Bomag Mph 362 364 2 Recycler And Stabilizer Workshop Service Repair Manual Download

MPH362_364-2 0852738 CVR

1/16/06

3:13 PM

Page 1

Instructions For Repair

MPH 362/364-2 S//N 901B23001601> S Cummins QSM 11 360HP Cu

Soil Stabiliz er/Asphalt Recycler

Printed in U.S.A.

BOMAG Americas, Inc. 2000 Kentville Rd. Kewanee, IL 61443

0852738

01/01/06

MPH 362-2 - MPH 364-2 RECYCLER - STABILIZER DANGER:

08/05

If the machine was received with the Roll Over Protective Structure (ROPS) or Roll Over/Falling Object Protection System (ROPS/FOPS) and Operator Restraint (Seat Belt) NOT installed, both MUST be installed BEFORE the machine is operated. Use the installation instructions drawing included with the installation kit and/or the illustration below.

In the event of a machine roll over, serious injury, or death, can occur due to the failure to correctly install the Roll Over Protective Structure (ROPS) or Roll Over/Falling Object Protection System (ROPS/FOPS) and the Operator Restraint (Seat Belt).

DANGER:

DO NOT operate machine with Roll Over Protective Structure (ROPS) or Roll Over/Falling Object Protection System (ROPS/FOPS) and/or Operator Restraint (Seat Belt) NOT properly installed.

i

ii

08/05

CLICK HERE TO

DOWNLOAD THE COMPLETE MANUAL

• Thank you very much for reading the preview of the manual.

• You can download the complete manual from: www.heydownloads.com by clicking the link below

• Please note: If there is no response to CLICKING the link, please download this PDF first and then click on it.

CLICK HERE TO

DOWNLOAD THE COMPLETE MANUAL

SYMBOLS USED IN THIS MANUAL The following symbols have been used in this manual to help communicate the intent of the instructions. When one of these symbols appears, it conveys the meaning as defined in the following descriptions:

DANGER:

Serious personal injury, death and/or extensive property damage can result if the DANGER instructions are not followed.

Serious personal injury and/or extensive property damage can result if the WARNING instructions are not followed.

08/05

Minor personal injury can result, or a part, an assembly, or the engine can be damaged if the CAUTION instructions are not followed.

NOTE: Gives additional information, and/or clarification details, which are used in conjunction with previously presented information.

iii

Safety Regulations SAFETY SAFETY REGULATIONS

•

INTRODUCTION The following safety regulations apply to all personnel engaged in the operation, maintenance or repair of this machine.

Intended Use The machine is available in both Recycler and Stabilizer configurations. As a Recycler, the machine is intended for use in recycling bituminous surfaced roadways and paved surfaces using recycling teeth mounted on the rotor. When configured as a Stabilizer the machine is intended to stabilize soil, using paddles mounted on the rotor. Only authorized and trained personnel can operate this machine.

The potential for damage to the machine or injury to personnel exists if this machine is used for purposes other than those for which it was designed, or if it is used by personnel not familiar with information contained in this manual.

General

•

Make certain you are familiar with all controls and accessories on the machine.

•

Do not operate the machine unless you are trained on all operating and control features and know how the machine functions.

•

Familiarize yourself with the work area including surface and subsurface conditions, vegetation, water tables and other indications of conditions that may be encountered during operation.

•

Use the machine only for the purpose for which it is intended.

•

Wear protective clothing such as safety helmet, protective shoes, noise protection and eye protection.

•

Original parts and accessories have been specifically designed for this machine. Unauthorized conversions and alterations to the machine or its component parts or assemblies are prohibited as they may endanger safe operation.

iv

The factory has not tested or authorized any component parts or special equipment not supplied by the factory. The installation or use of unauthorized products can have an adverse effect on design characteristics and influence active or passive operating safety.

The manufacturer expressly excludes any liability for damages, actual or consequential, resulting from the use of non-factory approved parts or accessories on this machine.

•

Should the machine contact high voltage power lines: – Move the machine out of the danger zone, if at all possible.

– Do not leave the operator’s platform.

– Alert and warn others to move away from the machine.

– Request electric utility shut down electrical power.

DANGER:

Use EXTREME caution whenever anyone is working inside the wheels on the steering (front) axle.

Serious, or fatal, injuries can result from the wheels being turned while a worker is inside this area. NEVER turn the steering wheel, release the brakes, or engage the hydrostatic drive(s) while someone is working in this area.

DANGER:

Exhaust fumes are dangerous.

Ensure an adequate supply of fresh air when starting up in enclosed spaces or vent the vehicle exhaust outside through an approved exhaust system.

08/05

Safety Regulations SAFETY Prior to Starting

Operation

•

Review operating instructions before starting the engine.

•

•

Press the Emergency Stop push button immediately in emergencies and potentially dangerous situations.

Check the machine and controls for obvious faults.

•

The machine may only be operated from the operator’s seat.

Do not drive or operate the machine with damaged instruments, control lights or control elements or systems.

•

Before starting work, check that controls, lighting and horn are operating properly.

•

Before starting or resuming work, you must make sure no one is in the danger area surrounding the machine.

• •

All protective devices must be properly secured in their locations.

•

Do not leave any loose objects such as tools or personal items such as lunch boxes lying about.

Secure or store such objects in a safe manner.

•

Keep the machine free from all oily or combustible materials.

•

Before climbing onto the machine, make sure there are no persons or obstacles near or under the machine.

– You must give a warning signal.

– Stop work immediately if persons remain in the danger area despite the warning.

•

When driving in reverse, make sure that no one or any obstacles are in the way.

•

Control the speed of the machine to working conditions.

•

Keep the machine away from edges and embankments.

•

When driving under a flyover, bridge, power lines, through a tunnel, etc. make sure there is sufficient clearance.

Starting

•

Use lighting whenever visibility is poor.

•

Ensure all controls are in the “neutral” position when starting the engine.

•

•

Only start and operate the machine from the operator’s seat.

If a slope must be traversed, drive very carefully and always drive directly up or down the slope (never on an angle). Select the lower travel speed range whenever approaching a slope.

•

Check all indicators after start-up to ensure all systems are operating correctly.

•

Soil conditions and weather influences reduce the ability of the machine to climb or descend grades.

•

Never leave a machine unattended while the engine is running.

•

•

For emergency starting using jumper cables from an external power source, connect positive to positive and negative to negative. Always connect the ground wire (negative) last and disconnect the ground wire first. This is a 24 volt sytem.

Wet and loose soils considerably reduce machine ground traction on grades. It also increases the danger of accidents.

•

Never climb on the machine while it is in motion.

•

The machine may never be used as a transport for personnel, or equipment.

•

Use care when climbing onto the machine.

Always use the steps and handrails provided.

•

Adjust the seat before starting the engine.

•

Always use the seat belt provided on machines with ROPS/FOPS or ROPS structures.

08/05

v

Safety Regulations SAFETY •

All handrails, steps and platforms are to be kept free of grease, oil, fuel, dirt, snow and ice.

•

Should the machine develop an unusual noise or generate smoke while operating the machine, stop the engine, trace the cause, and have any faults corrected.

•

Never adjust the operator’s seat while the machine is in motion.

•

Do not use the emergency stop push button as an operating brake.

Parking

•

Before leaving the machine, set the Travel Direction Control Lever (FNR) to “neutral”, apply the parking brake and stop the engine.

•

Park the machine on level and firm ground.

•

Never jump off the machine. Use the access steps and hand rails.

•

If you must park on an incline, set wedges in front of, or behind, the tires.

Maintenance

•

For repairs and maintenance work, place the machine on firm and level ground.

•

Do not perform any adjustments while the engine is running or machine is being driven.

•

Keep unauthorized persons away from the machine whenever performing maintenance work.

•

Identify a machine with problems by attaching a warning sign to the steering wheel.

•

Before starting engine, check that the battery disconnect switch is in the ON position.

•

Whenever refueling or working with the fuel system: – Only refuel while the engine is stopped.

– Observe cleanliness.

– Do not spill any fuel.

•

Petrol-diesel mixtures (winter fuel) are as flammable as standard diesel fuel mixtures.

•

Do not refuel in enclosed spaces.

•

Place used filters in a specially marked container and dispose of them in an approved manner to prevent pollution.

•

During maintenance work, collect oils and fuels and dispose of them carefully to prevent pollution. Be aware there is a danger of scalding when working with hot oil.

•

Do not heat oil to a temperature over 320°F (160°C) otherwise oil, or oil vapor, may ignite.

•

Wipe away any fuel, or oil, which has been spilled.

•

Never smoke when filling the fuel tank or checking acid level of the batteries.

•

Never check acid level of the batteries or fuel level with an open flame.

Loading and Transport

•

Use only strong and stable loading ramps when loading the machine. Make sure no one is endangered in the event the unit accidentally turns over or slips during the loading process.

•

Ramp incline must be lower than the machine’s ability to climb or gradability.

•

Secure the machine on the transport vehicle using the attachment points provided. (See Transportation Data – Section 3.) This action will guard against the machine rolling, slipping or turning over.

• •

vi

Do not step or stand under lifted loads. This constitutes a danger to life.

Do not stand in danger areas of the machine during operation, demonstrations or loading. This constitutes a danger to life.

08/05

Safety Regulations SAFETY •

Dispose of used batteries carefully to prevent pollution.

•

Never perform cleaning work with the engine running.

•

Use caution when working with cleansing agents.

Gasoline, or other easily flammable substances, must never be used for cleaning purposes.

•

Cover electric parts with watertight insulating material when using a steam cleaner. Never subject these parts to a direct water jet.

•

Visually inspect hydraulic hoses at regular intervals.

•

Check to ensure hydraulic lines are depressurized before disconnecting them. Hydraulic oil, escaping under pressure, can penetrate your skin and cause serious injury.

•

When performing adjustments to the hydraulic system, never step behind or in front of the machine.

• • •

Never attempt to adjust pressure relief valves.

These are factory set.

While the system is depressurized, check all connections and fittings for leaks when all maintenance work has been completed.

Refit all protective devices when all maintenance work has been completed.

Repair

•

Repairs to this machine may only be performed by skilled and trained personnel.

•

Use only Bomag Americas approved repair procedures.

•

Observe any special welding instructions when performing welding work.

ROPS/FOPS or ROPS Structure Inspection

•

The machine frame must not be bent, deformed or cracked in the area of the ROPS/FOPS or ROPS installation.

•

The ROPS/FOPS or ROPS structure must not show rust, damage, hairline cracks or open fractures.

•

The ROPS/FOPS or ROPS structure must not rattle when the machine is being driven.

•

All screw connections must be in accordance with manual specifications and must be secure (observe tightening torques).

•

Screws and nuts must not be damaged, bent or deformed.

•

No additional parts may be welded or screwed, and no additional holes may be drilled without the approval of the manufacturer. Unauthorized alterations may influence stability and safe operation.

NOTE: Following the lubrication and maintenance schedules, and the operating instructions will help to ensure that your machine has a long service life and is always fully operational.

08/05

vii

Safety Regulations SAFETY

viii

08/05

Section 1 INTRODUCTION

TABLE OF CONTENTS

PAGE

GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2 TECHNICAL DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2 SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-3 OPERATING INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-3 MAINTENANCE PROCEDURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-3 NAMEPLATE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-3 SERIAL NUMBER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-4

08/05

1-1

Section 1 INTRODUCTION GENERAL INFORMATION. This manual contains OPERATING procedures for BOMAG Recyclers & Stabilizers. (See Figure 1-1).

• • •

TECHNICAL DATA. Standard Equipment.

• • • • • • • • • • • •

Hydrostatic rotor drive with engine load control Hydrostatic travel system Rear axle - hydraulic motors/planetary gearbox with Spring Applied Hydraulically Released (SAHR) brakes - each wheel ASC (electronic traction control) Selectable hydrostatic front drive axle (MPH 364-2 ONLY) Hydraulic power steering Hydrodynamic service brakes Single lever control travel and steer assist braking 24V electrical system with manual battery disconnect Dual element engine air filter Warning horns Emergency stop

• • • • •

Back-up alarm Gauges - Rotor drive pressure - Travel drive pressure PowerView Monitoring and Display System - Fuel level - Hour meter - Voltmeter - High engine coolant temperature - High hydraulic oil temperature - Low engine oil pressure - Low rotor charge pressure - Engine inlet air - restriction - Hydraulic oil filters - restriction - Engine tachometer (RPM) - Feet per minute (FPM)/Speedometer (MPH) Visual warning indicators - Brakes applied Audible warning buzzers - Sounded in conjunction with PowerView monitoring and display system ROPS/FOPS with seat belt, or ROPS with seat belt Adjustable operator’s seat Adjustable tilt steering wheel

FIGURE 1-1. BOMAG RECYCLER – WITH ROPS/FOPS. 1-2

08/05

Section 1 INTRODUCTION SPECIFICATIONS.

NAMEPLATE (SEE FIGURE 1-2).

See Section 2 – SPECIFICATIONS in this manual for specifications of major systems used on the machine.

The nameplate is found in the operator’s control station on the firewall plate near the engine throttle control.

OPERATING INSTRUCTIONS. Read, understand and follow ALL operating instructions given in Section 3 – OPERATION in this manual - and in the Cummins QSM11 “Operation and Maintenance Manual”, supplied with the machine.

BOMAG TYPE

MAINTENANCE PROCEDURES. See Section 4 – MAINTENANCE, in this manual, for maintenance schedules and procedures that are required for the major systems of this machine.

Follow ALL maintenance schedules and procedures given in this manual and in the Cummins QSM11 “Operation and Maintenance Manual”, supplied with the machine.

08/05

BETRIEBSGEWICHT OPERATING WEIGHT POIDS DE SERVISE 39,000 lbs (17706 kg)

NO

Only authorized personnel, who are fully trained in the machine operation procedures, can operate the BOMAG Recycler or Stabilizer.

Follow all instructions given in this manual and written on the “Machine Operation and Warning” decals, found on the machine.

MPH364R

901B2301601

KG

MAX. GEWICHT MAX. WEIGHT POIDS MAX.

KG

MANUFACTURED BY

BOMAG Americas KEWANEE, ILLINOIS, USA MANUFACTURED UNDER ONE OR MORE OF THE FOLLOWING U.S. PATENTS: 5645370, 5248216, 5797699

30100007

FIGURE 1-2. NAMEPLATE. The nameplate shows the machine manufacturing plant code, model number code and serial number.

The nameplate must stay fastened to the machine at all times. If the nameplate is lost or damaged, it must be replaced immediately.

Consult your nearest BOMAG Distributor to obtain a replacement nameplate and install it immediately.

1-3

Section 1 INTRODUCTION SERIAL NUMBER (See Figures 1-2 and 1-3 and Table 1-1).

•

The manufacturing plant code, machine model number code, and serial number are found stamped on the nameplate located in the cockpit. (See Figure 1-2). The complete machine serial number is, also, stamped at two other locations on the machine (See Figure 1-3).

To help ensure correct information, or parts, are obtained for the BOMAG Recyclers and Stabilizers, ALWAYS supply the complete model number and the serial number whenever requesting ANY information, or ordering ANY machine parts.

•

On top of the frame, beneath the bolt on cover for the front ballast compartment.

The top of the frame rail in the engine compartment on the right hand side of the unit.

SERIAL NUMBER LOCATIONS TOP OF CROSS PIECE ON BALLAST - BENEATH FRONT COVER

TOP OF FRAME RAIL ON THE UNIT S/N PLATE IN THE COCKPIT

FIGURE 1-3. STAMPED SERIAL NUMBER LOCATIONS.

901

PLANT OF MANUFACTURE CODE

B230

UNIT CODE

1601

MACHINE SERIAL NUMBER

TABLE 1-1. SERIAL NUMBER DESIGNATIONS.

1-4

08/05

Section 2 SPECIFICATIONS

TABLE OF CONTENTS

PAGE

GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-2 TABLE 2-1. ENGINE SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-2 TABLE 2-2. ENGINE INLET AIR FILTRATION SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-3 TABLE 2-3. ELECTRICAL SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-3 TABLE 2-4. TRANSMISSION AND FINAL DRIVE SYSTEM SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . .2-4 TABLE 2-5. BRAKE SYSTEM SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-5 TABLE 2-6. STEERING SYSTEM SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-5 TABLE 2-7. ROTOR SYSTEM SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-6 TABLE 2-8. DIMENSION SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-8 TABLE 2-9. WEIGHT SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-9 TABLE 2-10. CAPACITY SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-9

08/05

2-1

Section 2 SPECIFICATIONS GENERAL INFORMATION. This section provides specification tables for major systems of the BOMAG Recycler or Stabilizer.

Dimensions, weights and performance specifications are also provided.

TABLE 2-1. ENGINE SPECIFICATIONS. ITEM

MPH 362-2 - 364-2

ENGINE

2-2

Manufacturer

Cummins

Model

QSM11- Turbocharged & charge air cooled

Cooling

Water

Type

4 Cycle Diesel

Number of Cylinders

6

Firing Order

1-5-3-6-2-4

SAE Net Horsepower

360 hp (268.3 kW) @ 2100 RPM

Torque

900 ft•lbs (1220 N•m) @ 2100 RPM

Fuel

Diesel

Fuel Viscosity

1.3 cSt

Fuel Consumption Rate

19.2 Gal/hr (72.7L/hr) @ 2100 RPM

Compression Ratio

16.3 : 1

Displacement

660 C.I.D. (10.8 liters)

Bore

4.921 in (125 mm)

Stroke

5.787 in (147 mm)

Crankshaft Rotation (Viewed from engine front)

Clockwise

High Idle Speed w/o Load

2100 RPM, Loaded, 2300 RPM not loaded

Low Idle Speed

850 RPM

08/05

Section 2 SPECIFICATIONS TABLE 2-2. ENGINE INLET AIR FILTRATION SPECIFICATIONS. ITEM

MPH 362-2 - 364-2

AIR CLEANER Type

Dry, cycloflow w/secondary element & evacuator valve

Manufacturer

Donaldson

Model

FVG 16-0587

RESTRICTION INDICATOR Type

Electrical / visual resetable

Manufacturer

Donaldson

Model

Electrical Indicator / Informer

TABLE 2-3. ELECTRICAL SPECIFICATIONS. ITEM

MPH 362-2 - 364-2

BATTERY Number per Machine

2

CCA Rating

1,000 CCA @ 0°F

Voltage

24 VDC System (Two 12 Volt batteries in series)

BCI Group

Group 4D-P

ALTERNATOR Manufacturer

See alternator plate for manufacturer and part number

Voltage

24 Volts, negative ground

Maximum Charge Rate

70 Amps

STARTER

08/05

Manufacturer

See starter plate for manufacturer and part number

Voltage

24 Volt

2-3

Section 2 SPECIFICATIONS TABLE 2-4. TRANSMISSION AND FINAL DRIVE SPECIFICATIONS. ITEM

MPH 362-2 - 364-2

TRACTION SYSTEM Type

Hydrostatic (closed loop)

Traction Pump

Variable displacement, axial piston

Traction Motors

Rear: Variable, bent axis piston Front: Radial piston(MPH 364-2 ONLY)

TRANSMISSION (FRONT AXLE MPH 364, MPH 364 WIDE ONLY) Manufacturer

Fluidrive

FINAL DRIVE Manufacturer and Type

L&S - GFT 40 T2 9000

Travel Speed Range 1 (Working)

2.1 MPH (3.4 km/h) = 171 FPM (52.1 m/min)

Range 2 (Transport ONLY)

11.0 MPH (17.7 km/h)

Tire Size (Front)

14.9 x 24 8 PR R-1

Tire Inflation Pressure (Front)

35 psi (2.41 bar) cold

Wheel Nut Torque (Front)

400 ft•lbs (542 N•m)

Tire Size (Rear)

28 LR x 26-165LI

Tire Inflation Pressure (Rear)

35 psi (2.41 bar) cold

Wheel Nut Torque (Rear)

426 ft•lbs (578 N•m)

ITEM

MPH362RW-2-364SW-2 MPH362SW-2-364-SW-2

Travel Speed

2-4

Range 1 (Working)

2.1 MPH (3.4 km/h) = 171 FPM (52.1 m/min)

Range 2 (Transport ONLY)

11.0 MPH (17.7 km/h)

Tire Size (Rear)

26.5 x 25 20PR E-2/L-2+2

Tire Inflation Pressure (Rear)

50 psi (3.44 bar) cold

08/05

Section 2 SPECIFICATIONS TABLE 2-5. BRAKE SYSTEM SPECIFICATIONS. ITEM

MPH 362-2 - 364-2

SERVICE BRAKE Type

Hydrodynamic, through hydrostatic travel drive

PARKING BRAKE Type

SAHR (Spring Applied Hydraulically-Released)

EMERGENCY BRAKE Type

SAHR (Spring Applied Hydraulically-Released)

TABLE 2-6. STEERING SYSTEM SPECIFICATIONS. ITEM

MPH 362-2 - 364-2

STEERING SYSTEM

08/05

Type

Axle pivot

Method

Hydraulic, through orbitol

Steering Angle

+/- 30 Degrees

Inside Turning Radius

252 in (6401 mm)

2-5

Section 2 SPECIFICATIONS TABLE 2-7. ROTOR SYSTEM SPECIFICATIONS. ITEM

MPH 362-2 - 364-2

ROTOR SYSTEM Type

Hydraulic, closed loop

Pump Quantity

1

Pump Type

Variable displacement, axial piston

Motor Quantity

2

Motor Type

Radial piston

ROTOR

2-6

Recycler

Stabilizer

Rotor Diameter (Outer)

30 in (762 mm)

30 in (762 mm)

Rotor Circle Diameter (Outside Cutting Teeth)

44 in (1118 mm)

48 in (1219mm) 59.5 in (1511 mm) - Deep Mix

Cutting Width

79 in (2007 mm)

79 in (2007 mm)

Maximum Cutting Depth

12 in (381 mm)

14 in (356 mm) 21 in (533 mm) - Deep Mix

Rotor Speed

I = 135

I = 135

II = 150

II = 150

Sense of Rotation

Up-cut

Up-cut, or down-cut

Type of Cutting Teeth

Carbide tipped bullet tooth knock in/knock out

Carbide faced paddle knock in/knock out

Quantity of Teeth

168

70

Height of Cutting Tooth

7 in (178mm)

9 in (229 mm)

Rotor Hood Width

101 in (2565 mm)

101 in (2565 mm)

Cutting Chamber Width

83.75 in (2127 mm)

83.75 in (2127 mm)

08/05

Section 2 SPECIFICATIONS TABLE 2-7. ROTOR SYSTEM SPECIFICATIONS (CONTINUED).

ITEM

MPH362RW-2-364SW-2 MPH362SW-2-364-SW-2

ROTOR SYSTEM Type

Hydraulic, closed loop

Pump Quantity

1

Pump Type

Variable displacement, axial piston

Motor Quantity

2

Motor Type

Radial piston

ROTOR

08/05

Recycler

Stabilizer

Rotor Diameter (Outer)

34 in (864 mm)

34 in (864 mm)

Rotor Circle Diameter (Outside Cutting Teeth)

48 in (1219 mm)

48 in (1219 mm)

Cutting Width

96 in (2438 mm)

96 in (2438 mm)

Maximum Cutting Depth

15 in (381 mm)

15 in (381 mm)

Rotor Speed

I = 135

I = 135

II = 150

II = 150

Sense of Rotation

Up-cut

Up-cut, or down-cut

Type of Cutting Teeth

Carbide tipped bullet tooth knock in/knock out

Carbide faced paddle knock in/knock out

Quantity of Teeth

196

82

Height of Cutting Tooth

7 in (178mm)

7 in (178mm)

Rotor Hood Width

118 in (2997 mm)

118 in (2997 mm)

Cutting Chamber Width

100.75 in (2559 mm)

100.75 in (2559 mm)

2-7

Section 2 SPECIFICATIONS TABLE 2-8. DIMENSION SPECIFICATIONS. ITEM

MPH 362-2 - 364-2

Dimensions (see Figure 2-1) A. Overall Length

331 in (8407 mm)

B. Overall Width

115 in (2921 mm)

C. Overall Height – With ROPS or ROPS/FOPS

138 in (3505 mm)

D. Overall Height - With Cab

138 in (3505 mm)

E. Height To Top Of Exhaust Pipe

136 in (3454 mm)

F. Height To Top Of Cockpit Handrail

111 in (2819 mm)

G. Wheelbase

129 in (3277 mm)

H. Ground Clearance

19 in (483 mm)

I. Working Width - Rotor

79 in (2007 mm)

I. Working Width - Rotor With Wide Rotor Option

96 in (2438 mm)

C/D

E F

H G

I A

B

FIGURE 2-1. BOMAG MPH 362-2 AND 364-2 RECYCLER/STABILIZER – DIMENSIONS.

2-8

08/05

Section 2 SPECIFICATIONS TABLE 2-9. WEIGHT SPECIFICATIONS. ITEM

MPH 362-2

MPH 364-2

Weights Operating Weight

39,000 lbs. (17,706 kg.)

39,000 lbs. (17,706 kg.)

Axle Load – Front

10,920 lbs. (4,958 kg.)

10,920 lbs. (4,958 kg.)

Axle Load – Rear

28,080 lbs. (12,749 kg.)

28,080 lbs. (12,749 kg.)

% Weight Distribution – Front/Rear

25% / 75% - Approximate

25% / 75% - Approximate

ITEM

MPH362RW-2-364SW-2 MPH362SW-2-364-SW-2

Weights Operating Weight

45,300 lbs. (20,540 kg.)

Axle Load – Front

12,005 lbs. (5,445 kg.)

Axle Load – Rear

34,294 lbs. (15,101 kg.)

% Weight Distribution – Front/Rear

25% / 75% - Approximate

TABLE 2-10. CAPACITY SPECIFICATIONS. ITEM

MPH 362-2 - 364-2

Capacities

08/05

Fuel

260 Gal. (984 liters), Total capacity (BOTH tanks full)

Hydraulic Oil

90 Gal. (341 liters), Reservoir only

Engine Oil

9.8 Gal. (37.4 liters)- including engine mounted filter

Engine Coolant

78.0 Quarts (74 Liters), Total system

2-9

CLICK HERE TO

DOWNLOAD THE COMPLETE MANUAL

• Thank you very much for reading the preview of the manual.

• You can download the complete manual from: www.heydownloads.com by clicking the link below

• Please note: If there is no response to CLICKING the link, please download this PDF first and then click on it.

CLICK HERE TO

DOWNLOAD THE COMPLETE MANUAL