1 Mechanical characteristics and mechanism
The machine tool can be used for a variety of processing, such as planing, press planing, sawing and so on. It has the advantages of simple operation, easy adjustment, safety and reliability. It can be used in furniture manufacturing, mold processing, construction engineering and home decoration and other fields. The machine tool consists of a sawing mechanism, a planing table, a lifting mechanism, a clutch, a tenoning mechanism, a machine base and a motor. The rotation of the main shaft is driven by the V-belt through the motor. The feed of the planer is realized by the V-belt driving the transmission wheel and the sprocket. When the machine feeds automatically, the feeding rollers run at the same time; the lifting mechanism can be adjusted through the hand wheel, and it is driven by the worm gear mechanism. Basic organization please check FIG.2
1.planer leaning board 2. Front planer 3. handle 4. Switch 5. Motor 6. Supporting round steel7. screw lead 8. Retarding system 9. stand 10. thicknesser lifting hand wheel 11. Clutching andle 12. planer table 13. Rear planer
2 Technical specification
Planning width................................. …350-400mm
Max. planing depth..................................... 3mm
Max. trimming depth................................. 10mm
Dia. of the planner spindle Ø78mm
Speed of saw spindle................................................ 3830rpm
Thicknessing height range …6-200mm
Thicknessing feed speed...................................... 9m/min
Motor power............................................... 2.2KW
Working table size 1500*360mm
Weight................................................. 260~300KG
3 Lathe tool’s transmission system
4 Machine tools’s electric system
The electrical system of this machine tool consists of a single-phase motor and a KO-3 reverse switch; all the lines have been connected before leaving the factory. Before operation, please confirm whether the cables are connected properly, if there is any loose, connect it firmly.
5 Lathe tool’s lubricating system
During the use of the machine tool, the necessary lubrication protection for each moving part is required to ensure the service
the lubricating oil should be kept clean, non-acid, waterfree and free of hard particles.
6 Machine tool’suasge and its saft-technical
1， Transportation rules
During transportation, the machine tool should be packed in wooden boxes to prevent damage; during hoisting, care should be taken to keep the hoisting point aligned with the center of gravity to prevent overweight; carefully open the package to prevent damage to the painted and processed surface.
2， Installation rules
The machine is a light and mobile device, so it can be operated without installation; if installation is required, the 4 bolt holes on the machine leg can be bolted to hard ground or other hard objects.
3， Preparation
After unpacking the machine, please clean and maintain the machine; in order to prevent rust, please apply anti-rust oil to all machined surfaces. Then, check each link part to prevent loosening during transportation; finally, perform necessary lubrication on each part according to the lubrication requirements
4， Operating rules
1. Planing and trimming: the feeding direction should be from the adjustable table to the fastening table. Loosen the table height adjustment handle, then shake the handle and adjust it to a suitable height and lock it tightly, so that a suitable planing and trimming depth can be obtained. To adjust the planer shaft, first loosen the four nutlets in the groove of the planer shaft, then adjust the planer to a suitable height (should be higher than the work surface), and then lock the nut; adjust the other two or three planer blades in sequence height
2. Thicknessing: Adjust the handball of the flat/press planer clutch to the working position, and then turn on the machine to find that the press planer's automatic feeding mechanism will work. According to the thickness you want to process, adjust the height of the planing table by shaking the table adjustment hand wheel. After adjustment, please lock the table.。
5， Maintenance and safe operation
1. The parameters of the circular saw blade should match the parameters of the spindle; The planer blade and the circular saw blade must be sharpened before work to ensure sharpness; Pay attention to the installation direction of the planer blade and the saw blade, and the planer blade should be installed in the Uniform cutting within the circle.
2. The operation of the machine tool must be performed by experienced workers, and only a single operation can be performed at a time and the spindle must be rotated forward and backward; safety guards must be worn during work; if accessories are to be replaced or cleaned, the machine must be shut down.
3. Before operating the machine tool, please read the manual carefully
Note: If you want to drill or open a square hole, the rotation of the main shaft and flat planing operation is different, it should be reversed, please turn the reverse switch to the reverse position.。
6， Installation of machine tool legs
First, install the round steel under the stand, loose nuts on each side, tighten the bolts on the stand, connect the stand and the flank plate. Second, adjust the two inside nuts on the supporting round steel to make the stand and flank meet at right angle, or it can damage the stand. Finally, tighten the two outside nuts on the supporting round steel.
7 Specifications of bearing and chain
Bearing list form 1
NO. item type Inner dia*outer qty Assembling
dia.*width position
1 Bearing 180107 62*35*14 See FIG2
2 Bearing 180205 52*25*15 1 See FIG2
3 Bearing 80202 35*15*11 2 See FIG2
4 Bearing 80203 40*17*12 4 See FIG2
5 Bearing 80103 35*17*10 1 See FIG2
6 Bearing 204 47*20*14 See FIG2
7 Bearing 1204 47*20*14 1 See FIG2
8 Bearing 8208 80*40*18 3 See FIG2
V belt form2
NO. item type Inner perimeter qty Assembling position
1 V belt A 1067 1 See FIG2
2 V belt A 1219 2 See FIG2 Chain form3
NO item Mark Qty Assembling position 1 Chain 12.7*111 1 See FIG2