Bobcat 864 & 864 High Flow Loader Operation & Maintenance Manual 6900953 - PDF DOWNLOAD

TURBO

S/N 518911001 thru 14999 S/N 516811001 thru 14999 S/N 517511001 thru 14999

Dealer Copy -- Not for Resale

TURBO

Operation & Maintenance Manual

Doosan purchased Bobcat Company from Ingersoll-Rand Company in 2007. Any reference to Ingersoll-Rand Company or use of trademarks, service marks, logos, or other proprietary identifying marks belonging to Ingersoll-Rand Company in this manual is historical or nominative in nature, and is not meant to suggest a current affiliation between Ingersoll-Rand Company and Bobcat Company or the products of either.

EQUIPPED WITH BOBCAT INTERLOCK CONTROL SYSTEM (BICS) 6900953 (12-06) Revised (6-12) (4) 1 of 134

Printed in U.S.A.

© Bobcat Company 2006

2 of 134

Dealer Copy -- Not for Resale

OPERATOR SAFETY WARNINGS CORRECT

WARNING

Operator must have instructions before running the machine.

Untrained operators can cause injury or death.

W-2001-1285

Never use the loader without instructions. See machine signs (decals), Operation & Maintenance Manual, and Operator’s Handbook.

CORRECT

CORRECT

WRONG

B-15570

B-15652

B-15653

Always use the seat bar and fasten seat belt snugly.

Always keep feet on the foot pedals or footrests when operating loader.

Never use loader without operator cab with ROPS and FOPS approval.

Fasten your seat belt.

Never use loader as man lift or elevating device for personnel.

WRONG

WRONG

WRONG

B-15260

B-15654

B-15655

Do not use loader in atmosphere with explosive dust, explosive gas, or where exhaust can contact flammable material.

Never exceed Capacity.

B-10731a

Never carry riders.

Keep bystanders away from work area.

Always carry bucket or attachments as low as possible.

Do not travel or turn with lift arms up.

Load, unload, and turn on flat level ground.

WRONG

WRONG

WRONG

B-15656

B-15661

B-15658

Rated

Operating

Never leave loader with engine running or with lift arms up.

To park, engage parking brake and put attachment flat on the ground.

Never modify equipment.

Use only attachments approved by Bobcat Company for this model loader.

SAFETY EQUIPMENT The Bobcat Loader must be equipped with safety items necessary for each job. Ask your dealer for information on the safe use of attachments and accessories.

1. SEAT BELT: Check belt fasteners and check for damaged webbing or buckle.

2. SEAT BAR: When up, it must lock the loader controls.

3. OPERATOR CAB (ROPS and FOPS): It must be on the loader with all fasteners tight.

4. HANDBOOK: Must be in the cab.

5. SAFETY SIGNS (DECALS): Replace if damaged.

6. SAFETY TREADS: Replace if damaged.

7. GRAB HANDLES: Replace if damaged.

8. LIFT ARM SUPPORT DEVICE: Replace if damaged.

9. PARKING BRAKE 10. BOBCAT INTERLOCK CONTROL SYSTEM (BICS) OSW10-0805 3 of 134

Dealer Copy -- Not for Resale

Safety Alert Symbol: This symbol with a warning statement, means: “Warning, be alert! Your safety is involved!” Carefully read the message that follows.

4 of 134

Dealer Copy -- Not for Resale

FOREWORD

CONTENTS FOREWORD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . III SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . XI

SAFETY

OPERATING INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . OI-1 PREVENTIVE MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . PM-1 SYSTEM SETUP & ANALYSIS. . . . . . . . . . . . . . . . . . . . . . . . . . SA-1 MACHINE SIGN TRANSLATIONS . . . . . . . . . . . . . . . . . . . . . . MST-1 SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SPEC-1

OPERATING INSTRUCTIONS

PREVENTIVE MAINTENANCE

SYSTEM SETUP & ANALYSIS

REFERENCE INFORMATION

Dealer Copy -- Not for Resale

Write the correct information for YOUR Bobcat Loader in the spaces below. Always use these numbers when referring to your Bobcat Loader.

MACHINE SIGN TRANSLATIONS

Loader Serial Number Engine Serial Number

SPECIFICATIONS NOTES:

YOUR BOBCAT DEALER: ADDRESS: PHONE:

Bobcat Company P.O. Box 128 Gwinner, ND 58040-0128 Bobcat Company Europe Dréve Richelle 167 B-1410 WATERLOO Belgium

I 5 of 134

864 Bobcat Loader Operation & Maintenance Manual

Dealer Copy -- Not for Resale II 6 of 134

864 Bobcat Loader Operation & Maintenance Manual

FOREWORD

FOREWORD This Operation & Maintenance Manual was written to give the owner/operator instructions on the safe operation and maintenance of the Bobcat Loader. READ AND UNDERSTAND THIS OPERATION & MA INTENANCE MANUAL BEFORE OPERATING YOUR machine. If you have any questions, see your Bobcat dealer.

BOBCAT COMPANY IS ISO 9001:2000 CERTIFIED . . . . . . . . . . . . V BOBCAT LOADER IDENTIFICATION. . . . . . . . . . . . . . . . . . . . . . . VIII DELIVERY REPORT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VII FEATURES AND ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . IX MOTOR OIL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . V

SERIAL NUMBER LOCATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . VII Engine Serial Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VII Loader Serial Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VII

SYSTEM SETUP & ANALYSIS Dealer Copy -- Not for Resale

REGULAR MAINTENANCE ITEMS . . . . . . . . . . . . . . . . . . . . . . . . . V

TRANSLATIONS

III 7 of 134

864 Bobcat Loader Operation & Maintenance Manual

Dealer Copy -- Not for Resale IV 8 of 134

864 Bobcat Loader Operation & Maintenance Manual

BOBCAT COMPANY IS ISO 9001:2000 CERTIFIED

ISO 9001:2000 is a set of international standards that control the processes and procedures which we use to design, develop, manufacture, distribute, and service Bobcat products.

British Standards Institute (BSI) is the Certified Registrar Bobcat chose to assess the Company’s compliance with the ISO 9001:2000 set of s tandards. The BSI registration certifies that the two Bobcat manufacturing plants and the Bobcat corporate offices (Gwinner, Bismarck & West Fargo) in North Dakota are in compliance with ISO 9001:2000. Only certified assessors, like BSI, can grant registrations.

ISO 9001:2000 means that as a company we say what we do and do what we say. In other words, we have established procedures and policies, and we provide evidence that the procedures and policies are followed.

Diesel engine exhaust and some of its constituents are known to the State of California to cause cancer, birth defects and other reproductive harm.

REGULAR MAINTENANCE ITEMS ENGINE OIL FILTER (6 Pack) 6665603

BATTERY 6665427

FUEL FILTER 6667352

FLUID, BLACK GOLD Hydraulic / Hydrostatic (2, 2-1/2 Gallon Containers) 6563328

AIR FILTER, Outer 6666375 AIR FILTER, Inner 6666376

NOTE: Always verify Part Numbers with your Bobcat dealer.

MOTOR OIL 6667299 - SAE 15W40 CE/SG (12 qt.)

6657301 - SAE 10W30 CE/SG (12 qt.)

6657303 - SAE 30W CE/SG (12 qt.)

6724558 - SAE 15W40 CE/SG (1 Gal.) 6724557 - SAE 10W30 CE/SG (1 Gal.) 6724559 - SAE 30W CS/SG (1 Gal.)

V 9 of 134

6674204 - SAE 15W40 CE/SG (2.5 Gal.) 6674205 - SAE 10W30 CE/SG (2.5 Gal.) 6674206 - SAE 30W CS/SG (2.5 Gal.)

864 Bobcat Loader Operation & Maintenance Manual

Dealer Copy -- Not for Resale

CALIFORNIA PROPOSITION 65 WARNING

Dealer Copy -- Not for Resale VI 10 of 134

864 Bobcat Loader Operation & Maintenance Manual

SERIAL NUMBER LOCATIONS

Engine Serial Number

Always use the serial number of th e loader when requesting service information or when ordering parts.

Early or later models (identification made by serial number) may use different parts, or it may be necessary to use a different procedure in doing a specific service operation.

Figure 2

Loader Serial Number Figure 1

P-10443

N-19358

The loader serial number plate is located on the outside of the loader frame [Figure 1].

Explanation of loader Serial Number:

N-19359

The engine serial number is located on the valve cover at the right side of the engine [Figure 2]. There is also an extra S/N tag attached to the engine [Figure 3].

DELIVERY REPORT Figure 4 1. The four digit Model/Engine Combination Module number identifies the model number and engine combination.

2. The five digit Production Sequence Number identifies the order which the loader is produced.

The Delivery Report must be filled out by the dealer and signed by the owner or operator when the Bobcat Loader is delivered. An explanation of the form must be given to the owner. Make sure it i s filled out completely [Figure 4].

VII 11 of 134

864 Bobcat Loader Operation & Maintenance Manual

Dealer Copy -- Not for Resale

Figure 3

BOBCAT LOADER IDENTIFICATION FRONT LIGHTS

GRAB HANDLES OPERATOR SEAT STEERING LEVER SEAT BELT REAR AUXILIARY QUICK COUPLERS

TILT CYLINDER FRONT AUXILIARY

†BUCKET

QUICK COUPLERS SAFETY TREAD

REAR WINDOW zOPERATOR CAB (ROPS & FOPS) REAR GRILL SEAT BAR LIFT ARM

LIFT ARM SUPPORT DEVICE REAR

LIFT CYLINDER

LIGHT TAIL LIGHT

REAR DOOR

TRACKS OPTIONAL OR FIELD ACCESSORY (Not Standard Equipment) † BUCKET - Several different buckets and other attachments are available for the Bobcat Loader. z ROPS, FOPS - Roll Over Protective Structure, per SAE J1040 and ISO 3471, and Falling Object Protective Structure per SAE J1043 and ISO 3449, Level I. Level II is available. The Bobcat Loader is base-equipped with a standard operator cab as shown. Extra insulated cab is available as an option (Reduced noise level).

VIII 12 of 134

864 Bobcat Loader Operation & Maintenance Manual

Dealer Copy -- Not for Resale

BUCKET STEPS

FEATURES AND ACCESSORIES Model 864 Bobcat Loaders are equipped with the following Standard items: Bob-Tach Turbo Charger (Approved Spark Arrestor) Lift Arm Support Device Deluxe Operator Cab (with ROPS & FOPS Approval) Bobcat Interlock Control System (BICS) Seat Belt Seat Bar Parking Brake Gauges/Warning Lights Automatically Activated Glow Plugs Deluxe Suspension Seat (Vinyl) Dual Path Cooling System Front Auxiliary Hydraulics Front and Rear Lights Rubber Tracks - 12.6 inch (320 mm)

Operator Cab

Instrumentation

FOPS Kit (Level II) Rear Window Wiper Side Windows Cab Door Vinyl Cab Enclosure Heater Kit Deluxe Suspension Seat (Cloth) Horn Back-up Alarm Cover Kit (Pedals Area) Fire Extinguisher Strobe Light or Rotating Beacon Flasher Lights Kit 3 inch Wide Seat Belt Seat Belt with 3-Point Restraint Special Applications Kit* Air Conditioning

Deluxe Instrumentation Panel (Includes Keyless Start) Automatic Shutdown Feature (For Standard Panel) Hydraulics Rear Auxiliary Hydraulics Hydraulic Bucket Positioning (Includes On/Off Selection) Power Bob-Tach (Hydraulic Wedge Engagement) Hydraulic Control Options Advanced Hand Controls (AHC) Advanced Control System (ACS) (Selectable Foot Pedal or Hand Control) Other Catalytic Exhaust Purifier Engine Heater Single Point Lift Four Point Lift Radiator Screen Kit Rear Door Lock Dual Attachment Control Kit G-Series 7-Pin Attachment Control Kit Weighlog Kit

* Includes Lexan Front Door; Top & Rear Windows Specifications subject to change without notice

IX 13 of 134

864 Bobcat Loader Operation & Maintenance Manual

Dealer Copy -- Not for Resale

Below is a list of some equipment available from your Bobcat Loader dealer as Dealer and / or Factory Installed Accessories. See your Bobcat dealer for other available options, accessories and attachments.

Dealer Copy -- Not for Resale X 14 of 134

864 Bobcat Loader Operation & Maintenance Manual

SAFETY MACHINE SIGNS (DECALS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .XVI SAFETY

Dealer Copy -- Not for Resale

SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . XIII Before Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . XIII Fire Prevention. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . XV Safe Operation Is The Operator’s Responsibility. . . . . . . . . . . .XIV Safe Operation Needs A Qualified Operator . . . . . . . . . . . . . . .XIV

XI 15 of 134

864 Bobcat Loader Operation & Maintenance Manual

Dealer Copy -- Not for Resale XII 16 of 134

864 Bobcat Loader Operation & Maintenance Manual

•

An Operator’s Handbook is fastened to the operator cab of t he Loader. It’s brief instructions are convenient to the operator. The Handbook is available from your dealer in an English edition or one of many other languages. See your Bobcat dealer for more information on translated versions.

•

The AEM Safety Manual delivered with the machine gives general safety information.

•

The Skid-Steer Loader Operating Training Course is available through your Bobcat dealer. This course is intended to provide rules and practices of correct operation of the Bobcat Loader. The course is available in English and Spanish versions.

•

Service Safety Training Courses are available from your Bobcat dealer. They provide information for safe and correct service procedures.

•

See the PUBLICATIONS AND TRAINING RESOURCES Page in t his manual or y our Bobcat dealer for Service and Parts Manuals, printed materials, videos, or training courses available. Also check the Bobcat web si tes www.training.bobcat.com or www.bobcat.com

Before Operation Carefully follow the operating instructions in this manual.

and

maintenance

The Bobcat Loader is highly maneuverable and compact.

It is rugged and useful under a wide variety of conditions.

This presents an operator with hazards associated with off highway, rough terrain applications, common with Bobcat Loader usage.

The Bobcat Loader has an internal combustion engine with resultant heat and exhaust. All exhaust gasses can kill or cause illness so use the Loader with adequate ventilation.

The dealer explains the capabilities and restrictions of the Bobcat Loader and attachment for each application.

The dealer demonstrates the safe operation according to Bobcat instructional materials, which are also available to operators. The dealer can also identify unsafe modifications or use of unapproved attachments. The attachments and buckets are designed for a Rated Operating Capacity (some have restricted lift heights).

They are designed for secure fastening to the Bobcat Loader. The user must check with the dealer, or Bobcat literature, to determine safe loads of materials of specified densities for the mac hine - attachment combination.

The dealer and owner/operator review the recommended uses of the product when delivered. If the owner/operator will be using the machine for a different application(s) he or she must ask the dealer for recommendations on the new use.

The following publications and training materials provide information on the safe use and maintenance of the Bobcat machine and attachments: •

The Delivery Report is used to assure that complete instructions have been given to the new owner and that the machine and attachment is in safe operating condition.

•

The Operation & Maintenance Manual delivered with the machine or attachment gives operating information as well as routine maintenance and service procedures. It is a part of the machine and can be stored in a container provided on the machine.

Replacement Operation & Maintenance Manuals can be ordered from your Bobcat dealer.

•

Machine signs (decals) instruct on the safe operation and care of your Bobcat machine or attachment. The signs and their locations are shown in the Operation & Maintenance Manual. Replacement signs are available from your Bobcat dealer.

Call Before You Dig 1-888-258-0808 When you call, you will be directed to a location in your state/city for information about buried lines (telephone, cable TV, water, sewer, gas, etc.)

SI SSL-0206

XIII 17 of 134

864 Bobcat Loader Operation & Maintenance Manual

Dealer Copy -- Not for Resale

SAFETY INSTRUCTIONS

SAFETY INSTRUCTIONS (CONT’D)

A Qualified Operator Must Do The Following:

Safe Operation Is The Operator’s Responsibility

Understand the Written Instructions, Rules and Regulations

Safety Alert Symbol

•

The written instructions from Bobcat Company include the Delivery Report, Operation & Maintenance Manual, Operator’s Handbook, Safety Manual and machine signs (decals).

•

Check the rules and regulations at your location. The rules may include an employer’s work safety requirements. Regulations may apply to local driving requirements or use of a Slow Moving Vehicle (SMV) emblem. Regulations may identify a hazard such as a utility line.

This symbol with a warning statement means: “Warning, be alert! Your safety is involved!”

Carefully read the message that follows.

WARNING Operator must have instructions before running the machine. Untrained operators can cause injury or death.

•

Operator training must consist of a demonstration and verbal instruction. This training is given by your Bobcat dealer before the product is delivered.

•

The new operator must start in an area without bystanders and use all the controls until he or she can operate the machine and attachment safely under all conditions of the work area. Always fasten seat belt before operating.

•

Operator Training Courses are available from your Bobcat dealer in English and Spanish. They provide information for safe and efficient equipment operation. Safety videos are also available.

•

Service Safety Training Courses are available from your Bobcat dealer. They provide information for safe and correct service procedures.

W-2001-1285

IMPORTANT This notice identifies procedures which must be followed to avoid damage to the machine.

I-2019-0284

WARNING Warnings on the machine and in the manuals are for your safety. Failure to obey warnings can cause injury or death.

Know the Work Conditions

W-2044-1285

•

Know the weight of the materials being handled.

Avoid exceeding the Ra ted Operating Capacity (R.O.C.) of the machine. Material which is very dense will be heavier than the same volume of less dense material. Reduce the size of the load if handling dense material.

•

The operator must know any prohibited uses or work areas, for example, he or she needs to kn ow about excessive slopes.

•

Know the location of any underground lines. Call local utilities or the TOLL FREE phone number found in the Before Operation Section of this manual.

•

Wear tight fitting clothing. Always wear safety glasses when doing maintenance or service. Safety glasses, hearing protection or Special Applications Kits are required for some work. See your Bobcat dealer about Bobcat Safety Equipment for your model.

The Bobcat Loader and attachment must be in good operating condition before use.

Check all of the items on the B obcat Service Schedule Decal under the 8-10 hour column or as shown in the Operation & Maintenance Manual.

Safe Operation Needs A Qualified Operator For an operator to be qualified, he or she must not use drugs or alcoholic drinks which impair alertness or coordination while working. An operator who is taking prescription drugs must get medical advice to determine if he or she can safely operate a machine.

SI SSL-0206 XIV 18 of 134

864 Bobcat Loader Operation & Maintenance Manual

Dealer Copy -- Not for Resale

Have Training with Actual Operation

SAFETY INSTRUCTIONS (CONT’D)

•

Use the procedure in the Operation & Maintenance Manual for connecting the battery and for jump starting.

•

Use the procedure in the Operation & Maintenance Manual for cleaning the spark arrestor muffler (if equipped).

Fire Prevention The machines and some attachments have components that are at high temperatures under normal operating conditions. The primary source of high temperatures is the engine and exhaust system. The electrical system, if damaged or incorrectly maintained, can be a so urce of arcs or sparks.

Figure 1

Flammable debris (leaves, straw, etc.) must be removed regularly. If flammable debris is allowed to accumulate, it can cause a fire hazard. Clean often to av oid this accumulation. Flammable debris in the engine compartment is a potential fire hazard.

•

Do not use the machine where exhaust, arcs, sparks or hot components can contact flammable material, explosive dust or gases.

•

The operator cab, engine compartment and engine cooling system must be inspected every day and cleaned if necessary to prevent fire hazards and overheating.

•

Check all electrical wiring and connections for damage. Keep the battery terminals clean and tight.

Repair or replace any damaged part.

•

Check fuel and hydraulic tubes, hoses and fittings for damage and leakage. Never use open flame or bare skin to check for leaks. Tighten or replace any parts that show leakage. Always clean fluid spills. Do no t use gasoline or diesel fuel for cleaning parts. Use commercial nonflammable solvents.

•

Do not use ether or starting fluids on any engine that has glow plugs. These starting aids can cause explosion and injure you or bystanders.

•

Always clean the machine, disconnect the battery, and disconnect the wiring from the Bobcat controllers before welding. Cover rubber hoses, battery and all other flammable parts. Keep a fire extinguisher near the machine when welding. Have good ventilation when grinding or welding painted parts. Wear dust mask when grinding painted parts. Toxic dust or gas can be produced.

•

Stop the engine and let it cool before adding fuel. No smoking!

•

Know where fire extinguishers and first aid kits are located and how to use them. Fire extinguishers are available from your Bobcat dealer [Figure 1].

Sl SSL-0206

XV 19 of 134

864 Bobcat Loader Operation & Maintenance Manual

Dealer Copy -- Not for Resale

The spark arrestor exhaust system is designed to control the emission of hot particles from the engine and exhaust system, but the muffler and the ex haust gases are still hot.

MACHINE SIGNS (DECALS)

Dealer Copy -- Not for Resale

Follow the instructions on all the Machine Signs (Decals) that are on the loader. Replace any damaged machine signs and be sure they are in the correct locations. Machine signs are available from your Bobcat Loader dealer.

XVI 20 of 134

864 Bobcat Loader Operation & Maintenance Manual

Dealer Copy -- Not for Resale

MACHINE SIGNS (DECALS) (CONT’D)

XVII 21 of 134

864 Bobcat Loader Operation & Maintenance Manual

Dealer Copy -- Not for Resale XVIII 22 of 134

864 Bobcat Loader Operation & Maintenance Manual

OPERATING INSTRUCTIONS ATTACHMENTS AND BUCKETS ...................................................................OI-27 Hand Lever Bob-Tach ................................................................................OI-28 Power Bob-Tach.........................................................................................OI-30 DAILY INSPECTION .......................................................................................OI-19

HYDRAULIC CONTROLS...............................................................................OI-12 Attachment Auxiliary Hydraulics (If Equipped) Auxiliary Hydraulics ButtonOI-14 Attachment Control Device (ACD) (If Equipped)........................................OI-17 Bucket Position Valve Operation (If Equipped) ..........................................OI-18 Foot Pedals................................................................................................OI-12 FRONT Auxiliary Hydraulics Operation .....................................................OI-15 Hand Controls (If Equipped) ......................................................................OI-12 High-Flow Hydraulics Operation (If Equipped)...........................................OI-16 Quick Couplers ..........................................................................................OI-13 REAR Auxiliary Hydraulics Operation........................................................OI-15 Releasing Hydraulic Pressure (Loader and Attachment)...........................OI-14 Secondary Front Auxiliary Hydraulics (If Equipped) ..................................OI-16

OPERATING INSTRUCTIONS

INSTRUMENT PANEL IDENTIFICATION .........................................................OI-3 Cab Light......................................................................................................OI-8 Front Accessory Panel.................................................................................OI-7 Left Panel - Standard and Deluxe Instrument Panels ..................................OI-3 Option and Field Accessory Panels (If Equipped) .......................................OI-7 Right Panel - Deluxe Instrument Panel (With Keyless Start) .......................OI-5 Right Panel - Standard Instrument Panel (With Key Switch) .......................OI-4 Side Accessory Panel ..................................................................................OI-7 LIFT ARM BY-PASS CONTROL .......................................................................OI-8 LIFTING THE LOADER...................................................................................OI-40 Four Point Lift.............................................................................................OI-40 Single Point Lift ..........................................................................................OI-40 MONITORING THE DISPLAY PANEL ............................................................OI-26 Continued On Next Page

OI-1 23 of 134

864 Bobcat Loader Operation & Maintenance Manual

Dealer Copy -- Not for Resale

ENGINE SPEED CONTROL.............................................................................OI-9

OPERATING INSTRUCTIONS (CONT’D) OPERATING PROCEDURES .......................................................................... OI-32 Backfilling (Foot Pedals) ............................................................................. OI-37 Backfilling (Hand Controls) ......................................................................... OI-37 Compact Track Loader Operating Tips ....................................................... OI-33 Digging Into the Ground (Foot Pedals) ....................................................... OI-36 Digging Into the Ground (Hand Controls) ................................................... OI-37 Emptying the Bucket (Foot Pedals) ............................................................ OI-35 Emptying the Bucket (Hand Controls)......................................................... OI-35 Filling the Bucket (Foot Pedals) .................................................................. OI-34 Filling the Bucket (Hand Controls) .............................................................. OI-34 Leveling the Ground (Using Lift Arms in Float Position) (Foot Pedals)....... OI-35 Leveling the Ground (Using Lift Arms in Float Position) (Hand Controls) ... OI-36 PARKING BRAKE (EARLY MODELS) ............................................................... OI-9 PARKING BRAKE (LATER MODELS) ............................................................... OI-9

STARTING THE ENGINE................................................................................. OI-22 Cold Temperature Starting .......................................................................... OI-24 Deluxe Instrument Panel (With Keyless Start) ............................................ OI-23 Standard Instrument Panel (With Key Switch) ............................................ OI-22 Warming The Hydraulic/Hydrostatic System............................................... OI-24 SEAT BAR RESTRAINT SYSTEM................................................................... OI-11 STEERING LEVERS........................................................................................ OI-10 STOPPING THE BOBCAT LOADER ............................................................... OI-10 STOPPING THE ENGINE ................................................................................ OI-25 TOWING THE LOADER................................................................................... OI-39 TRACTION LOCK OVERRIDE .......................................................................... OI-8 TRANSPORTING THE BOBCAT LOADER ..................................................... OI-38

OI-2 24 of 134

864 Bobcat Loader Operation & Maintenance Manual

Dealer Copy -- Not for Resale

PRE-STARTING PROCEDURE ....................................................................... OI-20

INSTRUMENT PANEL IDENTIFICATION

Left Panel - Standard and Deluxe Instrument Panels

Figure OI-1

The left instrument panel [Figure OI-1] is the same for both Standard and the Deluxe (Option) Instrument Panels.

REF NO DESCRIPTION

FUNCTION / OPERATION

1

TEMPERATURE GAUGE

Shows the engine coolant temperature.

2

HOURMETER / CODE DISPLAY / GLOW PLUG COUNTDOWN

HOURMETER - Records operating hours of loader. CODE DISPLAY - Displays alphanumeric SERVICE CODES* relating to the loader monitoring system. COUNTDOWN - Glow Plug time remaining.

3

FUEL GAUGE

Shows the amount of fuel in the tank.

4

LIGHTS / HOLD FOR CODES

LIGHTS - Press once for FRONT LIGHTS. Press a second time for FRONT AND REAR lights. Press a third time to turn all lights off. HOLD FOR CODES - P ress and hold t wo seconds for display of SERVICE CODES* (Item 2). (CODES* show only when there is an err or found by loader m onitoring system.)

5

BUCKET POSITIONING (BP) (Option)

Press to engage B P function. Press again to disengage. Press & hold 2 seconds to view B ASE or Shtdn ( SHUTDOWN) feature in HOURMETER / CODE DSIPLAY. Also shows Operational Code Number.

ATTACHMENT AUXILIARY HYDRAULICS 6

HIGH FLOW (Option)

Press to engage the HIGH FLOW auxiliary hydraulics. Press again to disengage.

7

MAXIMUM FLOW / VARIABLE FLOW

Press once to engage the VARIABLE FLOW auxiliary hydraulics. Press a second time to engage MAXIMUM FLOW. Press a third time to disengage all auxiliary hydraulics. [VARIABLE FLOW allows for slow-to-fast movement of auxiliary functions (The farther you move the switch, the faster the movement of auxiliary functions.) MAXIMUM FLOW allows for only fast movement.]

8

AUXILIARY PRESSURE RELEASE

Press and hold for two seconds. The engine will stop. Auxiliary circuit hydraulic pressure will be released. Turn key OFF (Standard Panel); or press STOP Button (Deluxe Panel).

BOBCAT INTERLOCK CONTROL SYSTEM (BICS) (See SYSTEM SETUP AND ANALYSIS, Page SA-3 for troubleshooting BICS) 9

PRESS TO OPERATE LOADER

Press to activate BICS System when the Seat Bar is do wn and operat or is s eated in operating position.

10

SEAT BAR

The light comes ON when the seat bar is down.

11

LIFT & TILT VALVE

The light comes ON when the seat bar is down and the PRESS TO OPERATE Button is pressed. The lift and tilt functions can be operated when the light is ON.

12

TRACTION

The light comes ON when the seat bar is down, engine is running, and parking brake is released. The loader can be moved forward or backward when the light is ON.

13

TRACTION LOCK OVERRIDE

(Functions Only When Seat Bar Is Raised And The Engine Is Running) Press to unlock the brakes.

Allows you to use the steering levers to move the loader forward or backward when using the backhoe attachment or for loader service. (See TRACTION LOCK OVERRIDE on Page OI-8.)

Press a second time to lock the brakes.

14

ALARM

The ALARM beeps when there is an Error, WARNING or SHUTDOWN condition.

* See SYSTEM SETUP & ANALYSIS, Page SA-3 for further description of SERVICE CODES. SHUTDOWN feature only in Deluxe Right Panel or Factory Option with Standard Panel.

25 of 134

OI-3

864 Bobcat Loader Operation and Maintenance Manual

Dealer Copy -- Not for Resale

The table below shows the DESCRIPTION and FUNCTION / OPERATION for each of the components of the left panel.

INSTRUMENT PANEL IDENTIFICATION (CONT’D)

Figure OI-2

Right Panel - Standard Instrument Panel (With Key Switch) The right instrument panel shown [Figure OI-2] is the Standard Panel.

Dealer Copy -- Not for Resale

The table below shows the Icons and other components of the Right Standard Panel.

26 of 134

OI-4

864 Bobcat Loader Operation and Maintenance Manual

INSTRUMENT PANEL IDENTIFICATION (CONT’D)

Figure OI-4

Right Panel - Deluxe Instrument Panel (With Keyless Start)

The first screen you will see on your new loader will be as shown in [Figure OI-4].

When this screen is on the display you can enter the password and start the e ngine or change the Display Panel setup features.

1. Display Panel: The Display Panel [Figure OI-3] is where all system setup, monitoring, troubleshooting, and error conditions are displayed.

NOTE: Loaders with Deluxe Instrument Panel have a permanent, randomly generated Master Password set at the factory. Your loader will be assigned an Owner Password. Your dealer will provide you with this password. Change the password to one that you will easily remember to prevent unauthorized use of your loader. (See Passwords on Page SA-7.)

Keep your password in a safe place for future needs.

2. Function Icons: The lower left area of the Deluxe Panel has the same Icons as the Standard Panel (See Page 4). These Icons are only visible when the monitoring system has detected an error.

3. Selection Buttons: The four Selection Buttons allow you to select items from the Display Panel and scroll through screens.

4. Keypad: The numeric keypad (Item 4) [Figure OI-3] has two functions:

Start Engine: Use the Keypad to enter the numbers (letters) of y our password and press the RU N / ENT ER key (Item 5) [Figure OI-3].

(a) To enter a nu mber code (password) to allow starting the engine (Keyless Start).

Press and hold the START Button (Item 6) [Figure OI-3] until the engine starts. (Always preform the PRESTARTING PROCEDURE on Page OI-20 before starting the engine.)

(b) To enter a num ber as directed for further use of the Display Panel.

Press the STOP Button (Item 7) [Figure OI-3] to stop the engine.

Change Language: Press the Selection Button at the end of the arrow [Figure OI-4] to go to the next screen.

27 of 134

OI-5

864 Bobcat Loader Operation and Maintenance Manual

Dealer Copy -- Not for Resale

Figure OI-3

INSTRUMENT PANEL IDENTIFICATION (CONT’D) Right Panel - Deluxe Instrument Panel (With Keyless Start) (Cont’d) Figure OI-5

B-16655

Dealer Copy -- Not for Resale

Use the Keypad to s elect the number of t he language [Figure OI-5].

Press EXIT. The screen will return to [Figure OI-4]. You can then enter the password and start the engine.

See DELUXE INSTRUMENT PANEL SETUP for further description of screens to setup the system for your use.

(See DELUXE INSTRUMENTATION PANEL SETUP on Page SA-6.)

NOTE: Pressing the EXIT key will go to the previous screen and you can continue pressing until you get to the initial (home) screen.

SHORTCUT: Press the "0" (zero) key to get to the home screen immediately.

28 of 134

OI-6

864 Bobcat Loader Operation and Maintenance Manual

INSTRUMENT PANEL IDENTIFICATION (CONT’D)

REF. NO. DESCRIPTION

Option and Field Accessory Panels (If Equipped)

FUNCTION / OPERATION

4.

REAR WIPER

Press the bottom of the switch to start the rear wiper. Press the top of the switch to provide washer fluid to clean the rear window.

5.

NOT USED

---

6.

NOT USED

---

7.

FAN MOTOR

Turn clockwise to increase fan speed; counterclockwise to decrease. There are four positions; OFF - 1 - 2 - 3.

8.

AIR CONDITIONING

Press the top of the switch to start; press the bottom to stop. (Fan switch must be on for A/ C to operate).

9.

TEMPERATURE CONTROL

Turn clockwise to increase the temperature; counterclockwise to decrease.

Figure OI-6

Dealer Copy -- Not for Resale

Figure OI-8

Figure OI-7

Front Accessory Panel [Figure OI-8] REF. DESCRIPTION FUNCTION / OPERATION NO.

Side Accessory Panel [Figure OI-6] and [Figure OI-7] REF. NO. DESCRIPTION

FUNCTION / OPERATION

1.

POWER PLUG

Provides a 12V receptacle for accessories.

2.

NOT USED

---

3.

FRONT WIPER

Press the top of the switch to start the front wiper (press and hold f or washer fluid).

Press the bottom of the switch to stop the wiper.

29 of 134

OI-7

10.

POWER BOB-TACH

Press and hold t he up arrow to disengage the Bob-Tach wedges. Press and hold the down arrow to engage the wedges into the mounting frame holes.

11.

NOT USED

---

12.

TURN SIGNAL Indicates left or right TURN SIGNALS are ON. INDICATORS

13.

HAZARD LIGHTS

Press the left side (or top) to turn the HAZARD LIGHTS ON; right side (or bottom) to turn OFF.

14.

ROTATING BEACON

Press the left side (or t op) to turn the ROTATING BEACON ON; right side (or bottom) to turn OFF.

15.

PARKING BRAKE

Press the top to engage the PARKING BRAKE; bottom to disengage.

16.

ADVANCED CONTROL SYSTEM (ACS)

Press the top to select Hand Controls; bottom to select Foot Controls.

17.

NOT USED

864 Bobcat Loader Operation and Maintenance Manual

INSTRUMENT PANEL IDENTIFICATION (CONT’D)

TRACTION LOCK OVERRIDE

Cab Light

Figure OI-11

Figure OI-9

(Functions Only When The Seat Bar Is Raised And The Engine Is Running) There is a TRACTION LOCK OVERRIDE Button (Item 1) [Figure OI-11] on the left instrument panel which will allow you to use the steering levers to move the loader forward & b ackward when using the backhoe attachment or for loader service.

LIFT ARM BY-PASS CONTROL Figure OI-10

•

Press the TRACTION LOCK OVERRIDE Button once to unlock traction drive. The TRACTION light (Item 2) [Figure OI-11] will be ON.

•

Press the button a se cond time to lo ck the traction drive. The TRACTION light (Item 2) [Figure OI-11] will be OFF.

NOTE: The TRACTION LOCK OVERRIDE Button will unlock the traction drive when seat bar is raised and the engine is running.

The lift arm by-pass control (Item 1) [Figure OI-10] is used to lower the lift arms if the lift arms cannot be lowered during normal operations.

•

Sit in the operator's seat.

•

Fasten the seat belt and lower the seat bar.

•

Turn the knob (Item 1) [Figure OI-10] clockwise 1/4 turn.

•

Pull up and hold the knob until the lift arms slowly lower.

30 of 134

The TRACTION LOCK OVERRIDE Button will function if brake pedal is in the engaged or disengaged position and the engine is running.

OI-8

864 Bobcat Loader Operation and Maintenance Manual

Dealer Copy -- Not for Resale

Push the button (Item 1) [Figure OI-9] to turn the light ON. Push the button again to turn OFF.

PARKING BRAKE (LATER MODELS)

Figure OI-12

Figure OI-14

The speed control lever is at the right side of the operator's seat (Item 1) [Figure OI-12].

Press the top of the switch [Figure OI-14] to engage the parking brake. The traction drive system will be locked.

Move the lever forward to increase engine speed. Move backward to decrease engine speed.

Press the bottom of the switch [Figure OI-14] to disengage the parking brake. The traction drive system will be unlocked.

PARKING BRAKE (EARLY MODELS) NOTE: * The TRACTION light on the left instrument panel will remain OFF until the engine is started, the PRESS TO OPERATE LOADER Button is pressed and the parking brake is disengaged.

Figure OI-13

Push on the top of the pedal [Figure OI-13] to engage the parking brake. The traction drive system will be locked.

Push on the bottom of the pedal [Figure OI-13] to release the parking brake. The traction drive system will be unlocked.*

31 of 134

OI-9

864 Bobcat Loader Operation and Maintenance Manual

Dealer Copy -- Not for Resale

ENGINE SPEED CONTROL

STEERING LEVERS Figure OI-15

WARNING AVOID INJURY OR DEATH When operating the machine: • Keep the seat belt fastened snugly.

• The seat bar must be lowered.

• Keep your feet on the pedal controls or footrests and hands on steering levers.

W-2261-0799

The steering levers (Item 1) [Figure OI-15] are on the left and right side in front of the seat.

Move levers smoothly. Avoid sudden starting and stopping.

Figure OI-16

The steering levers control forward and reverse travel and turning the loader [Figure OI-16].

Reverse Travel - Pull both levers backward.

Normal Turning - M ove one lever farther forward than the other.

Fast Turning - Push one lever forward and pull the other lever backward.

For slow travel speed, push the s teering levers forward only a small amount.

To increase travel speed, push both levers farther forward.

For maximum pushing force, push the levers forward only a small amount with the engine at full speed.

STOPPING THE BOBCAT LOADER When the steering levers are moved to the neutral position, the hydrostatic transmission will act as a service brake to stop the loader.

32 of 134

OI-10

864 Bobcat Loader Operation and Maintenance Manual

Dealer Copy -- Not for Resale

Forward Travel - Push both levers forward.

When, the seat bar is up, the lift, tilt, and traction drive functions are deactivated and both foot pedals (if equipped) will be locked.

SEAT BAR RESTRAINT SYSTEM Figure OI-17

Before you leave the operator’s seat: • Lower the lift arms, put the attachment flat on the ground.

• Stop the engine.

• Engage the parking brake.

• Raise seat bar • (Foot Pedal Controls) Move pedals until both lock.

• (Advanced Hand Controls) Move the hand controls to the NEUTRAL POSITION to make sure that both lift and tilt functions are deactivated.

The seat bar system must deactivate the lift and tilt control functions when the seat bar is up.

Service the system if hand controls do not deactivate.

W-2327-0798

The seat bar restraint system has a pivoting seat bar with arm rests (Item 1) [Figure OI-17].

The operator controls the use of the seat bar. The seat bar in the down position helps to keep the operator in the seat.

WARNING AVOID INJURY OR DEATH When operating the machine: • Keep the seat belt fastened snugly.

• The seat bar must be lowered.

• Keep your feet on the pedal controls or footrests and hands on steering levers.

W-2261-0799

When the seat bar is down, PRESS TO OPERATE LOADER Button is a ctivated, and the brake pedal is released, the lift, tilt, and traction drive functions can be operated. (Traction drive will operate only when the engine is running.)

33 of 134

OI-11

864 Bobcat Loader Operation and Maintenance Manual

Dealer Copy -- Not for Resale

WARNING

Push the bottom (heel) (Item 2) [Figure OI-19] of the pedal to tilt the bucket backward.

HYDRAULIC CONTROLS Put your feet on th e pedals (or footrests) and KEEP THEM THERE any time you operate the loader.

Push the top (toe) (Item 3) [Figure OI-19] of the pedal to tilt the bucket forward.

Figure OI-18

Hand Controls (If Equipped)

3

Lift Arm Operation [Figure OI-18]

2 1

The left hand lever controls the lift arms.

B-15781

Move the left hand lever away from the operator (Item 4) [Figure OI-18] to raise the lift arms.

4 5 B-15672

6

Move the left hand lever toward the operator (Item 5) [Figure OI-18] to lower the lift arms.

B-15781

Figure OI-19 3

Move the left hand lever all the way toward the operator (Item 5) [Figure OI-18] until it locks into the float position.

B-15781

Later AHC & ACS Models With Float Button - To Engage: Press and hold the Float Button (Item 6) [Figure OI-18] while the lever is in neutral. Move the lever to the lift arm down position (Item 5) [Figure OI-18], then release the button.

- To Disengage: Press Float Button again or move the lever to the lift arm up position (Item 4) [Figure OI-18].

Use the float position of the lift arms to level loose material while driving backward.

2 1

4 5 B-15678

B-15973

Two foot pedals (or hand controls) (Item 1) [Figure OI18] and [Figure OI-19] control the hydraulic cylinders for the lift and tilt functions.

Move the l eft hand lever upward to unlock from the float position.

Foot Pedals Lift Arm Operation [Figure OI-18]

Tilt Operation [Figure OI-19]

The left pedal controls the lift arms.

Push on the bottom (heel) (Item 2) [Figure OI-18] of the pedal to raise the lift arms.

The right hand lever controls the bucket.

Push on the top (toe) (Item 3) [Figure OI-18] of the pedal to lower the lift arms.

Move the right hand lever toward the operator (Item 5) [Figure OI-19] to tilt the bucket backward.

Move the right hand lever away from the operator (Item 4) [Figure OI-19] to tilt the bucket forward.

Lift Arm Float Position [Figure OI-18] Push the top (toe) (Item 3) [Figure OI-18] of the pedal all the way forward until it locks into the float position.

WARNING

Use the float position of the lift arms to level loose material while driving backward.

Keep both feet on pedals while operating machine.

Failure to do so can cause serious injury.

Push the bottom of the left pedal to unlock from the float position.

W-2002-1285

Tilt Operation [Figure OI-19] The right pedal controls the bucket.

34 of 134

OI-12

864 Bobcat Loader Operation and Maintenance Manual

Dealer Copy -- Not for Resale

Lift Arm Float Position [Figure OI-18]

HYDRAULIC CONTROLS (CONT’D)

Figure OI-22

Quick Couplers Figure OI-20

Figure OI-21

To Disconnect: Rotate the ball release sleeve so that the grooves are aligned with the pins (Item 1) [Figure OI-22] in the female coupler.

Hold the male coupler. Retract the sleeve on the female coupler until the couplers disconnect.

NOTE: If the locking pins and grooves (Item 3) [Figure OI-22] are aligned, accidental disconnection is possible.

To Connect: Remove dirt or debris from the surface of both the male and female couplers, and from the outside diameter of the male coupler. Visually check the couplers for corroding, cracking, damage, or excessive wear. If any of these conditions exist, the coupler(s) must be r eplaced [Figure OI-20] and [Figure OI-21].

WARNING AVOID BURNS Hydraulic fluid, tubes, fittings and quick couplers can get hot when running machine and attachments.

Be careful when connecting and disconnecting quick couplers.

W-2220-0396

35 of 134

OI-13

864 Bobcat Loader Operation and Maintenance Manual

Dealer Copy -- Not for Resale

Install the male coupler into the female coupler. Full connection is made when the ball release sleeve slides forward on the female coupler and the sleeve is rotated so that the lo cking pins (Item 1) [Figure OI22] and the grooves (Item 2) [Figure OI-22] do NOT align (Locked Position).

HYDRAULIC CONTROLS (CONT’D)

Attachment Auxiliary Hydraulics (If Equipped) Auxiliary Hydraulics Button

Releasing Hydraulic Pressure (Loader and Attachment)

Figure OI-24

Loader: Figure OI-23

•

Press the AUXILIARY PRESSURE RELEASE Button (Item 1) [Figure OI-23]. Hold it for two seconds. The engine will stop and release hydraulic pressure.

Attachments: •

Follow procedure above to release pressure in loader.

•

Connect male coupler from attachment to female coupler of loader then repeat procedure above. This will release pressure in the attachment.

•

Connect the female coupler from the attachment.

Hydraulic pressure in the auxiliary hydraulic system can make it dif ficult to engage quick couplers to an attachment.

•

Variable Flow Variable Flow allows for slow-to-fast movement of auxiliary functions. If you move the auxiliary switch (Items 1) [Figure OI-25] half way, the auxiliary functions move at approximately one-half speed. Press the AUXILIARY HYDRAULICS Button (Item 1) [Figure OI-24] once. The light (Item 2) [Figure OI-24] will be ON.

•

Maximum Flow Only Maximum Flow allows for fast movement only. If you move the auxiliary switch (Items 1 or 3) [Figure OI-25], the auxiliary functions move at fast speed; release the switch to stop auxiliary functions.

Press the AUXILIARY HYDRAULICS Button (Item 1) [Figure OI-24] a second time. The light (Items 3) [Figure OI-24] will be ON.

•

Disengage Press the AUXILIARY HYDRAULICS Button (Item 1) [Figure OI-24] a third time. Both lights (Items 2 & 3) [Figure OI-24] will be OFF.

NOTE: When the operator is seated and raises the seat bar, the Auxiliary Hydraulic System (Front and Rear) will deactivate.

36 of 134

OI-14

864 Bobcat Loader Operation and Maintenance Manual

Dealer Copy -- Not for Resale

Figure OI-25

HYDRAULIC CONTROLS (CONT’D)

REAR Auxiliary Hydraulics Operation

FRONT Auxiliary Hydraulics Operation

(LEFT Steering Lever)

Figure OI-26

•

Press the AUXILIARY HYDRAULICS Button for Maximum Flow. (See Attachment Auxiliary Hydraulics (If Equipped) Auxiliary Hydraulics Button on Page OI14.)

Figure OI-27

(RIGHT Steering Lever)

• •

Press the AUXILIARY HYDRAULICS Button for Variable Flow (See above).

•

Push the switch (Item 1) [Figure OI-26] to the right or left to change the fluid flow direction to the front quick couplers. (EXAMPLE: Open and close grapple teeth.)

Push the switch (Item 3) [Figure OI-26] to the right or left to change the fluid flow direction to the rear quick couplers [Figure OI-27]. (EXAMPLE: Raise and lower rear stabilizers.)

Maximum Flow Only •

Press the AUXILIARY HYDRAULICS Button for Maximum Flow. (See Attachment Auxiliary Hydraulics (If Equipped) Auxiliary Hydraulics Button on Page OI14.)

Continuous Flow •

After selecting Variable or Maximum Flow, press the front switch (Item 2) [Figure OI-26] to give the front quick couplers a constant flow of fluid with the female coupler being pressurized. (EXAMPLE: Operate a backhoe.) To set reverse flow (male coupler pressurized), hold the auxiliary switch (Item 1) [Figure OI-26] to the left, press Variable or Maximum Flow and then press the front switch (Item 2) [Figure OI-26]. Reverse flow can be used only with augers, power rakes, sweepers, tillers, and vibratory rollers.

•

To release from continuous operation, press the front switch (Item 2) [Figure OI-26] a second time.

37 of 134

OI-15

864 Bobcat Loader Operation and Maintenance Manual

Dealer Copy -- Not for Resale

Variable Flow

HYDRAULIC CONTROLS (CONT’D)

Secondary Front Auxiliary Hydraulics (If Equipped)

High-Flow Hydraulics Operation (If Equipped)

Figure OI-30

The High-Flow function provides additional flow to th e system to operate an attachment which requires more hydraulic flow (EXAMPLE: Planer).

• •

•

If your loader has the HIGH FLOW Option, the secondary front auxiliary quick couplers are included (Item 1) [Figure OI-30]. (Also available separately as a Field Installed Accessory.) These are used when there is a need for additional auxiliary hydraulics (EXAMPLE: Planer side shift).

Connect the attachment to the quick couplers (Item 1) [Figure OI-28].

Some attachments may have a c ase drain which needs to be the connected to the small quick couplers (Item 2) [Figure OI-28].

Set the Auxiliary Hydraulics Button for Variable Flow or Maximum Flow Only. (See Attachment Auxiliary Hydraulics (If Equipped) Auxiliary Hydraulics Button on Page OI-14.)

•

Connect the atta chment to the secondary auxiliary hydraulics (Item 1) [Figure OI-30].

•

Set the Auxiliary Hydraulic Button for Variable Flow or Maximum Flow Only. (See Attachment Auxiliary Hydraulics (If Equipped) Auxiliary Hydraulics Button on Page OI-14.)

Figure OI-31

Figure OI-29

•

•

Press the HIGH FLOW Button (Item 1) [Figure OI29].

38 of 134

Push switch (Item 1) [Figure OI-31] to the right or left to change fluid flow direction. (EXAMPLE: Side shift on the Planer.)

NOTE: The secondary front auxiliary hydraulics and the rear auxiliary hydraulics operate from the same auxiliary section of the control valve. To operate only one of these auxiliary functions, disconnect the other.

OI-16

864 Bobcat Loader Operation and Maintenance Manual

Dealer Copy -- Not for Resale

Figure OI-28

HYDRAULIC CONTROLS (CONT’D)

Figure OI-34

Secondary Front Auxiliary Hydraulics (If Equipped) (Cont’d)

IMPORTANT If high-flow switch is in the ON position, High-Flow Hydraulics will flow through the front auxiliary quick coupler. Damage to unapproved attachments can result. Leave the switch OFF for backhoe operation.

I-2063-1197

Attachment Control Device (ACD) (If Equipped)

You can then use additional switches (Items 1 thr u 4) [Figure OI-34] on the r ight and left control handles for functions which control some attachments.

Figure OI-32

See the appropriate Attachment Maintenance Manual for control details.

Operation

&

WARNING Diesel fuel or hydraulic fluid under pressure can penetrate skin or eyes, causing serious injury or death. Fluid leaks under pressure may not be visible.

Use a piece of cardboard or wood to find leaks. Do not use your bare hand. Wear safety goggles. If fluid enters skin or eyes, get immediate medical attention from a physician familiar with this injury.

Figure OI-33

W-2072-0496

When this kit is installed (Item 1) [Figure OI-32], the ACD Icon light [Figure OI-33] on the right instrument panel will be ON when a 7- pin electric controlled attachment is installed.

You will need the Du al-Connector (7 pin/14 pin) Kit (Inset) [Figure OI-32] to operate early model attachments. See your Bobcat Loader dealer.

39 of 134

OI-17

864 Bobcat Loader Operation and Maintenance Manual

Dealer Copy -- Not for Resale

NOTE: When the Dual-Connector Kit is installed, the ACD Icon light [Figure OI-33], in the right instrument panel, will always be ON.

HYDRAULIC CONTROLS (CONT’D) Bucket Position Valve Operation (If Equipped) The function of the bucket position valve is to ke ep the bucket in the s ame approximate position it i s in before you begin raising the lift arms.

Dealer Copy -- Not for Resale

Figure OI-35

Press BUCKET POSITIONING Button (Item 1) [Figure OI-35] to eng age the bucket positioning function. (The light will be ON.) Press again to disengage.

Bucket Positioning functions only during the up ward lift cycle.

Shutdown Feature Press and hold the BUCKET POSITIONING Button (Item 1) [Figure OI-35] for 2 seconds. If the SHUTDOWN feature is installed, Shtdn will appear in the HOURMETER/CODE DISPLAY (Item 2) [Figure OI-35].

If it is not installed, BASE will appear. (Operational Code will also appear).

40 of 134

OI-18

864 Bobcat Loader Operation and Maintenance Manual

DAILY INSPECTION

Maintenance work must be done at regular intervals.

Failure to do so will result in excessive wear and early failures. The Service Schedule [Figure OI-36] is a guide for correct maintenance of the Bobcat Loader. It is located inside the rear door of the loader and also in the MACHINE SIGN TRANSLATION Section.

WARNING Operator must have instructions before operating the machine. Untrained operators can cause injury or death.

Daily Inspection and Maintenance • • • • • • • • • • • • • •

W-2001-0502

Engine Oil Level Hydraulic/Hydrostatic Fluid Level Engine Air Filter, Check Air System for Damage or Leaks Engine Coolant System, Check System for Damage or Leaks Operator Cab and Cab Mounting Hardware Seat Belt Seat Bar and Control Interlocks Grease Pivot Pins (Lift Arms, Bob-Tach, Cylinders, Bob-Tach Wedges) Tires, Check for Wear, Damage, Correct Air Pressure Fuel Filter, Remove Trapped Water Loose or Broken Parts, Repair or replace as necessary Safety Treads and Safety Signs (Decals), Replace as necessary Lift Arm Support Device. Replace if damaged Bobcat Interlock Control System (BICS)

41 of 134

NOTE: Fluids such as engine oil, hydraulic fluid, coolant, etc. must be disposed of in an environmentally safe manner.

Some regulations require that certain spills and leaks on the ground must be cleaned in a specific manner. See local, state and federal regulations for correct disposal.

OI-19

864 Bobcat Loader Operation and Maintenance Manual

Dealer Copy -- Not for Resale

Figure OI-36

PRE-STARTING PROCEDURE

Figure OI-38

Figure OI-37

Release the seat lever (Item 1) [Figure OI-38] and adjust the seat position for comfortable operation of the loader controls.

Use the bucket or attachment steps, grab handles and safety treads (on top of the loader lift arms and frame) to get on and off the loader [Figure OI-37]. Do not jump.

Figure OI-39

Dealer Copy -- Not for Resale

Safety treads are installed on the Bobcat Loader to provide a slip resistant surface for getting on and off the loader.

Keep safety treads clean and replace when damaged.

Replacement treads are available from your Bobcat Loader dealer.

Read and understand the O peration & Maintenance Manual and the Operator's Handbook (Item 1) [Figure OI-37] before operating the loader.

The Operation & Maintenance Manual and other manuals can be kept in a c ontainer (Item 2) [Figure OI37] provided behind the operator seat.

Suspension Seat (Option) Release the lever (Item 1) [Figure OI-39] to adjust the seat distance from the steering levers and foot pedals (if equipped). Release the lever (Item 2) [Figure OI39] to adjust the angle of the seat back. Turn the lever (Item 3) [Figure OI-39] to adjust the seat cushion for weight of the operator.

WARNING Instructions are necessary before operating or servicing machine. Read and understand the Operation & Maintenance Manual, Operator’s Handbook and signs (decals) on machine. Follow warnings and instructions in the manuals when making repairs, adjustments or servicing. Check for correct function after adjustments, repairs or service.

Untrained operators and failure to follow instructions can cause injury or death.

WARNING AVOID INJURY OR DEATH When operating the machine: • Keep the seat belt fastened snugly.

• The seat bar must be lowered.

• Keep your feet on the pedal controls or footrests and hands on steering levers.

W-2003-0903

W-2261-0799

42 of 134

OI-20

864 Bobcat Loader Operation and Maintenance Manual

PRE-STARTING PROCEDURE (CONT’D) Figure OI-40

IMPORTANT Check the seat belt and shoulder belt retractors for correct operation.

Keep retractors clean and replace as necessary.

I-2199-0200

Figure OI-42

Squeeze both seat belt adjusters to release and lengthen each half of the seat belt [Figure OI-40].

Pull the ends of the belt through the belt adjusters so that the seat belt is snug and the buckle is centered between your hips [Figure OI-40].

Figure OI-41

Lower the seat bar [Figure OI-42].

Engage the parking brake [Figure OI-42].

Figure OI-43

Put the fo ot pedals [Figure OI-43] (or hand controls) in neutral position.

3-Point Restraint (Option) Connect the shoulder belt to the lap belt (Item 1) [Figure OI-41]. Pull the lap belt across to the left side of the seat (Item 2) [Figure OI-41] and fasten.

The shoulder belt must be positioned over your right shoulder and the lap belt must be snug over your lower hips [Figure OI-41].

43 of 134

NOTE: Keep your hands on the steering levers and feet on the foot pedals (or footrests) while operating the loader [Figure OI-43].

OI-21

864 Bobcat Loader Operation and Maintenance Manual

Dealer Copy -- Not for Resale

Fasten the seat belt.

Turn the key switch to RUN [Figure OI-45]. The indicator lights on the right instrument panel [Figure OI-45] will come ON briefly and the Ins trument Panel / monitoring system will do a self test.

STARTING THE ENGINE Standard Instrument Panel (With Key Switch) Figure OI-44

If the tem perature is cold, the glow plugs will automatically cycle. The Glow Plug Icon light (Item 1) [Figure OI-45] will be ON and the cy cle time remaining will show in the hourmeter.

WARNING • •

AVOID INJURY OR DEATH Engines can have hot parts and hot exhaust gas.

Keep flammable material away.

Do not use machines in atmosphere containing explosive gas.

WARNING

When the Glow Plug Icon light goes OFF, turn the k ey switch to START [Figure OI-45].

When an engine is running in an enclosed area, fresh air must be added to avoid concentration of exhaust fumes. If the engine is stationary, vent the exhaust outside. Exhaust fumes contain odorless, invisible gases which can kill without warning.

Advanced Hand Controls (AHC) and Advanced Control System (ACS): Make sure both hand controls are in the neutral position before starting the engine. Do not move the Hand Control levers from the neutral position when turning the key to RUN or START [Figure OI-45].

W-2050-1285

If either hand control is moved:

Perform the PRE-STARTING PROCEDURE. (See PRESTARTING PROCEDURE on Page OI-20.)

a. The neutral position for the hydraulic valve spool and hand control may not be correctly calibrated. This can result in movement of the lift or tilt hydraulic cylinders when the hand control lever is returned to the neutral position after startup.

Set the engine speed control to the 1/2 speed position [Figure OI-44].

Figure OI-45

OR b. ACS (or AHC) (Item 2) [Figure OI-45] indicator light on right instrument panel will be ON. If either condition occurs, return key to STOP. Put the controls in neutral position and re-start the engine.

Release the key when the engine starts. It wi ll return to the RUN position.

(See Cold Temperature Starting on Page OI-24.)

44 of 134

OI-22

864 Bobcat Loader Operation and Maintenance Manual

Dealer Copy -- Not for Resale

W-2051-1086

STARTING THE ENGINE (CONT’D)

Figure OI-47

Deluxe Instrument Panel (With Keyless Start)

Use the numeric keypad (Item 1) [Figure OI-47] to enter the password, then press the RUN / ENTER Button (Item 2) [Figure OI-47].

WARNING When an engine is running in an enclosed area, fresh air must be added to avoid concentration of exhaust fumes. If the engine is stationary, vent the exhaust outside. Exhaust fumes contain odorless, invisible gases which can kill without warning.

If the tem perature is cold, the glow plugs will automatically cycle and the Glow Plug Icon light (Item 3) [Figure OI-47] will be ON.

W-2050-1285

When the Glow Plug Icon light goes OFF, press the START Button (Item 4) [Figure OI-47]. Release the button when the engine starts.

Advanced Hand Controls (AHC) and Advanced Control System (ACS): Make sure both hand controls are in neutral before starting the engine.

Do not move the Hand Control levers from the neutral position when pressing the RUN / ENTER Button (Item 2)[Figure OI-47].

WARNING • •

AVOID INJURY OR DEATH Engines can have hot parts and hot exhaust gas.

Keep flammable material away.

Do not use machines in atmosphere containing explosive gas.

If either hand control is moved: a. The neutral position for the hydraulic valve spool and hand control may not be correctly calibrated. This can result in movement of the lift or tilt hydraulic cylinders when the hand control lever is returned to the neutral position after startup.

W-2051-1086

Perform the PRE-STARTING PROCEDURE. (See PRESTARTING PROCEDURE on Page OI-20.)

OR

Set the engine speed control to the 1/2 speed position [Figure OI-46].

b. ACS (or AHC) indicator light (Item 5)[Figure OI47] on right instrument panel will be ON.

NOTE: Loaders with Deluxe Instrument Panel have a permanent, randomly generated Master Password set at the factory. Your loader will be assigned an Owner Password. Your dealer will provide you with this password. Change the password to one that you will easily remember to prevent unauthorized use of your loader. (See Passwords on Page SA-7.)

Keep your password in a safe place for future needs.

45 of 134

If either condition occurs, press the STOP Button (Item 6)[Figure OI-47]. Put the controls in neutral position and re-start the engine.

(See Cold Temperature Starting on Page OI-24.).

OI-23

864 Bobcat Loader Operation and Maintenance Manual

Dealer Copy -- Not for Resale

Figure OI-46

STARTING THE ENGINE (CONT’D)

Warming The Hydraulic/Hydrostatic System

Cold Temperature Starting If the temperature is below freezing, perform the following to make starting the engine easier: Replace the engine oil with the correct type and viscosity for the anticipated starting temperature.

•

Make sure the battery is fully charged.

•

Install an engine heater, available from your Bobcat Loader dealer.

When the temperature is below -20°F (-30°C), hydrostatic oil must be warmed before starting. The hydrostatic system will not get enough oil at low temperatures and will be damaged. Park the machine in an area where the temperature will be above 0°F (-18°C) if possible.

I-2007-1285

In cold conditions, it may take up to 60 seconds of cranking to reach the engine speed required to keep it running by itself. The cranking can continue only if you know that the engine is firing.

Let the engine run for a minimum of 5 minutes to warm the engine and hydrostatic transmission fluid before operating the loader.

Figure OI-48

Check the exhaust and listen to the sound of the engine.

If the engine is firing, there will be smoke from the exhaust and the cranking speed will continue to increase.

Dealer Copy -- Not for Resale

•

IMPORTANT

Do not continue to crank if the engine does not fire within the first 15 seconds of cranking. This extended cranking time must only be done if the engine speed is increasing because the engine is firing and aiding the starter.

NOTE: The LCD of the Deluxe Panel may not be immediately visible when the temperature is below -15°F (-26°C). It may take 30 seconds to several minutes for the Display Panel to warm up. All systems remain monitored even when the display is off.

Figure OI-49

If the Fluid Pressure Icon light (Item 1) [Figure OI-48] (Standard Panel) or [Figure OI-49] (Deluxe Panel) comes ON when operating the loader (cold), more warm up time is needed.

46 of 134

OI-24

864 Bobcat Loader Operation and Maintenance Manual

STOPPING THE ENGINE Figure OI-50

Pull the engine speed control fully backward [Figure OI50] to decrease the engine speed.

Dealer Copy -- Not for Resale

Turn the key switch to the STOP position [Figure OI-48] (Standard Panel) or press the STOP Button (Item 2) [Figure OI-49] (Deluxe Panel).

WARNING Do not use ether with glow plug (preheat) systems.

Explosion can result which can cause injury, death, or severe engine damage.

W-2071-0903

47 of 134

OI-25

864 Bobcat Loader Operation and Maintenance Manual

MONITORING THE DISPLAY PANEL

EXAMPLE: Engine Coolant Temperature is High.

Figure OI-51

Standard Panel The Engine Temperature Icon (Item 1) [Figure OI-51] will come ON. Press and hold the LIGHTS Button for 2 seconds and one of the fo llowing SERVICE CODES will be displayed in the hourmeter / code display: 08-10 Engine Coolant Temperature High or 08-11 Engine Coolant Temperature Very High Deluxe Panel

The SERVICE CODE will be in the hourmeter / code display (see above).

In addition, the Deluxe Panel display screen will describe the e xtreme condition that c an cause damage to the engine or loader systems [Figure OI52].

WARNING AND SHUTDOWN: When a WARNING condition exists, the associated Icon light will come ON and there will be 3 beeps from the alarm. Be aware that, if this condition is allowed to continue, there may be damage to the engine or loader hydraulic systems.

When a SHUTDOWN condition exists, the associated Icon light will come ON and there will be a c ontinuous beep from the alarm and the monitoring system will automatically stop the engine in 10 seconds. The engine can be restarted to move or relocate the loader.

The SHUTDOWN feature is included with the Deluxe Right Panel or a Factory Option with the Standard Panel.

The SHUTDOWN feature is associated with the following Icons: General Warning Engine Oil Pressure Engine Coolant Temperature Hydraulic Oil Temperature Hydrostatic Charge Pressure

After the engine is running, frequently monitor the right instrument panel [Figure OI-51] (Standard Panel) and [Figure OI-52] (Deluxe Panel) for error conditions.

Whenever STOP appears on the di splay screen, lower the lift arms all the way, put the attachment flat on the ground and stop the engine to prevent damage to the engine or loader systems.

The associated Icon will be O N if th ere is an er ror condition.

48 of 134

OI-26

864 Bobcat Loader Operation and Maintenance Manual

Dealer Copy -- Not for Resale

The Engine Temperature Icon (Item 1) [Figure OI-52] will be ON.

Figure OI-52

and avoiding machine damage, the a ttachment (or bucket) should handle a full load without going over the Rated Operating Capacity for the loader. Partial loads make steering more difficult.

ATTACHMENTS AND BUCKETS NOTE: Warranty is void if non-approved attachments are used on the Bobcat Loader.

Figure OI-54

WARNING

1

Never use attachments or buckets which are not approved by Bobcat Company. Buckets and attachments for safe loads of specified densities are approved for each model. Unapproved attachments can cause injury or death.

Load varies with model of pallet fork being used.

W-2052-0500

The dealer can identify, for each model loader, the attachments and buckets approved by Bobcat Company.

The buckets and attachments are approved for Rated Operating Capacity and for secure fastening to the BobTach.

The Rated Operating Capacity for this loader is shown on a decal in the operator cab. (See 864/864H COMPACT TRACK LOADER SPECIFICATIONS on Page SPEC-3.)

Maximum load to be ca rried when using a pallet fork is shown on a decal located on the pallet fork frame (Item 1) [Figure OI-54].

The Rated Operating Capacity is determined by using a standard dirt bucket, and material of normal density, such as dirt or dry gravel. If longer buckets are used, the load center moves forward and reduces the Rated Operating Capacity. If very dense material is loaded, the volume must be reduced to prevent overloading.

See your Bobcat dealer for more information about pallet fork inspection, maintenance and replacement. See your Bobcat Loader dealer for Rated Operating Capacity when using a pallet fork and for other available attachments.

Figure OI-53

WARNING AVOID INJURY OR DEATH Do not exceed Rated Operating Capacity (ROC).

Excessive load can cause tipping or loss of control.

W-2053-0903

Exceeding the Rated Operating Capacity [Figure OI-53] can cause the following problems: • Steering the loader may be difficult.

• Tires will wear faster.

• There will be a loss of stability.

• The life of the Bobcat Loader will be reduced.

Use the correct size bucket for the type and density of material being handled. For safe handling of materials 49 of 134

OI-27

864 Bobcat Loader Operation and Maintenance Manual

Dealer Copy -- Not for Resale

B-17255

ATTACHMENTS AND BUCKETS (CONT’D) Hand Lever Bob-Tach

WARNING

Installing The Bucket Or Attachment The Bob-Tach is used for fast changing of buc kets and attachments. See the appropriate Attachment Operation & Maintenance Manual to install other attachments.

Before you leave the operator’s seat: • Lower the lift arms, put the attachment flat on the ground.

• Stop the engine.

• Engage the parking brake.

• Raise seat bar • (Foot Pedal Controls) Move pedals until both lock.

• (Advanced Hand Controls) Move the hand controls to the NEUTRAL POSITION to make sure that both lift and tilt functions are deactivated.

The seat bar system must deactivate the lift and tilt control functions when the seat bar is up.

Service the system if hand controls do not deactivate.

Figure OI-55

W-2327-0798

Dealer Copy -- Not for Resale

Figure OI-57 Pull the Bob-Tach levers all the way up (Item 1) [Figure OI-55].

Enter the loader and perform the PRE-STARTING PROCEDURE. (See PRE-STARTING PROCEDURE on Page OI-20.)

Lower the lift arms and tilt the Bob-Tach forward.

Drive the loader forward until the top e dge of th e BobTach is completely under the top flange of the bucket [Figure OI-55] (or other attachment). Be sure the BobTach levers do not hit the bucket.

Figure OI-56 Push down on th e Bob-Tach levers until they are fully engaged in the locked position (Item 1) [Figure OI-57] (wedges fully extended).

Tilt the Bob-Tach backward until the cutting edge of the bucket (or other attachment) is slightly off the ground [Figure OI-56].

Stop the engine and exit the loader.

50 of 134

OI-28

864 Bobcat Loader Operation and Maintenance Manual

ATTACHMENTS AND BUCKETS (CONT’D)

WARNING

Hand Lever Bob-Tach (Cont’d) Figure OI-58

Before you leave the operator's seat: • Lower the lift arms, put the attachment flat on the ground.

• Stop the engine.

• Engage the parking brake.

• Raise seat bar.

• (Foot Pedal Controls) Move pedals until both lock.

• (Advanced Hand Controls) Move the hand controls to the NEUTRAL POSITION to make sure that both lift and tilt functions are deactivated.

The seat bar system must deactivate the lift and tilt control functions when the seat bar is up.

Service the system if hand controls do not deactivate.

W-2327-0798

The wedges (Item 1) [Figure OI-58] must extend through the holes (Item 2) [Figure OI-58] in the mounting frame of the bucket (or attachment), securely fastening the bucket to the Bob-Tach.

Dealer Copy -- Not for Resale

Figure OI-59

WARNING Bob-Tach wedges must extend through the holes in attachment. Lever(s) must be fully down and locked.

Failure to secure wedges can allow attachment to come off and cause injury or death.

W-2102-0497

Removing The Bucket Or Attachment Lower the l ift arms and put the attachment flat on th e ground and lower or close the hydraulic equipment.

Pull the Bob-Tach levers [Figure OI-59] all the way up.

•

Enter the loader.

If the attachment is hydraulically controlled (combination bucket, backhoe, etc.), stop the engine and relieve hydraulic pressure in the auxiliary circuit (See Releasing Hydraulic Pressure (Loader and Attachment) on Page OI-14.)

Perform the PRE-STARTING PROCEDURE. (See PRESTARTING PROCEDURE on Page OI-20.)

Start the engine.

Raise the seat bar, unfasten the seat belt, set the parking brake and exit the loader.

Release the parking brake.

Be sure the lift arms are all the way down. Tilt the BobTach forward.

WARNING Bob-Tach levers have spring tension. Hold lever tightly and release slowly. Failure to obey warning can cause injury.

W-2054-1285

51 of 134

OI-29

864 Bobcat Loader Operation and Maintenance Manual

ATTACHMENTS AND BUCKETS (CONT’D)

Power Bob-Tach

Hand Lever Bob-Tach (Cont’d)

Installing The Bucket Or Attachment

Figure OI-60

The Bob-Tach is used for fast changing of buckets and attachments. See the appropriate Attachment Operation & Maintenance Manual to install other attachments.

Perform the PRE-STARTING PROCEDURE. (See PRESTARTING PROCEDURE on Page OI-20.)

Lower the lift arms and tilt the Bob-Tach forward.

Figure OI-61

Dealer Copy -- Not for Resale

Move the loader backward, away from the bucket or attachment [Figure OI-60].

Push and hold BOB-TACH "WEDGES UP" switch (Front Accessory Panel) [Figure OI-61] until levers are in unlocked position (wedges fully raised).

52 of 134

OI-30

864 Bobcat Loader Operation and Maintenance Manual

ATTACHMENTS AND BUCKETS (CONT’D)

Removing The Bucket Or Attachment

Power Bob-Tach (Cont’d)

Lower the l ift arms and put the attachment flat on th e ground and lower or close the hydraulic equipment.

Installing The Bucket Or Attachment (Cont’d)

•

Figure OI-62

If the attachment is hydraulically (combination bucket, backhoe, etc.):

controlled

Stop the engine and relieve hydraulic pressure in the auxiliary circuit (See Releasing Hydraulic Pressure (Loader and Attachment) on Page OI-14.)

Exit the loader and disconnect the hydraulic hoses from the attachment.)

Enter the loader.

Perform the PRE-STARTING PROCEDURE. (See PRESTARTING PROCEDURE on Page OI-20.)

Start the engine.

Release the parking brake.

Drive the loader forward until the top e dge of th e BobTach is completely under the top flange of the bucket [Figure OI-62] (or other attachment).

Figure OI-63

Push and hold the BO B-TACH "WEDGES UP" Switch (Front Accessory Panel) [Figure OI-64] until the wedges are fully raised.

Tilt the Bob-Tach backward until the cutting edge of the bucket (or other attachment) is slightly off the ground [Figure OI-63].

Tilt the Bob-Tach forward.

Push and hold BOB-TACH "WEDGES DOWN" switch (Front Accessory Panel) [Figure OI-61] until the wedges are fully extended through the mounting frame holes (Item 1) [Figure OI-61].

Figure OI-65

Check that both Bob-Tach levers are fully down and in the locked position, and that both wedges are through the mounting frame holes [Figure OI-61].

WARNING Bob-Tach wedges must extend through the holes in attachment. Lever(s) must be fully down and locked.

Failure to secure wedges can allow attachment to come off and cause injury or death.

Move the loader backward, away from the bucket or attachment [Figure OI-65].

W-2102-0497

53 of 134

OI-31

864 Bobcat Loader Operation and Maintenance Manual

Dealer Copy -- Not for Resale

Figure OI-64

OPERATING PROCEDURES

Figure OI-67

When operating on a public road or highway, always follow local regulations. For example: Slow Moving Vehicle Sign or direction signals may be required.

Always warm the engine and hydrostatic system before operating the loader.

IMPORTANT Machines warmed up with moderate engine speed and light load have longer life.

I-2015-0284

With a full bucket, go up or down the slope with the heavy end toward the top of the slope [Figure OI-66] & [Figure OI-67].

Operate the loader with the en gine at ful l speed for maximum horsepower. Move the st eering levers only a small amount to operate the loader slowly.

Figure OI-68

Dealer Copy -- Not for Resale

New operators must operate the loader in an open area without bystanders. Operate the controls until the loader can be handled at an efficient and safe rate for all conditions of the work area.

Figure OI-66

Figure OI-69

With empty bucket, go down or up the slope with the heavy end toward the top of the slope [Figure OI-68] & [Figure OI-69].

54 of 134

OI-32

864 Bobcat Loader Operation and Maintenance Manual

OPERATING PROCEDURE (CONT’D)

Figure OI-71

WARNING AVOID INJURY OR DEATH • Keep the lift arms as low as possible.

• Do not travel or turn with the lift arms up.

• Turn on level ground.

• Go up and down slopes, not across them.

• Keep the heavy end of the machine uphill.

• Do not overload the machine.

Failure to obey warnings can cause the machine to tip or roll over and cause injury or death.

W-2018-1187

Compact Track Loader Operating Tips

Go directly up or down a slope, not across the slope to prevent tracks from derailing.

Correct track tension is important. If the tracks are too loose, they can easily derail. If they are too tight, they will wear faster and cause increased stress on the complete track carriage system.

Figure OI-72

Figure OI-70

Avoid operating the loader with one track on a slope and the other on flat ground [Figure OI-72] or with the edge of the track turned up a gainst a cu rb or mound [Figure OI-72]. This can cause the tracks to derail, cracks in the edge of the tr acks or cracks at the edges of the embedded metal.

Use a gr adual turn (one lever farther forward than the other) instead of a fast turn (one steering lever forward, one backward) on asphalt or concrete surfaces to prevent reduced track life or derailing of tracks [Figure OI-70].

55 of 134

Avoid operating or turning on s harp objects such as jagged rocks or broken concrete. This can cause cuts on the lug surface of the tracks [Figure OI-72].

OI-33

864 Bobcat Loader Operation and Maintenance Manual

Dealer Copy -- Not for Resale

Keep the ful l length of the tracks in contact with the ground [Figure OI-71] for best traction. Raising the front end of the tracks off the ground [Figure OI-71] will reduce traction and cause increased track wear.

Raise the bucket only high enough to avoid obstructions on rough ground.

OPERATING PROCEDURE (CONT’D)

Figure OI-75

Compact Track Loader Operating Tips (Cont’d) Figure OI-73

Drive slowly forward into the material. Push the bottom of the tilt pedal (Item 1) [Figure OI-75] to raise the front of the bucket.

Figure OI-74

Drive backward away from the material.

WARNING Load, unload and turn on flat level ground. Do not exceed Rated Operating Capacity (ROC) shown on sign (decal) in cab. Failure to obey warnings can cause the machine to tip or roll over and cause injury or death.

W-2056-0903

Filling the Bucket (Hand Controls) Move the left hand lever, from neutral position (N), toward the operator (Item 3) [Figure OI-74] until the lift arms are all the way down.

Push the top of the lift pedal (Item 1) [Figure OI-74] until the lift arms are all the way down.

Move the right hand lever, from neutral position (N) away from the operator (Item 4) [Figure OI-74] to put the cutting edge of the bucket on the ground.

Push the top of the tilt pedal (Item 2) [Figure OI-74] to put the cutting edge of the bucket on the ground.

Drive slowly forward into the material. Move the right hand lever, from neutral position (N), toward the operator (Item 2) [Figure OI-75] to raise the front of the bucket.

Drive backward away from the material.

56 of 134

OI-34

864 Bobcat Loader Operation and Maintenance Manual

Dealer Copy -- Not for Resale

Filling the Bucket (Foot Pedals)

OPERATING PROCEDURE (CONT’D)

Leveling the Ground (Using Lift Arms in Float Position) (Foot Pedals)

Emptying the Bucket (Foot Pedals) Figure OI-77

Push the top of the lift pedal (Item 1) [Figure OI-77] all the way forward until the pedal is in the locked position to put the lift arms in the float position.

Push the bottom of the lift pedal (Item 1) [Figure OI76] to raise the lift arms. Push the top of the tilt pedal while raising the lift arms to le vel the buc ket or attachment and help prevent material from falling off the back of the bucket or attachment.

Push the tilt pedal (Item 2) [Figure OI-77] to change the position of the cutting edge on the bucket.

Drive forward slowly until the bucket is over the top of the truck box or bin.

With the bucket tilted farther forward, there is more force on the cutting edge and more loose material can be moved.

Push the top of the tilt pedal (Item 2) [Figure OI-76] until the bucket is empty. If all the material is near the side of the truck or bin, push it to the other side with the bucket.

Drive backward to level loose material.

Push the bottom of the li ft pedal to unl ock from the float position.

Emptying the Bucket (Hand Controls) Move the left hand lever, from neutral position (N), away from the o perator (Item 3) [Figure OI-76] to raise the lift arms. Move the right hand lever, from neutral position (N), away from the operator to level the bucket or attachment and help prevent material from falling off the back of the bucket or attachment.

Drive forward slowly until the bucket is over the top of the truck box or bin.

Move the right hand lever, from neutral position (N), away from the operator (Item 4) [Figure OI-76] until the bucket is empty. If all the material is near the side of the truck or bin, push it to the other side with the bucket.

57 of 134

OI-35

864 Bobcat Loader Operation and Maintenance Manual

Dealer Copy -- Not for Resale

Figure OI-76

OPERATING PROCEDURE (CONT’D)

Digging Into the Ground (Foot Pedals) Put the lift arms all the way down. Push the top of the tilt pedal (Item 1) [Figure OI-78] until the cutting edge of the bucket is on the ground.

Leveling the Ground (Using Lift Arms in Float Position) (Hand Controls) Move the left hand lever, from neutral position (N), all the way down and in (Item 3) [Figure OI-77] until the hand lever is in the locked position to put the lift arms in the float position.

Figure OI-78

- To Engage: Press and hold the Float Button (Item 6) [Figure OI-76] while the lever is in neutral. Move the lever to the lift arm down position (Item 5) [Figure OI-76], then release the button.

- To Disengage: Press Float Button again or move the lever to the lift arm up position (Item 4) [Figure OI-76].

With the bucket tilted farther forward, there is more force on the cutting edge and more loose material can be moved.

Drive forward slowly and continue to til t the bucket down (Item 1) [Figure OI-78] until it enters the ground.

Drive backward to level loose material.

Move the left hand lever upward to unlock from the float position.

Push the b ottom of t he tilt pedal a s mall amount to increase traction and keep an even digging depth.

Continue to drive forward until the bucket is full. When the ground is hard, raise and lower the cutting edge of the bucket with the tilt pedal while driving forward slowly.

WARNING

Figure OI-79 Never dump over an obstruction, such as a post, that can enter the operator cab. The machine could tip forward and cause injury or death.

W-2057-0694

IMPORTANT Never drive forward when the hydraulic control for lift arms is in float position.

I-2005-1285

Push the bottom of the tilt pedal (Item 1) [Figure OI79] to tilt the bucket backward as far as it will go when the bucket is full.

58 of 134

OI-36

864 Bobcat Loader Operation and Maintenance Manual

Dealer Copy -- Not for Resale

Move the right hand lever, from neutral position (N), away from the operator (Item 4) [Figure OI-77], to change the position of the cutting edge on the bucket.

OPERATING PROCEDURE (CONT’D)

Backfilling (Foot Pedals)

Digging Into the Ground (Hand Controls)

Figure OI-80

Put the lift arms all the way down. Move the right hand lever away from the operator (Item 2) [Figure OI-78] until the cutting edge of the bucket is on the ground.

Drive forward slowly and continue to tilt the bucket down until it enters the ground.

Move the right hand lever toward the operator a small amount to increase traction and keep an even digging depth. Continue to drive forward until the bu cket is full. When the ground is hard, raise and lower the cutting edge of the bucket with the hand lever while driving forward slowly.

Lower the lift arms (Item 1) [Figure OI-80] and put the cutting edge of the bucket on the ground. Drive forward to the edge of the hole to push the material into the hole.

Tilt the bucket forward (Item 2) [Figure OI-80] as soon as it is past the edge of the hole.

If necessary, raise the lift arms to empty the bucket.

Backfilling (Hand Controls) Lower the lift arms (Item 3) [Figure OI-80] and put the cutting edge of the bucket on the ground. Drive forward to the edge of the hole to push the material into the hole.

Tilt the bucket forward (Item 4) [Figure OI-80] as soon as it is past the edge of the hole.

If necessary, raise the lift arms to empty the bucket.

59 of 134

OI-37

864 Bobcat Loader Operation and Maintenance Manual

Dealer Copy -- Not for Resale

Move the right hand lever toward the operator (Item 2) [Figure OI-79] to tilt the bucket backwards as far as it will go when the bucket is full.

TRANSPORTING THE BOBCAT LOADER

Figure OI-82

WARNING Adequately designed ramps of sufficient strength are needed to support the weight of the machine when loading onto a transport vehicle. Wood ramps can break and cause personal injury.

P-13808

P-13807

W-2058-0494

P-24480b 6718401

Always drive backward onto the transport vehicle [Figure OI-81] when the loader has an empty bucket or no attachment.

Fasten the Bobcat Loader to the t ransport vehicle to prevent the l oader from moving during sudden stops or when going up or down slopes [Figure OI-82].

The rear of the tr ailer must be blocked or supported [Figure OI-81] when loading or unloading the l oader to prevent the front end of the trailer from raising up.

Be sure the transport and towing vehicles are of adequate size and capacity. (See 864/864H COMPACT TRACK LOADER SPECIFICATIONS on Page SPEC-3.)

60 of 134

N-18275

OI-38

•

Lower the bucket or attachment to the floor.

•

Stop the engine and engage the parking brake.

•

Install chains at the front and rear loader tie down positions (inset) [Figure OI-82].

•

Fasten each end of th e chain diagonally to th e transport vehicle.

•

Install load binders to tighten the chains.

864 Bobcat Loader Operation and Maintenance Manual

Dealer Copy -- Not for Resale

Figure OI-81

TOWING THE LOADER

Figure OI-84

WARNING Never work on a machine with the lift arms up unless the lift arms are secured by an approved lift arm support device. Failure to use an approved lift arm support device can allow the lift arms or attachment to fall and cause injury or death.

W-2059-0598

Tow the loader only a short distance at slow speed.

(Example: Moving the loader onto a transport vehicle).

- Connect a Port-a-Power to the quick coupler located near the brake block (Item 1) [Figure OI-84].

The towing chain (or cable) must be rated at 1 & 1/ 2 times the wei ght of the l oader. (See 864/864H COMPACT TRACK LOADER SPECIFICATIONS on Page SPEC-3.)

The hydraulic brakes must be disengaged to allow towing of the loader.

•

- Lower the cab and tow the loader.

- Before operating the loader again, disconnect the Port-a-Power and engage the parking brake solenoid valve, by pushing IN on the red Traction Lock ByPass Knob (Item 1) [Figure OI-83] and turning it 1/4 TURN clockwise.

Raise the cab. (See Raising The Operator Cab on Page PM-10.)

Figure OI-83

- Disengage the parking brake solenoid valve by pushing IN on the red Traction Lock By-Pass Knob (Item 1) [Figure OI-83] and turning it 1/4 T URN counterclockwise. The knob will come out to release the solenoid valve.

61 of 134

OI-39

864 Bobcat Loader Operation and Maintenance Manual

Dealer Copy -- Not for Resale

- Operate the Port-a-Power to 400 PSI (2758 kPa) to release the brake.

LIFTING THE LOADER

Single Point Lift

Four Point Lift

WARNING WARNING AVOID INJURY OR DEATH Before lifting, check fasteners on four point lift.

Never allow riders in the cab or bystanders within 15 ft. (5 m) while lifting the machine.

• •

W-2160-0694

AVOID INJURY OR DEATH Before lifting, check fasteners on single point lift and operator cab.

Assemble front cab fasteners as shown in this manual.

Never allow riders in the cab or bystanders within 15 feet (5 meters) while lifting the machine.

W-2007-0497

Lift the loader with the four point lift which is available as a kit from your Bobcat Loader dealer.

Lift the loader with the single point lift which is available as a kit from your Bobcat Loader dealer.

Figure OI-85

Figure OI-86

Attach cables or chains to th e four lift points as shown [Figure OI-85].

Attach cables or chains to the single point lift as shown [Figure OI-86].

The single point lift, supplied by Bobcat Company is designed to l ift and support the Bobcat Loader without affecting roll over and falling object protection features of the operator cab.

62 of 134

OI-40

864 Bobcat Loader Operation and Maintenance Manual

Dealer Copy -- Not for Resale

• •

•

PREVENTIVE MAINTENANCE AIR CLEANER SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PM-20 Replacing Filter Element . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PM-20 ALTERNATOR BELT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PM-37 Adjusting The Alternator Belt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PM-37 BOBCAT INTERLOCK CONTROL SYSTEM (BICS) . . . . . . . . . . . . . . . PM-15 Additional Inspection For Loaders With Advanced Hand Controls (AHC) and Advanced Control System (ACS). . . . . . . . . . . . . . . . . . . . . . . . . . . . PM-16 Inspecting Deactivation Of The Auxiliary Hydraulics System (Engine STOPPED - Key ON). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PM-15 Inspecting The BICS Controller (Engine STOPPED - Key ON). . . . . PM-15 Inspecting The Lift Arm By-Pass Control . . . . . . . . . . . . . . . . . . . . . . PM-15 Inspecting The Seat Bar Sensor (Engine RUNNING) . . . . . . . . . . . . PM-15 Inspecting The Traction Lock (Engine RUNNING) . . . . . . . . . . . . . . PM-15

PREVENTIVE MAINTENANCE

DRIVE BELT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PM-36 Adjusting The Drive Belt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PM-36 Replacing The Drive Belt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PM-36 ELECTRICAL SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PM-27 Cleaning Battery And Terminals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . PM-27 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PM-27 Fuse Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PM-27 Removing And Installing The Battery. . . . . . . . . . . . . . . . . . . . . . . . . PM-29 Using A Booster Battery (Jump Starting) . . . . . . . . . . . . . . . . . . . . . . PM-28 ENGINE COOLING SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PM-26 Cleaning The Cooling System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PM-26 ENGINE LUBRICATION SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PM-25 Checking Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PM-25 Replacing The Oil And Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PM-25 FAN GEARBOX. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PM-35 Checking And Maintaining . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PM-35 FUEL SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PM-22 Filling The Fuel Tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PM-22 Fuel Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PM-22 Fuel Lift Pump Strainer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PM-23 Fuel Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PM-22 Removing Air From The Fuel System . . . . . . . . . . . . . . . . . . . . . . . . PM-23 Removing Fuel From The Fuel Tank . . . . . . . . . . . . . . . . . . . . . . . . . PM-24 Continued On Next Page

PM-1 63 of 134

864 Bobcat Loader Operation & Maintenance Manual

Dealer Copy -- Not for Resale

BOB-TACH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PM-41 Inspection And Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PM-41

PREVENTIVE MAINTENANCE (CONT’D) HEATER AND AIR CONDITIONING . . . . . . . . . . . . . . . . . . . . . . . . . . PM-40 Cleaning and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PM-40 HYDRAULIC/HYDROSTATIC SYSTEM . . . . . . . . . . . . . . . . . . . . . . . PM-31 Checking And Adding Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PM-31 Replacing Hydraulic/Hydrostatic Filter . . . . . . . . . . . . . . . . . . . . . . PM-31 Replacing The Hydraulic Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . PM-32 HYDROSTATIC MOTOR CARRIER OIL. . . . . . . . . . . . . . . . . . . . . . . PM-34 Hydraulic Reservoir Breather Cap . . . . . . . . . . . . . . . . . . . . . . . . . PM-33 Removing And Replacing Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PM-34 LIFT ARM SUPPORT DEVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PM-8 Disengaging The Lift Arm Support Device . . . . . . . . . . . . . . . . . . . . PM-9 Engaging The Lift Arm Support Device . . . . . . . . . . . . . . . . . . . . . . PM-8

MAINTENANCE SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PM-5 OPERATOR CAB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PM-10 Emergency Exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .PM-11 Lowering the Operator Cab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .PM-11 Raising The Operator Cab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PM-10 PIVOT PINS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PM-19 POWER BOB-TACH (OPTION) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PM-42 Inspection And Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PM-42 REAR DOOR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PM-18 Adjusting The Rear Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PM-18 Opening And Closing The Rear Door . . . . . . . . . . . . . . . . . . . . . . PM-18 REAR GRILL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PM-19 SERVICE SCHEDULE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PM-7 SEAT BAR RESTRAINT SYSTEM ADVANCED HAND CONTROLS (AHC) AND ADVANCED CONTROL SYSTEM (ACS) . . . . . . . . . . . . . . . . . . . . . . PM-14 Inspecting The Seat Bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PM-14 Maintaining The Seat Bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PM-14 SEAT BAR RESTRAINT SYSTEM (FOOT PEDALS) . . . . . . . . . . . . . PM-13 Inspecting The Seat Bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PM-13 Maintaining The Seat Bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PM-13 Continued On Next Page

PM-2 64 of 134

864 Bobcat Loader Operation & Maintenance Manual

Dealer Copy -- Not for Resale

LUBRICATION OF THE BOBCAT LOADER . . . . . . . . . . . . . . . . . . . . PM-38

PREVENTIVE MAINTENANCE (CONT’D) TIMING BELT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PM-37 TRACK ROLLER AND IDLER LUBRICATION . . . . . . . . . . . . . . . . . . . . PM-34 Removing And Replacing Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PM-34

Dealer Copy -- Not for Resale

TRACK TENSION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PM-16 Adjusting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PM-17

PM-3 65 of 134

864 Bobcat Loader Operation & Maintenance Manual

Dealer Copy -- Not for Resale PM-4 66 of 134

864 Bobcat Loader Operation & Maintenance Manual

MAINTENANCE SAFETY WARNING

Instructions are necessary before operating or servicing machine. Read and understand the Operation & Maintenance Manual, Operator’s Handbook and signs (decals) on machine. Follow warnings and instructions in the manuals when making repairs, adjustments or servicing. Check for correct function after adjustments, repairs or service. Untrained operators and failure to follow W-2003-0903 instructions can cause injury or death.

CORRECT

CORRECT

CORRECT

B-10731a

B-15659

B-15660

Use the correct procedure to lift or lower operator cab.

Cleaning and maintenance are required daily.

WRONG

WRONG

WRONG

B-15664

B-15661

B-15662

Have good ventilation when welding or grinding painted parts.

Wear dust mask when grinding painted parts. Toxic dust and gas can be produced.

Avoid exhaust fume leaks which can kill without warning. Exhaust system must be tightly sealed.

Disconnecting or loosening any hydraulic tubeline, hose, fitting, component or a part failure can cause lift arms to drop. Do not go under lift arms when raised unless supported by an approved lift arm support device.

Replace it if damaged.

Never work on loader with lift arms up unless lift arms are held by an approved lift arm support device. Replace if damaged.

Never modify equipment or add attachments not approved by Bobcat Company.

WRONG

WRONG

WRONG

B-15665

B-15663

B-6589

Stop, cool and clean engine of flammable materials before checking fluids.

Never service or adjust loader with the engine running unless instructed to do so in the manual.

Avoid contact with leaking hydraulic fluid or diesel fuel under pressure. It can penetrate the skin or eyes.

Never fill fuel tank with engine running, while smoking or when near open flame.

Keep body, jewelry and clothing away from moving parts, electrical contact, hot parts and exhaust.

Wear eye protection to guard from battery acid, compressed springs, fluids under pressure and flying debris when engines are running or tools are used.

Use eye protection approved for type of welding.

Keep rear door closed except for service. Close and latch door before operating the loader.

Never service the Bobcat Compact Track Loader without instructions.

Lead-acid batteries produce flammable and explosive gases.

Keep arcs, sparks, flames and lighted tobacco away from batteries.

Batteries contain acid which burns eyes or skin on contact.

Wear protective clothing. If acid contacts body, flush well with water. For eye contact flush well and get immediate medical attention.

Maintenance procedures which are given in t he Operation & M aintenance Manual can be p erformed by the ow ner/ operator without any specific technical training. Maintenance procedures which are not in the Operation & Maintenance Manual must be performed ONLY BY QUALIFIED BOBCAT SERVICE PERSONNEL. Always use genuine Bobcat replacement parts. The Service Safety Training Course is available from your Bobcat dealer.

MSW09-0805

67 of 134

PM-5

864 Bobcat Loader Operation and Maintenance Manual

Dealer Copy -- Not for Resale

Safety Alert Symbol: This symbol with a warning statement, means: “Warning, be alert! Your safety is involved!” Carefully read the message that follows.

Dealer Copy -- Not for Resale 68 of 134

PM-6

864 Bobcat Loader Operation and Maintenance Manual

SERVICE SCHEDULE Maintenance work must be done at regular intervals. Failure to do so will result in excessive wear and early failures. The service schedule is a guide for correct maintenance of the Bobcat Loader.

WARNING

Instructions are necessary before operating or servicing machine. Read and understand the Operation & Maintenance Manual, Operator’s Handbook and signs (decals) on machine. Follow warnings and instructions in the manuals when making repairs, adjustments or servicing. Check for correct function after adjustments, repairs or service. Untrained operators and failure to follow instructions can cause injury or death.

W-2003-0903

SERVICE SCHEDULE ITEM

HOURS

SERVICE REQUIRED

8-10 50

Engine Oil

Check the oil level and add oil as needed.

Engine Air Filter and Air System

Check condition indicator or display panel. Service only when required. Check for leaks and damaged components.

Engine Cooling System

Clean debris from oil cooler radiator & grill.

250 500 1000 3000

Lift Arms, Cyl. Bob-Tach Pivot Pins Lubricate with multi-purpose lithium based grease (12 places). and Wedges Seat Belt, Seat Bar and Pedal Check the condition of seat belt. Check the seat bar, and foot pedal interlocks Interlocks for correct operation. Clean dirt and debris from moving parts.

Bobcat Interlock Control System (BICS™) Check BICS functions.

Check for damaged signs (decals) and safety treads. Replace any signs or safety treads that are damaged or worn.

Operator Cab

Check the fastening bolts, washers and nuts. Check the condition of cab.

Fuel Filter

Remove the trapped water.

Tracks

‡ Check for damaged tracks and correct tension.

Hyd. Fluid, Hoses & Tubelines

Check fluid level and add as needed. Check for damage and leaks. Repair and replace as needed.

Battery

Check cables connections and electrolyte level. Add distilled water as needed.

Foot Pedals or Hand Controls & Steering

Check for correct operation. Repair or adjust as needed.

Parking Brake

Check operation of the brake.

Alternator Belt

Check tension and adjust as needed.

Engine/Hydro. Drive Belt

* Check for wear or damage. Check idler arm stop.

Fuel Filter

Replace filter element.

Fuel Strainer

Clean the fuel strainer screen.

Steering Shaft

Grease three fittings.

Hyd. Reservoir Breather Cap

Replace the reservoir breather cap.

Hyd./Hydro. Filter

zReplace the filter element.

Engine Oil and Filter

† Replace oil & filter. Use CD or better grade oil and Bobcat filter.

Hydrostatic Motor Carrier

Replace oil. Use Synthetic Oil 6682546.

Hydraulic Reservoir

Clean or replace the fluid.

Hydrostatic Motors

Clean or replace the case drain filters.

Bobcat Interlock Control System (BICS)

Check lift arm by-pass control.

Fan Drive Gearbox

Check gear lubrication level.

Engine Valves

∞ Adjust the engine valves.

Track Rollers and Idlers

Replace oil. Use SAE 10W-40. (Rollers and Idlers - 100cc)

Engine Timing Belt

Replace the timing belt and belt tensioner assy.

Dealer Copy -- Not for Resale

Safety Signs and Safety Treads

❍

l Also replace hydraulic/hydrostatic filter element when the transmission warning light comes ON. n Or every 12 months. * Inspect the new belt after first 50 hours. † First oil and filter change must occur at 50 hours; 500 hours thereafter. m Engine Oil and Filter must be changed at 250 hours when used in extreme duty applications.

• After the first 500 hours on new engine, adjust engine valves; 1000 hours thereafter. (See Service Manual for procedure.) ‡ Check every 8-10 hours for the first 50 hours. Then at 50 hour intervals. uOr every 5 years. ‡ Check every 8-10 hours for the first 50 hours. Then at 50 hour intervals.

69 of 134

PM-7

864 Bobcat Loader Operation and Maintenance Manual

LIFT ARM SUPPORT DEVICE

Figure PM-2

Maintenance and service work can be do ne with the lift arms lowered. If the lift arms are raised, use the following procedures to en gage and disengage an ap proved lift arm support device:

WARNING Never work on a machine with the lift arms up unless the lift arms are secured by an approved lift arm support device. Failure to use an approved lift arm support device can allow the lift arms or attachment to fall and cause injury or death.

W-2059-0598

WARNING

With the operator in the seat, seat belt fastened and seat bar lowered, start the engine.

Service lift arm support device if damaged or if parts are missing. Using a damaged lift arm support or with missing parts can cause lift arms to drop causing injury or death.

Figure PM-3

W-2271-1197

Engaging The Lift Arm Support Device Figure PM-1

Raise the lift arms, until the lift arm support device drops onto the lift cylinder rod (Inset) [Figure PM-3].

Lower the lift arms slowly until the support device is held between the lift arm and the lift cylinder. Stop the engine.

Raise the s eat bar and move pedals (if equipped) until both pedals lock.

Install jackstands under the rear of t he loader frame (Inset) [Figure PM-1].Disconnect the spring from the li ft arm support device retaining pin (Item 1) [Figure PM-1].

Support the lift arm support device (Item 2) [Figure PM1] with your hand and remove the retaining pin.

70 of 134

PM-8

864 Bobcat Loader Operation and Maintenance Manual

Dealer Copy -- Not for Resale

Lower the lift arm support device on top of the lift cylinder.

Hook the free end of the spring (Item 1) [Figure PM-2] to the lift arm support device so there will be no interference with the support device engagement.

Disengaging The Lift Arm Support Device

Engaging The Lift Arm Support Device (Cont’d)

Remove the pin from the lift arm support device.

Figure PM-4

Figure PM-5

Install pin (Item 1) [Figure PM-4] into the rear of the lift arm support device below the cylinder rod.

Connect the spring (Item 1) [Figure PM-5] from the li ft arm support device to the bracket below the lift arms.

With the operator in the seat, seat belt fastened and seat bar lowered, start the engine.

Raise the lift arms a small amount. The spring will lift the support device off the l ift cylinder rod (Item 2) [Figure PM-5]. Lower the lift arms. Stop the engine.

Raise the s eat bar and move pedals (if equipped) until both pedals lock.

Disconnect the spring from the bracket.

Figure PM-6

Raise the support device into storage position and insert pin (Item 1) [Figure PM-6] through lift arm support device and bracket.

Connect spring to pin (Item 2) [Figure PM-6].

71 of 134

PM-9

864 Bobcat Loader Operation and Maintenance Manual

Dealer Copy -- Not for Resale

LIFT ARM SUPPORT DEVICE (CONT’D)

OPERATOR CAB

Figure PM-8

The Bobcat Loader has an operator cab (ROPS and FOPS) as standard equipment to protect the operator from rollover and falling objects. Check with your dealer if the operator cab has been damaged.

ROPS/FOPS - Roll Over Protective Structure per SAE J1040 and ISO 3471, and Falling Object Protective Structure per SAE J1043 and ISO 3449, Level l. Level ll is available.

Level l - Protection from falling bricks, small concrete blocks and hand tools encountered in operations such as highway maintenance, landscaping, and oth er construction site services.

Remove the nut and plate at the front corner of the cab (both sides) [Figure PM-8].

Level ll - Protection from falling trees, rocks; for machines involved in site clearing, overhead demolition or forestry.

Stop the loader on a level surface, lower the lift arms and stop the engine.

Advanced Hand Controls (AHC) and Advanced Control System (ACS)

If the lift arms must be up while raising the cab, install an approved lift arm support device. (See Engaging The Lift Arm Support Device on Page PM-8.)

Figure PM-7

Put Jackstands under the rear of the loader frame (Inset) [Figure PM-7].

WARNING

WARNING

Never modify operator cab by welding, grinding, drilling holes or adding attachments unless instructed to do so by Bobcat Company. Changes to the cab can cause loss of operator protection from rollover and falling objects, and result in injury or death.

Before the cab or the lift arms are raised for service, jackstands must be put under the rear corners of the frame. Failure to use jackstands can allow the machine to tip backward causing injury or death.

W-2014-0895

72 of 134

W-2069-0200

PM-10

864 Bobcat Loader Operation and Maintenance Manual

Dealer Copy -- Not for Resale

Lift on the grab handle and bottom of the cab slowly until the cab latching mechanism engages and the cab is all the way up [Figure PM-7] and the la tching mechanism engages.

Raising The Operator Cab

Tighten the nuts to 40-50 ft.-lb. (54-68 N•m) torque.

OPERATOR CAB (CONT’D) Lowering the Operator Cab Always stop the engine before raising or lowering the cab.

NOTE: Make sure the seat bar is fully raised or lowered when lowering the cab. Always use the grab handles to lower the cab.

Figure PM-11

Pull down on the bottom of the operator cab until it stops at the latching mechanism.

Emergency Exit The front opening on th e cab and rear window provide exits.

Release the latching mechanism (Inset) [Figure PM-9] and pull the cab all the way down.

Rear Window: (If Equipped)

Figure PM-10

Figure PM-12

Install the plate and nut (both sides) [Figure PM-10].

Pull on the tag on the top of the rear window to remove the rubber cord [Figure PM-12].

Push the rear window out of the rear of the cab.

73 of 134

PM-11

864 Bobcat Loader Operation and Maintenance Manual

Dealer Copy -- Not for Resale

Figure PM-9

OPERATOR CAB (CONT’D)

Figure PM-15

Emergency Exit (Cont’d) Figure PM-13

Push with your foot, near the edge of the window (X), to remove the window [Figure PM-15].

Exit through the front door.

Exit through the rear of the cab [Figure PM-13].

Dealer Copy -- Not for Resale

Front Door: (If Equipped) Figure PM-14

NOTE: When an Operator Cab Enclosure Kit is installed, the window of the front door can be used as an emergency exit [Figure PM-14].

Pull the plastic loop at the top of the window in the front door to remove the rubber cord [Figure PM-14].

74 of 134

PM-12

864 Bobcat Loader Operation and Maintenance Manual

SEAT BAR RESTRAINT SYSTEM (FOOT PEDALS)

Maintaining The Seat Bar

The seat bar restraint system has a pivoting seat bar with arm rests and hydraulic valve spool interlocks for the lift and tilt functions.

See the SERVICE SCHEDULE in this manual and on the loader for correct service interval. (See SERVICE SCHEDULE on Page PM-7.)

The operator controls the use of the seat bar. The seat bar in the down position helps to keep the operator in the seat.

Figure PM-16

The spool interlocks require the operator to lower the seat bar in order to ope rate the foot pedal controls (If equipped).

When the seat bar is down, the PRESS TO OPERATE LOADER Button is activated and the engine is running, the lift, tilt, and traction drive functions can be operated.

When the seat bar is up, the lift and tilt control pedals are locked when returned to the NEUTRAL position.

Use compressed air to clean any debris or dirt from the pivot points (Item 1) [Figure PM-16]. Do not l ubricate.

Inspect all mounting hardware. The correct bolt torque is 26 ft.-lb. (35 N•m).

Sit in the seat and fasten the seat belt. Engage the parking brake. Pull the seat bar all the way down. Start the engine. Press the PRESS TO OPERATE LOADER Button. Operate each foot pedal to check that both the lift and tilt functions operate correctly. Raise the lift arms until the attachment is about 2 fe et (600 mm) off the ground.

If the seat bar system and hydraulic valve spool interlocks do not function correctly check all electrical wiring and connections. Replace parts that are worn or damaged. Use only genuine Bobcat replacement parts.

Raise the seat bar. Try to move each foot pedal. Pedals must be firmly locked in the NEUTRAL position. There must be no mo tion of th e lift arms or tilt (attachment) when the controls are moved.

WARNING

Pull the seat bar down, press the PRESS TO OPERATE LOADER Button, lower the lift arms. Operate the lift control. While the lift arms are going up, raise the seat bar. The lift arms must stop.

AVOID INJURY OR DEATH The Seat Bar System must lock the lift and tilt foot pedals or hand controls in neutral when the Seat Bar is up. Service the system if controls do not lock correctly.

Lower the seat bar, press the PRESS TO OPERATE LOADER Button, lower the lift arms and put th e attachment flat on the ground. Stop the engine. Raise the seat bar and operate the foot pedals to be sure that the pedals are firmly locked in the NEUTRAL position.

Unfasten the seat belt.

75 of 134

W-2263-0597

PM-13

864 Bobcat Loader Operation and Maintenance Manual

Dealer Copy -- Not for Resale

Inspecting The Seat Bar

SEAT BAR RESTRAINT SYSTEM ADVANCED HAND CONTROLS (AHC) AND ADVANCED CONTROL SYSTEM (ACS)

Inspecting The Seat Bar Sit in the seat. Turn the key ON (Standard Panel), press RUN /ENTER Button (Deluxe Panel), lower the seat bar and press the PRESS TO OPERATE LOADER Button.

Figure PM-17

Move each hand control back and forth. You should hear the zip-zip sound of the lift and tilt actuators moving the control valve spools (under the seat).

Raise the seat bar fully. Move each hand control back and forth. There must be no zip-zip sound of the lift or tilt actuators. If either actuator makes a sound while the seat bar is raised, contact your dealer for service.

Maintaining The Seat Bar

The seat bar restraint system [Figure PM-17] has a pivoting seat bar with arm rests.

Use compressed air to clean any debris or dirt from the pivot parts (Item 1) [Figure PM-17]. Do not lubricate.

Inspect all mounting hardware. The correct bolt torque is 26 ft.-lb. (35 N•m).

The operator controls the use of the seat bar. The seat bar in the down position helps to keep the operator in the seat.

If the seat bar system does not function correctly, replace parts that are worn or damaged. Use only genuine Bobcat replacement parts.

When the seat bar is down, engine running and the PRESS TO OPERATE LOADER Button is pressed, the lift, tilt, and traction drive functions can be operated.

When the seat bar is up, the lift, tilt and traction drive functions are deactivated.

WARNING The seat bar system must deactivate the lift and tilt control functions when the seat bar is up. Service the system if hand controls do not deactivate.

W-2355-0799

76 of 134

PM-14

864 Bobcat Loader Operation and Maintenance Manual

Dealer Copy -- Not for Resale

See the SERVICE SCHEDULE in this manual and on the loader for correct service interval. (See SERVICE SCHEDULE on Page PM-7.)

BOBCAT INTERLOCK CONTROL SYSTEM (BICS)

Inspecting The Traction Lock (Engine RUNNING)

Inspecting The BICS Controller (Engine STOPPED Key ON)

6. Fasten the seat belt, disengage the parking brake pedal, press the PRESS TO OPERATE LOADER Button and raise the Seat Bar fully. Move the steering levers slowly forward and backward. The TRACTION lock should be engaged. Lower the Seat Bar. Press the PRESS TO OPERATE LOADER Button.

Figure PM-18

7. Engage the pa rking brake pedal and move the steering levers slowly forward and bac kward. The TRACTION lock should be engaged.

NOTE: * The TRACTION light on the left instrument panel will remain OFF until the engine is started, the PRESS TO OPERATE LOADER Button is pressed and the parking brake is disengaged.

AVOID INJURY OR DEATH The Bobcat Interlock Control System (BICS) must deactivate the lift, tilt and traction drive functions. If it does not, contact your dealer for service. DO NOT modify the system.

W-2151-0394

2. Raise the Seat Bar fully. All four BICS lights (Items 1, 2, 3, & 4) [Figure PM-18] [PRESS TO OPERATE LOADER, SEAT BAR, LIFT & TILT VALVE and TRACTION*] on left instrument panel should be OFF [Figure PM-18].

Inspecting The Lift Arm By-Pass Control 8. Raise the lift arms 6 feet (2 meters) off the ground.

Stop the engine.

NOTE: Record what lights are blinking (if any) and the number of light flashes. (See SYSTEM SETUP & ANALYSIS on Page SA-1.)

Turn the lift arm by-pass control knob clockwise 1/4 turn. Pull up and hold the lift arm by-pass control knob until the lift arms slowly lower.

Inspecting Deactivation Of The Auxiliary Hydraulics System (Engine STOPPED - Key ON) 3. Sit in the op erator's seat, lower the Se at Bar, and press the PRESS TO OPERATE LOADER Button.

Press the au xiliary hydraulics FLOW Button. The auxiliary FLOW Button light will come ON. Raise the Seat Bar. The light should be OFF. Inspecting The Seat Bar Sensor (Engine RUNNING) 4. Sit in the operator's seat, lower the seat bar, engage the parking brake pedal and fasten the seat belt.

5. Start the engine and operate at lo w idle. Press the PRESS TO OPERATE LOADER Button. While raising the lift arms, raise the Seat Bar fully. The lift arms should stop. Repeat using the tilt function.

77 of 134

PM-15

864 Bobcat Loader Operation and Maintenance Manual

Dealer Copy -- Not for Resale

WARNING

1. Sit in the operator's seat. Turn k ey ON (Standard Panel), press RUN / ENTER Button (Deluxe Panel, lower the Seat Bar and disengage the parking brake pedal. Press the PRESS TO OPERATE LOADER Button. Three BICS lights (Items 1, 2 , & 3 ) [Figure PM-18] [PRESS TO OP ERATE LOADER, SEAT BAR, and LIFT & TILT VALVE] on left instrument panel should be ON [Figure PM-18].

BOBCAT INTERLOCK CONTROL SYSTEM (BICS) (CONT’D)

TRACK TENSION Track tension is important for good performance and to prevent the tracks from derailing.

Additional Inspection For Loaders With Advanced Hand Controls (AHC) and Advanced Control System (ACS)

NOTE: The wear of track rollers vary with the working conditions and different types of soil conditions.

9. Sit in the operator's seat and fasten the Seat Belt.

Lower the S eat Bar, start the e ngine and press the PRESS TO OPERATE LOADER Button.

Park the loader on a level surface.

10. Raise the lift arms about 6 feet (2 meters) off the ground.

Figure PM-19

11. Turn key OFF (Standard Panel), press the STOP Button (Deluxe Panel, and wait for the engine to come to a complete stop.

13. Move the right hand control away from the operator.

The bucket (or attachment) should not tilt forward.

Raise one side of the lo ader and put j ackstands at the front and rear of the lo ader frame so that the tr ack is about 3 inches (76 mm) off the ground [Figure PM-19].

Lower the loader to the jackstands. Be sure the jackstands do not touch the tracks.

Figure PM-20

Measure the track sag at e ither middle track roller [Figure PM-19]. DO NOT put your fingers into the pinch points between the track and the roller. Use a 1/2 to 5/8 inch bolt, dowel or block to check the gap ( Item 1) [Figure PM-19], & [Figure PM-20].

78 of 134

PM-16

864 Bobcat Loader Operation and Maintenance Manual

Dealer Copy -- Not for Resale

12. Turn key ON (St andard Panel), press RUN/ENTER Button (Deluxe Panel. Press the PRESS TO OPERATE LOADER Button, move the left hand control toward the operator. The lift arms should not lower.

TRACK TENSION (CONT’D)

Decrease Track Tension Pressure must be released from the spring and adjustment cylinder to decrease track tension.

WARNING

Figure PM-22

AVOID INJURY Keep fingers and hands out of pinch points when checking the track tension.

W-2142-0903

Install the bleed tool (MEL-1560) on the bleed fitting (Item 1) [Figure PM-22], adjust and tighten the collar to fi t behind the edge of the access hole and the cover.

Figure PM-23

Loosen the cover bolts and turn the cover down [Figure PM-21].

Adjusting

Increase Track Tension

Tighten the cover bolt (Item 1) [Figure PM-23] to secure the tool.

Add grease to the adjustment fitting (Item 1) [Figure PM21] until the track adjustment is correct [Figure PM-19] & [Figure PM-20].

Turn the tool 1/4 turn counterclockwise and let the grease flow into a container. Turn the tool one additional turn to continue to release pressure [Figure PM-23].

NOTE: Do not remove adjustment fitting unless pressure is released.

Raise the loader. Remove the jackstands.

Repeat the procedure for the other track.

NOTE: If replacement is necessary, always replace adjustment fitting (Item 1) [Figure PM-19] with genuine Bobcat Parts. The fitting is a special fitting designed for high pressure.

79 of 134

Dispose of th e grease in an e nvironmentally safe manner.

PM-17

864 Bobcat Loader Operation and Maintenance Manual

Dealer Copy -- Not for Resale

Figure PM-21

REAR DOOR

WARNING

Opening And Closing The Rear Door

Keep the rear door closed when operating the machine. Failure to do so could seriously injure a bystander.

WARNING

W-2020-1285

AVOID INJURY OR DEATH Never service or adjust the machine when the engine is running unless instructed to do so in the manual.

Adjusting The Rear Door

W-2012-0497

Figure PM-25

The door latch catch (Item 1) [Figure PM-25] can be adjusted side to side for alignment with the door latch mechanism.

The door latch mechanism (Item 2) [Figure PM-25] can be adjusted backward or forward for alignment with the door catch.

Close the rear door before operating the loader.

Put your fingers into the slot in the rear door and pull on the latch handle [Figure PM-24].

Pull the rear door open.

Push the door stop up i nto the hinge (Item 1) [Figure PM-24], then close the rear door.

80 of 134

PM-18

864 Bobcat Loader Operation and Maintenance Manual

Dealer Copy -- Not for Resale

Figure PM-24

PIVOT PINS

Figure PM-26

Figure PM-28

Open the rear door [Figure PM-26].

All lift arm and c ylinder pivots have a la rge pin held in position with a retainer bolt and lock nut (Item 1) [Figure PM-28].

Figure PM-27

Check that the lock nuts are tightened to 18-20 ft.-lb. (2427 N•m) torque.

Raise the rear grill [Figure PM-27].

The rear grill is held open by a cylinder (Item 1) [Figure PM-27].

81 of 134

PM-19

864 Bobcat Loader Operation and Maintenance Manual

Dealer Copy -- Not for Resale

REAR GRILL

AIR CLEANER SERVICE

Outer Filter

Replacing Filter Element

Figure PM-31

Figure PM-29

Disengage the clamps (Item 1) and remove the dust cover (Item 1) [Figure PM-31].

It is important to change the air filter element only when the Air Cleaner Icon in the right panel is ON (Item 1) [Figure PM-29] and you hear three beeps from the alarm.

Dealer Copy -- Not for Resale

Figure PM-32

Replace the inner filter every third time the outer filter is replaced or as indicated on Page 55.

Figure PM-30

Remove the outer filter element (Item 1) [Figure PM-32].

NOTE: * Make sure all sealing surfaces are free of dirt and debris.

Install a new outer element.

Install the dust cover and fasten the clamps.

Press and hold the LIGHT Button (Item 1) [Figure PM30] for two seconds.

Check the air intake hose and the air cleaner housing for damage. Make sure all connections are tight.

If the fi lter element needs replacement, the CODE [0117] (Air Filter Plugged) will show in the HOURMETER / CODE DISPLAY (Item 2) [Figure PM-30].

82 of 134

PM-20

864 Bobcat Loader Operation and Maintenance Manual

AIR CLEANER SERVICE (CONT’D) Replacing Filter Element (Cont’d) Inner Filter Only replace the inner filter element under the following conditions: •

Replace the in ner filter element every third time the outer filter is replaced.

•

After the outer element has been replaced, start the engine and run at full RPM. If the HOURMETER / CODE DISPLAY shows [01-17] (Air Filter Plugged), replace the inner filter element.

Dealer Copy -- Not for Resale

Figure PM-33

Remove the inner filter element (Item 1) [Figure PM-33].

NOTE: Make sure all sealing surfaces are free of dirt and debris.

Install the new inner element.

Figure PM-34

Install the dust cover and fasten the cl amps (Item 1) [Figure PM-34].

83 of 134

PM-21

864 Bobcat Loader Operation and Maintenance Manual

FUEL SYSTEM

Figure PM-36

Fuel Specifications Use only clean, high quality diesel fuel, Grade No. 2 or Grade No. 1.

The following is one suggested blending guideline which should prevent fuel gelling during cold temperatures: TEMP. F° (C°)

NO. 2

NO. 1

+15° (9°)

100%

0%

Down to -20° (-29°)

50%

50%

Below -20° (-29°)

0%

100%

Contact your fuel supplier for local recommendations.

Use a clean, approved safety container to add fuel of the correct specifications. Add fuel only in an area that has free movement of air and no open flames or sparks. NO SMOKING! [Figure PM-36].

Filling The Fuel Tank

WARNING

Fuel Filter See the SERVICE SCHEDULE for the service interval for removing water from, or replacing the fu el filter. (See SERVICE SCHEDULE on Page PM-7.)

Stop and cool the engine before adding fuel. NO SMOKING! Failure to obey warnings can cause an explosion or fire.

W-2063-0887

Figure PM-37 Figure PM-35

Loosen the drain (Item 1) [Figure PM-37] at the bottom of the filter element to remove water from the filter.

Remove the fuel fill cap (Item 1) [Figure PM-35].

Remove the filter element (Item 2) [Figure PM-37].

WARNING

Clean the area around the filter housing. Put clean oil on the seal of the new filter element. Install the fuel filter, and hand tighten.

Always clean up spilled fuel or oil. Keep heat, flames, sparks or lighted tobacco away from fuel and oil.

Failure to use care around combustibles can cause explosion or fire which can result in injury or death.

Remove the air from the fuel system. (See Removing Air From The Fuel System on Page PM-23.)

W-2103-1285

84 of 134

PM-22

864 Bobcat Loader Operation and Maintenance Manual

Dealer Copy -- Not for Resale

Install and tighten the fuel fill cap [Figure PM-35].

FUEL SYSTEM (CONT’D)

Removing Air From The Fuel System

Fuel Lift Pump Strainer

After replacing the fuel filter element or when the fuel tank has run out of fuel, the air must be removed from the fuel system before starting the engine.

Figure PM-38

WARNING Diesel fuel or hydraulic fluid under pressure can penetrate skin or eyes, causing serious injury or death. Fluid leaks under pressure may not be visible.

Use a piece of cardboard or wood to find leaks. Do not use your bare hand. Wear safety goggles. If fluid enters skin or eyes, get immediate medical attention from a physician familiar with this injury.

W-2072-0496

Squeeze the hand pump (prining bulb) (Item 2) [Figure PM-38] until fuel flows from the vent with no air bubbles.

Close the vent (Item 1) [Figure PM-38].

WARNING Always clean up spilled fuel or oil. Keep heat, flames, sparks or lighted tobacco away from fuel and oil.

Failure to use care around combustibles can cause explosion or fire which can result in injury or death.

Loosen the bolt and remove the cover and strainer (Item 1) [Figure PM-38].

W-2103-1285

Clean the strainer with clean diesel fuel.

Install the strainer and cover and tighten bolt.

85 of 134

PM-23

864 Bobcat Loader Operation and Maintenance Manual

Dealer Copy -- Not for Resale

Open the vent plug (Item 1) [Figure PM-38] at the top of the fuel filter.

FUEL SYSTEM (CONT’D)

Figure PM-41

Removing Fuel From The Fuel Tank The fuel tank is located between the sides of the Main Frame of the loader.

Figure PM-39

Remove the drain plug (Item 1) [Figure PM-41] (viewed from outside of loader through access hole between tracks and frame) and drain the fuel from the tank.

Install plug and tighten the bo lts on the access cover before filling with fuel.

There is an access cover under the Main Frame at the left side of the loader [Figure PM-39].

Loosen the two b olts [Figure PM-39] on the access cover.

Figure PM-40

Pivot the access cover (Item 1) [Figure PM-40] to expose the drain plug on the fuel tank.

86 of 134

PM-24

864 Bobcat Loader Operation and Maintenance Manual

Dealer Copy -- Not for Resale

Dispose of the fuel in an environmentally safe manner.

Put oil on the new filter gasket. Install the filter and hand tighten.

ENGINE LUBRICATION SYSTEM Checking Engine Oil

Remove the fill cap (Item 4) [Figure PM-42]. Put 10 q t.

(9,5L) of oil in the engine.

Check the engine oil level every day before starting the engine for the work shift.

Start the engine and let it run for several minutes.

Figure PM-42

Stop the engine and check for leaks at the oil filter.

Remove the dipstick (Item 1) [Figure PM-42] and check the oil level. Add oil as needed if it is not at the top mark on the dipstick (Item 1) [Figure PM-43].

Open the rear door and remove the dipstick (Item 1) [Figure PM-42].

Install the dipstick and close the rear door.

Keep the oil level between the marks on the dipstick.

Engine oil is also used to provide engine cooling. Check oil level every day for correct engine lubrication and cooling.

WARNING

Use a good quality motor oil that meets API Service Classification of CD or better (See Oil Chart, [Figure PM44]).

Always clean up spilled fuel or oil. Keep heat, flames, sparks or lighted tobacco away from fuel and oil.

Failure to use care around combustibles can cause explosion or fire which can result in injury or death.

Replacing The Oil And Filter

W-2103-1285

See the SERVICE SCHEDULE for the service interval for replacing the engine oil and filter. (See SERVICE SCHEDULE on Page PM-7.)

Figure PM-44

Run the engine until it is at operating temperature. Stop the engine.

Open the rear door and remove the drain plug (Item 2) [Figure PM-42].

Drain the oil into a co ntainer and recycle or dispose of used oil in an environmentally safe manner.

Reinstall the drain plug.

Remove the oil filter (Item 3) [Figure PM-42].

Clean the filter housing surface.

Use genuine Bobcat filter only.

87 of 134

PM-25

864 Bobcat Loader Operation and Maintenance Manual

Dealer Copy -- Not for Resale

Figure PM-43

ENGINE COOLING SYSTEM

Figure PM-46

Cleaning The Cooling System Check the cooling system every day to prevent overheating, loss of performance or engine damage.

Engine oil is used to provide both engine lubrication and cooling. No anti-freeze/water mixture is used for engine cooling.

It is important to check the engine oil level every day to maintain adequate engine lubrication and also engine cooling.

When engine oil is changed, only the oil in the engine oil pan and filter is replaced. Approximately 7 qua rts (6.6 liters) of oil remains in the cooling system (hoses and radiator).

Remove the hair pin (Item 1) [Figure PM-46] (both sides) so the oil cooler can be raised.

When changing engine oil, follow the p rocedures carefully for correct quantity.

Figure PM-45

Raise the oil cooler. Use air pressure or water pressure to clean the top of the engine oil cooler [Figure PM-47].

Raise the rear grill [Figure PM-45].

WARNING

Use air pressure or water pressure to clean the top of the hydraulic/hydrostatic oil cooler [Figure PM-45].

Wear safety glasses to prevent eye injury when any of the following conditions exist: • When fluids are under pressure.

• Flying debris or loose material is present.

• Engine is running.

• Tools are being used.

W-2019-1285

88 of 134

PM-26

864 Bobcat Loader Operation and Maintenance Manual

Dealer Copy -- Not for Resale

Figure PM-47

ELECTRICAL SYSTEM

Fuse Location

Description

Figure PM-49

Figure PM-48

The loader has a 12 volt, negative ground alternator charging system. The electrical system is protected by fuses located in the c ab on the s teering control panel, and a 1 00 amp. master fuse [Figure PM-48] in the engine compartment on the le ft side of the engine. The fuses will protect the electrical system when there is an electrical overload. The reason for the overload must be found before starting the engine again.

Remove the cover to check or replace the fuses.

Figure PM-50

Cleaning Battery And Terminals The battery cables must be clean and tight. Check the electrolyte level in the battery. Add distilled water as needed. Remove acid or corrosion from the bat tery and cables with a s odium bicarbonate (baking soda) and water solution [Figure PM-48].

Put Battery Saver (6664458) or grease on the battery terminals and cable ends to prevent corrosion.

WARNING Batteries contain acid which burns eyes and skin on contact. Wear goggles, protective clothing and rubber gloves to keep acid off body.

In case of acid contact, wash immediately with water.

In case of eye contact get prompt medical attention and wash eye with clean, cool water for at least 15 minutes.

If electrolyte is taken internally drink large quantities of water or milk! DO NOT induce vomiting. Get prompt medical attention.

W-2065-1296

89 of 134

PM-27

864 Bobcat Loader Operation and Maintenance Manual

Dealer Copy -- Not for Resale

The electrical system is protected from overload by fuses and relays under the fuse panel cover (Item 1) [Figure PM-49] A decal is inside the cover to show location and amp ratings.

ELECTRICAL SYSTEM (CONT’D) Fuse Location (Cont’d)

WARNING

The location and sizes are shown below and [Figure PM50].

REF

DESCRIPTION

AMP. REF

DESCRIPTION

AMP.

Front & Marker Lights

R

1

Traction

30

11

2

Fuel Shutoff

30

12 Fuel Shutoff

R

3

Not Used

--

13 Rear Lights

R

4

Not Used

--

14 Traction

R

5

Heater

25

15 Switch Power

R

6

Front & Marker Lights

15

16 Starter

R

7

Rear Lights

15

17 Unswitched Attach.

25

8

Bobcat Controller

25

18 Switched Attach.

25

9

Not Used

--

19 Alt. & Accessories

25

10 Glow Plugs

R

20 Accessory Plug

25

Keep arcs, sparks flames and lighted tobacco away from batteries. When jumping from booster battery make final connection (negative) at machine frame.

Do not jump start or charge a frozen or damaged battery. Warm battery to 60°F (16°C) before connecting to a charger. Unplug charger before connecting or disconnecting cables to battery. Never lean over battery while boosting, testing or charging.

Battery gas can explode and cause serious injury.

W-2066-0705

Figure PM-51

R - Relay

Dealer Copy -- Not for Resale

Using A Booster Battery (Jump Starting) If it is necessary to use a booster battery to start the engine, BE CAREFUL! There must be one person in the operator's seat and one person to co nnect and disconnect the battery cables.

The key switch must be OFF (Standard Panel) OR the STOP Button must be pressed (Deluxe Panel). The booster battery must be 12 volt.

WARNING Batteries contain acid which burns eyes and skin on contact. Wear goggles, protective clothing and rubber gloves to keep acid off body.

In case of acid contact, wash immediately with water.

In case of eye contact get prompt medical attention and wash eye with clean, cool water for at least 15 minutes.

If electrolyte is taken internally drink large quantities of water or milk! DO NOT induce vomiting. Get prompt medical attention.

Connect the end of the first cable (Item 1) [Figure PM51] to the positive (+) terminal of the booster battery.

Connect the other end of the same cable (Item 2) [Figure PM-51] to the positive terminal on the loader starter.

W-2065-1296

Connect the end of the se cond cable (Item 3) [Figure PM-51] to the negative (-) terminal of the booster battery.

Connect the other end of the same cable (Item 4) [Figure PM-51] to the engine.

Keep cables away from moving parts. Start the engine.

(See STARTING THE ENGINE on Page OI-22.)

90 of 134

PM-28

864 Bobcat Loader Operation and Maintenance Manual

Figure PM-52

ELECTRICAL SYSTEM (CONT’D) Using A Booster Battery (Jump Starting) (Cont’d) After the engine has started, remove the ground (-) cable (Item 4) [Figure PM-51] first.

Remove the c able from the po sitive terminal (Item 2) [Figure PM-51].

IMPORTANT Damage to the alternator can occur if: • Engine is operated with battery cables disconnected.

• Battery cables are connected when using a fast charger or when welding on the loader. (Remove both cables from the battery.)

• Extra battery cables (booster cables) are connected wrong.

Disconnect the negative (-) cable (Item 1) [Figure PM52].

Disconnect the main frame ground bolt and cable clamp (Item 2) [Figure PM-52].

Figure PM-53

Dealer Copy -- Not for Resale

I-2023-1285

Removing And Installing The Battery

WARNING Batteries contain acid which burns eyes and skin on contact. Wear goggles, protective clothing and rubber gloves to keep acid off body.

In case of acid contact, wash immediately with water.

In case of eye contact get prompt medical attention and wash eye with clean, cool water for at least 15 minutes.

Remove the battery hold down clamp (Item 1) [Figure PM-53].

If electrolyte is taken internally drink large quantities of water or milk! DO NOT induce vomiting. Get prompt medical attention.

Disconnect the positive (+) cable (Item 2) [Figure PM-53] from the battery.

W-2065-1296

Remove the battery from the loader.

Open the rear door.

91 of 134

PM-29

864 Bobcat Loader Operation and Maintenance Manual

ELECTRICAL SYSTEM (CONT’D)

Figure PM-55

Removing And Installing The Battery (Cont’d) Figure PM-54

Always clean the battery terminals and cable ends when installing a new or used battery [Figure PM-54].

WARNING

When installing the battery in the loader, do not touch any metal parts with the battery terminals.

Keep arcs, sparks flames and lighted tobacco away from batteries. When jumping from booster battery make final connection (negative) at machine frame.

Connect the negative (-) cable last to prevent sparks.

Connect and tighten the battery cables.

Do not jump start or charge a frozen or damaged battery. Warm battery to 60°F (16°C) before connecting to a charger. Unplug charger before connecting or disconnecting cables to battery. Never lean over battery while boosting, testing or charging.

Battery gas can explode and cause serious injury.

W-2066-0705

92 of 134

PM-30

864 Bobcat Loader Operation and Maintenance Manual

Dealer Copy -- Not for Resale

Install cable clamp and ground bolt (Item 1) [Figure PM55] as shown for correct ground and cable routing.

HYDRAULIC/HYDROSTATIC SYSTEM

Replacing Hydraulic/Hydrostatic Filter

Checking And Adding Fluid

See the SERVICE SCHEDULE for the correct service interval. (See SERVICE SCHEDULE on Page PM-7.)

Use only recommended fluid in the hydraulic system.

(See 864/864H COMPACT TRACK LOADER SPECIFICATIONS on Page SPEC-3.)

Raise the operator cab. (See Raising The Operator Cab on Page PM-10.)

Figure PM-58

Put the loader on a level surface.

Lower the lift arms and tilt the Bob-Tach fully back.

Stop the engine.

Figure PM-56

Clean the surface of the fi lter housing where the filter seal contacts the housing. Put clean oil on the seal of the new filter element.

Install and hand tighten the filter element.

Check the fluid level in the sight gauge [Figure PM-56].

WARNING

Figure PM-57 Diesel fuel or hydraulic fluid under pressure can penetrate skin or eyes, causing serious injury or death. Fluid leaks under pressure may not be visible.

Use a piece of cardboard or wood to find leaks. Do not use your bare hand. Wear safety goggles. If fluid enters skin or eyes, get immediate medical attention from a physician familiar with this injury.

W-2072-0496

Lower the operator cab.

Start the e ngine and operate the l oader hydraulic controls.

Stop the engine and check for leaks at the filter.

Check the fluid level in the reservoir and add as needed.

Remove the fill cap (Item 1) [Figure PM-57].

Add the fluid as needed to bring the level to the center of the sight gauge.

WARNING

NOTE: Before installing the fill breather cap, make sure the rubber gasket is installed on the cap (Inset) [Figure PM-57]. (See Hydraulic Reservoir Breather Cap on Page PM-33.)

Always clean up spilled fuel or oil. Keep heat, flames, sparks or lighted tobacco away from fuel and oil.

Failure to use care around combustibles can cause explosion or fire which can result in injury or death.

W-2103-1285

Install the fill cap [Figure PM-57].

93 of 134

PM-31

864 Bobcat Loader Operation and Maintenance Manual

Dealer Copy -- Not for Resale

Remove the filter (Item 1) [Figure PM-58].

HYDRAULIC/HYDROSTATIC SYSTEM (CONT’D)

Hydraulic Fill Screen

Replacing The Hydraulic Fluid

Figure PM-60

See the SERVICE SCHEDULE for the c orrect service interval. (See SERVICE SCHEDULE on Page PM-7.)

Replace the fluid if it be comes contaminated or after major repair.

Always replace the hydraulic/hydrostatic filter (See Replacing Hydraulic/Hydrostatic Filter on Page PM-31.) and clean the h ydraulic fill screen and the case drain filters whenever the hydraulic fluid is replaced.

Remove the fill cap and raise the operator cab. (See Raising The Operator Cab on Page PM-10.)

Figure PM-59

Remove The Hose Clamps And Hose (Item 1) [Figure PM-60]. Remove The Screen (Item 2) [Figure PM-60].

Case Drain Filters

WARNING Hydraulic fluid escaping under pressure can have sufficient force to enter a person’s body by penetrating the skin. This can cause serious injury and possible death if proper medical treatment by a physician familiar with this injury is not received immediately.

Remove the left hydrostatic motor cover (Item 1) [Figure PM-59]. Route the d rain hose through the access hole, remove the plug and drain the oil into a c ontainer.

Recycle or dispose of the used fluid in a n environmentally safe manner.

W-2145-0290

WARNING Always clean up spilled fuel or oil. Keep heat, flames, sparks or lighted tobacco away from fuel and oil.

Failure to use care around combustibles can cause explosion or fire which can result in injury or death.

W-2103-1285

94 of 134

PM-32

864 Bobcat Loader Operation and Maintenance Manual

Dealer Copy -- Not for Resale

Wash The Screen In Clean Solvent And Air Dry.

HYDRAULIC/HYDROSTATIC SYSTEM (CONT’D)

Hydraulic Reservoir Breather Cap

Replacing The Hydraulic Fluid (Cont’d)

See the SERVICE SCHEDULE for the correct service interval. (See SERVICE SCHEDULE on Page PM-7.)

Figure PM-61

Figure PM-63

Figure PM-62

Clean the filter in the breather cap.

Replace the breather cap if it is worn or damaged, or beyond the specified service interval.

Replace both hydrostatic motor case drain filters (Item 1) [Figure PM-61] & [Figure PM-62].

Install new case drain filters and tighten all the hoses.

Replace the hydraulic/hydrostatic filter element. (See Replacing Hydraulic/Hydrostatic Filter on Page PM-31.)

Add the correct fluid to t he reservoir until the level is between the marks on the dipstick. Do not fill above the top mark on the dipstick.

Lower the cab. (See Lowering the Operator Cab on Page PM-11.)

Start the engine and operate the loader hydraulic controls.

Stop the engine and check for leaks.

Check the fluid level in the reservoir and add as needed.

95 of 134

PM-33

864 Bobcat Loader Operation and Maintenance Manual

Dealer Copy -- Not for Resale

Remove the breather cap (Item 1) [Figure PM-63].

HYDROSTATIC MOTOR CARRIER OIL

TRACK ROLLER AND IDLER LUBRICATION

See the SERVICE SCHEDULE for the correct interval.

(See SERVICE SCHEDULE on Page PM-7.)

The four track rollers and eight idlers have an oil reservoir for bearing lubrication.

Removing And Replacing Oil

See the SERVICE SCHEDULE for the correct interval.

(See SERVICE SCHEDULE on Page PM-7.)

Park the loader so that the plug in the hydrostatic motor carrier is at the bottom.

Removing And Replacing Oil

Remove the plug and let the oil drain from the motor carrier.

Figure PM-65

Dealer Copy -- Not for Resale

Figure PM-64

Rotate the motor carrier so that the plug is horizontal with the center of the m otor carrier (Inset) [Figure PM-64].

Add synthetic oil (P/N 6682546) as necessary until it flows from the hole.

Install and tighten plug to 17 ft.-lb. (23 N•m) torque.

Repeat for the other hydrostatic motor carrier.

Recycle or dispose of us ed fluid in an env ironmentally safe manner.

Remove the plug (item 1 or 2) [Figure PM-65] and rotate the roller (or idler) to drain the oil.

Rollers & Idlers: Add 3.4 oz. (100 cc) of oil (SAE 10W-40) to the rollers and idlers (both sides of loader).

Install and tighten plug to 17 ft.-lb. (23 N•m) torque.

Recycle or dispose of us ed fluid in an en vironmentally safe manner.

96 of 134

PM-34

864 Bobcat Loader Operation and Maintenance Manual

FAN GEARBOX See the SERVICE SCHEDULE for the correct service interval. (See SERVICE SCHEDULE on Page PM-7.)

Checking And Maintaining Raise the operator cab. (See Raising The Operator Cab on Page PM-10.)

Dealer Copy -- Not for Resale

Figure PM-66

Remove the plug (Item 1) [Figure PM-66]. Fluid level is correct when fluid is at the bottom of the check plug hole.

If the level is low, add SAE 90w gear lubricant until it flows from the hole.

Install and tighten the plug.

Lower the operator cab. (See Lowering the Operator Cab on Page PM-11.)

97 of 134

PM-35

864 Bobcat Loader Operation and Maintenance Manual

DRIVE BELT

Figure PM-69

Adjusting The Drive Belt Figure PM-67

Loosen the two stop mounting bolts (Item 1) [Figure PM69].

Loosen the spring tension bolt (Item 2) [Figure PM-69].

Remove the drive belt from the hydrostatic pump, and flywheel pulley.

The drive belt idler arm stop Is located on the left side of the engine below the air cleaner [Figure PM-67].

Figure PM-70 Loosen the two bolts (Item 1) [Figure PM-67] and slide the stop against the idler arm. Tighten the bolts.

There is no adjustment for the spring, Just make sure the spring bolt (Item 2) [Figure PM-67] Is tight.

Replacing The Drive Belt Stop the engine.

Open the rear door.

Figure PM-68

Remove the drive belt (Item 1) [Figure PM-70].

Install new dr ive belt and adjust the drive belt idler arm stop. (See Adjusting The Drive Belt on Page PM-36.)

Remove the three belt shield fasteners (Item 1) [Figure PM-68].

Remove the belt shield (Item 2) [Figure PM-68].

98 of 134

PM-36

864 Bobcat Loader Operation and Maintenance Manual

Dealer Copy -- Not for Resale

Remove the fan drive belt from the tensioner pulley.

Adjusting The Alternator Belt

Move the alternator until the belt has 5/16 inch (8,0 Mm) movement at the middle of the belt span with 15 lb. (66 N) of force [Figure PM-72].

Stop the engine.

Tighten the adjustment and mounting bolts.

Figure PM-71

TIMING BELT

ALTERNATOR BELT

Loosen the alternator mounting and adjustment bolts (Item 1) [Figure PM-71].

The timing belt (Item 1) [Figure PM-73] must be replaced every 3,000 hours or every 5 years.

Figure PM-72

99 of 134

PM-37

864 Bobcat Loader Operation and Maintenance Manual

Dealer Copy -- Not for Resale

Figure PM-73

LUBRICATION OF THE BOBCAT LOADER

Figure PM-76

Lubricate the loader as specified in the SERVICE SCHEDULE for the best performance of the loader. (See SERVICE SCHEDULE on Page PM-7.)

Record the operating hours each time you lubricate the Bobcat Loader.

Always use a good quality lithium based multi-purpose grease when you lubricate the loader. Apply the lubricant until extra grease shows.

Lubricate the following locations on the loader:

3. Lift arm pivot pin (both sides) [Figure PM-76].

Figure PM-74

1. Rod end lift cylinder (both sides) [Figure PM-74].

4. Base end tilt cylinder [Figure PM-77].

Figure PM-75

Figure PM-78

6

2. Base end lift cylinder (both sides) [Figure PM-75].

5. Rod end tilt cylinder [Figure PM-78].

6. Bob-tach pivot pin (both sides) [Figure PM-78].

7. Bob-tach wedge (both sides) [Figure PM-78].

100 of 134

PM-38

864 Bobcat Loader Operation and Maintenance Manual

Dealer Copy -- Not for Resale

Figure PM-77

LUBRICATION OF THE BOBCAT LOADER (CONT’D) Figure PM-79

Dealer Copy -- Not for Resale

8. 250 hours: steering lever shaft (2) [Figure PM-79].

101 of 134

PM-39

864 Bobcat Loader Operation and Maintenance Manual

Raise the cab and remove the evaporator cover (Item 1) [Figure PM-81].

HEATER AND AIR CONDITIONING Cleaning and Maintenance

Use low pressure water or air to remove debris from the evaporator fins.

The heater and air conditioning require regular inspection and maintenance. (See SERVICE SCHEDULE on Page PM-7 for intervals.)

Install the cover.

Filters

Air Conditioner Belt Adjustment

Figure PM-80

The Fresh Air Filter is located below the rear window of the cab (Item 1) [Figure PM-80].

Loosen the mounting and adjustment bolts (Item 1) [Figure PM-82]. Move the compressor forward to tighten the belt. Tighten the m ounting and adjustment bolts.

Check regularly for belt wear.

Remove the bolts and remove the filter housing.

Shake the filter or use low air pressure to remove dirt.

Air Conditioner Lubrication

Reinstall the filter and housing.

Run the air conditioner for about 5 minutes every week to lubricate the internal components.

The Recirculation Filter is located in front o f the rear window inside the cab (Item 2) [Figure PM-80].

Troubleshooting

Remove the clamping knobs, grill and filter.

If the fan does not run, or the air conditioning does not turn on, check the fuse. (See ELECTRICAL SYSTEM on Page PM-27.)

Clean the filter with water and mild detergent. Reinstall the filter.

If the ai r conditioning system circulates warm air, the refrigerant may need to be recharged.

Evaporator Figure PM-81

102 of 134

PM-40

864 Bobcat Loader Operation and Maintenance Manual

Dealer Copy -- Not for Resale

Figure PM-82

Figure PM-85

BOB-TACH Inspection And Maintenance Figure PM-83

Move the bob-tach levers to engage the wedges [Figure PM-83]. The levers and wedges must move freely.

If the wedge does not contact the lower edge of the hole [Figure PM-85], The attachment will be lo ose and can come off the bob-tach.

The wedges must extend through the holes in th e attachment mounting frame (Item 1) [Figure PM-83].

Figure PM-86

WARNING Bob-Tach wedges must extend through the holes in attachment. Levers must be fully down and locked.

Failure to secure wedges can allow attachment to come off and cause injury or death.

W-2102-0588

Figure PM-84

Inspect the mounting frame on th e attachment and the bob-tach, linkages and wedges for excessive wear or damage [Figure PM-86]. Replace any parts that are damaged, bent, or missing. Keep all fasteners tight.

Look for cracked welds. Contact your Bobcat dealer for repair or replacement parts.

Lubricate the wedges. (See SERVICE SCHEDULE on Page PM-7.) (See LUBRICATION OF THE BOBCAT LOADER on Page PM-38.)

103 of 134

PM-41

864 Bobcat Loader Operation and Maintenance Manual

Dealer Copy -- Not for Resale

The wedges must extend through the ho les in the attachment mounting frame (Item 1) [Figure PM-84] and must contact the lower edge of the hole in the attachment [Figure PM-84] and (Item 1) [Figure PM-85].

The wedges must extend through the ho les in the attachment mounting frame (Item 1) [Figure PM-88] and must contact the lower edge of the hole in the attachment [Figure PM-88] and (Item 1) [Figure PM-89].

POWER BOB-TACH (OPTION) Inspection And Maintenance Figure PM-87

If the wedge does not contact the lower edge of the hole [Figure PM-89], The attachment will be lo ose and can come off the Bob-tach.

Push and hold the BOB-TACH "WEDGES UP" switch [Figure PM-87] until wedges are fully raised. Push and hold the BOB-TACH "WEDGES UP" switch [Figure PM87] until the we dges are fully down. The wedges must move freely.

Inspect the mounting frame on th e attachment and the Bob-tach, Linkages and wedges for excessive wear or damage [Figure PM-90]. Replace any parts Including decals and lever that are damaged, bent, or missing.

Keep all fasteners tight. Inspect the hoses and fittings for leaks.

Figure PM-88

Look for cracked welds. Contact your Bobcat dealer for repair or replacement parts.

Lubricate the wedges. (See SERVICE SCHEDULE on Page PM-7.) (See LUBRICATION OF THE BOBCAT LOADER on Page PM-38.)

Figure PM-89

104 of 134

PM-42

864 Bobcat Loader Operation and Maintenance Manual

Dealer Copy -- Not for Resale

Figure PM-90

SYSTEM SETUP & ANALYSIS BOBCAT INTERLOCK CONTROL SYSTEM (BICS) . . . . . . . . . SA-3 Troubleshooting Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SA-3 DELUXE INSTRUMENTATION PANEL SETUP . . . . . . . . . . . . . SA-6 DELUXE INSTRUMENTATION SERVICE CODES . . . . . . . . . . SA-4 Deluxe Panel Upgrade. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SA-6 Icon Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SA-6 Deluxe Panel Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SA-7 Passwords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SA-7 Changing the Password. . . . . . . . . . . . . . . . . . . . . . . . . . . . . SA-8 SERVICE CLOCK RESET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SA-9 SYSTEM SETUP & ANALYSIS Dealer Copy -- Not for Resale

SHUTDOWN FEATURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SA-9

SA-1 105 of 134

864 Bobcat Loader Operation & Maintenance Manual

Dealer Copy -- Not for Resale SA-2 106 of 134

864 Bobcat Loader Operation & Maintenance Manual

BOBCAT INTERLOCK CONTROL SYSTEM (BICS)

Figure SA-1

Troubleshooting Chart The following chart shows the effects which can happen to the loader, and the probable causes when the BICS Instrument Panel lights are off. See [Figure SA-1] for location of BICS lights and Ic ons. Have service procedures performed ONLY BY QUALIFIED BOBCAT SERVICE PERSONNEL.

Dealer Copy -- Not for Resale

Press and hold LIGHTS Button (Item 5) [Figure SA-1] for two seconds to view SERVICE CODES in the HOURMETER / CODE DISPLAY (Item 6) [Figure SA-1].

If more than one SERVICE CODE is present, the codes will scroll on the HOURMETER / CODE DISPLAY.

107 of 134

SA-3

864 Bobcat Loader Operation and Maintenance Manual

The following word errors may also be displayed:

DELUXE INSTRUMENTATION SERVICE CODES The hourmeter display on the Left Instrument Panel can change from engine hours to SERVICE CODES (See at right.). These CODES help your dealership analyze monitored functions of your Bobcat Loader. Some service procedures must be performed ONLY BY QUALIFIED BOBCAT SERVICE PERSONNEL. The Prefix, in the left two columns, followed by a Suffix, in the right two columns, will indicate a Function Error.

Press and hold LIGHTS Button (Item 5) [A] (Page 81) for two seconds to view SERVICE CODES in the HOURMETER / CODE D ISPLAY display (Item 6) [A] (Page 81). If more than one SERVICE CODE is present, the codes will scroll on the HOURMETER / CODE DISPLAY.

REPLY

One or both instrument panel(s) not communicating with the controller.

INPUT

The controller not communicating with the left instrument panel.

CODE

The controller is asking for a password. (Deluxe Panel Only)

ERROR

The wrong password was entered. (Deluxe Panel Only)

EXAMPLE: 01-17 Plugged Air Filter SERVICE CODES FUNCTION

SUFFIX

ERROR DESCRIPTION

01

Air Filter

02

Error ON (Detects ON when should be OFF)

02

Hydraulic Charge Filter

03

Error OFF (Detects OFF when should be ON)

03

Battery Voltage

04

In Error

04

Engine Oil Pressure

05

Short To Battery (Detects 12V & should not be)

05

Hydraulic Charge Pressure

06

Short To Ground

06

Engine Speed

07

Open Circuit (Not grounded)

07

Hydraulic Oil Temperature

09

Low

08

Engine Coolant Temperature

10

High

09

Fuel Level

11

Extremely High

11

Seat Bar Sensor

13

No Signal

12

Front Auxiliary PWM (Proportional Control)

13

Fuel Shutoff Solenoid - Secondary

15

In Shutdown

14

Fuel Shutoff Solenoid - Primary

16

Not Connected

15

Traction Lock Solenoid - Primary

17

Plugged

16

Traction Lock Solenoid - Secondary 18

Out Of Range

17

Lift and Tilt Valve Solenoid

21

Out Of Range High (Above detectable range of sensor)

18

Spool Lock Solenoid

22

Out Of Range Low (Below detectable range of sensor)

19

Bucket Positioning Solenoid

23

Not Calibrated

21

Glow Plugs

28

Failure

22

Starter Output

31

Tilt Actuator Fault

Switch 14

Extremely Low

23

Solenoid for Rear Female Coupler

32

Tilt Actuator Wiring Fault

24

Solenoid for Rear Male Coupler

33

Tilt Handle Wiring Fault

25

Rear Auxiliary Relief Solenoid

34

Tilt Actuator Not Calibrated

26

Solenoid for Front Female Coupler

35

Tilt Handle Not Calibrated

27

Solenoid for Front Male Coupler

36

Lift Actuator Fault

28

Diverter Valve Solenoid

37

Lift Actuator Wiring Fault

108 of 134

SA-4

864 Bobcat Loader Operation and Maintenance Manual

Dealer Copy -- Not for Resale

PREFIX

SERVICE CODES FUNCTION

SUFFIX

29

High Flow Auxiliary Solenoid

31

Recovery Mode Failure (Loss of 39 Power)

Lift Actuator Not Calibrated

32

Advanced Hand Controls (AHC) 40 Advanced Control System (ACS) (Selectable Foot/Hand Controls)

Lift Handle Not Calibrated

33

Constant Data Information)

Loader 41

Invalid Frequency From Advanced Hand Controls (AHC)

34

Deluxe Panel Not Downgraded in 48 Error

Multiple Controllers Present - Error

35

Two Speed Fan

49

Lift Actuator Short to Ground

36

Attachment Control Device (ACD) 50 Controller

Tilt Actuator Short to Ground

80

ACD Output A

51

Lift Actuator Short to Battery

81

ACD Output B

52

Tilt Acutator Short to Battery

82

ACD Output C

53

Lift Handle/Pedal Short to Ground

(Stored

38

ERROR DESCRIPTION Lift Handle Wiring Fault

83

ACD Output D

54

Tilt Handle/Pedal Short to Ground

84

ACD Output E

55

Lift Handle/Pedal Short to Battery

85

ACD Output F

56

Tilt Handle/Pedal Short to Battery

86

ACD Output G

57

Lift Acutator Reduced Performance

87

ACD Output H

58

Tilt Actuator Reduced Performance

Multiple SERVICE CODES and / or Abnormal Symptoms can be 59 caused by c orroded or loose groun d connection. Flashing instrument panel lights, alarm beeping, front & rear lights flashing, low battery 60 voltage, loose battery connectors, could also indicate a poor ground.

61 Check all grounds before performing other diagnostics.

62

109 of 134

Lift Acutator Wrong Direction Tilt ACutator Wrong Direction Handle Lock Short to Ground Handle Lock Short to Battery

63

Pedal Lock Short to Ground

64

Pedal Lock Short to Battery

65

Sensor Range

66

Battery Out of Range

67

Switch Moved While Operating

SA-5

864 Bobcat Loader Operation and Maintenance Manual

Supply

Voltage

Out

of

Dealer Copy -- Not for Resale

PREFIX

DELUXE INSTRUMENTATION PANEL SETUP

Icon Identification

Deluxe Panel Upgrade

Make selection by pressing SELECTION BUTTON opposite the Icon.

If you upgrade from a Standard Panel to a Deluxe Panel, press and hold the RUN / ENTER Button for at least 2 seconds to allow the system to recognize the upgrade.

The home screen will then be displayed.

ICON

DESCRIPTION

TOOL / SETUP: Access system options.

Use to set clock, check system warnings, select language, set passwords, etc.

HELP: Access help on current menu item.

EXIT

EXIT returns you to previous level menu.

CLOCK / JOB CLOCK: Press to clear or lock job clock; TOOL / SETUP to set time.

UP ARROW: Goes backward one screen.

DOWN ARROW: Goes forward one screen.

OUTLINE ARROWS: No sc reen available (backward / forward).

SELECTION ARROW: Use to select menu item.

NEXT

INFO YES/NO CLEAR SET

110 of 134

SA-6

Goes to the NE XT screen in series.

EXAMPLE: The next Active Warning screen.

Goes to mo re information about an attachment.

Answer yes / no to current setup question.

Removes previously installed password.

Set accepts current installed password.

864 Bobcat Loader Operation and Maintenance Manual

Dealer Copy -- Not for Resale

LOCK / UNLOCK: Allows machine to be locked / u nlocked. A valid password will need to be entered at startup to run a locked machine. You must lock machine to activate security system.

All new machines with Deluxe Instrumentation arrive at Bobcat Dealerships with the panel in locked mode. This means that a password must be used to start the engine.

DELUXE INSTRUMENTATION PANEL SETUP (CONT’D) Deluxe Panel Setup

Passwords

Display Options

For security purposes, your dealer may change the password and also set it in the locked mode. Your dealer will provide you with the password.

Master Password: A permanent, randomly selected password set at the factory.Allows full use of th e loader and to setup the Deluxe Panel.

User Password: Allows starting and operating the loader; cannot change password or any of the other setup features.

ADJUST CONTRAST SHORTCUT: Press either the left or right arrow keys to adjust the contrast lighter or darker.

111 of 134

SA-7

864 Bobcat Loader Operation and Maintenance Manual

Dealer Copy -- Not for Resale

Owner Password: Allows for full use of the loader and to setup the Deluxe Panel.Owner can select a password to allow starting & operating the loader and modify the setup of the Deluxe Panel. Owner should change the password as soon as possible for security of the loader.

DELUXE INSTRUMENTATION PANEL SETUP (CONT’D)

Dealer Copy -- Not for Resale

Changing the Password

112 of 134

SA-8

864 Bobcat Loader Operation and Maintenance Manual

SHUTDOWN FEATURE Figure SA-2

2

1

3 4 B-15551

Dealer Copy -- Not for Resale

Press and hold the BUCKET POSITIONING Button (Item 1) [Figure SA-2] for two seconds. If t he SHUTDOWN feature is installed, Shtdn will appear in the HOURMETER / CODE DISPLAY (Item 2) [Figure SA-2].

If it is not installed, BASE will appear.

The Operational Code (Software version) will also appear.

See your Bobcat dealer about installation of this feature.

SERVICE CLOCK RESET Press the LIGHTS button (Item 3) [Figure SA-2] to turn the panel ON. Press and hold the HIGH FLOW and A UXILIARY PRESSURE RELEASE buttons (Item 4) [Figure SA-2] simultaneously, until rEsET appears in the display (Item 2).

The Service Clock alerts the operator when the next service interval is due. EXAMPLE: The Service Clock can be set at 250 hour intervals as a reminder for the next service interval.

See your Bobcat dealer about installation of this feature.

113 of 134

SA-9

864 Bobcat Loader Operation and Maintenance Manual

Dealer Copy -- Not for Resale 114 of 134

SA-10

864 Bobcat Loader Operation and Maintenance Manual

MACHINE SIGN TRANSLATIONS DANGER (6717343) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MST-7 DANGER (6718392) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MST-7 DANGER (6718393) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MST-7 IMPORTANT (6560573) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MST-8 LIFT ARM SUPPORT DEVICE (6706558) . . . . . . . . . . . . . . . . MST-9 SERVICE SCHEDULE (6734534). . . . . . . . . . . . . . . . . . . . . . . MST-3 WARNING (6577754) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MST-6 WARNING (6718390) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MST-4 WARNING (6718391) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MST-6

WARNING (6718400) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MST-5

Dealer Copy -- Not for Resale

WARNING (6718397) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MST-8

MACHINE SIGN TRANSLATIONS

WARNING (6804114) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MST-7

MST-1 115 of 134

864 Bobcat Loader Operation & Maintenance Manual

Dealer Copy -- Not for Resale MST-2 116 of 134

864 Bobcat Loader Operation & Maintenance Manual

Dealer Copy -- Not for Resale

SERVICE SCHEDULE (6734534)

117 of 134

MST-3

864 Bobcat Loader Operation and Maintenance Manual

Dealer Copy -- Not for Resale

WARNING (6718390)

118 of 134

MST-4

864 Bobcat Loader Operation and Maintenance Manual

Dealer Copy -- Not for Resale

WARNING (6718400)

119 of 134

MST-5

864 Bobcat Loader Operation and Maintenance Manual

WARNING (6577754)

Dealer Copy -- Not for Resale

WARNING (6718391)

120 of 134

MST-6

864 Bobcat Loader Operation and Maintenance Manual

DANGER (6718392)

DANGER (6717343)

Dealer Copy -- Not for Resale

DANGER (6718393)

WARNING (6804114)

121 of 134

MST-7

864 Bobcat Loader Operation and Maintenance Manual

WARNING (6718397)

Dealer Copy -- Not for Resale

IMPORTANT (6560573)

122 of 134

MST-8

864 Bobcat Loader Operation and Maintenance Manual

Dealer Copy -- Not for Resale

LIFT ARM SUPPORT DEVICE (6706558)

123 of 134

MST-9

864 Bobcat Loader Operation and Maintenance Manual

Dealer Copy -- Not for Resale 124 of 134

MST-10

864 Bobcat Loader Operation and Maintenance Manual

SPECIFICATIONS 864/864H COMPACT TRACK LOADER SPECIFICATIONS . SPEC-3 Capacities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SPEC-4 Drive System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SPEC-4 Electrical System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SPEC-4 Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SPEC-3 Hydraulic System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SPEC-4 Loader Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SPEC-3 Optional BOSS System Instrumentation . . . . . . . . . . . . . . SPEC-4 Performance Specifications . . . . . . . . . . . . . . . . . . . . . . . . SPEC-3 Standard System Instrumentation . . . . . . . . . . . . . . . . . . . SPEC-4 ADDITIONAL PUBLICATIONS AND TRAINING MATERIALS SPEC-8

Dealer Copy -- Not for Resale

BOBCAT APPROVED ATTACHMENTS & ACCESSORIES . . SPEC-5 Attachments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SPEC-6 Buckets Available. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SPEC-5

SPECIFICATIONS

SPEC-1 125 of 134

864 Bobcat Loader Operation & Maintenance Manual

Dealer Copy -- Not for Resale SPEC-2 126 of 134

864 Bobcat Loader Operation & Maintenance Manual

•

Dimensions are given for loader equipped with standard dirt bucket and may vary with other bucket types. All dimensions are shown in inches. Respective metric dimensions are given in millimeters enclosed by parentheses.

•

Where applicable, specifications conform to SAE or ISO standards and are subject to change without notice.

Changes of structure or weight distribution of the loader can cause changes in control and steering response and can cause failure of the loader parts.

Performance Specifications Rated Operating Capacity (SAE)

2000 lb. (907 kg)

Tipping Load (SAE)

5715 lb. (2592 kg)

Operating Weight

8200 lb. (3719 kg)

Travel Speed

6.7 mph (10,8 km/hr.)

Engine Make/Model

Deutz/BF4M1011F Turbo Charged

Fuel/Cooling

Diesel/Oil

Horsepower (SAE Net)

73.5 HP (55 kW)

Number of Cylinders

Four

Lubrication

Pressure System W/Filter

Air Cleaner

Dry replaceable cartridge w/safety element

Loader Controls Steering

Two hand levers

Loader Hydraulics

Separate foot pedals (or optional hand controls)

Auxiliary Hydraulics

Electrical switches in the steering levers

Parking Brake

Foot operated pedal

127 of 134

SPEC-3

864 Bobcat Loader Operation and Maintenance Manual

Dealer Copy -- Not for Resale

864/864H COMPACT TRACK LOADER SPECIFICATIONS

864/864H COMPACT TRACK LOADER SPECIFICATIONS (CONT’D) Drive System Primary

Hydrostatic track drive

Hydraulic System Engine driven, gear type

18.8 GPM (71,2,0 L/min.) @ 3000 RPM

System relief @ quick couplers

3000 PSI (20600 kPa)

Electrical System Alternator

12-volts, 50 or 90 amp, open, neg. ground

Battery

12 volts - 1000 CCA @ 0°F (-18°C)

Standard System Instrumentation Hourmeter, gauges, and warning lights for engine and hydraulic/hydrostatic functions.

Electronic display panel with visual warning and audible alarm. Automatic shutdown function and diagnostic capability.

Capacities CAPACITIES:

TYPE:

Fuel Tank

25 Gal. (94 L)

Diesel #2 or #1

Eng. Lubrication & Cooling System

16 qt. (9,5 L)

See Chart Page PM-21

Engine Oil Change w/Filter

9 qt. (8.5 L)

See Chart Page PM-21

Hydrostatic Motor Carrier

---

Synthetic Oil P/N 6682546

Idlers and Roller

3.4 oz. (100 cc)

SAE 10W-40

Hyd./Hydros. Res.

4 Gal. (15,2 L)

See Below

Hyd./Hydros. System

10 Gal. (38 L)

See Below

Abv. 0°F (-18°C) use Bobcat Fluid 6563328 or SAE 10W-30 SE, 10W-40 SE Bel. 0°F (-18°C) use SAE 5W-30 SE

128 of 134

SPEC-4

864 Bobcat Loader Operation and Maintenance Manual

Dealer Copy -- Not for Resale

Optional BOSS System Instrumentation

BOBCAT APPROVED ATTACHMENTS & ACCESSORIES These and other attachments are approved for use on this model Bobcat Loader. Do not use unapproved attachments.

Attachments not manufactured by Bobcat may not be approved.

The versatile Bobcat Loader quickly turns into a multi-job machine with a tight-fit attachment hook-up . . . from bucket to grapple to pallet fork to backhoe and a variety or other attachments.

See your Bobcat dealer for more details on the these and other attachments and field accessories.

Increase the versatility of your Bobcat Loader with a variety of bucket styles and sizes.

Dealer Copy -- Not for Resale

Buckets Available Many bucket styles, widths and different capacities are available for a variety of di fferent applications. They include Construction & Industrial, Utility, Fertilizer and Snow, to name a few. See your Bobcat dealer for the correct bucket for your Bobcat Loader and application.

129 of 134

SPEC-5

864 Bobcat Loader Operation and Maintenance Manual

BOBCAT APPROVED ATTACHMENTS & ACCESSORIES (CONT’D)

Dealer Copy -- Not for Resale

Attachments

These and other attachments are approved for use on this model Bobcat Loader. Do not use unapproved attachments.

Attachments not manufactured by Bobcat may not be approved.

130 of 134

SPEC-6

864 Bobcat Loader Operation and Maintenance Manual

BOBCAT APPROVED ATTACHMENTS & ACCESSORIES (CONT’D) Attachments (Cont’d)

Dealer Copy -- Not for Resale

See your Bobcat dealer for more details on these and other attachments and field accessories.

131 of 134

SPEC-7

864 Bobcat Loader Operation and Maintenance Manual

ADDITIONAL PUBLICATIONS AND TRAINING MATERIALS The following publications and training materials are also available for your Bobcat Loader. You can order them from your Bobcat dealer.

For the latest information on Bobcat products and the Bobcat/Ingersoll-Rand, visit our website at www.bobcat.com 6719951

Dealer Copy -- Not for Resale

6900953

132 of 134

SPEC-8

864 Bobcat Loader Operation and Maintenance Manual

WARRANTY Bobcat Loaders Bobcat Company warrants to its authorized dealers and authorized dealers of Bobcat Equipment Ltd., who in turn warrant to the owner, that each new Bobcat loader will be free from proven defects in material and workmanship for twelve (12) months after delivery by the authorized Bobcat dealer to the original buyer.

This warranty does not apply to diesel engine fuel injection pumps and injectors or tires (except Bobcat brand tires). The owner shall rely solely on the warranty, if any, of the respective manufacturers thereof. This warranty does not cover replacement of scheduled service items such as oil, filters, tune-up parts, and other high-wear items. This warranty does not cover damages resulting from abuse, accidents, alterations, use of the Bobcat product with any accessory or attachment not approved by Bobcat Company, air flow obstructions, or failure to maintain or use the Bobcat product according to the instructions applicable to it.

THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES AND CONDITIONS, EXCEPT THE WARRANTY OF TITLE. BOBCAT COMPANY DISCLAIMS ALL OTHER WARRANTIES AND CONDITIONS, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL BOBCAT COMPANY OR THE AUTHORIZED BOBCAT DEALER BE LIABLE FOR ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES WHATSOEVER, INCLUDING, BUT NOT LIMITED TO, LOSS OR INTERRUPTION OF BUSINESS, LOST PROFITS, OR LOSS OF MACHINE USE, WHETHER BASED ON CONTRACT, WARRANTY, TORT, NEGLIGENCE, STRICT LIABILITY, STATUTE OR OTHERWISE, EVEN IF BOBCAT COMPANY OR THE AUTHORIZED BOBCAT DEALER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE TOTAL LIABILITY OF BOBCAT COMPANY AND THE AUTHORIZED BOBCAT DEALERS WITH RESPECT TO THE PRODUCT AND SERVICES FURNISHED HEREUNDER SHALL NOT EXCEED THE PURCHASE PRICE OF THE PRODUCT UPON WHICH SUCH LIABILITY IS BASED.

6570162 (11-00)

133 of 134

Printed in U.S.A.

Dealer Copy -- Not for Resale

During the warranty period, the authorized Bobcat dealer shall repair or replace, at Bobcat Company's option, without charge for parts and labor, any part of the Bobcat product which fails because of defects in material or workmanship. The owner shall provide the authorized Bobcat dealer with prompt written notice of the defect and allow reasonable time for repair or replacement. Bobcat Company may, at its option, require failed parts to be returned to the factory. Travel time of mechanics and transportation of the Bobcat product to the authorized Bobcat dealer for warranty work are the responsibility of the owner. The remedies provided in this warranty are exclusive.

134 of 134

Dealer Copy -- Not for Resale