TRANSPORTATION:
1) Goods always travel upon purchaser's risk.
2) The purchaser must inform the shipper and retailer of any goods damaged during transport indue time, so they may contact the insurance company for reimbursement. Any replacement for the damaged parts and components will be sent to the customer C.O.D (cash on delivery) and the customer must represent the relative invoice to the insurance Company for reimbursement.
PROMPT:
1) Before installation, the manual must be read in details and the operation must be done asregulated strictly.
2) The machine must be operated, adjusted and repaired as regulations in the manual, otherwiseguarantee is invalid.
3) Unmentioned operations in the manual must be done by authorized maintenance technician.
4) Any bad consequence resulting from unreasonable operation or adjustment by unauthorizedoperator is out of our responsibility.
ATTENTION:
The machine is under guarantee within 1 year. Any problem occurred, please offer the information as follow while contacting with the retailer or after-sales service dept.
CAUTION:
RADEK Company has the exclusive right of explaining the manual. With the speedy and creativedevelopment policy, the improvement of the product is still going on and on. We have the right of improving the product described in the manual without previous note. The customized product ofspecial structure is exclusive in the manual.
Chapter 1: Brief introduction
RBS series of manual feeding planer can work on plane, side, slope and chamfering etc. The prolonged worktable makes sure straightness of work piece, so they are widely used in all kinds of processing of furniture, wagon box, model and large work piece.
Chapter 2: Main structure
1. The machine is made up of main body, worktable, foundation, guide plate, blade shaft, motor,drive part, and electrical system.
2. The machine is assembled by the main body and divided structures. The blade shaft is supported by bearing seat in the foundation and the worktable by dovetail and foundation. The planing depth is controlled by front and rear handles. Connected with the bearing seat, width of the guide plate can be changed through nut. The blade shaft and the motor can have optional speed through transmission by different size of pulleys.
Chapter 3: Main technical parameters
Model
RBS-600-PREMIUM
Max planning width 630mm
Max planning depth ≤4mm
Blade amount 4
Spindle cutting dia.
Spindle speed
Motor power
Overall dimensions
Ф105mm
5060r/min
380v*5.5kw
3000*940*1100mm
Net weight 650kg
Chapter 4: Electrical system
The machine is powered with triphase alternating current of 50Hz/380V. On the bottom is equipped with ground terminal and it must be connected firmly. It begins working at the touch of an electromagnetic starter. The value of the thermorelay is optional through the change of the current.
Chapter 5: Adjustment of blade
1. The size of the blades must be the same. And they must be in the same height when being polished.
2. The main spindle rotates at high speed. To keep it in good condition and to avoid vibrating caused by unbalanced inertia, the dynamic balancing measures of the spindle is taken and the weight of the blade pressers, blades and screws is also balanced. So to keep the balance of the spindle, arbitrary change of blades and blade pressers is forbidden. If it has to, the weight of the blades and the blade pressers must be balanced in groups. The disparity of weight among each group must be less than 2g.
3. After all the blades are supported, tighten the bolts little by little crosswise all around. Do not totally fasten one bolt totally at once.
Chapter 6: Adjustment of worktable
Loosen the bolt, turn the handle and then fasten the bolt.
Chapter 7: Testrun
Before using, examine every part carefully. Repair the distorted parts and fasten the loosen screws owing to bruising and collision during transport. Make sure all parts are well lubricated and earth wire connected effectively. Power and switch on to check the directions of blade shaft and feeding. Leave the machine running unload for five minutes. Do not start working until you hear no noise and the temperature of the blade shaft is lower than 60.
Chapter 8: Use and maintenance
1. Often Check the blade assembly, feeding unit and screws and solve the problems in time.
2. Do not start working before making sure the power and voltage meet the specified requirements.
3. The whole machine must be in good condition. Do not start working with any problem.
4. Clean wood dust on the machine completely to keep it clean after each shift.
5. If you don’t use the machine for a long time, the exposed surface should be coated withantirust oil. Cover it with waterproof cloth.
6. Power off after the machine stop running and then do examination or maintenance.
7. Set down the period of maintenance according to the using condition.
Chapter 9: Lubrication
Appropriate amount of lubricant should be added to each part for good condition and long servicelife. Lubricating parts as below
Blade Shaft Bearing Smear Every 3 months Lime grease
Motor Bearing Smear Every 6 months Lime grease
Front and Back
Worktables
Worktable
Screw Oil Pot Weekly Machine oil
Dovetail Oil Pot Weekly Machine oil
Chapter 10: Safety rules
1. The machine must be operated by trained professionals older than 18.
2. Before working, put on protective equipment, tie up cuff and long hair, and take off theornaments.
3. The working area should be bright and commodious. Leave enough room for operation andkeep others away except operators.
4. Forbid operation by operators who is sick or drunk or takes chemicals or drug.
5. Do not be away in the process. And keep children away during or after the process.
6. Do not open any protective device in the process.
7. Prohibit of overload or long-time working.
8. Do not put any other things on the top in process.
9. Power off after the machine stop running and then do examination.
10. The width and height of the processed wood piece should be within the standard of themachine.
11. Besides terms above, some unexpected trouble as follows may occur: fault during planing,error in blade assembling, wrong wiring connecting etc. Safety also lies in yourself.
Chapter 11: Troubles and solutions
1 Power on but the motor Does not run.
2 Halt while processing
a) loose connection or off line
b) bad connection of switch
c) lack of phase
a) lack of phase or power off
b) overload working
3 Spindle does not run when motor works
Loose or worn belt
Chapter 12: List of quick-wear parts
a) check the connecting wire
b) check or change the switch
c) Check the circuit
a) check the power wire with multimeter
b) adjust the load
Tighten or change the belt
Chapter 13: Attention
The right to interpret the operating manual belongs to our company. No company or person is allowed to copy. High speed and innovation are our developing strategies. We keep the right to improve our product continually without previous note. The customized product of special structure is exclusive in the manual.