Cab

OPERA TION

not start the engine in enclosed areas that not have adequate ventilation capable removing exhaust gases, they are harmful your health. Keep the operator ’s compartment free foreign objects, especially if not firmly secured. Never use the machine transport objects that are not properly secured. not transport passengers the machine. Study and familiarize yourself with the emergency exits that are alternatives the normal exiting procedures. For your personal safety , not climb f the machine when it is moving. Obey all hand signals, safety indications and signs. When moving the machine in reverse, always look where the machine is being moved. Be alert the position people near the machine. Should someone enter the work area, stop the machine. Maintain a safe distance from other machines obstacles ensure required visibility conditions. Give way loaded machines. Always keep a clear view the travel area work area. Keep cab windows clean and repaired. When pulling loads towing with a cable chain, start moving slowly prevent bumps. Keep a safe distance from what is being pulled towed. Check the towing components for defects issues before proceeding. A void kinking twisting chains cables. not use kinked chains cables. The concentration stresses caused this condition may induce failures in the kinked area. Always wear heavy gloves when handling chains cables. Chains and cables should securely anchored using suitable hooks and eyes. The anchor points should strong enough withstand the desired load. Keep people clear anchor points and cables chains. not pull tow unless the operator ’s compartments the machines involved are properly protected against a possible breakage the cable chain. Be alert soft ground conditions close recently excavated walls. The fill material and machine weight may cause the wall collapse under the machine. darkness, check the area operation carefully before moving in with the machine. Use all lights available. not move the machine into areas with low visibility . the engine speed drops, loses power stops, for any reason, under load idle, immediately report this issue the maintenance managers obtain proper instructions. not operate the machine until this condition is corrected. Regularly check all exhaust system components, exhaust fumes are toxic for the operator . Operators must know the performance the machine they are operating. When working slopes near sudden drop - in the terrain, pay attention not lose adherence. A void very soft ground, this may result in a rollover loss control the machine. noise level is very intense and exceeds (A) in the operator's ear for more than 8 hours, use approved ear protection in compliance with local regulations.

not operate the machine if you are extremely tired feeling ill sick. Be especially careful toward the end the work shift. there are removable counterweights, not operate the machine if they have been removed. When operating the machine, verify the height limits doors, arches, overhead cables and electrical lines, well width limits corridors, roads and narrow passages. is important obtain information about the load limits the ground and paving type the ramps where you are working. Beware fog, smoke dust that obscure visibility . Always inspect the work area identify potential risks such as: steep slopes, overhangs, terraces, trees, demolition, rubble, fires, ravines, rough terrain, drains, convex areas, excavations in traf fic areas, areas with many parked cars, populated service areas, fenced areas. such conditions, operate with extreme caution. Whenever possible, avoid passing over obstacles such as: very rough terrain, rocks, tree stumps, steps, drains, railroad tracks. it is necessary cross obstacles, with extreme caution and a right angle, if possible. Reduce speed, approach the obstacle slowly , pass slowly through the point balance and through the other side. Also use the attachment support, if necessary . To pas over deep trenches flooded ground, place the machine perpendicular the obstacle, drastically reduce the speed and start cross using aid the attachment if necessary , only after assessing if the ground conditions allow the safely crossing without risks. The slope crossed is limited factors such ground conditions, the load being handled, the machine type, speed and visibility . There is substitute for good judgement and experience when working sloped terrain. A void operating the attachment too close bank high wall, either above below the machine. T ake care with landslide from the edges the excavation and falling objects. Remember that such hazards may hidden bushes, brush and undergrowth. A void brush, logs and rocks. Never drive over them over any other surface irregularities that interrupt adherence traction with the ground, especially near steep slopes. Be alert avoid changes in adherence conditions that cause loss control. W ork with extreme care ice frozen ground and stepped slopes near drop fs. The word “levelling” generally refers work in virgin rough terrain, characterized the presence all the perils and risks listed above. We emphasize the danger represented in these conditions tree limbs (possibly falling the machine) and large roots (which may act a lever under the machine when uprooted and cause the machine become unstable and overturn). Position the machine according the loading and unloading areas that it can swing the left - hand side for loading and the operator has the best possible visibility . Never use the bucket attachment lift carry people. Never use the machine a work platform scaf folding. The machine must not used improperly . for works not