Case 450 450CT 465 Skid Steer Loader Compact Track Loader Operator's Manual 87364592 - PDF DOWNLOAD

OPERATOR’S MANUAL

SKID STEER COMPACT TRACK LOADER 450 450CT 465

87364592 NA Replaces 6-82092 NA

Revised 01-2007 Issued 08-2005

450 450CT 465 SKID STEER LOADER COMPACT TRACK LOADER

Issued January, 2007 Book/Form Number 87364592 NA • Printed in U.S.A. • Bur Copyright © 2007. CNH America, LLC. All Rights Reserved.

TRIM THIS EDGE Title Page - Right-Hand Page (First Page) Bur 87364592

TRIM THIS EDGE

OPERATOR’S MANUAL

THIS SAFETY ALERT SYMBOL INDICATES IMPORTANT SAFETY MESSAGES IN THIS MANUAL. WHEN YOU SEE THIS SYMBOL, CAREFULLY READ THE MESSAGE THAT FOLLOWS AND BE ALERT TO THE POSSIBILITY OF DEATH OR SERIOUS INJURY M171D

Safety Decals on this machine use the words Danger, Warning, or Caution, which are defined as follows:

• DANGER:

Indicates an immediate hazardous situation that, if not avoided, will result in death or serious injury. The color associated with Danger is RED.

• WARNING:

Indicates a potentially hazardous situation that, if not avoided, could result in death or serious injury. The color associated with Warning is ORANGE.

• CAUTION:

Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices. The color associated with Caution is YELLOW.

If Safety Decals on this machine are ISO two panel Pictorial, decals are defined as follows:

TRIM THIS EDGE

• • • •

The first panel indicates the nature of the hazard.

The second panel indicates the appropriate avoidance of the hazard.

Background color is YELLOW Prohibition symbols such as

and

STOP

if used, are RED.

IMPROPER OPERATION OF THIS MACHINE CAN CAUSE DEATH OR SERIOUS INJURY. BEFORE USING THIS MACHINE, MAKE CERTAIN THAT EVERY OPERATOR: • Is instructed in safe and proper use of the machine.

• Reads and understands the Manual(s) pertaining to the machine.

• Reads and understands ALL Safety Decals on the machine.

• Clears the area of other persons.

• Learns and practices safe use of machine controls in a safe, clear area before operating this machine on a job site.

It is your responsibility to observe pertinent laws and regulations and follow the manufacture’s instructions on machine operation and maintenance.

CALIFORNIA PROPOSITION 65 WARNING Diesel engine exhaust and some of its constituents are known to the State of California to cause cancer, birth defects, and other reproductive harm.

Battery post, terminals and related accessories contain lead and lead compounds.

Wash hands after handling.

TRIM THIS EDGE Title Page - Left-Hand Page (Second Page) Bur 87364592

TO THE OWNER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 RIGHT, LEFT, FRONT AND REAR OF MACHINE . . . . . . . . . . . . . . . . . . 3 PRODUCT IDENTIFICATION AND SERIAL NUMBERS . . . . . . . . . . . . . . 4 MACHINE COMPONENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 UTILITY SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 PERSONNEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 PROPER ENTRY AND EXIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 STARTING AND STOPPING PRECAUTIONS . . . . . . . . . . . . . . . . . . . . 14 OPERATING PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 MAINTENANCE PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 FUEL HANDLING PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 BURN PREVENTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 HAZARDOUS CHEMICAL PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . 19 TRANSPORTING PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 ROLL-OVER PROTECTIVE STRUCTURE . . . . . . . . . . . . . . . . . . . . . . . 20 FIRE EXTINGUISHER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 SEAT BELT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 SPECIFIC PRECAUTIONS TO THIS MACHINE . . . . . . . . . . . . . . . . . . . 22 450 LOADER LIFT ARM SUPPORT STRUT . . . . . . . . . . . . . . . . . . . . . . 24 EMERGENCY EXIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 SAFETY DECALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 INSTRUMENTS AND CONTROLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 BATTERY MASTER DISCONNECT SWITCH . . . . . . . . . . . . . . . . . . . . . . . 49 STEERING AND TRAVEL WITH H PATTERN CONTROLS . . . . . . . . . . 50 STEERING AND TRAVEL WITH H PATTERN CONTROLS . . . . . . . . . . 51 LIFT ARM AND BUCKET CONTROL WITH ISO PATTERN PILOT CONTROLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 THROTTLE CONTROLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 LIFT ARM HYDRAULIC BYPASS CONTROL . . . . . . . . . . . . . . . . . . . . . . . 62 AUXILIARY HYDRAULIC ATTACHMENT CONTROL PEDAL . . . . . . . . . . 64 AUXILIARY ELECTRO-HYDRAULIC CONTROLS (If Equipped) . . . . . . . . . 67 OPERATOR’S SEAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 SLIDING SIDE WINDOWS (IF EQUIPPED) . . . . . . . . . . . . . . . . . . . . . . . . . 71 WINDSHIELD WASHER CONTROLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 OPERATING INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

DAILY INSPECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

STARTING THE ENGINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

PARKING THE MACHINE AND STOPPING THE ENGINE . . . . . . . . . .

RUN-IN PERIOD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

OPERATING IN COLD WEATHER . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

I

TRIM THIS EDGE RIGHT PAGE (Chapter First Page) Bur 87364592na

75 75 78 79 79 80

TRIM THIS EDGE

TABLE OF CONTENTS

OPERATING IN HOT WEATHER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

BOOSTER BATTERY CONNECTION . . . . . . . . . . . . . . . . . . . . . . . . . . .

MACHINE OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

JOB SITE OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

OPERATING THE LOADER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

MANUAL ATTACHMENT COUPLER . . . . . . . . . . . . . . . . . . . . . . . . . . .

HYDRAULIC ATTACHMENT COUPLER (IF EQUIPPED) . . . . . . . . . . . .

HIGH FLOW HYDRAULIC SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

TRANSPORTING THE MACHINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

PRIOR TO LOADING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Craning the Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

81 82 84 84 85 87 90 94 98 98 99

WHEEL AND TIRES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101

TRIM THIS EDGE

LUBRICATION / MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

465 LOADER LIFT ARM LOCK PIN . . . . . . . . . . . . . . . . . . . . . . . . . . .

450 - 450CT LOADER LIFT ARM SUPPORT STRUT . . . . . . . . . . . . . .

TILTING THE OPERATORS COMPARTMENT FORWARD . . . . . . . . .

LOWERING THE OPERATORS COMPARTMENT . . . . . . . . . . . . . . . .

ENGINE HOURMETER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

MAINTENANCE LUBRICATION SCHEDULE . . . . . . . . . . . . . . . . . . . . . .

SYSTEMGARD LUBRICATION ANALYSIS PROGRAM . . . . . . . . . . . .

ENVIRONMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

FLUIDS AND LUBRICANTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ACCESS DOORS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

LUBRICATION/MAINTENANCE CHART . . . . . . . . . . . . . . . . . . . . . . . . . .

EVERY 10 HOURS OR DAILY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

INITIAL 100 HOURS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

EVERY 250 HOURS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

EVERY 500 HOURS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

EVERY 1000 HOURS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

EVERY 2000 HOURS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

105 106 108 110 112 113 113 114 114 115 116 118 119 131 132 138 145 149

ADJUSTMENT/MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

STEEL TRACK ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ADJUSTING THE HAND THROTTLE . . . . . . . . . . . . . . . . . . . . . . . . . .

ADJUSTING THE DRIVE CHAIN TENSION . . . . . . . . . . . . . . . . . . . . .

MAINTENANCE OF THE SEAT BELT . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ROLL-OVER PROTECTION STRUCTURE . . . . . . . . . . . . . . . . . . . . . . . .

FIRE EXTINGUISHER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

PLASTIC AND RESIN PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

REMOVAL OF SLIDING SIDE WINDOWS (IF EQUIPPED) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

153 153 155 156 158 159 161 161

ELECTRICAL SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ALTERNATOR CHARGING SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . .

WORK LAMPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

TAIL LAMPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

163 163 164 165

II

TRIM THIS EDGE LEFT PAGE Bur 87364592na

162

SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

450 / 450CT / 465 ENGINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ELECTRICAL SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

COOLING SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

HYDRAULIC SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

POWER TRAIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

BRAKES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

OPERATING WEIGHTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SHIPING WEIGHTS (APPROXIMATE) . . . . . . . . . . . . . . . . . . . . . . . . .

ADDITIONAL WEIGHTS FOR OPTIONAL EQUIPMENT . . . . . . . . . . .

BUCKET CAPACITIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

MATERIAL WEIGHT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

GENERAL TORQUE SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . .

450 OPERATING DATA AND DIMENSIONS . . . . . . . . . . . . . . . . . . . .

450CT OPERATING DATA AND DIMENSIONS . . . . . . . . . . . . . . . . . .

465 OPERATING DATA AND DIMENSIONS . . . . . . . . . . . . . . . . . . . .

PALLET FORK WITH BRICK GUARD . . . . . . . . . . . . . . . . . . . . . . . . . .

171 171 172 173 173 173 173 174 174 174 175 176 177 180 184 188 192

AFTER DELIVERY CHECK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 197

III

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

TRIM THIS EDGE

MACHINE STORAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169 STORAGE PREPARATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169 STORAGE REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170

TRIM THIS EDGE IV

TRIM THIS EDGE LEFT PAGE Bur 87364592na

BD04M029

450 SKID STEER

This manual contains important information about the safe operation, adjustment and maintenance of your Skid Steer. Refer to the Detail Index at the end of this manual for locating specific items about your machine. This Skid Steer conforms to current safety regulations.

Use this manual as a guide. Your Skid Steer will remain a reliable working tool as long as it is kept in good working condition and serviced properly.

Do Not operate or permit anyone to operate or service this machine until you or the other persons have read and understand the safety, operation and maintenance instructions in this manual. Use only trained operators who have demonstrated the ability to operate and service this machine correctly and safely.

This Skid Steer, with standard equipment and authorized attachments, is intended to be used for general earth moving purposes, material handling, ditch digging, etc. Make sure that the machines are properly equipped and follow the instructions and safety precautions in this manual.

1

TRIM THIS EDGE RIGHT PAGE (Section First Page) Bur 87364592na

TRIM THIS EDGE

TO THE OWNER

TO THE OWNER Do Not use this machine for any application or purpose other than those described in this manual. Consult an authorized Dealer on changes, additions or modifications that can be required for this machine to comply with various country regulations and safety requirements. Unauthorized modifications will cause serious injury or death. Anyone making such unauthorized modifications is responsible for the consequences.

The Operators Manual is to be stored in the manual compartment equipped on this machine. Make sure this manual is complete and in good condition.

Contact your dealer to obtain additional manuals. Contact your Dealer for any further information or assistance about y o u r m a c h i n e . Yo u r D e a l e r h a s approved service parts. Your Dealer has technicians with special training that know the best methods of repair and maintenance for your Skid Steer.

TRIM THIS EDGE

Contact your Dealer for Operator Manuals translated into Spanish or French Canadian.

BD04D084

OPERATORS MANUAL STORAGE

2

TRIM THIS EDGE LEFT PAGE Bur 87364592na

TO THE OWNER

RIGHT, LEFT, FRONT AND REAR OF MACHINE Right-hand, left-hand, rear, and front, when used in this manual, indicate the right and left sides of the machine as seen from the operators seat.

MACHINE FRONT

MACHINE LEFT

TRIM THIS EDGE

MACHINE RIGHT

MACHINE REAR BS01F013

3

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

TO THE OWNER

PRODUCT IDENTIFICATION AND SERIAL NUMBERS Write your machine Model Number, Product Identification Number (P.I.N.) and Serial Numbers on the line provided below. If needed, give these numbers to your dealer when you need parts or information for your machine.

Make a record of the numbers. Keep the record and your Manufacturer’s Statement of Origin in a safe place. If the machine is stolen, report the number to your local law enforcement agency.

Model Number

Engine

Product Identification Number (P.I.N.)

TRIM THIS EDGE

BD04B077

Serial Number BD04C044

Model Number P.I.N.

4

TRIM THIS EDGE LEFT PAGE Bur 87364592na

TO THE OWNER

ROPS

Starter

BD04C055

BD04B086

Serial Number

Loader Bucket

Hydrostatic Pump TRIM THIS EDGE

Serial Number

BD04F031

BD04D085

Part Number

Serial Number

5

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

TO THE OWNER

MACHINE COMPONENTS

1 6

3 2 4

5

TRIM THIS EDGE

BD04M029

1. OPERATORS COMPARTMENT 2. LOADER LIFT ARMS 3. BUCKET

4. ENGINE COMPARTMENT 5. HYDRAULIC RESERVOIR 6. LOADER CONTROLS

6

TRIM THIS EDGE LEFT PAGE Bur 87364592na

TO THE OWNER

2

3 4

5

6

BD04M032

1. DRIVE CHAIN COMPARTMENT 2. HAND HOLD 3. UPPER ENGINE ACCESS DOOR

4. FUEL RESERVOIR 5. LOWER ENGINE ACCESS DOOR 6. COUNTERWEIGHT

7

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

TRIM THIS EDGE

1

TO THE OWNER

6

1

5

2 TRIM THIS EDGE

3

3

3

4

3

BD05C055

1. FINAL DRIVE SPROCKET 2. REAR IDLER WHEEL 3. ROLLER WHEELS

4. FRONT IDLER WHEEL 5. TRACK ADJUSTMENT ACCESS COVER 6. RUBBER TRACK

8

TRIM THIS EDGE LEFT PAGE Bur 87364592na

SAFETY RULES WARNING: This safety alert symbol indicates important safety messages in this manual. When you see this symbol, carefully read the message that follows and be alert to the possibility of death or serious injury.

M171C

Additional safety messages are used in the text of the manual to show specific safety hazards.

IMPORTANT: The safety messages in this chapter point out conditions which can happen during the normal operation and maintenance of your machine. These safety messages also give possible ways of dealing with these conditions.

BD04D084

OPERATOR’S MANUAL STORAGE BEHIND SEAT

READ THIS MANUAL COMPLETELY and make sure you understand the controls. All equipment has a limit.

Make sure you understand the speed, brakes, steering, stability and load characteristics of this machine before you start to operate.

DO NOT remove this manual or the safety manual from the machine. See your dealer for additional manuals. Also see the manual information on the Title pages (first and second pages in front o f t h e Ta bl e o f C o n t e n t s ) o f t h i s manual.

9

TRIM THIS EDGE RIGHT PAGE (Section First Page) Bur 87364592na

TRIM THIS EDGE

Most accidents involving machine operation and maintenance can be avoided by following basic safety rules and precautions. Read and understand all the safety messages in this manual, the safety manual, and the safety decals on the machine before you operate or service the machine. See your dealer if you have any questions.

The safety information given in this manual does not replace safety codes, insurance needs or, federal, state, and local laws. Make sure your machine has the correct equipment according to these rules or laws.

SAFETY

Safety Decals on this machine use the words, Danger, Warning or Caution, which are defined as follows: ●

DANGER: Indicates an immediate hazardous situation which, if not avoided, will result in death or serious injury. The color associated with Danger is RED.

●

WARNING: Indicates a potentially hazardous situation which, if not avoided will result in death or serious injury. The color associated with Warning is ORANGE.

●

CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices. The color associated with Caution is YELLOW.

ISO two panel pictorial symbol decals are defined as follows:

TRIM THIS EDGE

●

The first panel indicates the nature of the hazard.

●

The second panel indicates the appropriate avoidance of the hazard.

●

Background color is YELLOW.

●

Prohibition symbols such as

and

STOP

10

TRIM THIS EDGE LEFT PAGE Bur 87364592na

if used, are RED.

SAFETY

UTILITY SAFETY

●

Electrical Power Line

●

Gas Line

●

Water Line

●

Communication Line - Telephone or Cable Television

●

Sewer Line

IMPORTANT: Before beginning any machine operation, it is your responsibility to be aware of all such utility lines buried and overhead in the area of your project and to avoid them.

ALWAYS have all local utility companies mark the location of their lines.

In U.S.A. and Canada call one of many “One Call System Director” services. If you do not know the local number, call the national number (U.S.A. and Canada only): 1-888-258-0808.

IMPORTANT: Check with local authorities for laws, regulations and/or strict penalties requiring you to locate and avoid existing utilities.

Know the utility color code (U.S.A. and Canada): 1. Electric . . . . . . . . . . . . . . . . . . . Red 2. Gas, Oil, or Petroleum ........ Yellow 3. Communication, Telephone, Television ........................... Orange 4. Water ...................................... Blue 5. Sewer........................ Green/Brown 6. Proposed Excavation ............ White 7. Surveying ................................ Pink 8. Reclaimed Water and Slurry ..........

Purple After locating any buried utility lines, carefully dig a hole by hand and/or automatic vacuum equipment to the utility line to verify the location and depth of the line.

RH99G001

CALL ALL LOCAL UTILITY COMPANIES BEFORE YOU PERFORM ANY MACHINE OPERATION

11

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

TRIM THIS EDGE

Safety precaution MUST be followed when working near buried and overhead Utility Lines.

During operation it is likely that you will be working around or near buried or overhead utility lines which may include, but are not limited to:

SAFETY

PERSONNEL

GENERAL

●

Be prepared for emergencies.

Always have a first aid kit and a working fire extinguisher with you and know how to use each.

●

●

Avoid loose fitting clothing, loose or uncovered long hair, jewelry and loose personal articles.

It is the responsibility of the operator to read and understand the Operator’s Manual and other information provided and use the correct operating procedure.

Machines should be operated only by qualified operators.

●

Know and use the protective equipment that is to be worn when operating this machine. Hard hats, protective glasses, protective shoes, gloves, reflector type vests, respirators and ear protection are examples of typed of equipment that may be required.

●

Do not operate this machine or perform maintenance work if you have not had appropriate training and read and fully understand the instructions and warnings in this manual.

●

Wear the seat belt to maximize the protection capability of a ROPS (Roll Over Protective Structure).

●

Inspect the ROPS and seat belt mounting bolts on a daily basis to ensure their integrity.

●

Do not permit riders on the machine.

●

Make sure that all protective guards, canopies, doors, etc. are in place and secure.

●

Remove all loose object stored in the machine. Remove all objects which do not belong in or on the machine and its equipment.

●

Do not use the machine as a manlift.

●

TRIM THIS EDGE

Certain protective equipment should be replaced and renewed upon age and wear. Old hard hats may not afford the original users intention.

Faded and soiled vest are no longer as highly visible as original intent.

See the manufacture’s recommendation.

●

Do not rush. Walk, do not run.

●

Know and use the hand signals required for particular jobs and know who has the responsibility for signaling.

12

TRIM THIS EDGE LEFT PAGE Bur 87364592na

SAFETY

PROPER ENTRY AND EXIT Before exiting the skid steer: 1. Lower the boom and or attachments to the ground. If the operator must exit the skid steer with a raised boom always engage the boom lock pins, support strut and rest the boom arms on the lock pins or support strut.

2. Engage the parking brake.

3. Stop the engine.

Always face the front of the machine when you get on or off the machine.

DO NOT RUSH! Enter the skid steer from the front by using the bucket step and cab hand hold.

WARNING: Never exit the skid steer with the engine operating. Never exit the skid steer without first confirming the parking brake is set. Never exit the skid steer unless the boom and attachment are down resting on the ground or the boom is resting on the loader lift arm lock pin or support strut. ●

Use the recommended hand holds and steps with at least three points of support when getting on and off the machine. Keep steps and platform clean.

●

Do not jump off the machine.

●

Do not dismount while the machine is in motion.

●

Foreign material or grease on the steps and hand holds can cause an accident. Keep the steps and hand holds clean.

BD04D083

Step into the cab from the bucket and cab step area. Hand holds are provided on the front cab posts for entry and exit.

WARNING: Never enter or exit the skid steer unless the boom and attachment are resting on the ground or on the loader lift arm lock pin.

13

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

TRIM THIS EDGE

4. Remove the seat belt.

BD04D082

SAFETY

STARTING AND STOPPING PRECAUTIONS ●

●

●

TRIM THIS EDGE

●

Walk around the machine and warn all personnel who may be servicing the machine or are in the machine path prior to starting. Do not start until all personnel are clearly away from the machine. Sound the horn, if equipped, before starting.

Walk around the machine’s tool, attachment, or furthermost contact point to view operation danger area from the work site personnel view and angle.

Check that the parking device is applied, place the transmission in neutral or park as specified by the manufacturer, and disengage the PTO, if so equipped, before starting the machine.

Check that the parking brake is applied, place the ground drive controls in neutral and check that the auxiliary controls or switches are in neutral or off positions, before starting the machine.

●

Adjust, secure and latch the seat and fasten the seat belt before starting the machine.

●

Start and operate the machine only from the operator’s station.

●

Do not bypass the machine’s interlock system. The interlock system must be repaired if it malfunctions.

●

Use jumper cables only in the recommended manner. Improper use can result in battery explosion or unexpected machine motion.

Ventilate the battery area before using jumper cables. Make sure that using jumper cables will not interfere or harm electronic processing or computer devices.

●

Do not operate the engine in an enclosed area without adequate ventilation.

●

Park the machine on level ground whenever possible and apply the parking brake. On grades, park the machine with the wheels or track securely blocked.

●

Before leaving the operator’s station, lower the equipment to the ground, shut off the engine and place the function cancellation lever into the locked or up position.

●

Remove the starter key or disconnect switch when leaving the machine parked or unattended.

14

TRIM THIS EDGE LEFT PAGE Bur 87364592na

OPERATING PRECAUTIONS ●

●

Check brakes, steering and other machine control devices in accordance with the manufacturers instructions prior to starting operation. Observe all gauges or warning instruments for proper operation. Operate all controls to insure proper operation. If any malfunctions are found, remove the starter key or disconnect switch key.

Place a do not operate tag on the machine until the malfunction is corrected.

If a failure that causes loss of control such as steering, service brakes or engine occurs, stop the machine motion as quickly as possible, remove the starter key or disconnect switch key. Place a do not operate tag on the machine and keep it securely parked until the malfunction is corrected or the machine can be safely towed.

●

Know and understand the job site traffic flow patterns and obey signalmen, road signs and flagmen.

●

Know and understand that job site conditions may change on an hourly basis. Hills of dirt, debris or obstructions may grow and change from the time you began the day. It is your responsibility to monitor the changes and keep the machine, tools and attachments, etc. a safe distance.

●

Watch for bystanders and never allow anyone to be under or to reach through the machine and its equipment while operating.

●

Select a gear that will prevent excessive speed when going downhill. Do not coast downhill.

●

When roading a machine, know and use the signaling devices required on the machine. Provide an escort for roading where required.

●

On machines with independently operated wheel brakes, lock the brake pedals together when roading to provide equalized brake application.

●

Understand the machine limitations and keep the machine under control.

●

Operate and drive the machine with care and at speed compatible with conditions. Use extra caution when operating over rough ground, on slopes, and when turning.

●

Note and avoid all hazards and obstructions such as ditches, underground lines, trees, cliffs, overhead electrical wires or areas where there is danger of a slide.

Use the recommended transport devices when roading the machine.

Proper lights, flashers, signals and beacons may be required. Follow local, state and federal regulations.

●

Use the approved drawbar and / or attachment point when using the machine for towing. If a cable or chain is used, keep people away from the tow line.

●

Before you operate at night, check that all lamps illuminate.

●

If your machine has a cab make sure that all windows are clean and that the windshield wipers work correctly.

●

●

Carry loads in recommended positions for maximum stability.

●

Never lift loads in excess of capacity.

●

Use the recommended machine ballast and counterweighting.

15

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

TRIM THIS EDGE

SAFETY

SAFETY ●

Engine exhaust fumes can cause death. If you operate this machine in an enclosed area, make sure there is ventilation to replace the exhaust fumes with fresh air.

●

●

●

●

TRIM THIS EDGE

●

Check all controls in a clear area and make sure the machine is operating correctly.

If you have extreme conditions, such as a fire, etc., and you are forced to leave the machine, do not step off the machine. Jump as far from the machine as possible with your feet together and do not touch the ground with your hands.

●

Dust, fog, smoke, etc., can decrease your vision and cause an accident.

Stop the machine or decrease the speed until you can see.

Do not operate the machine if you do not feel well. This can be dangerous for you and for the people around you.

●

Contact with high voltage power lines, underground cables, etc., can cause serious injury or death from electrocution.

You must make a judgment if weather, road, or earth conditions will permit safe operation on a hill, ramp, or rough ground.

●

Stay away from hazardous areas such as ditches, overhangs, etc.

Walk around the work area before you start and look for hazards.

●

Be alert and always know the location of all workers in your area.

Keep all other persons completely away from your machine. Injury or death can result if you do not follow these instructions.

●

Develop fluid and smooth operating techniques and maintain the surface condition where the machine travels in order to control vibration transfer to the operator.

Before you drive or operate in an area with high voltage lines, cables, or a power station, tell the power or utility company what you are going to do. You MUST HAVE THE POWER DISCONNECTED OR KEEP A SAFE WORKING DISTANCE from the lines, cables, or power station. Keep all parts of the machine a safe distance away from the power source. You must also know any federal, state/ provincial, or local safety codes or regulations that apply to the job site.

If a part of the machine touches high voltage power: 1. Warn other workers NOT TO TOUCH THE MACHINE and to stay away from the machine.

2. If you can break contact, reverse the operation that caused contact with the high voltage power, and move the machine away from the danger area. If you cannot break contact stay in the machine until the utility company de-energizes the line and tells you that the power is off.

16

TRIM THIS EDGE LEFT PAGE Bur 87364592na

MAINTENANCE PRECAUTIONS ●

●

Avoid lubrication or mechanical adjustments with the machine in motion or the engine operating. If the engine must be in operation to make certain adjustments, place the transmission in neutral, apply the parking device, place the equipment in a safe position, securely block the wheels and use extreme caution.

●

Securely block the machine or any component that may fall before working on the machine or component. If possible, use a back up or secondary blocking device, also.

●

To prevent unexpected movement, securely block working elements when repairing or changing working tool parts such as cutting edges.

●

Never make repairs on pressurized components, fluid, gas or mechanical until the pressure has been relieved according to the manufacturer’s instructions.

●

Use extreme caution when removing radiator caps, drain plugs, grease fittings or pressure taps. Park the machine and let it cool down before opening a pressurized tank.

●

Release all pressure before working on systems which have an accumulator.

●

Use a piece of cardboard, newspaper, or wood to check for pressurized leaks to prevent fluid penetrating the skin. Pressurize accumulators with the proper gas according to manufacturers. recommendations.

●

When inflating tires, use a selfattaching inflation chuck with remote shutoff and stand clear of the tire.

Position yourself beside the tire and not beside the rim.

Do not attempt repairs unless trained. Refer to manuals and experienced repair personnel for help.

321-4614

●

●

Before you service the machine, put a Do Not Operate tag on the key switch. Make sure that the machine is clearly “tagged out”. A DNO tag is included in this machine’s Operator Manual packet.

Wear protective glasses and other required safety equipment when servicing or repairing the machine.

●

Wear gloves to protect hands when handling cable.

●

Disconnect the battery before working on the electrical system.

Know the consequences of disconnecting any electronic or computer devices.

17

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

TRIM THIS EDGE

SAFETY

SAFETY ●

It is not recommended to tow this machine.

FUEL HANDLING PRECAUTIONS

●

Observe proper procedures.

●

●

Whenever servicing or replacing hardened pins, etc., use a brass drift or other suitable material between the hammer and pin. Alternative: Use a brass hammer, drift or suitable material on the pin, etc.

Do not smoke or permit open flames while fueling or near fueling operations.

●

Keep the brakes and steering systems in good operating condition.

Never remove the fuel cap or refuel gasoline engine powered machines with the engine running or hot. Never allow fuel to spill on hot machine components. Never allow fuel to spill on the environment.

●

Replace all missing, illegible or damaged safety signs. Keep all safety signs clean.

To avoid spilling fuel maintain control of the fuel filler nozzle when filling the tank.

●

Do not fill the fuel tank completely to the top. Allow room for expansion.

●

Clean up spilled fuel immediately and dispose of contaminated material in an environmentally correct manner.

●

Tighten the fuel tank cap securely.

Should the fuel cap be lost, replace it only with the original manufacturers approved cap. Use of a nonapproved cap without proper venting may result in pressurization of the tank.

●

Never use fuel for cleaning purposes.

●

Use the correct fuel grade for the operating season.

● ●

maintenance

TRIM THIS EDGE 18

TRIM THIS EDGE LEFT PAGE Bur 87364592na

SAFETY

BURN PREVENTION WARNING: BATTERY ACID CAUSES SEVERE BURNS. Batteries contain sulfuric acid. Avoid contact with skin, eyes or clothing.

Antidote: EXTERNAL - Flush with water.

Antidote: INTERNAL - Drink large quantities of water or milk.

DO NOT induce vomiting. Seek medical attention immediately.

EYES - Flush with water for 15 minutes and seek medical attention immediately.

WARNING: BATTERIES PRODUCE EXPLOSIVE GASES. Keep sparks, flame, cigars and cigarettes away. Ventilate when charging or using in enclosed area. Always wear eye protection when working near batteries. Wash hands after handling. KEEP OUT OF REACH OF CHILDREN. M144B

●

HAZARDOUS CHEMICAL PRECAUTIONS

When the battery electrolyte is frozen, the battery can explode if, you try to charge the battery, or you try to jump start and run the engine.

To prevent the battery electrolyte from freezing, try to keep the battery at full charge. If you do not follow these instructions, you or others in the area can be injured Hot coolant can spray out if the radiator cap is removed. To remove the radiator cap, let the cooling system cool, turn to the first notch, wait until the pressure is released, then remove the radiator cap.

●

If you are exposed to or come in contact with hazardous chemicals you can be seriously injured. The fluids, lubricants, paints, adhesives, coolants, etc., used with your machine can be hazardous.

●

Before you service this machine and before you dispose of the old fluids and lubricants, always remember the environment. DO NOT put oil or fluids into the ground or into containers that can leak.

●

Check with your local environmental or recycling center or your dealer for correct disposal information.

TRANSPORTING PRECAUTIONS ●

Know the rules, laws, and safety equipment necessary for transporting this machine on a road or highway.

19

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

TRIM THIS EDGE

●

SAFETY

ROLL-OVER PROTECTIVE STRUCTURE ●

Do NOT modify the ROPS in any manner. Unauthorized modifications such as welding, drilling, cutting, or adding attachments can weaken the structure and reduce your protection.

Replace ROPS if it is subjected to roll-over or damage. Do not attempt to repair.

FIRE EXTINGUISHER ●

It is recommended that you have a fire extinguisher on your machine.

Contact your dealer for the type and location of a fire extinguisher on this machine

TRIM THIS EDGE 20

TRIM THIS EDGE LEFT PAGE Bur 87364592na

SAFETY

SEAT BELT PRECAUTIONS 3

2

To unlatch the seat belt, press the red button (4) on the r ight latch mechanism.

1

The seat belt will automatically retract.

4

BP96N110

To latch the seat belt, pull the left belt strap (1) from the retractor.

Insert the metal end (2) into the right latch mechanism (3) on the right side of the seat.

WARNING: Before starting the engine ensure seat belts are securely fastened. The seat belt can help insure your safety if it is used and properly maintained. Never wear a seat belt loosely or with slack in the belt system. Never wear the belt in a twisted condition or pinched between the seat structural members.

M422B

WARNING: Securely fasten your seat belt. Your machine is equipped with a ROPS cab, ROPS canopy or ROPS frame for your protection. The seat belt can help insure your safety if it is used and maintained. Do not rewire to bypass the seat switch or seat belt switch.

M1116

21

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

TRIM THIS EDGE

BP96N109

SAFETY

SPECIFIC PRECAUTIONS TO THIS MACHINE ●

Keep the load or tool as low as possible while moving the machine around the jobsite.

●

If this machine is equipped with an engine pre-heat cold start system you must not use ether.

●

ALWAYS activate the mechanical loader arm lock pin or support strut before exiting a machine with the loader arms up and/or when servicing or repairing the unit with the loader arms up. Failure to do so could result in death or serious injury.

3. Engage the loader lift arm lock pin, using the lock pin control lever located in the right rear corner of the operator’s compar tment, by moving the lever toward the center of the machine.

TRIM THIS EDGE

Before exiting a machine with the boom up engage the lock pin:

BD04E072

LOCK PIN (SHOWN ENGAGED)

IMPORTANT: Remove the attachment before raising the loader lift arms and locking the arms in the UP position.

This will place the lock pin in the position shown.

1. While sitting in the operator’s seat, with the seat bar down, and the engine running, roll the coupler attachment all the way back.

2. Raise the loader lift arms to the maximum height.

A_PIN

4. Lower the loader lift arms until the loader lift arm link rests against the lock pin.

BD04D087

LOCK PIN CONTROL LEVER (SHOWN ENGAGED) 256365A2

LOADER LIFT ARM LEVER DECAL

22

TRIM THIS EDGE LEFT PAGE Bur 87364592na

SAFETY Disengaging the Loader Lift Arm Lock Pin:

TRIM THIS EDGE

1. While sitting in the operator’s seat, with the seat bar down, start the engine and raise the loader lift arms until the loader lift arm link is no longer contacting the lock pin.

BD04D086

2. To disengage the lock pin, move the lock pin control lever toward the r i g h t s i d e o f t h e m a c h i n e, a s shown.

BD04E073

3. Slowly lower the loader lift arms to the ground.

23

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

SAFETY

450 LOADER LIFT ARM SUPPORT STRUT WARNING: If you service the machine with the loader lift arms raised, always use the cylinder lock support strut to block up the loader lift arms.

Failure to follow this procedure can cause serious injury or death if the loader lift arms are lowered by accident.

M736

IMPORTANT: Installing the Support Strut can be performed as a one or two person procedure so that the operator is not entering or exiting the operators compartment under unsupported loader lift arms.

Before exiting a machine with the boom up engage the support strut: 1. While sitting in the operator’s seat with the seat bar down lower the loader lift arms to the ground and stop the engine.

TRIM THIS EDGE

BD04M021

4. Start the engine and slowly raise the loader lift arms until the support strut is on the lift cylinder rod.

Lower the loader lift arms until the support strut makes contact with the lift cylinder tube. Stop the engine.

BD04M022

2. Remove the pin from the support strut.

3. After the pin is removed, lower the support strut onto the lift cylinder.

BD04M023

5. Install the pin in the support strut.

24

TRIM THIS EDGE LEFT PAGE Bur 87364592na

SAFETY Storing the Support Strut: IMPORTANT: Storing the Support Strut should be performed as a two person procedure so that the operator is not entering the operators compartment under unsupported loader lift arms.

1. Have the operator enter the operators compartment and start the engine. Raise the loader lift arms approximately 1 to 2 inches (25 to 55 mm).

BD04M023

2. Stop the engine. Make sure the loader controls are locked. Do not exit the operators compartment.

Have a second person remove the support strut pin.

4. Have the operator start the engine and lower the loader lift arms to the ground. Stop the engine.

25

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

TRIM THIS EDGE

BD04M024

3. Have a second person raise the support strut to the storage position and install the pin. After installing the pin the second person should move away from the machine.

SAFETY

EMERGENCY EXIT The rear window can be removed to provide an exit for the operator in the event the front exit is blocked.

2

1 BD01C270

2. TOP OF REAR WINDOW PUSHED OUT

Loosen the knobs.

BD04D084

Remove the rear window by pushing outward.

1. WINDOW RETAINING KNOBS

TRIM THIS EDGE

Turn the key switch OFF.

Exit the machine through the rear opening.

Raise the seat restraint bar.

Release the seat belt.

WARNING: Know and understand the emergency exit. Practice this procedure as you would a fire drill. Confirm that all operator’s know this emergency exit procedure.

Locate the two window retaining knobs attached to the rear window. One each side.

26

TRIM THIS EDGE LEFT PAGE Bur 87364592na

SAFETY

OPERATOR PRESENCE AND ROPS POSITION SWITCHES The operator presence switch requires the operator to be seated in the operators seat when operating this skid steer.

1

1 BD04M057

The ROPS position switch requires that t h e RO P S b e i n t h e l o cke d d ow n position for the ground drive system or the hydraulic system to be operable.

BD04E078X

1. LOCATION OF OPERATOR PRESENCE SWITCH

This switch is located on the left rear of the ROPS, when tilted.

T h e o p e ra t o r p r e s e n c e sw i t c h i s located in the seat cushion.

If the operator leaves the seat (even with the seat bar down) the loader controls and the ground drive system become disabled after 3 seconds.

Refer to the right hand instrument panel warning light.

Make sure the operator presence (seat interlock system) is working properly at all times. See page 77 for testing procedures.

27

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

TRIM THIS EDGE

1. ROPS POSITION SWITCH

SAFETY

SEAT BAR Before this skid steer can be operated the restraint bar must be in the down position.

3 1

BD04M056

3. FASTEN SEAT BELT REMINDER (LOCATED ON TOP FACING PORTION OF THE RESTRAINT BAR) BK98E018

The seat bar provides the following features:

1. RESTRAINT BAR IN LOCKOUT POSITION

TRIM THIS EDGE

2

●

In combination with the seat belt, keeps the operator in the seat during operation.

●

Provides an arm rest while the operator is using the travel / loader control levers.

●

Locks the loader controls and the ground drive functions when in UP position.

BK98E019

2. RESTRAINT BAR IN OPERATING POSITION

28

TRIM THIS EDGE LEFT PAGE Bur 87364592na

SAFETY

SAFETY DECALS The following safety decals have been placed on your machine in the areas indicated. The following graphics are for replacement location. Safety decals are intended for the personal safety of you and those working with you. Please take this manual, walk around your machine and note the content and location of these warning decals. Review these decals with all machine operators. It is the Owner’s responsibility to keep the decals legible. If they are not, obtain replacements from your dealer. Part numbers are on the decal.

WARNING: Make sure that the decals are perfectly legible, clean them regularly and replace decals that are destroyed, lost painted over or no longer legible, with new ones. When parts bearing decals are replaced, be sure to put new decals on each new part.

WARNING: Injury or death can result if you cannot read a safety decal or if a safety decal is missing. Replace any missing or damaged safety decal and keep all safety decals clean. See your dealer for new safety decals.

SC002

NOTE: When you clean the decals, use only a cloth, water, and soap. Do not use solvent, gasoline, etc.

NORTH AMERICAN TEXT

ISO 382622A1 / 256147A1

READ THE OPERATOR’S MANUAL DECAL

29

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

TRIM THIS EDGE

M1160

SAFETY

1

TRIM THIS EDGE

BD04B086 / 321-7040

1. DANGER: ENGINE START WARNING

30

TRIM THIS EDGE LEFT PAGE Bur 87364592na

SAFETY

2

BD04D088 / 251744A1

2. DANGER: CRUSH HAZARD

3 3

BD04M037 /

3. DANGER: DO NOT USE ETHER

31

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

TRIM THIS EDGE

2

SAFETY

4 4

BD04B097 / 384267A1

4. WARNING: ENTANGLEMENT HAZARD

TRIM THIS EDGE

5 5

BD04G013

5. WARNING: PINCH POINT

32

TRIM THIS EDGE LEFT PAGE Bur 87364592na

SAFETY

6 6

BD04C046 / 382622A1

TRIM THIS EDGE

6. WARNING: READ OPERATORS MANUAL

33

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

SAFETY

7 7

7. INFORMATION DECAL: LIFT CAPACITY - 465 SHOWN

BD04H057 / 87440296

TRIM THIS EDGE

450 capacity ............1111 kg (2450 lbs) 450CT capacity .......1111 kg (2450 lbs) 465 capacity .............1360kg (3000 lbs)

8

8

BK97E009

8. WARNING: USE THE SUPPORT STRUT

34

TRIM THIS EDGE LEFT PAGE Bur 87364592na

SAFETY

9

BD01C073

9. DANGER: CRUSH HAZARD

10

10

BD04F032 / 251748A1

10. WARNING: TIP HAZARD

35

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

TRIM THIS EDGE

9

SAFETY

11

11

TRIM THIS EDGE

11. CAUTION: INSPECT COUPLER-LATCH BEFORE OPERATING

BD04H058

12

12

BD04M037 / 629086

12. DANGER: DO NOT USE ETHER ON MACHINES EQUIPPED WITH AN ENGINE PRE-HEAT COLD START SYSTEM

36

TRIM THIS EDGE LEFT PAGE Bur 87364592na

SAFETY

13 13

TRIM THIS EDGE

13

13

BD04D089 / BD04D091 / 139729A1

13. LIFT HOOK LOCATIONS

37

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

SAFETY

14 14

14 TRIM THIS EDGE

BD04D092 / BD04D093 / 139728A1

14. TIE DOWN LOCATIONS (EACH SIDE)

15 15

BD04C039 / 384260A1

15. PRESSURIZED SYSTEM HAZARD

38

TRIM THIS EDGE LEFT PAGE Bur 87364592na

SAFETY

16

TRIM THIS EDGE

16

16. LOCATED TO THE RIGHT OF THE OPERATOR

39

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

BD01C076 / 255927A1

SAFETY

17

17 TRIM THIS EDGE 17. 369848, WARNING: IMPACT AREA, GREASE UNDER PRESSURE

40

TRIM THIS EDGE LEFT PAGE Bur 87364592na

BD05B032 / 369848

INSTRUMENTS AND CONTROLS INSTRUMENT PANEL The instrument panel is located on the upper right-hand side of the cab. The operator may easily view the instrument lamps and indicators yet still have a clear and safe view of the worksite.

Once in the seat the alarm sounds and all lamps light briefly.

The fuel gauge and hourmeter will remain illuminated, for approximately 20 seconds, for operator monitoring.

The machine will be in Park when started. With the operator in the seat a nd the Seat Ba r down , t he p a r k indicator lamp will be illuminated and the Park switch blinking. The operator restraint bar must be down and the operator in the seat. The operator must Push the Park Brake Switch to release the brakes and activate the loader controls.

TRIM THIS EDGE

1

3

The Parking Brakes will be set when: ●

The park brake switch is activated and the park brake light is illuminated.

●

The engine is shut off.

●

The engine is running and the restraint bar is up.

●

The operator leaves the seat.

BS96H055

2

BD04C083

1. SEAT BELT REMINDER LAMP 2. PARK BRAKE SWITCH 3. PARK BRAKE LIGHT

1. Seat Belt Reminder: This lamp flashes when the machine is first started to remind the operator to place the lap bar down and fasten the seat belt.

41

TRIM THIS EDGE RIGHT PAGE (Section First Page) Bur 87364592na

INSTRUMENTS/CONTROLS

Key Switch 2. Key Switch: Located at the top of the Instrument Panel. This is a 4 position switch.

2

TRIM THIS EDGE

BD04E075

System Power (Accessory): This position energizes the instrument panel lamps and the accessory switches.

BS96H041

IMPORTANT: Battery will discharge if left in this position.

Stop: Turn the key to this position to stop the engine and deenergize the electrical system.

BS96H076

Run: This position energizes the electrical system and is the normal key position when the engine is running.

This is the position to be used if the machine is equipped with the BS96H078 Engine Pre-Heat Cold Start System. In cold temperatures the switch should remain in this position until the Engine Pre-Heat Indicator Lamp goes out.

Start: Turn the key to this position to actuate the starter motor and start the engine.

BS96H077

42

TRIM THIS EDGE LEFT PAGE Bur 87364592na

INSTRUMENTS/CONTROLS

3

TRIM THIS EDGE

4

A_TEST

3. Fuel Gauge:

BS96H048

This symbol indicates the fuel level gauge, which is located to the right of the symbol. The gauge consists of a series of bars that indicate the level of fuel in the fuel tank. When all of the bars are visible the fuel tank is full. The first bar indicates the following amount

of fuel: Solid Bar ....................................................................... 4.0 U.S. gals (15.1 litres) Flashing Bar .................................................................. 3.0 U.S. gals (11.4 litres) 4. Hourmeter:

BS96H096

The hourmeter shows the total hours of engine operation. Both hours and tenths of an hour will display. The hourmeter should be used to measure the time between scheduled maintenance intervals.

43

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

INSTRUMENTS/CONTROLS

5

7

6 8

5. Work Lamps: Depress the work light symbol on this switch to turn the front and rear work lamps on. Depress the switch again to turn them off.

TRIM THIS EDGE

6. Auxiliary Hydraulic Interlock Override: When an operator leaves the seat, flow to an attachment will normally be halted via engine shutoff or direct hydraulic flow shutoff. Push this button and leave the seat within thirty seconds to defeat this interlock BS04F101

7. Road Lamps: Depress the light symbol on this switch to turn the front lamps and red tail lamps on. Depress the switch again to turn them off.

8. Parking Brake Switch: This lamp blinks when the Parking Brake is set. The Operator must have the restraint bar down, in the working position, and press the switch to release the brakes. Push the switch again to set the brakes.

BS96H049

44

TRIM THIS EDGE LEFT PAGE Bur 87364592na

INSTRUMENTS/CONTROLS

9 10 11

BD04E075

9. Engine Oil Pressure Lamp and Alarm: This warning lamp flashes and the alarm sounds if, with the engine running there is no or low oil pressure in the engine. DO NOT RUN the engine if this warning lamp illuminates.

BS96H052

10. Coolant Temperature Warning Lamp and Alarm: This lamp flashes and the alarm sounds when the engine is running and the engine temperature is too high. Stop the engine and service the problem.

BS96H050

11. Engine Air Filter Warning Lamp: This lamp will flash when the engine air filter becomes restricted and requires servicing. Service immediately.

BS96H056

BC02N191

12. Engine Pre-Heating System: In cold climate starting conditions, after turning the key switch to RUN, the Engine Pre-Heating Lamp will illuminate, instructing the Operator that incoming air is being pre-conditioned for smoother starting. The Operator must wait until the lamp goes out before starting the engine.

45

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

TRIM THIS EDGE

12

INSTRUMENTS/CONTROLS

13

14

15 16

TRIM THIS EDGE

BD04E075

13. Transmission Charge Pressure Warning Lamp: This warning lamp flashes and the alarm sounds if there is no, or low oil pressure in the transmission. Do not run the machine if the warning lamp illuminates.

BS99J181

14. Hydraulic Fluid Temperature Warning Lamp: This warning lamp will flashes and the alarm will sound if the temperature of the hydraulic fluid becomes extreme. Do not work the machine if the condition exists.

BC0B123

BC00B113

15. Hydraulic Oil Filter Warning Lamp: This warning lamp will flash if the engine is running and the hydraulic filter is restricted. Lower the engine speed until the light goes out. If the oil is to operating temperature and the light is on continuously, change the filter.

16. Brake Indicator Lamp: This warning lamp will illuminate when the brakes are engaged.

BS96H049

46

TRIM THIS EDGE LEFT PAGE Bur 87364592na

INSTRUMENTS/CONTROLS

Right Hand Console This console, to the right of the operator, controls the cab environment and holds four switch panels.

4 1

1. Hazard Switch: Push this switch to activate the Hazard flasher lamp.

BC04K301

2. Blank Plug:

2

3. High / Low Hydraulic Control Switch:

3

Use this two position switch to regulate Auxiliary hydraulic flow. The switch is illuminated when in the High Flow H position.

5 7

Flow Rates Aux hyd ................................. 21.9 gpm High Flow Aux hyd................. 41.8 gpm

5. Blower Fan Switch:

NOTE: Refer to the attachment manufacturers specifications prior to selecting low or high flow.

There are three blower switch speeds. By turning the switch clockwise from BS99N111 off, the blower speed will increase from low to medium to high. The switch will remain where set by the operator.

4. Rotating Beacon: If the machine is equipped with a beacon, use this switch for activation.

6. Air Conditioning Switch: This two position switch turns the air conditioning BC00B112 system on or off. This switch is illuminated when in the ON position.

BC00B082

7. Temperature Control Switch: Adjust the switch for the required comfort level. Red area for warm and blue area for cold.

47

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

TRIM THIS EDGE

6

INSTRUMENTS/CONTROLS

Left Hand Console

2 1

TRIM THIS EDGE

012

009

FUSE AND RELAY COVER REMOVED

This console, to the left of the operator, holds two switches and a covered fuse and relay compartment. Remove the thumbscrew, at the back of the cover, above, to remove the fuse and relay cover. The fuse decal is under the cover.

1. Hydraulic Coupler Switch: Push the lock side or the unlock side of this switch to lock or unlock the hydraulic BC04F113 c o upl e r. Th is sw it c h i s used in conjunction with lift, tilt or auxilliary hydraulic controls for activation.

2. Blank Plug:

48

TRIM THIS EDGE LEFT PAGE Bur 87364592na

INSTRUMENTS/CONTROLS

BATTERY MASTER DISCONNECT SWITCH

1

1

BD04B094 / BD04M025

1. BATTERY MASTER DISCONNECT SWITCH 465 AND 450 RESPECTIVELY

TRIM THIS EDGE

1. Battery Master Disconnect Switch The Battery Master Disconnect Switch has two positions: ON and OFF ON

BS98M034

This position supplies power from the battery to the electrical system.

OFF

BS98M034

This position disconnects all electrical power from the battery to the machine.

IMPORTANT: DO NOT attempt to use the Battery Master Disconnect Switch to stop the engine. The Master Disconnect Switch will not stop the running engine and may cause damage to the electrical system or components if switched off with a running engine.

49

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

INSTRUMENTS/CONTROLS

STEERING AND TRAVEL WITH H PATTERN CONTROLS 1

F

F

N

N

R

R

2

TRIM THIS EDGE

BD05A015

1. LEFT HAND CONTROL LEVER 2. RIGHT HAND CONTROL LEVER

The H steering and travel controls are directed by the left-hand and right-hand control levers. The machines left and right drive motors will move in the direction the control lever is pushed or pulled from neutral, or center. The control on either side, completely and independently controls the drive motor on that side.

The travel speed is determined by the distance from neutral each lever is moved.

The farther the levers are pushed or pulled the faster that motor will move. To stop the machine move the control levers to neutral position.

Although the machine will turn and counter-turn sharply it is most efficient to travel through forward or reverse gradually. Track machines steer and travel with the same commands.

STRAIGHT AHEAD DRIVE:

STRAIGHT REARWARD DRIVE:

Push both of the controls forward, from neutral, to move the machine forward.

Pull both of the controls rearward, from n e u t r a l , t o m o ve t h e m a c h i n e i n reverse.

WARNING: Before moving the machine in any REVERSE direction, you must confirm that the area is clear of personnel and objects. Sound the horn, if equipped.

50

TRIM THIS EDGE LEFT PAGE Bur 87364592na

INSTRUMENTS/CONTROLS

STEERING AND TRAVEL WITH H PATTERN CONTROLS F

F

N

N

R

R

2

BD05A015

LEFT TURN STEERING:

RIGHT TURN STEERING:

Push both levers slightly forward and once the machine begins moving, push the right-hand control lever slightly further than the left. Push the righthand control lever in a more forward direction and the machine will turn more sharply.

Push both levers slightly forward and once the machine begins moving push the left-hand control lever further than the right. Push the left-hand control lever in a more forward direction and the machine will turn more sharply.

For reverse right turning, slowly, pull both levers slightly rearward and once the machine begins moving, pull the left-hand control lever slightly further than the right. Pull the right-hand c o n t r o l l eve r i n a m o r e r e a r wa r d direction and the machine will turn more sharply.

For reverse left turning, slowly, pull both levers slightly rearward and once the machine begins moving, pull the righthand control lever slightly further than the left. Pull the right-hand control lever in a more rearward direction and the machine will turn more sharply.

51

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

TRIM THIS EDGE

1

INSTRUMENTS/CONTROLS

Turning A Machine With H Pattern Controls

BS06G022

BS06G023

TRIM THIS EDGE

PIVOT TURN - (POWER TO ONLY ONE SIDE)

Counter-Rotation Turn - (Power to both sides - opposing directions)

To make a pivot turn left: Hold the left steering control lever in neutral and push the right steering control lever forward.

To counter rotate left: Pull the left steering control lever rearward and push the right steering control lever forward.

To make a pivot turn right: Hold the right steering control lever in neutral and push the left steering control lever forward.

To counter rotate right: Pull the right steering control lever rearward and push the left steering control lever forward.

To make a pivot turn in reverse left: After confirming that all personnel and objects are clear, Hold the left steering control lever in neutral and push the right steering control lever rearward.

To make a pivot turn in reverse right: After confirming that all personnel and objects are clear, hold the right steering control lever in neutral and pull the left steering control lever rearward.

BS06G024

Gradual Turn - (Power to both sides To make a gradual turn left: Push the right steering control lever fur ther forward while pushing the left steering control lever partially forward.

To make a gradual turn right: Push the left s teer ing control leve r fur ther forward while pushing the right steering control lever partially forward.

52

TRIM THIS EDGE LEFT PAGE Bur 87364592na

INSTRUMENTS/CONTROLS

LIFT ARM AND BUCKET CONTROLS - H PATTERN

1

5 2

BD05A015

1. Lift Arm Raise:

4. Bucket Rollback: (Curl)

The left-hand control lever controls the lift ar m. The lift ar m will raise by pivoting the handle UP toward the outside Left of the cab.

Pivot the control lever toward the inside of the machine to ROLLBACK or CURL the bucket.

2. Lift Arm Lower:

Pivot the control lever toward the outside right position to DUMP the bucket.

5. Bucket Dump:

Pivoting the handle DOWN to the inside of the cab will lower the lift arm.

3. Lift Arm FLOAT: Pivoting the handle DOWN until a slight jump is felt will place the control lever in the FLOAT position. This is a detented position and the lever will remain in this position until the operator pulls it back out and toward neutral.

In this detented, FLOAT position, the lift arm will float over changing ground contour.

53

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

TRIM THIS EDGE

4

3

INSTRUMENTS/CONTROLS

Instructional Decals For H Pattern Steering And Controls A

C

B TRIM THIS EDGE

87438592 /

See the control lever application decals on the machine and understand the functions before starting the machine or beginning any operation. Decal (A) shown above, is located on the left inside of the cab. Decal (B) is located on the inside left cab upright. Decal (C) is located on the inside right cab upright. If you have any questions about the operation or function of the control levers contact your Dealer.

54

TRIM THIS EDGE LEFT PAGE Bur 87364592na

INSTRUMENTS/CONTROLS

STEERING AND TRAVEL WITH ISO PATTERN PILOT CONTROLS F 1 N

BS06N853

1. ISO PILOT CONTROL DRIVE LEVER

The ISO Pattern steering and travel controls are directed with this lever only. Use the face of a clock for orientation. The machine will move in the direction the lever is moved from neutral, center. To stop the machine release the lever and it will return to neutral. Although the machine will turn and counter-turn sharply it is best to travel through forward or reverse gradually when turning. Track type machines steer and travel with the same commands.

STRAIGHT AHEAD DRIVE:

LEFT TURN STEERING:

Push the control lever straight ahead, 12:00 position, and the machine will move forward.

From forward travel push the control lever to the 11:00 position and the machine will begin to travel left. Move the control lever, fur ther left, down toward 9:00 and the machine will move sharper left.

STRAIGHT REARWARD DRIVE: Pull the control lever straight rearward, 6:00 position and the machine will move rearward.

RIGHT TURN STEERING: From forward travel push the control lever to the 1:00 position and the machine will begin to travel right. Move the control lever, further right, down toward 3:00 and the machine will move sharper right.

WARNING: Before moving the machine in any REVERSE direction, you must confirm that the area is clear of personnel and objects. Sound the horn, if equipped.

55

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

TRIM THIS EDGE

R

INSTRUMENTS/CONTROLS

TURNING A MACHINE WITH ISO PATTERN PILOT CONTROLS

BS06G035

BS06G036

PIVOT TURN - (POWER TO ONLY ONE SIDE)

COUNTER-ROTATION TURN - (POWER TO BOTH SIDES - OPPOSING DIRECTIONS)

TRIM THIS EDGE

To make a pivot turn left: From neutral, push the pilot control dr ive leve r forward, slightly and then left toward 10:00.

To counter- rotate left: Push the pilot control drive lever straight left toward the 9:00 position. The left drive will engage reverse as the right drive will engage forward.

To m a ke a p i vo t t u r n r i g h t : Fr o m neutral, push the pilot control lever forward, slightly and then right toward 2:00.

To counter-rotate right: Push the pilot control drive lever straight right (inward) toward the 3:00 position. The right drive will engage reverse as the left drive will engage forward.

To make a pivot turn reverse left: From neutral, pull the pilot control drive lever rearward, slightly and then right toward 4:00.

To make a pivot turn reverse right: From neutral, pull the pilot control drive lever rearward, slightly and then left toward 8:00.

WARNING: Keep hands and feet on the appropriate controls at all times so control of the skid steer is maintained.

IMPORTANT: Although the machine will make sharp pivot and counterrotation turns it is more efficient to turn through forward or reverse, gradually when operating.

56

TRIM THIS EDGE LEFT PAGE Bur 87364592na

INSTRUMENTS/CONTROLS

TURNING A MACHINE WITH ISO PATTERN PILOT CONTROLS

BS06G037

GRADUAL TURN - (POWER TO BOTH SIDES SAME DIRECTION)

TRIM THIS EDGE

To make a gradual tur n left: From neutral, push the pilot control drive lever forward and then slightly toward the 11:00 position.

To make a gradual turn right: From neutral, push the pilot control drive lever forward and then slightly toward the 1:00 position.

57

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

INSTRUMENTS/CONTROLS

LIFT ARM AND BUCKET CONTROL WITH ISO PATTERN PILOT CONTROLS 3

A

2

4

N

5

1

TRIM THIS EDGE

BS06N853

A. PILOT CONTROL PATTERN LIFT ARM AND BUCKET CONTROL LEVER

Lift Arm Raise And Lower Control:

Bucket Dump And Curl Control:

The lift arm is controlled by pushing or pulling the right pilot control lever on this configuration.

The bucket is also controlled by the Right Pilot Control Lever.

4. Rollback: (Curl)

1. Lift Arm Up:

The bucket will rollback (curl) when the Right Pilot Control Lever is pivoted inward.

The lift arm will raise UP by pulling back on the Right Pilot Control Lever.

5. Dump:

2. Lift Arm Down:

Pivoting the lever up toward the outside of the cab will dump the bucket.

The lift arm will lower DOWN when the lever is pushed forward.

3. Float:

NOTE: There is no detent or float position on the bucket dump and curl circuit.

To place the lift arm in Float, push the control lever all the way forward until a slight jump is felt. The lever will remain in this position until pulled back and out of detent. (toward neutral) In this detented, FLOAT position, the lift arm will float over changing ground contour.

58

TRIM THIS EDGE LEFT PAGE Bur 87364592na

INSTRUMENTS/CONTROLS

Instructional Decals For ISO Pattern Steering And Controls A

B

TRIM THIS EDGE

C

87573274 / 87573277 / 87573278

See the control lever application decals on the machine and understand the functions before starting the machine or beginning any operation. Decal (A) shown above, is located on the left inside of the cab. Decal (B) is located on the inside left cab upright. Decal (C) is located on the inside right cab upright. If you have any questions about the operation or function of the control levers contact your Dealer.

59

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

INSTRUMENTS/CONTROLS

6

5

BD04F041

BD04F040

6. 2 Speed Control Button:

7. Ride Control Button:

Located on front side of left control lever (if equipped).

Located on front side of right control lever (if equipped).

Travel Speeds TRIM THIS EDGE

450 Low ........ 0 to 6.2 mph (0 to 10.0 km/h) High ..... 0 to 11.3 mph (0 to 18.1 km/h) 450CT Low................... 0 to 5.1 mph (0 to 8.2 ) High........ 0 to 8.0 mph (0 to 12.8 km/h) 465 Low ........ 0 to 6.2 mph (0 to 10.0 km/h) High...... 0 to 11.3 mph (0 to 18.1 km/h)

60

TRIM THIS EDGE LEFT PAGE Bur 87364592na

INSTRUMENTS/CONTROLS

THROTTLE CONTROLS Hand Throttle

Foot Throttle

1

3

2 BD04C054

1. Hand Throttle: Move the hand throttle forward to increase the engine speed. To decrease the engine speed, move the hand throttle rearward.

The hand throttle should be used during most operation. The full throttle position allows for maximum hydraulic flow from the hydrostatic drive and equipment pumps for increased drive and loader speed and response. See Adjusting The Hand Throttle, page 155.

2. Foot Throttle: When the foot throttle pedal is depressed the engine speed is increased. By decreasing the pressure on the foot throttle pedal the engine speed is decreased.

3. Hand Throttle Decal

The foot throttle is used when the operator requires maximum control, such as maneuvering in ver y tight conditions.

NOTE: Position the hand throttle for the desired minimum engine speed when using the foot throttle.

251752A1

61

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

TRIM THIS EDGE

BD04D097

INSTRUMENTS/CONTROLS

LIFT ARM HYDRAULIC BYPASS CONTROL 1

2 BD04D094

3 BD04M051

2. LIFT ARM BYPASS CONTROL DECAL 3. LIFT ARM BYPASS CONTROL LEVER

1. LOADER LIFT CONTROL LEVER

TRIM THIS EDGE

Lift Arm Bypass Control: Non-Pilot Control Machines In the event that the electrical power is lost while the loader lift arms are in the raised position, the operator can manually override the loader circuit lockout and safely lower the loader lift arms to the ground.

IMPORTANT: Always check the surrounding area prior to lowering the loader lift arms. Keep all other people out of the area.

While pushing the Hydraulic Bypass Lever to the right, use the left hydraulic control lever to lower the loader lift arms to the ground. When the Hydraulic Bypass Lever is released the loader hydraulic circuit is once again in the lockout function.

2

251762A1

62

TRIM THIS EDGE LEFT PAGE Bur 87364592na

INSTRUMENTS/CONTROLS Lift Arm Bypass Control: Pilot Control machines

WARNING: The Lift Arm Bypass Controls for Pilot Control and Non-Pilot control machines are ACTIVE at all times. Make sure the machine is clear of all personnel and objects or obstructions before engaging this control. Only engage this control while seated in the cab with the seat belt fastened and the restraint bar down. Failure to follow these instructions can result in death or serious injury.

For pilot control machines the lift arm bypass knob is located to the right of the operator and behind the console.

TRIM THIS EDGE

1

1C_002

1. LIFT ARM BYPASS CONTROL KNOB PILOT CONTROL MACHINES

1. Lift Arm Bypass Control:

87568435

Use this lever only if the machine has lost engine power and the loader arms are in the up

position.

Before attempting to lower the lift arms on a machine that has lost engine or electrical power, alert personnel in the area of your intention. Do not leave the seat, raise the restraint bar or unfasten the seat belt.

Slowly, pull the knob up to lower the lift arms.

63

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

INSTRUMENTS/CONTROLS

AUXILIARY HYDRAULIC ATTACHMENT CONTROL PEDAL

1

TRIM THIS EDGE

2

3

1. AUXILIARY HYDRAULIC CONTROL PEDAL 2. AUXILIARY HYDRAULIC FLOW CONTROL PEDAL DECAL 3. PEDAL IN ON POSITION

BD04D105 / BD04D101 / BD04D102

WARNING: Always relieve hydraulic pressure before attaching or removing auxiliary hydraulic attachments.

To relieve pressure: 1. Turn off engine.

2. While sitting in the seat, with the seat bar down, turn key switch to ON position.

3. Push the brake release button.

4. Actuate auxiliary controls switch in both directions several times.

5. Turn key switch to OFF. 64

TRIM THIS EDGE LEFT PAGE Bur 87364592na

INSTRUMENTS/CONTROLS This pedal controls the hydraulic flow to the front att achment (hydraulic couplers on the left loader arm). Push down either the left or the right side of the pedal, depending on the direction of flow required. When foot pressure is removed from the pedal it will return to the OFF position.

4

NOTE: If the attachment operates opposite than described, reverse the two hose connections at the attachment and mark the hoses to avoid further confusion.

BD04D101

4. AUXILIARY HYDRAULIC FLOW CONTROL PEDAL IN THE OFF POSITION

If the attachment requires continuous hydraulic power, depress the foot pedal in the desired direction with one foot and move the locking lever in the same direction with the other foot. This will hold the pedal in place. The pedal can be locked in either direction.

IMPORTANT: Always read the auxiliary attachment manual before making the hydraulic connections and operating the attachment.

NOTE: With pedal depressed to the right, oil will flow out of the male coupler, of the units auxiliary connectors.

NOTE: Always clean hydraulic hose couplers prior to making connections.

1

BD04M059

1. AUXILIARY HYDRAULIC HOSE COUPLERS (450 SHOWN)

65

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

TRIM THIS EDGE

To release the pedal, push the lock back to the center and the pedal will return to the OFF position.

INSTRUMENTS/CONTROLS Hydraulic hose couplers are provided on the left loader lift arm.

2

BD04C035

2. AUXILIARY HYDRAULIC HOSE, CASE DRAIN COUPLER

TRIM THIS EDGE

NOTE: If the attachment operates opposite than described, reverse the two hose connections at the attachment and mark the hoses to avoid further confusion.

NOTE: If it is necessary to get out of the cab with hydraulic flow to an attachment, it will be necessary to engage the Auxiliary Hydraulic Interlock Override switch on the instrument cluster to prevent the engine from stopping before leaving the seat or raising the restraint bar. After pushing the button, the lamp next to the button will flash, indicating that the override is activated and the operator may leave the cab. If the operator does not leave the cab within 30 seconds the override will reset.

66

TRIM THIS EDGE LEFT PAGE Bur 87364592na

INSTRUMENTS/CONTROLS

AUXILIARY ELECTRO-HYDRAULIC CONTROLS (If Equipped) Attachment electro-hydraulic controls a r e fo r S t a n d a r d o r H i g h F l o w configurations.

IMPORTANT: Always read the auxiliary attachment manual before making the hydraulic connections and operating the attachment.

Use the rocker switches on the left hand control lever to either activate the system or deactivate and control flow direction.

NOTE: Always clean the hydraulic couplers prior to making connections.

Hydraulic couplers are provided on the left loader lift arm.

If constant flow is desired, use the top switch.

1

2

7

6

BD04M058

3

450 CONFIGURATION

4

6. CASE DRAIN COUPLER 7. HIGH FLOW HYDRAULIC COUPLERS

5

Push the rocker switch to the OFF position before installing or removing any attachment.

BD05H096

1. OFF 2. ON (DETENT) - MALE COUPLER ENERGIZED 3. ON (MOMENTARY) - FEMALE COUPLER ENERGIZED 4. OFF 5. ON (MOMENTARY) - MALE COUPLER ENERGIZED

NOTE: Contact your Dealer if you have any questions concerning auxiliary hydraulic features on your machine.

67

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

TRIM THIS EDGE

If intermittent flow is desired, use the lower switch.

INSTRUMENTS/CONTROLS

WARNING: Always relieve hydraulic pressure before attaching or removing auxiliary hydraulic attachments.

To relieve pressure:

1

2

1. Turn off engine.

2. While sitting in the seat, with the seat bar down, t u r n key sw i t c h t o O N position.

3. Push the brake release button.

BD05H096

1. LEFT TURN SIGNAL SWITCH 2. RIGHT TURN SIGNAL SWITCH

4. Actuate auxiliary controls switch in both directions several times.

Turn Signal Switch:

TRIM THIS EDGE

If equipped, use this three way switch to signal left or right. Push the top portion of the switch to activate the left turn signal. Push the bottom portion of the switch to activate the right turn signal. The mid portion of the switch is off.

5. Turn key switch to OFF.

68

TRIM THIS EDGE LEFT PAGE Bur 87364592na

INSTRUMENTS/CONTROLS

OPERATOR’S SEAT Deluxe Seat (If Equipped)

4

3 TRIM THIS EDGE

2

1

BD04E078

1. Forward/ Rearward Adjustment Lever: Move the forward/rearward adjustment lever to the right and slide the seat to the most comfortable position. Release the lever.

2. Seat Suspension Control Knob: While sitting in the operators seat turn this knob to either increase or decrease the seat suspension. As the knob is moved, the indicator arrow will move along the graduated scale showing operator weight settings.

3. Lumbar Adjustment Control Knob: Turn this knob clockwise to increase the lumbar support. To decrease the lumbar support turn the knob counterclockwise.

4. Backrest Tilt Control Knob: Turn the knob clockwise to tilt the operators seat forward. Turn the knob counterclockwise to tilt the operators seat back.

NOTE: The Standard seat will feature the Forward/Rearward Adjustment Lever only and the location is identical for both Standard and Deluxe seats.

69

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

INSTRUMENTS/CONTROLS

AIR LOUVERS The louvers in this cab are adjustable and can be completely closed.

A

A

TRIM THIS EDGE

BD04E077

There are four rectangular louvers located above the operator’s seat on the head liner. The other two round louvers are located on each side of the operator and towards the front of the cab. These louvers are adjustable by tilting them in one direction or the other.

The two louvers behind the headliner (A) are re-circulation vents.

AUXILIARY POWER SUPPLY (IF EQUIPPED)

A 12 volt power supply when the key switch is in System Power (Accessory) or RUN position.

1

A_AUX_PWR

1. AUXILIARY POWER SUPPLY

70

TRIM THIS EDGE LEFT PAGE Bur 87364592na

INSTRUMENTS/CONTROLS

CAB DOOR LATCHES (IF EQUIPPED) 2 1 3

BD01D805

BD01D802

Push button on the outer cab door latch (1) to release and pull on handle to open cab door.

Lift handle on inner cab door latch (2) to release and push on grab bar (3) to open cab door.

IMPORTANT: Do not raise or lower loader lift arms with door not fully closed or damage will occur to the door assembly.

NOTE: To operate the loader functions without the front door installed you must install diode L71879 in the wiring harness. The diode should be installed in place of the molded plug in the front door harness connected to the to the plug on the cab harness. The harness is located under the ROPS toe guard. The diode is stored in the Operators Manual storage box when not in use.

SLIDING SIDE WINDOWS (IF EQUIPPED) The sliding side windows (if equipped) are opened by using the latch handle located on front of the window. Grasp the handle and push in on the release tab while sliding the window back to the desired position. Push forward on the handle to the latched position to close the window.

1

BD01C224

1. SLIDING WINDOW LATCH HANDLE

71

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

TRIM THIS EDGE

2. INNER CAB DOOR LATCH 3. GRAB BAR

1. OUTER CAB DOOR LATCH

INSTRUMENTS/CONTROLS

WINDSHIELD WASHER CONTROLS The windshield washer controls are located on the inside of the cab door.

2

1 4

3

BD01D801

BD01D803

4. WINDSHIELD WASHER RESERVIOR

TRIM THIS EDGE

1. OFF POSITION 2. ON POSITION 3. WINDSHIELD WASHER POSITION (MOMENTARY)

1. Windshield Washer Control Switch: When the switch is pressed to the left side of the switch to the MOMENTARY (3) position, washer fluid is sprayed on the front windshield.

BS99N054

BS99N055

2. Windshield Wiper Switch: The windshield wiper switch has three positions, (1) ON, (2) OFF, MOMENTARY (Windshield Washer) (3). Push the switch to the left to the ON (2) position for wiper function. Push the switch to the MOMENTARY position (3) for windshield washer function. Push the switch to the right to the OFF (1) position to stop the wiper.

DOME LAMP CONTROLS The deluxe cab dome lamp is located above the operators seat.

1

Move the switch either left or right to tur n the dome lamp on. When the switch is in the center position, the dome lamp is OFF. The Key Switch must be in the RUN or accessor y position for the dome lamp to work.

BD04E079

1. DOME LAMP

72

TRIM THIS EDGE LEFT PAGE Bur 87364592na

INSTRUMENTS/CONTROLS

AUXILIARY ELECTRICAL SWITCH Four auxiliary electrical switches are located on the optional right control lever. The switches control functions of the auxiliary front electrical connector.

The top three switches are momentary.

The bottom right switch has a detent for ON and OFF. Consult your dealer to identify which pins in the connector are controlled by each switch.

BD01C239

TRIM THIS EDGE

1. AUXILIARY ELECTRICAL SWITCHES

73

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

INSTRUMENTS/CONTROLS

NOTES

TRIM THIS EDGE 74

TRIM THIS EDGE LEFT PAGE Bur 87364592na

OPERATING INSTRUCTIONS DAILY INSPECTION Do the following each day before you s ta r t t h e e n g i n e a n d o p e ra t e t h e machine.

When the seat bar is in the UP position, the brake should be engaged with ground dr ive pumps in neutral, p r ev e n t i n g f o r w a r d / r e a r w a r d movement of the machine and locking out the hydraulic system, preventing movement of the loader lift arms and bucket.

1. Check the machine for leaks.

Repair all leaks and clean the area with solvent, or pressure wash using soap and water.

2. Check the tires for damage.

Check the operation of the seat restraint bar:

3. Check for damaged, loose, or missing parts. Replace, tighten, or adjust as req uired b efore you operate the machine.

4. Clean all debris from the machine, especially around the engine and radiator.

2. With the engine stopped and the key switch in the OFF position, the control handles should be locked to prevent side to side movement.

Tur n the key switch to the ON position, press the par k brake switch and the control handles should move.

5. Clean or replace any safety or instructional decals that cannot be read.

6. Clean the hand holds, steps, and operators compartment. Remove all loose items from the machine.

3. Start the engine and raise the seat bar to the full UP position.

7. See the Lubrication and Maintenance Chapters in this manual. Complete the procedures in the section marked Every 10 Hours of Operation beginning on page 119.

4. Move the steering control levers fore and aft. If the machine will move do the following: A. Stop the engine.

8. If this is a new machine, or a machine with a new or rebuilt engine, see Run-In Period on page 79.

75

TRIM THIS EDGE RIGHT PAGE (Section First Page) Bur 87364592na

TRIM THIS EDGE

1. Sit in the operators seat, fasten the seat belt and lower the seat restraint bar.

OPERATING INSTRUCTIONS

1 3 2 BD04M006

1. SEAT BAR PLUNGER SWITCH 2. SWITCH PLUNGER BD04M007

TRIM THIS EDGE

B. Locate and inspect the seat restraint bar plunger switch located to the left, behind the operator seat. With the seat restraint bar in the fully raised position, the plunger on the switch should be extended and not make contact with the contact pad welded on the seat restraint bar as shown.

3. CONTACT PAD

C. With the seat restraint bar in the fully lowered position, the contact pad on the seat restraint bar should contact the plunger of the switch and move it into the switch as shown.

NOTE: The pad on the seat restraint bar should not contact the housing of the switch.

IMPORTANT: If either of the positions of the switch are not as shown in the photos, contact your Dealer for corrective action.

Repeat steps 1 through 4.

ATTENTION: If the skid steer moves with the seat bar in the raised position while sitting in the seat, contact your Dealer.

76

TRIM THIS EDGE LEFT PAGE Bur 87364592na

OPERATING INSTRUCTIONS Test the Operator’s Seat Presence Switch: 1. Sit in the operators seat with the seat bar in the down position.

2. Start the engine.

3. The Park lamp symbol should be illuminated.

4. Push the Park Brake switch symbol on the control panel below the warning lights. The Park light will extinguish and the brakes will release, the ground drive pumps will be activated, and the loader hydraulic control spools will be operational.

TRIM THIS EDGE

5. Carefully lift your weight off of the seat without moving any of the control levers. The Par k Light should come on after approximately 1 to 2 seconds. The ground drive pumps should be disengaged, the brakes will apply, and the loader controls should be locked in neutral.

6. With your weight off the operators seat carefully try the loader hydraulic and steer ing control levers. They should be inoperative.

IMPORTANT: If the operators presence switch does not function as described, contact your Dealer.

77

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

OPERATING INSTRUCTIONS

STARTING THE ENGINE WARNING: Before you start the engine, read and understand the operator’s manual and the safety decals for this machine. ALWAYS fasten the seat belt and pull seat bar down. Make sure all other persons in the area are away from the machine.

SC004

WARNING: Before starting the engine, study the operator’s manual safety messages. Read all safety signs on machine. Clear the area of other persons. Learn and practice safe use of controls before operation. It is your responsibility to understand and follow the manufacturer’s instructions on machine operation, service, and to observe pertinent laws and regulations.

Operator’s and service manuals can be obtained from your dealer.

SB055

1. If equipped, turn the master battery disconnect switch to the ON position.

2. Adjust the seat and fasten the seat belt.

3. Pull the seat bar down.

TRIM THIS EDGE

4. Alert any person in the area that you are going to start the engine.

5. Push the throttle forward approximately 25 mm (one inch).

6. Turn the key switch to start.

7. Release the key switch when the engine has started.

78

TRIM THIS EDGE LEFT PAGE Bur 87364592na

OPERATING INSTRUCTIONS

PARKING THE MACHINE AND STOPPING THE ENGINE

1.Operate the machine with normal loads for the first 8 hours. Do not wo r k t h e e n g i n e h a r d a t s t a l l speeds (wheels turning slow or stopped and engine speed at full throttle).

1.Park on level ground whenever possible and lower the loader lift arms to the ground.

2.Keep the engine at normal operating temperatures.

IMPORTANT: If you must temporarily park the machine on a hillside, put the front of the machine toward the bottom of the hill. Make sure the machine is behind an object that will not move.

3.Do not run the engine at low idle speeds for long periods of time.

WHEEL NUTS

2.If the engine has been working at full load, run the engine at idle speed for two or three minutes to cool the engine parts evenly.

3.Turn the key to the OFF position to stop the engine.

If the machine is equipped with stamped center wheels, the lug nuts will be tapered type lug nuts.Tighten each lug nut to a torque of 135 to 163 Nm (100 to 120 pound-feet).

4.Move the loader controls until locked. Remove the key, raise the seat bar, and release the seat belt.

Always use the hand holds and steps when exiting the machine.

If the machine is equipped with solid center wheels, the lug nuts will be flange type lug nuts.Tighten each lug nut to a torque of 224 to 265 Nm (165 to 195 pound-feet).

NOTE: The parking brake is engaged automatically.

WARNING: Jumping on or off the machine can cause an injury.

Always face the machine, use the hand holds and steps, and get on or off the machine slowly. Do not rush.

HYDRAULIC FILTER

RUN-IN PERIOD

Replace the hydraulic filter after 20 h o ur s of u se if a m a jor hy draulic component has been replaced. See Hydraulic Oil Filter Replacement on page 141.

ENGINE

DRIVE CHAINS

During the first 20 hours of operation for a new machine, or if the engine has been rebuilt, adhere to the following procedure:

Adjust, if necessary, the drive chains after 250 hours of operation if the drive c h a i n s h ave b e e n r e p l a c e d . S e e Adjusting the Drive Chain Tension page 156.

SA038

79

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

TRIM THIS EDGE

If the machine is new or if a wheel is removed for service, check and tighten the wheel nuts tightness every two hours of operation until they remain tight.

OPERATING INSTRUCTIONS

OPERATING IN COLD WEATHER

3. LUBRICANTS: Use the correct viscosity oil in each component. As an example: SAE 30 engine oil at 0° C (32° F) increases the star ting load by about 250 percent.

M a k e s u r e y o u fo l l o w t h e recommended oil and filter service schedule as shown in this manual.

Cold weather conditions require specific procedures. During these conditions, your machine will require special attention to prevent serious damage. Check the following in cold weather:

4. DIESEL FUEL SYSTEM: Check with your fuel supplier for the correct cold weather fuel. Diesel engine power will be reduced if wax particles are in the fuel filter.

1. PREVENTING DAMAGE TO THE H Y D R O S TAT I C S Y S T E M I N COLD TEMPERATURES

TRIM THIS EDGE

Below 0° C (32° F), operate the engine at 1/2 throttle for 10 minutes with the controls in the NEUTRAL position. Do not operate the hydraulic cylinders rapidly or against the stops rapidly until the hydraulic oil is warm. Increase the engine speed to 3/4 throttle and move the control levers to 1/2 forward. Move the machine at no load for one minute.

Cold temperature operation can cause moisture condensation in the fuel tank.

Keep the fuel tank full and check for wa t e r f r e q u e n t l y. S e e F u e l Ta n k instr uctions, page 135. Failure to remove water from the fuel may result in an inoperative engine and damage to the fuel system.

2. BATTERY AND ELECTRICAL SYSTEM: Clean the battery and make sure the battery is at full charge. Inspect the battery cables and terminals. Clean and spray the terminals with battery terminal protector to prevent corrosion.

5. COOLING SYSTEM: Check the coolant mixture before you operate in cold temperatures. A mixture of 50% ethylene glycol and 50% water must be used in this machine. This mixture is used if the lowest ambient temperature is above -37° C (-34° F). If the ambient temperature is lower, adjust the mixture to 60% ethylene g l y c o l a n d 4 0 % w a t e r. I t i s recommended that ethylene glycol and water be used in your machine all year.

NOTE: A fully charged battery at -17° C (0° F) has only 40 percent of the normal starting power. When the temperature falls to -29° C (-20° F), the battery has only 18 percent of its power remaining.

If distilled water is added to the battery when the temperature is below 0° C (32° F), charge the battery or run the engine for approximately two hours.

This procedure will prevent battery freezing.

6. COLD TEMPERATURE STARTING AIDS: See your Dealer for extra starting aids such as block heaters or engine preheat cold start systems.

If your machine is equipped with an engine pre-heat system, turn the key switch to ON and wait until the pre-heat lamp goes out, before attempting to start the engine.

80

TRIM THIS EDGE LEFT PAGE Bur 87364592na

OPERATING INSTRUCTIONS

OPERATING IN HOT WEATHER To prevent damage to the machine during hot weather operation do the following: 1. Keep the coolant at the correct level in the coolant reservoir and radiator.

2. With the engine cold, check the radiator cap for damage before hot weather starts. Replace the cap as required.

TRIM THIS EDGE

3. Keep all dirt and debris from restricting the radiator and engine area. Clean the radiator and hy d r a u l i c c o o l e r o f t e n w h e n wo r king in ver y dusty or dir ty conditions.

4. Check the condition and tension of the fan belt.

5. Use lubricants of the correct viscosity as recommended in this manual.

6. Use the correct solution of 50% (maximum) ethylene glycol and 50% water in the cooling system.

7. Check the air cleaner dust valve frequently during extremely dusty conditions.

81

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

OPERATING INSTRUCTIONS

BOOSTER BATTERY CONNECTION WARNING: Wrong jumper cable connections or shorting across the starter terminals can cause the machine to move suddenly out of control.

You can be injured or killed. Use the correct method shown on this page to connect jumper cables to this machine.

50-38

You can jump start this machine at the battery, or at the remote jump star t terminals (if equipped).

6.Start the engine and disconnect the negative (-) jumper cable first and the positive (+) jumper cable last.

Jump Starting at the Battery 1.Lower the loader lift arms and attachment to the ground.

2.Remove the floor plate to gain access to the battery.

TRIM THIS EDGE

3.If another machine is used for power, make sure the two machines are not touching.

1

2 BD04C041

1. POSITIVE (+) JUMPER CABLE CONNECTION 2. MACHINE GROUND (-) JUMPER CABLE CONNECTION

4.Connect the positive (+) jumper cable to the positive (+) battery terminal.

5.Connect the negative (-) jumper cable to the machine frame away from the battery.

82

TRIM THIS EDGE LEFT PAGE Bur 87364592na

OPERATING INSTRUCTIONS

Jump Starting at the Remote Jump Start Terminals (If Equipped) 1

3

1

3 2

2

BD04B099 / BD04M028

9. Disconnect the negative (-) (2) jumper cable first and the positive (+) (1) jumper cable last.

1. POSITIVE (+) REMOTE JUMP START TERMINAL 2. NEGATIVE (-) REMOTE JUMP START TERMINAL 3. BATTERY MASTER DISCONNECT SWITCH

10. Replace the protective caps on the remote jump start terminals and close the rear access door.

1. Lower the loader lift arms and attachment to the ground.

2. Open the rear access door.

3. If another machine is used for p o w e r, m a k e s u r e t h e t w o machines are not touching.

4. Remove the protective caps from the positive (+) (1) and negative (-) (2) remote jump start terminals.

5. Connect the positive (+) jumper cable to the positive (+) (1) remote jump start terminal.

6. Connect the negative (-) jumper cable to the negative (-) (2) remote jump start terminal.

7. Turn the battery master disconnect switch (3) to the ON position.

8. Sit in the operators seat and use the key switch to start the engine.

83

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

TRIM THIS EDGE

465 - 450

OPERATING INSTRUCTIONS

MACHINE OPERATION WARNING: Before you operate the machine, check the steering control levers, instruments, warning lamps, engine throttle, and equipment hydraulic controls. Also check the restraint bar. When the restraint bar is in the UP position, the park brake light is illuminated, the parking brake is ENGAGED, the loader hydraulic circuit is inoperative and the ground drive is disabled.

If you know there is a malfunction, a missing part, or a part that needs adjustment, stop the machine and correct the problem immediately.

Failure to follow these instructions can result in injury or death.

WARNING: DO NOT operate the machine while under the influence of alcohol or drugs.

CM122

TRIM THIS EDGE

1. Set the engine speed at desired throttle setting. Control the machine ground speed with the steering control levers.

4. Keep the work area as smooth and level as possible.

5. Select the correct tires for the conditions, that is; wide or narrow, pneumatic or non-pneumatic.

NOTE: Running the engine at idle speed for long periods can cause low operating temperatures. A low operating temperature can cause the formation of acids and deposits in the engine oil.

It is recommended you run the engine at full throttle when operating conditions permit.

JOB SITE OPERATION 1.Before starting work, familiarize yourself with the working area noting any holes, obstacles and debris that can be cleared from the site.

2.Locate any unavoidable danger areas (electric power lines, bridges, tight corners, etc.) and make sure you can work safely in these areas.

2. If you are a new operator, always operate the machine in an open area at a reduced machine ground speed until you get a feel for the controls. Move the steering control levers slowly and smoothly to avoid machine bouncing. If the machine does start bouncing, release the steering control levers and the machine will come to a stop.

3. Electric power lines, gas pipes, water pipes or other underground installations can cause injury or death. Find out about the location of underground installations before you operate your machine in a new area.

3. Keep all machine and loader movements smooth and the work cycle as short as possible. You can get more done in a shorter time with a smooth short work cycle.

4.Clear the area of any unauthorized personnel.

84

TRIM THIS EDGE LEFT PAGE Bur 87364592na

OPERATING INSTRUCTIONS

OPERATING THE LOADER Normal Use WARNING: When you operate, always keep all parts of your body inside the operators compartment. Then, before you leave the operators seat, always lower the loader bucket or attachment to the ground and stop the engine. You can be injured or killed if you do not follow these instructions.

SA010

WARNING: When you operate the machine, keep the loader bucket as low as possible. This low position gives better balance and permits you to see more clearly. If the bucket is full and you move the machine over ground that is rough or surfaces that can cause the machine to slide, always operate at slow speed. If you do not use this procedure, the machine can go out of control and roll-over.

WARNING: Raised equipment on the machine without an operator can cause injury or death. Before you leave the operators compartment, always support or lower the equipment (backhoe, blade, boom, bucket, etc.) to the ground and stop the engine.

SA044

Filling and Dumping the Bucket 1.Lower the lift arms against the stops, increase the engine speed to full throttle and enter the stockpile at about 1/4 speed.

3.Keep the load low while carrying it to the dump area.

BI97C110

4.At the dump site, keep all movements smooth when you raise and dump the bucket.

BI97C108

2.Roll back and raise the bucket.

BI97C109 BI97C111

85

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

TRIM THIS EDGE

SA041

OPERATING INSTRUCTIONS

WARNING: Impact Hazard: Bucket edge or teeth can catch on frozen surface or buried object during surface scraping operations. Before operation inspect the area for objects the bucket can catch on and mark them. During operation make sure the bottom of the bucket is level with the surface to be scraped. Operate the machine around the objects and at slow speed. Injury to the operator and damage to the machine can result if these precautions are not followed. Always fasten the seat belt.

M465

Operating on a Hillside or Ramp WARNING: Hillside operations can be dangerous. Rain, snow, ice, loose gravel, soft ground, etc., change the ground conditions. You must make a judgment if your machine can be safely operated on any hillside or ramp.

SB013

WARNING: When you are operating on a hill, be very careful. Do not turn the machine sideways to the bottom of the hill. The machine can roll over.

TRIM THIS EDGE

SA014

Load in the Bucket If you have a load in the bucket, drive the machine up the hill. With a load in the bucket, use reverse to back the machine down the hill.

BI97C112

BI97C113

Bucket Empty If the bucket is empty, drive the machine down the hill. Use reverse to back the machine up the hill when you have an empty bucket.

BI97C114

BI97C115

86

TRIM THIS EDGE LEFT PAGE Bur 87364592na

OPERATING INSTRUCTIONS

MANUAL ATTACHMENT COUPLER Installing a Bucket or Attachment IMPORTANT: Read the manufacturer’s instructions manual for attachments not included in this manual. DO NOT use attachments that are not approved. The use of additional equipment or accessories that are not authorized could invalidate CE compliance (applies to selected European countries for safety requirements).

3. Move the machine slowly forward and raise the loader lift arms. The 2 wedge shaped top edge of the attachment coupler must engage in the upper mounts of the bucket or attachment.

TRIM THIS EDGE

3

1

4 BD04M014

1. COUPLER LATCH PIN 2. ATTACHMENT LOCK LEVERS (SHOWN IN THE LOCK POSITION)

IMPORTANT: Before installing a bucket or attachment make sure the mounting area of the bucket, attachment and Case attachment coupler are clean.

Inspect the pin engagement areas for wear.

BK98E108

3. ATTACHMENT COUPLER LOCK LEVERS 4. COUPLER V ENDS

To Install a Bucket or Attachment: (bucket shown):

4. Roll the attachment coupler back while lifting the bucket or attachment off the ground. The attachment coupler will slide into position.

1. Make sure the attachment coupler lock levers are in the unlocked position.

5. Lower the bucket or attachment until it is 25 to 5 0 m m (1 to 2 inches) off the ground.

2. While sitting in the operators seat with the seat bar down, start the engine and tilt the attachment coupler forward.

6. Stop the engine and raise the seat bar.

87

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

OPERATING INSTRUCTIONS

BL98E109

BD04F046

7. Push both attachment coupler lock levers down securing the bucket or attachment in position.

It is the operators responsibility to confirm that the attachment or bucket are properly secured before operating the machine.

TRIM THIS EDGE

NOTE: If the attachment coupler lock levers do not lower into the LOCKED position, remove the attachment and investigate the cause.

BK98E088

ATTACHMENT LOCK LEVERS IN LOCKED POSITION

Before operating the machine, always inspect the coupler latch pin engagement into the attachment by raising the loader arms high enough to view the latch pin engagement from the operators seat.

88

TRIM THIS EDGE LEFT PAGE Bur 87364592na

OPERATING INSTRUCTIONS

Removing a Bucket or Attachment IMPORTANT: Read the manufacturer’s instructions manual for attachments not included in this manual. DO NOT use attachments that are not approved by Case.

The use of additional equipment or accessories that are not authorized by Case will invalidate CE certification to safety requirements.

1. Raise the bucket or attachment 25 to 50 mm (1 to 2 inches) off the ground.

BK98E086

5. Rotate the attachment coupler out (bucket dump function) allowing the bucket or attachment to slide off the top edge of the coupler.

BK98E087

3. Pull both attachment lock levers upward to disengage the bucket or attachment.

4. Return to the operators seat, lower the seat bar, fasten the seat belt and start the engine.

89

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

TRIM THIS EDGE

2. Stop the engine, raise the seat bar and release the seat belt.

OPERATING INSTRUCTIONS

HYDRAULIC ATTACHMENT COUPLER (IF EQUIPPED) Installing a Bucket or Attachment Engaging or disengaging the hydraulic coupler lock pins requires holding the righthand control lever over relief (holding the lever at its stop) and simultaneously pressing the hydraulic coupler switch. Practice this procedure before attempting to attach or remove a bucket or attachment.

NOTE: Any loader function held over relief will activate the coupler pins. Use the correct function for the attachment being installed.

Before Installing or Removing an attachment the Operator must: 1. Make sure the mounting area of the bucket, attachment and attachment coupler are clean. See the instructional decal located on the loader arm crosstube.

TRIM THIS EDGE 1. INSTRUCTIONAL DECAL LOCATED ON THE LOADER ARM CROSSTUBE

BD05C056 / 87460009

2

1C_009 / BD04C048

2. HYDRAULIC COUPLER SWITCH LOCATED ON THE LEFT-HAND CONSOLE 3. RIGHT-HAND CONTROL LEVER

90

TRIM THIS EDGE LEFT PAGE Bur 87364592na

OPERATING INSTRUCTIONS 2. Place the coupler lock pins into the disengaged position by holding the righthand control lever over relief in the full rollback position and engaging the unlock side of the hydraulic coupler switch.

4

4 5

4. COUPLER V ENDS 5. LOCK PIN INDICATORS SHOWN IN THE RED DISENGAGED POSITION

BD04F037

3. Slowly approach the bucket or attachment with the coupler V ends, as shown, until engaging the bucket or attachment.

BD04F038

91

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

TRIM THIS EDGE

5

OPERATING INSTRUCTIONS 4. After engaging the bucket or attachment slowly rollback the bucket or attachment to the full rollback position. Hold the right-hand control lever over relief, in the rollback position, and activate the lock side of the hydraulic coupler switch until the lock pins engage.

NOTE: When the bucket is rolledback the Lock Pin Indicators will lower and may become obscure to some operators, depending on their height.

6

6

TRIM THIS EDGE

8

7

BD04M052 / BD04F035 / BD04F034

6. GREEN LOCK PIN INDICATORS 7. COUPLER LOCK PIN ENGAGED 8. COUPLER LOCK PIN DISENGAGED

5. Curl or roll the bucket or attachment out to view the Lock Pin Indicators. Only Green should be seen, as shown in above photo.

6. Slowly raise the bucket or attachment to confirm that the Lock Pins are engaged.

92

TRIM THIS EDGE LEFT PAGE Bur 87364592na

OPERATING INSTRUCTIONS

Removing the Bucket 1.Raise the bucket or attachment 25 to 50 mm (1 to 2 inches) above the ground.

BD04C048

TRIM THIS EDGE

2. Hold the Right Control Lever over to the bucket roll back position and over relief while pushing the unlock side of the hydraulic coupler switch.

Release the control lever prior to releasing the switch.

3. Rotate the attachment coupler out (bucket dump function) allowing the bucket or attachment to slide off the top edge of the coupler.

93

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

OPERATING INSTRUCTIONS

HIGH FLOW HYDRAULIC SYSTEM Gear Pump 204 Bar (3000 PSI) High Flow System The gear pump 204 Bar (3000 psi) High Flow system supplies more flow than the auxiliary hydraulics, which allows the use of attachments designed for this pressure and flow.

The High Flow System should be used as follows: 1. Install the attachment, following the manufacturers instructions.

2. Connect the attachment hydraulic hoses to the High Flow couplers located on the left side loader lift arms.

Use the rocker switches on the left hand control lever to either activate the system or deactivate and control flow direction.

If constant flow is desired, use the top switch.

2

If intermittent flow is desired, use the lower switch.

TRIM THIS EDGE

1

1

2

3 3

BD04C035

4

1. STANDARD FLOW AUXILIARY HYDRAULIC COUPLERS 2. CASE DRAIN COUPLER 3. HIGH FLOW HYDRAULIC COUPLERS

5 BD05H096

1. OFF 2. ON (DETENT) - MALE COUPLER ENERGIZED 3. ON (MOMENTARY) - FEMALE COUPLER ENERGIZED 4. OFF 5. ON (MOMENTARY) - MALE COUPLER ENERGIZED

94

TRIM THIS EDGE LEFT PAGE Bur 87364592na

OPERATING INSTRUCTIONS

Flow Rates Auxiliary Hyd Circuit .............. 21.9 gpm High Flow (combined) ........... 41.8 gpm

TRIM THIS EDGE

4

BD04E076

4. HIGH / LOW HYDRAULIC FLOW SWITCH

3. Turn the switch in the right-hand console to H for Hi Flow. Use L for Standard Flow.

NOTE: While in operation, the High Flow system can be turned off at any time using the High Flow switch located on the left - hand control lever.

95

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

OPERATING INSTRUCTIONS

RIDE CONTROL Ride Control is a feature that improves the machine ride over all types of terrain with either an empty or loaded bucket. Ride Control will reduce fore and aft pitching motion during transport and material hauling operations, while allowing increased productivity and operator comfort. It also reduces shock loads to the machine.

2

1

TRIM THIS EDGE

BD04F042 / 255927A1

1. RIDE CONTROL BUTTON

1. Ride Control: To activate the ride control feature, raise the loader lift arm off the chassis about 4 to 6 inches. Depress and hold the ride control button while “ride control” is desired. The ride control feature will allow the BS98M070 loader arms to float independent of the rest of the unit, therefore creating a smoother ride for the operator, and results in less material spillage from the bucket or forks. The ride control feature can also be used to eliminate tire “hop while counter rotating on hard surfaces. To stop the ride control feature, release the ride control button. For additional information on ride control accumulator, see page 158.

NOTE: When the ride control button is depressed, the loader lift arms may slightly raise or lower itself during initial activation, then will float according to the terrain being driven on.

2

BD01C076

2. RIDE CONTROL WARNING DECAL LOCATION

96

TRIM THIS EDGE LEFT PAGE Bur 87364592na

OPERATING INSTRUCTIONS

ANTI-VANDAL LOCKOUT When the upper engine access door is locked the entire engine compartment is no longer accessible. \

1

2 BD04D103

BD04D104

NOTE: Any brand of padlock will work as long as the shackle diameter is 6.35 mm (.25 in) and the shackle height is 44.45 mm (1.75 in) long.

MOVING A DISABLED MACHINE This machine must not be towed. If the machine is disabled and can not be repaired on the job site, lift the machine onto a trailer or truck. You can damage the hydrostatic system if you tow the machine. Contact your Dealer.

97

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

TRIM THIS EDGE

2. ANTI-VANDAL LOCKOUT LOCATION WITH LOCK INSTALLED. SEE NOTE BELOW

1. ANTI-VANDAL LOCKOUT LOCATION

OPERATING INSTRUCTIONS

TRANSPORTING THE MACHINE PRIOR TO LOADING WARNING: Know the rules, regulations, laws and safety equipment necessary for transporting or operating this machine on a road or highway.

Rotating Beacon, backup alarm, slow moving vehicle emblem and other safety equipment items are available from your dealer.

84-13A

WARNING: The machine can slip and fall from a trailer or ramp and cause injury or death. Make sure the trailer and ramp are not slippery. Remove all oil, grease, ice etc. Carefully move the machine off or onto the trailer with the machine centered on the trailer and ramp.

SB042

TRIM THIS EDGE

Observe all work site rules and local ordinances gover ning loading and transporting the machine. Ensure the h a u l i n g u n i t m e e t s a l l s a fe t y r e q u i r e m e n t s b e fo r e l o a d i n g t h e machine.

5.Fasten the machine to the trailer at the points indicated by the tie down decals.

2

1. Put a block at the front and rear of the trailer or truck wheels.

2. Carefully back the machine slowly onto the trailer.

3. Lower the loader lift arms to the trailer deck, stop the engine, and remove the key.

BP96N125

2. FRONT TIE DOWN LOCATIONS

4. Put a block at the front and rear of each machine tire.

6.Measure the clearance height of the machine and trailer or truck. Post the clearance height in the cab of the truck.

1

BD01C196

1. REAR TIE DOWN LOCATION (ONE EACH SIDE)

139728A1 TIE DOWN LOCATION DECAL

98

TRIM THIS EDGE LEFT PAGE Bur 87364592na

OPERATING INSTRUCTIONS

Craning the Machine WARNING: Only personnel with machine lifting experience should attempt craning the skid steer. Death or serious injury may result.

To crane the skid steer use only, chain, straps or cable with a rated capacity to handle the weight of the model skid steer being craned.

Refer to the Specifications Section of this manual for the operating weight of the model skid steer being craned.

Page 174

TRIM THIS EDGE

WARNING: The cumulative weight of the chains, straps, cables or other lifting devices must be added to the total weight being craned.

When lifting these machines with a crane, use a four leg sling with a 39 degree sling angle. Each leg of the sling must have a minimum length of 1.8 m (6 ft).

2 BD04D089 / BD04M032 / BD04D091

LIFT HOOK LOCATIONS 2 EACH SIDE

1

WARNING: Remove all attachments before craning the skid steer.

Contact your Dealer for any questions that involve craning the machine.

BT97F064

IMPORTANT: Improper craning and improper craning devices could damage the machine.

1. 1.8 M (6 FEET) 2. FOUR LEG SLING

99

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

OPERATING INSTRUCTIONS

NOTES

TRIM THIS EDGE 100

TRIM THIS EDGE LEFT PAGE Bur 87364592na

WHEEL AND TIRES WARNING: Exploding tires and/or rim parts can cause injury or death.

Keep yourself and others out of the DANGER AREA. Stand on the tread side of the tire. Always use the correct air pressure and follow the instructions in this manual for adding air or servicing the tires.

TRIM THIS EDGE

SD020

BS97F041

The above illustrations show danger areas caused by exploding tires and/or rim parts. KEEP YOURSELF AND OTHERS OUT OF THESE DANGER AREAS. The next page shows the correct methods that you must use when adding air or servicing a tire.

101

TRIM THIS EDGE RIGHT PAGE (Section First Page) Bur 87364592na

WHEELS AND TIRES

WARNING: DO NOT weld to wheel or rim when a tire is installed. Welding will cause an explosive air/gas mixture that will be ignited with high temperatures. This can happen to tires inflated or deflated. Removing air or breaking bead is not adequate. Tire MUST be completely removed from the rim prior to welding.

SB134

WARNING: Explosive separation of the tire and/or rim parts can cause injury or death. When tire service is necessary, have a qualified tire mechanic service the tire.

84-113

Tire Pressures Check the air pressure and the condition of the tires every 50 hours of operation.

10 x 16.5 ....................................................................... 275 -344 kPa (40 - 50 psi) 12 x 16.5 ........................................................................ 241 - 310 kPa (35 -45 psi) 13 x 16.5 ....................................................................... 206 - 275 kPa (30 - 40 psi) 15.50 x 16.5 ................................................................. 172 - 341 kPa (25 - 35 psi) TRIM THIS EDGE

Inflating the Tire Always have a qualified tire mechanic ser vice the tires and r ims on this machine. It is recommended that you have this mechanic inflate the tires. To p r eve n t a c c i d e n t s, a l way s u s e a restraining device (tire inflation cage), correct equipment, and correct procedure. Explosive separation of the tire can cause serious injury.

If the tire has lost all the pressure or service to the tire or rim is required, do the following: BS99N137

1. Before you add air, have the tire correctly installed on the machine or put the tire in a restraining device (tire inflation cage).

2. Wear face protection and use an air hose with remote shut-off valve and a self-locking air chuck.

102

TRIM THIS EDGE LEFT PAGE Bur 87364592na

WHEELS AND TIRES 3. Stand behind the tread of the tire and make sure all persons are away from the side of the tire before you start to add air.

4. Inflate the tire to the recommended air pressure. DO NOT inflate the tire more than the recommended pressure.

Wheel Nuts If the machine is new or you have just installed the wheels, check the wheel nuts every 2 hours until the nuts remain tight.

If the machine is equipped with solid center wheels, the lug nuts will be flange type lug nuts.Tighten each lug nut to a torque of 224 to 265 Nm (165 to 195 pound-feet).

When installing tires, make sure that the tread is in the same direction.

103

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

BD01C268

TRIM THIS EDGE

If the machine is equipped with stamped center wheels, the lug nuts will be tapered type lug nuts.Tighten each lug nut to a torque of 135 to 163 Nm (100 to 120 pound-feet).

WHEELS AND TIRES

NOTES

TRIM THIS EDGE 104

TRIM THIS EDGE LEFT PAGE Bur 87364592na

LUBRICATION / MAINTENANCE WARNING: Improper service or repair can cause injury or death. If you do not understand the service procedures for this machine, see your dealer or the service manual for this machine.

SC021

Before you service the machine, put a Do Not Operate tag on the instrument panel. One Do Not Operate tag, is i n c l u d ed w i th yo ur n ew m ac h i ne.

Additional tags, part number 321-4614, are available from your Dealer.

321-4614

WARNING: Always use the loader lift arm lock when servicing the machine with the lift arms raised. Failure to do so can result in death or serious injury if the loader lift arms are lowered accidently.

Use the correct safety clothing and safety equipment. Understand how to use a fire extinguisher and first aid kit.

B770996R

Spare parts must meet specifications. Use parts supplied by your authorized Dealer to ensure guarantee of quality.

WARNING: When handling lubricants (oil, grease etc.), and other chemical products, always follow instructions for their proper use. Use proper containers to collect fluid. Dispose of fluids and filters responsibly and in accordance with the law. DO NOT smoke or use an open flame during the service procedure. Use eye protection. DO NOT run the engine or transmission when the engine or transmission oil temperatures exceed 120° F (49° C).

M1159

105

TRIM THIS EDGE RIGHT PAGE (Section First Page) Bur 87364592na

TRIM THIS EDGE

Read the safety decals and information decals on the machine. Read the operators manual. Read the AEM Safety Manual provided on Nor th American. machines. Understand the operation of the machine before you start servicing.

LUBRICATION

465 LOADER LIFT ARM LOCK PIN Engaging the Loader Lift Arm Lock Pin IMPORTANT: If an attachment is being used, the attachment should be removed before the loader lift arms are raised.

1. While sitting in the operator’s seat, with the seat bar down, start the engine and roll the coupler attachment all the way back.

2. Raise the loader lift arms to full height.

TRIM THIS EDGE

BD04087

A_PIN

LOCK PIN LEVER CONTROL LEVER (SHOWN ENGAGED)

LOADER LIFT ARM LINK RESTING AGAINST THE LOCK PIN

3. Engage the loader lift arm lock pin, using the lock pin control lever located in the right rear corner of the operator’s compar tment, by moving the lever toward the center of the machine.

4. Lower the loader lift arms until the loader lift arm link rests against the lock pin.

256356A2

LOADER LIFT ARM LOCK DECAL

BD04E072

LOCK PIN (SHOWN ENGAGED)

This will place the lock pin in the position shown above.

106

TRIM THIS EDGE LEFT PAGE Bur 87364592na

LUBRICATION

Disengaging the Loader Lift Arm Lock Pin 1. While sitting in the operator’s seat, with the seat bar down, start the engine and raise the loader lift arms until the loader lift arm link is no longer contacting the lock pin.

BD04D086 BD04E073

LOCK PIN IN STORAGE POSITION

L ow e r t h e l o a d e r l i f t a r m s t o t h e ground.

107

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

TRIM THIS EDGE

2. To disengage the lock pin, move the lock pin control lever toward the r i g h t s i d e o f t h e m a c h i n e, a s shown.

LUBRICATION

450 - 450CT LOADER LIFT ARM SUPPORT STRUT WARNING: If you service the machine with the loader lift arms raised, always use the cylinder lock support strut to block up the loader lift arms.

Failure to follow this procedure can cause serious injury or death if the loader lift arms are lowered by accident.

SC018

IMPORTANT: Installing the Support Strut can be performed as a one or two person procedure so that the operator is not entering the operators compartment under unsupported loader lift arms.

Installing the Support Strut: 1. Lower the loader lift arms to the ground and stop the engine.

TRIM THIS EDGE

BD04M021

BD04M022

2. Remove the pin from the support strut.

3. After the pin is removed, lower the support strut onto the lift cylinder.

4. Start the engine and slowly raise the loader lift arms until the support strut is on the lift cylinder rod.

Lower the loader lift arms until the support strut makes contact with the lift cylinder tube. Stop the engine.

BD04M023

5. Install the pin in the support strut.

108

TRIM THIS EDGE LEFT PAGE Bur 87364592na

LUBRICATION Storing the Support Strut IMPORTANT: Storing the Support Strut should be performed as a two person procedure so that the operator is not exiting the operators compartment under unsupported loader lift arms.

1. Have the operator enter the operators compartment and start the engine. Raise the loader lift arms approximately 1 to 2 inches (25 to 55 mm).

BD04M023

2. Stop the engine. Make sure the loader controls are locked. Do not exit the operators compartment.

Have a second person remove the support strut pin.

4. Have the operator start the engine and lower the loader lift arms to the ground. Stop the engine.

109

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

TRIM THIS EDGE

BD04M024

3. Have a second person raise the support strut to the storage position and install the pin. After installing the pin the second person should move away from the machine.

LUBRICATION

TILTING THE OPERATORS COMPARTMENT FORWARD You can tilt the operators compartment with the loader lift arms in the raised position or the fully lowered position. When the loader lift arms are in the raised position, unobstructed access to the engine, hydrostatic pumps, motors and control linkage is provided. With the loader lift arms in the lowered position, the loader arm lubrication points are accessible.

IMPORTANT: If an attachment is being used, the attachment should be removed before the loader lift arms are raised.

TRIM THIS EDGE

BD02E090X

CAB TILTED WITH LOADER LIFT ARMS RAISED

BD02E089X

CAB TILTED WITH LOADER LIFT ARMS LOWERED

IMPORTANT: See Loader Lift Arm Lock Pin on page 106 or Loader Support Strut on page 108.

110

TRIM THIS EDGE LEFT PAGE Bur 87364592na

LUBRICATION

To Tilt The Cab:

1

BP96N086

BD04D080

1. Disengage the operator’s compartment lock pins by pulling the compartment lock levers (1) forward.

3. Gripping both front cab hand holds near the top, tilt the cab forward.

TRIM THIS EDGE

2

BK98E094

BP99N001

2. Tilt the operator’s seat forward.

4. Confirm that the cab is tilted completely forward and the cab hold open latch (2) is engaged, as shown.

111

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

LUBRICATION

LOWERING THE OPERATORS COMPARTMENT To lower the operators compartment into the working position: 1. Make sure all tools or other items have been removed from the interior of the chassis before the operators compartment is lowered.

1 BP96N086 BD04C054X

TRIM THIS EDGE

2. Release the cab hold open latch by pushing the lever (1) forward.

4. Tilt the operator’s seat into position and push firmly on the top of the seat back.

2

BD04D080

BP99N002

3. Gripping both front cab hand holds near the top, slowly lower the cab into operating position.

5. Push both cab release levers (2) into the LOCK position.

IMPORTANT: On pilot models use caution when closing ROPS to ensure the pilot control handles do not get caught on the ROPS seat plate.

112

TRIM THIS EDGE LEFT PAGE Bur 87364592na

LUBRICATION

ENGINE HOURMETER The engine hourmeter, which displays in hours and tenths of an hour, shows the actual hours the engine has run. Use the engine hourmeter to service your machine at the correct time intervals. See the “Lubrication/Maintenance Chart” page 118.

BD04E075

1. ENGINE HOURMETER

MAINTENANCE LUBRICATION SCHEDULE Service your machine at the intervals and locations given in the Lubrication/ Maintenance Charts using the recommended lubricants.

Follow the maintenance lubrication schedule for this machine to reach maximum life of the machine and attachments.

1

BD04C056

1. MAINTENANCE LUBRICATION DECAL

113

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

TRIM THIS EDGE

1

LUBRICATION

SYSTEMGARD LUBRICATION ANALYSIS PROGRAM Ask your Dealer about a Lubricant Analysis Program. Through this service, your lubricants are tested in an independent laboratory. You simply remove a sample of lubricant from your machine and send the sample to the laboratory. After the sample is processed, the laboratory will report back to you and guide you with maintenance requirements. A Lubricant Analysis Program can help support your equipment up time and provide you with a service that can pay back dividends when you trade for another piece of equipment.

ENVIRONMENT Before you service this machine and dispose of oil, fluids and lubricants, always remember the environment. Do not put oil or fluids into the ground or into containers that can leak. Check with your local environmental, recycling center or your Dealer for correct disposal information.

TRIM THIS EDGE 114

TRIM THIS EDGE LEFT PAGE Bur 87364592na

LUBRICATION

FLUIDS AND LUBRICANTS FUEL TANK Capacity 450 / 450CT ............................................................................78.3 litres (20.7 gal.)

465 ..........................................................................................76.4 litres (20.2 gal.)

Specifications ........................................................................................... #2 Diesel Grade #2 diesel fuel which meets ASTM and EMA requirements should be used in these machines.

See websites for American Society for Testing Materials International @www.astm.com and Engine Manufacturers Association @ www.enginemanufacturers.org for more information.

HYDRAULIC SYSTEM Capacity - Total System 450 / 450CT......................................64.4 litres (17.0 gal.)

Capacity - Total System 465 ...................................................66.2 litres (17.5 gal.)

Specifications .................................................................... SAE 10W-30 Engine Oil CHAIN COMPARTMENTS Capacity - Each Side ................................................................... 7.6 litres (8.0 qt.)

Specifications ..................................................................... SAE 10W30 Engine Oil BATTERY Quantity ................................................................................................ As required Specifications ................................................................................... Distilled water GREASE FITTINGS Quantity ................................................................................................ As required Specifications ........................................................................ molydisulfide grease ENGINE CRANKCASE OIL Capacity - with filter change ....................................................... 12 litres (12.7 qt.)

Specifications ...............................Case No. 1 API Service CI-4 Engine Oil 15W40 FINAL DRIVE GEAR OIL - CT Models Capacity - each side....................................................................... 0.58 qt. (0.55 L) Specification................................................... Case 135H EP 80W-90 or 85W-140

115

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

TRIM THIS EDGE

COOLING SYSTEM Capacity (Radiator plus Engine) .................................................... 17 litres (18 qt.)

Recovery Bottle ............................................................................... 2 litres (2.1 qt.)

Specifications ..................................................50% water and 50% ethylene glycol

LUBRICATION

ACCESS DOORS

1

BD04F072 A_LWLATCH

1. UPPER REAR ACCESS DOOR

Lift up at the arrow locations above to open the upper rear access door.

2. LOWER REAR ACCESS DOOR RELEASE LEVER

Pull up on the lever to open the lower access door.

TRIM THIS EDGE

3

BD04M030

UPPER REAR ACCESS DOOR OPEN BD04M020

To close the door push it back down.

3. LOWER REAR ACCESS DOOR OPEN

The upper rear door will give the operator access to:

The lower rear access door will give the operator access to:

●

hydraulic fill

●

radiator check and fill

●

engine oil check and fill

●

coolant reservoir

●

master disconnect switch (465)

●

hydraulic coolers

●

fuel fill

●

hydraulic oil level check

●

air filter

●

●

remote battery boost (if equipped 465)

master disconnect switch (450 450CT)

●

remote battery boost (if equipped 450 - 450CT)

116

TRIM THIS EDGE LEFT PAGE Bur 87364592na

LUBRICATION

4

3597

TRIM THIS EDGE

4. ACCESS DOOR FOR TRACK TENSION GREASE FITTING (1 EACH SIDE)

117

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

LUBRICATION

LUBRICATION/MAINTENANCE CHART

103 Wheel Nut Torque 102 Tire Pressure

REPLACE

CLEAN

CHECK

LUBRICATE

SERVICE POINTS

INITIAL

PAGE NUMBER

SERVICE INTERVAL IN HOURS

AR AR

119 Loader Lift Arm, Bucket Pivots, Attachment Coupler Pins 123 Engine Oil Level

10 10

124 Hydraulic Res Oil Level 125 Hydraulic Oil Cooler

10

126 Engine Coolant Reservoir 126 Seat Restraint Bar Function

10

128 Operator’s Seat Presence Switch 129 Clean Tracks and Track Components

10

10 10 10

TRIM THIS EDGE

129 Initial Track Tension Check 129 Track Tension Check

10

131 Initial Final Drive Check and Change 132 Attachment Coupler Latch Handle / Attachment Coupler Wedges

100

50 250

134 Battery Fluid Level/Clean 135 Radiator Coolant Level

250

135 Drain Water from the Fuel Filter 156 Drive Chain Tension

250

250 250

136 Spark Arresting Muffler (If Equipped) 137 Final Drive

250 250

136 Check Chain Tank Oil 138 Engine Oil and Filter

250 500

144 Change Final Drive Oil 141 Fan Belt Tension

500

500

139 Fuel Filters Primary and In-Line 141 ROPS

500

141 Hydraulic Oil Filter Replacement 142 Mechanical Attachment Coupler

500

500 500

143 Coupler Attachment Fit-Up 145 Fuel Tank Water and Sediment

500 1000

146 Hydraulic Reservoir Oil 147 Check Engine Valve Clearance

1000

1000

147 Change Chain Tank Oil 148 Cab Air Cleaner Filter Elements

AR

1000

149 Engine Coolant 150 Engine Air Filter Elements

2000 2000

118

TRIM THIS EDGE LEFT PAGE Bur 87364592na

LUBRICATION

EVERY 10 HOURS OR DAILY 450 - 450CT Loader Lift Arm, Bucket Pivot Grease Fittings Use Molydisulfide Grease

7

1

8 2

10

9 11

3 4

BD04M012

7. BUCKET CYLINDER TO Z LINK (1 EACH SIDE) 8. Z LINK TO LOADER LIFT ARM (1 EACH SIDE) 9. Z LINK TO CHASSIS LINK (1 EACH SIDE) 10. LOADER LIFT ARM TO CHASSIS (1 EACH SIDE) 11. CHASSIS LINK TO CHASSIS (1 EACH SIDE)

5 6 12

BD04M011

3. ROD END BUCKET CYLINDER (1 EACH SIDE) 4. CONTROL LINK, UPPER END (1 EACH SIDE) 5. CONTROL LINK, LOWER END (1 EACH SIDE) 6. ROD END LIFT CYLINDER (1 EACH SIDE)

BK97E013

12. LIFT CYLINDER CLOSED END (EACH SIDE)

119

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

TRIM THIS EDGE

BD04M010

1. BUCKET LINK TO BUCKET (1 EACH SIDE) 2. LIFT ARM TO ATTACHMENT COUPLER (1 EACH SIDE)

LUBRICATION

465 Loader Lift Arm, Bucket Pivot Grease Fittings (Every 10 Hours) 5

1

2

BP96N080 BD04M018

5. LIFT ARM TO H BAR (1 EACH SIDE)

TRIM THIS EDGE

1. BUCKET CYLINDER ROD END (1 EACH SIDE) 2. LIFT ARM TO ATTACHMENT COUPLER (1 EACH SIDE)

6 7

3 8 BP96N081

BD04M016

6. H BAR TO CHASSIS (1 EACH SIDE) 7. LIFT ARM TO CONTROL LINK (1 EACH SIDE) 8. LIFT CYLINDER HEAD END TO CHASSIS (ONE FOR EACH SIDE)

3. LIFT CYLINDER ROD END (1 EACH SIDE)

4

BD04M017

4. BUCKET CYLINDER ROD END (1 EACH SIDE)

120

TRIM THIS EDGE LEFT PAGE Bur 87364592na

LUBRICATION

Attachment Coupler Grease Fittings Attachment Coupler Latch Pin (Every 10 Hours)

1

BD04M014

TRIM THIS EDGE

1. ATTACHMENT COUPLER LATCH PIN

Use molydisulfide grease.

121

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

LUBRICATION

EVERY 10 HOURS OR DAILY Engine Oil Case No. 1, 15W-40, API Service CI-4, Engine Oil is recommended for use in this engine.

NOTE: Oil to be used should be based on the ambient temperature the machine will be operating in.

See the chart below for recommended viscosity at ambient temperature ranges.

NOTE: Do not put Performance Additives or other oil additive products in the engine crankcase. The oil change intervals given in this manual are according to tests with Case lubricants.

Oil Viscosity/Temperature Ranges

TRIM THIS EDGE BS99N019

If Case No. 1 is not used, a premium oil that meets API CI- 4 specifications must be used to maintain the 500 hour service interval.

122

TRIM THIS EDGE LEFT PAGE Bur 87364592na

LUBRICATION

EVERY 10 HOURS OR DAILY Engine Oil Level Specification........ 15W-40 Case No. 1 Check the engine oil level before you start the engine each day or before the start of each shift. Always check the oil with the engine stopped and when the machine is on level ground.

BD04C062

1. ENGINE OIL LEVEL DIPSTICK

Make sure the engine level dipstick is pushed completely down and pull out to check the oil level.

2

BD04C061

2. ENGINE OIL FILL LOCATION

If the oil level is below the ADD mark add oil. DO NOT raise the oil level above the Full mark.

123

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

TRIM THIS EDGE

1

LUBRICATION

EVERY 10 HOURS OR DAILY Hydraulic Reservoir Oil Level Check Specification.................................................................. SAE 10W-30 Engine Oil 1. Park the machine on a level surface and put the attachment on the ground when you check the oil level.

2. Clean the filler cap and the area around the cap to reduce the risk of contamination.

3. Slowly turn the filler cap 1/2 turn to relieve pressure in the reservoir.

D o n o t r e m o ve t h e c a p u n t i l pressure is relieved.

1

4. Remove the filler cap and add oil as required.

10W-30 Engine Oil is recommended.

TRIM THIS EDGE

WARNING: Fire Hazard: Do not smoke while filling the hydraulic reservoir. Do not fill near open flames.

BD04C064

1. HYDRAULIC OIL LEVEL SIGHT GAUGE

M476

The hydraulic oil sight gauge is located inside the lower rear access door on the left side.

IMPORTANT: The normal fluid level is at the midpoint of the sight gauge when the loader arms and bucket are resting on the ground.

5. Apply clean oil to the filler cap seal and install the filler cap.

NOTE: The hydraulic and hydrostatic systems use the same reservoir.

2

BD04B095

2. HYDRAULIC OIL FILL

124

TRIM THIS EDGE LEFT PAGE Bur 87364592na

LUBRICATION

EVERY 10 HOURS OR DAILY Hydraulic Oil Cooler

For High Flow Systems

1

2

BD04C065

2. RELEASE PIN

1. Push the radiator release latch to the right to release the radiator.

4. Pull the release pin, located on the bottom left of the radiator, to swing the secondary hydraulic cooler out.

3

BD04B097

2. Tip the radiator out to inspect or clean the hydraulic cooler.

3. Pull the bottom of the radiator out until it drops into the detent slots for additional clearance.

BD042M020

3. SECONDARY HYDRAULIC COOLER

5. Clean the radiator and coolers with soap and warm water. Flush with clean water.

125

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

TRIM THIS EDGE

BD04B096

1. RADIATOR RELEASE LATCH

LUBRICATION

EVERY 10 HOURS OR DAILY Engine Coolant Reservoir Check

Seat Restraint Bar And Interlocks Function

Specification.50% ethylene glycol and 50% water

Test the seat bar and loader/steering controls for correct operation.

Check the level of the coolant when the engine is stopped and the coolant is COLD.

When the seat bar is in the UP position, the brake should be engaged with ground dr ive pumps in neutral, preventing forward/rearward movement of the machine and locking out the hydraulic system, preventing movement of the loader lift arms and bucket.

DO NOT remove the radiator cap during this check.

1 TRIM THIS EDGE

BD04B102

1. ENGINE COOLANT RESERVOIR

The coolant level must be between the add and the full mark on the coolant reservoir bottle.

2

BD04F052

2. ENGINE COOLANT RESERVOIR FILL CAP

If the coolant level falls below the add mark, add the proper coolant solution of 50% ethylene glycol and 50% water.

126

TRIM THIS EDGE LEFT PAGE Bur 87364592na

LUBRICATION

EVERY 10 HOURS OR DAILY Lock For Loader And Steering Controls

B. Locate and inspect the seat restraint bar plunger switch located to the left, behind the operator seat. With the seat restraint bar in the fully raised position, the plunger on the switch should be extended and not make contact with the contact pad welded on the seat restraint bar as shown.

1. Sit in the operators seat, fasten the seat belt and lower the seat restraint bar.

2. With the engine stopped and the key switch in the OFF position, the control handles should be locked to prevent side to side movement.

Tur n the key switch to the ON position, press the brake switch and the control handles should move.

4. Move the steering control levers fore and aft. If the machine will move do the following:

3

A. Stop the engine.

BD04M007

3. CONTACT PAD

C. With the seat restraint bar in the fully lowered position, the contact pad on the seat restraint bar should contact the plunger of the switch and move it into the switch as shown.

1

NOTE: The pad on the seat restraint bar should not contact the housing of the switch.

2 BD04M006

1. SEAT BAR PLUNGER SWITCH 2. SWITCH PLUNGER

IMPORTANT: If either of the positions of the switch are not as shown in the photos, contact your Dealer for corrective action.

Repeat steps 1 through 4.

ATTENTION: If the skid steer moves with the seat bar in the raised position while sitting in the seat, contact your Dealer.

127

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

TRIM THIS EDGE

3. Start the engine and raise the seat bar to the full UP position.

LUBRICATION

EVERY 10 HOURS OR DAILY Testing The Operator’s Seat Presence Switch 1. Sit in the operators seat with the seat bar in the down position.

2. Start the engine.

3. The Park lamp symbol should be illuminated.

4. Push the Park Brake switch symbol on the control panel below the warning lights. The Park light will extinguish and the brakes will release, the ground drive pumps will be activated, and the loader hydraulic control spools will be operational.

TRIM THIS EDGE

5. Carefully lift your weight off of the seat without moving any of the control levers. The Par k Light should come on after approximately 1 to 2 seconds. The ground drive pumps should be disengaged, the brakes will apply, and the loader controls should be locked in neutral.

6. With your weight off the operators seat carefully try the loader hydraulic and steer ing control levers. They should be inoperative.

IMPORTANT: If the operators presence switch does not function as described, contact your Dealer.

128

TRIM THIS EDGE LEFT PAGE Bur 87364592na

LUBRICATION

EVERY 10 HOURS OR DAILY Clean Tracks And Components Periodically, and when the machine has been working in mud, the tracks, roller wheels, idler wheels, final drive sprocket area and guide teeth should be cleaned.

4 1 3

1.

2.

3.

4.

2

2

2

BD05C053

FRONT IDLER WHEEL (1 EACH SIDE) TRACK ROLLER WHEELS (4 EACH SIDE) REAR IDLER WHEEL (1 EACH SIDE) FINAL DRIVE SPROCKET (1 EACH SIDE)

Initial Track Tension Check 1

Check the track tension after the first 10 hours on a new machine or if new tracks have been installed.

Check the track tension every 50 hours of operation after the initial check.

Proper adjustment will increase the life of the track.

2

For this procedure the tracks, rollers, idler wheels and final drive sprockets must be clean of dirt and debris.

1. Park the machine on a firm, level surface.

2. The machine should be raised, blocked and supported properly, until the tracks are about 50.8 mm (2 in) off of the ground or floor.

BD05B033

1. FRONT CENTER ROLLER WHEEL 2. TOP INSIDE OF LOWER TRACK

3. Measure from the lower track top surface to the bottom of one of the center roller wheels.

Allowable track sag.....12-19 mm (0.470.75 inch)

129

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

TRIM THIS EDGE

2

LUBRICATION To I n c r e a s e o r D e c r e a s e Tr a ck Tension: Specification.......molydisulfide grease

3597

1. Remove the adjustment cover.

TRIM THIS EDGE 3595

2. To increase track tension add molydisulfide grease to the fitting.

3. To decrease track tension SLOWLY loosen the fitting. The grease is under extreme pressure.

4. Repeat the procedure for the other side.

130

TRIM THIS EDGE LEFT PAGE Bur 87364592na

LUBRICATION

INITIAL 100 HOURS Check and Change Final Drive Oil Specification.. Case 135H EP 80W-90 or 85W-140 Capacity ...................... 0.55 L (0.58 qt.)

3

After the first 100 hours of operation check and change the final drive fluid.

2

NOTE: Use 80W90 when temperatures are 35°C (95°F) or below.

Use 85W-140 when temperatures are 35°C (95°F) or above.

1. Park the machine on firm, level ground with the final drive to be checked and drained in the position shown below. Thoroughly clean the area around the plugs.

BD05H004

2. CHECK/FILL AND DRAIN PLUG IN THE DRAIN POSITION 3. SIDE PLUG

3. Position the machine so the check/ fill and drain plug is in the drain position.

4. Slowly remove one of the side plugs to vent and aid in draining oil into a suitable container.

1

3

4

BD05H010 BD05H005

1. CHECK/FILL AND DRAIN PLUG

2. Use a 5 mm Allen wrench and open the check/fill and drain plug.

Oil should just be flowing out of the orifice.

4. CHECK/FILL AND DRAIN PLUG IN THE FILL AND CHECK POSITION

5. After the oil has drained, move the machine to place the check/fill and drain plug into the above position.

6. Fill with oil until it just begins running out of the hole.

7. Install the plugs and repeat the procedure for the other side.

131

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

TRIM THIS EDGE

IMPORTANT: If operating in muddy conditions for 20 hours or more, the oil change interval should be shortened by 50 per cent.

LUBRICATION

EVERY 250 HOURS Lubricate The Attachment Coupler Latch Handle

Checking The Drive Chain Tension

Specification.......molydisulfide grease

Check the tension of the four drive chains after the first 250 hours of operation on a new machine or if new chains have been installed.

1. Lower the loader lift arms to the ground. Turn the key switch to OFF and stop the engine.

1

2. Use a jack or hoist and lift the machine. Install blocks under the machine.

TRIM THIS EDGE

BD04M014

1. ATTACHMENT COUPLER LATCH HANDLE GREASE FITTING (1 EACH SIDE)

Grease the attachment coupler latch handles.

Lubricate The Attachment Coupler Latch Wedge Specification.......molydisulfide grease

BS04H104X

3. Rotate each tire and check for allowable movement of 0 to 1/4 inch (0 to 6 mm).

1

4. If the chains need adjustment see page 156.

1

BP97D017

1. ATTACHMENT COUPLER LATCH WEDGE GREASE FITTING (1 EACH SIDE)

Grease the attachment coupler latch wedges.

132

TRIM THIS EDGE LEFT PAGE Bur 87364592na

LUBRICATION

EVERY 250 HOURS Check The Battery Fluid Level And Clean The Terminals WARNING: Before you service a battery, always wear face protection, protective gloves and protective clothing. Battery acid or battery explosion can cause serious injuries.

SA046

WARNING: Battery acid causes severe burns. Batteries contain sulfuric acid. Avoid contact with skin, eyes or clothing. Antidote - EXTERNAL: flush with water. INTERNAL: drink large quantities of water or milk. Seek medical attention immediately. EYES: flush with water for 15 minutes and get prompt medical attention. BATTERIES PRODUCE EXPLOSIVE GASES. Keep sparks, flame, cigars and cigarettes away. Ventilate when charging or using in enclosed area. Always wear eye protection when working near batteries. Wash hands after handling. KEEP OUT OF REACH OF CHILDREN. WARNING: Sparks or flame can cause hydrogen gas in a battery to explode. To prevent an explosion, do the following: 1.When you disconnect the battery cables, always disconnect the negative (-) battery cable first.

2.When you connect the battery cables, always connect the negative (-) cable last.

3.Do not short circuit the battery posts with metal items.

4.Do not weld, grind, or smoke near a battery.

SB034

WARNING: When the battery electrolyte is frozen, the battery can explode if, (1) you try to charge the battery, or (2) you try to jump start and run the engine. To prevent the battery electrolyte from freezing, try to keep the battery at full charge. If you do not follow these instructions, you or others in the area can be injured.

SA033

WARNING: Before working on any part of the electrical system, disconnect the battery ground cable. Do not connect cable until all electrical work has been completed. This will prevent shorts or electrical shocks.

M198A

WARNING: DO NOT weld on this machine. (See your dealer for repairs).

Danger of explosion exists which can result in injury or death.

M478

133

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

TRIM THIS EDGE

M144B

LUBRICATION

EVERY 250 HOURS Specification..................distilled water

2

If the fluid level is low, add distilled water to each cell until the fluid level is at the split ring at the bottom of each cell opening.

IMPORTANT: If the temperature is 32° F (0° C) or below and you have added water to the battery, do the following: Connect a battery charger to the battery or run the engine for approximately two hours.

This procedure is necessary to mix the water with the electrolyte.

BD04C043

2. BATTERY FILL (ONE OF SIX)

Cleaning The Battery

Remove the floor plate.

TRIM THIS EDGE

Check the battery every 250 hours for dirt, corrosion and damage. Dirt, mixed with electrolyte or moisture on the top of the battery, can cause a discharged condition in the battery. Use one of the following methods to clean the battery.

1

1. Use Case Battery Saver, part n u m b e r M 2 0 3 7 6 . Fo l l o w t h e instructions on the container. This cleaner does not need water.

BD01C130

1. BATTERY

Clean the battery and surrounding area to reduce the risk of contamination before removing the battery caps.

2. Use baking soda or ammonia and flush the outside of the battery with water. If you do not have Case Battery Saver, use other special cleaners to prevent corrosion on the battery terminals.

3. Spray the battery terminals with battery terminal protector. Do not use grease.

134

TRIM THIS EDGE LEFT PAGE Bur 87364592na

LUBRICATION

EVERY 250 HOURS Radiator Coolant Level Specification.50% ethylene glycol and 50% water

Drain Water From The Fuel Filter Drain the water from the fuel filter after every 250 hours of operation.

WARNING: Hot coolant can spray out if radiator cap is removed. To remove radiator cap: Let system cool, turn to first notch, then wait until all pressure is released.

Scalding can result from fast removal of radiator cap.

Check and service engine cooling system according to maintenance instructions.

BD04B078

SA023

Every 250 hours check the radiator c o o l a n t l eve l w h e n t h e e n g i n e i s stopped and the coolant is cold.

1. FUEL FILTER DRAIN VALVE

Turn the drain valve on the fuel filter counterclockwise 2 or 3 turns and drain the water from the fuel filter.

1

BD04B097

1. RADIATOR CAP

Open the rear doors and remove the radiator cap. The coolant level must be up to the radiator cap opening.

NOTE: Only add the correct mixture of 50% ethylene glycol and 50% water to the radiator.

135

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

TRIM THIS EDGE

1

LUBRICATION

EVERY 250 HOURS Clean the Spark Arresting Muffler (If Equipped)

Check Chain Tank Oil Level

This procedure should be performed ever y 250 hours of operation and requires two people.

Check the level of oil in the chain tanks every 250 hours of operation.

Specification.. SAE 10W 30 engine oil 1. Park on firm, level ground.

1. Stop the engine.

2. See the procedure on page 100 and tilt the ROPS forward to access the engine compartment.

3. Remove the plug from the bottom of the muffler.

4. Apply the parking brake and disconnect the wire to the injection pump solenoid on the engine.

TRIM THIS EDGE

5. Be sure to wear face protection for this step. Have another person hold a block of wood over the muffler outlet.

6. Turn the key switch to START for approximately 30 seconds.

BK98E107X

1. OIL LEVEL PLUG

2. Remove the oil level plug.

Oil should be within 1/8 inch of the bottom threads in the plug hole.

7. Turn the key switch to OFF. 8. Connect the wire to the injection pump solenoid and install the plug in the muffler.

3. Add oil if required and repeat the procedure for the other side.

9. Return the ROPS to the operating position.

136

TRIM THIS EDGE LEFT PAGE Bur 87364592na

LUBRICATION

EVERY 250 HOURS Final Drive Fluid Check Check the fluid in each final drive motors every 250 hours of operation.

Specification.. Case 135H EP 80W-90 or 85W-140

BD05H005

1. CHECK/FILL AND DRAIN PLUG IN THE CHECK POSITION

Park the machine on firm, level ground with the side to be checked in the position shown above.

Remove the check/fill plug slowly. Oil should be just running out of the hole.

Add oil if necessary and replace the plug.

Repeat the procedure for the other side.

137

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

TRIM THIS EDGE

1

LUBRICATION

EVERY 500 HOURS Change The Engine Oil And Filter

6. Use a clean cloth and wipe the sealing surface of the oil filter base to remove all dirt.

Oil capacity with filter ..... 12 L (12.7 qt.)

Specification.......... Case No.1 15W40

7. Apply a thin layer of clean grease or oil to the gasket of the new filter.

NOTE: For more complete removal of foreign material, change the engine oil while the engine is still warm, not hot from operation.

Change the engine oil more frequently when the engine operating conditions are severe (frequent stopping and star ting and high or low engine temperatures).

1. Before draining the oil, have a suitable container ready.

8. Turn the new oil filter clockwise onto the base until the gasket m a ke s c o n t a c t w i th th e b a s e.

Continue to tighten the filter with your hand until tight.

IMPORTANT: DO NOT use a filter strap wrench to install the oil filter. An oil filter strap wrench can cause a leak if the filter is dented or overstressed.

TRIM THIS EDGE

9. Install the drain plug. Tighten to a torque of 50 to 60 pound-feet (68 to 82 Nm).

10. Add the engine oil.

11. Start the engine and run at low idle speed. Check the engine oil filter and drain plug for leaks. After two minutes, stop the engine, wait for 2 or 3 minutes, and check the engine oil level again.

1

BD04M039

1. ENGINE OIL DRAIN PLUG ACCESS COVER

2. Remove the engine oil drain plug access cover.

3. Put a suitable container under the drain plug. Remove the engine oil drain plug.

12. Install the engine oil drain plug access cover.

13. Dispose of the oil in accordance with the local regulations. DO NOT drain onto the ground or into a d r a i n . B e r e s p o n s i bl e fo r t h e environment.

4. To remove the engine oil filter, tilt the operators compar tment forward, see page 110.

5. Turn the filter counterclockwise to r e m o ve . D i s p o s e o f t h e f i l t e r properly.

138

TRIM THIS EDGE LEFT PAGE Bur 87364592na

LUBRICATION

Every 500 Hours Replace the Fuel Filters Replace the in-line and primary fuel filter every 500 hours or operation or if the engine is hard to star t or lacks power.

3

2

This operation is easier to accomplish with the loader arms in the raised and secured position. Also, remove the primary filter first for easier access to the in-line filter.

3

1

A_FIL_QW

2

5. Depress the button on the sides of the connectors on both sides of the in-line filter (2) and remove the filter.

6. Install the new in-line fuel filter.

Make sure the arrow on the filter is p oin tin g towa rd th e f ue l ha nd primer.

BD04B082

1. PRIMARY FUEL FILTER 2. IN-LINE FUEL FILTER

7. Apply clean engine oil to the new rubber seal.

1. Clean the area around both filters before proceeding.

8. Install the rubber seal on the primary filter head stud.

2. Use a strap wrench and turn the primary filter (1) counterclockwise to remove.

3. Remove the rubber seal from the stud on the filter head.

4. Use a cloth and clean the gasket surfaces of the filter body.

9. Apply clean oil to the gasket of the new filter. Do not fill the new filter with fuel before installation.

10. Turn the filter clockwise onto the filter body until the filter gasket makes contact with the filter body.

Continue to tighten the filter with your hand for 1/2 to 3/4 turn.

IMPORTANT: Do not use a strap wrench to tighten the filter.

11. Fill the fuel tank.

139

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

TRIM THIS EDGE

3. QUICK CONNECTORS

LUBRICATION

3

BD04C112

4. AIR REMOVAL SCREW

12. Loosen the air removal screw on the top of the fuel filter head.

TRIM THIS EDGE

13. Actuate the hand primer plunger up and down. When fuel comes out free of air, tighten the air removal screw.

14. Start the engine and check for fuel leaks around the fuel filter.

140

TRIM THIS EDGE LEFT PAGE Bur 87364592na

LUBRICATION

EVERY 500 HOURS The Fan Belt should be checked for proper tension and wear or damage every 500 hours.

Check the belt using the deflection method 1/4 inch at mid span. Check mid-span between alternator and fan pulleys.

Used belt ......................... 23 + or - 1 lbf New belt .......................... 26 + or - 1 lbf

Hydraulic Oil Filter Replacement The Hydraulic Oil Filter should be replaced ever y 500 hours or if the warning lamp illuminates.

This procedure is easier to accomplish with the loader arms in the raised and secured position.

WARNING: BURN HAZARD: Do not service the hydraulic system until the temperature of the oil is below 49° C (120° F).

Inspect The Rops Your machine has a roll-over protective structure (ROPS) which is also certified for falling object protection structure (FOPS). A ROPS/FOPS label is fastened to the structure. The label shows the serial number of the ROPS/ FOPS, gross weight, approval, regulation, and model numbers of the machine.

C h e c k t h e o p e r a t o r ’s s e a t a n d m o u n t i n g p a r t s fo r t h e s e a t b e l t .

Tighten the bolts to 38 -45 pound-feet (52-61 Nm).

Check for cracks, rust, or holes in the ROPS and ROPS par ts. Age, environment, working conditions and accidents can cause damage. If you h ave a ny d o u b t a b o u t t h e RO P S system contact your Dealer.

M477

1. Clean the area around the filler cap and hydraulic filter with cleaning solvent.

2. Turn the filler cap 1/2 turn to relieve the pressure in the reservoir. Do not remove the filler cap.

3. To remove the filters, turn counterclockwise. Dispose of the filter properly.

4. Apply a thin layer of clean grease or oil on the O-ring of the new filter.

5. Install the filter. Hand tighten the filter 2/3 turn after the filter O-ring touches the filter head.

141

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

TRIM THIS EDGE

Fan Belt Tension

LUBRICATION

EVERY 500 HOURS Check and Adjust the Mechanical Attachment Coupler Wedge Adjustment 1. Move the hand lever to the point where the hand lever goes through the over center position. With the hand lever in this position the spring should be fully compressed.

1

If the spring is not full compressed:

2

A. Remove the attachment.

3

B. Remove the nut and disassemble the yoke rod from the trunnion.

TRIM THIS EDGE

C. Add washers between trunnion and the spring.

4

the

5

D. Assemble the yoke rod and trunnion and replace the nut.

E. Mount the attachment and move the hand lever to the over center position and inspect the spring.

NOTE: If the hand lever will not move through the over center position, remove washers so that the over center position can be achieved.

256L93

1.

2.

3.

4.

5.

NUT TRUNNION WASHERS SPRING YOKE ROD

142

TRIM THIS EDGE LEFT PAGE Bur 87364592na

LUBRICATION

EVERY 500 HOURS Coupler Attachment Fit-Up 1. Mount the attachment to the coupler and engage the locking wedges.

2. Raise the attachment enough to a l l ow m e a s u r i ng t h e d i s ta n c e between the bottom of the coupler and the lower angle bracket of the attachment.

IMPORTANT: Block the loader arms while the attachment is raised.

TRIM THIS EDGE

3. If the measurement is greater than . 3 7 5 i n c h ( 9 . 5 m m ) , s e e yo u r Dealer.

1 9.5 mm (.375 inch)

2 257L93

1. ATTACHMENT 2. COUPLER

143

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

LUBRICATION

EVERY 500 HOURS Final Drive Oil Change Drain and replace the oil in the final d r i ve m o t o r s eve r y 5 0 0 h o u r s o f operation or once a year.

Specification.. Case 135H EP 80W-90 or 85W-140 Capacity ...................... 0.55 L (0.58 qt.)

4. Position the machine to place the check/fill and drain plug into the position shown below.

3

1. Place the machine on firm, level ground with the final drive to be drained in the position shown below.

BD05H010

3. CHECK/FILL AND DRAIN PLUG IN THE CHECK/FILL POSITION

2 TRIM THIS EDGE

5. Fill with oil until it begins running out of the hole.

1

6. Install the plugs and repeat the procedure for the other side.

BD05H004

1. CHECK/FILL AND DRAIN PLUG IN THE DRAIN POSITION 2. CENTER PLUG

2. Slowly remove the drain plug and drain the oil into a suitable container.

3. Slowly remove the center plug to vent and aid in draining.

144

TRIM THIS EDGE LEFT PAGE Bur 87364592na

LUBRICATION

EVERY 1000 HOURS Drain Water and Sediment from the Fuel Tank 1

BD04F073

1. Place the machine on a firm, level surface.

2. Clean the area around the drain plug.

3. Loosen the plug at the bottom of the fuel tank, located under the right rear side of the machine.

Turn the plug slowly counterclockwise until water starts to drain.

Once fuel begins to drain tighten the plug.

145

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

TRIM THIS EDGE

1. FUEL TANK DRAIN PLUG

LUBRICATION

Every 1000 Hours Change Hydraulic Reservoir Oil Specification...SAE 10W 30 engine oil

2. Clean the filler cap and the area around the cap to reduce the risk of contamination.

3. Slowly turn the filler cap 1/2 turn to relieve pressure in the reservoir.

D o n o t r e m o ve t h e c a p u n t i l pressure is relieved.

1

4. Clean the area around the drain plug.

5. Remove the plug and drain the oil into a suitable container.

6. Install the drain plug.

TRIM THIS EDGE

BD04M040

1. HYDRAULIC OIL RESERVOIR DRAIN PLUG

1. Place the machine on a firm, level surface.

7. Refill the reservoir and apply clean oil to the filler cap seal before installing.

8. Start the engine and run at low idle for approximately 2 minutes.

9. Stop the engine and check for leaks.

WARNING: Engine fuel is flammable and can cause a fire or explosion.

Do not fill the fuel tank or service the fuel system near and open flame, welding, burning cigars, cigarettes, etc.

SA022

WARNING: FIRE HAZARD: Do not smoke while filling the hydraulic reservoir. Do not fill near open flames.

M476

146

TRIM THIS EDGE LEFT PAGE Bur 87364592na

LUBRICATION

EVERY 1000 HOURS Check Engine Valve Clearances The valves should be checked for proper tolerance. See the Ser vice Manual for this machine or contact your Dealer.

5. Wearing proper safety gear remove the fill plug and clean each chain tank compar tment with an approved solvent.

NOTE: If chain adjustment is required at the same time as oil change, remove the inspection covers and flush and dry chain tank components.

Change the Chain Tank Oil

6. Install drain plugs.

The chain tank oil should be changed every 1000 hours of operation.

1. Park the machine on a firm level surface.

3 1

BK98E107X

2. DRIVE CHAIN TANK INSPECTION COVER (ONE EACH SIDE) 3. OIL LEVEL PLUG (ONE EACH SIDE)

7. Level the machine.

BD04F073

8. Remove oil level plugs. (2)

1. RIGHT SIDE CHAIN TANK DRAIN PLUG (ONE EACH SIDE)

9. Fill each chain tank with oil until it just begins to flow out of the oil level orifice.

2. Clean the area around the drain plugs and inspection covers.

3. Use a jack to raise the front of the machine to aid draining.

4. Remove the drain plug from each compartment.

10. Install the oil level plug.

NOTE: Use an approved sealant between the inspection cover and the chassis, if removed.

147

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

TRIM THIS EDGE

2

LUBRICATION

EVERY 1000 HOURS Cab Filter

Cleaning with compressed air:

The cab filter should be checked every 1000 hours of operation. Inspect, clean or replace the filter as necessary. In extreme wor k conditions the filter should be checked and cleaned more frequently.

●

You must wear face protection for this procedure.

●

You must not use more than 30 psi (2 bar) of compressed air.

●

You must not hold the nozzle closer than 1 inch (25 mm) from the filter.

A

1

1

TRIM THIS EDGE

A_CAB _FIL

1. CAB FILTER THUMBSCREWS

BS99K083

To access the cab filter remove the two thumbscrews.

2

A_FIL

2. CAB FILTER

R e m o ve a n d c h e c k t h e f i l t e r fo r damage, debris or dirt.

148

TRIM THIS EDGE LEFT PAGE Bur 87364592na

LUBRICATION

EVERY 2000 HOURS Change Engine Coolant

5. Place a hose (1) on the radiator drain and loosen the drain valve.

Drain, flush, and refill the engine coolant every 2000 hours of operation or each year, whichever occurs first.

WARNING: Hot coolant can spray out if the radiator cap is removed. To remove the radiator cap: Let the system cool, turn the cap counterclockwise to the first notch, then wait until all pressure is released.

Scalding can result from fast removal of radiator cap.

Check and service the engine cooling system according to maintenance instructions.

6. After the coolant is removed, tighten the radiator drain valve and remove the hose.

7. Add cleaning solution to the cooling system and fill the cooling system w i t h c l e a n w a t e r. Fo l l o w t h e directions included with the cleaning solution.

8. After you drain the cleaning solution, flush with clean water.

10. Make sure that the outside of the engine and radiator is clean.

SA023

1. Place the machine on firm, level ground and block the rear tires.

2. Raise the front of the machine and place 6 inch blocks under the front tires.

3. After the system is cool, remove the radiator cap.

4. Release the top radiator latch and pull the bottom of the radiator rearward into the detents.

1

11. Remove the blocks from under the front tires and lower the machine to the ground.

12. Fill the cooling system until the coolant level is up to the top of the radiator cap opening and install the radiator cap.

13. Fill the coolant reservoir up to the FULL mark on the reservoir.

14. Start the engine and increase the temperature of the engine coolant.

When the coolant is at operating temperature, stop the engine and allow to cool. Check the coolant level at the coolant reservoir only.

Do not remove the radiator cap.

15. Dispose of drained coolant responsibly. Do not pour on ground or down drain.

BD05H086

149

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

TRIM THIS EDGE

9. Check the hoses, elbows and water pump for leaks.

LUBRICATION

EVERY 2000 HOURS 2

Engine Air Filters Replace the air filter elements every 2000 hours of operation or: ●

If the Air Filter Restriction Indicator Lamp illuminates.

●

The filters have been in the machine for one year.

BD04M031

2. FILTER COVER LATCHES

2. Pull the filter cover latches up to release the cover. The cover is hinged on the bottom.

TRIM THIS EDGE

3. Clean the inside of the filter cover and the dust valve.

1

4

BD04F074

1. ENGINE AIR FILTER WARNING LAMP

IMPORTANT: It is recommended to NOT remove the filter elements to check for restriction.

If the air filter lamp illuminates when the engine is running you must service the air filter elements.

BD04M033

3. PRIMARY FILTER

4. Remove the primary filter.

1. Place the machine on firm, level ground with the lift arms down on the ground.

150

TRIM THIS EDGE LEFT PAGE Bur 87364592na

LUBRICATION

5

6 BD04M033

6. HINGE TABS

BD04M035

4. SECONDARY FILTER

6

IMPORTANT: When installing the filters make sure the seals are making proper contact.

BD04M036

5. AIR FILTER HOUSING

6. Clean the filter housing before installing the new filters.

7. Install a new secondary filter.

8. Install a new primary filter.

151

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

TRIM THIS EDGE

9. Install the filter cover and secure the latch. Be sure to get the hinge tabs into the slots on the filter housing.

5. Remove the secondary filter. There are finger holds on the filter.

LUBRICATION

NOTES

TRIM THIS EDGE 152

TRIM THIS EDGE LEFT PAGE Bur 87364592na

ADJUSTMENT/MAINTENANCE STEEL TRACK ADJUSTMENTS (IF EQUIPPED) Checking The Track Sag

1. Check the existing track tension by measuring the track sag.

A. Place a straight edge between the tires resting on the highest point above each tire.

1

2

Track Length Adjustment Use the following chart to determine the proper track length adjustment based on the length that needs to be removed or added.

IMPORTANT: Always wear face protection when adjusting the track length.

ADJUSTMENT CHART

BI97C129

1. STRAIGHT EDGE 2. 25 MM (1 IN) MINIMUM SAG

B. Measure the distance between the lower side straight edge and t h e t o p o f t h e t r a ck p a d t o determine the amount of track sag. The minimum amount of track sag is (1 inch) 25 mm .

Allowable sag is up to 3 inch (75 mm).

Move 1 Hole

=

20.6 mm (.81 in)

Move 2 Hole

=

41.2 mm (1.62 in)

Move 3 Hole

=

61.7 mm (2.43 in)

Move 4 Hole

=

82.6 mm (3.25 in)

Move 5 Hole

=

103.1 mm (4.06 in)

Move 6 Hole

=

123.7 mm (4.87 in)

Move 7 Hole

=

144.3 mm (5.68 in)

Move 8 Hole

=

165.1 mm (6.50 in)

Move 9 Hole

=

185.7 mm (7.31 in)

Move 10 Hole

=

206.2 mm (8.12 in)

Move 11 Hole

=

2266.8 mm (8.93 in)

Move 12 Hole

=

247.7 mm (9.75 in)

1. Center the binder or come-along between the tires.

1

NOTE: Operating with the tracks too tight could result in damage to the tires, track or loader.

NOTE: Always maintain the correct tire pressure when tracks are being used.

BI97C128

1. BINDER

153

TRIM THIS EDGE RIGHT PAGE (Section First Page) Bur 87364592na

TRIM THIS EDGE

If the tracks become loose or are too tight, adjustment is required. Use the following procedure to maintain the proper track tension.

C. If the tracks are too tight or too loose adjustment will be necessary. See “Track Length Adjustment”.

ADJUSTMENT/MAINTENANCE 2. Tighten the binder or come-along to relieve the tension in the area where the track link adjustment is to be made.

1

2

3. Remove the track link bolt.

4. If the track needs to be shortened move the link to the outer holes.

BI97C129

1. STRAIGHT EDGE 2. TAKE TRACK SAG MEASUREMENT HERE

1

8. If the track sag is still not correct r ep e a t s te p s 1 th r ou g h 7 i n a different location.

2 TRIM THIS EDGE

9. Repeat the procedure on opposite side of the machine.

BI97C127

1. LENGTHENS TRACK 2. SHORTENS TRACK

10.

5. If the track requires lengthening use the inner holes.

6. Install the track link bolt and tighten to 70 to 84 pound-feet (95 to 114 Nm).

7. Remove the binder or come-along and remeasure the track sag.

154

TRIM THIS EDGE LEFT PAGE Bur 87364592na

the

ADJUSTMENT/MAINTENANCE

ADJUSTING THE HAND THROTTLE If the hand throttle lever becomes loose or is too stiff, adjustment will be required.

Adjust the hand throttle lever using the following procedure.

1 3 2 BD04G023

3. ADJUSTMENT BOLT

1. Loosen the set screw at the rear and toward the gas strut side of the pivot.

2. Adjust the pivot bolt by either tightening or loosening. This will apply pressure or relieve pressure on the friction disc.

3. Tighten the set screw.

155

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

TRIM THIS EDGE

BD04G023

1. SET SCREW 2. GAS STRUT MOUNT

ADJUSTMENT/MAINTENANCE

ADJUSTING THE DRIVE CHAIN TENSION 1. Lower the bucket or attachment to the ground and stop the engine.

2. Use a jack or hoist and lift the machine. Install blocks under the machine as shown. Raise loader lift arms and engage support strut. Remove the wheels.

3. Clean the area around each axle housing.

1

1 TRIM THIS EDGE

BD01C274X

1. AXLE HOUSING

BD01C265X

BD01C267X

4. Loosen the axle housing mounting nuts so the axle is free to move forward or rearward.

5. Wear eye protection and tap the axle housing with a brass hammer until it stops moving.

6. Tighten two nuts to hold the axle housing in place. 5 pound- feet (7 Nm)

156

TRIM THIS EDGE LEFT PAGE Bur 87364592na

ADJUSTMENT/MAINTENANCE 12. Tighten the axle housing mounting bolts to a torque of 165 to 190 pound-feet (223 to 265 Nm).

13. Install the four wheels.

If the machine is equipped with stamped center wheels, the lug nuts will be tapered type lug nuts.Tighten each lug nut to a torque of 100 to 120 pound-feet (135 to 163 Nm).

BD01C267X

7. Reinstall the wheel with two lugnuts, and recheck the chain deflection. Deflection should be 0 to 1/4 in (0 to 6 mm).

If the machine is equipped with solid center wheels, the lug nuts will be flange type lug nuts.Tighten each lug nut to a torque of 165 to 195 pound-feet (224 to 265 Nm).

TRIM THIS EDGE

8. Repeat the above steps for the remaining drive chains.

9. Following adjustment of all drive chains, start the engine and run at low idle.

10. Move the control levers all the way forward for five seconds. Stop the engine.

11. If required, tighten or loosen the drive chains to get the correct deflection.

BD01C268

14. Remove the blocks or stands and lower the machine to the floor.

NOTE: If axle housings are at extreme outward positions and chain adjustment is not correct, the drive chains and axle sprockets must be replaced.

157

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

ADJUSTMENT/MAINTENANCE

MAINTENANCE OF THE SEAT BELT 1. Check the seat belt for damage each time it is used. Replace all parts that are damaged.

2. Make sure that the mounting bolts of the seat belt are tight after every 500 hours of operation.

3. Keep the seat belt clean. Use only soap and water to wash the seat belt. Dye or other compounds can cause damage to the seat belt.

Torque Specifications For Seat Belt

1

1

TRIM THIS EDGE

1. TIGHTEN TO 38 TO 45 POUND-FEET (52 TO 61 NM)

RIDE CONTROL ACCUMULATOR If the ride control accumulator must be replaced for any reason, it must be done by your Dealer.

158

TRIM THIS EDGE LEFT PAGE Bur 87364592na

BD04M004 / BD04M005

ADJUSTMENT/MAINTENANCE

ROLL-OVER PROTECTION STRUCTURE Your machine has a roll-over protective structure (ROPS) which is also certified for falling object protection structure (FOPS). A ROPS/FOPS label is fastened to the structure. The label shows the serial number of the ROPS/FOPS, gross weight, approval, regulation, and model numbers of the machine.

BD04M050

Seat Belt The seat belt is an important part of your ROPS. You must wear the seat belt at all times when you operate the machine.

Before you operate this machine, always make sure that the ROPS and Operators seat belts are correctly installed. See “Seat Belt Maintenance” on page 158.

Maintenance and Inspection of ROPS After the first 20 hours of operation and after every 500 hours of operation, do the following: 1. Check the operators seat and the mounting parts for the seat belt. Tighten the bolts to the correct torque. See page 158. Replace parts that have wear or damage.

2. Check for cracks, rust, or holes in the ROPS and ROPS parts. Age, weather, and accidents can cause damage to the ROPS and ROPS parts. If you have any doubt about the ROPS system, see your Case dealer.

159

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

TRIM THIS EDGE

ROPS Label

ADJUSTMENT/MAINTENANCE

Damage to the ROPS If the machine has rolled over or the ROPS has been in some other type of accident (such as hitting an overhead object during transport), you must replace the damaged ROPS components to maintain as much protection as you had originally.

After an accident, check the following for damage: A. ROPS canopy and side screens.

B. Operators seat.

C. Seat belt mounting bolts and seat belt.

Before you operate the machine, replace all ROPS components that are damaged.

See the parts catalog or your Case dealer for components that are replaceable.

DO NOT TRY TO WELD OR STRAIGHTEN THE ROPS.

TRIM THIS EDGE

WARNING: Do not modify ROPS in any manner. Unauthorized modifications such as welding, drilling, cutting or adding attachments can weaken the structure and reduce your protection. Replace ROPS if subjected to roll-over or damage. Do not attempt to repair.

SB026

WARNING: If you operate this machine without a ROPS and the machine rolls over, you can be injured or killed. Remove the ROPS only for service or replacement. Do not operate this machine with the ROPS removed.

SA027

WARNING: Adding additional weight (attachments, etc.) to the machine can cause injury or death. Do not exceed the gross weight printed on the ROPS label.

SA028

WARNING: ALWAYS fasten the seat belt and pull the seat bar down before you start the engine. Make sure the buckle for the seat belt is fastened correctly.

SB030

160

TRIM THIS EDGE LEFT PAGE Bur 87364592na

ADJUSTMENT/MAINTENANCE

FIRE EXTINGUISHER Type of Fire Extinguisher

Inspection and Care

It is recommended that you have a fire extinguisher on your machine. This fire extinguisher shown below is available from your Case dealer and can be installed on the machine.

EVERY MONTH: It is recommended that you inspect the fire extinguisher once each month for damage and to i n s u r e t h a t t h e g a u g e i s wo r k i n g correctly.

ONCE EACH YEAR: Have the fire equipment representative inspect the fire extinguisher.

ONCE EVERY 12 YEARS: Have the fire equipment representative hy d r o s t a t i c a l l y t e s t y o u r f i r e extinguisher.

B9409008

This dry chemical fire extinguisher has a 5 pound capacity and is approved for class A, B, and C type fires. The operating temperature is from -65° to 120° F (-54° to 49° C).

PLASTIC AND RESIN PARTS Avoid using gasoline, paint thinner, etc., when cleaning the windows, consoles, or any plastic or resin parts. Use only water, mild soap, and a soft cloth when you clean these parts.

Using gasoline, thinners, etc., can cause discoloration, cracking, or deformation of the part being cleaned.

161

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

TRIM THIS EDGE

ONCE EVERY 6 YEARS: Have the dry chemical removed and refilled by a fire equipment representative.

ADJUSTMENT/MAINTENANCE

REMOVAL OF SLIDING SIDE WINDOWS (IF EQUIPPED) The sliding side windows may be removed for cleaning or replacement using the following procedure 1. Enter the operators compartment and slide the glass to the closed position.

2. Locate the slot on the top track near the rear end. Use a flat blade screwdriver to pry the inner track out and remove. Slide window back and lift bottom out of track.

Installing the Sliding Side Windows.

TRIM THIS EDGE

1. Lift up on the front of the glass while guiding it into the top channel. Slide the loose end of the flocked rubber still remaining on the glass into the channel and under the glass. If necessary, coat the end of the flocked rubber with soapy water. This will aid in sliding the flocked rubber into position.

Smooth out the flocked rubber and make sure the entire length is pressed into the channel.

2. Slide the glass to the closed position and install the rear piece of the flocked rubber in the same manner. Make sure both pieces of flocked rubber fit together end to end under the glass.

162

TRIM THIS EDGE LEFT PAGE Bur 87364592na

ELECTRICAL SYSTEM ALTERNATOR CHARGING SYSTEM Follow these general rules to prevent damage to the electrical system.

WARNING: Sparks or flame can cause hydrogen gas in a battery to explode. To prevent an explosion, do the following: 1.When you disconnect the battery cables, always disconnect the negative (-) battery cable first.

2.When you connect the battery cables, always connect the negative (-) battery cable last.

3.Do not short circuit the battery posts with metal items.

4.Do not weld, grind or smoke near a battery.

84-109

2. When you use an auxiliary battery for starting, connect negative to negative and positive to positive.

3. DO NOT use a battery charging machine to start the machine.

4. Never operate the machine when the battery cables are disconnected.

5. When you do maintenance on the engine, prevent foreign material from entering the alternator.

163

TRIM THIS EDGE RIGHT PAGE (Section First Page) Bur 87364592na

TRIM THIS EDGE

1. DO NOT make a reverse battery connection.

ELECTRICAL

WORK LAMPS Front 1. To replace a bulb, shift the work lamp to one side depressing the spring retainer and lift the opposite side of the work lamp out of the ROPS frame.

BP96N049

4. Use tissue paper to hold the new bulb while installing it into the bulb socket. Grease and oil from your skin will shorten the bulb life.

TRIM THIS EDGE

5. Install the bulb socket in the back of the lamp assembly.

BP96N050

2. Rotate the electrical connector and bulb socket on the back of the lamp assembly 1/4 turn.

6. Install the lamp assembly into the RO P S f r a m e by i n s e r t i n g t h e SPRING CLAMP SIDE FIRST and depressing the spring. The other side will then slide into the ROPS frame.

Rear

BP96N048

3. Remove the bulb from the bulb socket and discard.

BD01C121

To replace the rear work lamp, open the rear access door and rotate the bulb socket assembly 1/4 turn. Remove the bulb from the socket. Install new bulb.

164

TRIM THIS EDGE LEFT PAGE Bur 87364592na

ELECTRICAL

TAIL LAMPS To replace the tail lamps:

BD01C125

4. Install the lens cover.

5. Connect the wire harness to the terminals on the back of the tail lamp assembly.

6. Install the tail lamp assembly in the door with the two screws.

BD01C124

2. Disconnect the wiring harness from the terminals on the back of the tail lamp assembly.

165

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

TRIM THIS EDGE

BD01C123

1. Remove the two screws which secure the lens cover to the tail lamp assembly.

3. Remove the lens cover. Remove the bulb and discard.

ELECTRICAL

Accessory Power Outlet (If Equipped)

Fuses And Relays

The accessor y power outlet (if equipped) is located on the lower left side of the operators compartment side panel. The accessory power outlet can provide power for operator convenience items.

The fuses protect the electrical circuits.

Switch off the power to a circuit before replacing a fuse. Make sure you install a f u s e o f t h e c o r r e c t va l u e w h e n replacing a fuse.

1

TRIM THIS EDGE

BD04C044

1. ACCESSORY POWER OUTLET (IF EQUIPPED)

012

The fuses and relays are located on the left side of the operator in the panel between the seat and the side of the ROPS. The fuse decal is located on the back of the cover. See the following page for a deatil.

166

TRIM THIS EDGE LEFT PAGE Bur 87364592na

ELECTRICAL

2

3

5

4

7

6

10

14

11

15

12

16

13

7

9

8

XXXXXX

FUSE LOCATION

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

11.

12.

13.

14.

15.

16.

17.

AMPS

Starter Relay System Power / Relay - Fuse Block 1 Interlock System Relay Std. Hyd. Aux Interlock / No Crank Relay Std. Hyd. Aux Interlock / Fuel Shutoff Relay System Power (Accessory) Relay - If Equipped Fuse Block 2 Work / Road Light Relay # 1 Work / Road Light Relay # 2 Flasher Relay Light Fuse Wiper Fuse Interlock System Fuse Horn / Backup Alarm Fuse Accessory Power Socket Fuse Fan Blower / Conditioner Hazard Lights / High Flow Hyd. Auxiliary Controls / Rotating Beacon

167

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

45 45 45 45 45

45 20 25 15 10 15 20 10 10

TRIM THIS EDGE

1

ELECTRICAL

NOTES

TRIM THIS EDGE 168

TRIM THIS EDGE LEFT PAGE Bur 87364592na

MACHINE STORAGE WARNING: Batteries produce explosive gases. Keep sparks, flame, and cigarettes away. Ventilate when charging or using in an enclosed space.

Always shield eyes when working near batteries.

SA031

WARNING: Before you service a battery, always wear face protection, protective gloves and protective clothing. Battery acid or battery explosion can cause serious injuries.

SA046

STORAGE PREPARATION

1. Prior to storing, wash the machine.

2. Lubricate the machine at all grease fittings.

3. Paint any areas where the paint has been damaged.

4. Move all hydraulic controls to relieve any pres sure in the hydraulic circuits.

5. Drain the fuel tank.

6. Put approximately 8 litres (2.1 gallons) of diesel flushing oil in the fuel tank. Run the engine until the exhaust smoke is blue-white.

12. Cover the exposed cylinder rods, and valve spools and any other bare metal parts with Case Rust and Corrosion Preventive (Par t Number B17510).

13. Charge the battery. Remove the battery from the machine and put the battery on a wooden pallet in a cool dry area. If possible, keep the batter y in a building where the temperature is above freezing 0° C (32° F). Make sure the battery is clean.

14. Cover the exhaust outlet.

7. Drain the flushing oil from the fuel tank.

15. Do periodical checks for protection.

Look for corrosion.

8. Put 15 ml (5 oz or one teaspoon) of Shell Oil Company VPI crystals in the fuel tank.

NOTE: Check the battery periodically for the correct electrolyte level. Test the electrolyte with a hydrometer. When the hydrometer reading is near 1.215, charge the battery.

9. Change the engine oil and replace the oil filter.

10. Drain the cooling system. Leave the drain valves open and do not tighten the radiator cap. Put a Do Not Operate tag in the cab.

Chain Compartments

11. Clean or replace the air cleaner elements.

1. Drain and flush compartments.

both

chain

2. Put new oil compartment.

each

chain

169

TRIM THIS EDGE RIGHT PAGE (Section First Page) Bur 87364592na

into

TRIM THIS EDGE

If the machine is to be in storage for more than 90 days, park the machine inside a building. If a building is not available, park the machine in a dry area on planks and cover the machine with a waterproof covering.

MACHINE STORAGE

STORAGE REMOVAL 1. Fill the fuel tank.

2. Tighten the cooling system drain valves.

10. Prime the turbocharger oil lines w i t h o i l u s i n g t h e fo l l o w i n g procedure: A. Disconnect the electrical connector to the injection pump solenoid. This will prevent the engine from starting.

3. Put coolant into the engine cooling system.

4. Check the engine oil level.

5. Check the condition of the engine fan belt and replace it if required.

B. Make sure all persons are clear of the machine. Turn the key switch to START and actuate the star ter for about 10 to 15 seconds.

6. Check the hydraulic fluid level.

TRIM THIS EDGE

7. Use a petroleum base solvent and remove the Case Rust and Corrosion Preventive from the hydraulic cylinder rods and spools, etc.

8. Install a fully charged battery.

9. Remove air from the engine fuel lines.

C. Reconnect the wire to injection pump solenoid.

the

IMPORTANT: Before starting the engine, make sure there are no leaks, missing or broken parts.

11. Start the engine and run at idle speed for 2 minutes. Check for leaks around the filters and drain plugs.

12. Stop the engine and check the fluid levels of the engine cooling system and drive chain compar tments.

See the Engine Cooling System and Drive Chain Compar tment sections for the correct procedure on checking the fluid levels.

170

TRIM THIS EDGE LEFT PAGE Bur 87364592na

SPECIFICATIONS 450 / 450CT / 465 ENGINE Make and model.............................................................................Case 445T/M2 Aspiration ..................................................................................................... Turbo Firing order .............................................................................................. 1- 3-4-2 Bore ......................................................................................... 104 mm (4.10 in) Stroke......................................................................................... 132 mm (5.20 in) Displacement ................................................................. 4.5 L (274 cubic inches) Compression ratio .......................................................................................... 17:5 Gross Bare Engine Power SAE net..................................................................61.0 kW (82 hp) @2300 rpm SAE gross .............................................................66.0 kW (89 hp) @ 2300 rpm High Idle, no load ........................................................................ 2480 ± 50 rpm Rated speed - full load ....................................................................... 2300 rpm Low Idle ...................................................................................... 1050 ± 50 rpm Peak torque........................................................357 Nm (263 lb ft) @ 1400 rpm Engine lubrication Pump..........deep sump with plate cooler and pressurized under-piston nozzles Pump operating angle ratings Side-to-side.............................................................................. rated 35 degrees Fore and aft.............................................................................. rated 35 degrees Oil filtration ...........................................................replaceable, full-flow cartridge NOTE: All specifications are given according to SAE standards or Recommended Practices where the specification applies.

171

TRIM THIS EDGE RIGHT PAGE (Section First Page) Bur 87364592na

TRIM THIS EDGE

Engine speeds

SPECIFICATIONS

ELECTRICAL SYSTEM Alternator ...................................................................................... 12 Volt, 95 Amp Battery (Standard)....................................................................... 12 Volt, 850 CCA Starter ............................................................................................. 12 Volt 2.7 kW Fuses Main Power Fuse Block Backup Alarm - Horn .............................................................................. 10 Amp LH Control .............................................................................................. 15 Amp Wiper ..................................................................................................... 25 Amp Lights ...................................................................................................... 20 Amp Accessory Power Fuse Block Hazard/Turn Signals/High Flow .............................................................. 10 Amp Hyd Coupler/Rotating Beacon ................................................................ 10 Amp Blower - AC............................................................................................. 20 Amp Front Aux Elec Control............................................................................ 15 Amp

TRIM THIS EDGE

Circuit Breakers Main Power Relay Feed ............................................................................ 40 Amp Accessory Power Relay Feed ................................................................... 40 Amp Key Switch Battery Feed........................................................................... 15 Amp Relays Starter .......................................................................................... 12 Volt, 45 Amp System Power for Fuse Block 1 ................................................... 12 Volt, 45 Amp System Power Accessory for Fuse Block 2 (If Equipped) ............ 12 Volt, 45 Amp Interlock System .......................................................................... 12 Volt, 45 Amp Fuel Pull In Coil............................................................................ 12 Volt, 45 Amp Front Work Lamps ..................................................................................... 50 Watt Rear Work Space Lamp ............................................................................. 50 Watt

172

TRIM THIS EDGE LEFT PAGE Bur 87364592na

SPECIFICATIONS

COOLING SYSTEM Radiator cap pressure............................................................ 89.6 kPa (13.0 psi) Thermostat ..................................................................................... 82° C (180° F) Opening range ...................................................... 83° to 95° C (181° to 203° F) Fully open ..................................................................................... 94° C (202° F)

HYDRAULIC SYSTEM Flow Rates Auxiliary Hydraulic Circuit ....................................................................... 23.3 gpm High Flow (combined) 450/465 ............................................................... 39.1 gpm

POWER TRAIN Drive Type ............................................................................................. Hydrostatic Drive Pump - Pilot ....................................................................................... Rexroth Type.......................................................................................Tandem Axial Piston Drive Motor.................................................................................................. Rexroth Type ................................................................................................. Radial Piston Final Drive (wheel units)........................................................... Sprocket and Chain Final Drive Chain Size (wheel units) .................................................... ASA 120HS Final Drive (track units) ................................................. Single-reduction planetary

BRAKES Brake Type ................................... SAHR (Spring Applied Hydraulically Released)

173

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

TRIM THIS EDGE

Drive Pump - Mechanical ................................................................ Sauer-Danfoss

SPECIFICATIONS

OPERATING WEIGHTS Basic Machine Operating Weight 450 ................................................................3909 kg (8620 lbs) Operating Weight 450CT .........................................................4951 kg (10915 lbs) Operating Weight 465 ................................................................4021 kg (8865 lbs) NOTE: 450 - 465 operating weight includes 12 x 16.5 tires, 1854 mm (73 in) dirt bucket, mechanical attachment coupler, 75 kg (165 pound) operator, full fuel and standard equipment.

NOTE: 450CT operating weight includes 450 mm (17.7 in) track, 2133 mm (84 in) dirt bucket, mechanical attachment coupler, 75 kg (165 pound) operator, full fuel and standard equipment.

SHIPING WEIGHTS (APPROXIMATE) Shipping Weight 450 .................................................................3567 kg (7865 lbs) Shipping Weight 450CT ...........................................................4582 kg (10102 lbs) TRIM THIS EDGE

Shipping Weight 465 ..................................................................3679 kg (8112 lbs) NOTE: Shipping weight includes 11.3 L (3 gal) fuel, no bucket and no operator.

ADDITIONAL WEIGHTS FOR OPTIONAL EQUIPMENT 1854 mm (73 in) Buckets: Long Lip (LL) Dirt ...........................................................................251 kg (553 lbs) Heavy Duty LL Dirt.........................................................................282 kg (622 lbs) Utility (LL Dirt W / Extension) .........................................................285 kg (628 lbs) Heavy Duty Utility (Heavy Duty LL Dirt W / Extension ...................316 kg (697 lbs) 2133 mm (84 in) Buckets: Long Lip (LL) Dirt ...........................................................................281 kg (620 lbs) Heavy Duty LL Dirt.........................................................................307 kg (677 lbs) Utility (LL Dirt W / Extension ..........................................................306 kg (675 lbs) Heavy Duty Utility (Heavy Duty LL Dirt W / Extension ...................343 kg (755 lbs) 2083 mm (82 in) Light Material Bucket ..........................................265 kg (584 lbs) Pallet Fork 106.7 mm (42 inch) (North America only) ............ 245 kg (540 pounds)

174

TRIM THIS EDGE LEFT PAGE Bur 87364592na

SPECIFICATIONS

BUCKET CAPACITIES STRUCK CAPACITIES

SAE HEAPED CAPACITIES

m3 (ft3)

m3 (ft3)

Long Lip (LL) Dirt & Heavy Duty LL Dirt

0.36 (12.9)

0.48 (16.8)

Utility (LL Dirt W/Extension) & Heavy Duty Utility (Heavy Duty LL Dirt W/Extension)

0.51 (18.0)

0.63 (22.4)

Long Lip (LL) Dirt & Heavy Duty LL Dirt

0.42 (14.7)

0.55 (19.4)

Utility (LL Dirt W/Extension & Heavy Duty Utility (Heavy Duty LL Dirt W/Extension)

0.58 (20.6)

0.73 (25.7)

2083 mm (82 inch) Light Material

0.74 (26.1)

0.92 (32.5)

TYPE 1854 mm (73 inch) Buckets

TRIM THIS EDGE

2133 mm (84 inch) Buckets

175

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

SPECIFICATIONS

MATERIAL WEIGHT MATERIAL

kg/m3

lbs/ft3

MATERIAL

kg/m3

lbs/ft3

TRIM THIS EDGE

Alum-Lump.

881

55

Oats

416

26

Pulverized

769

48

Peanuts - Shelled

280

17

Ashes

561-833

35-52

Peas

769

48

Bauxite

12021922

75-120

Peat - solid

753

47

Phosphate - Granular

1442

90

Beans

769

48

Potash

1089

68

Charcoal

368

23

Potatoes

769

48

Chips

288

18

Quartz - Granular

1762

110

Coal

1282

80

Rice

769

48

Coke - Lump - Loose

849-1009

53-63

Rye

705

44

Clay

368-513

23-32

Salt - Rock - Solid

2163

135

Concrete

13781778

86-111

Sand & Gravel - Dry

1730

108

Copper Ore

1666

104

2003

125

Corn - Shelled

673

42

Sand - Foundry

1522

95

Cottonseed

401

25

Shale

1410

88

Earth - Dry Loam

929-1089

58-68

Slag - Crushed

1121

70

16021666

100104

Slate

2243

130

Snow

240-801

15-50

Soybeans

743

46

Sugar Beet Pulp - Wet

561

35

Wet

Wet

Earth - Sand Gravel

1570

98

Ensilage

577

36

14901778

Sugar - Raw

961

60

Granite

93-111

Sulphur - Lumpy

1330

83

Gravel - Dry

1522

95

Taconite

1714

107

1906

119

Wheat

769

48

Ice - Crushed

593

37

Iron Ore

2323

145

Limestone - Loose Crushed

15381602

96-100

Wet

176

TRIM THIS EDGE LEFT PAGE Bur 87364592na

SPECIFICATIONS

GENERAL TORQUE SPECIFICATIONS Use the following torques when special torques are not given. These torques apply to fasteners with both UNC and UNF threads as received from suppliers dry, or when lubricated with engine oil. Not applicable if special graphities, Molydisulfide greases, or other extreme pressure lubricants are used.

PoundInches

Newton metres

1/4 inch

108 to 132

12 to 15

5/16 inch

204 to 252

23 to 28

3/8 inch

420 to 504

48 to 57

7/16 inch

54 to 64

73 to 87

1/2 inch

80 to 96

109 to 130

9/16 inch

110 to 132

149 to 179

5/8 inch

150 to 180

203 to 244

3/4 inch

270 to 324

366 to 439

7/8 inch

400 to 480

542 to 651

1.0 inch

580 to 696

787 to 944

1-1/8 inch

800 to 880

1085 to 1193

1-1/4 inch

1120 to 1240

1519 to 1681

1-3/8 inch

1460 to 1680

1980 to 2278

1-1/2 inch

1940 to 2200

2631 to 2983

Size

177

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

TRIM THIS EDGE

Grade 5 Bolts, Nuts, and Studs

SPECIFICATIONS

Grade 8 Bolts, Nuts, and Studs

PoundInches

Newton metres

1/4 inch

144 to 180

16 to 20

5/16 inch

288 to 348

33 to 39

3/8 inch

540 to 648

61 to 73

7/16 inch

70 to 84

95 to 114

1/2 inch

110 to 132

149 to 179

9/16 inch

160 to 192

217 to 260

5/8 inch

220 to 264

298 to 358

3/4 inch

380 to 456

515 to 618

7/8 inch

600 to 720

814 to 976

1.0 inch

900 to 1080

1220 to 1465

1-1/8 inch

1280 to 1440

1736 to 1953

1-1/4 inch

1820 to 2000

2468 to 2712

1-3/8 inch

2380 to 2720

3227 to 3688

1-1/2 inch

3160 to 3560

4285 to 4827

Size

TRIM THIS EDGE

NOTE: Use thick nuts with Grade 8 bolts.

178

TRIM THIS EDGE LEFT PAGE Bur 87364592na

SPECIFICATIONS

Grade 8.8 Bolts, Nuts, and Studs

Grade 10.9 Bolts, Nuts, and Studs

8.8

Size

PoundInches

Newton metres

Size

PoundInches

Newton metres

M4

24 to 36

3 to 4

M4

36 to 48

4 to 5

M5

60 to 72

7 to 8

M5

84 to 96

9 to 11

M6

96 to 108

11 to 12

M6

132 to 156

15 to 18

M8

228 to 276

26 to 31

M8

324 to 384

37 to 43

M10

456 to 540

52 to 61

M10

54 to 64

73 to 87

M12

66 to 79

90 to 107

M12

93 to 112

125 to 150

M14

106 to 127

144 to 172

M14

149 to 179

200 to 245

M16

160 to 200

217 to 271

M16

230 to 280

310 to 380

M20

320 to 380

434 to 515

M20

450 to 540

610 to 730

M24

500 to 600

675 to 815

M24

780 to 940

1050 to 1275

M30

920 to 1100

1250 to 1500

M30

1470 to 1770

2000 to 2400

M36

1600 to 1950

2175 to 2600

M36

2580 to 3090

3500 to 4200

Grade 12.9 Bolts, Nuts, and Studs 12.9

Usually the torque values specified for grade 10.9 fasteners can be used satisfactorily on grade 12.9 fasteners.

179

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

TRIM THIS EDGE

10.9

SPECIFICATIONS

450 OPERATING DATA AND DIMENSIONS

TRIM THIS EDGE

A. Dump angle at full height Dirt and Utility Bucket ....................................................................40 degrees Light Material Bucket .....................................................................35 degrees B. Dump Height, Maximum Height Dirt and Utility Bucket ........................................................ 2401 mm (94.5 in) Light Material Bucket ......................................................... 2361 mm (93.0 in) C. Dump Reach, Maximum Height Dirt and Utility Bucket .......................................................... 679 mm (26.7 in) Light Material Bucket ........................................................... 896 mm (35.3 in) D. Overall operating height, max.

Dirt and Utility Bucket ...................................................... 3817 mm (150.3 in) Light Material Bucket ....................................................... 4035 mm (158.9 in) E. Height to top of ROPS w/Standard 12 x 16.5 Tires.................................................. 2045 mm (80.5 in) F. Ground clearance To Bottom of chain case ........................................................ 229 mm (9.0 in) G. Wheel base ....................................................................... 1170 mm (46.06 in) H. Overall length without Attachment ..................................... 2761 mm (108.7 in) J. Overall length with attachment on ground Dirt and Utility Bucket ...................................................... 3576 mm (140.8 in) Light Material Bucket ....................................................... 3772 mm (148.5 in) K. Clearance circle, front (without bucket)................................ 1385 mm (54.5 in) L. Clearance circle, front (with Attachment) 1854 mm (73 in) Short Lip Dirt and Utility Bucket ............. 2140 mm (84.3 in) 1854 mm (73 in) Long Lip Dirt Bucket ............................... 2369 mm (93.3 in) 2133 mm (84in) Dirt and Utility Bucket .............................. 2192 mm (86.3 in) M. Clearance circle, rear........................................................... 1783 mm (70.2 in)

180

TRIM THIS EDGE LEFT PAGE Bur 87364592na

TRIM THIS EDGE

SPECIFICATIONS

BS05H038

181

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

SPECIFICATIONS

450 Operating Data And Dimensions N. Tread width with Standard Tires (12 x 16.5) ......................................... 1516 mm (59.7 in) O. Overall width with Standard Tires (12 x 16.5) ......................................... 2032 mm (72.0 in) P. Height to bucket hinge, fully raised .................................... 3162 mm (124.5 in) Q. Bucket width Dirt, Utility .......................................................................... 1854 mm (73.0 in) Dirt, Utility .......................................................................... 2133 mm (84.0 in) R. Height to Bottom of level bucket, Arm fully raised ........................................................................................ 2959 mm (116.5 in) S. Maximum rollback with attachment at full height ......................................................................................................55 degrees T. Maximum rollback with attachment on ground ......................................................................................................30 degrees U. Rear departure angle ......................................................................28 degrees V. Clearance to bottom of belly pan ........................................... 280 mm (11.0 in) TRIM THIS EDGE

Lift Capacity To Maximum Height...............................................2223 kg (4900 lbs) Tipping Load ............................................................................ 2223 kg (4900 lbs) Rated operating load ISO 14397-2 ............................................1111 kg (2450 lbs) Travel Speed, Forward And Reverse Low range ................................................................. 0 to 6.2 mph (0 to 10.0 km/h) High range............................................................... 0 to 11.3 mph (0 to 18.1 km/h)

182

TRIM THIS EDGE LEFT PAGE Bur 87364592na

TRIM THIS EDGE

SPECIFICATIONS

BS05H038

183

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

SPECIFICATIONS

450CT OPERATING DATA AND DIMENSIONS

TRIM THIS EDGE

A. Dump angle at full height Dirt and Utility Bucket ....................................................................40 degrees B. Dump Height, Maximum Height Dirt and Utility Bucket ........................................................ 2401 mm (94.5 in) C. Dump Reach, Maximum Height Dirt and Utility Bucket .......................................................... 780 mm (30.7 in) D. Overall operating height, max.

Dirt and Utility Bucket ...................................................... 3817 mm (150.3 in) E. Height to top of ROPS ........................................................ 2045 mm (80.5 in) F. Ground clearance To Bottom of chain case ........................................................ 229 mm (9.0 in) G. Track on ground ................................................................... 1645 mm (64.7 in) H. Overall length without Attachment ..................................... 2760 mm (108.7 in) J. Overall length with attachment on ground Dirt and Utility Bucket ...................................................... 3576 mm (140.8 in) K. Clearance circle, front (without bucket)................................ 1486 mm (58.5 in) L. Clearance circle, front (with Attachment) 2.08 m (84 in) Dirt Bucket.................................................. 2309 mm (90.9 in) M. Clearance circle, rear........................................................... 1521 mm (59.9 in)

184

TRIM THIS EDGE LEFT PAGE Bur 87364592na

TRIM THIS EDGE

SPECIFICATIONS

BS05D001

185

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

SPECIFICATIONS

Operating Data and Dimensions 450CT N. Track gauge with 400 mm track ........................................... 1615 mm (63.6 in) N. with 450 mm track ............................................................... 1661 mm (65.4 in) O. Overall width across 400 mm track...................................... 2065 mm (81.3 in) O. width across 450 mm track.................................................. 2098 mm (82.6 in) P. Height to bucket hinge, fully raised .................................... 3162 mm (124.5 in) Q. Bucket width Dirt, Utility .......................................................................... 2133 mm (84.0 in) R. Height to Bottom of level bucket, Arm fully raised ........................................................................................ 2959 mm (116.5 in) S. Maximum rollback with attachment at full height ......................................................................................................55 degrees T. Maximum rollback with attachment on ground ......................................................................................................30 degrees U. Rear departure angle ......................................................................39 degrees V. Clearance to bottom of belly pan ........................................... 280 mm (11.0 in) TRIM THIS EDGE

Lift Capacity To Maximum Height...............................................3499 kg (7174 lbs) Tipping Load ............................................................................ 3499 kg (7174 lbs) Rated operating load @ 35 % of tipping load ISO 14397-2 .......1111 kg (2450 lbs) Rated operating load @ 50 % of tipping load ISO 14397-2 .......1750 kg (3858 lbs) Travel Speed, Forward And Reverse Low range ........................................................................... 0 to 5.1 mph (0 to 8.2 ) High range................................................................. 0 to 8.0 mph (0 to 12.8 km/h)

186

TRIM THIS EDGE LEFT PAGE Bur 87364592na

TRIM THIS EDGE

SPECIFICATIONS

BS05D001

187

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

SPECIFICATIONS

465 OPERATING DATA AND DIMENSIONS

TRIM THIS EDGE

A. Dump angle at full height Dirt and Utility Bucket ....................................................................40 degrees Light Material Bucket .....................................................................35 degrees B. Dump Height, Maximum Height Dirt and Utility Bucket ........................................................ 2412 mm (95.0 in) Light Material Bucket ......................................................... 2365 mm (93.1 in) C. Dump Reach, Maximum Height Dirt and Utility Bucket .......................................................... 934 mm (36.8 in) Light Material Bucket ......................................................... 1148 mm (45.2 in) D. Overall operating height, max.

Dirt and Utility Bucket ...................................................... 4141 mm (163.0 in) Light Material Bucket ....................................................... 4327 mm (170.4 in) E. Height to top of ROPS w/(Standard 12 x 16.5 Tires) ............................................... 2045 mm (80.5 in) F. Ground clearance To Bottom of chain case ........................................................ 229 mm (9.0 in) G. Wheel base ......................................................................... 1285 mm (50.6 in) H. Overall length without Attachment ..................................... 2809 mm (110.6 in) J. Overall length with attachment on ground Dirt and Utility Bucket ...................................................... 3629 mm (142.9 in) Light Material Bucket ....................................................... 3827 mm (150.7 in) K. Clearance circle, front (without bucket)................................ 1395 mm (54.9 in) L. Clearance circle, front (with Attachment) 1854 mm (73 in) Long Lip Dirt Bucket ............................... 2381 mm (93.7 in) 2133 mm (84 in) Dirt and Utility Bucket ............................. 2244 mm (88.4 in) M. Clearance circle, rear........................................................... 1654 mm (65.1 in)

188

TRIM THIS EDGE LEFT PAGE Bur 87364592na

BS04M058

K

L

M

O

N

Q

BT97B194

189

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

TRIM THIS EDGE

SPECIFICATIONS

SPECIFICATIONS

465 Operating Data And Dimensions N. Tread width with Standard Tires (12 x 16.5 ) ........................................ 1516 mm (59.7 in) O. Overall width with Standard Tires (12 x 16.5) ......................................... 1829 mm (72.0 in) P. Height to bucket hinge, fully raised .................................... 3187 mm (125.5 in) Q. Bucket width Dirt, Utility .......................................................................... 1854 mm (73.0 in) Dirt, Utility .......................................................................... 2133 mm (84.0 in) R. Height to Bottom of level bucket, Arm fully raised ........................................................................................ 2984 mm (117.5 in) S. Maximum rollback with attachment at full height ......................................................................................................94 degrees T. Maximum rollback with attachment on ground ......................................................................................................27 degrees U. Rear departure angle ......................................................................28 degrees V. Clearance to bottom of belly pan ........................................... 280 mm (11.0 in) TRIM THIS EDGE

Lift Capacity To Maximum Height....................................... 2722 kg (6000 pounds) Tipping Load ..................................................................... 2722 kg (6000 pounds) Rated Operating Load, ISO 14397-2 .........................................1361 kg (3000 lbs) Travel Speed, Forward And Reverse Low range ................................................................. 0 to 6.2 mph (0 to 10.0 km/h) High range............................................................... 0 to 11.3 mph (0 to 18.1 km/h)

190

TRIM THIS EDGE LEFT PAGE Bur 87364592na

BS04M058

K

L

M

O

N

Q

BT97B194

191

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

TRIM THIS EDGE

SPECIFICATIONS

SPECIFICATIONS

PALLET FORK WITH BRICK GUARD Maximum width of forks (centerlines) ...................................... 1104 mm (43.5 in) Minimum width of forks (centerlines) ........................................ 101.6 mm (4.0 in) Length of fork ...........................................................................1.07 m (42 inches) Overall length of attachment .................................................... 1070 mm (42.1 in) Height-Top of Forks to Top of Brickguard Screen .............1117 mm (44.0 inches) Fork cross section ............................................... 32 x 101 mm (1.25 x 4 inches) Rated Operating Capacity @ 610 mm (24 inches) load center ground level lift breakout 450................................................................................... 717 kg (1580 pounds) 465................................................................................... 930 kg (2050 pounds) Tipping load (42 inch model) @ 610 mm (24 inches) load center 450................................................................................. 1434 kg (3160 pounds) 465................................................................................. 1888 kg (4160 pounds) TRIM THIS EDGE

Roll back angle at ground level 450 ........................................................................................................21degrees 465 .......................................................................................................21 degrees

192

TRIM THIS EDGE LEFT PAGE Bur 87364592na

INDEX Alternator Charging System .......... 163 Anti-Vandal Lockout ........................ 97 Attachment Coupler ........................ 87 Attachment Installation .................... 87 Attachment Removal ....................... 89 Auxiliary Hydraulic Attachment Controls 64 Auxiliary Hydraulic Flow Rate ......... 95

B Battery Cleaning ............................ 134 Battery Fluid Level ........................ 163 Brake Specification ....................... 173 Bucket Installation ........................... 87 Bucket Removal .............................. 89

C Cab Door Latches ........................... 71 Case Hydraulic Attachment Coupler 90 Cold Weather Operation ................. 80 Components, Machine ...................... 6 Controls Auxiliary Hydraulic Attachment ... 64 Operator Seat ............................. 69 Throttle ........................................ 61 Cooling System Specification ........ 173 Couplers Case Hydraulic Attachment ........ 90

D Dimensions, Operating . 180, 182, 184, 188, 190 Drive Chain Tension, Adjusting ..... 156

E Engine Air Filter Warning Lamp ...... 45 Engine Hourmeter ......................... 113 Engine Serial Number ....................... 4 Environment .................................. 114

F Fire Extinguisher ........................... 161 Fluids and Lubricants .................... 115 Front Work Lamps Switch ............... 44

Fuel Gauge ..................................... 43 Fuel Handling Precautions .............. 18 Fuses ............................................ 166

G Grease Fittings Bucket Pivots .................... 119, 120 Loader Lift Arm ................. 119, 120

H Hand Throttle Adjustment ............. 155 Hazardous Chemical Precautions ... 19 High Flow Rate ................................ 95 Hot Weather Operation ................... 81 Hydraulic Bypass ............................ 62 Hydraulic Bypass Control ................ 62 Hydraulic System Specification ..... 173 Hydraulics High Flow Hydraulic System ....... 94 Hydrostatic Pump Serial Number ...... 5

I Inspection, Daily .............................. 75

J Job Site Operation .......................... 84

K Key Switch Run ............................................. 42 Start ............................................ 42 Stop ............................................. 42 System Power ............................. 42

L Lamps Tail ............................................ 165 Work .......................................... 164 Loader Bucket Serial Number ........... 5 Loader Operation ............................ 85 Lowering the Operators Compartment 112 Lubricants and Fluids .................... 115 Lubrication Chart ........................... 118

193

TRIM THIS EDGE RIGHT PAGE (Chapter First Page)

TRIM THIS EDGE

A

M Machine Components ........................6 Machine Operation ...........................84 Maintenance Chart .........................118 Maintenance Lubrication Schedule 113 Maintenance Precautions ................17 Master Disconnect Switch ................49 Material Weight Specification .........176 Moving a Disabled Machine .............97

O

TRIM THIS EDGE

Oil Temperature ..............................122 Viscosity .....................................122 Operating Data 180, 182, 184, 188, 190 Operating Dimensions ..180, 182, 184, 188, 190 Operating Precautions .....................15 Operating Weight Specifications ....174 Operation Cold Weather ...............................80 Hot Weather .................................81 Job Site ........................................84 Loader ..........................................85 Operators Compartment Tilting .........................................110 Operators Compatment Lowering ....................................112 Operators Seat Deluxe ..........................................69 Optional Equipment Specification ..174

P Pallet Fork with Brick Guard ...........192 Parking brake activation ...................41 Parking Brake Lamp ........................44 Plastic and Resin Parts ..................161 Power Train Specification ..............173 Product Identification Number ............4

R Radiator Coolant Level ..................135 Rear Access Door ..........................116 Relays ............................................166 Ride Control .....................................96 Accumulator ...............................158 Roll-Over Protection Structure .......159

Damage .................................... 160 Inspection ................................. 159 Label ......................................... 159 Maintenance ............................. 159 ROPS Serial Number ........................ 5 Run-In Period .................................. 79

S Safety Decals .................................. 29 Safety, Decals, and Hand Signals Safety Rules ................................. 9 Safety/Decals/Hand Signals Safety Decals .............................. 29 Seat Belt Maintenance ............................. 158 Torque Specifications ............... 158 Seat Belt Precautions ...................... 21 Serial Number Engine ........................................... 4 Hydrostatic Pump ......................... 5 Loader Bucket ............................... 5 ROPS ............................................ 5 Starter ........................................... 5 Sliding Side Windows (If Equipped) 71 Specific machine precautions ......... 22 Specifications Brakes ....................................... 173 Cooling System ......................... 173 Hydraulic System ...................... 173 Material Weight ......................... 176 Operating Weight ...................... 174 Optional Equipment .................. 174 Power Train .............................. 173 Starter Serial Number ....................... 5 Starting and Stopping Precautions .. 14 Starting the Engine .......................... 78 Steel Track Adjustments ............... 153 Storage Preparation ............................... 169 Removal .................................... 170 Switches Front Auxiliary Electrical ............. 73 Front Work Lamps ...................... 44 Systemgard Lubrication Analysis Program .................................. 114

194

TRIM THIS EDGE LEFT PAGE Bur 87364592na

T Tail Lamps ..................................... 165 Throttle Controls Foot ............................................. 61 Hand ........................................... 61 Tilting the Operator’s Compartment ....

110 Tire Inflating ..................................... 102 Pressure .................................... 102 Towing a Machine ........................... 97 Track Length, Adjustment ............. 153 Track Sag, Checking ..................... 153 Transporting the Machine ............... 98 Travel Speeds ................................. 60 Turn Signal Switch .......................... 68

W Warning Lamp Engine Air Filter .......................... 45 Wheel Nuts .................................... 103 Windows .......................................... 71 Removal of Sliding Side Windows ..

162 Work Lamps .................................. 164

195

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

TRIM THIS EDGE

U Utility Safety .................................... 11 Utility Safety Rules Message .......... 11

TRIM THIS EDGE 196

TRIM THIS EDGE LEFT PAGE Bur 87364592na

AFTER DELIVERY CHECK AFTER FIRST 100 HOURS OF OPERATION OF NEW MACHINE Owners Name: Address: Dealers Name: Address: Machine Model Number:

Hourmeter Indication:

Machine Product Identification Number (P.I.N.): COOLING SYSTEM

GENERAL

Check the coolant levels.

Look for oil leaks and loose parts.

Check for leaks.

Check tire pressure.

FUEL SYSTEM

Tighten all hose clamps.

Check for leaks.

Check drive chain tension.

Drain water and sediment from fuel tank.

Check wheel nut torque.

Check brake operation.

Check battery.

Check the control levers for correct operation.

Check operation of starter, alternator, and instruments.

Check operators seat bar for correct operation.

Check operation of all lamps.

Check track tension. (CT)

LUBRICATION

SAFETY

Lubricate all pivot points.

Inspect the ROPS.

ENGINE

Check the safety decals and replace if necessary.

Check condition of drive belt.

Check engine oil level.

Check the operator restraint system.

Check engine speed at idle and at full throttle.

Make sure the Operator’s Manual is in the manual storage box.

Check the Operator Seat Presence Switch.

HYDRAULIC SYSTEM Check the oil level.

Check pressure setting of main relief valve.

Check the restraint bar and interlock function.

Replace the hydraulic oil filter.

Check the final drive fluid. (CT)

DEALER: Make sure the owner and/or operator understands all the safety and information decals, the service information, and the service procedures in this manual.

Technician Signature: Dealer Signature: Owner Signature:

197

TRIM THIS EDGE RIGHT PAGE (Section First Page) Bur 87364592na

TRIM THIS EDGE

ELECTRICAL SYSTEM

TRIM THIS EDGE 198

TRIM THIS EDGE LEFT PAGE Bur 87364592na

AFTER DELIVERY CHECK AFTER FIRST 100 HOURS OF OPERATION OF NEW MACHINE Owners Name: Address: Dealers Name: Address: Machine Model Number:

Hourmeter Indication:

Machine Product Identification Number (P.I.N.): COOLING SYSTEM

GENERAL

Check the coolant levels.

Look for oil leaks and loose parts.

Check for leaks.

Check tire pressure.

FUEL SYSTEM

Tighten all hose clamps.

Check for leaks.

Check drive chain tension..

Drain water and sediment from fuel tank.

Check wheel nut torque.

Check brake operation.

Check battery.

Check the control levers for correct operation.

Check operation of starter, alternator, and instruments.

Check operators seat bar for correct operation.

Check operation of all lamps.

Check track tension. (CT)

LUBRICATION

SAFETY

Lubricate all pivot points.

Inspect the ROPS.

ENGINE

Check the safety decals and replace if necessary.

Check condition of drive belt.

Check engine oil level.

Check the operator restraint system.

Check engine speed at idle and at full throttle.

Make sure the Operator’s Manual is in the manual storage box.

Check the Operator Seat Presence Switch.

HYDRAULIC SYSTEM Check the oil level.

Check pressure setting of main relief valve.

Check the restraint bar and interlock function.

Replace the hydraulic oil filter.

Check the final drive fluid. (CT)

DEALER: Make sure the owner and/or operator understands all the safety and information decals, the service information, and the service procedures in this manual.

Technician Signature: Dealer Signature: Owner Signature:

199

TRIM THIS EDGE RIGHT PAGE Bur 87364592na

TRIM THIS EDGE

ELECTRICAL SYSTEM

TRIM THIS EDGE 200

TRIM THIS EDGE LEFT PAGE Bur 87364592na