Technical Manual
• Thank you very much for reading the preview of the manual.
• You can download the complete manual from: www.heydownloads.com by clicking the link below
• Please note: If there is no response to CLICKING the link, please download this PDF first and then click on it.
M-3
BLAST HOLE DRILL MAINTENANCE AND OPERATION.
This manual is divided into major sections covering various serviceable components and systems of the Rotary Blast Hole Drill. These sections and their contents are organized by thumb index tabs shown below and right - blue ink tab marks. To use this manual, grasp the right hand side of the book between thumb and fingers. Bend pages back to find the start of the corresponding sections in this index tab.
SECTION 1- INTRODUCTION
SECTION 2- OPERATION
SECTION 3- MECHANICAL ADJUSTMENT
SECTION 4- HYDRAULIC SYSTEMS
SECTION 5- DRILL AIR SYSTEMS
SECTION 6- AUXILIARY AIR SYSTEM
SECTION 7- LUBRICATION
SECTION 8- ENGINEERING DATA
SECTION 9- ELECTRICAL
seCTION 10 - INSPECTION REPORTS
SECTION 1
INTRODUCTION
GENERAL INFORMATION
This manual is designed to assist the owner in the operation and preventive maintenance of this machine. Following easy to understand step-by-step procedures, maintenance personnel can perform these tasks in a safe manner. When a systematic and thorough maintenance/ service procedure (a responsibility of the maintenance superintendent) is used for this machine, minimum unplanned downtime and reliable operation will result.
THIS MANUAL IS NOT THE PARTS BOOK, and cannot be used to order parts. A separate, detailed parts book has been supplied. Please carefully read the instructions in it. All parts are listed by group and/or product code numbers with item/part numbers for THIS SPECIFIC MACH INE. Order parts in exact quantity. Parts ordered by mistake and returned, are subject to a rehandling charge. RIGHT and LEFT HAND PARTS on the upper frame correspond to the operator's hands at the controls; as seated when operating the machine. Please state the correct machine SERIAL NUMBER (located on a plate in the operator's cab) when corresponding or contacting factory service or parts departments. Records on each machine are filed by serial number and when given this number, your machine's specific design and original equipment is accessed quickly by the Marion parts representative.
Periodic additions or revisions may be made to this manual. These will be mailed direct to you from the factory. Should you require additional information or factory service assistance contact your regional service representative or
Service Department
Marion Power Shovel Division
Dresser Industries, Inc.
617 West Center Street
P.O. Box 505
Marion, OH 43302
or:
Telephone 614/383-5211
Telex 24-5307
TWX 810/487-2772
Telecopier 614/383-5211
It is Marion Power Shovel Division policy to improve its products whenever possible and practical to do so. Marion reserves the right to make changes or add improvements at any time without incurring any obligation to install such changes on machines sold previously.
Due to this continu.ous program of product research and development some procedures, specifications and parts may be altered in a constant effort to improve machines. 1-1
SAFETY PRECAUTIONS
This safety alert symbol is used here and throughout this manual to call your attention to instructions concerning your personal safety. Carefully read and follow these instructions and observe all safety and danger, warning and caution graphics mounted on various areas of the machine.
Be certain anyone servicing this machine is aware of these SAFETY PRECAUTIONS. In the event you question your abil ity to safely perform any of the enclosed maintenance and operationalprocedures contact your regional Marion service representative 'Or the factory.
The following defines distinctions between safety instructions. In all these definitions the safety alert signal is used.
DANGER: Denotes extreme intrinsic hazard which exists and could result in high probability of death or irreparable injury if proper precautions are ignored.
WARNING: Denotes a hazard exists which can result in injury or death if proper precautions are ignored.
ACAUTION: Denotes a reminder of safety practices or directs attention to unsafe practices which could result in personal injury if proper precautions are ignored.
An example of a safety alert symbol and special safety instructions is shown below.
DANGER: Inherent danger exists in the operation of any high voltage electrical equipment. A safe grounding system includes ground conductors in the power cable, a neutral grounding resistor and related relays and switchgear. A ground continuity check system is required by law in many parts of the world.
Operating, maintaining or servicing this machine can be dangerous unless performed properly. Each person must satisfy himself and his employer that he is alert and has the necessary skill and information, proper tools and equipment, and all methods are safe and correct. Factory service representatives and specialists are available to provide additional information or technical assistance. 1-2
SAFETY PRECAUTIONS - continued
The operator must be alert, physically fit, and free from the influence of alcohol, drugs, or medications that might effect his eyesight, hearing or reactions.
Safety must always be the operator's most important concern. He must refuse to operate when he knows it is unsafe, and consult his supervisor when safety is in doubt.
The owner and/or operator must replace any and all safety and warning product graphics if they are defaced or removed from the machine.
B·efore doing any work on the machine, lock out or remove electric power supply from the machine and tag it so personnel are aware that someone is working on the machine.
Do not start an engine indoors unless adequate exhaust ventilators are provided. Once an engine is running, move the machine outdoors as soon as possible.
Keep hands, feet, clothing away from rotating parts.
Read carefully this manual, the parts book and manuals provided.
Think before you act. Carelessness is one luxury the serviceman cannot afford.
Do not wear rings, wrist watches or loose fitting clothing when working on machinery. They could catch on moving parts causing serious injury. Never adjust and/or service a machine in bare feet, sandals or sneakers.
Always wear safety glasses when using a hammer, chisel or other tools that may cause chips to fly.
Excessive or repeated skin contact with sealants or solvents may cause skin irritation. In case of skin contact, remove sealant or solvent promptly by washing with soap and water.
Always use a safety bar to block air or hydraulic operated cylinders. Never rely on the machine air or hydraulic systems to hold when working on machines. An air or hydraulic line or cylinder could fail or someone could accidently strike the control levers causing the equipment to fall.
Equipment must be level on ground at all times during machine servicing and periods of idleness.
Cranes and hoists must be of sufficient capacity to I ift the heavier components (gear cases, dipper/bucket, boom, etc.) and have an ample safety margin. 1-3
SAFETY PRECAUTIONS - continued
Be sure heavy items are properly supported from cranes or hoists before removing supporting members from machine.
Have sufficient service personnel available when removing or installing large heavy items to maintain control at all times.
Always use safety stands in conjunction with hydraulic jacks or hoists. Do not rely on the jack or hoist to carry the load, they could fail.
Use safety catch on all hoist hooks. Do not take a chance, the load could slip off of the hook.
If a heavy item begins to fall, let it fall, don't try to catch it.
When disassembling machines, be sure to use safety stands and adequate cribbing to prevent tipping or rollover of components.
Keep work area organized and clean. Wipe up oil or spills of any kind. Keep tools and parts off of the ground. Eliminate the possibility of a fall which could result in a serious injury.
Floors, walkways and stairways must be clean and dry. After draining operations be sure all spillage is cleaned up. Electrical cords and wet metal floors make a dangerous combination.
Check all wire ropes.for telltale signs of early wear or failure. Look for and secure any loose bolts or locking devices.
Use extreme caution while working near any eleetricallines or equipment whether it be high or low voltage. Never attempt electrical repairs unless qualified. Check limit switches for proper operation.
When using an acetylene torch, always wear welding goggles and gloves. Keep a "charged" fire extinguisher within reach. Be sure the acetylene and oxygen tanks are separated by a metal shietd and are chained to the cart. Do not weld or heat areas near transformers or electrical cabinets and utilize proper shielding around lubrication lines.
Use pullers to remove bearings, bushings, gears, cylinder sleeves, etc. when applicable. Use hammers, punches and chisels only when absolutely necessary. Then, be sure to wear safety glasses.
Be careful when using compressed air to dry parts. Use approved air blow guns, do not exceed 207 kPa (30 psi), wear safety glasses or goggles and use proper shielding to protect everyone in the work area.
1-4
SAFETY PRECAUTIONS - continued
Be sure to promptly reinstall safety devices, guards or shields after adjusting and/or servicing the machine.
After servicing, be sure all tools, parts or servicing equipment are removed from the machine.
Protective eye goggles should be worn at all times when working on the air conditioning system. Work on the air conditioning system only in a well ventilated area.
Wipe away excess lubricants around bearings and gears. Never lubricate parts in motion.
Operate machine on level ground and be continuously aware of clearance when lowering mast.
Do not raise'or lower mast unless gear box is down on bottom stops.
Check pull down chains for early signs of wear that may lead to permanent damage or failure.
Do not allow personnel under any part of the machine when it isin operation.
Use extreme caution while working near any hydraulic lines or components. Never attempt hydraulic repairs unless qualified.
Cleanliness of the hydraulic system is esstential for reliable operation.
PREVENTIVE MAINTENANCE
Machine downtime is costly to owners in lost ore production. All mechanical or electrical cc;>mponents and devices will eventually stop. The task of identifying when this machine shut down cou Id occur is the purpose of preventive maintenance.
AWARNING: Do not perfonn inspection activities while machine i. in operation.
Due to variations in operational wear rates of machine components and machine application conditions, component life cycles are different. A scheduled program of machine inspection with accurate record keeping can identify machine component and their rates of wear.
A continuous careful inspection routine can spot unusual conditions or fatiguing components before a failure occurs. Maintenance, repair and component replacement schedules should conform to scheduled machine shutdowns. If during daily, weekly or monthly inspection routines any part shows wear or distortion beyond expected normal patterns replace them with genuine Marion parts at the next scheduled maintenance interval. The cost of parts is small when compared to unscheduled breakdowns with their resulting lost manhours and machine production.
Machines which operate 24 hours, 7 days per week should have a scheduled 8-hour preven· tive maintenance period each 7·day period. See Section 10 for recommended inspection schedules.
Preventive maintenance inspection procedures listed below are suggested as an example of specific typical inspection activities. Each owner shoo Id establish his own preventive maintenance inspection schedule based on machine application conditions and production cycle.
AWARNING: Maintenance and operating personnel should be aware of mechanical, hydraulic and electrical hazards inherent in servicing this machine.
INSPECTION CHECKLIST
Check condition of roller chain and chain sprockets
Test all hold down bolts with impact wrenches
Check crawler shoes, load rollers and shoe sprocket for wear
Inspect steel structures for cracks
Check auto-lube system for loose or damaged fittings and injector conditions
Inspect rotary gear box alignment in hoist and pull down
ADANGER: Remove electrical power from machine whenever inspection of electrical components is performed. Use extreme care in removing guards and protective devices. 1-6
PREVENTIVE MAINTENANCE - continued
ADANGER: REMOVE ELECTRICAL POWER FROM MACHINE BEFORE PER· FORMING ANY OF THE FOLLOWING INSPECTIONS:
Inspect electrical cabinets; any discol.ored wires or components indicate overheating conditions have occured.
Look for moisture, fungus or mildew in electrical cabinets. If found clean with approved solvents only, or compressed air.
Check all electrical cabinets for messy or torn fasteners, cable armor or grommets, loose insulation
Inspect electrical motors for discolored commutators or worn brushes.
These inspection points are representative of typical preventive maintenance routines. Use Section 10 as a detailed guide for all areas of machine inspection and sugg.ested scheduled periods.
