Case 721D Wheel Loaders Operator's Manual 6-35092NA - PDF DOWNLOAD

721D Wheel Loaders Operator's Manual Revision Date 09/2004

Bur 6-35092NA

!

THIS SAFETY ALERT SYMBOL INDICATES IMPORTANT SAFETY MESSAGES IN THIS MANUAL. WHEN YOU SEE THIS SYMBOL, CAREFULLY READ THE MESSAGE THAT FOLLOWS AND BE ALERT TO THE POSSIBI LITY OF DEATH OR SERIOUS INJURY. M171C

Safety Decals on this machine use the words Danger, Warning or Caution, which are defined as follows: ➏ DANGER: Indicates an immediate hazardous situation which, if not avoided, will result in deat h or serious injury. The color associated with Danger is RED. ➏ WARNING: Indicates a potentially hazardous situation which, if not avoided will result in serious injury. The color associated with Warning is ORANGE. ➏ CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in mino r or moderate injury. It may also be used to alert against unsafe practices. The color associated with Caution is YELLOW.

! WARNING IMPROPER OPERATION OF THIS MACHINE CAN CAUSE DEATH OR SERIOUS INJURY. BEFORE USING THIS MACHINE, MAKE CERTAIN THAT EVERY OPERATOR: ➏ Is instructed in safe and proper use of the machine. ➏ Reads and understands the Manual(s) pertaining to the machine. ➏ Reads and understands ALL Safety Decals on the machine. ➏ Clears the area of other persons. ➏ Learns and practices safe use of machine controls in a safe, clear area before operating this machine on a job site.

It is your responsibility to obse rve pertinent laws and regulations and follow Case Corporation instructions on machine operation and maintenance.

Copyright © 2004 CNH America LLC All Rights Reserved CASE is a registered tradmark of CNH America LLC.

Bur 6-35092NA September 2004

TO THE OWNER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 AFTER DELIVERY CHECK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 RIGHT, LEFT, FRONT AND REAR SIDES OF THE MACHINE . . . . . . . . . . 4 IDENTIFICATION NUMBERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 MACHINE COMPONENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 SAFETY/DECALS/HAND SIGNALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 UTILITY SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 PERSONAL SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 BEFORE OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 MACHINE OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 PARKING THE MACHINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 BURN PREVENTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 FIRE EXTINGUISHER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 FIRE OR EXPLOSION PREVENTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 WHEEL AND TIRE MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 ROLL-OVER PROTECTIVE STRUCTURE . . . . . . . . . . . . . . . . . . . . . . . . 19 READ OPERATORS MANUAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 SAFETY DECALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 HAND SIGNALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 INSTRUMENT/CONTROLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 FRONT CONSOLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 INSTRUMENT PANEL INDICATORS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 INFORMATION CENTER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 GAUGE DISPLAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 TRANSMISSION DISPLAY CENTER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 FOOT PEDALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 SIDE CONSOLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 OPERATORS SEAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93 SEAT BELT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 OPERATING INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99 BEFORE STARTING THE ENGINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99 RUN - IN PROCEDURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99 SEAT BELT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 STARTING THE ENGINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101 STOPPING THE ENGINE AND PARKING THE MACHINE . . . . . . . . . . . . 102 BEFORE YOU OPERATE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106 MACHINE OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109 CONTROL LEVERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112 LOADER FUNCTION SWITCHES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118 LOADER CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 I

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE (First)

TRIM THIS EDGE

TABLE OF CONTENTS

TABLE OF CONTENTS

TRIM THIS EDGE

BRAKE ACCUMULATORS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

DECLUTCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

BUCKET LEVEL INDICATOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

AUXILIARY HYDRAULIC CONNECTION (IF EQUIPPED) . . . . . . . . . . . .

ROTATING BEACON (IF EQUIPPED) . . . . . . . . . . . . . . . . . . . . . . . . . . . .

RIDE CONTROL (IF EQUIPPED) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

COUPLER PIN ENGAGEMENT (IF EQUIPPED) . . . . . . . . . . . . . . . . . . . .

LOADER OPERATING TIPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

TOWING THE MACHINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

TRANSPORTING THE MACHINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

OPERATING IN COLD WEATHER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

OPERATING IN HOT WEATHER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

WHEELS/TIRES/BALLAST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

TIRE PRESSURE CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

LUBRICATION/FILTERS/FLUIDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

GENERAL SAFETY BEFORE YOU SERVICE . . . . . . . . . . . . . . . . . . . . .

SUPPORT STRUT FOR LOADER LIFT ARMS . . . . . . . . . . . . . . . . . . . .

TRANSPORT/SERVICE LINK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SYSTEMGARD LUBRICATION ANALYSIS PROGRAM . . . . . . . . . . . . . .

PLASTIC AND RESIN PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

THE ENGINE HOOD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ENGINE HOURMETER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

FLUIDS AND LUBRICANTS - 721D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

LUBRICATION/MAINTENANCE CHART . . . . . . . . . . . . . . . . . . . . . . . . . .

ACCESS DOORS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

GREASE FITTINGS - 50 HOURS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

GREASE FITTINGS - 100 HOURS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

GREASE FITTINGS - 1000 HOURS . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

GREASE FITTINGS - 50 HOURS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

GREASE FITTINGS - 100 HOURS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

FLUID LEVELS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ENGINE LUBRICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

AIR FILTER SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ENGINE COOLING SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

DIESEL FUEL SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

HYDRAULIC/BRAKE SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

TRANSMISSION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

AXLES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

CAB AIR FILTERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

II

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

121 121 122 122 123 123 124 125 127 128 130 132 133 137 139 139 140 141 142 142 143 144 145 146 147 149 150 152 153 154 155 159 164 168 171 175 180 183 187

MAINTENANCE/ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 191 CAB SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 191 TRANSMISSION CLUTCH CALIBRATION . . . . . . . . . . . . . . . . . . . . . . . . . 194 DECLUTCH ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195 SECONDARY STEERING CHECK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196 PARKING BRAKE CHECK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 197 LOADER ADJUSTMENTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 199 BUCKET HEIGHT CONTROL MINOR ADJUSTMENT . . . . . . . . . . . . . . . 205 ROLL-OVER PROTECTIVE STRUCTURE . . . . . . . . . . . . . . . . . . . . . . . . 206 TORQUE SPECIFICATIONS FOR ROPS CAB AND ROPS CANOPY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 207 TORQUE SPECIFICATIONS FOR SEAT AND SEAT BELTS . . . . . . . . . . 209 ALTERNATOR BELT AND AIR CONDITIONING COMPRESSOR BELT . 210 FIRE EXTINGUISHER MOUNTING (IF EQUIPPED) . . . . . . . . . . . . . . . . . 211 ELECTRICAL SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 213 BATTERY SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 213 FUSES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 216 REPLACEMENT FUSES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 217 SERVICE ELECTRICAL CONNECTOR (IF EQUIPPED) . . . . . . . . . . . . . . 218 AUXILIARY POWER OUTLET (IF EQUIPPED) . . . . . . . . . . . . . . . . . . . . . 218 AUXILIARY POWER EQUIPMENT MOUNTING BRACKET LOCATION . 219 REPLACEMENT BULBS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220 MACHINE STORAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 221 SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 223 ENGINE DATA 721D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 223 OPERATING DATA AND DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . 224-226 SPECIAL BOLT TORQUES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 229

III

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

TABLE OF CONTENTS

TABLE OF CONTENTS

TRIM THIS EDGE IV

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

BD03A017

721D Read this manual before you start the engine or operate the machine. If you need more information, see your dealer.

Your dealer can give you help with Case approved service parts. Your dealer has specially trained technicians who know the best methods of repair and maintenance for your machine.

Use this manual as a guide. Your Wheel Loader will remain a reliable working tool as long as it is kept in working condition and serviced properly.

1

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE (First)

TRIM THIS EDGE

TO THE OWNER

TO THE OWNER

TRIM THIS EDGE

BD03A050

DO NOT operate or permit anyone to operate or service this machine until you or the other persons have read and understand the safety, operation and maintenance instructions in this manual. Use only trained operators who have demonstrated the ability to operate and service this machine correctly and safely.

This Wheel loader, with standard equipment and attachments, is intended to be used for above ground level digging and general earth moving purpose such as land leveling, truck loading, and material rehandling. This machine is not intended to be used for lifting other objects or transporting loads at high speeds.

DO NOT use this machine for any application or purpose other than those described in this manual. If the loader is to be used in a application that involves special attachments or equipment, such as forestry, etc., consult an authorized dealer or the Case, LLC. Consult an authorized dealer or Case, LLC. on changes, additions or modifications that can be required for this machine to comply with various country regulations and safety requirements. Unauthorized modifications will cause ser ious injur y or death. Anyone making such unauthor ized modifications is responsible for the consequences.

This Operators Manual is to be stored in the manual compartment equipped on this machine. Make sure this manual is complete and in good condition. Contact you dealer to obtain additional manuals. Contact your dealer for any further information or assistance about your machine. Your dealer has Case, LLC. approved service parts. Your dealer has technicians with special training that know best methods of repair and maintenance for your Wheel Loader.

2

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

TO THE OWNER Before permitting a new operator on this machine, make sure: 1. That the operator has received the necessary training on how to operate the machine correctly and safely.

2. That the operator has read and understood the instructions given in this manual.

Call your dealer if you need any assistance or information.

Operator Manual Storage Compartment READ THIS MANUAL COMPLETELY and make sure you understand the controls. All equipment has a limit. Make sure you understand the speed, brakes, steering, stability and load characteristics of this machine before you start to operate.

TRIM THIS EDGE

DO NOT remove this manual or the safety manual from the machine. See your dealer for additional manuals. Also see the manual information on the inside of the rear cover of this manual.

1

1. OPERATORS MANUAL STORAGE COMPARTMENT

3

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

BD02N210

TO THE OWNER

AFTER DELIVERY CHECK Two copies of the After Delivery Check are in the back of this manual. One copy is for you and one copy is for the dealer. Make sure that your dealer does the After Delivery Check after the first 100 hours of machine operation.

RIGHT, LEFT, FRONT AND REAR SIDES OF THE MACHINE Right-hand and left-hand, when used in this manual, indicate the right and left sides of the machine as seen from the operators seat.

RIGHT SIDE

FRONT

REAR

TRIM THIS EDGE

LEFT SIDE B891464J

4

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

TO THE OWNER

IDENTIFICATION NUMBERS Write your machine Product Identification Number (P.I.N.) and Serial numbers on the lines provided below. If needed, give these numbers to your dealer when you need parts or information for your machine.

Make a record of the numbers. Keep the record and your Manufacturer’s Statement of Origin in a safe place. If the machine is stolen, report the numbers to your local law enforcement agency.

MACHINE MODEL NUMBER PRODUCT IDENTIFICATION NUMBER ENGINE SERIAL NUMBER TRANSMISSION MODEL AND SERIAL NUMBER TRIM THIS EDGE

ROPS CAB OR CANOPY SERIAL NUMBER FRONT AXLE MODEL AND SERIAL NUMBER REAR AXLE MODEL AND SERIAL NUMBER BUCKET OR ATTACHMENT PART NUMBER

Product Identification Number (P.I.N.)

RB97D048 BD00M072

5

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TO THE OWNER

Engine

Loader Bucket

BD02N229

RP95K195

Transmission

ROPS Cab and Canopy

TRIM THIS EDGE BD02N124

RD98K304

Axle

BD02N126

6

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

TO THE OWNER

MACHINE COMPONENTS 2 3 4 1

6

9 7

8

BD03A017

1.

2.

3.

4.

5.

6.

7.

8.

9.

HAND RAILS ROPS CAB LOADER CONTROLS BUCKET CYLINDER LOADER ARMS BUCKET TRANSPORT SERVICE LINK TRANSMISSION CHECK AND FILL (OPTIONAL COVER SHOWN) STEPS

7

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

5

TO THE OWNER

6 1

5

3

4

2

TRIM THIS EDGE

BD03A058

1. ENGINE HOOD 2. COUNTERWEIGHT AND DRAWBAR 3. BATTERY COVER (ONE EACH SIDE)

4. HAND RAILS 5. LOADER ARM SUPPORT STRUT 6. RADIATOR ACCESS

6 1 5 4 2

3 BD03A053

1. HYDRAULIC & TRANSMISSION COOLER ACCESS 2. BATTERY COVER (ONE EACH SIDE) 3. HYD AND TRANS FILTER ACCESS (OPTIONAL COVER SHOWN)

4. BELLCRANK 5. CAB FILTER FUSE ACCESS 6. EMERGENCY EXIT

8

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

SAFETY/DECALS/HAND SIGNALS SAFETY RULES Most accidents involving machine operating and maintenance can be avoided by following basic safety rules and precautions. Read and understand all the safety messages in this manual, the safety manual and the safety signs on the machine before you operate or service the machine. See your dealer if you have any questions.

READ THIS MANUAL COMPLETELY and make sure you understand the controls. All equipment has a limit.

Make sure you understand the speed, brakes, steering, stability and load characteristics of this machine before you start to operate.

DO NOT remove this manual or the safety manual from the machine. See your dealer for additional manuals. Also see the manual infor mation on the inside of the rear cover of this manual.

BD02N210

1. OPERATORS MANUAL STORAGE BOX

The safety information given in this manual does not replace safety codes, insurance needs, federal, state or local laws. Make sure that your machine has the correct equipment according to these rules or laws.

IMPORTANT: Safety messages in this section point out situations which can happen during the normal operation and maintenance of your machine. These safety messages also give possible ways of dealing with these conditions.

Additional safety messages are used in the text of the manual to show specific safety hazards.

!

WARNING: This safety alert symbol indicates important safety messages in this manual. When you see this symbol, carefully read the message that follows and be alert to the possibility of death or serious injury.

M171C

9

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE (First)

TRIM THIS EDGE

1

SAFETY/DECALS/HAND SIGNALS

!

UTILITY SAFETY

!

Safety precaution MUST be followed when working near buried Utility Lines During operation it is likely that you will be working around or near buried utility lines which may include, but are not limited to: ●

Electrical Power LIne

●

Gas Line

●

Water Line

●

Communication LIne - Telephone or Cable Television

●

Sewer Line

TRIM THIS EDGE

Before beginning any loading or other construction work it is your responsibility to be aware of all such utility lines buried in the area of your project and to avoid them.

RH99G001

CALL ALL LOCAL UTILITY COMPANIES BEFORE YOU TRENCH/DRILL

A LWAY S h a v e a l l l o c a l u t i l i t y companies mark the location of their lines.

Know the utility color code (U.S.A. and Canada): 1. Electric.................................... Red 2. Gas, Oil or Petroleum .......... Yellow 3. Communication, Telephone, Television ........................... Orange 4. Water ......................................Blue 5. Sewer........................Green/Brown 6. Proposed Excavation............White 7. Surveying................................ Pink 8. Reclaimed Water,Slurry ...... Purple

In U.S.A. and Canada call one of many “One Call System Directory” services. If you do not know the local number, call t he n a t i o n al num b e r ( U. S. A . a n d Canada only): 1-888-258-0808.

Check with local authorities for laws, regulations and/or strict penalties requir ing you to locate and avoid existing utilities.

After locating the utility lines, carefully dig a hole by hand and/or automatic vacuum equipment to the utility line to verify the location and depth of the line.

10

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

SAFETY/DECALS/HAND SIGNALS

! PERSONAL SAFETY

!

Safety Decals on this machine use the words Danger, Warning or Caution, which are defined as follows: ●

DANGER: Indicates an immediate hazardous situation which, if not avoided, will result in death or serious injury. The color associated with Danger is RED.

●

WARNING: Indicates a potentially hazardous situation which, if not avoided will result in serious injury. The color associated with Warning is ORANGE.

●

CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices. The color associated with Caution is YELLOW.

●

The first panel indicates the nature of the hazard.

●

The second panel indicates the appropriate avoidance of the hazard.

●

Background color is YELLOW.

●

Prohibition symbols such as

and

STOP

11

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

if used are RED.

TRIM THIS EDGE

ISO two panel pictorial symbol decals are defined as follows:

SAFETY/DECALS/HAND SIGNALS

! BEFORE OPERATION ●

Avoid loose fitting clothing, loose or uncovered long hair, and jewelry.

●

Different jobs will require different protective equipment. Items such as hard hats, protective shoes, heavy gloves, reflector type vests, respirators, ear protection, and eye protection can be required. Before you start the job, determine what protective equipment is required.

Use this equipment at all times.

●

●

!

To avoid falling, always face the machine and use the hand rails and steps when getting on or getting off.

Do not rush.

1

1

Be prepared for emergencies.

Always have a first aid kit and a working fire extinguisher with you and know how to use each.

2

Know the hand signals used on your job. Follow the instructions of the flagman, signs, etc. See Hand Signals starting on page 34.

●

●

Check that all doors, guards, and covers are installed correctly or closed.

Remove all loose objects from the cab. Loose objects can jam controls and cause accidents.

●

●

Foreign material or grease on the steps and hand rails can cause an accident. Keep the steps and hand rails clean.

Before you start each day, walk around the machine and check for oil or fluid leaks. Replace all broken or missing parts and do the required lubrication and maintenance as shown in this manual. Clean all trash and debris from the machine, especially from the engine area.

●

TRIM THIS EDGE

BD03A060

1. HAND RAILS 2. STEPS

12

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

SAFETY/DECALS/HAND SIGNALS Make sure all persons are away from the machine before you start the engine.

●

Before you start the engine, always fasten the seat belt.

●

Before you operate at night, check that all lamps illuminate.

●

Engine exhaust fumes can cause death. If you operate this machine in an enclosed area, make sure there is ventilation to replace the exhaust fumes with fresh air.

●

Know the rules, laws, and safety equipment necessary for transporting this machine on a road or highway.

●

If your machine has a cab make sure that all windows are clean and that the windshield wipers work correctly.

! MACHINE OPERATION ●

Check all controls in a clear area and make sure the machine is operating correctly.

●

Do not allow other persons to ride on the machine. Other persons can fall or can cause an accident. This is a one person machine with one operator’s seat.

●

Dust, fog, smoke, etc., can decrease your vision and cause an accident.

Stop the machine or decrease the speed until you can see everything around you in the work area. Make sure the machine lamps are ON.

●

Contact with high voltage power lines, underground cables, etc., can cause serious injury or death from electrocution.

!

●

Before you drive or operate in an area with high voltage lines, cables, or a power station, tell the power or utility company what you are going to do. You MUST HAVE THE POWER DISCONNECTED OR KEEP A SAFE WORKING DISTANCE from the lines, cables, or power station. Keep all parts of the machine at least 4.6 m (15 feet) away from the power source. You must also know any federal, state/provincial, or local safety codes or regulations that apply to the job site.

●

If a part of the machine touches high voltage power:

●

Warn other workers NOT TO TOUCH THE MACHINE and to stay away from the machine.

●

If you can break contact, reverse the operation that caused contact with the high voltage power, and move the machine away from the danger area. If you cannot break contact, stay in the machine until the utility company de-energizes the line and tells you that the power is off.

13

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

●

SAFETY/DECALS/HAND SIGNALS ●

●

If you have extreme conditions, such as a fire, etc., and you are forced to leave the machine, do not step off the machine. Jump as far from the machine as possible with your feet together and do not touch the ground with your hands.

Then, hop away with your feet together until you are a safe distance from the machine and the electrical current. Do not take large steps.

Because of the voltage differential across the ground, one foot can be in a higher voltage area than the other foot. This difference can kill you.

TRIM THIS EDGE

●

Do not operate the machine if you do not feel well. This can be dangerous for you and for the people around you.

●

You must make a judgment if weather, road, or earth conditions will permit safe operation on a hill, ramp, or rough ground.

●

Stay away from hazardous areas such as ditches, overhangs, etc.

Walk around the work area before you start and look for hazards.

●

Be alert and always know the location of all workers in your area.

Keep all other persons completely away from your machine. Injury or death can result if you do not follow these instructions.

●

Keep the loader bucket low when moving around the work area and be careful when you raise the load to dump.

●

Operate the machine within the specified capacities and limits. Lifting capacities, digging depths, etc, are shown in the Specifications section of this manual.

●

Operate the machine controls from the operators seat only.

●

Digging through underground cables, pipes, lines, etc., can cause injury or death. Learn the location of all underground hazards before you operate your machine in any area.

●

When working in areas where traffic is heavy always have a person direct the traffic and direct other persons for you. Have guard rails, warning signs, etc., as required for your job.

●

Stop operating the machine if a malfunction occurs. Watch the indicator and warning lamps in the machine. Listen and smell for things that are not normal on your machine.

●

Drive around large objects such as large rocks or trees.

14

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

SAFETY/DECALS/HAND SIGNALS

! PARKING THE MACHINE When you park the machine and before you leave the operators area, always support or lower all attachments (loader, backhoe, etc.) to the ground, apply the parking brake, stop the engine, and remove the key.

●

If you must temporarily park the machine on a hillside, put the front of the machine toward the bottom of the hill. Make sure the machine is behind an object that will not move. Put blocks in front of each wheel on the downhill side.

●

Always face the machine and use the hand rails and steps when getting off. Do not rush and do not jump from the machine.

! BURN PREVENTION ●

Batteries contain sulfuric acid which can cause severe burns. Avoid contact with skin, eyes, or clothing.

Antidote - EXTERNAL - Flush with water. INTERNAL - Drink large quantities of water or milk. DO NOT induce vomiting. Seek medical attention immediately. EYES - Flush with water for 15 minutes and seek medical attention immediately.

BATTERIES PRODUCE EXPLOSIVE GASES. Keep sparks, flame, cigars and cigarettes away.

Ventilate when charging or using in enclosed area. Always wear eye protection when working with new batteries.

Wash hands after handling. KEEP OUT OF REACH OF CHILDREN.

●

When the battery electrolyte is frozen, the battery can explode if, (1) you try to charge the battery, or (2) you try to jump start and run the engine. To prevent the battery electrolyte from freezing, keep the battery at full charge. If you do not follow these instructions, you or others in the area can be injured.

●

!

Hot coolant can spray out if the radiator cap is removed too quickly.

To remove the radiator cap, let the cooling system cool, turn the cap to the first notch, wait until the pressure is released, then remove the cap.

15

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

●

!

SAFETY/DECALS/HAND SIGNALS

! FIRE EXTINGUISHER

!

It is recommended that you have a fire extinguisher on your machine. See your Case dealer for availability.

A dry chemical fire extinguisher is approved for Class A, B, and C fires.

TRIM THIS EDGE 16

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

SAFETY/DECALS/HAND SIGNALS

●

!

Sparks or flame can cause the hydrogen gas in a battery to explode.

To prevent an explosion, do the following:

●

Remove all trash or debris from the machine as required. Especially check the engine area and exhaust system.

1. When disconnecting the battery cables, disconnect the negative (−) cable first; when connecting the batter y cables, connect the negative (−) cable last.

●

If the machine has an oil, fuel, or hydraulic leak, always repair the leak and clean the area before operating.

●

Keep the cooling system clean and maintain the correct coolant level.

●

Make sure that you do not store oily rags or other flammable materials on the machine.

3. Do not short circuit the battery posts with metal items.

●

4. Do not weld, grind, or smoke near a battery. Keep open flame away from the battery.

Before welding or using a torch on the machine, clean the area to be repaired.

●

Check the electrical system for loose connections or frayed insulation.

Repair or replace the loose or damaged parts.

2. When connecting jumper cables to start the engine, use the procedure shown in this manual on page 104.

●

Sparks from the electrical system or engine exhaust can cause an explosion or fire. Before you operate this machine in an area with flammable dust or vapors, use good ventilation to remove the flammable dust or vapors before you start.

●

Engine fuel can cause an explosion or fire. Do not fill the fuel tank while the engine is running.

●

DO NOT smoke while refueling the machine.

●

Use nonflammable cleaning solvent to clean parts.

●

A fire can cause injury or death.

Always have a fire extinguisher near or on the machine. Make sure the fire extinguisher is serviced according to the manufacturer’s instructions.

●

If a fire extinguisher has been used, always recharge or replace the fire extinguisher before operating the machine.

17

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

! FIRE OR EXPLOSION PREVENTION

SAFETY/DECALS/HAND SIGNALS

! MAINTENANCE ●

Before you service the machine, put a Do Not Operate tag on the steering wheel. One Do Not Operate tag is included with your new machine.

Additional tags, part number 3214614, are available from your Case dealer.

●

TRIM THIS EDGE

●

●

●

If you are exposed to or come in contact with hazardous chemicals you can be seriously injured. The fluids, lubricants, paints, adhesives, coolants, etc., used with your machine can be hazardous.

Material Safety Data Sheets (MSDS) provide (1) infor mation about the chemical substances within a product, (2) safe handling procedures, (3) first aid measures, and (4) procedures to be taken when the product is accidentally spilled or released. Material Safety Data Sheets (MSDS) are available from your Case dealer.

Before you ser vice your machine, c h e c k t h e M S D S fo r e a c h f l u i d , lubricant, etc., used in this machine.

This information indicates what the r i s k s ar e a n d how t o s e r v i c e t h e machine safely. Follow this information when servicing the machine.

B9502062

●

!

Improper service or repair procedures can cause injury or death. If you do not understand a service or adjustment procedure, see the service manual for this machine or see your Case dealer.

●

Unauthorized modifications to this machine can cause injury or death.

Do not make unauthorized modifications to this machine.

Always see your Case dealer before you weld, cut, or drill holes in your machine.

Before you service this machine and before you dispose of the old fluids and lubricants, always remember the environment. Do not put oil or fluids into the ground or into containers that can leak.

Check with your local environmental or recycling center or your Case dealer for correct disposal information.

If you must service this machine with the engine running, have another person help you. Follow the instructions in this manual or the service manual. Do not leave the operator’s seat while the engine is running.

Disconnect the batteries before working on the electrical system.

●

When you service this machine, always wear face or eye protection, safety shoes, and other protective items as required.

●

Metal chips or debris can cause eye injury. Always wear eye or face protection when you use a hammer on this machine. Use a hammer with a soft face, such as brass, to drive hardened pins.

18

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

SAFETY/DECALS/HAND SIGNALS

●

Lower the bucket or tool to the ground and block the machine securely. Before working on the machine, if you must service the machine with the loader raised, install the lift arm support shown on page 140. Follow the instructions in this manual when you service the machine.

●

Before welding on this machine, disconnect the battery ground (−).

●

Fluids such as Gasoline, Kerosene, Diesel Fuel, Hydraulic Oil, etc. contain chemicals that can be dangerous to your health and can cause cancer and/or birth defects.

Contact either internally or externally can cause infection or other injury. If any internal or external contact occurs, see your local Poison Control Center or doctor IMMEDIATELY.

Clean the machine regularly. A buildup of grease, dirt, and debris can cause possible injury or machine damage. Keep your work shop clean.

! WHEEL AND TIRE MAINTENANCE ●

Do NOT weld to wheel or rim when a tire is installed. Welding will cause an explosive air/gas mixture that will be ignited with high temperatures. This can happen to tires inflated or deflated. Removing air or breaking bead is not adequate. Tire MUST be completely removed from the rim prior to welding.

●

!

Explosive separation of the tire and/ or rim parts can cause injury or death. When tire service is necessary, have a qualified tire mechanic service the tire.

! ROLL-OVER PROTECTIVE STRUCTURE ●

!

Do not modify ROPS in any manner. Unauthorized modifications such as welding, drilling, cutting, or adding attachments can weaken the structure and reduce your protection. Replace ROPS if it is subjected to roll-over or damage.

Do not attempt to repair.

19

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

●

SAFETY/DECALS/HAND SIGNALS

READ OPERATORS MANUAL D e c a l s w h i c h d i s p l ay t h e “ R e a d Operators Manual” symbol are intended to direct the operator to the O p e r a t o r s M a n u a l fo r f u r t h e r i n f o r m a t i o n r e g a r d i n g s a fe t y, maintenance, adjustments and/or procedures for specific areas of the machine. When a decal displays the following symbol refer to the Operators Manual.

When a decal displays the symbol shown below, refer to the appropriate page of the Service Manual.

BC00G075

“READ SERVICE MANUAL”

TRIM THIS EDGE

237187A1

“READ OPERATORS MANUAL”

SAFETY DECALS

!

WARNING: Injury or death can result if you cannot read a safety decal or if a safety decal is missing. Replace any missing or damaged safety decal and keep all safety decals clean. See your Case dealer for new safety decals.

SB002

Make sure that you read all the safety decals and all instructional decals. Check these decals every day before you start. Clean these decals if you cannot read the words.

When you clean the decals, use only a cloth, water, and soap. Do not use solvent, gasoline, etc.

You must replace a decal if the decal is damaged, missing, or cannot be read. If a decal is on a part that is replaced, make sure the decal is on the new part. See your Case dealer for new decals.

20

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

SAFETY/DECALS/HAND SIGNALS

1

BD00B007 / 382622A1

2

2

BD00B007 / 329051A1

21

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

1

SAFETY/DECALS/HAND SIGNALS

3

3

TRIM THIS EDGE BD00B007 / 364742A1

22

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

SAFETY/DECALS/HAND SIGNALS

4

BD03A026 / 323694A1

5

5

RD98K323 / 3217030

23

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

4

SAFETY/DECALS/HAND SIGNALS

6

6

TRIM THIS EDGE

BD03A026 / 329047A1

7

7

BD03A066 / 328754A1

24

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

SAFETY/DECALS/HAND SIGNALS

8

BD03A026 / 329049A1

9

9

BD03A076 / 328752A1

25

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

8

SAFETY/DECALS/HAND SIGNALS

10

10

TRIM THIS EDGE

BD02N170 / 329044A1

11

11

BD02N177 / 8603092

26

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

SAFETY/DECALS/HAND SIGNALS

13

12

12

TRIM THIS EDGE

13

BD02N181 / 332512A1 / 334456A1

27

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

SAFETY/DECALS/HAND SIGNALS

14

14 15

TRIM THIS EDGE

15

15

BD03A029 / 332512A1 / 8603092

28

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

SAFETY/DECALS/HAND SIGNALS

16 16

TRIM THIS EDGE

16

BD03A008 / BD02N183 / 335889A1

17

17

BD03A026 / 328904A1

29

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

SAFETY/DECALS/HAND SIGNALS

18

18

BD02N139 / 388112A1

19 TRIM THIS EDGE

19

BD03A066 / 328904A1

30

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

SAFETY/DECALS/HAND SIGNALS

20

20

TRIM THIS EDGE

MACHINE TIE DOWN

20

BD01E126 / 94F25 / BD00M032

31

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

SAFETY/DECALS/HAND SIGNALS

21

TRIM THIS EDGE

21

BD01E142 / 407737A2

32

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

SAFETY/DECALS/HAND SIGNALS

22

TRIM THIS EDGE

22

22

BD03A046 / BD03A062 / 412477A1

33

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

SAFETY/DECALS/HAND SIGNALS

HAND SIGNALS It is recommended that you and the flagman on the job use hand signals for communications. Before you start, make sure that you both understand the signals that will be used.

BI97D059

BI97D025

TRIM THIS EDGE

START ENGINE

STOP ENGINE

BP97D022

BP97D023

COME TO ME

ALL STOP AND HOLD

Move hands forward and rearward (palms in)

Move hands forward and rearward (palms out).

34

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

SAFETY/DECALS/HAND SIGNALS

BP97D030

BP97D060

ALL STOP AND HOLD

TRIM THIS EDGE

GO THIS FAR

BI97D029

BI97D021

STOP

EMERGENCY STOP

Move one hand back and forth.

BI97D027

LOWER BUCKET

BI97D028

RAISE BUCKET

35

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

SAFETY/DECALS/HAND SIGNALS

BI97D020

BI97D026

RAISE BUCKET SLOWLY

LOWER BUCKET SLOWLY

TRIM THIS EDGE BI97D034

BI97D033

TURN MACHINE LEFT SWING LOAD LEFT

TURN MACHINE RIGHT SWING LOAD RIGHT

To stop movement, stop moving hand and make a fist

To stop movement, stop moving hand and make a fist.

36

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

INSTRUMENT/CONTROLS FRONT CONSOLE

2

3

1

BD02N185

1. FOUR-WAY FLASHER SWITCH: Push the LH side of the of the flasher switch to actuate the flashers.

Push the RH side of the flasher switch for the OFF position.

BC00B087

BC00B048

2. PILOT CONTROL SWITCH: Push on the LH side of the switch to disable the pilot controls, the pilot control lamp will illuminate when the hydraulic control levers are disabled. The loader linkage will stay in position when the pilot controls are disabled. Push on the RH side of the switch to actuate the pilot controls. The hydraulic control levers will now function.

3. UP/DOWN COUNT SWITCH: Controls display, used with Program/Reset Switch (see Program Control in this manual for more information).

BC00B085

BS98M034

BC00B101

BS98M034

4. PROGRAM/RESET SWITCH: Control display, used with Up/Down Count Switch (see Program Control in this manual for more information).

37

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE (First)

TRIM THIS EDGE

4

INSTRUMENTS/CONTROLS

FRONT CONSOLE

6

5

BD02N185

TRIM THIS EDGE

D

5. ENGINE DIAGNOSTIC SWITCH: The service technican will use this switch to analyze engine information.

6. ENGINE GRID HEATER INDICATOR LAMP: To start the engine, turn the key switch to the ON position. The indicator (6) illuminates when the engine grid heater is operating. Wait until the indicator light goes OFF before moving the key switch to the START position to star t the engine. The indicator light may come on again during cranking and shortly after the engine starts for post heating of the air. This allows for smooth running conditions during cold weather warm up.

38

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

INSTRUMENTS/CONTROLS 7. TRANSMISSION CONTROL LEVER: The transmission control lever is used to shift the transmission gears from 1st through 4th gear. Turn the transmission control lever away from you to select a higher gear or toward you to select a lower gear. This control lever is also used to put the transmission in F O RWA R D, NEUTRAL and REVERSE.

B. The center NEUTRAL.

position

is

C. Move the control lever toward you for REVERSE.

TRIM THIS EDGE

7

RD98K322

NOTE: The F-N-R function of the Transmission Control Lever may be moved to the Loader Control Lever for operating efficiency. See page 113 and 114 of this manual.

A

B

C BS00B351

A. Move the control lever away from you for FORWARD.

39

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

INSTRUMENTS/CONTROLS

10

8

11 BD00M085 RD98K311

TRIM THIS EDGE

8. STEERING WHEEL TILT CONTROL: This control has multiple positions. Pull the handle up and adjust the steering wheel to the correct angle. Release the control to hold in that position. Tilt the steering wheel completely up when leaving the machine. Always adjust the steering wheel to the correct position before starting the engine.

10. HORN: Push the hor n button to actuate the horn.

11. TURN SIGNAL LEVER: Push the control lever up to signal a left turn. Pull the control down to signal a BS00B352 right turn. You must move the control lever to the center position to stop the signal.

9

BDO2N195

9. WATER IN FUEL INDICATOR LAMP: Located on the upper left-hand side of the steering column this lamp will illuminate upon starting momentarily. If the lamp stays on the operator should follow procedures for removing water from the fuel system.

40

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

INSTRUMENTS/CONTROLS To Engage the Parking Brake:

12

NOTE: The service brake must be at operating pressure before the parking brake can be released to move the machine. The Brake Pressure Indicator Lamp must not be illuminated when disengaging the Parking Brake.

Attempting to move the machine before the service brake pressures are completely built up to operating pressure can result in premature Park Brake pad wear.

BD02N211

12. PARKING BRAKE SWITCH: NOTE: Make sure the machine has come to a BC00B095 complete stop before applying the parking brake.

IMPORTANT: The Parking Brake is a spring applied, hydraulic released brake, which is applied to the drive shaft. It is effective in holding the machine in place when used correctly.

41

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

1. Push down on the to of the park b r a ke sw i t c h t o E N G AG E t h e parking brake. The parking brake will also engage whenever the key sw i t c h i s m o v e d t o t h e O F F position.

INSTRUMENTS/CONTROLS

Parking Brake Release: A. (For Transmission FNR control to be at the Transmission Control Lever at the Left Side steering wheel).

All following steps are required: 1. Service Brake pressure must be at operating pressure.

2. Transmission Control Lever must be in neutral.

3. Push down on the bottom of the parking brake switch to release the Parking Brake Switch.

4. Step on the Service Brake pedal to take control of the machine.

5. Place the transmission control lever in either FORWARD or REVERSE to move the machine.

B. (For Transmission FNR control to be at the Right Side of the steering wheel in the hydraulic controller area).

All the following steps are required:

TRIM THIS EDGE

1. Service Brake pressure must be at operating pressure.

2. Left Side FNR of Transmission Control Lever must be in Neutral.

3. Right Side FNR switch must be in Neutral.

4. Machine speed is zero.

5. Engine should be running.

6. Push down on the top of the Transmission Enable Switch located in the side Console. (The indicator light on the bottom of the enable switch will illuminate when activated).

7. Push down on the bottom of the parking brake switch to release the Parking Brake. (Must occur within 8 seconds of Enable).

8. Step on Service Brake pedal to take control of the machine. (Must occur within 8 seconds of Enable).

9. Place the right side FNR switch in either FORWARD or REVERSE to move the machine. (Must occur within 8 seconds of Enable).

IMPORTANT: A failure in the operating procedure or a failure in the electrical or hydraulic function can result in abrupt engagement of the Paring Brake. Always wear your seat belt.

42

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

INSTRUMENTS/CONTROLS

12 RB99J178

START POSITION Turn the key to this position to engage the starter motor to star t the engine. The RB99J176 switch is spring loaded and will retur n to the ON position when released.

TRIM THIS EDGE

RD98K312

318764A

13. Key Switch The key switch has four positions:

RB98M031

ON POSITION This position energizes all electrical systems. The key will return to this position after you release the key from the START position.

ACCESSORY POSITION This position will energize the optional radio only. It will not energize the instruments or star t the engine.

OFF POSITION A l l sw i t c h c o n t r o l l e d current is OFF. Turn the key t o O FF t o s top th e RB99J175 engine. Remove the key and turn the Master Disconnect Switch to OFF.

43

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

INSTRUMENTS/CONTROLS

INSTRUMENT PANEL INDICATORS Instrument Cluster The instrument cluster will check each monitored system when you turn the key switch to the ON position. All LED’s (Light Emitting Diodes) will illuminate, six bar graphs will energize for three seconds, and the warning alarm will sound for three seconds. At the end of this check all monitored systems will return to normal operation. If there is an open circuit between a sensor and the instrument cluster, the LED will flash and the warning alarm will sound for 5 seconds.

IMPORTANT: If during operation, the stop master warning lamp (on front console) flashes and the warning alarm is continuous, stop the machine, stop the engine, and find the problem.

TRIM THIS EDGE

2

1

1

BD02N185

1. INDICATOR LAMP FOR FOUR-WAY FLASHER AND TURN SIGNALS: This green indicator lamp will flash when you signal a turn or when you actuate the four-way flashers.

BS96H049

2. BEACON INDICATOR: (If equipped) This indicator illuminates when the Beacon is in the ON position.

BC00B082

44

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

INSTRUMENTS/CONTROLS

INSTRUMENT PANEL INDICATORS

4

6

BD02N185

3. LAMP INDICATOR: This indicator illuminates when the lamps are ON. BS98M062

4. PILOT LOCKOUT INDICATOR: This indicator illuminates when the pilot lockout is actuated.

BC00B048

5. LOW COOLANT INDICATOR: This indicator illuminates when the engine coolant is low. The alarm sounds continuously and the master indicator lamp will be red.

BC00B110

NOTE: Stop the engine and add coolant to the radiator.

6. BRAKE PRESSURE INDICATOR:

BC00B108

This indicator illuminates when the brake system pressure is too low.

The alarm sounds continuously and the stop master indicator will be red.

NOTE: Stop the machine and correct the problem.

45

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

3

5

INSTRUMENTS/CONTROLS

INSTRUMENT PANEL INDICATORS 7

TRIM THIS EDGE

BD02N185

7. STOP MASTER INDICATOR (RED, CRITICAL): The Stop Master Indicator is a critical warning display. See Critical Warning Displays.

Critical Warning Displays When the Stop Master indicator illuminates you must bring the machine safely to a stop and immediately turn OFF the engine. Failure to do so may result in injury and/or damage to the machine. The following table is a listing of critical warning displays that may appear on the instrument cluster and the corrective action required. When a fault occurs, a continuous audible alarm will sound and the Stop Master Indicator will be RED and the display indicator will be illuminated.

BC00B290

Display

Description

Corrective Action

ENGINE OIL PRESSURE

Low Engine Oil Pressure. Below Bring the machine to a safe stop and shut 10 PSI the engine OFF immediately. Contact your Dealer.

BRAKE PRESSURE

Low Brake Pressure

Bring the machine to a safe stop and shut the engine OFF immediately. Contact your Dealer.

Low Steering Pressure.

Bring the machine to a safe stop and shut the engine OFF immediately. Contact your Dealer.

STEERING PRESSURE (W/ AUX STEERING)

46

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

INSTRUMENTS/CONTROLS

Low Coolant Level.

Bring the machine to a safe stop and shut the engine OFF immediately. Check the coolant levels after allowing the engine and the coolant to cool down. Contact your Dealer.

COOLANT TEMPERATURE

High Engine Coolant Temperature.

Bring the machine to a safe stop and shut the engine OFF immediately. Check the coolant levels after allowing the engine and the coolant to cool down. Contact your Dealer.

HYDRAULIC OIL TEMPERATURE

High Hydraulic Oil Temperature.

Bring the machine to a safe stop and shut the engine OFF immediately. Contact your Dealer.

TRANSMISSION OIL TEMPERATURE

High Transmission Oil Temperature.

Bring the machine to a safe stop and shut the engine OFF immediately. Contact your Dealer.

TRIM THIS EDGE

COOLANT LEVEL

47

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

INSTRUMENTS/CONTROLS

INSTRUMENT PANEL INDICATORS 8

TRIM THIS EDGE

BD02N185

8. CAUTION MASTER INDICATOR (YELLOW, NON-CRITICAL): The Caution Master Indicator is a non-critical warning display. See Non - Critical Warning Displays.

Non - Critical Warning Displays When the caution is “on”, change your operating method, schedule a shutdown for maintenance or if the condition persists, contact your dealer. The following table is a listing of warning displays that may appear on the instrument cluster and the corrective action required. When a fault occurs, an audible alarm will sound for 3 seconds and the Caution Master Indicator will be YELLOW and the display indicator will be illuminated. When this occurs return the machine to a service position and shutdown the engine to help avoid expensive repairs.

BC00B291

Display PARKING BRAKE

Description

Corrective Action

Parking Brake engaged and Release the parking Brake. shifts to F or R.

COOLANT TEMPERATURE

High engine coolant temperature

1. Idle machine and monitor temperature.

2. Clean radiator or Operate fan reverser.

(If equipped) 3. If condition persists, contact your dealer.

HYDRAULIC TEMPERATURE

High hydraulic temperature

1.Idle machine and monitor temperature.

2. Clean cooler or Operate fan reverser. (If equipped) 3. If condition persists, contact your dealer.

48

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

TRANSMISSION TEMPERATURE

High transmission temperature

1. Idle machine and monitor temperature.

2. Clean cooler or Operate fan reverser. (If equipped) 3. Use a lower gear.

4. If condition persists, contact your dealer.

AIR CONDITIONING

High or Low air conditioning pressure.

1. Turn air conditioning OFF. 2. Low outside temperature.

3. Servicing required.

4. If condition persists, contact your dealer.

High air filter restriction

1. Clean air filter.

2. Replace primary and secondary filters.

3. If condition persists, contact your dealer.

Transmission filter restriction.

1. Replace transmission filter.

2. If condition persists, contact your dealer.

Hydraulic filter restriction.

1. Replace hydraulic filter.

2. If condition persists, contact your dealer.

Alternator malfunction.

1. Check electrical system.

2. Voltages are out of range.

3. Change operating procedure.

4. If condition persists, contact your dealer.

Low fuel.

1. Fill fuel tank within the next hour.

AIR FILTER

TRANSMISSION FILTER HYDRAULIC FILTER ALTERNATOR

FUEL

49

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

INSTRUMENTS/CONTROLS

INSTRUMENTS/CONTROLS

INSTRUMENT PANEL INDICATORS

9

10

11

TRIM THIS EDGE

BD02N185

9. SECONDARY STEERING INDICATOR (IF EQUIPPED):

BS00B111

This indicator illuminates when the primary steering system pressure is too low. The alarm sounds continuously and the stop master indicator turns red.

NOTE: If this situation occurs, stop the machine immediately and contact your dealer.

10. PARKING BRAKE INDICATOR:

BS96H049

This indicator illuminates when the parking brake is applied. When the parking brake is applied and you shift the transmission into FORWARD or REVERSE the alarm sounds for 3 seconds and the caution master indicator turns yellow.

11. AIR CONDITIONING INDICATOR: (If equipped)

This indicator illuminates when the air conditioner has stopped due to refrigerant pressures that are too high or too low. The alarm sounds for 3 seconds and the caution master indicator turns yellow. The BC00B112 system needs service or the outside air temperature is too cool for the system to work.

IMPORTANT: To start the air conditioner again, turn the air conditioning temperature control to the OFF position and back to the ON position again. If the indicator lamp stays ON, see your Service Manual or your dealer.

50

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

INSTRUMENTS/CONTROLS

INSTRUMENT PANEL INDICATORS

12 13

BD02N185

12. HYDRAULIC OIL FILTER INDICATOR:

BC00B113

This indicator illuminates when the hydraulic filter is restricted and requires service. The alarm sounds for 3 seconds and the caution master indicator turns yellow. Service the filter as required.

13. AIR FILTER INDICATOR:

BS98M026

This indicator illuminates when the air filter is restricted and requires service. The alarm sounds for 3 seconds and the caution master indicator turns yellow.

14. TRANSMISSION OIL FILTER INDICATOR

BS99J182

This indicator illuminates when the transmission filter is restricted and requires service. The alarm sounds for 3 seconds and the caution master indicator turns yellow. Service the filter as required.

51

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

14

INSTRUMENTS/CONTROLS

INSTRUMENT PANEL INDICATORS

15

BD02N185

TRIM THIS EDGE

15. TRANSMISSION OIL TEMPERATURE GAUGE: The transmission oil temperature gauge is shown with indicator bars.

Normal operating temperature is in the green zone. When the transmission oil temperature increases, the bars move into the yellow BS98M028 zone and begin to flash, the warning alarm sounds for three seconds, and the caution master indicator turns yellow. When the temperature continues to increase the bars move into the red zone and continue to flash, the warning alarm will sound continuously, and the stop master indicator turns red.

The machine must not be operated when the temperature is in the red zone. .

TRANSMISSION OIL TEMPERATURE GAUGE Gauge Indication

Condition

Master Indicator

Gauge Status

Alarm Status

20°C and below (68°F and below)

Oil temperature is very low

Caution (Yellow)

Flashes

3 Seconds

20 to 120°C (68 to 248°F)

Oil temperature is normal Caution (Yellow)

Flashes

3 Seconds

Flashes

Continuous

120 to 125°C Oil temperature is high (248 to 257°F) (See the note below.)

125°C and above (257°F and above)

Oil temperature is very high Stop (Red)

NOTE: To prevent damage to the transmission, stop the machine, shift the transmission to NEUTRAL, and run the engine at full throttle until the transmission cools. If the transmission oil temperature does not return to normal operating temperature, run the engine at idle speed and check the transmission oil level.

Correct the problem before continuing to operate the machine 52

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

INSTRUMENTS/CONTROLS

INSTRUMENT PANEL INDICATORS

BD02N185

16. HYDRAULIC OIL TEMPERATURE GAUGE: The Hydraulic Oil Temperature Gauge indicates the oil temperature of the hydraulic system. The hydraulic oil temperature gauge is shown with indicator bars. Normal operating temperature is in the green BC00B123 zone. When the hydraulic oil temperature increases the bars move into the yellow zone and begin to flash, the warning alarm sounds for three seconds, and the caution master indicator turns yellow. When the temperature continues to increase the bars move into the red zone and continue to flash and the warning alarm sounds continuously. The stop master indicator turns red. The machine must not be operated when the temperature is in the red zone.

HYDRAULIC OIL TEMPERATURE GAUGE Gauge Indication

Condition

Master Indicator

Gauge Status

Alarm Status

20°C and below (68°F and below)

Hydraulic oil temperature is very low

Caution (Yellow)

Flashes

3 Seconds

20 to 105°C (68 to 221°F)

Hydraulic oil temperature is normal

105 to 110°C (221 to 230°F)

Hydraulic oil temperature is high

Caution (Yellow)

Flashes

3 Seconds

110°C and above (230°F and above)

Hydraulic oil temperature very high

Stop (Red)

Flashes

Continuous

NOTE: Stop the machine and correct the problem.

53

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

16

INSTRUMENTS/CONTROLS

INSTRUMENT PANEL INDICATORS

17 TRIM THIS EDGE

BD02N185

17. VOLT METER GAUGE: The volt meter gauge indicates the condition of the batteries and charging system. The amount of voltage is shown with indicator bars.

Normal operating range is in the green zone. When the voltage BS98M032 increases or decreases the bars move into the yellow zone and begin to flash, the warning alarm sounds for three seconds, and the caution master indicator turns yellow.

VOLTMETER GAUGE Gauge Indication 0 to 18 Volts

18 to 24 Volts

Engine Speed Condition o f Charging System

Master Indicator Stopped or low Very low battery charge Caution idle (Yellow)

Stopped or low idle Above low idle

26 to 32 Volts 32 Volts and above (See the note below.)

Alarm Status

Flashes

3 Seconds

3 Seconds

Stopped or low Low to normal battery idle charge Above low idle

24 to 26 Volts

Gauge Status Flashes

Above low idle

Problem system

in

charging

Normal battery charge Problem system

in

charging

Normal operating range Problem in charging Caution system (overcharging) (Yellow)

NOTE: Stop the machine and correct the problem.

54

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

INSTRUMENTS/CONTROLS

INSTRUMENT PANEL INDICATORS

BD02N185

18. FUEL LEVEL GAUGE: The Fuel Level Gauge indicates the fuel level. The fuel level is shown on the gauge with indicator bars. Normal operating range is in the green zone. When the tank is almost empty the bars move into the BS98M034 yellow zone and begin to flash, the warning alarm sounds for three seconds, and the caution master indicator turns yellow.

NOTE: The fuel level can be checked without the key switch being turned to the ON position, by pushing in and holding the right side of the program reset switch.

FUEL LEVEL GAUGE Gauge Indication

Condition

Master Indicator

Gauge Status

Alarm Status

5 percent and below

Fuel level low

Caution (Yellow)

Flashes

3 Seconds

5 percent and above

Fuel level normal

55

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

18

INSTRUMENTS/CONTROLS

INSTRUMENT PANEL INDICATORS

19 TRIM THIS EDGE

BD02N185

19. ENGINE OIL PRESSURE GAUGE The Engine Oil Pressure Gauge indicates the oil pressure in the engine lubrication system. The engine oil pressure is shown with indicator bars. Normal operation is in the green zone. When the oil BS99D060 pressure decreases below a safe operating pressure, the bars move into the red zone and flash and the warning alarm sounds continuously.

The stop master indicator turns red. The machine must not be operated when the oil pressure is in the red zone.

ENGINE OIL PRESSURE GAUGE Gauge Indication

Condition

Master Indicator

Gauge Status

Alarm Status

0 to 70 kPa (0 to 10 psi)

Very low (too low to run engine)

Stop (Red)

Flashes

Continuous

70 kPa and above 10 psi and above)

Normal (above low idle)

NOTE: Stop the engine immediately and correct the problem.

56

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

INSTRUMENTS/CONTROLS

INSTRUMENT PANEL INDICATORS

BD02N185

20. ENGINE COOLANT TEMPERATURE GAUGE: The Engine Coolant Temperature gauge indicates the coolant temperature of the engine. The engine coolant temperature is shown with indicator bars. Normal operating temperature is in the BS98H053 green zone. When the engine coolant temperature increases the bars move into the yellow zone and begin to flash, the warning alarm sounds for three seconds. The caution master indicator turns yellow. When the temperature continues to increase the bars move into the red zone and continue to flash and the warning alarm sounds continuously. The stop master in di c ato r tu r ns r ed. Th e ma c hi ne M US T N OT be o pe rate d wh en th e temperature is in the red zone.

ENGINE COOLANT TEMPERATURE GAUGE Gauge Indication

Condition

Master Indicator

Gauge Status

Alarm Status

20°C and below (68°F and below)

Coolant temperature is very low

Caution (Yellow)

Flashes

3 Seconds

20 to 105°C (68 to 221°F)

Coolant temperature is normal

105 to 110°C (221 to 230°F)

Coolant temperature is high

Caution (Yellow)

Flashes

3 Seconds

Stop (Red)

Flashes

Continuous

110°C and above Coolant temperature (230°F and above) (See the is very high note below.)

NOTE: Stop the engine immediately and correct the problem.

57

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

20

INSTRUMENTS/CONTROLS

INSTRUMENT PANEL INDICATORS

21

TRIM THIS EDGE

BD02N185

21. NOT USED ON THIS MODEL

BC00B080

58

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

INSTRUMENTS/CONTROLS

INFORMATION CENTER

A B

C

D

BD02N185

A. UP COUNT B. DOWN COUNT

C. PROGRAM D. RESET

1. INFORMATION CENTER You can display many of the machine functions on your Programmable Information Center. It can be programmed to display all functions, or only the functions that are important to you.

Here are the functions you may choose to see on your Information Center: HOURMETER - Displays the accumulated running time of the engine in hours and tenths of an hour with an “hour glass” symbol.

NOTE: Machine hour can be checked with out the key switch being in the ON position, by pushing in and holding the right side of the program reset switch.

TACHOMETER - Displays the engine speed in revolutions per minute along with an “n/min” symbol.

SPEEDOMETER - Displays the ground speed in either kilometers per hour (km/h) or miles per hour (mph) along with either an “km/h or mph” symbol.

ENGINE COOLANT TEMPERATURE - Displays the engine coolant temperature in Celsius with the engine coolant temperature bar graph flashing.

ENGINE OIL PRESSURE - Displays the engine oil pressure in kilo pascals (kPa) with the engine oil pressure bar graph flashing.

FUEL LEVEL - Displays the fuel level in percent (%) remaining from a full tank with the fuel level bar graph flashing.

59

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

1

INSTRUMENTS/CONTROLS

INFORMATION CENTER

A B C

D

1

TRIM THIS EDGE

BD02N185

A. UP COUNT B. DOWN COUNT

C. PROGRAM D. RESET

TRANSMISSION OIL TEMPERATURE - Displays the transmission oil temperature in Celsius with the transmission oil temperature bar graph flashing.

HYDRAULIC OIL TEMPERATURE - Displays the hydraulic oil temperature in Celsius with the hydraulic oil temperature bar graph flashing.

VOLTMETER - Displays the electrical system voltage level in volts with the voltmeter bar graph flashing.

Programming Your Information Center NOTE: To program your instrument cluster the machine must be stationary with the parking brake set.

To program your Information Center, you need to use two switches, the up/down count (A, B) switch and the program/reset (C, D) switch. These switches are located on the Right Hand side of the front console.

For an up count (A) press the left side of the up/down count (A, B) switch. For a down count (B) press the right side of the up/down count (A, B) switch.

For programming (C) press the left side of the program/reset (C, D) switch. For resetting (D) press the right side of the program/reset (C, D) switch.

NOTE: The program/reset (C, D) switch is a three position rocker switch. The center position is OFF or NEUTRAL. 60

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

INSTRUMENTS/CONTROLS

INFORMATION CENTER

A B C

D

BD02N185

A. UP COUNT B. DOWN COUNT

C. PROGRAM D. RESET

To program your information center do the following: 1. Turn the key switch to the ON position.

2. Put the Information Center into the program mode by pressing the program switch down (C).

3. Up count (A) to program location 010.

4. Center the program/reset (C, D) switch. This will allow you to adjust to the desired value. You can personalize the cluster to your use (See Gauge Displays in this manual).

5. When adjusted you can push the program/reset (C, D) switch momentarily to the reset position. You have completed the change.

Service Interval Hours Locations 61 through 70 are service interval hour settings. The service interval hours will accumulate hours until they are reset. Once they are reset, they will begin accumulating hours independent from the machine hours until they are reset again.

61

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

1

INSTRUMENTS/CONTROLS

INFORMATION CENTER

A B C

D

1

BD02N185

TRIM THIS EDGE

A. UP COUNT B. DOWN COUNT

C. PROGRAM D. RESET

Example: If the operator wanted location 061 to indicate engine oil service intervals, when the engine oil is changed, location 061 would be reset to begin accumulating hours for the next oil change. The operator could then go into location 061 and monitor the accumulating hours. When location 061 reaches the engine oil change interval, the operator would change the oil and reset location 061 again.

To view the service hour interval locations: ●

Press the program (C) switch (left side of the program/reset (C, D) switch).

●

Press the up count (A) switch until the display reads the desired location (010 070).

●

Return the program/reset (C, D) switch to the OFF (center) position.

●

Read the accumulated hours shown on the Display Center.

To reset the service interval hours: ●

Press the program (C) switch (left side of the program/reset (C, D) switch).

●

Press the up count (A) switch until the display reads the desired location (010 070).

●

Return the program/reset (C, D) switch to the OFF (center) position.

●

Push the down count (B) switch and hold for 3 seconds. The service interval hours in the Display Center will reset to 0.

62

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

INSTRUMENTS/CONTROLS

INFORMATION CENTER

A B C

D

BD02N185

A. UP COUNT B. DOWN COUNT

C. PROGRAM D. RESET

Fault Code Status Locations 071 through 090 displayed fault codes and the hours the faults occurred. The Information Center continuously monitors the machines condition and records any fault codes; however, it will only record a duplicate code once every hour. When a fault code is written, the service indicator icon (a manual with a wrench) will be displayed on the Information Center.

To view the fault codes and the hours they occurred: ●

Press the program (C) switch (left side of the program/reset (C, D) switch).

●

Press the up count (A) switch until the display reads the desired location (071 090).

●

Return the program/reset (C, D) switch to the OFF (center) position.

●

Read any fault codes on the Display Center.

●

Press the program (C) switch again.

●

Press the up count (A) switch one time to advance to the next position.

●

Return the program/reset (C, D) switch to the OFF (center) position.

●

Read the hours at which the previous code occurred.

The hour location will always follow the fault code location.

63

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

1

INSTRUMENTS/CONTROLS

INFORMATION CENTER

A B C

D

1

TRIM THIS EDGE

BD02N185

Example: Location 072 will display the hours on the machine when the fault code in location 071 was written. Location 074 will display the hours on the machine when the fault code in location 073 was written.

You can monitor a particular location without going into the programming mode by performing the following procedure: ●

Press the program (C) switch.

●

Press the up count (A) switch until the location to be monitored is displayed.

●

Return the program/reset (C, D) switch to the OFF (center) position.

●

Press the program/reset switch again and wait for 5 seconds. The numbers on the display will change.

●

Return the program switch program to the OFF (center) position.

08 - Manually scrolls through Hour meter, Tachometer, Speedometer (mph), Engine Temperature (deg. F), Engine Oil Pressure (psi), Fuel Level, Transmission Oil Temperature (deg. F), Hydraulic Oil Temperature (deg. F), and voltmeter.

64

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

INSTRUMENTS/CONTROLS

GAUGE DISPLAY

A B C

D

BD02N185

A. UP COUNT B. DOWN COUNT

C. PROGRAM D. RESET

65

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

1

INSTRUMENTS/CONTROLS 1. Gauge Displays What machine functions your Display Center will show you is determined by a Gauge Display you can control. You have 8 different Gauge Displays you may choose from. Four of them give you the capability to manually scroll through functions, and the other four automatically scroll for you.

01 - Manually scrolls through Hour meter, Tachometer, and Speedometer (km/h).

02 - Manually scrolls through Hour meter, Tachometer, and Speedometer (mph).

03 - Automatically scrolls through Hour meter (at startup), Tachometer (in 1st - 3rd gears), and Speedometer (km/h) (in 4th gear).

04 - Automatically scrolls through Hour meter (at startup), Tachometer (in 1st - 3rd gears), and Speedometer (mph) (in 4th gear).

05 - Manually scrolls through Hour meter, Tachometer, and Speedometer (km/h), Engine Temperature (Celsius), Engine Oil Pressure, Fuel Level, Transmission Oil Temperature (Celsius), Hydraulic Oil Temperature (Celsius), and Voltmeter.

TRIM THIS EDGE

06 - Automatically scrolls through Hour meter (at startup), Tachometer (at startup in neutral), and Speedometer (km/h) (initiating in any actual gear).

07 - Automatically scrolls through Hour meter (at startup), Tachometer (at startup in neutral), and Speedometer (mph) (initiating in any actual gear).

08 - Manually scrolls through Hour meter, Tachometer, Speedometer (mph), Engine Temperature (deg. F), Engine Oil Pressure (psi), Fuel Level, Transmission Oil Temperature (deg. F), Hydraulic Oil Temperature (deg. F), and voltmeter.

66

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

INSTRUMENTS/CONTROLS

GAUGE DISPLAY

A B C

D

BD02N185

A. UP COUNT B. DOWN COUNT

C. PROGRAM D. RESET

Programming Your Gauge Display When you start your machine you will see the Hourmeter in the Display Center.

Your wheel loader is shipped from the factory with Gauge Display 05. To check what Gauge Display your machine currently is using do the following: ●

Press the program (C) switch (left side of the program/reset (C, D) switch).

●

Press the up count (A) switch until the display reads 010.

●

Return the program/reset (C, D) switch to the OFF (center) position.

●

Read the number (01, 02, 03, 04, 05, 06, 07 or 08) shown on the Display Center. If this is the Gauge Display you want, press the reset (D) switch (right side of the program/reset (C, D) switch) momentarily and you are done.

●

If you want a different Gauge Display, press the up count (A) switch until the display reads the Gauge Display you want (between 01 to 08).

●

Press the reset (D) switch (right side of the program/reset (C, D) switch) momentarily.

67

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

1

INSTRUMENTS/CONTROLS

GAUGE DISPLAY

A

B C

D

1

TRIM THIS EDGE

BD02N185

A. UP COUNT B. DOWN COUNT

C. PROGRAM D. RESET

Manual Scrolling Gauge Displays (01, 02, 05 or 08) If you’ve chosen one of the manually scrolling Gauge Displays (01, 02, 05 or 08), you may scroll through the functions by pressing the up count switch.

Example: Lets say you’ve chosen Gauge Display 01. You will first see the Hourmeter in the Display Center. ●

Pressing the up count (A) switch one time will show you the Tachometer.

●

Pressing the up count (A) switch again shows you the Speedometer (km/h).

●

Pressing the up count (A) switch again takes you back to the Hourmeter.

Automatically Scrolling Gauge Displays (03, 04, 06 or 07) If you’ve chosen one of the automatically scrolling Gauge Displays (03, 04, 06 or 07), the Display Center automatically scrolls through functions. Pressing the up count switch has no effect on the display.

Example: Lets say you’ve chosen Gauge Display 03. You will first see the Hourmeter in the Display Center after starting the machine. In 1st - 3rd gears you’ll see the Tachometer in the Display Center, and in 4th gear you’ll see the Speedometer (km/h).

68

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

INSTRUMENTS/CONTROLS

GAUGE DISPLAY

A B C

D

BD02N185

A. UP COUNT B. DOWN COUNT

C. PROGRAM D. RESET

Displaying Individual Functions You also may choose to display any individual function at anytime, regardless of the Gauge Display you’ve chosen. You may show the following functions at any time on your Display Center.

000 - Hourmeter 001 - Tachometer 002 - Speedometer (mph) 003 - Speedometer (km/h) 004 - Engine Coolant Temperature 005 - Engine Oil Pressure 006 - Fuel Level 007 - Transmission Oil Temperature 008 - Hydraulic Oil Temperature 009 - Voltmeter

69

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

1

INSTRUMENTS/CONTROLS

GAUGE DISPLAY

A B C

D

1

TRIM THIS EDGE

BD02N185

A. UP COUNT B. DOWN COUNT

C. PROGRAM D. RESET

To View a Selected Function On Your Display Center do the following: ●

Press the program (C) switch (left side of the program/reset (C, D) switch).

●

Press the up count (A) switch until the display reads the function of your choice (000 - 009).

●

Return the program/reset (C, D) switch to OFF (center) position.

You will now see the function you’ve chosen.

Example: Lets say you were interested in seeing the engine coolant temperature.

You would do the following: ●

Press the program (C) switch (left side of the program/reset switch).

●

Press the up count (A) switch until the display reads 004.

●

Return the program/reset (C, D) switch to the OFF (center) position.

You will now see the engine coolant temperature on your Display Center.

The engine coolant temperature bar graph will flash indicating this is the function being displayed.

70

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

INSTRUMENTS/CONTROLS

GAUGE DISPLAY

A B C

D

BD02N185

A. UP COUNT B. DOWN COUNT

C. PROGRAM D. RESET

Setting Display Center Lamp You can set the brightness of your display lights for two separate conditions. The first is with your work lights OFF, and the second is with the work lights ON. ●

Press the program (C) switch.

●

Press the up count (A) switch until the display reads 012 (for lamps OFF) or 013 (for lamps ON).

●

Return the program/reset (C, D) switch to the OFF (center) position.

●

To increase the brightness of the display lights press the up count (A) switch.

●

To decrease the brightness of the display lights press the down count (B) switch.

●

The brightness can be varied between 001 - 100, with 100 being the brightest.

Your machine is shipped from the factory with brightness setting of 070 for working lights OFF and 020 for lamps ON.

●

Press the reset (D) switch momentarily (0.25 second) and you are done.

71

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

1

INSTRUMENTS/CONTROLS

GAUGE DISPLAY

A B C

D

1

TRIM THIS EDGE

BD02N185

A. UP COUNT B. DOWN COUNT

C. PROGRAM D. RESET

Setting Master Reset This procedure will reset the Information Center to the values set at the factory for the Gauge Display, Information Center lighting for work lights off and work lights on, minimum gear selection in automatic mode, and maximum gear selection. ●

Press the program (C) switch.

●

Press the up count (A) switch until the display reads 042.

●

Return the program/reset (C, D) switch to the OFF (center) position.

●

Press the up count (A) switch to change the reading from 00 to 01.

●

Press the reset (D) switch momentarily (0.25 second) and you are done.

72

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

INSTRUMENTS/CONTROLS

TRANSMISSION DISPLAY CENTER B A

C D

E

RD97F206

C. GEAR D. BAR

E. AUTOMATIC MODE

The Transmission Display will show the status of the transmission control. The Display contains the following information: Direction Selected, shown at the top of the display center: F - Forward N - Neutral R - Reverse F - Flashing forward not engaged.

N - Flashing set control lever to neutral position.

R - Flashing reverse not engaged.

Requested Gear (gear position on shift lever), shown in the center of the gear symbol: 1 - 1st Gear 2 - 2nd Gear 3 - 3rd Gear 4 - 4th Gear Actual Gear, shown with bars to the right of the gear symbol.

The number of bars indicates the gear the transmission is actually in. This may vary from the requested gear when the transmission is in the Automatic Mode.

Transmission Mode (Automatic or Manual), shown in the lower left of the display center. A gear symbol with an “A” in the center will be displayed in the lower left of the display when the transmission is in the Automatic Mode. When the transmission is in the Manual Mode no symbol will be displayed.

73

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

A. F - N - R B. DISPLAY CENTER

INSTRUMENTS/CONTROLS

TRANSMISSION DISPLAY CENTER

A B

C

D

TRIM THIS EDGE

BD02N185

A. UP COUNT B. DOWN COUNT

C. PROGRAM D. RESET

Minimum Gear Selection, Automatic Mode The transmission can be programmed for the lowest gear possible in the automatic mode. The operator can select 1st or 2nd gear. The gear that is chosen will be the gear that the transmission is in when the machine begins to move.

Machines shipped from the factory will have the minimum gear set a 1.

Programming Minimum Gear Selection ●

Press the program (C) switch.

●

Press the up count (A) switch until the display reads 050.

●

Return the program/reset (C, D) switch to the OFF (center) position.

●

Read the number (1 or 2) shown on the Display Center. If this is the gear selection you want, press the program (C) or reset (D) switch.

●

If you want the other minimum gear selection, press the up count (A) switch until the number you want is displayed.

●

Press the reset (D) switch momentarily (0.25 seconds).

74

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

INSTRUMENTS/CONTROLS

TRANSMISSION DISPLAY CENTER

A B D

BD02N185

A. UP COUNT B. DOWN COUNT

C. PROGRAM D. RESET

Maximum Gear Selection, Automatic Mode The transmission can be programmed for the highest gear attainable in the automatic mode or the manual mode. The operator can select 2nd, 3rd or 4th gear. The gear that is chosen is the highest attainable gear that the transmission will be able to reach. Machines shipped from the factory will have the minimum gear set a 4.

Programming Maximum Gear Selection ●

Press the program (C) switch.

●

Press the up count (A) switch until the display reads 051.

●

Return the program/reset (C, D) switch to the OFF (center) position.

●

Read the number (2, 3, or 4) shown on the Display Center. If this is the gear selection you want, press the program (C) or reset (D) switch.

●

If you want a different maximum gear selection gear selection, press the up count (A) switch until the number you want is displayed.

●

Press the reset (D) switch momentarily (0.25 seconds).

75

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

C

INSTRUMENTS/CONTROLS

FOOT PEDALS 1 2

TRIM THIS EDGE

BD02N214

BD02N212

1. FOOT THROTTLE: Push the foot throttle to increase the engine speed. Release the foot throttle to decrease the engine speed.

2. DUAL BRAKE PEDALS: The dual brake pedals function the same as a single and work simultaneously or separate. Pushing either pedal will actuate the brakes

NOTE: Use the DECLUTCH SWITCH when you need maximum power (speed) for the loader lift arms and bucket. See page 83 and 121 in this manual for a detailed explanation.

76

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

INSTRUMENTS/CONTROLS

LOADER CONTROL LEVERS TWO SPOOL VALVE - ONE CONTROL LEVER A

B

E

1 2 1 C

F D AND

BUCKET

3

A. FLOAT (DETENT): This is a detent position. When in the FLOAT (Detent) position, the loader bucket can follow the l evel o f t h e gr ou n d w i t h o u t movement of the control lever

TRIM THIS EDGE

BS01E136 / BS00B353

1. LIFT ARM CONTROL

BS01E142

2. AUXILIARY F-N-R SWITCH: This switch will allow the operator to put t h e Tr a n s m i s s i o n i n For wa r d , Neutral or Reverse. To activate this auxiliary F-N-R switch the proper sequence must be followed. See page 113 and 114 in this manual.

Push the switch forward to place the Transmission in Forward, Place the switch in the middle position to place the transmission in Neutral and Pull the switch rearward to put the Transmission in Reverse.

B. LOWER C. HOLD: The loader arms and bucket will not move when the control lever is in the HOLD position. When released, the control lever will automatically return to the HOLD position. You must manually move the control lever from the FLOAT position to the HOLD position.

D. RAISE E. DUMP

NOTE: See Transmission Operation / Initial Machine Movement for moving machine after engine start up.

F. ROLLBACK

3. KICKDOWN BUTTON (DOWNSHIFT TRANSMISSION) 77

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

INSTRUMENTS/CONTROLS

THREE SPOOL VALVE - TWO CONTROL LEVERS H

A

E

D

2

1

2 C

1

B

F

G 114/BS00B356

1. LIFT ARM CONTROL

AND

BUCKET

3

A. DUMP

TRIM THIS EDGE

4

B. ROLLBACK C. HOLD: The loader arms and bucket will not move when the control lever is in the HOLD position. When released, the control lever will automatically return to the HOLD position. You must manually move the control lever from the FLOAT position to the HOLD position

3. KICKDOWN BUTTON (DOWNSHIFT TRANSMISSION) 4. AUXILIARY F-N-R Switch:This switch will allow the operator to put t h e Tr a n s m i s s i o n i n For wa r d , Neutral or Reverse. To activate this auxiliary F-N-R switch the proper sequence must be followed. See page 113 and 114 in this manual.

Push the switch Forward to place the transmission in Forward, Place the switch in the middle position to place the transmission in Neutral and Pull the switch rearward to put the Transmission in Reverse.

D. FLOAT (Detent): This is a detent position. When in the FLOAT (Detent) position, the loader bucket can follow the level of the ground without movement of the control lever.

E. LOWER F. RAISE 2. AUXILARY CONTROL G. AUXILIARY FUNCTION

NOTE: See Transmission Operation / Initial Machine Movement for moving the machine after engine start up.

H. AUXILIARY FUNCTION

78

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

INSTRUMENTS/CONTROLS

Three Spool - Three Levers A 2

H

1

D

1 E

3 C

3

F 2

I

B

G 412/376629A1

1. BUCKET CONTROL A. DUMP C. HOLD: The loader arms and bucket will not move when the control lever is in the HOLD position. When released, the control lever will automatically return to the HOLD position. You must manually move the control lever from the FLOAT position to the HOLD position.

2. LIFT ARM CONTROL D. FLOAT (Detent): This is a detent position. When in the FLOAT (Detent) position, the loader bucket can follow the level of the ground without movement of the control lever.

E. LOWER F. HOLD: The loader arms and bucket will not move when the control lever is in the HOLD position. When released, the control lever will automatically return to the HOLD position. You must manually move the control lever from the FLOAT position to the HOLD position.

G. RAISE 3. AUXILIARY CONTROL H. AUXILIARY FUNCTION I. AUXILIARY FUNCTION

79

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

B. ROLLBACK

INSTRUMENTS/CONTROLS

Three Spool - Three Levers (continued) 4 A B 5

C

412

4. Kickdown Button (Downshift Transmission.

TRIM THIS EDGE

5. AUXILIARY F-N-R SWITCH: This switch will allow the operator to put the Transmission in Forward, Neutral or Reverse. To activate this auxiliary F-N-R switch the proper sequence must be followed. See page 113 and 114 in this manual. Push the switch Forward to place the Transmission in Forward, Place the switch in the middle position to place the Transmission in Neutral and Pull the switch rearward to put the Transmission in Reverse.

A. Forward (Transmission) B. Neutral (Transmission) C. Reverse (Transmission)

80

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

INSTRUMENTS/CONTROLS

Four Spool Valve - Three Levers A

D 2

G

I

E 3 2

1

3

C

1 B

H J

F 415/BS00N175

1. BUCKET AND CONTROL

LIFT

J. AUXILIARY FUNCTION

ARM

5

B. ROLLBACK C. HOLD: The loader arms and bucket will not move when the control lever is in the HOLD position. When released, the control lever will automatically return to the HOLD position. You must manually move the control lever from the FLOAT position to the HOLD position.

4

BD02N198

4. KICKDOWN BUTTON (DOWNSHIFT TRANSMISSION)

D. FLOAT (Detent): This is a detent position. When in the FLOAT (Detent) position, the loader bucket can follow the level of the ground without movement of the control lever.

5. AUXILIARY F-N-R SWITCH: This switch will allow the operator to put t h e Tr a n s m i s s i o n i n Fo r wa r d , Neutral or Reverse. To activate this auxiliary F-N-R switch the proper sequence must be followed. See page 113 and 114 in this manual.

Push the switch Forward to place the Transmission in Forward, Place the switch in the middle position to place the transmission in Neutral and Pull the switch rearward to put the Transmission in Reverse.

E. LOWER F. RAISE 2. AUXILIARY CONTROL G. AUXILIARY FUNCTION H. AUXILIARY FUNCTION 3. AUXILIARY CONTROL

NOTE: See Transmission Operation / Initial Machine Movement for moving the machine after engine start up.

I. AUXILIARY FUNCTION 81

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

A. DUMP

INSTRUMENTS/CONTROLS

SIDE CONSOLE

1 3

4

2

TRIM THIS EDGE

BD02N210

1. WRIST REST: Adjust the wrist rest to a comfortable height to operate the loader control levers.

2. ADJUSTMENT KNOB: To adjust, loosen the adjustment knob and raise or lower the wrist rest to the correct height. Tighten the knob.

BC00B128

3. HEAT CONTROL (IF EQUIPPED); Turn the control clockwise for ON. Adjust the control to the needed temperature. Turn the control completely counterclockwise for OFF (see Recirculation Louvers in this manual). Select the desired fan speed.

NOTE: Make sure the water inlet on the engine for the heater is in the full ON position.

BC00B127

4. BLOWER FAN SWITCH (IF EQUIPPED): The blower fan switch has four positions: OFF, 1, 2 and 3. Turn the switch to 3 for maximum speed and to 1 for the slowest speed. Turn the switch completely counterclockwise for OFF (see Recirculation Louvers in this manual).

82

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

INSTRUMENTS/CONTROLS

SIDE CONSOLE

BD02N189

5. WIPER/WASHER SWITCH (IF EQUIPPED): T h e w ip e r /wa s he r swi t ch ha s fi ve positions.

D C

A.OFF - Turn the switch completely counterclockwise for OFF. B.INTERMITTENT - Rotate the switch c l o ck w i s e t o t h e f i r s t p o s i t i o n fo r intermittent wiper speed.

B

C.LOW - Rotate the switch clockwise to the second position for low wiper speed.

A

E BC00B131

D.HIGH - Rotate the switch clockwise to the third position for high wiper speed.

E.WASH - Push down on the switch for washer fluid.

83

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

5

INSTRUMENTS/CONTROLS

SIDE CONSOLE

6

TRIM THIS EDGE

BD02N189

6. LAMP SWITCH: The lamp switch has five positions: A.OFF - Turn the switch completely counterclockwise for OFF.

E

B.PARK - Turn the switch to this position to illuminate the marker and tail lamps.

D

C.DRIVE - Turn the switch to this position to illuminate the console lamps, driving lamps, marker lamps and tail lamps.

C B

A BC00B133

D.ALL - Turn the switch to this position to illuminate the console lamps, driving lamps and flood lamps.

E. WORK - Turn the switch to this position to illuminate the console lamps and flood lamps.

84

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

INSTRUMENTS/CONTROLS

SIDE CONSOLE

8

9

10

BS02N189

BS98M034

7. AIR CONDITIONING TEMPERATURE CONTROL (IF EQUIPPED): Turn the control clockwise for ON. Adjust the control to the needed temperature. Turn the control counterclockwise for OFF (see Recirculation Louvers in this manual). Select desired the fan speed.

NOTE: For maximum cooling make sure the water inlet on the engine for the heater is in the full OFF position.

BC00B098

BC00B097

BC00B086

8. DECLUTCH SWITCH: The Declutch disengages the transmission when maximum power is needed for the loader. Push down on the top of the declutch switch and push on the brake pedal to operate the machine with the declutch.

9. DETENT ON/OFF SWITCH: The Detent On/Off switch is used to engage all detents. Push down on the top of the detent on/off switch to engage lift ar m and attachment roll back detents. Push the bottom of the switch for the OFF position.

10. RETURN-TO-TRAVEL SWITCH: The Return-To-Travel switch is used to automatically return the loader bucket to the travel position after you have dumped the loader bucket.

Push down on the top of the Return-To-Travel switch to engage the return to travel detent. Push the bottom of the switch for the Float Detent position.

85

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

7

INSTRUMENTS/CONTROLS

SIDE CONSOLE

12

11

13 BD02N189

TRIM THIS EDGE

BC00B081

11. AUTOSHIFT SWITCH: The autoshift switch is used to select the automatic or manual mode of operation for the transmission. When the autoshift switch is in the ON position the transmission will automatically shift UP and DOWN between 1st or 2nd and the highest speed setting on the transmission lever (see Transmission Operation in this manual for complete

operation).

12. RIDE CONTROL SWITCH: (If equipped) Push on the top of the function switch for the ON position. Ride Control can be left ON at all times, whether loading or roading. In the on position ride control will automatically activate when ground speed BC00B094 is above 5 km per hour (3.1 mph) and automatically shut off when ground speed is below 5 km per hour (3.1 mph). The indicator light on the lower half of the switch will illuminate when ride control is activated.To turn Ride Control OFF, push on the bottom of the function switch for the OFF position.

BC00B083

13. REAR WIPER/WASHER SWITCH (IF EQUIPPED): The rear wiper/washer switch has three positions. OFF - The switch is completely off when the bottom of the switch is pushed down.

ON - Push down on the top of the switch for the ON position WASH - Push down on the top of the switch and hold, washer fluid will continue to flow as long as the switch is held down.

86

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

INSTRUMENTS/CONTROLS

SIDE CONSOLE

14 14. ROTATING BEACON SWITCH (IF EQUIPPED): Push the top of the rotating beacon switch for the ON position and push the bottom of the switch for the OFF position.

BS98M034

87

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

BD02N189

INSTRUMENTS/CONTROLS

SIDE CONSOLE

15

BD03A070

15. COUPLER PIN ENGAGE SWITCH:

TRIM THIS EDGE

Slide the locking plate towards the center of the switch, push down on the top of the switch to RETRACT the pins. The switch lamp will illuminate when the pins are retracted. The switch will lock in the PIN BC00B099 EXTENDED position after the bottom of the switch has been pressed and the PINS EXTENDED.

16

BD02N189

16. FAN REVERSER SWITCH (IF equipped) To use the fan reverser let the machine idle in neutral. Depress the fan reverser switch and depress the throttle to high idle for a minimum of 10 seconds or until debris stops blowing out of the coolers. Return the machine to an idle and then release the fan reverser switch.

88

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

INSTRUMENTS/CONTROLS

BD02N189

17. F-N-R Switch (If equipped) Enable the auxiliary F-N-R switch by pushing down on the top of the enable switch. The indicator light on the bottom of the enable switch will illuminate when activated. By following the correct sequence and enabling the auxiliary F-N-R the operator may select FORWARD-NEUTRAL-REVERSE from the LOADER CONTROL LEVER or the AUXILIARY F-N-R SWITCH. See pages 113 and 114 for a complete description of the F-N-R sequence.

89

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

17

INSTRUMENTS/CONTROLS

MASTER DISCONNECT SWITCH

BD03A001

BD03A002

2

1 TRIM THIS EDGE

BD02N146

The Master Disconnect Switch has two positions: ON and OFF. (1) The panel, located at the right rear hood position, may be locked. See the decal located on the inside of the panel.

BS00A018

ON - This position energizes the entire electrical system. When the master Disconnect switch is ON and the key switch is OFF, the following electrical components have power: dome lamp, horn, stop lamps, four-way flashers and the rotary light switch.

BS00A203

OFF - This position disconnects all power to the machine.

IMPORTANT: DO NOT use the master Disconnect Switch to stop the engine.

BS00A017

90

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

INSTRUMENTS/CONTROLS

HOOD SWITCH

BD02N147

BD03A018

1. Push up on the switch to raise the hood. The switch will remain in the up position for hands free opening.

If the machine has no power or the battery is too low for the hood switch to function:

BD02N148

2. To close the hood push down on the switch. The down position must be held to lower the hood.

WARNING: Keep hands clear of the hood as it closes to avoid injury.

BD03A045

WARNING: This procedure is not for starting the engine. Attempting to jump start the engine from this location may cause electrical and harness damage.

1. Connect the positive jumper cable to the Cab B+ junction post, located behind the right side cab access door.

2. Connect the negative cable to a proper ground. The hood may now be operated at the switch.

91

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

Keep all tools, service equipment and personnel clear as the hood comes down.

INSTRUMENTS/CONTROLS If the machine has power but the actuator is not functioning:

1. Park the machine on level ground, lower the bucket. Put the transmission in neutral, apply the parking brake. Shut the engine off.

2. Remove the two actuator mounting bolts at the left rear of the machine just in front of the battery compartment.

3. Lift and support the hood with suitable equipment.

BD03A229

Recirculation Air Louvers The recirculation air louvers are behind the operators seat next to the floor. When open, air is recirculated in the cab. To open the louvers turn the knob clockwise. To close the louvers turn the knob counterclockwise.

TRIM THIS EDGE

NOTE: Always have these louvers open for maximum cooling with the air conditioning or maximum heat with the heater.

1

2

BD00B005

1. Loosen and slide knob as required to open or close louvers.

2. Recirculation louvers (behind filter)

92

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

INSTRUMENTS/CONTROLS

MAIN AIR LOUVERS

1

3 3 BD01E137

3. LOWER FRONT MAIN LOUVERS

RD98K323

1. LEFT-HAND MAIN LOUVERS

TRIM THIS EDGE

The lower front louvers direct air flow back to the operator.

2

RD98K303

2. RIGHT-HAND MAIN LOUVERS

The louvers on the Right-Hand and Left-Hand side in front of the console direct air flow back to the operator.

93

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

INSTRUMENTS/CONTROLS

Defrost Air Louvers The upper louvers under the front windshield and the louver under the rear window direct the air flow to defrost the windows. To get maximum air flow on the windows, close all other louvers and turn the blower fan to the fastest speed.

6

If a fogging condition occurs make sure t h e r e c i r c u l a t i o n a i r l o u ve r s a r e C L O S E D. I f e q u i p p e d w i t h A i r Conditioning, turn the Air Conditioning ON and turn the Heat Control completely clockwise.

RD98K323

6. LEFT-HAND DEFROST LOUVERS

TRIM THIS EDGE

4 4

BD01E137

4. LOWER DEFROST LOUVERS

5

RD98K303

5. RIGHT-HAND DEFROST LOUVERS

94

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

INSTRUMENTS/CONTROLS

Radio (If Equipped)

Window Latch

1

RD97F215

RD98K301

TRIM THIS EDGE

1. LIFT TO OPEN

A radio (if equipped) is available for this machine from your dealer. Refer to the radio manufacturers instructions for correct operation.

Door Latch 1

2 1 RD98K302

1. LATCH PIN 2. HOLD LATCH

The window can be kept partially open by lifting the Hold Latch and sliding it back on the Latch Pin until the Hold Latch locks in the Latch Pin.

RD97F218

1. PUSH TO OPEN DOOR

The window may be opened and locked against the side of the cab. To do this pull the hold latch toward the rear of the cab when the window is partially open.

This will unlatch the window and allow the window to swing back against the cab and lock.

To release the window from the full open position, pull on the window release in the right hand rear corner of the cab.

95

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

INSTRUMENTS/CONTROLS

Window Retainer Latch 1

RD97F173

1. PULL TO RELEASE WINDOW

OPERATORS SEAT TRIM THIS EDGE

Standard Seat

1

3

2

2 RD98K266

3. RECLINER ADJUSTMENT HANDLE: Lift up on the handle, move the b ack r es t t o t he d es i r e d p os i t i on , release the handle to lock the backrest in position.

RD98K267

1. LUMBAR ADJUSTMENT KNOB: Turn the knob clockwise to increase the lumbar suppor t, tur n the knob counterclockwise to decrease the lumbar support.

2. ARMREST HEIGHT CONTROL ADJUSTMENT: Turn the knob to raise or lower the armrest to the desired position.

NOTE: Each armrest will pivot to the up position.

96

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

INSTRUMENTS/CONTROLS

Optional Air Ride Seat

4 1 2

5

6 2 RD98K266

4. SLIDE ADJUSTMENT LEVER: Pull this lever up and adjust the seat for wa r d o r r ea r war d as r e qu i r ed .

Release the lever to lock the seat in position.

5. WEIGHT ADJUSTMENT KNOB: To adjust the seat for your weight you must pull the release lever out of the knob, Use the release lever to turn the knob clockwise to increase the weight resistance.

Tu r n the knob counterclockwise to decrease the weight resistance.

2. ARMREST HEIGHT CONTROL ADJUSTMENT: Turn the knob to raise or lower the armrest to the desired position.

NOTE: Each armrest will pivot to the up position.

6. HEIGHT ADJUSTMENT, STANDARD SEAT: Lift the seat all the way up, drop the seat to the lowest position. Lift the seat to the desired position. The seat will lock into accepted positions.

3

RD98K268

3. RECLINER ADJUSTMENT HANDLE: Lift up on the handle, move the ba ck r e s t t o t he de s i r e d p os i t io n , release the handle to lock the backrest in position.

97

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

RD98K267

1. LUMBAR ADJUSTMENT KNOB: Turn the knob clockwise to increase the lumbar suppor t, tur n the knob counterclockwise to decrease the lumbar support.

INSTRUMENTS/CONTROLS B. (Manual Adjustment): The seat can be raised or lowered by increasing or decreasing the air pressure in the seat. Lift the handle UP to increase the air pressure. Push the handle D OW N t o d e c r e a s e t h e a i r pressure and lower the seat.

5 4 RD98K268

TRIM THIS EDGE

4. SLIDE ADJUSTMENT LEVER: Pull this lever up and adjust the seat for wa r d o r r ea r wa r d as r e qu i r ed .

Release the lever to lock the seat in position.

6 7

NOTE: When adjusting the seat height for the first time or for a different operator. Sit in the operators seat, lift up momentarily on the height adjustment handle. The seat will automatically adjust to the operators weight. See height adjustment handle for final adjustments.

RD98K268

6. SEAT DEPTH HANDLE: Lift handle up and move the cushion to the desired position. Release the handle to lock the cushion in position.

7. SEAT CUSHION ANGLE ADJUSTMENT HANDLE: Lift up on the handle. Move the seat to the desired angle. Release the handle to lock the cushion angle.

5. HEIGHT ADJUSTMENT HANDLE: A. (Automatic Adjustment): With the operator sitting in the seat.

Lift the handle UP and release.

T h e s e a t w i l l a ut o m a ti c a l l y adjust UP and then bleed off air pressure to the optimum air pressure for the weight of the operator.

98

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

INSTRUMENTS/CONTROLS

5

8. DAMPENING ADJUSTMENT LEVER: The dampening adjustment lever has four positions from soft to hard. The first adjustment is with the small end of the adjustment lever pointing toward the front of the seat, as shown. The other three adjustments can be obtained by rotating the small end of the adjustment lever out away from the seat. Each of the adjustments has a slight detent. The suspension can be adjusted to var ious operating conditions.

8

RD00B010

TRIM THIS EDGE

SEAT BELT

RD97F225

RD97F225

1. Pull belt from holder. Fasten the belt end into the right-hand buckle.

2. To release the seat belt, push the red button on the buckle.

NOTE: Make sure the belt end and buckle are securely fastened. Do not pull out the right-hand buckle.

WARNING: Securely fasten your seat belt. Your machine is equipped with a ROPS cab or ROPS canopy for your protection. The seat belt can help insure your safety if it is used and maintained. Never wear a seat belt loosely or with slack in the belt system. Never wear the belt in a twisted condition or pinched between the seat structural members.

M437

99

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

INSTRUMENTS/CONTROLS

Inspection and Care 1. Keep sharp edges and items that can cause damage, away from the belts.

2. From time to time, check belts, buckles, retractors, tethers, slack take-up system and mounting bolts for damage.

3. Replace all parts that have damage or wear.

4. Replace belts that have cuts that can make the belt weak.

5. Check that bolts are tight on the seat bracket or mounting.

6. If belt is attached to seat make sure seat or seat brackets are mounted securely.

7. Keep seat belts clean and dry.

8. Clean belts only with a soap solution and warm water.

9. Do not use bleach or dye on the belts because this can make the belts weak.

Emergency Exit TRIM THIS EDGE

1 1

2

RD98K301

1. PIN 2. LATCH

BD03A042

1. EMERGENCY EXIT

Lift and pull the latch out of the pin.

Push the Right hand window open.

100

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

OPERATING INSTRUCTIONS BEFORE STARTING THE ENGINE 1. Do a daily walk around, visual inspection of the machine. Check for such items as hoses rubbing against other components, oil leaks, debris or trash buildup, loose bolts, damaged, or missing parts that would effect the normal and safe operation of the machine.

Make any necessary corrections before operating the machine.

3. Check that the machine fuel tank is filled with clean fuel that has the specification given in this manual.

WARNING: DO NOT operate the machine while under the influence of alcohol or drugs.

CM112

RUN - IN PROCEDURE It is impor tant that the run-in i n s t r u c t i o n s fo r a n ew e n g i n e b e followed. Proper run-in will increase engine power and service life. If the engine is not run-in properly, the piston rings and cylinder bore can be damaged.

2. Operate the machine with normal loads as much as possible.

3. Monitor the engine instruments frequently during operation.

Reduce throttle and/or load if the coolant temperature exceeds safe operating limits.

During the first 100 hours of operation, operate the machine as follows: 1. Do not run the engine at idle speed for long periods of time.

99

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE (First)

TRIM THIS EDGE

!

2. See the Maintenance Chart in this manual and do the items in the 10 Hour section.

OPERATING INSTRUCTIONS

First Service Intervals The following items are to be done during the Run-In Period and are in addition to the items in the Lubrications/Maintenance Charts in this manual.

AFTER FIRST 100 HOURS OF OPERATION Have your dealer do the After Delivery Check .......................... See After Delivery Check in this manual AFTER FIRST 100 HOURS OF OPERATION Change the front and rear axle differential and planetary oil when the axles are new or repaired ................... See Axle Planetary in this manual Change the transmission oil and filter when the transmission is new or repaired ........................... See Transmission Specifications in this manual Check all hose clamps, tighten as required.

TRIM THIS EDGE

SEAT BELT Always securely fasten your seat belt before operating the machine. From time to time, carefully inspect the seat belts for worn areas and replace belts when needed.

!

WARNING: Securely fasten your seat belt. Your machine is equipped with a ROPS cab or canopy for your protection. The seat belt can help insure your safety if it is used correctly and maintained. Never wear a seat belt loosely or with slack in the belt system. Never wear the seat belt in a twisted condition.

SA121

100

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

OPERATING INSTRUCTIONS

STARTING THE ENGINE

!

WARNING: Before you start the engine, always sit in the operators seat, fasten the seat belt, apply the parking brake, and make sure the transmission direction control and digging control (if equipped) is in NEUTRAL. Give a warning to all persons around you that you are starting the engine.

SC037

2. Adjust the seat and fasten your seat belt. Make sure you can push the foot pedals completely down with your back against the seat cushion.

3. Make sure the transmission direction control is in NEUTRAL and the parking brake is applied.

NOTE: If the engine starts and then stops, do not engage the starter motor again until the starter motor stops turning. DO NOT operate the starter motor more than 30 seconds at one time. Let the starter motor cool for at least two minutes before you actuate the starter motor again.

4. Turn the key switch to the ON position and check the instrument cluster. Monitor the engine grid heater indicator. Do not turn the engine over until the grid heater indicator lamp is off.

NOTE: If the weather is cold, below 10° C (50° F) See Operating in Cold Weather in this manual on pages 130131.

6. After the engine starts, check the in st r ume nts to make s ur e th e indications are correct. Run the engine at approximately 1200 RPM with the transmission in neutral until the engine coolant temperature is warm.

NOTE: Operate the machine at reduced loads until all systems reach operating temperature. This is very important during extremely cold weather operation to protect both the engine and hydraulic systems. See Operating in Cold Weather in this manual on pages130-131.

101

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

5. Turn the key switch to the START position until the engine star ts, then release the key.

1. Turn the master disconnect switch to The ON position.

OPERATING INSTRUCTIONS

Engine Speed Do not operate the engine at idle speed for long periods. This can cause a low operating temperature. A low operating temperature can cause acids and deposits in the engine oil.

Always bring the engine to low idle for a few minutes to let all parts cool evenly before shut down.

Always shut the engine down from the lowest idle to prevent damage to the turbocharger.

Run the engine at low idle for a minute at start up before picking up speed and load.

STOPPING THE ENGINE AND PARKING THE MACHINE

!

WARNING: Jumping on or off the machine can cause an injury. Always face the machine, use the hand rails and steps, and get on or off the machine slowly.

TRIM THIS EDGE

SA038

1. Before you leave the machine, make sure the machine is parked on level ground. The machine must be on level ground before you do scheduled maintenance.

IMPORTANT: If you must temporarily park the machine on a hillside, put the front of the machine toward the bottom of the hill. Make sure the machine is behind an object that will not move.

4. Run the engine at idle speed for three to five minutes to decrease the temperature of the engine and turbocharger.

NOTE: Do not turn the engine off at anything other than low idle to prevent damage to the turbocharger.

5. Turn the key switch to the OFF position and remove the key.

2. Lower the loader to the ground.

6. If your machine has a cab, lock the cab door.

3. Shift the transmission direction control to NEUTRAL and apply the parking brake.

7. Turn the master disconnect switch to the OFF position.

102

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

OPERATING INSTRUCTIONS

Engine Coolant Heater (If Equipped) The left side of the engine cylinder block has a passage for installing a coolant heater. See your dealer for this optional heater. Follow the heater m a n u fa c t u r e r s i n s t r u c t i o n s fo r installation.

BD03A003

TRIM THIS EDGE

Engine Grid Heater

BD02N191

The machine is equipped with an engine grid heater for cold weather operation.

Turn the ignition switch to ON and wait for the indicator lamp to go out. The engine should be turned over only after the lamp goes out.

The indicator light may come on again during cranking and shortly after the engine starts for post heating of the air.

T h i s a l l o w s fo r s m o o t h r u n n i n g conditions during cold weather warm up.

WARNING: Ether is not to be used.

103

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

OPERATING INSTRUCTIONS

Booster Battery Connections to Machine Batteries (Jump Start)

!

WARNING: Batteries contain acid and explosive gas. Explosion can result from sparks, flames or wrong cable connections. To connect the jumper cables correctly to the battery of this machine, see the correct method shown on this page. Failure to follow these instructions can cause serious injury or death.

SA006

!

WARNING: Battery explosion and/or damage to electrical components can result from improper connection of booster batteries or charger.

Connect positive to positive and negative to negative. Externally, battery acid can cause burns and blindness, and taken internally it is poison.

M146B

Two persons are required for this procedure. Make sure the person making the connections is wearing face protection.

TRIM THIS EDGE

IMPORTANT: The machine may only be Jump Started from the LEFT side of the machine.

NOTE: Make sure the batteries are not frozen. Do not use batteries that have been frozen. Replace the batteries if the batteries have been frozen.

1. Open the rear hood. Sit in the operators seat and have the other person make the connections.

2. If using jumper batteries, make sure the jumper batteries are 24 volts.

3. If using another machine for power, make sure the two machines, DO NOT touch.

4. Connect the positive (+) jumper cable to the positive (+) battery terminals first.

5. Connect the negative (-) jumper cable to the negative (-) terminal on the jumper batteries or the other machine. Connect the other end of the negative (-) jumper cable to a good frame ground away from the batteries.

6. Start the engine according to the instructions in this manual. See Starting the Engine in this manual.

7. Have the other person disconnect the jumper cables in the reverse order that the jumper cables were connected in. Close the rear hood.

104

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

OPERATING INSTRUCTIONS

1

1

2 BD02N165

BD02N162

2. STANDARD BATTERY

TRIM THIS EDGE

1. REMOVE TWO BOLTS TO ACCESS BATTERY (ONE EACH SIDE)

1

BS03A158

IMPORTANT: The machine may only be JUMP STARTED from the LEFT side.

105

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

OPERATING INSTRUCTIONS

BEFORE YOU OPERATE

!

WARNING: Before each period of operation, check the machine for correct operation of the steering, brakes, hydraulic controls, instruments, and safety equipment. Check the NEUTRAL position of the transmission control lever. A machine that runs correctly can prevent accidents. Make all necessary repairs or adjustments before you operate the machine.

SA040

Before You Operate the Machine Before you operate the machine each day or before shift test the machine for correct operation.

1. Have the machine in a clear level area and make sure all persons are clear of your machine.

2. Adjust the seat so that you can apply the foot brakes when your back is against the seat backrest.

TRIM THIS EDGE

3. Fasten and adjust the seat belt.

4. With the engine running and at operating temperature, check the instrument panel for correct indications.

5. Check the loader controls for correct operation.

6. Periodically test the parking brake neutral interlock function: A. Apply the parking brake by pushing down on the left side of the switch.

B. Enable the pilot control levers by pushing down on the right side of the switch.

C. Push down and hold your foot against the brake pedal.

D. Raise the loader bucket above the ground.

E. Shift the transmission into first gear forward.

F. The warning buzzer will sound.

G. Take your foot off the brake pedal.

H. Increase the engine speed to 1/2 throttle. The machine must not move. If the machine moves, see the service manual or see your authorized dealer and correct the problem. When the par king brake is applied, the transmission is automatically shifted into Neutral.

106

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

OPERATING INSTRUCTIONS 7. Test the parking brakes at a maximum of 250 hour intervals: A. Ensure that the declutch switch is in the off position.

B. Apply the parking brake by pushing down on the top of the switch.

C. Shift the transmission into 3rd gear NEUTRAL. D. Press the program switch.

E. Press the up count switch until the Display Center reads 011.

F. Return the program/reset switch to the off (center) position.

G. Press the up count switch until the 01 is shown in the Display Center.

H. Push down and hold your foot against the brake pedal.

I. Enable the pilot control levers by pushing down on the right hand side of the pilot control switch.

J. Raise the loader bucket above the ground.

L. Shift the transmission to REVERSE and increase the engine speed to full throttle. The machine must not move. If the machine does move, see the service manual or see your dealer and correct the problem.

M.Shift the transmission to the NEUTRAL position.

N. Press the reset switch momentarily to return to normal operation.

!

WARNING: DO NOT operate the machine while under the influence of alcohol or drugs.

CM112

!

WARNING: Never operate the engine in a closed building. Proper ventilation is required under all circumstances.

M142A

!

WARNING: Operate the machine with the door closed to provide proper ROPS protection and to properly utilize the heating, ventilating or cooling systems.

M122B

!

WARNING: Hillside operations can be dangerous. Rain, snow, ice, loose gravel, soft ground, etc., change the ground conditions. You must make a judgment if your machine can be safely operated on any hillside or ramp.

SB013

8. Release the parking brake.

9. Test the foot brakes for correct operation at a maximum of 250 hour intervals.

A. Push down and hold your foot against the brake pedal.

107

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

K. Shift the transmission to FORWARD and increase the engine speed to full throttle. The machine must not move. If the machine does move, see the service manual or see your dealer and correct the problem.

OPERATING INSTRUCTIONS B. Raise the loader bucket just above the ground.

C. Place the transmission in the manual mode.

D. Shift the transmission into 2nd gear forward.

E. Release the parking brake.

F. Increase the engine speed to full throttle. the machine must not move. If the machine does move, decrease engine speed to low idle. See your Service manual or your dealer for repairs.

G. Reset the parking brake.

10. Test the secondary steering at a maximum of 250 hour intervals. (See Secondary Steering Check in Maintenance and Adjustments in this manual.

TRIM THIS EDGE 108

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

OPERATING INSTRUCTIONS

MACHINE OPERATION Transmission Operation The transmission in this machine has four (4) forward speeds and three reverse speeds. Always select the correct speed for the job. If you have frequent stalls (engine running at full throttle and the wheels not turning) select a lower gear.

The transmission can be operated in Automatic or Manual mode.

The foot brake must be actuated while engaging the transmission to release the parking brake.

Initial Machine Movement / Parking Brake Release 1. Press the bottom of the parking brake switch.

2. Shift the transmission controller into forward or reverse.

4. Depress the foot throttle and the machine will move.

Manual Mode Operation To put the transmission in the Manual mode press the bottom of the Autoshift switch.

Up-Shifts Manual Mode You can shift the transmission from a lower gear to a higher gear without reducing the machine speed or engine speed. If the gear to be selected is two (2) or more higher than the present gear, the transmission will automatically shift gears at 2.5 second intervals until the gear selected has been reached.

Down-Shifts Manual Mode The transmission can be shifted from 4th to 1st gear without reducing machine or engine speed. If 1st gear is to be selected from 3rd or 4th gear, the transmission will down shift to 2nd gear for approximately 1.2 seconds and then shift to 1st gear. For smooth operation and operator comfort, reduce engine speed before down shifts.

Down-Shift Button, Manual Mode The down-shift button is used to shift the transmission from 2nd gear to 1st. The transmission will shift back to 2nd gear if (1) the down-shift button is pressed again or (2) if the transmission control lever is moved to NEUTRAL and then to FORWARD or REVERSE.

109

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

3. Depress and release the foot brake.

OPERATING INSTRUCTIONS

Automatic Mode Operation To put the transmission in the automatic mode press the top of the Autoshift switch.

Shifting, Automatic Mode When the transmission is in the automatic mode, the transmission will start to move in 1st gear (when the machine is stopped) and automatically up-shift until the gear selected has been reached. The transmission will also down-shift automatically as the speed decreases.

Down-shift Button, Automatic Mode

TRIM THIS EDGE

The down-shift button (1) is used to shift down through the gears in single steps.

Each time the switch is pressed down the transmission will shift down one gear range until 1st gear is reached. Once the down-shift button has been pressed down the transmission is taken out of the automatic mode. The transmission will remain in the gear that was selected by the down-shift button. It will return to the automatic mode when (1) the transmission control lever gear changes, or (2) the transmission control lever is moved to NEUTRAL and then to FORWARD or to REVERSE.

1

1

BD03A077

DOWN-SHIFT BUTTON, JOYSTICK CONTROL

BC01E146

DOWN-SHIFT BUTTON, THREE LEVER CONTROLS

Shuttle Shifting (Direction change) Manual or Automatic It is not necessary to bring the machine to a complete stop when changing directions from forward to reverse or reverse to forward. For smooth operation and operator comfort, reduce engine speed before direction changes.

110

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

OPERATING INSTRUCTIONS

F-N-R Switch (If equipped)

1

1. Transmission controller is in neutral (left side).

2. F-N-R switch is in neutral (right side).

3. The engine must be running.

4. Machine is stationary.

5. Parking brake is released.

Depressing the F-N-R enable switch allows the transmission to be controlled by the auxiliary F-N-R switch. The indicator light on the bottom of the enable switch will illuminate when activated. See Note: If the column mounted transmission controller is moved from neutral, the engine is stopped or the parking brake is applied, the auxiliary F-N-R mode is deactivated and transmission control defaults back to the Transmission Control Lever.

NOTE: Within 8 seconds from depressing the F-N-R enable switch the following 3 actions must take place or the F-N-R enable switch must be reactivated.

1. The parking brake switch must be released.

2. The service brake must be stepped on.

3. The F-N-R switch must select F or R from the neutral position.

111

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

BD03A070

The F-N-R switch can be enabled after the following conditions have been met:

OPERATING INSTRUCTIONS

CONTROL LEVERS TWO SPOOL VALVE - ONE CONTROL LEVER 4

2

5

1

3

BS01E154

TRIM THIS EDGE

See Loader Function Switches in this manual for RETURN-TO-DIG, BUCKET HEIGHT CONTROL and RETURN-TO-TRAVEL/FLOAT switches.

1

4

2

3

B1119A88

1. DUMP BUCKET 3. RAISE LIFT ARMS 2. ROLLBACK BUCKET 4. LOWER LIFT ARMS 5. HOLD: THE LOADER ARMS AND BUCKET WILL NOT MOVE WHEN THE CONTROL LEVER IS IN HOLD. WHEN RELEASED, THE CONTROL LEVER WILL RETURN TO HOLD AUTOMATICALLY.

NOTE: This page shows the basic loader control lever positions. The Detent Switch for the loader functions is in the OFF position.

112

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

OPERATING INSTRUCTIONS

AUXILIARY F-N-R SWITCH FOR JOYSTICK CONTROL LEVER APPLICATIONS

A 1 B

3

C RD98K313 BD03A065

5. The Parking released (3).

1. AUXILIARY F-N-R SWITCH

Brake

must

be

A. FORWARD TRIM THIS EDGE

B. NEUTRAL C. REVERSE To actuate the Auxiliary F-N-R switch the following conditions MUST be met: 1. The machine must be stopped.

4

2. The engine must be running.

3. The Auxiliary F-N-R Switch (1) must be in Neutral (B).

BD01E113

When steps 1 through 5 have been met the Auxiliar y F-N-R Switch may be enabled by pushing down on the top of the switch (4). The indicator light on the bottom of the switch will illuminate.

2

The Auxiliar y F-N-R Switch will be DEACTIVATED and F-N-R control will de fa ul t b ack t o th e Tran s m is s i o n Control Lever if: RD98K322

4. The Transmission Control Lever (2) must be in neutral.

1. The engine is stopped.

2. The parking brake is applied.

3. The transmission control lever is taken out of the neutral position.

113

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

OPERATING INSTRUCTIONS

AUXILIARY F-N-R SWITCH WITH THREE SPOOL VALVE THREE LEVERS

A B 1

3 C RD98K313

BD03A067

5. The Parking released (3).

1. AUXILIARY F-N-R SWITCH

Brake

must

be

A. FORWARD

TRIM THIS EDGE

B. NEUTRAL C. REVERSE To actuate the Auxiliary F-N-R switch the following conditions MUST be met: 1. The machine must be stopped.

4

2. The engine must be running.

3. The Auxiliary F-N-R Switch (1) must be in Neutral (B).

BD03A069

When steps 1 through 5 have been met the Auxiliar y F-N-R Switch may be enabled by pushing down on the top of the switch (4). The indicator light on the bottom of the switch will illuminate.

2

The Auxiliary F-N-R control will default back to the Transmission Control Lever if: 1. The engine is stopped.

RD98K322

4. The Transmission Control Lever (2) must be in neutral.

2. The parking brake is applied.

3. The transmission control lever is taken out of the neutral position.

114

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

OPERATING INSTRUCTIONS

THREE SPOOL VALVE - TWO CONTROL LEVERS 3

2

1

5 4

NOTE: This page shows the basic control lever positions. The Detent Switch for the loader functions is in the OFF position.

6

See Loader Function Switches in this m a n u a l fo r R E T U R N - TO - D I G , BUCKET HEIGHT CONTRO L and R E T U R N - TO - T R AV E L / F L O AT switches.

7

1

3

2

4

TRIM THIS EDGE

BS01E143

B1119A88

1. DUMP BUCKET 3. LOWER LIFT ARMS 2. ROLLBACK BUCKET 4. RAISE LIFT ARMS 5. HOLD: THE LOADER ARMS AND BUCKET WILL NOT MOVE WHEN THE CONTROL LEVERS ARE IN HOLD. WHEN RELEASED, THE CONTROL LEVERS WILL RETURN TO HOLD AUTOMATICALLY. 6. 7.) AUXILIARY FUNCTION

115

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

OPERATING INSTRUCTIONS

THREE SPOOL VALVE - THREE CONTROL LEVERS NOTE: This page shows the basic loader control lever positions. The Detent Switch for the loader functions is in the OFF position.

3

1 6

5 5

5 7

2

See Loader Function Switches in this m a n u a l fo r R E T U R N - TO - D I G , BUCKET HEIGHT CONTRO L and R E T U R N - TO - T R AV E L / F L O AT switches.

4

BC01E146

TRIM THIS EDGE

1

3

2

4

B1119A88

1. DUMP BUCKET 3. LOWER LIFT ARMS 2. ROLLBACK BUCKET 4. RAISE LIFT ARMS 5. HOLD: THE LOADER ARMS AND BUCKET WILL NOT MOVE WHEN THE CONTROL LEVERS ARE IN HOLD. WHEN RELEASED, THE CONTROL LEVERS WILL RETURN TO HOLD AUTOMATICALLY. 6. 7.) AUXILIARY FUNCTION.

116

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

OPERATING INSTRUCTIONS

FOUR SPOOL VALVE - THREE CONTROL LEVERS 3

2

5

1

4

6

NOTE: This page shows the basic loader control lever positions. The Detent Switch is in the OFF position.

8

See Loader Function Switches in this m a n u a l fo r R E T U R N - TO - D I G , BUCKET HEIGHT CONTRO L and R E T U R N - TO - T R AV E L / F L O AT switches.

9 7

1

3

2

3

TRIM THIS EDGE

BS01E145

B1119A88

1. DUMP BUCKET 3. LOWER LIFT ARMS 2. ROLLBACK BUCKET 4. RAISE LIFT ARMS 5. HOLD: THE LOADER ARMS AND BUCKET WILL NOT MOVE WHEN THE CONTROL LEVERS ARE IN HOLD. WHEN RELEASED, THE CONTROL LEVERS WILL RETURN TO HOLD AUTOMATICALLY. 6-7.)

First Auxiliary Function 8-9.) Second Auxiliary Function

117

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

OPERATING INSTRUCTIONS

LOADER FUNCTION SWITCHES Push down on the top of the detent switch to engage all detents. Push on th e bot tom o f swi tc h for t he O FF position.

1

2 RD97F178

1. DETENT ON/OFF SWITCH 2. RETURN-TO-TRAVEL/ FLOAT SWITCH

Return-To-Dig TRIM THIS EDGE

The Return-To-Dig function is used to automatically return the loader bucket to the dig position after you have dumped the loader bucket. To enable the Return-ToDig function press the bottom of the Return-To-Travel/Float switch. (2)

2 1 1

BS01E154

BC01E146

1. FLOAT AND ROLLBACK DETENT

1. FLOAT 2. ROLLBACK DETENT

To actuate, move the control lever(s) into the FLOAT and ROLLBACK detents. The bucket control lever will automatically return to the HOLD position and the loader arm will remain in float when the loader reaches the Return-To-Dig position. See Loader Adjustments in this manual for Return-To-Dig Adjustment.

B1125A88J

118

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

OPERATING INSTRUCTIONS

Bucket Height Control The bucket height control is used to automatically stop the loader arms at the height that you select.

1

1

BS01E154

BC01E146

To actuate, move the control lever into the RAISE detent. The control lever(s) will automatically return to the HOLD position when the loader bucket reaches the height selected. See for Bucket Height Control Adjustments in this manual.

Return-To-Travel The Return-To-Travel function is used to automatically stop the loader bucket at the carry height that you select. To enable the Return-To-Travel function press the top of the return to Travel/Float switch.

1 1 2

BC01E146

1. ROLLBACK DETENT 2. FLOAT

BS01E154

1. FLOAT AND ROLLBACK DETENT

To actuate, move the control lever(s) into the FLOAT and ROLLBACK detents. The control lever(s) will automatically return to the HOLD position when the loader reaches the Return-To-Travel position. See for Return-To-Travel Adjustment in this manual.

119

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

1. RAISE

1. RAISE

OPERATING INSTRUCTIONS

Float The Float function is used to let the loader bucket float across rough ground.

B1128A88J

To actuate, move the control lever into the FLOAT detent. The control lever will remain in this position until manually removed. To enable this function press the bottom of the Return-To-Dig/Float switch.

TRIM THIS EDGE

1

1

BC01E143

1. Float

BS01E154

1. Float

LOADER CONTROL T h e l o a d e r c o n t r o l l ev e r s a r e connected to a hydraulic accumulator through a pressure reducing valve. The pur pose of the reducing valve and accumulator combination is to: (1) allow the operator to lower the loader arms if the engine stops with the loader arms raised, or (2) give the control system hydraulic pressure assistance when operating the machine at low idle s p e e d . To t e s t a c c u m u l a t o r performance, perform steps 1 through 5.

2. Raise the loader bucket.

3. Stop the engine.

4. Turn the key to RUN. 5. Move the lift arm control to LOWER. The loader bucket must lower to the ground. If the bucket does not lower to the ground, see t h e S e r v i c e M a n u a l fo r t h i s machine or see your dealer.

1. Start the engine.

120

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

OPERATING INSTRUCTIONS

BRAKE ACCUMULATORS Two hydraulic accumulators are connected in the brake system.The purpose of the accumulators is to provide the brake modulating valve with a positive supply of pressurized hydraulic fluid.

Test the accumulators for correct operation every 100 hours.

2. Run the engine at 1/2 throttle for 15 seconds.

3. Stop the engine.

4. Without starting the engine, turn the key to the ON position. After the instrument cluster completes the diagnostic check, confirm that the brake pressure light is not on.

5. Repeatedly pump the brake pedal until the brake pressure lamp is illuminated.

6. After the lamp illuminates, continue to pump the brake pedal and count the number of full applications.

If you can complete six (6) full brake applications after the indicator lamp illuminates, the accumulators are working correctly. If you can not complete six (6) applications, see the Service Manual for this machine or see your dealer.

DECLUTCH The Delutch function is used to allow the engine to increase speed and supply the loader with more hydraulic oil for greater loader power and faster control function. When the Declutch switch is in the ON position, and you push down on the brake pedal, the transmission is disengaged from the drive wheels. Release the brake pedal to engage the transmission power. If required, use the brake to stop the machine.

1

RD97F178

1. DECLUTCH SWITCH

121

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

1. Start the engine.

OPERATING INSTRUCTIONS

BUCKET LEVEL INDICATOR The bottom of the bucket is parallel with the ground when the flat portion of the bucket, (shown) is horizontal.

BD00N076

AUXILIARY HYDRAULIC CONNECTION (IF EQUIPPED) TRIM THIS EDGE

Your Wheel Loader is equipped with an Auxiliary Hydraulic System. A control lever on the console controls flow to the auxiliary hydraulic connection points on the lift arms.The auxiliary control lever (1) used with a joystick (2) is equipped with mechanical detents to lock it into full forward, full rearward and neutral positions.

Auxiliary control levers on non-joystick machines DO NOT have mechanical detents.

2

1 BD03A009

BD03A063

Auxiliary Hydraulic System Specifications 721D Wheel Loader (XT and Z-Bar Linkage) Maximum System Pressure ....................................................250 Bar (3 625 PSI) Maximum Capacity at 2 150 Engine RPM .......................... 184 L/min (48.6 GPM) NOTE: Maximum system pressure measured on the machine at the pump pressure port.

122

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

OPERATING INSTRUCTIONS

ROTATING BEACON (IF EQUIPPED) The rotating beacon control switch is on the RH console. Push the top of the switch for ON position and push the bottom of the switch for OFF position.

RD97K027

Ride Control is a feature that increases the ride comfort of the Wheel Loader over all types of terrain with either an empty or loaded bucket.

Ride Control will reduce Fore and Aft pitching motion during travel to allow faster speeds in load and carry applications for increased BC00B094 productivity and operator comfort. It will also reduce shock loads to the Wheel Loader for reduced tire flex, structural fatigue and vibration, resulting in longer component life and reduced costs.

The machine is equipped with speed dependent ride control. Push on the function switch symbol to activate. With ride control active, the green indicator light will illuminate anytime the machine is traveling faster than 5 km/h (3.1 mph) indicating that the ride control is functioning. Ride control will disengage automatically at slower speeds for loading and unloading.

Ride Control can be left ON at all times, whether loading or roading.

To turn Ride Control OFF, push on the bottom of function switch for the OFF position.

NOTE: Ride Control should be OFF when the bucket is used in fine grading operation or when precision placement of a load suspended from the bucket or other attachment is required.

123

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

RIDE CONTROL (IF EQUIPPED)

OPERATING INSTRUCTIONS

COUPLER PIN ENGAGEMENT (IF EQUIPPED) Use the factory/field installed coupler system to change attachments quickly. A control switch for the system is located on the RH console.

To connect an attachment, slide the locking tab upward and press the top of the COUPLER switch to RETRACT the PINS. The amber light will illuminate and the PINS will remain in the retracted position. Position the front coupler into the attachment. Press the bottom of the switch until it fully locks into place to EXTEND the PINS. Make sure the coupler pins are fully engaged to the attachment and the amber light is off before using the machine.

TRIM THIS EDGE BD03A070

To change attachments, lower the attachment to the ground, slide the locking tab upward and press the top of the COUPLER switch (PINS RETRACT). Back out of the attachment.

!

WARNING: Before using the machine make sure the attachment is securely connected to the machine by putting the front of the attachment against the ground and putting down pressure on the attachment.

M781

124

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

OPERATING INSTRUCTIONS

LOADER OPERATING TIPS This Wheel Loader, with standard equipment and authorized attachments, is intended to be used for above ground level digging and general earth moving purpose such as land leveling, truck loading, material rehandling and ditch cleaning. If the machine is to be used for lifting objects, make sure that the machine is properly equipped and follow the instructions and safety precautions in this manual.

Leveling Operation Always operate the machine in reverse when leveling the surface.

Pushing Operation 163L96

IMPORTANT: The bucket MUST NOT be in the FULL DUMP position during the pushing operation.

Scraping Operation When scraping hard or frozen surfaces the bucket must be level and flat to the surface. Operate the machine at a slow speed.

164L96

163L96

!

WARNING: Impact Hazard - Bucket edge or teeth can catch on frozen surface or buried object during surface scraping operations. Before operation inspect the area for objects the bucket can catch on and mark them. During operation make sure the bottom of the bucket is level with the surface to be scraped. Operate the machine around the objects and at slow speed. Injury to the operator and damage to the machine can result if these precautions are not followed.

M465

125

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

When pushing material do not set the bucket dumping angle more than 20 degrees.

OPERATING INSTRUCTIONS

Transport and Carry Operation The bucket must be in the roll back position and the bottom of the bucket must not be more than 305 to 457 mm (12 to 18 inches) off the surface.

165L96

!

WARNING: When you operate the machine, keep the loader bucket as low as possible. This low position gives better balance and permits you to see more clearly. If the bucket is full and you move the machine over ground that is rough or surfaces that can cause the machine to slide, always operate at slow speed. If you do not use this procedure, the machine can go out of control and roll-over.

SA041

TRIM THIS EDGE

Operating on a Hill

!

WARNING: Hillside operations can be dangerous. Rain, snow, ice loose gravel, soft ground, etc., change the ground conditions. You must make a judgment if your machine can be safely operated on any hillside or ramp.

SB013

Before you operate this machine on a hill, always put the transmission in a lower range and test the brakes. DO NOT let the machine move down a hill with the transmission in NEUTRAL. DO NOT use the Declutch Switch when operating on a hill.

126

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

OPERATING INSTRUCTIONS

TOWING THE MACHINE If your machine is disabled, you must make a judgment if the machine can be moved without further damage. If possible, repair the machine at the job location.

If you cannot repair the machine at the job location and if you have a transport trailer, park the trailer as close as possible to the machine (see Transporting the Machine in this manual).

NEVER TOW MACHINE FROM THE FRONT. 1. Attach a rigid drawbar to the machine.

2. If the machine cannot be started to release the parking brake, do the following: D. Turn the adjusting screw counterclockwise until the parking brake is released (3).

3. If the machine is to be towed more than 0.8 km (1/2 mile) you must disconnect the front and rear drive shafts.

4. Tow the disabled machine at a maximum speed of 8 km/h (5 mph).

1 BD03A036

B. Remove the Parking brake cover (1).

2

3 BD03A037

C. Loosen the lock nut (2).

127

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

A. Put blocks in front of and behind each tire.

OPERATING INSTRUCTIONS

TRANSPORTING THE MACHINE

!

WARNING: The machine can slip and fall from a trailer or ramp and cause injury or death. Make sure the trailer and ramp is not slippery. Remove all oil, grease, ice, etc. Carefully move the machine off or onto the trailer with the machine centered on the trailer and ramp.

SB042

!

WARNING: Before you put the machine on a trailer, remove all snow, ice, oil or grease from the trailer and ramp.

46-76C

!

WARNING: Know the rules, regulations, laws and safety equipment necessary for transporting or operating this machine on a road or highway.

Rotating beacon, backup alarm, slow moving vehicle emblem and other safety equipment items are available from your dealer.

84-13A

7. Turn the battery master disconnect switch to the OFF position.

TRIM THIS EDGE

You must know the rules or laws for transportation and safety that are used in each area that you will be in. Make sure that the truck and machine are e q u i p p e d wi t h t h e c o r r e c t s a fet y equipment.

8. Put blocks at the FRONT and REAR of each tire of the machine.

9. Use chains to fasten the machine to the trailer. See the Next Page for tie down locations of the machine.

1. Put a block at the front and rear of each trailer wheel.

2. Be Careful, move the machine SLOWLY onto the trailer.

3. Lower the loader bucket onto the trailer.

4. Put the Transport/Service link in the LOCKED position.

5. Apply the parking brake and stop the engine. Remove the key.

10. Put a cover over the exhaust pipe.

11. Rotate the beacon (if equipped) to the TRANSPORT position. See beacon in this manual. (if equipped) 12. Measure from the ground to the highest point of the machine. You must know the clearance height of the machine.

6. Make sure the transmission control is in the NEUTRAL position and loader controls are in the HOLD position.

128

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

OPERATING INSTRUCTIONS

Transporting the Machine on a Trailer Machine Tie Down Locations

BD01E126

BD00M030

TRANSPORT LOCK MUST BE SECURED.

TRIM THIS EDGE

CHAINS MUST BE SECURELY FASTENED TO THE FRONT TIE DOWN HOLE.

BD00B012 BD00M032

CHAINS MUST BE SECURELY FASTENED TO THE REAR TIE DOWN HOLE.

CHAINS MUST BE SECURELY FASTENED AROUND LOADER ARM.

FAR1069

CHAINS MUST BE SECURELY FASTENED AROUND LOADER ARM.

129

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

OPERATING INSTRUCTIONS

OPERATING IN COLD WEATHER Cold weather conditions cause special problems. During these conditions your machine will require special start up, and warm up, and maintenance procedures for the best performance. Proper cold weather maintenance will extend the service life of your machine.

1. BATTERIES/ELECTRICAL SYSTEM - Clean the batteries and make sure the batteries are at full charge.

NOTE: A fully charged battery at -17°C (0°F) has only 40 percent of the normal starting power. At -29°C (-20°F) the battery has only 18 percent of the power remaining.

TRIM THIS EDGE

Inspect the batter y cables and terminals. Clean the terminals and apply electrical terminal sealers ( s e e y o u r d e a l e r ) t o p r ev e n t corrosion.

If you add water to the batteries and the temperature is below 0°C (32°F),make sure you charge the batteries or r un the engine for approximately two (2) hours. This procedure will prevent batter y freezing (see Batteries and Booster Batter y Connections in this manual.

Inspect the batter y cables and terminals. Clean the terminals and apply electrical terminal sealer (see your dealer) to prevent corrosion.

2. LUBRICANTS - Make sure you follow the recommended oil and filter service for the engine and the hydraulic system as shown in this manual. Use the correct viscosity oil i n ea ch co mpon ent for th e ambient temperatures the machine is operated in (see Lubrication in this manual).

3. FUEL SYSTEM - Check with your fuel supplier for the correct cold weather fuel. Engine power will be reduced if wax particles are in the fuel filters.

Check for water in the fuel system.

Col d te mperatu re s can c aus e condensation to form in the fuel tank. Check the fuel filter for water.

4. COOLING SYSTEM - Check the coolant mixture before you operate in cold temperatures. A mixture of 50% ethy lene gly col and 50% water must be used in this machine. This mixture is used if the lowest ambient temperature is above -37°C (-34°F). If the ambient temperature is lower, adjust the mixture. It is recommended that ethylene glycol and water be used in your machine all year ( See Engine Cooling System in this manual).

5. COLD TEMPERATURE STARTING AIDS - This machine is equipped with an engine grid heater. Turn the key switch to ON and wait for the engine grid heater indicator lamp to go out. Contact your Dealer for additional Cold Weather starting aids. The indicator light may come on ag ain d ur in g cran ki ng an d shortly after the engine starts for post heating of the air. This allows for smooth r unning conditions during cold weather warm up.

130

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

OPERATING INSTRUCTIONS 6. MACHINE WARM-UP - Once the engine has started, run the engine at half throttle (1 100 to 1 300 RPM) for a minimum of 4 minutes under no load. This will help stabilize the engine.

IMPORTANT: DO NOT operate the machine on the road until the transmission oil and axle oil have been correctly warmed up. Operate the machine in a clear safe area before road operation.

ATTENTION: Make sure there is clearance around the machine before steering the machine from right to left.

In severe cold weather conditions the brakes response can be slow.

The use of correct oil in the hydraulic/brake system is required.

Even with the correct oil in the hydraulic/brake system the first few times the brakes are actuated there may be some delay before the brakes are applied. The operator must actuate the brake pedal a minimum of 8 to 10 times before the machine is moved.

7. If the machine has been left idling in cold temperature, the engine will stay warm. But the hydraulic/brake oil and the axle oil will not stay warm. The oil and components can become cold and slow brake function response time. If this s h o u l d h a p p e n yo u M U S T g o through the complete machine warm-up procedure.

8. The transmission is equipped with internal protection that does not allow the transmission to engage below -12°C (10°F). If the transmission does not engage below these temperatures, allow 2 to 4 minutes of running in neutral (this time will var y with temperature), then try again.

131

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

After engine warm-up, enable the pilot controls by pushing down on the right hand side of the switch on the instrument control panel. At this time, place the hydraulic lift arm into float and the bucket into roll back to load the engine and heat the hydraulic oil. Continue to heat the hydraulic oil until the 2nd. bar of the hydraulic oil temperature gauge is on. This will yield 20C (68°F).

This may take several minutes.

Apply and hold the foot brake, cycle the lift arm and bucket. Repeat the float/roll back heating procedure again until the 2nd. bar of the hydraulic oil temperature is on.

Raise the lift arms enough to steer the unit full left and right to warm the oil in the steering cylinders. In extreme cold conditions, hold the f l o at / r o l l b a ck c o n d i t i o n fo r 5 minutes maximum in time rather than to the second bar.

When the machine has been correctly warmed up, apply the foot brake and hold, shift the transmission to forward push the park brake to the Off position and release the foot brake. Operate the mac hi ne i n a c lear s afe a re a.

Check the full operation of the machine. DO NOT operate the machine in third or fourth gear until the transmission oil and axle oil have been war med up and the machine moves freely.

OPERATING INSTRUCTIONS

OPERATING IN HOT WEATHER To prevent damage to the machine, do the following:

4. Clean all dirt and debris from the cooling system and engine area.

1. Keep the coolant at the correct level in the radiator.

5. Check the condition of the drive belts.

2. Use the correct solution of ethylene glycol and water in the cooling system.

6. Use lubricants viscosity.

3. Test the radiator cap before hot weather starts. Replace the cap as required. See your dealer.

TRIM THIS EDGE 132

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

of

the

correct

WHEELS/TIRES/BALLAST WHEELS AND TIRES

!

WARNING: Exploding tires and/or rim parts can cause injury or death.

Keep yourself and others out of the DANGER AREA. Stand on the tread side of the tire. Always use the correct air pressure and follow the instructions in this manual for adding air or servicing the tires.

SD020

!

WARNING: Explosive separation of the tire and/or rim parts can cause injury or death. When tire service is necessary, have a qualified tire mechanic service the tire.

!

WARNING: DO NOT weld to wheel or rim when a tire is installed. Welding will cause an explosive air/gas mixture that will be ignited with high temperatures. This can happen to tires inflated or deflated. Removing air or breaking bead is not adequate. Tire MUST be completely removed from the rim prior to welding.

SB134

BALLAST It is the recommendation of the Case, LLC. NOT to add Ballast to the tires of your machine. Make sure tires are properly inflated. See the Tire Chart on page 137 of this manual.

133

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE (First)

TRIM THIS EDGE

84-113

WHEELS/TIRES/BALLAST

TRIM THIS EDGE B910410J

The above illustration show danger areas caused by exploding tires and/or rim parts. KEEP YOURSELF AND OTHERS OUT OF THESE DANGER AREAS. The next page shows the correct methods that you MUST use when adding air or servicing a tire.

134

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

WHEELS/TIRES/BALLAST

Adding Air to the Tires

4. Inflate the tire to the recommended air pressure. DO NOT inflate the tire more than the recommended pressure given on the following page.

This procedure is only for adding air to the tire. If the tire has lost most or all of the air, do the following.

Tire or Rim Service Always have a qualified tire mechanic ser vice the tires and r ims for this machine. It is recommended that you have this mechanic inflate the tires. To prevent accidents, use a restraining device (tire inflation cage), correct equipment, and correct procedure.

Explosive separation of the tire (single piece rim) or the tire and/or rim parts (multi-piece rim) can cause serious injury or death.

Tire Tread Direction

B790490R

When the tire is installed on the wheel make sur e the tire tread is in the direction shown.

2. Use an air hose with remote shutoff valve and a self-locking air chuck.

3. Stand BEHIND the tread of the tire and make sure ALL persons are away fr om the side of the tir e before you start to add air.

FORWARD

B770164R

BD03A024

135

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

1. Before you add air, have the wheel correctly installed on the machine or put the wheel in a restraining device (tire inflation cage).

WHEELS/TIRES/BALLAST

Wheel Bolt Torque Check the torque of the wheel bolts after every 20 hours of operation until the wheel bolts stay tight, if the machine is new or if a wheel has been removed and installed.

If a wheel is removed from the machine and installed, tighten the bolts using the sequence shown. First tighten the bolts to 298 Nm (220 pound-feet), then to a final torque of 640 to 720 Nm (475 to 530 pound-feet) in the same sequence.

Bolts are M22 - 1.5, GR. 10.9

1 10

8 12

6

3

4

TRIM THIS EDGE

11

5 7

2

9

BD03A027 B0987A88

721D

136

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

WHEELS/TIRES/BALLAST

Tire Pressure Chart TREAD

SIZE

TYPE

kPa

(PSI)

(bar)

L2

345

50

3.45

275

40

2.75

345

50

3.45

275

40

2.75

20.5 X 25

Front Rear

20.5 X 25

Front

L3

Rear 20.5R X 25

Front

TIRE PRESSURE

XTLA TL*

Rear 20.5R X 25

Front

XHA TL*

345

Rear 20.5 X 25

Front

GP2B

345

Front

RT3B

Front

*VUT

Rear 20.5R X 25

Front

*VMT

Rear

3.45

50

3.45

40

2.75

345

50

3.45

275

40

2.75

345

345

50

3.45

275

40

2.75

TRIM THIS EDGE

RIGHT PAGE

3.45 2.75

2.75

137

Bur 6-35092na

50 40 50

Rear 20.5R X 25

3.45 2.75

40

Rear 20.5 X 25

50 40

TRIM THIS EDGE

TIRE

WHEELS/TIRES/BALLAST

NOTES

TRIM THIS EDGE 138

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

LUBRICATION/FILTERS/FLUIDS

LUBRICATION/FILTERS/FLUIDS GENERAL SAFETY BEFORE YOU SERVICE WARNING: Improper service or repair can cause injury or death. If you do not understand the service procedures for this machine, see your dealer or the service manual for this machine.

SC021

WARNING: Raised equipment on the machine without an operator can cause injury or death. Before you leave the operators compartment, always support or lower the equipment (backhoe, blade, boom, bucket, etc.) to the ground and stop the engine.

SA044

Use the correct safety clothing and safety equipment. Understand how to use a fire extinguisher and first aid kit.

TRIM THIS EDGE

Read the safety decals and information decals on the machine. Read the operators manual and safety manual.

Understand the operation of the machine before you start servicing

B770996R

B801147T

Before you service the machine, put a Do Not Operate tag on the instrument panel. One Do Not Operate tag is included with your machine. Additional tags are available from your dealer.

321-4614

139

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

LUBRICATION/FILTERS/FLUIDS

SUPPORT STRUT FOR LOADER LIFT ARMS WARNING: If you service the machine with the loader lift arms raised, always use the support strut.

1. Empty the loader bucket, raise the loader lift arms to approximately 2.1 m (7 ft) and stop the engine.

2. Remove the support strut from the transport position by removing the retaining bolt.(1) 3. Place the support strut onto the cylinder rod with guide lock tab on top of cylinder and pointing toward the bucket. (2) 3. Install the retaining bolt entirely into the support strut using all threads. (3) NOTE: Use spacer as shown (4) 4. Slowly lower the lift arms onto the support strut.

If you do not follow this procedure, you can cause death or serious injury if the loader lift arms are lowered by accident.

M824

TRIM THIS EDGE

2 2

3

1

BD01E127

BD02N201

SUPPORT STRUT IN TRANSPORT POSITION

SUPPORT STRUT IN SERVICE POSITION

4

BD02N200

140

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

LUBRICATION/FILTERS/FLUIDS

TRANSPORT/SERVICE LINK WARNING: Keep clear of this area when engine is running. Machine could pivot unless the transport and service link is in its LOCKED position.

After servicing is completed, unlock the transport and service link and secure in place on the rear frame pivot.

SA069

BD03A040

STRAIGHT AHEAD LOCKED POSITION

BD03A041

OPERATING POSITION

After servicing and before you move the machine, return the Transport/Service link in the OPERATING position.

ENVIRONMENT Before you service this machine and before you dispose of the old fluids and lubricants, always remember the environment. DO NOT put oil or fluids into the ground or into containers that can leak.

Check with your local environmental or recycling center or your dealer for correct disposal information.

141

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

Before you transport or service this machine, always put the Transport/Service link in the LOCKED position.

LUBRICATION/FILTERS/FLUIDS

SYSTEMGARD LUBRICATION ANALYSIS PROGRAM Ask your dealer about our lubricant analysis program, Systemgard. Through this service, your lubricants are tested in an independent laboratory. You simply remove a sample of lubricant from your machine and send the sample to the independent Systemgard laboratory. After the sample is processed, the laboratory will report back to you and guide you with maintenance requirements. Systemgard can help support your equipment up time and provide you with a service that can pay back dividends when you trade for another piece of Case equipment.

TRIM THIS EDGE B830752T

PLASTIC AND RESIN PARTS Avoid using gasoline, kerosene, paint thinner, etc., when cleaning plastic windows, console, instrument cluster, monitor, gauges, etc. Use ONLY water, mild soap and a soft cloth when you clean these parts.

Using gasoline, kerosene, thinners, etc., will cause discoloration, cracking or deformation of the part being cleaned.

142

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

LUBRICATION/FILTERS/FLUIDS

THE ENGINE HOOD

1

1. Push up on the switch to raise the hood. The switch will remain in the up position for hands free opening.

The Hood may be stopped during this procedure by retur ning the sw i t c h t o t h e c e n t e r o r O F F position.

BD02N148

2. To close the hood push down on the switch. The down position must be held to lower the hood.

WARNING: Keep hands clear of the hood as it closes to avoid injury in pinch area.

BD03A018

Keep all tools, service equipment and personnel clear as the hood comes down.

143

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

BD02N147

1. HOOD SWITCH

LUBRICATION/FILTERS/FLUIDS

ENGINE HOURMETER Service your machine at the intervals and locations given in the Lubrication/ Maintenance Chart. When you service your machine, use only high quality lubricants.

TRIM THIS EDGE

BD02N185

The engine hourmeter shows the amount of actual hours the engine has run. The first number to the right displays tenths of an hour and the remaining numbers to the left display hours. Use the engine hourmeter along with the Lubrication/ Maintenance Chart to service your machine at the correct time periods.

144

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

LUBRICATION/FILTERS/FLUIDS

FLUIDS AND LUBRICANTS - 721D Engine Crankcase Oil Capacity - with filter change................................... 14.2 liters (15 U.S. Quarts) Specifications ............................................... Case AKCELA No. 1 (SAE 15W-40) Cooling System Capacity ....................................................................... 25.5 liters (6.75 U.S. Gal.) Specifications .............................................. 50% water and 50% Ethylene Glycol Fuel Tank Capacity ..................................................................... 246 liters (65 U.S. Gallons) Specifications ...................................................................................... Diesel Fuel

Transmission Refill Capacity - with filter change ...............................25.5 liters (27 U.S. Quarts) Total System Capacity.................................................39.7 liters (42 U.S. Quarts) Specifications ............................................... Case AKCELA No. 1 (SAE 15W-40) Axles: Capacity (Front) ...........................................................30.2 liters (32 U.S.Quarts) Capacity (Rear) ...........................................................27.4 liters (29 U.S. Quarts) Specifications ..............................Case AKCELA Transaxle Fluid (SAE 80W-140) Grease Fittings Quantity..............................................................................................As Required Specifications .............................................. Case AKCELA Molydisulfide Grease

145

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

Hydraulic/Brake System Reservoir Refill Capacity with filter change................... 123 liters (32.5 U.S. Gal.) Total System Capacity...................................................... 193 liters (51 U.S. Gal.) Specification..........................................................Case AKCELA Hy-Tran Ultraâ

LUBRICATION/FILTERS/FLUIDS

LUBRICATION/MAINTENANCE CHART

165 178 210 162 169 181 176 169 149-154

TRIM THIS EDGE

151 151 151 163 163 163 210 133 188 214 175 174 208 184 178 181 182 181 153 174 184 SM 180 169 165 SM

Air Cleaner (See Note 1) AR Hydraulic Filter (See Note 2) AR Alternator, AC,Drive Belt AR Engine Oil Level (See Note 3) 10 Radiator Coolant Level (See Note 4) AR Transmission Oil Level (See Note 5) 50 Hydraulic Reservoir Fluid Level 50 Engine Coolant Surge Bottle (Note 50 4) Bucket and Bellcrank Pivots (See 6-10 50 Note 6) Front Drive Shaft Support Bearing 1 50 Steering Cylinder Pivots 4 100 Loader Lift Arm and Cylinder Pivots 10 100 Engine Oil (See Note 12) 500 Engine Oil Filter 500 Crankcase Ventilation Filters 500 Alternator, AC,Drive Belt 250 Tire Condition and Air Pressure 250 Cab Air Filter 250 Battery Fluid Level (See Note 7) 500 Fuel Filter 1000 Fuel Tank 500 ROPS and Seat Belt Mount Bolts 500 Axle Oil Level Front and Rear 500 Hydraulic Filter 1000 Transmission Filter (See Note 8) 1000 Transmission Oil (See Note 11) 1000 Transmission Breather 1000 Upper and Lower Chassis Pivots 2 1000 Water Separator 1000 Front and Rear Axle Differential, 1000 Planetary Oil (See Note 11) Turbocharger Mounting Bolt Torque 2000 Hydraulic Oil (See Note 9) 2000 Engine Coolant 2000 Air Filter Elements 2000 Valve Clearance 2000

146

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

ADJUST

DRAIN WATER

CHANGE

GREASE

CHECK

REPLACE

CLEAN

PAGE

SERVICE POINTS

NO. OF POINTS

INTERVALS IN HOURS

LUBRICATION/FILTERS/FLUIDS

195 SM SM

Transmission Clutch calibration (See Note10) Engine Injectors (See Note 13) Fuel Pump (See Note 13)

ADJUST

DRAIN WATER

CHANGE

GREASE

CHECK

REPLACE

PAGE

SERVICE POINTS

CLEAN

NO. OF POINTS

INTERVALS IN HOURS

1000 6000 6000

6000

NOTE NOTE NOTE NOTE NOTE NOTE NOTE NOTE NOTE NOTE NOTE NOTE NOTE

1:Service the Air Filter elements if the air filter lamp illuminates.

2:Service the Hydraulic Filter if the hydraulic filter lamp illuminates.

3::Every 10 hours of operation or once each day, whichever comes first.

4:Check the radiator coolant, and engine coolant surge bottle level if the cooling level warning lamp illuminates, or every 50 hours.

5:Check the Transmission Oil Level with the engine running and the oil warm.

6:Six for the Z-Bar and 10 for the XT. 7:Check the Battery fluid more frequently in extreme heat.

8:Replace the Transmission Filter if the transmission filter restriction lamp illuminates.

9:Or when ambient operating temperatures require.

10:Initial clutch calibration at 250 hours, 1000 hours there after. Follow transmission clutch calibration in this manual.

11:Initial fluid change at 100 hours, 1000 hours there after. Follow change information in this manual.

12:Reduce to 250 hours if CASE AKCELA No.1 Engine oil is not used.

13:Contact your Dealer.

ACCESS DOORS

BD03A025

ENGINE HOOD CONTROL PANEL

BD03A014

RADIATOR ACCESS PANEL

147

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

AR - As Required SM - See the Service Manual for this machine

LUBRICATION/FILTERS/FLUIDS

BD03A022

BD02N169

ENGINE OIL - HYDRAULIC OIL COOLER (RIGHT - HAND SIDE)

RAISE COOLING UNITS TO EXPOSE HYDRAULIC FILL CAP

TRIM THIS EDGE BD02N172

BD02N167

RADIATOR AND HYDRAULIC FLUID ACCESS DOOR

HYDRAULIC FLUID

BD00M068 BD00M063

FUSE BOX AND CAB FILTER ACCESS DOOR

RADIATOR CAP

148

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

LUBRICATION/FILTERS/FLUIDS f

BDO3A008

TRIM THIS EDGE

HYDRAULIC FILTER - TRANSMISSION FILTER ACCESS (OPTIONAL COVER SHOWN)

149

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

LUBRICATION/FILTERS/FLUIDS

GREASE FITTINGS - 50 HOURS Z-Bar Linkage Use Case AKCELA Molydisulfide Grease

2

1

B890716J

TRIM THIS EDGE

1. Bucket and Bellcrank Pivot Points ................................................................ 6 Every 50 Hours Every 50 Hours

1

2

BD02N226

BD02N227

Bucket Pivot Points.. . . . . . . . . . . . . 3

2

BD02N228

Bell Crank Pivot Points. . . . . . . . . . . .3 150

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

LUBRICATION/FILTERS/FLUIDS

GREASE FITTINGS - 100 HOURS Z-Bar Linkage Use Case AKCELA Molydisulfide Grease

1

3

4 5

TRIM THIS EDGE

2

6 7 BC01A101

1.

2.

3.

4.

5.

6.

7.

Loader Lift Arm Pivots .........................................................2 (One Each Side) Lift Cylinders (Closed End) ..................................................2 (One Each Side) Steering Cylinders (Closed End, Remote)..................................................... 2 Bucket Cylinder (Closed End), Remote .......................................................... 1 Steering Cylinder (Rod End, Remote) ............................................................ 2 Front Driveshaft Support Bearing, Remote..................................................... 1 Lift Cylinders (Rod End).......................................................2 (One Each Side)

151

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

LUBRICATION/FILTERS/FLUIDS Every 100 Hours

1

Every 100 Hours

2

5

BDO2N219 BD02N225

Loader Lift Arm Pivots. . . . . . . . . . . . 2 Lift Cylinders (closed end) . . . . . . . . . .2

Steering Cylinders (rod end) . . . . . . . .2 Every 100 Hours

Every 100 Hours

6

TRIM THIS EDGE

3

BDO2N210

Front Driveshaft Support Bearing . . . .1 BD02N224

Steering Cylinders (closed end) . . . . . 2

Every 100 Hours

Every 100 Hours

7

4

BD02N228 BD02N219

Lift Cylinders (rod end) . . . . . . . . . . . . 2

Bucket Cylinder (closed end) . . . . . . . 1

152

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

LUBRICATION/FILTERS/FLUIDS

GREASE FITTINGS - 1000 HOURS Z-Bar and XT Linkage Use Case AKCELA Molydisulfide Grease

2

1

BC00N081

1. Lower Chassis Pivot ....................................................................................... 1 2. Upper Chassis Pivot ....................................................................................... 1 3. Driveshaft slipjoint........................................................................................... 1 Every 1000 Hours

Every 1000 Hours

2

3

1 BD03A028

BD03A028

Lower Chassis Pivot . . . . . . . . . . . . . .1

Upper Chassis Pivot . . . . . . . . . . . . . .1 Driveshaft Slipjoint . . . . . . . . . . . . . . . .1

153

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

3

LUBRICATION/FILTERS/FLUIDS

GREASE FITTINGS - 50 HOURS XT Linkage Use Case AKCELA Molydisulfide Grease

1

1 907L92

TRIM THIS EDGE

1. Bucket and Bell crank Pivot Points ............................................................. 10

154

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

LUBRICATION/FILTERS/FLUIDS

GREASE FITTINGS - 100 HOURS XT Linkage

BC01A100

1. Loader Lift Arm Pivots ....................................................... 8 (Four Each Side) 2. Lift Cylinders (Closed End) ................................................. 2 (One Each Side)

1

1

1

4

5

1 2

L917L92

3.

4.

5.

6.

7.

Steering Cylinders (Closed End, Remote)...........................2 (One Each Side) Bucket Cylinder (Closed End, Remote) ...............................2 (One Each Side) Lift Cylinders (Rod End).......................................................2 (One Each Side) Front Driveshaft Support Bearing (Remote) ................................................... 1 Steering Cylinder (Rod End)................................................2 (One Each Side)

155

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

Use Case AKCELA Molydisulfide Grease

LUBRICATION/FILTERS/FLUIDS

FLUID LEVELS 10 Hours

1

BD02N153

1. ENGINE OIL CASE AKCELA NO. 1 ENGINE OIL (SAE 15W-40)

TRIM THIS EDGE

2

1

3

B910922J

2 3

BD02N185

2. RADIATOR COOLANT LEVEL ETHYLENE GLYCOL AND WATER

BD02N168

3. RADIATOR ETHYLENE GLYCOL AND WATER

156

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

LUBRICATION/FILTERS/FLUIDS

50 Hours 4 5

4

BD00N055

4. HYDRAULIC RESERVOIR CASE AKCELA HY-TRAN ULTRA â

5

TRIM THIS EDGE

4

BD03A012

5. TRANSMISSION CASE AKCELA NO. 1 15W40

B910922J

157

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

LUBRICATION/FILTERS/FLUIDS

500 Hours

BD00N050

1.FILL BATTERIES WITH DRINKING OR DISTILLED WATER (BOTH SIDES)

TRIM THIS EDGE

1

1

BS03A158

NOTE: One battery on each rear side of machine.

IMPORTANT: Machine may only be Jump Started from LEFT rear side.

158

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

LUBRICATION/FILTERS/FLUIDS

1

BC00N081

TRIM THIS EDGE

1. One battery each side.

159

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

LUBRICATION/FILTERS/FLUIDS

ENGINE LUBRICATION Engine Oil Selection Case AKCELA No. 1 Engine Oil is recommended for use in your Case Engine.

Case AKCELA Engine Oil will lubricate your engine correctly under all operating conditions.

If Case AKCELA Multi-Viscosity Engine Oil is not available, use only oil meeting API engine oil service category CH-4 (preferred) or CG-4

RH99K130

TRIM THIS EDGE

BP97H064

See the chart on following page for recommended viscosity at ambient air temperature ranges.

NOTE: Do not put Performance Additives or other oil additive products in the engine crankcase. The oil change intervals given in this manual are according to tests with Case AKCELA lubricants.

160

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

LUBRICATION/FILTERS/FLUIDS

BC02N250

NOTE: Use of an engine oil pan heater or an engine coolant heater may be required when operating temperatures are in Winter or Arctic conditions.

NOTE: The use of low viscosity oils, such as 10W-30 can be used to aid in starting the engine and in providing sufficient oil flow at ambient temperatures below - 5°C (23°F). The continuous use of low viscosity oils can decrease engine life due to wear. See the chart above for the correct oil for ambient temperatures.

161

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

Oil Viscosity/Temperature Ranges

LUBRICATION/FILTERS/FLUIDS

Engine Service Specifications Oil Level check interval ................................ Every 10 hours of operation or each day, whichever occurs first.

Oil Change interval ................................................. Every 500 hours of operation Oil filter change interval .......................................... Every 500 hours of operation or once a year whichever occurs first.

Oil type ........................................ Case AKCELA No. 1 Engine Oil (SAE 15W-40) Oil Capacity - with filter change ................................... 14.2 liters (15 U.S. Quarts)

Engine Oil Level

TRIM THIS EDGE

To check the engine oil level put the machine on a level surface and stop the engine. Remove engine oil dipstick and wi pe c l ea n wi th a cl o th. R ep la c e dipstick in tube and push the engine oil dipstick completely DOWN and then remove. If the oil level is below the ADD mark, add oil to raise the oil level to the FULL mark.

BD02N153

ENGINE OIL LEVEL DIPSTICK

162

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

LUBRICATION/FILTERS/FLUIDS

Engine Oil Change and Filter Replacement Change the engine oil and replace the oil filter and closed crankcase ventilation system filters after every 500 hours of operation or once a year whichever occurs first.

NOTE: For more complete removal of foreign material, change the engine oil while the engine is still warm from operation.

IMPORTANT: You must shorten the oil change interval if you use diesel fuel with a sulphur content of more than 0.5%.

Change the engine oil more frequently when the engine operating conditions are severe (frequent stopping and starting and high or low engine temperatures.)

1 2 BD00M010

ENGINE OIL FILTER

4. Turn the oil filter (2) c o u n t e r c l o ck w i s e t o r e m o ve .

Discard the oil filter.

BD02N160

2. Remove the engine oil drain plug (1).

5. Use a clean cloth and wipe the sealing surface of the oil filter base to remove all dirt.

NOTE: When changing engine oil the oil flow rate can be improved if the oil fill cap or dipstick is removed from the engine while draining.

6. Apply a thin layer of clean grease or oil to the gasket of the new oil filter.

3. Open the rear engine access doors.

7. Turn the new oil filter onto the base until the gasket makes contact with the base. Continue to tighten the filter for 3/4 turn with your hand.

IMPORTANT: Do not use a filter strap wrench to install the oil filter. An oil filter strap wrench can cause a leak if the filter is dented.

163

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

1. Before draining the oil, have a container that will hold at least 14.2 liters (15 qts).

LUBRICATION/FILTERS/FLUIDS 8. Remove the six screws on crankcase ventilation cover (3).

9. Remove and replace the two filters.

10. Install the crankcase ventilation cover using the six screws.

11. Install the drain plug.

12. See Engine Lubrication in this manual for the correct type and quantity of oil. Put new oil into the engine.

BD02N153

1. ENGINE OIL FILLER PIPE

3

TRIM THIS EDGE

13. Start the engine and run at idle speed. Check the engine oil filter for leaks. After two minutes, stop the engine, wait for 2 or 3 minutes, and check the engine oil level with the dipstick.

14. Close the engine access doors.

BD03A215

1. CRANKCASE VENTILATION SYSTEM

Systemgard Lubrication Analysis Program The normal engine oil change interval is every 500 hours of operation or once a year whichever occurs first. Operating conditions, quality of the engine oil and sulphur content of the fuel can change this interval. It is recommended to use the Systemgard Lubrication Analysis Program. See your dealer.

WARNING: Never drain oil or remove oil filter while engine is running.

CM107

WARNING: Replace all covers or guards after servicing or cleaning the machine. NEVER operate the machine with covers or guards removed.

CM115

164

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

LUBRICATION/FILTERS/FLUIDS

AIR FILTER SYSTEM Service Specifications Air cleaner Dust Valve interval ................................................................. As required Air filter element service interval Primary (Outer) Element ..... Service the element if the air filter indicator lamp illuminates. Replace the element after three washings. Also, replace the element after 2000 hours of operation or each year, whichever occurs first.

The shelf life of a new air cleaner element is five years. DO NOT install a new element that is more than four years old. The date of manufacture is on the end cap of the element.

165

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

Secondary (Inner) Element ........... Replace the element after the primary (outer) element has been cleaned three times, or after the primary element has been cleaned or replaced and the air filter indicator lamp is still illuminated with the engine running. Also, replace the element every 2000 hours or each year, whichever occurs first.

LUBRICATION/FILTERS/FLUIDS

Dust Valve

Primary (Outer) Element 1. Open the hood and release the four clips that secure the cover.

Check the dust valve. Make sure there is no obstruction inside the valve.

BD02N154

BD00M008

2. Pull the cover off.

TRIM THIS EDGE

NOTE: If there is a large amount of dust inside the end cover, check dust valve for proper operation

BD02N157

3. Carefully remove (outer) element.

the

primary

4. Use a clean damp cloth and clean the inside of the filter body.

5. Install a clean or new primary (outer) element. Make sure the element has full gasket contact.

6. Install the end cover and secure it by fastening the four clips.

166

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

LUBRICATION/FILTERS/FLUIDS 7. Close the engine hood.

8. Start the engine and check the air filter indicator lamp. If the air filter indicator lamp is still illuminated, replace the s econdar y (inner) element.

Secondary (Inner) Element 1. Remove the primary (outer) element. See previous page.

RD007081

WARNING: Replace all covers or guards after servicing or cleaning the machine. NEVER operate the machine with covers or guards removed.

TRIM THIS EDGE

2. Remove the secondary (inner) element. Discard the secondary (inner) element.

BD02N156

3. Use a clean damp cloth and clean the inside of the filter body.

167

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

LUBRICATION/FILTERS/FLUIDS

Cleaning the Element

4. Use a water hose without a nozzle with pressure less than 40 psi (275 kPa, 2.8 bar) to remove all soap from the element.

Check the dirty element for damage and check the rubber seal on the end.

Push the rubber seal with your finger. If the rubber seal feels hard and does not move back to original shape, discard the element.

1. Wear face protection and remove the loose dirt with compressed air a t 3 0 p s i ( 2 0 7 k Pa , 2 . 1 b a r ) maximum. Hold the nozzle at least 1 inch (25 mm) from the element.

778L94

TRIM THIS EDGE

5. Allow the element to air dry. If you use a drier, do not exceed 160°F (71°C) and make sure the air is circulating in the drier.

6. Use a light and inspect the element for holes or splits in the pleats.

Check for damage to the metal parts and rubber gasket. Replace the element if damaged.

777L94

2. Mix two tablespoons of D1400 detergent ( Case Par t Number A40910) with two gallons (7.6 liters) of water, one cup for 16 gallons (60 liters) water.

3. Soak the element in the soap solution for 15 to 20 minutes and then move the element up and down rapidly to loosen as much dirt as possible.

779L94

NOTE: If the element is not to be used for some time, cover the element with paper for storage.

780L94

168

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

LUBRICATION/FILTERS/FLUIDS

ENGINE COOLING SYSTEM Service Specifications Cooling System Capacity .............................................. 25.5 liters (6.75 U.S. Gal.) Cooling system drain, flush, and refill interval ....... Every 2000 hours of operation or each year, whichever occurs first.

Reservoir Coolant Fluid Level Check Interval ............. Every 10 hours of operation Engine coolant Level Surge Bottle Check Interval .......................... Every 50 hours

Thermostat Starts to open ................................................................................... 82°C (180°F) Completely open ............................................................................... 94°C (202°F) Radiator cap ............................................................ 103.4 kPa, 1 bar (15 psi)

A mixture of 50% Ethylene Glycol and 50% water must be used in this machine.

This mixture is used if the lowest ambient temperature is above -37°C- (34°F). If the ambient temperature is lower, adjust the mixture to 60% Ethylene Glycol and 40% water. It is recommended that Ethylene Glycol and water be used in your machine all year.

NOTE: After you fill the cooling system, mix the Ethylene Glycol and water completely by running the engine at operating temperature for approximately five minutes. This procedure must be done when the machine is in temperatures below 0°C (32°F).

WARNING: Hot coolant can spray out if radiator cap is removed. To remove radiator cap: Let system cool, turn to first notch, then wait until all pressure is released.

Scalding can result from fast removal of radiator cap.

Check and service engine cooling system according to maintenance instructions.

SA023

169

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

Coolant Mixture

LUBRICATION/FILTERS/FLUIDS

Coolant Fluid Level The coolant fluid level is monitored at the instrument cluster. When the coolant level indicator illuminates, add coolant to the radiator as required to raise the coolant level.

IMPORTANT: Cooling System is under pressure. Before adding coolant, allow radiator to cool and remove radiator cap SLOWLY.

TRIM THIS EDGE

BD02N141

BD02N185

Check the coolant reservoir fluid level when the coolant is cold and the engine is stopped. DO NOT remove the radiator cap during this check. The coolant level must be between the FULL and ADD marks on the reservoir. Add coolant as required to raise the coolant level to the FULL mark.

Radiator Fluid Level Check the radiator coolant level when the coolant is cold and the engine is stopped. Remove the radiator cap. The coolant level must be up to the radiator cap opening.

NOTE: If the radiator coolant level is low and the coolant reservoir level is at the FULL mark, check for air leaks in the hose between the radiator and coolant reservoir.

IMPORTANT: Only add the correct mixture of ethylene glycol and water to the radiator.

BD02N168

1. RADIATOR CAP

WARNING: Hot coolant can spray out if radiator cap is removed. To remove radiator cap: Let system cool, turn to first notch, then wait until all pressure is released. Scalding can result from fast removal of radiator cap.

Check and service engine cooling system according to maintenance instructions.

SA023

170

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

LUBRICATION/FILTERS/FLUIDS

Cleaning the Cooling System

DO NOT remove the radiator cap if the c o o l a n t i s h o t . H ave a c o n t a i n e r available that is capable of holding 34.1 liters (9.0 gal).

1. Open the radiator drain valve and remove the radiator cap.

2. After all coolant is removed. Close the drain valves.

3. Add cleaning solution to the cooling system and fill the cooling system w i t h c l e a n w a t e r. Fo l l o w t h e directions included with the cleaning solution.

4. After you drain the cleaning solution flush with clean water and drain the water.

5. Put a 50% mixture of Ethylene Glycol and water in the radiator.

See Coolant Mixture in this manual.

6. Start the engine and run at idle speed until the engine is at operating temperature. Check the instrument cluster monitor, if the monitor illuminates. Add coolant as required.

7. Install the radiator cap.

BD02N160

1. RADIATOR DRAIN VALVE

171

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

Drain, flush, and replace the engine coolant every 2000 hours of operation or each year, whichever occurs first.

Clean the system and replace the coolant if the coolant becomes dirty or has the color of rust.

LUBRICATION/FILTERS/FLUIDS

DIESEL FUEL SYSTEM Service Specifications Fuel Tank Capacity ...................................................... 246 liters (65 U.S. Gallons) Interval for draining water from the fuel filter ........................ 50 hours of operation Fuel filter replacement interval ..........................................1000 hours of operation or once each year, whichever occurs first Water separator replacement interval ................................1000 hours of operation

Fuel Conditioner Diesel fuel conditioner is available from your dealer. Follow the instructions on the can.

2. Disperse insoluble gummy deposits that can form in the fuel system.

The conditioner will:

3. Separate moisture from the fuel.

TRIM THIS EDGE

1. Clean the fuel injectors, valves and manifold for increased service life.

4. Stabilize the fuel in storage.

WARNING: Engine fuel is flammable and can cause a fire or an explosion.

Do not fill the fuel tank or service the fuel system near an open flame, welding, burning cigars, cigarettes, etc.

SA022

WARNING: Never refuel the machine when the engine is hot or running.

Never smoke while refueling.

M139C

Fuel Filler Cap

BD02N184

172

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

LUBRICATION/FILTERS/FLUIDS

Diesel Fuel

Fuel Storage

Use No. 2 diesel fuel in the engine of this machine. The use of other fuels can cause the loss of engine power and high fuel consumption.

If you keep fuel in storage for a period of time, you can get foreign material or water in the fuel storage tank. Many engine problems are caused by water in the fuel.

NOTE: See your fuel dealer for winter fuel requirements in your area. If the temperature of the fuel lowers below the cloud point (wax appearance point), wax crystals in the fuel will cause the engine to lose power or not start.

Keep the fuel storage tank outside and keep the fuel as cool as possible.

R e m o ve w a t e r f r o m t h e s t o r a g e container at regular periods of time.

Fill the fuel tank at the end of the day to prevent condensation in the fuel tank.

When adding fuel to the machine, remove the fuel cap SLOWLY to reduce the air pressure build up.

The diesel fuel used in this machine must meet the specifications in the chart below or Specification D975-81 of the American Society for Testing and Materials.

Specifications for Acceptable No. 2 Diesel Fuel API Gravity, Minimum ........................................................................................ 34 Flash Point, Minimum ....................................................................... 60°C (140°F) Cloud Point (wax appearance point), Maximum ...... -20°C (-5°F) See Note Above Pour Point, Maximum ............................................ -26°C (-15°F) See Note Above Distillation Temperature, 90% Point ............................ 282 to 338°C (540 to 640F) Viscosity, at 38°C (100°F) Centistokes .......................................................................................... 2.0 to 4.3 Cetane Number, Minimum ...................... 43 (45 to 55 for winter or high altitudes) Water and Sediment, by Volume, Maximum ............................................... 0.05% WARNING: Engine fuel is flammable and can cause a fire or an explosion.

Do not fill the fuel tank or service the fuel system near an open flame, welding, burning cigars, cigarettes, etc.

SA022

WARNING: Never refuel the machine when the engine is hot or running.

Never smoke while refueling.

M139C

173

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

In very cold temperatures, a mixture of N o. 1 a n d N o. 2 d i e s e l f u e l s i s temporarily permitted. See the following Note.

LUBRICATION/FILTERS/FLUIDS

Removing Water and Sediment from the Fuel System Drain the water for the fuel filter after every 50 hours of operation. Drain the water and sediment from the fuel tank after every 500 hours of operation. Replace the water separator every 1000 hours.

1. Turn the drain valve on the water separator counterclockwise 2 or 3 turns and drain the water from the fuel filter.

2. Close the drain valve.

3. Use a large enough container and drain water and sediment from the fuel tank. Dispose of water and sediment properly.

1 TRIM THIS EDGE

BD03A015

1. WATER DRAIN

174

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

LUBRICATION/FILTERS/FLUIDS

Fuel Filter Replace the fuel filter after every 1000 hours of operation.

1. Clean the filter head and the outside of the fuel filter.

1

2. Turn the filter counterclockwise and remove the filter. Discard the filter.

3. Apply a thin layer of clean oil to the gasket on the new filter.

4. Install the filter. Use your hands to tighten the filter 1/2 to 3/4 turn after the filter makes contact with the filter head.

IMPORTANT: Do not use a filter wrench when installing a new filter.

175

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

BD02N124

1. FUEL FILTER

LUBRICATION/FILTERS/FLUIDS

HYDRAULIC/BRAKE SYSTEM Service Specifications Hydraulic/Brake System Fluid Chart Hyd Reservoir Refill Capacity w/filter change ......... 123 Liters (32.5 U.S. Gallons) Total System Capacity ................................................ 193 Liters (51 U.S. Gallons) Type of Fluid.............................................................Case AKCELA Hy-Tran Ultra® Hydraulic Reservoir Fluid Level Check Interval...............................Every 50 Hours Filter Replacement Interval ................................Every 1000 Hours of Operation or if the Hydraulic Filter Warning Lamp Illuminates Hydraulic Fluid Change Interval ..................................................Every 2000 Hours or once each year, whichever occurs first.

TRIM THIS EDGE

WARNING: Pressurized hydraulic system. Before you replace the hydraulic filter or service the hydraulic system, wear face protection and slowly loosen the hydraulic reservoir fill cap to relieve the air pressure. If you do not follow these instructions, you can be injured.

SA047

Hydraulic/Brake System - Temperature Ranges

BC04F192

176

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

LUBRICATION/FILTERS/FLUIDS

Hydraulic Oil Level

4. Clean the area around the filler cap.

5. Slowly loosen the filler cap on the hy d r a u l i c r e s e r vo i r. T h i s w i l l release the air pressure in the hydraulic reservoir. Remove the f i l l e r c a p f r o m t h e hy d r a u l i c reservoir.

Check the oil level of the hydraulic reservoir every 50 hours of operation.

7. Install the filler cap and hand tighten.

To check the oil level in the hydraulic reservoir do the following:

8. Repeat steps 2-3 in reverse order.

1. Park the machine on a level surface and lower the loader bucket to the ground. Apply the parking brake.

2. Stop the engine.

3. Check the oil level in the sight gauge. If the oil is cold, the level is correct when aligned with the lower in dic ato r ma r k. If the oi l is a t operating temperature the level is corr ec t when aligned with the upper indicator mark.

To add oil to the hydraulic reservoir do the following: 1. Ensure that the hood is closed and secured.

2. Open the access cover in the hood.

The release is in the center of the hood, directly behind the cab and can be accessed from the entry side platform.

3. Pivot the air conditioning condensor or cover to the rear.

Ensure that the cooler is locked open.

177

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

BD01E132

6. After oil has been added to the hydraulic reservoir, inspect the seal on the filler cap. Replace the seal as required.

LUBRICATION/FILTERS/FLUIDS

Hydraulic Filter Replace the hydraulic filter every 1000 hours of operation or if the hydraulic oil filter LAMP illuminates.

RD98K317

Hydraulic Filter Replacement 1. Park the machine on a level surface. Lower the loader bucket to the ground and stop the engine.

Apply the parking brake.

BD00N081

TRIM THIS EDGE

Hydraulic Filter Test To check the condition of the hydraulic filter do the following.

2. Slowly loosen the filler cap on the hy d r a u l i c r e s e r vo i r. T h i s w i l l release the air pressure in the hydraulic reservoir.

1. Start the engine. If the hydraulic oil is not at operating temperature or approximately 50°C (120°F) do the following.

3. Remove the access cover. (If Equipped)

A. Dump the bucket and hold over relief while cycling the Lift arms up and down. It can take several minutes to bring the oil to operating temperature. Refer to instruction on the instrument c l u s t e r fo r u s i n g i t t o r e a d hydraulic oil temperature.

4. Use a strap wrench to remove the o l d f i l t e r. Tu r n t h e f i l t e r counterclockwise to remove.

5. Lubricate the gasket on the new filter with Case AKCELA Hy-Tran Ultra ® fluid. Turn the new filter clockwise until the filter contacts the head of the filter assembly.

Continue to tighten the filter 1/2 to 3/4 turn by hand.

B. After 15 seconds, move the c o n t r o l l ev e r t o t h e H O L D position.

C. Repeat steps a and b until the hydraulic oil temperature is 50 C (120 F).

IMPORTANT: DO NOT use a filter wrench to tighten the hydraulic filter.

2. Increase the engine speed to full t h r o t t l e . I f t h e L A M P fo r t h e hydraulic oil filter illuminates, replace filter.

6. Tighten the filler cap.

7. Start and run the engine at approximately 1000 rpm. Check for oil leaks around the filter.

178

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

LUBRICATION/FILTERS/FLUIDS 8. Stop the engine and check the hy d rau l i c oi l l evel . A d d o i l as required. See Hydraulic System in this manual fo r correct specifications.

9. Install the Equipped)

access

cover.(If

WARNING: Never drain oil or remove oil filter while engine is running.

SA047

WARNING: Replace all covers or guards after servicing or cleaning the machine. NEVER operate the machine with covers or guards removed.

TRIM THIS EDGE

SA047

179

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

LUBRICATION/FILTERS/FLUIDS

HYDRAULIC/BRAKE OIL CHANGE

8. Remove and replace the hydraulic oil filter.

Change the hydraulic/brake oil every 2000 hours of operation or one time each year, or when ambient operating temperatures require, whichever occurs first. When changing the hydraulic oil also replace the hydraulic oil filter. Have a container available that is capable of holding 68.5 liters (18 gal).

9. See Hydraulic System in this manual for the correct type and quantity of hydraulic oil. Put new oil into the reservoir.

1. Make sure the hydraulic oil is at operating temperature.

2. Park the machine on a level surface. Lower the loader bucket to the ground and apply the parking brake.

TRIM THIS EDGE

3. Stop the engine. Put a DO NOT OPERATE tag on the steer ing wheel.

4. Make sure the accumulators are completely discharged. Push down and release the brake pedal a minimum of 30 times.

5. With the key in the RUN position, cycle the pilot controller repeatedly for at least 30 seconds. Open the manual valve for the ride control and allow it to bleed for one minute or until the hiss of discharging oil cannot be heard. Close the manual valve for the ride control.

10. Install the reservoir filler cap.

11. Start the engine and run at 1000 rpm. Check for oil leaks around the filter and the drain plug.

12. Bleed the brake system to remove old oil from the system. Remove a minimum of 1 Liter of oil from each bleed screw to make sure all old oil is removed from the system (See Bleeding the brake system in this manual).

13. Operate the loader controls several times to remove any air in the lines.

14. Lower the loader bucket to the ground and stop the engine. Check the hydraulic oil level.

15. Add oil as required.

6. Open the hydraulic reservoir remote drain over the container.

The remote drain is the rearmost of the three drains behind the left rear wheel.

7. Clean the area around the filler cap and access cover. Slowly remove the filler cap of the reservoir. This will remove the air pressure from the reservoir.

180

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

LUBRICATION/FILTERS/FLUIDS

TRANSMISSION Service Specifications Transmission refill capacity with filters...........................25.5 liters (27 U.S. Quarts) Total system capacity ....................................................39.7 liters (42 U.S. Quarts) Type of oil ................................................................ Case AKCELA No. 1 15W-40 Oil level check interval ............................................................................. 50 hours Filter replacement interval ............................ After the first 100 hours of operation and then every 1000 hours there after.

Breather cleaning interval ................................................................... 1000 hours Oil change interval ....................................... After the first 100 hours of operation and then every 1000 hours there after.

WARNING: Never drain oil or remove oil filter while engine is running.

CM107

IMPORTANT: Change the transmission oil and replace the filter after the first 100 hours of operation.

Transmission Oil Viscosity/Temperature Ranges

BC04F193

181

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

IMPORTANT: If the machine is new or the transmission has been replaced or rebuilt, change the transmission oil and replace the filter after the first 100 hours of operation.

LUBRICATION/FILTERS/FLUIDS

Transmission Oil Level

Warm Oil Level Check

See this page for the two methods to check the transmission oil level.

Check the transmission oil level every 50 hours of operation when the oil is at operating temperature. Do the following.

Oil Change, Filter Replacement, and Breather Cleaning

BD03A012

TRIM THIS EDGE

1. Park the machine on a level surface.

2. Apply the parking brake.

3. Shift the NEUTRAL.

transmission

to

Ch a n ge th e tra n s m i s s i on o il a n d replace the filter after the first 100 hours of operation with a new machine or if the transmission has been replaced or rebuilt. Then, do the above service and clean the breather every 1000 hours or operation.

If possible, drain the oil when the oil is at operating temperature. More contamination is removed when the oil is at operating temperature.

1. Put the transport/service link in the LOCKED position, apply the parking brake, and stop the engine.

4. Run the engine at idle speed.

5. If the oil level is at or below the bottom of the crosshatch region, put the transport/service link in the LOCKED position and add oil to raise the oil level up to the top of the crosshatch region. See Tr a n s m i s s i o n Service Specifications in this manual for the correct oil.

2. Clean the area around the filters, drain plug, breather, and filler tube.

3. Have a container that will hold approximately 30.3 liters (8 U.S. Gallons).

Cold Oil Level Check Before you start the engine, check the transmission oil level in the sight gauge. If the oil level is below the arrow, add oil to raise the oil level up to the ar row. S ee Trans mis s ion Ser v ic e Specifications in this manual for the correct type of oil.

182

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

LUBRICATION/FILTERS/FLUIDS 4. Remove the filler tube plug.

7. Install the filter as shown. Make sure the filter is SEATED against the filter base.

8. Spin the breather cap a few times w i t h y o u r f i n g e r ev e r y 1 0 0 0 hours.(It is located directly on top of the transmission.

9. If the breather cap does not spin easily perform lines 10 and 11.

11. Install the breather.

12. Install the drain plug. Put new oil into the transmission. See Tr a n s m i s s i o n Service Specifications in this manual.

13. Check the oil level in the sight gauge.

14. Start the engine and check for oil leaks around the filters and drain plug.

BD02N124

6. Remove the transmission filter.

Discard the old transmission filter.

15. Increase the transmission oil temperature to operating temperature and check the oil level again.

16. Stop the engine and return the transpor t/ser vice link to the OPERATING position.

BD03A007

183

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

BD02N202

5. Remove the drain plug and drain the oil from the transmission.

10. Remove the breather. Clean the breather with solvent and dry with compressed air. Be sure to wear fa c e p r o t e c t i o n w h e n u s i n g compressed air.

LUBRICATION/FILTERS/FLUIDS

AXLES Service Specifications Front Axle Refill Capacity .................................................. 30.2 liters (32 U.S. Qts.) Rear Axle Refill Capacity .................................................. 27.4 liters (29 U.S. Qts.) Type of oil .................................... Case AKCELA Transaxle Fluid (SAE 80W-140) Oil change interval ................................... After the first 100 hours of operation and then every 1000 hours there after.

NOTE: DO NOT use an alternate oil in the axles. The brake components in the axles could be damaged as a result of using an alternate oil or additives.

Axle Oil Level To check the oil level at the center bowl and each planetary end, do the following procedure.

TRIM THIS EDGE

NOTE: The oil level and filler plugs in the center bowl and planetary ends are magnetic. Remove and clean these plugs after the first 50 and 100 hours of operation with a new or rebuilt axle.

184

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

LUBRICATION/FILTERS/FLUIDS

Axle Planetary and Center Bowl 1. Park the machine on a level surface. Apply the parking brake and stop the engine.

2. Remove the axle dipstick and clean area thoroughly. Check the level.

BD02N131

BD02N128

1. OIL LEVEL CHECK.

BD02N130

2. ADD OIL AS REQUIRED.

185

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

IMPORTANT: Axle level must be checked by placing dipstick level in hole but not threading down.

LUBRICATION/FILTERS/FLUIDS

Axle Oil Change Change the axle oil every 1000 hours of operation.

1. Park the machine on a level surface. Apply the parking brake and stop the engine.

2. Clean the oil level and drain plugs.

3. With the oil warm from operation, remove the oil level dipstick.

TRIM THIS EDGE

BD02N123

BD01E136

3. WHEEL END DRAIN (ONE EACH SIDE)

1. REAR CENTER BOWL DRAIN PLUG

5. After removal of the oil install the center bowl and wheel end drain plugs.

6. Fill axle with new oil.

BD02N178

2. FRONT CENTER BOWL DRAIN

4. Remove the drain plug from the axle center bowl and each wheel end drain. Have a container with enough capacity to hold 30.2 L (32 qts).

BD02N130

4. AXLE DIPSTICK

7. Check oil level by placing the d i p s t i ck i n t o t h e h o l e bu t n o t running the threads down.

186

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

LUBRICATION/FILTERS/FLUIDS

BD02N131

5. AXLE DIPSTICK IN THE CHECK POSITION (THREADS NOT RUN DOWN)

TRIM THIS EDGE

8. Install and secure the dipstick.

187

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

LUBRICATION/FILTERS/FLUIDS

CAB AIR FILTERS Clean or replace the cab air filters (if equipped) every 250 hours of operation or if the air flow in the cab is reduced.

NOTE: If your machine is new, make sure the plastic cover is removed from the filters.

3. Install a filter that has been cleaned or a new filter.

4. Close the access door and turn the handle to the locked position.

Circulation Cover

Removal and Installation 1. Turn the handle and open the access door.

TRIM THIS EDGE

BD00N028

1. Remove the air circulation filter.

2. Install a filter that has been cleaned or a new filter.

BD03A043

2. Pull the air filter out.

BD03A044

188

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

LUBRICATION/FILTERS/FLUIDS

Cleaning the Filter Check the dirty element for damage and check the rubber seal on the end.

Push the rubber seal with your finger. If the rubber feels hard and does not move back to original shape, discard the element.

3. Soak the element in the soap solution for 15 to 20 minutes and then shake the element up and down rapidly to loosen as much dirt as possible.

1. Remove the loose dirt with compressed air, 30 psi (207 kPa, 2 bar) maximum. Hold the nozzle at least one inch (25 mm) from the element. Make sure you wear face protection when using compressed air.

786L94

2. Mix two tablespoons of D1400 d et e r g e n t ( C a s e p a r t nu mb e r A40910) with two gallons (7.6 liters) of water, one cup for 16 gallons (60 liters) of water.

788L94

5. Allow the element to air dry. If you use a drier, do not exceed 160°F (71°C) and make sure the air is circulating in the drier.

189

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

787L94

4. Use a water hose without a nozzle with pressure less than 40 psi (275 kPa, 2.7 bar) to flush all soap from the element.

LUBRICATION/FILTERS/FLUIDS 6. Use a light and inspect the element for holes or splits in the pleats.

Check for damage to the metal parts and rubber gasket.

789L94

NOTE: If the element is not to be used for some time, wrap the element with paper for storage.

WINDSHIELD WASHER RESERVOIR (IF EQUIPPED) TRIM THIS EDGE BD02N142

The windshield washer reservoir is located in the left side of the engine compartment.

IMPORTANT: When the ambient temperature decreases to 0°C (32°F) and below, always use an antifreeze type washer solution.

190

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

LUBRICATION/FILTERS/FLUIDS

TRIM THIS EDGE

NOTES

191

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

LUBRICATION/FILTERS/FLUIDS

TRIM THIS EDGE 192

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

MAINTENANCE/ADJUSTMENT CAB SERVICE Air Conditioning (If Equipped) The components of the operators cab, including the components of the air conditioning system, require service at different intervals. Service the following items as required to maintain maximum operating efficiency.

!

WARNING: Liquid refrigerant can cause severe and painful frostbite to your skin. Do not attempt to service the air conditioning system on this machine unless you are completely familiarized with air conditioning and the safety precautions which must be followed. Serious injury can result if you do not follow these instructions.

Lubrication of the Air Conditioning Compressor Seals Operate the air conditioning once every 250 hours to lubricate the compressor seals. Turn the air conditioning control to MAXIMUM for at least 15 minutes. In temperatures below 32°F (0°C) put a c o v e r o ve r t h e a i r c o n d i t i o n i n g condenser. This will make sure the refrigerant and lubricants in the system will be at operating temperature.

Keep the air conditioning condenser core clean. Use compressed air (wear face protection) or a rigid brush to clean the condenser. Also check and clean the grille screen.

IMPORTANT: Because the condenser fins bend easily, be careful when you clean the condenser.

BD00M063

1. CONDENSER

191

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE (First)

TRIM THIS EDGE

SA048

MAINTENANCE/ADJUSTMENT

RADIATOR/COOLER ACCESS FOR CLEANING (Additional radiator access can be gained on both the LH & RH sides of the machine).

1. Remove bolts from each end of the plastic fender insert.

2. Slide fender insert to the rear of the machine 25mm (1 inch) to disengage fender insert from rear frame side plate.

3. The lower areas and radiator/cooler in general can be cleaned using shopvacuum and or pressure washer.

IMPORTANT: Be careful not to bend or damage radiator/cooler fins during cleaning. DO NOT exceed 6890 kPa (1000 psi) nozzle pressure when cleaning.

TRIM THIS EDGE

2 2 1

BD04G022

1. INSERT

2. BOLTS

192

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

MAINTENANCE/ADJUSTMENT

Cab Headliner

Door Hinges

T h e fo a m h e a d l i n e r i n y o u r c a b decreases noise. To keep the headliner in good operating condition, remove dust with a vacuum cleaner.

Use graphite to lubricate all hinges. DO NOT use oil.

IMPORTANT: DO NOT wash the headliner with water because water can cause damage to the headliner and lower the noise control capacity of the headliner.

Check all hoses and wiring for damage.

If damage occurred, see your dealer for repair or replacement.

RD97F215

193

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

Hoses and Wiring

MAINTENANCE/ADJUSTMENT

Operators Seat Remove dust and dirt from the seat with a vacuum cleaner or soft brush. Clean stains with the correct use of a material cleaner.

Before removing stains, try to find what type and how old the stains are. Some stains can be removed with water or soap solution.

!

WARNING: Never use gasoline, naptha or any other volatile material for any cleaning purposes. These materials may be toxic and/or flammable.

SA049

CLEANER FLUID - This type of cleaner can be used for grease or oil stains.

Carefully remove the item that caused the stain with a scraper or a knife that is not sharp. Use very little cleaner, no pressure, and clean cloths. Move the cloth from the outside of the stain toward the center of the stain and constantly change to a clean section of cloth.

When the stain is removed from the material, immediately use a cloth to make dry the area and to prevent a cleaner circle pattern. If a circle pattern occurs, clean the complete area.

TRIM THIS EDGE

NOTE: A difficult stain can need a second application of cleaner fluid followed immediately by the use of a soft brush to completely remove the stain.

194

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

MAINTENANCE/ADJUSTMENT

TRANSMISSION CLUTCH CALIBRATION Transmission clutch calibration ensures optimum shifting of the transmission.

Make sure of the following before proceeding with transmission clutch calibration.

A. The parking brake has been tested.

B. The transmission oil is warm.

C. The engine idle speed is correct.

D. The transmission is in neutral.

E. The parking brake is applied.

Do the following procedure to calibrate the transmission clutches: 1. Put the transmission in manual shift mode and the gear selector in 3rd gear neutral.

2. Press the program switch.

3. Press the up-count switch until the display reads 011.

5. Press the up-count switch twice so the display reads 02.

At this time, 2 00 00 will begin flashing in the display center. ●

After one second, the Clutch Calibration Main Code status will be displayed in the 3rd and 4th spaces (2 XX 00 - the XX represents the 3rd and 4th spaces).

●

The Modulation Cycle Number will be displayed in the 1st and 2nd spaces (2 00 XX - the XX represents the 1st and 2nd spaces).

●

During Clutch Calibration, the Clutch Calibration Main Code will change from 01 to 07 as the process is completed. The code 07 will indicate that the process is complete and the Information Center will return to normal working status.

●

If any of the Clutch Calibration parameters are incorrect, the display center will stop flashing and display the Clutch Calibration Main Code in the 1st, 2nd, 3rd, and 4th spaces.

In the event, the code in the 3rd and 4th spaces will be 09 to 14 and will indicate the process that the calibration was in when it was aborted.

The 1st and 2nd spaces will produce the Clutch Calibration Sub-Code, which is the code that will inform the operator of the reason process was aborted.

6. After completing the clutch calibration procedure, turn the engine off for 15 seconds to set the calibration in the controller.

NOTE: See Clutch Calibration Main Code and Clutch Calibration Sub-Code on the following page

195

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

4. Return the program switch to the center position.

MAINTENANCE/ADJUSTMENT

Clutch Calibration Main Codes CLUTCH CALIBRATION MAIN CODE 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14

Clutch Calibration SubCodes CLUTCH CALIBRATION SUB-CODE

MEANING Clutch Calibration Mode was not initiated because one of the requirements was not met.

Adjusting 1st gear Adjusting 2nd gear Adjusting 3rd gear Adjusting 4th gear Adjusting Forward gear Adjusting Reverse gear Clutch Calibration Completed Operator aborted calibration procedure.

Aborted while adjusting 1st gear Aborted while adjusting 2nd gear Aborted while adjusting 3rd gear Aborted while adjusting 4th gear Aborted while adjusting Forward gear Aborted while adjusting Reverse gear

MEANING Calibration in process

00 01 02 03 04 05 06 07 08

Fault present Shift lever not in neutral Park brake not applied Output speed not 0 kph/mph Low transmission oil temperature High transmission oil temperature Low engine RPM High engine RPM

TRIM THIS EDGE

DECLUTCH ADJUSTMENT 1. Park the machine on a level surface.

2

2. Lower the loader bucket to the floor.

3. Apply the parking brake and stop the engine.

NOTE: The following photo shows the brake pedal/valve assembly removed for clarity. Do not remove the brake pedal/valve assembly from the machine.

1

BD00C006

1. PLUG 2. ADJUSTMENT SCREW 3. REMOVE THE PLUG (1) FROM THE BASE OF THE LEFT HAND BRAKE PEDAL/ VALVE ASSEMBLY.

196

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

MAINTENANCE/ADJUSTMENT

SECONDARY STEERING CHECK NOTE: Test the secondary steering a minimum of every 250 hours.

BD02N185

1. Prior to checking the secondary steering system, park the machine on hard packed level ground with enough clearance around the machine to allow you to completely steer from side to side. Raise the bucket approximately 500 mm (20 inches) above the ground.

2. With the key on and the engine off, confirm the secondary steering light within the cluster is on. This indicates the steering pressure is low.

3. Start the machine and let the engine run for a few seconds. Confirm the secondary steering light is out after the first second. This confirms the electrical function of the circuit is operating correctly and also confirms pressure has been built and the module has been armed.

4. With the machine at low idle and steering straight ahead, turn the key switch to the OFF position to stop the engine and then immediately back to the ON position (not start position). The secondary steering pump/motor should start running immediately. Confirm the light is on and the motor is running.

5. Steer the machine full left and then full right to confirm that the secondary steering pump is working. Confirm there is no lack of steering function.

6. Look at the instrument cluster to verify that the secondary steering light comes on.

IMPORTANT: Do not run the secondary pump/motor continuously for more than 20 seconds at a time without a 2 minute cool down.

197

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

The secondary steering system is electrically powered which allows you to steer the machine if the primary steering system stops working. Always maintain the batteries.

MAINTENANCE/ADJUSTMENT 7. Restart the engine. Confirm the secondary steering light stays on. The secondary steering motor should stop after about 3 seconds and the secondary steering light should go out.

8. If steps 2 through 7 function properly, the secondary steering is operating correctly. If not, repair and retest.

9. Let the engine run and allow the batteries to recharge for a minimum of 10 minutes.

ATTENTION: Do not turn the key switch off if the machine is steered against either the right hand or left hand steering stop. The steering wheel may kick back.

PARKING BRAKE CHECK NOTE: Test the parking brake at a maximum of 250 hours.

Before you operate the machine periodically test the parking brake functions.

TRIM THIS EDGE BD02N185

1. To release the park brake, all the following are required: A. Push the Park Brake switch to the release position.

B. Service brake depressed indicating brake lights.

C. Transmission shifter positioned from N to F or R for a second, and back to N. D. Adequate service brake pressure to stop the machine.

2. To engage the park brake, any of the following is required: A. Loss of service brake pressure in both axles.

B. Loss of system electrical power (key OFF).

198

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

MAINTENANCE/ADJUSTMENT C. Park Brake switch in engaged position.

3. To test these functions: A. Start on a clear level surface.

B. With Step 1, A through C complete, start the engine release the park brake, red warning light out.

C. Shutdown the engine turn the key switch to the ON position, engine off the Park Brake light should come ON. D. Release the park Brake using B and C in Step 1. Make sure the park brake light is out.

E. Pump the service brakes, the low brake pressure warning light should come ON first. Continue to pump the service brakes. Pump until the park brake light comes ON, pump the brakes three more times, it could require as many as forty pumps total.

F. Start the engine and allow the brake pressure to build until the warning light goes out.

H. Put the transmission in F or R and back to N the brake light must stay ON. I. Put the park brake switch in the engaged position, attempt B and C in Step 1. The park brake light must stay ON. 4. Put the park brake switch in the release position, attempt B and C in Step 1.

The park brake light must turn OFF, A. Allow the machine to roll slowly forward with the transmission in F put the park switch to engage. The machine must come to a stop immediately.

Park light ON. Transmission disengages.

If all steps are working positive the system works correct. If there was a problem with the test contact your dealer.

199

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

G. Depress the service brake and release. The light must stay ON.

MAINTENANCE/ADJUSTMENT

LOADER ADJUSTMENTS Height Control and Return To Travel Adjustment Procedure 6 2

5

1

TRIM THIS EDGE

4

3

BS00N076

1. Proximity Switch

4. Height Control Target

2. Return to Travel Target

5. Lift Arm

3. Target Mounting Plate

6. Front Chassis (Top Left Hand Side)

1. To avoid damage to the proximity switch, it must be adjusted back, away from the lift arm, to clear everything on the lift arm as it sweeps past.

2. Start the engine. Position the bucket flat on the ground. Shut the machine off.

Locate the return to travel target opposite the proximity switch and then tighten it to the target mounting plate. Next adjust the proximity switch out toward the target until and air gap of 3.5 to 5.0 mm (1/8 to 3/16 inch) is obtained. Lock the proximity switch in position with its jam nut. Torque the jam nut to 5 ft.lbs.

200

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

MAINTENANCE/ADJUSTMENT

A

2

B

BX00N077

2.) Return to Travel Target 4.) Height Control Target

3. The Location of the height control target within its slot in the target mounting plate will determine the automatic stopping height of the lift arms as they are raised. The higher the target is positioned in its slot in the target mounting plate, the lower the lift arms will automatically stop as they are raised. Position the target per the table below. Tighten the target in this position.

MACHINE

A mm (in)

APPROXIMATE B mm (in) APPROXIMATE RESULTRESULTING REING HEIGHT CONTROL TURN TO TRAVEL HINGE PIN HEIGHT mm HINGE PIN (in) HEIGHT

721D Z-BAR

56 (2.20in)

403 (15.87 in)

42 (1.65 in)

3302 (130 in)

721D XT

60 (2.36 in)

386 (15.20 in)

32 (1.26 in)

3302 (130 in)

4. The location of the return to travel target within its slot in the target mounting plate will determine where the lift arms will automatically stop while they are lowered. The higher this target is located in its slot in the target mounting plate the lower the lift arms will automatically stop as they are lowered. Position the target per the above table. Tighten the target in this position.

201

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

4

MAINTENANCE/ADJUSTMENT 5. Make sure the proximity switch and all the mounting bolts are tight. Start the engine. Set the detent switch to the on position, and set the return to travel/ float detent switch to the return to travel position. Raise the lift arms to approximately the horizontal position. Put the loader control lever in the raise position, and verify that the electromagnet holds it in that position until the height control target passes in front of the proximity switch. Next, with the lift arms still raised, put the loader control lever in the lower position, and verify that the electromagnet holds it in that position until the return to travel target passes in front of the proximity switch. Position the bucket flat on the ground.

Shut the machine off.

XT Return To Dig Adjustment Procedure 1 2 6 TRIM THIS EDGE

5 3 4

BS00N078

1. Tilt Cylinder (Left Hand Side)

4. Target Bar

2. Proximity Switch Mounting Bracket

5. Proximity Switch

3. Proximity Switch Guard

6. Target Mounting Bracket

1. Start the engine. Raise the lift arms until they are approximately horizontal.

Roll the bucket all the way back. Lower the arms until they are on the ground.

Shut the machine off.

2. Loosen the bolts holding the target mounting bracket to the tilt cylinder clevis.

Align the target mounting bracket parallel to the tilt cylinder, and tighten the bolts.

3. Loosen the bolts holding the target bar to the target mounting bracket. Align the target bar parallel to the tilt cylinder, and tighten the bolts.

202

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

MAINTENANCE/ADJUSTMENT 4. Loosen the bolts holding the proximity switch mounting bracket to the cylinder.

Position the proximity switch face parallel to the target bar surface, and tighten the bolts. Next adjust the proximity switch out toward the target bar until and air gap of 3.5 - 5.0 mm (1/8 - 3/16 inch) is obtained. The proximity switch must not protrude past the proximity switch guard. Lock the proximity switch in position with its jam nut. Torque the jam nut to 5.0 ft. lbs.

5. Start the engine. Position the bucket flat on the ground. Shut the machine off.

Loosen the bolts holding the target bar to the target mounting bracket. Slide the target bar away from the proximity switch until the face of the proximity switch is completely uncovered. Align the target bar parallel to the tilt cylinder, and tighten the bolts.

7. Loosen the bolts holding the target bar to the target mounting bracket. Slowly slide the target bar towards the proximity switch. When the proximity switch face is nearly covered by the target bar, the switch will be activated, and the control lever will return to the center position. Tighten the bolts maintaining this location of the target bar. Verify that the 3.5 to 5.0 mm (1/8-3/16 inch) gap is maintained between the target bar and the proximity switch.

8. Make sure the proximity switch and all the mounting bolts are tight. Start the engine. Set the detent switch to the on position, and set the return to travel/ float detent switch to the return to travel position. Raise the lift arms to approximately the horizontal position. Position the bucket to the fully dumped position. Put the loader control lever in the roll back position, and verify that the electromagnet holds it in that position until the end of the target bar passes in front of the proximity switch. Lower the lift arms to the ground, and verify the bucket is flat on the ground.

203

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

6. Turn the ignition switch to the on position (not accessory position). Do not start the engine. Position the bucket control lever to the full roll back position.

The electromagnetic detent should hold the control lever in this position.

MAINTENANCE/ADJUSTMENT

Z-Bar Return To Dig Adjustment Procedure

1 3

2

TRIM THIS EDGE

7 5

6 4 BS00N079

1. Bell Crank

4. Proximity Switch Guard

2. Target Mounting Bracket

5. Proximity Switch

3. Tilt Cylinder

6. Proximity Switch Mounting Bracket 7. Target Bar

1. Start the engine. Raise the lift arms until they are approximately horizontal.

Fully dump the bucket. Lower the arms until bucket edge is on the ground.

Shut the machine off.

2. Loosen the bolts holding the target mounting bracket to the tilt cylinder eye.

Align the target mounting bracket parallel to the tilt cylinder, and tighten the bolts.

3. Loosen the bolts holding the target bar to the target mounting bracket. Align the target bar parallel to the tilt cylinder, and tighten the bolts.

204

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

MAINTENANCE/ADJUSTMENT 4. Loosen the bolts holding the proximity switch mounting bracket to the tilt cylinder. Position the proximity switch face parallel to the target bar surface, and tighten the bolts. Next adjust the proximity switch face parallel to the target bar surface, and tighten the bolts. Next adjust the proximity switch out toward the target bar until an air gap of 3.5 to 5.0 mm (1/8 to 3/16 inch) is obtained. The proximity switch must not protrude past the proximity switch guard. Lock the proximity switch in position with its jam nuts. Torque the jam nut to 5.0 ft. lbs.

5. Start the engine. Position the bucket flat on the ground. Shut the machine off.

Loosen the bolts holding the target bar to the target mounting bracket. Slide the target bar towards the proximity switch until the face of the proximity switch is com0letely covered. Align the target bar parallel to the tilt cylinder, and tighten the bolts.

7. Loosen the bolts holding the target bar to the target mounting bracket. Slowly slide the target bar away from the proximity switch. When the proximity switch face is nearly uncovered, the switch will be activated, and the control lever will return to the center position. Tighten the bolts maintaining this location of the target bar. Verify that the 3.5 to 5.0 mm (1/8 to 3/16 inch) gap is maintained between the target bar and the proximity switch.

8. Make sure the proximity switch and all the mounting bolts are tight. Start the engine. Set the detent switch to the on position, and set the return to travel/ float detent switch to the return to travel position. Raise the lift arms to approximately the horizontal position. Position the bucket to the fully dumped position. Put the loader control lever in the roll back position, and verify that the electromagnet holds it in that position until the end of the target bar passes in front of the proximity switch. Lower the lift arms to the ground, and verify the bucket is flat on the ground.

205

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

6. Turn the ignition switch to the on position (not accessory position). Do not start the engine. Position the bucket control lever to the full roll back position.

The electromagnetic detent should hold the control lever in this position.

MAINTENANCE/ADJUSTMENT

Bucket Height Control Minor Adjustment 1. Park the machine on a level surface. Lower the loader bucket to the floor.

2. Apply the parking brake and stop the engine.

3. Loosen the rear actuator.

4. To increase the dump height, move the actuator down in the slot. To decrease the dump height, move the actuator up.

5. Tighten the actuator.

6. Start the engine and pull the lift control lever to the RAISE detent position.

When the loader arms stop moving, check the dump height.

TRIM THIS EDGE 206

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

MAINTENANCE/ADJUSTMENT

ROLL-OVER PROTECTIVE STRUCTURE Yo u r m a c h i n e h a s a R o l l - O v e r Protective Structure (ROPS). A ROPS label shows the serial number of the ROPS, gross weight, appr oval, regulation, and model numbers of the machine. See Identification Numbers in this manual.

5. Do not put the seat belts in bleach or dye. You will make the seat belts weak.

Maintenance and Inspection of ROPS After the first 20 hours of operation and after every 500 hours of operation, do the following: 1. Check the torque of the ROPS m o u nt i n g b o l t s. I f n e c e s s a r y, tighten the bolts to the correct torque. See torque specifications on this page.

RD98K304

ROPS CANOPY LABEL

Seat Belt The seat belt is an important part of your ROPS. You must wear the seat belt at all times when you operate the machine.

2. Check the operators seat and the mounting parts for the seat belt.

Tighten the bolts to the correct torque. See Torque Specifications in this manual. Replace parts that have wear or damage.

3. Check for cracks, rust, or holes in the ROPS and ROPS parts. Age, weather, and accidents can cause damage to the ROPS and ROPS parts. If you have any doubt about the ROPS system, see your dealer.

1. Keep the seat belts away from objects that can damage the seat belts.

2. Check the seat belts for damage.

Replace all par ts that are damaged.

3. Make sure that the mounting bolts of the seat belts are tight. See Torque Specifications for Seat in this manual.

207

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

Before you operate this machine, always make sure that the ROPS and operator’s seat belts are correctly installed.

4. Keep the seat belts clean. Wash the seat belts only in soap and water.

MAINTENANCE/ADJUSTMENT

Torque Specifications for ROPS Cab and ROPS Canopy

BD00M101

ROPS CAB AND ROPS CANOPY MOUNTING BOLTS (BOTH SIDES), TIGHTEN TO 772 TO 854 Nm (580 TO 630 POUND-FEET)

TRIM THIS EDGE

NOTE: Torque specifications are for clean, dry threads.

208

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

MAINTENANCE/ADJUSTMENT

Damage to the ROPS If the machine has rolled over or the ROPS has been in some other type of accident (such as hitting an overhead object during transport), you must replace the damaged ROPS components to get as much protection as you had originally.

After an accident, check the following for damage.

A. ROPS canopy or cab.

B. Operators seat.

C. Seat belt mounting bolts and seat belt.

Before you operate the machine, replace all ROPS components that are damaged.

See the Parts Catalog or your dealer for components that are replaceable.

!

WARNING: Improper ROPS inspection or maintenance can cause injury or death. Do the recommended ROPS inspection shown in this manual. If you must replace the ROPS, ROPS parts, or ROPS mounting hardware, use only the replacement parts shown in the Case parts catalog for this machine SA029

!

WARNING: Do not modify ROPS in any manner. Unauthorized modifications such as welding, drilling, cutting or adding attachments can weaken the structure and reduce your protection. Replace ROPS if subjected to roll-over or damage. Do not attempt to repair.

SB026

!

WARNING: If you operate this machine without a ROPS and the machine rolls over, you can be injured or killed. Remove the ROPS only for service or replacement. Do not operate this machine with the ROPS removed.

SA027

!

WARNING: Adding additional weight (attachments, etc.) to the machine can cause injury or death. Do not exceed the gross weight printed on the ROPS label SA028

!

WARNING: Always fasten the seat belt securely before starting the engine SA036

209

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

DO NOT TRY TO WELD OR STRAIGHTEN THE ROPS.

MAINTENANCE/ADJUSTMENT

TORQUE SPECIFICATIONS FOR SEAT AND SEAT BELTS 1

2

1 TRIM THIS EDGE 6397

1. 54-61 NM (40-45 FT LB) 2. 73-87 NM (54-64 FT LB)

210

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

MAINTENANCE/ADJUSTMENT

ALTERNATOR BELT AND AIR CONDITIONING COMPRESSOR BELT Service Interval Belt service interval .................................................................... Check as required Air conditioning compressor belt service interval ................Check every 250 hours 1. Park the machine on a level surface and apply the par king brake.

2. Open the hood.

BD03A031

5. Install a 3/8 inch breaker bar in the tension pulley bracket.

6. Push the breaker bar forward just enough to release the tension on the drive belt.

BD03A033

2 SCREWS ON EACH SIDE

4. Remove the 4 screws that hold the protective cover.

211

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

3. Turn the master disconnect switch off.

MAINTENANCE/ADJUSTMENT

FIRE EXTINGUISHER MOUNTING (IF EQUIPPED) Type of Fire Extinguisher It is recommended that you have a fire extinguisher on your machine. The fire extinguisher shown below is available from your dealer and can be installed on the machine.

This dry chemical fire extinguisher has a 5 pound capacity and is approved for Cl as s A , B and C ty pe fi r es. Th e operating temperature is from -65° to 120°F (-54° to 49°C).

Inspection and Care EVERY MONTH - It is recommended that you inspect the fire extinguisher once each month for damage and to i n s ur e t h at t he g a ug e i s wor k i n g correctly.

TRIM THIS EDGE

EVERY 6 MONTHS - Have the dr y chemical removed and refilled by a fire equipment technician.

ONCE EACH YEAR - Have the fire equipment technician inspect the fire extinguisher.

153L95

IMPORTANT: DO NOT mount the Fire Extinguisher on any part of the ROPS or FOPS structure. DO NOT make any modifications to the ROPS or FOPS structure.

212

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

MAINTENANCE/ADJUSTMENT

TRIM THIS EDGE

NOTES

213

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

MAINTENANCE/ADJUSTMENT

TRIM THIS EDGE 214

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

ELECTRICAL SYSTEM Battery Safety

!

WARNING: Before you service a battery, always wear face protection, protective gloves and protective clothing. Battery acid or battery explosion can cause serious injuries.

SA046

!

WARNING: Battery acid causes severe burns. Batteries contain sulfuric acid. Avoid contact with skin, eyes or clothing. Antidote - EXTERNAL: flush with water. INTERNAL: drink large quantities of water or milk. Follow with milk of magnesia, beaten egg or vegetable oil. Call physician immediately.

EYES: flush with water for 15 minutes and get prompt medical attention.

!

WARNING: When the battery electrolyte is frozen, the battery can explode if, (1) you try to charge the battery, or (2) you try to jump start and run the engine. To prevent the battery electrolyte from freezing, try to keep the battery at full charge. If you do not follow these instructions, you or others in the area can be injured.

SA033

!

WARNING: Sparks or flame can cause hydrogen gas in a battery to explode. To prevent an explosion, do the following: 1. When you disconnect the battery cables, always disconnect the negative (1) battery cable first.

2. When you connect the battery cables, always connect the negative (-) cable last.

3. Do not short circuit the battery posts with metal items.

4. Do not weld, grind, or smoke near a battery.

SB034

BATTERY SERVICE NOTE: The electrical system in this machine is 24 volts. Each battery is 12 volts.

Before you service components of the electrical system, always disconnect the NEGATIVE (-) battery cable.

Before you use an electric welder, disconnect the alter nator wires, instrument cluster, and turn the master disconnect switch to OFF. Do not use a steam cleaner or cleaning solvent to clean the alternator.

Do not run the engine with the battery c a bl e s d i s c o n n e c t e d o r w i t h t h e alternator wires disconnected.

213

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE (First)

TRIM THIS EDGE

SB032

ELECTRICAL SYSTEM

Battery Fluid Level Check the fluid level of the batteries every 500 hours of operation. If the machine is operated in a warmer climate check the fluid level more often. If the fluid level is low, add clean or distilled water to each cell until the fluid level is at the split ring at the bottom of each cell opening.

IMPORTANT: If the temperature is 32°F (0°C) or below and you have added water to the batteries, do the following; Connect a battery charger to the batteries or operate the machine for approximately two hours. This procedure is necessary to mix the water with the electrolyte.

Battery Vents Keep the battery vents clean, make sure the vents are not restricted.

Cleaning the Batteries TRIM THIS EDGE

Check the batteries and battery compartment regularly for dirt, corrosion and damage. Dirt mixed with electrolyte or moisture on the top of the batteries can cause a discharged condition in the batteries. Use one of the following methods to clean the batteries.

1. Use Case Battery Saver, Part Number M20376. Follow the instructions on the container. This cleaner does not need water.

2. Use baking soda or ammonia and flush the outside of the batteries with water.

If you do not have Case Battery Saver, use other special cleaners to prevent corrosion on the battery terminals.

214

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

ELECTRICAL SYSTEM

1 1

BD02N165

BD02N162

BATTERY COVER

IMPORTANT: Machine must be Jump Started from the LEFT side only!

215

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

To access the batteries, right or left side, remove the two bolts that secure the cover. Handles are provided for easy removal and installation (1). (one ea. side)

ELECTRICAL SYSTEM

FUSES The fuses in this machine are blade type. To replace, pull the old fuse straight out and push the new fuse straight in. The amperage for each fuse is stamped on the fuse. Refer to the fuse panel decal for correct location of each fuse.

RD97F154

TRIM THIS EDGE BD03A078

The fuse decal is located inside the access door.

NOTE: See the following page for detail of fuse information.

216

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

ELECTRICAL SYSTEM

REPLACEMENT FUSES AMP

FUNCTION

A

7.5

TRANSMISSION CONTROL

B

5

FLASHER MODULE

C

5

RIDE/PILOT CONTROL

D

5

PARKING BRAKE

E

10

GRID HEATER

F

5

ENGINE SHUTDOWN

G

15

BLOWER SWITCH

H

5

BACK UP ALARM

J

10

FRONT WIPER/WASHER

K

10

REAR WIPER/WASHER

L

7.5

RADIO/CONVERTER

M

7.5

SECONDARY STEERING

N

10

COMPRESSOR (SEAT)

P

7.5

COUPLER/FAN REVERSER

R

7.5

SECONDARY STEERING

S

5

T

7.5

TRANSMISSION CONTROL

U

7.5

DOME LAMP-ENG COMP-HORN

V

7.5

VOLTMETER

W

15

CIGARETTE LIGHTER

X

7.5

BEACON

Z

10

FRONT FLOOD LIGHTS

A’

10

REAR FLOOD LIGHTS

B’

5

HIGH BEAM LEFT

C’

5

HIGH BEAM RIGHT

D’

5

LOW BEAM LEFT

E’

5

LOW BEAM RIGHT

F’

5

LEFT TAIL LIGHTS

G’

5

RIGHT TAIL LIGHTS

INSTRUMENT CLUSTER

Y

217

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

FUSE

ELECTRICAL SYSTEM

SERVICE ELECTRICAL CONNECTOR (IF EQUIPPED) The cigar lighter socket (24 volt) can be used for the connection of a lighting d ev i c e t o h e l p w i t h s e r v i c e a n d maintenance procedures.

NOTE: This is a 24 volt outlet.

BD00B030

AUXILIARY POWER OUTLET (IF EQUIPPED) TRIM THIS EDGE

The Auxiliary Power Outlet socket (12 volt) can be used for the connection of a lighting device to help with service and maintenance procedures.

NOTE: This is a 12 volt outlet.

BD00B003

218

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

ELECTRICAL SYSTEM

AUXILIARY POWER EQUIPMENT MOUNTING BRACKET LOCATION The auxiliar y power equipment mounting brackets are located behind the right and left ROPS post covers.

Th es e b ra cke ts a r e for m o un ti n g radios, phones, etc.

1

BD00B009

1. RIGHT ROPS POST COVER

TRIM THIS EDGE

To locate the bottom of the mounting bracket measure 300 mm (11.8 inches) from the bottom edge of the plastic panel. To locate the top of the mounting bracket measure 420 mm (16.5 inches) from the bottom edge of the plastic panel. The mounting bracket is approximately 70 mm (2.75 inches) wide.

219

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

ELECTRICAL SYSTEM

REPLACEMENT BULBS CASE PART NUMBER HEADLAMP HIGH BEAM

INDUSTRY NUMBER

410942A1

H3

HEADLAMP LOW BEAM

410941A1

H7

STOP/TURN/REVERSE

410939A1

S8

TAIL LAMP

411085A1

R10W

POSITION

410940A1

T4W

DOME LAMP

395185A1

Osvam 6429

CONSOLE LAMP

---

464

ROTATING BEACON *

P40533 (Halogen)

----

* DO NOT touch the new halogen bulb with your fingers. Use gloves or use a tissue to hold the bulb.

TRIM THIS EDGE 220

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

MACHINE STORAGE Storage Preparation

1. Wash the machine.

2. Lubricate the machine at all grease fittings.

3. Paint any areas where the paint has been damaged.

4. Move all hydraulic controls to relieve any pressur e in the hydraulic circuits.

5. Drain the fuel tank.

6. Put approximately 8 liters (2 U.S. Gallons) of diesel flushing oil in the fuel tank. Run the engine until the exhaust smoke is blue-white.

7. Drain the flushing oil from the fuel tank.

8. Put 15 ml (one tablespoon) of Shell Oil Company VPI crystals in the fuel tank.

10. Drain the cooling system. Leave the drain open and do not tighten the radiator cap. Put a Do Not Operate tag in the cab.

11. Clean or replace the element for the air filter.

primary

12. Cover the exposed steering cylinder rods, equipment valve spools with Case Rust and C o r r o s i o n P r eve n t a t i ve ( Pa r t Number B17510).

13. Charge the batteries. Remove the batteries from the machine and put the batteries on a wooden pallet in a cool dry area. If possible, keep the batteries in a building where the temperature is above freezing (0°C [32°F]). Make sure the batteries are clean.

NOTE: Always wear face protection when checking batteries. Check the batteries periodically for the correct electrolyte level. Test the electrolyte with a hydrometer. When the hydrometer reading is near 1.215, charge the batteries.

221

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE (First)

TRIM THIS EDGE

If the machine is to be in storage for more than 30 days, park the machine inside a building. If a building is not available, park the machine in a dry area on planks and cover the machine with a waterproof covering.

9. Change the engine oil and replace the oil filter.

MACHINE STORAGE

Removal from Storage 9. Use petroleum base solvent and remove the Case Rust and Corrosion Preventive from the hydraulic cylinder rods.

Do not start the engine until steps 1 through 10 have been done.

1. Change the fuel filter.

2. Put coolant in the engine cooling system.

3. Check the condition of the drive belts. Replace if required.

10. See Battery Service in this manual and install the batteries.

11. Fill the fuel tank.

12. Prime the turbocharger with clean e n g i n e o i l . S e e yo u r S e r v i c e Manual or your dealer.

4. Check the engine oil level.

5. Check the hydraulic oil level.

13. Start the engine. Allow the engine to r un seve ral mi nutes befor e placing a load on the engine.

6. Check the transmission oil level.

7. Check the oil level of both axles.

8. Lubricate the machine at all grease fittings.

TRIM THIS EDGE 222

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

SPECIFICATIONS

Make and model ................................................... Case 667TA/E2 Tier II Certified Air Induction ........................................................... Turbocharged and After cooled Bore and stroke ........................................................ 104 x 132 mm (4.09” x 5.20”) Displacement .....................................................................6.8 Liters (411 cu inch) Compression ratio ..................................................................................... 17.5 to 1 Horsepower SAE gross ....................................135 kW at 2000 r/min (181 hp @ 2000 rpm) SAE net ....................................... 127 kW at 2000 rpm (170 hp @ 2000 rpm) Engine speeds Idle speed ...................................................................................770 - 830 rpm *Hydraulic Stall .......................................................................1895 - 2205 rpm *Converter Stall ..................................................................... 1990 - 2145 rpm *Combined Hydraulic and Converter Stall ............................. 1706 - 2010 rpm *See Stall Speed Checking Procedure on Page 224.

Valve Clearance (Engine Cold) Intake Valves ............................................................... 0.250 mm (0.010 inch) Exhaust Valves ............................................................. 0.500 mm (0.020 inch)

TRAVEL SPEEDS with 20.5R25 XHA Tires, 50/40 PSI FIRST Forward

SECOND

THIRD

km/h

(mph)

km/h

(mph)

km/h

(mph)

km/h

(mph)

7.6

4.7

13.4

8.3

24.6

15.3

38.2

23.7

Buckets DESCRIPTION

WIDTH

CAPACITIES SAE Heaped m3

yd3 (3.00)

General Purpose

2700 mm (106.3 in)

2.29

General Purpose

2700 mm (106.3 in)

2.48

(3.25)

Material Handling

2700 mm (106.3 in)

2.68

(3.50)

2.29

(3.00)

XT Attachment

FOURTH

2700 mm (106.3 in)

223

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE (First)

TRIM THIS EDGE

ENGINE DATA 721D

SPECIFICATIONS

*Stall Speed Checking Procedures: (See Note) 1. Converter Stall. Values are read with the transmission in 3rd gear, auto shift off and engine at Wide Open Throttle.

2. Hydraulic Stall. Values are read while the lift arms are raising with the bucket held rolled back and the engine at Wide Open Throttle.

3. Converter & Hydraulic Stall. Values are read with the transmission in 3rd gear, auto shift off, while lift arms are raising with the bucket held rolled back and the engine at Wide Open Throttle.

NOTE: Torque converter and hydraulic oil must be warmed to normal operation temperatures before the Stall Speeds are checked. (See procedures below) A. Torque converter oil warming information: Torque Converter oil temperature should be between 82 to 104 degrees C, (180 to 220 degrees F).

TRIM THIS EDGE

Procedure to warm the Torque converter oil: (a) Deactivate the declutch switch. (b) Apply the parking brake. (c) shift the transmission into 3rd gear forward. (d) Run engine at Wide Open Throttle until the cluster displays a temperature of 115 degrees C, (240 degrees F). (e) Reduce engine speed to low idle. (f) Put the transmission into neutral, keep the parking brake engaged. (g) Wait until the converter temperature cools to 90 degrees C, (194 degrees F). (h) Repeat steps (c through g) three times.

B. Hydraulic oil warming information: Hydraulic oil temperature should be between 54 to 57 degrees C, (130 to 135 degrees F).

Procedure to warm the Hydraulic oil: (a) Apply the parking brake. (b) Run the engine at Wide Open Throttle. (c) Hold the bucket control in the rollback position. (d) Hold the lift control in the float position. (e) Continue until the temperature range is reached.

224

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

SPECIFICATIONS

OPERATING DATA AND DIMENSIONS

A D B G

F

E B0769A88

721D, Z-Bar Machines with 2.29 m3 (3.00 yd3) General Purpose Bucket and Standard Counterweight

A. B. C. D. E. F. G.

Tipping load, machine straight........................................ 14 472 kg (25 291 lb) Tipping load, 40 degree turn............................................. 9 985 kg (22 014 lb) Overall operating height, fully raised ................................ 5 171 mm (203.6 in) Height to bucket hinge pin, fully raised ........................... 3 982 mm (156.8 in) Dump height, 45 degree dump, full height ....................... 2 964 mm (116.7 in) Dump angle at full height ................................................................ 55 degree Bucket reach, 45 degree dump, full height ....................... 1 085 mm (42.7 in) Wheel Base ...................................................................... 3 253 mm (128.1 in) Overall Length .................................................................. 7 595 mm (299.0 in) Overall height to top of ROPS cab.................................... 3 349 mm (131.8 in)

Specifications taken with 20.5 R25 XHA tires, ROPS cab with heater and air conditioning, 1 016 kg (2 237 lb) standard rear counterweight, fenders, standard batteries, lamps, full fuel tank, and a 80 kg (175 lb) operator.

225

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

C

SPECIFICATIONS

OPERATING DATA AND DIMENSIONS

A D B G C

TRIM THIS EDGE

F

E B0769A88

721D, Z-Bar Machines with 2.48 m3 (3.25 yd3) General Purpose Bucket and Optional Counterweight

A. B. C. D. E. F. G.

Tipping load, machine straight ..................................... 12 757 kg (28 125 lbs) Tipping load, 40 degree turn ........................................ 11 067 kg (24 399 lbs) Overall operating height, fully raised ............................... 5 229 mm (205.9 in) Height to bucket hinge pin, fully raised ........................... 3 980 mm (156.7 in) Dump height, 45 degree dump, full height ...................... 2 931 mm (115.4 in) Dump angle at full height ................................................................ 55 degree Bucket reach, 45 degree dump, full height ....................... 1 126 mm (44.3 in) Wheel Base ...................................................................... 3 253 mm (128.1 in) Overall Length .................................................................. 7 648 mm (301.1 in) Overall height to top of ROPS cab.................................... 3 347 mm (131.8 in)

Specifications taken with 20.5 R25 XHA tires, ROPS cab with heater and air conditioning, 1 571 kg (3 460 lb) optional rear counterweight, fenders, standard batteries, lamps, full fuel tank, and a 80 kg (175 lb) operator.

226

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

SPECIFICATIONS

OPERATING DATA AND DIMENSIONS

A D B G

E F

721D, Z-Bar Machines with 2.48 m3 (3.25 yd3) Material Handling Bucket and Standard Counterweight A. B. C. D. E. F. G.

Tipping load, machine straight ......................................11 444 kg (25 229 lbs) Tipping load, 40 degree turn .......................................... 9 955 kg (21 948 lbs) Overall operating height, full raised .................................. 5 231 mm (205.9 in) Height to bucket hinge pin, fully raised ........................... 3 981 mm (156.7 in) Dump height, 45 degree dump, full height ....................... 2 931 mm (115.4 in) Dump angle at full height ................................................................ 55 degree Bucket reach, 45 degree dump, full height ........................ 1 125 mm (44.3 in) Wheel Base ..................................................................... 3 253 mm (128.1 in) Overall Length ................................................................. 7 645 mm (301.0 in) Overall height to top of ROPS cab.................................... 3 349 mm (131.8 in)

Specifications taken with 20.5 R25 XHA tires, ROPS cab with heater and air conditioning, 1 016 kg (2 237 lb) standard rear counterweight, fenders, standard batteries, lamps, full fuel tank, and a 80 kg (175 lb) operator.

227

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

C

SPECIFICATIONS

OPERATING DATA AND DIMENSIONS

A D B G C

TRIM THIS EDGE

F

E BS04F174

721D, XT Machines with 2.30 m3 (3.00 yd3) ACS PRO 2000 General Purpose bucket and Standard Counterweight A. B. C. D. E. F. G.

Tipping load, machine straight.......................................11 353 kg (25 029 lbs) Tipping load, 40 degree turn............................................9 790 kg (21 583 lbs) Overall operating height, fully raised ................................ 5 536 mm (217.9 in) Height to bucket hinge pin, fully raised ............................. 4 160 mm (163.8 in) Dump height, 45 degree dump, full height........................ 2 933 mm (115.5 in) dump angle at full height .................................................................. 55 degree Bucket reach, 45 degree dump, full height ......................... 1 278 mm (50.3 in) Wheel base....................................................................... 3 253 mm (128.1 in) Overall length.................................................................... 7 916 mm (311.7 in) Overall height to top of ROPS cab................................... 3 345 mm ( 131.7 in)

Specifications taken with 20.5 R25 XHA tires, ROPS cab with heater and air conditioning, 1 016 kg (3 460 lbs) standard rear counterweight, fenders, standard batteries, lamps, full fuel tank, and a 80 kg (175 lb) operator.

228

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

SPECIFICATIONS

721D, XT Machines with ACS PRO 2000 Fork Option

TRIM THIS EDGE

Fork Tine Size........................................ 64 x 152 x 1 219 mm (2.5” x 6” x 48”) Maximum Fork Width ...................................................... 1 368 mm (53.8 inch) Maximum Fork Clearance................................................. 3 910 mm (153.9 in) Fork Reach at Full Height ...................................................... 922 mm (36.2 in) Fork Clearance at Maximum Reach ................................... 1 890 mm (74.4 in) Maximum Fork Reach......................................................... 1 753 mm (69.0 in) Fork Reach at Ground ....................................................... 1042 mm (41.0 in) Fork Load Center...................................................................... 610 mm (24 in) Weight (Forks and Coupler)..................................................834 kg (1 839 lbs) Operating Load (Firm and Level Ground) ....................... 5 454 kg (12 024 lbs) Operating Load (Rough Terrain) ........................................4 091 kg (9 081 lbs) Tipping Load (Straight) ................................................... 8 040 kg (17 725 lbs) Tipping Load (40 degree Turn) ........................................6 818 kg (15 034 lbs) Unit operating mass.......................................................13 906 kg (30 658 lbs)

229

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

SPECIFICATIONS

WEIGHTS - 721D Z-BAR Operating Weights with Machine Straight, Bucket Level On Ground 3.25 yd Bucket with edge

FRONT AXLE

REAR AXLE

TOTAL

6 157 kg (13 575 lbs)

7 999 kg (17 634 lbs)

14 156 kg (31 209 lbs)

WEIGHTS - 721D XT Operating Weights with Machine Straight, Bucket Level On Ground 3.0 yd Bucket with edge

FRONT AXLE

REAR AXLE

TOTAL

6 966 kg (15 358 lbs)

7 741 kg (17 066 lbs)

14 707 kg (32 424 lbs)

TRIM THIS EDGE

NOTE: Machine weights taken with 20.5 R25 XHATL Michelin tires; ROPS cab with heater and air conditioning; fenders; standard batteries; lamps; full fuel tank; 1 571 kg (3 460 lb) optional counterweight on Z-Bar (standard on XT); 79 kg (175 lb) operator and standard equipment.

Weight Adjustments for Optional Equipment 721D Z-Bar ITEM

POUNDS

(kg)

-100

-45

228

104

380

173

-295

-134

20.5 x 25, L2 20.5 x 25, L3 20.5 R 25 XHA ROPS Canopy

230

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

SPECIFICATIONS

SPECIAL BOLT TORQUES POUND-FOOT (44 to 52) (7.4 to 8.3)

(704 to 793) (480 to 500) (42 to 48) (52 to 58) (570 to 630) (7.4 to 8.3) (73 to 94) (830 to 933) (39 to 46) (39 to 46) (180 to 220) (87 to 98) (27 to 32) (27 to 32) (18 to 20) (52 to 58) (250 to 275) (177 to 225) (479 to 540) (17 to 20) (99 to 111) (25 to 32) (240 to 275) (479 to 540) (15 to 18) (7.4 to 8.3) (7.4 to 8.2) (214 to 277) (30 to 35) (656 to 738) (185 to 235) (355 to 435) (4) (45 to 60) (472 to 531)

NOTE: All bolt torques are listed with dry threads unless noted otherwise. * See Wheel Nut Torque in this manual. ** No Impact Tools *** Apply Loctite to screw threads and let dry for 70 seconds. Then apply Loctite 243 and torque to specified value.

231

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

Nm Alternator Pulley ** ............................................................. 60 to 70 Air Cleaner Hose ......................................................... 10.1 to 11.3 Articulation Mounting Pin Retainer Bolt .....................See ES-FA32 Articulation Pivot Pin Bolts ........................................See ES-FA32 Front Axle Mounting Bolts ............................................ 955 to 1075 Rear Axle Trunnion Pin Bolts ......................................... 651 to 678 Brake Pump to Engine Mounting ....................................... 57 to 65 Brake Pump Gear Nut ** .................................................... 70 to 79 Cab and Canopy Mounting Bolts (2) .............................. 773 to 854 CAC Hose Clamps ....................................................... 10.1 to 11.3 Carrier Bearing Mounting Bolts ........................................ 99 to 128 Counterweight Bolts ................................................ 1 125 to 1 265 Coupling to Flywheel ........................................................ 53 to 62 Drive Shaft to Coupling .................................................... 53 to 62 Engine (rubber isolation) Mounts (4) .............................. 244 to 298 Engine Mounting Brackets (4) ........................................ 118 to 133 Exhaust Stack to Hood Nuts ............................................. 36 to 44 Intake Stack to Hood Nuts.................................................. 36 to 44 Fan to Fan Coupler ........................................................... 24 to 27 Fan Coupler to Shaft ** ..................................................... 70 to 78 Front Drive Shaft Yoke Nut ............................................. 339 to 373 Guide Link Nuts (XT Only) ............................................. 240 to 305 Guide Loader Linkage Bolts (XT Only).......................... 650 to 732 Hydraulic Oil Filter Mounting Bolts .................................... 23 to 27 Hydraulic Pump to Transmission Mounting ................... 134 to 151 Hydraulic Tank Cover Bolt .................................................. 34 to 44 Loader Linkage Pin Keeper ........................................... 325 to 373 Loader Linkage Bolts, Grade 8 (XT Only) ...................... 650 to 732 Muffler to Turbo Elbow Clamp ............................................ 20 to 25 Radiator Hose Clamp - Radiator Side .......................... 10.1 to 11.3 Radiator Hose Clamp - Tube Side .............................. 10.1 to 11.1 Steering Wheel Retaining Bolts ................................... 290 to 375 Steering Wheel Retaining Nut............................................ 40 to 47 Transmission (rubber isolation) Mounts ....................... 890 to 1000 Transmission Upper Mounting Bracket Bolts ................. 251 to 319 Transmission Lower Mounting Bracket Bolts (2) ............ 481 to 590 Turbo to Turbo Elbow Clamp ........................................................ 5 550R Universal Joints. ....................................................... 61 to 81 Wheel Mounting Bolts ................................................... 640 to 720

SPECIFICATIONS

NOTES

TRIM THIS EDGE 232

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

38

A Access Doors ................................ 147 Accumulators, Brake ..................... 121 After Delivery Check ............. 239, 241 Air Conditioning Compressor .............................. 191 Compressor Belt ....................... 210 Compressor Seal Lubrication .... 191 Condenser ................................ 191 Indicator ...................................... 49 Temperature Control ................... 83 Air Filter Cab ........................................... 187 Cleaning .................................... 167 Indicator ...................................... 50 Primary Element ....................... 166 Replacement ............................. 165 Secondary Element ................... 166 Service Specifications ............... 164 System ...................................... 164 Air Louvers, Cab ............................. 90 Alternator Belt ............................... 210 Autoshift Switch ............................... 84 Auxiliary Hydraulic Connection ................................ 122 System Specifications ............... 122 Auxiliary Power Equipment Mounting Bracket .... 219 Outlet ........................................ 218 Axle Oil Change ................................ 185 Oil Level .................................... 183 Service Specifications ............... 183

B Battery Cleaning .................................... 214 Cold Weather Operations ......... 130 Connection, Booster ................. 104 Fluid Level ................................. 214 Safety ........................................ 213 Service ...................................... 213

Vents ......................................... 214 Beacon Indicator ............................. 43 Before Operation Safety Message .. 12 Before Starting The Engine ............. 99 Belt Air Conditioning Compressor .... 210 Alternator .................................. 210 Fan ............................................ 210 Seat ............................. 97, 100, 206 Blower Fan Switch .......................... 80 Bolt Torques .................................. 229 Booster Battery Connection .......... 104 Brake Parking, Check .......................... 198 Parking, Switch ........................... 41 Parking,Holding ......................... 107 Pedals ......................................... 74 Pressure Indicator ....................... 44 Service, Holding ........................ 107 Brake Accumulators ...................... 121 Bucket Height Control Function ................................ 119 Minor Adjustment .................. 205 Bucket Level Indicator ................... 122 Bulbs, Replacement .............. 217, 220 Burn Prevention Safety Message .... 15

C Cab ................................................ 192 Air Filter ..................................... 187 Cleaning ............................... 188 Removal and Installation ...... 187 Cab Headliner ........................... 192 Door Hinges .............................. 192 Hoses and Wiring ...................... 192 Operators Seat .......................... 193 Service ...................................... 191 Caution Master Indicator ................. 47 Charts Hydraulic System Fluid ............. 175 Lubrication ................................ 146 Maintenance ............................. 146 Clutch Calibration

231

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE (First)

TRIM THIS EDGE

INDEX

INDEX

TRIM THIS EDGE

Main Codes ................................196 Sub-Codes .................................196 Transmission .............................195 Cold Weather Starting ....................130 Components, Machine .......................7 Conditioner, Fuel ............................171 Console Front ......................................37, 38 Side ..........80, 81, 82, 83, 84, 85, 86 Controls Air Conditioning Temperature ......83 Blower Fan ...................................80 Hand ......................................37, 38 Heat, Cab .....................................80 Lamp Switch ................................82 Steering Wheel Tilt ......................40 Wiper/Washer Switch ..................81 Coolant Fluid Level .................................169 Cooling System Cleaning .....................................170 Cold Weather Operations ..........130 Coupler Pin Engagement Switch ..........................................86

D Declutch Switch ...............................83 Declutch ..........................................121 Defrost Air Louvers ..........................92 Detent On/Off Switch .......................83 Diesel Fuel System ........................171 Disabled Machine Towing ..............127 Display Center Lamp, Setting ...............................69 Transmission ...................71, 72, 73 Displays, Warning Non - Critical Warning Displays ...47 Do Not Operate Tag .........................18 Door Access .......................................147 Hinges ........................................192 Latch ............................................93 Dust Valve ......................................165

E Electrical System ...........................213 Emergency Exit ................................98

ENGINE .......................................... 38 Engine Data .................................. 223, 225 Hourmeter ................................. 144 Lubrication ................................ 159 Service Specification ................ 161 Specifications .................... 223, 225 Speed ....................................... 102 Engine Coolant Cleaning the Cooling System ... 170 Fluid Level ................................ 169 Gauge ......................................... 56 Heater ....................................... 103 Mixture ...................................... 168 Engine Cooling System Coolant Mixture ......................... 168 Service Specifications ............... 168 Specifications ............................ 168 Thermostat ................................ 168 Engine Data .................................. 223 Engine Oil Change ..................................... 162 Filter .......................................... 162 Heater ....................................... 103 Level ......................................... 161 Pressure Gauge ........................ 162 Selection ................................... 159 Exit Emergency .................................. 98 Extinguisher Mounting, Fire .......... 211

F Fan Belt ......................................... 210 Fan Reverser (option) ..................... 86 Filter Air ............................................. 166 Cab Air ...................................... 187 Engine Oil ................................. 162 Fuel ........................................... 174 Hydraulic Oil ............................. 177 Transmission Oil ....................... 181 Filter Replacement Air ............................................. 165 Engine Oil ................................. 162 Hydraulic Oil ............................. 177 Transmission Oil ....................... 181

232

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

INDEX Fuel Conditioner ........................ 171 Fuel Filter .................................. 174 Fuel Storage ............................. 172 Removing Water ....................... 173 Service Specifications ............... 171 Fuse Panel .................................... 216 Fuses ............................................ 216

G Gauge Displays 64, 65, 66, 67, 68, 69, 70 Programming .............................. 65 Gauges Engine Coolant ........................... 56 Fuel Level ................................... 54 HydraulicOil Temperature ........... 52 Transmission Oil Temperature .... 51 Volt Meter .................................... 53 General Safety .............................. 139 Grease Fittings 100 Hours XT Linkage ........................... 154 Z-Bar Linkage ....................... 150 1000 Hours Z-Bar Linkage ....................... 152 50 Hours XT Linkage ........................... 153 Z-Bar Linkage ....................... 149 Grid Heater .................................... 130

H Hand Signals ................................... 34 Heat Control, Cab ........................... 80 Hood Switch .................................... 89 Horn ................................................ 40 Hoses and Wiring .......................... 192 Hot Weather Operation ................. 132 Hourmeter, Engine ........................ 144 Hydraulic Connection - Auxiliary ... 122 Hydraulic Filter Test ...................... 177 Hydraulic Oil Filter .......................................... 177 Filter Indicator ............................. 50 Temperature Gauge .................... 52 Hydraulic System Filter Replacement .................... 177 Fluid Chart ................................ 175

233

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

Fire Extinguisher Mounting ........... 211 Fire Extinguisher Safety Message .. 16 Fire or Explosion Safety Message .. 17 First Service Intervals .................... 100 Fittings, Grease 100 Hours XT Linkage ........................... 154 Z-Bar Linkage ....................... 150 1000 Hours Z-Bar Linkage ....................... 152 50 Hours XT Linkage ........................... 153 Z-Bar Linkage ....................... 149 Float .............................................. 120 Fluid and Lubricants 145 Fluid Levels ................................... 155 10 Hours ................................... 155 50 Hours ................................... 156 Coolant ...................................... 169 Engine Coolant ......................... 169 Radiator .................................... 169 Foot Pedals Brake Pedals ............................... 74 Foot Throttle ................................ 74 Four-Way Flasher Lamp ........................................... 43 Switch ......................................... 37 Front Console ............................ 37, 38 Four-Way Flasher ....................... 37 Horn ............................................ 40 Key/Ignition Switch ...................... 42 Park Brake Switch ....................... 41 Pilot Control Switch ..................... 37 Program/Reset Switch ................ 37 Steering Wheel Tilt Control ......... 40 Transmission Control Lever ........ 39 Turn Signal .................................. 40 Up/Down Count Switch ............... 37 Fuel Conditioner ............................ 171 Fuel Filter ...................................... 174 Fuel Level Gauge ............................ 54 Fuel Storage .................................. 172 Fuel System Cold Weather Operations ......... 130 Diesel Fuel Specifications ......... 172

INDEX Hydraulic Filter Test ...................177 Service Specifications ................175

Stop Master ............................ 45 Transmission Oil Filter ............ 50 Turn Signal ............................. 43

I

TRIM THIS EDGE

Identification Numbers .......................5 Indicator Air Conditioning ...........................49 Air Filter .......................................50 Beacon .........................................43 Brake Pressure ............................44 Caution Master ............................47 Hydraulic Oil Filter .......................50 Lamp ............................................44 Low Coolant .................................44 Parking Brake ..............................49 Pilot Lockout ................................44 Secondary Steering Master .........49 Stop Master .................................45 Transmission Oil Filter .................50 Indicator Lamps 43, 44, 45, 47, 49, 50, 51, 52, 53, 54, 55, 56, 57 Information Center ..58, 59, 60, 61, 62, 63 Programming ...............................59 Instructions, General Safety ...........139 Instrument Panel 43, 44, 45, 47, 49, 50, 51, 52, 53, 54, 55, 56, 57 Indicator Gauges Engine Coolant ........................56 Fuel Level ................................54 Hydraulic Oil Temperature ......52 Transmission Oil Temperature 51 Volt Meter ................................53 Indicator Lamps Air Conditioning .......................49 Air Filter ...................................50 Brake Pressure ........................44 Caution Master ........................47 Four-Way Flasher ....................43 Hydraulic Oil Filter ...................50 Lamp Indicator .........................44 Low Coolant ............................44 Parking Brake ..........................49 Pilot Lockout ............................44 Rotating Beacon ......................43 Secondary Steering .................49

J Jump Start ..................................... 104

K Key Switch, Ignition ......................... 42

L Lamp Four-Way Flasher ....................... 43 Turn Signal ................................. 43 Lamp Indicator ................................ 44 Lamp Switch, Cab ........................... 82 Latch Door ............................................ 93 Window ....................................... 93 Window Retainer ........................ 94 Levers Transmission Control .................. 39 Turn Signal ................................. 40 Link Safety ........................................ 141 Transport .................................. 141 Loader Adjustments Return-To-Dig ........................... 194 Loader Function Switches ............. 118 Loader Operating Tips .................. 125 Leveling Operation .................... 125 Pushing Operation .................... 125 Scraping Operation ................... 125 Transport and Carry Operation . 126 Loader Operations Cold Weather ............................ 130 Louvers, Air Defrost ........................................ 92 Recirculation ............................... 90 Low Coolant Indicator ..................... 44 Lubrication Analysis, Systemgard . 163 Lubrication Chart ........................... 146 Lubrication, Engine ....................... 159

M Machine Components ....................... 7 Machine Operation

234

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

Before Operating ....................... 106 Transmission Operation ............ 109 Machine Operation Safety Message ...

13, 15, 16, 17, 18, 19 Machine Storage ........................... 221 Removal .................................... 222 Storage Preparation .................. 221 Machine Tie Down Locations ........ 129 Machines ....................................... 226 Maintenance and Inspection of ROPS 206 Maintenance Chart ........................ 146 Maintenance Safety Message ......... 18 Master Disconnect Switch ............... 88 Material Safety Data Sheets ........... 18 MSDS Sheets .................................. 18

O Oil Change 185 Engine ....................................... 162 Oil Level Axle ........................................... 183 Engine ....................................... 161 Transmission ............................. 181 Oil Selection, Engine ..................... 159 Oil Viscosity/Temperature Ranges 160 Operating Data ...................... 224, 225 226 Operating Dimensions ................... 224 225, 226 Operating In Hot Weather ............. 132 Operating Instructions ..................... 99 Before Starting The Engine ......... 99 Operating The Machine ................. 106 Operating Tips - Loader ................ 125 Operator Manual Storage Compartment ..................................................... 3 Operators Manual, Read ................. 20 Operators Seat ........................ 94, 193 Owner, To The .................................. 1

P Parking Brake Check ........................................ 198 Holding Check ........................... 107

Indicator ...................................... 49 Switch ......................................... 41 Parking The Machine .................... 102 Parking the Machine Safety Message .

15 Pedals, Foot .................................... 74 Personal Safety Rules Message ..... 11 Pilot Control Switch ......................... 37 Pilot Lockout Indicator ..................... 44 Plastic and Resin Parts ................. 142 Power Outlet, Auxiliary .................. 218 Pressure, Tire ................................ 133 Primary Element, Air Filter ............ 166 Product Identification Number ........... 5 Program/Reset Switch ..................... 37 Programming Display Center Lamp, Setting ..... 69 Gauge Display ............................ 65 Information Center ...................... 59

R Radiator Fluid Level ................................. 169 Radio ............................................... 93 Read Operators Manual .................. 20 Rear Fog Lamp Switch .................... 85 Rear Wiper/Washer Switch ............. 84 Reservoir, Windshield Washer ...... 189 Return-To-Dig Adjustment ................................ 194 Function .................................... 118 Return-To-Travel ........................... 119 Switch ......................................... 83 Ride Control .................................. 123 Switch ......................................... 84 Roll-Over Protective Structure ....... 206 Roll-Over Protective Structure Safety Message ................................... 19 ROPS ............................................ 206 Damage Information ................. 208 Maintenance and Inspection ..... 206 Seat Torque Specifications ........... 209 Seat Belt ................................... 206 Torque Specifications ........... 209 Specifications

235

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

INDEX

INDEX Canopy Torque ......................207 Cap Torque ...........................207 Rotating Beacon ............................123 Switch ..........................................85 Run-In Procedure .............................99

TRIM THIS EDGE

Air Conditioning Temperature ..... 83 Autoshift Switch .......................... 84 Blower Fan Switch ...................... 80 Coupler Pin Engage Switch ........ 86 Declutch Switch .......................... 83 Detent On/Off Switch .................. 83 S Heat Control ................................ 80 Safety Decals ...................................20 Lamp Switch ............................... 82 Safety Instructions, General ...........139 Rear Fog Lamp Switch ............... 85 Safety Link, Service .......................141 Rear Wiper/Washer Switch ......... 84 Safety Rules .......................................9 Return-To-Travel Switch ............. 83 Hand Signals ...............................34 Ride Control Switch .................... 84 Utility ............................................10 Rotating Beacon Switch .............. 85 Safety, Battery ...............................213 Wiper/Washer Switch ................. 81 Safety/Decals/Hand Signals ..............9 Wrist Rest ................................... 80 Before Operation .........................12 Wrist Rest, Adjustment ............... 80 Burn Prevention ...........................15 Specifications ................................ 223 Fire Extinguisher ..........................16 Air Filter .................................... 164 Fire or Explosion ..........................17 Auxiliary Hydraulic System ....... 122 Machine Operation ...13, 15, 16, 17, Axle ........................................... 183 18, 19 Cooling System, Engine ........... 168 Maintenance ................................18 Diesel Fuel System ................... 171 Parking the Machine ....................15 Dimensions Personal Safety ...........................11 224, 225, 226 Read Operators Manual ..............20 Engine Cooling System ............ 168 Roll-Over Protective Structure .....19 Engine Data ...................... 223, 225 Safety Decals ...............................20 Engine Service .......................... 161 Wheel and Tire Maintenance .......19 Fuel System .............................. 171 Seat Hydraulic System ...................... 175 Belts .............................97, 100, 206 Machines Inspection and Care ................98 ACS PRO 2000 Bucket ........ 225 Operators .............................94, 193 General Purpose Bucket ...... 225 Optional Air Ride ..........................95 Operating Data ................. 225, 226 Standard ......................................94 224 Torque Specifications ................209 ROPS Torque ........................... 207 Seat Belt Seat Belt Torque ....................... 209 Torque Specifications ................209 Seat Torque .............................. 209 Secondary Element, Air Filter ........166 Thermostat ................................ 168 Secondary Steering Master Indicator ...

Transmission ............................ 180 49 Travel Speeds ........................... 223 Sediment Removal, Fuel System ...173 XT Machines Serial Numbers ..................................5 ACS PRO 2000 Fork Option . 227 Service Connector .........................218 Starting The Engine ...................... 101 Service Intervals - First ..................100 Steering Wheel Tilt Control ............. 40 Service Safety Link ........................141 Steering, Secondary ...................... 197 Service,Holding ..............................107 Stop Master Indicator ...................... 45 Side Console 80, 81, 82, 83, 84, 85, 86 Stopping The Engine ..................... 102 236

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

Storage Compartment Operator Manual ........................... 3 Storage, Fuel ................................. 172 Storage, Machine Preparation ............................... 221 Removal .................................... 222 Switch Autoshift ...................................... 84 Blower Fan .................................. 80 Coupler Pin Engage .................... 86 Declutch ...................................... 83 Detent On/Off .............................. 83 Four-Way Flasher ....................... 37 Key/Ignition ................................. 42 Lamp ........................................... 82 Loader Function ........................ 118 Bucket Height Control ........... 119 Float ...................................... 120 Return-To-Travel .................. 119 Master Disconnect ...................... 88 Park Brake .................................. 41 Pilot Control ................................ 37 Program/Reset ............................ 37 Rear Fog Lamp ........................... 85 Rear Wiper/Washer .................... 84 Return-To-Travel ......................... 83 Ride Control ................................ 84 Rotating Beacon ......................... 85 Up/Down Count ........................... 37 Wiper/Washer ............................. 81 Systemgard Analysis ..................... 163

Cold Oil Level Check ................ 181 Control Lever .............................. 39 Display Center ................ 71, 72, 73 Filter Replacement .................... 181 Oil Change ................................ 181 Oil Level .................................... 181 Operation of .............................. 109 Service Specifications ............... 180 Warm Oil Level Check .............. 181 Transmission Oil Filter .......................................... 181 Filter Indicator ............................. 50 Level ......................................... 181 Check ................................... 181 Temperature Gauge .................... 51 Transmission Operation Automatic Mode Operation ....... 109 Down-Shift Button, Manual Mode ...

109 Down-Shifts Manual Mode ........ 109 Manual Mode Operation ........... 109 Shifting, Automatic Mode .......... 110 Up-Shifts Manual Mode ............ 109 Transport Link ............................... 141 Transporting The Machine ............ 128 On A Trailer ............................... 129 Travel Speeds 223 Turn Signal Lamp ........................................... 43 Lever ........................................... 40

T

U

Thermostat Specifications ............. 168 Throttle, Foot ................................... 74 Tire Or Rim Service ....................... 135 Tire Pressure ................................. 133 Tire Tread Direction ...................... 135 Tires, Adding Air ............................ 135 Torque - Wheel Nut ....................... 136 Towing, Machine ........................... 127 Transmission Breather Cleaning ..................... 181 Clutch Calibration ...................... 195 Clutch Calibration Main Codes . 196 Clutch Calibration Sub-Codes ... 196

Up/Down Count Switch ................... 37 Utility Safety .................................... 10

V Volt Meter Gauge ............................ 53

W Warning Displays Non - Critical Warning Displays .. 47 Water Removal, Fuel System ........ 173 Weights Adjustments, Optional Equipment 228 Wheel and Tire Maintenance Safety

237

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

INDEX

INDEX Message ....................................19 Wheel And Tires ............................133 Wheel Nut Torque ..........................136 Window Latch ............................................93 Retainer Latch .............................94 Windshield Washer Reservoir ........189 Wiper/Washer Switch .......................81 Wrist Rest ........................................80 Adjustment Knob .........................80

TRIM THIS EDGE 238

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

AFTER DELIVERY CHECK AFTER FIRST 100 HOURS OF OPERATION OF NEW MACHINE

Owners Name: Address: Dealers Name: Address: Hourmeter Indication:

Machine Model Number: Machine Product Identification Number (P.I.N.): COOLING SYSTEM

HYDRAULIC SYSTEM

Check the coolant levels.

Check the oil level.

Check for leaks.

Check the pressure setting of the main relief valve.

Replace the hydraulic oil filter.

FUEL SYSTEM

GENERAL

Drain water and sediment from the fuel tanks.

Look for oil leaks and loose parts.

Check tire pressure.

ELECTRICAL SYSTEM Check battery.

Tighten all hose clamps.

Check operation of starter, alternator, and instruments.

Check drive chain tension.

Check operation of all lamps.

Check brake operation.

Check wheel nut torque.

LUBRICATION

Check the control levers for correct operation.

Check the operators seat bar for correct operation.

Lubricate all pivot points.

Engine SAFETY

Check condition of drive belt.

Check engine oil level.

Inspect the ROPS.

Check engine speed at idle and at full throttle.

Check the safety decals and replace if necessary.

Service air cleaner.

Check the operator restraint system.

Make sure the machine has the operators manual in the manual storage box.

DEALER: Make sure the owner and/or operator understands all the safety and information decals, the service information, and the service procedures in this manual.

Technician Signature: Dealer Signature: Owner Signature: Dealer Copy

239

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE (First)

TRIM THIS EDGE

Check for leaks.

TRIM THIS EDGE 240

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

AFTER DELIVERY CHECK AFTER FIRST 100 HOURS OF OPERATION OF NEW MACHINE

Owners Name: Address: Dealers Name: Address: Hourmeter Indication:

Machine Model Number: Machine Product Identification Number (P.I.N.): ENGINE

HYDRAULIC SYSTEM

Check the engine oil level.

Check for leaks.

Check air cleaner.

Tighten all hose clamps.

Check the reservoir oil level.

COOLING SYSTEM

GENERAL

Check the coolant level of radiator and coolant reservoir.

FUEL SYSTEM

Check the operation of the brakes.

Check the control levers for correct operation.

SAFETY

Check for leaks.

Check the safety and information decals.

Drain water and sediment from the fuel tanks.

Check the torque of ROPS and seat belt mounting bolts.

ELECTRICAL SYSTEM

Make sure the Operator’s Manual and Safety Manual are in the Manual Storage Box.

Check operation of starter, alternator, and instruments.

Check operation of all lamps.

LUBRICATION Lubricate all pivot points.

Check oil level of final drives.

Check transmission oil level.

DEALER: Make sure the owner and/or operator understands all the safety and information decals, the service information, and the service procedures in this manual.

Technician Signature: Dealer Signature: Owner Signature: Owner Copy

241

TRIM THIS EDGE Bur 6-35092na RIGHT PAGE

TRIM THIS EDGE

Tighten all hose clamps.

TRIM THIS EDGE 242

TRIM THIS EDGE Bur 6-35092na LEFT PAGE

CASE TECHNICAL MANUALS Manuals are available from y our Dealer for the operation, service and repair of your ma chine. For prompt convenient service, contact your Dealer fo r assistance in obtaining the manuals for your machine.

Your Dealer can expedite your order for operators manuals, parts catalogs, service manua ls and maintenance records.

Always give the Machine Name , Model and P.I.N. (product identification number) or S.N. (s erial number) for your machine so your Dealer can provide the correct manuals for your machine.

CALIFORNIA Proposition 65 Warning Diesel engine exhaust and some of its constituents are known to the State of California to cause cancer, birth defects, and ot her reproductive harm.

Battery post, terminals and related accessories contain lead and lead compounds. Wash hands after handling.

NOTE: Case Corporation reserves the right to make improvements in design or changes in specifications at any time without incurring any obligation to install them on units previously sold.