CAT 7295 Electric Rope Shovel Operators Manual - PDF DOWNLOAD

®

BI010535

July 2012

Operators Manual 7295 Electric Rope Shovel

OM11094-EN

SAFETY.CAT.COM

BI010535

Front of Machine

Model Cross Reference Chart

Serial Number Plate

Model Plate

Bucyrus Model

CAT Model

182M

7182

295 HD

7295 HD

295 HR

7295

395 HR

7395

495 HD

7495 HD

495 HR 495 HF

2

2

7495 7495 HF

Amendments and alterations to this publication are not subject to notification. Caterpillar Global Mining LLC reserves all rights to this publication. Its content is protected by copyright laws.

No part of this publication may be reproduced or transferred in any way or form without the prior written approval of Caterpillar Global Mining LLC. Caterpillar Global Mining LLC declines any liability for direct or indirect consequences of printing errors. © 2012 Caterpillar Global Mining LLC.

Operators Manual BI010535

Table of Contents About This Manual ...................................................................................................................... 5 Purpose ................................................................................................................................... 5 Organization ............................................................................................................................ 5 Revisions................................................................................................................................. 5 Precautions and Disclaimers .................................................................................................. 5 Terminology ............................................................................................................................. 6 Contact .................................................................................................................................... 6 Safety Symbols And Signal Words ............................................................................................. 7 Safety Precautions ..................................................................................................................... 9 General Precautions: ............................................................................................................. 10 Maintenance Precautions: ..................................................................................................... 11 Operating Precautions: ......................................................................................................... 12 Operation Near Electrical Power Lines ................................................................................. 13 Fire Prevention ...................................................................................................................... 14 Fire Extinguisher Locations ........................................................................................................ 15

Warning Signs And Decals .................................................................................................... 16 Stored Energy Decals ................................................................................................................ 17

Safety - Swinging Restraint & Ballast Box Support .............................................................. 18 Ballast Box Support ............................................................................................................... 18 Swinging Restraint ................................................................................................................ 19 Machine Overview ................................................................................................................... 21 Nomenclature ............................................................................................................................. 21

Lower Works .............................................................................................................................. 22 Truck Frame and Crawlers ......................................................................................................... 22

Crawlers ................................................................................................................................ 23 Crawler Assembly ...................................................................................................................... 23

Truck Frame .......................................................................................................................... 24 Swing Rack ........................................................................................................................... 25 Swing Rack and Roller Circle ..................................................................................................... 25

Roller Circle ........................................................................................................................... 26 Roller Circle Assembly ............................................................................................................... 26

Propel Machinery ................................................................................................................... 27 Collector Rings ...................................................................................................................... 28 Rotating Deck ............................................................................................................................ 30 Revolving Frame ................................................................................................................... 30 Center Pintle .......................................................................................................................... 30 OM11094-EN

7295 Electric Rope Shovel

1 July 2012

Operators Manual BI010535

Deck Extensions ................................................................................................................... 32 Deck Extensions and Ballast Box .............................................................................................. 32

Ballast Box ............................................................................................................................ 32 Machinery House ................................................................................................................... 33 Boarding Stairs ...................................................................................................................... 33 RH Boarding Stairs .................................................................................................................... 33

Retractable Boarding Ladder................................................................................................. 34 A-Frame ................................................................................................................................ 35 A- Frame and Front End Support Components ........................................................................... 35

Hoist Machinery ..................................................................................................................... 36 Hoist Machinery - Plan View ....................................................................................................... 36

Swing Machinery ................................................................................................................... 37 Swing Machinery Components .................................................................................................... 37

Crowd Machinery .................................................................................................................. 38 Crowd Machinery Components ................................................................................................... 38

Operator’s Cab ..................................................................................................................... 39 Compressed Air System ....................................................................................................... 40 Automatic Lubrication System ............................................................................................... 40 Lubrication Room ....................................................................................................................... 41

Lube Reservoir fill / Overflow Plumbing ................................................................................. 42 Lube Reservoir Fill / Overflow Plumbing ..................................................................................... 42

Front End Equipment ............................................................................................................... 43 Suspension Strands .............................................................................................................. 43 Boom ..................................................................................................................................... 44 Boom Assembly ........................................................................................................................ 44

Running Ropes ..................................................................................................................... 45 Ropes - General Arrangement .................................................................................................... 45

Saddle Block ......................................................................................................................... 46 Dipper Handle ........................................................................................................................ 47 Dipper .................................................................................................................................... 48 Dipper Assembly ........................................................................................................................ 48

Padlocks................................................................................................................................ 49 Left and Right Padlocks ............................................................................................................. 49

Dipper Trip ............................................................................................................................. 50 Dipper Trip Motor and Dipper Trip Sheave .................................................................................. 50

Operator’s Controls ................................................................................................................. 51 Location of the Operating Controls .............................................................................................51

Primary Operating Controls .................................................................................................. 52 Operator’s Control Consoles in the Cab ...................................................................................... 52

Controls on the Left Console ........................................................................................... 53 Left Joystick ............................................................................................................... 53 Dipper Trip ................................................................................................................. 53 Signal Horn ................................................................................................................ 54 Radio ......................................................................................................................... 54 Left Control Console .................................................................................................................. 54

Hoist Brake ................................................................................................................ 54 Crowd Brake .............................................................................................................. 54 2 July 2012

7295 Electric Rope Shovel

OM11094-EN

Operators Manual BI010535

Swing Brake .............................................................................................................. 55 Propel Brake .............................................................................................................. 55 Climate Control Panel ................................................................................................ 55 Windshield Wiper Switch .......................................................................................... 55 Windshield Washer Switch ....................................................................................... 55 Controls on the Right Console ........................................................................................ 56 Right Joystick ............................................................................................................ 56 Control Stop Pushbutton ............................................................................................ 57 Right Control Console ................................................................................................................ 57

Control Reset Pushbutton ......................................................................................... 58 Dig/Propel Transfer Switch .............................................................................................. 58 Emergency Stop Pushbutton ..................................................................................... 59 Main Power Off Pushbutton ....................................................................................... 59 Earth Continuity Lockout Pushbutton ........................................................................ 60 Telephone .................................................................................................................. 60 Operator’s Seat ......................................................................................................................... 61 Operator’s Seat - Front View ...................................................................................................... 61

Operator’s Display .................................................................................................................... 63 Operator’s Display Panel ............................................................................................................ 63

Display Area And Indicators ................................................................................................... 64 Display Screens .................................................................................................................... 65 Language Screen ....................................................................................................................... 65 Icon Screen ............................................................................................................................... 66 Active Alarm .............................................................................................................................. 67 Alarms Help ............................................................................................................................... 68 Rope Reeving/Pintle Tightening .................................................................................................. 69 Rope Reeving/Pintle Tightening Help .......................................................................................... 70 Calibration Limits ....................................................................................................................... 71 Limit Calibration Help ................................................................................................................. 72 Fault Counters/Operating Hours ................................................................................................. 73 PLC Menu Screen ...................................................................................................................... 74 PLC Main Screen ....................................................................................................................... 74 Operator’s Screen ...................................................................................................................... 75

Auxiliary Controls ...................................................................................................................... 76 Remote Start Console ........................................................................................................... 76 House Light Circuit Breakers................................................................................................. 78 Lighting Transfer Switch ........................................................................................................ 78 Lubrication Control Panel ...................................................................................................... 79 Windshield Wipers ................................................................................................................ 80 Windshield Washer ............................................................................................................... 80 Pre-start Checks ....................................................................................................................... 81 Walkaround Ground Level Inspection .................................................................................... 81 On-board Inspection .............................................................................................................. 82 Machine Start-up, Operation And Shutdown ......................................................................... 83 Start-up .................................................................................................................................. 83 Start-Up Control Locations ......................................................................................................... 83 OM11094-EN

7295 Electric Rope Shovel

3 July 2012

Operators Manual BI010535

Restarting After An Electrical Fault ........................................................................................ 85 Operation............................................................................................................................... 86 Machinery Motions ................................................................................................................. 87 Hoist Motion ..................................................................................................................... 87 Crowd Motion .................................................................................................................. 88 Propel Motion ................................................................................................................... 89 Propel - Straight Forward/Reverse .............................................................................................. 89

Swing Motion ................................................................................................................... 90 Proper Swing Motion ....................................................................................................... 91 Steering ........................................................................................................................... 93 Counter-rotation Turns .................................................................................................... 95 Positioning The Machine ......................................................................................................... 97 Back-up Method .................................................................................................................... 97 Drive-by Method .................................................................................................................... 98 Start Of The Dig Cycle .................................................................................................... 99 Force the Dipper Lip into the Bank .............................................................................................99 Variations on Dipper Penetration .............................................................................................. 101 Dig with the Dipper Beneath the Boom Point ............................................................................ 102

Engaging The Bank ....................................................................................................... 103 Make Effective Use of the Hoist Effort ..................................................................................... 103 Hoist Force Opposes Crowd Force ........................................................................................... 103

Slope Limitations ........................................................................................................... 106 Slope vs. Degrees .................................................................................................................... 106 Rollover and Operation Limits ................................................................................................... 107

Excavated Material .............................................................................................................. 108 Operation Checks ............................................................................................................... 109 Operating Hints ................................................................................................................... 110 Stopping The Machine ......................................................................................................... 111 Machine Shutdown .............................................................................................................. 111 General Estimated Component Weights .............................................................................. 112

4 July 2012

7295 Electric Rope Shovel

OM11094-EN

Operators Manual BI010535

About This Manual Purpose This manual is designed to assist the owner in the operation of your machine. Inside, you will find the following information: location and explanation of controls, instructions for machine operation, and certain maneuvering techniques.

NOTE:

This is not a maintenance manual. A separate, detailed maintenance manual for this machine has been supplied with the machine.

Organization •

A main table of contents (TOC) is your guide to topics and subtopics. It is located at the front of the manual.

Revisions This manual may be revised without notice. The most recent electronic version is available online.

Precautions and Disclaimers •

Carefully study and follow all procedures in this manual. Safety guidelines are intended to prevent accidents and are provided in the interest of all mine personnel. Overall safety depends on the use of good judgment and the alertness of the entire mining crew.

•

It is the owner/mine’s responsibility to perform the necessary risk assessment to outline proper safety precautions. A minimum of unplanned machine downtime and more reliable machine operation should result when a systematic and thorough maintenance/service procedure is adhered to for this machine.

•

It is the policy of the manufacturer to improve its products whenever possible and practical to do so. The company reserves the right to make changes or add improvements to its machines at any time. This will be without incurred obligations to install such changes on machines sold previously. Due to this ongoing program of product research and development some procedures, specifications and parts may be altered in a constant effort to improve our machines.

OM11094-EN

7295 Electric Rope Shovel

5 July 2012

Operators Manual BI010535

Terminology •

The terms left, right, front, and rear refer to machine locations as viewed by the operator sitting in the operator’s seat in the cab.

•

On the cover and at the bottom of each page there is an alphanumeric code to identify the manual, formatted as follows: XXnnnnnn-YY • XX represents the manual type. Below is a list of all manual types.

• nnnnnn represents the serial number for machine-specific manuals, or a generic manual number intended for several machines.

• YY represents the language code. Below is a list of common language codes.

Code

Type

Code

Language

SM OM EM PM TM ZM AM VM MM

Service Operation Electrical Parts book Troubleshooting Electrical training Addendum Vendor Miscellaneous

EN ES FR PT

English Spanish French Portuguese

For example, manual code EM141455-ES is an electrical manual written in Spanish for machine #141455.

Contact Should you require additional information or factory service assistance, contact your regional service representative or: Caterpillar Global Mining LLC 6744 S. Howell Ave. Oak Creek, WI, USA 53154 Telephone (+1) 414.768.4000

6 July 2012

7295 Electric Rope Shovel

OM11094-EN

Operators Manual BI010535

Safety Symbols And Signal Words The safety alert symbols displayed here and throughout this manual are used to call attention to instructions concerning personal safety. Carefully read and follow these instructions and observe all SAFETY, DANGER and CAUTION graphics mounted on various areas of the machine.

Be certain anyone servicing this machine is aware of these SAFETY SYMBOLS and their definitions.

If it is impossible to safely perform any of the enclosed maintenance and operational procedures, contact your regional service representative or the factory.

The following defines distinctions between safety instructions. In all these definitions the safety alert signal is used.

NOTE: This signal word denotes an item of required information pertaining to the equipment. A loss of time, assets, or minor injury may result if the appropriate action is not taken.

This signal word serves as a reminder of safety practices, or directs attention to specific safety practices which could prevent possible injury if precautions are not adhered to.

This signal word denotes an imminently dangerous hazard which will result in death, serious bodily injury, or serious damage to equipment if not acknowledged and appropriate action taken.

This signal word denotes an imminently dangerous electrical hazard which will result in death, serious bodily injury, or serious damage to equipment if not acknowledged and appropriate action taken.

Operating, maintaining or servicing this machine is dangerous unless performed properly. Each person must satisfy himself and his employer that he is alert, has the necessary skills, knowledge, proper tools and equipment for the task at hand. It is critical that all the methods used are safe and correct. Factory service representatives and specialists are available to provide additional information or technical assistance. The operator must be alert, physically fit and free from the influence of alcohol, drugs, or any medications that might impair his eyesight, hearing or reactions.

OM11094-EN

7295 Electric Rope Shovel

7 July 2012

Operators Manual BI010535

STORED ENERGY! Components on machine are heavy and removal of pins without proper preparation and precaution can cause serious bodily injury and/or damage to the front-end of the machine.

Safety must always be paramount!

Consult your supervisor when safety is in doubt.

8 July 2012

7295 Electric Rope Shovel

OM11094-EN

Operators Manual BI010535

Safety Precautions

This manual provides information and data for the maintenance and/or operation of this machine. All electrical equipment must be serviced by qualified individuals who have been properly trained to work with high voltage systems and variable frequency AC drives. Failure to comply could result in personal injury or death.

Do not attempt mechanical or electrical maintenance on this machine without a full understanding of each component’s operation and function. Components utilizing electrical power, air pressure, hydraulic pressure and compression or tension springs for operation must be deactivated and isolated prior to disassembly.

The FEEDER CABLE must contain a provision for a ground connection, especially whenever 2,300 volts or greater are used. At the substation, the power line must terminate (see paragraph on ground circuits) to a suitable permanent ground. At the machine, the power line must securely terminate through a bolted connection to the machine frame. This provides a constant ground for the machine and its electrical equipment. Failure to provide this adequate ground endangers employees and equipment.

HIGH VOLTAGE! The need for a power line grounding circuit adequate for the machine cannot be overemphasized. Without a good grounding system, high voltages exist between the machine and the ground. The portable trail cable and power lines supplying electric energy to the machine must have a ground wire, ample in capacity, running parallel to the main wires over the entire distance from the transformer to the machine. A suitable grounding system must be used at the transformer. Consult your local electrical supplier for details.

Due to the inherent dangers in the operation of high voltage electrical equipment, a safe grounding system is required that includes ground conductors in the cable, a neutral grounding resistor, and related relays and switchgear. A ground continuity check system is also recommended.

OM11094-EN

7295 Electric Rope Shovel

9 July 2012

Operators Manual BI010535

General Precautions: •

The employment of qualified maintenance personnel, through a scheduled maintenance program, is the best way to minimize machine downtime and maximize productivity of equipment.

•

Keep hands, feet and clothing away from rotating parts.

•

Wear a hard hat, safety shoes and protective lenses at all times.

•

Replace any and all safety and warning placards if they are defaced or removed from the machine.

•

Think before you act. Carelessness is one luxury the service man cannot afford.

•

Excessive or repeated skin contact with sealants or solvents may cause skin irritation. In case of skin contact refer to the Material Safety Data Sheet (MSDS) for that material and the suggested method of cleanup.

•

Inspect safety catches (keepers) on all hoist hooks. Do not take a chance, the load could slip off of the hook if they are not functioning properly.

•

If a heavy item begins to fall, let it fall, don’t try to catch it.

•

Keep your work area organized and clean. Wipe up oil or spills of any kind immediately.

Keep tools and parts off of the ground. Eliminate the possibility of a fall, slipping or tripping.

•

Floors, walkways and stairways must be clean and dry. After fluid draining operations be sure all spillage is cleaned up.

•

Electrical cords and wet metal floors make a dangerous combination.

•

Regularly inspect for any loose bolts or locking devices and properly secure them.

•

Use extreme caution while working near any electrical lines or equipment whether it be high or low voltage. Never attempt electrical repairs unless you are qualified.

•

Check limit switches for proper operation.

•

After servicing, be sure all tools, parts or servicing equipment are removed from the machine and secured in an appropriate storage area.

•

Mechanical Brakes are designed for use as static holding brakes only. Use as a motion (dynamic) brake in emergency situations only.

•

Use proper interior and exterior lighting.

•

Install and maintain proper grounding and ground fault protection systems.

•

Allow electrical inspection and maintenance to be performed only by a qualified electrician.

10 July 2012

7295 Electric Rope Shovel

OM11094-EN

Operators Manual BI010535

Maintenance Precautions: •

Do not wear rings, wristwatches or loose fitting clothing when working on machinery. They could get caught on moving parts causing serious injury.

•

Always wear a safety belt or harness when the danger of falling exists.

•

Always have a second person to monitor the lifeline when working in confined spaces.

•

Do not start an engine indoors unless adequate exhaust ventilators are provided and in operation.

•

Never utilize the machine air or hydraulic systems for support when working on the machine. Deactivate or isolate the entire system prior to performing maintenance.

•

Equipment should be parked on level ground at all times during machine servicing and periods of idleness.

•

Cranes and hoists must be of sufficient capacity to lift the heavier components (gearcases, etc.) Always work within the limitations of the equipment being utilized.

•

Be sure heavy items are properly rigged and supported from cranes or hoists before removing supporting members from the machine.

•

Utilize guide lines or ropes to minimize the swing of suspended heavy components.

•

Have sufficient service personnel available when removing or installing large heavy items to maintain control at all times.

•

Always use safety stands in conjunction with hydraulic jacks or hoists. Do not rely on the jack or hoist to carry the load, they could fail.

•

When disassembling a machine, be sure to use safety stands and adequate cribbing to prevent tipping or rollover of components.

•

When using an oxy/acetylene torch, always wear welding goggles and gloves. Keep a charged fire extinguisher within reach. Be sure the acetylene and oxygen tanks are separated by a metal shield and are chained to the cart.

•

Use pullers to remove bearings, bushings, gears, cylinder sleeves, etc. when applicable.

Use hammers, punches and chisels only when absolutely necessary. Always be sure to wear safety glasses.

•

Use extreme caution when using compressed air to dry parts. Use approved air blowguns, do not exceed 30 PSI (207 kPa), wear safety glasses or goggles and use proper shielding to protect everyone in the work area.

•

Be sure to promptly reinstall safety devices, guards or shields after adjusting and/or servicing the machine.

•

Protective eye goggles should be worn at all times when working on the air conditioning system. Work on the air conditioning system only in a well ventilated area.

•

Wipe away excess lubricants around bearings and gears. Never lubricate parts in motion.

OM11094-EN

7295 Electric Rope Shovel

11 July 2012

Operators Manual BI010535

•

Always wear approved rubber gloves and use insulated hooks or tongs when handling trail cable.

Operating Precautions: Wear hearing protection. It is recommended that operators wear hearing protection (ear plugs or ear muffs) when they are exposed to noise levels of 90 dBa and above for any time duration. Dual hearing protection (plugs and ear muffs) is recommended for any exposure to noise levels of 105 dBa and above, for any time duration. Exposure to noise levels of 115 dBa and above, at any time, requires dual hearing protection.

NOTE: The above recommendations are based upon U.S. Department of Labor, Mine Safety and Health Administration requirements, Title 30 CFR 62.0, which includes time weighted averages for exposure limits. At minimum, follow the requirements of your appropriate federal regulatory agency or your employer; whichever is most restrictive (most protects your hearing). Whenever in doubt about the noise level, wear approved hearing protection.

•

Do not attempt to get on or off the machine while it is in operation. Notify the operator prior to any attempt to board/exit the machine.

•

Always use proper communication methods (horn signals, radio, visual) to notify all personnel of your intentions before any equipment movement, and after equipment stop.

•

Do not move or operate the machine without first knowing the location and purpose of all personnel, test or support equipment, on or near the machine.

•

Do not allow unauthorized personnel on board the machine while in operation.

•

Use audible signals to warn of machine movements. A signal horn button is provided for this purpose.

•

Do not propel until the travel route has been cleared of obstructions.

•

Prevent trail cable from being dragged on the ground for long distances or at high speeds.

•

Do not propel the machine on a slope greater than that specified in the Operator’s Manual SLOPE LIMITATIONS.

•

Limit the amount of cable being pulled by the machine. Pulling too much cable will damage both the cable and the machine.

12 July 2012

7295 Electric Rope Shovel

OM11094-EN

Operators Manual BI010535

Operation Near Electrical Power Lines

HIGH VOLTAGE! The following precautions shall be complied with whenever operating around or near electrical distribution and transmission lines. Working in the vicinity of electrical power lines presents a very serious hazard and special precautions must be taken. For purposes of this manual we are considering the entire machine or its load, in any position, that can reach to within the minimum distance specified by local, state and federal regulations.

Safe operating practices require that you maintain the maximum possible distance from the lines and never violate the minimum clearances.

Before working in the vicinity of power lines, always take the following precautions: •

Always contact the owners of the power lines or the nearest electric utility before beginning work.

•

You and the electrical utility representative must jointly determine what specific precautions must be taken to ensure safety.

•

It is the responsibility of the user and the electric utility to see that necessary precautions are taken.

•

Consider all lines to be power lines and treat all power lines as energized even though it is known that the power is shut off and the line is visibly grounded.

•

Slow down the operating cycle. Reaction time may be too slow and distances may be misjudged.

•

Caution all ground personnel to stand clear of the machine at all times.

•

Use a signal person to guide the machine into close quarters. The sole responsibility of the signal person is to observe the approach of the machine to the power line.

The signal person must be in direct communication with the operator and the operator must pay close attention to the signals.

HIGH VOLTAGE! Death or injury could result should any part of the machine approach the minimum distance of an energized power line specified by local, state and federal regulations.

OM11094-EN

7295 Electric Rope Shovel

13 July 2012

Operators Manual BI010535

Fire Prevention •

Always have a “charged” fire extinguisher on hand and know how to use it. Inspect and service the extinguisher as indicated on its instruction plate.

•

DO NOT smoke while handling flammables or when near batteries.

•

Inspect all lines, tubes and hoses carefully. Tighten all connections to the recommended torque.

•

Repair or replace loose or damaged lines, tubes and hoses as soon as possible.

•

Make certain all clamps, guards and shields are replaced correctly so as to prevent vibration and the chafing of parts during operation.

•

DO NOT carry flammable fluids such as gasoline or solvents on board the machine.

•

DO NOT over-bend or strike pressurized lines or hoses. DO NOT install bent or damaged lines, tubes, or hoses. Replace them immediately.

•

DO NOT start the machine or move any of the controls if a warning tag is attached to the controls or the start panel.

•

Keep all cleaning rags properly stored. DO NOT discard them into a pile on board.

•

Keep all structural frame compartments, walkways and work areas clean and free of lubricant residue.

•

NEVER weld, burn, or perform service on the machine alone.

•

If a motor or other component is running hot, shutdown the machine until it has cooled and the cause is determined and repaired.

14 July 2012

7295 Electric Rope Shovel

OM11094-EN

Operators Manual BI010535

Fire Extinguisher Locations

OM11094-EN

7295 Electric Rope Shovel

15 July 2012

Operators Manual BI010535

Warning Signs And Decals The placards depicted are mounted on the machine as delivered from the manufacturer. These hazard warning placards convey information to operators, maintenance personnel, or anyone who will be on or near the machine. The information is designed to help prevent situations which may result in injury to personnel or damage to the machine.

DANGER TO PREVENT INJURY OR INJURY MAY RESULT FROM

DEATH CONTACTING ELECTRIC LINES

TO PLACE ANY PART OF THIS MACHINE OR LOAD WITHIN 10 FEET OF HIGH VOLTAGE LINES OF 50,000 VOLTS OR LESS FOR MINIMUM CLEARANCES OF HIGH VOLTAGE LINES IN EXCESS OF 50,000 VOLTS SEE YOUR LOCAL, STATE AND FEDERAL REGULATIONS 736444K1

TO BOARD MACHINE PULL CORD TO SOUND HORN. DO NOT LOWER BOARDING LADDER UNTIL MACHINE IS COMPLETELY STOPPED. C104093

DANGER

DANGER TO PREVENT INJURY

STAY CLEAR WHILE MACHINE IS OPERATING C102020

831905K1

TO PREVENT HEARING LOSS

TO PREVENT ACCIDENTS AND BODILY INJURY: THIS MACHINE SHALL ONLY BE OPERATED AND MAINTAINED BY TRAINED AND EXPERIENCED PEOPLE WHO HAVE READ AND UNDERSTOOD THE OPERATOR AND SERVICE MANUAL. IT IS THE USER’S RESPONSIBILITY TO FOLLOW THE MANUFACTURER’S INSTRUCTIONS ON MACHINE OPERATION AND APPLICATION AND TO OBSERVE ALL PERTINENT LAWS AND REGULATIONS.

WHEN EXPOSURE LIMIT IS REACHED FOR EXPOSURE LIMITS CONSULT LOCAL, STATE AND FEDERAL REGULATIONS 740168K1

signs_w

16 July 2012

COPIES OF THE INSTRUCTION MANUAL MAY BE OBTAINED BY WRITING TO THE BUCYRUS INT. CO., SO. MILWAUKEE, WI 638669K1

7295 Electric Rope Shovel

OM11094-EN

Operators Manual BI010535

Stored Energy Decals

OM11094-EN

7295 Electric Rope Shovel

17 July 2012

Operators Manual BI010535

Safety - Swinging Restraint & Ballast Box Support Ballast Box Support

Before performing any maintenance on the mining shovel, it should be resting on a firm, level surface.

Any mining shovel field work that requires the removal or lowering of the boom must incorporate additional support of the ballast box. The supports may be wooden cribbing or steel structures.

Two supports positioned side-by-side on level ground are recommended. These supports are intended to accept vertical loads only. To prevent machine rotation use the swing brakes, cable stays, welded ties, etc. Refer to “SWING RESTRAINT”.

When electric-powered, cable-style mining shovels are properly ballasted and operational, the center of gravity for the machine's upper works lies within the roller circle area. This assumes that the boom is attached to the machine and in its elevated, working position. As such, the machine should not be prone to tipping.

Boom removal or lowering will cause the center of gravity to shift toward the ballast box, decreasing machine stability. Stability is further dependent on the orientation of the upper works relative to the undercarriage. The machine may tip more easily over one of the four quadrants of the crawler mounting than it may over others.

Normally the machine is more likely to tip over the rear-most lower-roller than over the side of a crawler. Therefore, with the boom removed and the ballast box sitting over the rear of the crawlers, the machine may be unstable. Because ballast quantities differ from machine to machine and model to model, it is recommended that the ballast box be supported before beginning any procedure to lower and/or remove the boom.

18 July 2012

7295 Electric Rope Shovel

OM11094-EN

Operators Manual BI010535

Swinging Restraint

Before performing any maintenance on the mining shovel, it should be resting on a firm, level surface. A small ground slope is enough to cause the machine to freely rotate if the brakes are not set or other restraints are not used. Once moving, it will keep going.

The following shows the relation between an out-of-level or slope and the resulting difference in elevation over a 14 ft. swing rack: Slope

%

Difference in Elevation

0.25o

0.4%

0.75”

1.0o

1.7%

2.9”

5.0o

8.7%

14.7”

Where possible, all work on the swing brakes, motors, gearcases, or rack pinions should occur with the dipper attached to the machine and the full weight of the dipper on the ground. If the dipper is not resting firmly on the ground, then an external means of preventing machine upper works rotation is required. The preferred method to prevent machine rotation is to use a pair of one inch diameter steel cables to tie the upper works to the lower works. Other alternatives such as welded plates etc. can also be used. Contact your regional service representative or the manufacturer.

Mining shovels rotate using multiple swing units. Power is transferred from electric motors through individual gearcases, to pinions and into a fixed swing rack. Electric motor control prevents inadvertent machine rotation during operation. Should machine electric power be lost, spring-set brakes on the swing drive motors lock the geartrain to prevent machine rotation.

When working on the brakes, motors, or geartrains, it is an accepted practice to set the dipper on the ground. The weight of the dipper and handle will prevent machine rotation. EVEN IF ALL BRAKES, MOTORS, OR SWING GEARCASES ARE REMOVED the machine should not rotate.

In certain circumstances it may not be possible to rest the full weight of the dipper firmly on the ground. For instance, the dipper, handle or the boom may not be attached to the machine.

To prevent machine rotation, with any of the major structures removed, two swing motor brakes should be set. A single brake in good operational condition is acceptable. However, a minimum of two brakes is recommended due to the possibility that the proper operation of a single brake may be unknown.

OM11094-EN

7295 Electric Rope Shovel

19 July 2012

Operators Manual BI010535

ON MACHINES USING PLANETARY DUAL-OUTPUT SWING DRIVES, BOTH SWING PINIONS PER DRIVE MUST BE ENGAGED WITH THE SWING RACK IN ORDER FOR THE SWING BRAKE TO BE EFFECTIVE. The internal differential drive in the gearcase allows one pinion to rotate, even if the brake is set, when the other pinion has been removed.

An external means of preventing machine rotation must be used - if the dipper is not resting firmly on the ground and if any of the following are true: •

Two brakes are not effectively set and coupled to the motors, or

•

The motors and geartrain are not fully coupled to the swing pinions, or

•

The swing pinions are not engaged to the swing rack.

The preferred method to prevent machine rotation is to use a pair of one inch diameter steel cables to tie the upper works to the lower works. Other alternatives such as welded plates etc. can also be used. Contact your regional service representative or the manufacturer.

20 July 2012

7295 Electric Rope Shovel

OM11094-EN

Operators Manual BI010535

Machine Overview This mining shovel is designed and constructed to provide efficient service under the most severe conditions. The machine is built to the highest possible standards and will provide trouble free operation if properly maintained. This section of the manual introduces the machine and its functional capabilities and limitations.

Boom Point Sheaves

Crowd Half Sheave

Suspension Strands Electrical Control Room Filter

Machinery House

House Filter

Equalizers

Crowd Rope

Air Conditioner A-Frame

Operator’s Cab

Boom Shipper Shaft Saddle Block Retract Rope

Swing Machinery Boarding Stair Crawler Assembly

Dipper Handle Dipper Trip Rope Boom Pitch Bumper Brace

Swing Rack

Dipper Door Snubbers

Retract Rope Take-Up Mechanism

Hoist Ropes Padlocks

Dipper

Dipper Door 141402_nm

Nomenclature

OM11094-EN

7295 Electric Rope Shovel

21 July 2012

Operators Manual BI010535

Lower Works The lower works is comprised of the truck frame, right and left crawler frames, crawler belts, propel machinery, swing rack and roller circle.

Truck Frame and Crawlers

22 July 2012

7295 Electric Rope Shovel

OM11094-EN

Operators Manual BI010535

Crawlers This machine is provided with a crawler system composed of 2 independently-driven crawler frame assemblies, one on each side of the truck frame. Each crawler has its own belt driven by a sprockettype drive tumbler. Individual crawler links are heavy alloy steel castings connected by heat treated pins. Innovative drive tumblers made from large diameter steel castings have lugs extending beyond the tumbler rims. They are mounted on forged alloy steel shafts which turn on large anti-friction bearings mounted within the crawler frame. The sprocket type lugs provide a large area of contact against the crawler links, extending the life of both links and tumblers.

Lower rollers rotate on forged steel shafts mounted within the crawler side frames. Eight smaller rollers and 1 large roller per frame are specially suited to withstand the periodic single point ground reaction caused by uneven pit floors. Slide bars on top of each frame support the upper crawler belt, reducing propel friction and drag. These side frames are stress relieved weldments comprised of steel castings and cold weather steel plates. The crawler assemblies are bolted to the truck frame with large diameter rods and torque nuts. Each crawler belt can be independently adjusted for tension.

Crawler Assembly

OM11094-EN

7295 Electric Rope Shovel

23 July 2012

Operators Manual BI010535

Truck Frame The truck frame is a stress relieved welded cellular box structure which utilizes impact resistant steel in the major load carrying members. The low temperature toughness of the steel assures adequate strength and durability across a wide range of temperatures frequently encountered in machine applications. A fabricated support structure welded integrally into the truck frame supports the center pintle hub area.

The inner diameter of the hub is machined to accept the center pintle bushing. Truck frame surfaces which mate to crawler side frames and swing rack are shop machined to assure proper alignment and solid foundation.

24 July 2012

7295 Electric Rope Shovel

OM11094-EN

Operators Manual BI010535

Swing Rack The swing rack is a large diameter external tooth gear mounted on the top of the truck frame concentric with the center pintle bore. The rack is a 4-piece gear bolted to the truck frame.

Swing Rack and Roller Circle

OM11094-EN

7295 Electric Rope Shovel

25 July 2012

Operators Manual BI010535

Roller Circle The roller circle is composed of the upper rails, lower rails, thrust rails, 54 tapered rollers and inner/ outer roller cages. The lower rail segments are secured to the top surface of the swing rack forming a continuous rolling path for the rollers. The upper rails are attached to the bottom of the revolving frame, fore and aft of the center pintle. Upper rail ends are tapered to provide a smooth approach for the rollers. Rollers are tapered to ensure non-skid contact with rails. The rollers are spaced and aligned with pins and low maintenance polyurethane bushings.

Roller Circle Assembly

26 July 2012

7295 Electric Rope Shovel

OM11094-EN

Operators Manual BI010535

Propel Machinery The propel machinery is driven by two AC motors, each horizontally mounted to the crawler frames.

Each motor is coupled to a right-angled planetary gearcase high up off the pit floor for protection from water and rock damage. One spring-set, air-released, disc brake is mounted to each of the two motors. The dual planetary configuration with separate drive motors permits straight ahead or reverse propel as well as counter rotation steering.

OM11094-EN

7295 Electric Rope Shovel

27 July 2012

Operators Manual BI010535

Collector Rings High voltage collector rings between the revolving frame and truck frame transfer electric power from the truck frame to the rotating deck. Electric power enters the truck frame between the propel motors and is transferred by means of collector ring shoes to the collector rings. The shoes are mounted between the cast center pintle hub and the swing rack. The low voltage collector rings transfer power from the revolving frame back to the propel motors. The propel collector rings provide control to the propel motors and power for the propel blower motor.

28 July 2012

7295 Electric Rope Shovel

OM11094-EN

Operators Manual BI010535

Collector Rings - Propel and Low Voltage (Rear Section View)

OM11094-EN

7295 Electric Rope Shovel

29 July 2012

Operators Manual BI010535

Rotating Deck The rotating deck consists of revolving frame, center pintle, right and left deck extensions, operator’s cab and the machinery house. Also included are the electrical system components, operating controls, air system, A-frame, along with the hoist, swing and crowd machinery units.

Revolving Frame The revolving frame is the main structural member of the rotating deck. It is a welded, stress relieved structure with integral lugs for mounting the A-frame, crowd machinery and boom. Provisions are made for mounting deck extensions, operator’s cab, ballast box and swing gearcases. Machined pads on the deck locate the hoist drive motor and machinery frames.

Refer to the following page for a view of the revolving frame assembly with deck extensions and ballast box.

The revolving frame is connected to the truck frame by the center pintle.

Center Pintle The center pintle is a large diameter, hollow cylindrical forging with a flange at the top. It is threaded at the bottom with a lower locknut used to hold it in place. A bronze coated steel core spherical thrust washer between the lower locknut and the bottom surface of the truck frame provides a wear surface for pintle loads. The upper locknut at the top of the center pintle is doweled and bolted to the revolving frame to keep the center pintle from rotating.

The hollow pintle provides passage for air and grease lines and electrical cables from the revolving frame to the lower works using a swivel and collector ring assembly.

30 July 2012

7295 Electric Rope Shovel

OM11094-EN

Operators Manual BI010535

OM11094-EN

7295 Electric Rope Shovel

31 July 2012

Operators Manual BI010535

Deck Extensions Right and left side deck extensions are bolted to each side of the revolving frame. They provide a mounting area for the electrical transformers and accessory machinery as well as supporting the machinery house walls.

Deck Extensions and Ballast Box

Ballast Box The ballast box is an all-welded steel fabrication located at the rear of the main revolving frame. A series of vertical plates in the box form compartments for holding ballast.

32 July 2012

7295 Electric Rope Shovel

OM11094-EN

Operators Manual BI010535

Machinery House The machinery house encloses the revolving frame, ballast box and deck extensions. It is constructed of self-supporting steel panels with built-in framing. Removable roof sections are provided over the swing machinery and to the side and rear of the A-frame. The house also provides mounting for the air ventilation and pressurization system. A separate electrical room is located over the ballast box. Platforms and stairs facilitate access to the sides and tops of the house for inspection and maintenance purposes. Boarding stairs permit easy access onto the machine.

Boarding Stairs A set of boarding stairs is attached to the machinery house platform on the right side of the machine.

When lowered, the stairs allow entrance to the machinery house from ground level. To lower the stairs, a chord attached to the stairway is reachable from the ground. The stairs must be in the raised position to enable the operator’s controls.

RH Boarding Stairs

OM11094-EN

7295 Electric Rope Shovel

33 July 2012

Operators Manual BI010535

Retractable Boarding Ladder A vertical, retractable boarding ladder is attached to the machinery house platform on the left side of the machine. After use, the ladder automatically returns to its stored position aided by two 200 lb. counterweights that move vertically inside the ladder’s channels.

34 July 2012

7295 Electric Rope Shovel

OM11094-EN

Operators Manual BI010535

A-Frame An A-frame with seamless tubular alloy steel front legs provides ample space for the retracted dipper handle end. The rear legs are cold weather steel fabricated beams. Both front and rear legs are pin connected to lugs integral with revolving frame. The A-frame supports the boom via structural strands.

A- Frame and Front End Support Components

OM11094-EN

7295 Electric Rope Shovel

35 July 2012

Operators Manual BI010535

Hoist Machinery The hoist machinery consists of a motor coupled to two gear reductions which drive the hoist drum. A spring-set, air-released disc brake is mounted to the motor. A hoist rotary encoder limits hoist travel. The hoist motor is connected to the motor pinion shaft by a multiple coupling shaft assembly.

The first reduction gear set is mounted in an oil lubricated, totally enclosed gearcase. The second reduction gears are drip lubricated with open gear lubricant from the automatic lubrication system.

All shafts run on anti-friction bearings. The hoist bull gear is bolted to a spider on the left hand side of the drum.

The hoist drum is manufactured with machined, flame hardened rope grooves. Drum spider stub shafts turn on anti-friction bearings supported by side frames which are bolted to the rotating deck.

Hoist Machinery - Plan View 36 July 2012

7295 Electric Rope Shovel

OM11094-EN

Operators Manual BI010535

Swing Machinery

Swing Machinery Components

The swing machinery is mounted on both the left and right sides of the revolving deck. Each machinery installation consists of a blower-cooled electric motor mounted vertically on top of the gearcase. The motor drives the gear system through a single input coupling. Each swing motor is equipped with a spring-set, air-released disc brake. The gearcase includes injectors that provide positive lubrication to the critical bearing surfaces of the gearcase. The gearcase transmits torque to a single pinion shaft. The pinion at the bottom of the shaft meshes with the swing rack on the lower works.

OM11094-EN

7295 Electric Rope Shovel

37 July 2012

Operators Manual BI010535

Crowd Machinery The crowd machinery is located at the front, center of the revolving frame. It consists of a motor, spring-set, air-released disc brake, drum and gearing. A crowd limit switch prevents overtravel of the dipper handle. The entire machinery unit can be removed from the machine should maintenance or overhaul become necessary.

Crowd Machinery Components

The crowd drum drives the crowd and retract rope system. Rope grooves are machined into the drum and flame hardened. The crowd and retract ropes are attached to the drum by ferrule-becket anchors which greatly simplifies rope changes.

A spring set, air released disc type brake is mounted to the RH gearcase and connected to the crowd motor using a motor coupling assembly.

38 July 2012

7295 Electric Rope Shovel

OM11094-EN

Operators Manual BI010535

Operator’s Cab The isolated and elevated operator’s cab at the right, front of the machinery house provides a comfortable, safe and efficient working environment for the operator. Sufficient space is provided for the fully adjustable operator’s seat, a helper’s seat and the standard operator’s display panel.

The cab is sound and heat insulated with interior walls made of a sound deadening steel-plasticsteel composite. Electric powered windshield wipers are provided for quiet, dependable operation.

A one-piece front window is supplied in a rugged, easy-to-change frame. Transparent sun shades are provided in front and side windows.

An air conditioner and pressurizing unit utilizes environmentally friendly 134a refrigerant in the cooling system. Interior ducting distributes the airflow to best suit the comfort of the operator.

OM11094-EN

7295 Electric Rope Shovel

39 July 2012

Operators Manual BI010535

Compressed Air System The compressed air system consists of a rotary screw type air compressor, air receiver, air brakes, controls and center pintle air swivel. Hydraulic high pressure hose is used throughout. The air system is used to operate all machinery motion brakes and lubrication components and to perform various other functions.

Automatic Lubrication System The lube system is located in an insulated, double wall, lube room which can be heated for cold weather operation. A one ton (907 kg) monorail-mounted electric chain hoist is provided to be used to raise supplies from the ground onto the left house platform and into the lube room. Lube points on the roller circle rollers, electric motors, suspension rope pins and some dipper pins are manually accessed. All other lube points are fed from the automatic system or by oil bath.

40 July 2012

7295 Electric Rope Shovel

OM11094-EN

Operators Manual BI010535

A single-line automatic lubrication system applies open gear lubricant (OGL) and grease via a programmable logic controller (PLC). The system has four lube pumps (two for OGL and two for grease), each feeding individual PLC controlled circuits. Lincoln 75:1 air powered pumps are mounted on each of the two 85 gallon reservoirs. High pressure hoses with reusable fittings are utilized.

Lubrication Room

The four separately controlled lube circuits provide selective distribution frequency and quantity resulting in reduced lubricant usage and cost.

OM11094-EN

7295 Electric Rope Shovel

41 July 2012

Operators Manual BI010535

Lube Reservoir fill / Overflow Plumbing

Lube Reservoir Fill / Overflow Plumbing

The lube reservoir fill/overflow plumbing is located in the support structure directly below the lube room at the front, left side of the machine. Lubricants can be added at this location. The overflow connections are also located here. DO NOT plug the overflow connections.

42 July 2012

7295 Electric Rope Shovel

OM11094-EN

Operators Manual BI010535

Front End Equipment The front end equipment consists of the boom, the boom point sheaves, padlock, saddle block, dipper handle, dipper, dipper trip mechanisms, running ropes and boom suspension strands.

Suspension Strands The suspension strands are designed to maintain the proper boom angle. These are fixed-length strands that support the entire weight of the boom and the load.

OM11094-EN

7295 Electric Rope Shovel

43 July 2012

Operators Manual BI010535

Boom The boom is a welded steel structure consisting of twin box girders integrally connected at the boom point and in the lower section between the shipper shaft and boom feet. Impact resistant steel is utilized, coupled with 100% penetration and UT quality welds on all main splice joints.

Design optimization has resulted in heavier outside skin plates, minimizing the need for internal diaphragms. This reduction in weld related stress concentrations further enhances structural life.

Open manholes have been incorporated in the boom as a standard feature permitting periodic structural inspection. Integral “ladders” within the upper boom sections permit internal access without lowering the boom.

Boom Assembly

The boom is supported by four pre-stressed suspension (structural) strands attached to equalizer links on the A-frame. These inherent long life structural strands carry the working loads of the front end equipment. A boom limit switch with soft setdown prevents boom jacking shock loads.

44 July 2012

7295 Electric Rope Shovel

OM11094-EN

Operators Manual BI010535

Running Ropes Hoist, crowd, retract and dipper trip ropes are all plastic impregnated for increased life and for sheave and drum grooving life enhancement. The double twin hoist ropes are attached to the center of the hoist drum using ferrule-becket anchoring for faster rope change out. Each rope passes over a boom point sheave through the padlock and back over the boom point sheave to the hoist drum. The dual twin hoist rope configuration stabilizes the dipper while digging by attachment to the outer edges of the dipper body.

Ropes - General Arrangement

Crowd and retract ropes are attached to the crowd drum and work as an integral system. As the crowd rope is wound on to the drum, the retract rope is reeled off.

OM11094-EN

7295 Electric Rope Shovel

45 July 2012

Operators Manual BI010535

Saddle Block The saddle block is positioned between the boom side girders in the mid-section of the boom. It pivots on manganese-bronze bushings about the shipper shaft. It acts as a guide for the longitudinal movement of the dipper handle. The free-floating design of the handle in the saddle block eliminates handle torsion.

46 July 2012

7295 Electric Rope Shovel

OM11094-EN

Operators Manual BI010535

Dipper Handle The dipper handle assembly is a weldment consisting of a large diameter tube and a handle end where the machine’s dipper is attached.

The handle has a take-up mechanism that removes slack from the retract rope during operation. At the rear of the assembly is a fixed half-sheave for the crowd rope. The dipper tube moves in and out within the saddle block during operation.

OM11094-EN

7295 Electric Rope Shovel

47 July 2012

Operators Manual BI010535

Dipper A general purpose dipper is usually constructed as a casting and plate weldment. The dipper lip and lower front are alloy heat treated castings. The dipper body, back, upper sides and door are made of steel plate. Removable tooth adapters and replaceable tooth points are attached to the lip casting to penetrate the bank material.

The door is hinged and latched to the dipper body. A dipper trip mechanism controls the release of the latch bar, allowing the door to swing open. The latch bar holds the door shut during digging.

Spring loaded snubbers dampen the door’s swinging action.

Dipper Assembly

48 July 2012

7295 Electric Rope Shovel

OM11094-EN

Operators Manual BI010535

Padlocks Padlocks connect the hoist ropes to the outer edges of the dipper while still permitting fore and aft and sideways movement.

Left and Right Padlocks

OM11094-EN

7295 Electric Rope Shovel

49 July 2012

Operators Manual BI010535

Dipper Trip The dipper trip is a wire rope activated dipper door trip mechanism driven by 2 electric motors through gear reduction mounted on the boom near the boom foot.

Dipper Trip Motor and Dipper Trip Sheave

50 July 2012

7295 Electric Rope Shovel

OM11094-EN

Operators Manual BI010535

Operator’s Controls

Location of the Operating Controls

The operator must become familiar with the machine and its operating controls. The preceding figure depicts the general location of controls on the machine.

The operating controls will be grouped as primary and secondary controls, depending upon their location. The primary controls are the controls located in the operator’s cab and the secondary controls are the controls located in the machinery house.

The descriptions listed should familiarize the operator with each control’s location and functional use. The terms left, right, forward and reverse indicate directions with the operator seated in the cab, facing forward, with the boom extending over the take-up axle of the crawlers.

OM11094-EN

7295 Electric Rope Shovel

51 July 2012

Operators Manual BI010535

Primary Operating Controls

Operator’s Control Consoles in the Cab

52 July 2012

7295 Electric Rope Shovel

OM11094-EN

Operators Manual BI010535

Controls on the Left Console Left Joystick

omsL1346

The Left Joystick controls the crowd/horn/dipper trip and propel. It is the vertical handle mounted on the left console of the operator’s seat. This joystick will spring return to neutral when released.

During normal operation, pushing the joystick forward will extend the dipper handle and dipper into the bank. Pulling the joystick rearward will retract the dipper handle and dipper toward the machine.

The neutral position between the crowd and retract functions is defined by a detent that is easily felt. The rate of motion is controlled by varying the distance the joystick is moved from the neutral (center) position. Full forward or full rearward position provides maximum speed to the handle.

Moving the joystick to neutral will cause a braking action slowing the crowding or retracting handle.

Reversing the joystick will cause the motion to stop and if the joystick is held in this position, it will change the direction of the motion.

With the propel transfer switch in the PROPEL position, pushing the joystick forward will cause the left crawler to move forward. Pulling the joystick to the rear will cause the left crawler to move in the reverse direction. The crowd/retract motion is locked out electrically when the machine is in the propel mode.

Refer to JOYSTICK CONFIGURATION in this section of the manual to view the standard and alternate configurations for the Right and Left Joysticks.

Dipper Trip The dipper trip is part of the left joystick function in the standard configuration. Moving the joystick to the right will activate the dipper trip mechanism which releases the dipper door latch. The dipper trip is operational throughout the entire range of the crowd motion.

OM11094-EN

7295 Electric Rope Shovel

53 July 2012

Operators Manual BI010535

Signal Horn Moving the Left Joystick (in the standard configuration) to the left will activate the signal horn. The signal horn is operational throughout the entire movement range of the crowd motion.

Radio The radio supplied with your machine is an AM/FM Stereo radio with cassette player.

Left Control Console

Hoist Brake A selector switch used to set or release the Hoist Brake.

Crowd Brake A selector switch used to set or release the Crowd Brake.

54 July 2012

7295 Electric Rope Shovel

OM11094-EN

Operators Manual BI010535

Swing Brake A selector switch used to set or release the Swing Brake.

Propel Brake A selector switch used to set or release the Propel Brake.

Climate Control Panel The Climate Control Panel contains a rheostat controller on the top portion of the panel which is used to tailor the temperature of the air delivered to the operator’s cab within the selected mode of operation.

The Mode switch is provided to set the basic mode of operation for the roof mounted air conditioning/ heater unit.

The Blower Speed switch controls the volume of air being moved by the unit.

Windshield Wiper Switch The windshield wiper switch controls the speed of the wipers, as well as the starting and stopping of the wipers.

Windshield Washer Switch The windshield washer switch controls the supply to the washer reservoir which powers the washers.

OM11094-EN

7295 Electric Rope Shovel

55 July 2012

Operators Manual BI010535

Controls on the Right Console Right Joystick

omsR1346

The Right Joystick controls the hoist/swing and propel. It is a joystick mounted on the right console of the operator’s seat. The joystick is used to control the hoist, swing and right crawler motions of the machine. The position of the propel transfer switch will determine whether this joystick controls the hoist motion or the crawler motion.

With the propel transfer switch in the dig position, and during normal operation, pushing the joystick forward will lower the dipper. Pulling the joystick to the rear will hoist the dipper. The neutral position between the hoist and lower functions is defined by a detent that is easily felt. The speed of moving the dipper is controlled by varying the distance the joystick is moved from the neutral (center) position. The full forward or full rearward position provides maximum speed to the dipper. Moving the joystick to neutral will cause a braking action slowing the hoisting or lowering motion. Reversing the joystick will cause the motion to stop and if the joystick is held in this position, it will change the direction of the motion.

NOTE: When the right joystick is used in the hoist/lower mode it is a spring returned switch.

That is, it will return to the neutral position when it is released.

Moving the joystick to the left from the neutral position will cause the machine to swing to the left.

Moving the joystick to the right will cause the machine to rotate to the right. The swing motion is operational throughout the entire movement range of hoisting or lowering the dipper. The swing rate of acceleration is controlled by varying the distance the joystick is moved from the neutral position.

Moving the joystick to the neutral position will not stop the swing motion but will allow the machine to coast. To stop or change direction the control joystick is moved past the neutral point in the opposite direction. The rate of deceleration is controlled by varying the distance the joystick is moved from the neutral position in the opposite direction.

Refer to JOYSTICK CONFIGURATION in this section of the manual to view the alternate configurations for the Right and Left Joysticks.

56 July 2012

7295 Electric Rope Shovel

OM11094-EN

Operators Manual BI010535

With the propel transfer switch in the propel position, pushing the joystick forward will cause the right crawler to move forward. Pulling the joystick to the rear will cause the right crawler to move in the reverse direction. The hoist motion is locked out electrically when the machine is in the propel mode.

NOTE: When the JOYSTICK is used in the swing mode the switch is a spring returned switch.

That is, it will return to the neutral position when it is released.

Control Stop Pushbutton The control stop pushbutton is a pushbutton located on the right operator’s console. Normally it is used to de-energize controls after the machine has been safely stopped by placing motion controls in neutral.

Right Control Console

Actuation of this pushbutton when motions are running will cause all motions to automatically electrically brake to a stop and, when the motion speed has reached less than 5% speed, set all mechanical brakes. If the motions are already stopped, the brakes will be set and power is removed immediately. A similar switch is located on the front panel of the PLC control cabinet that can be used during testing of the machine.

OM11094-EN

7295 Electric Rope Shovel

57 July 2012

Operators Manual BI010535

THE OPERATOR SHOULD NEVER LEAVE THE OPERATOR’S SEAT BEFORE PRESSING THE CONTROL STOP PUSHBUTTON. Setting only the mechanical brakes with individual switches is not a sufficient safeguard to prevent machine damage and/or personnel hazards.

Control Reset Pushbutton

This is not an automatic reset system. All controls must be returned to neutral before the control reset button is pushed.

The control reset pushbutton is a pushbutton located on the right operator’s console. The reset pushbutton restores control to all motions if no additional faults exist. This pushbutton is inoperative until the main power start control has been actuated.

If a control fault occurs that shuts down a motion, all motions will automatically be shut down together. At this time the operator should set all brakes. If the fault clears, the motion may be reset by pressing this pushbutton. If the fault does not clear, the unfaulted motions can be restarted by pressing this pushbutton to enable these motions to re-position themselves.

Dig/Propel Transfer Switch The Dig/Propel Transfer Switch is used to switch between the two primary operating modes of the machine. The current mode of operation will be indicated on the Operator’s screen on the Operator’s Display.

• WHILE IN THE DIG MODE, THE PROPEL CONTROLS ARE DISABLED. • WHILE IN THE PROPEL MODE, THE DIG CONTROLS ARE DISABLED. The recommended procedure to transfer from dig to propel is to bring all motions to a controlled stop by the operator. Turn the hoist brake switch to the SET position and then press the control stop pushbutton. Turn the transfer switch from DIG to PROPEL. When the indicator on the Operator Display screen indicates that the transfer has been completed, turn the propel brake switch to release.

58 July 2012

7295 Electric Rope Shovel

OM11094-EN

Operators Manual BI010535

Emergency Stop Pushbutton The machine stop/emergency stop pushbutton is located on the right operator’s console. It is used to remove power from the machine motions after the motions have been stopped in the normal manner. A second purpose of the pushbutton is to stop the machine under operational emergency conditions. Pushing this button will provide electrical and immediate mechanical braking simultaneously. Therefore, this button should only be used if the operator intends the harshest braking of all motions. If the machine is in motion, power will remain on the motions in order to provide electrical braking for a few seconds. If the machine is in motion or stopped, this button will power the DC bus to approximately zero voltage quickly after the time delay.

PRESSING THIS BUTTON WHEN ANY DRIVE IS IN MOTION MAY RESULT IN COMPONENT DAMAGE. A second pushbutton that also provides the functions as described above is located in the remote start console and is labeled “machine stop.”

Main Power Off Pushbutton The main power off pushbutton is located on the right operator’s console. It is used only to immediately remove power from the drives in case of an electrical emergency involving component failure or fire.

PUSHING THE “POWER OFF” PUSHBUTTON WHILE IN MOTION WILL IMMEDIATELY SET THE MECHANICAL BRAKES AND REMOVE INCOMING HIGH VOLTAGE FROM THE DRIVES. THIS ACTION MAY RESULT IN COMPONENT DAMAGE. It will also result in the inability to power the DC bus voltage down to a low value. This voltage will decay slowly, taking several minutes.

OM11094-EN

7295 Electric Rope Shovel

59 July 2012

Operators Manual BI010535

Earth Continuity Lockout Pushbutton The earth continuity lockout pushbutton is used to trip the breaker that supplies power to the machine.

When the machine is operating, this pushbutton should be used to shutdown the machine only when removal of power to the machine is required.

Telephone A telephone is located at the rear of the right control console. This telephone is connected to other phone stations throughout the machine.

60 July 2012

7295 Electric Rope Shovel

OM11094-EN

Operators Manual BI010535

Operator’s Seat

Operator’s Seat - Front View

The operator’s seat has been selected to provide a maximum of operator comfort along with easy control access for increased productivity. The seat has numerous adjustments allowing it to be tailored to meet the individual needs of each operator.

Weight Adjustment The seat should be adjusted for the operator’s weight by pulling the actuator lever of the automatic weight and height adjuster while the operator is sitting in the seat and the machine is stationary.

OM11094-EN

7295 Electric Rope Shovel

61 July 2012

Operators Manual BI010535

Height Adjustment The seat height is adjusted pneumatically by pulling or pressing the adjustment lever as required to obtain the position required. DO NOT operate the compressor unit for more that 1 minute continuously.

Seat Cushion Angle Adjustment The angle of the seat cushion can be adjusted individually from the back. Lift the handle and exert pressure in the desired direction while seated. Release handle once the required position is achieved.

Seat Depth Adjustment The depth of the seat pan can be individually adjusted. Lift the handle and slide the seat pan forward or backwards to position. Release the handle when the desired position is obtained.

Armrest Adjustment The armrests can be adjusted to fit the individual needs of each operator or folded up and placed out of the way.

To adjust the armrest height loosen the manual friction knobs on the outboard side of the armrest allowing the armrests to pivot. Move the armrest to any desired position within its range and retighten when desired.

To raise the arm rests; lift at front and stow vertically.

Headrest Adjustment The headrest can easily be adjusted by lifting, or tilting, headrest to the desired position.

Lumbar Support The curvature of the backrest can be adjusted pneumatically by pressing the switches on the lower left rear of the backrest.

Backrest Adjustment The backrest is adjusted by lifting the lever and then releasing once the desired position is obtained.

62 July 2012

7295 Electric Rope Shovel

OM11094-EN

Operators Manual BI010535

Operator’s Display A PC based Operator’s Display is used to provide the operator with an interface to the machine and its functional areas. From this informational display the operator can make inputs that affect machine operation, monitor systems and make system adjustments. Through this display terminal the operator will receive pertinent fault data to identify potential problems and prevent machine damage.

Operator’s Display Panel

The display panel is mounted on an arm assembly protruding from a pedestal on the right side of the operator. The arm allows individual operators to locate the screen in any desired position. The monitor screen can be rotated along the horizontal and vertical axes.

OM11094-EN

7295 Electric Rope Shovel

63 July 2012

Operators Manual BI010535

Display Area And Indicators The display area of the monitor screen is the large area in the center of the screen. This area is “touch sensitive.” All information will be displayed on this area in either a text format or in the form of visual icons. The buttons and icons that appear on the screen will respond to touching the screen in the appropriate area of the icon.

These icons and buttons will react by activating the screen, switch activation or display information relevant to the icon.

All the machine controls can be found on the Operator’s Display Panel touch sensitive screen or the left and right Control Consoles of the operator’s seat.

64 July 2012

7295 Electric Rope Shovel

OM11094-EN

Operators Manual BI010535

Display Screens The Title Screen display appears when the machine is initially started.

The information provided in the central area of the screen is machine specific.

Language Screen

This screen allows the language used on the screens to be reset.

OM11094-EN

7295 Electric Rope Shovel

65 July 2012

Operators Manual BI010535

Icon Screen

This screen displays the icons used throughout all the screens in the system.

66 July 2012

7295 Electric Rope Shovel

OM11094-EN

Operators Manual BI010535

Active Alarm

The Active Alarm screen will provide a list of all active alarms and faults that have been initiated on the machine and have not been RESET. Once an alarm or fault has been sensed, these messages will remain visible and WILL NOT be removed from this screen until it is RESET. When a new alarm occurs, it shows up in a separate window on the top of any screen. It is cleared when there are no active alarms, the user goes to one of the other alarm screens, or the user presses the X next to the line.

NOTE: It is important to remember that messages will appear in this screen that are no longer active alarm messages. All messages will appear since the time of the last reset.

OM11094-EN

7295 Electric Rope Shovel

67 July 2012

Operators Manual BI010535

Alarms Help

The Alarms Help screen can be reached from any of the alarm message screens at any time. This screen will provide clarifying information related to the alarm system on your machine.

68 July 2012

7295 Electric Rope Shovel

OM11094-EN

Operators Manual BI010535

Rope Reeving/Pintle Tightening

The Rope Reeving/Pintle tightening screen is selected in order to make adjustments to the center pintle or change any of the main machine wire ropes. This screen will become active in the pintle tightening mode. If rope reeving is the desired intent, a selection must be made at the buttons in the lower left of the display area.

NOTE: Before switching between different modes of operation the Disable Selected Mode button should be pressed.

Switches for the activation/release of the hoist, crowd and swing brakes are provided, along with condition indicators displayed below the brake switches. This screen assists in the correct wrapping of the ropes on drums and allows full control of drum movements.

OM11094-EN

7295 Electric Rope Shovel

69 July 2012

Operators Manual BI010535

Rope Reeving/Pintle Tightening Help

This screen will provide clarifying information on the reeving of ropes and pintle tightening.

70 July 2012

7295 Electric Rope Shovel

OM11094-EN

Operators Manual BI010535

Calibration Limits

This Calibration screen is used to set the various limits required to control the movements of the machine. On this screen can be found switches for the hoist, crowd and swing brakes along with status indicators for each.

OM11094-EN

7295 Electric Rope Shovel

71 July 2012

Operators Manual BI010535

Limit Calibration Help

This screen will provide clarifying information on the calibration process.

72 July 2012

7295 Electric Rope Shovel

OM11094-EN

Operators Manual BI010535

Fault Counters/Operating Hours

The Fault Counter/Operating Hours screen provides the operator with information on the number of faults that have occurred since last RESET. It also provides the total operating hours.

OM11094-EN

7295 Electric Rope Shovel

73 July 2012

Operators Manual BI010535

PLC Menu Screen

This screen will activate further screens which are used to monitor various racks within the PLC cabinets.

PLC Main Screen 74 July 2012

7295 Electric Rope Shovel

OM11094-EN

Operators Manual BI010535

Operator’s Screen

The Operator’s Screen is the primary operational information tool to be visible to the machine operator during daily use of this machine. The controls available on this screen will provide the operator with the information needed to view “at a glance” the status of items required for digging and make changes in control settings.

OM11094-EN

7295 Electric Rope Shovel

75 July 2012

Operators Manual BI010535

Auxiliary Controls

Remote Start Console The remote start panel contains the following switches and indicator lights used to initially start the machine.

Phase Sequence Light This green indicator light, when lit, indicates that incoming power sequence is correct. If the light is OFF, have electrical maintenance change the trail cable phase sequence.

76 July 2012

7295 Electric Rope Shovel

OM11094-EN

Operators Manual BI010535

Drive Cabinets Temperature Light This green indicator light, when lit, indicates that the drive electronic cabinets are at the correct operating temperature. Too low or too high cabinet temperatures will not allow the machine to start.

PLC Power On Light This green indicator light, when lit, indicates that PLC and drive control power is on.

System Ready Light This green indicator light, when lit, indicates the system is ready to start. When the system run pushbutton is pressed and the system successfully started, this light will go out.

Auxiliary Ground Fault Light This green indicator light, when lit, indicates that no auxiliary power ground fault exists. If the light is OFF, alert an electrician as soon as possible.

Incomplete Sequence Light This red indicator light, when lit, indicates the automatic start-up sequence did not complete in a preset time period. Have an electrician troubleshoot the sequence. If this indicator does not light up, the start-up sequence is progressing properly and machine start-up can continue.

System Run Pushbutton This pushbutton will energize the drive system when pressed if the system ready light is on.

Air Compressor Start/Stop Pushbuttons The air compressor start and stop pushbuttons are used to control the auxiliary air compressor.

The stop pushbutton is only used for complete machine shutdown or when maintenance is being performed on the air compressor.

OM11094-EN

7295 Electric Rope Shovel

77 July 2012

Operators Manual BI010535

House Light Circuit Breakers

The house light circuit breakers are located on the right side wall of the machinery house next to the remote start console. A main light circuit breaker is located on the auxiliary control cabinet. The breakers protect the lights from over-current loads.

Lighting Transfer Switch

The lighting transfer switch is located on the right side wall of the machinery house near the lighting control center. This switch is used to transfer power for lighting from on machine source to off machine source.

78 July 2012

7295 Electric Rope Shovel

OM11094-EN

Operators Manual BI010535

Lubrication Control Panel The top row on this panel consists of a group of indicating lights. A red light indicating that the system has a fault and a green light indicating that power for the system is provided for each independent lubricating system (A, B & C). Isolating switches are used to provide power to each system and a means of isolating each system from electrical power. They are also used to reset lubrication faults. These switches are normally on. Manual lube buttons are also provided.

OM11094-EN

7295 Electric Rope Shovel

79 July 2012

Operators Manual BI010535

Windshield Wipers There are two electrically operated windshield wipers on the front window of the cab: one for the lower portion of the window and one for the upper portion of the window.

Check the wiper blades to make sure they swing freely across the window without contacting the window frame. Reposition the pantograph arm on the wiper motor shaft if necessary to prevent contact with the window frame.

Frequently check the condition of the wiper blades and replace if damaged.

Windshield Washer An optional electric operated windshield washer unit supplies a cleaning agent to the windshield through spray nozzles when activated. When operating in warm climates, water may be used as the agent. In areas where freezing temperatures are encountered, a suitable commercial windshield washer solvent with anti-freezing characteristics is recommended.

80 July 2012

7295 Electric Rope Shovel

OM11094-EN

Operators Manual BI010535

Pre-start Checks Before starting, inspect the machine to ensure it is ready to be put into operation. Failure to make such a routine check could result in unnecessary downtime. For example: an undetected oil leak could result in a dry gearcase, eventually leading to excessive gear wear or destruction, seized bearings or other mechanical problems. Broken strands in the hoist ropes, crowd rope, retract rope or structural strands could, if undetected, result in serious injury or damage to the machine or haulage unit. A few minutes spent inspecting the machine often results in considerable savings in time and machine efficiency.

Walkaround Ground Level Inspection Check the following areas daily during a general walkaround inspection: 1.

Check the areas under and around the crawlers for signs of oil leaks. If single droplets are noticed, leakage is minimal. Determine the point of leakage and make a note of it on the log sheet. If pooling of oil is noticed, determine the source and take corrective action immediately. Determine if loose hardware, a defective gasket, a combination of both, or a similar problem is responsible. Tighten hardware or replace defective gaskets.

2.

Inspect the crawler belts for missing links or lock pins, excessive belt sag, cracked shoes or other deterioration. Check the oil level in the propel planetary gearcase. Add oil as required.

3.

Check the swing rack and pinion guards for rocks, dirt and other debris that will interfere with the operation of the machine. Inspect the swing rack gear and rollers for the proper lubricant film.

HIGH VOLTAGE! THE MACHINE TRAIL CABLE CARRIES A LETHAL VOLTAGE. Handle the cable in an approved manner with appropriate rubber gloves and insulated hooks or tongs.

4.

Visually inspect the trail cable for cuts, abrasions and other damage.

5.

Visually inspect exterior of machinery house for damage or evidence of internal leakage.

6.

Inspect the dipper trip mechanism, rope, latch bar and associated hardware for damage, adjustment and wear.

7.

Inspect the dipper door, hardware and bumpers for damage and excessive wear.

8.

Inspect fulcrum attachment points, take up cylinders and spacers, and dipper handle for damage, excessive wear and evidence of adequate lubrication.

9.

Inspect boom bumper for security and damage.

10.

Inspect the dipper and tooth adapters for tightness and excessive wear.

OM11094-EN

7295 Electric Rope Shovel

81 July 2012

Operators Manual BI010535

11.

Inspect padlocks for damage, wear and evidence of adequate lubrication.

12.

Check both the running ropes and the boom structural strands for broken strands and loose sockets.

On-board Inspection Check the following areas daily on board the machine: 1.

Visually inspect the swing, crowd and hoist gearcases for oil levels and leaks. Repair or service as required.

2.

Visually inspect all machinery for loose bolts, nuts, clamps or unusual deterioration.

Repair as required.

3.

Visually inspect the open gears of the swing, crowd and hoist machinery for proper lubricant film and evidence of adequate lubrication from the automatic lubricant dispensing system.

4.

Visually inspect hoist and crowd ropes for wear, lubrication and evidence of birdcaging near the drum attachment beckets.

5.

Check the oil level in the air compressor. Add oil if required.

6.

Check lubricant supply level in the air system lubricator and lube system lubricators.

7.

Inspect the automatic lubrication central pumping stations for any signs of malfunctioning.

Check the lubricant supply and refill tanks if required.

8.

Visually inspect swing, crowd and hoist brake assemblies for damage, wear and evidence of an overheated condition.

9.

Check the operator’s cab for cleanliness and visual condition of controls and location of special equipment that may be required by the mine site. Check all operating controls for freedom of movement. Controls should move freely without binding.

10.

Clean windows of operator’s cab.

11.

Inspect all walkways and stairways to ensure there are no obstructions or fluids creating a safety hazard.

12.

Ensure ladder(s), steps and/or man basket are raised and properly stowed.

82 July 2012

7295 Electric Rope Shovel

OM11094-EN

Operators Manual BI010535

Machine Start-up, Operation And Shutdown Start-up Whether starting the machine for the first time, or starting after the machine has been in service for some time, the procedures are essentially the same.

1.

Perform all pre-start checks listed in PRE-START CHECKS in this section of the manual.

2.

Raise the boarding stair, making sure it is secured in the raised position. The limit switch at the top of the stair will not close and the controls will not energize if the stair is not in the fully-raised position.

Start-Up Control Locations

3.

In the operator’s cab check that all brake switches are in the SET position and that the joysticks are in the neutral position. Then go to the electrical room at the rear of the machinery house.

OM11094-EN

7295 Electric Rope Shovel

83 July 2012

Operators Manual BI010535

4.

At the AC control cabinet verify that the uninterruptable breaker is in the ON position. At the motor control cabinet, verify that all breakers are in the ON position.

5.

At the remote starting console in the machinery house, use the following sequence to start the machine: a.

Verify that the green AUXILIARY GROUND FAULT light is lit.

IF THE AUXILIARY GROUND FAULT LIGHT IS OFF, ALERT AN ELECTRICIAN AS SOON AS POSSIBLE. The machine may be operated with one fault but a second fault could cause damage to the machine and/or become a safety hazard. The fault should be cleared as soon as possible. b.

Verify that the green PHASE SEQUENCE light is lit. This indicates that the incoming power sequence is correct. If not, the light will be out and the machine will not start.

Electrical maintenance personnel must correct the problem.

NOTE: This PHASE SEQUENCE light also indicates auxiliary power phase unbalance, phase loss or under-voltage. Any of these faults occurring while the machine is running will produce an alarm. In the event of such an alarm an electrician should be notified, however the machine may be operated. c.

Verify that the PLC and drive cabinets’ green temperature lights are lit. If the cabinet temperature is too low or too high, the machine cannot be started.

d.

Press the UNINTERRUPTABLE POWER SUPPLY on pushbutton. A second start pushbutton is located on the UPS control cabinet.

e.

Verify that the green PLC POWER ON light is lit. This light should be on about 20 seconds after the UPS motor is started.

f.

Turn the AIR COMPRESSOR RUN switch to the run position or press the start pushbutton.

g.

Verify that the green SYSTEM READY light is lit.

h.

Press the SYSTEM RUN pushbutton. When this button is pressed, the system ready light will go out and the drive system will automatically power up.

i.

Verify that the red INCOMPLETE SEQUENCE light is out. If lit, call the electrician to troubleshoot the sequence.

6.

In the operator’s cab, verify that the air pressure displayed on the operator’s display is correct. The machine cannot be operated until the air pressure is at the specified rating.

7.

Verify that the brake switches are in the set position, the joysticks are in the neutral position and the air pressure is at the correct pressure. Sound the signal horn and be sure all personnel are clear of machine.

84 July 2012

7295 Electric Rope Shovel

OM11094-EN

Operators Manual BI010535

8.

Turn the propel transfer switch to the DIG position. When the Operator Display lights indicate that the process is complete, press the control reset pushbutton to activate the controls.

9.

Turn the hoist, crowd, swing and propel brake switches to their RELEASED position.

10.

Briefly actuate swing, crowd, hoist and propel controls to make sure each motion is operational.

Restarting After An Electrical Fault To restart the machine after the electrical control system has gone into a fault condition, proceed as follows: NOTE: Before any or all motions can be reset, the following conditions must be met: a.

No operator’s monitor special screens should be activated.

b.

For hoist/propel motion the hoist/propel transfer switch is in the position called for by the operator’s mode selector switch.

c.

The joystick for the motion being reset must be in the neutral position.

d.

The motion mechanical brake selector switch must be in the released position.

1.

For hoist or crowd travel limit faults, the motion will first slow down and then will stop, but the controls will remain active. Reversing the joystick will remove the fault and allow continued operation.

2.

For a boom jacking fault, the motion will stop but the controls will remain active. Reversing the left joystick will remove the fault and allow continued operation.

3.

If the boarding ladder is pulled down while the machine is in operation, an alarm message will be sent to the operator and swing and propel motions will be shut down. The hoist and crowd motions will remain active.

Once the ladder is back in position, the motions may be restarted by pressing the control reset pushbutton.

4.

For most other faults, the machine will be shut down and the brakes set. In these situations, the controls cannot be reset until the fault has been corrected by an electrician.

OM11094-EN

7295 Electric Rope Shovel

85 July 2012

Operators Manual BI010535

Operation Efficient operation is essentially the result of understanding and applying the basic techniques related to each machine motion, to achieve fast, smooth and safe load cycles. The interrelated coordination of the hoist, swing and crowd motions results in efficient machine operation.

Each motion is described in the following paragraphs. The operator should thoroughly learn each motion, its purpose and how this knowledge can be applied in becoming a better operator.

When learning to handle the operator controls, be sure that all personnel are clear of the machine and that there is ample clearance with no danger spots around the machine, such as culverts, ditches, embankments and that the machine is not too close to the digging face or overhanging ledge and large rocks.

Use the Operator Display panel, in the operator’s cab, to assist in the operation of the machine.

The monitor allows a large number of messages to be sent to the operator from all portions of the control system. These messages fit into four basic categories: 1.

Normal routine operational messages.

2.

Alarm only.

3.

Delayed shutdown messages.

4.

Immediate faults and shutdowns.

This monitor also allows the setting of certain operating parameters for the machine. Refer to OPERATOR’S DISPLAY in this section of the manual for detailed descriptions of the Operator Display monitor screens and how they relate to the proper operation of the machine.

86 July 2012

7295 Electric Rope Shovel

OM11094-EN

Operators Manual BI010535

Machinery Motions Hoist Motion In standard configuration, Hoist motion is controlled by the operator’s right joystick. Set the propel transfer switch in the DIG mode. The crawlers should be positioned so that the digging is done over the front of the crawlers. Move the joystick between hoist and lower until a “feel” is developed for the height, depth range and speed at which the dipper moves. Practice the hoist function until movement can be stopped smoothly.

This joystick also controls the swing motion through left and right motions.

NOTE:

The following represents the standard configuration.

OM11094-EN

7295 Electric Rope Shovel

87 July 2012

Operators Manual BI010535

Crowd Motion In standard configuration, Crowd motion is controlled by the operator’s left joystick. Move the joystick to crowd and retract the dipper handle until a “feel” is developed for the limits and speed of the motion.

This joystick also controls the signal horn and dipper trip.

NOTE:

The following represents the standard configuration.

Practice the crowd and retract functions until the movement can be stopped smoothly. Combine the crowd and hoist functions and practice until smooth coordinated motions and subsequent machine effectiveness are achieved.

88 July 2012

7295 Electric Rope Shovel

OM11094-EN

Operators Manual BI010535

Propel Motion Propel motion is controlled by placing the propel transfer switch in the propel mode and actuating the left or right joystick. To propel in a straight forward direction, push forward on both the left and right joysticks at the same time. The speed is increased as the levers are displaced farther from neutral. To propel straight in reverse, pull equally both joysticks to the rear.

NOTE: The control stop pushbutton must be pressed before the propel transfer switch can be activated.

THE HOIST BRAKE MUST BE SET WHENEVER IN THE PROPEL MODE.

Propel - Straight Forward/Reverse

OM11094-EN

7295 Electric Rope Shovel

89 July 2012

Operators Manual BI010535

Swing Motion In standard configuration, Swing motion is controlled by the operator’s right joystick. To swing in either direction, move the joystick lever in the direction of swing. Practice swinging in each direction until a “feel” is developed for start-up and stopping.

NOTE: The joy stick also controls the hoisting and lowering of the dipper through forward and backward motions.

Each motion - hoist or swing - is fully operational throughout the complete movement of the other motion.

NOTE: When this joystick is used for propelling the machine, the hoist and swing motions are electrically locked out.

NOTE: The following represents the standard configuration.

90 July 2012

7295 Electric Rope Shovel

OM11094-EN

Operators Manual BI010535

Proper Swing Motion Proper swing motion means smooth control and an efficient swing cycle. The swing motion is begun toward the haulage unit when the dipper is filled and is clear of the bank.

EXTENSIVE DAMAGE TO THE DIPPER HANDLE AND DIPPER CAN OCCUR IF THE MACHINE IS ROTATED BEFORE THE DIPPER CLEARS THE BANK. The swing motion begins with acceleration to an optimum point at which the excavator is brought to a stop over the haulage unit. Maximum efficiency and minimum swing machinery wear are direct results of mastering the swing motion.

NOTE: Improper swing motion results in erratic control and an inefficient swing cycle.

THE DIPPER SHOULD NEVER BE POSITIONED OVER PERSONNEL, TRAIL CABLES, RELATED ELECTRICAL EQUIPMENT OR OTHER EQUIPMENT. When the dipper is loaded, accidental tripping of the dipper door could result in death or serious injury to personnel and extensive damage to equipment. Empty dippers may contain small fragments of material that can be extremely dangerous when dropped from a considerable height. On long moves open the door on an empty dipper and lower the dipper to a point that permits moving without striking the ground.

OM11094-EN

7295 Electric Rope Shovel

91 July 2012

Operators Manual BI010535

Time is required to accelerate any motion from zero to working speed and also to decelerate from working speed back to zero. THE TIME EXPENDED FOR ACCELERATING AND DECELERATING THE SWING REPRESENTS THE MAJOR PART OF THE ENTIRE DIG CYCLE. Therefore, the swing arcs must be kept to a minimum to obtain maximum operating efficiency. As an example: assuming that a 90° swing results in 100 percent of the maximum output, increasing the swing arc to 180° reduces output to 70 percent, while decreasing the swing arc to 45° increased the output to 126 percent. Therefore, a swing arc of 90° or less should usually be used.

Haul units should be positioned so their center line is approximately under or not more than slightly outside the swing path of the boom point. This substantially reduces the amount of dipper maneuvering required of the operator when positioning the dipper for dumping. Positioning of the haulage unit inside or outside the boom point makes it necessary to retract or crowd the dipper handle and dipper, which breaks the operator’s natural rhythm.

A clean, level pit floor must be maintained. A good operator will always clean the floor before moving into the bank. A clean and level floor grade is a requisite to safe and stable machine operation and reduces damage to crawler links and related components.

“SWEEPING” SHOULD NEVER BE ATTEMPTED WITH THE MACHINE. Sweeping consists of lowering the dipper to the ground and using the swing motion of the machine to move the dipper from side-to-side and “sweep” the pit floor. THE DIPPER, DIPPER HANDLE AND BOOM STRUCTURES CAN BE DAMAGED BY SWEEPING. A bulldozer or loader should be used to help the machine operator maintain a clean pit floor in conjunction with the shovel.

92 July 2012

7295 Electric Rope Shovel

OM11094-EN

Operators Manual BI010535

Steering

To make a gradual forward right turn, move the LEFT joystick (crowd) forward and leave the right joystick (hoist) in neutral.

OM11094-EN

7295 Electric Rope Shovel

93 July 2012

Operators Manual BI010535

To make a gradual forward left turn, move the RIGHT joystick (hoist) forward and leave the left joystick (crowd) in neutral.

Whenever possible, gradual turns should be made in short increments of 15° to 20° maximum.

Propel straight for a short distance (usually 1/2 the length of the crawler belts) to clear the crawler belts of stone and other debris; then make another 15° to 20° turn. Continue until the turn is completed.

NOTE: When steering in soft material such as sand, clay, etc., increments of less than 15° to 20° should be used to minimize material build up on the crawler belt roller path.

94 July 2012

7295 Electric Rope Shovel

OM11094-EN

Operators Manual BI010535

Counter-rotation Turns

Although possible, a single sharp turn should be avoided to minimize material build up on the crawler belt roller path. This results in high loading of the crawler belt and associated propel components.

To make a sharp right turn, move the LEFT joystick forward and pull the RIGHT joystick to the rear.

To make a sharp left turn, move the RIGHT joystick forward and pull the LEFT joystick to the rear.

When using the counter-rotation method for turning, have a helper ensure that the trail cable does not get fouled and/or torn from the machine.

NOTE: The ability of the machine to turn sharply is dependent on the surface on which the machine is setting. A soft surface will cause the crawlers to dig-in and machine to bogdown.

The propel brakes are released when either joystick is moved from neutral. The propel brakes are set when both joysticks are returned to neutral.

OM11094-EN

7295 Electric Rope Shovel

95 July 2012

Operators Manual BI010535

When moving the machine in a straight line, propel forward, which is in the direction of the take-up axle to reduce strain on the crawler belts and propel mechanism. When not possible and propelling to the rear, make sure the trail cable is clear of the machine and follow the signals given by the helper. The machine should be rotated in a position to allow the operator to face the direction of travel.

NOTE: Turning when propelling to the rear requires that the master control be positioned in a direction opposite the actual direction in which the turn takes place.

The machine should be moved close to the bank in short and frequent moves to maintain digging efficiency. Movement should occur between the loadings of haul units.

96 July 2012

7295 Electric Rope Shovel

OM11094-EN

Operators Manual BI010535

Positioning The Machine There are two basic methods for positioning the machine at the working face of the bank: the “back-up method” and the “drive-by method”. Both methods are acceptable and effective.

Back-up Method When using the back-up method, position the machine at the bank with the front of the machine facing the digging face. The haul units are spotted on both sides of the machine. The bank can be excavated until a 180° circular area of material has been removed from the bank. Once the material is removed, a 90° or greater swing will be required in order to load the haul units, requiring the machine to be moved.

To reposition the machine, propel to the rear, away from the bank, at an approximate 45° angle to the bank. When the machine is centered in-line with the untouched edge of the previous excavation, propel straight toward the bank and position the machine for further digging.

The back-up method will minimize the swing arc and reduce moving time, produce less bank toe area clean up and simplify handling of the trail cable, cable standard and trail cable boat.

OM11094-EN

7295 Electric Rope Shovel

97 July 2012

Operators Manual BI010535

Drive-by Method NOTE: If mine conditions or equipment prevent the use of the following procedures, use the “Back-up Method” instead.

Position the machine crawlers parallel to the bank with the outer set of crawler tracks directly in line with the bank toe.

The haul units must approach the machine from the front, making a turn away from the machine as the unit’s front wheel approaches the outside crawler. Haul units then stop in a position to allow backing toward the point of the bank for loading.

During the load cycle, swing arc is to one side only and should not exceed 90°. The cycle time from one full haul unit to the next empty unit should not exceed the cycle time between successive dipper loads to each unit.

During the load cycle, the swing arc should not exceed 90°. The time between finishing one truck to the first digging cycle of the next should not exceed that of any cycle during a load.

98 July 2012

7295 Electric Rope Shovel

OM11094-EN

Operators Manual BI010535

Start Of The Dig Cycle

Force the Dipper Lip into the Bank

The crowd motion forces the dipper lip into the bank at the start of the digging cycle. It is the crowd thrust which enables the dipper lip and front opening to get into a column of material of sufficient cross section to fill the dipper rapidly.

There is a direct relationship between crowd depth of bank penetration and the distance the dipper must rise in the bank to fill the dipper. The deeper the “bite” the quicker the dipper will be filled, providing the hoist force is sufficient to cut the column of material. Do not attempt to lift the entire bank with each pass. As soon as the dipper is full, retract it from the bank and swing the machine to fill the truck.

Crowd penetration should be rapid just at the arc of entry and rise as the dipper enters the bank.

This will permit as much digging as possible near the base of the bank. This is of particular advantage when digging loose or blasted material. The greater the hoist force and crowd thrust, the faster the dipper filling time of the dig cycle. The crowd thrust should be maintained to hold the dipper in the bank while it is being hoisted. An added benefit of proper crowd thrust and hoist force is that the opposing vertical resistance of the bank material tends to have a “ramming” effect in the dipper front opening, minimizing voids and producing larger dipper loads.

OM11094-EN

7295 Electric Rope Shovel

99 July 2012

Operators Manual BI010535

It is important that the full cutting surface of the dipper contact the bank on each pass. A full face cut combined with deep bank penetration will result in a full dipper for the least amount of hoist. A partial cut, even with deep bank penetration, requires a greater rise and tends to leave voids in the dipper, requiring additional passes to fill the haulage unit.

Shallow bank penetration of the arc of entry and rise is ineffective and inefficient. A shaving cut dribbles material into the dipper resulting in voids and making additional passes necessary while accelerating dipper lip wear.

100 July 2012

7295 Electric Rope Shovel

OM11094-EN

Operators Manual BI010535

NOTE: A Deeper Bite = Quicker Fill Times Digging should take place under the boom point for maximum shovel effectiveness. If necessary, the machine should be moved closer to the bank face, rather than extending the dipper handle.

Reaching for material results in a partially filled dipper and excessive crowd and retract time. Use caution not to damage the boom point sheaves when operating close to the high wall.

Variations on Dipper Penetration

OM11094-EN

7295 Electric Rope Shovel

101 July 2012

Operators Manual BI010535

Dig with the Dipper Beneath the Boom Point

Overcrowding with the dipper lowered can result in lifting the boom. This jacking action can result in damaged components. Overcrowding the dipper in the bank slows up the dipper loading process, thereby reducing machine efficiency.

102 July 2012

7295 Electric Rope Shovel

OM11094-EN

Operators Manual BI010535

Engaging The Bank

Make Effective Use of the Hoist Effort

To make maximum use of the hoist rope pull, the dipper rise should be as close to vertical as possible. The dipper should enter the bank approximately under and behind the boom point. The actual cut should start a few degrees behind an imaginary vertical line from the front of the boom point sheaves. Proper bank engagement results in maximum hoisting force in line with the cut.

When the dipper is too far forward, bank penetration will be minimal and the hoist and crowd forces will oppose each other rather than working together.

Hoist Force Opposes Crowd Force

Dipper capacity rating is the struck measure cubic yard capacity. When digging, a load greater or less than the rated capacity may be obtained, depending on the type of material. An efficient operation can be measured by the number of dipper loads required to load a haulage unit. When the dipper capacity is efficiently sized to the truck capacity, not less than three or more than five dippers full should be required to load a unit. Other factors such as improper sizing of haulage units to dipper, improper material fragmentation, etc., also must be considered.

OM11094-EN

7295 Electric Rope Shovel

103 July 2012

Operators Manual BI010535

In all types of digging the skilled operator must carefully control the desired depth of cut and control the hoist power requirements. Often, digging situations are encountered which require hoist and crowd motions to maneuver around oversize or lodged obstructions in the bank, rather than attempting to lift the entire bank.

MAINTAIN A DIGGING FACE WHICH AVOIDS ANY MAJOR SLIDES WHICH COULD CAUSE AN ACCIDENT. Examine the digging face for large boulders, large rocks, or frozen material which could slide and cause an accident. Avoid overhanging material.

Do not repeatedly stall the dipper in the bank, nor maintain a stall condition. The life expectancy of the hoist machinery and hoist ropes is directly related to the operator’s skill in avoiding stalling.

Whenever stall conditions are encountered, back off on the hoist motion, retract the dipper, or do both. Avoid stall conditions at all times.

DO NOT SUSPEND A LOADED OR EMPTY DIPPER IN THE AIR WITH THE BRAKES SET FOR LONG TIME PERIODS. Lower the dipper to the ground if the machine is to be idle or unattended for any length of time. Failure to comply can result in personal injury or death of anyone beneath the dipper.

104 July 2012

7295 Electric Rope Shovel

OM11094-EN

Operators Manual BI010535

For most efficient production, the dipper should be loaded from the most remote point while waiting for a truck. When the truck is positioned, excavating should begin close to the haulage unit, progressively working away from the unit.

This technique saves time by allowing smooth, short dig cycles and eliminates excessive swing, crowd and retract motions.

OM11094-EN

7295 Electric Rope Shovel

105 July 2012

Operators Manual BI010535

Slope Limitations While it is strongly recommended that the machine dig on level ground for the greatest possible productivity and the longest component life, limited operation on slopes up to 8% is, however; acceptable with only minimal adverse effects.

NOTE: It is important to remember the difference between Slope Percent and Degrees!

Slope vs. Degrees

106 July 2012

7295 Electric Rope Shovel

OM11094-EN

Operators Manual BI010535

Rollover and Operation Limits

OM11094-EN

7295 Electric Rope Shovel

107 July 2012

Operators Manual BI010535

Excavated Material It is important that the operator not only know the controls but recognize other aspects of the mining operation. Chief among these is the type of material to be excavated. It plays a great part in the overall efficiency of the machine.

Materials can be roughly divided into four categories.

1.

EASY DIGGING - This category includes all loose, free-flowing materials, such as sand and gravel deposits, stock pile materials such as finely crushed stone, ore fines, coal fines and any other similar materials. The dipper will usually obtain a heaped load.

2.

MEDIUM DIGGING - This category includes only materials which can be excavated from their natural beds without blasting and which break up in bulk with some voids. Such material includes clay, dry earth, clay-gravel mixtures, gravel with some boulders, certain types of ores and coal. The dipper will usually obtain a full load, with filling augmented by the material’s natural tendency to break apart when it encounters the dipper lip and teeth.

3.

HARD DIGGING - Included in this category are materials that require blasting, resulting in good fragmentation, but leaving large chunks which develop voids. Limestone, gypsum shale, cemented gravel, wet earth, clay and certain types of ore and overburden all fall within this category. The dipper will average less than a full load because of the resistance of the material against flow and voids due to blocky material

4.

VERY HARD DIGGING - This category includes all materials that require heavy blasting and give irregular fragmentation. Taconite, granite, laminar shale, certain types of limestone and conglomerate overburden fall into this category. The dipper will average considerably less than a full load, because of the large chunks and interlocking action of the material which block fill.

108 July 2012

7295 Electric Rope Shovel

OM11094-EN

Operators Manual BI010535

Operation Checks During machine operation there are several things to consider relative to safe, efficient machine operation.

1.

Check the motors for unusual noise, loss of power or failure to respond to controls.

2.

Check hoist, crowd, swing and propel machinery for unusual sounds and overheating of bearings.

3.

Avoid slack hoist ropes which could allow the ropes to become crossed on the drum, or skip a groove.

4.

Check the air gauge frequently and investigate immediately if there is a drop in air pressure. Correct all air leaks.

5.

When propelling, check the engagement of the drive tumblers on the crawler belt links and adjust the belts to correct any improper alignment.

6.

When operating auxiliary functions, such as steering, note any tendency of the controls to jam or hang up. Check and correct any problems at the earliest opportunity.

OM11094-EN

7295 Electric Rope Shovel

109 July 2012

Operators Manual BI010535

Operating Hints The following hints are reminders of the do’s and don’ts related to excavator operation: •

Engage the bank properly.

•

Load with the successive pass technique.

•

Maintain a clean pit floor.

•

Use proper hoist control.

•

Make effective use of the hoist pull.

•

Use proper crowd control.

•

Force the dipper lip into the bank at the arc of entry.

•

Crowd the dipper into the bank for deep penetration.

•

Make full face cuts for faster loading cycles.

•

Dig under the boom point.

•

Make smooth, safe swing cycles.

•

Keep swing arcs within 90°.

•

“Spot” the haulage units properly.

•

Keep the working faces free of projections.

•

Propel forward whenever possible rather than backward.

•

Move up to the bank frequently.

•

Dig over the take-up axle end of the crawlers whenever possible.

•

Make gradual turns when propelling.

•

Do not suspend a loaded dipper for an extended time.

•

Do not operate too close to material.

•

Do not operate with missing dipper teeth.

•

Do not stall hoist or crowd motions.

•

Do not reach for material.

•

Do not reach for haulage units.

•

Do not overcrowd and jack the boom or machine.

•

Do not make partial face cuts.

•

Do not make shallow bank penetration.

•

Do not make erratic swings.

•

Do not swing until dipper is clear of the bank.

•

Do not swing loaded or unloaded dippers over personnel or equipment.

110 July 2012

7295 Electric Rope Shovel

OM11094-EN

Operators Manual BI010535

•

Do not “sweep” pit floor.

•

Do not make sharp turns when propelling.

•

Do not make long inefficient moves.

•

Do not exceed swing arc of 90°.

•

Do not spot haulage units inside or outside the boom point swing arc.

•

Maintain adequate clearance between digging face and point sheaves.

•

Do not allow the dipper to contact the crawler belts.

Stopping The Machine 1.

Return left and right joysticks to their center positions and set all brake switches.

2.

After all motions are stopped and brakes are set, press the CONTROL STOP pushbutton.

This action will remove power to the control units and set the brakes. The controls will become inoperative.

3.

To stop the machine completely and remove power from the drives, press the MACHINE STOP Pushbutton on the right operator’s console.

Machine Shutdown When shutting down the machine at the end of a shift proceed as follows: 1.

Park the machine on firm ground in a position where it cannot be damaged by a slide, falling rocks or flooding. In cold climates, be sure the crawler belts will not freeze into the ground.

2.

Place the dipper firmly on the ground.

3.

Make sure left and right joysticks are in their center positions.

4.

Make sure all brake switches are in their SET positions.

5.

Press the CONTROL STOP pushbutton. All primary controls should be de-energized.

6.

To de-energize the DC bus, press the MACHINE STOP pushbutton on the remote start console or the MACHINE STOP/EMERGENCY STOP pushbutton on the operator’s console.

7.

Place the air compressor switch on the remote start console in the STOP position.

8.

Close all windows in the cab and lock all cab doors.

OM11094-EN

7295 Electric Rope Shovel

111 July 2012

Operators Manual BI010535

General Estimated Component Weights

These are estimated weights only. Contact the manufacturer for the exact weight of components on your specific machine before rigging and lifting.

Quantity

Weight Each (U.S. Pounds)

Frame And Swing Rack Components Roller Frame Assembly Roller, Roller Frame Guard, Roller Circle Guard, Roller Circle Revolving Frame Center Pintle Support, Crowd Machinery Base, Crowd Motor Rail, Upper-Center Rail,Center-Upper Segment, Rail Rail, Upper End Rail, Upper End Pintle, Center Sleeve, Center Pintle Lock Nut, Lower, Center Pintle Thrust Washer, Center Pintle Lock Nut, Upper, Center Pintle Pin, Boom Foot Pin, A-Frame Swing Rack Assembly Swing Rack Rail, Lower Rail Segment Truck Frame Assembly Hub, Center Pintle Bushing, Center Pintle Cover, Bottom Plate Cover, Plate Cover, Manhole 112 July 2012

1 54 1 1 1 1 2 1 4 4 2 2 2 1 1 1 1 1 2 4 1 1 15 15 1 1 1 1 1 3

7295 Electric Rope Shovel

17,330 290 100 90 80,180 5,680 820 580 120 230 220 140 140 7,170 5,210 1,080 330 480 320 300 23,510 21,000 230 220 103,440 2,810 270 730 110 60 OM11094-EN

Operators Manual BI010535

Quantity

Weight Each (U.S. Pounds)

Propel Components Motor, Propel/Guards Assembly Propel Motor Propel Blower Brake, Propel Adapter, Propel Brake Coupling, Propel Guard, Propel Coupling Support, Propel Motor Duct Assembly, Propel Blower Inlet Guard

1 2 2 2 2 2 2 2 2 2

17,130 4,000 230 490 230 140 80 2,960 220 130

Crawler Components Crawler Assembly Crawler Assembly, RH Crawler Assembly, LH Crawler, Frame Weldment, RH Crawler, Frame Weldment, LH Flange, Mounting Retainer Roller, Load, Rear Roller, Load, Assembly Roller, Front Idler Sprocket, Crawler Shaft, Roller, Front Shaft, Roller, Rear Adjusting Block Assembly Shaft, Idler Shaft, Main Propel Bearing, Roller, Crawler Sprocket Rod, w/Torquenut Assembly Gearcase Assembly, Propel Cabinet, Lube, Crawler Belt, Crawler Link, Crawler, 72 Inch

1 1 1 1 1 2 2 2 16 2 2 16 2 4 2 2 2 40 2 2 2 96

217,630 93,990 93,990 57,910 57,910 2,680 190 2,230 1,440 3,480 4,980 410 530 460 1,060 3,180 340 80 12,600 330 68,950 1,370

OM11094-EN

7295 Electric Rope Shovel

113 July 2012

Operators Manual BI010535

Quantity

Weight Each (U.S. Pounds)

Operator Cab Components Operator Cab Assembly Operator Cab, FOPS Operator Cab Support Console, Operator Control Door & Frame Assembly Glass, Door Window, Front Assembly Base, Operator Seat Duct Assembly, Air Conditioner Air Conditioner Ducting, Air Conditioner

1 1 1 1 1 1 1 1 1 1 1

10,790 6,970 5,950 320 280 50 460 150 310 930 100

Collector Ring Components Housing, Collector Ring, Front Housing, Collector Ring, Rear Guard, Hose Support, Swivel Housing Air Swivel, 4-Line Ring, Collector Ring, Collector Ring, Collector Ring, Collector Ring, Collector Support, Shoe

1 1 1 1 1 1 1 1 1 1 2

140 140 90 710 150 130 100 80 60 150 60

Boom & Dipper Handle Components Boom Assembly, 59ft Hub, Shipper Shaft Foot, Boom Bushing, Tube Bumper Assembly, Boom Sheave, Boom Point Shaft, Boom Point Housing, Boom Point , RH Housing, Boom Point , RH Housing, Boom Point , LH Housing, Boom Point , LH

1 2 2 4 2 2 2 1 1 1 1

85,300 1,650 850 90 1,630 4,130 1,130 880 870 880 870

114 July 2012

7295 Electric Rope Shovel

OM11094-EN

Operators Manual BI010535

Quantity

Weight Each (U.S. Pounds)

Boom & Dipper Handle Components (cont.)

Bearing, Boom Point Shipper Shaft

2 1

280 4,500

Dipper Trip Components Base, Dipper Trip Guard, Dipper Trip Drum Drum, Dipper Trip Gear, Dipper Trip Support, Deflector Support, Dipper Trip Pad, Mounting, Dipper Trip, Rear Pad, Mounting, Dipper Trip, Front Motor, Dipper Trip Rope, Dipper Trip

1 1 1 1 1 1 1 1 1 1

750 70 100 160 100 200 100 130 700 80

Swing Machinery Retainer, Bearing, Vertical Swing Shaft Pinion, Vertical Swing, Induction Gear, Swing Bearing, Taper Roller Bearing, Roller Guard, Swing Pinion Retainer, Bearing, Intermediate Shaft Pinion, Shaft, 2nd Reduction Bearing, Taper, Roller Gearcase & Cover Cover, Swing Gearcase Gearcase, Swing Hub, Swing Gearcase Gear, Intermediate Swing Shaft Motor, Swing Blower, Swing Motor Adapter, Swing Blower Swing Brake Adapter, Swing Brake

2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 1 2 2

90 1,110 1,710 100 180 110 100 220 100 6,580 1,670 5,880 1,790 1,030 3,600 230 1,760 490 210

OM11094-EN

7295 Electric Rope Shovel

115 July 2012

Operators Manual BI010535

Quantity

Weight Each (U.S. Pounds)

Crowd Machinery Crowd Frame Motor, Crowd Blower, Crowd Motor Duct Assembly, Crowd Motor Blower Brake, Crowd Crowd Drum Coupling, Crowd Input Shaft Rope, Wire, Crowd & Retract Gear,1st Reduction, Crowd Pinion, Shaft, 1st Reduction Guard, Pinion, Crowd Machinery Guard, Gear - Crowd Guard, Gear - Crowd Pinion, 2nd Reduction Shaft, 1st Intermediate, Crowd Machinery Bearing, Roller Pinion, Shaft, 3rd Reduction Gear, 2nd Intermediate Bearing, Roller Bearing, Roller End Cap Bearing, Spherical Roller Gear, Crowd Drum Cap, Bearing - Crowd Pin, Crowd, Front Guard, Crowd Whole Split Cover, Crowd Gearcase Cover, Plate

116 July 2012

1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 2 4 1 1 1

7295 Electric Rope Shovel

14,800 3,500 200 270 490 12,670 1,690 70 1,380 170 130 90 200 110 1,260 60 1,920 1,300 120 60 80 110 3,990 500 70 90 1,400 100

OM11094-EN

Operators Manual BI010535

Quantity

Weight Each (U.S. Pounds)

Machinery House Components Machinery House Ballast Box Ballast Lube Room - Machinery House Lube Reservoir Lube Pump Heater, Lube Room Hoist, Lube Room Heater, Control Room Air Compressor Support, Auxiliary Winch Drum, Auxiliary Winch Rope, Wire Duct, Transition Bleed Duct Duct, Transition Duct, Cleanout Duct, Cleanout Filter, Air -15 Double Cell Filter, Air - 9 Double Cell Hood, Dual Fan Leg, Front, A-Frame Foot, A-Frame Pin, A-Frame Back Leg, A-Frame Platform Assembly, A-Frame Equalizer Link Rope Pendant

OM11094-EN

1 1 1 1 2 4 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 2 4 2 1 2 4

7295 Electric Rope Shovel

10,780 100,660 352,000 6,550 330 70 80 190 160 1,100 750 210 210 140 60 380 340 460 2,050 1,330 800 16,550 700 300 4,030 3,120 940 1,700

117 July 2012

Operators Manual BI010535

Quantity

Weight Each (U.S. Pounds)

Dipper Components Dipper Assembly, 25yd Pin, Dipper Pin, Dipper Dipper Body, Weldment Latch Keeper Dipper Door, Weldment Latch Mechanism Lever, Latch Latch Bar Snubber Assembly, RH Snubber Assembly, LH Frame, Padlock Link, Padlock, RH Link, Padlock, LH Sheave, Padlock Bushing, Manganese Bushing, Manganese Pin, Padlock Frame Pin, Padlock Frame Pin, Clad Pitch Brace w/Manganese Bushing Pin, Pitch Brace Dipper Shrouds & Teeth Assembly

118 July 2012

1 2 2 1 1 1 1 1 1 1 1 2 1 1 2 8 2 2 2 2 2 4 1

7295 Electric Rope Shovel

61,190 290 240 44,270 1,060 12,310 1,050 260 500 1,190 1,190 1,480 750 750 750 90 50 370 250 370 320 170 10,020

OM11094-EN

Operators Manual BI010535

Quantity

Weight Each (U.S. Pounds)

Hoist Components Cover, Bearing, Hoist Shaft & Pinion, Intermediate Bearing, Roller Bearing, Roller End, Plate Cover, Hoist Bearing, RH Pin, Bearing Housing Pin, Bearing Housing Retainer, Whole-Split Seal, Split Retainer, Hoist Drum, LH Retainer, Bearing, Hoist Drum Housing, Bearing, RH Housing, Bearing Spider, LH Gear, Hoist Drum Bearing, Roller Cover, Plate Cover, Gear, Front Cover, Gear, Lower Cover, Gear, Rear Cover, Gearcase Carrier, Intermediate Shaft & Pinion, RH Side Frame, Gearcase, LH Bolt, Rod Support, Drum, RH Guard, Hoist Coupling Drum, Hoist Brake, Hoist Hub, Horizontal Brake Adapter, Hoist Brake Motor, Hoist Blower, Hoist Motor Adapter Plate, Hoist Blower

OM11094-EN

1 1 1 1 1 1 1 3 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1

7295 Electric Rope Shovel

210 2,150 120 410 170 250 470 210 170 120 200 260 2,830 2,780 5,390 8,560 510 290 600 1,160 710 3,460 1,280 13,050 60 5,400 100 16,700 1,030 140 420 15,180 430 260

119 July 2012

Operators Manual BI010535

Quantity

Weight Each (U.S. Pounds)

Hoist Components (cont.)

Rope, Wire, Hoist Gear, Hoist, 1st Reduction Coupling, Gear, Motor Pinion, Shaft, 1st Reduction Spider, RH

1 2 1 1 1

2,650 5,950 430 520 3,200

Dipper Handle Components Dipper Handle Assembly Handle, Lower End Dipper Handle Support, Take-Up Spreader, Retract Retract Take-Up Nut, Take-Up Cylinder, Hydraulic Take-Up Guide, Take-Up Cylinder Guard Support Guard, Shim Sheave, Half-Fixed, Crowd Saddle Block Retainer Seal, Saddle Block Sheave, Crowd Bearing, Tapered Roller Bushing, Saddle Block Collar, Whole-Split Bushing, Liner, Saddle Block

1 1 1 1 1 1 1 2 1 1 1 1 1 4 2 2 2 2 2

44,170 40,000 34,570 1,300 2,030 3,020 1,180 110 460 130 150 3,960 15,600 120 2,600 350 100 120 1,290

120 July 2012

7295 Electric Rope Shovel

OM11094-EN

Operators Manual BI010535

Quantity

Weight Each (U.S. Pounds)

Electrical Components Skid, IGBT Drive Transformer, DPT Transformer, Auxiliary Power Switch, Disconnect, High Voltage Motor Control Center (MCC1) Fan, Intake, Front Fan, Intake, Rear Motor, Reeving Winch Transformer, CVT Transformer, DTT Transformer, LTT Duct, IGBT Skid Duct, IGBT Skid Fan, DPT Exhaust

OM11094-EN

1 1 1 1 1 1 1 1 1 1 1 1 1 1

7295 Electric Rope Shovel

18,000 11,500 2,750 1,800 1,500 1,190 820 610 300 240 240 110 170 70

121 July 2012

Operators Manual BI010535

122 July 2012

7295 Electric Rope Shovel

OM11094-EN

®

Amendments and alterations to this publication are not subject to notification. Caterpillar Global Mining LLC reserves all rights to this publication. Its content is protected by copyright laws.

No part of this publication may be reproduced or transferred in any way or form without the prior written approval of Caterpillar Global Mining LLC. Caterpillar Global Mining LLC declines any liability for direct or indirect consequences of printing errors. © 2012 Caterpillar Global Mining LLC. LatchFree™ and HydraCrowd™ © 2012 Bucyrus International, Inc.