted to him and the potential dangers in connection therewith.

Before carrying out any repair work on the electrical system, the following precautions must be taken:

In the transformer station  Cut out the supply voltage.  Secure against switching on; apply a warning sign.

Fig. 4-1:

 Check that the electrical system is off circuit.  Connect to earth and short-circuit.  Protect adjacent and live parts against accidental contact.

On the excavator  Cut out the switch-disconnector (see the " Switching off the circuit breaker " chapter in part 2 of the present operating instructions)  Secure the circuit breaker against switching on, e.g. seal in the actuating lever in a cabinet.  Apply a warning sign.  Remove the cover (1, Fig. 4-1:).

Fig. 4-2:

 Check that the electrical system is off circuit and dead. 

Connect to earth and short-circuit: (connect the earthing and short-circuiting line (8, Fig. 4-2:) in the following order to points (1 – 4): first to the fixed point (1), then one after another to the earthing points (2, 3 and 4).

 Slide partition (6, Fig. 4-3:) into guide (7).

Fig. 4-3:

BA RH170B(3 725 013.00)-EN

4-3

OPERATING INSTRUCTIONS RH170B Electric Repair work After repair, the following works must be performed:

On the hydraulic excavator  Disconnect the earthing and short-circuiting line (8, Fig. 4-4:): first from the earthing points (2, 3 and 4) by means of extension (5), then from the fixed point (1).  Withdraw the partition (6, Fig. 4-5:) .  Refit the cover (1, Fig. 4-6:).

Fig. 4-6:

In the transformer station  Disconnect the earthing and short-circuiting line.  Unlock the safety device preventing switch-on; remove the warning sign.  Remove the partitions.

Fig. 4-4:

 Switch on the supply voltage.

On the hydraulic excavator  Remove the warning sign.  Cut out the switch-disconnector (see the " Switching off the circuit breaker " chapter in part 2 of the present operating instructions).

Fig. 4-5:

4-4

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Repair work REPAIR WORK - SAFETY INSTRUCTIONS Operating instructions Never carry out repair work without having read and understood the operating instructions.

Pay special attention to: "Fundamental Safety Instructions", "Inspection and servicing - safety instructions" and all warnings and safety instructions attached to the machine.

The descriptions of job sequences provide only experienced personnel with the necessary instructions.

The operating manual must be kept with the machine at all times.

Prestressed units Never open defective prestressed units but replace them as an entirety.

In exceptional cases, open only when the system and the operating sequence are precisely known and any special tools required are available.

The operating manual contains no information on this point.

Dismantling components Never do dismantling while the machine is at operating temperature.

Oils, greases, or coolants may have a high temperature and result in burning or scalding.

Leave time for the machine to cool down.

Repair personnel Repair personnel must have know-how and experience relevant to repairing this or comparable machines.

In the absence of such know-how, meticulous training must be given by experienced repair personnel, e.g. from Bucyrus HEX.

Working in greater heights Always wear safety harnesses when working at greater heights.

Wear an approved safety harness; it must be equipped with fall arresters and safety cables.

BA RH170B(3 725 013.00)-EN

Before starting work, depressurize piping and hoses, cylinders, radiator, hydraulic tank and other systems or units.

Replace defective components in good time to prevent major damage.

Clean the defective component carefully before dismantling it.

Mark the dismantled parts in the correct sequence to faciliate re-assembly.

When dismantling the component, close off exposed hose and piping connections, exposed drill holes and housings carefully to prevent any dirt from penetrating.

4-5

OPERATING INSTRUCTIONS RH170B Electric Repair work Never remove lead seals Never change rated pressure of pressure relief valves without the explicit authorization of Bucyrus HEX. Never remove lead seals from pressure relief valves and accumulators.

After the repair work To prevent corrosion, coat all bright metal machine parts with a grease film.

On completing the work, re-assemble all protective devices, covers and noise- and vibrationinsulation material.

Never start up the electric motor while work is being done on the machine.

Check the repaired components and all machine functions in a trial run.

Never release the machine for recommissioning until it is fully functioning.

4-6

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Repair work FIRE AND EXPLOSION HAZARD Safety Instructions Prior to commencing work, inform on the national and corporate rules for prevention of accidents. Pay particular attention to hazards caused by combustible and easily flammable substances. on the safe handling of the fire extinguishers to be used.

Flying sparks (caused by welding, flame cutting, grinding, electrical short-circuit) may cause fire on the ground that can spread to the excavator.

Place suitable fire guardings (fire barriers) if open fire or flying sparks cannot be avoided during repair work. Apply special protection to cables, cable ducts as well as to hose and pipe lines.

If necessary, also cover the ground with fireprotective blankets.

Ensure sufficient ventilation.

Clean the excavator before starting a job.

Avoid smoking and open fire on, next to and below the excavator.

Combustible and easily flammable substances or liquids increase the fire and explosion hazard.

Do not store or handle any flammable substances during operation.

Clean the excavator thoroughly, if possible, with a steam jet (rubber parts and electric components with compressed air - refer to information label), when, for example, oil, grease, fuel or cleaner was spilled.

Such substances may spontaneously ignite if they get into the vicinity of hot units.

Even battery gases can ignite in open flames or fire.

Avoid parking the excavator in places where  combustible substances such as coal dust or tar are present. 

Do not keep any fire extinguishers that are not suitable or have not been tested.

Do not extinguish flammable liquids with water.

Use:  dry-powder, 

carbon-dioxide or



foam extinguishing compounds.

When getting into contact with burning substances, the fire-fighting water would abruptly evaporate and distribute the substance such as oil over a wide area. Water causes short-circuits in the electrical system thus possibly entailing new hazards.

Call the fire brigade.

Have all your welding, flame cutting and grinding work approved.

open or smouldering fire may occur.

Remove the excavator from such an area where combustible or easily flammable liquids have spilled from the excavator onto the ground.

BA RH170B(3 725 013.00)-EN

4-7

OPERATING INSTRUCTIONS RH170B Electric Repair work HYDRAULIC SYSTEM Repair instructions Always depressurize the hydraulic system before disconnecting any hydraulic hoses or pipes.

Read and observe also the chapters "Inspection and servicing - Safety instructions" and "Repair - Safety instructions".

Replace damaged and leaking hydraulic hoses and pipes as soon as possible by new ones.

Use original spare parts from Bucyrus HEX. They are adapted to the respective function.

Do not re-use old hoses.

Never repair damaged hoses.

Discard escaped oil and oily wastes without polluting the environment. These substances must not be allowed to penetrate into the soil.

4-8

Hydraulic hoses – Instructions Even hoses that have been properly stored or used are subject to natural ageing. Their useful life is therefore limited.

Hydraulic hoses must replaced after a service life of six years (including a storage time of 2 years).

Check the date of manufacture on the hose or on the hose fitting regularly.

The recommended interval after which hydraulic hoses - and especially those used in harsh conditions - must be replaced depends on the number of operating hours and on pressure loading.

The use of hoses close to their recommended load limit shortens the replacement interval (e.g. high temperatures, frequent working cycles, extremely high pulse frequencies as well as multi-shift operation and round-the-clock work).

Hydraulic hoses must be replaced, if one of the following defects is detected during a visual inspection:  Damage to the outer fibre reinforcement layer reaching down to the inner layer (cuts, chafe marks, cracks). 

Embrittlement of the outer fibre reinforcement layer (cracks in the hose material).



Changes in the ususal shape of the hose under pressure or in pressureless condition in bends or curves such as detachment of fibre layers, formation of bubbles or bulges.



Leaks.



Non-observance of fitting requirements.



Damage to or deformation of hose fittings that may result in a reduction of the strength of the screwed union.



Detachment of the hose from the fitting.



Corrosion in fittings reducing the strength of the function of the fitting.

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Repair work PRESSURE ACCUMULATORS SAFETY INSTRUCTIONS The hydraulic system is equipped with pressure accumulators containing nitrogen under high initial pressure.

Even when the hydraulic pressure in the system is reduced, the nitrogen in the accumulator will remain under pressure.

The accumulators are completely safe in operation. If incorrectly handled, however, there is a risk of explosion.

So:  Never handle accumulators never weld or solder.

mechanically,

 Testing and servicing work must be carried out by experts only.  Prior to any testing and servicing work, depressurize the hydraulic part of the system.  To dismantle the accumulator, always wear goggles and working gloves.  Fill accumulator with nitrogen only, never with compressed air or oxygen.  Report any defects or damage to the machine owner without delay.  Prior to recommissioning, an inspection by a specialist or expert is essential if the accumulator was damaged or if the admissible operating temperature or operating pressure was exceeded.

Never remove or paint over warning and information plates, rating plates or type identification markings. Replace illegible or damaged plates immediately

BA RH170B(3 725 013.00)-EN

4-9

OPERATING INSTRUCTIONS RH170B Electric Repair work WELDING OPERATIONS SAFETY INSTRUCTIONS Welding operations only by trained personnel Never perform welding operations unless you are qualified to do so.

Observe the accident prevention regulations.

Wear protective clothing: 

protective suit,



protective gloves,



face protection.

Pressurized vessels and pressure accumulators Never weld at pressure accumulators.

Any work on receptacles that contain or have contained substances 

which are combustible or which encourage combustion,



which are susceptible to explosion,



or which may develop health-hazardous gases, vapours, mist or dust

during welding operations must be carried out only under expert supervision and only by experienced persons authorized to do such work.

Pressure vessels containing cold-starting fluid (ether) may be installed in or near the engine compartment.

Ether is toxic and highly flammable; the vessels are under pressure. These pressure vessels can explode if exposed to high temperatures (above 49°C / 120°F) or in the event of damage.

Protect the vessels against damage and high temperatures.

Do not perform welding work in the vicinity of these pressure vessels before they have been covered up safely against accidental contact or flying sparks. Have the pressure vessels removed from the machine, if safe protection cannot be ensured.

4-10

Swing joints and hinges The welding current must not flow via the ball resp. the roller bearing slewing ring, via pin couplings, articulated joints or hydraulic cylinders.

An electric current flowing over an air gap (in an articulated joint, for instance) generates sparks that damage metallic surfaces.

Attach the welding-current pincers as close as possible to the welding zone.

Notes on the electric system Switch off the electrical system (“Ignition off”).

Switch off the battery main switch (alternatively disconnect the cables from the batteries).

Place welding cables as far as possible away from electric lines.

If one of these procedures could not be performed, all electrical terminals and plugs must be disconnected from every electronical units before starting welding.

Protect the disconnected terminals and plugs from short-circuiting and soiling by covering them with foil or adhesive tape.

On completion of the welding operation, restore all electrical connections.

Never touch housings of the electronical componets and units with a welding electrode.

Additional information Detailed information on the correct execution of welding operations is given in the technical manual "Welding for maintenance and repair".

Should you have any problems or queries, apply to the Bucyrus HEX after-sales service department.

If parts of the machine have to be dimantled, read and take note of the following sections: Assembling attachments - safety instructions", "Inspection and servicing - safety instructions", "Repair - safety instructions".

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Repair work NOTES .............................................................................................................................................................................. .............................................................................................................................................................................. .............................................................................................................................................................................. .............................................................................................................................................................................. .............................................................................................................................................................................. .............................................................................................................................................................................. .............................................................................................................................................................................. .............................................................................................................................................................................. .............................................................................................................................................................................. .............................................................................................................................................................................. .............................................................................................................................................................................. .............................................................................................................................................................................. .............................................................................................................................................................................. .............................................................................................................................................................................. .............................................................................................................................................................................. .............................................................................................................................................................................. .............................................................................................................................................................................. .............................................................................................................................................................................. .............................................................................................................................................................................. .............................................................................................................................................................................. .............................................................................................................................................................................. .............................................................................................................................................................................. .............................................................................................................................................................................. .............................................................................................................................................................................. .............................................................................................................................................................................. ..............................................................................................................................................................................

BA RH170B(3 725 013.00)-EN

4-11

OPERATING INSTRUCTIONS RH170B Electric Repair work

4-12

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Annex 5 ANNEX Operating instructions

Part 1 INTRODUCTION FUNDAMENTAL SAFETY INSTRUCTIONS Part 2 OPERATION

Target group

Operating personnel + Inspection and servicing personnel + Repair personnel Operating personnel The operating personnel must have knowhow relevant to the operation and the application of this or comparable machines.

Part 3 INSPECTION AND SERVICING Part 4 REPAIR WORK

Inspection and servicing personnel The inspection and servicing personnel must have know-how relevant to the inspection and servicing of this or comparable machines.

Repair personnel The repair personnel must have know-how and experience relevant to the repair of this or comparable machines.

Part 5 ANNEX

Operating personnel + Inspection and servicing personnel + Repair personnel

Part 6 INDEX

Operating personnel + Inspection and servicing personnel + Repair personnel

BA RH170B(3 725 013.00)-EN

5-1

OPERATING INSTRUCTIONS RH170B Electric Annex

5-2

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Annex TROUBLESHOOTING Instructions on troubleshooting

Layout of the fault table

Faults are often due to the machine not being correctly operated or serviced.

Fault

For this reason, it is vital to read through the relevant section of the operating instructions once again before rectifying any faults.

The fault is described here as the outcome of an observation or a previous activity.

Therefore make careful observations.

If you are unable to detect the cause of the fault or to rectify it, apply to the Bucyrus HEX after-sales service.

Study the problem carefully. First think, then act.

Describe the fault and all accompanying circumstances as precisely as possible when calling on the Bucyrus HEX after-sales service. Exact data allow for fast troubleshooting.



What repair and servicing work was carried out previously?



Has this defect already occurred?

Never do any jobs for which you are not qualified.



The fault table lists all faults which have been reported to date and outlines their possible causes and rectifying measures. In exceptional cases, a described fault may also have a different cause.

Is it one or several simultaneously occurring faults?

Possible causes

Ask yourself the following questions:  Which warning signals preceded the fault?

The possible causes of the observed fault are outlined in this group. They are arranged in order of probability, i.e. the possible cause occurring in most cases heads the list.

Measures This describes the troubleshooting procedure.

Section This specifies where information on troubleshooting is given in the operating instructions. If there is no entry, the Bucyrus HEX after-sales service should be consulted

BA RH170B(3 725 013.00)-EN

5-3

OPERATING INSTRUCTIONS RH170B Electric Annex FAULT TABLES Working hydraulics – Fault table Fault

Remedial action

Working and slewing functions not operational No boom function No bucket function No backhoe function No stick function Working movements too slow Power loss in working hydraulics Uncontrolled working movements Cause Electronic excavator control not activated/defective

•

Check Adjust Replace Top up Reduce Clean

P E W A S R

1) Contact the Bucyrus HEX Service Abschnitt Working P

•••••

•

Malfunction of pressure-relief valve

1)

•

•

Servo system pump defective

1)

••••• • •

•

5-4

• Malfunction of primary / sencondary pressure-relief valves ECO-power switch in 80%-position Hydraulic oil temperatur too high (warning lamp lit, PMS fault indicator Hydraulic oil lamp lit) oil cooler contaminated cooler cleaning • Malfunction of solenoid valves • Malfunction of control spool

1) P P/R

1) 1)

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Annex Track drive – Fault table Fault

Remedial action

No forward travel and no reversing travel Maximum travel speed cannot be reached Insufficient traction power

•

•

•

• •

• • • • •

• • •

Cause Malfunction of pressure-relief valves

Check Adjust Replace Top up Reduce Clean 1) Contact the Bucyrus HEX Service Chapter ref.

Servo system pump defective Malfunction of travel valve (pedal) Malfunction of control spool ECO-power switch in 80%-position Travelling Hydraulic oil temperatur too high (warning lamp lit, PMS fault indi- Hydraulic oil cator lamp lit) oil cooler contaminated cooler cleaning

BA RH170B(3 725 013.00)-EN

P E W A S R

1) 1) 1) 1) P P/R

5-5

OPERATING INSTRUCTIONS RH170B Electric Annex Slewing mechnism – Fault table Fault

Remedial action

No slewing possible No righthand or lefthand slewing Slewing performance insufficient Uncontrolled slewing movement

Cause Electronic excavator control not activated / defective

• • • • •

•

• •

• • • • •

5-6

Superstructure holding brake applied Pressure-relief valve adjusted too low level / defective Servo system pump defective Malfunction in feed-pressure circuit of slewing pump Malfunction in high-pressure circuit of slewing system Malfuction of moment-regulating valve Malfunction in slewing pump displacement cylinder Excessive leakage in slewing motor

Check Adjust Replace Top up Reduce Clean 1) Contact the Bucyrus HEX Service Chapter ref.

Working

P E W A S R

P P 1) 1) 1) 1) 1) 1) 1)

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Annex Central lubricating system – Fault table Fault

Remedial action

Grease pump not working, the BCS does not indicate a warning Automatic circuit breaker on Grease pump not working, pilot lamp lit Grease pump working, no grease delivered Greasing pressure too high or too low

• • • •

Cause Timer defective

• • •

•

• • •

• • • • •

Lines between timer and hydraulic motor defective Hydraulikmotor defektive Grease pump defective Grease sieve clogged Distributor defective Grease container empty Grease pump does not suck grease Leaky lines Non-return valve defective Pressure switch defective

BA RH170B(3 725 013.00)-EN

Check P Adjust E Replace W Top up A Reduce S Clean R Vent L 1) Contact the Bucyrus HEX Service Chapter ref.

P/W P/W P/W P/W P/R P/W P/A P/L P/L P/W E

5-7

OPERATING INSTRUCTIONS RH170B Electric Annex HYDRAULIC CIRCUIT DIAGRAM Detailled information can be found in the „Technical Handbook“ chapter 8 or contact Bucyrus HEX Service.

5-8

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Annex ABBREVIATIONS A abt. acc.

Ah API approx.

Ampere (SI base unit of electric current) about according to Ampere hours (SI base unit of quantity of electricity) American Petroleum Institute approximately

BA bar Bh

= OI = Operating instructions unit of pressure, 1 bar = 14.5 psi = OH = Operating hour

CE

Communauté Européenne = European community Committee for european Construction Equipment (Defines a measure for bucket, grab or scoop filling) European Standardization Committee centimeter (= 1/100 m) Cubic centimeters per revolution counterclockwise clockwise

CECE

CEN cm cm3/rev CCW CW

dia.

DIN

Decibel (sound intensity according to measuring method A) Diameter German Industrial Standard

EDS eff. e.g. etc.

Electronic diagnostic system effective for example etcetera

Fig. FOPS FS ft

Figure, serial number of illustration Falling objects protective structures Rock shovel (working equipment) foot (unit of distance), 1 ft = 0.30 meter

gal GLR

gallon (unit of volume), 1 gal = 3.78 liters Full-load controller (electronic module for PMS)

HD Hydr.

Heavy duty Hydraulic, Hydraulics

i i.e.

IFN

id est = that is ISO service rating, blocked

dB(A)

Incl.

ISO

including, inclusive of International Standardization Organization

kg kg/dm3

Kilogram (unit of weight), 1 kg = 2.2 lb Kilograms per cubic decimeter (= unit of specific density) Kilometers per hour KiloNewtons per meter (1 kNm = 1000 Nm) = unit of torque Kilowatt (1 kW = 1.36 hp)

km/h kNm kW l lb Lb/in² LC LDA LED l/min LpA LS LwA

Liter (unit of volume), 1 liter = 0.26 gal pound (unit of mass), 1 lb = 0.45 kg Pounds per square inch (= psi) Long crawler Charge pressure-dependent full-load limiter Light-emitting diode Liters per minute Sound pressure at workplace Limited slip Sound power level of the machine in stationary operation

m MA mA max. min. min-1 mm

Meter (unit of distance), 1 m = 3.28 ft Tightening torque 1 Milliampere (= /1000 A) maximal, maximum minimal, minimum Revolutions per minute Millimeter (=1/1000 m)

N N, kN NLGI NLGI-Klasse Nm No.

Normal, standard version Newton, kiloNewton (unit of force) National Lubricating Grease Institute (USA) Consistency - lubricant classification acc. to DIN 51 818 Newtonmeter (unit of torque) Number

OH op.inst.

OW

Operating hour Operating instructions Superstructure

oz

ounce (unit of volume) 1 oz = 0.03 liter

Transmission ratio

BA RH170B(3 725 013.00)-EN

5-9

OPERATING INSTRUCTIONS RH170B Electric Annex ABBREVIATIONS PMS P/No.

Pump Managing System

PLC

Part number (Bucyrus HEX) Metric horsepower (1 PS = 0.74 kW) pund per sqare inch (unit of pressure), 1 psi = 0.069 bar Programmable logic controller

Qty.

Quantity

R, r resp.

RH ROPS rpm

Radius Respectively Crawler hydraulics (excavator) Roll-over protective structures Revolutions per minute (= min-1)

SAE sec./s.

SN SW

Society of Aotomotive Engineers (USA) Second Bucyrus HEX partnumber Width across flats

t TBG

typ.

Metric ton (= 1000 kg) Civil Engineering Employer's Liability Insurance Association Technical Handbook Backhoe dipper (attachment) Tons by meters (obsolescent unit of swing torque) Typical

U/min UW

Revolutions per minute Undercarriage

V VDMA

Volt (unit of electric voltage) Association of German Machinery and Systems Manufacturers

PS psi

THB TL tm

W

Watt (unit of electric power)

°C °F > <

Degrees Celsius (temperature) Degrees Fahrenheit (temperature) greater than less than

5-10

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Annex TECHNICAL DATA

BA RH170B(3 725 013.00)-EN

5-11

OPERATING INSTRUCTIONS RH170B Electric Annex

5-12

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Annex NOTES .............................................................................................................................................................................. .............................................................................................................................................................................. .............................................................................................................................................................................. .............................................................................................................................................................................. .............................................................................................................................................................................. .............................................................................................................................................................................. .............................................................................................................................................................................. .............................................................................................................................................................................. .............................................................................................................................................................................. .............................................................................................................................................................................. .............................................................................................................................................................................. .............................................................................................................................................................................. .............................................................................................................................................................................. .............................................................................................................................................................................. .............................................................................................................................................................................. .............................................................................................................................................................................. .............................................................................................................................................................................. .............................................................................................................................................................................. .............................................................................................................................................................................. .............................................................................................................................................................................. .............................................................................................................................................................................. .............................................................................................................................................................................. .............................................................................................................................................................................. .............................................................................................................................................................................. ..............................................................................................................................................................................

BA RH170B(3 725 013.00)-EN

5-13

OPERATING INSTRUCTIONS RH170B Electric Annex

5-14

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Index 6 INDEX Operating instructions

Part 1 INTRODUCTION FUNDAMENTAL SAFETY INSTRUCTIONS Part 2 OPERATION

Target group

Operating personnel + Inspection and servicing personnel + Repair personnel Operating personnel The operating personnel must have knowhow relevant to the operation and the application of this or comparable machines.

Part 3 INSPECTION AND SERVICING Part 4 REPAIR WORK

Inspection and servicing personnel The inspection and servicing personnel must have know-how relevant to the inspection and servicing of this or comparable machines.

Repair personnel The repair personnel must have know-how and experience relevant to the repair of this or comparable machines.

Part 5 ANNEX

Operating personnel + Inspection and servicing personnel + Repair personnel

Part 6 INDEX

Operating personnel + Inspection and servicing personnel + Repair personnel

BA RH170B(3 725 013.00)-EN

6-1

OPERATING INSTRUCTIONS RH170B Electric Index

6-2

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Index

A ABBREVIATIONS........................................... 5-10 ABBREVIATIONS............................................. 5-9 Access lighting................................................ 2-24 ACCIDENT PREVENTION REGULATIONS FOR ELECTRICALLY POWERED EXCAVATORS 112 After daily operation........................................ 2-85 Air conditioner (optional)................................. 2-73 Air intake filters ............................................... 3-98 ASSEMBLING WORKING EQUIPMENT SAFETY INSTRUCTIONS .......................... 2-86 Automatic fire-extinguishing system (optional 2-35 Avoid mixing of different hydraulic fluids ........ 3-31

B Battery ............................................................ 3-42 Battery main switch, switching and off .. 2-65, 3-43 Battery storage ............................................. 3-105 Bearing races.................................................. 3-87 Before starting work........................................ 2-83 Board-Control-System (BCS) ........................... 2-9 Braking the superstructure ............................. 2-83 Breather filter .................................................. 3-91 Breather filter, Clean / Replace ...................... 3-82 Breather filter, replace .................................... 3-57 Bypass valves (hydraulic oil reservoir) ........... 3-56

C Cab interior lamp ............................................ 2-28 CENTRAL LUBRICATING.............................. 3-89 Central lubricating system – Fault table ........... 5-7 Changing the gearbox oil....................... 3-75, 3-78 Changing the hydraulic oil .............................. 3-62 Checking the gas charging pressure in the pressure accumulator ............................. 3-86, 3-101 Checking the gearbox oil level / Topping up with oil................................................................. 3-70 Checking the greasing pressure............ 3-92, 3-93 Checking the hydraulic oil level ...................... 3-52 Circuit breaker, switching on and off .............. 2-69 Cleaning jobs .................................................. 3-13 Cleaning the electric motor............................. 3-39 Cleaning the hydraulic oil cooler .................... 3-67 Components ................................................... 3-13 Control Management System (CMS) ............... 2-8 Corrosion protection for pins and bearings (bushings and hubs)............................................. 2-88 CRAWLER TRACKS ...................................... 3-83

D Demand control / Zero-flow regulation ............. 2-9 Depressurizing the hydraulic system.............. 3-51 BA RH170B(3 725 013.00)-EN

DESCRIPTION OF THE EXCAVATOR............ 2-6 Design and function ........................................ 3-89 Designated use ................................................. 1-6 Drive.................................................................. 2-8 Driver's seat .................................................... 2-32

E Electric motor - Safety instructions ................. 3-39 Electric motor can not be switched on............ 2-68 Electric motor, greasing .................................. 3-40 Electrical system ............................................... 2-9 ELECTRICAL SYSTEM.................................. 3-41 Electrical system - Safety instructions ............ 3-41 Electrical system (24V), switching and off ...... 2-65 Electronic excavator control............................ 3-68 ELEKTRIc MOTOR......................................... 3-39 Emergency escape device (optional............... 2-36 Emergency lowering of the working equipmen2-85 EMERGENCY STOP switch........................... 2-30 Entering and leaving the machine, Safety instructions ............................................................. 2-24 Equipment, check for cracks .......................... 3-99 Escape ladder (optional)................................. 2-27 Excavator layout ............................................... 2-7 Extract from the German regulations............ 3-101

F FAULT TABLES................................................ 5-4 Filling............................................................... 3-91 Filling quantities - Grease ............................... 3-27 Filling quantities - oil ....................................... 3-30 Filling quantities - other................................... 3-30 Filter (control circuit) ....................................... 3-58 Fire and explosion hazard ..............1-14, 2-5, 3-11 Fire and Explosion Hazard ............................... 4-7 Fire extinguisher ............................................. 2-34 Floodlight projector, replacing the lamp.......... 3-49 Folding ladder (optional) ................................. 2-26 Function .......................................................... 3-90

G Gearbox - Checking the oil level / Topping up with oil ...............................................3-75, 3-77, 3-80 Gearbox venting..................................... 3-76, 3-79 Grease filter (Filling the grease container) ..... 3-96 Grease filter (Grease lines)............................. 3-97 Greases for bearings and slewing rings ......... 3-37

H Heating and air conditioning ........................... 3-98 High-pressure filter for working hydraulics ..... 3-59 High-pressure filters for swinging circuits ....... 3-61 High-pressure filters for the servo circuit ........ 3-60 Hose line for oil change .................................. 3-38 6-3

OPERATING INSTRUCTIONS RH170B Electric Index HYDRAULIC CIRCUIT DIAGRAM ................... 5-8 Hydraulic hoses – Instructions ......................... 4-8 hydraulic LADDER........................................ 3-100 Hydraulic motor chamber - Check the oil level / Top up with oil ............................................. 3-80 Hydraulic motor chamber, Changing oil ......... 3-82 Hydraulic oil cooler, cleaning.......................... 3-99 Hydraulic system .............................................. 2-8 HYDRAULIC SYSTEM ................................... 3-51 HYDRAULIC SYSTEM ..................................... 4-8 Hydraulic system - Safety instructions ........... 3-51

I Illuminating the control column ....................... 2-29 In case of failure ............................................. 2-68 Inspection and servicing - Safety instructions .. 3-5 Inspection and Servicing plans - Instructions . 3-13 INSPECTION PLAN - OIL .............................. 3-28 Inspection plan – Oil (Legend)........................ 3-29 Instructions on troubleshooting ........................ 5-3 Intervals .......................................................... 3-13

L Layout of the fault table .................................... 5-3 LUBRICANTS ................................................. 3-31 LUBRICATING CHART – GREASE ............... 3-26 Lubricating chart – Grease (legend)............... 3-26

M Measures .......................................................... 5-3 MONITORING, WARNING AND CONTROL ELEMENTS................................................. 2-40 Motor protection relay, function ...................... 2-71

N notes ............................................................. 3-107 Notes ..................................................... 1-15, 2-89 NOTES ........................................................... 4-11 NOTES ........................................................ 5-13 Notes on the selection of oils and greases..... 3-31

O Oil for hydraulic system .................................. 3-33 Oilfilter (hydraulic circuit grease pump) .......... 3-95 Oils / Greases ................................................. 3-13 Oils for combustion engines (On-Board Crane, optional) ...................................................... 3-32 Oils for pump gearbox .................................... 3-34 Oils for swing gearboxes ................................ 3-35 Oils for travel gearboxes................................. 3-36 ON-BOARD CRANE (OPTIONAL) ............... 3-102 On-Board crane, – blocking the boom in position of rest ........................................................ 3-104 On-board crane, checking ............................ 3-102

6-4

On-Board crane, checking tightness of fastening bolts ........................................................... 3-104 On-board crane, drive unit ............................ 3-103 On-board crane, monitoring, warning and control elements.................................................... 3-102 On-board crane, servicing ............................ 3-103 Operating Instructions, where to store it in the driver’s cab .................................................... 2-4 Operation - Safety instructions ......................... 2-3 Organizational measures.................................. 1-7 OTHER MAINTENANCE ................................ 3-98

P Plan A - E........................................................ 3-21 Plan N ............................................................. 3-17 Plan T and W .................................................. 3-19 Plan V ............................................................. 3-15 Possible causes................................................ 5-3 Pre-chamber / spur wheel section, Changing oil 381 Pre-chamber / spur wheel section, Check the oil level / Top up with oil................................... 3-80 Pre-chambers working pumps, draining oil, changing oil ................................................. 3-73 Preface.............................................................. 1-3 Pressure accumulator - Emergency lowering. 3-69 PRESSURE ACCUMULATORS - SAFETY INSTRUCTIONS ............................................... 4-9 Pressure-accumulator inspection regulations 3-86 Pressure-accumulator inspection regulations .... 3101 Pump Managing System (PMS) ....................... 2-8 PUMP TRANSFER GEARBOX ...................... 3-70 Pump transfer gearbox lube oil filter, replace . 3-74 Pump transfer gearbox, changing oil.............. 3-72 Pump transfer gearbox, checking pre chambers oil level ........................................................ 3-71 Pump transfer gearbox, venting...................... 3-72 Putting the excavator out of operation.......... 3-105 PUTTING THE EXCAVATOR OUT OF OPERATION AND RECOMMISSIONING ............. 3-105 PUTTING THE MACHINE INTO OPERATION .. 262

R Recommissioning ......................................... 3-105 Removing and installing the battery ............... 3-44 Repair instructions ............................................ 4-8 Repair work - Safety instructions...................... 4-5 Replacing the hydraulic oil return-flow filters (hydraulic oil reservoir ...................................... 3-54

S Safety instructions .......................................... 2-81 Safety instructions for excavators with electric motor .............................................1-13, 3-3, 4-3

BA RH170B(3 725 013.00)-EN

OPERATING INSTRUCTIONS RH170B Electric Index Safety instructions governing specific operational phases........................................................... 1-8 Section.............................................................. 5-3 Securing the machine..................................... 2-87 Selection and qualification of personnel; basic responsibilities............................................... 1-8 Service station (tanklift) .................................. 2-62 Servicing lighting............................................. 2-29 Servicing switch .............................................. 2-31 SERVICING WORK........................................ 3-38 Signs ............................................................... 2-11 SLEWING GEARBOX .................................... 3-75 Slewing mechnism – Fault table....................... 5-6 Slip ring maintenance ..................................... 3-48 Special work in conjunction with utilization of the machine and maintenance and repairs as well as troubleshooting during work; disposal of parts and consumables................................. 1-9 Stored Program Control (SPC)......................... 2-8 Superstructure .................................................. 2-8 Superstructure holding brake ......................... 2-79 SWING GEARBOX......................................... 3-77 SWING RING.................................................. 3-87 Swing ring - Instructions ................................. 3-87 Swinging ladder .............................................. 2-25 Swinging the superstructure ........................... 2-83 Switchgear cabinet ......................................... 3-45 Switching the electric motor on and off .......... 2-66

T TECHNICAL DATA......................................... 5-11 Time-out before restart ................................... 2-67 Track / support rollers, greasing..................... 3-84 Track drive – Fault table ................................... 5-5 Track parking brake........................................ 2-79

BA RH170B(3 725 013.00)-EN

Track roller / support roller, fastening ............. 3-84 Track tensioner ............................................... 3-85 Trainer's / instructor's seat.............................. 2-35 Transport - Safety instructions........................ 2-80 Transporting and recommissioning ................ 1-11 Transporting the machine ............................... 2-80 TRAVEL GEARBOX ....................................... 3-80 Travel gearbox, Changing oil....................... 3-81 Travelling ........................................................ 2-75 travelling the machine..................................... 2-74 Travelling, Safety Instructions......................... 2-74 TROUBLESHOOTING...................................... 5-3

U Unblocking a grease line. ............................... 3-94 Undercarriage ................................................... 2-8

V Venting the hydraulic system.......................... 3-66

W Warning of special dangers ............................ 1-10 Warnings and symbols ..................................... 1-5 Warranty ........................................................... 1-4 Welding operations - Safety instructions ........ 4-10 Windscreen washer ........................................ 2-31 Working........................................................... 2-84 Working equipment, avoid extreme positions. 2-82 Working hydraulics – Fault table ...................... 5-4 Working operatioN .......................................... 2-81 WORKING OPERATION ................................ 2-83

6-5

OPERATING INSTRUCTIONS RH170B Electric Index

6-6

BA RH170B(3 725 013.00)-EN